The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 212923429.511100 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-10-01 09:23:45.51109 Modified Julian Day = 51452.391498971061083-> leapsec.fits already present in current directory
Offset of 212962333.483100 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-10-01 20:12:09.48310 Modified Julian Day = 51452.841776424771524-> Observation begins 212923429.5111 1999-10-01 09:23:45
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 212923432.511000 212962323.880300
Data file start and stop ascatime : 212923432.511000 212962323.880300
Aspecting run start and stop ascatime : 212923432.511079 212962323.880215
Time interval averaged over (seconds) : 38891.369136
Total pointing and manuver time (sec) : 24037.474609 14853.984375
Mean boresight Euler angles : 268.294858 119.339961 185.235837
RA DEC SUN ANGLE
Mean solar position (deg) : 186.43 -2.78
Mean aberration (arcsec) : -3.50 -2.05
Mean sat X-axis (deg) : 257.701808 60.237494 83.28
Mean sat Y-axis (deg) : 175.723910 -4.562695 10.83
Mean sat Z-axis (deg) : 268.294858 -29.339962 81.55
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 268.020996 -29.494514 95.100983 0.718803
Minimum 267.951965 -29.500626 95.093437 0.092575
Maximum 268.036713 -29.481720 95.121635 3.624234
Sigma (RMS) 0.002222 0.000710 0.005228 0.668389
Number of ASPECT records processed = 27949
Aspecting to RA/DEC : 268.02099609 -29.49451447
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 212950361.92060 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 268.021 DEC: -29.495
START TIME: SC 212923432.5111 = UT 1999-10-01 09:23:52
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000098 3.353 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
2245.992432 2.632 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2787.490723 1.629 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2878.490234 0.628 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
4455.985352 0.718 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
7951.973145 0.846 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
10151.965820 0.570 D080C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 2
13655.954102 0.496 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
15815.947266 0.379 D880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 3
19361.935547 0.289 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
21527.927734 0.394 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
25067.916016 0.366 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
28103.906250 0.453 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
30771.896484 0.461 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
32935.890625 0.496 D880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 3
36477.878906 0.520 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
38635.871094 0.532 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
38891.371094 0.498 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
Attitude Records: 27949
Attitude Steps: 18
Maneuver ACM time: 14854.0 sec
Pointed ACM time: 24037.5 sec
-> Calculating aspect point99 99 count=4 sum1=1072.92 sum2=477.368 sum3=740.963 99 100 count=4 sum1=1072.91 sum2=477.379 sum3=740.955 100 98 count=1 sum1=268.24 sum2=119.333 sum3=185.245 100 99 count=31 sum1=8315.3 sum2=3699.45 sum3=5742.52 100 100 count=1 sum1=268.231 sum2=119.343 sum3=185.234 101 98 count=2736 sum1=733922 sum2=326480 sum3=506844 102 98 count=87 sum1=23338.3 sum2=10381.7 sum3=16116.4 103 98 count=85 sum1=22802.6 sum2=10143.2 sum3=15745.7 104 98 count=39 sum1=10462.6 sum2=4653.99 sum3=7224.44 104 99 count=59 sum1=15828.4 sum2=7040.72 sum3=10929.2 105 99 count=130 sum1=34877.2 sum2=15513.7 sum3=24081.2 106 99 count=5089 sum1=1.36538e+06 sum2=607327 sum3=942650 106 100 count=12 sum1=3219.61 sum2=1432.12 sum3=2222.77 107 99 count=8746 sum1=2.34658e+06 sum2=1.04376e+06 sum3=1.62006e+06 107 100 count=10925 sum1=2.93124e+06 sum2=1.30382e+06 sum3=2.02368e+06 0 out of 27949 points outside bin structure-> Euler angles: 268.304, 119.342, 185.234
61.9997 second gap between superframes 2010 and 2011 Dropping SF 2368 with corrupted frame indicator Dropping SF 2369 with inconsistent datamode 0/31 Dropping SF 2371 with inconsistent datamode 0/31 Dropping SF 2372 with inconsistent datamode 0/31 15.9999 second gap between superframes 3470 and 3471 87.9997 second gap between superframes 4401 and 4402 Warning: GIS2 bit assignment changed between 212949833.42233 and 212949835.42233 Warning: GIS3 bit assignment changed between 212949839.42231 and 212949841.42231 Warning: GIS2 bit assignment changed between 212949849.42228 and 212949851.42227 Warning: GIS3 bit assignment changed between 212949855.42226 and 212949857.42225 SIS0 coordinate error time=212949957.29689 x=0 y=4 pha[0]=1914 chip=0 SIS0 peak error time=212949957.29689 x=0 y=4 ph0=1914 ph3=2624 SIS1 peak error time=212950001.29674 x=143 y=278 ph0=166 ph4=1588 ph5=2473 Dropping SF 4764 with invalid bit rate 7 Dropping SF 4765 with inconsistent datamode 0/31 Dropping SF 4766 with inconsistent datamode 0/31 Dropping SF 4767 with inconsistent datamode 0/31 Dropping SF 4768 with inconsistent datamode 0/31 Dropping SF 6598 with inconsistent datamode 0/1 Dropping SF 6642 with inconsistent datamode 0/31 Dropping SF 6648 with inconsistent datamode 0/31 Dropping SF 6653 with inconsistent SIS mode 1/3 Dropping SF 6654 with inconsistent datamode 22/0 Dropping SF 6658 with corrupted frame indicator Dropping SF 6671 with inconsistent datamode 0/31 Dropping SF 6699 with corrupted frame indicator Dropping SF 6713 with inconsistent datamode 0/31 Dropping SF 6725 with corrupted frame indicator SIS1 peak error time=212961089.25935 x=221 y=302 ph0=184 ph4=1529 SIS1 peak error time=212961089.25935 x=69 y=309 ph0=184 ph6=1599 Dropping SF 6758 with inconsistent datamode 0/31 Dropping SF 6763 with synch code word 2 = 140 not 32 Dropping SF 6764 with corrupted frame indicator Dropping SF 7025 with inconsistent datamode 0/31 7002 of 7025 super frames processed-> Removing the following files with NEVENTS=0
ft991001_0923_2012G200170M.fits[0] ft991001_0923_2012G200270L.fits[0] ft991001_0923_2012G200370M.fits[0] ft991001_0923_2012G200470M.fits[0] ft991001_0923_2012G200570M.fits[0] ft991001_0923_2012G201270L.fits[0] ft991001_0923_2012G201370M.fits[0] ft991001_0923_2012G201470M.fits[0] ft991001_0923_2012G201570M.fits[0] ft991001_0923_2012G202370L.fits[0] ft991001_0923_2012G202470M.fits[0] ft991001_0923_2012G202570M.fits[0] ft991001_0923_2012G202670M.fits[0] ft991001_0923_2012G202770M.fits[0] ft991001_0923_2012G203370M.fits[0] ft991001_0923_2012G203470L.fits[0] ft991001_0923_2012G203570H.fits[0] ft991001_0923_2012G203670H.fits[0] ft991001_0923_2012G203770H.fits[0] ft991001_0923_2012G203870H.fits[0] ft991001_0923_2012G203970H.fits[0] ft991001_0923_2012G204170H.fits[0] ft991001_0923_2012G204470M.fits[0] ft991001_0923_2012G204570L.fits[0] ft991001_0923_2012G204670L.fits[0] ft991001_0923_2012G204770H.fits[0] ft991001_0923_2012G204970H.fits[0] ft991001_0923_2012G205470H.fits[0] ft991001_0923_2012G205570H.fits[0] ft991001_0923_2012G205670H.fits[0] ft991001_0923_2012G205770H.fits[0] ft991001_0923_2012G206470H.fits[0] ft991001_0923_2012G206570H.fits[0] ft991001_0923_2012G206670L.fits[0] ft991001_0923_2012G206770L.fits[0] ft991001_0923_2012G206870H.fits[0] ft991001_0923_2012G206970H.fits[0] ft991001_0923_2012G207070H.fits[0] ft991001_0923_2012G207170H.fits[0] ft991001_0923_2012G207270H.fits[0] ft991001_0923_2012G207370H.fits[0] ft991001_0923_2012G208370M.fits[0] ft991001_0923_2012G208470L.fits[0] ft991001_0923_2012G208570L.fits[0] ft991001_0923_2012G208670H.fits[0] ft991001_0923_2012G208770H.fits[0] ft991001_0923_2012G300170M.fits[0] ft991001_0923_2012G300270L.fits[0] ft991001_0923_2012G300370M.fits[0] ft991001_0923_2012G300470M.fits[0] ft991001_0923_2012G300570M.fits[0] ft991001_0923_2012G300670M.fits[0] ft991001_0923_2012G301270L.fits[0] ft991001_0923_2012G301370M.fits[0] ft991001_0923_2012G301470M.fits[0] ft991001_0923_2012G301570M.fits[0] ft991001_0923_2012G301670M.fits[0] ft991001_0923_2012G302370L.fits[0] ft991001_0923_2012G302470M.fits[0] ft991001_0923_2012G302570M.fits[0] ft991001_0923_2012G302670M.fits[0] ft991001_0923_2012G302770M.fits[0] ft991001_0923_2012G303370M.fits[0] ft991001_0923_2012G303470L.fits[0] ft991001_0923_2012G303570H.fits[0] ft991001_0923_2012G303670H.fits[0] ft991001_0923_2012G303770H.fits[0] ft991001_0923_2012G303870H.fits[0] ft991001_0923_2012G303970H.fits[0] ft991001_0923_2012G304470M.fits[0] ft991001_0923_2012G304570L.fits[0] ft991001_0923_2012G304670L.fits[0] ft991001_0923_2012G304770H.fits[0] ft991001_0923_2012G304870H.fits[0] ft991001_0923_2012G305470H.fits[0] ft991001_0923_2012G305570H.fits[0] ft991001_0923_2012G305670H.fits[0] ft991001_0923_2012G305770H.fits[0] ft991001_0923_2012G306470H.fits[0] ft991001_0923_2012G306570L.fits[0] ft991001_0923_2012G306670L.fits[0] ft991001_0923_2012G306770H.fits[0] ft991001_0923_2012G306870H.fits[0] ft991001_0923_2012G306970H.fits[0] ft991001_0923_2012G307070H.fits[0] ft991001_0923_2012G307170H.fits[0] ft991001_0923_2012G307370H.fits[0] ft991001_0923_2012G308270M.fits[0] ft991001_0923_2012G308370L.fits[0] ft991001_0923_2012G308470L.fits[0] ft991001_0923_2012G308570H.fits[0] ft991001_0923_2012G308670H.fits[0] ft991001_0923_2012G308770H.fits[0] ft991001_0923_2012S000101M.fits[0] ft991001_0923_2012S000701L.fits[0] ft991001_0923_2012S100101M.fits[0] ft991001_0923_2012S100701L.fits[0]-> Checking for empty GTI extensions
ft991001_0923_2012S000201L.fits[2] ft991001_0923_2012S000301L.fits[2] ft991001_0923_2012S000401M.fits[2] ft991001_0923_2012S000501H.fits[2] ft991001_0923_2012S000601L.fits[2] ft991001_0923_2012S000801L.fits[2] ft991001_0923_2012S000901M.fits[2] ft991001_0923_2012S001001H.fits[2] ft991001_0923_2012S001101M.fits[2] ft991001_0923_2012S001201L.fits[2] ft991001_0923_2012S001301L.fits[2] ft991001_0923_2012S001401L.fits[2] ft991001_0923_2012S001501M.fits[2] ft991001_0923_2012S001601H.fits[2] ft991001_0923_2012S001701M.fits[2] ft991001_0923_2012S001801L.fits[2] ft991001_0923_2012S001901L.fits[2] ft991001_0923_2012S002001L.fits[2] ft991001_0923_2012S002101H.fits[2] ft991001_0923_2012S002201M.fits[2] ft991001_0923_2012S002301L.fits[2] ft991001_0923_2012S002401L.fits[2] ft991001_0923_2012S002501L.fits[2] ft991001_0923_2012S002601H.fits[2] ft991001_0923_2012S002701L.fits[2] ft991001_0923_2012S002801H.fits[2] ft991001_0923_2012S002901H.fits[2] ft991001_0923_2012S003001L.fits[2] ft991001_0923_2012S003101L.fits[2] ft991001_0923_2012S003201H.fits[2] ft991001_0923_2012S003301M.fits[2] ft991001_0923_2012S003401L.fits[2] ft991001_0923_2012S003501M.fits[2] ft991001_0923_2012S003601L.fits[2] ft991001_0923_2012S003701L.fits[2] ft991001_0923_2012S003801H.fits[2]-> Merging GTIs from the following files:
ft991001_0923_2012S100201L.fits[2] ft991001_0923_2012S100301L.fits[2] ft991001_0923_2012S100401M.fits[2] ft991001_0923_2012S100501H.fits[2] ft991001_0923_2012S100601L.fits[2] ft991001_0923_2012S100801L.fits[2] ft991001_0923_2012S100901M.fits[2] ft991001_0923_2012S101001H.fits[2] ft991001_0923_2012S101101M.fits[2] ft991001_0923_2012S101201L.fits[2] ft991001_0923_2012S101301L.fits[2] ft991001_0923_2012S101401L.fits[2] ft991001_0923_2012S101501M.fits[2] ft991001_0923_2012S101601H.fits[2] ft991001_0923_2012S101701M.fits[2] ft991001_0923_2012S101801L.fits[2] ft991001_0923_2012S101901L.fits[2] ft991001_0923_2012S102001L.fits[2] ft991001_0923_2012S102101H.fits[2] ft991001_0923_2012S102201M.fits[2] ft991001_0923_2012S102301L.fits[2] ft991001_0923_2012S102401L.fits[2] ft991001_0923_2012S102501L.fits[2] ft991001_0923_2012S102601H.fits[2] ft991001_0923_2012S102701L.fits[2] ft991001_0923_2012S102801H.fits[2] ft991001_0923_2012S102901H.fits[2] ft991001_0923_2012S103001L.fits[2] ft991001_0923_2012S103101L.fits[2] ft991001_0923_2012S103201H.fits[2] ft991001_0923_2012S103301M.fits[2] ft991001_0923_2012S103401L.fits[2] ft991001_0923_2012S103501M.fits[2] ft991001_0923_2012S103601L.fits[2] ft991001_0923_2012S103701L.fits[2] ft991001_0923_2012S103801H.fits[2]-> Merging GTIs from the following files:
ft991001_0923_2012G200670M.fits[2] ft991001_0923_2012G200770M.fits[2] ft991001_0923_2012G200870M.fits[2] ft991001_0923_2012G200970H.fits[2] ft991001_0923_2012G201070L.fits[2] ft991001_0923_2012G201170L.fits[2] ft991001_0923_2012G201670M.fits[2] ft991001_0923_2012G201770M.fits[2] ft991001_0923_2012G201870M.fits[2] ft991001_0923_2012G201970H.fits[2] ft991001_0923_2012G202070M.fits[2] ft991001_0923_2012G202170L.fits[2] ft991001_0923_2012G202270L.fits[2] ft991001_0923_2012G202870M.fits[2] ft991001_0923_2012G202970M.fits[2] ft991001_0923_2012G203070H.fits[2] ft991001_0923_2012G203170H.fits[2] ft991001_0923_2012G203270M.fits[2] ft991001_0923_2012G204070H.fits[2] ft991001_0923_2012G204270H.fits[2] ft991001_0923_2012G204370M.fits[2] ft991001_0923_2012G204870H.fits[2] ft991001_0923_2012G205070H.fits[2] ft991001_0923_2012G205170H.fits[2] ft991001_0923_2012G205270H.fits[2] ft991001_0923_2012G205370H.fits[2] ft991001_0923_2012G205870H.fits[2] ft991001_0923_2012G205970H.fits[2] ft991001_0923_2012G206070H.fits[2] ft991001_0923_2012G206170H.fits[2] ft991001_0923_2012G206270L.fits[2] ft991001_0923_2012G206370H.fits[2] ft991001_0923_2012G207470H.fits[2] ft991001_0923_2012G207570H.fits[2] ft991001_0923_2012G207670M.fits[2] ft991001_0923_2012G207770L.fits[2] ft991001_0923_2012G207870L.fits[2] ft991001_0923_2012G207970M.fits[2] ft991001_0923_2012G208070M.fits[2] ft991001_0923_2012G208170M.fits[2] ft991001_0923_2012G208270M.fits[2] ft991001_0923_2012G208870H.fits[2] ft991001_0923_2012G208970H.fits[2] ft991001_0923_2012G209070H.fits[2]-> Merging GTIs from the following files:
ft991001_0923_2012G300770M.fits[2] ft991001_0923_2012G300870M.fits[2] ft991001_0923_2012G300970H.fits[2] ft991001_0923_2012G301070L.fits[2] ft991001_0923_2012G301170L.fits[2] ft991001_0923_2012G301770M.fits[2] ft991001_0923_2012G301870M.fits[2] ft991001_0923_2012G301970H.fits[2] ft991001_0923_2012G302070M.fits[2] ft991001_0923_2012G302170L.fits[2] ft991001_0923_2012G302270L.fits[2] ft991001_0923_2012G302870M.fits[2] ft991001_0923_2012G302970M.fits[2] ft991001_0923_2012G303070H.fits[2] ft991001_0923_2012G303170H.fits[2] ft991001_0923_2012G303270M.fits[2] ft991001_0923_2012G304070H.fits[2] ft991001_0923_2012G304170H.fits[2] ft991001_0923_2012G304270H.fits[2] ft991001_0923_2012G304370M.fits[2] ft991001_0923_2012G304970H.fits[2] ft991001_0923_2012G305070H.fits[2] ft991001_0923_2012G305170H.fits[2] ft991001_0923_2012G305270H.fits[2] ft991001_0923_2012G305370H.fits[2] ft991001_0923_2012G305870H.fits[2] ft991001_0923_2012G305970H.fits[2] ft991001_0923_2012G306070H.fits[2] ft991001_0923_2012G306170L.fits[2] ft991001_0923_2012G306270H.fits[2] ft991001_0923_2012G306370H.fits[2] ft991001_0923_2012G307270H.fits[2] ft991001_0923_2012G307470H.fits[2] ft991001_0923_2012G307570M.fits[2] ft991001_0923_2012G307670L.fits[2] ft991001_0923_2012G307770L.fits[2] ft991001_0923_2012G307870M.fits[2] ft991001_0923_2012G307970M.fits[2] ft991001_0923_2012G308070M.fits[2] ft991001_0923_2012G308170M.fits[2] ft991001_0923_2012G308870H.fits[2] ft991001_0923_2012G308970H.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 3 photon cnt = 8 GISSORTSPLIT:LO:g200570h.prelist merge count = 12 photon cnt = 19190 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 148 GISSORTSPLIT:LO:g200270l.prelist merge count = 4 photon cnt = 5191 GISSORTSPLIT:LO:g200370l.prelist merge count = 1 photon cnt = 67 GISSORTSPLIT:LO:g200170m.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g200270m.prelist merge count = 3 photon cnt = 98 GISSORTSPLIT:LO:g200370m.prelist merge count = 8 photon cnt = 11720 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 78 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 59 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 70 GISSORTSPLIT:LO:Total filenames split = 44 GISSORTSPLIT:LO:Total split file cnt = 16 GISSORTSPLIT:LO:End program-> Creating ad57003040g200170h.unf
---- cmerge: version 1.6 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G200970H.fits 2 -- ft991001_0923_2012G201970H.fits 3 -- ft991001_0923_2012G203070H.fits 4 -- ft991001_0923_2012G203170H.fits 5 -- ft991001_0923_2012G204270H.fits 6 -- ft991001_0923_2012G205170H.fits 7 -- ft991001_0923_2012G205270H.fits 8 -- ft991001_0923_2012G206070H.fits 9 -- ft991001_0923_2012G206170H.fits 10 -- ft991001_0923_2012G206370H.fits 11 -- ft991001_0923_2012G207570H.fits 12 -- ft991001_0923_2012G209070H.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G200970H.fits 2 -- ft991001_0923_2012G201970H.fits 3 -- ft991001_0923_2012G203070H.fits 4 -- ft991001_0923_2012G203170H.fits 5 -- ft991001_0923_2012G204270H.fits 6 -- ft991001_0923_2012G205170H.fits 7 -- ft991001_0923_2012G205270H.fits 8 -- ft991001_0923_2012G206070H.fits 9 -- ft991001_0923_2012G206170H.fits 10 -- ft991001_0923_2012G206370H.fits 11 -- ft991001_0923_2012G207570H.fits 12 -- ft991001_0923_2012G209070H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040g200270m.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G200870M.fits 2 -- ft991001_0923_2012G201870M.fits 3 -- ft991001_0923_2012G202070M.fits 4 -- ft991001_0923_2012G202970M.fits 5 -- ft991001_0923_2012G203270M.fits 6 -- ft991001_0923_2012G204370M.fits 7 -- ft991001_0923_2012G207670M.fits 8 -- ft991001_0923_2012G208270M.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G200870M.fits 2 -- ft991001_0923_2012G201870M.fits 3 -- ft991001_0923_2012G202070M.fits 4 -- ft991001_0923_2012G202970M.fits 5 -- ft991001_0923_2012G203270M.fits 6 -- ft991001_0923_2012G204370M.fits 7 -- ft991001_0923_2012G207670M.fits 8 -- ft991001_0923_2012G208270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040g200370l.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G201070L.fits 2 -- ft991001_0923_2012G202170L.fits 3 -- ft991001_0923_2012G206270L.fits 4 -- ft991001_0923_2012G207870L.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G201070L.fits 2 -- ft991001_0923_2012G202170L.fits 3 -- ft991001_0923_2012G206270L.fits 4 -- ft991001_0923_2012G207870L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000148 events
ft991001_0923_2012G201170L.fits ft991001_0923_2012G202270L.fits-> Ignoring the following files containing 000000098 events
ft991001_0923_2012G200770M.fits ft991001_0923_2012G201770M.fits ft991001_0923_2012G202870M.fits-> Ignoring the following files containing 000000078 events
ft991001_0923_2012G208170M.fits-> Ignoring the following files containing 000000070 events
ft991001_0923_2012G208070M.fits-> Ignoring the following files containing 000000067 events
ft991001_0923_2012G207770L.fits-> Ignoring the following files containing 000000059 events
ft991001_0923_2012G207970M.fits-> Ignoring the following files containing 000000008 events
ft991001_0923_2012G205070H.fits ft991001_0923_2012G207470H.fits ft991001_0923_2012G208970H.fits-> Ignoring the following files containing 000000003 events
ft991001_0923_2012G204070H.fits ft991001_0923_2012G208870H.fits-> Ignoring the following files containing 000000002 events
ft991001_0923_2012G205870H.fits-> Ignoring the following files containing 000000002 events
ft991001_0923_2012G200670M.fits ft991001_0923_2012G201670M.fits-> Ignoring the following files containing 000000001 events
ft991001_0923_2012G205970H.fits-> Ignoring the following files containing 000000001 events
ft991001_0923_2012G204870H.fits-> Ignoring the following files containing 000000001 events
ft991001_0923_2012G205370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 6 GISSORTSPLIT:LO:g300370h.prelist merge count = 3 photon cnt = 5 GISSORTSPLIT:LO:g300470h.prelist merge count = 12 photon cnt = 18968 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300170l.prelist merge count = 2 photon cnt = 140 GISSORTSPLIT:LO:g300270l.prelist merge count = 4 photon cnt = 4800 GISSORTSPLIT:LO:g300370l.prelist merge count = 1 photon cnt = 54 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 96 GISSORTSPLIT:LO:g300270m.prelist merge count = 8 photon cnt = 11516 GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 68 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 61 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 78 GISSORTSPLIT:LO:Total filenames split = 42 GISSORTSPLIT:LO:Total split file cnt = 14 GISSORTSPLIT:LO:End program-> Creating ad57003040g300170h.unf
---- cmerge: version 1.6 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G300970H.fits 2 -- ft991001_0923_2012G301970H.fits 3 -- ft991001_0923_2012G303070H.fits 4 -- ft991001_0923_2012G303170H.fits 5 -- ft991001_0923_2012G304270H.fits 6 -- ft991001_0923_2012G305170H.fits 7 -- ft991001_0923_2012G305270H.fits 8 -- ft991001_0923_2012G305970H.fits 9 -- ft991001_0923_2012G306070H.fits 10 -- ft991001_0923_2012G306270H.fits 11 -- ft991001_0923_2012G307470H.fits 12 -- ft991001_0923_2012G308970H.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G300970H.fits 2 -- ft991001_0923_2012G301970H.fits 3 -- ft991001_0923_2012G303070H.fits 4 -- ft991001_0923_2012G303170H.fits 5 -- ft991001_0923_2012G304270H.fits 6 -- ft991001_0923_2012G305170H.fits 7 -- ft991001_0923_2012G305270H.fits 8 -- ft991001_0923_2012G305970H.fits 9 -- ft991001_0923_2012G306070H.fits 10 -- ft991001_0923_2012G306270H.fits 11 -- ft991001_0923_2012G307470H.fits 12 -- ft991001_0923_2012G308970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040g300270m.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G300870M.fits 2 -- ft991001_0923_2012G301870M.fits 3 -- ft991001_0923_2012G302070M.fits 4 -- ft991001_0923_2012G302970M.fits 5 -- ft991001_0923_2012G303270M.fits 6 -- ft991001_0923_2012G304370M.fits 7 -- ft991001_0923_2012G307570M.fits 8 -- ft991001_0923_2012G308170M.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G300870M.fits 2 -- ft991001_0923_2012G301870M.fits 3 -- ft991001_0923_2012G302070M.fits 4 -- ft991001_0923_2012G302970M.fits 5 -- ft991001_0923_2012G303270M.fits 6 -- ft991001_0923_2012G304370M.fits 7 -- ft991001_0923_2012G307570M.fits 8 -- ft991001_0923_2012G308170M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040g300370l.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012G301070L.fits 2 -- ft991001_0923_2012G302170L.fits 3 -- ft991001_0923_2012G306170L.fits 4 -- ft991001_0923_2012G307770L.fits Merging binary extension #: 2 1 -- ft991001_0923_2012G301070L.fits 2 -- ft991001_0923_2012G302170L.fits 3 -- ft991001_0923_2012G306170L.fits 4 -- ft991001_0923_2012G307770L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000140 events
ft991001_0923_2012G301170L.fits ft991001_0923_2012G302270L.fits-> Ignoring the following files containing 000000096 events
ft991001_0923_2012G300770M.fits ft991001_0923_2012G301770M.fits ft991001_0923_2012G302870M.fits-> Ignoring the following files containing 000000078 events
ft991001_0923_2012G307970M.fits-> Ignoring the following files containing 000000068 events
ft991001_0923_2012G308070M.fits-> Ignoring the following files containing 000000061 events
ft991001_0923_2012G307870M.fits-> Ignoring the following files containing 000000054 events
ft991001_0923_2012G307670L.fits-> Ignoring the following files containing 000000006 events
ft991001_0923_2012G304070H.fits ft991001_0923_2012G304970H.fits ft991001_0923_2012G307270H.fits-> Ignoring the following files containing 000000005 events
ft991001_0923_2012G304170H.fits ft991001_0923_2012G305070H.fits ft991001_0923_2012G308870H.fits-> Ignoring the following files containing 000000003 events
ft991001_0923_2012G305870H.fits-> Ignoring the following files containing 000000002 events
ft991001_0923_2012G306370H.fits-> Ignoring the following files containing 000000001 events
ft991001_0923_2012G305370H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 8 photon cnt = 233288 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 168 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 13 photon cnt = 13435 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 6 photon cnt = 216 SIS0SORTSPLIT:LO:s000501m.prelist merge count = 8 photon cnt = 36930 SIS0SORTSPLIT:LO:Total filenames split = 36 SIS0SORTSPLIT:LO:Total split file cnt = 5 SIS0SORTSPLIT:LO:End program-> Creating ad57003040s000101h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S000501H.fits 2 -- ft991001_0923_2012S001001H.fits 3 -- ft991001_0923_2012S001601H.fits 4 -- ft991001_0923_2012S002101H.fits 5 -- ft991001_0923_2012S002601H.fits 6 -- ft991001_0923_2012S002801H.fits 7 -- ft991001_0923_2012S003201H.fits 8 -- ft991001_0923_2012S003801H.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S000501H.fits 2 -- ft991001_0923_2012S001001H.fits 3 -- ft991001_0923_2012S001601H.fits 4 -- ft991001_0923_2012S002101H.fits 5 -- ft991001_0923_2012S002601H.fits 6 -- ft991001_0923_2012S002801H.fits 7 -- ft991001_0923_2012S003201H.fits 8 -- ft991001_0923_2012S003801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040s000201m.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S000401M.fits 2 -- ft991001_0923_2012S000901M.fits 3 -- ft991001_0923_2012S001101M.fits 4 -- ft991001_0923_2012S001501M.fits 5 -- ft991001_0923_2012S001701M.fits 6 -- ft991001_0923_2012S002201M.fits 7 -- ft991001_0923_2012S003301M.fits 8 -- ft991001_0923_2012S003501M.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S000401M.fits 2 -- ft991001_0923_2012S000901M.fits 3 -- ft991001_0923_2012S001101M.fits 4 -- ft991001_0923_2012S001501M.fits 5 -- ft991001_0923_2012S001701M.fits 6 -- ft991001_0923_2012S002201M.fits 7 -- ft991001_0923_2012S003301M.fits 8 -- ft991001_0923_2012S003501M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040s000301l.unf
---- cmerge: version 1.6 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S000301L.fits 2 -- ft991001_0923_2012S000601L.fits 3 -- ft991001_0923_2012S000801L.fits 4 -- ft991001_0923_2012S001201L.fits 5 -- ft991001_0923_2012S001401L.fits 6 -- ft991001_0923_2012S001801L.fits 7 -- ft991001_0923_2012S002001L.fits 8 -- ft991001_0923_2012S002301L.fits 9 -- ft991001_0923_2012S002501L.fits 10 -- ft991001_0923_2012S002701L.fits 11 -- ft991001_0923_2012S003001L.fits 12 -- ft991001_0923_2012S003401L.fits 13 -- ft991001_0923_2012S003601L.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S000301L.fits 2 -- ft991001_0923_2012S000601L.fits 3 -- ft991001_0923_2012S000801L.fits 4 -- ft991001_0923_2012S001201L.fits 5 -- ft991001_0923_2012S001401L.fits 6 -- ft991001_0923_2012S001801L.fits 7 -- ft991001_0923_2012S002001L.fits 8 -- ft991001_0923_2012S002301L.fits 9 -- ft991001_0923_2012S002501L.fits 10 -- ft991001_0923_2012S002701L.fits 11 -- ft991001_0923_2012S003001L.fits 12 -- ft991001_0923_2012S003401L.fits 13 -- ft991001_0923_2012S003601L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000216 events
ft991001_0923_2012S000201L.fits ft991001_0923_2012S001301L.fits ft991001_0923_2012S001901L.fits ft991001_0923_2012S002401L.fits ft991001_0923_2012S003101L.fits ft991001_0923_2012S003701L.fits-> Ignoring the following files containing 000000168 events
ft991001_0923_2012S002901H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 8 photon cnt = 310487 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 257 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 13 photon cnt = 13145 SIS1SORTSPLIT:LO:s100401l.prelist merge count = 6 photon cnt = 209 SIS1SORTSPLIT:LO:s100501m.prelist merge count = 8 photon cnt = 28862 SIS1SORTSPLIT:LO:Total filenames split = 36 SIS1SORTSPLIT:LO:Total split file cnt = 5 SIS1SORTSPLIT:LO:End program-> Creating ad57003040s100101h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S100501H.fits 2 -- ft991001_0923_2012S101001H.fits 3 -- ft991001_0923_2012S101601H.fits 4 -- ft991001_0923_2012S102101H.fits 5 -- ft991001_0923_2012S102601H.fits 6 -- ft991001_0923_2012S102801H.fits 7 -- ft991001_0923_2012S103201H.fits 8 -- ft991001_0923_2012S103801H.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S100501H.fits 2 -- ft991001_0923_2012S101001H.fits 3 -- ft991001_0923_2012S101601H.fits 4 -- ft991001_0923_2012S102101H.fits 5 -- ft991001_0923_2012S102601H.fits 6 -- ft991001_0923_2012S102801H.fits 7 -- ft991001_0923_2012S103201H.fits 8 -- ft991001_0923_2012S103801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040s100201m.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S100401M.fits 2 -- ft991001_0923_2012S100901M.fits 3 -- ft991001_0923_2012S101101M.fits 4 -- ft991001_0923_2012S101501M.fits 5 -- ft991001_0923_2012S101701M.fits 6 -- ft991001_0923_2012S102201M.fits 7 -- ft991001_0923_2012S103301M.fits 8 -- ft991001_0923_2012S103501M.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S100401M.fits 2 -- ft991001_0923_2012S100901M.fits 3 -- ft991001_0923_2012S101101M.fits 4 -- ft991001_0923_2012S101501M.fits 5 -- ft991001_0923_2012S101701M.fits 6 -- ft991001_0923_2012S102201M.fits 7 -- ft991001_0923_2012S103301M.fits 8 -- ft991001_0923_2012S103501M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad57003040s100301l.unf
---- cmerge: version 1.6 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft991001_0923_2012S100301L.fits 2 -- ft991001_0923_2012S100601L.fits 3 -- ft991001_0923_2012S100801L.fits 4 -- ft991001_0923_2012S101201L.fits 5 -- ft991001_0923_2012S101401L.fits 6 -- ft991001_0923_2012S101801L.fits 7 -- ft991001_0923_2012S102001L.fits 8 -- ft991001_0923_2012S102301L.fits 9 -- ft991001_0923_2012S102501L.fits 10 -- ft991001_0923_2012S102701L.fits 11 -- ft991001_0923_2012S103001L.fits 12 -- ft991001_0923_2012S103401L.fits 13 -- ft991001_0923_2012S103601L.fits Merging binary extension #: 2 1 -- ft991001_0923_2012S100301L.fits 2 -- ft991001_0923_2012S100601L.fits 3 -- ft991001_0923_2012S100801L.fits 4 -- ft991001_0923_2012S101201L.fits 5 -- ft991001_0923_2012S101401L.fits 6 -- ft991001_0923_2012S101801L.fits 7 -- ft991001_0923_2012S102001L.fits 8 -- ft991001_0923_2012S102301L.fits 9 -- ft991001_0923_2012S102501L.fits 10 -- ft991001_0923_2012S102701L.fits 11 -- ft991001_0923_2012S103001L.fits 12 -- ft991001_0923_2012S103401L.fits 13 -- ft991001_0923_2012S103601L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000257 events
ft991001_0923_2012S102901H.fits-> Ignoring the following files containing 000000209 events
ft991001_0923_2012S100201L.fits ft991001_0923_2012S101301L.fits ft991001_0923_2012S101901L.fits ft991001_0923_2012S102401L.fits ft991001_0923_2012S103101L.fits ft991001_0923_2012S103701L.fits-> Tar-ing together the leftover raw files
a ft991001_0923_2012G200670M.fits 31K a ft991001_0923_2012G200770M.fits 31K a ft991001_0923_2012G201170L.fits 31K a ft991001_0923_2012G201670M.fits 31K a ft991001_0923_2012G201770M.fits 31K a ft991001_0923_2012G202270L.fits 34K a ft991001_0923_2012G202870M.fits 31K a ft991001_0923_2012G204070H.fits 31K a ft991001_0923_2012G204870H.fits 31K a ft991001_0923_2012G205070H.fits 31K a ft991001_0923_2012G205370H.fits 31K a ft991001_0923_2012G205870H.fits 31K a ft991001_0923_2012G205970H.fits 31K a ft991001_0923_2012G207470H.fits 31K a ft991001_0923_2012G207770L.fits 31K a ft991001_0923_2012G207970M.fits 31K a ft991001_0923_2012G208070M.fits 31K a ft991001_0923_2012G208170M.fits 31K a ft991001_0923_2012G208870H.fits 31K a ft991001_0923_2012G208970H.fits 31K a ft991001_0923_2012G300770M.fits 31K a ft991001_0923_2012G301170L.fits 31K a ft991001_0923_2012G301770M.fits 31K a ft991001_0923_2012G302270L.fits 34K a ft991001_0923_2012G302870M.fits 31K a ft991001_0923_2012G304070H.fits 31K a ft991001_0923_2012G304170H.fits 31K a ft991001_0923_2012G304970H.fits 31K a ft991001_0923_2012G305070H.fits 31K a ft991001_0923_2012G305370H.fits 31K a ft991001_0923_2012G305870H.fits 31K a ft991001_0923_2012G306370H.fits 31K a ft991001_0923_2012G307270H.fits 31K a ft991001_0923_2012G307670L.fits 31K a ft991001_0923_2012G307870M.fits 31K a ft991001_0923_2012G307970M.fits 31K a ft991001_0923_2012G308070M.fits 31K a ft991001_0923_2012G308870H.fits 31K a ft991001_0923_2012S000201L.fits 29K a ft991001_0923_2012S001301L.fits 29K a ft991001_0923_2012S001901L.fits 31K a ft991001_0923_2012S002401L.fits 29K a ft991001_0923_2012S002901H.fits 34K a ft991001_0923_2012S003101L.fits 29K a ft991001_0923_2012S003701L.fits 29K a ft991001_0923_2012S100201L.fits 29K a ft991001_0923_2012S101301L.fits 29K a ft991001_0923_2012S101901L.fits 31K a ft991001_0923_2012S102401L.fits 29K a ft991001_0923_2012S102901H.fits 37K a ft991001_0923_2012S103101L.fits 29K a ft991001_0923_2012S103701L.fits 29K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft991001_0923.2012' is successfully opened Data Start Time is 212923427.51 (19991001 092343) Time Margin 2.0 sec included Warning: ascatime of the latest parameters for GIS2 in the calibration file is 208224004.00 Warning: ascatime of the latest parameters for GIS3 in the calibration file is 208224004.00 'ft991001_0923.2012' EOF detected, sf=7025 Data End Time is 212962333.38 (19991001 201209) Warning: ascatime of the latest parameters for GIS2 in the calibration file is 197078404.00 Warning: ascatime of the latest parameters for GIS3 in the calibration file is 197078404.00 Gain History is written in ft991001_0923_2012.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft991001_0923_2012.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft991001_0923_2012.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft991001_0923_2012CMHK.fits
The sum of the selected column is 24422.000 The mean of the selected column is 96.529644 The standard deviation of the selected column is 1.2709009 The minimum of selected column is 93.000000 The maximum of selected column is 98.000000 The number of points used in calculation is 253-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24422.000 The mean of the selected column is 96.529644 The standard deviation of the selected column is 1.2709009 The minimum of selected column is 93.000000 The maximum of selected column is 98.000000 The number of points used in calculation is 253
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040g200270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040g300170h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040g300270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000101h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000102h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000112h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000201m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000202m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000212m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000301l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000302l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s000312l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100101h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100102h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100112h.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100201m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100202m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100212m.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad57003040s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod) WARNING: Event end time not covered by gain history file WARNING: extrapolating gain/CTI trend-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 212950361.92060 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:
S0-HK file: ft991001_0923_2012S0HK.fits
S1-HK file: ft991001_0923_2012S1HK.fits
G2-HK file: ft991001_0923_2012G2HK.fits
G3-HK file: ft991001_0923_2012G3HK.fits
Date and time are: 1999-10-01 09:22:29 mjd=51452.390619
Orbit file name is ./frf.orbit.240
Epoch of Orbital Elements: 1999-09-27 17:00:00
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa991001_0923.2012
output FITS File: ft991001_0923_2012.mkf
mkfilter2: Warning, faQparam error: time= 2.129233655111e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 2.129233975111e+08 outside range of attitude file
Euler angles undefined for this bin
Total 1219 Data bins were processed.
-> Checking if column TIME in ft991001_0923_2012.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 5987.7387 The mean of the selected column is 25.588627 The standard deviation of the selected column is 6.4490422 The minimum of selected column is 14.593799 The maximum of selected column is 50.343922 The number of points used in calculation is 234-> Calculating statistics for S0_PIXL1
The sum of the selected column is 4390.0959 The mean of the selected column is 18.841613 The standard deviation of the selected column is 5.5453848 The minimum of selected column is 9.5625324 The maximum of selected column is 38.218880 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>6.2 && S0_PIXL0<44.9 )&& (S0_PIXL1>2.2 && S0_PIXL1<35.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad57003040s000112h.unf into ad57003040s000112h.evt
The sum of the selected column is 5987.7387 The mean of the selected column is 25.588627 The standard deviation of the selected column is 6.4490422 The minimum of selected column is 14.593799 The maximum of selected column is 50.343922 The number of points used in calculation is 234-> Calculating statistics for S0_PIXL1
The sum of the selected column is 4390.0959 The mean of the selected column is 18.841613 The standard deviation of the selected column is 5.5453848 The minimum of selected column is 9.5625324 The maximum of selected column is 38.218880 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>6.2 && S0_PIXL0<44.9 )&& (S0_PIXL1>2.2 && S0_PIXL1<35.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad57003040s000201m.unf because of mode
The sum of the selected column is 1954.0066 The mean of the selected column is 27.138980 The standard deviation of the selected column is 6.4658746 The minimum of selected column is 16.781305 The maximum of selected column is 45.843906 The number of points used in calculation is 72-> Calculating statistics for S0_PIXL1
The sum of the selected column is 1611.8179 The mean of the selected column is 22.079698 The standard deviation of the selected column is 7.0281046 The minimum of selected column is 10.406284 The maximum of selected column is 43.500149 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>7.7 && S0_PIXL0<46.5 )&& (S0_PIXL1>0.9 && S0_PIXL1<43.1 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad57003040s000212m.unf into ad57003040s000212m.evt
The sum of the selected column is 1954.0066 The mean of the selected column is 27.138980 The standard deviation of the selected column is 6.4658746 The minimum of selected column is 16.781305 The maximum of selected column is 45.843906 The number of points used in calculation is 72-> Calculating statistics for S0_PIXL1
The sum of the selected column is 1611.8179 The mean of the selected column is 22.079698 The standard deviation of the selected column is 7.0281046 The minimum of selected column is 10.406284 The maximum of selected column is 43.500149 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>7.7 && S0_PIXL0<46.5 )&& (S0_PIXL1>0.9 && S0_PIXL1<43.1 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad57003040s000301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&&(S0_PIXL1>0) )&&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad57003040s000302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&&(S0_PIXL1>0) )&&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad57003040s000312l.evt since it contains 0 events
The sum of the selected column is 7922.3806 The mean of the selected column is 33.712258 The standard deviation of the selected column is 9.3393377 The minimum of selected column is 16.093803 The maximum of selected column is 73.843994 The number of points used in calculation is 235-> Calculating statistics for S1_PIXL1
The sum of the selected column is 7749.0071 The mean of the selected column is 33.257541 The standard deviation of the selected column is 9.7051476 The minimum of selected column is 15.718802 The maximum of selected column is 75.125252 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>5.6 && S1_PIXL0<61.7 )&& (S1_PIXL1>4.1 && S1_PIXL1<62.3 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad57003040s100112h.unf into ad57003040s100112h.evt
The sum of the selected column is 7922.3806 The mean of the selected column is 33.712258 The standard deviation of the selected column is 9.3393377 The minimum of selected column is 16.093803 The maximum of selected column is 73.843994 The number of points used in calculation is 235-> Calculating statistics for S1_PIXL1
The sum of the selected column is 7749.0071 The mean of the selected column is 33.257541 The standard deviation of the selected column is 9.7051476 The minimum of selected column is 15.718802 The maximum of selected column is 75.125252 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>5.6 && S1_PIXL0<61.7 )&& (S1_PIXL1>4.1 && S1_PIXL1<62.3 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad57003040s100201m.unf because of mode
The sum of the selected column is 2604.1129 The mean of the selected column is 34.721506 The standard deviation of the selected column is 11.958454 The minimum of selected column is 16.875057 The maximum of selected column is 71.218994 The number of points used in calculation is 75-> Calculating statistics for S1_PIXL1
The sum of the selected column is 2510.2585 The mean of the selected column is 34.387102 The standard deviation of the selected column is 10.560986 The minimum of selected column is 19.000065 The maximum of selected column is 79.719017 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0 && S1_PIXL0<70.5 )&& (S1_PIXL1>2.7 && S1_PIXL1<66 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad57003040s100212m.unf into ad57003040s100212m.evt
The sum of the selected column is 2604.1129 The mean of the selected column is 34.721506 The standard deviation of the selected column is 11.958454 The minimum of selected column is 16.875057 The maximum of selected column is 71.218994 The number of points used in calculation is 75-> Calculating statistics for S1_PIXL1
The sum of the selected column is 2510.2585 The mean of the selected column is 34.387102 The standard deviation of the selected column is 10.560986 The minimum of selected column is 19.000065 The maximum of selected column is 79.719017 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0 && S1_PIXL0<70.5 )&& (S1_PIXL1>2.7 && S1_PIXL1<66 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad57003040s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&&(S1_PIXL1>0) )&&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad57003040s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&&(S1_PIXL1>0) )&&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad57003040s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad57003040g200270m.unf into ad57003040g200270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad57003040g200370l.unf into ad57003040g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Deleting ad57003040g200370l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad57003040g300270m.unf into ad57003040g300270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad57003040g300370l.unf into ad57003040g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Deleting ad57003040g300370l.evt since it contains 0 events
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad57003040g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0978
Mean RA/DEC/ROLL : 268.0432 -29.4763 95.0978
Pnt RA/DEC/ROLL : 267.9661 -29.5044 95.0978
Image rebin factor : 1
Attitude Records : 27950
GTI intervals : 15
Total GTI (secs) : 7794.055
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1308.50 1308.50
20 Percent Complete: Total/live time: 1759.99 1759.99
30 Percent Complete: Total/live time: 3569.54 3569.54
40 Percent Complete: Total/live time: 3569.54 3569.54
50 Percent Complete: Total/live time: 4527.54 4527.54
60 Percent Complete: Total/live time: 4980.03 4980.03
70 Percent Complete: Total/live time: 6727.93 6727.93
80 Percent Complete: Total/live time: 6727.93 6727.93
90 Percent Complete: Total/live time: 7794.05 7794.05
100 Percent Complete: Total/live time: 7794.05 7794.05
Number of attitude steps used: 27
Number of attitude steps avail: 17508
Mean RA/DEC pixel offset: -9.8666 -3.3136
writing expo file: ad57003040g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040g200170h.evt
ASCAEXPO_V0.9b
reading data file: ad57003040g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0980
Mean RA/DEC/ROLL : 268.0405 -29.4755 95.0980
Pnt RA/DEC/ROLL : 267.9663 -29.5045 95.0980
Image rebin factor : 1
Attitude Records : 27950
GTI intervals : 7
Total GTI (secs) : 2528.124
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 415.00 415.00
20 Percent Complete: Total/live time: 1504.03 1504.03
30 Percent Complete: Total/live time: 1504.03 1504.03
40 Percent Complete: Total/live time: 1568.09 1568.09
50 Percent Complete: Total/live time: 1568.09 1568.09
60 Percent Complete: Total/live time: 1664.02 1664.02
70 Percent Complete: Total/live time: 1952.12 1952.12
80 Percent Complete: Total/live time: 2259.01 2259.01
90 Percent Complete: Total/live time: 2528.12 2528.12
100 Percent Complete: Total/live time: 2528.12 2528.12
Number of attitude steps used: 13
Number of attitude steps avail: 6831
Mean RA/DEC pixel offset: -10.0051 -2.5904
writing expo file: ad57003040g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040g200270m.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad57003040g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0980
Mean RA/DEC/ROLL : 268.0430 -29.5011 95.0980
Pnt RA/DEC/ROLL : 267.9664 -29.4795 95.0980
Image rebin factor : 1
Attitude Records : 27950
GTI intervals : 15
Total GTI (secs) : 7794.055
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1308.50 1308.50
20 Percent Complete: Total/live time: 1759.99 1759.99
30 Percent Complete: Total/live time: 3569.54 3569.54
40 Percent Complete: Total/live time: 3569.54 3569.54
50 Percent Complete: Total/live time: 4527.54 4527.54
60 Percent Complete: Total/live time: 4980.03 4980.03
70 Percent Complete: Total/live time: 6727.93 6727.93
80 Percent Complete: Total/live time: 6727.93 6727.93
90 Percent Complete: Total/live time: 7794.05 7794.05
100 Percent Complete: Total/live time: 7794.05 7794.05
Number of attitude steps used: 27
Number of attitude steps avail: 17508
Mean RA/DEC pixel offset: 1.7647 -2.1581
writing expo file: ad57003040g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040g300170h.evt
ASCAEXPO_V0.9b
reading data file: ad57003040g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0982
Mean RA/DEC/ROLL : 268.0402 -29.5003 95.0982
Pnt RA/DEC/ROLL : 267.9666 -29.4796 95.0982
Image rebin factor : 1
Attitude Records : 27950
GTI intervals : 7
Total GTI (secs) : 2528.124
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 415.00 415.00
20 Percent Complete: Total/live time: 1504.03 1504.03
30 Percent Complete: Total/live time: 1504.03 1504.03
40 Percent Complete: Total/live time: 1568.09 1568.09
50 Percent Complete: Total/live time: 1568.09 1568.09
60 Percent Complete: Total/live time: 1664.02 1664.02
70 Percent Complete: Total/live time: 1952.12 1952.12
80 Percent Complete: Total/live time: 2259.01 2259.01
90 Percent Complete: Total/live time: 2528.12 2528.12
100 Percent Complete: Total/live time: 2528.12 2528.12
Number of attitude steps used: 13
Number of attitude steps avail: 6831
Mean RA/DEC pixel offset: 1.1444 -1.4828
writing expo file: ad57003040g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040g300270m.evt
ASCAEXPO_V0.9b
reading data file: ad57003040s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0893
Mean RA/DEC/ROLL : 268.0587 -29.4869 95.0893
Pnt RA/DEC/ROLL : 267.9488 -29.4932 95.0893
Image rebin factor : 4
Attitude Records : 27950
Hot Pixels : 385
GTI intervals : 21
Total GTI (secs) : 7521.790
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1012.49 1012.49
20 Percent Complete: Total/live time: 1760.01 1760.01
30 Percent Complete: Total/live time: 3542.45 3542.45
40 Percent Complete: Total/live time: 3542.45 3542.45
50 Percent Complete: Total/live time: 4952.93 4952.93
60 Percent Complete: Total/live time: 4952.93 4952.93
70 Percent Complete: Total/live time: 6188.19 6188.19
80 Percent Complete: Total/live time: 6188.19 6188.19
90 Percent Complete: Total/live time: 7341.67 7341.67
100 Percent Complete: Total/live time: 7521.79 7521.79
Number of attitude steps used: 31
Number of attitude steps avail: 17718
Mean RA/DEC pixel offset: -38.0435 -92.3259
writing expo file: ad57003040s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040s000102h.evt
ASCAEXPO_V0.9b
reading data file: ad57003040s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0895
Mean RA/DEC/ROLL : 268.0576 -29.4867 95.0895
Pnt RA/DEC/ROLL : 267.9485 -29.4933 95.0895
Image rebin factor : 4
Attitude Records : 27950
Hot Pixels : 17
GTI intervals : 11
Total GTI (secs) : 2251.679
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 501.85 501.85
20 Percent Complete: Total/live time: 501.85 501.85
30 Percent Complete: Total/live time: 1579.68 1579.68
40 Percent Complete: Total/live time: 1579.68 1579.68
50 Percent Complete: Total/live time: 1598.57 1598.57
60 Percent Complete: Total/live time: 1598.57 1598.57
70 Percent Complete: Total/live time: 1739.68 1739.68
80 Percent Complete: Total/live time: 2251.68 2251.68
100 Percent Complete: Total/live time: 2251.68 2251.68
Number of attitude steps used: 9
Number of attitude steps avail: 4301
Mean RA/DEC pixel offset: -39.7665 -77.6741
writing expo file: ad57003040s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040s000202m.evt
ASCAEXPO_V0.9b
reading data file: ad57003040s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0983
Mean RA/DEC/ROLL : 268.0407 -29.4875 95.0983
Pnt RA/DEC/ROLL : 267.9671 -29.4928 95.0983
Image rebin factor : 4
Attitude Records : 27950
Hot Pixels : 424
GTI intervals : 19
Total GTI (secs) : 7586.186
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1012.49 1012.49
20 Percent Complete: Total/live time: 1760.01 1760.01
30 Percent Complete: Total/live time: 3524.62 3524.62
40 Percent Complete: Total/live time: 3524.62 3524.62
50 Percent Complete: Total/live time: 4967.10 4967.10
60 Percent Complete: Total/live time: 4967.10 4967.10
70 Percent Complete: Total/live time: 6340.58 6340.58
80 Percent Complete: Total/live time: 6340.58 6340.58
90 Percent Complete: Total/live time: 7398.06 7398.06
100 Percent Complete: Total/live time: 7586.19 7586.19
Number of attitude steps used: 31
Number of attitude steps avail: 17861
Mean RA/DEC pixel offset: -42.3062 -22.8547
writing expo file: ad57003040s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040s100102h.evt
ASCAEXPO_V0.9b
reading data file: ad57003040s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa991001_0923.2012
making an exposure map...
Aspect RA/DEC/ROLL : 268.0300 -29.4965 95.0985
Mean RA/DEC/ROLL : 268.0395 -29.4871 95.0985
Pnt RA/DEC/ROLL : 267.9668 -29.4929 95.0985
Image rebin factor : 4
Attitude Records : 27950
Hot Pixels : 8
GTI intervals : 11
Total GTI (secs) : 2283.679
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 437.85 437.85
20 Percent Complete: Total/live time: 1451.68 1451.68
30 Percent Complete: Total/live time: 1451.68 1451.68
40 Percent Complete: Total/live time: 1470.57 1470.57
50 Percent Complete: Total/live time: 1470.57 1470.57
60 Percent Complete: Total/live time: 1675.68 1675.68
70 Percent Complete: Total/live time: 1675.68 1675.68
80 Percent Complete: Total/live time: 2283.68 2283.68
100 Percent Complete: Total/live time: 2283.68 2283.68
Number of attitude steps used: 9
Number of attitude steps avail: 4387
Mean RA/DEC pixel offset: -43.7443 -13.7826
writing expo file: ad57003040s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad57003040s100202m.evtad57003040s000102h.expo ad57003040s000202m.expo ad57003040s100102h.expo ad57003040s100202m.expo-> Summing the following images to produce ad57003040sis32002_all.totsky
ad57003040s000102h.img ad57003040s000202m.img ad57003040s100102h.img ad57003040s100202m.img-> Summing the following images to produce ad57003040sis32002_lo.totsky
ad57003040s000102h_lo.img ad57003040s000202m_lo.img ad57003040s100102h_lo.img ad57003040s100202m_lo.img-> Summing the following images to produce ad57003040sis32002_hi.totsky
ad57003040s000102h_hi.img ad57003040s000202m_hi.img ad57003040s100102h_hi.img ad57003040s100202m_hi.img-> Running XIMAGE to create ad57003040sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad57003040sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad57003040sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 164.498 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 164 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "GC_REG_6_N5" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 October 1, 1999 Exposure: 19643.3 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 2810 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 16.0000 16 0 ![11]XIMAGE> exit-> Summing gis images
ad57003040g200170h.expo ad57003040g200270m.expo ad57003040g300170h.expo ad57003040g300270m.expo-> Summing the following images to produce ad57003040gis25670_all.totsky
ad57003040g200170h.img ad57003040g200270m.img ad57003040g300170h.img ad57003040g300270m.img-> Summing the following images to produce ad57003040gis25670_lo.totsky
ad57003040g200170h_lo.img ad57003040g200270m_lo.img ad57003040g300170h_lo.img ad57003040g300270m_lo.img-> Summing the following images to produce ad57003040gis25670_hi.totsky
ad57003040g200170h_hi.img ad57003040g200270m_hi.img ad57003040g300170h_hi.img ad57003040g300270m_hi.img-> Running XIMAGE to create ad57003040gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad57003040gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 8.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 8 min: 0 ![2]XIMAGE> read/exp_map ad57003040gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 344.073 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 344 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "GC_REG_6_N5" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 October 1, 1999 Exposure: 20644.3 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 6.00000 60 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 17.0000 17 0 ![11]XIMAGE> exit
-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad57003040gis25670.src
-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad57003040sis32002.src
1 ad57003040s000102h.evt 3158 2 ad57003040s000202m.evt 568-> Fetching SIS0_NOTCHIP2.1
ad57003040s000102h.evt-> Grouping ad57003040s010102_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7521.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20923 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 18 are grouped by a factor 2 ... 19 - 26 are grouped by a factor 4 ... 27 - 30 are grouped by a factor 2 ... 31 - 35 are single channels ... 36 - 37 are grouped by a factor 2 ... 38 - 38 are single channels ... 39 - 40 are grouped by a factor 2 ... 41 - 50 are single channels ... 51 - 72 are grouped by a factor 2 ... 73 - 76 are grouped by a factor 4 ... 77 - 79 are grouped by a factor 3 ... 80 - 87 are grouped by a factor 4 ... 88 - 90 are grouped by a factor 3 ... 91 - 105 are grouped by a factor 5 ... 106 - 117 are grouped by a factor 6 ... 118 - 122 are grouped by a factor 5 ... 123 - 128 are grouped by a factor 6 ... 129 - 148 are grouped by a factor 10 ... 149 - 160 are grouped by a factor 12 ... 161 - 173 are grouped by a factor 13 ... 174 - 192 are grouped by a factor 19 ... 193 - 217 are grouped by a factor 25 ... 218 - 246 are grouped by a factor 29 ... 247 - 337 are grouped by a factor 91 ... 338 - 511 are grouped by a factor 174 ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s010102_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data files: ecd = ./sis0c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.491387715307117 rmf1.tmp 0.508612284692883-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
4.914E-01 * rmf0.tmp
5.086E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.49
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.51
ASCA SIS0 NONE NONE PI
-> Generating ad57003040s010102_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 232 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.068 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 3.06300E+03
Weighted mean angle from optical axis = 8.567 arcmin
-> SIS0_NOTCHIP2.1 already present in current directoryad57003040s000202m.evt-> Grouping ad57003040s010202_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 2251.7 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20923 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 44 are grouped by a factor 28 ... 45 - 48 are grouped by a factor 4 ... 49 - 51 are grouped by a factor 3 ... 52 - 59 are grouped by a factor 4 ... 60 - 64 are grouped by a factor 5 ... 65 - 70 are grouped by a factor 6 ... 71 - 79 are grouped by a factor 9 ... 80 - 99 are grouped by a factor 20 ... 100 - 118 are grouped by a factor 19 ... 119 - 143 are grouped by a factor 25 ... 144 - 175 are grouped by a factor 32 ... 176 - 271 are grouped by a factor 96 ... 272 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s010202_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data files: ecd = ./sis0c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.5 rmf1.tmp 0.5-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
5.000E-01 * rmf0.tmp
5.000E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.50
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.50
ASCA SIS0 NONE NONE PI
-> Generating ad57003040s010202_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 232 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.068 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.50000E+02
Weighted mean angle from optical axis = 8.568 arcmin
-> Standard Output From STOOL group_event_files:1 ad57003040s000112h.evt 3346 2 ad57003040s000212m.evt 604-> SIS0_NOTCHIP2.1 already present in current directory
ad57003040s000112h.evt-> Grouping ad57003040s010312_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7521.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20923 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 37 are grouped by a factor 6 ... 38 - 45 are grouped by a factor 8 ... 46 - 51 are grouped by a factor 6 ... 52 - 60 are grouped by a factor 3 ... 61 - 62 are grouped by a factor 2 ... 63 - 65 are grouped by a factor 3 ... 66 - 71 are grouped by a factor 2 ... 72 - 74 are grouped by a factor 3 ... 75 - 100 are grouped by a factor 2 ... 101 - 109 are grouped by a factor 3 ... 110 - 111 are grouped by a factor 2 ... 112 - 129 are grouped by a factor 3 ... 130 - 139 are grouped by a factor 5 ... 140 - 143 are grouped by a factor 4 ... 144 - 148 are grouped by a factor 5 ... 149 - 162 are grouped by a factor 7 ... 163 - 168 are grouped by a factor 6 ... 169 - 176 are grouped by a factor 8 ... 177 - 182 are grouped by a factor 6 ... 183 - 212 are grouped by a factor 10 ... 213 - 234 are grouped by a factor 11 ... 235 - 243 are grouped by a factor 9 ... 244 - 254 are grouped by a factor 11 ... 255 - 274 are grouped by a factor 20 ... 275 - 290 are grouped by a factor 16 ... 291 - 311 are grouped by a factor 21 ... 312 - 329 are grouped by a factor 18 ... 330 - 351 are grouped by a factor 22 ... 352 - 388 are grouped by a factor 37 ... 389 - 436 are grouped by a factor 48 ... 437 - 483 are grouped by a factor 47 ... 484 - 603 are grouped by a factor 120 ... 604 - 842 are grouped by a factor 239 ... 843 - 1001 are grouped by a factor 159 ... 1002 - 1023 are grouped by a factor 22 ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s010312_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data files: ecd = ./sis0c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.49662783568363 rmf1.tmp 0.50337216431637-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
4.966E-01 * rmf0.tmp
5.034E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.50
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.50
ASCA SIS0 NONE NONE PI
-> Generating ad57003040s010312_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 232 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.068 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 3.24500E+03
Weighted mean angle from optical axis = 8.609 arcmin
-> SIS0_NOTCHIP2.1 already present in current directoryad57003040s000212m.evt-> Grouping ad57003040s010412_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 2251.7 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20923 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 88 are grouped by a factor 57 ... 89 - 102 are grouped by a factor 7 ... 103 - 110 are grouped by a factor 8 ... 111 - 119 are grouped by a factor 9 ... 120 - 139 are grouped by a factor 10 ... 140 - 155 are grouped by a factor 16 ... 156 - 229 are grouped by a factor 37 ... 230 - 272 are grouped by a factor 43 ... 273 - 327 are grouped by a factor 55 ... 328 - 433 are grouped by a factor 106 ... 434 - 834 are grouped by a factor 401 ... 835 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s010412_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data files: ecd = ./sis0c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.50253807106599 rmf1.tmp 0.49746192893401-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
5.025E-01 * rmf0.tmp
4.975E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.50
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.50
ASCA SIS0 NONE NONE PI
-> Generating ad57003040s010412_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 232 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.068 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.85000E+02
Weighted mean angle from optical axis = 8.537 arcmin
-> Standard Output From STOOL group_event_files:1 ad57003040s100102h.evt 3441 2 ad57003040s100202m.evt 661-> Fetching SIS1_NOTCHIP2.1
ad57003040s100102h.evt-> Grouping ad57003040s110102_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7586.2 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20872 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 24 are grouped by a factor 4 ... 25 - 30 are grouped by a factor 2 ... 31 - 58 are single channels ... 59 - 74 are grouped by a factor 2 ... 75 - 77 are grouped by a factor 3 ... 78 - 81 are grouped by a factor 4 ... 82 - 84 are grouped by a factor 3 ... 85 - 90 are grouped by a factor 6 ... 91 - 93 are grouped by a factor 3 ... 94 - 99 are grouped by a factor 6 ... 100 - 104 are grouped by a factor 5 ... 105 - 110 are grouped by a factor 6 ... 111 - 117 are grouped by a factor 7 ... 118 - 125 are grouped by a factor 8 ... 126 - 131 are grouped by a factor 6 ... 132 - 141 are grouped by a factor 10 ... 142 - 153 are grouped by a factor 12 ... 154 - 181 are grouped by a factor 14 ... 182 - 211 are grouped by a factor 30 ... 212 - 251 are grouped by a factor 40 ... 252 - 329 are grouped by a factor 78 ... 330 - 472 are grouped by a factor 143 ... 473 - 511 are grouped by a factor 39 ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s110102_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data files: ecd = ./sis1c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.41027926322044 rmf1.tmp 0.58972073677956-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
4.103E-01 * rmf0.tmp
5.897E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.41
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.59
ASCA SIS1 NONE NONE PI
-> Generating ad57003040s110102_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 656 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.032 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 3.34700E+03
Weighted mean angle from optical axis = 9.074 arcmin
-> SIS1_NOTCHIP2.1 already present in current directoryad57003040s100202m.evt-> Grouping ad57003040s110202_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 2283.7 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20872 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 44 are grouped by a factor 28 ... 45 - 48 are grouped by a factor 4 ... 49 - 57 are grouped by a factor 3 ... 58 - 65 are grouped by a factor 4 ... 66 - 79 are grouped by a factor 7 ... 80 - 90 are grouped by a factor 11 ... 91 - 107 are grouped by a factor 17 ... 108 - 129 are grouped by a factor 22 ... 130 - 159 are grouped by a factor 30 ... 160 - 239 are grouped by a factor 80 ... 240 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s110202_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data files: ecd = ./sis1c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.400311526479751 rmf1.tmp 0.599688473520249-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
4.003E-01 * rmf0.tmp
5.997E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.40
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.60
ASCA SIS1 NONE NONE PI
-> Generating ad57003040s110202_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 656 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.032 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.39000E+02
Weighted mean angle from optical axis = 9.111 arcmin
-> Standard Output From STOOL group_event_files:1 ad57003040s100112h.evt 3705 2 ad57003040s100212m.evt 708-> SIS1_NOTCHIP2.1 already present in current directory
ad57003040s100112h.evt-> Grouping ad57003040s110312_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7586.2 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20872 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 41 are grouped by a factor 9 ... 42 - 48 are grouped by a factor 7 ... 49 - 52 are grouped by a factor 4 ... 53 - 55 are grouped by a factor 3 ... 56 - 69 are grouped by a factor 2 ... 70 - 71 are single channels ... 72 - 77 are grouped by a factor 2 ... 78 - 78 are single channels ... 79 - 112 are grouped by a factor 2 ... 113 - 118 are grouped by a factor 3 ... 119 - 122 are grouped by a factor 4 ... 123 - 128 are grouped by a factor 2 ... 129 - 131 are grouped by a factor 3 ... 132 - 135 are grouped by a factor 4 ... 136 - 141 are grouped by a factor 3 ... 142 - 145 are grouped by a factor 4 ... 146 - 151 are grouped by a factor 6 ... 152 - 156 are grouped by a factor 5 ... 157 - 163 are grouped by a factor 7 ... 164 - 168 are grouped by a factor 5 ... 169 - 177 are grouped by a factor 9 ... 178 - 184 are grouped by a factor 7 ... 185 - 193 are grouped by a factor 9 ... 194 - 203 are grouped by a factor 10 ... 204 - 210 are grouped by a factor 7 ... 211 - 221 are grouped by a factor 11 ... 222 - 231 are grouped by a factor 10 ... 232 - 246 are grouped by a factor 15 ... 247 - 257 are grouped by a factor 11 ... 258 - 274 are grouped by a factor 17 ... 275 - 293 are grouped by a factor 19 ... 294 - 311 are grouped by a factor 18 ... 312 - 363 are grouped by a factor 26 ... 364 - 418 are grouped by a factor 55 ... 419 - 486 are grouped by a factor 68 ... 487 - 612 are grouped by a factor 126 ... 613 - 818 are grouped by a factor 206 ... 819 - 956 are grouped by a factor 138 ... 957 - 1023 are grouped by a factor 67 ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s110312_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data files: ecd = ./sis1c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.40897824290829 rmf1.tmp 0.59102175709171-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
4.090E-01 * rmf0.tmp
5.910E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.41
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.59
ASCA SIS1 NONE NONE PI
-> Generating ad57003040s110312_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 656 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.032 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 3.61000E+03
Weighted mean angle from optical axis = 9.074 arcmin
-> SIS1_NOTCHIP2.1 already present in current directoryad57003040s100212m.evt-> Grouping ad57003040s110412_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 2283.7 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20872 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 87 are grouped by a factor 55 ... 88 - 93 are grouped by a factor 6 ... 94 - 98 are grouped by a factor 5 ... 99 - 110 are grouped by a factor 6 ... 111 - 115 are grouped by a factor 5 ... 116 - 123 are grouped by a factor 8 ... 124 - 132 are grouped by a factor 9 ... 133 - 158 are grouped by a factor 13 ... 159 - 176 are grouped by a factor 18 ... 177 - 202 are grouped by a factor 26 ... 203 - 250 are grouped by a factor 48 ... 251 - 301 are grouped by a factor 51 ... 302 - 439 are grouped by a factor 138 ... 440 - 901 are grouped by a factor 462 ... 902 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040s110412_0.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data files: ecd = ./sis1c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.391872278664732 rmf1.tmp 0.608127721335268-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
3.919E-01 * rmf0.tmp
6.081E-01 * rmf1.tmp
RMF # 1 : rmf0.tmp 0.39
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.61
ASCA SIS1 NONE NONE PI
-> Generating ad57003040s110412_0.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 53 by 108 bins
expanded to 53 by 108 bins
First WMAP bin is at detector pixel 656 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 15.032 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.86000E+02
Weighted mean angle from optical axis = 9.034 arcmin
-> Standard Output From STOOL group_event_files:1 ad57003040g200170h.evt 13356 1 ad57003040g200270m.evt 13356-> GIS2_REGION256.4 already present in current directory
ad57003040g200170h.evt ad57003040g200270m.evt-> Correcting ad57003040g210170_0.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad57003040g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 10322. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 21 are grouped by a factor 22 ... 22 - 23 are grouped by a factor 2 ... 24 - 29 are grouped by a factor 3 ... 30 - 33 are grouped by a factor 4 ... 34 - 57 are grouped by a factor 3 ... 58 - 69 are grouped by a factor 2 ... 70 - 70 are single channels ... 71 - 72 are grouped by a factor 2 ... 73 - 168 are single channels ... 169 - 170 are grouped by a factor 2 ... 171 - 176 are single channels ... 177 - 186 are grouped by a factor 2 ... 187 - 187 are single channels ... 188 - 199 are grouped by a factor 2 ... 200 - 200 are single channels ... 201 - 222 are grouped by a factor 2 ... 223 - 225 are grouped by a factor 3 ... 226 - 231 are grouped by a factor 2 ... 232 - 234 are grouped by a factor 3 ... 235 - 242 are grouped by a factor 2 ... 243 - 245 are grouped by a factor 3 ... 246 - 259 are grouped by a factor 2 ... 260 - 280 are grouped by a factor 3 ... 281 - 282 are grouped by a factor 2 ... 283 - 288 are grouped by a factor 3 ... 289 - 328 are grouped by a factor 4 ... 329 - 331 are grouped by a factor 3 ... 332 - 339 are grouped by a factor 4 ... 340 - 349 are grouped by a factor 5 ... 350 - 353 are grouped by a factor 4 ... 354 - 359 are grouped by a factor 6 ... 360 - 369 are grouped by a factor 5 ... 370 - 373 are grouped by a factor 4 ... 374 - 393 are grouped by a factor 5 ... 394 - 399 are grouped by a factor 6 ... 400 - 414 are grouped by a factor 5 ... 415 - 420 are grouped by a factor 6 ... 421 - 427 are grouped by a factor 7 ... 428 - 436 are grouped by a factor 9 ... 437 - 443 are grouped by a factor 7 ... 444 - 449 are grouped by a factor 6 ... 450 - 463 are grouped by a factor 7 ... 464 - 473 are grouped by a factor 10 ... 474 - 480 are grouped by a factor 7 ... 481 - 489 are grouped by a factor 9 ... 490 - 505 are grouped by a factor 8 ... 506 - 514 are grouped by a factor 9 ... 515 - 524 are grouped by a factor 10 ... 525 - 536 are grouped by a factor 12 ... 537 - 546 are grouped by a factor 10 ... 547 - 560 are grouped by a factor 14 ... 561 - 571 are grouped by a factor 11 ... 572 - 581 are grouped by a factor 10 ... 582 - 596 are grouped by a factor 15 ... 597 - 610 are grouped by a factor 14 ... 611 - 634 are grouped by a factor 24 ... 635 - 676 are grouped by a factor 21 ... 677 - 694 are grouped by a factor 18 ... 695 - 724 are grouped by a factor 30 ... 725 - 765 are grouped by a factor 41 ... 766 - 812 are grouped by a factor 47 ... 813 - 870 are grouped by a factor 58 ... 871 - 929 are grouped by a factor 59 ... 930 - 984 are grouped by a factor 55 ... 985 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040g210170_0.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 1 1
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.33560E+04
Weighted mean angle from optical axis = 13.136 arcmin
-> Standard Output From STOOL group_event_files:1 ad57003040g300170h.evt 14339 1 ad57003040g300270m.evt 14339-> GIS3_REGION256.4 already present in current directory
ad57003040g300170h.evt ad57003040g300270m.evt-> Correcting ad57003040g310170_0.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad57003040g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 10322. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 21 are grouped by a factor 22 ... 22 - 29 are grouped by a factor 2 ... 30 - 53 are grouped by a factor 3 ... 54 - 55 are grouped by a factor 2 ... 56 - 58 are grouped by a factor 3 ... 59 - 66 are grouped by a factor 2 ... 67 - 69 are single channels ... 70 - 71 are grouped by a factor 2 ... 72 - 179 are single channels ... 180 - 183 are grouped by a factor 2 ... 184 - 185 are single channels ... 186 - 187 are grouped by a factor 2 ... 188 - 188 are single channels ... 189 - 190 are grouped by a factor 2 ... 191 - 191 are single channels ... 192 - 237 are grouped by a factor 2 ... 238 - 243 are grouped by a factor 3 ... 244 - 249 are grouped by a factor 2 ... 250 - 252 are grouped by a factor 3 ... 253 - 254 are grouped by a factor 2 ... 255 - 260 are grouped by a factor 3 ... 261 - 262 are grouped by a factor 2 ... 263 - 274 are grouped by a factor 3 ... 275 - 278 are grouped by a factor 2 ... 279 - 287 are grouped by a factor 3 ... 288 - 291 are grouped by a factor 4 ... 292 - 306 are grouped by a factor 3 ... 307 - 310 are grouped by a factor 4 ... 311 - 313 are grouped by a factor 3 ... 314 - 341 are grouped by a factor 4 ... 342 - 346 are grouped by a factor 5 ... 347 - 349 are grouped by a factor 3 ... 350 - 353 are grouped by a factor 4 ... 354 - 358 are grouped by a factor 5 ... 359 - 370 are grouped by a factor 4 ... 371 - 385 are grouped by a factor 5 ... 386 - 391 are grouped by a factor 6 ... 392 - 395 are grouped by a factor 4 ... 396 - 400 are grouped by a factor 5 ... 401 - 406 are grouped by a factor 6 ... 407 - 421 are grouped by a factor 5 ... 422 - 427 are grouped by a factor 6 ... 428 - 432 are grouped by a factor 5 ... 433 - 436 are grouped by a factor 4 ... 437 - 442 are grouped by a factor 6 ... 443 - 447 are grouped by a factor 5 ... 448 - 461 are grouped by a factor 7 ... 462 - 470 are grouped by a factor 9 ... 471 - 476 are grouped by a factor 6 ... 477 - 492 are grouped by a factor 8 ... 493 - 499 are grouped by a factor 7 ... 500 - 509 are grouped by a factor 10 ... 510 - 520 are grouped by a factor 11 ... 521 - 540 are grouped by a factor 10 ... 541 - 558 are grouped by a factor 9 ... 559 - 566 are grouped by a factor 8 ... 567 - 576 are grouped by a factor 10 ... 577 - 598 are grouped by a factor 11 ... 599 - 613 are grouped by a factor 15 ... 614 - 636 are grouped by a factor 23 ... 637 - 655 are grouped by a factor 19 ... 656 - 676 are grouped by a factor 21 ... 677 - 698 are grouped by a factor 22 ... 699 - 723 are grouped by a factor 25 ... 724 - 757 are grouped by a factor 34 ... 758 - 793 are grouped by a factor 36 ... 794 - 848 are grouped by a factor 55 ... 849 - 892 are grouped by a factor 44 ... 893 - 944 are grouped by a factor 52 ... 945 - 1023 are grouped by a factor 79 ... --------------------------------------------- ... ...... exiting, changes written to file : ad57003040g310170_0.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 1 1
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.43390E+04
Weighted mean angle from optical axis = 13.235 arcmin
-> Plotting ad57003040g210170_0_pi.ps from ad57003040g210170_0.pi
XSPEC 9.01 19:55:34 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040g210170_0.pi
Net count rate (cts/s) for file 1 1.294 +/- 1.1209E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040g310170_0_pi.ps from ad57003040g310170_0.pi
XSPEC 9.01 19:55:45 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040g310170_0.pi
Net count rate (cts/s) for file 1 1.389 +/- 1.1601E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s010102_0_pi.ps from ad57003040s010102_0.pi
XSPEC 9.01 19:55:55 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s010102_0.pi
Net count rate (cts/s) for file 1 0.4091 +/- 7.3878E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s010202_0_pi.ps from ad57003040s010202_0.pi
XSPEC 9.01 19:56:06 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s010202_0.pi
Net count rate (cts/s) for file 1 0.2469 +/- 1.2538E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s010312_0_pi.ps from ad57003040s010312_0.pi
XSPEC 9.01 19:56:19 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s010312_0.pi
Net count rate (cts/s) for file 1 0.4337 +/- 7.6175E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s010412_0_pi.ps from ad57003040s010412_0.pi
XSPEC 9.01 19:56:35 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s010412_0.pi
Net count rate (cts/s) for file 1 0.2625 +/- 1.2608E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s110102_0_pi.ps from ad57003040s110102_0.pi
XSPEC 9.01 19:56:51 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s110102_0.pi
Net count rate (cts/s) for file 1 0.4437 +/- 7.6625E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s110202_0_pi.ps from ad57003040s110202_0.pi
XSPEC 9.01 19:57:06 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s110202_0.pi
Net count rate (cts/s) for file 1 0.2811 +/- 1.3188E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s110312_0_pi.ps from ad57003040s110312_0.pi
XSPEC 9.01 19:57:20 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s110312_0.pi
Net count rate (cts/s) for file 1 0.4786 +/- 7.9704E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad57003040s110412_0_pi.ps from ad57003040s110412_0.pi
XSPEC 9.01 19:57:35 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad57003040s110412_0.pi
Net count rate (cts/s) for file 1 0.3017 +/- 1.2676E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad57003040s000002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GC_REG_6_N5 Start Time (d) .... 11452 10:13:09.511
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11452 19:48:37.511
No. of Rows ....... 78 Bin Time (s) ...... 131.2
Right Ascension ... 2.6803E+02 Internal time sys.. Converted to TJD
Declination ....... -2.9497E+01 Experiment ........ ASCA SIS0
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 264 Newbins of 131.152 (s)
Intv 1 Start11452 10:14:15
Ser.1 Avg 0.3685 Chisq 728.3 Var 0.3019E-01 Newbs. 78
Min 0.1638 Max 1.729 expVar 0.3234E-02 Bins 78
Results from Statistical Analysis
Newbin Integration Time (s).. 131.15
Interval Duration (s)........ 34362.
No. of Newbins .............. 78
Average (c/s) ............... 0.36853 +/- 0.65E-02
Standard Deviation (c/s)..... 0.17376
Minimum (c/s)................ 0.16381
Maximum (c/s)................ 1.7292
Variance ((c/s)**2).......... 0.30192E-01 +/- 0.49E-02
Expected Variance ((c/s)**2). 0.32337E-02 +/- 0.52E-03
Third Moment ((c/s)**3)...... 0.31924E-01
Average Deviation (c/s)...... 0.82132E-01
Skewness..................... 6.0851 +/- 0.28
Kurtosis..................... 45.321 +/- 0.55
RMS fractional variation..... 0.44553 +/- 0.40E-01
Chi-Square................... 728.27 dof 77
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.34297E-12 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 264 Newbins of 131.152 (s)
Intv 1 Start11452 10:14:15
Ser.1 Avg 0.3685 Chisq 728.3 Var 0.3019E-01 Newbs. 78
Min 0.1638 Max 1.729 expVar 0.3234E-02 Bins 78
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad57003040s000002_0.lc
PLT> hard /ps
PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=8.0000000000E+00 for ad57003040s100102h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad57003040s100002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GC_REG_6_N5 Start Time (d) .... 11452 10:13:09.511
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11452 19:48:37.511
No. of Rows ....... 85 Bin Time (s) ...... 120.3
Right Ascension ... 2.6803E+02 Internal time sys.. Converted to TJD
Declination ....... -2.9497E+01 Experiment ........ ASCA SIS1
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 288 Newbins of 120.306 (s)
Intv 1 Start11452 10:14: 9
Ser.1 Avg 0.4107 Chisq 221.0 Var 0.9787E-02 Newbs. 85
Min 0.1912 Max 0.6899 expVar 0.3765E-02 Bins 85
Results from Statistical Analysis
Newbin Integration Time (s).. 120.31
Interval Duration (s)........ 34407.
No. of Newbins .............. 85
Average (c/s) ............... 0.41075 +/- 0.67E-02
Standard Deviation (c/s)..... 0.98930E-01
Minimum (c/s)................ 0.19118
Maximum (c/s)................ 0.68991
Variance ((c/s)**2).......... 0.97871E-02 +/- 0.15E-02
Expected Variance ((c/s)**2). 0.37651E-02 +/- 0.58E-03
Third Moment ((c/s)**3)...... 0.42422E-04
Average Deviation (c/s)...... 0.77990E-01
Skewness..................... 0.43814E-01 +/- 0.27
Kurtosis.....................-0.13765 +/- 0.53
RMS fractional variation..... 0.18893 +/- 0.24E-01
Chi-Square................... 220.95 dof 84
Chi-Square Prob of constancy. 0.29395E-13 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.32477E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 288 Newbins of 120.306 (s)
Intv 1 Start11452 10:14: 9
Ser.1 Avg 0.4107 Chisq 221.0 Var 0.9787E-02 Newbs. 85
Min 0.1912 Max 0.6899 expVar 0.3765E-02 Bins 85
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad57003040s100002_0.lc
PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad57003040g200170h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad57003040g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GC_REG_6_N5 Start Time (d) .... 11452 10:13:09.511
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11452 19:49:41.511
No. of Rows ....... 267 Bin Time (s) ...... 38.64
Right Ascension ... 2.6803E+02 Internal time sys.. Converted to TJD
Declination ....... -2.9497E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 67.6418 (s)
Intv 1 Start11452 10:13:43
Ser.1 Avg 1.301 Chisq 129.7 Var 0.2221E-01 Newbs. 160
Min 0.9057 Max 1.811 expVar 0.2357E-01 Bins 267
Results from Statistical Analysis
Newbin Integration Time (s).. 67.642
Interval Duration (s)........ 34565.
No. of Newbins .............. 160
Average (c/s) ............... 1.3007 +/- 0.12E-01
Standard Deviation (c/s)..... 0.14902
Minimum (c/s)................ 0.90574
Maximum (c/s)................ 1.8115
Variance ((c/s)**2).......... 0.22207E-01 +/- 0.25E-02
Expected Variance ((c/s)**2). 0.23572E-01 +/- 0.26E-02
Third Moment ((c/s)**3)...... 0.15896E-02
Average Deviation (c/s)...... 0.11810
Skewness..................... 0.48035 +/- 0.19
Kurtosis..................... 0.69943 +/- 0.39
RMS fractional variation....< 0.77246E-01 (3 sigma)
Chi-Square................... 129.70 dof 159
Chi-Square Prob of constancy. 0.95712 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.66154E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 67.6418 (s)
Intv 1 Start11452 10:13:43
Ser.1 Avg 1.301 Chisq 129.7 Var 0.2221E-01 Newbs. 160
Min 0.9057 Max 1.811 expVar 0.2357E-01 Bins 267
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad57003040g200070_0.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad57003040g300170h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad57003040g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GC_REG_6_N5 Start Time (d) .... 11452 10:13:09.511
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11452 19:49:41.511
No. of Rows ....... 287 Bin Time (s) ...... 35.99
Right Ascension ... 2.6803E+02 Internal time sys.. Converted to TJD
Declination ....... -2.9497E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 67.6418 (s)
Intv 1 Start11452 10:13:43
Ser.1 Avg 1.386 Chisq 189.6 Var 0.2699E-01 Newbs. 157
Min 0.9268 Max 1.792 expVar 0.2293E-01 Bins 287
Results from Statistical Analysis
Newbin Integration Time (s).. 67.642
Interval Duration (s)........ 34565.
No. of Newbins .............. 157
Average (c/s) ............... 1.3864 +/- 0.12E-01
Standard Deviation (c/s)..... 0.16429
Minimum (c/s)................ 0.92683
Maximum (c/s)................ 1.7920
Variance ((c/s)**2).......... 0.26992E-01 +/- 0.31E-02
Expected Variance ((c/s)**2). 0.22934E-01 +/- 0.26E-02
Third Moment ((c/s)**3)......-0.89722E-03
Average Deviation (c/s)...... 0.13112
Skewness.....................-0.20232 +/- 0.20
Kurtosis.....................-0.41940E-01 +/- 0.39
RMS fractional variation....< 0.48459E-01 (3 sigma)
Chi-Square................... 189.59 dof 156
Chi-Square Prob of constancy. 0.34595E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.40877 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 67.6418 (s)
Intv 1 Start11452 10:13:43
Ser.1 Avg 1.386 Chisq 189.6 Var 0.2699E-01 Newbs. 157
Min 0.9268 Max 1.792 expVar 0.2293E-01 Bins 287
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad57003040g300070_0.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad57003040g200170h.evt[2] ad57003040g200270m.evt[2]-> Making L1 light curve of ft991001_0923_2012G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 20414 output records from 20429 good input G2_L1 records.-> Making L1 light curve of ft991001_0923_2012G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 9873 output records from 22854 good input G2_L1 records.-> Merging GTIs from the following files:
ad57003040g300170h.evt[2] ad57003040g300270m.evt[2]-> Making L1 light curve of ft991001_0923_2012G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 19866 output records from 19881 good input G3_L1 records.-> Making L1 light curve of ft991001_0923_2012G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 9859 output records from 22312 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 7025 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft991001_0923_2012.mkf
1 ad57003040g200170h.unf 36101 1 ad57003040g200270m.unf 36101 1 ad57003040g200370l.unf 36101-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 20:15:20 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad57003040g220170.cal
Net count rate (cts/s) for file 1 0.1300 +/- 2.3665E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.5351E+06 using 84 PHA bins.
Reduced chi-squared = 1.9936E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.5256E+06 using 84 PHA bins.
Reduced chi-squared = 1.9559E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.5256E+06 using 84 PHA bins.
Reduced chi-squared = 1.9312E+04
!XSPEC> renorm
Chi-Squared = 466.5 using 84 PHA bins.
Reduced chi-squared = 5.905
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
407.91 0 1.000 5.896 7.6447E-02 2.9487E-02
2.7495E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
287.27 0 1.000 5.882 0.1283 3.6359E-02
2.4934E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
229.96 -1 1.000 5.915 0.1572 4.5416E-02
2.0207E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
183.65 -2 1.000 5.980 0.1862 5.4332E-02
1.3676E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
171.11 -3 1.000 6.024 0.2161 5.9955E-02
9.2779E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
170.62 -4 1.000 6.033 0.2259 6.0964E-02
8.3593E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
170.60 -5 1.000 6.033 0.2276 6.1002E-02
8.3551E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
170.60 1 1.000 6.033 0.2276 6.1002E-02
8.3552E-03
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 6.03330 +/- 0.15074E-01
3 3 2 gaussian/b Sigma 0.227614 +/- 0.14939E-01
4 4 2 gaussian/b norm 6.100196E-02 +/- 0.22120E-02
5 2 3 gaussian/b LineE 6.64270 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.238833 = par 3 * 1.0493
7 5 3 gaussian/b norm 8.355208E-03 +/- 0.17448E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 170.6 using 84 PHA bins.
Reduced chi-squared = 2.160
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad57003040g220170.cal peaks at 6.03330 +/- 0.015074 keV1 ad57003040g300170h.unf 35284 1 ad57003040g300270m.unf 35284 1 ad57003040g300370l.unf 35284-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 20:16:11 5-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad57003040g320170.cal
Net count rate (cts/s) for file 1 0.1040 +/- 2.1257E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.1770E+06 using 84 PHA bins.
Reduced chi-squared = 2.8272E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.1657E+06 using 84 PHA bins.
Reduced chi-squared = 2.7765E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.1657E+06 using 84 PHA bins.
Reduced chi-squared = 2.7414E+04
!XSPEC> renorm
Chi-Squared = 700.1 using 84 PHA bins.
Reduced chi-squared = 8.862
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
593.90 0 1.000 5.893 7.7766E-02 2.2737E-02
1.9437E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
264.33 0 1.000 5.863 0.1323 3.6491E-02
1.6469E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
146.16 -1 1.000 5.876 0.1637 5.2109E-02
1.1605E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
142.30 -2 1.000 5.890 0.1720 5.5611E-02
9.3291E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
142.12 -3 1.000 5.885 0.1670 5.5127E-02
9.8249E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
142.11 -4 1.000 5.887 0.1683 5.5300E-02
9.6329E-03
Due to zero model norms
fit parameter 1 is temporarily frozen
142.10 -5 1.000 5.886 0.1677 5.5239E-02
9.6965E-03
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.88631 +/- 0.12198E-01
3 3 2 gaussian/b Sigma 0.167726 +/- 0.14022E-01
4 4 2 gaussian/b norm 5.523858E-02 +/- 0.19636E-02
5 2 3 gaussian/b LineE 6.48085 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.175993 = par 3 * 1.0493
7 5 3 gaussian/b norm 9.696525E-03 +/- 0.13797E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 142.1 using 84 PHA bins.
Reduced chi-squared = 1.799
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad57003040g320170.cal peaks at 5.88631 +/- 0.012198 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17763
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 91 10938
Flickering pixels iter, pixels & cnts : 1 55 762
cleaning chip # 1
Hot pixels & counts : 53 5402
Flickering pixels iter, pixels & cnts : 1 46 476
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
NOTE: Underflow during cummulative Poisson Prob. computation
Number of pixels rejected : 245
Number of (internal) image counts : 17763
Number of image cts rejected (N, %) : 1757898.96
By chip : 0 1 2 3
Pixels rejected : 146 99 0 0
Image counts : 11780 5982 0 1
Image cts rejected: 11700 5878 0 0
Image cts rej (%) : 99.32 98.26 0.00 0.00
filtering data...
Total counts : 11780 5982 0 1
Total cts rejected: 11700 5878 0 0
Total cts rej (%) : 99.32 98.26 0.00 0.00
Number of clean counts accepted : 185
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 245
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17817
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 91 10965
Flickering pixels iter, pixels & cnts : 1 55 764
cleaning chip # 1
Hot pixels & counts : 53 5402
Flickering pixels iter, pixels & cnts : 1 46 476
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
NOTE: Underflow during cummulative Poisson Prob. computation
Number of pixels rejected : 245
Number of (internal) image counts : 17817
Number of image cts rejected (N, %) : 1760798.82
By chip : 0 1 2 3
Pixels rejected : 146 99 0 0
Image counts : 11822 5994 0 1
Image cts rejected: 11729 5878 0 0
Image cts rej (%) : 99.21 98.06 0.00 0.00
filtering data...
Total counts : 11822 5994 0 1
Total cts rejected: 11729 5878 0 0
Total cts rej (%) : 99.21 98.06 0.00 0.00
Number of clean counts accepted : 210
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 245
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4270
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 3576
Flickering pixels iter, pixels & cnts : 1 6 58
cleaning chip # 1
Hot pixels & counts : 2 478
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 4270
Number of image cts rejected (N, %) : 411596.37
By chip : 0 1 2 3
Pixels rejected : 17 3 0 0
Image counts : 3698 572 0 0
Image cts rejected: 3634 481 0 0
Image cts rej (%) : 98.27 84.09 0.00 0.00
filtering data...
Total counts : 3698 572 0 0
Total cts rejected: 3634 481 0 0
Total cts rej (%) : 98.27 84.09 0.00 0.00
Number of clean counts accepted : 155
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4322
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 3588
Flickering pixels iter, pixels & cnts : 1 6 63
cleaning chip # 1
Hot pixels & counts : 2 481
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 4322
Number of image cts rejected (N, %) : 413595.67
By chip : 0 1 2 3
Pixels rejected : 17 3 0 0
Image counts : 3727 595 0 0
Image cts rejected: 3651 484 0 0
Image cts rej (%) : 97.96 81.34 0.00 0.00
filtering data...
Total counts : 3727 595 0 0
Total cts rejected: 3651 484 0 0
Total cts rej (%) : 97.96 81.34 0.00 0.00
Number of clean counts accepted : 187
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 2361
Total counts in chip images : 2360
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 9 1595
Flickering pixels iter, pixels & cnts : 1 1 5
cleaning chip # 1
Hot pixels & counts : 3 586
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 13
Number of (internal) image counts : 2360
Number of image cts rejected (N, %) : 218692.63
By chip : 0 1 2 3
Pixels rejected : 10 3 0 0
Image counts : 1698 662 0 0
Image cts rejected: 1600 586 0 0
Image cts rej (%) : 94.23 88.52 0.00 0.00
filtering data...
Total counts : 1699 662 0 0
Total cts rejected: 1601 586 0 0
Total cts rej (%) : 94.23 88.52 0.00 0.00
Number of clean counts accepted : 174
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2424
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 9 1597
Flickering pixels iter, pixels & cnts : 1 1 5
cleaning chip # 1
Hot pixels & counts : 3 589
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 13
Number of (internal) image counts : 2424
Number of image cts rejected (N, %) : 219190.39
By chip : 0 1 2 3
Pixels rejected : 10 3 0 0
Image counts : 1730 694 0 0
Image cts rejected: 1602 589 0 0
Image cts rej (%) : 92.60 84.87 0.00 0.00
filtering data...
Total counts : 1730 694 0 0
Total cts rejected: 1602 589 0 0
Total cts rej (%) : 92.60 84.87 0.00 0.00
Number of clean counts accepted : 233
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 25198
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 98 11826
Flickering pixels iter, pixels & cnts : 1 77 1294
cleaning chip # 1
Hot pixels & counts : 91 10831
Flickering pixels iter, pixels & cnts : 1 70 1034
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 336
Number of (internal) image counts : 25198
Number of image cts rejected (N, %) : 2498599.15
By chip : 0 1 2 3
Pixels rejected : 175 161 0 0
Image counts : 13211 11987 0 0
Image cts rejected: 13120 11865 0 0
Image cts rej (%) : 99.31 98.98 0.00 0.00
filtering data...
Total counts : 13211 11987 0 0
Total cts rejected: 13120 11865 0 0
Total cts rej (%) : 99.31 98.98 0.00 0.00
Number of clean counts accepted : 213
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 336
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 25336
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 99 11913
Flickering pixels iter, pixels & cnts : 1 76 1265
cleaning chip # 1
Hot pixels & counts : 91 10884
Flickering pixels iter, pixels & cnts : 1 70 1037
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 336
Number of (internal) image counts : 25336
Number of image cts rejected (N, %) : 2509999.06
By chip : 0 1 2 3
Pixels rejected : 175 161 0 0
Image counts : 13276 12060 0 0
Image cts rejected: 13178 11921 0 0
Image cts rej (%) : 99.26 98.85 0.00 0.00
filtering data...
Total counts : 13276 12060 0 0
Total cts rejected: 13178 11921 0 0
Total cts rej (%) : 99.26 98.85 0.00 0.00
Number of clean counts accepted : 237
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 336
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1859
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 3 998
Flickering pixels iter, pixels & cnts : 1 1 4
cleaning chip # 1
Hot pixels & counts : 4 696
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1859
Number of image cts rejected (N, %) : 169891.34
By chip : 0 1 2 3
Pixels rejected : 4 4 0 0
Image counts : 1071 788 0 0
Image cts rejected: 1002 696 0 0
Image cts rej (%) : 93.56 88.32 0.00 0.00
filtering data...
Total counts : 1071 788 0 0
Total cts rejected: 1002 696 0 0
Total cts rej (%) : 93.56 88.32 0.00 0.00
Number of clean counts accepted : 161
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1919
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 3 998
Flickering pixels iter, pixels & cnts : 1 1 4
cleaning chip # 1
Hot pixels & counts : 4 725
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1919
Number of image cts rejected (N, %) : 172789.99
By chip : 0 1 2 3
Pixels rejected : 4 4 0 0
Image counts : 1084 835 0 0
Image cts rejected: 1002 725 0 0
Image cts rej (%) : 92.44 86.83 0.00 0.00
filtering data...
Total counts : 1084 835 0 0
Total cts rejected: 1002 725 0 0
Total cts rej (%) : 92.44 86.83 0.00 0.00
Number of clean counts accepted : 192
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2207
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 3 1152
Flickering pixels iter, pixels & cnts : 1 1 8
cleaning chip # 1
Hot pixels & counts : 4 870
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 2207
Number of image cts rejected (N, %) : 203091.98
By chip : 0 1 2 3
Pixels rejected : 4 4 0 0
Image counts : 1253 954 0 0
Image cts rejected: 1160 870 0 0
Image cts rej (%) : 92.58 91.19 0.00 0.00
filtering data...
Total counts : 1253 954 0 0
Total cts rejected: 1160 870 0 0
Total cts rej (%) : 92.58 91.19 0.00 0.00
Number of clean counts accepted : 177
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad57003040s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 2281
Total counts in chip images : 2280
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 3 1153
Flickering pixels iter, pixels & cnts : 1 1 8
cleaning chip # 1
Hot pixels & counts : 4 907
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 2280
Number of image cts rejected (N, %) : 206890.70
By chip : 0 1 2 3
Pixels rejected : 4 4 0 0
Image counts : 1267 1013 0 0
Image cts rejected: 1161 907 0 0
Image cts rej (%) : 91.63 89.54 0.00 0.00
filtering data...
Total counts : 1267 1014 0 0
Total cts rejected: 1161 908 0 0
Total cts rej (%) : 91.63 89.55 0.00 0.00
Number of clean counts accepted : 212
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad57003040g200170h.unfOffset of 208224004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-08-08 00:00:00.00000 Modified Julian Day = 51398.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
2011 78 4402 90 4769 1130 6759 622 2
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files