Processing Job Log for Sequence 56004080, version 003

This is the complete and detailed record of how this sequence was processed.

The following information is also available:

Processing started (7:19:22)

Checking input files for validity (7:19:24)

-> Verifying the input files
-> FITS file ad56004080_input.cat exists
-> FITS file fa980911_1122.1920 exists
-> FITS file ft980911_1122.1920 exists
-> Calculating Observation start and end times
-> Fetching leapsec.fits from /aps/calibration
-> leapsec.fits is already present in the working directory
-> Observation begins 1.7966654E+08 = 1998-09-11 11:22:16
-> Observation ends 1.7969525E+08 = 1998-09-11 19:20:46

Determine nominal pointing (7:19:32)

-> Checking fa980911_1122.1920 for problems
-> Fetching asca_mean_1999-04-23.fits from /aps/calibration
-> stdout output from aspect

Spacecraft Euler Angles: Phi=-94.13089 Theta=120.02725 Psi=173.27362
Telescope pointing: R.A.=265.56236 Dec=-30.12895 Roll=83.11989 degrees

-> Nominal spacecraft Euler angles: Phi=-94.130893572259 Theta=120.02724801933 Psi=173.27362114236
-> Nominal telescope pointing: R.A.=265.56236213329 Dec=-30.128952686821 Roll Angle=83.119886694621
-> Galactic Coordinates: Lii=358.599928 Bii=-0.000750

Running frfread on telemetry files (7:19:44)

-> Running frfread on ft980911_1122.1920
-> stdout output from frfread4

79.9997 second gap between superframes 799 and 800
SIS0 peak error time=179670102.50154 x=323 y=43 ph0=2340 ph2=3615 ph5=2605
FAINT event CCD=0, but using exposure CCD=2 time=179670102.50154
SIS0 coordinate error time=179670102.50154 x=327 y=476 pha[0]=2824 chip=0
SIS0 peak error time=179670102.50154 x=327 y=476 ph0=2824 ph6=3052 ph7=3872
FAINT event CCD=0, but using exposure CCD=2 time=179670102.50154
Dropping SF 1145 with corrupted frame indicator
Dropping SF 1146 with corrupted frame indicator
SIS0 peak error time=179670110.50152 x=204 y=352 ph0=0 ph2=988 ph3=2640
FAINT event CCD=0, but using exposure CCD=2 time=179670110.50152
23.9999 second gap between superframes 1147 and 1148
1.99999 second gap between superframes 2136 and 2137
102 second gap between superframes 3098 and 3099
Warning: GIS2 bit assignment changed between 179675560.60916 and 179675562.60915
Warning: GIS3 bit assignment changed between 179675568.60913 and 179675570.60913
Warning: GIS2 bit assignment changed between 179675576.60911 and 179675578.6091
Warning: GIS3 bit assignment changed between 179675584.60908 and 179675586.60908
Dropping SF 3253 with inconsistent datamode 0/31
SIS0 peak error time=179675798.48338 x=413 y=186 ph0=612 ph6=2193 ph8=2844
Dropping SF 3262 with inconsistent datamode 0/9
SIS0 peak error time=179676190.48214 x=258 y=118 ph0=2481 ph2=2584 ph8=2752
FAINT event CCD=3, but using exposure CCD=2 time=179676190.48214
Dropping SF 3452 with inconsistent datamode 5/0
1.99999 second gap between superframes 4492 and 4493
93.9997 second gap between superframes 5431 and 5432
Warning: GIS2 bit assignment changed between 179681664.58968 and 179681666.58968
Warning: GIS3 bit assignment changed between 179681674.58965 and 179681676.58965
Warning: GIS2 bit assignment changed between 179681682.58963 and 179681684.58962
Warning: GIS3 bit assignment changed between 179681690.5896 and 179681692.5896
SIS0 peak error time=179682274.46274 x=63 y=80 ph0=0 ph6=3951 ph7=2321 ph8=1517
Dropping SF 5791 with corrupted frame indicator
Dropping SF 5792 with inconsistent datamode 0/31
7070 of 7077 super frames processed

-> 0% of superframes in ft980911_1122.1920 corrupted
-> Deleting the following files with NEVENTS=0

ft980911_1122_1920G200170M.fits
ft980911_1122_1920G200270H.fits
ft980911_1122_1920G200370H.fits
ft980911_1122_1920G200470H.fits
ft980911_1122_1920G200570H.fits
ft980911_1122_1920G200670H.fits
ft980911_1122_1920G201270H.fits
ft980911_1122_1920G201370M.fits
ft980911_1122_1920G201470M.fits
ft980911_1122_1920G201570H.fits
ft980911_1122_1920G201670H.fits
ft980911_1122_1920G201770H.fits
ft980911_1122_1920G201870H.fits
ft980911_1122_1920G202170H.fits
ft980911_1122_1920G202370H.fits
ft980911_1122_1920G202470H.fits
ft980911_1122_1920G202570H.fits
ft980911_1122_1920G203270H.fits
ft980911_1122_1920G203370H.fits
ft980911_1122_1920G203470M.fits
ft980911_1122_1920G203570M.fits
ft980911_1122_1920G203670H.fits
ft980911_1122_1920G203770H.fits
ft980911_1122_1920G203870H.fits
ft980911_1122_1920G203970H.fits
ft980911_1122_1920G204470H.fits
ft980911_1122_1920G204570H.fits
ft980911_1122_1920G204670H.fits
ft980911_1122_1920G204770H.fits
ft980911_1122_1920G204970H.fits
ft980911_1122_1920G205670L.fits
ft980911_1122_1920G205770H.fits
ft980911_1122_1920G206570H.fits
ft980911_1122_1920G206670H.fits
ft980911_1122_1920G206770L.fits
ft980911_1122_1920G206870L.fits
ft980911_1122_1920G206970M.fits
ft980911_1122_1920G300170M.fits
ft980911_1122_1920G300270H.fits
ft980911_1122_1920G300370H.fits
ft980911_1122_1920G300470H.fits
ft980911_1122_1920G300570H.fits
ft980911_1122_1920G300670H.fits
ft980911_1122_1920G301170H.fits
ft980911_1122_1920G301270H.fits
ft980911_1122_1920G301370M.fits
ft980911_1122_1920G301470M.fits
ft980911_1122_1920G301570H.fits
ft980911_1122_1920G301670H.fits
ft980911_1122_1920G301770H.fits
ft980911_1122_1920G301870H.fits
ft980911_1122_1920G301970H.fits
ft980911_1122_1920G302470H.fits
ft980911_1122_1920G302570H.fits
ft980911_1122_1920G302670H.fits
ft980911_1122_1920G302770H.fits
ft980911_1122_1920G303370H.fits
ft980911_1122_1920G303470M.fits
ft980911_1122_1920G303570M.fits
ft980911_1122_1920G303670H.fits
ft980911_1122_1920G303770H.fits
ft980911_1122_1920G303870H.fits
ft980911_1122_1920G303970H.fits
ft980911_1122_1920G304070H.fits
ft980911_1122_1920G304170H.fits
ft980911_1122_1920G304570H.fits
ft980911_1122_1920G304670H.fits
ft980911_1122_1920G304770H.fits
ft980911_1122_1920G304870H.fits
ft980911_1122_1920G304970H.fits
ft980911_1122_1920G305370L.fits
ft980911_1122_1920G305470H.fits
ft980911_1122_1920G305570H.fits
ft980911_1122_1920G306270H.fits
ft980911_1122_1920G306370H.fits
ft980911_1122_1920G306470L.fits
ft980911_1122_1920G306570L.fits
ft980911_1122_1920G306670M.fits
ft980911_1122_1920S000101M.fits
ft980911_1122_1920S000201M.fits
ft980911_1122_1920S000901M.fits
ft980911_1122_1920S001501M.fits
ft980911_1122_1920S100101M.fits

-> merging GTIs for s0 980911_1122.1920
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980911_1122_1920S0HK.fits
-> Total ONTIME for s0 980911_1122.1920 = 23847.9
-> merging GTIs for s1 980911_1122.1920
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980911_1122_1920S1HK.fits
-> Total ONTIME for s1 980911_1122.1920 = 25599.9
-> merging GTIs for g2 980911_1122.1920
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980911_1122_1920G2HK.fits
-> Total ONTIME for g2 980911_1122.1920 = 18729.9
-> merging GTIs for g3 980911_1122.1920
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980911_1122_1920G3HK.fits
-> Total ONTIME for g3 980911_1122.1920 = 18719.9

Merging event files from frfread (7:24:24)

-> Grouping s0 event files
-> stdout output from group_event_files

1 ft980911_1122_1920S000601H.fits 85689
1 ft980911_1122_1920S001201H.fits 85689
1 ft980911_1122_1920S002601H.fits 85689
2 ft980911_1122_1920S000401H.fits 24468
2 ft980911_1122_1920S000501H.fits 24468
2 ft980911_1122_1920S001101H.fits 24468
2 ft980911_1122_1920S001701H.fits 24468
2 ft980911_1122_1920S002201H.fits 24468
2 ft980911_1122_1920S002701H.fits 24468
2 ft980911_1122_1920S003201H.fits 24468
3 ft980911_1122_1920S000301M.fits 8940
3 ft980911_1122_1920S001001M.fits 8940
3 ft980911_1122_1920S001601M.fits 8940
3 ft980911_1122_1920S002301M.fits 8940
3 ft980911_1122_1920S003101M.fits 8940
3 ft980911_1122_1920S003301M.fits 8940
4 ft980911_1122_1920S001801L.fits 5299
4 ft980911_1122_1920S002401L.fits 5299
4 ft980911_1122_1920S003001L.fits 5299
4 ft980911_1122_1920S003401L.fits 5299
5 ft980911_1122_1920S001901L.fits 4472
5 ft980911_1122_1920S002501L.fits 4472
5 ft980911_1122_1920S003501L.fits 4472
6 ft980911_1122_1920S000701M.fits 2048
6 ft980911_1122_1920S001301M.fits 2048
6 ft980911_1122_1920S003601M.fits 2048
7 ft980911_1122_1920S002101L.fits 128
7 ft980911_1122_1920S002901L.fits 128
8 ft980911_1122_1920S000801M.fits 59
8 ft980911_1122_1920S001401M.fits 59
9 ft980911_1122_1920S002001L.fits 3
10 ft980911_1122_1920S002801H.fits 1

-> Creating ad56004080s000101h.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 3 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S000601H.fits 
 2 -- ft980911_1122_1920S001201H.fits 
 3 -- ft980911_1122_1920S002601H.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S000601H.fits 
 2 -- ft980911_1122_1920S001201H.fits 
 3 -- ft980911_1122_1920S002601H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s000201h.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  7  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 7 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S000401H.fits 
 2 -- ft980911_1122_1920S000501H.fits 
 3 -- ft980911_1122_1920S001101H.fits 
 4 -- ft980911_1122_1920S001701H.fits 
 5 -- ft980911_1122_1920S002201H.fits 
 6 -- ft980911_1122_1920S002701H.fits 
 7 -- ft980911_1122_1920S003201H.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S000401H.fits 
 2 -- ft980911_1122_1920S000501H.fits 
 3 -- ft980911_1122_1920S001101H.fits 
 4 -- ft980911_1122_1920S001701H.fits 
 5 -- ft980911_1122_1920S002201H.fits 
 6 -- ft980911_1122_1920S002701H.fits 
 7 -- ft980911_1122_1920S003201H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s000301m.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  6  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 6 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S000301M.fits 
 2 -- ft980911_1122_1920S001001M.fits 
 3 -- ft980911_1122_1920S001601M.fits 
 4 -- ft980911_1122_1920S002301M.fits 
 5 -- ft980911_1122_1920S003101M.fits 
 6 -- ft980911_1122_1920S003301M.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S000301M.fits 
 2 -- ft980911_1122_1920S001001M.fits 
 3 -- ft980911_1122_1920S001601M.fits 
 4 -- ft980911_1122_1920S002301M.fits 
 5 -- ft980911_1122_1920S003101M.fits 
 6 -- ft980911_1122_1920S003301M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s000401l.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 4 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S001801L.fits 
 2 -- ft980911_1122_1920S002401L.fits 
 3 -- ft980911_1122_1920S003001L.fits 
 4 -- ft980911_1122_1920S003401L.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S001801L.fits 
 2 -- ft980911_1122_1920S002401L.fits 
 3 -- ft980911_1122_1920S003001L.fits 
 4 -- ft980911_1122_1920S003401L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s000501l.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 3 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S001901L.fits 
 2 -- ft980911_1122_1920S002501L.fits 
 3 -- ft980911_1122_1920S003501L.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S001901L.fits 
 2 -- ft980911_1122_1920S002501L.fits 
 3 -- ft980911_1122_1920S003501L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s000601m.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 3 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S000701M.fits 
 2 -- ft980911_1122_1920S001301M.fits 
 3 -- ft980911_1122_1920S003601M.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S000701M.fits 
 2 -- ft980911_1122_1920S001301M.fits 
 3 -- ft980911_1122_1920S003601M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Ignoring the following files containing 128 events ft980911_1122_1920S002101L.fits ft980911_1122_1920S002901L.fits
-> Ignoring the following files containing 59 events ft980911_1122_1920S000801M.fits ft980911_1122_1920S001401M.fits
-> Ignoring the following files containing 3 events ft980911_1122_1920S002001L.fits
-> Ignoring the following files containing 1 events ft980911_1122_1920S002801H.fits
-> Grouping s1 event files
-> stdout output from group_event_files

1 ft980911_1122_1920S100301H.fits 116770
1 ft980911_1122_1920S100401H.fits 116770
1 ft980911_1122_1920S100801H.fits 116770
1 ft980911_1122_1920S101201H.fits 116770
1 ft980911_1122_1920S101501H.fits 116770
1 ft980911_1122_1920S101801H.fits 116770
1 ft980911_1122_1920S102301H.fits 116770
2 ft980911_1122_1920S100201M.fits 17508
2 ft980911_1122_1920S100501M.fits 17508
2 ft980911_1122_1920S100701M.fits 17508
2 ft980911_1122_1920S100901M.fits 17508
2 ft980911_1122_1920S101101M.fits 17508
2 ft980911_1122_1920S101601M.fits 17508
2 ft980911_1122_1920S102201M.fits 17508
2 ft980911_1122_1920S102401M.fits 17508
2 ft980911_1122_1920S102601M.fits 17508
3 ft980911_1122_1920S101301L.fits 11136
3 ft980911_1122_1920S101701L.fits 11136
3 ft980911_1122_1920S102101L.fits 11136
3 ft980911_1122_1920S102501L.fits 11136
4 ft980911_1122_1920S101401L.fits 136
4 ft980911_1122_1920S102001L.fits 136
5 ft980911_1122_1920S100601M.fits 64
5 ft980911_1122_1920S101001M.fits 64
6 ft980911_1122_1920S101901H.fits 17

-> Creating ad56004080s100101h.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  7  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 7 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S100301H.fits 
 2 -- ft980911_1122_1920S100401H.fits 
 3 -- ft980911_1122_1920S100801H.fits 
 4 -- ft980911_1122_1920S101201H.fits 
 5 -- ft980911_1122_1920S101501H.fits 
 6 -- ft980911_1122_1920S101801H.fits 
 7 -- ft980911_1122_1920S102301H.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S100301H.fits 
 2 -- ft980911_1122_1920S100401H.fits 
 3 -- ft980911_1122_1920S100801H.fits 
 4 -- ft980911_1122_1920S101201H.fits 
 5 -- ft980911_1122_1920S101501H.fits 
 6 -- ft980911_1122_1920S101801H.fits 
 7 -- ft980911_1122_1920S102301H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s100201m.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  9  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 9 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S100201M.fits 
 2 -- ft980911_1122_1920S100501M.fits 
 3 -- ft980911_1122_1920S100701M.fits 
 4 -- ft980911_1122_1920S100901M.fits 
 5 -- ft980911_1122_1920S101101M.fits 
 6 -- ft980911_1122_1920S101601M.fits 
 7 -- ft980911_1122_1920S102201M.fits 
 8 -- ft980911_1122_1920S102401M.fits 
 9 -- ft980911_1122_1920S102601M.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S100201M.fits 
 2 -- ft980911_1122_1920S100501M.fits 
 3 -- ft980911_1122_1920S100701M.fits 
 4 -- ft980911_1122_1920S100901M.fits 
 5 -- ft980911_1122_1920S101101M.fits 
 6 -- ft980911_1122_1920S101601M.fits 
 7 -- ft980911_1122_1920S102201M.fits 
 8 -- ft980911_1122_1920S102401M.fits 
 9 -- ft980911_1122_1920S102601M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080s100301l.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 4 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920S101301L.fits 
 2 -- ft980911_1122_1920S101701L.fits 
 3 -- ft980911_1122_1920S102101L.fits 
 4 -- ft980911_1122_1920S102501L.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920S101301L.fits 
 2 -- ft980911_1122_1920S101701L.fits 
 3 -- ft980911_1122_1920S102101L.fits 
 4 -- ft980911_1122_1920S102501L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Ignoring the following files containing 136 events ft980911_1122_1920S101401L.fits ft980911_1122_1920S102001L.fits
-> Ignoring the following files containing 64 events ft980911_1122_1920S100601M.fits ft980911_1122_1920S101001M.fits
-> Ignoring the following files containing 17 events ft980911_1122_1920S101901H.fits
-> Grouping g2 event files
-> stdout output from group_event_files

1 ft980911_1122_1920G200970H.fits 15805
1 ft980911_1122_1920G201070H.fits 15805
1 ft980911_1122_1920G202270H.fits 15805
1 ft980911_1122_1920G202970H.fits 15805
1 ft980911_1122_1920G203070H.fits 15805
1 ft980911_1122_1920G203170H.fits 15805
1 ft980911_1122_1920G204370H.fits 15805
1 ft980911_1122_1920G205270H.fits 15805
1 ft980911_1122_1920G205470H.fits 15805
1 ft980911_1122_1920G206170H.fits 15805
1 ft980911_1122_1920G206470H.fits 15805
1 ft980911_1122_1920G207270H.fits 15805
2 ft980911_1122_1920G205570L.fits 7859
2 ft980911_1122_1920G206370L.fits 7859
2 ft980911_1122_1920G207570L.fits 7859
3 ft980911_1122_1920G206270M.fits 4819
3 ft980911_1122_1920G207170M.fits 4819
3 ft980911_1122_1920G207370M.fits 4819
3 ft980911_1122_1920G207970M.fits 4819
4 ft980911_1122_1920G207470L.fits 76
5 ft980911_1122_1920G207770M.fits 51
6 ft980911_1122_1920G207870M.fits 48
7 ft980911_1122_1920G207670M.fits 34
8 ft980911_1122_1920G207070M.fits 18
9 ft980911_1122_1920G202770H.fits 16
9 ft980911_1122_1920G205070H.fits 16
10 ft980911_1122_1920G200770H.fits 8
10 ft980911_1122_1920G202070H.fits 8
10 ft980911_1122_1920G204170H.fits 8
10 ft980911_1122_1920G205970H.fits 8
11 ft980911_1122_1920G202870H.fits 5
11 ft980911_1122_1920G205170H.fits 5
12 ft980911_1122_1920G200870H.fits 4
12 ft980911_1122_1920G204270H.fits 4
12 ft980911_1122_1920G206070H.fits 4
13 ft980911_1122_1920G201970H.fits 3
13 ft980911_1122_1920G204070H.fits 3
13 ft980911_1122_1920G205870H.fits 3
14 ft980911_1122_1920G202670H.fits 3
15 ft980911_1122_1920G205370H.fits 2
16 ft980911_1122_1920G201170H.fits 1
17 ft980911_1122_1920G204870H.fits 1

-> Creating ad56004080g200170h.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  12  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 12 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G200970H.fits 
 2 -- ft980911_1122_1920G201070H.fits 
 3 -- ft980911_1122_1920G202270H.fits 
 4 -- ft980911_1122_1920G202970H.fits 
 5 -- ft980911_1122_1920G203070H.fits 
 6 -- ft980911_1122_1920G203170H.fits 
 7 -- ft980911_1122_1920G204370H.fits 
 8 -- ft980911_1122_1920G205270H.fits 
 9 -- ft980911_1122_1920G205470H.fits 
 10 -- ft980911_1122_1920G206170H.fits 
 11 -- ft980911_1122_1920G206470H.fits 
 12 -- ft980911_1122_1920G207270H.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G200970H.fits 
 2 -- ft980911_1122_1920G201070H.fits 
 3 -- ft980911_1122_1920G202270H.fits 
 4 -- ft980911_1122_1920G202970H.fits 
 5 -- ft980911_1122_1920G203070H.fits 
 6 -- ft980911_1122_1920G203170H.fits 
 7 -- ft980911_1122_1920G204370H.fits 
 8 -- ft980911_1122_1920G205270H.fits 
 9 -- ft980911_1122_1920G205470H.fits 
 10 -- ft980911_1122_1920G206170H.fits 
 11 -- ft980911_1122_1920G206470H.fits 
 12 -- ft980911_1122_1920G207270H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080g200270l.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 3 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G205570L.fits 
 2 -- ft980911_1122_1920G206370L.fits 
 3 -- ft980911_1122_1920G207570L.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G205570L.fits 
 2 -- ft980911_1122_1920G206370L.fits 
 3 -- ft980911_1122_1920G207570L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080g200370m.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 4 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G206270M.fits 
 2 -- ft980911_1122_1920G207170M.fits 
 3 -- ft980911_1122_1920G207370M.fits 
 4 -- ft980911_1122_1920G207970M.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G206270M.fits 
 2 -- ft980911_1122_1920G207170M.fits 
 3 -- ft980911_1122_1920G207370M.fits 
 4 -- ft980911_1122_1920G207970M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Ignoring the following files containing 76 events ft980911_1122_1920G207470L.fits
-> Ignoring the following files containing 51 events ft980911_1122_1920G207770M.fits
-> Ignoring the following files containing 48 events ft980911_1122_1920G207870M.fits
-> Ignoring the following files containing 34 events ft980911_1122_1920G207670M.fits
-> Ignoring the following files containing 18 events ft980911_1122_1920G207070M.fits
-> Ignoring the following files containing 16 events ft980911_1122_1920G202770H.fits ft980911_1122_1920G205070H.fits
-> Ignoring the following files containing 8 events ft980911_1122_1920G200770H.fits ft980911_1122_1920G202070H.fits ft980911_1122_1920G204170H.fits ft980911_1122_1920G205970H.fits
-> Ignoring the following files containing 5 events ft980911_1122_1920G202870H.fits ft980911_1122_1920G205170H.fits
-> Ignoring the following files containing 4 events ft980911_1122_1920G200870H.fits ft980911_1122_1920G204270H.fits ft980911_1122_1920G206070H.fits
-> Ignoring the following files containing 3 events ft980911_1122_1920G201970H.fits ft980911_1122_1920G204070H.fits ft980911_1122_1920G205870H.fits
-> Ignoring the following files containing 3 events ft980911_1122_1920G202670H.fits
-> Ignoring the following files containing 2 events ft980911_1122_1920G205370H.fits
-> Ignoring the following files containing 1 events ft980911_1122_1920G201170H.fits
-> Ignoring the following files containing 1 events ft980911_1122_1920G204870H.fits
-> Grouping g3 event files
-> stdout output from group_event_files

1 ft980911_1122_1920G300970H.fits 15310
1 ft980911_1122_1920G301070H.fits 15310
1 ft980911_1122_1920G302270H.fits 15310
1 ft980911_1122_1920G302970H.fits 15310
1 ft980911_1122_1920G303070H.fits 15310
1 ft980911_1122_1920G303170H.fits 15310
1 ft980911_1122_1920G304370H.fits 15310
1 ft980911_1122_1920G305170H.fits 15310
1 ft980911_1122_1920G305870H.fits 15310
1 ft980911_1122_1920G306170H.fits 15310
1 ft980911_1122_1920G306970H.fits 15310
2 ft980911_1122_1920G305270L.fits 7784
2 ft980911_1122_1920G306070L.fits 7784
2 ft980911_1122_1920G307270L.fits 7784
3 ft980911_1122_1920G305970M.fits 4854
3 ft980911_1122_1920G306870M.fits 4854
3 ft980911_1122_1920G307070M.fits 4854
3 ft980911_1122_1920G307670M.fits 4854
4 ft980911_1122_1920G307170L.fits 66
5 ft980911_1122_1920G307370M.fits 55
6 ft980911_1122_1920G307470M.fits 41
7 ft980911_1122_1920G307570M.fits 41
8 ft980911_1122_1920G302370H.fits 29
8 ft980911_1122_1920G304470H.fits 29
9 ft980911_1122_1920G306770M.fits 19
10 ft980911_1122_1920G300870H.fits 10
10 ft980911_1122_1920G302170H.fits 10
10 ft980911_1122_1920G304270H.fits 10
10 ft980911_1122_1920G305770H.fits 10
11 ft980911_1122_1920G302870H.fits 7
12 ft980911_1122_1920G300770H.fits 5
12 ft980911_1122_1920G302070H.fits 5
12 ft980911_1122_1920G305670H.fits 5
13 ft980911_1122_1920G305070H.fits 3
14 ft980911_1122_1920G303270H.fits 1

-> Creating ad56004080g300170h.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  11  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 11 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G300970H.fits 
 2 -- ft980911_1122_1920G301070H.fits 
 3 -- ft980911_1122_1920G302270H.fits 
 4 -- ft980911_1122_1920G302970H.fits 
 5 -- ft980911_1122_1920G303070H.fits 
 6 -- ft980911_1122_1920G303170H.fits 
 7 -- ft980911_1122_1920G304370H.fits 
 8 -- ft980911_1122_1920G305170H.fits 
 9 -- ft980911_1122_1920G305870H.fits 
 10 -- ft980911_1122_1920G306170H.fits 
 11 -- ft980911_1122_1920G306970H.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G300970H.fits 
 2 -- ft980911_1122_1920G301070H.fits 
 3 -- ft980911_1122_1920G302270H.fits 
 4 -- ft980911_1122_1920G302970H.fits 
 5 -- ft980911_1122_1920G303070H.fits 
 6 -- ft980911_1122_1920G303170H.fits 
 7 -- ft980911_1122_1920G304370H.fits 
 8 -- ft980911_1122_1920G305170H.fits 
 9 -- ft980911_1122_1920G305870H.fits 
 10 -- ft980911_1122_1920G306170H.fits 
 11 -- ft980911_1122_1920G306970H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080g300270l.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 3 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G305270L.fits 
 2 -- ft980911_1122_1920G306070L.fits 
 3 -- ft980911_1122_1920G307270L.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G305270L.fits 
 2 -- ft980911_1122_1920G306070L.fits 
 3 -- ft980911_1122_1920G307270L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Creating ad56004080g300370m.unf
-> stdout output from cmerge

---- cmerge:  version 1.7 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 4 good fits files ...
Merging binary extension #: 1 
 1 -- ft980911_1122_1920G305970M.fits 
 2 -- ft980911_1122_1920G306870M.fits 
 3 -- ft980911_1122_1920G307070M.fits 
 4 -- ft980911_1122_1920G307670M.fits 
Merging binary extension #: 2 
 1 -- ft980911_1122_1920G305970M.fits 
 2 -- ft980911_1122_1920G306870M.fits 
 3 -- ft980911_1122_1920G307070M.fits 
 4 -- ft980911_1122_1920G307670M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!

-> Ignoring the following files containing 66 events ft980911_1122_1920G307170L.fits
-> Ignoring the following files containing 55 events ft980911_1122_1920G307370M.fits
-> Ignoring the following files containing 41 events ft980911_1122_1920G307470M.fits
-> Ignoring the following files containing 41 events ft980911_1122_1920G307570M.fits
-> Ignoring the following files containing 29 events ft980911_1122_1920G302370H.fits ft980911_1122_1920G304470H.fits
-> Ignoring the following files containing 19 events ft980911_1122_1920G306770M.fits
-> Ignoring the following files containing 10 events ft980911_1122_1920G300870H.fits ft980911_1122_1920G302170H.fits ft980911_1122_1920G304270H.fits ft980911_1122_1920G305770H.fits
-> Ignoring the following files containing 7 events ft980911_1122_1920G302870H.fits
-> Ignoring the following files containing 5 events ft980911_1122_1920G300770H.fits ft980911_1122_1920G302070H.fits ft980911_1122_1920G305670H.fits
-> Ignoring the following files containing 3 events ft980911_1122_1920G305070H.fits
-> Ignoring the following files containing 1 events ft980911_1122_1920G303270H.fits
-> stdout output from tar

a ft980911_1122_1920G200770H.fits 31K
a ft980911_1122_1920G200870H.fits 31K
a ft980911_1122_1920G201170H.fits 31K
a ft980911_1122_1920G201970H.fits 31K
a ft980911_1122_1920G202070H.fits 31K
a ft980911_1122_1920G202670H.fits 31K
a ft980911_1122_1920G202770H.fits 31K
a ft980911_1122_1920G202870H.fits 31K
a ft980911_1122_1920G204070H.fits 31K
a ft980911_1122_1920G204170H.fits 31K
a ft980911_1122_1920G204270H.fits 31K
a ft980911_1122_1920G204870H.fits 31K
a ft980911_1122_1920G205070H.fits 31K
a ft980911_1122_1920G205170H.fits 31K
a ft980911_1122_1920G205370H.fits 31K
a ft980911_1122_1920G205870H.fits 31K
a ft980911_1122_1920G205970H.fits 31K
a ft980911_1122_1920G206070H.fits 31K
a ft980911_1122_1920G207070M.fits 31K
a ft980911_1122_1920G207470L.fits 31K
a ft980911_1122_1920G207670M.fits 31K
a ft980911_1122_1920G207770M.fits 31K
a ft980911_1122_1920G207870M.fits 31K
a ft980911_1122_1920G300770H.fits 31K
a ft980911_1122_1920G300870H.fits 31K
a ft980911_1122_1920G302070H.fits 31K
a ft980911_1122_1920G302170H.fits 31K
a ft980911_1122_1920G302370H.fits 31K
a ft980911_1122_1920G302870H.fits 31K
a ft980911_1122_1920G303270H.fits 31K
a ft980911_1122_1920G304270H.fits 31K
a ft980911_1122_1920G304470H.fits 31K
a ft980911_1122_1920G305070H.fits 31K
a ft980911_1122_1920G305670H.fits 31K
a ft980911_1122_1920G305770H.fits 31K
a ft980911_1122_1920G306770M.fits 31K
a ft980911_1122_1920G307170L.fits 31K
a ft980911_1122_1920G307370M.fits 31K
a ft980911_1122_1920G307470M.fits 31K
a ft980911_1122_1920G307570M.fits 31K
a ft980911_1122_1920S000801M.fits 29K
a ft980911_1122_1920S001401M.fits 29K
a ft980911_1122_1920S002001L.fits 29K
a ft980911_1122_1920S002101L.fits 29K
a ft980911_1122_1920S002801H.fits 29K
a ft980911_1122_1920S002901L.fits 31K
a ft980911_1122_1920S100601M.fits 29K
a ft980911_1122_1920S101001M.fits 29K
a ft980911_1122_1920S101401L.fits 29K
a ft980911_1122_1920S101901H.fits 29K
a ft980911_1122_1920S102001L.fits 31K

Converting FAINT mode files to BRIGHT and BRIGHT2 modes (7:26:33)

-> Split threshold for SIS0=40, and SIS1=40
-> Fetching faintdfe.tbl
-> Calculating DFE values for ad56004080s000101h.unf with zerodef=1
-> Converting ad56004080s000101h.unf to ad56004080s000112h.unf
-> Calculating DFE values for ad56004080s000101h.unf with zerodef=2
-> Converting ad56004080s000101h.unf to ad56004080s000102h.unf
-> Calculating DFE values for ad56004080s000201h.unf with zerodef=1
-> Converting ad56004080s000201h.unf to ad56004080s000212h.unf
-> Calculating DFE values for ad56004080s000201h.unf with zerodef=2
-> Converting ad56004080s000201h.unf to ad56004080s000202h.unf
-> Calculating DFE values for ad56004080s000301m.unf with zerodef=1
-> Converting ad56004080s000301m.unf to ad56004080s000312m.unf
-> Calculating DFE values for ad56004080s000301m.unf with zerodef=2
-> Converting ad56004080s000301m.unf to ad56004080s000302m.unf
-> Calculating DFE values for ad56004080s000401l.unf with zerodef=1
-> Converting ad56004080s000401l.unf to ad56004080s000412l.unf
-> Calculating DFE values for ad56004080s000401l.unf with zerodef=2
-> Converting ad56004080s000401l.unf to ad56004080s000402l.unf
-> Calculating DFE values for ad56004080s000501l.unf with zerodef=1
-> Converting ad56004080s000501l.unf to ad56004080s000512l.unf
-> Removing ad56004080s000512l.unf since it only has 508 events
-> Calculating DFE values for ad56004080s000501l.unf with zerodef=2
-> Converting ad56004080s000501l.unf to ad56004080s000502l.unf
-> Removing ad56004080s000502l.unf since it only has 493 events
-> Calculating DFE values for ad56004080s000601m.unf with zerodef=1
-> Converting ad56004080s000601m.unf to ad56004080s000612m.unf
-> Removing ad56004080s000612m.unf since it only has 27 events
-> Calculating DFE values for ad56004080s000601m.unf with zerodef=2
-> Converting ad56004080s000601m.unf to ad56004080s000602m.unf
-> Removing ad56004080s000602m.unf since it only has 25 events
-> Calculating DFE values for ad56004080s100101h.unf with zerodef=1
-> Converting ad56004080s100101h.unf to ad56004080s100112h.unf
-> Calculating DFE values for ad56004080s100101h.unf with zerodef=2
-> Converting ad56004080s100101h.unf to ad56004080s100102h.unf
-> Calculating DFE values for ad56004080s100201m.unf with zerodef=1
-> Converting ad56004080s100201m.unf to ad56004080s100212m.unf
-> Calculating DFE values for ad56004080s100201m.unf with zerodef=2
-> Converting ad56004080s100201m.unf to ad56004080s100202m.unf
-> Calculating DFE values for ad56004080s100301l.unf with zerodef=1
-> Converting ad56004080s100301l.unf to ad56004080s100312l.unf
-> Calculating DFE values for ad56004080s100301l.unf with zerodef=2
-> Converting ad56004080s100301l.unf to ad56004080s100302l.unf

Calibrating the unfiltered event files (7:32:31)

-> Creating GIS gain history files
-> leapsec.fits is already present in the working directory
-> Fetching gis_temp2gain.fits from /aps/calibration
-> Creating Gain History File ft980911_1122_1920.ghf
-> stdout output from temp2gain

temp2gain V4.6
leapsec FITS data was successfully read

'ft980911_1122.1920' is successfully opened
Data Start Time is 179666540.64 (19980911 112216)
Time Margin 2.0 sec included
'ft980911_1122.1920' EOF detected, sf=7077
Data End Time is 179695248.55 (19980911 192044)
Gain History is written in ft980911_1122_1920.ghf

-> Generating attitude correction table ad56004080_003_bp4.txt
-> Extracting info from ft980911_1122_1920CMHK.fits
-> Running ascalin on all unfiltered event files
-> Preparing to run ascalin on ad56004080g200170h.unf
-> Fetching gis2_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad56004080g200170h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080g200270l.unf
-> gis2_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad56004080g200270l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080g200370m.unf
-> gis2_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad56004080g200370m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080g300170h.unf
-> Fetching gis3_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad56004080g300170h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080g300270l.unf
-> gis3_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad56004080g300270l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080g300370m.unf
-> gis3_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad56004080g300370m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000101h.unf
-> Fetching s0_teldef_ascalin.fits from /aps/calibration
-> Fetching sisph2pi_110397.fits from /aps/calibration
-> Running ascalin on ad56004080s000101h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000102h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000102h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000112h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000112h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000201h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000201h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000202h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000202h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000212h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000212h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000301m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000301m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000302m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000302m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000312m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000312m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000401l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000401l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000402l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000402l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000412l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000412l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000501l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000501l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s000601m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s000601m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100101h.unf
-> Fetching s1_teldef_ascalin.fits from /aps/calibration
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100101h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100102h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100102h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100112h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100112h.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100201m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100201m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100202m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100202m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100212m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100212m.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100301l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100301l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100302l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100302l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

-> Preparing to run ascalin on ad56004080s100312l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad56004080s100312l.unf
-> stdout output from ascalin

ASCALIN_V0.9v

Creating filter files (7:38:47)

-> leapsec.fits is already present in the working directory
-> Fetching rigidity.data.1.23 from /aps/calibration
-> Copying orbit file /aps/orbit/frf.orbit.251 to working directory
-> Creating ft980911_1122_1920.mkf
-> stdout output from mkfilter2

 
leapsec FITS data was successfully read

S0-HK file: ft980911_1122_1920S0HK.fits

S1-HK file: ft980911_1122_1920S1HK.fits

G2-HK file: ft980911_1122_1920G2HK.fits

G3-HK file: ft980911_1122_1920G3HK.fits

Date and time are: 1998-09-11 11:21:34  mjd=51067.473318

Orbit file name is frf.orbit.251

Epoch of Orbital Elements: 1998-09-07 20:00:00

Rigidity Data File: rigidity.data.1.23

Attitude FRF: fa980911_1122.1920

output FITS File: ft980911_1122_1920.mkf

mkfilter2: Warning, faQparam error: time= 1.796664466380e+08 outside range of attitude file

           Euler angles undefined for this bin

mkfilter2: Warning, faQparam error: time= 1.796664786380e+08 outside range of attitude file

           Euler angles undefined for this bin

mkfilter2: Warning, faQparam seek error for time= 1.796665426380e+08

           Euler angles undefined for this bin

Total 901 Data bins were processed.

-> Adding deadtime to ft980911_1122_1920.mkf
-> Adding ad56004080_s0.dfe to ft980911_1122_1920.mkf
-> Adding ad56004080_s1.dfe to ft980911_1122_1920.mkf
-> Plotting quantities from ft980911_1122_1920.mkf
-> Extracting telemetry corruption files

Cleaning and filtering the unfiltered event files (7:50:24)

-> Skipping ad56004080s000101h.unf because of mode
-> Filtering ad56004080s000102h.unf into ad56004080s000102h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   61.875200
 The mean of the selected column is                  20.625067
 The standard deviation of the selected column is    9.1815223
 The minimum of selected column is                   14.968799
 The maximum of selected column is                   31.218851
 The number of points used in calculation is                3

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   58.812690
 The mean of the selected column is                  19.604230
 The standard deviation of the selected column is    6.3495659
 The minimum of selected column is                   12.593791
 The maximum of selected column is                   24.968830
 The number of points used in calculation is                3

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<48.1 )&&
(S0_PIXL2>0.5 && S0_PIXL2<38.6 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.19E+04     1126 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
            831       124              0       707         0         0
 Writing events file
    124 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           831       124              0       707         0         0
   in  85.799     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          124
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               6          51
cleaning chip # 2
 Hot pixels & counts                   :               6          42
cleaning chip # 3
 
 Number of pixels rejected           :           12
 Number of (internal) image counts   :          124
 Number of image cts rejected (N, %) :           9375.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            6            6            0
 
 Image counts      :             0           72           52            0
 Image cts rejected:             0           51           42            0
 Image cts rej (%) :          0.00        70.83        80.77         0.00
 
    filtering data...
 
 Total counts      :             0           72           52            0
 Total cts rejected:             0           51           42            0
 Total cts rej (%) :          0.00        70.83        80.77         0.00
 
 Number of clean counts accepted  :           31
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           12
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad56004080s000102h.evt use_events=no
Wrote cleaned events file to ad56004080s000102h.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no

-> Filtering ad56004080s000112h.unf into ad56004080s000112h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   61.875200
 The mean of the selected column is                  20.625067
 The standard deviation of the selected column is    9.1815223
 The minimum of selected column is                   14.968799
 The maximum of selected column is                   31.218851
 The number of points used in calculation is                3

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   58.812690
 The mean of the selected column is                  19.604230
 The standard deviation of the selected column is    6.3495659
 The minimum of selected column is                   12.593791
 The maximum of selected column is                   24.968830
 The number of points used in calculation is                3

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<48.1 )&&
(S0_PIXL2>0.5 && S0_PIXL2<38.6 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  12:50:00    0.19E+04     1179 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000112h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
            881       132              0       749         0         0
 Writing events file
    132 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           881       132              0       749         0         0
   in  85.799     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          132
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7          55
cleaning chip # 2
 Hot pixels & counts                   :               6          44
cleaning chip # 3
 
 Number of pixels rejected           :           13
 Number of (internal) image counts   :          132
 Number of image cts rejected (N, %) :           9975.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            7            6            0
 
 Image counts      :             0           77           55            0
 Image cts rejected:             0           55           44            0
 Image cts rej (%) :          0.00        71.43        80.00         0.00
 
    filtering data...
 
 Total counts      :             0           77           55            0
 Total cts rejected:             0           55           44            0
 Total cts rej (%) :          0.00        71.43        80.00         0.00
 
 Number of clean counts accepted  :           33
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           13
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad56004080s000112h.evt use_events=no
Wrote cleaned events file to ad56004080s000112h.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Skipping ad56004080s000201h.unf because of mode
-> Filtering ad56004080s000202h.unf into ad56004080s000202h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   3133.0190
 The mean of the selected column is                  20.886793
 The standard deviation of the selected column is    6.9049274
 The minimum of selected column is                   5.8214469
 The maximum of selected column is                   46.125149
 The number of points used in calculation is              150

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   3519.3713
 The mean of the selected column is                  23.462476
 The standard deviation of the selected column is    9.2303882
 The minimum of selected column is                   8.0893106
 The maximum of selected column is                   78.000252
 The number of points used in calculation is              150

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0.1 && S0_PIXL1<41.6 )&&
(S0_PIXL2>0 && S0_PIXL2<51.1 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.96E+04    11187 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           8796      4646              0      4150         0         0
 Writing events file
   4646 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8796      4646              0      4150         0         0
   in  4839.7     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4646
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8        2392
 Flickering pixels iter, pixels & cnts :   1           1           8
cleaning chip # 2
 Hot pixels & counts                   :               7        1018
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         4646
 Number of image cts rejected (N, %) :         341873.57
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0         3099         1547            0
 Image cts rejected:             0         2400         1018            0
 Image cts rej (%) :          0.00        77.44        65.80         0.00
 
    filtering data...
 
 Total counts      :             0         3099         1547            0
 Total cts rejected:             0         2400         1018            0
 Total cts rej (%) :          0.00        77.44        65.80         0.00
 
 Number of clean counts accepted  :         1228
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000202h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad56004080s000202h.evt use_events=no
Wrote cleaned events file to ad56004080s000202h.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no

-> Filtering ad56004080s000212h.unf into ad56004080s000212h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   3133.0190
 The mean of the selected column is                  20.886793
 The standard deviation of the selected column is    6.9049274
 The minimum of selected column is                   5.8214469
 The maximum of selected column is                   46.125149
 The number of points used in calculation is              150

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   3519.3713
 The mean of the selected column is                  23.462476
 The standard deviation of the selected column is    9.2303882
 The minimum of selected column is                   8.0893106
 The maximum of selected column is                   78.000252
 The number of points used in calculation is              150

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0.1 && S0_PIXL1<41.6 )&&
(S0_PIXL2>0 && S0_PIXL2<51.1 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.96E+04    11389 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000212h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           9159      4849              0      4310         0         0
 Writing events file
   4849 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9159      4849              0      4310         0         0
   in  4839.7     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4849
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8        2470
 Flickering pixels iter, pixels & cnts :   1           1           8
cleaning chip # 2
 Hot pixels & counts                   :               7        1043
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         4849
 Number of image cts rejected (N, %) :         352172.61
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0         3243         1606            0
 Image cts rejected:             0         2478         1043            0
 Image cts rej (%) :          0.00        76.41        64.94         0.00
 
    filtering data...
 
 Total counts      :             0         3243         1606            0
 Total cts rejected:             0         2478         1043            0
 Total cts rej (%) :          0.00        76.41        64.94         0.00
 
 Number of clean counts accepted  :         1328
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000212h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad56004080s000212h.evt use_events=no
Wrote cleaned events file to ad56004080s000212h.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Skipping ad56004080s000301m.unf because of mode
-> Filtering ad56004080s000302m.unf into ad56004080s000302m.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1290.6604
 The mean of the selected column is                  21.158366
 The standard deviation of the selected column is    6.2193921
 The minimum of selected column is                   8.3750267
 The maximum of selected column is                   37.875118
 The number of points used in calculation is               61

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1527.3799
 The mean of the selected column is                  23.865310
 The standard deviation of the selected column is    8.6821009
 The minimum of selected column is                   7.8437753
 The maximum of selected column is                   65.906456
 The number of points used in calculation is               64

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>2.5 && S0_PIXL1<39.8 )&&
(S0_PIXL2>0 && S0_PIXL2<49.9 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.33E+04     3794 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           2955      1701              0      1254         0         0
 Writing events file
   1701 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2955      1701              0      1254         0         0
   in  1834.2     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 File NEVENTS keyword value  :         1701
 Total counts in chip images :         1700
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8         921
cleaning chip # 2
 Hot pixels & counts                   :               6         314
 Flickering pixels iter, pixels & cnts :   1           1           6
cleaning chip # 3
 
 Number of pixels rejected           :           15
 Number of (internal) image counts   :         1700
 Number of image cts rejected (N, %) :         124173.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            7            0
 
 Image counts      :             0         1191          509            0
 Image cts rejected:             0          921          320            0
 Image cts rej (%) :          0.00        77.33        62.87         0.00
 
    filtering data...
 
 Total counts      :             0         1191          510            0
 Total cts rejected:             0          921          321            0
 Total cts rej (%) :          0.00        77.33        62.94         0.00
 
 Number of clean counts accepted  :          459
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           15
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000302m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad56004080s000302m.evt use_events=no
Wrote cleaned events file to ad56004080s000302m.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no

-> Filtering ad56004080s000312m.unf into ad56004080s000312m.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1290.6604
 The mean of the selected column is                  21.158366
 The standard deviation of the selected column is    6.2193921
 The minimum of selected column is                   8.3750267
 The maximum of selected column is                   37.875118
 The number of points used in calculation is               61

-> Calculating statistics for S0_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1527.3799
 The mean of the selected column is                  23.865310
 The standard deviation of the selected column is    8.6821009
 The minimum of selected column is                   7.8437753
 The maximum of selected column is                   65.906456
 The number of points used in calculation is               64

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>2.5 && S0_PIXL1<39.8 )&&
(S0_PIXL2>0 && S0_PIXL2<49.9 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.33E+04     3875 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000312m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           3077      1765              0      1312         0         0
 Writing events file
   1765 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3077      1765              0      1312         0         0
   in  1834.2     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1765
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8         949
cleaning chip # 2
 Hot pixels & counts                   :               6         320
 Flickering pixels iter, pixels & cnts :   1           1           6
cleaning chip # 3
 
 Number of pixels rejected           :           15
 Number of (internal) image counts   :         1765
 Number of image cts rejected (N, %) :         127572.24
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            7            0
 
 Image counts      :             0         1238          527            0
 Image cts rejected:             0          949          326            0
 Image cts rej (%) :          0.00        76.66        61.86         0.00
 
    filtering data...
 
 Total counts      :             0         1238          527            0
 Total cts rejected:             0          949          326            0
 Total cts rej (%) :          0.00        76.66        61.86         0.00
 
 Number of clean counts accepted  :          490
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           15
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000312m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad56004080s000312m.evt use_events=no
Wrote cleaned events file to ad56004080s000312m.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Skipping ad56004080s000401l.unf because of mode
-> Filtering ad56004080s000402l.unf into ad56004080s000402l.evt
-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)&&(S0_PIXL2>0)  )&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      LOW         1998-09-11  15:45:56    0.33E+04     2682 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000402l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000402l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad56004080s000402l.evt use_events=no
Wrote cleaned events file to ad56004080s000402l.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no

-> Deleting ad56004080s000402l.evt since it contains 0 events
-> Filtering ad56004080s000412l.unf into ad56004080s000412l.evt
-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)&&(S0_PIXL2>0)  )&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     LOW         1998-09-11  15:45:56    0.33E+04     2713 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000412l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s000412l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad56004080s000412l.evt use_events=no
Wrote cleaned events file to ad56004080s000412l.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Deleting ad56004080s000412l.evt since it contains 0 events
-> Skipping ad56004080s000501l.unf because of mode
-> Skipping ad56004080s000601m.unf because of mode
-> Skipping ad56004080s100101h.unf because of mode
-> Filtering ad56004080s100102h.unf into ad56004080s100102h.evt
-> Calculating statistics for S1_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   5320.8473
 The mean of the selected column is                  35.005575
 The standard deviation of the selected column is    10.871511
 The minimum of selected column is                   13.267899
 The maximum of selected column is                   96.281563
 The number of points used in calculation is              152

-> Calculating statistics for S1_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   4966.5462
 The mean of the selected column is                  32.461086
 The standard deviation of the selected column is    11.847964
 The minimum of selected column is                   9.5893154
 The maximum of selected column is                   102.06283
 The number of points used in calculation is              153

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>2.3 && S1_PIXL1<67.6 )&&
(S1_PIXL2>0 && S1_PIXL2<68 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.12E+05    31391 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          27706     12839              0     14867         0         0
 Writing events file
  12839 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         27706     12839              0     14867         0         0
   in  4843.6     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        12839
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              16        6339
 Flickering pixels iter, pixels & cnts :   1           4          60
cleaning chip # 2
 Hot pixels & counts                   :              13        5375
 Flickering pixels iter, pixels & cnts :   1           4          18
cleaning chip # 3
 
 Number of pixels rejected           :           37
 Number of (internal) image counts   :        12839
 Number of image cts rejected (N, %) :        1179291.85
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           20           17            0
 
 Image counts      :             0         6875         5964            0
 Image cts rejected:             0         6399         5393            0
 Image cts rej (%) :          0.00        93.08        90.43         0.00
 
    filtering data...
 
 Total counts      :             0         6875         5964            0
 Total cts rejected:             0         6399         5393            0
 Total cts rej (%) :          0.00        93.08        90.43         0.00
 
 Number of clean counts accepted  :         1047
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           37
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad56004080s100102h.evt use_events=no
Wrote cleaned events file to ad56004080s100102h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no

-> Filtering ad56004080s100112h.unf into ad56004080s100112h.evt
-> Calculating statistics for S1_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   5320.8473
 The mean of the selected column is                  35.005575
 The standard deviation of the selected column is    10.871511
 The minimum of selected column is                   13.267899
 The maximum of selected column is                   96.281563
 The number of points used in calculation is              152

-> Calculating statistics for S1_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   4966.5462
 The mean of the selected column is                  32.461086
 The standard deviation of the selected column is    11.847964
 The minimum of selected column is                   9.5893154
 The maximum of selected column is                   102.06283
 The number of points used in calculation is              153

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>2.3 && S1_PIXL1<67.6 )&&
(S1_PIXL2>0 && S1_PIXL2<68 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.12E+05    31727 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100112h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          28490     13128              0     15362         0         0
 Writing events file
  13128 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         28490     13128              0     15362         0         0
   in  4843.6     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        13128
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              16        6385
 Flickering pixels iter, pixels & cnts :   1           4          61
cleaning chip # 2
 Hot pixels & counts                   :              13        5563
 Flickering pixels iter, pixels & cnts :   1           4          19
cleaning chip # 3
 
 Number of pixels rejected           :           37
 Number of (internal) image counts   :        13128
 Number of image cts rejected (N, %) :        1202891.62
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           20           17            0
 
 Image counts      :             0         6934         6194            0
 Image cts rejected:             0         6446         5582            0
 Image cts rej (%) :          0.00        92.96        90.12         0.00
 
    filtering data...
 
 Total counts      :             0         6934         6194            0
 Total cts rejected:             0         6446         5582            0
 Total cts rej (%) :          0.00        92.96        90.12         0.00
 
 Number of clean counts accepted  :         1100
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           37
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad56004080s100112h.evt use_events=no
Wrote cleaned events file to ad56004080s100112h.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Skipping ad56004080s100201m.unf because of mode
-> Filtering ad56004080s100202m.unf into ad56004080s100202m.evt
-> Calculating statistics for S1_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1949.6937
 The mean of the selected column is                  33.045656
 The standard deviation of the selected column is    9.3614852
 The minimum of selected column is                   16.312551
 The maximum of selected column is                   59.781441
 The number of points used in calculation is               59

-> Calculating statistics for S1_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   2030.6940
 The mean of the selected column is                  34.418542
 The standard deviation of the selected column is    8.4532485
 The minimum of selected column is                   15.281299
 The maximum of selected column is                   54.687672
 The number of points used in calculation is               59

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>4.9 && S1_PIXL1<61.1 )&&
(S1_PIXL2>9 && S1_PIXL2<59.7 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.35E+04     9561 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           8587      4529              0      4058         0         0
 Writing events file
   4529 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8587      4529              0      4058         0         0
   in  1706.2     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4529
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              14        2230
 Flickering pixels iter, pixels & cnts :   1           5          45
cleaning chip # 2
 Hot pixels & counts                   :              12        1868
 Flickering pixels iter, pixels & cnts :   1           2          11
cleaning chip # 3
 
 Number of pixels rejected           :           33
 Number of (internal) image counts   :         4529
 Number of image cts rejected (N, %) :         415491.72
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           19           14            0
 
 Image counts      :             0         2448         2081            0
 Image cts rejected:             0         2275         1879            0
 Image cts rej (%) :          0.00        92.93        90.29         0.00
 
    filtering data...
 
 Total counts      :             0         2448         2081            0
 Total cts rejected:             0         2275         1879            0
 Total cts rej (%) :          0.00        92.93        90.29         0.00
 
 Number of clean counts accepted  :          375
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           33
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad56004080s100202m.evt use_events=no
Wrote cleaned events file to ad56004080s100202m.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no

-> Filtering ad56004080s100212m.unf into ad56004080s100212m.evt
-> Calculating statistics for S1_PIXL1
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   1949.6937
 The mean of the selected column is                  33.045656
 The standard deviation of the selected column is    9.3614852
 The minimum of selected column is                   16.312551
 The maximum of selected column is                   59.781441
 The number of points used in calculation is               59

-> Calculating statistics for S1_PIXL2
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   2030.6940
 The mean of the selected column is                  34.418542
 The standard deviation of the selected column is    8.4532485
 The minimum of selected column is                   15.281299
 The maximum of selected column is                   54.687672
 The number of points used in calculation is               59

-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>4.9 && S1_PIXL1<61.1 )&&
(S1_PIXL2>9 && S1_PIXL2<59.7 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.35E+04     9614 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100212m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           8777      4627              0      4150         0         0
 Writing events file
   4627 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8777      4627              0      4150         0         0
   in  1706.2     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4627
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              14        2247
 Flickering pixels iter, pixels & cnts :   1           5          45
cleaning chip # 2
 Hot pixels & counts                   :              12        1934
 Flickering pixels iter, pixels & cnts :   1           2          11
cleaning chip # 3
 
 Number of pixels rejected           :           33
 Number of (internal) image counts   :         4627
 Number of image cts rejected (N, %) :         423791.57
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           19           14            0
 
 Image counts      :             0         2469         2158            0
 Image cts rejected:             0         2292         1945            0
 Image cts rej (%) :          0.00        92.83        90.13         0.00
 
    filtering data...
 
 Total counts      :             0         2469         2158            0
 Total cts rejected:             0         2292         1945            0
 Total cts rej (%) :          0.00        92.83        90.13         0.00
 
 Number of clean counts accepted  :          390
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           33
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad56004080s100212m.evt use_events=no
Wrote cleaned events file to ad56004080s100212m.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Skipping ad56004080s100301l.unf because of mode
-> Filtering ad56004080s100302l.unf into ad56004080s100302l.evt
-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>0)&&(S1_PIXL2>0)  )&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      LOW         1998-09-11  15:45:56    0.56E+04     6355 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100302l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad56004080s100302l.evt use_events=no
Wrote cleaned events file to ad56004080s100302l.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no

-> Deleting ad56004080s100302l.evt since it contains 0 events
-> Filtering ad56004080s100312l.unf into ad56004080s100312l.evt
-> Using the following selection criteria:

(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>0)&&(S1_PIXL2>0)  )&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     LOW         1998-09-11  15:45:56    0.56E+04     6423 0110
Processing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100312l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data23/seq_proc/ad0_56004080.003/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data23/seq_proc/ad0_56004080.003/screen_in_event.xs
    reading data file: /data/data23/seq_proc/ad0_56004080.003/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080s100312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad56004080s100312l.evt use_events=no
Wrote cleaned events file to ad56004080s100312l.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Deleting ad56004080s100312l.evt since it contains 0 events
-> Filtering ad56004080g200170h.unf into ad56004080g200170h.evt
-> Fetching GIS2_REGION256.4
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15805      5473           6094      4238         0         0
 Writing events file
   5473 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15805      5473           6094      4238         0         0
   in  4824.0     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        5473                5199               274
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad56004080g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no

-> Filtering ad56004080g200270l.unf into ad56004080g200270l.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7859        94           2844      4921         0         0
 Writing events file
     94 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7859        94           2844      4921         0         0
   in  96.000     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
          94                  91                 3
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g200270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad56004080g200270l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no

-> Filtering ad56004080g200370m.unf into ad56004080g200370m.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4819     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4819      2645           1796       378         0         0
 Writing events file
   2645 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4819      2645           1796       378         0         0
   in  2400.1     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        2645                2506               139
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g200370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad56004080g200370m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no

-> Filtering ad56004080g300170h.unf into ad56004080g300170h.evt
-> Fetching GIS3_REGION256.4
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15310      5808           5053      4449         0         0
 Writing events file
   5808 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15310      5808           5053      4449         0         0
   in  4822.0     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        5808                5515               293
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad56004080g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no

-> Filtering ad56004080g300270l.unf into ad56004080g300270l.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7784     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7784       112           2360      5312         0         0
 Writing events file
    112 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7784       112           2360      5312         0         0
   in  96.000     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
         112                 111                 1
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g300270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad56004080g300270l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no

-> Filtering ad56004080g300370m.unf into ad56004080g300370m.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:

(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4854     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4854      2942           1450       462         0         0
 Writing events file
   2942 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4854      2942           1450       462         0         0
   in  2400.1     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        2942                2808               134
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA > read events ad56004080g300370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad56004080g300370m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no

Generating images and exposure maps (8:14:21)

-> Generating exposure map ad56004080g200170.expo
-> GIS2_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:

-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(167.5,220,24.66,28.95,245.298)

-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g200170h.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g200170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1149
 Mean   RA/DEC/ROLL :      265.5711     -30.1055      83.1149
 Pnt    RA/DEC/ROLL :      265.5709     -30.1676      83.1149
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :            13
 Total GTI (secs)   :      4824.035
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        896.50       896.50
  20 Percent Complete: Total/live time:       1024.50      1024.50
  30 Percent Complete: Total/live time:       1508.00      1508.00
  40 Percent Complete: Total/live time:       2529.99      2529.99
  50 Percent Complete: Total/live time:       2529.99      2529.99
  60 Percent Complete: Total/live time:       3449.99      3449.99
  70 Percent Complete: Total/live time:       3449.99      3449.99
  80 Percent Complete: Total/live time:       3917.54      3917.54
  90 Percent Complete: Total/live time:       4824.04      4824.04
 100 Percent Complete: Total/live time:       4824.04      4824.04
 
 Number of attitude steps  used:           70
 Number of attitude steps avail:        11895
 Mean RA/DEC pixel offset:       -9.9964      -4.4975
 
    writing expo file: ad56004080g200170.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g200170h.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g200170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199      5143             56         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5199      5143             56         0         0         0
   in  4824.0     seconds
 Image            has     5143 counts for  1.066     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199      1178             56         0         0      3965
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5199      1178             56         0         0      3965
   in  4824.0     seconds
 Image            has     1178 counts for 0.2442     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199      3989             56         0         0      1154
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5199      3989             56         0         0      1154
   in  4824.0     seconds
 Image            has     3989 counts for 0.8269     counts/sec
 Command not found; type ? for a command listing
!ad56004080g200170h:ASCA >
!ad56004080g200170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g200170h:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200170h:ASCA > read events ad56004080g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200170h:ASCA-GIS2-PH > set image sky
!ad56004080g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad56004080g200170h:ASCA-GIS2-PH > extract image
!ad56004080g200170h:ASCA-GIS2-PH > save image outfile=ad56004080g200170_all.img
Wrote image to file ad56004080g200170_all.img
!ad56004080g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad56004080g200170h:ASCA-GIS2-PH > extract image
!ad56004080g200170h:ASCA-GIS2-PH > save image outfile=ad56004080g200170_lo.img
Wrote image to file ad56004080g200170_lo.img
!ad56004080g200170h:ASCA-GIS2-PH > clear pha_cut
!ad56004080g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g200170h:ASCA-GIS2-PH > extract image
!ad56004080g200170h:ASCA-GIS2-PH > save image outfile=ad56004080g200170_hi.img
Wrote image to file ad56004080g200170_hi.img
!ad56004080g200170h:ASCA-GIS2-PH > exit save_session=no

-> Generating exposure map ad56004080g200270.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g200270l.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g200270l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1140
 Mean   RA/DEC/ROLL :      265.5747     -30.1089      83.1140
 Pnt    RA/DEC/ROLL :      265.5527     -30.1501      83.1140
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :             1
 Total GTI (secs)   :        96.000
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:         11.94        11.94
  20 Percent Complete: Total/live time:         96.00        96.00
 100 Percent Complete: Total/live time:         96.00        96.00
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:           12
 Mean RA/DEC pixel offset:       -5.1915      -2.0854
 
    writing expo file: ad56004080g200270.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g200270l.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g200270l
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        90              1         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            91        90              1         0         0         0
   in  96.000     seconds
 Image            has       90 counts for 0.9375     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        27              1         0         0        63
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            91        27              1         0         0        63
   in  96.000     seconds
 Image            has       27 counts for 0.2812     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        63              1         0         0        27
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            91        63              1         0         0        27
   in  96.000     seconds
 Image            has       63 counts for 0.6562     counts/sec
 Command not found; type ? for a command listing
!ad56004080g200270l:ASCA >
!ad56004080g200270l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g200270l:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200270l:ASCA > read events ad56004080g200270l.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200270l:ASCA-GIS2-PH > set image sky
!ad56004080g200270l:ASCA-GIS2-PH > filter region corner_point.reg
!ad56004080g200270l:ASCA-GIS2-PH > extract image
!ad56004080g200270l:ASCA-GIS2-PH > save image outfile=ad56004080g200270_all.img
Wrote image to file ad56004080g200270_all.img
!ad56004080g200270l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad56004080g200270l:ASCA-GIS2-PH > extract image
!ad56004080g200270l:ASCA-GIS2-PH > save image outfile=ad56004080g200270_lo.img
Wrote image to file ad56004080g200270_lo.img
!ad56004080g200270l:ASCA-GIS2-PH > clear pha_cut
!ad56004080g200270l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g200270l:ASCA-GIS2-PH > extract image
!ad56004080g200270l:ASCA-GIS2-PH > save image outfile=ad56004080g200270_hi.img
Wrote image to file ad56004080g200270_hi.img
!ad56004080g200270l:ASCA-GIS2-PH > exit save_session=no

-> Generating exposure map ad56004080g200370.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g200370m.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g200370m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1140
 Mean   RA/DEC/ROLL :      265.5729     -30.1120      83.1140
 Pnt    RA/DEC/ROLL :      265.5507     -30.1493      83.1140
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :             4
 Total GTI (secs)   :      2400.065
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        396.00       396.00
  20 Percent Complete: Total/live time:        888.00       888.00
  30 Percent Complete: Total/live time:        888.00       888.00
  40 Percent Complete: Total/live time:       1152.06      1152.06
  50 Percent Complete: Total/live time:       1279.98      1279.98
  60 Percent Complete: Total/live time:       1471.98      1471.98
  70 Percent Complete: Total/live time:       2251.98      2251.98
  80 Percent Complete: Total/live time:       2251.98      2251.98
  90 Percent Complete: Total/live time:       2400.06      2400.06
 100 Percent Complete: Total/live time:       2400.06      2400.06
 
 Number of attitude steps  used:           21
 Number of attitude steps avail:          860
 Mean RA/DEC pixel offset:       -9.8074      -3.6812
 
    writing expo file: ad56004080g200370.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g200370m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g200370m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2506     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506      2466             40         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2506      2466             40         0         0         0
   in  2400.1     seconds
 Image            has     2466 counts for  1.027     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506       579             40         0         0      1887
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2506       579             40         0         0      1887
   in  2400.1     seconds
 Image            has      579 counts for 0.2412     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506      1892             40         0         0       574
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2506      1892             40         0         0       574
   in  2400.1     seconds
 Image            has     1892 counts for 0.7883     counts/sec
 Command not found; type ? for a command listing
!ad56004080g200370m:ASCA >
!ad56004080g200370m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g200370m:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200370m:ASCA > read events ad56004080g200370m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g200370m:ASCA-GIS2-PH > set image sky
!ad56004080g200370m:ASCA-GIS2-PH > filter region corner_point.reg
!ad56004080g200370m:ASCA-GIS2-PH > extract image
!ad56004080g200370m:ASCA-GIS2-PH > save image outfile=ad56004080g200370_all.img
Wrote image to file ad56004080g200370_all.img
!ad56004080g200370m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad56004080g200370m:ASCA-GIS2-PH > extract image
!ad56004080g200370m:ASCA-GIS2-PH > save image outfile=ad56004080g200370_lo.img
Wrote image to file ad56004080g200370_lo.img
!ad56004080g200370m:ASCA-GIS2-PH > clear pha_cut
!ad56004080g200370m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g200370m:ASCA-GIS2-PH > extract image
!ad56004080g200370m:ASCA-GIS2-PH > save image outfile=ad56004080g200370_hi.img
Wrote image to file ad56004080g200370_hi.img
!ad56004080g200370m:ASCA-GIS2-PH > exit save_session=no

-> Generating exposure map ad56004080g300170.expo
-> GIS3_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:

-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(217,95,21.56,25.92,169.216)

-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g300170h.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g300170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1181
 Mean   RA/DEC/ROLL :      265.5648     -30.1297      83.1181
 Pnt    RA/DEC/ROLL :      265.5771     -30.1434      83.1181
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :            13
 Total GTI (secs)   :      4822.035
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        896.50       896.50
  20 Percent Complete: Total/live time:       1024.50      1024.50
  30 Percent Complete: Total/live time:       1508.00      1508.00
  40 Percent Complete: Total/live time:       2529.99      2529.99
  50 Percent Complete: Total/live time:       2529.99      2529.99
  60 Percent Complete: Total/live time:       3449.99      3449.99
  70 Percent Complete: Total/live time:       3449.99      3449.99
  80 Percent Complete: Total/live time:       3915.54      3915.54
  90 Percent Complete: Total/live time:       4822.04      4822.04
 100 Percent Complete: Total/live time:       4822.04      4822.04
 
 Number of attitude steps  used:           70
 Number of attitude steps avail:        11895
 Mean RA/DEC pixel offset:        1.9097      -3.3147
 
    writing expo file: ad56004080g300170.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g300170h.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g300170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515      5441             74         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5515      5441             74         0         0         0
   in  4822.0     seconds
 Image            has     5441 counts for  1.128     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515      1185             74         0         0      4256
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5515      1185             74         0         0      4256
   in  4822.0     seconds
 Image            has     1185 counts for 0.2457     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515      4278             74         0         0      1163
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5515      4278             74         0         0      1163
   in  4822.0     seconds
 Image            has     4278 counts for 0.8872     counts/sec
 Command not found; type ? for a command listing
!ad56004080g300170h:ASCA >
!ad56004080g300170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g300170h:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300170h:ASCA > read events ad56004080g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300170h:ASCA-GIS3-PH > set image sky
!ad56004080g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad56004080g300170h:ASCA-GIS3-PH > extract image
!ad56004080g300170h:ASCA-GIS3-PH > save image outfile=ad56004080g300170_all.img
Wrote image to file ad56004080g300170_all.img
!ad56004080g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad56004080g300170h:ASCA-GIS3-PH > extract image
!ad56004080g300170h:ASCA-GIS3-PH > save image outfile=ad56004080g300170_lo.img
Wrote image to file ad56004080g300170_lo.img
!ad56004080g300170h:ASCA-GIS3-PH > clear pha_cut
!ad56004080g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g300170h:ASCA-GIS3-PH > extract image
!ad56004080g300170h:ASCA-GIS3-PH > save image outfile=ad56004080g300170_hi.img
Wrote image to file ad56004080g300170_hi.img
!ad56004080g300170h:ASCA-GIS3-PH > exit save_session=no

-> Generating exposure map ad56004080g300270.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g300270l.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g300270l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1172
 Mean   RA/DEC/ROLL :      265.5684     -30.1331      83.1172
 Pnt    RA/DEC/ROLL :      265.5590     -30.1259      83.1172
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :             1
 Total GTI (secs)   :        96.000
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:         11.94        11.94
  20 Percent Complete: Total/live time:         96.00        96.00
 100 Percent Complete: Total/live time:         96.00        96.00
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:           12
 Mean RA/DEC pixel offset:        0.8478      -1.4854
 
    writing expo file: ad56004080g300270.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g300270l.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g300270l
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111       110              1         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           111       110              1         0         0         0
   in  96.000     seconds
 Image            has      110 counts for  1.146     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111        24              1         0         0        86
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           111        24              1         0         0        86
   in  96.000     seconds
 Image            has       24 counts for 0.2500     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111        86              1         0         0        24
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           111        86              1         0         0        24
   in  96.000     seconds
 Image            has       86 counts for 0.8958     counts/sec
 Command not found; type ? for a command listing
!ad56004080g300270l:ASCA >
!ad56004080g300270l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g300270l:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300270l:ASCA > read events ad56004080g300270l.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300270l:ASCA-GIS3-PH > set image sky
!ad56004080g300270l:ASCA-GIS3-PH > filter region corner_point.reg
!ad56004080g300270l:ASCA-GIS3-PH > extract image
!ad56004080g300270l:ASCA-GIS3-PH > save image outfile=ad56004080g300270_all.img
Wrote image to file ad56004080g300270_all.img
!ad56004080g300270l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad56004080g300270l:ASCA-GIS3-PH > extract image
!ad56004080g300270l:ASCA-GIS3-PH > save image outfile=ad56004080g300270_lo.img
Wrote image to file ad56004080g300270_lo.img
!ad56004080g300270l:ASCA-GIS3-PH > clear pha_cut
!ad56004080g300270l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g300270l:ASCA-GIS3-PH > extract image
!ad56004080g300270l:ASCA-GIS3-PH > save image outfile=ad56004080g300270_hi.img
Wrote image to file ad56004080g300270_hi.img
!ad56004080g300270l:ASCA-GIS3-PH > exit save_session=no

-> Generating exposure map ad56004080g300370.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad56004080g300370m.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080g300370m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1171
 Mean   RA/DEC/ROLL :      265.5665     -30.1366      83.1171
 Pnt    RA/DEC/ROLL :      265.5570     -30.1251      83.1171
 
 Image rebin factor :             1
 Attitude Records   :         28248
 GTI intervals      :             4
 Total GTI (secs)   :      2400.065
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        396.00       396.00
  20 Percent Complete: Total/live time:        888.00       888.00
  30 Percent Complete: Total/live time:        888.00       888.00
  40 Percent Complete: Total/live time:       1152.06      1152.06
  50 Percent Complete: Total/live time:       1279.98      1279.98
  60 Percent Complete: Total/live time:       1471.98      1471.98
  70 Percent Complete: Total/live time:       2251.98      2251.98
  80 Percent Complete: Total/live time:       2251.98      2251.98
  90 Percent Complete: Total/live time:       2400.06      2400.06
 100 Percent Complete: Total/live time:       2400.06      2400.06
 
 Number of attitude steps  used:           21
 Number of attitude steps avail:          860
 Mean RA/DEC pixel offset:        1.6960      -2.5385
 
    writing expo file: ad56004080g300370.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080g300370m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080g300370m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2808     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808      2764             44         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2808      2764             44         0         0         0
   in  2400.1     seconds
 Image            has     2764 counts for  1.152     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808       632             44         0         0      2132
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2808       632             44         0         0      2132
   in  2400.1     seconds
 Image            has      632 counts for 0.2633     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808      2141             44         0         0       623
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2808      2141             44         0         0       623
   in  2400.1     seconds
 Image            has     2141 counts for 0.8921     counts/sec
 Command not found; type ? for a command listing
!ad56004080g300370m:ASCA >
!ad56004080g300370m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080g300370m:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300370m:ASCA > read events ad56004080g300370m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080g300370m:ASCA-GIS3-PH > set image sky
!ad56004080g300370m:ASCA-GIS3-PH > filter region corner_point.reg
!ad56004080g300370m:ASCA-GIS3-PH > extract image
!ad56004080g300370m:ASCA-GIS3-PH > save image outfile=ad56004080g300370_all.img
Wrote image to file ad56004080g300370_all.img
!ad56004080g300370m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad56004080g300370m:ASCA-GIS3-PH > extract image
!ad56004080g300370m:ASCA-GIS3-PH > save image outfile=ad56004080g300370_lo.img
Wrote image to file ad56004080g300370_lo.img
!ad56004080g300370m:ASCA-GIS3-PH > clear pha_cut
!ad56004080g300370m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad56004080g300370m:ASCA-GIS3-PH > extract image
!ad56004080g300370m:ASCA-GIS3-PH > save image outfile=ad56004080g300370_hi.img
Wrote image to file ad56004080g300370_hi.img
!ad56004080g300370m:ASCA-GIS3-PH > exit save_session=no

-> Generating exposure map ad56004080s000102.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad56004080s000102h.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080s000102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL          ON
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1067
 Mean   RA/DEC/ROLL :      265.5896     -30.1225      83.1067
 Pnt    RA/DEC/ROLL :      265.5357     -30.1366      83.1067
 
 Image rebin factor :             4
 Attitude Records   :         28248
 Hot Pixels         :            12
 GTI intervals      :             1
 Total GTI (secs)   :        85.799
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:         85.80        85.80
 100 Percent Complete: Total/live time:         85.80        85.80
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:          323
 Mean RA/DEC pixel offset:      -20.9963     -51.3750
 
    writing expo file: ad56004080s000102.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080s000102h.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080s000102h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.86E+02       31 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             31        31              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            31        31              0         0         0         0
   in  85.799     seconds
 Image            has       31 counts for 0.3613     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             31         8              0         0         0        23
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            31         8              0         0         0        23
   in  85.799     seconds
 Image            has        8 counts for 9.3241E-02 counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             31        23              0         0         0         8
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            31        23              0         0         0         8
   in  85.799     seconds
 Image            has       23 counts for 0.2681     counts/sec
 Command not found; type ? for a command listing
!ad56004080s000102h:ASCA >
!ad56004080s000102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080s000102h:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000102h:ASCA > read events ad56004080s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad56004080s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad56004080s000102h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000102_all.img
Wrote image to file ad56004080s000102_all.img
!ad56004080s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad56004080s000102h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000102_lo.img
Wrote image to file ad56004080s000102_lo.img
!ad56004080s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad56004080s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad56004080s000102h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000102_hi.img
Wrote image to file ad56004080s000102_hi.img
!ad56004080s000102h:ASCA-SIS0-BRIGHT > exit save_session=no

-> Generating exposure map ad56004080s000202.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad56004080s000202h.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080s000202h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1079
 Mean   RA/DEC/ROLL :      265.5848     -30.1189      83.1079
 Pnt    RA/DEC/ROLL :      265.5562     -30.1534      83.1079
 
 Image rebin factor :             4
 Attitude Records   :         28248
 Hot Pixels         :            16
 GTI intervals      :            16
 Total GTI (secs)   :      4839.657
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        896.00       896.00
  20 Percent Complete: Total/live time:       1032.97      1032.97
  30 Percent Complete: Total/live time:       1527.32      1527.32
  40 Percent Complete: Total/live time:       2582.80      2582.80
  50 Percent Complete: Total/live time:       2582.80      2582.80
  60 Percent Complete: Total/live time:       3165.80      3165.80
  70 Percent Complete: Total/live time:       3557.30      3557.30
  80 Percent Complete: Total/live time:       4303.28      4303.28
  90 Percent Complete: Total/live time:       4634.78      4634.78
 100 Percent Complete: Total/live time:       4839.66      4839.66
 
 Number of attitude steps  used:           66
 Number of attitude steps avail:        11540
 Mean RA/DEC pixel offset:      -36.8032    -104.0345
 
    writing expo file: ad56004080s000202.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080s000202h.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080s000202h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228      1228              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1228      1228              0         0         0         0
   in  4839.7     seconds
 Image            has     1228 counts for 0.2537     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228       242              0         0         0       986
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1228       242              0         0         0       986
   in  4839.7     seconds
 Image            has      242 counts for 5.0004E-02 counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228       987              0         0         0       241
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1228       987              0         0         0       241
   in  4839.7     seconds
 Image            has      987 counts for 0.2039     counts/sec
 Command not found; type ? for a command listing
!ad56004080s000202h:ASCA >
!ad56004080s000202h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080s000202h:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000202h:ASCA > read events ad56004080s000202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad56004080s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad56004080s000202h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000202_all.img
Wrote image to file ad56004080s000202_all.img
!ad56004080s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad56004080s000202h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000202_lo.img
Wrote image to file ad56004080s000202_lo.img
!ad56004080s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad56004080s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad56004080s000202h:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000202_hi.img
Wrote image to file ad56004080s000202_hi.img
!ad56004080s000202h:ASCA-SIS0-BRIGHT > exit save_session=no

-> Generating exposure map ad56004080s000302.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad56004080s000302m.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080s000302m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1079
 Mean   RA/DEC/ROLL :      265.5887     -30.1228      83.1079
 Pnt    RA/DEC/ROLL :      265.5560     -30.1537      83.1079
 
 Image rebin factor :             4
 Attitude Records   :         28248
 Hot Pixels         :            15
 GTI intervals      :            17
 Total GTI (secs)   :      1834.190
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        310.12       310.12
  20 Percent Complete: Total/live time:        706.12       706.12
  30 Percent Complete: Total/live time:        706.12       706.12
  40 Percent Complete: Total/live time:        842.19       842.19
  50 Percent Complete: Total/live time:       1055.98      1055.98
  60 Percent Complete: Total/live time:       1162.19      1162.19
  70 Percent Complete: Total/live time:       1330.11      1330.11
  80 Percent Complete: Total/live time:       1578.19      1578.19
  90 Percent Complete: Total/live time:       1834.19      1834.19
 100 Percent Complete: Total/live time:       1834.19      1834.19
 
 Number of attitude steps  used:           23
 Number of attitude steps avail:          865
 Mean RA/DEC pixel offset:      -37.1103     -94.8832
 
    writing expo file: ad56004080s000302.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080s000302m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080s000302m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.18E+04      459 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       459              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           459       459              0         0         0         0
   in  1834.2     seconds
 Image            has      459 counts for 0.2502     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459        94              0         0         0       365
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           459        94              0         0         0       365
   in  1834.2     seconds
 Image            has       94 counts for 5.1249E-02 counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       366              0         0         0        93
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           459       366              0         0         0        93
   in  1834.2     seconds
 Image            has      366 counts for 0.1995     counts/sec
 Command not found; type ? for a command listing
!ad56004080s000302m:ASCA >
!ad56004080s000302m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080s000302m:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000302m:ASCA > read events ad56004080s000302m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad56004080s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad56004080s000302m:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000302_all.img
Wrote image to file ad56004080s000302_all.img
!ad56004080s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad56004080s000302m:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000302_lo.img
Wrote image to file ad56004080s000302_lo.img
!ad56004080s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad56004080s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad56004080s000302m:ASCA-SIS0-BRIGHT > extract image
!ad56004080s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad56004080s000302_hi.img
Wrote image to file ad56004080s000302_hi.img
!ad56004080s000302m:ASCA-SIS0-BRIGHT > exit save_session=no

-> Generating exposure map ad56004080s100102.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad56004080s100102h.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080s100102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1169
 Mean   RA/DEC/ROLL :      265.5672     -30.1165      83.1169
 Pnt    RA/DEC/ROLL :      265.5742     -30.1563      83.1169
 
 Image rebin factor :             4
 Attitude Records   :         28248
 Hot Pixels         :            37
 GTI intervals      :            17
 Total GTI (secs)   :      4843.610
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        904.47       904.47
  20 Percent Complete: Total/live time:       1032.47      1032.47
  30 Percent Complete: Total/live time:       1517.47      1517.47
  40 Percent Complete: Total/live time:       2536.96      2536.96
  50 Percent Complete: Total/live time:       2536.96      2536.96
  60 Percent Complete: Total/live time:       3119.95      3119.95
  70 Percent Complete: Total/live time:       3507.45      3507.45
  80 Percent Complete: Total/live time:       4253.44      4253.44
  90 Percent Complete: Total/live time:       4638.74      4638.74
 100 Percent Complete: Total/live time:       4843.61      4843.61
 
 Number of attitude steps  used:           68
 Number of attitude steps avail:        11641
 Mean RA/DEC pixel offset:      -41.8130     -33.9662
 
    writing expo file: ad56004080s100102.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080s100102h.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080s100102h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047      1047              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1047      1047              0         0         0         0
   in  4843.6     seconds
 Image            has     1047 counts for 0.2162     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047       249              0         0         0       798
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1047       249              0         0         0       798
   in  4843.6     seconds
 Image            has      249 counts for 5.1408E-02 counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047       799              0         0         0       248
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1047       799              0         0         0       248
   in  4843.6     seconds
 Image            has      799 counts for 0.1650     counts/sec
 Command not found; type ? for a command listing
!ad56004080s100102h:ASCA >
!ad56004080s100102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080s100102h:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s100102h:ASCA > read events ad56004080s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad56004080s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad56004080s100102h:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100102_all.img
Wrote image to file ad56004080s100102_all.img
!ad56004080s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad56004080s100102h:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100102_lo.img
Wrote image to file ad56004080s100102_lo.img
!ad56004080s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad56004080s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad56004080s100102h:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100102_hi.img
Wrote image to file ad56004080s100102_hi.img
!ad56004080s100102h:ASCA-SIS1-BRIGHT > exit save_session=no

-> Generating exposure map ad56004080s100202.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad56004080s100202m.evt
-> Standard Output From FTOOL ascaexpo:

ASCAEXPO_V0.9b
 
    reading data file: ad56004080s100202m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa980911_1122.1920
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      265.5623     -30.1290      83.1169
 Mean   RA/DEC/ROLL :      265.5706     -30.1199      83.1169
 Pnt    RA/DEC/ROLL :      265.5742     -30.1565      83.1169
 
 Image rebin factor :             4
 Attitude Records   :         28248
 Hot Pixels         :            33
 GTI intervals      :            14
 Total GTI (secs)   :      1706.190
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        342.12       342.12
  20 Percent Complete: Total/live time:        362.19       362.19
  30 Percent Complete: Total/live time:        682.12       682.12
  40 Percent Complete: Total/live time:        778.19       778.19
  50 Percent Complete: Total/live time:        895.98       895.98
  60 Percent Complete: Total/live time:       1046.11      1046.11
  70 Percent Complete: Total/live time:       1686.10      1686.10
  80 Percent Complete: Total/live time:       1686.10      1686.10
  90 Percent Complete: Total/live time:       1706.19      1706.19
 100 Percent Complete: Total/live time:       1706.19      1706.19
 
 Number of attitude steps  used:           20
 Number of attitude steps avail:          857
 Mean RA/DEC pixel offset:      -41.1303     -26.2350
 
    writing expo file: ad56004080s100202.expo
    closing attitude file...
    closing data file...

-> Generating low and high energy images for ad56004080s100202m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad56004080s100202m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.17E+04      375 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       375              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           375       375              0         0         0         0
   in  1706.2     seconds
 Image            has      375 counts for 0.2198     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       100              0         0         0       275
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           375       100              0         0         0       275
   in  1706.2     seconds
 Image            has      100 counts for 5.8610E-02 counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       275              0         0         0       100
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           375       275              0         0         0       100
   in  1706.2     seconds
 Image            has      275 counts for 0.1612     counts/sec
 Command not found; type ? for a command listing
!ad56004080s100202m:ASCA >
!ad56004080s100202m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad56004080s100202m:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s100202m:ASCA > read events ad56004080s100202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!ad56004080s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad56004080s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad56004080s100202m:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100202_all.img
Wrote image to file ad56004080s100202_all.img
!ad56004080s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad56004080s100202m:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100202_lo.img
Wrote image to file ad56004080s100202_lo.img
!ad56004080s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad56004080s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad56004080s100202m:ASCA-SIS1-BRIGHT > extract image
!ad56004080s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad56004080s100202_hi.img
Wrote image to file ad56004080s100202_hi.img
!ad56004080s100202m:ASCA-SIS1-BRIGHT > exit save_session=no

-> Summing sis images
-> Exposure for ad56004080s000102.expo is 85.799332 seconds
-> Exposure for ad56004080s000202.expo is 4839.657227 seconds
-> Exposure for ad56004080s000302.expo is 1834.189941 seconds
-> Exposure for ad56004080s100102.expo is 4843.610352 seconds
-> Exposure for ad56004080s100202.expo is 1706.189941 seconds
-> Summing the following images to produce ad56004080sis32002.totexpo

ad56004080s000102.expo
ad56004080s000202.expo
ad56004080s000302.expo
ad56004080s100102.expo
ad56004080s100202.expo

-> Setting EXPOSURE=13309.446793 in ad56004080sis32002.totexpo
-> Exposure for ad56004080s000102_all.img is 8.579933035373688E+01 seconds
-> ad56004080s000102_all.img has 31 counts
-> Exposure for ad56004080s000202_all.img is 4.839656724005938E+03 seconds
-> ad56004080s000202_all.img has 1228 counts
-> Exposure for ad56004080s000302_all.img is 1.834189909130335E+03 seconds
-> ad56004080s000302_all.img has 459 counts
-> Exposure for ad56004080s100102_all.img is 4.843610019862652E+03 seconds
-> ad56004080s100102_all.img has 1047 counts
-> Exposure for ad56004080s100202_all.img is 1.706189909130335E+03 seconds
-> ad56004080s100202_all.img has 375 counts
-> Summing the following images to produce ad56004080sis32002_all.totsky

ad56004080s000102_all.img
ad56004080s000202_all.img
ad56004080s000302_all.img
ad56004080s100102_all.img
ad56004080s100202_all.img

-> Setting EXPOSURE=13309.445892483 in ad56004080sis32002_all.totsky
-> Setting TOTCTS=3140 in ad56004080sis32002_all.totsky
-> Exposure for ad56004080s000102_lo.img is 8.579933035373688E+01 seconds
-> ad56004080s000102_lo.img has 8 counts
-> Exposure for ad56004080s000202_lo.img is 4.839656724005938E+03 seconds
-> ad56004080s000202_lo.img has 242 counts
-> Exposure for ad56004080s000302_lo.img is 1.834189909130335E+03 seconds
-> ad56004080s000302_lo.img has 94 counts
-> Exposure for ad56004080s100102_lo.img is 4.843610019862652E+03 seconds
-> ad56004080s100102_lo.img has 249 counts
-> Exposure for ad56004080s100202_lo.img is 1.706189909130335E+03 seconds
-> ad56004080s100202_lo.img has 100 counts
-> Summing the following images to produce ad56004080sis32002_lo.totsky

ad56004080s000102_lo.img
ad56004080s000202_lo.img
ad56004080s000302_lo.img
ad56004080s100102_lo.img
ad56004080s100202_lo.img

-> Setting EXPOSURE=13309.445892483 in ad56004080sis32002_lo.totsky
-> Setting TOTCTS=693 in ad56004080sis32002_lo.totsky
-> Exposure for ad56004080s000102_hi.img is 8.579933035373688E+01 seconds
-> ad56004080s000102_hi.img has 23 counts
-> Exposure for ad56004080s000202_hi.img is 4.839656724005938E+03 seconds
-> ad56004080s000202_hi.img has 987 counts
-> Exposure for ad56004080s000302_hi.img is 1.834189909130335E+03 seconds
-> ad56004080s000302_hi.img has 366 counts
-> Exposure for ad56004080s100102_hi.img is 4.843610019862652E+03 seconds
-> ad56004080s100102_hi.img has 799 counts
-> Exposure for ad56004080s100202_hi.img is 1.706189909130335E+03 seconds
-> ad56004080s100202_hi.img has 275 counts
-> Summing the following images to produce ad56004080sis32002_hi.totsky

ad56004080s000102_hi.img
ad56004080s000202_hi.img
ad56004080s000302_hi.img
ad56004080s100102_hi.img
ad56004080s100202_hi.img

-> Setting EXPOSURE=13309.445892483 in ad56004080sis32002_hi.totsky
-> Setting TOTCTS=2450 in ad56004080sis32002_hi.totsky
-> Running XIMAGE to create ad56004080sis32002.gif
-> Standard Output From STOOL ximage:

 No of detectors read in:   21
![1]XIMAGE> read/fits ad56004080sis32002_all.totsky
 Telescope ASCA SIS0,SIS1
 Image size = 320 x 320 pixels
 Image rebin = 4
 Image center = 640.5, 640.5
 Reading an image
  Image level, min = 0.0000000 max = 4.0000000
 Saving current map
![2]XIMAGE> read/expo ad56004080sis32002.totexpo
 Telescope ASCA SIS0,SIS1
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 209.80849
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.15912
  Scaling factor :     12.5000
  Min and max :   0  5
 Max-preserving scaling factor :    10.0000000
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     4436.51
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit

-> Summing gis images
-> Exposure for ad56004080g200170.expo is 4824.035156 seconds
-> Exposure for ad56004080g200270.expo is 96.000000 seconds
-> Exposure for ad56004080g200370.expo is 2400.064941 seconds
-> Exposure for ad56004080g300170.expo is 4822.035156 seconds
-> Exposure for ad56004080g300270.expo is 96.000000 seconds
-> Exposure for ad56004080g300370.expo is 2400.064941 seconds
-> Summing the following images to produce ad56004080gis25670.totexpo

ad56004080g200170.expo
ad56004080g200270.expo
ad56004080g200370.expo
ad56004080g300170.expo
ad56004080g300270.expo
ad56004080g300370.expo

-> Setting EXPOSURE=14638.200194 in ad56004080gis25670.totexpo
-> Exposure for ad56004080g200170_all.img is 4.824034888565540E+03 seconds
-> ad56004080g200170_all.img has 5143 counts
-> Exposure for ad56004080g200270_all.img is 9.600000000000000E+01 seconds
-> ad56004080g200270_all.img has 90 counts
-> Exposure for ad56004080g200370_all.img is 2.400064909130335E+03 seconds
-> ad56004080g200370_all.img has 2466 counts
-> Exposure for ad56004080g300170_all.img is 4.822034894853830E+03 seconds
-> ad56004080g300170_all.img has 5441 counts
-> Exposure for ad56004080g300270_all.img is 9.600000000000000E+01 seconds
-> ad56004080g300270_all.img has 110 counts
-> Exposure for ad56004080g300370_all.img is 2.400064909130335E+03 seconds
-> ad56004080g300370_all.img has 2764 counts
-> Summing the following images to produce ad56004080gis25670_all.totsky

ad56004080g200170_all.img
ad56004080g200270_all.img
ad56004080g200370_all.img
ad56004080g300170_all.img
ad56004080g300270_all.img
ad56004080g300370_all.img

-> Setting EXPOSURE=14638.19960168 in ad56004080gis25670_all.totsky
-> Setting TOTCTS=16014 in ad56004080gis25670_all.totsky
-> Exposure for ad56004080g200170_lo.img is 4.824034888565540E+03 seconds
-> ad56004080g200170_lo.img has 1178 counts
-> Exposure for ad56004080g200270_lo.img is 9.600000000000000E+01 seconds
-> ad56004080g200270_lo.img has 27 counts
-> Exposure for ad56004080g200370_lo.img is 2.400064909130335E+03 seconds
-> ad56004080g200370_lo.img has 579 counts
-> Exposure for ad56004080g300170_lo.img is 4.822034894853830E+03 seconds
-> ad56004080g300170_lo.img has 1185 counts
-> Exposure for ad56004080g300270_lo.img is 9.600000000000000E+01 seconds
-> ad56004080g300270_lo.img has 24 counts
-> Exposure for ad56004080g300370_lo.img is 2.400064909130335E+03 seconds
-> ad56004080g300370_lo.img has 632 counts
-> Summing the following images to produce ad56004080gis25670_lo.totsky

ad56004080g200170_lo.img
ad56004080g200270_lo.img
ad56004080g200370_lo.img
ad56004080g300170_lo.img
ad56004080g300270_lo.img
ad56004080g300370_lo.img

-> Setting EXPOSURE=14638.19960168 in ad56004080gis25670_lo.totsky
-> Setting TOTCTS=3625 in ad56004080gis25670_lo.totsky
-> Exposure for ad56004080g200170_hi.img is 4.824034888565540E+03 seconds
-> ad56004080g200170_hi.img has 3989 counts
-> Exposure for ad56004080g200270_hi.img is 9.600000000000000E+01 seconds
-> ad56004080g200270_hi.img has 63 counts
-> Exposure for ad56004080g200370_hi.img is 2.400064909130335E+03 seconds
-> ad56004080g200370_hi.img has 1892 counts
-> Exposure for ad56004080g300170_hi.img is 4.822034894853830E+03 seconds
-> ad56004080g300170_hi.img has 4278 counts
-> Exposure for ad56004080g300270_hi.img is 9.600000000000000E+01 seconds
-> ad56004080g300270_hi.img has 86 counts
-> Exposure for ad56004080g300370_hi.img is 2.400064909130335E+03 seconds
-> ad56004080g300370_hi.img has 2141 counts
-> Summing the following images to produce ad56004080gis25670_hi.totsky

ad56004080g200170_hi.img
ad56004080g200270_hi.img
ad56004080g200370_hi.img
ad56004080g300170_hi.img
ad56004080g300270_hi.img
ad56004080g300370_hi.img

-> Setting EXPOSURE=14638.19960168 in ad56004080gis25670_hi.totsky
-> Setting TOTCTS=12449 in ad56004080gis25670_hi.totsky
-> Running XIMAGE to create ad56004080gis25670.gif
-> Standard Output From STOOL ximage:

 No of detectors read in:   21
![1]XIMAGE> read/fits ad56004080gis25670_all.totsky
 Telescope ASCA GIS2,GIS3
 Image size = 256 x 256 pixels
 Image rebin = 1
 Image center = 128.5, 128.5
 Reading an image
  Image level, min = 0.0000000 max = 6.0000000
 Saving current map
![2]XIMAGE> read/expo ad56004080gis25670.totexpo
 Telescope ASCA GIS2,GIS3
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 243.96999
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.36837
  Scaling factor :     8.33333
  Min and max :   0  14
 Max-preserving scaling factor :     3.5714284
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     90041.6
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit

Detecting sources in summed images (8:38:18)

-> Smoothing ad56004080gis25670_all.totsky with ad56004080gis25670.totexpo
-> Clipping exposures below 2195.7300291 seconds
-> Detecting sources in ad56004080gis25670_all.smooth
-> Standard Output From STOOL ascasource:

107 213 0.000124317 179 36 4.30116

-> Smoothing ad56004080gis25670_hi.totsky with ad56004080gis25670.totexpo
-> Clipping exposures below 2195.7300291 seconds
-> Detecting sources in ad56004080gis25670_hi.smooth
-> Standard Output From STOOL ascasource:

106 211 0.000114126 177 89 5.68223

-> Smoothing ad56004080gis25670_lo.totsky with ad56004080gis25670.totexpo
-> Clipping exposures below 2195.7300291 seconds
-> Detecting sources in ad56004080gis25670_lo.smooth
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:

107 213 36 T

-> Sources with radius >= 2

107 213 36 T

-> Standard Output From STOOL colorpic:

color plane 0
color plane 1
color plane 2
writing image
image written

-> Creating fits catalog of sources: ad56004080gis25670.src
-> Smoothing ad56004080sis32002_all.totsky with ad56004080sis32002.totexpo
-> Clipping exposures below 1996.41701895 seconds
-> Detecting sources in ad56004080sis32002_all.smooth
-> Smoothing ad56004080sis32002_hi.totsky with ad56004080sis32002.totexpo
-> Clipping exposures below 1996.41701895 seconds
-> Detecting sources in ad56004080sis32002_hi.smooth
-> Smoothing ad56004080sis32002_lo.totsky with ad56004080sis32002.totexpo
-> Clipping exposures below 1996.41701895 seconds
-> Detecting sources in ad56004080sis32002_lo.smooth
-> Determining extraction radii
-> Eliminating redundant sources
-> Sources with radius >= 2

-> Standard Output From STOOL colorpic:

color plane 0
color plane 1
color plane 2
writing image
image written

-> Creating fits catalog of sources: ad56004080sis32002.src
-> Generating region files
-> Converting (107.0,213.0,2.0) to g2 detector coordinates
-> Using events in: ad56004080g200170h.evt
-> No photons in 2.0 pixel radius
-> Converting (107.0,213.0,36.0) to g2 detector coordinates
-> Using events in: ad56004080g200170h.evt
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   23895.000
 The mean of the selected column is                  58.138686
 The standard deviation of the selected column is    8.3518794
 The minimum of selected column is                   42.000000
 The maximum of selected column is                   74.000000
 The number of points used in calculation is              411

-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   48233.000
 The mean of the selected column is                  117.35523
 The standard deviation of the selected column is    14.920777
 The minimum of selected column is                   84.000000
 The maximum of selected column is                   150.00000
 The number of points used in calculation is              411

-> Converting (107.0,213.0,2.0) to g3 detector coordinates
-> Using events in: ad56004080g300170h.evt
-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   263.00000
 The mean of the selected column is                  43.833333
 The standard deviation of the selected column is    1.1690452
 The minimum of selected column is                   42.000000
 The maximum of selected column is                   45.000000
 The number of points used in calculation is                6

-> Standard Output From FTOOL fstatistic:

 The sum of the selected column is                   694.00000
 The mean of the selected column is                  115.66667
 The standard deviation of the selected column is   0.51639778
 The minimum of selected column is                   115.00000
 The maximum of selected column is                   116.00000
 The number of points used in calculation is                6

Extracting spectra and generating response matrices (8:46:25)

-> Fetching xrt_ea_v2_0.fits
-> Fetching xrt_psf_v2_0.fits
-> sisph2pi_110397.fits already present in current directory
-> Fetching sisechos_290296.fits
-> Fetching sisrddis_290296.fits
-> Standard Output From STOOL group_event_files:

1 ad56004080s000202h.evt 1687
1 ad56004080s000302m.evt 1687
2 ad56004080s000102h.evt 31

-> Fetching SIS0_NOTCHIP0.1
-> Fetching SIS0_NOTCHIP3.1
-> Fetching SIS0_OFFCHIP.2
-> Extracting ad56004080s010102_0.pi from ad56004080s032002_0.reg and:

ad56004080s000202h.evt
ad56004080s000302m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.18E+04      459 0110
      2 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228      1195             33         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       446             13         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1687      1641             46         0         0         0
   in  6673.8     seconds
 Spectrum         has     1641 counts for 0.2459     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20974         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s010102_0.pi
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228      1195             33         0         0         0
 Writing events file
   1195 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       446             13         0         0         0
 Writing events file
   1641 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1687      1641             46         0         0         0
   in  6673.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad56004080s000302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad56004080s010102_0.pi group=yes
Wrote spectrum to ad56004080s010102_0.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Deleting BLANK keyword from ad56004080s010102_0.pi
-> Grouping ad56004080s010102_0.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20974         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      16  of undefined grouping (Channel quality=bad)
 ...        17 -      34  are grouped by a factor       18
 ...        35 -      41  are grouped by a factor        7
 ...        42 -      47  are grouped by a factor        6
 ...        48 -      51  are grouped by a factor        4
 ...        52 -      57  are grouped by a factor        6
 ...        58 -      61  are grouped by a factor        4
 ...        62 -      64  are grouped by a factor        3
 ...        65 -      69  are grouped by a factor        5
 ...        70 -      73  are grouped by a factor        4
 ...        74 -      83  are grouped by a factor        5
 ...        84 -      91  are grouped by a factor        4
 ...        92 -      96  are grouped by a factor        5
 ...        97 -     116  are grouped by a factor        4
 ...       117 -     121  are grouped by a factor        5
 ...       122 -     133  are grouped by a factor        4
 ...       134 -     143  are grouped by a factor        5
 ...       144 -     149  are grouped by a factor        6
 ...       150 -     153  are grouped by a factor        4
 ...       154 -     159  are grouped by a factor        6
 ...       160 -     166  are grouped by a factor        7
 ...       167 -     172  are grouped by a factor        6
 ...       173 -     179  are grouped by a factor        7
 ...       180 -     187  are grouped by a factor        8
 ...       188 -     200  are grouped by a factor       13
 ...       201 -     215  are grouped by a factor       15
 ...       216 -     226  are grouped by a factor       11
 ...       227 -     241  are grouped by a factor       15
 ...       242 -     280  are grouped by a factor       39
 ...       281 -     428  are grouped by a factor      148
 ...       429 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s010102_0.pi
 ** grppha 2.9.0 completed successfully

-> Source occupies chip(s) 1 2
-> Fetching SIS0_NOTCHIP2.1
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.67E+04     1641 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1641       948            693         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1641       948            693         0         0         0
   in  6673.8     seconds
 Spectrum         has      948 counts for 0.1420     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10462         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Fetching sis0c1p40_290296.fits
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data files:
  ecd = ./sis0c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Fetching SIS0_NOTCHIP1.1
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.67E+04     1641 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1641       693            948         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1641       693            948         0         0         0
   in  6673.8     seconds
 Spectrum         has      693 counts for 0.1038     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10512         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Fetching sis0c2p40_290296.fits
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C2 Bright PI RMF
Calibration data files:
  ecd = ./sis0c2p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Chip weights:

rmf1.tmp 0.577696526508227
rmf2.tmp 0.422303473491773

-> Standard Output From FTOOL addrmf:

ADDRMF vers 1.14  11 February 1999.
Summing ...
 5.777E-01 * rmf1.tmp
 4.223E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.58
              ASCA       SIS0       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.42
              ASCA       SIS0       NONE       NONE       PI
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ...  using wtrmf4 1.4.0
 ...... wtrmf4 Old format requested: 1.2.0
 ...... Resetting format (HDUVERS) to 1.3.0
 ... new extension created
 ...  Max # elements in F_CHAN & N_CHAN arrays =        2
 ...  Max # elements in MATRIX array =      423
 ... Using Variable length array for MATRIX column
 ... written the extension header keywords
 ... written the OGIP required keywords
 ... written the history keywords
 ... written the comment keywords
 ... defined the data structure
 ... successfully written RSP_MATRIX data

-> Generating ad56004080s010102_0.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size  105 by   53 bins
               expanded to  105 by   53 bins
 First WMAP bin is at detector pixel  232  216
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   241.68     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.63600E+03
 Weighted mean angle from optical axis  =  7.246 arcmin

-> Standard Output From STOOL group_event_files:

1 ad56004080s000212h.evt 1818
1 ad56004080s000312m.evt 1818
2 ad56004080s000112h.evt 33

-> SIS0_NOTCHIP0.1 already present in current directory
-> SIS0_NOTCHIP3.1 already present in current directory
-> SIS0_OFFCHIP.2 already present in current directory
-> Extracting ad56004080s010212_0.pi from ad56004080s032002_0.reg and:

ad56004080s000212h.evt
ad56004080s000312m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1328 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.18E+04      490 0110
      2 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1328 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000212h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1328      1295             33         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            490       478             12         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1818      1773             45         0         0         0
   in  6673.8     seconds
 Spectrum         has     1773 counts for 0.2657     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20974         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      31  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s010212_0.pi
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000212h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1328      1295             33         0         0         0
 Writing events file
   1295 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            490       478             12         0         0         0
 Writing events file
   1773 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1818      1773             45         0         0         0
   in  6673.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000212h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > read events ad56004080s000312m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad56004080s010212_0.pi group=yes
Wrote spectrum to ad56004080s010212_0.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Deleting BLANK keyword from ad56004080s010212_0.pi
-> Grouping ad56004080s010212_0.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20974         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      31  of undefined grouping (Channel quality=bad)
 ...        32 -      69  are grouped by a factor       38
 ...        70 -      83  are grouped by a factor       14
 ...        84 -      94  are grouped by a factor       11
 ...        95 -     101  are grouped by a factor        7
 ...       102 -     111  are grouped by a factor       10
 ...       112 -     119  are grouped by a factor        8
 ...       120 -     125  are grouped by a factor        6
 ...       126 -     135  are grouped by a factor       10
 ...       136 -     143  are grouped by a factor        8
 ...       144 -     152  are grouped by a factor        9
 ...       153 -     163  are grouped by a factor       11
 ...       164 -     171  are grouped by a factor        8
 ...       172 -     177  are grouped by a factor        6
 ...       178 -     187  are grouped by a factor       10
 ...       188 -     194  are grouped by a factor        7
 ...       195 -     202  are grouped by a factor        8
 ...       203 -     209  are grouped by a factor        7
 ...       210 -     225  are grouped by a factor        8
 ...       226 -     231  are grouped by a factor        6
 ...       232 -     255  are grouped by a factor        8
 ...       256 -     265  are grouped by a factor       10
 ...       266 -     274  are grouped by a factor        9
 ...       275 -     282  are grouped by a factor        8
 ...       283 -     292  are grouped by a factor       10
 ...       293 -     300  are grouped by a factor        8
 ...       301 -     310  are grouped by a factor       10
 ...       311 -     319  are grouped by a factor        9
 ...       320 -     333  are grouped by a factor       14
 ...       334 -     344  are grouped by a factor       11
 ...       345 -     357  are grouped by a factor       13
 ...       358 -     371  are grouped by a factor       14
 ...       372 -     390  are grouped by a factor       19
 ...       391 -     412  are grouped by a factor       22
 ...       413 -     441  are grouped by a factor       29
 ...       442 -     459  are grouped by a factor       18
 ...       460 -     489  are grouped by a factor       30
 ...       490 -     549  are grouped by a factor       60
 ...       550 -     668  are grouped by a factor      119
 ...       669 -    1023  are grouped by a factor      355
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s010212_0.pi
 ** grppha 2.9.0 completed successfully

-> Source occupies chip(s) 1 2
-> SIS0_NOTCHIP2.1 already present in current directory
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:44:52    0.67E+04     1773 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1773      1032            741         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1773      1032            741         0         0         0
   in  6673.8     seconds
 Spectrum         has     1032 counts for 0.1546     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10462         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      31  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> sis0c1p40_290296.fits already present in current directory
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data files:
  ecd = ./sis0c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> SIS0_NOTCHIP1.1 already present in current directory
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:44:52    0.67E+04     1773 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1773       741           1032         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1773       741           1032         0         0         0
   in  6673.8     seconds
 Spectrum         has      741 counts for 0.1110     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6673.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10512         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      31  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> sis0c2p40_290296.fits already present in current directory
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C2 Bright2 PI RMF
Calibration data files:
  ecd = ./sis0c2p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Chip weights:

rmf1.tmp 0.582064297800338
rmf2.tmp 0.417935702199662

-> Standard Output From FTOOL addrmf:

ADDRMF vers 1.14  11 February 1999.
Summing ...
 5.821E-01 * rmf1.tmp
 4.179E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.58
              ASCA       SIS0       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.42
              ASCA       SIS0       NONE       NONE       PI
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ...  using wtrmf4 1.4.0
 ...... wtrmf4 Old format requested: 1.2.0
 ...... Resetting format (HDUVERS) to 1.3.0
 ... new extension created
 ...  Max # elements in F_CHAN & N_CHAN arrays =        2
 ...  Max # elements in MATRIX array =      827
 ... Using Variable length array for MATRIX column
 ... written the extension header keywords
 ... written the OGIP required keywords
 ... written the history keywords
 ... written the comment keywords
 ... defined the data structure
 ... successfully written RSP_MATRIX data

-> Generating ad56004080s010212_0.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size  106 by   53 bins
               expanded to  106 by   53 bins
 First WMAP bin is at detector pixel  232  216
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   241.68     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.76400E+03
 Weighted mean angle from optical axis  =  7.214 arcmin

-> Standard Output From STOOL group_event_files:

1 ad56004080s100102h.evt 1422
1 ad56004080s100202m.evt 1422

-> Fetching SIS1_NOTCHIP0.1
-> Fetching SIS1_NOTCHIP3.1
-> Fetching SIS1_OFFCHIP.2
-> Extracting ad56004080s110102_0.pi from ad56004080s132002_0.reg and:

ad56004080s100102h.evt
ad56004080s100202m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.17E+04      375 0110
      2 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047      1025             22         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       365             10         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1422      1390             32         0         0         0
   in  6549.8     seconds
 Spectrum         has     1390 counts for 0.2122     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20872         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s110102_0.pi
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047      1025             22         0         0         0
 Writing events file
   1025 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       365             10         0         0         0
 Writing events file
   1390 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1422      1390             32         0         0         0
   in  6549.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad56004080s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad56004080s110102_0.pi group=yes
Wrote spectrum to ad56004080s110102_0.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Deleting BLANK keyword from ad56004080s110102_0.pi
-> Grouping ad56004080s110102_0.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20872         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      16  of undefined grouping (Channel quality=bad)
 ...        17 -      32  are grouped by a factor       16
 ...        33 -      42  are grouped by a factor       10
 ...        43 -      48  are grouped by a factor        6
 ...        49 -      53  are grouped by a factor        5
 ...        54 -      69  are grouped by a factor        4
 ...        70 -      72  are grouped by a factor        3
 ...        73 -      77  are grouped by a factor        5
 ...        78 -      83  are grouped by a factor        6
 ...        84 -      88  are grouped by a factor        5
 ...        89 -     100  are grouped by a factor        6
 ...       101 -     110  are grouped by a factor        5
 ...       111 -     116  are grouped by a factor        6
 ...       117 -     123  are grouped by a factor        7
 ...       124 -     147  are grouped by a factor        6
 ...       148 -     154  are grouped by a factor        7
 ...       155 -     163  are grouped by a factor        9
 ...       164 -     183  are grouped by a factor       10
 ...       184 -     196  are grouped by a factor       13
 ...       197 -     219  are grouped by a factor       23
 ...       220 -     236  are grouped by a factor       17
 ...       237 -     259  are grouped by a factor       23
 ...       260 -     308  are grouped by a factor       49
 ...       309 -     456  are grouped by a factor      148
 ...       457 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s110102_0.pi
 ** grppha 2.9.0 completed successfully

-> Source occupies chip(s) 1 2
-> Fetching SIS1_NOTCHIP2.1
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.65E+04     1390 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1390       638            752         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1390       638            752         0         0         0
   in  6549.8     seconds
 Spectrum         has      638 counts for 9.7408E-02 counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10410         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Fetching sis1c1p40_290296.fits
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C1 Bright PI RMF
Calibration data files:
  ecd = ./sis1c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Fetching SIS1_NOTCHIP1.1
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.65E+04     1390 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1390       752            638         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1390       752            638         0         0         0
   in  6549.8     seconds
 Spectrum         has      752 counts for 0.1148     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10462         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Fetching sis1c2p40_290296.fits
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C2 Bright PI RMF
Calibration data files:
  ecd = ./sis1c2p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Chip weights:

rmf1.tmp 0.458992805755396
rmf2.tmp 0.541007194244604

-> Standard Output From FTOOL addrmf:

ADDRMF vers 1.14  11 February 1999.
Summing ...
 4.590E-01 * rmf1.tmp
 5.410E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.46
              ASCA       SIS1       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.54
              ASCA       SIS1       NONE       NONE       PI
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ...  using wtrmf4 1.4.0
 ...... wtrmf4 Old format requested: 1.2.0
 ...... Resetting format (HDUVERS) to 1.3.0
 ... new extension created
 ...  Max # elements in F_CHAN & N_CHAN arrays =        2
 ...  Max # elements in MATRIX array =      423
 ... Using Variable length array for MATRIX column
 ... written the extension header keywords
 ... written the OGIP required keywords
 ... written the history keywords
 ... written the comment keywords
 ... defined the data structure
 ... successfully written RSP_MATRIX data

-> Generating ad56004080s110102_0.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size  105 by   53 bins
               expanded to  105 by   53 bins
 First WMAP bin is at detector pixel  232  664
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   240.51     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.37900E+03
 Weighted mean angle from optical axis  =  6.650 arcmin

-> Standard Output From STOOL group_event_files:

1 ad56004080s100112h.evt 1490
1 ad56004080s100212m.evt 1490

-> SIS1_NOTCHIP0.1 already present in current directory
-> SIS1_NOTCHIP3.1 already present in current directory
-> SIS1_OFFCHIP.2 already present in current directory
-> Extracting ad56004080s110212_0.pi from ad56004080s132002_0.reg and:

ad56004080s100112h.evt
ad56004080s100212m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1100 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.17E+04      390 0110
      2 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1100 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1100      1077             23         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            390       381              9         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1490      1458             32         0         0         0
   in  6549.8     seconds
 Spectrum         has     1458 counts for 0.2226     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20872         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      32  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s110212_0.pi
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1100      1077             23         0         0         0
 Writing events file
   1077 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            390       381              9         0         0         0
 Writing events file
   1458 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1490      1458             32         0         0         0
   in  6549.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > read events ad56004080s100212m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad56004080s110212_0.pi group=yes
Wrote spectrum to ad56004080s110212_0.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Deleting BLANK keyword from ad56004080s110212_0.pi
-> Grouping ad56004080s110212_0.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.20872         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      32  of undefined grouping (Channel quality=bad)
 ...        33 -      64  are grouped by a factor       32
 ...        65 -      83  are grouped by a factor       19
 ...        84 -     103  are grouped by a factor       10
 ...       104 -     111  are grouped by a factor        8
 ...       112 -     125  are grouped by a factor        7
 ...       126 -     133  are grouped by a factor        8
 ...       134 -     142  are grouped by a factor        9
 ...       143 -     150  are grouped by a factor        8
 ...       151 -     159  are grouped by a factor        9
 ...       160 -     170  are grouped by a factor       11
 ...       171 -     178  are grouped by a factor        8
 ...       179 -     191  are grouped by a factor       13
 ...       192 -     211  are grouped by a factor       10
 ...       212 -     219  are grouped by a factor        8
 ...       220 -     230  are grouped by a factor       11
 ...       231 -     243  are grouped by a factor       13
 ...       244 -     267  are grouped by a factor       12
 ...       268 -     289  are grouped by a factor       11
 ...       290 -     303  are grouped by a factor       14
 ...       304 -     333  are grouped by a factor       15
 ...       334 -     351  are grouped by a factor       18
 ...       352 -     372  are grouped by a factor       21
 ...       373 -     397  are grouped by a factor       25
 ...       398 -     438  are grouped by a factor       41
 ...       439 -     467  are grouped by a factor       29
 ...       468 -     512  are grouped by a factor       45
 ...       513 -     590  are grouped by a factor       78
 ...       591 -     775  are grouped by a factor      185
 ...       776 -    1023  are grouped by a factor      248
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080s110212_0.pi
 ** grppha 2.9.0 completed successfully

-> Source occupies chip(s) 1 2
-> SIS1_NOTCHIP2.1 already present in current directory
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:44:52    0.65E+04     1458 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1458       655            803         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1458       655            803         0         0         0
   in  6549.8     seconds
 Spectrum         has      655 counts for 0.1000     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10410         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      32  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> sis1c1p40_290296.fits already present in current directory
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C1 Bright2 PI RMF
Calibration data files:
  ecd = ./sis1c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> SIS1_NOTCHIP1.1 already present in current directory
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:44:52    0.65E+04     1458 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1458       803            655         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1458       803            655         0         0         0
   in  6549.8     seconds
 Spectrum         has      803 counts for 0.1226     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 6549.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 0.10462         Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      32  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> sis1c2p40_290296.fits already present in current directory
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:

Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C2 Bright2 PI RMF
Calibration data files:
  ecd = ./sis1c2p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.

-> Chip weights:

rmf1.tmp 0.449245541838134
rmf2.tmp 0.550754458161866

-> Standard Output From FTOOL addrmf:

ADDRMF vers 1.14  11 February 1999.
Summing ...
 4.492E-01 * rmf1.tmp
 5.508E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.45
              ASCA       SIS1       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.55
              ASCA       SIS1       NONE       NONE       PI
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ... using rdrmf4 1.3.2
 WARNING - rdrmf4 1.3.2: Problem reading DETNAM keyword
 ... fitsio 2.035 error message: keyword not found in header
 WARNING - rdrmf4 1.3.2: Problem reading EFFAREA keyword
 ... fitsio 2.035 error message: keyword not found in header
 ... read all the keywords
 ... reading the data
 ... successfully read RSP_MATRIX data
 ...  using wtrmf4 1.4.0
 ...... wtrmf4 Old format requested: 1.2.0
 ...... Resetting format (HDUVERS) to 1.3.0
 ... new extension created
 ...  Max # elements in F_CHAN & N_CHAN arrays =        2
 ...  Max # elements in MATRIX array =      834
 ... Using Variable length array for MATRIX column
 ... written the extension header keywords
 ... written the OGIP required keywords
 ... written the history keywords
 ... written the comment keywords
 ... defined the data structure
 ... successfully written RSP_MATRIX data

-> Generating ad56004080s110212_0.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size  105 by   53 bins
               expanded to  105 by   53 bins
 First WMAP bin is at detector pixel  232  664
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   240.51     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.44700E+03
 Weighted mean angle from optical axis  =  6.631 arcmin

-> Standard Output From STOOL group_event_files:

1 ad56004080g200170h.evt 7796
1 ad56004080g200270l.evt 7796
1 ad56004080g200370m.evt 7796

-> GIS2_REGION256.4 already present in current directory
-> Extracting ad56004080g210170_1.pi from ad56004080g225670_1.reg and:

ad56004080g200170h.evt
ad56004080g200270l.evt
ad56004080g200370m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2506     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199       816           4383         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        18             73         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506       393           2113         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7796      1227           6569         0         0         0
   in  7320.1     seconds
 Spectrum         has     1227 counts for 0.1676     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 7320.1          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.81410E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g210170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad56004080g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad56004080g210170_1.pi group=yes
Wrote spectrum to ad56004080g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Deleting BLANK keyword from ad56004080g210170_1.pi
-> Correcting ad56004080g210170_1.pi for dead time
-> Standard Output From FTOOL deadtime:

... read all the files from deadlist.tmp

-> Grouping ad56004080g210170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 7169.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.81410E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      72  are grouped by a factor       73
 ...        73 -     106  are grouped by a factor       34
 ...       107 -     137  are grouped by a factor       31
 ...       138 -     153  are grouped by a factor       16
 ...       154 -     167  are grouped by a factor       14
 ...       168 -     179  are grouped by a factor       12
 ...       180 -     207  are grouped by a factor       14
 ...       208 -     225  are grouped by a factor       18
 ...       226 -     236  are grouped by a factor       11
 ...       237 -     256  are grouped by a factor       20
 ...       257 -     271  are grouped by a factor       15
 ...       272 -     285  are grouped by a factor       14
 ...       286 -     298  are grouped by a factor       13
 ...       299 -     315  are grouped by a factor       17
 ...       316 -     328  are grouped by a factor       13
 ...       329 -     344  are grouped by a factor       16
 ...       345 -     359  are grouped by a factor       15
 ...       360 -     379  are grouped by a factor       20
 ...       380 -     398  are grouped by a factor       19
 ...       399 -     416  are grouped by a factor       18
 ...       417 -     440  are grouped by a factor       24
 ...       441 -     467  are grouped by a factor       27
 ...       468 -     525  are grouped by a factor       29
 ...       526 -     555  are grouped by a factor       30
 ...       556 -     589  are grouped by a factor       34
 ...       590 -     643  are grouped by a factor       54
 ...       644 -     730  are grouped by a factor       87
 ...       731 -    1023  are grouped by a factor      293
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g210170_1.pi
 ** grppha 2.9.0 completed successfully

-> Fetching gis2v4_0.rmf
-> Fetching s2bev1.fits
-> Fetching s2gridv3.fits
-> Generating ad56004080g210170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   53 by   72 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel    5   54
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   190.28     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.21700E+03
 Weighted mean angle from optical axis  = 17.021 arcmin

-> Standard Output From STOOL group_event_files:

1 ad56004080g300170h.evt 8434
1 ad56004080g300270l.evt 8434
1 ad56004080g300370m.evt 8434

-> GIS3_REGION256.4 already present in current directory
-> Extracting ad56004080g310170_1.pi from ad56004080g325670_1.reg and:

ad56004080g300170h.evt
ad56004080g300270l.evt
ad56004080g300370m.evt

-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2808     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515       666           4849         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111        11            100         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808       335           2473         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8434      1012           7422         0         0         0
   in  7318.1     seconds
 Spectrum         has     1012 counts for 0.1383     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 7318.1          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.26540E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g310170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad56004080g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad56004080g310170_1.pi group=yes
Wrote spectrum to ad56004080g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Deleting BLANK keyword from ad56004080g310170_1.pi
-> Correcting ad56004080g310170_1.pi for dead time
-> Standard Output From FTOOL deadtime:

... read all the files from deadlist.tmp

-> Grouping ad56004080g310170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:

 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 7189.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.26540E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      67  are grouped by a factor       68
 ...        68 -     113  are grouped by a factor       46
 ...       114 -     144  are grouped by a factor       31
 ...       145 -     163  are grouped by a factor       19
 ...       164 -     181  are grouped by a factor       18
 ...       182 -     203  are grouped by a factor       22
 ...       204 -     220  are grouped by a factor       17
 ...       221 -     240  are grouped by a factor       20
 ...       241 -     278  are grouped by a factor       19
 ...       279 -     293  are grouped by a factor       15
 ...       294 -     327  are grouped by a factor       17
 ...       328 -     347  are grouped by a factor       20
 ...       348 -     363  are grouped by a factor       16
 ...       364 -     385  are grouped by a factor       22
 ...       386 -     411  are grouped by a factor       26
 ...       412 -     436  are grouped by a factor       25
 ...       437 -     468  are grouped by a factor       32
 ...       469 -     496  are grouped by a factor       28
 ...       497 -     544  are grouped by a factor       48
 ...       545 -     585  are grouped by a factor       41
 ...       586 -     644  are grouped by a factor       59
 ...       645 -     785  are grouped by a factor      141
 ...       786 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g310170_1.pi
 ** grppha 2.9.0 completed successfully

-> Fetching gis3v4_0.rmf
-> Fetching s3bev1.fits
-> Fetching s3gridv3.fits
-> Generating ad56004080g310170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:

ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   39 by   71 bins
               expanded to   64 by  128 bins
 First WMAP bin is at detector pixel   30   54
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   129.06     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.00200E+03
 Weighted mean angle from optical axis  = 15.996 arcmin

-> Plotting ad56004080g210170_1_pi.ps from ad56004080g210170_1.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:21:39 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080g210170_1.pi;
 Net count rate (cts/s) for file   1  0.1711    +/-  4.8857E-03
   using response (RMF) file...       gis2v4_0.rmf
   using auxiliary (ARF) file...      ad56004080g210170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Plotting ad56004080g310170_1_pi.ps from ad56004080g310170_1.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:21:56 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080g310170_1.pi;
 Net count rate (cts/s) for file   1  0.1408    +/-  4.8725E-03
   using response (RMF) file...       gis3v4_0.rmf
   using auxiliary (ARF) file...      ad56004080g310170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Plotting ad56004080s010102_0_pi.ps from ad56004080s010102_0.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:22:13 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080s010102_0.pi;
 Net count rate (cts/s) for file   1  0.2459    +/-  6.2449E-03
   using response (RMF) file...       ad56004080s010102_0.rmf
   using auxiliary (ARF) file...      ad56004080s010102_0.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Plotting ad56004080s010212_0_pi.ps from ad56004080s010212_0.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:22:30 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080s010212_0.pi;
 Net count rate (cts/s) for file   1  0.2657    +/-  6.3659E-03
   using response (RMF) file...       ad56004080s010212_0.rmf
   using auxiliary (ARF) file...      ad56004080s010212_0.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Plotting ad56004080s110102_0_pi.ps from ad56004080s110102_0.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:22:51 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080s110102_0.pi;
 Net count rate (cts/s) for file   1  0.2122    +/-  5.8258E-03
   using response (RMF) file...       ad56004080s110102_0.rmf
   using auxiliary (ARF) file...      ad56004080s110102_0.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Plotting ad56004080s110212_0_pi.ps from ad56004080s110212_0.pi
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:23:09 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad56004080s110212_0.pi;
 Net count rate (cts/s) for file   1  0.2226    +/-  5.8954E-03
   using response (RMF) file...       ad56004080s110212_0.rmf
   using auxiliary (ARF) file...      ad56004080s110212_0.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

Extracting light curves (9:23:14)

-> TIMEDEL=8.0000000000E+00 for ad56004080s000102h.evt
-> TIMEDEL=8.0000000000E+00 for ad56004080s000202h.evt
-> TIMEDEL=8.0000000000E+00 for ad56004080s000302m.evt
-> Minimum bin size is 8.0000000000E+00 seconds
-> Extracting events from region ad56004080s032002_0.reg
-> ... and files: ad56004080s000102h.evt ad56004080s000202h.evt ad56004080s000302m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.86E+02       31 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
      2 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.86E+02       31 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.18E+04      459 0110
      2 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
      3 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.86E+02       31 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             31        31              0         0         0         0
 Writing events file
     31 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228      1228              0         0         0         0
 Writing events file
   1259 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       459              0         0         0         0
 Writing events file
   1718 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1718      1718              0         0         0         0
   in  6759.6     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad56004080s000202h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad56004080s000302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Extracting ad56004080s000002_0.lc with binsize 196.730089454767
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.68E+04     1718 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1718      1718              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1718      1718              0         0         0         0
   in  6759.6     seconds
 Fits light curve has     1718 counts for 0.2542     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 196.730089454767
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad56004080s000002_0.lc
Wrote FITS light curve to file ad56004080s000002_0.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Plotting ad56004080s000002_0.lc in ad56004080s000002_0_lc.ps
-> Standard Output From FTOOL lcurve:

 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad56004080s000002_0.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ GC REGION 2         Start Time (d) .... 11067 12:26:06.638
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 11067 18:49:02.638
 No. of Rows .......           38        Bin Time (s) ......    196.7
 Right Ascension ... 2.6556E+02          Internal time sys.. Converted to TJD
 Declination ....... -3.0129E+01         Experiment ........ ASCA     SIS0
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 11067.51813238430  (days)      12:26: 6:638  (h:m:s:ms)
 Expected Stop .... 11067.78405831023  (days)      18:49: 2:638  (h:m:s:ms)
 
 Minimum Newbin Time    196.73009      (s)
 for Maximum Newbin No..              117
 
 Default Newbin Time is:   196.73009    (s) (to have 1 Intv. of     117 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     196.73009      (s)
 Maximum Newbin No.               117
 
 Default Newbins per Interval are:       117
 (giving       1 Interval of       117 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       117 Newbins of       196.730     (s)
 
     117 analysis results per interval
 
  2% completed
  5% completed
  7% completed
 10% completed
 13% completed
 15% completed
 18% completed
 21% completed
 23% completed
 26% completed
 28% completed
 31% completed
 34% completed
 36% completed
 39% completed
 42% completed
 44% completed
 47% completed
 50% completed
 52% completed
 55% completed
 57% completed
 60% completed
 63% completed
 65% completed
 68% completed
 71% completed
 73% completed
 76% completed
 78% completed
 81% completed
 84% completed
 86% completed
 89% completed
 92% completed
 94% completed
 97% completed
100% completed
 
 Intv    1   Start 11067 13:30: 2
     Ser.1     Avg 0.2496        Chisq  32.38       Var 0.1320E-02 Newbs.     38
               Min 0.1753          Max 0.3101    expVar 0.1572E-02  Bins     38
PLT> @lightcurve.pco
!PLT> dev ad56004080s000002_0_lc.ps/ps
!PLT> LA File ad56004080s000002_0.lc
!PLT> plot
!PLT> quit

-> TIMEDEL=8.0000000000E+00 for ad56004080s100102h.evt
-> TIMEDEL=8.0000000000E+00 for ad56004080s100202m.evt
-> Minimum bin size is 8.0000000000E+00 seconds
-> Extracting events from region ad56004080s132002_0.reg
-> ... and files: ad56004080s100102h.evt ad56004080s100202m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.17E+04      375 0110
      2 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047      1047              0         0         0         0
 Writing events file
   1047 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       375              0         0         0         0
 Writing events file
   1422 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1422      1422              0         0         0         0
   in  6549.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad56004080s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Extracting ad56004080s100002_0.lc with binsize 230.302386018336
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:44:52    0.65E+04     1422 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1422      1422              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1422      1422              0         0         0         0
   in  6549.8     seconds
 Fits light curve has     1422 counts for 0.2171     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 230.302386018336
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad56004080s100002_0.lc
Wrote FITS light curve to file ad56004080s100002_0.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Plotting ad56004080s100002_0.lc in ad56004080s100002_0_lc.ps
-> Standard Output From FTOOL lcurve:

 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad56004080s100002_0.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ GC REGION 2         Start Time (d) .... 11067 12:26:06.638
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 11067 18:48:30.638
 No. of Rows .......           31        Bin Time (s) ......    230.3
 Right Ascension ... 2.6556E+02          Internal time sys.. Converted to TJD
 Declination ....... -3.0129E+01         Experiment ........ ASCA     SIS1
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 11067.51813238430  (days)      12:26: 6:638  (h:m:s:ms)
 Expected Stop .... 11067.78368793986  (days)      18:48:30:638  (h:m:s:ms)
 
 Minimum Newbin Time    230.30238      (s)
 for Maximum Newbin No..              100
 
 Default Newbin Time is:   230.30238    (s) (to have 1 Intv. of     100 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     230.30238      (s)
 Maximum Newbin No.               100
 
 Default Newbins per Interval are:       100
 (giving       1 Interval of       100 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       100 Newbins of       230.302     (s)
 
     100 analysis results per interval
 
  3% completed
  6% completed
  9% completed
 12% completed
 16% completed
 19% completed
 22% completed
 25% completed
 29% completed
 32% completed
 35% completed
 38% completed
 41% completed
 45% completed
 48% completed
 51% completed
 54% completed
 58% completed
 61% completed
 64% completed
 67% completed
 70% completed
 74% completed
 77% completed
 80% completed
 83% completed
 87% completed
 90% completed
 93% completed
 96% completed
100% completed
 
 Intv    1   Start 11067 13:29:26
     Ser.1     Avg 0.2189        Chisq  26.75       Var 0.1014E-02 Newbs.     31
               Min 0.1563          Max 0.2736    expVar 0.1141E-02  Bins     31
PLT> @lightcurve.pco
!PLT> dev ad56004080s100002_0_lc.ps/ps
!PLT> LA File ad56004080s100002_0.lc
!PLT> plot
!PLT> quit

-> TIMEDEL=6.2500000000E-02 for ad56004080g200170h.evt
-> TIMEDEL=2.0000000000E+00 for ad56004080g200270l.evt
-> TIMEDEL=5.0000000000E-01 for ad56004080g200370m.evt
-> Minimum bin size is 2.0000000000E+00 seconds
-> Extracting events from region ad56004080g225670_1.reg
-> ... and files: ad56004080g200170h.evt ad56004080g200270l.evt ad56004080g200370m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2506     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199       816           4383         0         0         0
 Writing events file
    816 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        18             73         0         0         0
 Writing events file
    834 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506       393           2113         0         0         0
 Writing events file
   1227 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7796      1227           6569         0         0         0
   in  7320.1     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad56004080g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Extracting ad56004080g200070_1.lc with binsize 298.29257267733
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.73E+04     1227     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1227      1227              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1227      1227              0         0         0         0
   in  7320.1     seconds
 Fits light curve has     1227 counts for 0.1676     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set binsize 298.29257267733
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad56004080g200070_1.lc
Wrote FITS light curve to file ad56004080g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Plotting ad56004080g200070_1.lc in ad56004080g200070_1_lc.ps
-> Standard Output From FTOOL lcurve:

 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad56004080g200070_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ GC REGION 2         Start Time (d) .... 11067 12:26:06.638
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 11067 18:50:38.638
 No. of Rows .......           25        Bin Time (s) ......    298.3
 Right Ascension ... 2.6556E+02          Internal time sys.. Converted to TJD
 Declination ....... -3.0129E+01         Experiment ........ ASCA     GIS2
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 11067.51813238430  (days)      12:26: 6:638  (h:m:s:ms)
 Expected Stop .... 11067.78516942134  (days)      18:50:38:638  (h:m:s:ms)
 
 Minimum Newbin Time    298.29257      (s)
 for Maximum Newbin No..               78
 
 Default Newbin Time is:   298.29257    (s) (to have 1 Intv. of      78 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     298.29257      (s)
 Maximum Newbin No.                78
 
 Default Newbins per Interval are:        78
 (giving       1 Interval of        78 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with        78 Newbins of       298.293     (s)
 
      78 analysis results per interval
 
  4% completed
  8% completed
 12% completed
 16% completed
 20% completed
 24% completed
 28% completed
 32% completed
 36% completed
 40% completed
 44% completed
 48% completed
 52% completed
 56% completed
 60% completed
 64% completed
 68% completed
 72% completed
 76% completed
 80% completed
 84% completed
 88% completed
 92% completed
 96% completed
100% completed
 
 Intv    1   Start 11067 13:33:13
     Ser.1     Avg 0.1668        Chisq  26.94       Var 0.7870E-03 Newbs.     25
               Min 0.1249          Max 0.2404    expVar 0.6475E-03  Bins     25
PLT> @lightcurve.pco
!PLT> dev ad56004080g200070_1_lc.ps/ps
!PLT> LA File ad56004080g200070_1.lc
!PLT> plot
!PLT> quit

-> TIMEDEL=6.2500000000E-02 for ad56004080g300170h.evt
-> TIMEDEL=2.0000000000E+00 for ad56004080g300270l.evt
-> TIMEDEL=5.0000000000E-01 for ad56004080g300370m.evt
-> Minimum bin size is 2.0000000000E+00 seconds
-> Extracting events from region ad56004080g325670_1.reg
-> ... and files: ad56004080g300170h.evt ad56004080g300270l.evt ad56004080g300370m.evt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2808     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515       666           4849         0         0         0
 Writing events file
    666 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111        11            100         0         0         0
 Writing events file
    677 events written to the output file
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808       335           2473         0         0         0
 Writing events file
   1012 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8434      1012           7422         0         0         0
   in  7318.1     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad56004080g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Extracting ad56004080g300070_1.lc with binsize 361.56619267737
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.73E+04     1012     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1012      1012              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1012      1012              0         0         0         0
   in  7318.1     seconds
 Fits light curve has     1012 counts for 0.1383     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set binsize 361.56619267737
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad56004080g300070_1.lc
Wrote FITS light curve to file ad56004080g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Plotting ad56004080g300070_1.lc in ad56004080g300070_1_lc.ps
-> Standard Output From FTOOL lcurve:

 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad56004080g300070_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ GC REGION 2         Start Time (d) .... 11067 12:26:06.638
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 11067 18:50:38.638
 No. of Rows .......           20        Bin Time (s) ......    361.6
 Right Ascension ... 2.6556E+02          Internal time sys.. Converted to TJD
 Declination ....... -3.0129E+01         Experiment ........ ASCA     GIS3
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 11067.51813238430  (days)      12:26: 6:638  (h:m:s:ms)
 Expected Stop .... 11067.78516942134  (days)      18:50:38:638  (h:m:s:ms)
 
 Minimum Newbin Time    361.56619      (s)
 for Maximum Newbin No..               64
 
 Default Newbin Time is:   361.56619    (s) (to have 1 Intv. of      64 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     361.56619      (s)
 Maximum Newbin No.                64
 
 Default Newbins per Interval are:        64
 (giving       1 Interval of        64 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with        64 Newbins of       361.566     (s)
 
      64 analysis results per interval
 
  5% completed
 10% completed
 15% completed
 20% completed
 25% completed
 30% completed
 35% completed
 40% completed
 45% completed
 50% completed
 55% completed
 60% completed
 65% completed
 70% completed
 75% completed
 80% completed
 85% completed
 90% completed
 95% completed
100% completed
 
 Intv    1   Start 11067 13:35:24
     Ser.1     Avg 0.1380        Chisq  16.43       Var 0.3241E-03 Newbs.     20
               Min 0.1079          Max 0.1742    expVar 0.4274E-03  Bins     20
PLT> @lightcurve.pco
!PLT> dev ad56004080g300070_1_lc.ps/ps
!PLT> LA File ad56004080g300070_1.lc
!PLT> plot
!PLT> quit

-> Merging GTIs from the following files:

ad56004080g200170h.evt[2]
ad56004080g200270l.evt[2]
ad56004080g200370m.evt[2]

-> Making L1 light curve of ft980911_1122_1920G2HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:

ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  12811 output records from   12824  good input G2_L1    records.

-> Making L1 light curve of ft980911_1122_1920G2HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:

ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   6934 output records from   15129  good input G2_L1    records.

-> Merging GTIs from the following files:

ad56004080g300170h.evt[2]
ad56004080g300270l.evt[2]
ad56004080g300370m.evt[2]

-> Making L1 light curve of ft980911_1122_1920G3HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:

ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  12421 output records from   12434  good input G3_L1    records.

-> Making L1 light curve of ft980911_1122_1920G3HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:

ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   6846 output records from   14709  good input G3_L1    records.

Extracting source event files (9:29:43)

-> Extracting unbinned light curve ad56004080g200170.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5199     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5199       816           4383         0         0         0
 Writing events file
    816 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5199       816           4383         0         0         0
   in  4824.0     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad56004080g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad56004080g200170.ulc use_events=yes
Wrote events list to file ad56004080g200170.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080g200270.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02       91     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             91        18             73         0         0         0
 Writing events file
     18 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            91        18             73         0         0         0
   in  96.000     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200270l.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad56004080g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad56004080g200270.ulc use_events=yes
Wrote events list to file ad56004080g200270.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080g200370.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2506     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2506       393           2113         0         0         0
 Writing events file
    393 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2506       393           2113         0         0         0
   in  2400.1     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200370m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad56004080g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad56004080g200370.ulc use_events=yes
Wrote events list to file ad56004080g200370.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080g300170.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.48E+04     5515     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           5515       666           4849         0         0         0
 Writing events file
    666 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5515       666           4849         0         0         0
   in  4822.0     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad56004080g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad56004080g300170.ulc use_events=yes
Wrote events list to file ad56004080g300170.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080g300270.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.96E+02      111     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            111        11            100         0         0         0
 Writing events file
     11 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           111        11            100         0         0         0
   in  96.000     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300270l.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad56004080g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad56004080g300270.ulc use_events=yes
Wrote events list to file ad56004080g300270.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080g300370.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.24E+04     2808     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2808       335           2473         0         0         0
 Writing events file
    335 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2808       335           2473         0         0         0
   in  2400.1     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300370m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad56004080g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad56004080g300370.ulc use_events=yes
Wrote events list to file ad56004080g300370.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Extracting unbinned light curve ad56004080s000102.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.86E+02       31 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             31        31              0         0         0         0
 Writing events file
     31 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            31        31              0         0         0         0
   in  85.799     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad56004080s000102.ulc use_events=yes
Wrote events list to file ad56004080s000102.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Extracting unbinned light curve ad56004080s000112.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  12:50:00    0.86E+02       33 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             33        33              0         0         0         0
 Writing events file
     33 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            33        33              0         0         0         0
   in  85.799     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad56004080s000112.ulc use_events=yes
Wrote events list to file ad56004080s000112.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Extracting unbinned light curve ad56004080s000202.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1228 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1228      1228              0         0         0         0
 Writing events file
   1228 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1228      1228              0         0         0         0
   in  4839.7     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad56004080s000202.ulc use_events=yes
Wrote events list to file ad56004080s000202.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Extracting unbinned light curve ad56004080s000212.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1328 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000212h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1328      1328              0         0         0         0
 Writing events file
   1328 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1328      1328              0         0         0         0
   in  4839.7     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000212h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad56004080s000212.ulc use_events=yes
Wrote events list to file ad56004080s000212.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Extracting unbinned light curve ad56004080s000302.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.18E+04      459 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            459       459              0         0         0         0
 Writing events file
    459 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           459       459              0         0         0         0
   in  1834.2     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000302m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad56004080s000302.ulc use_events=yes
Wrote events list to file ad56004080s000302.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no

-> Extracting unbinned light curve ad56004080s000312.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.18E+04      490 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            490       490              0         0         0         0
 Writing events file
    490 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           490       490              0         0         0         0
   in  1834.2     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s000312m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad56004080s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad56004080s000312.ulc use_events=yes
Wrote events list to file ad56004080s000312.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Extracting unbinned light curve ad56004080s100102.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.48E+04     1047 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1047      1047              0         0         0         0
 Writing events file
   1047 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1047      1047              0         0         0         0
   in  4843.6     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad56004080s100102.ulc use_events=yes
Wrote events list to file ad56004080s100102.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Extracting unbinned light curve ad56004080s100112.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.48E+04     1100 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1100      1100              0         0         0         0
 Writing events file
   1100 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1100      1100              0         0         0         0
   in  4843.6     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad56004080s100112.ulc use_events=yes
Wrote events list to file ad56004080s100112.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Extracting unbinned light curve ad56004080s100202.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.17E+04      375 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            375       375              0         0         0         0
 Writing events file
    375 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           375       375              0         0         0         0
   in  1706.2     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad56004080s100202.ulc use_events=yes
Wrote events list to file ad56004080s100202.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

-> Extracting unbinned light curve ad56004080s100212.ulc
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.17E+04      390 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            390       390              0         0         0         0
 Writing events file
    390 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           390       390              0         0         0         0
   in  1706.2     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080s100212m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad56004080s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad56004080s100212.ulc use_events=yes
Wrote events list to file ad56004080s100212.ulc
Changing Data directory from:
    /data/data23/seq_proc/ad0_56004080.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

Extracting FRAME mode data (9:36:31)

-> Extracting FRAME mode data from ft980911_1122.1920
-> stdout output from tlmFrm

 *** tlmFrm Version 1.1 (1997-08-25) *** 
total number of superframes: 7077
frame data: 179670818.624318 ---> 179670962.623866 
     S0, C1, 2 ccd mode;  Output File = fr980911_1122.1920_s0c1m2a.fits
frame data: 179670982.623803 ---> 179671126.623352 
     S0, C2, 2 ccd mode;  Output File = fr980911_1122.1920_s0c2m2a.fits
frame data: 179671146.623289 ---> 179671290.622837 
     S0, C1, 2 ccd mode;  Output File = fr980911_1122.1920_s0c1m2b.fits
frame data: 179671310.622774 ---> 179671454.622323 
     S0, C2, 2 ccd mode;  Output File = fr980911_1122.1920_s0c2m2b.fits

Total of 4 sets of frame data are extracted.

-> Processing frame fr980911_1122.1920_s0c1m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl

Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980911_1122.1920_s0c1m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 298

-> Adding keywords to fr980911_1122.1920_s0c1m2a.fits
-> Processing frame fr980911_1122.1920_s0c1m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl

Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980911_1122.1920_s0c1m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 298

-> Adding keywords to fr980911_1122.1920_s0c1m2b.fits
-> Processing frame fr980911_1122.1920_s0c2m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl

Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980911_1122.1920_s0c2m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 333

-> Adding keywords to fr980911_1122.1920_s0c2m2a.fits
-> Processing frame fr980911_1122.1920_s0c2m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl

Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980911_1122.1920_s0c2m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 333

-> Adding keywords to fr980911_1122.1920_s0c2m2b.fits
-> Extracting corner pixel histograms
-> Extracting corner pixels from ad56004080s000101h.unf
-> Calculating corner pixel GTI from ft980911_1122_1920.mkf
-> Extracting corner pixels from ad56004080s000201h.unf
-> Extracting corner pixels from ad56004080s000301m.unf
-> Extracting corner pixels from ad56004080s000401l.unf
-> Extracting corner pixels from ad56004080s000501l.unf
-> Extracting corner pixels from ad56004080s000601m.unf
-> Extracting corner pixels from ad56004080s100101h.unf
-> Extracting corner pixels from ad56004080s100201m.unf
-> Extracting corner pixels from ad56004080s100301l.unf

Extracting GIS calibration source spectra (9:38:46)

-> Standard Output From STOOL group_event_files:

1 ad56004080g200170h.unf 28483
1 ad56004080g200270l.unf 28483
1 ad56004080g200370m.unf 28483

-> Fetching GIS2_CALSRC256.2
-> Extracting ad56004080g220170.cal from ad56004080g200170h.unf ad56004080g200270l.unf ad56004080g200370m.unf
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7859     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7859     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4819     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15805      1486          14319         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7859       734           7125         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4819       434           4385         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         28483      2654          25829         0         0         0
   in  18488.     seconds
 Spectrum         has     2654 counts for 0.1436     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18488.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.57970E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g220170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200270l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > read events ad56004080g200370m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad56004080g220170.cal group=yes
Wrote spectrum to ad56004080g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no

-> Deleting BLANK keyword from ad56004080g220170.cal
-> gis2v4_0.rmf already present in current directory
-> Plotting ad56004080g220170_cal.ps and finding peak
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:39:41 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad56004080g220170.cal;
 Net count rate (cts/s) for file   1  0.1436    +/-  2.7986E-03
   using response (RMF) file...       gis2v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =     1.7240132E+07 using    84 PHA bins.
 Reduced chi-squared =      226843.8     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =     1.7240132E+07 using    84 PHA bins.
 Reduced chi-squared =      223897.8     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =     1.7240132E+07 using    84 PHA bins.
 Reduced chi-squared =      221027.3     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      1106.181     using    84 PHA bins.
 Reduced chi-squared =      14.00229     for     79 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   251.427     -2         0.      3.5100E-03   6.078          0.
              6.3234E-02  9.5419E-03
   199.782     -3         0.      2.9929E-03   5.986          0.
              6.4371E-02  1.1624E-02
   170.468     -4         0.      2.6243E-03   6.037          0.
              6.4526E-02  1.3679E-02
   168.003     -5         0.      3.0752E-03   6.026          0.
              6.5161E-02  1.2584E-02
   167.597     -6         0.      2.8197E-03   6.015          0.
              6.5176E-02  1.2576E-02
 Maximum number of increasing lambda iterations exceeded
 without decreasing the fit statistic, probable minimum
 found to available numerical accuracy
   102.834     -3         0.      2.7258E-03   6.002      0.1768
              6.6013E-02  1.2997E-02
   88.6725     -4         0.      2.0270E-03   6.018      0.1810
              7.3335E-02  1.0384E-02
   87.5819     -5         0.      2.5380E-03   6.021      0.1789
              7.3868E-02  9.7655E-03
 Number of trials exceeded - last iteration delta =    1.091
   87.1520     -6         0.      2.2253E-03   6.022      0.1789
              7.3947E-02  9.6711E-03
   87.0265     -7         0.      2.4184E-03   6.022      0.1789
              7.3959E-02  9.6568E-03
   86.9739     -8         0.      2.2978E-03   6.022      0.1789
              7.3961E-02  9.6547E-03
   86.9551     -9         0.      2.3722E-03   6.022      0.1789
              7.3961E-02  9.6543E-03
   86.9477    -10         0.      2.3259E-03   6.022      0.1789
              7.3961E-02  9.6543E-03
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 1.75E-07 | -0.99  0.00 -0.01 -0.04 -0.13
 1.24E-06 |  0.13 -0.06 -0.02 -0.08 -0.99
 4.52E-06 | -0.02 -0.05 -0.07  0.99 -0.08
 8.59E-05 |  0.01  0.86 -0.52  0.01 -0.04
 2.91E-04 | -0.01  0.51  0.85  0.08 -0.06
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               2.3259E-03 +/-  0.4602E-03
    3    3    2   gaussian/b LineE    keV        6.022     +/-  0.1178E-01
    4    4    2   gaussian/b Sigma    keV       0.1789     +/-  0.1533E-01
    5    5    2   gaussian/b norm               7.3961E-02 +/-  0.2540E-02
    6    3    3   gaussian/b LineE    keV        6.630     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       0.1877     = par   4 *   1.049
    8    6    3   gaussian/b norm               9.6543E-03 +/-  0.1563E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      86.94769     using    84 PHA bins.
 Reduced chi-squared =      1.100604     for     79 degrees of freedom
 Null hypothesis probability = 0.253

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS2 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Calibration source ad56004080g220170.cal peaks at 6.022 +/- 0.01178 keV
-> Standard Output From STOOL group_event_files:

1 ad56004080g300170h.unf 27948
1 ad56004080g300270l.unf 27948
1 ad56004080g300370m.unf 27948

-> Fetching GIS3_CALSRC256.2
-> Extracting ad56004080g320170.cal from ad56004080g300170h.unf ad56004080g300270l.unf ad56004080g300370m.unf
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7784     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
      2 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7784     1024
      3 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4854     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15310      1215          14095         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7784       598           7186         0         0         0
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4854       364           4490         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         27948      2177          25771         0         0         0
   in  18490.     seconds
 Spectrum         has     2177 counts for 0.1177     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18490.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.83360E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad56004080g320170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA > read events ad56004080g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300270l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > read events ad56004080g300370m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad56004080g320170.cal group=yes
Wrote spectrum to ad56004080g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no

-> Deleting BLANK keyword from ad56004080g320170.cal
-> gis3v4_0.rmf already present in current directory
-> Plotting ad56004080g320170_cal.ps and finding peak
-> Standard Output From STOOL xspec:


               Xspec 11.00 09:40:45 14-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad56004080g320170.cal;
 Net count rate (cts/s) for file   1  0.1177    +/-  2.5431E-03
   using response (RMF) file...       gis3v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =     2.5465600E+07 using    84 PHA bins.
 Reduced chi-squared =      335073.7     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =     2.5465600E+07 using    84 PHA bins.
 Reduced chi-squared =      330722.1     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =     2.5465600E+07 using    84 PHA bins.
 Reduced chi-squared =      326482.1     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      1142.855     using    84 PHA bins.
 Reduced chi-squared =      14.46653     for     79 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   675.192     -3         0.      6.8557E-04   6.038      2.1805E-02
              8.6169E-02  1.4321E-02
   192.370     -4         0.      2.1165E-03   5.958      0.2310
              6.6450E-02  7.4715E-03
   119.663     -5         0.      1.2466E-03   5.895      0.1223
              6.2789E-02  1.2620E-02
   107.347     -6         0.      1.5851E-03   5.928      0.1408
              6.7025E-02  8.7758E-03
   105.909     -7         0.      1.4425E-03   5.923      0.1275
              6.6468E-02  9.0460E-03
   105.863     -8         0.      1.5443E-03   5.925      0.1278
              6.6572E-02  8.9277E-03
   105.838     -9         0.      1.4714E-03   5.925      0.1274
              6.6555E-02  8.9451E-03
   105.828    -10         0.      1.5250E-03   5.925      0.1274
              6.6556E-02  8.9429E-03
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 1.39E-07 | -0.99  0.00 -0.01 -0.03 -0.10
 9.91E-07 |  0.10 -0.05 -0.02 -0.06 -0.99
 4.00E-06 | -0.02 -0.05 -0.05  1.00 -0.06
 2.52E-04 |  0.00  0.33  0.94  0.06 -0.04
 7.37E-05 |  0.00 -0.94  0.34 -0.02  0.05
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               1.5250E-03 +/-  0.3941E-03
    3    3    2   gaussian/b LineE    keV        5.925     +/-  0.9662E-02
    4    4    2   gaussian/b Sigma    keV       0.1274     +/-  0.1520E-01
    5    5    2   gaussian/b norm               6.6556E-02 +/-  0.2195E-02
    6    3    3   gaussian/b LineE    keV        6.523     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       0.1337     = par   4 *   1.049
    8    6    3   gaussian/b norm               8.9429E-03 +/-  0.1233E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      105.8284     using    84 PHA bins.
 Reduced chi-squared =      1.339600     for     79 degrees of freedom
 Null hypothesis probability = 2.367E-02

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS3 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

-> Calibration source ad56004080g320170.cal peaks at 5.925 +/- 0.009662 keV

Extracting bright and dark Earth event files. (9:40:54)

-> Extracting bright and dark Earth events from ad56004080s000102h.unf
-> Extracting ad56004080s000102h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  12:50:00    0.19E+04     1126 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1126       186              0       940         0         0
 Writing events file
    186 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1126       186              0       940         0         0
   in  108.30     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s000102h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          186
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               9          94
cleaning chip # 2
 Hot pixels & counts                   :               7          63
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :          186
 Number of image cts rejected (N, %) :          15784.41
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0          111           75            0
 Image cts rejected:             0           94           63            0
 Image cts rej (%) :          0.00        84.68        84.00         0.00
 
    filtering data...
 
 Total counts      :             0          111           75            0
 Total cts rejected:             0           94           63            0
 Total cts rej (%) :          0.00        84.68        84.00         0.00
 
 Number of clean counts accepted  :           29
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000112h.unf
-> Extracting ad56004080s000112h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  12:50:00    0.19E+04     1179 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1179       195              0       984         0         0
 Writing events file
    195 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1179       195              0       984         0         0
   in  108.30     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s000112h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          195
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               9          97
cleaning chip # 2
 Hot pixels & counts                   :               7          64
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :          195
 Number of image cts rejected (N, %) :          16182.56
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0          116           79            0
 Image cts rejected:             0           97           64            0
 Image cts rej (%) :          0.00        83.62        81.01         0.00
 
    filtering data...
 
 Total counts      :             0          116           79            0
 Total cts rejected:             0           97           64            0
 Total cts rej (%) :          0.00        83.62        81.01         0.00
 
 Number of clean counts accepted  :           34
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000202h.unf
-> Extracting ad56004080s000202h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.96E+04    11187 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000202h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          11187      1346              0      9841         0         0
 Writing events file
   1346 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11187      1346              0      9841         0         0
   in  1389.5     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000202h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s000202h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000202h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1346
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8         917
 Flickering pixels iter, pixels & cnts :   1           1           5
cleaning chip # 2
 Hot pixels & counts                   :               6         317
 Flickering pixels iter, pixels & cnts :   1           1           3
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         1346
 Number of image cts rejected (N, %) :         124292.27
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0          960          386            0
 Image cts rejected:             0          922          320            0
 Image cts rej (%) :          0.00        96.04        82.90         0.00
 
    filtering data...
 
 Total counts      :             0          960          386            0
 Total cts rejected:             0          922          320            0
 Total cts rej (%) :          0.00        96.04        82.90         0.00
 
 Number of clean counts accepted  :          104
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000212h.unf
-> Extracting ad56004080s000212h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.96E+04    11389 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000212h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          11389      1373              0     10016         0         0
 Writing events file
   1373 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11389      1373              0     10016         0         0
   in  1389.5     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000212h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s000212h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000212h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1373
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8         917
 Flickering pixels iter, pixels & cnts :   1           1           5
cleaning chip # 2
 Hot pixels & counts                   :               6         317
 Flickering pixels iter, pixels & cnts :   1           1           3
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         1373
 Number of image cts rejected (N, %) :         124290.46
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0          974          399            0
 Image cts rejected:             0          922          320            0
 Image cts rej (%) :          0.00        94.66        80.20         0.00
 
    filtering data...
 
 Total counts      :             0          974          399            0
 Total cts rejected:             0          922          320            0
 Total cts rej (%) :          0.00        94.66        80.20         0.00
 
 Number of clean counts accepted  :          131
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000302m.unf
-> Extracting ad56004080s000302m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.33E+04     3794 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000302m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3794        76              0      3718         0         0
 Writing events file
     76 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3794        76              0      3718         0         0
   in  75.596     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000302m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s000302m.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000302m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :           76
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               6          51
cleaning chip # 2
 Hot pixels & counts                   :               3          13
cleaning chip # 3
 
 Number of pixels rejected           :            9
 Number of (internal) image counts   :           76
 Number of image cts rejected (N, %) :           6484.21
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            6            3            0
 
 Image counts      :             0           57           19            0
 Image cts rejected:             0           51           13            0
 Image cts rej (%) :          0.00        89.47        68.42         0.00
 
    filtering data...
 
 Total counts      :             0           57           19            0
 Total cts rejected:             0           51           13            0
 Total cts rej (%) :          0.00        89.47        68.42         0.00
 
 Number of clean counts accepted  :           12
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            9
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000312m.unf
-> Extracting ad56004080s000312m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.33E+04     3875 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000312m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3875        76              0      3799         0         0
 Writing events file
     76 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3875        76              0      3799         0         0
   in  75.596     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000312m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s000312m.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000312m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :           76
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               6          51
cleaning chip # 2
 Hot pixels & counts                   :               3          13
cleaning chip # 3
 
 Number of pixels rejected           :            9
 Number of (internal) image counts   :           76
 Number of image cts rejected (N, %) :           6484.21
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            6            3            0
 
 Image counts      :             0           57           19            0
 Image cts rejected:             0           51           13            0
 Image cts rej (%) :          0.00        89.47        68.42         0.00
 
    filtering data...
 
 Total counts      :             0           57           19            0
 Total cts rejected:             0           51           13            0
 Total cts rej (%) :          0.00        89.47        68.42         0.00
 
 Number of clean counts accepted  :           12
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            9
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000402l.unf
-> Extracting ad56004080s000402l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT      LOW         1998-09-11  15:45:56    0.33E+04     2682 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000402l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2682      2668              0        14         0         0
 Writing events file
   2668 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2682      2668              0        14         0         0
   in  3264.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000402l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s000402l.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000402l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2668
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8        1809
 Flickering pixels iter, pixels & cnts :   1           1           9
cleaning chip # 2
 Hot pixels & counts                   :               7         730
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         2668
 Number of image cts rejected (N, %) :         254895.50
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0         1872          796            0
 Image cts rejected:             0         1818          730            0
 Image cts rej (%) :          0.00        97.12        91.71         0.00
 
    filtering data...
 
 Total counts      :             0         1872          796            0
 Total cts rejected:             0         1818          730            0
 Total cts rej (%) :          0.00        97.12        91.71         0.00
 
 Number of clean counts accepted  :          120
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s000412l.unf
-> Extracting ad56004080s000412l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 GC REGION 2 BRIGHT2     LOW         1998-09-11  15:45:56    0.33E+04     2713 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s000412l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2713      2697              0        16         0         0
 Writing events file
   2697 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2713      2697              0        16         0         0
   in  3264.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s000412l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s000412l.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s000412l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2697
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               8        1809
 Flickering pixels iter, pixels & cnts :   1           1           9
cleaning chip # 2
 Hot pixels & counts                   :               7         733
cleaning chip # 3
 
 Number of pixels rejected           :           16
 Number of (internal) image counts   :         2697
 Number of image cts rejected (N, %) :         255194.59
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            9            7            0
 
 Image counts      :             0         1884          813            0
 Image cts rejected:             0         1818          733            0
 Image cts rej (%) :          0.00        96.50        90.16         0.00
 
    filtering data...
 
 Total counts      :             0         1884          813            0
 Total cts rejected:             0         1818          733            0
 Total cts rej (%) :          0.00        96.50        90.16         0.00
 
 Number of clean counts accepted  :          146
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           16
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100102h.unf
-> Extracting ad56004080s100102h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      HIGH        1998-09-11  11:45:08    0.12E+05    31391 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          31391      4131              0     27260         0         0
 Writing events file
   4131 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         31391      4131              0     27260         0         0
   in  1497.8     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s100102h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4131
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              16        2077
 Flickering pixels iter, pixels & cnts :   1           6          40
cleaning chip # 2
 Hot pixels & counts                   :              13        1894
 Flickering pixels iter, pixels & cnts :   1           1           3
cleaning chip # 3
 
 Number of pixels rejected           :           36
 Number of (internal) image counts   :         4131
 Number of image cts rejected (N, %) :         401497.17
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           22           14            0
 
 Image counts      :             0         2171         1960            0
 Image cts rejected:             0         2117         1897            0
 Image cts rej (%) :          0.00        97.51        96.79         0.00
 
    filtering data...
 
 Total counts      :             0         2171         1960            0
 Total cts rejected:             0         2117         1897            0
 Total cts rej (%) :          0.00        97.51        96.79         0.00
 
 Number of clean counts accepted  :          117
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           36
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100112h.unf
-> Extracting ad56004080s100112h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     HIGH        1998-09-11  11:45:08    0.12E+05    31727 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          31727      4157              0     27570         0         0
 Writing events file
   4157 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         31727      4157              0     27570         0         0
   in  1497.8     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s100112h.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4157
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              16        2081
 Flickering pixels iter, pixels & cnts :   1           6          40
cleaning chip # 2
 Hot pixels & counts                   :              13        1898
 Flickering pixels iter, pixels & cnts :   1           1           3
cleaning chip # 3
 
 Number of pixels rejected           :           36
 Number of (internal) image counts   :         4157
 Number of image cts rejected (N, %) :         402296.75
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           22           14            0
 
 Image counts      :             0         2185         1972            0
 Image cts rejected:             0         2121         1901            0
 Image cts rej (%) :          0.00        97.07        96.40         0.00
 
    filtering data...
 
 Total counts      :             0         2185         1972            0
 Total cts rejected:             0         2121         1901            0
 Total cts rej (%) :          0.00        97.07        96.40         0.00
 
 Number of clean counts accepted  :          135
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           36
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100202m.unf
-> Extracting ad56004080s100202m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      MEDIUM      1998-09-11  11:44:52    0.35E+04     9561 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100202m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           9561       197              0      9364         0         0
 Writing events file
    197 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9561       197              0      9364         0         0
   in  75.596     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s100202m.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100202m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          197
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              12          87
cleaning chip # 2
 Hot pixels & counts                   :              10          94
cleaning chip # 3
 
 Number of pixels rejected           :           22
 Number of (internal) image counts   :          197
 Number of image cts rejected (N, %) :          18191.88
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           12           10            0
 
 Image counts      :             0           93          104            0
 Image cts rejected:             0           87           94            0
 Image cts rej (%) :          0.00        93.55        90.38         0.00
 
    filtering data...
 
 Total counts      :             0           93          104            0
 Total cts rejected:             0           87           94            0
 Total cts rej (%) :          0.00        93.55        90.38         0.00
 
 Number of clean counts accepted  :           16
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           22
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100212m.unf
-> Extracting ad56004080s100212m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     MEDIUM      1998-09-11  11:44:52    0.35E+04     9614 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100212m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           9614       199              0      9415         0         0
 Writing events file
    199 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9614       199              0      9415         0         0
   in  75.596     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s100212m.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100212m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          199
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              12          87
cleaning chip # 2
 Hot pixels & counts                   :              10          94
cleaning chip # 3
 
 Number of pixels rejected           :           22
 Number of (internal) image counts   :          199
 Number of image cts rejected (N, %) :          18190.95
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           12           10            0
 
 Image counts      :             0           94          105            0
 Image cts rejected:             0           87           94            0
 Image cts rej (%) :          0.00        92.55        89.52         0.00
 
    filtering data...
 
 Total counts      :             0           94          105            0
 Total cts rejected:             0           87           94            0
 Total cts rej (%) :          0.00        92.55        89.52         0.00
 
 Number of clean counts accepted  :           18
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           22
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100302l.unf
-> Extracting ad56004080s100302l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT      LOW         1998-09-11  15:45:56    0.56E+04     6355 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100302l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           6355      5358              0       997         0         0
 Writing events file
   5358 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6355      5358              0       997         0         0
   in  3390.6     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no

-> Cleaning hot pixels from ad56004080s100302l.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100302l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         5358
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              11        2851
 Flickering pixels iter, pixels & cnts :   1           4          62
cleaning chip # 2
 Hot pixels & counts                   :              11        2343
 Flickering pixels iter, pixels & cnts :   1           2          16
cleaning chip # 3
 
 Number of pixels rejected           :           28
 Number of (internal) image counts   :         5358
 Number of image cts rejected (N, %) :         527298.39
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           15           13            0
 
 Image counts      :             0         2950         2408            0
 Image cts rejected:             0         2913         2359            0
 Image cts rej (%) :          0.00        98.75        97.97         0.00
 
    filtering data...
 
 Total counts      :             0         2950         2408            0
 Total cts rejected:             0         2913         2359            0
 Total cts rej (%) :          0.00        98.75        97.97         0.00
 
 Number of clean counts accepted  :           86
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           28
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080s100312l.unf
-> Extracting ad56004080s100312l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 GC REGION 2 BRIGHT2     LOW         1998-09-11  15:45:56    0.56E+04     6423 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080s100312l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           6423      5368              0      1055         0         0
 Writing events file
   5368 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6423      5368              0      1055         0         0
   in  3390.6     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080s100312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no

-> Cleaning hot pixels from ad56004080s100312l.unf
-> Standard Output From FTOOL cleansis:

CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad56004080s100312l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         5368
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              11        2853
 Flickering pixels iter, pixels & cnts :   1           4          62
cleaning chip # 2
 Hot pixels & counts                   :              11        2345
 Flickering pixels iter, pixels & cnts :   1           2          16
cleaning chip # 3
 
 Number of pixels rejected           :           28
 Number of (internal) image counts   :         5368
 Number of image cts rejected (N, %) :         527698.29
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           15           13            0
 
 Image counts      :             0         2956         2412            0
 Image cts rejected:             0         2915         2361            0
 Image cts rej (%) :          0.00        98.61        97.89         0.00
 
    filtering data...
 
 Total counts      :             0         2956         2412            0
 Total cts rejected:             0         2915         2361            0
 Total cts rej (%) :          0.00        98.61        97.89         0.00
 
 Number of clean counts accepted  :           92
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           28
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...

-> Extracting bright and dark Earth events from ad56004080g200170h.unf
-> Extracting ad56004080g200170h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15805      1246              0     14559         0         0
 Writing events file
   1246 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15805      1246              0     14559         0         0
   in  2184.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting ad56004080g200170h.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15805     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15805      1625              0     14180         0         0
 Writing events file
   1625 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15805      1625              0     14180         0         0
   in  832.02     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting bright and dark Earth events from ad56004080g200270l.unf
-> Extracting ad56004080g200270l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7859      1806              0      6053         0         0
 Writing events file
   1806 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7859      1806              0      6053         0         0
   in  3232.2     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting ad56004080g200270l.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7859      5515              0      2344         0         0
 Writing events file
   5515 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7859      5515              0      2344         0         0
   in  1791.8     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting bright and dark Earth events from ad56004080g200370m.unf
-> Extracting ad56004080g200370m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4819     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4819        74              0      4745         0         0
 Writing events file
     74 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4819        74              0      4745         0         0
   in  95.846     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting ad56004080g200370m.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4819     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4819       340              0      4479         0         0
 Writing events file
    340 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4819       340              0      4479         0         0
   in  96.000     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g200370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no

-> Extracting bright and dark Earth events from ad56004080g300170h.unf
-> Extracting ad56004080g300170h.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15310      1202              0     14108         0         0
 Writing events file
   1202 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15310      1202              0     14108         0         0
   in  2188.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

-> Extracting ad56004080g300170h.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          HIGH        1998-09-11  11:52:06    0.10E+05    15310     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          15310      1455              0     13855         0         0
 Writing events file
   1455 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15310      1455              0     13855         0         0
   in  832.02     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

-> Extracting bright and dark Earth events from ad56004080g300270l.unf
-> Extracting ad56004080g300270l.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7784     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7784      1687              0      6097         0         0
 Writing events file
   1687 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7784      1687              0      6097         0         0
   in  3232.2     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

-> Extracting ad56004080g300270l.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          LOW         1998-09-11  15:46:06    0.52E+04     7784     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7784      5527              0      2257         0         0
 Writing events file
   5527 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7784      5527              0      2257         0         0
   in  1791.8     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300270l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

-> Extracting bright and dark Earth events from ad56004080g300370m.unf
-> Extracting ad56004080g300370m.drk
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4854     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4854        60              0      4794         0         0
 Writing events file
     60 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4854        60              0      4794         0         0
   in  95.846     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

-> Extracting ad56004080g300370m.brt
-> Standard Output From FTOOL xselect:

 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 GC REGION 2 PH          MEDIUM      1998-09-11  16:55:58    0.28E+04     4854     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data23/seq_proc/ad0_56004080.003/ad56004080g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4854       360              0      4494         0         0
 Writing events file
    360 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4854       360              0      4494         0         0
   in  96.000     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data23/seq_proc/ad0_56004080.003/
Setting mkf directory to /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA > read events ad56004080g300370m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data23/seq_proc/ad0_56004080.003/
HK Directory is: /data/data23/seq_proc/ad0_56004080.003/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

Determining information about this observation (9:56:48)

-> Calculating ISAS time for sis
-> Calculating ISAS time for gis
-> Recording dates of PI calibration files
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory

Generating event file information page (9:58:15)

-> Summing time and events for s0 event files
-> Standard Output From STOOL get_uniq_keys:

ad56004080s000102h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad56004080s000202h.unf|S0_ARENA|0|S0 Area discrimination enable/disable

-> listing ad56004080s000102h.unf
-> listing ad56004080s000202h.unf
-> listing ad56004080s000302m.unf
-> listing ad56004080s000402l.unf
-> Standard Output From STOOL get_uniq_keys:

ad56004080s000112h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad56004080s000212h.unf|S0_ARENA|0|S0 Area discrimination enable/disable

-> listing ad56004080s000112h.unf
-> listing ad56004080s000212h.unf
-> listing ad56004080s000312m.unf
-> listing ad56004080s000412l.unf
-> Standard Output From STOOL get_uniq_keys:

ad56004080s000101h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad56004080s000201h.unf|S0_ARENA|0|S0 Area discrimination enable/disable

-> listing ad56004080s000101h.unf
-> listing ad56004080s000201h.unf
-> Standard Output From STOOL get_uniq_keys:

ad56004080s000301m.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad56004080s000601m.unf|S0_ARENA|1|S0 Area discrimination enable/disable

-> listing ad56004080s000301m.unf
-> listing ad56004080s000601m.unf
-> Standard Output From STOOL get_uniq_keys:

ad56004080s000401l.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad56004080s000501l.unf|S0_ARENA|1|S0 Area discrimination enable/disable

-> listing ad56004080s000401l.unf
-> listing ad56004080s000501l.unf
-> Summing time and events for s1 event files
-> listing ad56004080s100102h.unf
-> listing ad56004080s100202m.unf
-> listing ad56004080s100302l.unf
-> listing ad56004080s100112h.unf
-> listing ad56004080s100212m.unf
-> listing ad56004080s100312l.unf
-> listing ad56004080s100101h.unf
-> listing ad56004080s100201m.unf
-> listing ad56004080s100301l.unf
-> Summing time and events for g2 event files
-> listing ad56004080g200170h.unf
-> listing ad56004080g200370m.unf
-> listing ad56004080g200270l.unf
-> Summing time and events for g3 event files
-> listing ad56004080g300170h.unf
-> listing ad56004080g300370m.unf
-> listing ad56004080g300270l.unf

Creating HTML header page (10:6:5)

Creating HTML source list (10:6:28)

Doing final wrapup of all files (10:7:12)

-> Copying job.par to ad56004080_003_job.par
-> Copying ad0.par to ad56004080_003_process.par
-> Creating ad56004080_tape.cat
-> Creating ad56004080_trend.cat
-> Creating ad56004080_003_file_info.html
-> Calculating site-independant checksums
-> Site independant checksum: 20657
-> Updating FITS checksum keywords
-> Running fverify on all FITS files