The following information is also available:
Time column is TIME ORDERED-> Fetching fa970629_1345.0030.gz
Offset of 141745527.601800 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-06-29 13:45:24.60179 Modified Julian Day = 50628.573201409722969-> leapsec.fits already present in current directory
Offset of 141870630.838300 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-07-01 00:30:26.83829 Modified Julian Day = 50630.021143961806956-> Observation begins 141745527.6018 1997-06-29 13:45:24
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 141745527.601600 141870643.838100
Data file start and stop ascatime : 141745527.601600 141870643.838100
Aspecting run start and stop ascatime : 141745527.601688 141870643.837997
Time interval averaged over (seconds) : 125116.236310
Total pointing and manuver time (sec) : 85951.984375 39164.941406
Mean boresight Euler angles : 12.813349 119.296289 19.370215
RA DEC SUN ANGLE
Mean solar position (deg) : 98.26 23.22
Mean aberration (arcsec) : -2.39 10.90
Mean sat X-axis (deg) : 157.116822 -55.359609 93.11
Mean sat Y-axis (deg) : 93.052127 16.813083 8.06
Mean sat Z-axis (deg) : 12.813349 -29.296290 97.43
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 13.034616 -29.087749 289.478394 0.521377
Minimum 12.886197 -29.378456 289.226288 0.121320
Maximum 13.049456 -29.025110 289.492188 70.304810
Sigma (RMS) 0.002328 0.004604 0.016281 2.107165
Number of ASPECT records processed = 104691
Aspecting to RA/DEC : 13.03461647 -29.08774948
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 13.035 DEC: -29.088
START TIME: SC 141745527.6017 = UT 1997-06-29 13:45:27
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500105 18.515 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
542.998413 19.047 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
692.997925 18.022 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
712.997925 16.956 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
732.997803 15.865 9888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
748.997620 14.712 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
764.997559 13.639 9888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
780.997559 12.508 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
796.997559 11.471 9888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
812.997437 10.453 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
832.997437 9.301 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
852.997375 8.191 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
876.997314 7.021 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
900.997070 5.997 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
928.997131 4.947 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
964.996887 3.850 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1004.996887 2.848 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1064.996582 1.843 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1156.996338 0.840 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2284.992676 0.625 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
6332.979004 0.941 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
8028.973633 0.363 C08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0
12092.959961 0.318 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
13788.955078 0.281 C08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0
17788.941406 0.235 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
19524.937500 0.237 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
23548.923828 0.235 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
25272.917969 0.253 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
29308.906250 0.226 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
31022.900391 0.278 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
35020.890625 0.251 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
36780.882812 0.291 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
40764.871094 0.268 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
42520.867188 0.330 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
46524.855469 0.278 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
48268.847656 0.339 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
52268.835938 0.313 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
54018.832031 0.366 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
58012.820312 0.331 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
59766.812500 0.363 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
63748.800781 0.329 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
65516.796875 0.346 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
69494.781250 0.303 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
71264.781250 0.316 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
75244.765625 0.267 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
77012.757812 0.295 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
80984.750000 0.232 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
82762.742188 0.270 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
86780.734375 0.219 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
88510.726562 0.244 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
92476.710938 0.204 D888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 3
94260.710938 0.217 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
98220.695312 0.174 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
100012.679688 0.185 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
103996.609375 0.166 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
105758.578125 0.175 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
109948.507812 0.166 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
111506.476562 0.193 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
115516.406250 0.177 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
117260.375000 0.231 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
121212.304688 0.181 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
123004.273438 0.223 C08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0
125100.234375 3.903 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
125116.234375 70.305 9E03 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0
Attitude Records: 104691
Attitude Steps: 64
Maneuver ACM time: 39165.1 sec
Pointed ACM time: 85952.4 sec
-> Calculating aspect point100 99 count=3 sum1=38.019 sum2=358.719 sum3=57.73 100 100 count=549 sum1=6954.02 sum2=65651.2 sum3=10551.6 100 101 count=760 sum1=9626.16 sum2=90885.6 sum3=14617.6 101 97 count=1 sum1=12.683 sum2=119.555 sum3=19.251 101 98 count=2 sum1=25.358 sum2=239.122 sum3=38.499 101 99 count=2 sum1=25.352 sum2=239.135 sum3=38.487 102 95 count=1 sum1=12.693 sum2=119.535 sum3=19.265 102 96 count=3 sum1=38.069 sum2=358.625 sum3=57.776 102 97 count=2 sum1=25.372 sum2=239.099 sum3=38.501 103 94 count=2 sum1=25.404 sum2=239.037 sum3=38.533 103 95 count=2 sum1=25.394 sum2=239.057 sum3=38.528 104 92 count=2 sum1=25.42 sum2=239.006 sum3=38.56 104 93 count=2 sum1=25.412 sum2=239.02 sum3=38.55 105 90 count=2 sum1=25.444 sum2=238.962 sum3=38.577 105 91 count=2 sum1=25.434 sum2=238.98 sum3=38.558 105 92 count=1 sum1=12.714 sum2=119.496 sum3=19.282 106 88 count=2 sum1=25.463 sum2=238.924 sum3=38.595 106 89 count=2 sum1=25.456 sum2=238.94 sum3=38.59 106 90 count=1 sum1=12.725 sum2=119.476 sum3=19.293 107 86 count=2 sum1=25.485 sum2=238.881 sum3=38.615 107 87 count=3 sum1=38.214 sum2=358.348 sum3=57.909 107 88 count=1 sum1=12.734 sum2=119.456 sum3=19.299 108 84 count=3 sum1=38.257 sum2=358.266 sum3=57.948 108 85 count=3 sum1=38.241 sum2=358.295 sum3=57.933 109 82 count=3 sum1=38.288 sum2=358.204 sum3=57.977 109 83 count=3 sum1=38.275 sum2=358.23 sum3=57.964 109 84 count=1 sum1=12.755 sum2=119.416 sum3=19.319 110 80 count=3 sum1=38.319 sum2=358.144 sum3=58.002 110 81 count=4 sum1=51.075 sum2=477.56 sum3=77.322 110 82 count=1 sum1=12.765 sum2=119.396 sum3=19.328 111 78 count=3 sum1=38.346 sum2=358.089 sum3=58.026 111 79 count=5 sum1=63.894 sum2=596.855 sum3=96.696 111 80 count=1 sum1=12.775 sum2=119.377 sum3=19.336 112 65 count=1 sum1=12.793 sum2=119.234 sum3=19.33 112 76 count=3 sum1=38.376 sum2=358.031 sum3=58.05 112 77 count=6 sum1=76.734 sum2=716.101 sum3=116.088 112 78 count=3 sum1=38.355 sum2=358.073 sum3=58.034 113 74 count=4 sum1=51.208 sum2=477.294 sum3=77.433 113 75 count=10 sum1=127.994 sum2=1193.3 sum3=193.575 113 76 count=5 sum1=63.975 sum2=596.692 sum3=96.769 114 71 count=3962 sum1=50764.8 sum2=472635 sum3=76741.8 114 72 count=8 sum1=102.502 sum2=954.435 sum3=154.949 114 73 count=20 sum1=256.186 sum2=2386.2 sum3=387.302 114 74 count=9 sum1=115.245 sum2=1073.87 sum3=174.254 115 71 count=98597 sum1=1.26354e+06 sum2=1.17618e+07 sum3=1.91006e+06 115 72 count=38 sum1=486.993 sum2=4533.35 sum3=736.068 116 71 count=647 sum1=8297.97 sum2=77180.1 sum3=12536.3 1 out of 104691 points outside bin structure-> Euler angles: 12.8152, 119.292, 19.3723
Interpolating 6 records in time interval 141870623.839 - 141870627.838 Interpolating 110 records in time interval 141870627.838 - 141870643.838
607.998 second gap between superframes 535 and 536 Dropping SF 1780 with synch code word 0 = 191 not 250 607.998 second gap between superframes 2330 and 2331 575.998 second gap between superframes 4298 and 4299 607.998 second gap between superframes 6212 and 6213 Dropping SF 7874 with inconsistent datamode 0/31 Dropping SF 7918 with corrupted frame indicator Dropping SF 8121 with invalid bit rate 7 639.998 second gap between superframes 8180 and 8181 Dropping SF 8905 with corrupted frame indicator Dropping SF 8945 with inconsistent datamode 0/31 Dropping SF 9569 with inconsistent datamode 0/31 607.998 second gap between superframes 10092 and 10093 609.998 second gap between superframes 12037 and 12038 609.998 second gap between superframes 13942 and 13943 607.998 second gap between superframes 15861 and 15862 97.9997 second gap between superframes 17752 and 17753 Warning: GIS2 bit assignment changed between 141826559.35002 and 141826561.35001 Warning: GIS3 bit assignment changed between 141826573.34998 and 141826575.34997 Warning: GIS2 bit assignment changed between 141826583.34995 and 141826585.34994 Warning: GIS3 bit assignment changed between 141826599.3499 and 141826601.34989 GIS3 coordinate error time=141826982.19739 x=0 y=0 pha=832 rise=0 Dropping SF 18106 with invalid bit rate 7 39.9997 second gap between superframes 20113 and 20114 GIS2 coordinate error time=141838431.43662 x=0 y=0 pha=512 rise=0 SIS0 peak error time=141838423.18955 x=294 y=116 ph0=46 ph1=1286 ph2=2545 SIS0 peak error time=141838423.18955 x=162 y=58 ph0=140 ph1=3497 ph2=763 ph3=1436 SIS0 peak error time=141838423.18955 x=20 y=92 ph0=185 ph1=1316 ph2=1385 ph3=573 SIS0 peak error time=141838423.18955 x=160 y=113 ph0=80 ph1=2662 ph2=1208 ph3=230 SIS0 peak error time=141838423.18955 x=264 y=145 ph0=118 ph2=1941 ph3=991 ph4=789 ph5=1145 ph6=570 ph7=3883 Warning: GIS2 bit assignment changed between 141838689.31378 and 141838691.31378 Warning: GIS3 bit assignment changed between 141838701.31375 and 141838703.31374 Warning: GIS2 bit assignment changed between 141838711.31372 and 141838713.31371 Warning: GIS3 bit assignment changed between 141838725.31368 and 141838727.31367 Dropping SF 20483 with invalid bit rate 7 Dropping SF 22406 with synch code word 0 = 122 not 250 Dropping SF 22752 with inconsistent datamode 0/31 Dropping SF 22753 with corrupted frame indicator Dropping SF 22754 with inconsistent datamode 0/31 Dropping SF 23384 which overlaps by 0.001136 seconds Dropping SF 23386 which overlaps by 0.001136 seconds Dropping SF 23388 which overlaps by 0.00113595 seconds Dropping SF 23390 which overlaps by 0.0011355 seconds Dropping SF 23392 which overlaps by 0.0011355 seconds Dropping SF 23394 which overlaps by 0.00113526 seconds Dropping SF 23396 which overlaps by 0.00113523 seconds Dropping SF 23398 which overlaps by 0.00113517 seconds Dropping SF 23400 which overlaps by 0.00113446 seconds Dropping SF 23402 which overlaps by 0.00113493 seconds Dropping SF 23404 which overlaps by 0.00113496 seconds Dropping SF 23406 which overlaps by 0.00113457 seconds Dropping SF 23408 which overlaps by 0.00113454 seconds Dropping SF 23410 which overlaps by 0.00113472 seconds Dropping SF 23412 which overlaps by 0.00113475 seconds Dropping SF 23414 which overlaps by 0.0011346 seconds Dropping SF 23416 which overlaps by 0.0011346 seconds Dropping SF 23418 which overlaps by 0.00113457 seconds Dropping SF 23420 which overlaps by 0.00113457 seconds Dropping SF 23422 which overlaps by 0.0011346 seconds Dropping SF 23424 which overlaps by 0.0011346 seconds Dropping SF 23426 which overlaps by 0.0011346 seconds Dropping SF 24375 which overlaps by 0.0011355 seconds Dropping SF 24377 which overlaps by 0.00113529 seconds GIS2 coordinate error time=141853986.41556 x=0 y=0 pha=384 rise=0 Dropping SF 24379 which overlaps by 0.00113526 seconds Dropping SF 24381 which overlaps by 0.00113523 seconds Dropping SF 24383 which overlaps by 0.00113446 seconds Dropping SF 24385 which overlaps by 0.0011346 seconds Dropping SF 24387 which overlaps by 0.00113493 seconds Dropping SF 24389 which overlaps by 0.00113457 seconds Dropping SF 24391 which overlaps by 0.00113454 seconds Dropping SF 24393 which overlaps by 0.00113457 seconds Dropping SF 24395 which overlaps by 0.0011346 seconds Dropping SF 24397 which overlaps by 0.0011346 seconds Dropping SF 24399 which overlaps by 0.0011346 seconds SIS0 coordinate error time=141855974.97328 x=0 y=192 pha=0 grade=0 SIS0 coordinate error time=141855982.973 x=12 y=0 pha=0 grade=0 GIS2 coordinate error time=141856071.82314 x=0 y=0 pha=48 rise=0 SIS1 coordinate error time=141856082.97129 x=6 y=0 pha=0 grade=0 SIS0 coordinate error time=141856114.97073 x=0 y=0 pha=0 grade=3 SIS0 coordinate error time=141856146.97016 x=48 y=0 pha=0 grade=0 Dropping SF 24416 with synch code word 1 = 242 not 243 SIS0 coordinate error time=141856230.96874 x=305 y=426 pha=119 grade=0 Dropping SF 25460 which overlaps by 0.0011355 seconds Dropping SF 25462 which overlaps by 0.00113529 seconds Dropping SF 25464 which overlaps by 0.00113526 seconds Dropping SF 25466 which overlaps by 0.00113523 seconds Dropping SF 25468 which overlaps by 0.00113463 seconds Dropping SF 25470 which overlaps by 0.00113443 seconds Dropping SF 25472 which overlaps by 0.00113493 seconds Dropping SF 25474 which overlaps by 0.00113496 seconds Dropping SF 25476 which overlaps by 0.00113457 seconds Dropping SF 25478 which overlaps by 0.00113454 seconds Dropping SF 25480 which overlaps by 0.00113454 seconds Dropping SF 25482 which overlaps by 0.00113472 seconds Dropping SF 25484 which overlaps by 0.00113475 seconds Dropping SF 25486 which overlaps by 0.00113472 seconds Dropping SF 25488 which overlaps by 0.00113475 seconds Dropping SF 25490 which overlaps by 0.00113475 seconds Dropping SF 25492 which overlaps by 0.00113475 seconds Dropping SF 25494 which overlaps by 0.00113475 seconds Dropping SF 25495 with inconsistent datamode 0/31 Dropping SF 25991 which overlaps by 0.00113565 seconds Dropping SF 25993 which overlaps by 0.0011355 seconds Dropping SF 25995 which overlaps by 0.00113529 seconds Dropping SF 25997 which overlaps by 0.00113529 seconds Dropping SF 25999 which overlaps by 0.00113526 seconds Dropping SF 26001 which overlaps by 0.00113466 seconds Dropping SF 26003 which overlaps by 0.00113446 seconds Dropping SF 26005 which overlaps by 0.0011349 seconds Dropping SF 26007 which overlaps by 0.00113493 seconds Dropping SF 26009 which overlaps by 0.0011346 seconds Dropping SF 26011 which overlaps by 0.00113457 seconds Dropping SF 26013 which overlaps by 0.00113454 seconds Dropping SF 26015 which overlaps by 0.00113454 seconds Dropping SF 26017 which overlaps by 0.00113457 seconds Dropping SF 26019 which overlaps by 0.00113454 seconds Dropping SF 26021 which overlaps by 0.00113454 seconds Dropping SF 26023 which overlaps by 0.00113454 seconds Dropping SF 26025 which overlaps by 0.00113457 seconds 26138 of 26224 super frames processed-> Removing the following files with NEVENTS=0
ft970629_1345_0030G200670H.fits[0] ft970629_1345_0030G200770H.fits[0] ft970629_1345_0030G200870L.fits[0] ft970629_1345_0030G200970L.fits[0] ft970629_1345_0030G202070H.fits[0] ft970629_1345_0030G202170H.fits[0] ft970629_1345_0030G202270M.fits[0] ft970629_1345_0030G202370M.fits[0] ft970629_1345_0030G202470L.fits[0] ft970629_1345_0030G202570L.fits[0] ft970629_1345_0030G203770H.fits[0] ft970629_1345_0030G204670H.fits[0] ft970629_1345_0030G204870H.fits[0] ft970629_1345_0030G204970H.fits[0] ft970629_1345_0030G205070M.fits[0] ft970629_1345_0030G205170M.fits[0] ft970629_1345_0030G205270L.fits[0] ft970629_1345_0030G206070H.fits[0] ft970629_1345_0030G207470H.fits[0] ft970629_1345_0030G207570H.fits[0] ft970629_1345_0030G208270H.fits[0] ft970629_1345_0030G208970H.fits[0] ft970629_1345_0030G209770H.fits[0] ft970629_1345_0030G209870H.fits[0] ft970629_1345_0030G210970H.fits[0] ft970629_1345_0030G211070H.fits[0] ft970629_1345_0030G211170M.fits[0] ft970629_1345_0030G211270M.fits[0] ft970629_1345_0030G211370H.fits[0] ft970629_1345_0030G211470H.fits[0] ft970629_1345_0030G211570H.fits[0] ft970629_1345_0030G211670H.fits[0] ft970629_1345_0030G212370H.fits[0] ft970629_1345_0030G212770H.fits[0] ft970629_1345_0030G212870H.fits[0] ft970629_1345_0030G212970M.fits[0] ft970629_1345_0030G213070M.fits[0] ft970629_1345_0030G213170H.fits[0] ft970629_1345_0030G213270H.fits[0] ft970629_1345_0030G213370H.fits[0] ft970629_1345_0030G213470H.fits[0] ft970629_1345_0030G213570H.fits[0] ft970629_1345_0030G214570H.fits[0] ft970629_1345_0030G214670H.fits[0] ft970629_1345_0030G214770M.fits[0] ft970629_1345_0030G214870M.fits[0] ft970629_1345_0030G215570H.fits[0] ft970629_1345_0030G215670H.fits[0] ft970629_1345_0030G215770M.fits[0] ft970629_1345_0030G215870M.fits[0] ft970629_1345_0030G216470H.fits[0] ft970629_1345_0030G216570H.fits[0] ft970629_1345_0030G216670H.fits[0] ft970629_1345_0030G216770H.fits[0] ft970629_1345_0030G217970H.fits[0] ft970629_1345_0030G218070L.fits[0] ft970629_1345_0030G218870H.fits[0] ft970629_1345_0030G218970L.fits[0] ft970629_1345_0030G219070L.fits[0] ft970629_1345_0030G219570H.fits[0] ft970629_1345_0030G219670H.fits[0] ft970629_1345_0030G219770H.fits[0] ft970629_1345_0030G220270H.fits[0] ft970629_1345_0030G220370H.fits[0] ft970629_1345_0030G220470M.fits[0] ft970629_1345_0030G220570M.fits[0] ft970629_1345_0030G220670H.fits[0] ft970629_1345_0030G220770H.fits[0] ft970629_1345_0030G220870H.fits[0] ft970629_1345_0030G220970H.fits[0] ft970629_1345_0030G221070H.fits[0] ft970629_1345_0030G222370M.fits[0] ft970629_1345_0030G222470L.fits[0] ft970629_1345_0030G222570L.fits[0] ft970629_1345_0030G222870H.fits[0] ft970629_1345_0030G223470M.fits[0] ft970629_1345_0030G223570L.fits[0] ft970629_1345_0030G223670L.fits[0] ft970629_1345_0030G225270H.fits[0] ft970629_1345_0030G300670H.fits[0] ft970629_1345_0030G300770H.fits[0] ft970629_1345_0030G300870L.fits[0] ft970629_1345_0030G300970L.fits[0] ft970629_1345_0030G301770H.fits[0] ft970629_1345_0030G302170H.fits[0] ft970629_1345_0030G302270M.fits[0] ft970629_1345_0030G302370M.fits[0] ft970629_1345_0030G302470L.fits[0] ft970629_1345_0030G302570L.fits[0] ft970629_1345_0030G303670H.fits[0] ft970629_1345_0030G303770H.fits[0] ft970629_1345_0030G304470H.fits[0] ft970629_1345_0030G304870H.fits[0] ft970629_1345_0030G304970H.fits[0] ft970629_1345_0030G305070M.fits[0] ft970629_1345_0030G305170M.fits[0] ft970629_1345_0030G305270L.fits[0] ft970629_1345_0030G307370H.fits[0] ft970629_1345_0030G308270H.fits[0] ft970629_1345_0030G309770H.fits[0] ft970629_1345_0030G309870H.fits[0] ft970629_1345_0030G310170H.fits[0] ft970629_1345_0030G310770H.fits[0] ft970629_1345_0030G310970H.fits[0] ft970629_1345_0030G311070H.fits[0] ft970629_1345_0030G311170M.fits[0] ft970629_1345_0030G311270M.fits[0] ft970629_1345_0030G311370H.fits[0] ft970629_1345_0030G311470H.fits[0] ft970629_1345_0030G311570H.fits[0] ft970629_1345_0030G311670H.fits[0] ft970629_1345_0030G311970H.fits[0] ft970629_1345_0030G312370H.fits[0] ft970629_1345_0030G312570H.fits[0] ft970629_1345_0030G312770H.fits[0] ft970629_1345_0030G312870H.fits[0] ft970629_1345_0030G312970M.fits[0] ft970629_1345_0030G313070M.fits[0] ft970629_1345_0030G313170H.fits[0] ft970629_1345_0030G313270H.fits[0] ft970629_1345_0030G313370H.fits[0] ft970629_1345_0030G313470H.fits[0] ft970629_1345_0030G313570H.fits[0] ft970629_1345_0030G314170H.fits[0] ft970629_1345_0030G314570H.fits[0] ft970629_1345_0030G314670H.fits[0] ft970629_1345_0030G314770M.fits[0] ft970629_1345_0030G314870M.fits[0] ft970629_1345_0030G315570H.fits[0] ft970629_1345_0030G315670H.fits[0] ft970629_1345_0030G315770M.fits[0] ft970629_1345_0030G315870M.fits[0] ft970629_1345_0030G316570H.fits[0] ft970629_1345_0030G316670H.fits[0] ft970629_1345_0030G316770H.fits[0] ft970629_1345_0030G316870H.fits[0] ft970629_1345_0030G317470H.fits[0] ft970629_1345_0030G317670H.fits[0] ft970629_1345_0030G317870H.fits[0] ft970629_1345_0030G317970H.fits[0] ft970629_1345_0030G318070L.fits[0] ft970629_1345_0030G318870H.fits[0] ft970629_1345_0030G318970L.fits[0] ft970629_1345_0030G319070L.fits[0] ft970629_1345_0030G319770H.fits[0] ft970629_1345_0030G319870H.fits[0] ft970629_1345_0030G320470H.fits[0] ft970629_1345_0030G320570M.fits[0] ft970629_1345_0030G320670M.fits[0] ft970629_1345_0030G320770H.fits[0] ft970629_1345_0030G320870H.fits[0] ft970629_1345_0030G320970H.fits[0] ft970629_1345_0030G321070H.fits[0] ft970629_1345_0030G321270H.fits[0] ft970629_1345_0030G321370H.fits[0] ft970629_1345_0030G321870H.fits[0] ft970629_1345_0030G321970H.fits[0] ft970629_1345_0030G322070H.fits[0] ft970629_1345_0030G322470M.fits[0] ft970629_1345_0030G322570L.fits[0] ft970629_1345_0030G322670L.fits[0] ft970629_1345_0030G322970H.fits[0] ft970629_1345_0030G323570M.fits[0] ft970629_1345_0030G323670L.fits[0] ft970629_1345_0030G323770L.fits[0] ft970629_1345_0030G324370H.fits[0] ft970629_1345_0030G324470H.fits[0] ft970629_1345_0030G324570H.fits[0] ft970629_1345_0030S000602H.fits[0] ft970629_1345_0030S000702L.fits[0] ft970629_1345_0030S000802L.fits[0] ft970629_1345_0030S001402M.fits[0] ft970629_1345_0030S001502L.fits[0] ft970629_1345_0030S001602L.fits[0] ft970629_1345_0030S002102H.fits[0] ft970629_1345_0030S002202L.fits[0] ft970629_1345_0030S005602M.fits[0] ft970629_1345_0030S006502M.fits[0] ft970629_1345_0030S006902M.fits[0] ft970629_1345_0030S007302M.fits[0] ft970629_1345_0030S007702M.fits[0] ft970629_1345_0030S008302M.fits[0] ft970629_1345_0030S008402M.fits[0] ft970629_1345_0030S009202L.fits[0] ft970629_1345_0030S009302L.fits[0] ft970629_1345_0030S010002L.fits[0] ft970629_1345_0030S010102L.fits[0] ft970629_1345_0030S010802M.fits[0] ft970629_1345_0030S010902M.fits[0] ft970629_1345_0030S011602L.fits[0] ft970629_1345_0030S100602H.fits[0] ft970629_1345_0030S100702L.fits[0] ft970629_1345_0030S101202M.fits[0] ft970629_1345_0030S101302L.fits[0] ft970629_1345_0030S101702H.fits[0] ft970629_1345_0030S101802L.fits[0] ft970629_1345_0030S103902M.fits[0] ft970629_1345_0030S104502M.fits[0] ft970629_1345_0030S104802M.fits[0] ft970629_1345_0030S105102M.fits[0] ft970629_1345_0030S105402M.fits[0] ft970629_1345_0030S105802M.fits[0] ft970629_1345_0030S106502L.fits[0] ft970629_1345_0030S107702M.fits[0] ft970629_1345_0030S108302L.fits[0]-> Checking for empty GTI extensions
ft970629_1345_0030S000101H.fits[2] ft970629_1345_0030S000202M.fits[2] ft970629_1345_0030S000302L.fits[2] ft970629_1345_0030S000401L.fits[2] ft970629_1345_0030S000501H.fits[2] ft970629_1345_0030S000902L.fits[2] ft970629_1345_0030S001002L.fits[2] ft970629_1345_0030S001102M.fits[2] ft970629_1345_0030S001201H.fits[2] ft970629_1345_0030S001302M.fits[2] ft970629_1345_0030S001702L.fits[2] ft970629_1345_0030S001802L.fits[2] ft970629_1345_0030S001902M.fits[2] ft970629_1345_0030S002001H.fits[2] ft970629_1345_0030S002302L.fits[2] ft970629_1345_0030S002402L.fits[2] ft970629_1345_0030S002502M.fits[2] ft970629_1345_0030S002601H.fits[2] ft970629_1345_0030S002701H.fits[2] ft970629_1345_0030S002802M.fits[2] ft970629_1345_0030S002902L.fits[2] ft970629_1345_0030S003002L.fits[2] ft970629_1345_0030S003102M.fits[2] ft970629_1345_0030S003201H.fits[2] ft970629_1345_0030S003302M.fits[2] ft970629_1345_0030S003402M.fits[2] ft970629_1345_0030S003502L.fits[2] ft970629_1345_0030S003602L.fits[2] ft970629_1345_0030S003701H.fits[2] ft970629_1345_0030S003801H.fits[2] ft970629_1345_0030S003902M.fits[2] ft970629_1345_0030S004002M.fits[2] ft970629_1345_0030S004101H.fits[2] ft970629_1345_0030S004202M.fits[2] ft970629_1345_0030S004302M.fits[2] ft970629_1345_0030S004402L.fits[2] ft970629_1345_0030S004502L.fits[2] ft970629_1345_0030S004602M.fits[2] ft970629_1345_0030S004701H.fits[2] ft970629_1345_0030S004801H.fits[2] ft970629_1345_0030S004902H.fits[2] ft970629_1345_0030S005002L.fits[2] ft970629_1345_0030S005102L.fits[2] ft970629_1345_0030S005201H.fits[2] ft970629_1345_0030S005301H.fits[2] ft970629_1345_0030S005402M.fits[2] ft970629_1345_0030S005502M.fits[2] ft970629_1345_0030S005701H.fits[2] ft970629_1345_0030S005801H.fits[2] ft970629_1345_0030S005902M.fits[2] ft970629_1345_0030S006002M.fits[2] ft970629_1345_0030S006101H.fits[2] ft970629_1345_0030S006202M.fits[2] ft970629_1345_0030S006301H.fits[2] ft970629_1345_0030S006401H.fits[2] ft970629_1345_0030S006601H.fits[2] ft970629_1345_0030S006701H.fits[2] ft970629_1345_0030S006801H.fits[2] ft970629_1345_0030S007002M.fits[2] ft970629_1345_0030S007101H.fits[2] ft970629_1345_0030S007201H.fits[2] ft970629_1345_0030S007401H.fits[2] ft970629_1345_0030S007501H.fits[2] ft970629_1345_0030S007601H.fits[2] ft970629_1345_0030S007802M.fits[2] ft970629_1345_0030S007902M.fits[2] ft970629_1345_0030S008002M.fits[2] ft970629_1345_0030S008101H.fits[2] ft970629_1345_0030S008201H.fits[2] ft970629_1345_0030S008502M.fits[2] ft970629_1345_0030S008602M.fits[2] ft970629_1345_0030S008701H.fits[2] ft970629_1345_0030S008802M.fits[2] ft970629_1345_0030S008901H.fits[2] ft970629_1345_0030S009002H.fits[2] ft970629_1345_0030S009102L.fits[2] ft970629_1345_0030S009402L.fits[2] ft970629_1345_0030S009502L.fits[2] ft970629_1345_0030S009601L.fits[2] ft970629_1345_0030S009701H.fits[2] ft970629_1345_0030S009802H.fits[2] ft970629_1345_0030S009902L.fits[2] ft970629_1345_0030S010202L.fits[2] ft970629_1345_0030S010302L.fits[2] ft970629_1345_0030S010401L.fits[2] ft970629_1345_0030S010501H.fits[2] ft970629_1345_0030S010602M.fits[2] ft970629_1345_0030S010702M.fits[2] ft970629_1345_0030S011001H.fits[2] ft970629_1345_0030S011101H.fits[2] ft970629_1345_0030S011202M.fits[2] ft970629_1345_0030S011301H.fits[2] ft970629_1345_0030S011402M.fits[2] ft970629_1345_0030S011502L.fits[2] ft970629_1345_0030S011702L.fits[2] ft970629_1345_0030S011802L.fits[2] ft970629_1345_0030S011902M.fits[2] ft970629_1345_0030S012001H.fits[2] ft970629_1345_0030S012102M.fits[2] ft970629_1345_0030S012202M.fits[2] ft970629_1345_0030S012302L.fits[2] ft970629_1345_0030S012402L.fits[2] ft970629_1345_0030S012502M.fits[2] ft970629_1345_0030S012601H.fits[2] ft970629_1345_0030S012702M.fits[2] ft970629_1345_0030S012802M.fits[2] ft970629_1345_0030S012902L.fits[2] ft970629_1345_0030S013002L.fits[2] ft970629_1345_0030S013102M.fits[2] ft970629_1345_0030S013201H.fits[2] ft970629_1345_0030S013302M.fits[2] ft970629_1345_0030S013402M.fits[2] ft970629_1345_0030S013502M.fits[2] ft970629_1345_0030S013602M.fits[2] ft970629_1345_0030S013702L.fits[2] ft970629_1345_0030S013802L.fits[2] ft970629_1345_0030S013902M.fits[2] ft970629_1345_0030S014002M.fits[2]-> Merging GTIs from the following files:
ft970629_1345_0030S100101H.fits[2] ft970629_1345_0030S100202M.fits[2] ft970629_1345_0030S100302L.fits[2] ft970629_1345_0030S100401L.fits[2] ft970629_1345_0030S100501H.fits[2] ft970629_1345_0030S100802L.fits[2] ft970629_1345_0030S100902M.fits[2] ft970629_1345_0030S101001H.fits[2] ft970629_1345_0030S101102M.fits[2] ft970629_1345_0030S101402L.fits[2] ft970629_1345_0030S101502M.fits[2] ft970629_1345_0030S101601H.fits[2] ft970629_1345_0030S101902L.fits[2] ft970629_1345_0030S102002M.fits[2] ft970629_1345_0030S102101H.fits[2] ft970629_1345_0030S102202M.fits[2] ft970629_1345_0030S102302L.fits[2] ft970629_1345_0030S102402M.fits[2] ft970629_1345_0030S102501H.fits[2] ft970629_1345_0030S102602M.fits[2] ft970629_1345_0030S102702L.fits[2] ft970629_1345_0030S102801H.fits[2] ft970629_1345_0030S102902M.fits[2] ft970629_1345_0030S103001H.fits[2] ft970629_1345_0030S103102M.fits[2] ft970629_1345_0030S103202L.fits[2] ft970629_1345_0030S103302M.fits[2] ft970629_1345_0030S103401H.fits[2] ft970629_1345_0030S103502H.fits[2] ft970629_1345_0030S103602L.fits[2] ft970629_1345_0030S103701H.fits[2] ft970629_1345_0030S103802M.fits[2] ft970629_1345_0030S104001H.fits[2] ft970629_1345_0030S104102M.fits[2] ft970629_1345_0030S104201H.fits[2] ft970629_1345_0030S104302M.fits[2] ft970629_1345_0030S104401H.fits[2] ft970629_1345_0030S104601H.fits[2] ft970629_1345_0030S104701H.fits[2] ft970629_1345_0030S104902M.fits[2] ft970629_1345_0030S105001H.fits[2] ft970629_1345_0030S105201H.fits[2] ft970629_1345_0030S105301H.fits[2] ft970629_1345_0030S105502M.fits[2] ft970629_1345_0030S105601H.fits[2] ft970629_1345_0030S105701H.fits[2] ft970629_1345_0030S105902M.fits[2] ft970629_1345_0030S106001H.fits[2] ft970629_1345_0030S106102M.fits[2] ft970629_1345_0030S106201H.fits[2] ft970629_1345_0030S106302H.fits[2] ft970629_1345_0030S106402L.fits[2] ft970629_1345_0030S106602L.fits[2] ft970629_1345_0030S106701L.fits[2] ft970629_1345_0030S106801H.fits[2] ft970629_1345_0030S106902H.fits[2] ft970629_1345_0030S107002L.fits[2] ft970629_1345_0030S107102L.fits[2] ft970629_1345_0030S107202L.fits[2] ft970629_1345_0030S107301L.fits[2] ft970629_1345_0030S107401H.fits[2] ft970629_1345_0030S107502M.fits[2] ft970629_1345_0030S107602M.fits[2] ft970629_1345_0030S107801H.fits[2] ft970629_1345_0030S107902M.fits[2] ft970629_1345_0030S108001H.fits[2] ft970629_1345_0030S108102M.fits[2] ft970629_1345_0030S108202L.fits[2] ft970629_1345_0030S108402L.fits[2] ft970629_1345_0030S108502M.fits[2] ft970629_1345_0030S108601H.fits[2] ft970629_1345_0030S108702M.fits[2] ft970629_1345_0030S108802L.fits[2] ft970629_1345_0030S108902M.fits[2] ft970629_1345_0030S109001H.fits[2] ft970629_1345_0030S109102M.fits[2] ft970629_1345_0030S109202L.fits[2] ft970629_1345_0030S109302M.fits[2] ft970629_1345_0030S109401H.fits[2] ft970629_1345_0030S109502M.fits[2] ft970629_1345_0030S109602M.fits[2] ft970629_1345_0030S109702M.fits[2] ft970629_1345_0030S109802L.fits[2] ft970629_1345_0030S109902M.fits[2]-> Merging GTIs from the following files:
ft970629_1345_0030G200170H.fits[2] ft970629_1345_0030G200270M.fits[2] ft970629_1345_0030G200370M.fits[2] ft970629_1345_0030G200470L.fits[2] ft970629_1345_0030G200570H.fits[2] ft970629_1345_0030G201070L.fits[2] ft970629_1345_0030G201170L.fits[2] ft970629_1345_0030G201270M.fits[2] ft970629_1345_0030G201370M.fits[2] ft970629_1345_0030G201470M.fits[2] ft970629_1345_0030G201570M.fits[2] ft970629_1345_0030G201670H.fits[2] ft970629_1345_0030G201770H.fits[2] ft970629_1345_0030G201870H.fits[2] ft970629_1345_0030G201970H.fits[2] ft970629_1345_0030G202670L.fits[2] ft970629_1345_0030G202770L.fits[2] ft970629_1345_0030G202870M.fits[2] ft970629_1345_0030G202970M.fits[2] ft970629_1345_0030G203070M.fits[2] ft970629_1345_0030G203170M.fits[2] ft970629_1345_0030G203270H.fits[2] ft970629_1345_0030G203370H.fits[2] ft970629_1345_0030G203470H.fits[2] ft970629_1345_0030G203570H.fits[2] ft970629_1345_0030G203670H.fits[2] ft970629_1345_0030G203870L.fits[2] ft970629_1345_0030G203970L.fits[2] ft970629_1345_0030G204070M.fits[2] ft970629_1345_0030G204170M.fits[2] ft970629_1345_0030G204270M.fits[2] ft970629_1345_0030G204370M.fits[2] ft970629_1345_0030G204470H.fits[2] ft970629_1345_0030G204570H.fits[2] ft970629_1345_0030G204770H.fits[2] ft970629_1345_0030G205370L.fits[2] ft970629_1345_0030G205470L.fits[2] ft970629_1345_0030G205570M.fits[2] ft970629_1345_0030G205670M.fits[2] ft970629_1345_0030G205770M.fits[2] ft970629_1345_0030G205870M.fits[2] ft970629_1345_0030G205970H.fits[2] ft970629_1345_0030G206170H.fits[2] ft970629_1345_0030G206270H.fits[2] ft970629_1345_0030G206370M.fits[2] ft970629_1345_0030G206470M.fits[2] ft970629_1345_0030G206570L.fits[2] ft970629_1345_0030G206670L.fits[2] ft970629_1345_0030G206770H.fits[2] ft970629_1345_0030G206870H.fits[2] ft970629_1345_0030G206970H.fits[2] ft970629_1345_0030G207070H.fits[2] ft970629_1345_0030G207170M.fits[2] ft970629_1345_0030G207270M.fits[2] ft970629_1345_0030G207370H.fits[2] ft970629_1345_0030G207670H.fits[2] ft970629_1345_0030G207770M.fits[2] ft970629_1345_0030G207870M.fits[2] ft970629_1345_0030G207970L.fits[2] ft970629_1345_0030G208070M.fits[2] ft970629_1345_0030G208170H.fits[2] ft970629_1345_0030G208370H.fits[2] ft970629_1345_0030G208470H.fits[2] ft970629_1345_0030G208570L.fits[2] ft970629_1345_0030G208670L.fits[2] ft970629_1345_0030G208770H.fits[2] ft970629_1345_0030G208870H.fits[2] ft970629_1345_0030G209070H.fits[2] ft970629_1345_0030G209170M.fits[2] ft970629_1345_0030G209270M.fits[2] ft970629_1345_0030G209370H.fits[2] ft970629_1345_0030G209470H.fits[2] ft970629_1345_0030G209570H.fits[2] ft970629_1345_0030G209670H.fits[2] ft970629_1345_0030G209970H.fits[2] ft970629_1345_0030G210070H.fits[2] ft970629_1345_0030G210170H.fits[2] ft970629_1345_0030G210270H.fits[2] ft970629_1345_0030G210370M.fits[2] ft970629_1345_0030G210470M.fits[2] ft970629_1345_0030G210570H.fits[2] ft970629_1345_0030G210670H.fits[2] ft970629_1345_0030G210770H.fits[2] ft970629_1345_0030G210870H.fits[2] ft970629_1345_0030G211770H.fits[2] ft970629_1345_0030G211870H.fits[2] ft970629_1345_0030G211970H.fits[2] ft970629_1345_0030G212070H.fits[2] ft970629_1345_0030G212170M.fits[2] ft970629_1345_0030G212270M.fits[2] ft970629_1345_0030G212470H.fits[2] ft970629_1345_0030G212570H.fits[2] ft970629_1345_0030G212670H.fits[2] ft970629_1345_0030G213670H.fits[2] ft970629_1345_0030G213770H.fits[2] ft970629_1345_0030G213870H.fits[2] ft970629_1345_0030G213970M.fits[2] ft970629_1345_0030G214070M.fits[2] ft970629_1345_0030G214170H.fits[2] ft970629_1345_0030G214270H.fits[2] ft970629_1345_0030G214370H.fits[2] ft970629_1345_0030G214470H.fits[2] ft970629_1345_0030G214970M.fits[2] ft970629_1345_0030G215070M.fits[2] ft970629_1345_0030G215170H.fits[2] ft970629_1345_0030G215270H.fits[2] ft970629_1345_0030G215370H.fits[2] ft970629_1345_0030G215470H.fits[2] ft970629_1345_0030G215970M.fits[2] ft970629_1345_0030G216070M.fits[2] ft970629_1345_0030G216170H.fits[2] ft970629_1345_0030G216270H.fits[2] ft970629_1345_0030G216370H.fits[2] ft970629_1345_0030G216870H.fits[2] ft970629_1345_0030G216970H.fits[2] ft970629_1345_0030G217070H.fits[2] ft970629_1345_0030G217170H.fits[2] ft970629_1345_0030G217270M.fits[2] ft970629_1345_0030G217370M.fits[2] ft970629_1345_0030G217470H.fits[2] ft970629_1345_0030G217570H.fits[2] ft970629_1345_0030G217670H.fits[2] ft970629_1345_0030G217770H.fits[2] ft970629_1345_0030G217870H.fits[2] ft970629_1345_0030G218170L.fits[2] ft970629_1345_0030G218270L.fits[2] ft970629_1345_0030G218370H.fits[2] ft970629_1345_0030G218470H.fits[2] ft970629_1345_0030G218570H.fits[2] ft970629_1345_0030G218670H.fits[2] ft970629_1345_0030G218770H.fits[2] ft970629_1345_0030G219170L.fits[2] ft970629_1345_0030G219270L.fits[2] ft970629_1345_0030G219370H.fits[2] ft970629_1345_0030G219470H.fits[2] ft970629_1345_0030G219870H.fits[2] ft970629_1345_0030G219970H.fits[2] ft970629_1345_0030G220070H.fits[2] ft970629_1345_0030G220170H.fits[2] ft970629_1345_0030G221170H.fits[2] ft970629_1345_0030G221270H.fits[2] ft970629_1345_0030G221370H.fits[2] ft970629_1345_0030G221470H.fits[2] ft970629_1345_0030G221570M.fits[2] ft970629_1345_0030G221670M.fits[2] ft970629_1345_0030G221770H.fits[2] ft970629_1345_0030G221870H.fits[2] ft970629_1345_0030G221970H.fits[2] ft970629_1345_0030G222070H.fits[2] ft970629_1345_0030G222170M.fits[2] ft970629_1345_0030G222270M.fits[2] ft970629_1345_0030G222670L.fits[2] ft970629_1345_0030G222770M.fits[2] ft970629_1345_0030G222970H.fits[2] ft970629_1345_0030G223070H.fits[2] ft970629_1345_0030G223170H.fits[2] ft970629_1345_0030G223270M.fits[2] ft970629_1345_0030G223370M.fits[2] ft970629_1345_0030G223770L.fits[2] ft970629_1345_0030G223870L.fits[2] ft970629_1345_0030G223970M.fits[2] ft970629_1345_0030G224070H.fits[2] ft970629_1345_0030G224170H.fits[2] ft970629_1345_0030G224270H.fits[2] ft970629_1345_0030G224370H.fits[2] ft970629_1345_0030G224470H.fits[2] ft970629_1345_0030G224570H.fits[2] ft970629_1345_0030G224670M.fits[2] ft970629_1345_0030G224770M.fits[2] ft970629_1345_0030G224870L.fits[2] ft970629_1345_0030G224970L.fits[2] ft970629_1345_0030G225070M.fits[2] ft970629_1345_0030G225170H.fits[2] ft970629_1345_0030G225370H.fits[2] ft970629_1345_0030G225470H.fits[2] ft970629_1345_0030G225570M.fits[2] ft970629_1345_0030G225670M.fits[2] ft970629_1345_0030G225770L.fits[2] ft970629_1345_0030G225870M.fits[2]-> Merging GTIs from the following files:
ft970629_1345_0030G300170H.fits[2] ft970629_1345_0030G300270M.fits[2] ft970629_1345_0030G300370M.fits[2] ft970629_1345_0030G300470L.fits[2] ft970629_1345_0030G300570H.fits[2] ft970629_1345_0030G301070L.fits[2] ft970629_1345_0030G301170L.fits[2] ft970629_1345_0030G301270M.fits[2] ft970629_1345_0030G301370M.fits[2] ft970629_1345_0030G301470M.fits[2] ft970629_1345_0030G301570M.fits[2] ft970629_1345_0030G301670H.fits[2] ft970629_1345_0030G301870H.fits[2] ft970629_1345_0030G301970H.fits[2] ft970629_1345_0030G302070H.fits[2] ft970629_1345_0030G302670L.fits[2] ft970629_1345_0030G302770L.fits[2] ft970629_1345_0030G302870M.fits[2] ft970629_1345_0030G302970M.fits[2] ft970629_1345_0030G303070M.fits[2] ft970629_1345_0030G303170M.fits[2] ft970629_1345_0030G303270H.fits[2] ft970629_1345_0030G303370H.fits[2] ft970629_1345_0030G303470H.fits[2] ft970629_1345_0030G303570H.fits[2] ft970629_1345_0030G303870L.fits[2] ft970629_1345_0030G303970L.fits[2] ft970629_1345_0030G304070M.fits[2] ft970629_1345_0030G304170M.fits[2] ft970629_1345_0030G304270M.fits[2] ft970629_1345_0030G304370M.fits[2] ft970629_1345_0030G304570H.fits[2] ft970629_1345_0030G304670H.fits[2] ft970629_1345_0030G304770H.fits[2] ft970629_1345_0030G305370L.fits[2] ft970629_1345_0030G305470L.fits[2] ft970629_1345_0030G305570M.fits[2] ft970629_1345_0030G305670M.fits[2] ft970629_1345_0030G305770M.fits[2] ft970629_1345_0030G305870M.fits[2] ft970629_1345_0030G305970H.fits[2] ft970629_1345_0030G306070H.fits[2] ft970629_1345_0030G306170H.fits[2] ft970629_1345_0030G306270H.fits[2] ft970629_1345_0030G306370M.fits[2] ft970629_1345_0030G306470M.fits[2] ft970629_1345_0030G306570L.fits[2] ft970629_1345_0030G306670L.fits[2] ft970629_1345_0030G306770H.fits[2] ft970629_1345_0030G306870H.fits[2] ft970629_1345_0030G306970H.fits[2] ft970629_1345_0030G307070H.fits[2] ft970629_1345_0030G307170M.fits[2] ft970629_1345_0030G307270M.fits[2] ft970629_1345_0030G307470H.fits[2] ft970629_1345_0030G307570H.fits[2] ft970629_1345_0030G307670H.fits[2] ft970629_1345_0030G307770M.fits[2] ft970629_1345_0030G307870M.fits[2] ft970629_1345_0030G307970L.fits[2] ft970629_1345_0030G308070M.fits[2] ft970629_1345_0030G308170H.fits[2] ft970629_1345_0030G308370H.fits[2] ft970629_1345_0030G308470H.fits[2] ft970629_1345_0030G308570L.fits[2] ft970629_1345_0030G308670L.fits[2] ft970629_1345_0030G308770H.fits[2] ft970629_1345_0030G308870H.fits[2] ft970629_1345_0030G308970H.fits[2] ft970629_1345_0030G309070H.fits[2] ft970629_1345_0030G309170M.fits[2] ft970629_1345_0030G309270M.fits[2] ft970629_1345_0030G309370H.fits[2] ft970629_1345_0030G309470H.fits[2] ft970629_1345_0030G309570H.fits[2] ft970629_1345_0030G309670H.fits[2] ft970629_1345_0030G309970H.fits[2] ft970629_1345_0030G310070H.fits[2] ft970629_1345_0030G310270H.fits[2] ft970629_1345_0030G310370M.fits[2] ft970629_1345_0030G310470M.fits[2] ft970629_1345_0030G310570H.fits[2] ft970629_1345_0030G310670H.fits[2] ft970629_1345_0030G310870H.fits[2] ft970629_1345_0030G311770H.fits[2] ft970629_1345_0030G311870H.fits[2] ft970629_1345_0030G312070H.fits[2] ft970629_1345_0030G312170M.fits[2] ft970629_1345_0030G312270M.fits[2] ft970629_1345_0030G312470H.fits[2] ft970629_1345_0030G312670H.fits[2] ft970629_1345_0030G313670H.fits[2] ft970629_1345_0030G313770H.fits[2] ft970629_1345_0030G313870H.fits[2] ft970629_1345_0030G313970M.fits[2] ft970629_1345_0030G314070M.fits[2] ft970629_1345_0030G314270H.fits[2] ft970629_1345_0030G314370H.fits[2] ft970629_1345_0030G314470H.fits[2] ft970629_1345_0030G314970M.fits[2] ft970629_1345_0030G315070M.fits[2] ft970629_1345_0030G315170H.fits[2] ft970629_1345_0030G315270H.fits[2] ft970629_1345_0030G315370H.fits[2] ft970629_1345_0030G315470H.fits[2] ft970629_1345_0030G315970M.fits[2] ft970629_1345_0030G316070M.fits[2] ft970629_1345_0030G316170H.fits[2] ft970629_1345_0030G316270H.fits[2] ft970629_1345_0030G316370H.fits[2] ft970629_1345_0030G316470H.fits[2] ft970629_1345_0030G316970H.fits[2] ft970629_1345_0030G317070H.fits[2] ft970629_1345_0030G317170H.fits[2] ft970629_1345_0030G317270M.fits[2] ft970629_1345_0030G317370M.fits[2] ft970629_1345_0030G317570H.fits[2] ft970629_1345_0030G317770H.fits[2] ft970629_1345_0030G318170L.fits[2] ft970629_1345_0030G318270L.fits[2] ft970629_1345_0030G318370H.fits[2] ft970629_1345_0030G318470H.fits[2] ft970629_1345_0030G318570H.fits[2] ft970629_1345_0030G318670H.fits[2] ft970629_1345_0030G318770H.fits[2] ft970629_1345_0030G319170L.fits[2] ft970629_1345_0030G319270L.fits[2] ft970629_1345_0030G319370H.fits[2] ft970629_1345_0030G319470H.fits[2] ft970629_1345_0030G319570H.fits[2] ft970629_1345_0030G319670H.fits[2] ft970629_1345_0030G319970H.fits[2] ft970629_1345_0030G320070H.fits[2] ft970629_1345_0030G320170H.fits[2] ft970629_1345_0030G320270H.fits[2] ft970629_1345_0030G320370H.fits[2] ft970629_1345_0030G321170H.fits[2] ft970629_1345_0030G321470H.fits[2] ft970629_1345_0030G321570H.fits[2] ft970629_1345_0030G321670M.fits[2] ft970629_1345_0030G321770M.fits[2] ft970629_1345_0030G322170H.fits[2] ft970629_1345_0030G322270M.fits[2] ft970629_1345_0030G322370M.fits[2] ft970629_1345_0030G322770L.fits[2] ft970629_1345_0030G322870M.fits[2] ft970629_1345_0030G323070H.fits[2] ft970629_1345_0030G323170H.fits[2] ft970629_1345_0030G323270H.fits[2] ft970629_1345_0030G323370M.fits[2] ft970629_1345_0030G323470M.fits[2] ft970629_1345_0030G323870L.fits[2] ft970629_1345_0030G323970L.fits[2] ft970629_1345_0030G324070M.fits[2] ft970629_1345_0030G324170M.fits[2] ft970629_1345_0030G324270M.fits[2] ft970629_1345_0030G324670H.fits[2] ft970629_1345_0030G324770M.fits[2] ft970629_1345_0030G324870M.fits[2] ft970629_1345_0030G324970L.fits[2] ft970629_1345_0030G325070L.fits[2] ft970629_1345_0030G325170M.fits[2] ft970629_1345_0030G325270H.fits[2] ft970629_1345_0030G325370H.fits[2] ft970629_1345_0030G325470H.fits[2] ft970629_1345_0030G325570H.fits[2] ft970629_1345_0030G325670M.fits[2] ft970629_1345_0030G325770M.fits[2] ft970629_1345_0030G325870L.fits[2] ft970629_1345_0030G325970M.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 3 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g200470h.prelist merge count = 4 photon cnt = 8 GISSORTSPLIT:LO:g200570h.prelist merge count = 4 photon cnt = 9 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200770h.prelist merge count = 34 photon cnt = 33076 GISSORTSPLIT:LO:g200870h.prelist merge count = 16 photon cnt = 30 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g202170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g202370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g202470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g202570h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g202670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g202870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g202970h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g203070h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g203170h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g203270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g203370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g203470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g203570h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g203670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g203770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g203870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g203970h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g204070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g204170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g204270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g204370h.prelist merge count = 2 photon cnt = 21 GISSORTSPLIT:LO:g204470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 23 GISSORTSPLIT:LO:g200270l.prelist merge count = 5 photon cnt = 192 GISSORTSPLIT:LO:g200370l.prelist merge count = 14 photon cnt = 12310 GISSORTSPLIT:LO:g200470l.prelist merge count = 3 photon cnt = 258 GISSORTSPLIT:LO:g200170m.prelist merge count = 2 photon cnt = 12 GISSORTSPLIT:LO:g200270m.prelist merge count = 25 photon cnt = 21409 GISSORTSPLIT:LO:g200370m.prelist merge count = 18 photon cnt = 402 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200870m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200970m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g201070m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g201170m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:Total filenames split = 179 GISSORTSPLIT:LO:Total split file cnt = 59 GISSORTSPLIT:LO:End program-> Creating ad75071000g200170h.unf
---- cmerge: version 1.6 ---- A total of 34 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G200170H.fits 2 -- ft970629_1345_0030G200570H.fits 3 -- ft970629_1345_0030G201970H.fits 4 -- ft970629_1345_0030G203570H.fits 5 -- ft970629_1345_0030G204770H.fits 6 -- ft970629_1345_0030G206270H.fits 7 -- ft970629_1345_0030G207070H.fits 8 -- ft970629_1345_0030G207670H.fits 9 -- ft970629_1345_0030G208470H.fits 10 -- ft970629_1345_0030G209070H.fits 11 -- ft970629_1345_0030G209670H.fits 12 -- ft970629_1345_0030G210270H.fits 13 -- ft970629_1345_0030G210870H.fits 14 -- ft970629_1345_0030G212070H.fits 15 -- ft970629_1345_0030G212670H.fits 16 -- ft970629_1345_0030G213870H.fits 17 -- ft970629_1345_0030G214470H.fits 18 -- ft970629_1345_0030G215470H.fits 19 -- ft970629_1345_0030G216170H.fits 20 -- ft970629_1345_0030G216270H.fits 21 -- ft970629_1345_0030G217170H.fits 22 -- ft970629_1345_0030G217770H.fits 23 -- ft970629_1345_0030G218670H.fits 24 -- ft970629_1345_0030G219370H.fits 25 -- ft970629_1345_0030G219470H.fits 26 -- ft970629_1345_0030G220070H.fits 27 -- ft970629_1345_0030G220170H.fits 28 -- ft970629_1345_0030G221370H.fits 29 -- ft970629_1345_0030G221470H.fits 30 -- ft970629_1345_0030G222070H.fits 31 -- ft970629_1345_0030G223170H.fits 32 -- ft970629_1345_0030G224370H.fits 33 -- ft970629_1345_0030G224570H.fits 34 -- ft970629_1345_0030G225470H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G200170H.fits 2 -- ft970629_1345_0030G200570H.fits 3 -- ft970629_1345_0030G201970H.fits 4 -- ft970629_1345_0030G203570H.fits 5 -- ft970629_1345_0030G204770H.fits 6 -- ft970629_1345_0030G206270H.fits 7 -- ft970629_1345_0030G207070H.fits 8 -- ft970629_1345_0030G207670H.fits 9 -- ft970629_1345_0030G208470H.fits 10 -- ft970629_1345_0030G209070H.fits 11 -- ft970629_1345_0030G209670H.fits 12 -- ft970629_1345_0030G210270H.fits 13 -- ft970629_1345_0030G210870H.fits 14 -- ft970629_1345_0030G212070H.fits 15 -- ft970629_1345_0030G212670H.fits 16 -- ft970629_1345_0030G213870H.fits 17 -- ft970629_1345_0030G214470H.fits 18 -- ft970629_1345_0030G215470H.fits 19 -- ft970629_1345_0030G216170H.fits 20 -- ft970629_1345_0030G216270H.fits 21 -- ft970629_1345_0030G217170H.fits 22 -- ft970629_1345_0030G217770H.fits 23 -- ft970629_1345_0030G218670H.fits 24 -- ft970629_1345_0030G219370H.fits 25 -- ft970629_1345_0030G219470H.fits 26 -- ft970629_1345_0030G220070H.fits 27 -- ft970629_1345_0030G220170H.fits 28 -- ft970629_1345_0030G221370H.fits 29 -- ft970629_1345_0030G221470H.fits 30 -- ft970629_1345_0030G222070H.fits 31 -- ft970629_1345_0030G223170H.fits 32 -- ft970629_1345_0030G224370H.fits 33 -- ft970629_1345_0030G224570H.fits 34 -- ft970629_1345_0030G225470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000g200270m.unf
---- cmerge: version 1.6 ---- A total of 25 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G200370M.fits 2 -- ft970629_1345_0030G201570M.fits 3 -- ft970629_1345_0030G203170M.fits 4 -- ft970629_1345_0030G204370M.fits 5 -- ft970629_1345_0030G205870M.fits 6 -- ft970629_1345_0030G206470M.fits 7 -- ft970629_1345_0030G207270M.fits 8 -- ft970629_1345_0030G207870M.fits 9 -- ft970629_1345_0030G208070M.fits 10 -- ft970629_1345_0030G209270M.fits 11 -- ft970629_1345_0030G210470M.fits 12 -- ft970629_1345_0030G212270M.fits 13 -- ft970629_1345_0030G214070M.fits 14 -- ft970629_1345_0030G215070M.fits 15 -- ft970629_1345_0030G216070M.fits 16 -- ft970629_1345_0030G217370M.fits 17 -- ft970629_1345_0030G221670M.fits 18 -- ft970629_1345_0030G222270M.fits 19 -- ft970629_1345_0030G222770M.fits 20 -- ft970629_1345_0030G223370M.fits 21 -- ft970629_1345_0030G223970M.fits 22 -- ft970629_1345_0030G224770M.fits 23 -- ft970629_1345_0030G225070M.fits 24 -- ft970629_1345_0030G225670M.fits 25 -- ft970629_1345_0030G225870M.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G200370M.fits 2 -- ft970629_1345_0030G201570M.fits 3 -- ft970629_1345_0030G203170M.fits 4 -- ft970629_1345_0030G204370M.fits 5 -- ft970629_1345_0030G205870M.fits 6 -- ft970629_1345_0030G206470M.fits 7 -- ft970629_1345_0030G207270M.fits 8 -- ft970629_1345_0030G207870M.fits 9 -- ft970629_1345_0030G208070M.fits 10 -- ft970629_1345_0030G209270M.fits 11 -- ft970629_1345_0030G210470M.fits 12 -- ft970629_1345_0030G212270M.fits 13 -- ft970629_1345_0030G214070M.fits 14 -- ft970629_1345_0030G215070M.fits 15 -- ft970629_1345_0030G216070M.fits 16 -- ft970629_1345_0030G217370M.fits 17 -- ft970629_1345_0030G221670M.fits 18 -- ft970629_1345_0030G222270M.fits 19 -- ft970629_1345_0030G222770M.fits 20 -- ft970629_1345_0030G223370M.fits 21 -- ft970629_1345_0030G223970M.fits 22 -- ft970629_1345_0030G224770M.fits 23 -- ft970629_1345_0030G225070M.fits 24 -- ft970629_1345_0030G225670M.fits 25 -- ft970629_1345_0030G225870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000g200370l.unf
---- cmerge: version 1.6 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G200470L.fits 2 -- ft970629_1345_0030G201170L.fits 3 -- ft970629_1345_0030G202770L.fits 4 -- ft970629_1345_0030G203970L.fits 5 -- ft970629_1345_0030G205470L.fits 6 -- ft970629_1345_0030G206670L.fits 7 -- ft970629_1345_0030G207970L.fits 8 -- ft970629_1345_0030G208670L.fits 9 -- ft970629_1345_0030G218270L.fits 10 -- ft970629_1345_0030G219270L.fits 11 -- ft970629_1345_0030G222670L.fits 12 -- ft970629_1345_0030G223870L.fits 13 -- ft970629_1345_0030G224970L.fits 14 -- ft970629_1345_0030G225770L.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G200470L.fits 2 -- ft970629_1345_0030G201170L.fits 3 -- ft970629_1345_0030G202770L.fits 4 -- ft970629_1345_0030G203970L.fits 5 -- ft970629_1345_0030G205470L.fits 6 -- ft970629_1345_0030G206670L.fits 7 -- ft970629_1345_0030G207970L.fits 8 -- ft970629_1345_0030G208670L.fits 9 -- ft970629_1345_0030G218270L.fits 10 -- ft970629_1345_0030G219270L.fits 11 -- ft970629_1345_0030G222670L.fits 12 -- ft970629_1345_0030G223870L.fits 13 -- ft970629_1345_0030G224970L.fits 14 -- ft970629_1345_0030G225770L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000402 events
ft970629_1345_0030G200270M.fits ft970629_1345_0030G201470M.fits ft970629_1345_0030G203070M.fits ft970629_1345_0030G204270M.fits ft970629_1345_0030G205770M.fits ft970629_1345_0030G206370M.fits ft970629_1345_0030G207170M.fits ft970629_1345_0030G207770M.fits ft970629_1345_0030G209170M.fits ft970629_1345_0030G210370M.fits ft970629_1345_0030G212170M.fits ft970629_1345_0030G213970M.fits ft970629_1345_0030G217270M.fits ft970629_1345_0030G221570M.fits ft970629_1345_0030G222170M.fits ft970629_1345_0030G223270M.fits ft970629_1345_0030G224670M.fits ft970629_1345_0030G225570M.fits-> Ignoring the following files containing 000000258 events
ft970629_1345_0030G206570L.fits ft970629_1345_0030G208570L.fits ft970629_1345_0030G224870L.fits-> Ignoring the following files containing 000000192 events
ft970629_1345_0030G201070L.fits ft970629_1345_0030G202670L.fits ft970629_1345_0030G218170L.fits ft970629_1345_0030G219170L.fits ft970629_1345_0030G223770L.fits-> Ignoring the following files containing 000000030 events
ft970629_1345_0030G201870H.fits ft970629_1345_0030G203470H.fits ft970629_1345_0030G206170H.fits ft970629_1345_0030G206970H.fits ft970629_1345_0030G208370H.fits ft970629_1345_0030G209570H.fits ft970629_1345_0030G210770H.fits ft970629_1345_0030G212570H.fits ft970629_1345_0030G214370H.fits ft970629_1345_0030G215370H.fits ft970629_1345_0030G217670H.fits ft970629_1345_0030G218570H.fits ft970629_1345_0030G221970H.fits ft970629_1345_0030G223070H.fits ft970629_1345_0030G224270H.fits ft970629_1345_0030G225370H.fits-> Ignoring the following files containing 000000023 events
ft970629_1345_0030G203870L.fits ft970629_1345_0030G205370L.fits-> Ignoring the following files containing 000000021 events
ft970629_1345_0030G216970H.fits ft970629_1345_0030G219970H.fits-> Ignoring the following files containing 000000018 events
ft970629_1345_0030G204070M.fits-> Ignoring the following files containing 000000018 events
ft970629_1345_0030G201370M.fits-> Ignoring the following files containing 000000018 events
ft970629_1345_0030G205670M.fits-> Ignoring the following files containing 000000017 events
ft970629_1345_0030G202970M.fits-> Ignoring the following files containing 000000013 events
ft970629_1345_0030G201270M.fits-> Ignoring the following files containing 000000012 events
ft970629_1345_0030G214970M.fits ft970629_1345_0030G215970M.fits-> Ignoring the following files containing 000000010 events
ft970629_1345_0030G202870M.fits-> Ignoring the following files containing 000000009 events
ft970629_1345_0030G210170H.fits ft970629_1345_0030G211970H.fits ft970629_1345_0030G213770H.fits ft970629_1345_0030G221270H.fits-> Ignoring the following files containing 000000008 events
ft970629_1345_0030G204170M.fits-> Ignoring the following files containing 000000008 events
ft970629_1345_0030G205570M.fits-> Ignoring the following files containing 000000008 events
ft970629_1345_0030G210070H.fits ft970629_1345_0030G211870H.fits ft970629_1345_0030G213670H.fits ft970629_1345_0030G221170H.fits-> Ignoring the following files containing 000000006 events
ft970629_1345_0030G208770H.fits-> Ignoring the following files containing 000000005 events
ft970629_1345_0030G224470H.fits-> Ignoring the following files containing 000000005 events
ft970629_1345_0030G209970H.fits ft970629_1345_0030G211770H.fits-> Ignoring the following files containing 000000005 events
ft970629_1345_0030G203670H.fits ft970629_1345_0030G217870H.fits ft970629_1345_0030G218770H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G212470H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G217570H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G204570H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G201770H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G204470H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G222970H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G203370H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G216370H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G216870H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G215270H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G214270H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G218370H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G201670H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G206770H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G205970H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G209370H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G224070H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G208170H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G219870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G217070H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G215170H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G214170H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G225170H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G218470H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G210670H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G210570H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G217470H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G206870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G207370H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G209470H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G224170H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G203270H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G208870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G221870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G221770H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 3 photon cnt = 3 GISSORTSPLIT:LO:g300470h.prelist merge count = 3 photon cnt = 4 GISSORTSPLIT:LO:g300570h.prelist merge count = 3 photon cnt = 8 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301070h.prelist merge count = 33 photon cnt = 30570 GISSORTSPLIT:LO:g301170h.prelist merge count = 14 photon cnt = 21 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301870h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302170h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g302270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g302470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g302570h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302970h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g303070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g303370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g303470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g303570h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303970h.prelist merge count = 2 photon cnt = 20 GISSORTSPLIT:LO:g300170l.prelist merge count = 2 photon cnt = 27 GISSORTSPLIT:LO:g300270l.prelist merge count = 5 photon cnt = 175 GISSORTSPLIT:LO:g300370l.prelist merge count = 14 photon cnt = 11366 GISSORTSPLIT:LO:g300470l.prelist merge count = 3 photon cnt = 274 GISSORTSPLIT:LO:g300170m.prelist merge count = 2 photon cnt = 12 GISSORTSPLIT:LO:g300270m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g300370m.prelist merge count = 26 photon cnt = 19495 GISSORTSPLIT:LO:g300470m.prelist merge count = 18 photon cnt = 407 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g300970m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g301070m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g301170m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g301270m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:Total filenames split = 170 GISSORTSPLIT:LO:Total split file cnt = 55 GISSORTSPLIT:LO:End program-> Creating ad75071000g300170h.unf
---- cmerge: version 1.6 ---- A total of 33 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G300170H.fits 2 -- ft970629_1345_0030G300570H.fits 3 -- ft970629_1345_0030G301970H.fits 4 -- ft970629_1345_0030G303570H.fits 5 -- ft970629_1345_0030G304770H.fits 6 -- ft970629_1345_0030G306270H.fits 7 -- ft970629_1345_0030G307070H.fits 8 -- ft970629_1345_0030G307670H.fits 9 -- ft970629_1345_0030G308470H.fits 10 -- ft970629_1345_0030G309070H.fits 11 -- ft970629_1345_0030G309670H.fits 12 -- ft970629_1345_0030G310270H.fits 13 -- ft970629_1345_0030G310870H.fits 14 -- ft970629_1345_0030G312070H.fits 15 -- ft970629_1345_0030G312670H.fits 16 -- ft970629_1345_0030G313870H.fits 17 -- ft970629_1345_0030G314470H.fits 18 -- ft970629_1345_0030G315470H.fits 19 -- ft970629_1345_0030G316170H.fits 20 -- ft970629_1345_0030G316270H.fits 21 -- ft970629_1345_0030G317170H.fits 22 -- ft970629_1345_0030G317770H.fits 23 -- ft970629_1345_0030G318670H.fits 24 -- ft970629_1345_0030G319370H.fits 25 -- ft970629_1345_0030G319470H.fits 26 -- ft970629_1345_0030G320170H.fits 27 -- ft970629_1345_0030G320270H.fits 28 -- ft970629_1345_0030G321470H.fits 29 -- ft970629_1345_0030G321570H.fits 30 -- ft970629_1345_0030G322170H.fits 31 -- ft970629_1345_0030G323270H.fits 32 -- ft970629_1345_0030G324670H.fits 33 -- ft970629_1345_0030G325570H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G300170H.fits 2 -- ft970629_1345_0030G300570H.fits 3 -- ft970629_1345_0030G301970H.fits 4 -- ft970629_1345_0030G303570H.fits 5 -- ft970629_1345_0030G304770H.fits 6 -- ft970629_1345_0030G306270H.fits 7 -- ft970629_1345_0030G307070H.fits 8 -- ft970629_1345_0030G307670H.fits 9 -- ft970629_1345_0030G308470H.fits 10 -- ft970629_1345_0030G309070H.fits 11 -- ft970629_1345_0030G309670H.fits 12 -- ft970629_1345_0030G310270H.fits 13 -- ft970629_1345_0030G310870H.fits 14 -- ft970629_1345_0030G312070H.fits 15 -- ft970629_1345_0030G312670H.fits 16 -- ft970629_1345_0030G313870H.fits 17 -- ft970629_1345_0030G314470H.fits 18 -- ft970629_1345_0030G315470H.fits 19 -- ft970629_1345_0030G316170H.fits 20 -- ft970629_1345_0030G316270H.fits 21 -- ft970629_1345_0030G317170H.fits 22 -- ft970629_1345_0030G317770H.fits 23 -- ft970629_1345_0030G318670H.fits 24 -- ft970629_1345_0030G319370H.fits 25 -- ft970629_1345_0030G319470H.fits 26 -- ft970629_1345_0030G320170H.fits 27 -- ft970629_1345_0030G320270H.fits 28 -- ft970629_1345_0030G321470H.fits 29 -- ft970629_1345_0030G321570H.fits 30 -- ft970629_1345_0030G322170H.fits 31 -- ft970629_1345_0030G323270H.fits 32 -- ft970629_1345_0030G324670H.fits 33 -- ft970629_1345_0030G325570H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000g300270m.unf
---- cmerge: version 1.6 ---- A total of 26 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G300370M.fits 2 -- ft970629_1345_0030G301570M.fits 3 -- ft970629_1345_0030G303170M.fits 4 -- ft970629_1345_0030G304370M.fits 5 -- ft970629_1345_0030G305870M.fits 6 -- ft970629_1345_0030G306470M.fits 7 -- ft970629_1345_0030G307270M.fits 8 -- ft970629_1345_0030G307870M.fits 9 -- ft970629_1345_0030G308070M.fits 10 -- ft970629_1345_0030G309270M.fits 11 -- ft970629_1345_0030G310470M.fits 12 -- ft970629_1345_0030G312270M.fits 13 -- ft970629_1345_0030G314070M.fits 14 -- ft970629_1345_0030G315070M.fits 15 -- ft970629_1345_0030G316070M.fits 16 -- ft970629_1345_0030G317370M.fits 17 -- ft970629_1345_0030G321770M.fits 18 -- ft970629_1345_0030G322370M.fits 19 -- ft970629_1345_0030G322870M.fits 20 -- ft970629_1345_0030G323470M.fits 21 -- ft970629_1345_0030G324070M.fits 22 -- ft970629_1345_0030G324270M.fits 23 -- ft970629_1345_0030G324870M.fits 24 -- ft970629_1345_0030G325170M.fits 25 -- ft970629_1345_0030G325770M.fits 26 -- ft970629_1345_0030G325970M.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G300370M.fits 2 -- ft970629_1345_0030G301570M.fits 3 -- ft970629_1345_0030G303170M.fits 4 -- ft970629_1345_0030G304370M.fits 5 -- ft970629_1345_0030G305870M.fits 6 -- ft970629_1345_0030G306470M.fits 7 -- ft970629_1345_0030G307270M.fits 8 -- ft970629_1345_0030G307870M.fits 9 -- ft970629_1345_0030G308070M.fits 10 -- ft970629_1345_0030G309270M.fits 11 -- ft970629_1345_0030G310470M.fits 12 -- ft970629_1345_0030G312270M.fits 13 -- ft970629_1345_0030G314070M.fits 14 -- ft970629_1345_0030G315070M.fits 15 -- ft970629_1345_0030G316070M.fits 16 -- ft970629_1345_0030G317370M.fits 17 -- ft970629_1345_0030G321770M.fits 18 -- ft970629_1345_0030G322370M.fits 19 -- ft970629_1345_0030G322870M.fits 20 -- ft970629_1345_0030G323470M.fits 21 -- ft970629_1345_0030G324070M.fits 22 -- ft970629_1345_0030G324270M.fits 23 -- ft970629_1345_0030G324870M.fits 24 -- ft970629_1345_0030G325170M.fits 25 -- ft970629_1345_0030G325770M.fits 26 -- ft970629_1345_0030G325970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000g300370l.unf
---- cmerge: version 1.6 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030G300470L.fits 2 -- ft970629_1345_0030G301170L.fits 3 -- ft970629_1345_0030G302770L.fits 4 -- ft970629_1345_0030G303970L.fits 5 -- ft970629_1345_0030G305470L.fits 6 -- ft970629_1345_0030G306670L.fits 7 -- ft970629_1345_0030G307970L.fits 8 -- ft970629_1345_0030G308670L.fits 9 -- ft970629_1345_0030G318270L.fits 10 -- ft970629_1345_0030G319270L.fits 11 -- ft970629_1345_0030G322770L.fits 12 -- ft970629_1345_0030G323970L.fits 13 -- ft970629_1345_0030G325070L.fits 14 -- ft970629_1345_0030G325870L.fits Merging binary extension #: 2 1 -- ft970629_1345_0030G300470L.fits 2 -- ft970629_1345_0030G301170L.fits 3 -- ft970629_1345_0030G302770L.fits 4 -- ft970629_1345_0030G303970L.fits 5 -- ft970629_1345_0030G305470L.fits 6 -- ft970629_1345_0030G306670L.fits 7 -- ft970629_1345_0030G307970L.fits 8 -- ft970629_1345_0030G308670L.fits 9 -- ft970629_1345_0030G318270L.fits 10 -- ft970629_1345_0030G319270L.fits 11 -- ft970629_1345_0030G322770L.fits 12 -- ft970629_1345_0030G323970L.fits 13 -- ft970629_1345_0030G325070L.fits 14 -- ft970629_1345_0030G325870L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000407 events
ft970629_1345_0030G300270M.fits ft970629_1345_0030G301470M.fits ft970629_1345_0030G303070M.fits ft970629_1345_0030G304270M.fits ft970629_1345_0030G305770M.fits ft970629_1345_0030G306370M.fits ft970629_1345_0030G307170M.fits ft970629_1345_0030G307770M.fits ft970629_1345_0030G309170M.fits ft970629_1345_0030G310370M.fits ft970629_1345_0030G312170M.fits ft970629_1345_0030G313970M.fits ft970629_1345_0030G317270M.fits ft970629_1345_0030G321670M.fits ft970629_1345_0030G322270M.fits ft970629_1345_0030G323370M.fits ft970629_1345_0030G324770M.fits ft970629_1345_0030G325670M.fits-> Ignoring the following files containing 000000274 events
ft970629_1345_0030G306570L.fits ft970629_1345_0030G308570L.fits ft970629_1345_0030G324970L.fits-> Ignoring the following files containing 000000175 events
ft970629_1345_0030G301070L.fits ft970629_1345_0030G302670L.fits ft970629_1345_0030G318170L.fits ft970629_1345_0030G319170L.fits ft970629_1345_0030G323870L.fits-> Ignoring the following files containing 000000027 events
ft970629_1345_0030G303870L.fits ft970629_1345_0030G305370L.fits-> Ignoring the following files containing 000000021 events
ft970629_1345_0030G301870H.fits ft970629_1345_0030G303470H.fits ft970629_1345_0030G304670H.fits ft970629_1345_0030G306170H.fits ft970629_1345_0030G306970H.fits ft970629_1345_0030G307570H.fits ft970629_1345_0030G308370H.fits ft970629_1345_0030G308970H.fits ft970629_1345_0030G309570H.fits ft970629_1345_0030G314370H.fits ft970629_1345_0030G315370H.fits ft970629_1345_0030G318570H.fits ft970629_1345_0030G323170H.fits ft970629_1345_0030G325470H.fits-> Ignoring the following files containing 000000020 events
ft970629_1345_0030G316470H.fits ft970629_1345_0030G319570H.fits-> Ignoring the following files containing 000000015 events
ft970629_1345_0030G301370M.fits-> Ignoring the following files containing 000000015 events
ft970629_1345_0030G304170M.fits-> Ignoring the following files containing 000000013 events
ft970629_1345_0030G302870M.fits-> Ignoring the following files containing 000000012 events
ft970629_1345_0030G304070M.fits-> Ignoring the following files containing 000000012 events
ft970629_1345_0030G305670M.fits-> Ignoring the following files containing 000000012 events
ft970629_1345_0030G314970M.fits ft970629_1345_0030G315970M.fits-> Ignoring the following files containing 000000011 events
ft970629_1345_0030G301270M.fits-> Ignoring the following files containing 000000011 events
ft970629_1345_0030G305570M.fits-> Ignoring the following files containing 000000010 events
ft970629_1345_0030G324170M.fits-> Ignoring the following files containing 000000009 events
ft970629_1345_0030G302970M.fits-> Ignoring the following files containing 000000008 events
ft970629_1345_0030G310070H.fits ft970629_1345_0030G311870H.fits ft970629_1345_0030G313670H.fits-> Ignoring the following files containing 000000005 events
ft970629_1345_0030G303270H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G309370H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G315270H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G313770H.fits-> Ignoring the following files containing 000000004 events
ft970629_1345_0030G309970H.fits ft970629_1345_0030G311770H.fits ft970629_1345_0030G321170H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G308770H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G315170H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G325370H.fits-> Ignoring the following files containing 000000003 events
ft970629_1345_0030G302070H.fits ft970629_1345_0030G318770H.fits ft970629_1345_0030G320370H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G301670H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G317570H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G307470H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G323070H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G303370H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G305970H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G308170H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G318470H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G317070H.fits-> Ignoring the following files containing 000000002 events
ft970629_1345_0030G320070H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G319670H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G310670H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G310570H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G309470H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G312470H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G308870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G304570H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G314270H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G306070H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G325270H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G318370H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G306870H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G306770H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G316370H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G316970H.fits-> Ignoring the following files containing 000000001 events
ft970629_1345_0030G319970H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 25 photon cnt = 496046 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 11 photon cnt = 143414 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 3 photon cnt = 768 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 3 photon cnt = 208 SIS0SORTSPLIT:LO:s000502h.prelist merge count = 2 photon cnt = 1767 SIS0SORTSPLIT:LO:s000602h.prelist merge count = 1 photon cnt = 76 SIS0SORTSPLIT:LO:s000702l.prelist merge count = 17 photon cnt = 87731 SIS0SORTSPLIT:LO:s000802l.prelist merge count = 13 photon cnt = 17331 SIS0SORTSPLIT:LO:s000902m.prelist merge count = 29 photon cnt = 207224 SIS0SORTSPLIT:LO:s001002m.prelist merge count = 12 photon cnt = 34336 SIS0SORTSPLIT:LO:s001102m.prelist merge count = 2 photon cnt = 131 SIS0SORTSPLIT:LO:Total filenames split = 118 SIS0SORTSPLIT:LO:Total split file cnt = 11 SIS0SORTSPLIT:LO:End program-> Creating ad75071000s000101h.unf
---- cmerge: version 1.6 ---- A total of 25 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S000501H.fits 2 -- ft970629_1345_0030S001201H.fits 3 -- ft970629_1345_0030S002001H.fits 4 -- ft970629_1345_0030S002601H.fits 5 -- ft970629_1345_0030S003201H.fits 6 -- ft970629_1345_0030S003701H.fits 7 -- ft970629_1345_0030S004101H.fits 8 -- ft970629_1345_0030S004701H.fits 9 -- ft970629_1345_0030S005201H.fits 10 -- ft970629_1345_0030S005701H.fits 11 -- ft970629_1345_0030S006101H.fits 12 -- ft970629_1345_0030S006301H.fits 13 -- ft970629_1345_0030S006701H.fits 14 -- ft970629_1345_0030S007101H.fits 15 -- ft970629_1345_0030S007501H.fits 16 -- ft970629_1345_0030S008101H.fits 17 -- ft970629_1345_0030S008701H.fits 18 -- ft970629_1345_0030S008901H.fits 19 -- ft970629_1345_0030S009701H.fits 20 -- ft970629_1345_0030S010501H.fits 21 -- ft970629_1345_0030S011101H.fits 22 -- ft970629_1345_0030S011301H.fits 23 -- ft970629_1345_0030S012001H.fits 24 -- ft970629_1345_0030S012601H.fits 25 -- ft970629_1345_0030S013201H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S000501H.fits 2 -- ft970629_1345_0030S001201H.fits 3 -- ft970629_1345_0030S002001H.fits 4 -- ft970629_1345_0030S002601H.fits 5 -- ft970629_1345_0030S003201H.fits 6 -- ft970629_1345_0030S003701H.fits 7 -- ft970629_1345_0030S004101H.fits 8 -- ft970629_1345_0030S004701H.fits 9 -- ft970629_1345_0030S005201H.fits 10 -- ft970629_1345_0030S005701H.fits 11 -- ft970629_1345_0030S006101H.fits 12 -- ft970629_1345_0030S006301H.fits 13 -- ft970629_1345_0030S006701H.fits 14 -- ft970629_1345_0030S007101H.fits 15 -- ft970629_1345_0030S007501H.fits 16 -- ft970629_1345_0030S008101H.fits 17 -- ft970629_1345_0030S008701H.fits 18 -- ft970629_1345_0030S008901H.fits 19 -- ft970629_1345_0030S009701H.fits 20 -- ft970629_1345_0030S010501H.fits 21 -- ft970629_1345_0030S011101H.fits 22 -- ft970629_1345_0030S011301H.fits 23 -- ft970629_1345_0030S012001H.fits 24 -- ft970629_1345_0030S012601H.fits 25 -- ft970629_1345_0030S013201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000202m.unf
---- cmerge: version 1.6 ---- A total of 29 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S000202M.fits 2 -- ft970629_1345_0030S001102M.fits 3 -- ft970629_1345_0030S001302M.fits 4 -- ft970629_1345_0030S001902M.fits 5 -- ft970629_1345_0030S002502M.fits 6 -- ft970629_1345_0030S003102M.fits 7 -- ft970629_1345_0030S003302M.fits 8 -- ft970629_1345_0030S004002M.fits 9 -- ft970629_1345_0030S004202M.fits 10 -- ft970629_1345_0030S004602M.fits 11 -- ft970629_1345_0030S005502M.fits 12 -- ft970629_1345_0030S006002M.fits 13 -- ft970629_1345_0030S006202M.fits 14 -- ft970629_1345_0030S007002M.fits 15 -- ft970629_1345_0030S007802M.fits 16 -- ft970629_1345_0030S008002M.fits 17 -- ft970629_1345_0030S008602M.fits 18 -- ft970629_1345_0030S008802M.fits 19 -- ft970629_1345_0030S010602M.fits 20 -- ft970629_1345_0030S011202M.fits 21 -- ft970629_1345_0030S011402M.fits 22 -- ft970629_1345_0030S011902M.fits 23 -- ft970629_1345_0030S012102M.fits 24 -- ft970629_1345_0030S012502M.fits 25 -- ft970629_1345_0030S012702M.fits 26 -- ft970629_1345_0030S013102M.fits 27 -- ft970629_1345_0030S013302M.fits 28 -- ft970629_1345_0030S013502M.fits 29 -- ft970629_1345_0030S013902M.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S000202M.fits 2 -- ft970629_1345_0030S001102M.fits 3 -- ft970629_1345_0030S001302M.fits 4 -- ft970629_1345_0030S001902M.fits 5 -- ft970629_1345_0030S002502M.fits 6 -- ft970629_1345_0030S003102M.fits 7 -- ft970629_1345_0030S003302M.fits 8 -- ft970629_1345_0030S004002M.fits 9 -- ft970629_1345_0030S004202M.fits 10 -- ft970629_1345_0030S004602M.fits 11 -- ft970629_1345_0030S005502M.fits 12 -- ft970629_1345_0030S006002M.fits 13 -- ft970629_1345_0030S006202M.fits 14 -- ft970629_1345_0030S007002M.fits 15 -- ft970629_1345_0030S007802M.fits 16 -- ft970629_1345_0030S008002M.fits 17 -- ft970629_1345_0030S008602M.fits 18 -- ft970629_1345_0030S008802M.fits 19 -- ft970629_1345_0030S010602M.fits 20 -- ft970629_1345_0030S011202M.fits 21 -- ft970629_1345_0030S011402M.fits 22 -- ft970629_1345_0030S011902M.fits 23 -- ft970629_1345_0030S012102M.fits 24 -- ft970629_1345_0030S012502M.fits 25 -- ft970629_1345_0030S012702M.fits 26 -- ft970629_1345_0030S013102M.fits 27 -- ft970629_1345_0030S013302M.fits 28 -- ft970629_1345_0030S013502M.fits 29 -- ft970629_1345_0030S013902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000301h.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S000101H.fits 2 -- ft970629_1345_0030S002701H.fits 3 -- ft970629_1345_0030S003801H.fits 4 -- ft970629_1345_0030S004801H.fits 5 -- ft970629_1345_0030S005301H.fits 6 -- ft970629_1345_0030S005801H.fits 7 -- ft970629_1345_0030S006401H.fits 8 -- ft970629_1345_0030S006601H.fits 9 -- ft970629_1345_0030S007201H.fits 10 -- ft970629_1345_0030S007401H.fits 11 -- ft970629_1345_0030S011001H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S000101H.fits 2 -- ft970629_1345_0030S002701H.fits 3 -- ft970629_1345_0030S003801H.fits 4 -- ft970629_1345_0030S004801H.fits 5 -- ft970629_1345_0030S005301H.fits 6 -- ft970629_1345_0030S005801H.fits 7 -- ft970629_1345_0030S006401H.fits 8 -- ft970629_1345_0030S006601H.fits 9 -- ft970629_1345_0030S007201H.fits 10 -- ft970629_1345_0030S007401H.fits 11 -- ft970629_1345_0030S011001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000402l.unf
---- cmerge: version 1.6 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S000302L.fits 2 -- ft970629_1345_0030S001002L.fits 3 -- ft970629_1345_0030S001802L.fits 4 -- ft970629_1345_0030S002402L.fits 5 -- ft970629_1345_0030S003002L.fits 6 -- ft970629_1345_0030S003602L.fits 7 -- ft970629_1345_0030S004502L.fits 8 -- ft970629_1345_0030S005102L.fits 9 -- ft970629_1345_0030S009102L.fits 10 -- ft970629_1345_0030S009502L.fits 11 -- ft970629_1345_0030S009902L.fits 12 -- ft970629_1345_0030S010302L.fits 13 -- ft970629_1345_0030S011502L.fits 14 -- ft970629_1345_0030S011802L.fits 15 -- ft970629_1345_0030S012402L.fits 16 -- ft970629_1345_0030S013002L.fits 17 -- ft970629_1345_0030S013802L.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S000302L.fits 2 -- ft970629_1345_0030S001002L.fits 3 -- ft970629_1345_0030S001802L.fits 4 -- ft970629_1345_0030S002402L.fits 5 -- ft970629_1345_0030S003002L.fits 6 -- ft970629_1345_0030S003602L.fits 7 -- ft970629_1345_0030S004502L.fits 8 -- ft970629_1345_0030S005102L.fits 9 -- ft970629_1345_0030S009102L.fits 10 -- ft970629_1345_0030S009502L.fits 11 -- ft970629_1345_0030S009902L.fits 12 -- ft970629_1345_0030S010302L.fits 13 -- ft970629_1345_0030S011502L.fits 14 -- ft970629_1345_0030S011802L.fits 15 -- ft970629_1345_0030S012402L.fits 16 -- ft970629_1345_0030S013002L.fits 17 -- ft970629_1345_0030S013802L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000502m.unf
---- cmerge: version 1.6 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S002802M.fits 2 -- ft970629_1345_0030S003402M.fits 3 -- ft970629_1345_0030S003902M.fits 4 -- ft970629_1345_0030S004302M.fits 5 -- ft970629_1345_0030S005402M.fits 6 -- ft970629_1345_0030S005902M.fits 7 -- ft970629_1345_0030S007902M.fits 8 -- ft970629_1345_0030S008502M.fits 9 -- ft970629_1345_0030S012202M.fits 10 -- ft970629_1345_0030S012802M.fits 11 -- ft970629_1345_0030S013602M.fits 12 -- ft970629_1345_0030S014002M.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S002802M.fits 2 -- ft970629_1345_0030S003402M.fits 3 -- ft970629_1345_0030S003902M.fits 4 -- ft970629_1345_0030S004302M.fits 5 -- ft970629_1345_0030S005402M.fits 6 -- ft970629_1345_0030S005902M.fits 7 -- ft970629_1345_0030S007902M.fits 8 -- ft970629_1345_0030S008502M.fits 9 -- ft970629_1345_0030S012202M.fits 10 -- ft970629_1345_0030S012802M.fits 11 -- ft970629_1345_0030S013602M.fits 12 -- ft970629_1345_0030S014002M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000602l.unf
---- cmerge: version 1.6 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S000902L.fits 2 -- ft970629_1345_0030S001702L.fits 3 -- ft970629_1345_0030S002302L.fits 4 -- ft970629_1345_0030S002902L.fits 5 -- ft970629_1345_0030S003502L.fits 6 -- ft970629_1345_0030S004402L.fits 7 -- ft970629_1345_0030S005002L.fits 8 -- ft970629_1345_0030S009402L.fits 9 -- ft970629_1345_0030S010202L.fits 10 -- ft970629_1345_0030S011702L.fits 11 -- ft970629_1345_0030S012302L.fits 12 -- ft970629_1345_0030S012902L.fits 13 -- ft970629_1345_0030S013702L.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S000902L.fits 2 -- ft970629_1345_0030S001702L.fits 3 -- ft970629_1345_0030S002302L.fits 4 -- ft970629_1345_0030S002902L.fits 5 -- ft970629_1345_0030S003502L.fits 6 -- ft970629_1345_0030S004402L.fits 7 -- ft970629_1345_0030S005002L.fits 8 -- ft970629_1345_0030S009402L.fits 9 -- ft970629_1345_0030S010202L.fits 10 -- ft970629_1345_0030S011702L.fits 11 -- ft970629_1345_0030S012302L.fits 12 -- ft970629_1345_0030S012902L.fits 13 -- ft970629_1345_0030S013702L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s000702h.unf
---- cmerge: version 1.6 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S009002H.fits 2 -- ft970629_1345_0030S009802H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S009002H.fits 2 -- ft970629_1345_0030S009802H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000768 events
ft970629_1345_0030S006801H.fits ft970629_1345_0030S007601H.fits ft970629_1345_0030S008201H.fits-> Ignoring the following files containing 000000208 events
ft970629_1345_0030S000401L.fits ft970629_1345_0030S009601L.fits ft970629_1345_0030S010401L.fits-> Ignoring the following files containing 000000131 events
ft970629_1345_0030S010702M.fits ft970629_1345_0030S013402M.fits-> Ignoring the following files containing 000000076 events
ft970629_1345_0030S004902H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 26 photon cnt = 971865 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 3 photon cnt = 768 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 3 photon cnt = 208 SIS1SORTSPLIT:LO:s100402h.prelist merge count = 3 photon cnt = 1865 SIS1SORTSPLIT:LO:s100502l.prelist merge count = 17 photon cnt = 123973 SIS1SORTSPLIT:LO:s100602l.prelist merge count = 1 photon cnt = 128 SIS1SORTSPLIT:LO:s100702m.prelist merge count = 29 photon cnt = 459114 SIS1SORTSPLIT:LO:s100802m.prelist merge count = 2 photon cnt = 240 SIS1SORTSPLIT:LO:Total filenames split = 84 SIS1SORTSPLIT:LO:Total split file cnt = 8 SIS1SORTSPLIT:LO:End program-> Creating ad75071000s100101h.unf
---- cmerge: version 1.6 ---- A total of 26 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S100101H.fits 2 -- ft970629_1345_0030S100501H.fits 3 -- ft970629_1345_0030S101001H.fits 4 -- ft970629_1345_0030S101601H.fits 5 -- ft970629_1345_0030S102101H.fits 6 -- ft970629_1345_0030S102501H.fits 7 -- ft970629_1345_0030S102801H.fits 8 -- ft970629_1345_0030S103001H.fits 9 -- ft970629_1345_0030S103401H.fits 10 -- ft970629_1345_0030S103701H.fits 11 -- ft970629_1345_0030S104001H.fits 12 -- ft970629_1345_0030S104201H.fits 13 -- ft970629_1345_0030S104401H.fits 14 -- ft970629_1345_0030S104601H.fits 15 -- ft970629_1345_0030S105001H.fits 16 -- ft970629_1345_0030S105201H.fits 17 -- ft970629_1345_0030S105601H.fits 18 -- ft970629_1345_0030S106001H.fits 19 -- ft970629_1345_0030S106201H.fits 20 -- ft970629_1345_0030S106801H.fits 21 -- ft970629_1345_0030S107401H.fits 22 -- ft970629_1345_0030S107801H.fits 23 -- ft970629_1345_0030S108001H.fits 24 -- ft970629_1345_0030S108601H.fits 25 -- ft970629_1345_0030S109001H.fits 26 -- ft970629_1345_0030S109401H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S100101H.fits 2 -- ft970629_1345_0030S100501H.fits 3 -- ft970629_1345_0030S101001H.fits 4 -- ft970629_1345_0030S101601H.fits 5 -- ft970629_1345_0030S102101H.fits 6 -- ft970629_1345_0030S102501H.fits 7 -- ft970629_1345_0030S102801H.fits 8 -- ft970629_1345_0030S103001H.fits 9 -- ft970629_1345_0030S103401H.fits 10 -- ft970629_1345_0030S103701H.fits 11 -- ft970629_1345_0030S104001H.fits 12 -- ft970629_1345_0030S104201H.fits 13 -- ft970629_1345_0030S104401H.fits 14 -- ft970629_1345_0030S104601H.fits 15 -- ft970629_1345_0030S105001H.fits 16 -- ft970629_1345_0030S105201H.fits 17 -- ft970629_1345_0030S105601H.fits 18 -- ft970629_1345_0030S106001H.fits 19 -- ft970629_1345_0030S106201H.fits 20 -- ft970629_1345_0030S106801H.fits 21 -- ft970629_1345_0030S107401H.fits 22 -- ft970629_1345_0030S107801H.fits 23 -- ft970629_1345_0030S108001H.fits 24 -- ft970629_1345_0030S108601H.fits 25 -- ft970629_1345_0030S109001H.fits 26 -- ft970629_1345_0030S109401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s100202m.unf
---- cmerge: version 1.6 ---- A total of 29 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S100202M.fits 2 -- ft970629_1345_0030S100902M.fits 3 -- ft970629_1345_0030S101102M.fits 4 -- ft970629_1345_0030S101502M.fits 5 -- ft970629_1345_0030S102002M.fits 6 -- ft970629_1345_0030S102202M.fits 7 -- ft970629_1345_0030S102402M.fits 8 -- ft970629_1345_0030S102602M.fits 9 -- ft970629_1345_0030S102902M.fits 10 -- ft970629_1345_0030S103102M.fits 11 -- ft970629_1345_0030S103302M.fits 12 -- ft970629_1345_0030S103802M.fits 13 -- ft970629_1345_0030S104102M.fits 14 -- ft970629_1345_0030S104302M.fits 15 -- ft970629_1345_0030S104902M.fits 16 -- ft970629_1345_0030S105502M.fits 17 -- ft970629_1345_0030S105902M.fits 18 -- ft970629_1345_0030S106102M.fits 19 -- ft970629_1345_0030S107502M.fits 20 -- ft970629_1345_0030S107902M.fits 21 -- ft970629_1345_0030S108102M.fits 22 -- ft970629_1345_0030S108502M.fits 23 -- ft970629_1345_0030S108702M.fits 24 -- ft970629_1345_0030S108902M.fits 25 -- ft970629_1345_0030S109102M.fits 26 -- ft970629_1345_0030S109302M.fits 27 -- ft970629_1345_0030S109502M.fits 28 -- ft970629_1345_0030S109702M.fits 29 -- ft970629_1345_0030S109902M.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S100202M.fits 2 -- ft970629_1345_0030S100902M.fits 3 -- ft970629_1345_0030S101102M.fits 4 -- ft970629_1345_0030S101502M.fits 5 -- ft970629_1345_0030S102002M.fits 6 -- ft970629_1345_0030S102202M.fits 7 -- ft970629_1345_0030S102402M.fits 8 -- ft970629_1345_0030S102602M.fits 9 -- ft970629_1345_0030S102902M.fits 10 -- ft970629_1345_0030S103102M.fits 11 -- ft970629_1345_0030S103302M.fits 12 -- ft970629_1345_0030S103802M.fits 13 -- ft970629_1345_0030S104102M.fits 14 -- ft970629_1345_0030S104302M.fits 15 -- ft970629_1345_0030S104902M.fits 16 -- ft970629_1345_0030S105502M.fits 17 -- ft970629_1345_0030S105902M.fits 18 -- ft970629_1345_0030S106102M.fits 19 -- ft970629_1345_0030S107502M.fits 20 -- ft970629_1345_0030S107902M.fits 21 -- ft970629_1345_0030S108102M.fits 22 -- ft970629_1345_0030S108502M.fits 23 -- ft970629_1345_0030S108702M.fits 24 -- ft970629_1345_0030S108902M.fits 25 -- ft970629_1345_0030S109102M.fits 26 -- ft970629_1345_0030S109302M.fits 27 -- ft970629_1345_0030S109502M.fits 28 -- ft970629_1345_0030S109702M.fits 29 -- ft970629_1345_0030S109902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s100302l.unf
---- cmerge: version 1.6 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S100302L.fits 2 -- ft970629_1345_0030S100802L.fits 3 -- ft970629_1345_0030S101402L.fits 4 -- ft970629_1345_0030S101902L.fits 5 -- ft970629_1345_0030S102302L.fits 6 -- ft970629_1345_0030S102702L.fits 7 -- ft970629_1345_0030S103202L.fits 8 -- ft970629_1345_0030S103602L.fits 9 -- ft970629_1345_0030S106402L.fits 10 -- ft970629_1345_0030S106602L.fits 11 -- ft970629_1345_0030S107002L.fits 12 -- ft970629_1345_0030S107202L.fits 13 -- ft970629_1345_0030S108202L.fits 14 -- ft970629_1345_0030S108402L.fits 15 -- ft970629_1345_0030S108802L.fits 16 -- ft970629_1345_0030S109202L.fits 17 -- ft970629_1345_0030S109802L.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S100302L.fits 2 -- ft970629_1345_0030S100802L.fits 3 -- ft970629_1345_0030S101402L.fits 4 -- ft970629_1345_0030S101902L.fits 5 -- ft970629_1345_0030S102302L.fits 6 -- ft970629_1345_0030S102702L.fits 7 -- ft970629_1345_0030S103202L.fits 8 -- ft970629_1345_0030S103602L.fits 9 -- ft970629_1345_0030S106402L.fits 10 -- ft970629_1345_0030S106602L.fits 11 -- ft970629_1345_0030S107002L.fits 12 -- ft970629_1345_0030S107202L.fits 13 -- ft970629_1345_0030S108202L.fits 14 -- ft970629_1345_0030S108402L.fits 15 -- ft970629_1345_0030S108802L.fits 16 -- ft970629_1345_0030S109202L.fits 17 -- ft970629_1345_0030S109802L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad75071000s100402h.unf
---- cmerge: version 1.6 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970629_1345_0030S103502H.fits 2 -- ft970629_1345_0030S106302H.fits 3 -- ft970629_1345_0030S106902H.fits Merging binary extension #: 2 1 -- ft970629_1345_0030S103502H.fits 2 -- ft970629_1345_0030S106302H.fits 3 -- ft970629_1345_0030S106902H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000768 events
ft970629_1345_0030S104701H.fits ft970629_1345_0030S105301H.fits ft970629_1345_0030S105701H.fits-> Ignoring the following files containing 000000240 events
ft970629_1345_0030S107602M.fits ft970629_1345_0030S109602M.fits-> Ignoring the following files containing 000000208 events
ft970629_1345_0030S100401L.fits ft970629_1345_0030S106701L.fits ft970629_1345_0030S107301L.fits-> Ignoring the following files containing 000000128 events
ft970629_1345_0030S107102L.fits-> Tar-ing together the leftover raw files
a ft970629_1345_0030G200270M.fits 31K a ft970629_1345_0030G201070L.fits 31K a ft970629_1345_0030G201270M.fits 31K a ft970629_1345_0030G201370M.fits 31K a ft970629_1345_0030G201470M.fits 31K a ft970629_1345_0030G201670H.fits 31K a ft970629_1345_0030G201770H.fits 31K a ft970629_1345_0030G201870H.fits 31K a ft970629_1345_0030G202670L.fits 31K a ft970629_1345_0030G202870M.fits 31K a ft970629_1345_0030G202970M.fits 31K a ft970629_1345_0030G203070M.fits 31K a ft970629_1345_0030G203270H.fits 31K a ft970629_1345_0030G203370H.fits 31K a ft970629_1345_0030G203470H.fits 31K a ft970629_1345_0030G203670H.fits 31K a ft970629_1345_0030G203870L.fits 31K a ft970629_1345_0030G204070M.fits 31K a ft970629_1345_0030G204170M.fits 31K a ft970629_1345_0030G204270M.fits 31K a ft970629_1345_0030G204470H.fits 31K a ft970629_1345_0030G204570H.fits 31K a ft970629_1345_0030G205370L.fits 31K a ft970629_1345_0030G205570M.fits 31K a ft970629_1345_0030G205670M.fits 31K a ft970629_1345_0030G205770M.fits 31K a ft970629_1345_0030G205970H.fits 31K a ft970629_1345_0030G206170H.fits 31K a ft970629_1345_0030G206370M.fits 31K a ft970629_1345_0030G206570L.fits 31K a ft970629_1345_0030G206770H.fits 31K a ft970629_1345_0030G206870H.fits 31K a ft970629_1345_0030G206970H.fits 31K a ft970629_1345_0030G207170M.fits 31K a ft970629_1345_0030G207370H.fits 31K a ft970629_1345_0030G207770M.fits 31K a ft970629_1345_0030G208170H.fits 31K a ft970629_1345_0030G208370H.fits 31K a ft970629_1345_0030G208570L.fits 31K a ft970629_1345_0030G208770H.fits 31K a ft970629_1345_0030G208870H.fits 31K a ft970629_1345_0030G209170M.fits 31K a ft970629_1345_0030G209370H.fits 31K a ft970629_1345_0030G209470H.fits 31K a ft970629_1345_0030G209570H.fits 31K a ft970629_1345_0030G209970H.fits 31K a ft970629_1345_0030G210070H.fits 31K a ft970629_1345_0030G210170H.fits 31K a ft970629_1345_0030G210370M.fits 31K a ft970629_1345_0030G210570H.fits 31K a ft970629_1345_0030G210670H.fits 31K a ft970629_1345_0030G210770H.fits 31K a ft970629_1345_0030G211770H.fits 31K a ft970629_1345_0030G211870H.fits 31K a ft970629_1345_0030G211970H.fits 31K a ft970629_1345_0030G212170M.fits 31K a ft970629_1345_0030G212470H.fits 31K a ft970629_1345_0030G212570H.fits 31K a ft970629_1345_0030G213670H.fits 31K a ft970629_1345_0030G213770H.fits 31K a ft970629_1345_0030G213970M.fits 31K a ft970629_1345_0030G214170H.fits 31K a ft970629_1345_0030G214270H.fits 31K a ft970629_1345_0030G214370H.fits 31K a ft970629_1345_0030G214970M.fits 31K a ft970629_1345_0030G215170H.fits 31K a ft970629_1345_0030G215270H.fits 31K a ft970629_1345_0030G215370H.fits 31K a ft970629_1345_0030G215970M.fits 31K a ft970629_1345_0030G216370H.fits 31K a ft970629_1345_0030G216870H.fits 31K a ft970629_1345_0030G216970H.fits 31K a ft970629_1345_0030G217070H.fits 31K a ft970629_1345_0030G217270M.fits 31K a ft970629_1345_0030G217470H.fits 31K a ft970629_1345_0030G217570H.fits 31K a ft970629_1345_0030G217670H.fits 31K a ft970629_1345_0030G217870H.fits 31K a ft970629_1345_0030G218170L.fits 31K a ft970629_1345_0030G218370H.fits 31K a ft970629_1345_0030G218470H.fits 31K a ft970629_1345_0030G218570H.fits 31K a ft970629_1345_0030G218770H.fits 31K a ft970629_1345_0030G219170L.fits 31K a ft970629_1345_0030G219870H.fits 31K a ft970629_1345_0030G219970H.fits 31K a ft970629_1345_0030G221170H.fits 31K a ft970629_1345_0030G221270H.fits 31K a ft970629_1345_0030G221570M.fits 31K a ft970629_1345_0030G221770H.fits 31K a ft970629_1345_0030G221870H.fits 31K a ft970629_1345_0030G221970H.fits 31K a ft970629_1345_0030G222170M.fits 31K a ft970629_1345_0030G222970H.fits 31K a ft970629_1345_0030G223070H.fits 31K a ft970629_1345_0030G223270M.fits 31K a ft970629_1345_0030G223770L.fits 31K a ft970629_1345_0030G224070H.fits 31K a ft970629_1345_0030G224170H.fits 31K a ft970629_1345_0030G224270H.fits 31K a ft970629_1345_0030G224470H.fits 31K a ft970629_1345_0030G224670M.fits 31K a ft970629_1345_0030G224870L.fits 31K a ft970629_1345_0030G225170H.fits 31K a ft970629_1345_0030G225370H.fits 31K a ft970629_1345_0030G225570M.fits 31K a ft970629_1345_0030G300270M.fits 31K a ft970629_1345_0030G301070L.fits 31K a ft970629_1345_0030G301270M.fits 31K a ft970629_1345_0030G301370M.fits 31K a ft970629_1345_0030G301470M.fits 31K a ft970629_1345_0030G301670H.fits 31K a ft970629_1345_0030G301870H.fits 31K a ft970629_1345_0030G302070H.fits 31K a ft970629_1345_0030G302670L.fits 31K a ft970629_1345_0030G302870M.fits 31K a ft970629_1345_0030G302970M.fits 31K a ft970629_1345_0030G303070M.fits 31K a ft970629_1345_0030G303270H.fits 31K a ft970629_1345_0030G303370H.fits 31K a ft970629_1345_0030G303470H.fits 31K a ft970629_1345_0030G303870L.fits 31K a ft970629_1345_0030G304070M.fits 31K a ft970629_1345_0030G304170M.fits 31K a ft970629_1345_0030G304270M.fits 31K a ft970629_1345_0030G304570H.fits 31K a ft970629_1345_0030G304670H.fits 31K a ft970629_1345_0030G305370L.fits 31K a ft970629_1345_0030G305570M.fits 31K a ft970629_1345_0030G305670M.fits 31K a ft970629_1345_0030G305770M.fits 31K a ft970629_1345_0030G305970H.fits 31K a ft970629_1345_0030G306070H.fits 31K a ft970629_1345_0030G306170H.fits 31K a ft970629_1345_0030G306370M.fits 31K a ft970629_1345_0030G306570L.fits 31K a ft970629_1345_0030G306770H.fits 31K a ft970629_1345_0030G306870H.fits 31K a ft970629_1345_0030G306970H.fits 31K a ft970629_1345_0030G307170M.fits 31K a ft970629_1345_0030G307470H.fits 31K a ft970629_1345_0030G307570H.fits 31K a ft970629_1345_0030G307770M.fits 31K a ft970629_1345_0030G308170H.fits 31K a ft970629_1345_0030G308370H.fits 31K a ft970629_1345_0030G308570L.fits 31K a ft970629_1345_0030G308770H.fits 31K a ft970629_1345_0030G308870H.fits 31K a ft970629_1345_0030G308970H.fits 31K a ft970629_1345_0030G309170M.fits 31K a ft970629_1345_0030G309370H.fits 31K a ft970629_1345_0030G309470H.fits 31K a ft970629_1345_0030G309570H.fits 31K a ft970629_1345_0030G309970H.fits 31K a ft970629_1345_0030G310070H.fits 31K a ft970629_1345_0030G310370M.fits 31K a ft970629_1345_0030G310570H.fits 31K a ft970629_1345_0030G310670H.fits 31K a ft970629_1345_0030G311770H.fits 31K a ft970629_1345_0030G311870H.fits 31K a ft970629_1345_0030G312170M.fits 31K a ft970629_1345_0030G312470H.fits 31K a ft970629_1345_0030G313670H.fits 31K a ft970629_1345_0030G313770H.fits 31K a ft970629_1345_0030G313970M.fits 31K a ft970629_1345_0030G314270H.fits 31K a ft970629_1345_0030G314370H.fits 31K a ft970629_1345_0030G314970M.fits 31K a ft970629_1345_0030G315170H.fits 31K a ft970629_1345_0030G315270H.fits 31K a ft970629_1345_0030G315370H.fits 31K a ft970629_1345_0030G315970M.fits 31K a ft970629_1345_0030G316370H.fits 31K a ft970629_1345_0030G316470H.fits 31K a ft970629_1345_0030G316970H.fits 31K a ft970629_1345_0030G317070H.fits 31K a ft970629_1345_0030G317270M.fits 31K a ft970629_1345_0030G317570H.fits 31K a ft970629_1345_0030G318170L.fits 31K a ft970629_1345_0030G318370H.fits 31K a ft970629_1345_0030G318470H.fits 31K a ft970629_1345_0030G318570H.fits 31K a ft970629_1345_0030G318770H.fits 31K a ft970629_1345_0030G319170L.fits 31K a ft970629_1345_0030G319570H.fits 31K a ft970629_1345_0030G319670H.fits 31K a ft970629_1345_0030G319970H.fits 31K a ft970629_1345_0030G320070H.fits 31K a ft970629_1345_0030G320370H.fits 31K a ft970629_1345_0030G321170H.fits 31K a ft970629_1345_0030G321670M.fits 31K a ft970629_1345_0030G322270M.fits 31K a ft970629_1345_0030G323070H.fits 31K a ft970629_1345_0030G323170H.fits 31K a ft970629_1345_0030G323370M.fits 31K a ft970629_1345_0030G323870L.fits 31K a ft970629_1345_0030G324170M.fits 31K a ft970629_1345_0030G324770M.fits 31K a ft970629_1345_0030G324970L.fits 31K a ft970629_1345_0030G325270H.fits 31K a ft970629_1345_0030G325370H.fits 31K a ft970629_1345_0030G325470H.fits 31K a ft970629_1345_0030G325670M.fits 31K a ft970629_1345_0030S000401L.fits 31K a ft970629_1345_0030S004902H.fits 29K a ft970629_1345_0030S006801H.fits 37K a ft970629_1345_0030S007601H.fits 37K a ft970629_1345_0030S008201H.fits 37K a ft970629_1345_0030S009601L.fits 29K a ft970629_1345_0030S010401L.fits 31K a ft970629_1345_0030S010702M.fits 29K a ft970629_1345_0030S013402M.fits 29K a ft970629_1345_0030S100401L.fits 31K a ft970629_1345_0030S104701H.fits 37K a ft970629_1345_0030S105301H.fits 37K a ft970629_1345_0030S105701H.fits 37K a ft970629_1345_0030S106701L.fits 29K a ft970629_1345_0030S107102L.fits 31K a ft970629_1345_0030S107301L.fits 31K a ft970629_1345_0030S107602M.fits 31K a ft970629_1345_0030S109602M.fits 31K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft970629_1345.0030' is successfully opened Data Start Time is 141745525.60 (19970629 134522) Time Margin 2.0 sec included Sync error detected in 1779 th SF Sync error detected in 22397 th SF Sync error detected in 24404 th SF 'ft970629_1345.0030' EOF detected, sf=26224 Data End Time is 141870632.84 (19970701 003028) Gain History is written in ft970629_1345_0030.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft970629_1345_0030.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft970629_1345_0030.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft970629_1345_0030CMHK.fits
The sum of the selected column is 75645.000 The mean of the selected column is 100.59176 The standard deviation of the selected column is 2.4466801 The minimum of selected column is 92.000000 The maximum of selected column is 105.00000 The number of points used in calculation is 752
ASCALIN_V0.9u-> Checking if ad75071000g200270m.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000g200370l.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000g300170h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000g300270m.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000g300370l.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000101h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000102h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000112h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000202m.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000301h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000302h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000312h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000402l.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000502m.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000602l.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s000702h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100101h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100102h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100112h.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100202m.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100302l.unf is covered by attitude file
ASCALIN_V0.9u-> Checking if ad75071000s100402h.unf is covered by attitude file
ASCALIN_V0.9u
S0-HK file: ft970629_1345_0030S0HK.fits S1-HK file: ft970629_1345_0030S1HK.fits G2-HK file: ft970629_1345_0030G2HK.fits G3-HK file: ft970629_1345_0030G3HK.fits Date and time are: 1997-06-29 13:45:19 mjd=50628.573142 Orbit file name is ./frf.orbit.230 Epoch of Orbital Elements: 1997-06-23 20:00:00 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa970629_1345.0030 output FITS File: ft970629_1345_0030.mkf Total 3910 Data bins were processed.-> Checking if column TIME in ft970629_1345_0030.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 23244.142 The mean of the selected column is 25.486998 The standard deviation of the selected column is 25.672037 The minimum of selected column is 3.1125093 The maximum of selected column is 377.25116 The number of points used in calculation is 912-> Calculating statistics for S0_PIXL2
The sum of the selected column is 25518.183 The mean of the selected column is 28.134712 The standard deviation of the selected column is 30.170124 The minimum of selected column is 3.7777889 The maximum of selected column is 462.43890 The number of points used in calculation is 907-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<102.5 )&& (S0_PIXL2>0.0 && S0_PIXL2<118.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.41E+05 349504 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
325925 231227 0 94698 0 0
Writing events file
231227 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
325925 231227 0 94698 0 0
in 29033.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 231227
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 62 130226
Flickering pixels iter, pixels & cnts : 1 38 2726
cleaning chip # 2
Hot pixels & counts : 40 94091
Flickering pixels iter, pixels & cnts : 1 43 1970
cleaning chip # 3
Number of pixels rejected : 183
Number of (internal) image counts : 231227
Number of image cts rejected (N, %) : 22901399.04
By chip : 0 1 2 3
Pixels rejected : 0 100 83 0
Image counts : 0 134185 97042 0
Image cts rejected: 0 132952 96061 0
Image cts rej (%) : 0.00 99.08 98.99 0.00
filtering data...
Total counts : 0 134185 97042 0
Total cts rejected: 0 132952 96061 0
Total cts rej (%) : 0.00 99.08 98.99 0.00
Number of clean counts accepted : 2214
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 183
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000102h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000102h.evt use_events=no
Wrote cleaned events file to ad75071000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad75071000s000112h.unf into ad75071000s000112h.evtThe sum of the selected column is 23244.142 The mean of the selected column is 25.486998 The standard deviation of the selected column is 25.672037 The minimum of selected column is 3.1125093 The maximum of selected column is 377.25116 The number of points used in calculation is 912-> Calculating statistics for S0_PIXL2
The sum of the selected column is 25518.183 The mean of the selected column is 28.134712 The standard deviation of the selected column is 30.170124 The minimum of selected column is 3.7777889 The maximum of selected column is 462.43890 The number of points used in calculation is 907-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<102.5 )&& (S0_PIXL2>0.0 && S0_PIXL2<118.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 14:41:49 0.41E+05 351164 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000112h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
328389 232845 0 95544 0 0
Writing events file
232845 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
328389 232845 0 95544 0 0
in 29033.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 232845
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 62 130761
Flickering pixels iter, pixels & cnts : 1 38 2736
cleaning chip # 2
Hot pixels & counts : 40 94906
Flickering pixels iter, pixels & cnts : 1 43 1954
cleaning chip # 3
Number of pixels rejected : 183
Number of (internal) image counts : 232845
Number of image cts rejected (N, %) : 23035798.93
By chip : 0 1 2 3
Pixels rejected : 0 100 83 0
Image counts : 0 134874 97971 0
Image cts rejected: 0 133497 96860 0
Image cts rej (%) : 0.00 98.98 98.87 0.00
filtering data...
Total counts : 0 134874 97971 0
Total cts rejected: 0 133497 96860 0
Total cts rej (%) : 0.00 98.98 98.87 0.00
Number of clean counts accepted : 2488
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 183
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000112h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad75071000s000112h.evt use_events=no
Wrote cleaned events file to ad75071000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad75071000s000202m.unf into ad75071000s000202m.evtThe sum of the selected column is 10618.937 The mean of the selected column is 21.111207 The standard deviation of the selected column is 8.3461765 The minimum of selected column is 2.8636997 The maximum of selected column is 68.593979 The number of points used in calculation is 503-> Calculating statistics for S0_PIXL2
The sum of the selected column is 12166.995 The mean of the selected column is 24.237042 The standard deviation of the selected column is 11.058461 The minimum of selected column is 5.0001106 The maximum of selected column is 78.031494 The number of points used in calculation is 502-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<46.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<57.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.24E+05 207224 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
193254 123880 0 69374 0 0
Writing events file
123880 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
193254 123880 0 69374 0 0
in 15560.92 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 123880
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 59 69047
Flickering pixels iter, pixels & cnts : 1 35 2052
cleaning chip # 2
Hot pixels & counts : 41 50613
Flickering pixels iter, pixels & cnts : 1 35 992
cleaning chip # 3
Number of pixels rejected : 170
Number of (internal) image counts : 123880
Number of image cts rejected (N, %) : 12270499.05
By chip : 0 1 2 3
Pixels rejected : 0 94 76 0
Image counts : 0 71755 52125 0
Image cts rejected: 0 71099 51605 0
Image cts rej (%) : 0.00 99.09 99.00 0.00
filtering data...
Total counts : 0 71755 52125 0
Total cts rejected: 0 71099 51605 0
Total cts rej (%) : 0.00 99.09 99.00 0.00
Number of clean counts accepted : 1176
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 170
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000202m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000202m.evt use_events=no
Wrote cleaned events file to ad75071000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad75071000s000301h.unf because of modeThe sum of the selected column is 439.09510 The mean of the selected column is 33.776546 The standard deviation of the selected column is 10.285388 The minimum of selected column is 19.562561 The maximum of selected column is 51.406410 The number of points used in calculation is 13-> Calculating statistics for S0_PIXL2
The sum of the selected column is 373.96990 The mean of the selected column is 28.766916 The standard deviation of the selected column is 9.6894496 The minimum of selected column is 12.531290 The maximum of selected column is 47.875149 The number of points used in calculation is 13-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>2.9 && S0_PIXL1<64.6 )&& (S0_PIXL2>0.0 && S0_PIXL2<57.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.45E+04 40900 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
33926 3250 0 30676 0 0
Writing events file
3250 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
33926 3250 0 30676 0 0
in 386.69 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3250
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 51 1921
Flickering pixels iter, pixels & cnts : 1 22 163
cleaning chip # 2
Hot pixels & counts : 32 1036
Flickering pixels iter, pixels & cnts : 1 10 62
cleaning chip # 3
Number of pixels rejected : 115
Number of (internal) image counts : 3250
Number of image cts rejected (N, %) : 318297.91
By chip : 0 1 2 3
Pixels rejected : 0 73 42 0
Image counts : 0 2130 1120 0
Image cts rejected: 0 2084 1098 0
Image cts rej (%) : 0.00 97.84 98.04 0.00
filtering data...
Total counts : 0 2130 1120 0
Total cts rejected: 0 2084 1098 0
Total cts rej (%) : 0.00 97.84 98.04 0.00
Number of clean counts accepted : 68
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 115
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000302h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000302h.evt use_events=no
Wrote cleaned events file to ad75071000s000302h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad75071000s000312h.unf into ad75071000s000312h.evtThe sum of the selected column is 439.09510 The mean of the selected column is 33.776546 The standard deviation of the selected column is 10.285388 The minimum of selected column is 19.562561 The maximum of selected column is 51.406410 The number of points used in calculation is 13-> Calculating statistics for S0_PIXL2
The sum of the selected column is 373.96990 The mean of the selected column is 28.766916 The standard deviation of the selected column is 9.6894496 The minimum of selected column is 12.531290 The maximum of selected column is 47.875149 The number of points used in calculation is 13-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>2.9 && S0_PIXL1<64.6 )&& (S0_PIXL2>0.0 && S0_PIXL2<57.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 13:45:17 0.45E+04 41470 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000312h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
34627 3284 0 31343 0 0
Writing events file
3284 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34627 3284 0 31343 0 0
in 386.69 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3284
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 51 1930
Flickering pixels iter, pixels & cnts : 1 23 168
cleaning chip # 2
Hot pixels & counts : 32 1048
Flickering pixels iter, pixels & cnts : 1 10 63
cleaning chip # 3
Number of pixels rejected : 116
Number of (internal) image counts : 3284
Number of image cts rejected (N, %) : 320997.72
By chip : 0 1 2 3
Pixels rejected : 0 74 42 0
Image counts : 0 2145 1139 0
Image cts rejected: 0 2098 1111 0
Image cts rej (%) : 0.00 97.81 97.54 0.00
filtering data...
Total counts : 0 2145 1139 0
Total cts rejected: 0 2098 1111 0
Total cts rej (%) : 0.00 97.81 97.54 0.00
Number of clean counts accepted : 75
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 116
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000312h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad75071000s000312h.evt use_events=no
Wrote cleaned events file to ad75071000s000312h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad75071000s000402l.unf into ad75071000s000402l.evtThe sum of the selected column is 403.15821 The mean of the selected column is 25.197388 The standard deviation of the selected column is 6.6490158 The minimum of selected column is 15.281357 The maximum of selected column is 37.594009 The number of points used in calculation is 16-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>5.2 && S0_PIXL2<45.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 14:24:41 0.12E+05 87731 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000402l.unf
extractor v3.42 9 Oct 1998
No events selected from file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.00
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000402l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000402l.evt use_events=no
Wrote cleaned events file to ad75071000s000402l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad75071000s000402l.evt since it contains 0 eventsThe sum of the selected column is 426.22445 The mean of the selected column is 21.311223 The standard deviation of the selected column is 5.4059049 The minimum of selected column is 16.093801 The maximum of selected column is 35.813137 The number of points used in calculation is 20-> Calculating statistics for S0_PIXL2
The sum of the selected column is 466.06809 The mean of the selected column is 24.529899 The standard deviation of the selected column is 13.831872 The minimum of selected column is 10.343934 The maximum of selected column is 76.312737 The number of points used in calculation is 19-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>5 && S0_PIXL1<37.5 )&& (S0_PIXL2>0.0 && S0_PIXL2<66 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.80E+04 34336 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
24616 4373 0 20243 0 0
Writing events file
4373 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24616 4373 0 20243 0 0
in 528.52 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 4373
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 53 2516
Flickering pixels iter, pixels & cnts : 1 26 208
cleaning chip # 2
Hot pixels & counts : 34 1431
Flickering pixels iter, pixels & cnts : 1 25 146
cleaning chip # 3
Number of pixels rejected : 138
Number of (internal) image counts : 4373
Number of image cts rejected (N, %) : 430198.35
By chip : 0 1 2 3
Pixels rejected : 0 79 59 0
Image counts : 0 2757 1616 0
Image cts rejected: 0 2724 1577 0
Image cts rej (%) : 0.00 98.80 97.59 0.00
filtering data...
Total counts : 0 2757 1616 0
Total cts rejected: 0 2724 1577 0
Total cts rej (%) : 0.00 98.80 97.59 0.00
Number of clean counts accepted : 72
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 138
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000502m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000502m.evt use_events=no
Wrote cleaned events file to ad75071000s000502m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad75071000s000602l.unf into ad75071000s000602l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 15:06:17 0.12E+05 17331 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000602l.unf
extractor v3.42 9 Oct 1998
No events selected from file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.00
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000602l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000602l.evt use_events=no
Wrote cleaned events file to ad75071000s000602l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad75071000s000602l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.48E+02 1767 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
852 404 0 448 0 0
Writing events file
404 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
852 404 0 448 0 0
in 14.28 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 404
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 404
Number of image cts rejected (N, %) : 0 0.00
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 346 58 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 346 58 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 404
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s000702h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad75071000s000702h.evt use_events=no
Wrote cleaned events file to ad75071000s000702h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad75071000s100101h.unf because of modeThe sum of the selected column is 36212.410 The mean of the selected column is 39.233380 The standard deviation of the selected column is 32.777387 The minimum of selected column is 7.4625220 The maximum of selected column is 462.37640 The number of points used in calculation is 923-> Calculating statistics for S1_PIXL2
The sum of the selected column is 35138.519 The mean of the selected column is 38.277253 The standard deviation of the selected column is 30.719498 The minimum of selected column is 5.7222390 The maximum of selected column is 430.93881 The number of points used in calculation is 918-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<137.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<130.4 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.46E+05 715420 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s100102h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
653004 431359 0 221645 0 0
Writing events file
431359 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
653004 431359 0 221645 0 0
in 29330.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 431359
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 78 201457
Flickering pixels iter, pixels & cnts : 1 72 6930
cleaning chip # 2
Hot pixels & counts : 86 213499
Flickering pixels iter, pixels & cnts : 1 86 6993
Flickering pixels iter, pixels & cnts : 2 1 3
cleaning chip # 3
Number of pixels rejected : 323
Number of (internal) image counts : 431359
Number of image cts rejected (N, %) : 42888299.43
By chip : 0 1 2 3
Pixels rejected : 0 150 173 0
Image counts : 0 209593 221766 0
Image cts rejected: 0 208387 220495 0
Image cts rej (%) : 0.00 99.42 99.43 0.00
filtering data...
Total counts : 0 209593 221766 0
Total cts rejected: 0 208387 220495 0
Total cts rej (%) : 0.00 99.42 99.43 0.00
Number of clean counts accepted : 2477
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 323
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s100102h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad75071000s100102h.evt use_events=no
Wrote cleaned events file to ad75071000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad75071000s100112h.unf into ad75071000s100112h.evtThe sum of the selected column is 36212.410 The mean of the selected column is 39.233380 The standard deviation of the selected column is 32.777387 The minimum of selected column is 7.4625220 The maximum of selected column is 462.37640 The number of points used in calculation is 923-> Calculating statistics for S1_PIXL2
The sum of the selected column is 35138.519 The mean of the selected column is 38.277253 The standard deviation of the selected column is 30.719498 The minimum of selected column is 5.7222390 The maximum of selected column is 430.93881 The number of points used in calculation is 918-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<137.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<130.4 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 13:45:17 0.46E+05 718166 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s100112h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
663969 438057 0 225912 0 0
Writing events file
438057 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
663969 438057 0 225912 0 0
in 29330.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 438057
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 78 205518
Flickering pixels iter, pixels & cnts : 1 72 7324
cleaning chip # 2
Hot pixels & counts : 87 215816
Flickering pixels iter, pixels & cnts : 1 85 6603
Flickering pixels iter, pixels & cnts : 2 1 4
cleaning chip # 3
Number of pixels rejected : 323
Number of (internal) image counts : 438057
Number of image cts rejected (N, %) : 43526599.36
By chip : 0 1 2 3
Pixels rejected : 0 150 173 0
Image counts : 0 214193 223864 0
Image cts rejected: 0 212842 222423 0
Image cts rej (%) : 0.00 99.37 99.36 0.00
filtering data...
Total counts : 0 214193 223864 0
Total cts rejected: 0 212842 222423 0
Total cts rej (%) : 0.00 99.37 99.36 0.00
Number of clean counts accepted : 2792
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 323
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s100112h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad75071000s100112h.evt use_events=no
Wrote cleaned events file to ad75071000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad75071000s100202m.unf into ad75071000s100202m.evtThe sum of the selected column is 17381.901 The mean of the selected column is 33.234991 The standard deviation of the selected column is 12.724663 The minimum of selected column is 6.3524132 The maximum of selected column is 104.62533 The number of points used in calculation is 523-> Calculating statistics for S1_PIXL2
The sum of the selected column is 16887.909 The mean of the selected column is 32.476748 The standard deviation of the selected column is 11.990450 The minimum of selected column is 4.7387409 The maximum of selected column is 90.500275 The number of points used in calculation is 520-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<71.4 )&& (S1_PIXL2>0.0 && S1_PIXL2<68.4 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.32E+05 459114 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s100202m.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
416611 241447 0 175164 0 0
Writing events file
241447 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
416611 241447 0 175164 0 0
in 16288.08 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 241447
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 78 113074
Flickering pixels iter, pixels & cnts : 1 67 4269
cleaning chip # 2
Hot pixels & counts : 85 118728
Flickering pixels iter, pixels & cnts : 1 65 3973
cleaning chip # 3
Number of pixels rejected : 295
Number of (internal) image counts : 241447
Number of image cts rejected (N, %) : 24004499.42
By chip : 0 1 2 3
Pixels rejected : 0 145 150 0
Image counts : 0 118018 123429 0
Image cts rejected: 0 117343 122701 0
Image cts rej (%) : 0.00 99.43 99.41 0.00
filtering data...
Total counts : 0 118018 123429 0
Total cts rejected: 0 117343 122701 0
Total cts rej (%) : 0.00 99.43 99.41 0.00
Number of clean counts accepted : 1403
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 295
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s100202m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad75071000s100202m.evt use_events=no
Wrote cleaned events file to ad75071000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad75071000s100302l.unf into ad75071000s100302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0)&& (S1_PIXL2>0) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 14:24:41 0.24E+05 123973 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s100302l.unf
extractor v3.42 9 Oct 1998
No events selected from file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.00
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s100302l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad75071000s100302l.evt use_events=no
Wrote cleaned events file to ad75071000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad75071000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0)&& (S1_PIXL2>0) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 02:13:49 0.60E+02 1865 0110
Processing file: /data/data22/seq_proc/75071000.004/ad75071000s100402h.unf
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1031 401 0 630 0 0
Writing events file
401 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1031 401 0 630 0 0
in 14.28 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/75071000.004/screen_in_event.xsl
reading data file: /data/data22/seq_proc/75071000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 401
Total counts in chip images : 400
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 400
Number of image cts rejected (N, %) : 0 0.00
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 271 129 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 272 129 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 401
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000s100402h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad75071000s100402h.evt use_events=no
Wrote cleaned events file to ad75071000s100402h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad75071000g200170h.unf into ad75071000g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.unf
Total Good Bad: Region Time Phase Cut
33076 9223 20835 3018 0 0
Writing events file
9223 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
33076 9223 20835 3018 0 0
in 30643.71 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
9223 7848 1375
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g200170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad75071000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad75071000g200270m.unf into ad75071000g200270m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 21409 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.unf
Total Good Bad: Region Time Phase Cut
21409 5271 13610 2528 0 0
Writing events file
5271 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21409 5271 13610 2528 0 0
in 18297.48 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5271 4527 744
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g200270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad75071000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad75071000g200370l.unf into ad75071000g200370l.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 12310 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.unf
Total Good Bad: Region Time Phase Cut
12310 412 8472 3426 0 0
Writing events file
412 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12310 412 8472 3426 0 0
in 1358.43 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
412 363 49
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g200370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad75071000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad75071000g300170h.unf into ad75071000g300170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.unf
Total Good Bad: Region Time Phase Cut
30570 9902 17459 3209 0 0
Writing events file
9902 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30570 9902 17459 3209 0 0
in 30645.71 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
9902 8431 1471
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g300170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad75071000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad75071000g300270m.unf into ad75071000g300270m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 19495 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.unf
Total Good Bad: Region Time Phase Cut
19495 5577 11223 2695 0 0
Writing events file
5577 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19495 5577 11223 2695 0 0
in 18281.48 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5577 4787 790
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g300270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad75071000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad75071000g300370l.unf into ad75071000g300370l.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 11366 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.unf
Total Good Bad: Region Time Phase Cut
11366 412 7204 3750 0 0
Writing events file
412 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11366 412 7204 3750 0 0
in 1358.43 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
412 347 65
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!screen:ASCA > read events ad75071000g300370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/aps/tools/ftools/ftools.4.2/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad75071000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad75071000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4781
Mean RA/DEC/ROLL : 13.0372 -29.1013 289.4781
Pnt RA/DEC/ROLL : 12.8859 -29.3446 289.4781
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 47
Total GTI (secs) : 30643.717
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 5015.82 5015.82
20 Percent Complete: Total/live time: 6724.84 6724.84
30 Percent Complete: Total/live time: 9627.31 9627.31
40 Percent Complete: Total/live time: 13042.29 13042.29
50 Percent Complete: Total/live time: 15883.88 15883.88
60 Percent Complete: Total/live time: 19118.05 19118.05
70 Percent Complete: Total/live time: 22290.17 22290.17
80 Percent Complete: Total/live time: 28099.76 28099.76
90 Percent Complete: Total/live time: 28099.76 28099.76
100 Percent Complete: Total/live time: 30643.72 30643.72
Number of attitude steps used: 64
Number of attitude steps avail: 83161
Mean RA/DEC pixel offset: -9.2487 -3.4639
writing expo file: ad75071000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g200170h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g200170h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 7711 137 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7848 7711 137 0 0 0
in 30643.71 seconds
Image has 7711 counts for 0.2516 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 3359 137 0 0 4352
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7848 3359 137 0 0 4352
in 30643.71 seconds
Image has 3359 counts for 0.1096 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 4376 137 0 0 3335
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7848 4376 137 0 0 3335
in 30643.71 seconds
Image has 4376 counts for 0.1428 counts/sec
Command not found; type ? for a command listing
!ad75071000g200170h:ASCA >
!ad75071000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g200170h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g200170h:ASCA > read events ad75071000g200170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g200170h:ASCA-GIS2-PH > set image sky
!ad75071000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad75071000g200170h:ASCA-GIS2-PH > extract image
!ad75071000g200170h:ASCA-GIS2-PH > save image outfile=ad75071000g200170h.img
Wrote image to file ad75071000g200170h.img
!ad75071000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad75071000g200170h:ASCA-GIS2-PH > extract image
!ad75071000g200170h:ASCA-GIS2-PH > save image outfile=ad75071000g200170h_lo.img
Wrote image to file ad75071000g200170h_lo.img
!ad75071000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad75071000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g200170h:ASCA-GIS2-PH > extract image
!ad75071000g200170h:ASCA-GIS2-PH > save image outfile=ad75071000g200170h_hi.img
Wrote image to file ad75071000g200170h_hi.img
!ad75071000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad75071000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad75071000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4799
Mean RA/DEC/ROLL : 13.0369 -29.1021 289.4799
Pnt RA/DEC/ROLL : 12.8941 -29.3438 289.4799
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 27
Total GTI (secs) : 18297.479
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2049.11 2049.11
20 Percent Complete: Total/live time: 4104.11 4104.11
30 Percent Complete: Total/live time: 5849.10 5849.10
40 Percent Complete: Total/live time: 7681.06 7681.06
50 Percent Complete: Total/live time: 9352.16 9352.16
60 Percent Complete: Total/live time: 11357.01 11357.01
70 Percent Complete: Total/live time: 12996.98 12996.98
80 Percent Complete: Total/live time: 15920.90 15920.90
90 Percent Complete: Total/live time: 16713.88 16713.88
100 Percent Complete: Total/live time: 18297.48 18297.48
Number of attitude steps used: 55
Number of attitude steps avail: 31688
Mean RA/DEC pixel offset: -14.0613 -4.0373
writing expo file: ad75071000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g200270m.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g200270m
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 4453 74 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4527 4453 74 0 0 0
in 18297.48 seconds
Image has 4453 counts for 0.2434 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 1922 74 0 0 2531
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4527 1922 74 0 0 2531
in 18297.48 seconds
Image has 1922 counts for 0.1050 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 2538 74 0 0 1915
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4527 2538 74 0 0 1915
in 18297.48 seconds
Image has 2538 counts for 0.1387 counts/sec
Command not found; type ? for a command listing
!ad75071000g200270m:ASCA >
!ad75071000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g200270m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g200270m:ASCA > read events ad75071000g200270m.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g200270m:ASCA-GIS2-PH > set image sky
!ad75071000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad75071000g200270m:ASCA-GIS2-PH > extract image
!ad75071000g200270m:ASCA-GIS2-PH > save image outfile=ad75071000g200270m.img
Wrote image to file ad75071000g200270m.img
!ad75071000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad75071000g200270m:ASCA-GIS2-PH > extract image
!ad75071000g200270m:ASCA-GIS2-PH > save image outfile=ad75071000g200270m_lo.img
Wrote image to file ad75071000g200270m_lo.img
!ad75071000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad75071000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g200270m:ASCA-GIS2-PH > extract image
!ad75071000g200270m:ASCA-GIS2-PH > save image outfile=ad75071000g200270m_hi.img
Wrote image to file ad75071000g200270m_hi.img
!ad75071000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad75071000g200370l.expo
ASCAEXPO_V0.9b
reading data file: ad75071000g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4800
Mean RA/DEC/ROLL : 13.0350 -29.1037 289.4800
Pnt RA/DEC/ROLL : 13.0440 -29.0586 289.4800
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 11
Total GTI (secs) : 1358.432
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 557.00 557.00
20 Percent Complete: Total/live time: 557.00 557.00
30 Percent Complete: Total/live time: 1024.00 1024.00
40 Percent Complete: Total/live time: 1024.00 1024.00
50 Percent Complete: Total/live time: 1029.10 1029.10
60 Percent Complete: Total/live time: 1029.10 1029.10
70 Percent Complete: Total/live time: 1032.10 1032.10
80 Percent Complete: Total/live time: 1112.25 1112.25
90 Percent Complete: Total/live time: 1256.29 1256.29
100 Percent Complete: Total/live time: 1358.43 1358.43
Number of attitude steps used: 20
Number of attitude steps avail: 2385
Mean RA/DEC pixel offset: -8.6839 -3.5619
writing expo file: ad75071000g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g200370l.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g200370l
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 363 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 362 1 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
363 362 1 0 0 0
in 1358.43 seconds
Image has 362 counts for 0.2665 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 153 1 0 0 209
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
363 153 1 0 0 209
in 1358.43 seconds
Image has 153 counts for 0.1126 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 211 1 0 0 151
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
363 211 1 0 0 151
in 1358.43 seconds
Image has 211 counts for 0.1553 counts/sec
Command not found; type ? for a command listing
!ad75071000g200370l:ASCA >
!ad75071000g200370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g200370l:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g200370l:ASCA > read events ad75071000g200370l.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g200370l:ASCA-GIS2-PH > set image sky
!ad75071000g200370l:ASCA-GIS2-PH > filter region corner_point.reg
!ad75071000g200370l:ASCA-GIS2-PH > extract image
!ad75071000g200370l:ASCA-GIS2-PH > save image outfile=ad75071000g200370l.img
Wrote image to file ad75071000g200370l.img
!ad75071000g200370l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad75071000g200370l:ASCA-GIS2-PH > extract image
!ad75071000g200370l:ASCA-GIS2-PH > save image outfile=ad75071000g200370l_lo.img
Wrote image to file ad75071000g200370l_lo.img
!ad75071000g200370l:ASCA-GIS2-PH > clear pha_cut
!ad75071000g200370l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g200370l:ASCA-GIS2-PH > extract image
!ad75071000g200370l:ASCA-GIS2-PH > save image outfile=ad75071000g200370l_hi.img
Wrote image to file ad75071000g200370l_hi.img
!ad75071000g200370l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad75071000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad75071000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4815
Mean RA/DEC/ROLL : 13.0305 -29.0772 289.4815
Pnt RA/DEC/ROLL : 12.8926 -29.3687 289.4815
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 46
Total GTI (secs) : 30645.719
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 5015.82 5015.82
20 Percent Complete: Total/live time: 6724.84 6724.84
30 Percent Complete: Total/live time: 9627.31 9627.31
40 Percent Complete: Total/live time: 13042.29 13042.29
50 Percent Complete: Total/live time: 15883.88 15883.88
60 Percent Complete: Total/live time: 19118.05 19118.05
70 Percent Complete: Total/live time: 22290.17 22290.17
80 Percent Complete: Total/live time: 28097.76 28097.76
90 Percent Complete: Total/live time: 28097.76 28097.76
100 Percent Complete: Total/live time: 30645.72 30645.72
Number of attitude steps used: 64
Number of attitude steps avail: 83161
Mean RA/DEC pixel offset: 2.6412 -2.2828
writing expo file: ad75071000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g300170h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g300170h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 8299 132 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8431 8299 132 0 0 0
in 30645.71 seconds
Image has 8299 counts for 0.2708 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 3633 132 0 0 4666
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8431 3633 132 0 0 4666
in 30645.71 seconds
Image has 3633 counts for 0.1185 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 4688 132 0 0 3611
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8431 4688 132 0 0 3611
in 30645.71 seconds
Image has 4688 counts for 0.1530 counts/sec
Command not found; type ? for a command listing
!ad75071000g300170h:ASCA >
!ad75071000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g300170h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g300170h:ASCA > read events ad75071000g300170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g300170h:ASCA-GIS3-PH > set image sky
!ad75071000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad75071000g300170h:ASCA-GIS3-PH > extract image
!ad75071000g300170h:ASCA-GIS3-PH > save image outfile=ad75071000g300170h.img
Wrote image to file ad75071000g300170h.img
!ad75071000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad75071000g300170h:ASCA-GIS3-PH > extract image
!ad75071000g300170h:ASCA-GIS3-PH > save image outfile=ad75071000g300170h_lo.img
Wrote image to file ad75071000g300170h_lo.img
!ad75071000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad75071000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g300170h:ASCA-GIS3-PH > extract image
!ad75071000g300170h:ASCA-GIS3-PH > save image outfile=ad75071000g300170h_hi.img
Wrote image to file ad75071000g300170h_hi.img
!ad75071000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad75071000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad75071000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4833
Mean RA/DEC/ROLL : 13.0299 -29.0783 289.4833
Pnt RA/DEC/ROLL : 12.9008 -29.3680 289.4833
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 28
Total GTI (secs) : 18281.480
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2049.11 2049.11
20 Percent Complete: Total/live time: 4104.11 4104.11
30 Percent Complete: Total/live time: 5849.10 5849.10
40 Percent Complete: Total/live time: 7681.06 7681.06
50 Percent Complete: Total/live time: 9352.16 9352.16
60 Percent Complete: Total/live time: 11357.01 11357.01
70 Percent Complete: Total/live time: 12980.98 12980.98
80 Percent Complete: Total/live time: 15904.90 15904.90
90 Percent Complete: Total/live time: 16697.88 16697.88
100 Percent Complete: Total/live time: 18281.48 18281.48
Number of attitude steps used: 55
Number of attitude steps avail: 31688
Mean RA/DEC pixel offset: 3.1115 -2.5137
writing expo file: ad75071000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g300270m.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g300270m
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 4712 75 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4787 4712 75 0 0 0
in 18281.48 seconds
Image has 4712 counts for 0.2577 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 2042 75 0 0 2670
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4787 2042 75 0 0 2670
in 18281.48 seconds
Image has 2042 counts for 0.1117 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 2680 75 0 0 2032
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4787 2680 75 0 0 2032
in 18281.48 seconds
Image has 2680 counts for 0.1466 counts/sec
Command not found; type ? for a command listing
!ad75071000g300270m:ASCA >
!ad75071000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g300270m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g300270m:ASCA > read events ad75071000g300270m.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g300270m:ASCA-GIS3-PH > set image sky
!ad75071000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad75071000g300270m:ASCA-GIS3-PH > extract image
!ad75071000g300270m:ASCA-GIS3-PH > save image outfile=ad75071000g300270m.img
Wrote image to file ad75071000g300270m.img
!ad75071000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad75071000g300270m:ASCA-GIS3-PH > extract image
!ad75071000g300270m:ASCA-GIS3-PH > save image outfile=ad75071000g300270m_lo.img
Wrote image to file ad75071000g300270m_lo.img
!ad75071000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad75071000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g300270m:ASCA-GIS3-PH > extract image
!ad75071000g300270m:ASCA-GIS3-PH > save image outfile=ad75071000g300270m_hi.img
Wrote image to file ad75071000g300270m_hi.img
!ad75071000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad75071000g300370l.expo
ASCAEXPO_V0.9b
reading data file: ad75071000g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4833
Mean RA/DEC/ROLL : 13.0283 -29.0795 289.4833
Pnt RA/DEC/ROLL : 13.0508 -29.0827 289.4833
Image rebin factor : 1
Attitude Records : 104808
GTI intervals : 11
Total GTI (secs) : 1358.432
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 557.00 557.00
20 Percent Complete: Total/live time: 557.00 557.00
30 Percent Complete: Total/live time: 1024.00 1024.00
40 Percent Complete: Total/live time: 1024.00 1024.00
50 Percent Complete: Total/live time: 1029.10 1029.10
60 Percent Complete: Total/live time: 1029.10 1029.10
70 Percent Complete: Total/live time: 1032.10 1032.10
80 Percent Complete: Total/live time: 1112.25 1112.25
90 Percent Complete: Total/live time: 1256.29 1256.29
100 Percent Complete: Total/live time: 1358.43 1358.43
Number of attitude steps used: 20
Number of attitude steps avail: 2385
Mean RA/DEC pixel offset: 2.7909 -2.4220
writing expo file: ad75071000g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000g300370l.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000g300370l
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 347 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 341 6 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
347 341 6 0 0 0
in 1358.43 seconds
Image has 341 counts for 0.2510 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 149 6 0 0 192
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
347 149 6 0 0 192
in 1358.43 seconds
Image has 149 counts for 0.1097 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 193 6 0 0 148
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
347 193 6 0 0 148
in 1358.43 seconds
Image has 193 counts for 0.1421 counts/sec
Command not found; type ? for a command listing
!ad75071000g300370l:ASCA >
!ad75071000g300370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000g300370l:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000g300370l:ASCA > read events ad75071000g300370l.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000g300370l:ASCA-GIS3-PH > set image sky
!ad75071000g300370l:ASCA-GIS3-PH > filter region corner_point.reg
!ad75071000g300370l:ASCA-GIS3-PH > extract image
!ad75071000g300370l:ASCA-GIS3-PH > save image outfile=ad75071000g300370l.img
Wrote image to file ad75071000g300370l.img
!ad75071000g300370l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad75071000g300370l:ASCA-GIS3-PH > extract image
!ad75071000g300370l:ASCA-GIS3-PH > save image outfile=ad75071000g300370l_lo.img
Wrote image to file ad75071000g300370l_lo.img
!ad75071000g300370l:ASCA-GIS3-PH > clear pha_cut
!ad75071000g300370l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad75071000g300370l:ASCA-GIS3-PH > extract image
!ad75071000g300370l:ASCA-GIS3-PH > save image outfile=ad75071000g300370l_hi.img
Wrote image to file ad75071000g300370l_hi.img
!ad75071000g300370l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad75071000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4897
Mean RA/DEC/ROLL : 13.0161 -29.0965 289.4897
Pnt RA/DEC/ROLL : 13.0654 -29.0650 289.4897
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 183
GTI intervals : 43
Total GTI (secs) : 29033.725
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 5285.93 5285.93
20 Percent Complete: Total/live time: 6213.93 6213.93
30 Percent Complete: Total/live time: 9003.82 9003.82
40 Percent Complete: Total/live time: 12403.15 12403.15
50 Percent Complete: Total/live time: 15049.71 15049.71
60 Percent Complete: Total/live time: 20883.44 20883.44
70 Percent Complete: Total/live time: 20883.44 20883.44
80 Percent Complete: Total/live time: 24460.52 24460.52
90 Percent Complete: Total/live time: 27154.82 27154.82
100 Percent Complete: Total/live time: 29033.73 29033.73
Number of attitude steps used: 52
Number of attitude steps avail: 84359
Mean RA/DEC pixel offset: -28.6744 -93.4458
writing expo file: ad75071000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s000102h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s000102h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 2214 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2214 2214 0 0 0 0
in 29033.72 seconds
Image has 2214 counts for 7.6256E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 1020 0 0 0 1194
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2214 1020 0 0 0 1194
in 29033.72 seconds
Image has 1020 counts for 3.5132E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 1196 0 0 0 1018
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2214 1196 0 0 0 1018
in 29033.72 seconds
Image has 1196 counts for 4.1193E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s000102h:ASCA >
!ad75071000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s000102h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s000102h:ASCA > read events ad75071000s000102h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad75071000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad75071000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000102h.img
Wrote image to file ad75071000s000102h.img
!ad75071000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad75071000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000102h_lo.img
Wrote image to file ad75071000s000102h_lo.img
!ad75071000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad75071000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000102h_hi.img
Wrote image to file ad75071000s000102h_hi.img
!ad75071000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4897
Mean RA/DEC/ROLL : 13.0176 -29.0935 289.4897
Pnt RA/DEC/ROLL : 12.9079 -29.3625 289.4897
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 170
GTI intervals : 42
Total GTI (secs) : 15560.920
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1713.10 1713.10
20 Percent Complete: Total/live time: 3769.97 3769.97
30 Percent Complete: Total/live time: 5539.01 5539.01
40 Percent Complete: Total/live time: 6979.00 6979.00
50 Percent Complete: Total/live time: 7993.99 7993.99
60 Percent Complete: Total/live time: 11877.50 11877.50
70 Percent Complete: Total/live time: 11877.50 11877.50
80 Percent Complete: Total/live time: 12860.98 12860.98
90 Percent Complete: Total/live time: 14708.08 14708.08
100 Percent Complete: Total/live time: 15560.92 15560.92
Number of attitude steps used: 50
Number of attitude steps avail: 34685
Mean RA/DEC pixel offset: -26.7002 -97.2862
writing expo file: ad75071000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s000202m.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s000202m
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 1176 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1176 1176 0 0 0 0
in 15560.92 seconds
Image has 1176 counts for 7.5574E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 555 0 0 0 621
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1176 555 0 0 0 621
in 15560.92 seconds
Image has 555 counts for 3.5666E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 621 0 0 0 555
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1176 621 0 0 0 555
in 15560.92 seconds
Image has 621 counts for 3.9908E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s000202m:ASCA >
!ad75071000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s000202m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s000202m:ASCA > read events ad75071000s000202m.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad75071000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad75071000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000202m.img
Wrote image to file ad75071000s000202m.img
!ad75071000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad75071000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000202m_lo.img
Wrote image to file ad75071000s000202m_lo.img
!ad75071000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad75071000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000202m_hi.img
Wrote image to file ad75071000s000202m_hi.img
!ad75071000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s000302h.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s000302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4880
Mean RA/DEC/ROLL : 13.0338 -29.0626 289.4880
Pnt RA/DEC/ROLL : 12.9058 -29.3517 289.4880
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 115
GTI intervals : 5
Total GTI (secs) : 386.686
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 58.07 58.07
20 Percent Complete: Total/live time: 116.18 116.18
30 Percent Complete: Total/live time: 206.32 206.32
40 Percent Complete: Total/live time: 206.32 206.32
50 Percent Complete: Total/live time: 206.44 206.44
60 Percent Complete: Total/live time: 296.47 296.47
70 Percent Complete: Total/live time: 296.47 296.47
80 Percent Complete: Total/live time: 386.69 386.69
100 Percent Complete: Total/live time: 386.69 386.69
Number of attitude steps used: 8
Number of attitude steps avail: 10624
Mean RA/DEC pixel offset: -28.7081 -80.5328
writing expo file: ad75071000s000302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s000302h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s000302h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.39E+03 68 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.evt
Total Good Bad: Region Time Phase Cut
68 68 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68 68 0 0 0 0
in 386.69 seconds
Image has 68 counts for 0.1759 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.evt
Total Good Bad: Region Time Phase Cut
68 48 0 0 0 20
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68 48 0 0 0 20
in 386.69 seconds
Image has 48 counts for 0.1241 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.evt
Total Good Bad: Region Time Phase Cut
68 20 0 0 0 48
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68 20 0 0 0 48
in 386.69 seconds
Image has 20 counts for 5.1722E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s000302h:ASCA >
!ad75071000s000302h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s000302h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s000302h:ASCA > read events ad75071000s000302h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s000302h:ASCA-SIS0-BRIGHT > set image sky
!ad75071000s000302h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad75071000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000302h.img
Wrote image to file ad75071000s000302h.img
!ad75071000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad75071000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000302h_lo.img
Wrote image to file ad75071000s000302h_lo.img
!ad75071000s000302h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad75071000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000302h_hi.img
Wrote image to file ad75071000s000302h_hi.img
!ad75071000s000302h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s000502m.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s000502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4902
Mean RA/DEC/ROLL : 13.0168 -29.0963 289.4902
Pnt RA/DEC/ROLL : 13.0534 -29.0675 289.4902
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 138
GTI intervals : 6
Total GTI (secs) : 528.524
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 86.09 86.09
20 Percent Complete: Total/live time: 150.09 150.09
30 Percent Complete: Total/live time: 441.76 441.76
40 Percent Complete: Total/live time: 441.76 441.76
50 Percent Complete: Total/live time: 448.89 448.89
60 Percent Complete: Total/live time: 448.89 448.89
70 Percent Complete: Total/live time: 528.52 528.52
100 Percent Complete: Total/live time: 528.52 528.52
Number of attitude steps used: 7
Number of attitude steps avail: 9195
Mean RA/DEC pixel offset: -25.4415 -78.8756
writing expo file: ad75071000s000502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s000502m.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s000502m
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.53E+03 72 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.evt
Total Good Bad: Region Time Phase Cut
72 72 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72 72 0 0 0 0
in 528.52 seconds
Image has 72 counts for 0.1362 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.evt
Total Good Bad: Region Time Phase Cut
72 56 0 0 0 16
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72 56 0 0 0 16
in 528.52 seconds
Image has 56 counts for 0.1060 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.evt
Total Good Bad: Region Time Phase Cut
72 16 0 0 0 56
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72 16 0 0 0 56
in 528.52 seconds
Image has 16 counts for 3.0273E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s000502m:ASCA >
!ad75071000s000502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s000502m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s000502m:ASCA > read events ad75071000s000502m.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s000502m:ASCA-SIS0-BRIGHT > set image sky
!ad75071000s000502m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad75071000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000502m.img
Wrote image to file ad75071000s000502m.img
!ad75071000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad75071000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000502m_lo.img
Wrote image to file ad75071000s000502m_lo.img
!ad75071000s000502m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad75071000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000502m_hi.img
Wrote image to file ad75071000s000502m_hi.img
!ad75071000s000502m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s000702h.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s000702h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4892
Mean RA/DEC/ROLL : 13.0152 -29.0955 289.4892
Pnt RA/DEC/ROLL : 13.0570 -29.0681 289.4892
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 0
GTI intervals : 1
Total GTI (secs) : 14.278
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 14.28 14.28
100 Percent Complete: Total/live time: 14.28 14.28
Number of attitude steps used: 2
Number of attitude steps avail: 103
Mean RA/DEC pixel offset: -11.3353 -48.4744
writing expo file: ad75071000s000702h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s000702h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s000702h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.14E+02 404 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 404 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
404 404 0 0 0 0
in 14.28 seconds
Image has 404 counts for 28.30 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 403 0 0 0 1
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
404 403 0 0 0 1
in 14.28 seconds
Image has 403 counts for 28.23 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 1 0 0 0 403
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
404 1 0 0 0 403
in 14.28 seconds
Image has 1 counts for 7.0040E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s000702h:ASCA >
!ad75071000s000702h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s000702h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s000702h:ASCA > read events ad75071000s000702h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s000702h:ASCA-SIS0-BRIGHT > set image sky
!ad75071000s000702h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad75071000s000702h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000702h.img
Wrote image to file ad75071000s000702h.img
!ad75071000s000702h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad75071000s000702h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000702h_lo.img
Wrote image to file ad75071000s000702h_lo.img
!ad75071000s000702h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad75071000s000702h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s000702h:ASCA-SIS0-BRIGHT > extract image
!ad75071000s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad75071000s000702h_hi.img
Wrote image to file ad75071000s000702h_hi.img
!ad75071000s000702h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4793
Mean RA/DEC/ROLL : 13.0357 -29.0881 289.4793
Pnt RA/DEC/ROLL : 12.8883 -29.3560 289.4793
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 323
GTI intervals : 43
Total GTI (secs) : 29330.701
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 5308.00 5308.00
20 Percent Complete: Total/live time: 6236.00 6236.00
30 Percent Complete: Total/live time: 9724.00 9724.00
40 Percent Complete: Total/live time: 12581.47 12581.47
50 Percent Complete: Total/live time: 15286.19 15286.19
60 Percent Complete: Total/live time: 17940.41 17940.41
70 Percent Complete: Total/live time: 21182.13 21182.13
80 Percent Complete: Total/live time: 24757.50 24757.50
90 Percent Complete: Total/live time: 27451.79 27451.79
100 Percent Complete: Total/live time: 29330.70 29330.70
Number of attitude steps used: 52
Number of attitude steps avail: 84359
Mean RA/DEC pixel offset: -33.0333 -22.9764
writing expo file: ad75071000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s100102h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s100102h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.29E+05 2477 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100102h.evt
Total Good Bad: Region Time Phase Cut
2477 2477 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2477 2477 0 0 0 0
in 29330.70 seconds
Image has 2477 counts for 8.4451E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100102h.evt
Total Good Bad: Region Time Phase Cut
2477 979 0 0 0 1498
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2477 979 0 0 0 1498
in 29330.70 seconds
Image has 979 counts for 3.3378E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100102h.evt
Total Good Bad: Region Time Phase Cut
2477 1498 0 0 0 979
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2477 1498 0 0 0 979
in 29330.70 seconds
Image has 1498 counts for 5.1073E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s100102h:ASCA >
!ad75071000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s100102h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s100102h:ASCA > read events ad75071000s100102h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad75071000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad75071000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100102h.img
Wrote image to file ad75071000s100102h.img
!ad75071000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad75071000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100102h_lo.img
Wrote image to file ad75071000s100102h_lo.img
!ad75071000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad75071000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100102h_hi.img
Wrote image to file ad75071000s100102h_hi.img
!ad75071000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4811
Mean RA/DEC/ROLL : 13.0349 -29.0897 289.4811
Pnt RA/DEC/ROLL : 12.8904 -29.3668 289.4811
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 295
GTI intervals : 40
Total GTI (secs) : 16288.083
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2009.97 2009.97
20 Percent Complete: Total/live time: 3833.97 3833.97
30 Percent Complete: Total/live time: 5539.01 5539.01
40 Percent Complete: Total/live time: 7065.09 7065.09
50 Percent Complete: Total/live time: 8516.95 8516.95
60 Percent Complete: Total/live time: 12264.60 12264.60
70 Percent Complete: Total/live time: 12264.60 12264.60
80 Percent Complete: Total/live time: 13280.08 13280.08
90 Percent Complete: Total/live time: 15348.48 15348.48
100 Percent Complete: Total/live time: 16288.08 16288.08
Number of attitude steps used: 50
Number of attitude steps avail: 34707
Mean RA/DEC pixel offset: -84.2679 -30.2780
writing expo file: ad75071000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s100202m.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s100202m
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1403 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100202m.evt
Total Good Bad: Region Time Phase Cut
1403 1403 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1403 1403 0 0 0 0
in 16288.08 seconds
Image has 1403 counts for 8.6137E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100202m.evt
Total Good Bad: Region Time Phase Cut
1403 592 0 0 0 811
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1403 592 0 0 0 811
in 16288.08 seconds
Image has 592 counts for 3.6346E-02 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100202m.evt
Total Good Bad: Region Time Phase Cut
1403 812 0 0 0 591
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1403 812 0 0 0 591
in 16288.08 seconds
Image has 812 counts for 4.9852E-02 counts/sec
Command not found; type ? for a command listing
!ad75071000s100202m:ASCA >
!ad75071000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s100202m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s100202m:ASCA > read events ad75071000s100202m.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad75071000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad75071000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100202m.img
Wrote image to file ad75071000s100202m.img
!ad75071000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad75071000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100202m_lo.img
Wrote image to file ad75071000s100202m_lo.img
!ad75071000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad75071000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100202m_hi.img
Wrote image to file ad75071000s100202m_hi.img
!ad75071000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad75071000s100402h.expo
ASCAEXPO_V0.9b
reading data file: ad75071000s100402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970629_1345.0030
making an exposure map...
Aspect RA/DEC/ROLL : 13.0364 -29.0835 289.4836
Mean RA/DEC/ROLL : 13.0328 -29.0913 289.4836
Pnt RA/DEC/ROLL : 13.0381 -29.0708 289.4836
Image rebin factor : 4
Attitude Records : 104808
Hot Pixels : 0
GTI intervals : 1
Total GTI (secs) : 14.278
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 14.28 14.28
100 Percent Complete: Total/live time: 14.28 14.28
Number of attitude steps used: 2
Number of attitude steps avail: 103
Mean RA/DEC pixel offset: -13.5574 -12.5488
writing expo file: ad75071000s100402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad75071000s100402h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] ad75071000s100402h
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 02:13:49 0.14E+02 401 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100402h.evt
Total Good Bad: Region Time Phase Cut
401 401 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
401 401 0 0 0 0
in 14.28 seconds
Image has 401 counts for 28.09 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100402h.evt
Total Good Bad: Region Time Phase Cut
401 392 0 0 0 9
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
401 392 0 0 0 9
in 14.28 seconds
Image has 392 counts for 27.46 counts/sec
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100402h.evt
Total Good Bad: Region Time Phase Cut
401 9 0 0 0 392
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
401 9 0 0 0 392
in 14.28 seconds
Image has 9 counts for 0.6304 counts/sec
Command not found; type ? for a command listing
!ad75071000s100402h:ASCA >
!ad75071000s100402h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!ad75071000s100402h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!ad75071000s100402h:ASCA > read events ad75071000s100402h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!ad75071000s100402h:ASCA-SIS1-BRIGHT > set image sky
!ad75071000s100402h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad75071000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100402h.img
Wrote image to file ad75071000s100402h.img
!ad75071000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad75071000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100402h_lo.img
Wrote image to file ad75071000s100402h_lo.img
!ad75071000s100402h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad75071000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad75071000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad75071000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad75071000s100402h_hi.img
Wrote image to file ad75071000s100402h_hi.img
!ad75071000s100402h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad75071000s000102h.expo ad75071000s000202m.expo ad75071000s000302h.expo ad75071000s000502m.expo ad75071000s000702h.expo ad75071000s100102h.expo ad75071000s100202m.expo ad75071000s100402h.expo-> Summing the following images to produce ad75071000sis32002_all.totsky
ad75071000s000102h.img ad75071000s000202m.img ad75071000s000302h.img ad75071000s000502m.img ad75071000s000702h.img ad75071000s100102h.img ad75071000s100202m.img ad75071000s100402h.img-> Summing the following images to produce ad75071000sis32002_lo.totsky
ad75071000s000102h_lo.img ad75071000s000202m_lo.img ad75071000s000302h_lo.img ad75071000s000502m_lo.img ad75071000s000702h_lo.img ad75071000s100102h_lo.img ad75071000s100202m_lo.img ad75071000s100402h_lo.img-> Summing the following images to produce ad75071000sis32002_hi.totsky
ad75071000s000102h_hi.img ad75071000s000202m_hi.img ad75071000s000302h_hi.img ad75071000s000502m_hi.img ad75071000s000702h_hi.img ad75071000s100102h_hi.img ad75071000s100202m_hi.img ad75071000s100402h_hi.img-> Running XIMAGE to create ad75071000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad75071000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad75071000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 1460.10 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1460 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 15.0000 15 0 ![9]XIMAGE> exit-> Summing gis images
ad75071000g200170h.expo ad75071000g200270m.expo ad75071000g200370l.expo ad75071000g300170h.expo ad75071000g300270m.expo ad75071000g300370l.expo-> Summing the following images to produce ad75071000gis25670_all.totsky
ad75071000g200170h.img ad75071000g200270m.img ad75071000g200370l.img ad75071000g300170h.img ad75071000g300270m.img ad75071000g300370l.img-> Summing the following images to produce ad75071000gis25670_lo.totsky
ad75071000g200170h_lo.img ad75071000g200270m_lo.img ad75071000g200370l_lo.img ad75071000g300170h_lo.img ad75071000g300270m_lo.img ad75071000g300370l_lo.img-> Summing the following images to produce ad75071000gis25670_hi.totsky
ad75071000g200170h_hi.img ad75071000g200270m_hi.img ad75071000g200370l_hi.img ad75071000g300170h_hi.img ad75071000g300270m_hi.img ad75071000g300370l_hi.img-> Running XIMAGE to create ad75071000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad75071000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 8.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 8 min: 0 ![2]XIMAGE> read/exp_map ad75071000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1676.42 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1676 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 7.00000 70 -1 i,inten,mm,pp 3 11.0000 11 0 i,inten,mm,pp 4 44.0000 44 0 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad75071000gis25670.src
187 68 7.03049e-06 250 18 4.31187-> Determining extraction radii
187 68 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad75071000sis32002.src
The sum of the selected column is 32971.000 The mean of the selected column is 314.00952 The standard deviation of the selected column is 17.201574 The minimum of selected column is 283.00000 The maximum of selected column is 350.00000 The number of points used in calculation is 105-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 39233.000 The mean of the selected column is 373.64762 The standard deviation of the selected column is 18.172772 The minimum of selected column is 332.00000 The maximum of selected column is 406.00000 The number of points used in calculation is 105-> Converting (748.0,272.0,2.0) to s1 detector coordinates
1 ad75071000s000102h.evt 3794 1 ad75071000s000202m.evt 3794 1 ad75071000s000702h.evt 3794 2 ad75071000s000302h.evt 140 2 ad75071000s000502m.evt 140-> Fetching SIS0_NOTCHIP0.1
ad75071000s000102h.evt ad75071000s000202m.evt ad75071000s000702h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
2 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
2 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
3 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.14E+02 404 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 493 1721 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 295 881 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 158 246 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3794 946 2848 0 0 0
in 44608.92 seconds
Spectrum has 946 counts for 2.1207E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 44609. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.95508E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 16 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000s010102_1.pi
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 493 1721 0 0 0
Writing events file
493 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 295 881 0 0 0
Writing events file
788 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 158 246 0 0 0
Writing events file
946 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3794 946 2848 0 0 0
in 44608.92 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000102h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad75071000s010102_1.pi group=yes
Wrote spectrum to ad75071000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad75071000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 44609. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.95508E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 20 are grouped by a factor 4 ... 21 - 22 are grouped by a factor 2 ... 23 - 25 are grouped by a factor 3 ... 26 - 29 are grouped by a factor 4 ... 30 - 34 are grouped by a factor 5 ... 35 - 38 are grouped by a factor 4 ... 39 - 43 are grouped by a factor 5 ... 44 - 57 are grouped by a factor 7 ... 58 - 63 are grouped by a factor 6 ... 64 - 74 are grouped by a factor 11 ... 75 - 87 are grouped by a factor 13 ... 88 - 111 are grouped by a factor 24 ... 112 - 137 are grouped by a factor 26 ... 138 - 171 are grouped by a factor 34 ... 172 - 220 are grouped by a factor 49 ... 221 - 318 are grouped by a factor 98 ... 319 - 473 are grouped by a factor 155 ... 474 - 504 are grouped by a factor 31 ... 505 - 511 are grouped by a factor 7 ... --------------------------------------------- ... ...... exiting, changes written to file : ad75071000s010102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad75071000s010102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 31 by 38 bins
expanded to 31 by 38 bins
First WMAP bin is at detector pixel 216 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 2.8484 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.23000E+02
Weighted mean angle from optical axis = 10.123 arcmin
-> Standard Output From STOOL group_event_files:1 ad75071000s000112h.evt 2488 2 ad75071000s000312h.evt 75-> SIS0_NOTCHIP0.1 already present in current directory
ad75071000s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 14:41:49 0.29E+05 2488 0110
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000112h.evt
Total Good Bad: Region Time Phase Cut
2488 535 1953 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2488 535 1953 0 0 0
in 29033.72 seconds
Spectrum has 535 counts for 1.8427E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 29034. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.95508E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000s010212_1.pi
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000112h.evt
Total Good Bad: Region Time Phase Cut
2488 535 1953 0 0 0
Writing events file
535 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2488 535 1953 0 0 0
in 29033.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000112h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad75071000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad75071000s010212_1.pi group=yes
Wrote spectrum to ad75071000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad75071000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 29034. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.95508E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 53 are grouped by a factor 22 ... 54 - 66 are grouped by a factor 13 ... 67 - 80 are grouped by a factor 14 ... 81 - 100 are grouped by a factor 20 ... 101 - 121 are grouped by a factor 21 ... 122 - 152 are grouped by a factor 31 ... 153 - 209 are grouped by a factor 57 ... 210 - 293 are grouped by a factor 84 ... 294 - 401 are grouped by a factor 108 ... 402 - 647 are grouped by a factor 246 ... 648 - 974 are grouped by a factor 327 ... 975 - 1019 are grouped by a factor 45 ... 1020 - 1023 are grouped by a factor 4 ... --------------------------------------------- ... ...... exiting, changes written to file : ad75071000s010212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad75071000s010212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 31 by 38 bins
expanded to 31 by 38 bins
First WMAP bin is at detector pixel 216 224
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 2.8484 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.23000E+02
Weighted mean angle from optical axis = 10.139 arcmin
-> Standard Output From STOOL group_event_files:1 ad75071000s100102h.evt 4281 1 ad75071000s100202m.evt 4281 1 ad75071000s100402h.evt 4281-> Fetching SIS1_NOTCHIP0.1
1 ad75071000s100112h.evt 2792-> SIS1_NOTCHIP0.1 already present in current directory
1 ad75071000g200170h.evt 12738 1 ad75071000g200270m.evt 12738 1 ad75071000g200370l.evt 12738-> GIS2_REGION256.4 already present in current directory
ad75071000g200170h.evt ad75071000g200270m.evt ad75071000g200370l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 363 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 7848 0 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 4527 0 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 363 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12738 12738 0 0 0 0
in 50299.63 seconds
Spectrum has 12738 counts for 0.2532 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 50300. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36888 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... 0 - 1023 are grouped by a factor 4
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad75071000g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad75071000g210170_0.pi group=yes
Wrote spectrum to ad75071000g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad75071000g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad75071000g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 50300. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 20 are grouped by a factor 21 ... 21 - 27 are single channels ... 28 - 39 are grouped by a factor 2 ... 40 - 42 are grouped by a factor 3 ... 43 - 50 are grouped by a factor 2 ... 51 - 53 are grouped by a factor 3 ... 54 - 55 are grouped by a factor 2 ... 56 - 58 are grouped by a factor 3 ... 59 - 78 are grouped by a factor 2 ... 79 - 79 are single channels ... 80 - 85 are grouped by a factor 2 ... 86 - 86 are single channels ... 87 - 88 are grouped by a factor 2 ... 89 - 90 are single channels ... 91 - 94 are grouped by a factor 2 ... 95 - 96 are single channels ... 97 - 98 are grouped by a factor 2 ... 99 - 103 are single channels ... 104 - 105 are grouped by a factor 2 ... 106 - 109 are single channels ... 110 - 113 are grouped by a factor 2 ... 114 - 122 are single channels ... 123 - 124 are grouped by a factor 2 ... 125 - 126 are single channels ... 127 - 130 are grouped by a factor 2 ... 131 - 135 are single channels ... 136 - 139 are grouped by a factor 2 ... 140 - 141 are single channels ... 142 - 143 are grouped by a factor 2 ... 144 - 144 are single channels ... 145 - 152 are grouped by a factor 2 ... 153 - 156 are single channels ... 157 - 160 are grouped by a factor 2 ... 161 - 162 are single channels ... 163 - 192 are grouped by a factor 2 ... 193 - 207 are grouped by a factor 3 ... 208 - 209 are grouped by a factor 2 ... 210 - 212 are grouped by a factor 3 ... 213 - 218 are grouped by a factor 2 ... 219 - 242 are grouped by a factor 3 ... 243 - 244 are grouped by a factor 2 ... 245 - 277 are grouped by a factor 3 ... 278 - 281 are grouped by a factor 4 ... 282 - 290 are grouped by a factor 3 ... 291 - 295 are grouped by a factor 5 ... 296 - 299 are grouped by a factor 4 ... 300 - 301 are grouped by a factor 2 ... 302 - 313 are grouped by a factor 3 ... 314 - 321 are grouped by a factor 4 ... 322 - 324 are grouped by a factor 3 ... 325 - 344 are grouped by a factor 4 ... 345 - 347 are grouped by a factor 3 ... 348 - 351 are grouped by a factor 4 ... 352 - 356 are grouped by a factor 5 ... 357 - 376 are grouped by a factor 4 ... 377 - 381 are grouped by a factor 5 ... 382 - 389 are grouped by a factor 4 ... 390 - 394 are grouped by a factor 5 ... 395 - 398 are grouped by a factor 4 ... 399 - 401 are grouped by a factor 3 ... 402 - 405 are grouped by a factor 4 ... 406 - 410 are grouped by a factor 5 ... 411 - 430 are grouped by a factor 4 ... 431 - 433 are grouped by a factor 3 ... 434 - 437 are grouped by a factor 4 ... 438 - 442 are grouped by a factor 5 ... 443 - 448 are grouped by a factor 6 ... 449 - 458 are grouped by a factor 5 ... 459 - 464 are grouped by a factor 6 ... 465 - 468 are grouped by a factor 4 ... 469 - 474 are grouped by a factor 6 ... 475 - 494 are grouped by a factor 5 ... 495 - 501 are grouped by a factor 7 ... 502 - 507 are grouped by a factor 6 ... 508 - 512 are grouped by a factor 5 ... 513 - 524 are grouped by a factor 6 ... 525 - 531 are grouped by a factor 7 ... 532 - 537 are grouped by a factor 6 ... 538 - 544 are grouped by a factor 7 ... 545 - 552 are grouped by a factor 8 ... 553 - 558 are grouped by a factor 6 ... 559 - 567 are grouped by a factor 9 ... 568 - 588 are grouped by a factor 7 ... 589 - 596 are grouped by a factor 8 ... 597 - 603 are grouped by a factor 7 ... 604 - 611 are grouped by a factor 8 ... 612 - 618 are grouped by a factor 7 ... 619 - 627 are grouped by a factor 9 ... 628 - 643 are grouped by a factor 8 ... 644 - 653 are grouped by a factor 10 ... 654 - 662 are grouped by a factor 9 ... 663 - 683 are grouped by a factor 7 ... 684 - 699 are grouped by a factor 8 ... 700 - 713 are grouped by a factor 7 ... 714 - 721 are grouped by a factor 8 ... 722 - 730 are grouped by a factor 9 ... 731 - 740 are grouped by a factor 10 ... 741 - 758 are grouped by a factor 9 ... 759 - 771 are grouped by a factor 13 ... 772 - 781 are grouped by a factor 10 ... 782 - 805 are grouped by a factor 12 ... 806 - 815 are grouped by a factor 10 ... 816 - 827 are grouped by a factor 12 ... 828 - 838 are grouped by a factor 11 ... 839 - 847 are grouped by a factor 9 ... 848 - 860 are grouped by a factor 13 ... 861 - 872 are grouped by a factor 12 ... 873 - 888 are grouped by a factor 16 ... 889 - 903 are grouped by a factor 15 ... 904 - 927 are grouped by a factor 12 ... 928 - 936 are grouped by a factor 9 ... 937 - 946 are grouped by a factor 10 ... 947 - 957 are grouped by a factor 11 ... 958 - 970 are grouped by a factor 13 ... 971 - 981 are grouped by a factor 11 ... 982 - 996 are grouped by a factor 15 ... 997 - 1018 are grouped by a factor 22 ... 1019 - 1023 are grouped by a factor 5 ... --------------------------------------------- ... ...... exiting, changes written to file : ad75071000g210170_0.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 1 1
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.27380E+04
Weighted mean angle from optical axis = 14.482 arcmin
-> Standard Output From STOOL group_event_files:1 ad75071000g300170h.evt 13565 1 ad75071000g300270m.evt 13565 1 ad75071000g300370l.evt 13565-> GIS3_REGION256.4 already present in current directory
ad75071000g300170h.evt ad75071000g300270m.evt ad75071000g300370l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 347 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 8431 0 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 4787 0 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 347 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13565 13565 0 0 0 0
in 50285.63 seconds
Spectrum has 13565 counts for 0.2698 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 50286. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36783 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... 0 - 1023 are grouped by a factor 4
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad75071000g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad75071000g310170_0.pi group=yes
Wrote spectrum to ad75071000g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad75071000g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad75071000g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 50286. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 20 are grouped by a factor 21 ... 21 - 30 are single channels ... 31 - 44 are grouped by a factor 2 ... 45 - 47 are grouped by a factor 3 ... 48 - 75 are grouped by a factor 2 ... 76 - 76 are single channels ... 77 - 80 are grouped by a factor 2 ... 81 - 81 are single channels ... 82 - 83 are grouped by a factor 2 ... 84 - 88 are single channels ... 89 - 90 are grouped by a factor 2 ... 91 - 92 are single channels ... 93 - 94 are grouped by a factor 2 ... 95 - 98 are single channels ... 99 - 102 are grouped by a factor 2 ... 103 - 107 are single channels ... 108 - 113 are grouped by a factor 2 ... 114 - 125 are single channels ... 126 - 127 are grouped by a factor 2 ... 128 - 128 are single channels ... 129 - 132 are grouped by a factor 2 ... 133 - 136 are single channels ... 137 - 140 are grouped by a factor 2 ... 141 - 141 are single channels ... 142 - 143 are grouped by a factor 2 ... 144 - 145 are single channels ... 146 - 149 are grouped by a factor 2 ... 150 - 150 are single channels ... 151 - 156 are grouped by a factor 2 ... 157 - 157 are single channels ... 158 - 159 are grouped by a factor 2 ... 160 - 162 are single channels ... 163 - 168 are grouped by a factor 2 ... 169 - 169 are single channels ... 170 - 175 are grouped by a factor 2 ... 176 - 176 are single channels ... 177 - 196 are grouped by a factor 2 ... 197 - 199 are grouped by a factor 3 ... 200 - 203 are grouped by a factor 2 ... 204 - 206 are grouped by a factor 3 ... 207 - 208 are grouped by a factor 2 ... 209 - 214 are grouped by a factor 3 ... 215 - 220 are grouped by a factor 2 ... 221 - 229 are grouped by a factor 3 ... 230 - 231 are grouped by a factor 2 ... 232 - 234 are grouped by a factor 3 ... 235 - 238 are grouped by a factor 2 ... 239 - 241 are grouped by a factor 3 ... 242 - 243 are grouped by a factor 2 ... 244 - 246 are grouped by a factor 3 ... 247 - 248 are grouped by a factor 2 ... 249 - 251 are grouped by a factor 3 ... 252 - 253 are grouped by a factor 2 ... 254 - 262 are grouped by a factor 3 ... 263 - 264 are grouped by a factor 2 ... 265 - 279 are grouped by a factor 3 ... 280 - 281 are grouped by a factor 2 ... 282 - 299 are grouped by a factor 3 ... 300 - 301 are grouped by a factor 2 ... 302 - 304 are grouped by a factor 3 ... 305 - 306 are grouped by a factor 2 ... 307 - 310 are grouped by a factor 4 ... 311 - 328 are grouped by a factor 3 ... 329 - 332 are grouped by a factor 4 ... 333 - 335 are grouped by a factor 3 ... 336 - 347 are grouped by a factor 4 ... 348 - 352 are grouped by a factor 5 ... 353 - 355 are grouped by a factor 3 ... 356 - 367 are grouped by a factor 4 ... 368 - 370 are grouped by a factor 3 ... 371 - 386 are grouped by a factor 4 ... 387 - 398 are grouped by a factor 3 ... 399 - 402 are grouped by a factor 4 ... 403 - 405 are grouped by a factor 3 ... 406 - 417 are grouped by a factor 4 ... 418 - 420 are grouped by a factor 3 ... 421 - 432 are grouped by a factor 4 ... 433 - 437 are grouped by a factor 5 ... 438 - 441 are grouped by a factor 4 ... 442 - 447 are grouped by a factor 6 ... 448 - 459 are grouped by a factor 4 ... 460 - 465 are grouped by a factor 6 ... 466 - 469 are grouped by a factor 4 ... 470 - 484 are grouped by a factor 5 ... 485 - 490 are grouped by a factor 6 ... 491 - 497 are grouped by a factor 7 ... 498 - 512 are grouped by a factor 5 ... 513 - 518 are grouped by a factor 6 ... 519 - 523 are grouped by a factor 5 ... 524 - 535 are grouped by a factor 6 ... 536 - 540 are grouped by a factor 5 ... 541 - 548 are grouped by a factor 8 ... 549 - 553 are grouped by a factor 5 ... 554 - 560 are grouped by a factor 7 ... 561 - 572 are grouped by a factor 6 ... 573 - 579 are grouped by a factor 7 ... 580 - 587 are grouped by a factor 8 ... 588 - 601 are grouped by a factor 7 ... 602 - 617 are grouped by a factor 8 ... 618 - 637 are grouped by a factor 10 ... 638 - 644 are grouped by a factor 7 ... 645 - 649 are grouped by a factor 5 ... 650 - 663 are grouped by a factor 7 ... 664 - 671 are grouped by a factor 8 ... 672 - 678 are grouped by a factor 7 ... 679 - 683 are grouped by a factor 5 ... 684 - 689 are grouped by a factor 6 ... 690 - 694 are grouped by a factor 5 ... 695 - 700 are grouped by a factor 6 ... 701 - 714 are grouped by a factor 7 ... 715 - 722 are grouped by a factor 8 ... 723 - 729 are grouped by a factor 7 ... 730 - 738 are grouped by a factor 9 ... 739 - 750 are grouped by a factor 12 ... 751 - 760 are grouped by a factor 10 ... 761 - 769 are grouped by a factor 9 ... 770 - 775 are grouped by a factor 6 ... 776 - 785 are grouped by a factor 10 ... 786 - 797 are grouped by a factor 12 ... 798 - 810 are grouped by a factor 13 ... 811 - 822 are grouped by a factor 12 ... 823 - 831 are grouped by a factor 9 ... 832 - 842 are grouped by a factor 11 ... 843 - 868 are grouped by a factor 13 ... 869 - 882 are grouped by a factor 14 ... 883 - 893 are grouped by a factor 11 ... 894 - 905 are grouped by a factor 12 ... 906 - 915 are grouped by a factor 10 ... 916 - 924 are grouped by a factor 9 ... 925 - 934 are grouped by a factor 10 ... 935 - 946 are grouped by a factor 12 ... 947 - 957 are grouped by a factor 11 ... 958 - 971 are grouped by a factor 14 ... 972 - 987 are grouped by a factor 16 ... 988 - 1009 are grouped by a factor 22 ... 1010 - 1023 are grouped by a factor 14 ... --------------------------------------------- ... ...... exiting, changes written to file : ad75071000g310170_0.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 1 1
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.35650E+04
Weighted mean angle from optical axis = 14.409 arcmin
-> Plotting ad75071000g210170_0_pi.ps from ad75071000g210170_0.pi
XSPEC 9.01 16:01:12 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad75071000g210170_0.pi
Net count rate (cts/s) for file 1 0.2532 +/- 2.2438E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad75071000g310170_0_pi.ps from ad75071000g310170_0.pi
XSPEC 9.01 16:01:26 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad75071000g310170_0.pi
Net count rate (cts/s) for file 1 0.2698 +/- 2.3161E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad75071000s010102_1_pi.ps from ad75071000s010102_1.pi
XSPEC 9.01 16:01:40 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad75071000s010102_1.pi
Net count rate (cts/s) for file 1 2.1207E-02+/- 6.9457E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad75071000s010212_1_pi.ps from ad75071000s010212_1.pi
XSPEC 9.01 16:01:54 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad75071000s010212_1.pi
Net count rate (cts/s) for file 1 1.8427E-02+/- 8.1724E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
2 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.39E+03 68 0110
2 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
3 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.39E+03 68 0110
2 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
3 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
4 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.53E+03 72 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.39E+03 68 0110
2 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
3 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
4 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.53E+03 72 0110
5 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.14E+02 404 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 500 1714 0 0 0
Writing events file
500 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 296 880 0 0 0
Writing events file
796 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.evt
Total Good Bad: Region Time Phase Cut
68 25 43 0 0 0
Writing events file
821 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.evt
Total Good Bad: Region Time Phase Cut
72 19 53 0 0 0
Writing events file
840 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 162 242 0 0 0
Writing events file
1002 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3934 1002 2932 0 0 0
in 45524.13 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000102h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad75071000s000702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad75071000s000002_1.lc with binsize 2271.6631576523
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.46E+05 1002 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1002 1002 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1002 1002 0 0 0 0
in 45524.13 seconds
Fits light curve has 1002 counts for 2.2010E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events events.tmp
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > set binsize 2271.6631576523
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad75071000s000002_1.lc
Wrote FITS light curve to file ad75071000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad75071000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad75071000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ SGP2 Start Time (d) .... 10628 14:08:15.477
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10630 00:30:07.477
No. of Rows ....... 18 Bin Time (s) ...... 2272.
Right Ascension ... 1.3036E+01 Internal time sys.. Converted to TJD
Declination ....... -2.9084E+01 Experiment ........ ASCA SIS0
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 55 Newbins of 2271.66 (s)
Intv 1 Start10628 16:20:46
Ser.1 Avg 0.2238E-01 Chisq 479.1 Var 0.3596E-03 Newbs. 18
Min 0.1305E-01 Max 0.9923E-01expVar 0.1351E-04 Bins 18
Results from Statistical Analysis
Newbin Integration Time (s).. 2271.7
Interval Duration (s)........ 0.11358E+06
No. of Newbins .............. 18
Average (c/s) ............... 0.22379E-01 +/- 0.89E-03
Standard Deviation (c/s)..... 0.18964E-01
Minimum (c/s)................ 0.13046E-01
Maximum (c/s)................ 0.99231E-01
Variance ((c/s)**2).......... 0.35962E-03 +/- 0.12E-03
Expected Variance ((c/s)**2). 0.13510E-04 +/- 0.46E-05
Third Moment ((c/s)**3)...... 0.25000E-04
Average Deviation (c/s)...... 0.90612E-02
Skewness..................... 3.6658 +/- 0.58
Kurtosis..................... 11.999 +/- 1.2
RMS fractional variation..... 0.83133 +/- 0.15
Chi-Square................... 479.13 dof 17
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.24588E-17 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 55 Newbins of 2271.66 (s)
Intv 1 Start10628 16:20:46
Ser.1 Avg 0.2238E-01 Chisq 479.1 Var 0.3596E-03 Newbs. 18
Min 0.1305E-01 Max 0.9923E-01expVar 0.1351E-04 Bins 18
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad75071000s000002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=8.0000000000E+00 for ad75071000s100102h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 363 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 7848 0 0 0 0
Writing events file
7848 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 4527 0 0 0 0
Writing events file
12375 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 363 0 0 0 0
Writing events file
12738 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12738 12738 0 0 0 0
in 50299.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > filter region ad75071000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad75071000g200070_0.lc with binsize 197.439260701848
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.50E+05 12738 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/events.tmp
Total Good Bad: Region Time Phase Cut
12738 12738 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12738 12738 0 0 0 0
in 50299.63 seconds
Fits light curve has 12738 counts for 0.2532 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events events.tmp
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > set binsize 197.439260701848
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad75071000g200070_0.lc
Wrote FITS light curve to file ad75071000g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad75071000g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad75071000g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ SGP2 Start Time (d) .... 10628 14:06:39.477
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10630 00:30:23.477
No. of Rows ....... 254 Bin Time (s) ...... 197.4
Right Ascension ... 1.3036E+01 Internal time sys.. Converted to TJD
Declination ....... -2.9084E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 242.127 (s)
Intv 1 Start10628 14: 8:40
Ser.1 Avg 0.2545 Chisq 238.2 Var 0.1533E-02 Newbs. 213
Min 0.1671 Max 0.4356 expVar 0.1246E-02 Bins 254
Results from Statistical Analysis
Newbin Integration Time (s).. 242.13
Interval Duration (s)........ 0.12349E+06
No. of Newbins .............. 213
Average (c/s) ............... 0.25452 +/- 0.24E-02
Standard Deviation (c/s)..... 0.39157E-01
Minimum (c/s)................ 0.16714
Maximum (c/s)................ 0.43558
Variance ((c/s)**2).......... 0.15333E-02 +/- 0.15E-03
Expected Variance ((c/s)**2). 0.12458E-02 +/- 0.12E-03
Third Moment ((c/s)**3)...... 0.48988E-04
Average Deviation (c/s)...... 0.29354E-01
Skewness..................... 0.81593 +/- 0.17
Kurtosis..................... 2.0244 +/- 0.34
RMS fractional variation....< 0.40629E-01 (3 sigma)
Chi-Square................... 238.15 dof 212
Chi-Square Prob of constancy. 0.10503 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.16642 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 242.127 (s)
Intv 1 Start10628 14: 8:40
Ser.1 Avg 0.2545 Chisq 238.2 Var 0.1533E-02 Newbs. 213
Min 0.1671 Max 0.4356 expVar 0.1246E-02 Bins 254
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad75071000g200070_0.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad75071000g300170h.evt
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 347 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 8431 0 0 0 0
Writing events file
8431 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 4787 0 0 0 0
Writing events file
13218 events written to the output file
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 347 0 0 0 0
Writing events file
13565 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13565 13565 0 0 0 0
in 50285.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > filter region ad75071000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad75071000g300070_0.lc with binsize 185.350632227043
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.50E+05 13565 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/events.tmp
Total Good Bad: Region Time Phase Cut
13565 13565 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13565 13565 0 0 0 0
in 50285.63 seconds
Fits light curve has 13565 counts for 0.2698 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events events.tmp
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > set binsize 185.350632227043
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad75071000g300070_0.lc
Wrote FITS light curve to file ad75071000g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad75071000g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad75071000g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ SGP2 Start Time (d) .... 10628 14:06:39.477
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10630 00:30:23.477
No. of Rows ....... 279 Bin Time (s) ...... 185.4
Right Ascension ... 1.3036E+01 Internal time sys.. Converted to TJD
Declination ....... -2.9084E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 242.127 (s)
Intv 1 Start10628 14: 8:40
Ser.1 Avg 0.2700 Chisq 280.8 Var 0.1966E-02 Newbs. 224
Min 0.1718 Max 0.4316 expVar 0.1408E-02 Bins 279
Results from Statistical Analysis
Newbin Integration Time (s).. 242.13
Interval Duration (s)........ 0.12349E+06
No. of Newbins .............. 224
Average (c/s) ............... 0.27003 +/- 0.25E-02
Standard Deviation (c/s)..... 0.44343E-01
Minimum (c/s)................ 0.17176
Maximum (c/s)................ 0.43161
Variance ((c/s)**2).......... 0.19663E-02 +/- 0.19E-03
Expected Variance ((c/s)**2). 0.14081E-02 +/- 0.13E-03
Third Moment ((c/s)**3)...... 0.46521E-04
Average Deviation (c/s)...... 0.34421E-01
Skewness..................... 0.53354 +/- 0.16
Kurtosis..................... 0.90863 +/- 0.33
RMS fractional variation..... 0.87500E-01 +/- 0.15E-01
Chi-Square................... 280.83 dof 223
Chi-Square Prob of constancy. 0.51895E-02 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.31332E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 242.127 (s)
Intv 1 Start10628 14: 8:40
Ser.1 Avg 0.2700 Chisq 280.8 Var 0.1966E-02 Newbs. 224
Min 0.1718 Max 0.4316 expVar 0.1408E-02 Bins 279
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad75071000g300070_0.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad75071000g200170h.evt[2] ad75071000g200270m.evt[2] ad75071000g200370l.evt[2]-> Making L1 light curve of ft970629_1345_0030G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 59362 output records from 59409 good input G2_L1 records.-> Making L1 light curve of ft970629_1345_0030G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 43086 output records from 75398 good input G2_L1 records.-> Merging GTIs from the following files:
ad75071000g300170h.evt[2] ad75071000g300270m.evt[2] ad75071000g300370l.evt[2]-> Making L1 light curve of ft970629_1345_0030G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 55556 output records from 55602 good input G3_L1 records.-> Making L1 light curve of ft970629_1345_0030G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 41941 output records from 71115 good input G3_L1 records.
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 7848 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.evt
Total Good Bad: Region Time Phase Cut
7848 7848 0 0 0 0
Writing events file
7848 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7848 7848 0 0 0 0
in 30643.71 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > filter region ad75071000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad75071000g200170h_0.ulc use_events=yes
Wrote events list to file ad75071000g200170h_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000g200270m_0.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4527 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.evt
Total Good Bad: Region Time Phase Cut
4527 4527 0 0 0 0
Writing events file
4527 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4527 4527 0 0 0 0
in 18297.48 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200270m.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > filter region ad75071000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad75071000g200270m_0.ulc use_events=yes
Wrote events list to file ad75071000g200270m_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000g200370l_0.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 363 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.evt
Total Good Bad: Region Time Phase Cut
363 363 0 0 0 0
Writing events file
363 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
363 363 0 0 0 0
in 1358.43 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200370l.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > filter region ad75071000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad75071000g200370l_0.ulc use_events=yes
Wrote events list to file ad75071000g200370l_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000g300170h_0.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.31E+05 8431 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.evt
Total Good Bad: Region Time Phase Cut
8431 8431 0 0 0 0
Writing events file
8431 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8431 8431 0 0 0 0
in 30645.71 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300170h.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > filter region ad75071000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad75071000g300170h_0.ulc use_events=yes
Wrote events list to file ad75071000g300170h_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000g300270m_0.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.18E+05 4787 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.evt
Total Good Bad: Region Time Phase Cut
4787 4787 0 0 0 0
Writing events file
4787 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4787 4787 0 0 0 0
in 18281.48 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300270m.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > filter region ad75071000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad75071000g300270m_0.ulc use_events=yes
Wrote events list to file ad75071000g300270m_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000g300370l_0.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.14E+04 347 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.evt
Total Good Bad: Region Time Phase Cut
347 347 0 0 0 0
Writing events file
347 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
347 347 0 0 0 0
in 1358.43 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300370l.evt
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > filter region ad75071000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad75071000g300370l_0.ulc use_events=yes
Wrote events list to file ad75071000g300370l_0.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad75071000s000102h_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.29E+05 2214 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.evt
Total Good Bad: Region Time Phase Cut
2214 500 1714 0 0 0
Writing events file
500 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2214 500 1714 0 0 0
in 29033.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000102h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad75071000s000102h_1.ulc use_events=yes
Wrote events list to file ad75071000s000102h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad75071000s000112h_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 14:41:49 0.29E+05 2488 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000112h.evt
Total Good Bad: Region Time Phase Cut
2488 541 1947 0 0 0
Writing events file
541 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2488 541 1947 0 0 0
in 29033.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000112h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad75071000s000112h_1.ulc use_events=yes
Wrote events list to file ad75071000s000112h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad75071000s000202m_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.16E+05 1176 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.evt
Total Good Bad: Region Time Phase Cut
1176 296 880 0 0 0
Writing events file
296 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1176 296 880 0 0 0
in 15560.92 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000202m.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad75071000s000202m_1.ulc use_events=yes
Wrote events list to file ad75071000s000202m_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad75071000s000302h_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.39E+03 68 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.evt
Total Good Bad: Region Time Phase Cut
68 25 43 0 0 0
Writing events file
25 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68 25 43 0 0 0
in 386.69 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000302h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad75071000s000302h_1.ulc use_events=yes
Wrote events list to file ad75071000s000302h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad75071000s000312h_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 13:45:17 0.39E+03 75 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000312h.evt
Total Good Bad: Region Time Phase Cut
75 26 49 0 0 0
Writing events file
26 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
75 26 49 0 0 0
in 386.69 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000312h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad75071000s000312h_1.ulc use_events=yes
Wrote events list to file ad75071000s000312h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad75071000s000502m_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.53E+03 72 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.evt
Total Good Bad: Region Time Phase Cut
72 19 53 0 0 0
Writing events file
19 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72 19 53 0 0 0
in 528.52 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000502m.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad75071000s000502m_1.ulc use_events=yes
Wrote events list to file ad75071000s000502m_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad75071000s000702h_1.ulc
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.14E+02 404 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.evt
Total Good Bad: Region Time Phase Cut
404 162 242 0 0 0
Writing events file
162 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
404 162 242 0 0 0
in 14.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000s000702h.evt
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad75071000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad75071000s000702h_1.ulc use_events=yes
Wrote events list to file ad75071000s000702h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/75071000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad75071000s100102h_1.ulc since ad75071000s132002_1.reg does not exist*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 26224 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft970629_1345_0030.mkf
1 ad75071000g200170h.unf 66795 1 ad75071000g200270m.unf 66795 1 ad75071000g200370l.unf 66795-> Fetching GIS2_CALSRC256.2
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 21409 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 21409 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 12310 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.unf
Total Good Bad: Region Time Phase Cut
33076 6551 26525 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.unf
Total Good Bad: Region Time Phase Cut
21409 4551 16858 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.unf
Total Good Bad: Region Time Phase Cut
12310 2987 9323 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
66795 14089 52706 0 0 0
in 91379.51 seconds
Spectrum has 14089 counts for 0.1542 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 91380. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... 0 - 1023 are grouped by a factor 4
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g200170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > read events ad75071000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad75071000g220170.cal group=yes
Wrote spectrum to ad75071000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 16:36:28 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad75071000g220170.cal
Net count rate (cts/s) for file 1 0.1542 +/- 1.2992E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 3.9541E+06 using 84 PHA bins.
Reduced chi-squared = 5.1352E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 3.9296E+06 using 84 PHA bins.
Reduced chi-squared = 5.0379E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 3.9296E+06 using 84 PHA bins.
Reduced chi-squared = 4.9741E+04
!XSPEC> renorm
Chi-Squared = 3877. using 84 PHA bins.
Reduced chi-squared = 49.07
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2885.2 0 1.000 5.893 0.1287 4.5619E-02
4.0352E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1229.9 0 1.000 5.867 0.1764 6.7175E-02
3.5992E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
487.07 -1 1.000 5.930 0.1943 9.5329E-02
2.3142E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
426.31 -2 1.000 5.970 0.2112 0.1076
1.4847E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
415.14 -3 1.000 5.949 0.1937 0.1036
1.8722E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
413.52 -4 1.000 5.959 0.2003 0.1056
1.6757E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.76 -5 1.000 5.954 0.1966 0.1047
1.7661E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.70 -1 1.000 5.955 0.1975 0.1049
1.7395E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
412.70 0 1.000 5.955 0.1975 0.1049
1.7395E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95545 +/- 0.52045E-02
3 3 2 gaussian/b Sigma 0.197539 +/- 0.53294E-02
4 4 2 gaussian/b norm 0.104924 +/- 0.14350E-02
5 2 3 gaussian/b LineE 6.55698 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.207276 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.739456E-02 +/- 0.10343E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 412.7 using 84 PHA bins.
Reduced chi-squared = 5.224
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad75071000g220170.cal peaks at 5.95545 +/- 0.0052045 keV1 ad75071000g300170h.unf 61431 1 ad75071000g300270m.unf 61431 1 ad75071000g300370l.unf 61431-> Fetching GIS3_CALSRC256.2
** XSELECT V1.4b **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 19495 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
2 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 19495 1024
3 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 11366 1024
extractor v3.42 9 Oct 1998
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.unf
Total Good Bad: Region Time Phase Cut
30570 5863 24707 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.unf
Total Good Bad: Region Time Phase Cut
19495 3994 15501 0 0 0
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.unf
Total Good Bad: Region Time Phase Cut
11366 2637 8729 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
61431 12494 48937 0 0 0
in 91361.51 seconds
Spectrum has 12494 counts for 0.1368 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - NONE Instrument filter in use
EXPOSURE - 91362. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... 0 - 1023 are grouped by a factor 4
... ---------------------------------------------
...
...... exiting, changes written to file : ad75071000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!xsel:ASCA > read events ad75071000g300170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > read events ad75071000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad75071000g320170.cal group=yes
Wrote spectrum to ad75071000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 16:37:33 4-Mar-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad75071000g320170.cal
Net count rate (cts/s) for file 1 0.1368 +/- 1.2237E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 4.6656E+06 using 84 PHA bins.
Reduced chi-squared = 6.0593E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 4.6289E+06 using 84 PHA bins.
Reduced chi-squared = 5.9345E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 4.6289E+06 using 84 PHA bins.
Reduced chi-squared = 5.8594E+04
!XSPEC> renorm
Chi-Squared = 4254. using 84 PHA bins.
Reduced chi-squared = 53.85
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
3383.4 0 1.000 5.893 9.7177E-02 4.0506E-02
3.4554E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1259.9 0 1.000 5.864 0.1454 6.4911E-02
2.9752E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
377.82 -1 1.000 5.919 0.1592 9.3757E-02
1.8321E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
325.77 -2 1.000 5.941 0.1664 0.1021
1.3750E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
322.65 -3 1.000 5.934 0.1595 0.1011
1.4822E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
322.56 -4 1.000 5.936 0.1601 0.1013
1.4559E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
322.52 -5 1.000 5.935 0.1598 0.1013
1.4618E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
322.52 0 1.000 5.935 0.1598 0.1013
1.4615E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93543 +/- 0.41234E-02
3 3 2 gaussian/b Sigma 0.159758 +/- 0.50229E-02
4 4 2 gaussian/b norm 0.101286 +/- 0.12535E-02
5 2 3 gaussian/b LineE 6.53494 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.167632 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.461505E-02 +/- 0.76942E-03
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 322.5 using 84 PHA bins.
Reduced chi-squared = 4.083
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad75071000g320170.cal peaks at 5.93543 +/- 0.0041234 keV
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 14:41:49 0.41E+05 349504 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000102h.unf
Total Good Bad: Region Time Phase Cut
349504 36656 0 312848 0 0
Writing events file
36656 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349504 36656 0 312848 0 0
in 4462.69 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000102h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 36656
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 56 19808
Flickering pixels iter, pixels & cnts : 1 31 689
cleaning chip # 2
Hot pixels & counts : 39 15250
Flickering pixels iter, pixels & cnts : 1 19 266
cleaning chip # 3
Number of pixels rejected : 145
Number of (internal) image counts : 36656
Number of image cts rejected (N, %) : 3601398.25
By chip : 0 1 2 3
Pixels rejected : 0 87 58 0
Image counts : 0 20760 15896 0
Image cts rejected: 0 20497 15516 0
Image cts rej (%) : 0.00 98.73 97.61 0.00
filtering data...
Total counts : 0 20760 15896 0
Total cts rejected: 0 20497 15516 0
Total cts rej (%) : 0.00 98.73 97.61 0.00
Number of clean counts accepted : 643
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 145
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000112h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 14:41:49 0.41E+05 351164 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000112h.unf
Total Good Bad: Region Time Phase Cut
351164 36786 0 314378 0 0
Writing events file
36786 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
351164 36786 0 314378 0 0
in 4462.69 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000112h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad75071000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 36786
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 56 19809
Flickering pixels iter, pixels & cnts : 1 31 689
cleaning chip # 2
Hot pixels & counts : 39 15256
Flickering pixels iter, pixels & cnts : 1 19 267
cleaning chip # 3
Number of pixels rejected : 145
Number of (internal) image counts : 36786
Number of image cts rejected (N, %) : 3602197.92
By chip : 0 1 2 3
Pixels rejected : 0 87 58 0
Image counts : 0 20828 15958 0
Image cts rejected: 0 20498 15523 0
Image cts rej (%) : 0.00 98.42 97.27 0.00
filtering data...
Total counts : 0 20828 15958 0
Total cts rejected: 0 20498 15523 0
Total cts rej (%) : 0.00 98.42 97.27 0.00
Number of clean counts accepted : 765
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 145
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000202m.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.24E+05 207224 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000202m.unf
Total Good Bad: Region Time Phase Cut
207224 30911 0 176313 0 0
Writing events file
30911 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
207224 30911 0 176313 0 0
in 3792.25 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000202m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 30911
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 53 16453
Flickering pixels iter, pixels & cnts : 1 29 662
cleaning chip # 2
Hot pixels & counts : 37 12780
Flickering pixels iter, pixels & cnts : 1 23 316
cleaning chip # 3
Number of pixels rejected : 142
Number of (internal) image counts : 30911
Number of image cts rejected (N, %) : 3021197.74
By chip : 0 1 2 3
Pixels rejected : 0 82 60 0
Image counts : 0 17489 13422 0
Image cts rejected: 0 17115 13096 0
Image cts rej (%) : 0.00 97.86 97.57 0.00
filtering data...
Total counts : 0 17489 13422 0
Total cts rejected: 0 17115 13096 0
Total cts rej (%) : 0.00 97.86 97.57 0.00
Number of clean counts accepted : 700
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 142
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000302h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.45E+04 40900 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000302h.unf
Total Good Bad: Region Time Phase Cut
40900 6090 0 34810 0 0
Writing events file
6090 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
40900 6090 0 34810 0 0
in 811.28 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000302h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000302h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000302h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6090
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 48 3334
Flickering pixels iter, pixels & cnts : 1 24 222
cleaning chip # 2
Hot pixels & counts : 31 2288
Flickering pixels iter, pixels & cnts : 1 14 103
cleaning chip # 3
Number of pixels rejected : 117
Number of (internal) image counts : 6090
Number of image cts rejected (N, %) : 594797.65
By chip : 0 1 2 3
Pixels rejected : 0 72 45 0
Image counts : 0 3630 2460 0
Image cts rejected: 0 3556 2391 0
Image cts rej (%) : 0.00 97.96 97.20 0.00
filtering data...
Total counts : 0 3630 2460 0
Total cts rejected: 0 3556 2391 0
Total cts rej (%) : 0.00 97.96 97.20 0.00
Number of clean counts accepted : 143
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 117
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000312h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 13:45:17 0.45E+04 41470 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000312h.unf
Total Good Bad: Region Time Phase Cut
41470 6112 0 35358 0 0
Writing events file
6112 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
41470 6112 0 35358 0 0
in 811.28 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000312h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad75071000s000312h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000312h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6112
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 48 3337
Flickering pixels iter, pixels & cnts : 1 24 223
cleaning chip # 2
Hot pixels & counts : 31 2293
Flickering pixels iter, pixels & cnts : 1 14 103
cleaning chip # 3
Number of pixels rejected : 117
Number of (internal) image counts : 6112
Number of image cts rejected (N, %) : 595697.45
By chip : 0 1 2 3
Pixels rejected : 0 72 45 0
Image counts : 0 3641 2471 0
Image cts rejected: 0 3560 2396 0
Image cts rej (%) : 0.00 97.78 96.96 0.00
filtering data...
Total counts : 0 3641 2471 0
Total cts rejected: 0 3560 2396 0
Total cts rej (%) : 0.00 97.78 96.96 0.00
Number of clean counts accepted : 156
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 117
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000402l.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 14:24:41 0.12E+05 87731 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000402l.unf
Total Good Bad: Region Time Phase Cut
87731 71976 0 15755 0 0
Writing events file
71976 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
87731 71976 0 15755 0 0
in 9527.29 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000402l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000402l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000402l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 71976
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 54 36553
Flickering pixels iter, pixels & cnts : 1 33 1158
cleaning chip # 2
Hot pixels & counts : 40 32955
Flickering pixels iter, pixels & cnts : 1 23 488
cleaning chip # 3
Number of pixels rejected : 150
Number of (internal) image counts : 71976
Number of image cts rejected (N, %) : 7115498.86
By chip : 0 1 2 3
Pixels rejected : 0 87 63 0
Image counts : 0 38073 33903 0
Image cts rejected: 0 37711 33443 0
Image cts rej (%) : 0.00 99.05 98.64 0.00
filtering data...
Total counts : 0 38073 33903 0
Total cts rejected: 0 37711 33443 0
Total cts rej (%) : 0.00 99.05 98.64 0.00
Number of clean counts accepted : 822
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 150
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000502m.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 19:47:41 0.80E+04 34336 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000502m.unf
Total Good Bad: Region Time Phase Cut
34336 1704 0 32632 0 0
Writing events file
1704 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34336 1704 0 32632 0 0
in 241.06 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000502m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000502m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000502m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1704
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 34 779
Flickering pixels iter, pixels & cnts : 1 21 122
cleaning chip # 2
Hot pixels & counts : 29 646
Flickering pixels iter, pixels & cnts : 1 13 61
cleaning chip # 3
Number of pixels rejected : 97
Number of (internal) image counts : 1704
Number of image cts rejected (N, %) : 160894.37
By chip : 0 1 2 3
Pixels rejected : 0 55 42 0
Image counts : 0 951 753 0
Image cts rejected: 0 901 707 0
Image cts rej (%) : 0.00 94.74 93.89 0.00
filtering data...
Total counts : 0 951 753 0
Total cts rejected: 0 901 707 0
Total cts rej (%) : 0.00 94.74 93.89 0.00
Number of clean counts accepted : 96
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 97
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000602l.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 15:06:17 0.12E+05 17331 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s000602l.unf
Total Good Bad: Region Time Phase Cut
17331 12290 0 5041 0 0
Writing events file
12290 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17331 12290 0 5041 0 0
in 1813.35 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000602l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s000602l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s000602l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12290
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 47 6418
Flickering pixels iter, pixels & cnts : 1 29 348
cleaning chip # 2
Hot pixels & counts : 39 5044
Flickering pixels iter, pixels & cnts : 1 29 201
cleaning chip # 3
Number of pixels rejected : 144
Number of (internal) image counts : 12290
Number of image cts rejected (N, %) : 1201197.73
By chip : 0 1 2 3
Pixels rejected : 0 76 68 0
Image counts : 0 6889 5401 0
Image cts rejected: 0 6766 5245 0
Image cts rej (%) : 0.00 98.21 97.11 0.00
filtering data...
Total counts : 0 6889 5401 0
Total cts rejected: 0 6766 5245 0
Total cts rej (%) : 0.00 98.21 97.11 0.00
Number of clean counts accepted : 279
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 144
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s000702h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 12:59:13 0.48E+02 1767 0110
extractor v3.42 9 Oct 1998
No events selected from file: /data/data22/seq_proc/75071000.004/ad75071000s000702h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s000702h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad75071000s000702h.drk since it contains 0 events
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-29 13:45:17 0.46E+05 715420 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100102h.unf
Total Good Bad: Region Time Phase Cut
715420 82752 0 632668 0 0
Writing events file
82752 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
715420 82752 0 632668 0 0
in 5277.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s100102h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 82752
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 78 40317
Flickering pixels iter, pixels & cnts : 1 48 1556
cleaning chip # 2
Hot pixels & counts : 82 38383
Flickering pixels iter, pixels & cnts : 1 56 1605
cleaning chip # 3
Number of pixels rejected : 264
Number of (internal) image counts : 82752
Number of image cts rejected (N, %) : 8186198.92
By chip : 0 1 2 3
Pixels rejected : 0 126 138 0
Image counts : 0 42250 40502 0
Image cts rejected: 0 41873 39988 0
Image cts rej (%) : 0.00 99.11 98.73 0.00
filtering data...
Total counts : 0 42250 40502 0
Total cts rejected: 0 41873 39988 0
Total cts rej (%) : 0.00 99.11 98.73 0.00
Number of clean counts accepted : 891
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 264
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s100112h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT2 HIGH 1997-06-29 13:45:17 0.46E+05 718166 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100112h.unf
Total Good Bad: Region Time Phase Cut
718166 82937 0 635229 0 0
Writing events file
82937 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
718166 82937 0 635229 0 0
in 5277.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s100112h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad75071000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 82937
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 78 40356
Flickering pixels iter, pixels & cnts : 1 48 1556
cleaning chip # 2
Hot pixels & counts : 81 38282
Flickering pixels iter, pixels & cnts : 1 57 1723
cleaning chip # 3
Number of pixels rejected : 264
Number of (internal) image counts : 82937
Number of image cts rejected (N, %) : 8191798.77
By chip : 0 1 2 3
Pixels rejected : 0 126 138 0
Image counts : 0 42344 40593 0
Image cts rejected: 0 41912 40005 0
Image cts rej (%) : 0.00 98.98 98.55 0.00
filtering data...
Total counts : 0 42344 40593 0
Total cts rejected: 0 41912 40005 0
Total cts rej (%) : 0.00 98.98 98.55 0.00
Number of clean counts accepted : 1020
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 264
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s100202m.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT MEDIUM 1997-06-29 13:56:13 0.32E+05 459114 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100202m.unf
Total Good Bad: Region Time Phase Cut
459114 62559 0 396555 0 0
Writing events file
62559 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
459114 62559 0 396555 0 0
in 4033.31 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s100202m.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 62559
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 76 30439
Flickering pixels iter, pixels & cnts : 1 49 1256
cleaning chip # 2
Hot pixels & counts : 76 28473
Flickering pixels iter, pixels & cnts : 1 55 1570
cleaning chip # 3
Number of pixels rejected : 256
Number of (internal) image counts : 62559
Number of image cts rejected (N, %) : 6173898.69
By chip : 0 1 2 3
Pixels rejected : 0 125 131 0
Image counts : 0 32117 30442 0
Image cts rejected: 0 31695 30043 0
Image cts rej (%) : 0.00 98.69 98.69 0.00
filtering data...
Total counts : 0 32117 30442 0
Total cts rejected: 0 31695 30043 0
Total cts rej (%) : 0.00 98.69 98.69 0.00
Number of clean counts accepted : 821
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 256
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s100302l.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT LOW 1997-06-29 14:24:41 0.24E+05 123973 0110
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000s100302l.unf
Total Good Bad: Region Time Phase Cut
123973 90656 0 33317 0 0
Writing events file
90656 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
123973 90656 0 33317 0 0
in 11340.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s100302l.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad75071000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad75071000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 90656
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 40 43477
Flickering pixels iter, pixels & cnts : 1 30 1545
cleaning chip # 2
Hot pixels & counts : 45 43330
Flickering pixels iter, pixels & cnts : 1 48 1803
cleaning chip # 3
Number of pixels rejected : 163
Number of (internal) image counts : 90656
Number of image cts rejected (N, %) : 9015599.45
By chip : 0 1 2 3
Pixels rejected : 0 70 93 0
Image counts : 0 45312 45344 0
Image cts rejected: 0 45022 45133 0
Image cts rej (%) : 0.00 99.36 99.53 0.00
filtering data...
Total counts : 0 45312 45344 0
Total cts rejected: 0 45022 45133 0
Total cts rej (%) : 0.00 99.36 99.53 0.00
Number of clean counts accepted : 501
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 163
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad75071000s100402h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 SGP2 BRIGHT HIGH 1997-06-30 02:13:49 0.60E+02 1865 0110
extractor v3.42 9 Oct 1998
No events selected from file: /data/data22/seq_proc/75071000.004/ad75071000s100402h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000s100402h.unf
Setting...
Image keywords = DETX DETY with binning = 4
WMAP keywords = DETX DETY with binning = 8
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad75071000s100402h.drk since it contains 0 events
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.unf
Total Good Bad: Region Time Phase Cut
33076 3149 0 29927 0 0
Writing events file
3149 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
33076 3149 0 29927 0 0
in 5246.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad75071000g200170h.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 33076 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200170h.unf
Total Good Bad: Region Time Phase Cut
33076 765 0 32311 0 0
Writing events file
765 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
33076 765 0 32311 0 0
in 1372.21 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad75071000g200270m.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 21409 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.unf
Total Good Bad: Region Time Phase Cut
21409 2511 0 18898 0 0
Writing events file
2511 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21409 2511 0 18898 0 0
in 4071.69 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad75071000g200270m.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 21409 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200270m.unf
Total Good Bad: Region Time Phase Cut
21409 3191 0 18218 0 0
Writing events file
3191 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21409 3191 0 18218 0 0
in 5279.70 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad75071000g200370l.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 12310 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.unf
Total Good Bad: Region Time Phase Cut
12310 6853 0 5457 0 0
Writing events file
6853 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12310 6853 0 5457 0 0
in 11447.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad75071000g200370l.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 12310 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g200370l.unf
Total Good Bad: Region Time Phase Cut
12310 3891 0 8419 0 0
Writing events file
3891 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12310 3891 0 8419 0 0
in 5855.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g200370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad75071000g300170h.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.unf
Total Good Bad: Region Time Phase Cut
30570 2961 0 27609 0 0
Writing events file
2961 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30570 2961 0 27609 0 0
in 5244.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad75071000g300170h.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH HIGH 1997-06-29 13:45:27 0.42E+05 30570 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300170h.unf
Total Good Bad: Region Time Phase Cut
30570 713 0 29857 0 0
Writing events file
713 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30570 713 0 29857 0 0
in 1370.21 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300170h.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad75071000g300270m.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 19495 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.unf
Total Good Bad: Region Time Phase Cut
19495 2085 0 17410 0 0
Writing events file
2085 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19495 2085 0 17410 0 0
in 4071.69 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad75071000g300270m.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH MEDIUM 1997-06-29 13:56:55 0.30E+05 19495 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300270m.unf
Total Good Bad: Region Time Phase Cut
19495 2918 0 16577 0 0
Writing events file
2918 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19495 2918 0 16577 0 0
in 5279.70 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300270m.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad75071000g300370l.unf
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 11366 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.unf
Total Good Bad: Region Time Phase Cut
11366 6307 0 5059 0 0
Writing events file
6307 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11366 6307 0 5059 0 0
in 11447.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad75071000g300370l.brt
** XSELECT V1.4b **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 SGP2 PH LOW 1997-06-29 14:24:55 0.19E+05 11366 1024
extractor v3.42 9 Oct 1998
Doing file: /data/data22/seq_proc/75071000.004/ad75071000g300370l.unf
Total Good Bad: Region Time Phase Cut
11366 3603 0 7763 0 0
Writing events file
3603 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11366 3603 0 7763 0 0
in 5855.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Time keyword is TIME in units of s
Default timing binsize = 16.000
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/75071000.004/
Setting mkf directory to /data/data22/seq_proc/75071000.004/
!earthevents:ASCA > read events ad75071000g300370l.unf
Setting...
Image keywords = DETX DETY with binning = 1
WMAP keywords = DETX DETY with binning = 1
Energy keywords = PI with binning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/75071000.004/
HK Directory is: /data/data22/seq_proc/75071000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 184896004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-11-11 00:00:00.00000 Modified Julian Day = 51128.000000000000000-> leapsec.fits already present in current directory
Offset of 165542404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-04-01 00:00:00.00000 Modified Julian Day = 50904.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
ad75071000s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000302h.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad75071000s000702h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000102h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad75071000s000302h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad75071000s000702h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion-> listing ad75071000s000102h.unf
ad75071000s000202m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000502m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad75071000s000202m.unf
ad75071000s000402l.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000602l.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad75071000s000402l.unf
ad75071000s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000312h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad75071000s000112h.unf
ad75071000s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad75071000s000301h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad75071000s000101h.unf
ad75071000s100102h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad75071000s100402h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion-> listing ad75071000s100102h.unf
536 610 2331 610 4299 640 6213 624 8181 704 10093 624 12038 612 13943 612 15862 610 17753 114 20114 104 22406 100 24392 704 7
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files