The following information is also available:
Time column is TIME ORDERED-> Fetching fa930701_0242.1244.Z
Time column is TIME ORDERED-> Fetching fa930701_1244.0420.Z
fa930701_0242.1244 fa930701_1244.0420-> Checking if column TIME in merged.tmp is in order
Time column is TIME ORDERED-> Running attitude FTOOL on merged attitude file
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 15648141.360000 15740442.069500
Data file start and stop ascatime : 15648141.360000 15740442.069500
Aspecting run start and stop ascatime : 15648141.360077 15740442.069411
Time interval averaged over (seconds) : 92300.709334
Total pointing and manuver time (sec) : 92299.984375 1.000035
Mean boresight Euler angles : 308.001780 52.541982 57.010025
RA DEC SUN ANGLE
Mean solar position (deg) : 99.62 23.15
Mean aberration (arcsec) : 22.35 -5.20
Mean sat X-axis (deg) : 16.457404 -25.608372 94.08
Mean sat Y-axis (deg) : 81.135073 41.744624 24.17
Mean sat Z-axis (deg) : 308.001780 37.458018 113.77
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 308.034485 37.741089 326.990051 0.793744
Minimum 308.027985 37.458588 326.910950 0.189404
Maximum 308.105743 37.887310 327.017883 16.977390
Sigma (RMS) 0.001038 0.005211 0.008235 2.259729
Number of ASPECT records processed = 88239
Aspecting to RA/DEC : 308.03448486 37.74108887
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 308.034 DEC: 37.741
START TIME: SC 15648141.3601 = UT 01/07/93 02:42:21
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000096 16.885 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
169.499298 15.882 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1605.994263 14.874 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1661.494141 13.863 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1682.994019 12.859 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1702.994019 11.858 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1723.993774 10.857 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1744.493652 9.839 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1766.993652 8.817 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1791.493652 7.815 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1817.493530 6.810 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1846.993286 5.793 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1880.493286 4.781 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1920.493164 3.769 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1968.493042 2.764 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2035.992676 1.758 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2175.992188 0.750 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
92300.210938 9.349 800 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
92300.710938 9.400 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Attitude Records: 88239
Attitude Steps: 19
Maneuver ACM time: 1.00000 sec
Pointed ACM time: 92300.3 sec
-> Calculating aspect point97 70 count=6436 sum1=1.98228e+06 sum2=338102 sum3=366945 97 71 count=61850 sum1=1.90498e+07 sum2=3.24934e+06 sum3=3.52621e+06 98 70 count=262 sum1=80696.8 sum2=13763.6 sum3=14936.3 98 71 count=12793 sum1=3.94028e+06 sum2=672098 sum3=729300 99 70 count=4234 sum1=1.30414e+06 sum2=222414 sum3=241346 99 71 count=79 sum1=24333.1 sum2=4150.47 sum3=4503.14 99 72 count=22 sum1=6776.36 sum2=1156.07 sum3=1254 99 73 count=16 sum1=4928.3 sum2=840.93 sum3=911.986 99 74 count=8 sum1=2464.16 sum2=420.534 sum3=455.984 99 97 count=867 sum1=267051 sum2=45777.5 sum3=49383.6 99 98 count=177 sum1=54519.1 sum2=9346.63 sum3=10080.8 99 99 count=17 sum1=5236.34 sum2=897.905 sum3=968.023 100 74 count=4 sum1=1232.09 sum2=210.287 sum3=227.99 100 75 count=13 sum1=4004.31 sum2=683.546 sum3=740.952 100 76 count=60 sum1=18481.6 sum2=3155.3 sum3=3419.74 100 77 count=54 sum1=16633.5 sum2=2840.31 sum3=3077.7 100 78 count=53 sum1=16325.6 sum2=2788.27 sum3=3020.64 100 79 count=13 sum1=4004.42 sum2=684.008 sum3=740.909 100 97 count=104 sum1=32034.8 sum2=5490.85 sum3=5924.1 100 100 count=2 sum1=616.044 sum2=105.648 sum3=113.864 101 79 count=26 sum1=8008.87 sum2=1368.13 sum3=1481.79 101 80 count=38 sum1=11705.3 sum2=1999.88 sum3=2165.66 101 81 count=38 sum1=11705.4 sum2=2000.26 sum3=2165.61 101 82 count=33 sum1=10165.3 sum2=1737.4 sum3=1880.63 101 83 count=23 sum1=7084.96 sum2=1211.11 sum3=1310.71 101 96 count=45 sum1=13861.8 sum2=2375.73 sum3=2563.42 101 97 count=47 sum1=14477.6 sum2=2481.37 sum3=2677.32 102 83 count=10 sum1=3080.43 sum2=526.618 sum3=569.879 102 84 count=29 sum1=8933.3 sum2=1527.39 sum3=1652.58 102 85 count=32 sum1=9857.51 sum2=1685.72 sum3=1823.53 102 86 count=24 sum1=7393.19 sum2=1264.54 sum3=1367.59 102 87 count=10 sum1=3080.51 sum2=526.955 sum3=569.822 102 96 count=100 sum1=30804.7 sum2=5279.25 sum3=5696.56 103 87 count=17 sum1=5236.89 sum2=895.904 sum3=968.71 103 88 count=25 sum1=7701.35 sum2=1317.71 sum3=1424.53 103 89 count=27 sum1=8317.53 sum2=1423.42 sum3=1538.45 103 90 count=23 sum1=7085.36 sum2=1212.76 sum3=1310.52 103 91 count=10 sum1=3080.61 sum2=527.36 sum3=569.783 103 96 count=146 sum1=44976.3 sum2=7707.42 sum3=8317.41 104 91 count=10 sum1=3080.62 sum2=527.41 sum3=569.771 104 92 count=35 sum1=10782.2 sum2=1846.22 sum3=1994.17 104 93 count=21 sum1=6469.39 sum2=1107.93 sum3=1196.48 104 94 count=51 sum1=15711.5 sum2=2691.24 sum3=2905.65 104 95 count=68 sum1=20948.8 sum2=3588.96 sum3=3874.08 104 96 count=239 sum1=73628.1 sum2=12616.4 sum3=13615.7 105 57 count=2 sum1=616.147 sum2=104.793 sum3=114.074 105 96 count=45 sum1=13863.2 sum2=2375.39 sum3=2563.65 0 out of 88238 points outside bin structure-> Euler angles: 308, 52.5357, 57.0117
Interpolating 16 records in time interval 1.57404e+07 - 1.57404e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft930701_0242.1244",,,"frf telemetry file" frf_file,s,h,"ft930701_1244.0420",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft930701_0242.1244 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 0 Bright = 704640 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 704640 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 11047 no. of SIS events found = 301564 ASCA format Telemetry file: ft930701_1244.0420 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 1 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 0 Bright = 708416 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 708416 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 11088 no. of SIS events found = 612526-> Standard Error Output From FTOOL frfread
coordinate error 509 109 coordinate error 0 0 coordinate error 384 0 coordinate error 0 56 coordinate error 448 0 coordinate error 0 1 coordinate error 505 134 coordinate error 239 467 coordinate error 0 0 coordinate error 336 0 coordinate error 1 187 coordinate error 0 0 coordinate error 0 0 coordinate error 320 0 coordinate error 287 458 coordinate error 0 6 coordinate error 368 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 96 coordinate error 0 12 coordinate error 0 12 coordinate error 0 0 coordinate error 0 0 coordinate error 0 1 coordinate error 1 256 coordinate error 0 0 coordinate error 256 0 coordinate error 0 96 coordinate error 1 256 coordinate error 192 0 coordinate error 48 0 coordinate error 0 0 coordinate error 0 1-> Removing the following files with NEVENTS=0
ft930701_0242_1244G200470H.fits ft930701_0242_1244G200570M.fits ft930701_0242_1244G200699.fits ft930701_0242_1244G200770M.fits ft930701_0242_1244G201270H.fits ft930701_0242_1244G201370L.fits ft930701_0242_1244G201470H.fits ft930701_0242_1244G201570H.fits ft930701_0242_1244G201670H.fits ft930701_0242_1244G201770H.fits ft930701_0242_1244G202299.fits ft930701_0242_1244G202470H.fits ft930701_0242_1244G202570H.fits ft930701_0242_1244G202670L.fits ft930701_0242_1244G202770L.fits ft930701_0242_1244G202870H.fits ft930701_0242_1244G202970H.fits ft930701_0242_1244G203070H.fits ft930701_0242_1244G203170H.fits ft930701_0242_1244G203899.fits ft930701_0242_1244G204070H.fits ft930701_0242_1244G204170H.fits ft930701_0242_1244G204270L.fits ft930701_0242_1244G204570H.fits ft930701_0242_1244G204670H.fits ft930701_0242_1244G204770L.fits ft930701_0242_1244G205070H.fits ft930701_0242_1244G205170H.fits ft930701_0242_1244G205270L.fits ft930701_0242_1244G205370H.fits ft930701_0242_1244G205470H.fits ft930701_0242_1244G205570H.fits ft930701_0242_1244G300470H.fits ft930701_0242_1244G300570M.fits ft930701_0242_1244G300699.fits ft930701_0242_1244G300770M.fits ft930701_0242_1244G301270H.fits ft930701_0242_1244G301370L.fits ft930701_0242_1244G301470H.fits ft930701_0242_1244G301570H.fits ft930701_0242_1244G301670H.fits ft930701_0242_1244G301770H.fits ft930701_0242_1244G301870H.fits ft930701_0242_1244G302299.fits ft930701_0242_1244G302470H.fits ft930701_0242_1244G302570H.fits ft930701_0242_1244G302670L.fits ft930701_0242_1244G302770L.fits ft930701_0242_1244G302870H.fits ft930701_0242_1244G302970H.fits ft930701_0242_1244G303070H.fits ft930701_0242_1244G303170H.fits ft930701_0242_1244G303270H.fits ft930701_0242_1244G303699.fits ft930701_0242_1244G303870H.fits ft930701_0242_1244G303970H.fits ft930701_0242_1244G304070L.fits ft930701_0242_1244G304370H.fits ft930701_0242_1244G304470H.fits ft930701_0242_1244G304570L.fits ft930701_0242_1244G304870H.fits ft930701_0242_1244G304970H.fits ft930701_0242_1244G305070L.fits ft930701_0242_1244G305170H.fits ft930701_0242_1244G305270H.fits ft930701_0242_1244S000302H.fits ft930701_0242_1244S000699.fits ft930701_0242_1244S001102M.fits ft930701_0242_1244S001602H.fits ft930701_0242_1244S001799.fits ft930701_0242_1244S002002L.fits ft930701_0242_1244S002102L.fits ft930701_0242_1244S002399.fits ft930701_0242_1244S002702L.fits ft930701_0242_1244S003002L.fits ft930701_0242_1244S003102L.fits ft930701_0242_1244S003402L.fits ft930701_0242_1244S003502L.fits ft930701_0242_1244S100302H.fits ft930701_0242_1244S100699.fits ft930701_0242_1244S101799.fits ft930701_0242_1244S102002L.fits ft930701_0242_1244S102399.fits ft930701_0242_1244S102702L.fits ft930701_0242_1244S103002L.fits ft930701_0242_1244S103102L.fits ft930701_0242_1244S103402L.fits ft930701_0242_1244S103502L.fits ft930701_1244_0420G200370M.fits ft930701_1244_0420G200470M.fits ft930701_1244_0420G200570L.fits ft930701_1244_0420G201170M.fits ft930701_1244_0420G201270M.fits ft930701_1244_0420G201370L.fits ft930701_1244_0420G204970M.fits ft930701_1244_0420G205099.fits ft930701_1244_0420G205970H.fits ft930701_1244_0420G300370M.fits ft930701_1244_0420G300470M.fits ft930701_1244_0420G300570L.fits ft930701_1244_0420G301170M.fits ft930701_1244_0420G301270M.fits ft930701_1244_0420G301370L.fits ft930701_1244_0420G305170M.fits ft930701_1244_0420G305299.fits ft930701_1244_0420G306170H.fits ft930701_1244_0420G306270H.fits ft930701_1244_0420S000402L.fits ft930701_1244_0420S000902L.fits ft930701_1244_0420S002502M.fits ft930701_1244_0420S003102M.fits ft930701_1244_0420S003202L.fits ft930701_1244_0420S003302L.fits ft930701_1244_0420S003402H.fits ft930701_1244_0420S004002H.fits ft930701_1244_0420S004399.fits ft930701_1244_0420S004802M.fits ft930701_1244_0420S005302M.fits ft930701_1244_0420S100402L.fits ft930701_1244_0420S100902L.fits ft930701_1244_0420S102502M.fits ft930701_1244_0420S103102M.fits ft930701_1244_0420S103202L.fits ft930701_1244_0420S103402H.fits ft930701_1244_0420S104002H.fits ft930701_1244_0420S104399.fits-> Checking for empty GTI extensions
ft930701_0242_1244S000102M.fits[3] ft930701_0242_1244S000202H.fits[3] ft930701_0242_1244S000402H.fits[3] ft930701_0242_1244S000502M.fits[3] ft930701_0242_1244S000702M.fits[3] ft930701_0242_1244S000802L.fits[3] ft930701_0242_1244S000902L.fits[3] ft930701_0242_1244S001002L.fits[3] ft930701_0242_1244S001202H.fits[3] ft930701_0242_1244S001302L.fits[3] ft930701_0242_1244S001402L.fits[3] ft930701_0242_1244S001502L.fits[3] ft930701_0242_1244S001802H.fits[3] ft930701_0242_1244S001902L.fits[3] ft930701_0242_1244S002202H.fits[3] ft930701_0242_1244S002402H.fits[3] ft930701_0242_1244S002502L.fits[3] ft930701_0242_1244S002602L.fits[3] ft930701_0242_1244S002802H.fits[3] ft930701_0242_1244S002902L.fits[3] ft930701_0242_1244S003202H.fits[3] ft930701_0242_1244S003302H.fits[3] ft930701_0242_1244S003602H.fits[3] ft930701_1244_0420S000102H.fits[3] ft930701_1244_0420S000202M.fits[3] ft930701_1244_0420S000302M.fits[3] ft930701_1244_0420S000502L.fits[3] ft930701_1244_0420S000602M.fits[3] ft930701_1244_0420S000702H.fits[3] ft930701_1244_0420S000802M.fits[3] ft930701_1244_0420S001002L.fits[3] ft930701_1244_0420S001102M.fits[3] ft930701_1244_0420S001202L.fits[3] ft930701_1244_0420S001302H.fits[3] ft930701_1244_0420S001402L.fits[3] ft930701_1244_0420S001502M.fits[3] ft930701_1244_0420S001602H.fits[3] ft930701_1244_0420S001702M.fits[3] ft930701_1244_0420S001802M.fits[3] ft930701_1244_0420S001902M.fits[3] ft930701_1244_0420S002002L.fits[3] ft930701_1244_0420S002102M.fits[3] ft930701_1244_0420S002202H.fits[3] ft930701_1244_0420S002302M.fits[3] ft930701_1244_0420S002402M.fits[3] ft930701_1244_0420S002602L.fits[3] ft930701_1244_0420S002702M.fits[3] ft930701_1244_0420S002802M.fits[3] ft930701_1244_0420S002902H.fits[3] ft930701_1244_0420S003002M.fits[3] ft930701_1244_0420S003502H.fits[3] ft930701_1244_0420S003602L.fits[3] ft930701_1244_0420S003702H.fits[3] ft930701_1244_0420S003802M.fits[3] ft930701_1244_0420S003902H.fits[3] ft930701_1244_0420S004102H.fits[3] ft930701_1244_0420S004202M.fits[3] ft930701_1244_0420S004402L.fits[3] ft930701_1244_0420S004502L.fits[3] ft930701_1244_0420S004602L.fits[3] ft930701_1244_0420S004702H.fits[3] ft930701_1244_0420S004902H.fits[3] ft930701_1244_0420S005002L.fits[3] ft930701_1244_0420S005102L.fits[3] ft930701_1244_0420S005202L.fits[3] ft930701_1244_0420S005402H.fits[3]-> Merging GTIs from the following files:
ft930701_0242_1244S100102M.fits[3] ft930701_0242_1244S100202H.fits[3] ft930701_0242_1244S100402H.fits[3] ft930701_0242_1244S100502M.fits[3] ft930701_0242_1244S100702M.fits[3] ft930701_0242_1244S100802L.fits[3] ft930701_0242_1244S100902L.fits[3] ft930701_0242_1244S101002L.fits[3] ft930701_0242_1244S101102M.fits[3] ft930701_0242_1244S101202H.fits[3] ft930701_0242_1244S101302L.fits[3] ft930701_0242_1244S101402L.fits[3] ft930701_0242_1244S101502L.fits[3] ft930701_0242_1244S101602H.fits[3] ft930701_0242_1244S101802H.fits[3] ft930701_0242_1244S101902L.fits[3] ft930701_0242_1244S102102L.fits[3] ft930701_0242_1244S102202H.fits[3] ft930701_0242_1244S102402H.fits[3] ft930701_0242_1244S102502L.fits[3] ft930701_0242_1244S102602L.fits[3] ft930701_0242_1244S102802H.fits[3] ft930701_0242_1244S102902L.fits[3] ft930701_0242_1244S103202H.fits[3] ft930701_0242_1244S103302H.fits[3] ft930701_0242_1244S103602H.fits[3] ft930701_1244_0420S100102H.fits[3] ft930701_1244_0420S100202M.fits[3] ft930701_1244_0420S100302M.fits[3] ft930701_1244_0420S100502L.fits[3] ft930701_1244_0420S100602M.fits[3] ft930701_1244_0420S100702H.fits[3] ft930701_1244_0420S100802M.fits[3] ft930701_1244_0420S101002L.fits[3] ft930701_1244_0420S101102M.fits[3] ft930701_1244_0420S101202L.fits[3] ft930701_1244_0420S101302H.fits[3] ft930701_1244_0420S101402L.fits[3] ft930701_1244_0420S101502M.fits[3] ft930701_1244_0420S101602H.fits[3] ft930701_1244_0420S101702M.fits[3] ft930701_1244_0420S101802M.fits[3] ft930701_1244_0420S101902M.fits[3] ft930701_1244_0420S102002L.fits[3] ft930701_1244_0420S102102M.fits[3] ft930701_1244_0420S102202H.fits[3] ft930701_1244_0420S102302M.fits[3] ft930701_1244_0420S102402M.fits[3] ft930701_1244_0420S102602L.fits[3] ft930701_1244_0420S102702M.fits[3] ft930701_1244_0420S102802M.fits[3] ft930701_1244_0420S102902H.fits[3] ft930701_1244_0420S103002M.fits[3] ft930701_1244_0420S103302L.fits[3] ft930701_1244_0420S103502H.fits[3] ft930701_1244_0420S103602L.fits[3] ft930701_1244_0420S103702H.fits[3] ft930701_1244_0420S103802M.fits[3] ft930701_1244_0420S103902H.fits[3] ft930701_1244_0420S104102H.fits[3] ft930701_1244_0420S104202M.fits[3] ft930701_1244_0420S104402L.fits[3] ft930701_1244_0420S104502L.fits[3] ft930701_1244_0420S104602L.fits[3] ft930701_1244_0420S104702H.fits[3] ft930701_1244_0420S104802M.fits[3] ft930701_1244_0420S104902H.fits[3] ft930701_1244_0420S105002L.fits[3] ft930701_1244_0420S105102L.fits[3] ft930701_1244_0420S105202L.fits[3] ft930701_1244_0420S105302M.fits[3] ft930701_1244_0420S105402H.fits[3]-> Merging GTIs from the following files:
ft930701_0242_1244G200170M.fits[3] ft930701_0242_1244G200270H.fits[3] ft930701_0242_1244G200370H.fits[3] ft930701_0242_1244G200870L.fits[3] ft930701_0242_1244G200970M.fits[3] ft930701_0242_1244G201070H.fits[3] ft930701_0242_1244G201170H.fits[3] ft930701_0242_1244G201870H.fits[3] ft930701_0242_1244G201970H.fits[3] ft930701_0242_1244G202070H.fits[3] ft930701_0242_1244G202170H.fits[3] ft930701_0242_1244G202370H.fits[3] ft930701_0242_1244G203270H.fits[3] ft930701_0242_1244G203370H.fits[3] ft930701_0242_1244G203470H.fits[3] ft930701_0242_1244G203570H.fits[3] ft930701_0242_1244G203670H.fits[3] ft930701_0242_1244G203770H.fits[3] ft930701_0242_1244G203970H.fits[3] ft930701_0242_1244G204370L.fits[3] ft930701_0242_1244G204470H.fits[3] ft930701_0242_1244G204870L.fits[3] ft930701_0242_1244G204970H.fits[3] ft930701_0242_1244G205670H.fits[3] ft930701_0242_1244G205770H.fits[3] ft930701_1244_0420G200170H.fits[3] ft930701_1244_0420G200270M.fits[3] ft930701_1244_0420G200670L.fits[3] ft930701_1244_0420G200770L.fits[3] ft930701_1244_0420G200870M.fits[3] ft930701_1244_0420G200970H.fits[3] ft930701_1244_0420G201070M.fits[3] ft930701_1244_0420G201470L.fits[3] ft930701_1244_0420G201570L.fits[3] ft930701_1244_0420G201670M.fits[3] ft930701_1244_0420G201770M.fits[3] ft930701_1244_0420G201870M.fits[3] ft930701_1244_0420G201970M.fits[3] ft930701_1244_0420G202070L.fits[3] ft930701_1244_0420G202170H.fits[3] ft930701_1244_0420G202270L.fits[3] ft930701_1244_0420G202370L.fits[3] ft930701_1244_0420G202470M.fits[3] ft930701_1244_0420G202570H.fits[3] ft930701_1244_0420G202670M.fits[3] ft930701_1244_0420G202770L.fits[3] ft930701_1244_0420G202870L.fits[3] ft930701_1244_0420G202970M.fits[3] ft930701_1244_0420G203070M.fits[3] ft930701_1244_0420G203170M.fits[3] ft930701_1244_0420G203270M.fits[3] ft930701_1244_0420G203370H.fits[3] ft930701_1244_0420G203470M.fits[3] ft930701_1244_0420G203570L.fits[3] ft930701_1244_0420G203670M.fits[3] ft930701_1244_0420G203770H.fits[3] ft930701_1244_0420G203870M.fits[3] ft930701_1244_0420G203970L.fits[3] ft930701_1244_0420G204070H.fits[3] ft930701_1244_0420G204170L.fits[3] ft930701_1244_0420G204270L.fits[3] ft930701_1244_0420G204370L.fits[3] ft930701_1244_0420G204470H.fits[3] ft930701_1244_0420G204570M.fits[3] ft930701_1244_0420G204670H.fits[3] ft930701_1244_0420G204770M.fits[3] ft930701_1244_0420G204870M.fits[3] ft930701_1244_0420G205170L.fits[3] ft930701_1244_0420G205270L.fits[3] ft930701_1244_0420G205370H.fits[3] ft930701_1244_0420G205470H.fits[3] ft930701_1244_0420G205570H.fits[3] ft930701_1244_0420G205670H.fits[3] ft930701_1244_0420G205770M.fits[3] ft930701_1244_0420G205870H.fits[3] ft930701_1244_0420G206070L.fits[3] ft930701_1244_0420G206170L.fits[3] ft930701_1244_0420G206270M.fits[3] ft930701_1244_0420G206370H.fits[3]-> Merging GTIs from the following files:
ft930701_0242_1244G300170M.fits[3] ft930701_0242_1244G300270H.fits[3] ft930701_0242_1244G300370H.fits[3] ft930701_0242_1244G300870L.fits[3] ft930701_0242_1244G300970M.fits[3] ft930701_0242_1244G301070H.fits[3] ft930701_0242_1244G301170H.fits[3] ft930701_0242_1244G301970H.fits[3] ft930701_0242_1244G302070H.fits[3] ft930701_0242_1244G302170H.fits[3] ft930701_0242_1244G302370H.fits[3] ft930701_0242_1244G303370H.fits[3] ft930701_0242_1244G303470H.fits[3] ft930701_0242_1244G303570H.fits[3] ft930701_0242_1244G303770H.fits[3] ft930701_0242_1244G304170L.fits[3] ft930701_0242_1244G304270H.fits[3] ft930701_0242_1244G304670L.fits[3] ft930701_0242_1244G304770H.fits[3] ft930701_0242_1244G305370H.fits[3] ft930701_0242_1244G305470H.fits[3] ft930701_0242_1244G305570H.fits[3] ft930701_1244_0420G300170H.fits[3] ft930701_1244_0420G300270M.fits[3] ft930701_1244_0420G300670L.fits[3] ft930701_1244_0420G300770L.fits[3] ft930701_1244_0420G300870M.fits[3] ft930701_1244_0420G300970H.fits[3] ft930701_1244_0420G301070M.fits[3] ft930701_1244_0420G301470L.fits[3] ft930701_1244_0420G301570L.fits[3] ft930701_1244_0420G301670M.fits[3] ft930701_1244_0420G301770M.fits[3] ft930701_1244_0420G301870M.fits[3] ft930701_1244_0420G301970M.fits[3] ft930701_1244_0420G302070L.fits[3] ft930701_1244_0420G302170L.fits[3] ft930701_1244_0420G302270H.fits[3] ft930701_1244_0420G302370H.fits[3] ft930701_1244_0420G302470L.fits[3] ft930701_1244_0420G302570L.fits[3] ft930701_1244_0420G302670M.fits[3] ft930701_1244_0420G302770H.fits[3] ft930701_1244_0420G302870M.fits[3] ft930701_1244_0420G302970L.fits[3] ft930701_1244_0420G303070L.fits[3] ft930701_1244_0420G303170M.fits[3] ft930701_1244_0420G303270M.fits[3] ft930701_1244_0420G303370M.fits[3] ft930701_1244_0420G303470M.fits[3] ft930701_1244_0420G303570H.fits[3] ft930701_1244_0420G303670M.fits[3] ft930701_1244_0420G303770L.fits[3] ft930701_1244_0420G303870M.fits[3] ft930701_1244_0420G303970H.fits[3] ft930701_1244_0420G304070M.fits[3] ft930701_1244_0420G304170L.fits[3] ft930701_1244_0420G304270H.fits[3] ft930701_1244_0420G304370L.fits[3] ft930701_1244_0420G304470L.fits[3] ft930701_1244_0420G304570L.fits[3] ft930701_1244_0420G304670H.fits[3] ft930701_1244_0420G304770M.fits[3] ft930701_1244_0420G304870H.fits[3] ft930701_1244_0420G304970M.fits[3] ft930701_1244_0420G305070M.fits[3] ft930701_1244_0420G305370L.fits[3] ft930701_1244_0420G305470L.fits[3] ft930701_1244_0420G305570H.fits[3] ft930701_1244_0420G305670H.fits[3] ft930701_1244_0420G305770H.fits[3] ft930701_1244_0420G305870H.fits[3] ft930701_1244_0420G305970M.fits[3] ft930701_1244_0420G306070H.fits[3] ft930701_1244_0420G306370L.fits[3] ft930701_1244_0420G306470L.fits[3] ft930701_1244_0420G306570M.fits[3] ft930701_1244_0420G306670H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 2 photon cnt = 9 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g200470h.prelist merge count = 3 photon cnt = 12 GISSORTSPLIT:LO:g200570h.prelist merge count = 10 photon cnt = 139026 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g200170l.prelist merge count = 3 photon cnt = 60 GISSORTSPLIT:LO:g200170m.prelist merge count = 2 photon cnt = 3152 GISSORTSPLIT:LO:Total filenames split = 25 GISSORTSPLIT:LO:Total split file cnt = 8 GISSORTSPLIT:LO:End program-> Creating ad40020000g200170h.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244G200270H.fits 2 -- ft930701_0242_1244G201070H.fits 3 -- ft930701_0242_1244G202170H.fits 4 -- ft930701_0242_1244G202370H.fits 5 -- ft930701_0242_1244G203570H.fits 6 -- ft930701_0242_1244G203770H.fits 7 -- ft930701_0242_1244G203970H.fits 8 -- ft930701_0242_1244G204470H.fits 9 -- ft930701_0242_1244G204970H.fits 10 -- ft930701_0242_1244G205770H.fits Merging binary extension #: 2 1 -- ft930701_0242_1244G200270H.fits 2 -- ft930701_0242_1244G201070H.fits 3 -- ft930701_0242_1244G202170H.fits 4 -- ft930701_0242_1244G202370H.fits 5 -- ft930701_0242_1244G203570H.fits 6 -- ft930701_0242_1244G203770H.fits 7 -- ft930701_0242_1244G203970H.fits 8 -- ft930701_0242_1244G204470H.fits 9 -- ft930701_0242_1244G204970H.fits 10 -- ft930701_0242_1244G205770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g200270m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244G200170M.fits 2 -- ft930701_0242_1244G200970M.fits Merging binary extension #: 2 1 -- ft930701_0242_1244G200170M.fits 2 -- ft930701_0242_1244G200970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000060 events
ft930701_0242_1244G200870L.fits ft930701_0242_1244G204370L.fits ft930701_0242_1244G204870L.fits-> Ignoring the following files containing 000000013 events
ft930701_0242_1244G203670H.fits-> Ignoring the following files containing 000000012 events
ft930701_0242_1244G202070H.fits ft930701_0242_1244G203470H.fits ft930701_0242_1244G205670H.fits-> Ignoring the following files containing 000000009 events
ft930701_0242_1244G200370H.fits ft930701_0242_1244G201170H.fits-> Ignoring the following files containing 000000005 events
ft930701_0242_1244G201970H.fits ft930701_0242_1244G203370H.fits-> Ignoring the following files containing 000000005 events
ft930701_0242_1244G201870H.fits ft930701_0242_1244G203270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 2 photon cnt = 12 GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g300370h.prelist merge count = 3 photon cnt = 6 GISSORTSPLIT:LO:g300470h.prelist merge count = 9 photon cnt = 167616 GISSORTSPLIT:LO:g300170l.prelist merge count = 3 photon cnt = 56 GISSORTSPLIT:LO:g300170m.prelist merge count = 2 photon cnt = 3239 GISSORTSPLIT:LO:Total filenames split = 22 GISSORTSPLIT:LO:Total split file cnt = 6 GISSORTSPLIT:LO:End program-> Creating ad40020000g300170h.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244G300270H.fits 2 -- ft930701_0242_1244G301070H.fits 3 -- ft930701_0242_1244G302170H.fits 4 -- ft930701_0242_1244G302370H.fits 5 -- ft930701_0242_1244G303570H.fits 6 -- ft930701_0242_1244G303770H.fits 7 -- ft930701_0242_1244G304270H.fits 8 -- ft930701_0242_1244G304770H.fits 9 -- ft930701_0242_1244G305570H.fits Merging binary extension #: 2 1 -- ft930701_0242_1244G300270H.fits 2 -- ft930701_0242_1244G301070H.fits 3 -- ft930701_0242_1244G302170H.fits 4 -- ft930701_0242_1244G302370H.fits 5 -- ft930701_0242_1244G303570H.fits 6 -- ft930701_0242_1244G303770H.fits 7 -- ft930701_0242_1244G304270H.fits 8 -- ft930701_0242_1244G304770H.fits 9 -- ft930701_0242_1244G305570H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g300270m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244G300170M.fits 2 -- ft930701_0242_1244G300970M.fits Merging binary extension #: 2 1 -- ft930701_0242_1244G300170M.fits 2 -- ft930701_0242_1244G300970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000056 events
ft930701_0242_1244G300870L.fits ft930701_0242_1244G304170L.fits ft930701_0242_1244G304670L.fits-> Ignoring the following files containing 000000012 events
ft930701_0242_1244G300370H.fits ft930701_0242_1244G301170H.fits-> Ignoring the following files containing 000000007 events
ft930701_0242_1244G301970H.fits ft930701_0242_1244G303370H.fits ft930701_0242_1244G305370H.fits-> Ignoring the following files containing 000000006 events
ft930701_0242_1244G302070H.fits ft930701_0242_1244G303470H.fits ft930701_0242_1244G305470H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000102h.prelist merge count = 9 photon cnt = 135344 SIS0SORTSPLIT:LO:s000202h.prelist merge count = 1 photon cnt = 71 SIS0SORTSPLIT:LO:s000302l.prelist merge count = 7 photon cnt = 14091 SIS0SORTSPLIT:LO:s000402l.prelist merge count = 3 photon cnt = 159 SIS0SORTSPLIT:LO:s000502m.prelist merge count = 3 photon cnt = 1196 SIS0SORTSPLIT:LO:Total filenames split = 23 SIS0SORTSPLIT:LO:Total split file cnt = 5 SIS0SORTSPLIT:LO:End program-> Creating ad40020000s000102h.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S000202H.fits 2 -- ft930701_0242_1244S000402H.fits 3 -- ft930701_0242_1244S001202H.fits 4 -- ft930701_0242_1244S001802H.fits 5 -- ft930701_0242_1244S002202H.fits 6 -- ft930701_0242_1244S002402H.fits 7 -- ft930701_0242_1244S002802H.fits 8 -- ft930701_0242_1244S003202H.fits 9 -- ft930701_0242_1244S003602H.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S000202H.fits 2 -- ft930701_0242_1244S000402H.fits 3 -- ft930701_0242_1244S001202H.fits 4 -- ft930701_0242_1244S001802H.fits 5 -- ft930701_0242_1244S002202H.fits 6 -- ft930701_0242_1244S002402H.fits 7 -- ft930701_0242_1244S002802H.fits 8 -- ft930701_0242_1244S003202H.fits 9 -- ft930701_0242_1244S003602H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s000202l.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S000802L.fits 2 -- ft930701_0242_1244S001002L.fits 3 -- ft930701_0242_1244S001302L.fits 4 -- ft930701_0242_1244S001502L.fits 5 -- ft930701_0242_1244S001902L.fits 6 -- ft930701_0242_1244S002502L.fits 7 -- ft930701_0242_1244S002902L.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S000802L.fits 2 -- ft930701_0242_1244S001002L.fits 3 -- ft930701_0242_1244S001302L.fits 4 -- ft930701_0242_1244S001502L.fits 5 -- ft930701_0242_1244S001902L.fits 6 -- ft930701_0242_1244S002502L.fits 7 -- ft930701_0242_1244S002902L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s000302m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S000102M.fits 2 -- ft930701_0242_1244S000502M.fits 3 -- ft930701_0242_1244S000702M.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S000102M.fits 2 -- ft930701_0242_1244S000502M.fits 3 -- ft930701_0242_1244S000702M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000159 events
ft930701_0242_1244S000902L.fits ft930701_0242_1244S001402L.fits ft930701_0242_1244S002602L.fits-> Ignoring the following files containing 000000071 events
ft930701_0242_1244S003302H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100102h.prelist merge count = 10 photon cnt = 133634 SIS1SORTSPLIT:LO:s100202h.prelist merge count = 1 photon cnt = 65 SIS1SORTSPLIT:LO:s100302l.prelist merge count = 8 photon cnt = 15058 SIS1SORTSPLIT:LO:s100402l.prelist merge count = 3 photon cnt = 155 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 4 photon cnt = 1774 SIS1SORTSPLIT:LO:Total filenames split = 26 SIS1SORTSPLIT:LO:Total split file cnt = 5 SIS1SORTSPLIT:LO:End program-> Creating ad40020000s100102h.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S100202H.fits 2 -- ft930701_0242_1244S100402H.fits 3 -- ft930701_0242_1244S101202H.fits 4 -- ft930701_0242_1244S101602H.fits 5 -- ft930701_0242_1244S101802H.fits 6 -- ft930701_0242_1244S102202H.fits 7 -- ft930701_0242_1244S102402H.fits 8 -- ft930701_0242_1244S102802H.fits 9 -- ft930701_0242_1244S103202H.fits 10 -- ft930701_0242_1244S103602H.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S100202H.fits 2 -- ft930701_0242_1244S100402H.fits 3 -- ft930701_0242_1244S101202H.fits 4 -- ft930701_0242_1244S101602H.fits 5 -- ft930701_0242_1244S101802H.fits 6 -- ft930701_0242_1244S102202H.fits 7 -- ft930701_0242_1244S102402H.fits 8 -- ft930701_0242_1244S102802H.fits 9 -- ft930701_0242_1244S103202H.fits 10 -- ft930701_0242_1244S103602H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s100202l.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S100802L.fits 2 -- ft930701_0242_1244S101002L.fits 3 -- ft930701_0242_1244S101302L.fits 4 -- ft930701_0242_1244S101502L.fits 5 -- ft930701_0242_1244S101902L.fits 6 -- ft930701_0242_1244S102102L.fits 7 -- ft930701_0242_1244S102502L.fits 8 -- ft930701_0242_1244S102902L.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S100802L.fits 2 -- ft930701_0242_1244S101002L.fits 3 -- ft930701_0242_1244S101302L.fits 4 -- ft930701_0242_1244S101502L.fits 5 -- ft930701_0242_1244S101902L.fits 6 -- ft930701_0242_1244S102102L.fits 7 -- ft930701_0242_1244S102502L.fits 8 -- ft930701_0242_1244S102902L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s100302m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_0242_1244S100102M.fits 2 -- ft930701_0242_1244S100502M.fits 3 -- ft930701_0242_1244S100702M.fits 4 -- ft930701_0242_1244S101102M.fits Merging binary extension #: 2 1 -- ft930701_0242_1244S100102M.fits 2 -- ft930701_0242_1244S100502M.fits 3 -- ft930701_0242_1244S100702M.fits 4 -- ft930701_0242_1244S101102M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000155 events
ft930701_0242_1244S100902L.fits ft930701_0242_1244S101402L.fits ft930701_0242_1244S102602L.fits-> Ignoring the following files containing 000000065 events
ft930701_0242_1244S103302H.fits-> Collecting GIS2 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 12 photon cnt = 172938 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g200170l.prelist merge count = 4 photon cnt = 135 GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 74 GISSORTSPLIT:LO:g200370l.prelist merge count = 1 photon cnt = 85 GISSORTSPLIT:LO:g200470l.prelist merge count = 10 photon cnt = 26016 GISSORTSPLIT:LO:g200570l.prelist merge count = 2 photon cnt = 498 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200270m.prelist merge count = 14 photon cnt = 100097 GISSORTSPLIT:LO:g200370m.prelist merge count = 2 photon cnt = 277 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 149 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 90 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 103 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 119 GISSORTSPLIT:LO:Total filenames split = 54 GISSORTSPLIT:LO:Total split file cnt = 16 GISSORTSPLIT:LO:End program-> Creating ad40020000g200370h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G200170H.fits 2 -- ft930701_1244_0420G200970H.fits 3 -- ft930701_1244_0420G202170H.fits 4 -- ft930701_1244_0420G202570H.fits 5 -- ft930701_1244_0420G203370H.fits 6 -- ft930701_1244_0420G203770H.fits 7 -- ft930701_1244_0420G204070H.fits 8 -- ft930701_1244_0420G204470H.fits 9 -- ft930701_1244_0420G204670H.fits 10 -- ft930701_1244_0420G205670H.fits 11 -- ft930701_1244_0420G205870H.fits 12 -- ft930701_1244_0420G206370H.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G200170H.fits 2 -- ft930701_1244_0420G200970H.fits 3 -- ft930701_1244_0420G202170H.fits 4 -- ft930701_1244_0420G202570H.fits 5 -- ft930701_1244_0420G203370H.fits 6 -- ft930701_1244_0420G203770H.fits 7 -- ft930701_1244_0420G204070H.fits 8 -- ft930701_1244_0420G204470H.fits 9 -- ft930701_1244_0420G204670H.fits 10 -- ft930701_1244_0420G205670H.fits 11 -- ft930701_1244_0420G205870H.fits 12 -- ft930701_1244_0420G206370H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g200470m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G200270M.fits 2 -- ft930701_1244_0420G200870M.fits 3 -- ft930701_1244_0420G201070M.fits 4 -- ft930701_1244_0420G201970M.fits 5 -- ft930701_1244_0420G202470M.fits 6 -- ft930701_1244_0420G202670M.fits 7 -- ft930701_1244_0420G203270M.fits 8 -- ft930701_1244_0420G203470M.fits 9 -- ft930701_1244_0420G203670M.fits 10 -- ft930701_1244_0420G203870M.fits 11 -- ft930701_1244_0420G204570M.fits 12 -- ft930701_1244_0420G204770M.fits 13 -- ft930701_1244_0420G205770M.fits 14 -- ft930701_1244_0420G206270M.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G200270M.fits 2 -- ft930701_1244_0420G200870M.fits 3 -- ft930701_1244_0420G201070M.fits 4 -- ft930701_1244_0420G201970M.fits 5 -- ft930701_1244_0420G202470M.fits 6 -- ft930701_1244_0420G202670M.fits 7 -- ft930701_1244_0420G203270M.fits 8 -- ft930701_1244_0420G203470M.fits 9 -- ft930701_1244_0420G203670M.fits 10 -- ft930701_1244_0420G203870M.fits 11 -- ft930701_1244_0420G204570M.fits 12 -- ft930701_1244_0420G204770M.fits 13 -- ft930701_1244_0420G205770M.fits 14 -- ft930701_1244_0420G206270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g200570l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G200770L.fits 2 -- ft930701_1244_0420G201570L.fits 3 -- ft930701_1244_0420G202070L.fits 4 -- ft930701_1244_0420G202370L.fits 5 -- ft930701_1244_0420G202870L.fits 6 -- ft930701_1244_0420G203570L.fits 7 -- ft930701_1244_0420G203970L.fits 8 -- ft930701_1244_0420G204370L.fits 9 -- ft930701_1244_0420G205270L.fits 10 -- ft930701_1244_0420G206170L.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G200770L.fits 2 -- ft930701_1244_0420G201570L.fits 3 -- ft930701_1244_0420G202070L.fits 4 -- ft930701_1244_0420G202370L.fits 5 -- ft930701_1244_0420G202870L.fits 6 -- ft930701_1244_0420G203570L.fits 7 -- ft930701_1244_0420G203970L.fits 8 -- ft930701_1244_0420G204370L.fits 9 -- ft930701_1244_0420G205270L.fits 10 -- ft930701_1244_0420G206170L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000498 events
ft930701_1244_0420G202270L.fits ft930701_1244_0420G202770L.fits-> Ignoring the following files containing 000000277 events
ft930701_1244_0420G201870M.fits ft930701_1244_0420G203170M.fits-> Ignoring the following files containing 000000149 events
ft930701_1244_0420G202970M.fits-> Ignoring the following files containing 000000135 events
ft930701_1244_0420G201470L.fits ft930701_1244_0420G204270L.fits ft930701_1244_0420G205170L.fits ft930701_1244_0420G206070L.fits-> Ignoring the following files containing 000000119 events
ft930701_1244_0420G201770M.fits-> Ignoring the following files containing 000000103 events
ft930701_1244_0420G201670M.fits-> Ignoring the following files containing 000000090 events
ft930701_1244_0420G203070M.fits-> Ignoring the following files containing 000000085 events
ft930701_1244_0420G200670L.fits-> Ignoring the following files containing 000000074 events
ft930701_1244_0420G204170L.fits-> Ignoring the following files containing 000000018 events
ft930701_1244_0420G204870M.fits-> Ignoring the following files containing 000000016 events
ft930701_1244_0420G205570H.fits-> Ignoring the following files containing 000000015 events
ft930701_1244_0420G205370H.fits-> Ignoring the following files containing 000000014 events
ft930701_1244_0420G205470H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g300270h.prelist merge count = 12 photon cnt = 217108 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 22 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g300170l.prelist merge count = 4 photon cnt = 115 GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 72 GISSORTSPLIT:LO:g300370l.prelist merge count = 1 photon cnt = 89 GISSORTSPLIT:LO:g300470l.prelist merge count = 1 photon cnt = 433 GISSORTSPLIT:LO:g300570l.prelist merge count = 10 photon cnt = 25602 GISSORTSPLIT:LO:g300670l.prelist merge count = 2 photon cnt = 523 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g300270m.prelist merge count = 14 photon cnt = 121698 GISSORTSPLIT:LO:g300370m.prelist merge count = 2 photon cnt = 377 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 160 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 112 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 137 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 135 GISSORTSPLIT:LO:Total filenames split = 56 GISSORTSPLIT:LO:Total split file cnt = 18 GISSORTSPLIT:LO:End program-> Creating ad40020000g300370h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G300170H.fits 2 -- ft930701_1244_0420G300970H.fits 3 -- ft930701_1244_0420G302370H.fits 4 -- ft930701_1244_0420G302770H.fits 5 -- ft930701_1244_0420G303570H.fits 6 -- ft930701_1244_0420G303970H.fits 7 -- ft930701_1244_0420G304270H.fits 8 -- ft930701_1244_0420G304670H.fits 9 -- ft930701_1244_0420G304870H.fits 10 -- ft930701_1244_0420G305870H.fits 11 -- ft930701_1244_0420G306070H.fits 12 -- ft930701_1244_0420G306670H.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G300170H.fits 2 -- ft930701_1244_0420G300970H.fits 3 -- ft930701_1244_0420G302370H.fits 4 -- ft930701_1244_0420G302770H.fits 5 -- ft930701_1244_0420G303570H.fits 6 -- ft930701_1244_0420G303970H.fits 7 -- ft930701_1244_0420G304270H.fits 8 -- ft930701_1244_0420G304670H.fits 9 -- ft930701_1244_0420G304870H.fits 10 -- ft930701_1244_0420G305870H.fits 11 -- ft930701_1244_0420G306070H.fits 12 -- ft930701_1244_0420G306670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g300470m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G300270M.fits 2 -- ft930701_1244_0420G300870M.fits 3 -- ft930701_1244_0420G301070M.fits 4 -- ft930701_1244_0420G301970M.fits 5 -- ft930701_1244_0420G302670M.fits 6 -- ft930701_1244_0420G302870M.fits 7 -- ft930701_1244_0420G303470M.fits 8 -- ft930701_1244_0420G303670M.fits 9 -- ft930701_1244_0420G303870M.fits 10 -- ft930701_1244_0420G304070M.fits 11 -- ft930701_1244_0420G304770M.fits 12 -- ft930701_1244_0420G304970M.fits 13 -- ft930701_1244_0420G305970M.fits 14 -- ft930701_1244_0420G306570M.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G300270M.fits 2 -- ft930701_1244_0420G300870M.fits 3 -- ft930701_1244_0420G301070M.fits 4 -- ft930701_1244_0420G301970M.fits 5 -- ft930701_1244_0420G302670M.fits 6 -- ft930701_1244_0420G302870M.fits 7 -- ft930701_1244_0420G303470M.fits 8 -- ft930701_1244_0420G303670M.fits 9 -- ft930701_1244_0420G303870M.fits 10 -- ft930701_1244_0420G304070M.fits 11 -- ft930701_1244_0420G304770M.fits 12 -- ft930701_1244_0420G304970M.fits 13 -- ft930701_1244_0420G305970M.fits 14 -- ft930701_1244_0420G306570M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g300570l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G300770L.fits 2 -- ft930701_1244_0420G301570L.fits 3 -- ft930701_1244_0420G302070L.fits 4 -- ft930701_1244_0420G302570L.fits 5 -- ft930701_1244_0420G303070L.fits 6 -- ft930701_1244_0420G303770L.fits 7 -- ft930701_1244_0420G304170L.fits 8 -- ft930701_1244_0420G304570L.fits 9 -- ft930701_1244_0420G305470L.fits 10 -- ft930701_1244_0420G306470L.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G300770L.fits 2 -- ft930701_1244_0420G301570L.fits 3 -- ft930701_1244_0420G302070L.fits 4 -- ft930701_1244_0420G302570L.fits 5 -- ft930701_1244_0420G303070L.fits 6 -- ft930701_1244_0420G303770L.fits 7 -- ft930701_1244_0420G304170L.fits 8 -- ft930701_1244_0420G304570L.fits 9 -- ft930701_1244_0420G305470L.fits 10 -- ft930701_1244_0420G306470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000g300670l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420G302470L.fits 2 -- ft930701_1244_0420G302970L.fits Merging binary extension #: 2 1 -- ft930701_1244_0420G302470L.fits 2 -- ft930701_1244_0420G302970L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000433 events
ft930701_1244_0420G302170L.fits-> Ignoring the following files containing 000000377 events
ft930701_1244_0420G301870M.fits ft930701_1244_0420G303370M.fits-> Ignoring the following files containing 000000160 events
ft930701_1244_0420G303170M.fits-> Ignoring the following files containing 000000137 events
ft930701_1244_0420G301670M.fits-> Ignoring the following files containing 000000135 events
ft930701_1244_0420G301770M.fits-> Ignoring the following files containing 000000115 events
ft930701_1244_0420G301470L.fits ft930701_1244_0420G304470L.fits ft930701_1244_0420G305370L.fits ft930701_1244_0420G306370L.fits-> Ignoring the following files containing 000000112 events
ft930701_1244_0420G303270M.fits-> Ignoring the following files containing 000000089 events
ft930701_1244_0420G300670L.fits-> Ignoring the following files containing 000000072 events
ft930701_1244_0420G304370L.fits-> Ignoring the following files containing 000000022 events
ft930701_1244_0420G305570H.fits-> Ignoring the following files containing 000000020 events
ft930701_1244_0420G305070M.fits-> Ignoring the following files containing 000000020 events
ft930701_1244_0420G302270H.fits-> Ignoring the following files containing 000000019 events
ft930701_1244_0420G305770H.fits-> Ignoring the following files containing 000000009 events
ft930701_1244_0420G305670H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000102h.prelist merge count = 13 photon cnt = 175921 SIS0SORTSPLIT:LO:s000202l.prelist merge count = 11 photon cnt = 24817 SIS0SORTSPLIT:LO:s000302l.prelist merge count = 2 photon cnt = 125 SIS0SORTSPLIT:LO:s000402m.prelist merge count = 13 photon cnt = 105355 SIS0SORTSPLIT:LO:s000502m.prelist merge count = 4 photon cnt = 138 SIS0SORTSPLIT:LO:Total filenames split = 43 SIS0SORTSPLIT:LO:Total split file cnt = 5 SIS0SORTSPLIT:LO:End program-> Creating ad40020000s000402h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S000102H.fits 2 -- ft930701_1244_0420S000702H.fits 3 -- ft930701_1244_0420S001302H.fits 4 -- ft930701_1244_0420S001602H.fits 5 -- ft930701_1244_0420S002202H.fits 6 -- ft930701_1244_0420S002902H.fits 7 -- ft930701_1244_0420S003502H.fits 8 -- ft930701_1244_0420S003702H.fits 9 -- ft930701_1244_0420S003902H.fits 10 -- ft930701_1244_0420S004102H.fits 11 -- ft930701_1244_0420S004702H.fits 12 -- ft930701_1244_0420S004902H.fits 13 -- ft930701_1244_0420S005402H.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S000102H.fits 2 -- ft930701_1244_0420S000702H.fits 3 -- ft930701_1244_0420S001302H.fits 4 -- ft930701_1244_0420S001602H.fits 5 -- ft930701_1244_0420S002202H.fits 6 -- ft930701_1244_0420S002902H.fits 7 -- ft930701_1244_0420S003502H.fits 8 -- ft930701_1244_0420S003702H.fits 9 -- ft930701_1244_0420S003902H.fits 10 -- ft930701_1244_0420S004102H.fits 11 -- ft930701_1244_0420S004702H.fits 12 -- ft930701_1244_0420S004902H.fits 13 -- ft930701_1244_0420S005402H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s000502m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S000202M.fits 2 -- ft930701_1244_0420S000602M.fits 3 -- ft930701_1244_0420S000802M.fits 4 -- ft930701_1244_0420S001102M.fits 5 -- ft930701_1244_0420S001502M.fits 6 -- ft930701_1244_0420S001702M.fits 7 -- ft930701_1244_0420S001902M.fits 8 -- ft930701_1244_0420S002102M.fits 9 -- ft930701_1244_0420S002302M.fits 10 -- ft930701_1244_0420S002802M.fits 11 -- ft930701_1244_0420S003002M.fits 12 -- ft930701_1244_0420S003802M.fits 13 -- ft930701_1244_0420S004202M.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S000202M.fits 2 -- ft930701_1244_0420S000602M.fits 3 -- ft930701_1244_0420S000802M.fits 4 -- ft930701_1244_0420S001102M.fits 5 -- ft930701_1244_0420S001502M.fits 6 -- ft930701_1244_0420S001702M.fits 7 -- ft930701_1244_0420S001902M.fits 8 -- ft930701_1244_0420S002102M.fits 9 -- ft930701_1244_0420S002302M.fits 10 -- ft930701_1244_0420S002802M.fits 11 -- ft930701_1244_0420S003002M.fits 12 -- ft930701_1244_0420S003802M.fits 13 -- ft930701_1244_0420S004202M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s000602l.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S000502L.fits 2 -- ft930701_1244_0420S001002L.fits 3 -- ft930701_1244_0420S001202L.fits 4 -- ft930701_1244_0420S001402L.fits 5 -- ft930701_1244_0420S002002L.fits 6 -- ft930701_1244_0420S002602L.fits 7 -- ft930701_1244_0420S003602L.fits 8 -- ft930701_1244_0420S004402L.fits 9 -- ft930701_1244_0420S004602L.fits 10 -- ft930701_1244_0420S005002L.fits 11 -- ft930701_1244_0420S005202L.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S000502L.fits 2 -- ft930701_1244_0420S001002L.fits 3 -- ft930701_1244_0420S001202L.fits 4 -- ft930701_1244_0420S001402L.fits 5 -- ft930701_1244_0420S002002L.fits 6 -- ft930701_1244_0420S002602L.fits 7 -- ft930701_1244_0420S003602L.fits 8 -- ft930701_1244_0420S004402L.fits 9 -- ft930701_1244_0420S004602L.fits 10 -- ft930701_1244_0420S005002L.fits 11 -- ft930701_1244_0420S005202L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000138 events
ft930701_1244_0420S000302M.fits ft930701_1244_0420S001802M.fits ft930701_1244_0420S002402M.fits ft930701_1244_0420S002702M.fits-> Ignoring the following files containing 000000125 events
ft930701_1244_0420S004502L.fits ft930701_1244_0420S005102L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100102h.prelist merge count = 13 photon cnt = 171318 SIS1SORTSPLIT:LO:s100202l.prelist merge count = 12 photon cnt = 30120 SIS1SORTSPLIT:LO:s100302l.prelist merge count = 2 photon cnt = 64 SIS1SORTSPLIT:LO:s100402m.prelist merge count = 15 photon cnt = 104497 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 4 photon cnt = 153 SIS1SORTSPLIT:LO:Total filenames split = 46 SIS1SORTSPLIT:LO:Total split file cnt = 5 SIS1SORTSPLIT:LO:End program-> Creating ad40020000s100402h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S100102H.fits 2 -- ft930701_1244_0420S100702H.fits 3 -- ft930701_1244_0420S101302H.fits 4 -- ft930701_1244_0420S101602H.fits 5 -- ft930701_1244_0420S102202H.fits 6 -- ft930701_1244_0420S102902H.fits 7 -- ft930701_1244_0420S103502H.fits 8 -- ft930701_1244_0420S103702H.fits 9 -- ft930701_1244_0420S103902H.fits 10 -- ft930701_1244_0420S104102H.fits 11 -- ft930701_1244_0420S104702H.fits 12 -- ft930701_1244_0420S104902H.fits 13 -- ft930701_1244_0420S105402H.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S100102H.fits 2 -- ft930701_1244_0420S100702H.fits 3 -- ft930701_1244_0420S101302H.fits 4 -- ft930701_1244_0420S101602H.fits 5 -- ft930701_1244_0420S102202H.fits 6 -- ft930701_1244_0420S102902H.fits 7 -- ft930701_1244_0420S103502H.fits 8 -- ft930701_1244_0420S103702H.fits 9 -- ft930701_1244_0420S103902H.fits 10 -- ft930701_1244_0420S104102H.fits 11 -- ft930701_1244_0420S104702H.fits 12 -- ft930701_1244_0420S104902H.fits 13 -- ft930701_1244_0420S105402H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s100502m.unf
---- cmerge: version 1.5 ---- A total of 15 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S100202M.fits 2 -- ft930701_1244_0420S100602M.fits 3 -- ft930701_1244_0420S100802M.fits 4 -- ft930701_1244_0420S101102M.fits 5 -- ft930701_1244_0420S101502M.fits 6 -- ft930701_1244_0420S101702M.fits 7 -- ft930701_1244_0420S101902M.fits 8 -- ft930701_1244_0420S102102M.fits 9 -- ft930701_1244_0420S102302M.fits 10 -- ft930701_1244_0420S102802M.fits 11 -- ft930701_1244_0420S103002M.fits 12 -- ft930701_1244_0420S103802M.fits 13 -- ft930701_1244_0420S104202M.fits 14 -- ft930701_1244_0420S104802M.fits 15 -- ft930701_1244_0420S105302M.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S100202M.fits 2 -- ft930701_1244_0420S100602M.fits 3 -- ft930701_1244_0420S100802M.fits 4 -- ft930701_1244_0420S101102M.fits 5 -- ft930701_1244_0420S101502M.fits 6 -- ft930701_1244_0420S101702M.fits 7 -- ft930701_1244_0420S101902M.fits 8 -- ft930701_1244_0420S102102M.fits 9 -- ft930701_1244_0420S102302M.fits 10 -- ft930701_1244_0420S102802M.fits 11 -- ft930701_1244_0420S103002M.fits 12 -- ft930701_1244_0420S103802M.fits 13 -- ft930701_1244_0420S104202M.fits 14 -- ft930701_1244_0420S104802M.fits 15 -- ft930701_1244_0420S105302M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad40020000s100602l.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930701_1244_0420S100502L.fits 2 -- ft930701_1244_0420S101002L.fits 3 -- ft930701_1244_0420S101202L.fits 4 -- ft930701_1244_0420S101402L.fits 5 -- ft930701_1244_0420S102002L.fits 6 -- ft930701_1244_0420S102602L.fits 7 -- ft930701_1244_0420S103302L.fits 8 -- ft930701_1244_0420S103602L.fits 9 -- ft930701_1244_0420S104402L.fits 10 -- ft930701_1244_0420S104602L.fits 11 -- ft930701_1244_0420S105002L.fits 12 -- ft930701_1244_0420S105202L.fits Merging binary extension #: 2 1 -- ft930701_1244_0420S100502L.fits 2 -- ft930701_1244_0420S101002L.fits 3 -- ft930701_1244_0420S101202L.fits 4 -- ft930701_1244_0420S101402L.fits 5 -- ft930701_1244_0420S102002L.fits 6 -- ft930701_1244_0420S102602L.fits 7 -- ft930701_1244_0420S103302L.fits 8 -- ft930701_1244_0420S103602L.fits 9 -- ft930701_1244_0420S104402L.fits 10 -- ft930701_1244_0420S104602L.fits 11 -- ft930701_1244_0420S105002L.fits 12 -- ft930701_1244_0420S105202L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000153 events
ft930701_1244_0420S100302M.fits ft930701_1244_0420S101802M.fits ft930701_1244_0420S102402M.fits ft930701_1244_0420S102702M.fits-> Ignoring the following files containing 000000064 events
ft930701_1244_0420S104502L.fits ft930701_1244_0420S105102L.fits-> Tar-ing together the leftover raw files
a ft930701_0242_1244G200370H.fits 40K a ft930701_0242_1244G200870L.fits 40K a ft930701_0242_1244G201170H.fits 40K a ft930701_0242_1244G201870H.fits 40K a ft930701_0242_1244G201970H.fits 40K a ft930701_0242_1244G202070H.fits 40K a ft930701_0242_1244G203270H.fits 40K a ft930701_0242_1244G203370H.fits 40K a ft930701_0242_1244G203470H.fits 40K a ft930701_0242_1244G203670H.fits 40K a ft930701_0242_1244G204370L.fits 40K a ft930701_0242_1244G204870L.fits 40K a ft930701_0242_1244G205670H.fits 40K a ft930701_0242_1244G300370H.fits 40K a ft930701_0242_1244G300870L.fits 40K a ft930701_0242_1244G301170H.fits 40K a ft930701_0242_1244G301970H.fits 40K a ft930701_0242_1244G302070H.fits 40K a ft930701_0242_1244G303370H.fits 40K a ft930701_0242_1244G303470H.fits 40K a ft930701_0242_1244G304170L.fits 40K a ft930701_0242_1244G304670L.fits 40K a ft930701_0242_1244G305370H.fits 40K a ft930701_0242_1244G305470H.fits 40K a ft930701_0242_1244S000902L.fits 40K a ft930701_0242_1244S001402L.fits 40K a ft930701_0242_1244S002602L.fits 40K a ft930701_0242_1244S003302H.fits 40K a ft930701_0242_1244S100902L.fits 40K a ft930701_0242_1244S101402L.fits 40K a ft930701_0242_1244S102602L.fits 40K a ft930701_0242_1244S103302H.fits 40K a ft930701_1244_0420G200670L.fits 40K a ft930701_1244_0420G201470L.fits 40K a ft930701_1244_0420G201670M.fits 43K a ft930701_1244_0420G201770M.fits 43K a ft930701_1244_0420G201870M.fits 43K a ft930701_1244_0420G202270L.fits 45K a ft930701_1244_0420G202770L.fits 45K a ft930701_1244_0420G202970M.fits 43K a ft930701_1244_0420G203070M.fits 40K a ft930701_1244_0420G203170M.fits 43K a ft930701_1244_0420G204170L.fits 40K a ft930701_1244_0420G204270L.fits 40K a ft930701_1244_0420G204870M.fits 40K a ft930701_1244_0420G205170L.fits 40K a ft930701_1244_0420G205370H.fits 40K a ft930701_1244_0420G205470H.fits 40K a ft930701_1244_0420G205570H.fits 40K a ft930701_1244_0420G206070L.fits 40K a ft930701_1244_0420G300670L.fits 40K a ft930701_1244_0420G301470L.fits 40K a ft930701_1244_0420G301670M.fits 43K a ft930701_1244_0420G301770M.fits 43K a ft930701_1244_0420G301870M.fits 45K a ft930701_1244_0420G302170L.fits 51K a ft930701_1244_0420G302270H.fits 40K a ft930701_1244_0420G303170M.fits 43K a ft930701_1244_0420G303270M.fits 43K a ft930701_1244_0420G303370M.fits 43K a ft930701_1244_0420G304370L.fits 40K a ft930701_1244_0420G304470L.fits 40K a ft930701_1244_0420G305070M.fits 40K a ft930701_1244_0420G305370L.fits 40K a ft930701_1244_0420G305570H.fits 40K a ft930701_1244_0420G305670H.fits 40K a ft930701_1244_0420G305770H.fits 40K a ft930701_1244_0420G306370L.fits 40K a ft930701_1244_0420S000302M.fits 40K a ft930701_1244_0420S001802M.fits 40K a ft930701_1244_0420S002402M.fits 40K a ft930701_1244_0420S002702M.fits 40K a ft930701_1244_0420S004502L.fits 40K a ft930701_1244_0420S005102L.fits 40K a ft930701_1244_0420S100302M.fits 40K a ft930701_1244_0420S101802M.fits 40K a ft930701_1244_0420S102402M.fits 40K a ft930701_1244_0420S102702M.fits 40K a ft930701_1244_0420S104502L.fits 40K a ft930701_1244_0420S105102L.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft930701_0242.1244 'ft930701_0242.1244' is successfully opened Data Start Time is 15648132.36 (930701 024212) Time Margin 2.0 sec included Sync error detected in 6787 th SF Sync error detected in 8477 th SF Sync error detected in 11015 th SF 'ft930701_0242.1244' EOF detected, sf=11048 Data End Time is 15684274.24 (930701 124434) Gain History is written in ft930701_0242_1244.ghf-> Checking if column CAL_START in ft930701_0242_1244.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft930701_0242_1244.ghf[1] is in order
Time column is TIME ORDERED-> Creating gain history file ft930701_1244_0420.ghf
temp2gain v4.2 opening ft930701_1244.0420 'ft930701_1244.0420' is successfully opened Data Start Time is 15684344.24 (930701 124544) Time Margin 2.0 sec included 'ft930701_1244.0420' EOF detected, sf=11088 Data End Time is 15740444.07 (930702 042044) Gain History is written in ft930701_1244_0420.ghf-> Checking if column CAL_START in ft930701_1244_0420.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft930701_1244_0420.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad40020000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g200370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g200470m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g200570l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300470m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300570l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000g300670l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000202l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000402h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000502m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s000602l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100202l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100402h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100502m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad40020000s100602l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 93/ 7/ 1 2:42 mjd=49169.112500 Orbit file name is ./frf.orbit.201 Epoch of Orbital Elements: 1993/6/28 12:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa930701_0242.1244 S0-HK file: ft930701_0242_1244S0HK.fits S1-HK file: ft930701_0242_1244S1HK.fits G2-HK file: ft930701_0242_1244G2HK.fits G3-HK file: ft930701_0242_1244G3HK.fits output FITS File: ft930701_0242_1244.mkf Total 1130 Data bins were processed.-> Checking if column TIME in ft930701_0242_1244.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
Date and time are: 93/ 7/ 1 12:44 mjd=49169.530556 Orbit file name is ./frf.orbit.201 Epoch of Orbital Elements: 1993/6/28 12:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa930701_1244.0420 S0-HK file: ft930701_1244_0420S0HK.fits S1-HK file: ft930701_1244_0420S1HK.fits G2-HK file: ft930701_1244_0420G2HK.fits G3-HK file: ft930701_1244_0420G3HK.fits output FITS File: ft930701_1244_0420.mkf Total 1756 Data bins were processed.-> Checking if column TIME in ft930701_1244_0420.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 12295.385 The mean of the selected column is 39.282381 The standard deviation of the selected column is 9.7838005 The minimum of selected column is 10.916700 The maximum of selected column is 77.406487 The number of points used in calculation is 313-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>9.9 && S0_PIXL1<68.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.20E+05 135344 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
134535 102668 0 31867 0 0
Writing events file
102668 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
134535 102668 0 31867 0 0
in 10195.39 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 102668
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 1 2275
Flickering pixels iter, pixels & cnts : 1 15 270
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 16
Number of (internal) image counts : 102668
Number of image cts rejected (N, %) : 2545 2.4788640
By chip : 0 1 2 3
Pixels rejected : 0 16 0 0
Image counts : 0 102668 0 0
Image cts rejected: 0 2545 0 0
Image cts rej (%) : 0.00 2.48 0.00 0.00
filtering data...
Total counts : 0 102668 0 0
Total cts rejected: 0 2545 0 0
Total cts rej (%) : 0.00 2.48 0.00 0.00
Number of clean counts accepted : 100123
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 16
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000102h.evt use_events=no
Wrote cleaned events file to ad40020000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad40020000s000202l.unf into ad40020000s000202l.evtThe sum of the selected column is 1399.6614 The mean of the selected column is 93.310758 The standard deviation of the selected column is 60.835722 The minimum of selected column is 28.093750 The maximum of selected column is 232.18906 The number of points used in calculation is 15-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<275.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.23E+04 14091 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13971 3647 0 10324 0 0
Writing events file
3647 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13971 3647 0 10324 0 0
in 480.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3647
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 1 109
Flickering pixels iter, pixels & cnts : 1 4 14
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 5
Number of (internal) image counts : 3647
Number of image cts rejected (N, %) : 123 3.3726351
By chip : 0 1 2 3
Pixels rejected : 0 5 0 0
Image counts : 0 3647 0 0
Image cts rejected: 0 123 0 0
Image cts rej (%) : 0.00 3.37 0.00 0.00
filtering data...
Total counts : 0 3647 0 0
Total cts rejected: 0 123 0 0
Total cts rej (%) : 0.00 3.37 0.00 0.00
Number of clean counts accepted : 3524
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000202l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000202l.evt use_events=no
Wrote cleaned events file to ad40020000s000202l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad40020000s000302m.unf into ad40020000s000302m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 02:42:20 0.20E+03 1196 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000302m.evt use_events=no
Wrote cleaned events file to ad40020000s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad40020000s000302m.evt since it contains 0 eventsThe sum of the selected column is 14961.732 The mean of the selected column is 39.166838 The standard deviation of the selected column is 10.081395 The minimum of selected column is 8.7503061 The maximum of selected column is 100.46906 The number of points used in calculation is 382-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>8.9 && S0_PIXL1<69.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.19E+05 175921 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
174866 128395 0 46471 0 0
Writing events file
128395 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
174866 128395 0 46471 0 0
in 12523.44 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 128395
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 1 2750
Flickering pixels iter, pixels & cnts : 1 18 336
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 19
Number of (internal) image counts : 128395
Number of image cts rejected (N, %) : 3086 2.4035203
By chip : 0 1 2 3
Pixels rejected : 0 19 0 0
Image counts : 0 128395 0 0
Image cts rejected: 0 3086 0 0
Image cts rej (%) : 0.00 2.40 0.00 0.00
filtering data...
Total counts : 0 128395 0 0
Total cts rejected: 0 3086 0 0
Total cts rej (%) : 0.00 2.40 0.00 0.00
Number of clean counts accepted : 125309
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 19
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000402h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000402h.evt use_events=no
Wrote cleaned events file to ad40020000s000402h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad40020000s000502m.unf into ad40020000s000502m.evtThe sum of the selected column is 7472.3041 The mean of the selected column is 43.443628 The standard deviation of the selected column is 12.260585 The minimum of selected column is 21.312565 The maximum of selected column is 86.031509 The number of points used in calculation is 172-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>6.6 && S0_PIXL1<80.2 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.12E+05 105355 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
104747 70772 0 33975 0 0
Writing events file
70772 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
104747 70772 0 33975 0 0
in 7163.34 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 70772
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 1 1588
Flickering pixels iter, pixels & cnts : 1 21 231
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 22
Number of (internal) image counts : 70772
Number of image cts rejected (N, %) : 1819 2.5702255
By chip : 0 1 2 3
Pixels rejected : 0 22 0 0
Image counts : 0 70772 0 0
Image cts rejected: 0 1819 0 0
Image cts rej (%) : 0.00 2.57 0.00 0.00
filtering data...
Total counts : 0 70772 0 0
Total cts rejected: 0 1819 0 0
Total cts rej (%) : 0.00 2.57 0.00 0.00
Number of clean counts accepted : 68953
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 22
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000502m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000502m.evt use_events=no
Wrote cleaned events file to ad40020000s000502m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad40020000s000602l.unf into ad40020000s000602l.evtThe sum of the selected column is 734.12761 The mean of the selected column is 56.471355 The standard deviation of the selected column is 25.234639 The minimum of selected column is 20.031372 The maximum of selected column is 100.87560 The number of points used in calculation is 13-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<132.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.13E+05 24817 0100
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
24551 3548 0 21003 0 0
Writing events file
3548 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24551 3548 0 21003 0 0
in 480.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3548
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 1 104
Flickering pixels iter, pixels & cnts : 1 4 17
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 5
Number of (internal) image counts : 3548
Number of image cts rejected (N, %) : 121 3.4103720
By chip : 0 1 2 3
Pixels rejected : 0 5 0 0
Image counts : 0 3548 0 0
Image cts rejected: 0 121 0 0
Image cts rej (%) : 0.00 3.41 0.00 0.00
filtering data...
Total counts : 0 3548 0 0
Total cts rejected: 0 121 0 0
Total cts rej (%) : 0.00 3.41 0.00 0.00
Number of clean counts accepted : 3427
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s000602l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad40020000s000602l.evt use_events=no
Wrote cleaned events file to ad40020000s000602l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad40020000s100102h.unf into ad40020000s100102h.evtThe sum of the selected column is 16298.140 The mean of the selected column is 52.070734 The standard deviation of the selected column is 18.526680 The minimum of selected column is 10.828193 The maximum of selected column is 184.53186 The number of points used in calculation is 313-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<107.6 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.21E+05 133634 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
132401 97805 0 34596 0 0
Writing events file
97805 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
132401 97805 0 34596 0 0
in 10181.49 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 97805
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 8 15803
Flickering pixels iter, pixels & cnts : 1 16 72
Number of pixels rejected : 24
Number of (internal) image counts : 97805
Number of image cts rejected (N, %) : 15875 16.2312775
By chip : 0 1 2 3
Pixels rejected : 0 0 0 24
Image counts : 0 0 0 97805
Image cts rejected: 0 0 0 15875
Image cts rej (%) : 0.00 0.00 0.00 16.23
filtering data...
Total counts : 0 0 0 97805
Total cts rejected: 0 0 0 15875
Total cts rej (%) : 0.00 0.00 0.00 16.23
Number of clean counts accepted : 81930
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 24
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100102h.evt use_events=no
Wrote cleaned events file to ad40020000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad40020000s100202l.unf into ad40020000s100202l.evtThe sum of the selected column is 1840.7869 The mean of the selected column is 153.39891 The standard deviation of the selected column is 128.52483 The minimum of selected column is 33.218750 The maximum of selected column is 407.00275 The number of points used in calculation is 12-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<538.9 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.27E+04 15058 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
14853 2913 0 11940 0 0
Writing events file
2913 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14853 2913 0 11940 0 0
in 384.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 2913
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 6 389
Flickering pixels iter, pixels & cnts : 1 4 21
Number of pixels rejected : 10
Number of (internal) image counts : 2913
Number of image cts rejected (N, %) : 410 14.0748367
By chip : 0 1 2 3
Pixels rejected : 0 0 0 10
Image counts : 0 0 0 2913
Image cts rejected: 0 0 0 410
Image cts rej (%) : 0.00 0.00 0.00 14.07
filtering data...
Total counts : 0 0 0 2913
Total cts rejected: 0 0 0 410
Total cts rej (%) : 0.00 0.00 0.00 14.07
Number of clean counts accepted : 2503
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100202l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100202l.evt use_events=no
Wrote cleaned events file to ad40020000s100202l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad40020000s100302m.unf into ad40020000s100302m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 02:42:20 0.97E+03 1774 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100302m.evt use_events=no
Wrote cleaned events file to ad40020000s100302m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad40020000s100302m.evt since it contains 0 eventsThe sum of the selected column is 19928.986 The mean of the selected column is 52.170119 The standard deviation of the selected column is 18.508208 The minimum of selected column is 22.843821 The maximum of selected column is 183.93806 The number of points used in calculation is 382-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<107.6 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.19E+05 171318 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
170027 123606 0 46421 0 0
Writing events file
123606 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
170027 123606 0 46421 0 0
in 12487.48 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 123606
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 19016
Flickering pixels iter, pixels & cnts : 1 18 295
Number of pixels rejected : 25
Number of (internal) image counts : 123606
Number of image cts rejected (N, %) : 19311 15.6230278
By chip : 0 1 2 3
Pixels rejected : 0 0 0 25
Image counts : 0 0 0 123606
Image cts rejected: 0 0 0 19311
Image cts rej (%) : 0.00 0.00 0.00 15.62
filtering data...
Total counts : 0 0 0 123606
Total cts rejected: 0 0 0 19311
Total cts rej (%) : 0.00 0.00 0.00 15.62
Number of clean counts accepted : 104295
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 25
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100402h.evt use_events=no
Wrote cleaned events file to ad40020000s100402h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad40020000s100502m.unf into ad40020000s100502m.evtThe sum of the selected column is 9985.4992 The mean of the selected column is 58.055228 The standard deviation of the selected column is 21.154544 The minimum of selected column is 23.312571 The maximum of selected column is 185.68806 The number of points used in calculation is 172-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<121.5 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.13E+05 104497 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
103471 68861 0 34610 0 0
Writing events file
68861 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
103471 68861 0 34610 0 0
in 7137.73 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 68861
Total counts in chip images : 68860
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 10886
Flickering pixels iter, pixels & cnts : 1 19 238
Number of pixels rejected : 26
Number of (internal) image counts : 68860
Number of image cts rejected (N, %) : 11124 16.1545162
By chip : 0 1 2 3
Pixels rejected : 0 0 0 26
Image counts : 0 0 0 68860
Image cts rejected: 0 0 0 11124
Image cts rej (%) : 0.00 0.00 0.00 16.15
filtering data...
Total counts : 0 0 0 68861
Total cts rejected: 0 0 0 11125
Total cts rej (%) : 0.00 0.00 0.00 16.16
Number of clean counts accepted : 57736
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100502m.evt use_events=no
Wrote cleaned events file to ad40020000s100502m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad40020000s100602l.unf into ad40020000s100602l.evtThe sum of the selected column is 714.37558 The mean of the selected column is 59.531299 The standard deviation of the selected column is 20.914559 The minimum of selected column is 34.906250 The maximum of selected column is 94.968750 The number of points used in calculation is 12-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<122.2 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.15E+05 30120 0001
Processing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
29036 3403 0 25633 0 0
Writing events file
3403 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29036 3403 0 25633 0 0
in 448.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/40020000.013/screen_in_event.xsl
reading data file: /data/data24/seq_proc/40020000.013/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3403
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 6 440
Flickering pixels iter, pixels & cnts : 1 5 27
Number of pixels rejected : 11
Number of (internal) image counts : 3403
Number of image cts rejected (N, %) : 467 13.7231855
By chip : 0 1 2 3
Pixels rejected : 0 0 0 11
Image counts : 0 0 0 3403
Image cts rejected: 0 0 0 467
Image cts rej (%) : 0.00 0.00 0.00 13.72
filtering data...
Total counts : 0 0 0 3403
Total cts rejected: 0 0 0 467
Total cts rej (%) : 0.00 0.00 0.00 13.72
Number of clean counts accepted : 2936
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000s100602l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad40020000s100602l.evt use_events=no
Wrote cleaned events file to ad40020000s100602l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad40020000g200170h.unf into ad40020000g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.unf
Total Good Bad: Region Time Phase Cut
139026 85010 15969 38047 0 0
Writing events file
85010 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
139026 85010 15969 38047 0 0
in 9793.84 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
85010 83335 1675
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad40020000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 83335 in ad40020000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/40020000.013/ad40020000g200270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad40020000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad40020000g200270m.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.unf
Total Good Bad: Region Time Phase Cut
172938 130005 16388 26545 0 0
Writing events file
130005 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172938 130005 16388 26545 0 0
in 14233.62 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
130005 127437 2568
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad40020000g200370h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 127437 in ad40020000g200370h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 100097 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.unf
Total Good Bad: Region Time Phase Cut
100097 72893 10799 16405 0 0
Writing events file
72893 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100097 72893 10799 16405 0 0
in 8479.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
72893 71395 1498
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad40020000g200470m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 71395 in ad40020000g200470m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 26016 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.unf
Total Good Bad: Region Time Phase Cut
26016 339 9610 16067 0 0
Writing events file
339 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26016 339 9610 16067 0 0
in 96.16 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
339 329 10
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad40020000g200570l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 329 in ad40020000g200570l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.unf
Total Good Bad: Region Time Phase Cut
167616 111096 13991 42529 0 0
Writing events file
111096 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
167616 111096 13991 42529 0 0
in 9793.84 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
111096 109209 1887
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 109209 in ad40020000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/40020000.013/ad40020000g300270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad40020000g300270m.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.unf
Total Good Bad: Region Time Phase Cut
217108 169813 14120 33175 0 0
Writing events file
169813 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
217108 169813 14120 33175 0 0
in 14231.62 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
169813 166915 2898
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300370h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 166915 in ad40020000g300370h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.unf
Total Good Bad: Region Time Phase Cut
121698 92560 9377 19761 0 0
Writing events file
92560 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
121698 92560 9377 19761 0 0
in 8479.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
92560 90895 1665
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300470m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 90895 in ad40020000g300470m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 25602 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.unf
Total Good Bad: Region Time Phase Cut
25602 358 8523 16721 0 0
Writing events file
358 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25602 358 8523 16721 0 0
in 96.16 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
358 350 8
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300570l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300570l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 350 in ad40020000g300570l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 18:10:14 0.26E+03 523 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/40020000.013/ad40020000g300670l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!screen:ASCA > read events ad40020000g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad40020000g300670l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad40020000g300670l.evt since it contains 0 events-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad40020000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9978
Mean RA/DEC/ROLL : 308.0528 37.7504 326.9978
Pnt RA/DEC/ROLL : 308.0328 37.4936 326.9978
Image rebin factor : 1
Attitude Records : 44031
GTI intervals : 23
Total GTI (secs) : 9793.837
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1213.9913330 1213.9913330
20 Percent Complete: Total/live time: 2180.9267578 2180.9267578
30 Percent Complete: Total/live time: 3104.4238281 3104.4238281
40 Percent Complete: Total/live time: 4101.8403320 4101.8403320
50 Percent Complete: Total/live time: 5068.8374023 5068.8374023
60 Percent Complete: Total/live time: 6975.2343750 6975.2343750
70 Percent Complete: Total/live time: 6975.2343750 6975.2343750
80 Percent Complete: Total/live time: 7962.7314453 7962.7314453
90 Percent Complete: Total/live time: 9540.2177734 9540.2177734
100 Percent Complete: Total/live time: 9793.8369141 9793.8369141
Number of attitude steps used: 47
Number of attitude steps avail: 27841
Mean RA/DEC pixel offset: -12.2207 -2.2891
writing expo file: ad40020000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 83180 155 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83335 83180 155 0 0 0
in 9793.84 seconds
Image has 83180 counts for 8.493 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 10780 155 0 0 72400
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83335 10780 155 0 0 72400
in 9793.84 seconds
Image has 10780 counts for 1.101 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 72611 155 0 0 10569
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83335 72611 155 0 0 10569
in 9793.84 seconds
Image has 72611 counts for 7.414 counts/sec
Command not found; type ? for a command listing
!ad40020000g200170h:ASCA >
!ad40020000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g200170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g200170h:ASCA > read events ad40020000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g200170h:ASCA-GIS2-PH > set image sky
!ad40020000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad40020000g200170h:ASCA-GIS2-PH > extract image
!ad40020000g200170h:ASCA-GIS2-PH > save image outfile=ad40020000g200170h.img
Wrote image to file ad40020000g200170h.img
!ad40020000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad40020000g200170h:ASCA-GIS2-PH > extract image
!ad40020000g200170h:ASCA-GIS2-PH > save image outfile=ad40020000g200170h_lo.img
Wrote image to file ad40020000g200170h_lo.img
!ad40020000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad40020000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g200170h:ASCA-GIS2-PH > extract image
!ad40020000g200170h:ASCA-GIS2-PH > save image outfile=ad40020000g200170h_hi.img
Wrote image to file ad40020000g200170h_hi.img
!ad40020000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad40020000g200370h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g200370h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 327.0046
Mean RA/DEC/ROLL : 308.0588 37.7265 327.0046
Pnt RA/DEC/ROLL : 308.0121 37.7641 327.0046
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 18
Total GTI (secs) : 14233.618
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2059.9936523 2059.9936523
20 Percent Complete: Total/live time: 3263.4902344 3263.4902344
30 Percent Complete: Total/live time: 5455.0434570 5455.0434570
40 Percent Complete: Total/live time: 6043.0419922 6043.0419922
50 Percent Complete: Total/live time: 7779.5371094 7779.5371094
60 Percent Complete: Total/live time: 9541.9296875 9541.9296875
70 Percent Complete: Total/live time: 10546.0361328 10546.0361328
80 Percent Complete: Total/live time: 11645.9121094 11645.9121094
90 Percent Complete: Total/live time: 12977.7753906 12977.7753906
100 Percent Complete: Total/live time: 14233.6181641 14233.6181641
Number of attitude steps used: 52
Number of attitude steps avail: 31273
Mean RA/DEC pixel offset: -13.6255 -2.9275
writing expo file: ad40020000g200370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g200370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g200370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 127179 258 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
127437 127179 258 0 0 0
in 14233.62 seconds
Image has 127179 counts for 8.935 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 16427 258 0 0 110752
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
127437 16427 258 0 0 110752
in 14233.62 seconds
Image has 16427 counts for 1.154 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 111054 258 0 0 16125
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
127437 111054 258 0 0 16125
in 14233.62 seconds
Image has 111054 counts for 7.802 counts/sec
Command not found; type ? for a command listing
!ad40020000g200370h:ASCA >
!ad40020000g200370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g200370h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g200370h:ASCA > read events ad40020000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g200370h:ASCA-GIS2-PH > set image sky
!ad40020000g200370h:ASCA-GIS2-PH > filter region corner_point.reg
!ad40020000g200370h:ASCA-GIS2-PH > extract image
!ad40020000g200370h:ASCA-GIS2-PH > save image outfile=ad40020000g200370h.img
Wrote image to file ad40020000g200370h.img
!ad40020000g200370h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad40020000g200370h:ASCA-GIS2-PH > extract image
!ad40020000g200370h:ASCA-GIS2-PH > save image outfile=ad40020000g200370h_lo.img
Wrote image to file ad40020000g200370h_lo.img
!ad40020000g200370h:ASCA-GIS2-PH > clear pha_cut
!ad40020000g200370h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g200370h:ASCA-GIS2-PH > extract image
!ad40020000g200370h:ASCA-GIS2-PH > save image outfile=ad40020000g200370h_hi.img
Wrote image to file ad40020000g200370h_hi.img
!ad40020000g200370h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad40020000g200470m.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g200470m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 327.0049
Mean RA/DEC/ROLL : 308.0589 37.7268 327.0049
Pnt RA/DEC/ROLL : 308.0119 37.7641 327.0049
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 11
Total GTI (secs) : 8479.991
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1102.9965820 1102.9965820
20 Percent Complete: Total/live time: 1966.9855957 1966.9855957
30 Percent Complete: Total/live time: 4047.0024414 4047.0024414
40 Percent Complete: Total/live time: 4047.0024414 4047.0024414
50 Percent Complete: Total/live time: 4735.0004883 4735.0004883
60 Percent Complete: Total/live time: 5178.9995117 5178.9995117
70 Percent Complete: Total/live time: 6034.9726562 6034.9726562
80 Percent Complete: Total/live time: 8048.0424805 8048.0424805
90 Percent Complete: Total/live time: 8048.0424805 8048.0424805
100 Percent Complete: Total/live time: 8479.9921875 8479.9921875
Number of attitude steps used: 53
Number of attitude steps avail: 10773
Mean RA/DEC pixel offset: -13.5668 -2.8464
writing expo file: ad40020000g200470m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g200470m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g200470m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 71270 125 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
71395 71270 125 0 0 0
in 8479.99 seconds
Image has 71270 counts for 8.404 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 9281 125 0 0 61989
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
71395 9281 125 0 0 61989
in 8479.99 seconds
Image has 9281 counts for 1.094 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 62166 125 0 0 9104
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
71395 62166 125 0 0 9104
in 8479.99 seconds
Image has 62166 counts for 7.331 counts/sec
Command not found; type ? for a command listing
!ad40020000g200470m:ASCA >
!ad40020000g200470m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g200470m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g200470m:ASCA > read events ad40020000g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g200470m:ASCA-GIS2-PH > set image sky
!ad40020000g200470m:ASCA-GIS2-PH > filter region corner_point.reg
!ad40020000g200470m:ASCA-GIS2-PH > extract image
!ad40020000g200470m:ASCA-GIS2-PH > save image outfile=ad40020000g200470m.img
Wrote image to file ad40020000g200470m.img
!ad40020000g200470m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad40020000g200470m:ASCA-GIS2-PH > extract image
!ad40020000g200470m:ASCA-GIS2-PH > save image outfile=ad40020000g200470m_lo.img
Wrote image to file ad40020000g200470m_lo.img
!ad40020000g200470m:ASCA-GIS2-PH > clear pha_cut
!ad40020000g200470m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g200470m:ASCA-GIS2-PH > extract image
!ad40020000g200470m:ASCA-GIS2-PH > save image outfile=ad40020000g200470m_hi.img
Wrote image to file ad40020000g200470m_hi.img
!ad40020000g200470m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad40020000g200570l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g200570l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 327.0049
Mean RA/DEC/ROLL : 308.0587 37.7262 327.0049
Pnt RA/DEC/ROLL : 308.0146 37.7650 327.0049
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 4
Total GTI (secs) : 96.159
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 23.9691238 23.9691238
20 Percent Complete: Total/live time: 23.9691238 23.9691238
30 Percent Complete: Total/live time: 30.8856468 30.8856468
40 Percent Complete: Total/live time: 79.8856506 79.8856506
50 Percent Complete: Total/live time: 79.8856506 79.8856506
60 Percent Complete: Total/live time: 88.0130386 88.0130386
70 Percent Complete: Total/live time: 88.0130386 88.0130386
80 Percent Complete: Total/live time: 96.1591339 96.1591339
100 Percent Complete: Total/live time: 96.1591339 96.1591339
Number of attitude steps used: 6
Number of attitude steps avail: 403
Mean RA/DEC pixel offset: -11.6592 -2.7731
writing expo file: ad40020000g200570l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g200570l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g200570l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 329 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 329 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
329 329 0 0 0 0
in 96.16 seconds
Image has 329 counts for 3.421 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 54 0 0 0 275
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
329 54 0 0 0 275
in 96.16 seconds
Image has 54 counts for 0.5616 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 276 0 0 0 53
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
329 276 0 0 0 53
in 96.16 seconds
Image has 276 counts for 2.870 counts/sec
Command not found; type ? for a command listing
!ad40020000g200570l:ASCA >
!ad40020000g200570l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g200570l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g200570l:ASCA > read events ad40020000g200570l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g200570l:ASCA-GIS2-PH > set image sky
!ad40020000g200570l:ASCA-GIS2-PH > filter region corner_point.reg
!ad40020000g200570l:ASCA-GIS2-PH > extract image
!ad40020000g200570l:ASCA-GIS2-PH > save image outfile=ad40020000g200570l.img
Wrote image to file ad40020000g200570l.img
!ad40020000g200570l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad40020000g200570l:ASCA-GIS2-PH > extract image
!ad40020000g200570l:ASCA-GIS2-PH > save image outfile=ad40020000g200570l_lo.img
Wrote image to file ad40020000g200570l_lo.img
!ad40020000g200570l:ASCA-GIS2-PH > clear pha_cut
!ad40020000g200570l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g200570l:ASCA-GIS2-PH > extract image
!ad40020000g200570l:ASCA-GIS2-PH > save image outfile=ad40020000g200570l_hi.img
Wrote image to file ad40020000g200570l_hi.img
!ad40020000g200570l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad40020000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad40020000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9828
Mean RA/DEC/ROLL : 308.0293 37.7603 326.9828
Pnt RA/DEC/ROLL : 308.0572 37.4781 326.9828
Image rebin factor : 1
Attitude Records : 44031
GTI intervals : 23
Total GTI (secs) : 9793.837
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1213.9913330 1213.9913330
20 Percent Complete: Total/live time: 2180.9267578 2180.9267578
30 Percent Complete: Total/live time: 3104.4238281 3104.4238281
40 Percent Complete: Total/live time: 4101.8403320 4101.8403320
50 Percent Complete: Total/live time: 5068.8374023 5068.8374023
60 Percent Complete: Total/live time: 6975.2343750 6975.2343750
70 Percent Complete: Total/live time: 6975.2343750 6975.2343750
80 Percent Complete: Total/live time: 7962.7314453 7962.7314453
90 Percent Complete: Total/live time: 9540.2177734 9540.2177734
100 Percent Complete: Total/live time: 9793.8369141 9793.8369141
Number of attitude steps used: 47
Number of attitude steps avail: 27841
Mean RA/DEC pixel offset: -0.3990 -1.1148
writing expo file: ad40020000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 109071 138 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
109209 109071 138 0 0 0
in 9793.84 seconds
Image has 109071 counts for 11.14 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 13419 138 0 0 95652
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
109209 13419 138 0 0 95652
in 9793.84 seconds
Image has 13419 counts for 1.370 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 95895 138 0 0 13176
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
109209 95895 138 0 0 13176
in 9793.84 seconds
Image has 95895 counts for 9.791 counts/sec
Command not found; type ? for a command listing
!ad40020000g300170h:ASCA >
!ad40020000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g300170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g300170h:ASCA > read events ad40020000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g300170h:ASCA-GIS3-PH > set image sky
!ad40020000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad40020000g300170h:ASCA-GIS3-PH > extract image
!ad40020000g300170h:ASCA-GIS3-PH > save image outfile=ad40020000g300170h.img
Wrote image to file ad40020000g300170h.img
!ad40020000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad40020000g300170h:ASCA-GIS3-PH > extract image
!ad40020000g300170h:ASCA-GIS3-PH > save image outfile=ad40020000g300170h_lo.img
Wrote image to file ad40020000g300170h_lo.img
!ad40020000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad40020000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g300170h:ASCA-GIS3-PH > extract image
!ad40020000g300170h:ASCA-GIS3-PH > save image outfile=ad40020000g300170h_hi.img
Wrote image to file ad40020000g300170h_hi.img
!ad40020000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad40020000g300370h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g300370h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9896
Mean RA/DEC/ROLL : 308.0343 37.7420 326.9896
Pnt RA/DEC/ROLL : 308.0366 37.7486 326.9896
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 18
Total GTI (secs) : 14231.618
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2059.9936523 2059.9936523
20 Percent Complete: Total/live time: 3291.4902344 3291.4902344
30 Percent Complete: Total/live time: 5453.0434570 5453.0434570
40 Percent Complete: Total/live time: 6041.0419922 6041.0419922
50 Percent Complete: Total/live time: 7777.5371094 7777.5371094
60 Percent Complete: Total/live time: 9539.9287109 9539.9287109
70 Percent Complete: Total/live time: 10544.0351562 10544.0351562
80 Percent Complete: Total/live time: 11643.9111328 11643.9111328
90 Percent Complete: Total/live time: 12975.7744141 12975.7744141
100 Percent Complete: Total/live time: 14231.6171875 14231.6171875
Number of attitude steps used: 52
Number of attitude steps avail: 31269
Mean RA/DEC pixel offset: -1.9287 -2.5186
writing expo file: ad40020000g300370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g300370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g300370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 166684 231 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
166915 166684 231 0 0 0
in 14231.62 seconds
Image has 166684 counts for 11.71 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 20722 231 0 0 145962
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
166915 20722 231 0 0 145962
in 14231.62 seconds
Image has 20722 counts for 1.456 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 146319 231 0 0 20365
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
166915 146319 231 0 0 20365
in 14231.62 seconds
Image has 146319 counts for 10.28 counts/sec
Command not found; type ? for a command listing
!ad40020000g300370h:ASCA >
!ad40020000g300370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g300370h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g300370h:ASCA > read events ad40020000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g300370h:ASCA-GIS3-PH > set image sky
!ad40020000g300370h:ASCA-GIS3-PH > filter region corner_point.reg
!ad40020000g300370h:ASCA-GIS3-PH > extract image
!ad40020000g300370h:ASCA-GIS3-PH > save image outfile=ad40020000g300370h.img
Wrote image to file ad40020000g300370h.img
!ad40020000g300370h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad40020000g300370h:ASCA-GIS3-PH > extract image
!ad40020000g300370h:ASCA-GIS3-PH > save image outfile=ad40020000g300370h_lo.img
Wrote image to file ad40020000g300370h_lo.img
!ad40020000g300370h:ASCA-GIS3-PH > clear pha_cut
!ad40020000g300370h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g300370h:ASCA-GIS3-PH > extract image
!ad40020000g300370h:ASCA-GIS3-PH > save image outfile=ad40020000g300370h_hi.img
Wrote image to file ad40020000g300370h_hi.img
!ad40020000g300370h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad40020000g300470m.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g300470m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9899
Mean RA/DEC/ROLL : 308.0344 37.7423 326.9899
Pnt RA/DEC/ROLL : 308.0364 37.7486 326.9899
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 11
Total GTI (secs) : 8479.991
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1102.9965820 1102.9965820
20 Percent Complete: Total/live time: 1966.9855957 1966.9855957
30 Percent Complete: Total/live time: 4047.0024414 4047.0024414
40 Percent Complete: Total/live time: 4047.0024414 4047.0024414
50 Percent Complete: Total/live time: 4735.0004883 4735.0004883
60 Percent Complete: Total/live time: 5178.9995117 5178.9995117
70 Percent Complete: Total/live time: 6034.9726562 6034.9726562
80 Percent Complete: Total/live time: 8048.0424805 8048.0424805
90 Percent Complete: Total/live time: 8048.0424805 8048.0424805
100 Percent Complete: Total/live time: 8479.9921875 8479.9921875
Number of attitude steps used: 53
Number of attitude steps avail: 10773
Mean RA/DEC pixel offset: -1.7161 -1.6692
writing expo file: ad40020000g300470m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g300470m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g300470m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 90774 121 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
90895 90774 121 0 0 0
in 8479.99 seconds
Image has 90774 counts for 10.70 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 11343 121 0 0 79431
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
90895 11343 121 0 0 79431
in 8479.99 seconds
Image has 11343 counts for 1.338 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 79653 121 0 0 11121
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
90895 79653 121 0 0 11121
in 8479.99 seconds
Image has 79653 counts for 9.393 counts/sec
Command not found; type ? for a command listing
!ad40020000g300470m:ASCA >
!ad40020000g300470m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g300470m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g300470m:ASCA > read events ad40020000g300470m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g300470m:ASCA-GIS3-PH > set image sky
!ad40020000g300470m:ASCA-GIS3-PH > filter region corner_point.reg
!ad40020000g300470m:ASCA-GIS3-PH > extract image
!ad40020000g300470m:ASCA-GIS3-PH > save image outfile=ad40020000g300470m.img
Wrote image to file ad40020000g300470m.img
!ad40020000g300470m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad40020000g300470m:ASCA-GIS3-PH > extract image
!ad40020000g300470m:ASCA-GIS3-PH > save image outfile=ad40020000g300470m_lo.img
Wrote image to file ad40020000g300470m_lo.img
!ad40020000g300470m:ASCA-GIS3-PH > clear pha_cut
!ad40020000g300470m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g300470m:ASCA-GIS3-PH > extract image
!ad40020000g300470m:ASCA-GIS3-PH > save image outfile=ad40020000g300470m_hi.img
Wrote image to file ad40020000g300470m_hi.img
!ad40020000g300470m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad40020000g300570l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000g300570l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9899
Mean RA/DEC/ROLL : 308.0341 37.7417 326.9899
Pnt RA/DEC/ROLL : 308.0391 37.7495 326.9899
Image rebin factor : 1
Attitude Records : 44225
GTI intervals : 4
Total GTI (secs) : 96.159
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 23.9691238 23.9691238
20 Percent Complete: Total/live time: 23.9691238 23.9691238
30 Percent Complete: Total/live time: 30.8856468 30.8856468
40 Percent Complete: Total/live time: 79.8856506 79.8856506
50 Percent Complete: Total/live time: 79.8856506 79.8856506
60 Percent Complete: Total/live time: 88.0130386 88.0130386
70 Percent Complete: Total/live time: 88.0130386 88.0130386
80 Percent Complete: Total/live time: 96.1591339 96.1591339
100 Percent Complete: Total/live time: 96.1591339 96.1591339
Number of attitude steps used: 6
Number of attitude steps avail: 403
Mean RA/DEC pixel offset: -1.5936 -1.7732
writing expo file: ad40020000g300570l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000g300570l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000g300570l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 350 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 349 1 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
350 349 1 0 0 0
in 96.16 seconds
Image has 349 counts for 3.629 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 28 1 0 0 321
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
350 28 1 0 0 321
in 96.16 seconds
Image has 28 counts for 0.2912 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 321 1 0 0 28
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
350 321 1 0 0 28
in 96.16 seconds
Image has 321 counts for 3.338 counts/sec
Command not found; type ? for a command listing
!ad40020000g300570l:ASCA >
!ad40020000g300570l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000g300570l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000g300570l:ASCA > read events ad40020000g300570l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000g300570l:ASCA-GIS3-PH > set image sky
!ad40020000g300570l:ASCA-GIS3-PH > filter region corner_point.reg
!ad40020000g300570l:ASCA-GIS3-PH > extract image
!ad40020000g300570l:ASCA-GIS3-PH > save image outfile=ad40020000g300570l.img
Wrote image to file ad40020000g300570l.img
!ad40020000g300570l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad40020000g300570l:ASCA-GIS3-PH > extract image
!ad40020000g300570l:ASCA-GIS3-PH > save image outfile=ad40020000g300570l_lo.img
Wrote image to file ad40020000g300570l_lo.img
!ad40020000g300570l:ASCA-GIS3-PH > clear pha_cut
!ad40020000g300570l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad40020000g300570l:ASCA-GIS3-PH > extract image
!ad40020000g300570l:ASCA-GIS3-PH > save image outfile=ad40020000g300570l_hi.img
Wrote image to file ad40020000g300570l_hi.img
!ad40020000g300570l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad40020000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9838
Mean RA/DEC/ROLL : 308.0331 37.7258 326.9838
Pnt RA/DEC/ROLL : 308.0562 37.4977 326.9838
Image rebin factor : 4
Attitude Records : 44031
Hot Pixels : 16
GTI intervals : 25
Total GTI (secs) : 10195.394
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1153.4816895 1153.4816895
20 Percent Complete: Total/live time: 2174.9782715 2174.9782715
30 Percent Complete: Total/live time: 3212.9301758 3212.9301758
40 Percent Complete: Total/live time: 4361.9633789 4361.9633789
50 Percent Complete: Total/live time: 5385.2866211 5385.2866211
60 Percent Complete: Total/live time: 6251.7841797 6251.7841797
70 Percent Complete: Total/live time: 7553.1752930 7553.1752930
80 Percent Complete: Total/live time: 8381.6728516 8381.6728516
90 Percent Complete: Total/live time: 9987.9892578 9987.9892578
100 Percent Complete: Total/live time: 10195.3945312 10195.3945312
Number of attitude steps used: 38
Number of attitude steps avail: 26028
Mean RA/DEC pixel offset: -58.7240 -82.9446
writing expo file: ad40020000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 100123 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100123 100123 0 0 0 0
in 10195.39 seconds
Image has 100123 counts for 9.820 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 14217 0 0 0 85906
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100123 14217 0 0 0 85906
in 10195.39 seconds
Image has 14217 counts for 1.394 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 85987 0 0 0 14136
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100123 85987 0 0 0 14136
in 10195.39 seconds
Image has 85987 counts for 8.434 counts/sec
Command not found; type ? for a command listing
!ad40020000s000102h:ASCA >
!ad40020000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s000102h:ASCA > read events ad40020000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad40020000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad40020000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000102h.img
Wrote image to file ad40020000s000102h.img
!ad40020000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad40020000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000102h_lo.img
Wrote image to file ad40020000s000102h_lo.img
!ad40020000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad40020000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000102h_hi.img
Wrote image to file ad40020000s000102h_hi.img
!ad40020000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s000202l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s000202l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9853
Mean RA/DEC/ROLL : 308.0291 37.7222 326.9853
Pnt RA/DEC/ROLL : 308.0502 37.7737 326.9853
Image rebin factor : 4
Attitude Records : 44031
Hot Pixels : 5
GTI intervals : 4
Total GTI (secs) : 480.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 62.9721718 62.9721718
20 Percent Complete: Total/live time: 128.0000000 128.0000000
30 Percent Complete: Total/live time: 190.9517517 190.9517517
40 Percent Complete: Total/live time: 256.0000000 256.0000000
50 Percent Complete: Total/live time: 256.0000000 256.0000000
60 Percent Complete: Total/live time: 384.0000000 384.0000000
70 Percent Complete: Total/live time: 384.0000000 384.0000000
80 Percent Complete: Total/live time: 480.0000000 480.0000000
100 Percent Complete: Total/live time: 480.0000000 480.0000000
Number of attitude steps used: 6
Number of attitude steps avail: 6060
Mean RA/DEC pixel offset: -46.6712 -75.0801
writing expo file: ad40020000s000202l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s000202l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s000202l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 3524 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3524 3524 0 0 0 0
in 480.00 seconds
Image has 3524 counts for 7.342 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 515 0 0 0 3009
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3524 515 0 0 0 3009
in 480.00 seconds
Image has 515 counts for 1.073 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 3013 0 0 0 511
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3524 3013 0 0 0 511
in 480.00 seconds
Image has 3013 counts for 6.277 counts/sec
Command not found; type ? for a command listing
!ad40020000s000202l:ASCA >
!ad40020000s000202l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s000202l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s000202l:ASCA > read events ad40020000s000202l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s000202l:ASCA-SIS0-BRIGHT > set image sky
!ad40020000s000202l:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad40020000s000202l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000202l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000202l.img
Wrote image to file ad40020000s000202l.img
!ad40020000s000202l:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad40020000s000202l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000202l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000202l_lo.img
Wrote image to file ad40020000s000202l_lo.img
!ad40020000s000202l:ASCA-SIS0-BRIGHT > clear pha_cut
!ad40020000s000202l:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s000202l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000202l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000202l_hi.img
Wrote image to file ad40020000s000202l_hi.img
!ad40020000s000202l:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s000402h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s000402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9906
Mean RA/DEC/ROLL : 308.0360 37.7214 326.9906
Pnt RA/DEC/ROLL : 308.0350 37.7691 326.9906
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 19
GTI intervals : 20
Total GTI (secs) : 12523.438
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1945.9796143 1945.9796143
20 Percent Complete: Total/live time: 3087.4448242 3087.4448242
30 Percent Complete: Total/live time: 3886.4423828 3886.4423828
40 Percent Complete: Total/live time: 5628.9277344 5628.9277344
50 Percent Complete: Total/live time: 6437.9252930 6437.9252930
60 Percent Complete: Total/live time: 7710.3276367 7710.3276367
70 Percent Complete: Total/live time: 9311.6894531 9311.6894531
80 Percent Complete: Total/live time: 10833.6728516 10833.6728516
90 Percent Complete: Total/live time: 11887.6250000 11887.6250000
100 Percent Complete: Total/live time: 12523.4394531 12523.4394531
Number of attitude steps used: 46
Number of attitude steps avail: 27651
Mean RA/DEC pixel offset: -71.9197 -89.0190
writing expo file: ad40020000s000402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s000402h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s000402h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 125309 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125309 125309 0 0 0 0
in 12523.44 seconds
Image has 125309 counts for 10.01 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 18161 0 0 0 107148
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125309 18161 0 0 0 107148
in 12523.44 seconds
Image has 18161 counts for 1.450 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 107265 0 0 0 18044
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125309 107265 0 0 0 18044
in 12523.44 seconds
Image has 107265 counts for 8.565 counts/sec
Command not found; type ? for a command listing
!ad40020000s000402h:ASCA >
!ad40020000s000402h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s000402h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s000402h:ASCA > read events ad40020000s000402h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s000402h:ASCA-SIS0-BRIGHT > set image sky
!ad40020000s000402h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad40020000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000402h.img
Wrote image to file ad40020000s000402h.img
!ad40020000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad40020000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000402h_lo.img
Wrote image to file ad40020000s000402h_lo.img
!ad40020000s000402h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad40020000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000402h_hi.img
Wrote image to file ad40020000s000402h_hi.img
!ad40020000s000402h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s000502m.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s000502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9913
Mean RA/DEC/ROLL : 308.0361 37.7217 326.9913
Pnt RA/DEC/ROLL : 308.0349 37.7691 326.9913
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 22
GTI intervals : 15
Total GTI (secs) : 7163.343
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1094.9963379 1094.9963379
20 Percent Complete: Total/live time: 1531.7445068 1531.7445068
30 Percent Complete: Total/live time: 2232.7421875 2232.7421875
40 Percent Complete: Total/live time: 3772.7294922 3772.7294922
50 Percent Complete: Total/live time: 3772.7294922 3772.7294922
60 Percent Complete: Total/live time: 4460.7275391 4460.7275391
70 Percent Complete: Total/live time: 5140.7255859 5140.7255859
80 Percent Complete: Total/live time: 5862.7656250 5862.7656250
90 Percent Complete: Total/live time: 6699.5029297 6699.5029297
100 Percent Complete: Total/live time: 7163.3442383 7163.3442383
Number of attitude steps used: 48
Number of attitude steps avail: 7978
Mean RA/DEC pixel offset: -69.7441 -88.3103
writing expo file: ad40020000s000502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s000502m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s000502m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 68953 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68953 68953 0 0 0 0
in 7163.34 seconds
Image has 68953 counts for 9.626 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 9942 0 0 0 59011
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68953 9942 0 0 0 59011
in 7163.34 seconds
Image has 9942 counts for 1.388 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 59078 0 0 0 9875
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68953 59078 0 0 0 9875
in 7163.34 seconds
Image has 59078 counts for 8.247 counts/sec
Command not found; type ? for a command listing
!ad40020000s000502m:ASCA >
!ad40020000s000502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s000502m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s000502m:ASCA > read events ad40020000s000502m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s000502m:ASCA-SIS0-BRIGHT > set image sky
!ad40020000s000502m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad40020000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000502m.img
Wrote image to file ad40020000s000502m.img
!ad40020000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad40020000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000502m_lo.img
Wrote image to file ad40020000s000502m_lo.img
!ad40020000s000502m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad40020000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000502m_hi.img
Wrote image to file ad40020000s000502m_hi.img
!ad40020000s000502m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s000602l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s000602l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9909
Mean RA/DEC/ROLL : 308.0345 37.7219 326.9909
Pnt RA/DEC/ROLL : 308.0375 37.7702 326.9909
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 5
GTI intervals : 3
Total GTI (secs) : 480.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 54.8745155 54.8745155
20 Percent Complete: Total/live time: 352.0000000 352.0000000
30 Percent Complete: Total/live time: 352.0000000 352.0000000
40 Percent Complete: Total/live time: 406.8414001 406.8414001
50 Percent Complete: Total/live time: 406.8414001 406.8414001
60 Percent Complete: Total/live time: 480.0000000 480.0000000
100 Percent Complete: Total/live time: 480.0000000 480.0000000
Number of attitude steps used: 4
Number of attitude steps avail: 325
Mean RA/DEC pixel offset: -50.2245 -70.0455
writing expo file: ad40020000s000602l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s000602l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s000602l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.48E+03 3427 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 3427 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3427 3427 0 0 0 0
in 480.00 seconds
Image has 3427 counts for 7.140 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 538 0 0 0 2889
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3427 538 0 0 0 2889
in 480.00 seconds
Image has 538 counts for 1.121 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 2891 0 0 0 536
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3427 2891 0 0 0 536
in 480.00 seconds
Image has 2891 counts for 6.023 counts/sec
Command not found; type ? for a command listing
!ad40020000s000602l:ASCA >
!ad40020000s000602l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s000602l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s000602l:ASCA > read events ad40020000s000602l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s000602l:ASCA-SIS0-BRIGHT > set image sky
!ad40020000s000602l:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad40020000s000602l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000602l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000602l.img
Wrote image to file ad40020000s000602l.img
!ad40020000s000602l:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad40020000s000602l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000602l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000602l_lo.img
Wrote image to file ad40020000s000602l_lo.img
!ad40020000s000602l:ASCA-SIS0-BRIGHT > clear pha_cut
!ad40020000s000602l:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s000602l:ASCA-SIS0-BRIGHT > extract image
!ad40020000s000602l:ASCA-SIS0-BRIGHT > save image outfile=ad40020000s000602l_hi.img
Wrote image to file ad40020000s000602l_hi.img
!ad40020000s000602l:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9911
Mean RA/DEC/ROLL : 308.0446 37.7408 326.9911
Pnt RA/DEC/ROLL : 308.0443 37.4849 326.9911
Image rebin factor : 4
Attitude Records : 44031
Hot Pixels : 24
GTI intervals : 26
Total GTI (secs) : 10181.492
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1378.4805908 1378.4805908
20 Percent Complete: Total/live time: 2326.0253906 2326.0253906
30 Percent Complete: Total/live time: 3283.3671875 3283.3671875
40 Percent Complete: Total/live time: 4273.9008789 4273.9008789
50 Percent Complete: Total/live time: 5297.2241211 5297.2241211
60 Percent Complete: Total/live time: 6355.7211914 6355.7211914
70 Percent Complete: Total/live time: 7513.2426758 7513.2426758
80 Percent Complete: Total/live time: 8341.7402344 8341.7402344
90 Percent Complete: Total/live time: 9980.0566406 9980.0566406
100 Percent Complete: Total/live time: 10181.4931641 10181.4931641
Number of attitude steps used: 38
Number of attitude steps avail: 26010
Mean RA/DEC pixel offset: -63.0514 -12.9843
writing expo file: ad40020000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 81930 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
81930 81930 0 0 0 0
in 10181.49 seconds
Image has 81930 counts for 8.047 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 12380 0 0 0 69550
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
81930 12380 0 0 0 69550
in 10181.49 seconds
Image has 12380 counts for 1.216 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 69601 0 0 0 12329
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
81930 69601 0 0 0 12329
in 10181.49 seconds
Image has 69601 counts for 6.836 counts/sec
Command not found; type ? for a command listing
!ad40020000s100102h:ASCA >
!ad40020000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s100102h:ASCA > read events ad40020000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad40020000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad40020000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100102h.img
Wrote image to file ad40020000s100102h.img
!ad40020000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad40020000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100102h_lo.img
Wrote image to file ad40020000s100102h_lo.img
!ad40020000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad40020000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100102h_hi.img
Wrote image to file ad40020000s100102h_hi.img
!ad40020000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s100202l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s100202l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_0242.1244
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9926
Mean RA/DEC/ROLL : 308.0411 37.7351 326.9926
Pnt RA/DEC/ROLL : 308.0382 37.7610 326.9926
Image rebin factor : 4
Attitude Records : 44031
Hot Pixels : 10
GTI intervals : 6
Total GTI (secs) : 384.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 64.0000000 64.0000000
20 Percent Complete: Total/live time: 96.0000000 96.0000000
30 Percent Complete: Total/live time: 160.0000000 160.0000000
40 Percent Complete: Total/live time: 160.0000000 160.0000000
50 Percent Complete: Total/live time: 288.0000000 288.0000000
60 Percent Complete: Total/live time: 288.0000000 288.0000000
70 Percent Complete: Total/live time: 384.0000000 384.0000000
100 Percent Complete: Total/live time: 384.0000000 384.0000000
Number of attitude steps used: 6
Number of attitude steps avail: 6060
Mean RA/DEC pixel offset: -50.3748 -15.2041
writing expo file: ad40020000s100202l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s100202l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s100202l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 2503 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2503 2503 0 0 0 0
in 384.00 seconds
Image has 2503 counts for 6.518 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 380 0 0 0 2123
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2503 380 0 0 0 2123
in 384.00 seconds
Image has 380 counts for 0.9896 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 2125 0 0 0 378
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2503 2125 0 0 0 378
in 384.00 seconds
Image has 2125 counts for 5.534 counts/sec
Command not found; type ? for a command listing
!ad40020000s100202l:ASCA >
!ad40020000s100202l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s100202l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s100202l:ASCA > read events ad40020000s100202l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s100202l:ASCA-SIS1-BRIGHT > set image sky
!ad40020000s100202l:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad40020000s100202l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100202l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100202l.img
Wrote image to file ad40020000s100202l.img
!ad40020000s100202l:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad40020000s100202l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100202l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100202l_lo.img
Wrote image to file ad40020000s100202l_lo.img
!ad40020000s100202l:ASCA-SIS1-BRIGHT > clear pha_cut
!ad40020000s100202l:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s100202l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100202l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100202l_hi.img
Wrote image to file ad40020000s100202l_hi.img
!ad40020000s100202l:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s100402h.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s100402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9979
Mean RA/DEC/ROLL : 308.0479 37.7342 326.9979
Pnt RA/DEC/ROLL : 308.0230 37.7563 326.9979
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 25
GTI intervals : 22
Total GTI (secs) : 12487.476
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1955.9483643 1955.9483643
20 Percent Complete: Total/live time: 3101.4135742 3101.4135742
30 Percent Complete: Total/live time: 3891.9111328 3891.9111328
40 Percent Complete: Total/live time: 5564.9648438 5564.9648438
50 Percent Complete: Total/live time: 6373.9624023 6373.9624023
60 Percent Complete: Total/live time: 7706.3647461 7706.3647461
70 Percent Complete: Total/live time: 8883.7275391 8883.7275391
80 Percent Complete: Total/live time: 10797.7099609 10797.7099609
90 Percent Complete: Total/live time: 11851.6611328 11851.6611328
100 Percent Complete: Total/live time: 12487.4755859 12487.4755859
Number of attitude steps used: 48
Number of attitude steps avail: 27832
Mean RA/DEC pixel offset: -75.5960 -18.6020
writing expo file: ad40020000s100402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s100402h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s100402h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 104295 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
104295 104295 0 0 0 0
in 12487.48 seconds
Image has 104295 counts for 8.352 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 15911 0 0 0 88384
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
104295 15911 0 0 0 88384
in 12487.48 seconds
Image has 15911 counts for 1.274 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 88474 0 0 0 15821
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
104295 88474 0 0 0 15821
in 12487.48 seconds
Image has 88474 counts for 7.085 counts/sec
Command not found; type ? for a command listing
!ad40020000s100402h:ASCA >
!ad40020000s100402h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s100402h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s100402h:ASCA > read events ad40020000s100402h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s100402h:ASCA-SIS1-BRIGHT > set image sky
!ad40020000s100402h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad40020000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100402h.img
Wrote image to file ad40020000s100402h.img
!ad40020000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad40020000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100402h_lo.img
Wrote image to file ad40020000s100402h_lo.img
!ad40020000s100402h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad40020000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100402h_hi.img
Wrote image to file ad40020000s100402h_hi.img
!ad40020000s100402h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s100502m.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s100502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9982
Mean RA/DEC/ROLL : 308.0481 37.7345 326.9982
Pnt RA/DEC/ROLL : 308.0229 37.7563 326.9982
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 26
GTI intervals : 16
Total GTI (secs) : 7137.734
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1080.9965820 1080.9965820
20 Percent Complete: Total/live time: 1517.7447510 1517.7447510
30 Percent Complete: Total/live time: 3726.7297363 3726.7297363
40 Percent Complete: Total/live time: 3726.7297363 3726.7297363
50 Percent Complete: Total/live time: 4414.7275391 4414.7275391
60 Percent Complete: Total/live time: 4414.7275391 4414.7275391
70 Percent Complete: Total/live time: 5094.7255859 5094.7255859
80 Percent Complete: Total/live time: 5848.7656250 5848.7656250
90 Percent Complete: Total/live time: 6717.5029297 6717.5029297
100 Percent Complete: Total/live time: 7137.7353516 7137.7353516
Number of attitude steps used: 46
Number of attitude steps avail: 7984
Mean RA/DEC pixel offset: -74.0532 -17.8369
writing expo file: ad40020000s100502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s100502m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s100502m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 57736 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57736 57736 0 0 0 0
in 7137.73 seconds
Image has 57736 counts for 8.089 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 8791 0 0 0 48945
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57736 8791 0 0 0 48945
in 7137.73 seconds
Image has 8791 counts for 1.232 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 48986 0 0 0 8750
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57736 48986 0 0 0 8750
in 7137.73 seconds
Image has 48986 counts for 6.863 counts/sec
Command not found; type ? for a command listing
!ad40020000s100502m:ASCA >
!ad40020000s100502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s100502m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s100502m:ASCA > read events ad40020000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s100502m:ASCA-SIS1-BRIGHT > set image sky
!ad40020000s100502m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad40020000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100502m.img
Wrote image to file ad40020000s100502m.img
!ad40020000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad40020000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100502m_lo.img
Wrote image to file ad40020000s100502m_lo.img
!ad40020000s100502m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad40020000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100502m_hi.img
Wrote image to file ad40020000s100502m_hi.img
!ad40020000s100502m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad40020000s100602l.expo
ASCAEXPO_V0.9b
reading data file: ad40020000s100602l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930701_1244.0420
making an exposure map...
Aspect RA/DEC/ROLL : 308.0330 37.7474 326.9982
Mean RA/DEC/ROLL : 308.0467 37.7345 326.9982
Pnt RA/DEC/ROLL : 308.0255 37.7574 326.9982
Image rebin factor : 4
Attitude Records : 44225
Hot Pixels : 11
GTI intervals : 3
Total GTI (secs) : 448.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 54.8745155 54.8745155
20 Percent Complete: Total/live time: 352.0000000 352.0000000
30 Percent Complete: Total/live time: 352.0000000 352.0000000
40 Percent Complete: Total/live time: 406.8414001 406.8414001
50 Percent Complete: Total/live time: 406.8414001 406.8414001
60 Percent Complete: Total/live time: 448.0000000 448.0000000
100 Percent Complete: Total/live time: 448.0000000 448.0000000
Number of attitude steps used: 4
Number of attitude steps avail: 323
Mean RA/DEC pixel offset: -53.5666 -16.1177
writing expo file: ad40020000s100602l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad40020000s100602l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad40020000s100602l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.45E+03 2936 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 2936 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2936 2936 0 0 0 0
in 448.00 seconds
Image has 2936 counts for 6.554 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 456 0 0 0 2480
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2936 456 0 0 0 2480
in 448.00 seconds
Image has 456 counts for 1.018 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 2481 0 0 0 455
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2936 2481 0 0 0 455
in 448.00 seconds
Image has 2481 counts for 5.538 counts/sec
Command not found; type ? for a command listing
!ad40020000s100602l:ASCA >
!ad40020000s100602l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad40020000s100602l:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!ad40020000s100602l:ASCA > read events ad40020000s100602l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!ad40020000s100602l:ASCA-SIS1-BRIGHT > set image sky
!ad40020000s100602l:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad40020000s100602l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100602l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100602l.img
Wrote image to file ad40020000s100602l.img
!ad40020000s100602l:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad40020000s100602l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100602l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100602l_lo.img
Wrote image to file ad40020000s100602l_lo.img
!ad40020000s100602l:ASCA-SIS1-BRIGHT > clear pha_cut
!ad40020000s100602l:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad40020000s100602l:ASCA-SIS1-BRIGHT > extract image
!ad40020000s100602l:ASCA-SIS1-BRIGHT > save image outfile=ad40020000s100602l_hi.img
Wrote image to file ad40020000s100602l_hi.img
!ad40020000s100602l:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad40020000s000102h.expo ad40020000s000202l.expo ad40020000s000402h.expo ad40020000s000502m.expo ad40020000s000602l.expo ad40020000s100102h.expo ad40020000s100202l.expo ad40020000s100402h.expo ad40020000s100502m.expo ad40020000s100602l.expo-> Summing the following images to produce ad40020000sis32002_all.totsky
ad40020000s000102h.img ad40020000s000202l.img ad40020000s000402h.img ad40020000s000502m.img ad40020000s000602l.img ad40020000s100102h.img ad40020000s100202l.img ad40020000s100402h.img ad40020000s100502m.img ad40020000s100602l.img-> Summing the following images to produce ad40020000sis32002_lo.totsky
ad40020000s000102h_lo.img ad40020000s000202l_lo.img ad40020000s000402h_lo.img ad40020000s000502m_lo.img ad40020000s000602l_lo.img ad40020000s100102h_lo.img ad40020000s100202l_lo.img ad40020000s100402h_lo.img ad40020000s100502m_lo.img ad40020000s100602l_lo.img-> Summing the following images to produce ad40020000sis32002_hi.totsky
ad40020000s000102h_hi.img ad40020000s000202l_hi.img ad40020000s000402h_hi.img ad40020000s000502m_hi.img ad40020000s000602l_hi.img ad40020000s100102h_hi.img ad40020000s100202l_hi.img ad40020000s100402h_hi.img ad40020000s100502m_hi.img ad40020000s100602l_hi.img-> Running XIMAGE to create ad40020000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad40020000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 2278.00 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 2278 min: 0 ![2]XIMAGE> read/exp_map ad40020000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 1024.68 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1024 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 12295 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 8.00000 80 -1 i,inten,mm,pp 3 22.0000 22 0 i,inten,mm,pp 4 74.0000 74 0 ![9]XIMAGE> exit-> Summing gis images
ad40020000g200170h.expo ad40020000g200370h.expo ad40020000g200470m.expo ad40020000g200570l.expo ad40020000g300170h.expo ad40020000g300370h.expo ad40020000g300470m.expo ad40020000g300570l.expo-> Summing the following images to produce ad40020000gis25670_all.totsky
ad40020000g200170h.img ad40020000g200370h.img ad40020000g200470m.img ad40020000g200570l.img ad40020000g300170h.img ad40020000g300370h.img ad40020000g300470m.img ad40020000g300570l.img-> Summing the following images to produce ad40020000gis25670_lo.totsky
ad40020000g200170h_lo.img ad40020000g200370h_lo.img ad40020000g200470m_lo.img ad40020000g200570l_lo.img ad40020000g300170h_lo.img ad40020000g300370h_lo.img ad40020000g300470m_lo.img ad40020000g300570l_lo.img-> Summing the following images to produce ad40020000gis25670_hi.totsky
ad40020000g200170h_hi.img ad40020000g200370h_hi.img ad40020000g200470m_hi.img ad40020000g200570l_hi.img ad40020000g300170h_hi.img ad40020000g300370h_hi.img ad40020000g300470m_hi.img ad40020000g300570l_hi.img-> Running XIMAGE to create ad40020000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad40020000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 4963.00 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4963 min: 0 ![2]XIMAGE> read/exp_map ad40020000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1086.75 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1086 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 8694 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 40.0000 40 0 ![9]XIMAGE> exit
120 105 0.0577698 119 7 3134.13-> Smoothing ad40020000gis25670_hi.totsky with ad40020000gis25670.totexpo
120 105 0.0521226 119 7 4115.01-> Smoothing ad40020000gis25670_lo.totsky with ad40020000gis25670.totexpo
120 105 0.0057613 119 8 1173.21-> Determining extraction radii
120 105 24 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad40020000gis25670.src
138 106 0.0279439 92 8 1068.55-> Smoothing ad40020000sis32002_hi.totsky with ad40020000sis32002.totexpo
138 106 0.0243219 92 8 1097.03-> Smoothing ad40020000sis32002_lo.totsky with ad40020000sis32002.totexpo
139 106 0.00368705 91 9 732.514-> Determining extraction radii
138 106 38 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad40020000sis32002.src
The sum of the selected column is 392601.00 The mean of the selected column is 413.26421 The standard deviation of the selected column is 3.5779272 The minimum of selected column is 406.00000 The maximum of selected column is 423.00000 The number of points used in calculation is 950-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 440306.00 The mean of the selected column is 463.48000 The standard deviation of the selected column is 3.7098564 The minimum of selected column is 454.00000 The maximum of selected column is 473.00000 The number of points used in calculation is 950-> Converting (552.0,424.0,2.0) to s1 detector coordinates
The sum of the selected column is 352323.00 The mean of the selected column is 411.59229 The standard deviation of the selected column is 3.8129832 The minimum of selected column is 404.00000 The maximum of selected column is 421.00000 The number of points used in calculation is 856-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 427613.00 The mean of the selected column is 499.54790 The standard deviation of the selected column is 3.6989071 The minimum of selected column is 491.00000 The maximum of selected column is 510.00000 The number of points used in calculation is 856-> Converting (120.0,105.0,2.0) to g2 detector coordinates
The sum of the selected column is 2125333.0 The mean of the selected column is 101.67112 The standard deviation of the selected column is 1.1156603 The minimum of selected column is 99.000000 The maximum of selected column is 105.00000 The number of points used in calculation is 20904-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2352268.0 The mean of the selected column is 112.52717 The standard deviation of the selected column is 1.1438757 The minimum of selected column is 110.00000 The maximum of selected column is 116.00000 The number of points used in calculation is 20904-> Converting (120.0,105.0,2.0) to g3 detector coordinates
The sum of the selected column is 3414020.0 The mean of the selected column is 107.50787 The standard deviation of the selected column is 1.1029088 The minimum of selected column is 105.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 31756-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3590505.0 The mean of the selected column is 113.06540 The standard deviation of the selected column is 1.1177157 The minimum of selected column is 110.00000 The maximum of selected column is 116.00000 The number of points used in calculation is 31756
1 ad40020000s000102h.evt 301336 1 ad40020000s000202l.evt 301336 1 ad40020000s000402h.evt 301336 1 ad40020000s000502m.evt 301336 1 ad40020000s000602l.evt 301336-> Fetching SIS0_NOTCHIP0.1
ad40020000s000102h.evt ad40020000s000202l.evt ad40020000s000402h.evt ad40020000s000502m.evt ad40020000s000602l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
5 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.48E+03 3427 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 89867 10256 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 3272 252 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 112723 12586 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 61859 7094 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 3181 246 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
301336 270902 30434 0 0 0
in 30842.17 seconds
Spectrum has 270902 counts for 8.783 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 30842. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000202l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000602l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad40020000s010102_1.pi group=yes
Wrote spectrum to ad40020000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad40020000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 30842. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 323 are single channels ... 324 - 325 are grouped by a factor 2 ... 326 - 326 are single channels ... 327 - 346 are grouped by a factor 2 ... 347 - 364 are grouped by a factor 3 ... 365 - 372 are grouped by a factor 4 ... 373 - 375 are grouped by a factor 3 ... 376 - 380 are grouped by a factor 5 ... 381 - 384 are grouped by a factor 4 ... 385 - 394 are grouped by a factor 5 ... 395 - 401 are grouped by a factor 7 ... 402 - 410 are grouped by a factor 9 ... 411 - 422 are grouped by a factor 12 ... 423 - 435 are grouped by a factor 13 ... 436 - 452 are grouped by a factor 17 ... 453 - 478 are grouped by a factor 26 ... 479 - 486 are grouped by a factor 8 ... --------------------------------------------- ... ...... exiting, changes written to file : ad40020000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad40020000s010102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 40 bins
expanded to 39 by 40 bins
First WMAP bin is at detector pixel 264 312
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 423.00 475.00 (detector coordinates)
Point source at 29.97 10.50 (WMAP bins wrt optical axis)
Point source at 6.74 19.31 (... in polar coordinates)
Total counts in region = 2.70835E+05
Weighted mean angle from optical axis = 6.866 arcmin
-> Standard Output From STOOL group_event_files:1 ad40020000s100102h.evt 249400 1 ad40020000s100202l.evt 249400 1 ad40020000s100402h.evt 249400 1 ad40020000s100502m.evt 249400 1 ad40020000s100602l.evt 249400-> Fetching SIS1_NOTCHIP0.1
ad40020000s100102h.evt ad40020000s100202l.evt ad40020000s100402h.evt ad40020000s100502m.evt ad40020000s100602l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
5 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.45E+03 2936 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 74931 6999 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 2353 150 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 95571 8724 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 52714 5022 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 2754 182 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
249400 228323 21077 0 0 0
in 30638.70 seconds
Spectrum has 228323 counts for 7.452 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 30639. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.33105E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100202l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100602l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad40020000s110102_1.pi group=yes
Wrote spectrum to ad40020000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad40020000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 30639. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.33105E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 14 are single channels ... 15 - 16 are grouped by a factor 2 ... 17 - 299 are single channels ... 300 - 301 are grouped by a factor 2 ... 302 - 310 are single channels ... 311 - 312 are grouped by a factor 2 ... 313 - 316 are single channels ... 317 - 318 are grouped by a factor 2 ... 319 - 319 are single channels ... 320 - 343 are grouped by a factor 2 ... 344 - 352 are grouped by a factor 3 ... 353 - 354 are grouped by a factor 2 ... 355 - 363 are grouped by a factor 3 ... 364 - 371 are grouped by a factor 4 ... 372 - 377 are grouped by a factor 6 ... 378 - 385 are grouped by a factor 4 ... 386 - 391 are grouped by a factor 6 ... 392 - 398 are grouped by a factor 7 ... 399 - 407 are grouped by a factor 9 ... 408 - 427 are grouped by a factor 20 ... 428 - 436 are grouped by a factor 9 ... 437 - 439 are grouped by a factor 3 ... --------------------------------------------- ... ...... exiting, changes written to file : ad40020000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad40020000s110102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 35 bins
expanded to 39 by 35 bins
First WMAP bin is at detector pixel 264 352
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 49.907 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 423.00 495.00 (detector coordinates)
Point source at 24.41 34.85 (WMAP bins wrt optical axis)
Point source at 9.03 54.99 (... in polar coordinates)
Total counts in region = 2.28266E+05
Weighted mean angle from optical axis = 8.876 arcmin
-> Standard Output From STOOL group_event_files:1 ad40020000g200170h.evt 282496 1 ad40020000g200370h.evt 282496 1 ad40020000g200470m.evt 282496 1 ad40020000g200570l.evt 282496-> GIS2_REGION256.4 already present in current directory
ad40020000g200170h.evt ad40020000g200370h.evt ad40020000g200470m.evt ad40020000g200570l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
4 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 329 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 66759 16576 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 102344 25093 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 57231 14164 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 256 73 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
282496 226590 55906 0 0 0
in 32603.60 seconds
Spectrum has 226590 counts for 6.950 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32604. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad40020000g210170_1.pi group=yes
Wrote spectrum to ad40020000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad40020000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad40020000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32604. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 20 are grouped by a factor 21 ... 21 - 23 are grouped by a factor 3 ... 24 - 35 are grouped by a factor 2 ... 36 - 38 are grouped by a factor 3 ... 39 - 54 are grouped by a factor 2 ... 55 - 55 are single channels ... 56 - 59 are grouped by a factor 2 ... 60 - 61 are single channels ... 62 - 65 are grouped by a factor 2 ... 66 - 67 are single channels ... 68 - 69 are grouped by a factor 2 ... 70 - 78 are single channels ... 79 - 80 are grouped by a factor 2 ... 81 - 753 are single channels ... 754 - 755 are grouped by a factor 2 ... 756 - 767 are single channels ... 768 - 769 are grouped by a factor 2 ... 770 - 773 are single channels ... 774 - 785 are grouped by a factor 2 ... 786 - 787 are single channels ... 788 - 793 are grouped by a factor 2 ... 794 - 794 are single channels ... 795 - 800 are grouped by a factor 2 ... 801 - 801 are single channels ... 802 - 813 are grouped by a factor 2 ... 814 - 814 are single channels ... 815 - 844 are grouped by a factor 2 ... 845 - 847 are grouped by a factor 3 ... 848 - 869 are grouped by a factor 2 ... 870 - 878 are grouped by a factor 3 ... 879 - 880 are grouped by a factor 2 ... 881 - 898 are grouped by a factor 3 ... 899 - 902 are grouped by a factor 4 ... 903 - 908 are grouped by a factor 3 ... 909 - 912 are grouped by a factor 4 ... 913 - 918 are grouped by a factor 3 ... 919 - 922 are grouped by a factor 4 ... 923 - 925 are grouped by a factor 3 ... 926 - 949 are grouped by a factor 4 ... 950 - 954 are grouped by a factor 5 ... 955 - 961 are grouped by a factor 7 ... 962 - 969 are grouped by a factor 8 ... 970 - 986 are grouped by a factor 17 ... 987 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad40020000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 40 51
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 102.00 113.00 (detector coordinates)
Point source at 31.00 17.96 (WMAP bins wrt optical axis)
Point source at 8.80 30.09 (... in polar coordinates)
Total counts in region = 2.26590E+05
Weighted mean angle from optical axis = 8.815 arcmin
-> Standard Output From STOOL group_event_files:1 ad40020000g300170h.evt 367369 1 ad40020000g300370h.evt 367369 1 ad40020000g300470m.evt 367369 1 ad40020000g300570l.evt 367369-> GIS3_REGION256.4 already present in current directory
ad40020000g300170h.evt ad40020000g300370h.evt ad40020000g300470m.evt ad40020000g300570l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
4 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 350 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 91535 17674 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 140037 26878 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 76035 14860 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 288 62 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
367369 307895 59474 0 0 0
in 32601.60 seconds
Spectrum has 307895 counts for 9.444 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32602. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad40020000g310170_1.pi group=yes
Wrote spectrum to ad40020000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad40020000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad40020000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32602. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 21 are grouped by a factor 22 ... 22 - 33 are grouped by a factor 2 ... 34 - 34 are single channels ... 35 - 48 are grouped by a factor 2 ... 49 - 49 are single channels ... 50 - 51 are grouped by a factor 2 ... 52 - 53 are single channels ... 54 - 55 are grouped by a factor 2 ... 56 - 56 are single channels ... 57 - 58 are grouped by a factor 2 ... 59 - 66 are single channels ... 67 - 68 are grouped by a factor 2 ... 69 - 820 are single channels ... 821 - 822 are grouped by a factor 2 ... 823 - 826 are single channels ... 827 - 828 are grouped by a factor 2 ... 829 - 835 are single channels ... 836 - 837 are grouped by a factor 2 ... 838 - 840 are single channels ... 841 - 842 are grouped by a factor 2 ... 843 - 844 are single channels ... 845 - 848 are grouped by a factor 2 ... 849 - 849 are single channels ... 850 - 851 are grouped by a factor 2 ... 852 - 855 are single channels ... 856 - 861 are grouped by a factor 2 ... 862 - 862 are single channels ... 863 - 912 are grouped by a factor 2 ... 913 - 915 are grouped by a factor 3 ... 916 - 921 are grouped by a factor 2 ... 922 - 924 are grouped by a factor 3 ... 925 - 928 are grouped by a factor 2 ... 929 - 934 are grouped by a factor 3 ... 935 - 936 are grouped by a factor 2 ... 937 - 951 are grouped by a factor 3 ... 952 - 955 are grouped by a factor 4 ... 956 - 970 are grouped by a factor 3 ... 971 - 975 are grouped by a factor 5 ... 976 - 978 are grouped by a factor 3 ... 979 - 983 are grouped by a factor 5 ... 984 - 987 are grouped by a factor 4 ... 988 - 992 are grouped by a factor 5 ... 993 - 1011 are grouped by a factor 19 ... 1012 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad40020000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 46 51
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 108.00 113.00 (detector coordinates)
Point source at 11.36 21.44 (WMAP bins wrt optical axis)
Point source at 5.96 62.08 (... in polar coordinates)
Total counts in region = 3.07895E+05
Weighted mean angle from optical axis = 6.132 arcmin
-> Plotting ad40020000g210170_1_pi.ps from ad40020000g210170_1.pi
XSPEC 9.01 09:27:13 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad40020000g210170_1.pi
Net count rate (cts/s) for file 1 6.950 +/- 1.4601E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad40020000g310170_1_pi.ps from ad40020000g310170_1.pi
XSPEC 9.01 09:27:27 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad40020000g310170_1.pi
Net count rate (cts/s) for file 1 9.444 +/- 1.7020E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad40020000s010102_1_pi.ps from ad40020000s010102_1.pi
XSPEC 9.01 09:27:41 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad40020000s010102_1.pi
Net count rate (cts/s) for file 1 8.783 +/- 1.6876E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad40020000s110102_1_pi.ps from ad40020000s110102_1.pi
XSPEC 9.01 09:27:55 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad40020000s110102_1.pi
Net count rate (cts/s) for file 1 7.452 +/- 1.5596E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
5 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.48E+03 3427 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 89867 10256 0 0 0
Writing events file
89867 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 3272 252 0 0 0
Writing events file
93139 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 112723 12586 0 0 0
Writing events file
205862 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 61859 7094 0 0 0
Writing events file
267721 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 3181 246 0 0 0
Writing events file
270902 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
301336 270902 30434 0 0 0
in 30842.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000202l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > read events ad40020000s000602l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad40020000s000002_1.lc with binsize 5.69249657811175
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.31E+05 270902 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/events.tmp
Total Good Bad: Region Time Phase Cut
270902 270902 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
270902 270902 0 0 0 0
in 30842.17 seconds
Fits light curve has 270902 counts for 8.783 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > set binsize 5.69249657811175
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad40020000s000002_1.lc
Wrote FITS light curve to file ad40020000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad40020000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad40020000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ EXO2030+375 Start Time (d) .... 9169 04:42:24.334
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9170 03:15:26.240
No. of Rows ....... 5416 Bin Time (s) ...... 5.692
Right Ascension ... 3.0803E+02 Internal time sys.. Converted to TJD
Declination ....... 3.7747E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 158.744 (s)
Intv 1 Start 9169 4:43:43
Ser.1 Avg 8.756 Chisq 4197. Var 2.279 Newbs. 220
Min 4.128 Max 16.20 expVar 0.1016 Bins 5416
Results from Statistical Analysis
Newbin Integration Time (s).. 158.74
Interval Duration (s)........ 81118.
No. of Newbins .............. 220
Average (c/s) ............... 8.7563 +/- 0.22E-01
Standard Deviation (c/s)..... 1.5097
Minimum (c/s)................ 4.1282
Maximum (c/s)................ 16.197
Variance ((c/s)**2).......... 2.2793 +/- 0.22
Expected Variance ((c/s)**2). 0.10159 +/- 0.97E-02
Third Moment ((c/s)**3)...... 3.3589
Average Deviation (c/s)...... 1.1226
Skewness..................... 0.97608 +/- 0.17
Kurtosis..................... 2.9109 +/- 0.33
RMS fractional variation..... 0.16853 +/- 0.84E-02
Chi-Square................... 4196.7 dof 219
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.11911E-42 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 158.744 (s)
Intv 1 Start 9169 4:43:43
Ser.1 Avg 8.756 Chisq 4197. Var 2.279 Newbs. 220
Min 4.128 Max 16.20 expVar 0.1016 Bins 5416
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=4.0000000000E+00 for ad40020000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
2 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
3 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
4 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
5 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.45E+03 2936 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 75083 6847 0 0 0
Writing events file
75083 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 2357 146 0 0 0
Writing events file
77440 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 95772 8523 0 0 0
Writing events file
173212 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 52823 4913 0 0 0
Writing events file
226035 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 2758 178 0 0 0
Writing events file
228793 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
249400 228793 20607 0 0 0
in 30638.70 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100202l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > read events ad40020000s100602l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad40020000s100002_1.lc with binsize 6.69572533208964
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.31E+05 228793 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/events.tmp
Total Good Bad: Region Time Phase Cut
228793 228793 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
228793 228793 0 0 0 0
in 30638.70 seconds
Fits light curve has 228793 counts for 7.467 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > set binsize 6.69572533208964
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad40020000s100002_1.lc
Wrote FITS light curve to file ad40020000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad40020000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad40020000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ EXO2030+375 Start Time (d) .... 9169 04:42:24.334
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9170 03:14:54.240
No. of Rows ....... 4583 Bin Time (s) ...... 6.696
Right Ascension ... 3.0803E+02 Internal time sys.. Converted to TJD
Declination ....... 3.7747E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 158.682 (s)
Intv 1 Start 9169 4:43:43
Ser.1 Avg 7.441 Chisq 4434. Var 1.306 Newbs. 219
Min 4.901 Max 11.26 expVar 0.6316E-01 Bins 4583
Results from Statistical Analysis
Newbin Integration Time (s).. 158.68
Interval Duration (s)........ 81086.
No. of Newbins .............. 219
Average (c/s) ............... 7.4405 +/- 0.17E-01
Standard Deviation (c/s)..... 1.1427
Minimum (c/s)................ 4.9012
Maximum (c/s)................ 11.263
Variance ((c/s)**2).......... 1.3058 +/- 0.13
Expected Variance ((c/s)**2). 0.63164E-01 +/- 0.61E-02
Third Moment ((c/s)**3)...... 1.0304
Average Deviation (c/s)...... 0.89499
Skewness..................... 0.69056 +/- 0.17
Kurtosis..................... 0.63296 +/- 0.33
RMS fractional variation..... 0.14982 +/- 0.75E-02
Chi-Square................... 4433.8 dof 218
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 158.682 (s)
Intv 1 Start 9169 4:43:43
Ser.1 Avg 7.441 Chisq 4434. Var 1.306 Newbs. 219
Min 4.901 Max 11.26 expVar 0.6316E-01 Bins 4583
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=6.2500000000E-02 for ad40020000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
4 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 329 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 66759 16576 0 0 0
Writing events file
66759 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 102344 25093 0 0 0
Writing events file
169103 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 57231 14164 0 0 0
Writing events file
226334 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 256 73 0 0 0
Writing events file
226590 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
282496 226590 55906 0 0 0
in 32603.60 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad40020000g200070_1.lc with binsize 7.19440478989935
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.33E+05 226590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/events.tmp
Total Good Bad: Region Time Phase Cut
226590 226590 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
226590 226590 0 0 0 0
in 32603.60 seconds
Fits light curve has 226590 counts for 6.950 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > set binsize 7.19440478989935
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad40020000g200070_1.lc
Wrote FITS light curve to file ad40020000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad40020000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad40020000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ EXO2030+375 Start Time (d) .... 9169 04:42:34.334
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9170 04:20:30.240
No. of Rows ....... 4531 Bin Time (s) ...... 7.194
Right Ascension ... 3.0803E+02 Internal time sys.. Converted to TJD
Declination ....... 3.7747E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 166.359 (s)
Intv 1 Start 9169 4:43:57
Ser.1 Avg 6.861 Chisq 3675. Var 1.397 Newbs. 226
Min 2.238 Max 10.50 expVar 0.8094E-01 Bins 4531
Results from Statistical Analysis
Newbin Integration Time (s).. 166.36
Interval Duration (s)........ 85009.
No. of Newbins .............. 226
Average (c/s) ............... 6.8609 +/- 0.19E-01
Standard Deviation (c/s)..... 1.1818
Minimum (c/s)................ 2.2379
Maximum (c/s)................ 10.500
Variance ((c/s)**2).......... 1.3967 +/- 0.13
Expected Variance ((c/s)**2). 0.80939E-01 +/- 0.76E-02
Third Moment ((c/s)**3)......-0.34930
Average Deviation (c/s)...... 0.90587
Skewness.....................-0.21162 +/- 0.16
Kurtosis..................... 1.3079 +/- 0.33
RMS fractional variation..... 0.16719 +/- 0.84E-02
Chi-Square................... 3675.1 dof 225
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.10650E-42 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 166.359 (s)
Intv 1 Start 9169 4:43:57
Ser.1 Avg 6.861 Chisq 3675. Var 1.397 Newbs. 226
Min 2.238 Max 10.50 expVar 0.8094E-01 Bins 4531
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=6.2500000000E-02 for ad40020000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
2 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
3 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
4 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 350 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 91535 17674 0 0 0
Writing events file
91535 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 140037 26878 0 0 0
Writing events file
231572 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 76035 14860 0 0 0
Writing events file
307607 events written to the output file
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 288 62 0 0 0
Writing events file
307895 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
367369 307895 59474 0 0 0
in 32601.60 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad40020000g300070_1.lc with binsize 5.29427298801342
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.33E+05 307895 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/events.tmp
Total Good Bad: Region Time Phase Cut
307895 307895 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
307895 307895 0 0 0 0
in 32601.60 seconds
Fits light curve has 307895 counts for 9.444 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > set binsize 5.29427298801342
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad40020000g300070_1.lc
Wrote FITS light curve to file ad40020000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad40020000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad40020000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ EXO2030+375 Start Time (d) .... 9169 04:42:34.334
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9170 04:20:30.240
No. of Rows ....... 6158 Bin Time (s) ...... 5.294
Right Ascension ... 3.0803E+02 Internal time sys.. Converted to TJD
Declination ....... 3.7747E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 166.359 (s)
Intv 1 Start 9169 4:43:57
Ser.1 Avg 9.361 Chisq 4557. Var 3.086 Newbs. 227
Min 2.644 Max 17.94 expVar 0.1180 Bins 6158
Results from Statistical Analysis
Newbin Integration Time (s).. 166.36
Interval Duration (s)........ 85009.
No. of Newbins .............. 227
Average (c/s) ............... 9.3613 +/- 0.23E-01
Standard Deviation (c/s)..... 1.7568
Minimum (c/s)................ 2.6444
Maximum (c/s)................ 17.944
Variance ((c/s)**2).......... 3.0862 +/- 0.29
Expected Variance ((c/s)**2). 0.11800 +/- 0.11E-01
Third Moment ((c/s)**3)...... 0.92638
Average Deviation (c/s)...... 1.2573
Skewness..................... 0.17086 +/- 0.16
Kurtosis..................... 3.7787 +/- 0.33
RMS fractional variation..... 0.18404 +/- 0.90E-02
Chi-Square................... 4557.0 dof 226
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 166.359 (s)
Intv 1 Start 9169 4:43:57
Ser.1 Avg 9.361 Chisq 4557. Var 3.086 Newbs. 227
Min 2.644 Max 17.94 expVar 0.1180 Bins 6158
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> Merging GTIs from the following files:
ad40020000g200170h.evt[2] ad40020000g200370h.evt[2] ad40020000g200470m.evt[2] ad40020000g200570l.evt[2]-> Making L1 light curve of ft930701_0242_1244G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 56302 output records from 56325 good input G2_L1 records.-> Making L1 light curve of ft930701_0242_1244G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 9774 output records from 56325 good input G2_L1 records.-> Making L1 light curve of ft930701_1244_0420G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 84215 output records from 84233 good input G2_L1 records.-> Making L1 light curve of ft930701_1244_0420G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 22674 output records from 92709 good input G2_L1 records.-> Merging GTIs from the following files:
ad40020000g300170h.evt[2] ad40020000g300370h.evt[2] ad40020000g300470m.evt[2] ad40020000g300570l.evt[2]-> Making L1 light curve of ft930701_0242_1244G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 61567 output records from 61590 good input G3_L1 records.-> Making L1 light curve of ft930701_0242_1244G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 9774 output records from 61590 good input G3_L1 records.-> Making L1 light curve of ft930701_1244_0420G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 91172 output records from 91190 good input G3_L1 records.-> Making L1 light curve of ft930701_1244_0420G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 22678 output records from 99668 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 83335 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.evt
Total Good Bad: Region Time Phase Cut
83335 66759 16576 0 0 0
Writing events file
66759 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83335 66759 16576 0 0 0
in 9793.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad40020000g200170h_1.ulc use_events=yes
Wrote events list to file ad40020000g200170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g200370h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 127437 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.evt
Total Good Bad: Region Time Phase Cut
127437 102344 25093 0 0 0
Writing events file
102344 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
127437 102344 25093 0 0 0
in 14233.62 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad40020000g200370h_1.ulc use_events=yes
Wrote events list to file ad40020000g200370h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g200470m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 71395 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.evt
Total Good Bad: Region Time Phase Cut
71395 57231 14164 0 0 0
Writing events file
57231 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
71395 57231 14164 0 0 0
in 8479.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad40020000g200470m_1.ulc use_events=yes
Wrote events list to file ad40020000g200470m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g200570l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 329 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.evt
Total Good Bad: Region Time Phase Cut
329 256 73 0 0 0
Writing events file
256 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
329 256 73 0 0 0
in 96.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200570l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region ad40020000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad40020000g200570l_1.ulc use_events=yes
Wrote events list to file ad40020000g200570l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.98E+04 109209 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.evt
Total Good Bad: Region Time Phase Cut
109209 91535 17674 0 0 0
Writing events file
91535 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
109209 91535 17674 0 0 0
in 9793.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad40020000g300170h_1.ulc use_events=yes
Wrote events list to file ad40020000g300170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g300370h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.14E+05 166915 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.evt
Total Good Bad: Region Time Phase Cut
166915 140037 26878 0 0 0
Writing events file
140037 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
166915 140037 26878 0 0 0
in 14231.62 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad40020000g300370h_1.ulc use_events=yes
Wrote events list to file ad40020000g300370h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g300470m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.85E+04 90895 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.evt
Total Good Bad: Region Time Phase Cut
90895 76035 14860 0 0 0
Writing events file
76035 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
90895 76035 14860 0 0 0
in 8479.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300470m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad40020000g300470m_1.ulc use_events=yes
Wrote events list to file ad40020000g300470m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000g300570l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.96E+02 350 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.evt
Total Good Bad: Region Time Phase Cut
350 288 62 0 0 0
Writing events file
288 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
350 288 62 0 0 0
in 96.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300570l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region ad40020000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad40020000g300570l_1.ulc use_events=yes
Wrote events list to file ad40020000g300570l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad40020000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 100123 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000102h.evt
Total Good Bad: Region Time Phase Cut
100123 89867 10256 0 0 0
Writing events file
89867 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100123 89867 10256 0 0 0
in 10195.39 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad40020000s000102h_1.ulc use_events=yes
Wrote events list to file ad40020000s000102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s000202l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.48E+03 3524 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000202l.evt
Total Good Bad: Region Time Phase Cut
3524 3272 252 0 0 0
Writing events file
3272 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3524 3272 252 0 0 0
in 480.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000202l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad40020000s000202l_1.ulc use_events=yes
Wrote events list to file ad40020000s000202l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s000402h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.13E+05 125309 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000402h.evt
Total Good Bad: Region Time Phase Cut
125309 112723 12586 0 0 0
Writing events file
112723 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125309 112723 12586 0 0 0
in 12523.44 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000402h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad40020000s000402h_1.ulc use_events=yes
Wrote events list to file ad40020000s000402h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s000502m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.72E+04 68953 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000502m.evt
Total Good Bad: Region Time Phase Cut
68953 61859 7094 0 0 0
Writing events file
61859 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68953 61859 7094 0 0 0
in 7163.34 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000502m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad40020000s000502m_1.ulc use_events=yes
Wrote events list to file ad40020000s000502m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s000602l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.48E+03 3427 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s000602l.evt
Total Good Bad: Region Time Phase Cut
3427 3181 246 0 0 0
Writing events file
3181 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3427 3181 246 0 0 0
in 480.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s000602l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS0-BRIGHT > filter region ad40020000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad40020000s000602l_1.ulc use_events=yes
Wrote events list to file ad40020000s000602l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.10E+05 81930 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100102h.evt
Total Good Bad: Region Time Phase Cut
81930 75083 6847 0 0 0
Writing events file
75083 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
81930 75083 6847 0 0 0
in 10181.49 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad40020000s100102h_1.ulc use_events=yes
Wrote events list to file ad40020000s100102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s100202l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.38E+03 2503 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100202l.evt
Total Good Bad: Region Time Phase Cut
2503 2357 146 0 0 0
Writing events file
2357 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2503 2357 146 0 0 0
in 384.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100202l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad40020000s100202l_1.ulc use_events=yes
Wrote events list to file ad40020000s100202l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s100402h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.12E+05 104295 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100402h.evt
Total Good Bad: Region Time Phase Cut
104295 95772 8523 0 0 0
Writing events file
95772 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
104295 95772 8523 0 0 0
in 12487.48 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100402h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad40020000s100402h_1.ulc use_events=yes
Wrote events list to file ad40020000s100402h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s100502m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.71E+04 57736 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100502m.evt
Total Good Bad: Region Time Phase Cut
57736 52823 4913 0 0 0
Writing events file
52823 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57736 52823 4913 0 0 0
in 7137.73 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad40020000s100502m_1.ulc use_events=yes
Wrote events list to file ad40020000s100502m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad40020000s100602l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.45E+03 2936 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000s100602l.evt
Total Good Bad: Region Time Phase Cut
2936 2758 178 0 0 0
Writing events file
2758 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2936 2758 178 0 0 0
in 448.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000s100602l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-SIS1-BRIGHT > filter region ad40020000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad40020000s100602l_1.ulc use_events=yes
Wrote events list to file ad40020000s100602l_1.ulc
Changing Data directory from:
/data/data24/seq_proc/40020000.013/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 11048 Total of 0 sets of frame data are extracted.-> Extracting frame mode data from ft930701_1244.0420
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 11088 Total of 0 sets of frame data are extracted.
1 ad40020000g200170h.unf 441229 1 ad40020000g200270m.unf 441229 1 ad40020000g200370h.unf 441229 1 ad40020000g200470m.unf 441229 1 ad40020000g200570l.unf 441229-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
4 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 100097 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
4 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 100097 1024
5 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 26016 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.unf
Total Good Bad: Region Time Phase Cut
139026 7407 131619 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200270m.unf
Total Good Bad: Region Time Phase Cut
3152 383 2769 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.unf
Total Good Bad: Region Time Phase Cut
172938 7093 165845 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.unf
Total Good Bad: Region Time Phase Cut
100097 4839 95258 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.unf
Total Good Bad: Region Time Phase Cut
26016 4248 21768 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
441229 23970 417259 0 0 0
in 67055.79 seconds
Spectrum has 23970 counts for 0.3575 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 67056. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200470m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > read events ad40020000g200570l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad40020000g220170.cal group=yes
Wrote spectrum to ad40020000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 09:54:56 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad40020000g220170.cal
Net count rate (cts/s) for file 1 0.3575 +/- 2.3091E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1153E+06 using 84 PHA bins.
Reduced chi-squared = 1.4485E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1062E+06 using 84 PHA bins.
Reduced chi-squared = 1.4182E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1062E+06 using 84 PHA bins.
Reduced chi-squared = 1.4003E+04
!XSPEC> renorm
Chi-Squared = 7652. using 84 PHA bins.
Reduced chi-squared = 96.86
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
5889.2 0 1.000 5.892 0.1116 0.1086
9.3765E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1930.4 0 1.000 5.858 0.1612 0.1703
8.2230E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
505.17 -1 1.000 5.902 0.1747 0.2425
5.4682E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
416.94 -2 1.000 5.929 0.1887 0.2651
4.0186E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.73 -3 1.000 5.922 0.1826 0.2621
4.3154E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.67 -4 1.000 5.923 0.1836 0.2629
4.2357E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.61 -5 1.000 5.923 0.1832 0.2627
4.2550E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.61 0 1.000 5.923 0.1832 0.2627
4.2542E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92307 +/- 0.35028E-02
3 3 2 gaussian/b Sigma 0.183239 +/- 0.37703E-02
4 4 2 gaussian/b norm 0.262688 +/- 0.25284E-02
5 2 3 gaussian/b LineE 6.52132 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.192270 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.254237E-02 +/- 0.17330E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 412.6 using 84 PHA bins.
Reduced chi-squared = 5.223
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad40020000g220170.cal peaks at 5.92307 +/- 0.0035028 keV1 ad40020000g300170h.unf 535786 1 ad40020000g300270m.unf 535786 1 ad40020000g300370h.unf 535786 1 ad40020000g300470m.unf 535786 1 ad40020000g300570l.unf 535786 1 ad40020000g300670l.unf 535786-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
4 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
4 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
5 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 25602 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
2 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
3 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
4 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
5 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 25602 1024
6 EXO2030+ PH LOW 01/07/93 18:10:14 0.26E+03 523 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.unf
Total Good Bad: Region Time Phase Cut
167616 6691 160925 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300270m.unf
Total Good Bad: Region Time Phase Cut
3239 387 2852 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.unf
Total Good Bad: Region Time Phase Cut
217108 6674 210434 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.unf
Total Good Bad: Region Time Phase Cut
121698 4405 117293 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.unf
Total Good Bad: Region Time Phase Cut
25602 3994 21608 0 0 0
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300670l.unf
Total Good Bad: Region Time Phase Cut
523 88 435 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
535786 22239 513547 0 0 0
in 67183.79 seconds
Spectrum has 22239 counts for 0.3310 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 67184. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad40020000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!xsel:ASCA > read events ad40020000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300470m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300570l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > read events ad40020000g300670l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad40020000g320170.cal group=yes
Wrote spectrum to ad40020000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 09:56:11 13-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad40020000g320170.cal
Net count rate (cts/s) for file 1 0.3310 +/- 2.2200E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1339E+06 using 84 PHA bins.
Reduced chi-squared = 1.4726E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1253E+06 using 84 PHA bins.
Reduced chi-squared = 1.4427E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1253E+06 using 84 PHA bins.
Reduced chi-squared = 1.4244E+04
!XSPEC> renorm
Chi-Squared = 6781. using 84 PHA bins.
Reduced chi-squared = 85.84
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
5219.8 0 1.000 5.894 0.1089 0.1062
9.2581E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
2191.6 0 1.000 5.875 0.1492 0.1598
8.0275E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
435.93 -1 1.000 5.948 0.1591 0.2308
4.7823E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
299.18 -2 1.000 5.971 0.1606 0.2550
3.5741E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
290.18 -3 1.000 5.963 0.1515 0.2517
3.9239E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
289.79 -4 1.000 5.965 0.1530 0.2527
3.8168E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
289.68 -5 1.000 5.964 0.1524 0.2524
3.8438E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
289.68 0 1.000 5.964 0.1524 0.2524
3.8437E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.96447 +/- 0.29602E-02
3 3 2 gaussian/b Sigma 0.152396 +/- 0.36515E-02
4 4 2 gaussian/b norm 0.252444 +/- 0.22892E-02
5 2 3 gaussian/b LineE 6.56691 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.159908 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.843663E-02 +/- 0.13972E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 289.7 using 84 PHA bins.
Reduced chi-squared = 3.667
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad40020000g320170.cal peaks at 5.96447 +/- 0.0029602 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.20E+05 135344 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000102h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.23E+04 14091 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000202l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000202l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 02:42:20 0.20E+03 1196 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000302m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:40 0.19E+05 175921 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000402h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000402h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.12E+05 105355 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000502m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000502m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.13E+05 24817 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s000602l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad40020000s000602l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 02:44:44 0.21E+05 133634 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100102h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 03:25:48 0.27E+04 15058 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100202l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100202l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 02:42:20 0.97E+03 1774 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100302m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT HIGH 01/07/93 12:45:36 0.19E+05 171318 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100402h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT MEDIUM 01/07/93 12:45:48 0.13E+05 104497 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100502m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 EXO2030+ BRIGHT LOW 01/07/93 13:37:00 0.15E+05 30120 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000s100602l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad40020000s100602l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad40020000g200170h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 139026 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200170h.unf
Total Good Bad: Region Time Phase Cut
139026 15516 0 123510 0 0
Writing events file
15516 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
139026 15516 0 123510 0 0
in 6546.39 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad40020000g200270m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200270m.unf
Total Good Bad: Region Time Phase Cut
3152 1975 0 1177 0 0
Writing events file
1975 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3152 1975 0 1177 0 0
in 783.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g200370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad40020000g200370h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 172938 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200370h.unf
Total Good Bad: Region Time Phase Cut
172938 7983 0 164955 0 0
Writing events file
7983 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172938 7983 0 164955 0 0
in 2492.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g200470m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 100097 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad40020000g200470m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 100097 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200470m.unf
Total Good Bad: Region Time Phase Cut
100097 7062 0 93035 0 0
Writing events file
7062 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
100097 7062 0 93035 0 0
in 3024.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g200570l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 26016 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad40020000g200570l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 26016 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g200570l.unf
Total Good Bad: Region Time Phase Cut
26016 22739 0 3277 0 0
Writing events file
22739 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26016 22739 0 3277 0 0
in 10071.99 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300170h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 02:44:54 0.21E+05 167616 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300170h.unf
Total Good Bad: Region Time Phase Cut
167616 15527 0 152089 0 0
Writing events file
15527 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
167616 15527 0 152089 0 0
in 6548.39 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300270m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 02:42:30 0.91E+03 3239 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300270m.unf
Total Good Bad: Region Time Phase Cut
3239 2017 0 1222 0 0
Writing events file
2017 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3239 2017 0 1222 0 0
in 783.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300370h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH HIGH 01/07/93 12:45:48 0.20E+05 217108 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300370h.unf
Total Good Bad: Region Time Phase Cut
217108 8135 0 208973 0 0
Writing events file
8135 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
217108 8135 0 208973 0 0
in 2492.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300470m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300470m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH MEDIUM 01/07/93 12:45:58 0.14E+05 121698 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300470m.unf
Total Good Bad: Region Time Phase Cut
121698 7343 0 114355 0 0
Writing events file
7343 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
121698 7343 0 114355 0 0
in 3024.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300570l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 25602 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300570l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300570l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 13:43:34 0.11E+05 25602 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300570l.unf
Total Good Bad: Region Time Phase Cut
25602 22568 0 3034 0 0
Writing events file
22568 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25602 22568 0 3034 0 0
in 10031.94 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300570l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad40020000g300670l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 18:10:14 0.26E+03 523 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad40020000g300670l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 EXO2030+ PH LOW 01/07/93 18:10:14 0.26E+03 523 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/40020000.013/ad40020000g300670l.unf
Total Good Bad: Region Time Phase Cut
523 336 0 187 0 0
Writing events file
336 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
523 336 0 187 0 0
in 175.86 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/40020000.013/
Setting mkf directory to /data/data24/seq_proc/40020000.013/
!earthevents:ASCA > read events ad40020000g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/40020000.013/
HK Directory is: /data/data24/seq_proc/40020000.013/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad40020000s000102h.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s000402h.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s000102h.unf
ad40020000s000302m.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s000502m.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s000302m.unf
ad40020000s000202l.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s000602l.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s000202l.unf
ad40020000s100102h.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s100402h.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s100102h.unf
ad40020000s100302m.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s100502m.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s100302m.unf
ad40020000s100202l.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000s100602l.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000s100202l.unf
ad40020000g200170h.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000g200370h.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000g200170h.unf
ad40020000g200270m.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000g200470m.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000g200270m.unf
ad40020000g300170h.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000g300370h.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000g300170h.unf
ad40020000g300270m.unf|TLM_FILE|ft930701_0242.1244|Name of input telemetry file ad40020000g300470m.unf|TLM_FILE|ft930701_1244.0420|Name of input telemetry file-> listing ad40020000g300270m.unf
ad40020000g300570l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad40020000g300670l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad40020000g300570l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad40020000g300670l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad40020000g300570l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad40020000g300670l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad40020000g300570l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad40020000g300670l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad40020000g300570l.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255) ad40020000g300670l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad40020000g300570l.unf|SP_B_F|224|Spread discri B for FLF method (0-255) ad40020000g300670l.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad40020000g300570l.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad40020000g300670l.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad40020000g300570l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad40020000g300670l.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)-> listing ad40020000g300570l.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files