The following information is also available:
Time column is TIME ORDERED-> Fetching fa940805_2305.0035.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 50281513.435700 50373357.660700
Data file start and stop ascatime : 50281513.435700 50373357.660700
Aspecting run start and stop ascatime : 50281513.435811 50373357.660636
Time interval averaged over (seconds) : 91844.224826
Total pointing and manuver time (sec) : 56516.984375 35327.488281
Mean boresight Euler angles : 13.866001 63.758491 35.805607
RA DEC SUN ANGLE
Mean solar position (deg) : 135.30 16.96
Mean aberration (arcsec) : 9.82 -2.84
Mean sat X-axis (deg) : 72.360301 -46.670775 85.04
Mean sat Y-axis (deg) : 121.556535 31.650885 19.26
Mean sat Z-axis (deg) : 13.866001 26.241510 108.57
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 14.007356 26.495993 305.742889 0.165747
Minimum 13.998418 26.492100 305.730225 0.000000
Maximum 14.026995 26.521322 305.765320 1.823804
Sigma (RMS) 0.000359 0.000353 0.003035 0.132050
Number of ASPECT records processed = 75975
Aspecting to RA/DEC : 14.00735569 26.49599266
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 14.007 DEC: 26.496
START TIME: SC 50281513.4358 = UT 05/08/94 23:05:13
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000089 1.434 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
1899.994507 1.783 C02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0
2259.993408 0.774 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
4095.987793 0.218 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
7643.977051 0.171 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
9851.970703 0.178 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
13387.959961 0.250 C02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0
15611.953125 0.202 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
19139.943359 0.298 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
21355.935547 0.128 1C2443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 4 3
24891.925781 0.201 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
27099.917969 0.103 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
30641.908203 0.083 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
32859.902344 0.151 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
36395.890625 0.123 E02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 4
38603.882812 0.193 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
42155.875000 0.158 E02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 4
44363.867188 0.219 1C2443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 4 3
47899.855469 0.185 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
50107.851562 0.185 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
53659.839844 0.152 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
55867.832031 0.177 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
59403.820312 0.125 E02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 4
61611.816406 0.123 1C2443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 4 3
65163.804688 0.135 C02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0
67371.796875 0.103 182443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 0 3
70907.789062 0.092 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
73109.781250 0.086 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
76667.773438 0.105 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
78861.765625 0.138 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
82411.750000 0.154 C02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0
84613.750000 0.126 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
88157.734375 0.189 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
90365.726562 0.105 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
91844.226562 0.523 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
Attitude Records: 75975
Attitude Steps: 35
Maneuver ACM time: 35327.5 sec
Pointed ACM time: 56517.0 sec
-> Calculating aspect point97 101 count=20344 sum1=282030 sum2=1.29713e+06 sum3=728431 97 102 count=3785 sum1=52465.3 sum2=241339 sum3=135519 98 100 count=28 sum1=388.35 sum2=1784.93 sum3=1002.52 98 101 count=51400 sum1=712767 sum2=3.27718e+06 sum3=1.84042e+06 98 102 count=15 sum1=207.975 sum2=956.43 sum3=536.997 99 99 count=181 sum1=2512.92 sum2=11536 sum3=6479.91 99 100 count=4 sum1=55.501 sum2=254.969 sum3=143.209 100 99 count=215 sum1=2985.28 sum2=13703 sum3=7697.45 100 100 count=2 sum1=27.77 sum2=127.484 sum3=71.65 0 out of 75974 points outside bin structure-> Euler angles: 13.8657, 63.7589, 35.8057
Interpolating 1 records in time interval 5.03734e+07 - 5.03734e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft940805_2305.0035",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft940805_2305.0035 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 1216256 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 1215232 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 19046 no. of SIS events found = 1244741-> Removing the following files with NEVENTS=0
ft940805_2305_0035G200370M.fits ft940805_2305_0035G200470H.fits ft940805_2305_0035G200570H.fits ft940805_2305_0035G201170M.fits ft940805_2305_0035G201270H.fits ft940805_2305_0035G201899.fits ft940805_2305_0035G202399.fits ft940805_2305_0035G202570H.fits ft940805_2305_0035G202670H.fits ft940805_2305_0035G202770H.fits ft940805_2305_0035G202870H.fits ft940805_2305_0035G203170H.fits ft940805_2305_0035G203370H.fits ft940805_2305_0035G203470H.fits ft940805_2305_0035G203570M.fits ft940805_2305_0035G203670H.fits ft940805_2305_0035G203770H.fits ft940805_2305_0035G204199.fits ft940805_2305_0035G204470H.fits ft940805_2305_0035G204570M.fits ft940805_2305_0035G204670H.fits ft940805_2305_0035G204770H.fits ft940805_2305_0035G204870H.fits ft940805_2305_0035G204970H.fits ft940805_2305_0035G205170H.fits ft940805_2305_0035G205270H.fits ft940805_2305_0035G205370M.fits ft940805_2305_0035G205470H.fits ft940805_2305_0035G205570H.fits ft940805_2305_0035G205970H.fits ft940805_2305_0035G206070H.fits ft940805_2305_0035G206170H.fits ft940805_2305_0035G206270H.fits ft940805_2305_0035G206873H.fits ft940805_2305_0035G207470M.fits ft940805_2305_0035G208070M.fits ft940805_2305_0035G208870M.fits ft940805_2305_0035G208970H.fits ft940805_2305_0035G209670M.fits ft940805_2305_0035G209770H.fits ft940805_2305_0035G210470H.fits ft940805_2305_0035G210570H.fits ft940805_2305_0035G210670M.fits ft940805_2305_0035G210799.fits ft940805_2305_0035G210870H.fits ft940805_2305_0035G210970H.fits ft940805_2305_0035G300370M.fits ft940805_2305_0035G300470H.fits ft940805_2305_0035G301170M.fits ft940805_2305_0035G301270H.fits ft940805_2305_0035G301370H.fits ft940805_2305_0035G301899.fits ft940805_2305_0035G301970M.fits ft940805_2305_0035G302399.fits ft940805_2305_0035G302570H.fits ft940805_2305_0035G302770H.fits ft940805_2305_0035G302870H.fits ft940805_2305_0035G302970H.fits ft940805_2305_0035G303070H.fits ft940805_2305_0035G303570H.fits ft940805_2305_0035G303670M.fits ft940805_2305_0035G303770H.fits ft940805_2305_0035G303870H.fits ft940805_2305_0035G304299.fits ft940805_2305_0035G304570H.fits ft940805_2305_0035G304670M.fits ft940805_2305_0035G304770H.fits ft940805_2305_0035G305270H.fits ft940805_2305_0035G305370H.fits ft940805_2305_0035G305470M.fits ft940805_2305_0035G305570H.fits ft940805_2305_0035G306270H.fits ft940805_2305_0035G306370H.fits ft940805_2305_0035G306470H.fits ft940805_2305_0035G306773H.fits ft940805_2305_0035G307370M.fits ft940805_2305_0035G307970M.fits ft940805_2305_0035G308770M.fits ft940805_2305_0035G308870H.fits ft940805_2305_0035G308970H.fits ft940805_2305_0035G309570M.fits ft940805_2305_0035G309670H.fits ft940805_2305_0035G309770H.fits ft940805_2305_0035G310370H.fits ft940805_2305_0035G310470H.fits ft940805_2305_0035G310570M.fits ft940805_2305_0035G310699.fits ft940805_2305_0035G310770H.fits ft940805_2305_0035G310870H.fits ft940805_2305_0035S000201M.fits ft940805_2305_0035S000401M.fits ft940805_2305_0035S000801M.fits ft940805_2305_0035S001299.fits ft940805_2305_0035S001699.fits ft940805_2305_0035S001901M.fits ft940805_2305_0035S002299.fits ft940805_2305_0035S002901M.fits ft940805_2305_0035S003299.fits ft940805_2305_0035S003701M.fits ft940805_2305_0035S004701M.fits ft940805_2305_0035S005301M.fits ft940805_2305_0035S005499.fits ft940805_2305_0035S005501H.fits ft940805_2305_0035S100201M.fits ft940805_2305_0035S100401M.fits ft940805_2305_0035S100801M.fits ft940805_2305_0035S101299.fits ft940805_2305_0035S101699.fits ft940805_2305_0035S101901M.fits ft940805_2305_0035S102299.fits ft940805_2305_0035S102901M.fits ft940805_2305_0035S103299.fits ft940805_2305_0035S103701M.fits ft940805_2305_0035S104701M.fits ft940805_2305_0035S105301M.fits ft940805_2305_0035S105499.fits ft940805_2305_0035S105501H.fits-> Checking for empty GTI extensions
ft940805_2305_0035S000101M.fits[3] ft940805_2305_0035S000301M.fits[3] ft940805_2305_0035S000501M.fits[3] ft940805_2305_0035S000601H.fits[3] ft940805_2305_0035S000701M.fits[3] ft940805_2305_0035S000901M.fits[3] ft940805_2305_0035S001001H.fits[3] ft940805_2305_0035S001101M.fits[3] ft940805_2305_0035S001301M.fits[3] ft940805_2305_0035S001401M.fits[3] ft940805_2305_0035S001501H.fits[3] ft940805_2305_0035S001701H.fits[3] ft940805_2305_0035S001801H.fits[3] ft940805_2305_0035S002001M.fits[3] ft940805_2305_0035S002101H.fits[3] ft940805_2305_0035S002301H.fits[3] ft940805_2305_0035S002401M.fits[3] ft940805_2305_0035S002501M.fits[3] ft940805_2305_0035S002601M.fits[3] ft940805_2305_0035S002701H.fits[3] ft940805_2305_0035S002801M.fits[3] ft940805_2305_0035S003001M.fits[3] ft940805_2305_0035S003101H.fits[3] ft940805_2305_0035S003301H.fits[3] ft940805_2305_0035S003401M.fits[3] ft940805_2305_0035S003501H.fits[3] ft940805_2305_0035S003601M.fits[3] ft940805_2305_0035S003801M.fits[3] ft940805_2305_0035S003901H.fits[3] ft940805_2305_0035S004001M.fits[3] ft940805_2305_0035S004101H.fits[3] ft940805_2305_0035S004201M.fits[3] ft940805_2305_0035S004301H.fits[3] ft940805_2305_0035S004401M.fits[3] ft940805_2305_0035S004501H.fits[3] ft940805_2305_0035S004601M.fits[3] ft940805_2305_0035S004801M.fits[3] ft940805_2305_0035S004901H.fits[3] ft940805_2305_0035S005001M.fits[3] ft940805_2305_0035S005101H.fits[3] ft940805_2305_0035S005201H.fits[3] ft940805_2305_0035S005601H.fits[3]-> Merging GTIs from the following files:
ft940805_2305_0035S100101M.fits[3] ft940805_2305_0035S100301M.fits[3] ft940805_2305_0035S100501M.fits[3] ft940805_2305_0035S100601H.fits[3] ft940805_2305_0035S100701M.fits[3] ft940805_2305_0035S100901M.fits[3] ft940805_2305_0035S101001H.fits[3] ft940805_2305_0035S101101M.fits[3] ft940805_2305_0035S101301M.fits[3] ft940805_2305_0035S101401M.fits[3] ft940805_2305_0035S101501H.fits[3] ft940805_2305_0035S101701H.fits[3] ft940805_2305_0035S101801H.fits[3] ft940805_2305_0035S102001M.fits[3] ft940805_2305_0035S102101H.fits[3] ft940805_2305_0035S102301H.fits[3] ft940805_2305_0035S102401M.fits[3] ft940805_2305_0035S102501M.fits[3] ft940805_2305_0035S102601M.fits[3] ft940805_2305_0035S102701H.fits[3] ft940805_2305_0035S102801M.fits[3] ft940805_2305_0035S103001M.fits[3] ft940805_2305_0035S103101H.fits[3] ft940805_2305_0035S103301H.fits[3] ft940805_2305_0035S103401M.fits[3] ft940805_2305_0035S103501H.fits[3] ft940805_2305_0035S103601M.fits[3] ft940805_2305_0035S103801M.fits[3] ft940805_2305_0035S103901H.fits[3] ft940805_2305_0035S104001M.fits[3] ft940805_2305_0035S104101H.fits[3] ft940805_2305_0035S104201M.fits[3] ft940805_2305_0035S104301H.fits[3] ft940805_2305_0035S104401M.fits[3] ft940805_2305_0035S104501H.fits[3] ft940805_2305_0035S104601M.fits[3] ft940805_2305_0035S104801M.fits[3] ft940805_2305_0035S104901H.fits[3] ft940805_2305_0035S105001M.fits[3] ft940805_2305_0035S105101H.fits[3] ft940805_2305_0035S105201H.fits[3] ft940805_2305_0035S105601H.fits[3]-> Merging GTIs from the following files:
ft940805_2305_0035G200170M.fits[3] ft940805_2305_0035G200270M.fits[3] ft940805_2305_0035G200670H.fits[3] ft940805_2305_0035G200770H.fits[3] ft940805_2305_0035G200870H.fits[3] ft940805_2305_0035G200970M.fits[3] ft940805_2305_0035G201070M.fits[3] ft940805_2305_0035G201370H.fits[3] ft940805_2305_0035G201470H.fits[3] ft940805_2305_0035G201570H.fits[3] ft940805_2305_0035G201670H.fits[3] ft940805_2305_0035G201770M.fits[3] ft940805_2305_0035G201970M.fits[3] ft940805_2305_0035G202070M.fits[3] ft940805_2305_0035G202170M.fits[3] ft940805_2305_0035G202270H.fits[3] ft940805_2305_0035G202470H.fits[3] ft940805_2305_0035G202970H.fits[3] ft940805_2305_0035G203070H.fits[3] ft940805_2305_0035G203270H.fits[3] ft940805_2305_0035G203870H.fits[3] ft940805_2305_0035G203970H.fits[3] ft940805_2305_0035G204070H.fits[3] ft940805_2305_0035G204270H.fits[3] ft940805_2305_0035G204370H.fits[3] ft940805_2305_0035G205070H.fits[3] ft940805_2305_0035G205670H.fits[3] ft940805_2305_0035G205770H.fits[3] ft940805_2305_0035G205870H.fits[3] ft940805_2305_0035G206370H.fits[3] ft940805_2305_0035G206470H.fits[3] ft940805_2305_0035G206570H.fits[3] ft940805_2305_0035G206670H.fits[3] ft940805_2305_0035G206770H.fits[3] ft940805_2305_0035G206970H.fits[3] ft940805_2305_0035G207070M.fits[3] ft940805_2305_0035G207170H.fits[3] ft940805_2305_0035G207270M.fits[3] ft940805_2305_0035G207370M.fits[3] ft940805_2305_0035G207570M.fits[3] ft940805_2305_0035G207670M.fits[3] ft940805_2305_0035G207770H.fits[3] ft940805_2305_0035G207870M.fits[3] ft940805_2305_0035G207970M.fits[3] ft940805_2305_0035G208170M.fits[3] ft940805_2305_0035G208270M.fits[3] ft940805_2305_0035G208370H.fits[3] ft940805_2305_0035G208470M.fits[3] ft940805_2305_0035G208570H.fits[3] ft940805_2305_0035G208670M.fits[3] ft940805_2305_0035G208770M.fits[3] ft940805_2305_0035G209070H.fits[3] ft940805_2305_0035G209170H.fits[3] ft940805_2305_0035G209270H.fits[3] ft940805_2305_0035G209370H.fits[3] ft940805_2305_0035G209470M.fits[3] ft940805_2305_0035G209570M.fits[3] ft940805_2305_0035G209870H.fits[3] ft940805_2305_0035G209970H.fits[3] ft940805_2305_0035G210070H.fits[3] ft940805_2305_0035G210170H.fits[3] ft940805_2305_0035G210270M.fits[3] ft940805_2305_0035G210370H.fits[3] ft940805_2305_0035G211070H.fits[3] ft940805_2305_0035G211170H.fits[3] ft940805_2305_0035G211270H.fits[3]-> Merging GTIs from the following files:
ft940805_2305_0035G300170M.fits[3] ft940805_2305_0035G300270M.fits[3] ft940805_2305_0035G300570H.fits[3] ft940805_2305_0035G300670H.fits[3] ft940805_2305_0035G300770H.fits[3] ft940805_2305_0035G300870H.fits[3] ft940805_2305_0035G300970M.fits[3] ft940805_2305_0035G301070M.fits[3] ft940805_2305_0035G301470H.fits[3] ft940805_2305_0035G301570H.fits[3] ft940805_2305_0035G301670H.fits[3] ft940805_2305_0035G301770M.fits[3] ft940805_2305_0035G302070M.fits[3] ft940805_2305_0035G302170M.fits[3] ft940805_2305_0035G302270H.fits[3] ft940805_2305_0035G302470H.fits[3] ft940805_2305_0035G302670H.fits[3] ft940805_2305_0035G303170H.fits[3] ft940805_2305_0035G303270H.fits[3] ft940805_2305_0035G303370H.fits[3] ft940805_2305_0035G303470H.fits[3] ft940805_2305_0035G303970H.fits[3] ft940805_2305_0035G304070H.fits[3] ft940805_2305_0035G304170H.fits[3] ft940805_2305_0035G304370H.fits[3] ft940805_2305_0035G304470H.fits[3] ft940805_2305_0035G304870H.fits[3] ft940805_2305_0035G304970H.fits[3] ft940805_2305_0035G305070H.fits[3] ft940805_2305_0035G305170H.fits[3] ft940805_2305_0035G305670H.fits[3] ft940805_2305_0035G305770H.fits[3] ft940805_2305_0035G305870H.fits[3] ft940805_2305_0035G305970H.fits[3] ft940805_2305_0035G306070H.fits[3] ft940805_2305_0035G306170H.fits[3] ft940805_2305_0035G306570H.fits[3] ft940805_2305_0035G306670H.fits[3] ft940805_2305_0035G306870H.fits[3] ft940805_2305_0035G306970M.fits[3] ft940805_2305_0035G307070H.fits[3] ft940805_2305_0035G307170M.fits[3] ft940805_2305_0035G307270M.fits[3] ft940805_2305_0035G307470M.fits[3] ft940805_2305_0035G307570M.fits[3] ft940805_2305_0035G307670H.fits[3] ft940805_2305_0035G307770M.fits[3] ft940805_2305_0035G307870M.fits[3] ft940805_2305_0035G308070M.fits[3] ft940805_2305_0035G308170M.fits[3] ft940805_2305_0035G308270H.fits[3] ft940805_2305_0035G308370M.fits[3] ft940805_2305_0035G308470H.fits[3] ft940805_2305_0035G308570M.fits[3] ft940805_2305_0035G308670M.fits[3] ft940805_2305_0035G309070H.fits[3] ft940805_2305_0035G309170H.fits[3] ft940805_2305_0035G309270H.fits[3] ft940805_2305_0035G309370M.fits[3] ft940805_2305_0035G309470M.fits[3] ft940805_2305_0035G309870H.fits[3] ft940805_2305_0035G309970H.fits[3] ft940805_2305_0035G310070H.fits[3] ft940805_2305_0035G310170M.fits[3] ft940805_2305_0035G310270H.fits[3] ft940805_2305_0035G310970H.fits[3] ft940805_2305_0035G311070H.fits[3] ft940805_2305_0035G311170H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 3 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 7 photon cnt = 19 GISSORTSPLIT:LO:g200570h.prelist merge count = 7 photon cnt = 11 GISSORTSPLIT:LO:g200670h.prelist merge count = 18 photon cnt = 29752 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200870h.prelist merge count = 2 photon cnt = 11 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 363 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270m.prelist merge count = 6 photon cnt = 29 GISSORTSPLIT:LO:g200370m.prelist merge count = 3 photon cnt = 20 GISSORTSPLIT:LO:g200470m.prelist merge count = 13 photon cnt = 39189 GISSORTSPLIT:LO:Total filenames split = 66 GISSORTSPLIT:LO:Total split file cnt = 15 GISSORTSPLIT:LO:End program-> Creating ad82034000g200170m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035G200170M.fits 2 -- ft940805_2305_0035G200970M.fits 3 -- ft940805_2305_0035G201770M.fits 4 -- ft940805_2305_0035G202170M.fits 5 -- ft940805_2305_0035G207070M.fits 6 -- ft940805_2305_0035G207270M.fits 7 -- ft940805_2305_0035G207670M.fits 8 -- ft940805_2305_0035G207870M.fits 9 -- ft940805_2305_0035G208270M.fits 10 -- ft940805_2305_0035G208470M.fits 11 -- ft940805_2305_0035G208670M.fits 12 -- ft940805_2305_0035G209470M.fits 13 -- ft940805_2305_0035G210270M.fits Merging binary extension #: 2 1 -- ft940805_2305_0035G200170M.fits 2 -- ft940805_2305_0035G200970M.fits 3 -- ft940805_2305_0035G201770M.fits 4 -- ft940805_2305_0035G202170M.fits 5 -- ft940805_2305_0035G207070M.fits 6 -- ft940805_2305_0035G207270M.fits 7 -- ft940805_2305_0035G207670M.fits 8 -- ft940805_2305_0035G207870M.fits 9 -- ft940805_2305_0035G208270M.fits 10 -- ft940805_2305_0035G208470M.fits 11 -- ft940805_2305_0035G208670M.fits 12 -- ft940805_2305_0035G209470M.fits 13 -- ft940805_2305_0035G210270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad82034000g200270h.unf
---- cmerge: version 1.5 ---- A total of 18 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035G200870H.fits 2 -- ft940805_2305_0035G201670H.fits 3 -- ft940805_2305_0035G202270H.fits 4 -- ft940805_2305_0035G202470H.fits 5 -- ft940805_2305_0035G203270H.fits 6 -- ft940805_2305_0035G204070H.fits 7 -- ft940805_2305_0035G204270H.fits 8 -- ft940805_2305_0035G205070H.fits 9 -- ft940805_2305_0035G205870H.fits 10 -- ft940805_2305_0035G206770H.fits 11 -- ft940805_2305_0035G207170H.fits 12 -- ft940805_2305_0035G207770H.fits 13 -- ft940805_2305_0035G208370H.fits 14 -- ft940805_2305_0035G208570H.fits 15 -- ft940805_2305_0035G209370H.fits 16 -- ft940805_2305_0035G210170H.fits 17 -- ft940805_2305_0035G210370H.fits 18 -- ft940805_2305_0035G211270H.fits Merging binary extension #: 2 1 -- ft940805_2305_0035G200870H.fits 2 -- ft940805_2305_0035G201670H.fits 3 -- ft940805_2305_0035G202270H.fits 4 -- ft940805_2305_0035G202470H.fits 5 -- ft940805_2305_0035G203270H.fits 6 -- ft940805_2305_0035G204070H.fits 7 -- ft940805_2305_0035G204270H.fits 8 -- ft940805_2305_0035G205070H.fits 9 -- ft940805_2305_0035G205870H.fits 10 -- ft940805_2305_0035G206770H.fits 11 -- ft940805_2305_0035G207170H.fits 12 -- ft940805_2305_0035G207770H.fits 13 -- ft940805_2305_0035G208370H.fits 14 -- ft940805_2305_0035G208570H.fits 15 -- ft940805_2305_0035G209370H.fits 16 -- ft940805_2305_0035G210170H.fits 17 -- ft940805_2305_0035G210370H.fits 18 -- ft940805_2305_0035G211270H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000363 events
ft940805_2305_0035G206970H.fits-> Ignoring the following files containing 000000029 events
ft940805_2305_0035G200270M.fits ft940805_2305_0035G201070M.fits ft940805_2305_0035G207370M.fits ft940805_2305_0035G207970M.fits ft940805_2305_0035G208770M.fits ft940805_2305_0035G209570M.fits-> Ignoring the following files containing 000000020 events
ft940805_2305_0035G202070M.fits ft940805_2305_0035G207570M.fits ft940805_2305_0035G208170M.fits-> Ignoring the following files containing 000000019 events
ft940805_2305_0035G200670H.fits ft940805_2305_0035G201470H.fits ft940805_2305_0035G203870H.fits ft940805_2305_0035G205670H.fits ft940805_2305_0035G209170H.fits ft940805_2305_0035G209970H.fits ft940805_2305_0035G211070H.fits-> Ignoring the following files containing 000000011 events
ft940805_2305_0035G203070H.fits ft940805_2305_0035G206570H.fits-> Ignoring the following files containing 000000011 events
ft940805_2305_0035G200770H.fits ft940805_2305_0035G201570H.fits ft940805_2305_0035G203970H.fits ft940805_2305_0035G205770H.fits ft940805_2305_0035G209270H.fits ft940805_2305_0035G210070H.fits ft940805_2305_0035G211170H.fits-> Ignoring the following files containing 000000003 events
ft940805_2305_0035G202970H.fits-> Ignoring the following files containing 000000003 events
ft940805_2305_0035G201370H.fits ft940805_2305_0035G209070H.fits ft940805_2305_0035G209870H.fits-> Ignoring the following files containing 000000002 events
ft940805_2305_0035G206670H.fits-> Ignoring the following files containing 000000002 events
ft940805_2305_0035G206470H.fits-> Ignoring the following files containing 000000001 events
ft940805_2305_0035G204370H.fits-> Ignoring the following files containing 000000001 events
ft940805_2305_0035G201970M.fits-> Ignoring the following files containing 000000001 events
ft940805_2305_0035G206370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300470h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g300570h.prelist merge count = 8 photon cnt = 18 GISSORTSPLIT:LO:g300670h.prelist merge count = 8 photon cnt = 19 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300870h.prelist merge count = 18 photon cnt = 29378 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301070h.prelist merge count = 2 photon cnt = 15 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 420 GISSORTSPLIT:LO:g300170m.prelist merge count = 6 photon cnt = 31 GISSORTSPLIT:LO:g300270m.prelist merge count = 3 photon cnt = 25 GISSORTSPLIT:LO:g300370m.prelist merge count = 13 photon cnt = 38058 GISSORTSPLIT:LO:Total filenames split = 68 GISSORTSPLIT:LO:Total split file cnt = 14 GISSORTSPLIT:LO:End program-> Creating ad82034000g300170m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035G300170M.fits 2 -- ft940805_2305_0035G300970M.fits 3 -- ft940805_2305_0035G301770M.fits 4 -- ft940805_2305_0035G302170M.fits 5 -- ft940805_2305_0035G306970M.fits 6 -- ft940805_2305_0035G307170M.fits 7 -- ft940805_2305_0035G307570M.fits 8 -- ft940805_2305_0035G307770M.fits 9 -- ft940805_2305_0035G308170M.fits 10 -- ft940805_2305_0035G308370M.fits 11 -- ft940805_2305_0035G308570M.fits 12 -- ft940805_2305_0035G309370M.fits 13 -- ft940805_2305_0035G310170M.fits Merging binary extension #: 2 1 -- ft940805_2305_0035G300170M.fits 2 -- ft940805_2305_0035G300970M.fits 3 -- ft940805_2305_0035G301770M.fits 4 -- ft940805_2305_0035G302170M.fits 5 -- ft940805_2305_0035G306970M.fits 6 -- ft940805_2305_0035G307170M.fits 7 -- ft940805_2305_0035G307570M.fits 8 -- ft940805_2305_0035G307770M.fits 9 -- ft940805_2305_0035G308170M.fits 10 -- ft940805_2305_0035G308370M.fits 11 -- ft940805_2305_0035G308570M.fits 12 -- ft940805_2305_0035G309370M.fits 13 -- ft940805_2305_0035G310170M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad82034000g300270h.unf
---- cmerge: version 1.5 ---- A total of 18 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035G300870H.fits 2 -- ft940805_2305_0035G301670H.fits 3 -- ft940805_2305_0035G302270H.fits 4 -- ft940805_2305_0035G302470H.fits 5 -- ft940805_2305_0035G303370H.fits 6 -- ft940805_2305_0035G304170H.fits 7 -- ft940805_2305_0035G304370H.fits 8 -- ft940805_2305_0035G305170H.fits 9 -- ft940805_2305_0035G305970H.fits 10 -- ft940805_2305_0035G306670H.fits 11 -- ft940805_2305_0035G307070H.fits 12 -- ft940805_2305_0035G307670H.fits 13 -- ft940805_2305_0035G308270H.fits 14 -- ft940805_2305_0035G308470H.fits 15 -- ft940805_2305_0035G309270H.fits 16 -- ft940805_2305_0035G310070H.fits 17 -- ft940805_2305_0035G310270H.fits 18 -- ft940805_2305_0035G311170H.fits Merging binary extension #: 2 1 -- ft940805_2305_0035G300870H.fits 2 -- ft940805_2305_0035G301670H.fits 3 -- ft940805_2305_0035G302270H.fits 4 -- ft940805_2305_0035G302470H.fits 5 -- ft940805_2305_0035G303370H.fits 6 -- ft940805_2305_0035G304170H.fits 7 -- ft940805_2305_0035G304370H.fits 8 -- ft940805_2305_0035G305170H.fits 9 -- ft940805_2305_0035G305970H.fits 10 -- ft940805_2305_0035G306670H.fits 11 -- ft940805_2305_0035G307070H.fits 12 -- ft940805_2305_0035G307670H.fits 13 -- ft940805_2305_0035G308270H.fits 14 -- ft940805_2305_0035G308470H.fits 15 -- ft940805_2305_0035G309270H.fits 16 -- ft940805_2305_0035G310070H.fits 17 -- ft940805_2305_0035G310270H.fits 18 -- ft940805_2305_0035G311170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000420 events
ft940805_2305_0035G306870H.fits-> Ignoring the following files containing 000000031 events
ft940805_2305_0035G300270M.fits ft940805_2305_0035G301070M.fits ft940805_2305_0035G307270M.fits ft940805_2305_0035G307870M.fits ft940805_2305_0035G308670M.fits ft940805_2305_0035G309470M.fits-> Ignoring the following files containing 000000025 events
ft940805_2305_0035G302070M.fits ft940805_2305_0035G307470M.fits ft940805_2305_0035G308070M.fits-> Ignoring the following files containing 000000019 events
ft940805_2305_0035G300770H.fits ft940805_2305_0035G301570H.fits ft940805_2305_0035G304070H.fits ft940805_2305_0035G305070H.fits ft940805_2305_0035G305870H.fits ft940805_2305_0035G309170H.fits ft940805_2305_0035G309970H.fits ft940805_2305_0035G311070H.fits-> Ignoring the following files containing 000000018 events
ft940805_2305_0035G300670H.fits ft940805_2305_0035G301470H.fits ft940805_2305_0035G303970H.fits ft940805_2305_0035G304970H.fits ft940805_2305_0035G305770H.fits ft940805_2305_0035G309070H.fits ft940805_2305_0035G309870H.fits ft940805_2305_0035G310970H.fits-> Ignoring the following files containing 000000015 events
ft940805_2305_0035G302670H.fits ft940805_2305_0035G306070H.fits-> Ignoring the following files containing 000000007 events
ft940805_2305_0035G300570H.fits ft940805_2305_0035G304870H.fits ft940805_2305_0035G305670H.fits-> Ignoring the following files containing 000000006 events
ft940805_2305_0035G306570H.fits-> Ignoring the following files containing 000000005 events
ft940805_2305_0035G303470H.fits ft940805_2305_0035G304470H.fits-> Ignoring the following files containing 000000003 events
ft940805_2305_0035G303170H.fits-> Ignoring the following files containing 000000002 events
ft940805_2305_0035G303270H.fits-> Ignoring the following files containing 000000002 events
ft940805_2305_0035G306170H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 17 photon cnt = 356388 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 2 photon cnt = 365 SIS0SORTSPLIT:LO:s000301m.prelist merge count = 21 photon cnt = 226738 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 2 photon cnt = 64 SIS0SORTSPLIT:LO:Total filenames split = 42 SIS0SORTSPLIT:LO:Total split file cnt = 4 SIS0SORTSPLIT:LO:End program-> Creating ad82034000s000101h.unf
---- cmerge: version 1.5 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035S000601H.fits 2 -- ft940805_2305_0035S001001H.fits 3 -- ft940805_2305_0035S001501H.fits 4 -- ft940805_2305_0035S001701H.fits 5 -- ft940805_2305_0035S002101H.fits 6 -- ft940805_2305_0035S002301H.fits 7 -- ft940805_2305_0035S002701H.fits 8 -- ft940805_2305_0035S003101H.fits 9 -- ft940805_2305_0035S003301H.fits 10 -- ft940805_2305_0035S003501H.fits 11 -- ft940805_2305_0035S003901H.fits 12 -- ft940805_2305_0035S004101H.fits 13 -- ft940805_2305_0035S004301H.fits 14 -- ft940805_2305_0035S004501H.fits 15 -- ft940805_2305_0035S004901H.fits 16 -- ft940805_2305_0035S005101H.fits 17 -- ft940805_2305_0035S005601H.fits Merging binary extension #: 2 1 -- ft940805_2305_0035S000601H.fits 2 -- ft940805_2305_0035S001001H.fits 3 -- ft940805_2305_0035S001501H.fits 4 -- ft940805_2305_0035S001701H.fits 5 -- ft940805_2305_0035S002101H.fits 6 -- ft940805_2305_0035S002301H.fits 7 -- ft940805_2305_0035S002701H.fits 8 -- ft940805_2305_0035S003101H.fits 9 -- ft940805_2305_0035S003301H.fits 10 -- ft940805_2305_0035S003501H.fits 11 -- ft940805_2305_0035S003901H.fits 12 -- ft940805_2305_0035S004101H.fits 13 -- ft940805_2305_0035S004301H.fits 14 -- ft940805_2305_0035S004501H.fits 15 -- ft940805_2305_0035S004901H.fits 16 -- ft940805_2305_0035S005101H.fits 17 -- ft940805_2305_0035S005601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad82034000s000201m.unf
---- cmerge: version 1.5 ---- A total of 21 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035S000101M.fits 2 -- ft940805_2305_0035S000301M.fits 3 -- ft940805_2305_0035S000501M.fits 4 -- ft940805_2305_0035S000701M.fits 5 -- ft940805_2305_0035S000901M.fits 6 -- ft940805_2305_0035S001101M.fits 7 -- ft940805_2305_0035S001401M.fits 8 -- ft940805_2305_0035S002001M.fits 9 -- ft940805_2305_0035S002401M.fits 10 -- ft940805_2305_0035S002601M.fits 11 -- ft940805_2305_0035S002801M.fits 12 -- ft940805_2305_0035S003001M.fits 13 -- ft940805_2305_0035S003401M.fits 14 -- ft940805_2305_0035S003601M.fits 15 -- ft940805_2305_0035S003801M.fits 16 -- ft940805_2305_0035S004001M.fits 17 -- ft940805_2305_0035S004201M.fits 18 -- ft940805_2305_0035S004401M.fits 19 -- ft940805_2305_0035S004601M.fits 20 -- ft940805_2305_0035S004801M.fits 21 -- ft940805_2305_0035S005001M.fits Merging binary extension #: 2 1 -- ft940805_2305_0035S000101M.fits 2 -- ft940805_2305_0035S000301M.fits 3 -- ft940805_2305_0035S000501M.fits 4 -- ft940805_2305_0035S000701M.fits 5 -- ft940805_2305_0035S000901M.fits 6 -- ft940805_2305_0035S001101M.fits 7 -- ft940805_2305_0035S001401M.fits 8 -- ft940805_2305_0035S002001M.fits 9 -- ft940805_2305_0035S002401M.fits 10 -- ft940805_2305_0035S002601M.fits 11 -- ft940805_2305_0035S002801M.fits 12 -- ft940805_2305_0035S003001M.fits 13 -- ft940805_2305_0035S003401M.fits 14 -- ft940805_2305_0035S003601M.fits 15 -- ft940805_2305_0035S003801M.fits 16 -- ft940805_2305_0035S004001M.fits 17 -- ft940805_2305_0035S004201M.fits 18 -- ft940805_2305_0035S004401M.fits 19 -- ft940805_2305_0035S004601M.fits 20 -- ft940805_2305_0035S004801M.fits 21 -- ft940805_2305_0035S005001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000365 events
ft940805_2305_0035S001801H.fits ft940805_2305_0035S005201H.fits-> Ignoring the following files containing 000000064 events
ft940805_2305_0035S001301M.fits ft940805_2305_0035S002501M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 17 photon cnt = 355691 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 2 photon cnt = 389 SIS1SORTSPLIT:LO:s100301m.prelist merge count = 21 photon cnt = 305042 SIS1SORTSPLIT:LO:s100401m.prelist merge count = 2 photon cnt = 64 SIS1SORTSPLIT:LO:Total filenames split = 42 SIS1SORTSPLIT:LO:Total split file cnt = 4 SIS1SORTSPLIT:LO:End program-> Creating ad82034000s100101h.unf
---- cmerge: version 1.5 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035S100601H.fits 2 -- ft940805_2305_0035S101001H.fits 3 -- ft940805_2305_0035S101501H.fits 4 -- ft940805_2305_0035S101701H.fits 5 -- ft940805_2305_0035S102101H.fits 6 -- ft940805_2305_0035S102301H.fits 7 -- ft940805_2305_0035S102701H.fits 8 -- ft940805_2305_0035S103101H.fits 9 -- ft940805_2305_0035S103301H.fits 10 -- ft940805_2305_0035S103501H.fits 11 -- ft940805_2305_0035S103901H.fits 12 -- ft940805_2305_0035S104101H.fits 13 -- ft940805_2305_0035S104301H.fits 14 -- ft940805_2305_0035S104501H.fits 15 -- ft940805_2305_0035S104901H.fits 16 -- ft940805_2305_0035S105101H.fits 17 -- ft940805_2305_0035S105601H.fits Merging binary extension #: 2 1 -- ft940805_2305_0035S100601H.fits 2 -- ft940805_2305_0035S101001H.fits 3 -- ft940805_2305_0035S101501H.fits 4 -- ft940805_2305_0035S101701H.fits 5 -- ft940805_2305_0035S102101H.fits 6 -- ft940805_2305_0035S102301H.fits 7 -- ft940805_2305_0035S102701H.fits 8 -- ft940805_2305_0035S103101H.fits 9 -- ft940805_2305_0035S103301H.fits 10 -- ft940805_2305_0035S103501H.fits 11 -- ft940805_2305_0035S103901H.fits 12 -- ft940805_2305_0035S104101H.fits 13 -- ft940805_2305_0035S104301H.fits 14 -- ft940805_2305_0035S104501H.fits 15 -- ft940805_2305_0035S104901H.fits 16 -- ft940805_2305_0035S105101H.fits 17 -- ft940805_2305_0035S105601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad82034000s100201m.unf
---- cmerge: version 1.5 ---- A total of 21 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940805_2305_0035S100101M.fits 2 -- ft940805_2305_0035S100301M.fits 3 -- ft940805_2305_0035S100501M.fits 4 -- ft940805_2305_0035S100701M.fits 5 -- ft940805_2305_0035S100901M.fits 6 -- ft940805_2305_0035S101101M.fits 7 -- ft940805_2305_0035S101401M.fits 8 -- ft940805_2305_0035S102001M.fits 9 -- ft940805_2305_0035S102401M.fits 10 -- ft940805_2305_0035S102601M.fits 11 -- ft940805_2305_0035S102801M.fits 12 -- ft940805_2305_0035S103001M.fits 13 -- ft940805_2305_0035S103401M.fits 14 -- ft940805_2305_0035S103601M.fits 15 -- ft940805_2305_0035S103801M.fits 16 -- ft940805_2305_0035S104001M.fits 17 -- ft940805_2305_0035S104201M.fits 18 -- ft940805_2305_0035S104401M.fits 19 -- ft940805_2305_0035S104601M.fits 20 -- ft940805_2305_0035S104801M.fits 21 -- ft940805_2305_0035S105001M.fits Merging binary extension #: 2 1 -- ft940805_2305_0035S100101M.fits 2 -- ft940805_2305_0035S100301M.fits 3 -- ft940805_2305_0035S100501M.fits 4 -- ft940805_2305_0035S100701M.fits 5 -- ft940805_2305_0035S100901M.fits 6 -- ft940805_2305_0035S101101M.fits 7 -- ft940805_2305_0035S101401M.fits 8 -- ft940805_2305_0035S102001M.fits 9 -- ft940805_2305_0035S102401M.fits 10 -- ft940805_2305_0035S102601M.fits 11 -- ft940805_2305_0035S102801M.fits 12 -- ft940805_2305_0035S103001M.fits 13 -- ft940805_2305_0035S103401M.fits 14 -- ft940805_2305_0035S103601M.fits 15 -- ft940805_2305_0035S103801M.fits 16 -- ft940805_2305_0035S104001M.fits 17 -- ft940805_2305_0035S104201M.fits 18 -- ft940805_2305_0035S104401M.fits 19 -- ft940805_2305_0035S104601M.fits 20 -- ft940805_2305_0035S104801M.fits 21 -- ft940805_2305_0035S105001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000389 events
ft940805_2305_0035S101801H.fits ft940805_2305_0035S105201H.fits-> Ignoring the following files containing 000000064 events
ft940805_2305_0035S101301M.fits ft940805_2305_0035S102501M.fits-> Tar-ing together the leftover raw files
a ft940805_2305_0035G200270M.fits 40K a ft940805_2305_0035G200670H.fits 40K a ft940805_2305_0035G200770H.fits 40K a ft940805_2305_0035G201070M.fits 40K a ft940805_2305_0035G201370H.fits 40K a ft940805_2305_0035G201470H.fits 40K a ft940805_2305_0035G201570H.fits 40K a ft940805_2305_0035G201970M.fits 40K a ft940805_2305_0035G202070M.fits 40K a ft940805_2305_0035G202970H.fits 40K a ft940805_2305_0035G203070H.fits 40K a ft940805_2305_0035G203870H.fits 40K a ft940805_2305_0035G203970H.fits 40K a ft940805_2305_0035G204370H.fits 40K a ft940805_2305_0035G205670H.fits 40K a ft940805_2305_0035G205770H.fits 40K a ft940805_2305_0035G206370H.fits 40K a ft940805_2305_0035G206470H.fits 40K a ft940805_2305_0035G206570H.fits 40K a ft940805_2305_0035G206670H.fits 40K a ft940805_2305_0035G206970H.fits 48K a ft940805_2305_0035G207370M.fits 40K a ft940805_2305_0035G207570M.fits 40K a ft940805_2305_0035G207970M.fits 40K a ft940805_2305_0035G208170M.fits 40K a ft940805_2305_0035G208770M.fits 40K a ft940805_2305_0035G209070H.fits 40K a ft940805_2305_0035G209170H.fits 40K a ft940805_2305_0035G209270H.fits 40K a ft940805_2305_0035G209570M.fits 40K a ft940805_2305_0035G209870H.fits 40K a ft940805_2305_0035G209970H.fits 40K a ft940805_2305_0035G210070H.fits 40K a ft940805_2305_0035G211070H.fits 40K a ft940805_2305_0035G211170H.fits 40K a ft940805_2305_0035G300270M.fits 40K a ft940805_2305_0035G300570H.fits 40K a ft940805_2305_0035G300670H.fits 40K a ft940805_2305_0035G300770H.fits 40K a ft940805_2305_0035G301070M.fits 40K a ft940805_2305_0035G301470H.fits 40K a ft940805_2305_0035G301570H.fits 40K a ft940805_2305_0035G302070M.fits 40K a ft940805_2305_0035G302670H.fits 40K a ft940805_2305_0035G303170H.fits 40K a ft940805_2305_0035G303270H.fits 40K a ft940805_2305_0035G303470H.fits 40K a ft940805_2305_0035G303970H.fits 40K a ft940805_2305_0035G304070H.fits 40K a ft940805_2305_0035G304470H.fits 40K a ft940805_2305_0035G304870H.fits 40K a ft940805_2305_0035G304970H.fits 40K a ft940805_2305_0035G305070H.fits 40K a ft940805_2305_0035G305670H.fits 40K a ft940805_2305_0035G305770H.fits 40K a ft940805_2305_0035G305870H.fits 40K a ft940805_2305_0035G306070H.fits 40K a ft940805_2305_0035G306170H.fits 40K a ft940805_2305_0035G306570H.fits 40K a ft940805_2305_0035G306870H.fits 51K a ft940805_2305_0035G307270M.fits 40K a ft940805_2305_0035G307470M.fits 40K a ft940805_2305_0035G307870M.fits 40K a ft940805_2305_0035G308070M.fits 40K a ft940805_2305_0035G308670M.fits 40K a ft940805_2305_0035G309070H.fits 40K a ft940805_2305_0035G309170H.fits 40K a ft940805_2305_0035G309470M.fits 40K a ft940805_2305_0035G309870H.fits 40K a ft940805_2305_0035G309970H.fits 40K a ft940805_2305_0035G310970H.fits 40K a ft940805_2305_0035G311070H.fits 40K a ft940805_2305_0035S001301M.fits 40K a ft940805_2305_0035S001801H.fits 43K a ft940805_2305_0035S002501M.fits 40K a ft940805_2305_0035S005201H.fits 48K a ft940805_2305_0035S101301M.fits 40K a ft940805_2305_0035S101801H.fits 43K a ft940805_2305_0035S102501M.fits 40K a ft940805_2305_0035S105201H.fits 48K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft940805_2305.0035 'ft940805_2305.0035' is successfully opened Data Start Time is 50281509.44 (940805 230509) Time Margin 2.0 sec included Sync error detected in 9853 th SF 'ft940805_2305.0035' EOF detected, sf=19046 Data End Time is 50373359.16 (940807 003559) Gain History is written in ft940805_2305_0035.ghf-> Checking if column CAL_START in ft940805_2305_0035.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft940805_2305_0035.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad82034000g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000201m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s000212m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100201m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad82034000s100212m.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 94/ 8/ 5 23: 5 mjd=49569.961806 Orbit file name is ./frf.orbit.214 Epoch of Orbital Elements: 1994/8/1 11:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa940805_2305.0035 S0-HK file: ft940805_2305_0035S0HK.fits S1-HK file: ft940805_2305_0035S1HK.fits G2-HK file: ft940805_2305_0035G2HK.fits G3-HK file: ft940805_2305_0035G3HK.fits output FITS File: ft940805_2305_0035.mkf Total 2871 Data bins were processed.-> Checking if column TIME in ft940805_2305_0035.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 11714.629 The mean of the selected column is 22.484892 The standard deviation of the selected column is 10.056494 The minimum of selected column is 5.4062662 The maximum of selected column is 105.84406 The number of points used in calculation is 521-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<52.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.31E+05 60976 0100
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
58266 35570 0 22696 0 0
Writing events file
35570 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
58266 35570 0 22696 0 0
in 16869.30 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 35570
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 13 29157
Flickering pixels iter, pixels & cnts : 1 11 195
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 24
Number of (internal) image counts : 35570
Number of image cts rejected (N, %) : 29352 82.5189743
By chip : 0 1 2 3
Pixels rejected : 0 24 0 0
Image counts : 0 35570 0 0
Image cts rejected: 0 29352 0 0
Image cts rej (%) : 0.00 82.52 0.00 0.00
filtering data...
Total counts : 0 35570 0 0
Total cts rejected: 0 29352 0 0
Total cts rej (%) : 0.00 82.52 0.00 0.00
Number of clean counts accepted : 6218
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 24
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad82034000s000102h.evt use_events=no
Wrote cleaned events file to ad82034000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad82034000s000112h.unf into ad82034000s000112h.evtThe sum of the selected column is 11714.629 The mean of the selected column is 22.484892 The standard deviation of the selected column is 10.056494 The minimum of selected column is 5.4062662 The maximum of selected column is 105.84406 The number of points used in calculation is 521-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<52.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.31E+05 61478 0100
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
58475 35666 0 22809 0 0
Writing events file
35666 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
58475 35666 0 22809 0 0
in 16869.30 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 35666
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 13 29157
Flickering pixels iter, pixels & cnts : 1 11 195
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 24
Number of (internal) image counts : 35666
Number of image cts rejected (N, %) : 29352 82.2968674
By chip : 0 1 2 3
Pixels rejected : 0 24 0 0
Image counts : 0 35666 0 0
Image cts rejected: 0 29352 0 0
Image cts rej (%) : 0.00 82.30 0.00 0.00
filtering data...
Total counts : 0 35666 0 0
Total cts rejected: 0 29352 0 0
Total cts rej (%) : 0.00 82.30 0.00 0.00
Number of clean counts accepted : 6314
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 24
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad82034000s000112h.evt use_events=no
Wrote cleaned events file to ad82034000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad82034000s000201m.unf because of modeThe sum of the selected column is 11855.483 The mean of the selected column is 24.698924 The standard deviation of the selected column is 10.569656 The minimum of selected column is 6.0416789 The maximum of selected column is 71.437714 The number of points used in calculation is 480-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<56.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.45E+05 88514 0100
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
85639 40005 0 45634 0 0
Writing events file
40005 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
85639 40005 0 45634 0 0
in 15664.15 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 40005
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 16 33967
Flickering pixels iter, pixels & cnts : 1 16 372
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 32
Number of (internal) image counts : 40005
Number of image cts rejected (N, %) : 34339 85.8367691
By chip : 0 1 2 3
Pixels rejected : 0 32 0 0
Image counts : 0 40005 0 0
Image cts rejected: 0 34339 0 0
Image cts rej (%) : 0.00 85.84 0.00 0.00
filtering data...
Total counts : 0 40005 0 0
Total cts rejected: 0 34339 0 0
Total cts rej (%) : 0.00 85.84 0.00 0.00
Number of clean counts accepted : 5666
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad82034000s000202m.evt use_events=no
Wrote cleaned events file to ad82034000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad82034000s000212m.unf into ad82034000s000212m.evtThe sum of the selected column is 11855.483 The mean of the selected column is 24.698924 The standard deviation of the selected column is 10.569656 The minimum of selected column is 6.0416789 The maximum of selected column is 71.437714 The number of points used in calculation is 480-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<56.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.45E+05 89238 0100
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s000212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
85906 40107 0 45799 0 0
Writing events file
40107 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
85906 40107 0 45799 0 0
in 15664.15 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 40107
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 16 33967
Flickering pixels iter, pixels & cnts : 1 16 372
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 32
Number of (internal) image counts : 40107
Number of image cts rejected (N, %) : 34339 85.6184692
By chip : 0 1 2 3
Pixels rejected : 0 32 0 0
Image counts : 0 40107 0 0
Image cts rejected: 0 34339 0 0
Image cts rej (%) : 0.00 85.62 0.00 0.00
filtering data...
Total counts : 0 40107 0 0
Total cts rejected: 0 34339 0 0
Total cts rej (%) : 0.00 85.62 0.00 0.00
Number of clean counts accepted : 5768
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad82034000s000212m.evt use_events=no
Wrote cleaned events file to ad82034000s000212m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad82034000s100101h.unf because of modeThe sum of the selected column is 20770.345 The mean of the selected column is 39.638062 The standard deviation of the selected column is 17.726544 The minimum of selected column is 11.781286 The maximum of selected column is 186.68805 The number of points used in calculation is 524-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<92.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.31E+05 125167 0001
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
120854 71498 0 49356 0 0
Writing events file
71498 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
120854 71498 0 49356 0 0
in 16923.09 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 71498
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 27 65895
Flickering pixels iter, pixels & cnts : 1 17 422
Number of pixels rejected : 44
Number of (internal) image counts : 71498
Number of image cts rejected (N, %) : 66317 92.7536469
By chip : 0 1 2 3
Pixels rejected : 0 0 0 44
Image counts : 0 0 0 71498
Image cts rejected: 0 0 0 66317
Image cts rej (%) : 0.00 0.00 0.00 92.75
filtering data...
Total counts : 0 0 0 71498
Total cts rejected: 0 0 0 66317
Total cts rej (%) : 0.00 0.00 0.00 92.75
Number of clean counts accepted : 5181
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 44
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad82034000s100102h.evt use_events=no
Wrote cleaned events file to ad82034000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad82034000s100112h.unf into ad82034000s100112h.evtThe sum of the selected column is 20770.345 The mean of the selected column is 39.638062 The standard deviation of the selected column is 17.726544 The minimum of selected column is 11.781286 The maximum of selected column is 186.68805 The number of points used in calculation is 524-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<92.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.31E+05 125520 0001
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
121016 71581 0 49435 0 0
Writing events file
71581 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
121016 71581 0 49435 0 0
in 16923.09 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 71581
Total counts in chip images : 71580
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 27 65891
Flickering pixels iter, pixels & cnts : 1 17 422
Number of pixels rejected : 44
Number of (internal) image counts : 71580
Number of image cts rejected (N, %) : 66313 92.6417999
By chip : 0 1 2 3
Pixels rejected : 0 0 0 44
Image counts : 0 0 0 71580
Image cts rejected: 0 0 0 66313
Image cts rej (%) : 0.00 0.00 0.00 92.64
filtering data...
Total counts : 0 0 0 71581
Total cts rejected: 0 0 0 66314
Total cts rej (%) : 0.00 0.00 0.00 92.64
Number of clean counts accepted : 5267
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 44
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad82034000s100112h.evt use_events=no
Wrote cleaned events file to ad82034000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad82034000s100201m.unf because of modeThe sum of the selected column is 20817.775 The mean of the selected column is 43.370364 The standard deviation of the selected column is 18.491566 The minimum of selected column is 12.593788 The maximum of selected column is 169.12550 The number of points used in calculation is 480-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<98.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.45E+05 184530 0001
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
180005 78166 0 101839 0 0
Writing events file
78166 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
180005 78166 0 101839 0 0
in 15568.15 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 78166
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 29 72923
Flickering pixels iter, pixels & cnts : 1 19 540
Number of pixels rejected : 48
Number of (internal) image counts : 78166
Number of image cts rejected (N, %) : 73463 93.9833145
By chip : 0 1 2 3
Pixels rejected : 0 0 0 48
Image counts : 0 0 0 78166
Image cts rejected: 0 0 0 73463
Image cts rej (%) : 0.00 0.00 0.00 93.98
filtering data...
Total counts : 0 0 0 78166
Total cts rejected: 0 0 0 73463
Total cts rej (%) : 0.00 0.00 0.00 93.98
Number of clean counts accepted : 4703
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 48
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad82034000s100202m.evt use_events=no
Wrote cleaned events file to ad82034000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad82034000s100212m.unf into ad82034000s100212m.evtThe sum of the selected column is 20817.775 The mean of the selected column is 43.370364 The standard deviation of the selected column is 18.491566 The minimum of selected column is 12.593788 The maximum of selected column is 169.12550 The number of points used in calculation is 480-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<98.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.45E+05 184980 0001
Processing file: /data/data15/seq_proc/82034000.005/ad82034000s100212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
180205 78239 0 101966 0 0
Writing events file
78239 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
180205 78239 0 101966 0 0
in 15568.15 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/82034000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/82034000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 78239
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 29 72922
Flickering pixels iter, pixels & cnts : 1 19 540
Number of pixels rejected : 48
Number of (internal) image counts : 78239
Number of image cts rejected (N, %) : 73462 93.8943481
By chip : 0 1 2 3
Pixels rejected : 0 0 0 48
Image counts : 0 0 0 78239
Image cts rejected: 0 0 0 73462
Image cts rej (%) : 0.00 0.00 0.00 93.89
filtering data...
Total counts : 0 0 0 78239
Total cts rejected: 0 0 0 73462
Total cts rej (%) : 0.00 0.00 0.00 93.89
Number of clean counts accepted : 4777
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 48
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad82034000s100212m.evt use_events=no
Wrote cleaned events file to ad82034000s100212m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad82034000g200170m.unf into ad82034000g200170m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 39189 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.unf
Total Good Bad: Region Time Phase Cut
39189 9230 22956 7003 0 0
Writing events file
9230 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
39189 9230 22956 7003 0 0
in 18479.64 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
9230 8486 744
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad82034000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 8486 in ad82034000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:33 0.28E+05 29752 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.unf
Total Good Bad: Region Time Phase Cut
29752 8902 16138 4712 0 0
Writing events file
8902 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29752 8902 16138 4712 0 0
in 18397.03 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8902 8200 702
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad82034000g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 8200 in ad82034000g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 38058 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.unf
Total Good Bad: Region Time Phase Cut
38058 10038 20304 7716 0 0
Writing events file
10038 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
38058 10038 20304 7716 0 0
in 18479.44 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
10038 9172 866
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad82034000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 9172 in ad82034000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:35 0.28E+05 29378 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.unf
Total Good Bad: Region Time Phase Cut
29378 10007 14216 5155 0 0
Writing events file
10007 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29378 10007 14216 5155 0 0
in 18385.03 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
10007 9248 759
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!screen:ASCA > read events ad82034000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad82034000g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 9248 in ad82034000g300270h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad82034000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7463
Mean RA/DEC/ROLL : 14.0157 26.4714 305.7463
Pnt RA/DEC/ROLL : 14.0186 26.5350 305.7463
Image rebin factor : 1
Attitude Records : 75977
GTI intervals : 24
Total GTI (secs) : 18479.641
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3104.0034180 3104.0034180
20 Percent Complete: Total/live time: 4336.0112305 4336.0112305
30 Percent Complete: Total/live time: 6337.7343750 6337.7343750
40 Percent Complete: Total/live time: 8511.8837891 8511.8837891
50 Percent Complete: Total/live time: 9733.7177734 9733.7177734
60 Percent Complete: Total/live time: 12287.8828125 12287.8828125
70 Percent Complete: Total/live time: 13151.8818359 13151.8818359
80 Percent Complete: Total/live time: 15199.8818359 15199.8818359
90 Percent Complete: Total/live time: 17549.8710938 17549.8710938
100 Percent Complete: Total/live time: 18479.6386719 18479.6386719
Number of attitude steps used: 45
Number of attitude steps avail: 10482
Mean RA/DEC pixel offset: -11.2676 -3.2078
writing expo file: ad82034000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 8410 76 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8486 8410 76 0 0 0
in 18479.64 seconds
Image has 8410 counts for 0.4551 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 4073 76 0 0 4337
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8486 4073 76 0 0 4337
in 18479.64 seconds
Image has 4073 counts for 0.2204 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 4369 76 0 0 4041
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8486 4369 76 0 0 4041
in 18479.64 seconds
Image has 4369 counts for 0.2364 counts/sec
Command not found; type ? for a command listing
!ad82034000g200170m:ASCA >
!ad82034000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000g200170m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000g200170m:ASCA > read events ad82034000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000g200170m:ASCA-GIS2-PH > set image sky
!ad82034000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad82034000g200170m:ASCA-GIS2-PH > extract image
!ad82034000g200170m:ASCA-GIS2-PH > save image outfile=ad82034000g200170m.img
Wrote image to file ad82034000g200170m.img
!ad82034000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad82034000g200170m:ASCA-GIS2-PH > extract image
!ad82034000g200170m:ASCA-GIS2-PH > save image outfile=ad82034000g200170m_lo.img
Wrote image to file ad82034000g200170m_lo.img
!ad82034000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad82034000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad82034000g200170m:ASCA-GIS2-PH > extract image
!ad82034000g200170m:ASCA-GIS2-PH > save image outfile=ad82034000g200170m_hi.img
Wrote image to file ad82034000g200170m_hi.img
!ad82034000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad82034000g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad82034000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7462
Mean RA/DEC/ROLL : 14.0177 26.4728 305.7462
Pnt RA/DEC/ROLL : 13.9976 26.5204 305.7462
Image rebin factor : 1
Attitude Records : 75977
GTI intervals : 35
Total GTI (secs) : 18397.027
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2150.0461426 2150.0461426
20 Percent Complete: Total/live time: 3926.0527344 3926.0527344
30 Percent Complete: Total/live time: 5998.0581055 5998.0581055
40 Percent Complete: Total/live time: 8262.0634766 8262.0634766
50 Percent Complete: Total/live time: 9476.0605469 9476.0605469
60 Percent Complete: Total/live time: 11522.0556641 11522.0556641
70 Percent Complete: Total/live time: 13214.2714844 13214.2714844
80 Percent Complete: Total/live time: 14912.5048828 14912.5048828
90 Percent Complete: Total/live time: 16832.7578125 16832.7578125
100 Percent Complete: Total/live time: 18397.0273438 18397.0273438
Number of attitude steps used: 71
Number of attitude steps avail: 44479
Mean RA/DEC pixel offset: -11.3484 -2.6538
writing expo file: ad82034000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:33 0.18E+05 8200 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 8122 78 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8200 8122 78 0 0 0
in 18397.03 seconds
Image has 8122 counts for 0.4415 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 3893 78 0 0 4229
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8200 3893 78 0 0 4229
in 18397.03 seconds
Image has 3893 counts for 0.2116 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 4266 78 0 0 3856
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8200 4266 78 0 0 3856
in 18397.03 seconds
Image has 4266 counts for 0.2319 counts/sec
Command not found; type ? for a command listing
!ad82034000g200270h:ASCA >
!ad82034000g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000g200270h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000g200270h:ASCA > read events ad82034000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000g200270h:ASCA-GIS2-PH > set image sky
!ad82034000g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad82034000g200270h:ASCA-GIS2-PH > extract image
!ad82034000g200270h:ASCA-GIS2-PH > save image outfile=ad82034000g200270h.img
Wrote image to file ad82034000g200270h.img
!ad82034000g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad82034000g200270h:ASCA-GIS2-PH > extract image
!ad82034000g200270h:ASCA-GIS2-PH > save image outfile=ad82034000g200270h_lo.img
Wrote image to file ad82034000g200270h_lo.img
!ad82034000g200270h:ASCA-GIS2-PH > clear pha_cut
!ad82034000g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad82034000g200270h:ASCA-GIS2-PH > extract image
!ad82034000g200270h:ASCA-GIS2-PH > save image outfile=ad82034000g200270h_hi.img
Wrote image to file ad82034000g200270h_hi.img
!ad82034000g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad82034000g300170m.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad82034000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7402
Mean RA/DEC/ROLL : 14.0018 26.4928 305.7402
Pnt RA/DEC/ROLL : 14.0325 26.5135 305.7402
Image rebin factor : 1
Attitude Records : 75977
GTI intervals : 24
Total GTI (secs) : 18479.438
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3104.0034180 3104.0034180
20 Percent Complete: Total/live time: 4336.0112305 4336.0112305
30 Percent Complete: Total/live time: 6337.7343750 6337.7343750
40 Percent Complete: Total/live time: 8511.8837891 8511.8837891
50 Percent Complete: Total/live time: 9733.7177734 9733.7177734
60 Percent Complete: Total/live time: 12287.8828125 12287.8828125
70 Percent Complete: Total/live time: 13151.8818359 13151.8818359
80 Percent Complete: Total/live time: 15199.8818359 15199.8818359
90 Percent Complete: Total/live time: 17549.6679688 17549.6679688
100 Percent Complete: Total/live time: 18479.4355469 18479.4355469
Number of attitude steps used: 45
Number of attitude steps avail: 10482
Mean RA/DEC pixel offset: 0.5426 -2.0346
writing expo file: ad82034000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 9105 67 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9172 9105 67 0 0 0
in 18479.44 seconds
Image has 9105 counts for 0.4927 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 4420 67 0 0 4685
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9172 4420 67 0 0 4685
in 18479.44 seconds
Image has 4420 counts for 0.2392 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 4710 67 0 0 4395
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9172 4710 67 0 0 4395
in 18479.44 seconds
Image has 4710 counts for 0.2549 counts/sec
Command not found; type ? for a command listing
!ad82034000g300170m:ASCA >
!ad82034000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000g300170m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000g300170m:ASCA > read events ad82034000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000g300170m:ASCA-GIS3-PH > set image sky
!ad82034000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad82034000g300170m:ASCA-GIS3-PH > extract image
!ad82034000g300170m:ASCA-GIS3-PH > save image outfile=ad82034000g300170m.img
Wrote image to file ad82034000g300170m.img
!ad82034000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad82034000g300170m:ASCA-GIS3-PH > extract image
!ad82034000g300170m:ASCA-GIS3-PH > save image outfile=ad82034000g300170m_lo.img
Wrote image to file ad82034000g300170m_lo.img
!ad82034000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad82034000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad82034000g300170m:ASCA-GIS3-PH > extract image
!ad82034000g300170m:ASCA-GIS3-PH > save image outfile=ad82034000g300170m_hi.img
Wrote image to file ad82034000g300170m_hi.img
!ad82034000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad82034000g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad82034000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7401
Mean RA/DEC/ROLL : 14.0037 26.4943 305.7401
Pnt RA/DEC/ROLL : 14.0115 26.4989 305.7401
Image rebin factor : 1
Attitude Records : 75977
GTI intervals : 35
Total GTI (secs) : 18385.027
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2026.4934082 2026.4934082
20 Percent Complete: Total/live time: 3918.0522461 3918.0522461
30 Percent Complete: Total/live time: 5988.0581055 5988.0581055
40 Percent Complete: Total/live time: 8250.0634766 8250.0634766
50 Percent Complete: Total/live time: 9464.0605469 9464.0605469
60 Percent Complete: Total/live time: 11510.0556641 11510.0556641
70 Percent Complete: Total/live time: 13202.2714844 13202.2714844
80 Percent Complete: Total/live time: 14900.5048828 14900.5048828
90 Percent Complete: Total/live time: 16820.7578125 16820.7578125
100 Percent Complete: Total/live time: 18385.0273438 18385.0273438
Number of attitude steps used: 64
Number of attitude steps avail: 46723
Mean RA/DEC pixel offset: 0.5342 -1.6499
writing expo file: ad82034000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:35 0.18E+05 9248 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 9192 56 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9248 9192 56 0 0 0
in 18385.03 seconds
Image has 9192 counts for 0.5000 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 4467 56 0 0 4725
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9248 4467 56 0 0 4725
in 18385.03 seconds
Image has 4467 counts for 0.2430 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 4759 56 0 0 4433
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9248 4759 56 0 0 4433
in 18385.03 seconds
Image has 4759 counts for 0.2589 counts/sec
Command not found; type ? for a command listing
!ad82034000g300270h:ASCA >
!ad82034000g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000g300270h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000g300270h:ASCA > read events ad82034000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000g300270h:ASCA-GIS3-PH > set image sky
!ad82034000g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad82034000g300270h:ASCA-GIS3-PH > extract image
!ad82034000g300270h:ASCA-GIS3-PH > save image outfile=ad82034000g300270h.img
Wrote image to file ad82034000g300270h.img
!ad82034000g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad82034000g300270h:ASCA-GIS3-PH > extract image
!ad82034000g300270h:ASCA-GIS3-PH > save image outfile=ad82034000g300270h_lo.img
Wrote image to file ad82034000g300270h_lo.img
!ad82034000g300270h:ASCA-GIS3-PH > clear pha_cut
!ad82034000g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad82034000g300270h:ASCA-GIS3-PH > extract image
!ad82034000g300270h:ASCA-GIS3-PH > save image outfile=ad82034000g300270h_hi.img
Wrote image to file ad82034000g300270h_hi.img
!ad82034000g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad82034000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad82034000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7370
Mean RA/DEC/ROLL : 13.9965 26.4743 305.7370
Pnt RA/DEC/ROLL : 14.0181 26.5182 305.7370
Image rebin factor : 4
Attitude Records : 75977
Hot Pixels : 24
GTI intervals : 36
Total GTI (secs) : 16869.305
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2005.9194336 2005.9194336
20 Percent Complete: Total/live time: 3573.9194336 3573.9194336
30 Percent Complete: Total/live time: 5427.8925781 5427.8925781
40 Percent Complete: Total/live time: 7345.8652344 7345.8652344
50 Percent Complete: Total/live time: 9298.2666016 9298.2666016
60 Percent Complete: Total/live time: 10465.5566406 10465.5566406
70 Percent Complete: Total/live time: 12161.4941406 12161.4941406
80 Percent Complete: Total/live time: 13723.4628906 13723.4628906
90 Percent Complete: Total/live time: 15520.6289062 15520.6289062
100 Percent Complete: Total/live time: 16869.3066406 16869.3066406
Number of attitude steps used: 66
Number of attitude steps avail: 42502
Mean RA/DEC pixel offset: -49.6255 -89.9719
writing expo file: ad82034000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 6218 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6218 6218 0 0 0 0
in 16869.30 seconds
Image has 6218 counts for 0.3686 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 3975 0 0 0 2243
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6218 3975 0 0 0 2243
in 16869.30 seconds
Image has 3975 counts for 0.2356 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 2250 0 0 0 3968
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6218 2250 0 0 0 3968
in 16869.30 seconds
Image has 2250 counts for 0.1334 counts/sec
Command not found; type ? for a command listing
!ad82034000s000102h:ASCA >
!ad82034000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000s000102h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000s000102h:ASCA > read events ad82034000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad82034000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad82034000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000102h.img
Wrote image to file ad82034000s000102h.img
!ad82034000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad82034000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000102h_lo.img
Wrote image to file ad82034000s000102h_lo.img
!ad82034000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad82034000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad82034000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000102h_hi.img
Wrote image to file ad82034000s000102h_hi.img
!ad82034000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad82034000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad82034000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7371
Mean RA/DEC/ROLL : 13.9948 26.4731 305.7371
Pnt RA/DEC/ROLL : 14.0398 26.5329 305.7371
Image rebin factor : 4
Attitude Records : 75977
Hot Pixels : 32
GTI intervals : 30
Total GTI (secs) : 15664.147
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2101.7172852 2101.7172852
20 Percent Complete: Total/live time: 3476.7114258 3476.7114258
30 Percent Complete: Total/live time: 5130.4638672 5130.4638672
40 Percent Complete: Total/live time: 7288.6123047 7288.6123047
50 Percent Complete: Total/live time: 8062.4467773 8062.4467773
60 Percent Complete: Total/live time: 10136.6123047 10136.6123047
70 Percent Complete: Total/live time: 11898.4248047 11898.4248047
80 Percent Complete: Total/live time: 13240.6113281 13240.6113281
90 Percent Complete: Total/live time: 14808.6113281 14808.6113281
100 Percent Complete: Total/live time: 15664.1464844 15664.1464844
Number of attitude steps used: 49
Number of attitude steps avail: 23101
Mean RA/DEC pixel offset: -49.2998 -91.3464
writing expo file: ad82034000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 5666 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 5666 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5666 5666 0 0 0 0
in 15664.15 seconds
Image has 5666 counts for 0.3617 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 3653 0 0 0 2013
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5666 3653 0 0 0 2013
in 15664.15 seconds
Image has 3653 counts for 0.2332 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 2017 0 0 0 3649
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5666 2017 0 0 0 3649
in 15664.15 seconds
Image has 2017 counts for 0.1288 counts/sec
Command not found; type ? for a command listing
!ad82034000s000202m:ASCA >
!ad82034000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000s000202m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000s000202m:ASCA > read events ad82034000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad82034000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad82034000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000202m.img
Wrote image to file ad82034000s000202m.img
!ad82034000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad82034000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000202m_lo.img
Wrote image to file ad82034000s000202m_lo.img
!ad82034000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad82034000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad82034000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad82034000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad82034000s000202m_hi.img
Wrote image to file ad82034000s000202m_hi.img
!ad82034000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad82034000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad82034000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 89 6 206
AREA DISC H STOP: 425 425 342 282
AREA DISC V START: 2 123 123 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7437
Mean RA/DEC/ROLL : 14.0117 26.4829 305.7437
Pnt RA/DEC/ROLL : 14.0031 26.5097 305.7437
Image rebin factor : 4
Attitude Records : 75977
Hot Pixels : 44
GTI intervals : 33
Total GTI (secs) : 16923.090
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2005.9194336 2005.9194336
20 Percent Complete: Total/live time: 3573.9194336 3573.9194336
30 Percent Complete: Total/live time: 5427.8925781 5427.8925781
40 Percent Complete: Total/live time: 7281.8652344 7281.8652344
50 Percent Complete: Total/live time: 9290.2666016 9290.2666016
60 Percent Complete: Total/live time: 10457.5566406 10457.5566406
70 Percent Complete: Total/live time: 12147.2783203 12147.2783203
80 Percent Complete: Total/live time: 13745.2470703 13745.2470703
90 Percent Complete: Total/live time: 15542.4130859 15542.4130859
100 Percent Complete: Total/live time: 16923.0898438 16923.0898438
Number of attitude steps used: 67
Number of attitude steps avail: 42695
Mean RA/DEC pixel offset: -54.0291 -19.3260
writing expo file: ad82034000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 5181 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5181 5181 0 0 0 0
in 16923.09 seconds
Image has 5181 counts for 0.3061 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 3234 0 0 0 1947
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5181 3234 0 0 0 1947
in 16923.09 seconds
Image has 3234 counts for 0.1911 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 1954 0 0 0 3227
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5181 1954 0 0 0 3227
in 16923.09 seconds
Image has 1954 counts for 0.1155 counts/sec
Command not found; type ? for a command listing
!ad82034000s100102h:ASCA >
!ad82034000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000s100102h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000s100102h:ASCA > read events ad82034000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad82034000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad82034000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100102h.img
Wrote image to file ad82034000s100102h.img
!ad82034000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad82034000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100102h_lo.img
Wrote image to file ad82034000s100102h_lo.img
!ad82034000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad82034000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad82034000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100102h_hi.img
Wrote image to file ad82034000s100102h_hi.img
!ad82034000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad82034000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad82034000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 89 6 206
AREA DISC H STOP: 425 425 342 282
AREA DISC V START: 2 123 123 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940805_2305.0035
making an exposure map...
Aspect RA/DEC/ROLL : 14.0071 26.4956 305.7437
Mean RA/DEC/ROLL : 14.0099 26.4816 305.7437
Pnt RA/DEC/ROLL : 14.0247 26.5244 305.7437
Image rebin factor : 4
Attitude Records : 75977
Hot Pixels : 48
GTI intervals : 31
Total GTI (secs) : 15568.147
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2069.7172852 2069.7172852
20 Percent Complete: Total/live time: 3444.7114258 3444.7114258
30 Percent Complete: Total/live time: 5066.4638672 5066.4638672
40 Percent Complete: Total/live time: 7128.6123047 7128.6123047
50 Percent Complete: Total/live time: 9976.6123047 9976.6123047
60 Percent Complete: Total/live time: 9976.6123047 9976.6123047
70 Percent Complete: Total/live time: 11738.4248047 11738.4248047
80 Percent Complete: Total/live time: 13144.6113281 13144.6113281
90 Percent Complete: Total/live time: 14712.6113281 14712.6113281
100 Percent Complete: Total/live time: 15568.1464844 15568.1464844
Number of attitude steps used: 49
Number of attitude steps avail: 23093
Mean RA/DEC pixel offset: -53.6534 -20.9617
writing expo file: ad82034000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad82034000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad82034000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 4703 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 4703 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4703 4703 0 0 0 0
in 15568.15 seconds
Image has 4703 counts for 0.3021 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 2953 0 0 0 1750
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4703 2953 0 0 0 1750
in 15568.15 seconds
Image has 2953 counts for 0.1897 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 1757 0 0 0 2946
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4703 1757 0 0 0 2946
in 15568.15 seconds
Image has 1757 counts for 0.1129 counts/sec
Command not found; type ? for a command listing
!ad82034000s100202m:ASCA >
!ad82034000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad82034000s100202m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!ad82034000s100202m:ASCA > read events ad82034000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!ad82034000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad82034000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad82034000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100202m.img
Wrote image to file ad82034000s100202m.img
!ad82034000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad82034000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100202m_lo.img
Wrote image to file ad82034000s100202m_lo.img
!ad82034000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad82034000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad82034000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad82034000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad82034000s100202m_hi.img
Wrote image to file ad82034000s100202m_hi.img
!ad82034000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad82034000s000102h.expo ad82034000s000202m.expo ad82034000s100102h.expo ad82034000s100202m.expo-> Summing the following images to produce ad82034000sis32002_all.totsky
ad82034000s000102h.img ad82034000s000202m.img ad82034000s100102h.img ad82034000s100202m.img-> Summing the following images to produce ad82034000sis32002_lo.totsky
ad82034000s000102h_lo.img ad82034000s000202m_lo.img ad82034000s100102h_lo.img ad82034000s100202m_lo.img-> Summing the following images to produce ad82034000sis32002_hi.totsky
ad82034000s000102h_hi.img ad82034000s000202m_hi.img ad82034000s100102h_hi.img ad82034000s100202m_hi.img-> Running XIMAGE to create ad82034000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad82034000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 23.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 23 min: 0 ![2]XIMAGE> read/exp_map ad82034000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 1083.74 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1083 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 56 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 13.0000 13 0 ![9]XIMAGE> exit-> Summing gis images
ad82034000g200170m.expo ad82034000g200270h.expo ad82034000g300170m.expo ad82034000g300270h.expo-> Summing the following images to produce ad82034000gis25670_all.totsky
ad82034000g200170m.img ad82034000g200270h.img ad82034000g300170m.img ad82034000g300270h.img-> Summing the following images to produce ad82034000gis25670_lo.totsky
ad82034000g200170m_lo.img ad82034000g200270h_lo.img ad82034000g300170m_lo.img ad82034000g300270h_lo.img-> Summing the following images to produce ad82034000gis25670_hi.totsky
ad82034000g200170m_hi.img ad82034000g200270h_hi.img ad82034000g300170m_hi.img ad82034000g300270h_hi.img-> Running XIMAGE to create ad82034000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad82034000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 45.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 45 min: 0 ![2]XIMAGE> read/exp_map ad82034000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1229.02 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1229 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 3781 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 14.0000 14 0 ![9]XIMAGE> exit
135 110 0.000409842 112 15 41.628-> Smoothing ad82034000gis25670_hi.totsky with ad82034000gis25670.totexpo
135 110 0.000200401 112 16 35.39-> Smoothing ad82034000gis25670_lo.totsky with ad82034000gis25670.totexpo
134 109 0.000210948 113 16 48.0163-> Determining extraction radii
135 110 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad82034000gis25670.src
175 113 0.000203524 94 24 40.8711-> Smoothing ad82034000sis32002_hi.totsky with ad82034000sis32002.totexpo
175 115 6.03505e-05 96 32 23.4335-> Smoothing ad82034000sis32002_lo.totsky with ad82034000sis32002.totexpo
175 113 0.000152215 94 21 53.4905-> Determining extraction radii
175 113 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad82034000sis32002.src
The sum of the selected column is 1988.0000 The mean of the selected column is 497.00000 The standard deviation of the selected column is 2.4494897 The minimum of selected column is 494.00000 The maximum of selected column is 500.00000 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1744.0000 The mean of the selected column is 436.00000 The standard deviation of the selected column is 4.0824829 The minimum of selected column is 433.00000 The maximum of selected column is 442.00000 The number of points used in calculation is 4-> Converting (700.0,452.0,2.0) to s1 detector coordinates
The sum of the selected column is 1977.0000 The mean of the selected column is 494.25000 The standard deviation of the selected column is 3.2015621 The minimum of selected column is 491.00000 The maximum of selected column is 497.00000 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1881.0000 The mean of the selected column is 470.25000 The standard deviation of the selected column is 0.95742711 The minimum of selected column is 469.00000 The maximum of selected column is 471.00000 The number of points used in calculation is 4-> Converting (135.0,110.0,2.0) to g2 detector coordinates
The sum of the selected column is 20683.000 The mean of the selected column is 111.19892 The standard deviation of the selected column is 1.1846765 The minimum of selected column is 109.00000 The maximum of selected column is 114.00000 The number of points used in calculation is 186-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 20720.000 The mean of the selected column is 111.39785 The standard deviation of the selected column is 1.1497571 The minimum of selected column is 109.00000 The maximum of selected column is 114.00000 The number of points used in calculation is 186-> Converting (135.0,110.0,2.0) to g3 detector coordinates
The sum of the selected column is 27178.000 The mean of the selected column is 117.14655 The standard deviation of the selected column is 1.0911237 The minimum of selected column is 115.00000 The maximum of selected column is 120.00000 The number of points used in calculation is 232-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 25984.000 The mean of the selected column is 112.00000 The standard deviation of the selected column is 1.1696005 The minimum of selected column is 110.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 232
1 ad82034000s000102h.evt 11884 1 ad82034000s000202m.evt 11884-> Fetching SIS0_NOTCHIP0.1
ad82034000s000102h.evt ad82034000s000202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
2 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 5666 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 3909 2309 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 3642 2024 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11884 7551 4333 0 0 0
in 32533.45 seconds
Spectrum has 7551 counts for 0.2321 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32533. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.48340E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad82034000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad82034000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad82034000s010102_1.pi group=yes
Wrote spectrum to ad82034000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad82034000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32533. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.48340E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 15 are grouped by a factor 3 ... 16 - 21 are grouped by a factor 2 ... 22 - 75 are single channels ... 76 - 77 are grouped by a factor 2 ... 78 - 78 are single channels ... 79 - 110 are grouped by a factor 2 ... 111 - 116 are grouped by a factor 3 ... 117 - 118 are grouped by a factor 2 ... 119 - 121 are grouped by a factor 3 ... 122 - 129 are grouped by a factor 4 ... 130 - 131 are grouped by a factor 2 ... 132 - 143 are grouped by a factor 3 ... 144 - 167 are grouped by a factor 4 ... 168 - 172 are grouped by a factor 5 ... 173 - 186 are grouped by a factor 7 ... 187 - 198 are grouped by a factor 6 ... 199 - 210 are grouped by a factor 12 ... 211 - 223 are grouped by a factor 13 ... 224 - 250 are grouped by a factor 27 ... 251 - 285 are grouped by a factor 35 ... 286 - 349 are grouped by a factor 64 ... 350 - 475 are grouped by a factor 126 ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad82034000s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 38 by 39 bins
expanded to 38 by 39 bins
First WMAP bin is at detector pixel 344 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 51.662 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.50100E+03
Weighted mean angle from optical axis = 5.586 arcmin
-> Standard Output From STOOL group_event_files:1 ad82034000s000112h.evt 12082 1 ad82034000s000212m.evt 12082-> SIS0_NOTCHIP0.1 already present in current directory
ad82034000s000112h.evt ad82034000s000212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 6314 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 6314 0100
2 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.16E+05 5768 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000112h.evt
Total Good Bad: Region Time Phase Cut
6314 3960 2354 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000212m.evt
Total Good Bad: Region Time Phase Cut
5768 3693 2075 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12082 7653 4429 0 0 0
in 32533.45 seconds
Spectrum has 7653 counts for 0.2352 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32533. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.48340E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000s010212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad82034000s000212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad82034000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad82034000s010212_1.pi group=yes
Wrote spectrum to ad82034000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad82034000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32533. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.48340E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 30 are grouped by a factor 5 ... 31 - 42 are grouped by a factor 3 ... 43 - 52 are grouped by a factor 2 ... 53 - 54 are single channels ... 55 - 56 are grouped by a factor 2 ... 57 - 109 are single channels ... 110 - 111 are grouped by a factor 2 ... 112 - 114 are single channels ... 115 - 116 are grouped by a factor 2 ... 117 - 117 are single channels ... 118 - 123 are grouped by a factor 2 ... 124 - 124 are single channels ... 125 - 150 are grouped by a factor 2 ... 151 - 165 are grouped by a factor 3 ... 166 - 173 are grouped by a factor 4 ... 174 - 179 are grouped by a factor 3 ... 180 - 183 are grouped by a factor 4 ... 184 - 186 are grouped by a factor 3 ... 187 - 206 are grouped by a factor 4 ... 207 - 209 are grouped by a factor 3 ... 210 - 221 are grouped by a factor 4 ... 222 - 226 are grouped by a factor 5 ... 227 - 230 are grouped by a factor 4 ... 231 - 235 are grouped by a factor 5 ... 236 - 239 are grouped by a factor 4 ... 240 - 253 are grouped by a factor 7 ... 254 - 261 are grouped by a factor 8 ... 262 - 265 are grouped by a factor 4 ... 266 - 270 are grouped by a factor 5 ... 271 - 276 are grouped by a factor 6 ... 277 - 281 are grouped by a factor 5 ... 282 - 287 are grouped by a factor 6 ... 288 - 301 are grouped by a factor 7 ... 302 - 309 are grouped by a factor 8 ... 310 - 316 are grouped by a factor 7 ... 317 - 332 are grouped by a factor 8 ... 333 - 352 are grouped by a factor 10 ... 353 - 365 are grouped by a factor 13 ... 366 - 375 are grouped by a factor 10 ... 376 - 386 are grouped by a factor 11 ... 387 - 399 are grouped by a factor 13 ... 400 - 427 are grouped by a factor 28 ... 428 - 452 are grouped by a factor 25 ... 453 - 510 are grouped by a factor 58 ... 511 - 573 are grouped by a factor 63 ... 574 - 678 are grouped by a factor 105 ... 679 - 839 are grouped by a factor 161 ... 840 - 953 are grouped by a factor 114 ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad82034000s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 38 by 39 bins
expanded to 38 by 39 bins
First WMAP bin is at detector pixel 344 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 51.662 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.60300E+03
Weighted mean angle from optical axis = 5.590 arcmin
-> Standard Output From STOOL group_event_files:1 ad82034000s100102h.evt 9884 1 ad82034000s100202m.evt 9884-> Fetching SIS1_NOTCHIP0.1
ad82034000s100102h.evt ad82034000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
2 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 4703 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 3323 1858 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 2954 1749 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9884 6277 3607 0 0 0
in 32491.24 seconds
Spectrum has 6277 counts for 0.1932 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32491. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.52734E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad82034000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad82034000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad82034000s110102_1.pi group=yes
Wrote spectrum to ad82034000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad82034000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32491. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.52734E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 16 are grouped by a factor 4 ... 17 - 22 are grouped by a factor 2 ... 23 - 65 are single channels ... 66 - 67 are grouped by a factor 2 ... 68 - 71 are single channels ... 72 - 83 are grouped by a factor 2 ... 84 - 86 are grouped by a factor 3 ... 87 - 92 are grouped by a factor 2 ... 93 - 95 are grouped by a factor 3 ... 96 - 101 are grouped by a factor 2 ... 102 - 119 are grouped by a factor 3 ... 120 - 123 are grouped by a factor 4 ... 124 - 129 are grouped by a factor 3 ... 130 - 141 are grouped by a factor 4 ... 142 - 151 are grouped by a factor 5 ... 152 - 157 are grouped by a factor 6 ... 158 - 164 are grouped by a factor 7 ... 165 - 169 are grouped by a factor 5 ... 170 - 175 are grouped by a factor 6 ... 176 - 183 are grouped by a factor 8 ... 184 - 189 are grouped by a factor 6 ... 190 - 198 are grouped by a factor 9 ... 199 - 211 are grouped by a factor 13 ... 212 - 226 are grouped by a factor 15 ... 227 - 254 are grouped by a factor 28 ... 255 - 284 are grouped by a factor 30 ... 285 - 383 are grouped by a factor 99 ... 384 - 444 are grouped by a factor 61 ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad82034000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 38 by 39 bins
expanded to 38 by 39 bins
First WMAP bin is at detector pixel 344 320
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.169 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.23400E+03
Weighted mean angle from optical axis = 8.361 arcmin
-> Standard Output From STOOL group_event_files:1 ad82034000s100112h.evt 10044 1 ad82034000s100212m.evt 10044-> SIS1_NOTCHIP0.1 already present in current directory
ad82034000s100112h.evt ad82034000s100212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 5267 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 5267 0001
2 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.16E+05 4777 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100112h.evt
Total Good Bad: Region Time Phase Cut
5267 3367 1900 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100212m.evt
Total Good Bad: Region Time Phase Cut
4777 2990 1787 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10044 6357 3687 0 0 0
in 32491.24 seconds
Spectrum has 6357 counts for 0.1957 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 32491. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.52734E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000s110212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad82034000s100212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad82034000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad82034000s110212_1.pi group=yes
Wrote spectrum to ad82034000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad82034000s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 32491. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.52734E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 32 are grouped by a factor 7 ... 33 - 35 are grouped by a factor 3 ... 36 - 39 are grouped by a factor 4 ... 40 - 45 are grouped by a factor 3 ... 46 - 53 are grouped by a factor 2 ... 54 - 56 are single channels ... 57 - 58 are grouped by a factor 2 ... 59 - 59 are single channels ... 60 - 61 are grouped by a factor 2 ... 62 - 95 are single channels ... 96 - 97 are grouped by a factor 2 ... 98 - 102 are single channels ... 103 - 106 are grouped by a factor 2 ... 107 - 108 are single channels ... 109 - 130 are grouped by a factor 2 ... 131 - 133 are grouped by a factor 3 ... 134 - 143 are grouped by a factor 2 ... 144 - 152 are grouped by a factor 3 ... 153 - 156 are grouped by a factor 4 ... 157 - 165 are grouped by a factor 3 ... 166 - 170 are grouped by a factor 5 ... 171 - 178 are grouped by a factor 4 ... 179 - 181 are grouped by a factor 3 ... 182 - 201 are grouped by a factor 4 ... 202 - 206 are grouped by a factor 5 ... 207 - 210 are grouped by a factor 4 ... 211 - 230 are grouped by a factor 5 ... 231 - 237 are grouped by a factor 7 ... 238 - 261 are grouped by a factor 6 ... 262 - 268 are grouped by a factor 7 ... 269 - 274 are grouped by a factor 6 ... 275 - 288 are grouped by a factor 7 ... 289 - 298 are grouped by a factor 10 ... 299 - 310 are grouped by a factor 12 ... 311 - 332 are grouped by a factor 11 ... 333 - 341 are grouped by a factor 9 ... 342 - 352 are grouped by a factor 11 ... 353 - 368 are grouped by a factor 16 ... 369 - 379 are grouped by a factor 11 ... 380 - 396 are grouped by a factor 17 ... 397 - 422 are grouped by a factor 26 ... 423 - 451 are grouped by a factor 29 ... 452 - 504 are grouped by a factor 53 ... 505 - 553 are grouped by a factor 49 ... 554 - 664 are grouped by a factor 111 ... 665 - 857 are grouped by a factor 193 ... 858 - 878 are grouped by a factor 21 ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad82034000s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 38 by 39 bins
expanded to 38 by 39 bins
First WMAP bin is at detector pixel 344 320
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.169 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.31300E+03
Weighted mean angle from optical axis = 8.365 arcmin
-> Standard Output From STOOL group_event_files:1 ad82034000g200170m.evt 16686 1 ad82034000g200270h.evt 16686-> GIS2_REGION256.4 already present in current directory
ad82034000g200170m.evt ad82034000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
2 ABELL115 PH HIGH 06/08/94 00:11:33 0.18E+05 8200 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 3061 5425 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 2974 5226 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16686 6035 10651 0 0 0
in 36876.66 seconds
Spectrum has 6035 counts for 0.1637 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36877. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > read events ad82034000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad82034000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad82034000g210170_1.pi group=yes
Wrote spectrum to ad82034000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad82034000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad82034000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36877. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 35 are grouped by a factor 36 ... 36 - 45 are grouped by a factor 10 ... 46 - 53 are grouped by a factor 8 ... 54 - 60 are grouped by a factor 7 ... 61 - 64 are grouped by a factor 4 ... 65 - 79 are grouped by a factor 3 ... 80 - 83 are grouped by a factor 2 ... 84 - 86 are grouped by a factor 3 ... 87 - 90 are grouped by a factor 2 ... 91 - 93 are grouped by a factor 3 ... 94 - 125 are grouped by a factor 2 ... 126 - 126 are single channels ... 127 - 164 are grouped by a factor 2 ... 165 - 167 are grouped by a factor 3 ... 168 - 173 are grouped by a factor 2 ... 174 - 174 are single channels ... 175 - 180 are grouped by a factor 2 ... 181 - 183 are grouped by a factor 3 ... 184 - 185 are grouped by a factor 2 ... 186 - 188 are grouped by a factor 3 ... 189 - 190 are grouped by a factor 2 ... 191 - 193 are grouped by a factor 3 ... 194 - 195 are grouped by a factor 2 ... 196 - 210 are grouped by a factor 3 ... 211 - 214 are grouped by a factor 4 ... 215 - 220 are grouped by a factor 3 ... 221 - 230 are grouped by a factor 5 ... 231 - 246 are grouped by a factor 4 ... 247 - 251 are grouped by a factor 5 ... 252 - 255 are grouped by a factor 4 ... 256 - 275 are grouped by a factor 5 ... 276 - 281 are grouped by a factor 6 ... 282 - 286 are grouped by a factor 5 ... 287 - 290 are grouped by a factor 4 ... 291 - 305 are grouped by a factor 5 ... 306 - 323 are grouped by a factor 6 ... 324 - 337 are grouped by a factor 7 ... 338 - 346 are grouped by a factor 9 ... 347 - 370 are grouped by a factor 8 ... 371 - 380 are grouped by a factor 10 ... 381 - 391 are grouped by a factor 11 ... 392 - 411 are grouped by a factor 10 ... 412 - 427 are grouped by a factor 16 ... 428 - 436 are grouped by a factor 9 ... 437 - 449 are grouped by a factor 13 ... 450 - 463 are grouped by a factor 14 ... 464 - 474 are grouped by a factor 11 ... 475 - 487 are grouped by a factor 13 ... 488 - 503 are grouped by a factor 16 ... 504 - 520 are grouped by a factor 17 ... 521 - 543 are grouped by a factor 23 ... 544 - 568 are grouped by a factor 25 ... 569 - 603 are grouped by a factor 35 ... 604 - 657 are grouped by a factor 54 ... 658 - 695 are grouped by a factor 38 ... 696 - 772 are grouped by a factor 77 ... 773 - 938 are grouped by a factor 166 ... 939 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 49 49
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.03500E+03
Weighted mean angle from optical axis = 8.088 arcmin
-> Standard Output From STOOL group_event_files:1 ad82034000g300170m.evt 18420 1 ad82034000g300270h.evt 18420-> GIS3_REGION256.4 already present in current directory
ad82034000g300170m.evt ad82034000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
2 ABELL115 PH HIGH 06/08/94 00:11:35 0.18E+05 9248 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 3624 5548 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 3694 5554 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18420 7318 11102 0 0 0
in 36864.46 seconds
Spectrum has 7318 counts for 0.1985 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36864. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > read events ad82034000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad82034000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad82034000g310170_1.pi group=yes
Wrote spectrum to ad82034000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad82034000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad82034000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36864. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 30 are grouped by a factor 31 ... 31 - 40 are grouped by a factor 10 ... 41 - 49 are grouped by a factor 9 ... 50 - 55 are grouped by a factor 6 ... 56 - 65 are grouped by a factor 5 ... 66 - 69 are grouped by a factor 4 ... 70 - 72 are grouped by a factor 3 ... 73 - 92 are grouped by a factor 2 ... 93 - 93 are single channels ... 94 - 95 are grouped by a factor 2 ... 96 - 97 are single channels ... 98 - 101 are grouped by a factor 2 ... 102 - 102 are single channels ... 103 - 104 are grouped by a factor 2 ... 105 - 105 are single channels ... 106 - 109 are grouped by a factor 2 ... 110 - 111 are single channels ... 112 - 117 are grouped by a factor 2 ... 118 - 118 are single channels ... 119 - 120 are grouped by a factor 2 ... 121 - 122 are single channels ... 123 - 128 are grouped by a factor 2 ... 129 - 133 are single channels ... 134 - 139 are grouped by a factor 2 ... 140 - 140 are single channels ... 141 - 148 are grouped by a factor 2 ... 149 - 149 are single channels ... 150 - 195 are grouped by a factor 2 ... 196 - 204 are grouped by a factor 3 ... 205 - 206 are grouped by a factor 2 ... 207 - 212 are grouped by a factor 3 ... 213 - 220 are grouped by a factor 4 ... 221 - 226 are grouped by a factor 3 ... 227 - 238 are grouped by a factor 4 ... 239 - 241 are grouped by a factor 3 ... 242 - 256 are grouped by a factor 5 ... 257 - 260 are grouped by a factor 4 ... 261 - 263 are grouped by a factor 3 ... 264 - 267 are grouped by a factor 4 ... 268 - 270 are grouped by a factor 3 ... 271 - 278 are grouped by a factor 4 ... 279 - 293 are grouped by a factor 5 ... 294 - 297 are grouped by a factor 4 ... 298 - 303 are grouped by a factor 6 ... 304 - 318 are grouped by a factor 5 ... 319 - 324 are grouped by a factor 6 ... 325 - 329 are grouped by a factor 5 ... 330 - 341 are grouped by a factor 6 ... 342 - 346 are grouped by a factor 5 ... 347 - 352 are grouped by a factor 6 ... 353 - 366 are grouped by a factor 7 ... 367 - 382 are grouped by a factor 8 ... 383 - 389 are grouped by a factor 7 ... 390 - 394 are grouped by a factor 5 ... 395 - 402 are grouped by a factor 8 ... 403 - 408 are grouped by a factor 6 ... 409 - 428 are grouped by a factor 10 ... 429 - 435 are grouped by a factor 7 ... 436 - 465 are grouped by a factor 10 ... 466 - 473 are grouped by a factor 8 ... 474 - 484 are grouped by a factor 11 ... 485 - 496 are grouped by a factor 12 ... 497 - 510 are grouped by a factor 14 ... 511 - 540 are grouped by a factor 15 ... 541 - 554 are grouped by a factor 14 ... 555 - 585 are grouped by a factor 31 ... 586 - 651 are grouped by a factor 33 ... 652 - 691 are grouped by a factor 40 ... 692 - 752 are grouped by a factor 61 ... 753 - 876 are grouped by a factor 124 ... 877 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad82034000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 55 50
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.31800E+03
Weighted mean angle from optical axis = 6.143 arcmin
-> Plotting ad82034000g210170_1_pi.ps from ad82034000g210170_1.pi
XSPEC 9.01 09:44:09 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000g210170_1.pi
Net count rate (cts/s) for file 1 0.1637 +/- 2.1200E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad82034000g310170_1_pi.ps from ad82034000g310170_1.pi
XSPEC 9.01 09:44:28 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000g310170_1.pi
Net count rate (cts/s) for file 1 0.1985 +/- 2.3389E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad82034000s010102_1_pi.ps from ad82034000s010102_1.pi
XSPEC 9.01 09:44:45 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000s010102_1.pi
Net count rate (cts/s) for file 1 0.2321 +/- 2.6731E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad82034000s010212_1_pi.ps from ad82034000s010212_1.pi
XSPEC 9.01 09:45:02 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000s010212_1.pi
Net count rate (cts/s) for file 1 0.2352 +/- 2.6934E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad82034000s110102_1_pi.ps from ad82034000s110102_1.pi
XSPEC 9.01 09:45:21 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000s110102_1.pi
Net count rate (cts/s) for file 1 0.1932 +/- 2.4406E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad82034000s110212_1_pi.ps from ad82034000s110212_1.pi
XSPEC 9.01 09:45:40 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad82034000s110212_1.pi
Net count rate (cts/s) for file 1 0.1957 +/- 2.4582E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
2 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 5666 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 3912 2306 0 0 0
Writing events file
3912 events written to the output file
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 3650 2016 0 0 0
Writing events file
7562 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11884 7562 4322 0 0 0
in 32533.45 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad82034000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad82034000s000002_1.lc with binsize 215.111425910584
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 05/08/94 23:05:21 0.33E+05 7562 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/events.tmp
Total Good Bad: Region Time Phase Cut
7562 7562 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7562 7562 0 0 0 0
in 32533.45 seconds
Fits light curve has 7562 counts for 0.2324 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > set binsize 215.111425910584
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad82034000s000002_1.lc
Wrote FITS light curve to file ad82034000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad82034000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad82034000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ ABELL115 Start Time (d) .... 9570 00:12:07.436
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9571 00:35:35.436
No. of Rows ....... 154 Bin Time (s) ...... 215.1
Right Ascension ... 1.4007E+01 Internal time sys.. Converted to TJD
Declination ....... 2.6496E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 409 Newbins of 215.111 (s)
Intv 1 Start 9570 0:13:54
Ser.1 Avg 0.2332 Chisq 154.7 Var 0.1193E-02 Newbs. 154
Min 0.1581 Max 0.3307 expVar 0.1188E-02 Bins 154
Results from Statistical Analysis
Newbin Integration Time (s).. 215.11
Interval Duration (s)........ 87550.
No. of Newbins .............. 154
Average (c/s) ............... 0.23316 +/- 0.28E-02
Standard Deviation (c/s)..... 0.34544E-01
Minimum (c/s)................ 0.15806
Maximum (c/s)................ 0.33071
Variance ((c/s)**2).......... 0.11933E-02 +/- 0.14E-03
Expected Variance ((c/s)**2). 0.11877E-02 +/- 0.14E-03
Third Moment ((c/s)**3)...... 0.22023E-04
Average Deviation (c/s)...... 0.27216E-01
Skewness..................... 0.53428 +/- 0.20
Kurtosis..................... 0.16990 +/- 0.39
RMS fractional variation....< 0.90336E-01 (3 sigma)
Chi-Square................... 154.73 dof 153
Chi-Square Prob of constancy. 0.44573 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.18965 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 409 Newbins of 215.111 (s)
Intv 1 Start 9570 0:13:54
Ser.1 Avg 0.2332 Chisq 154.7 Var 0.1193E-02 Newbs. 154
Min 0.1581 Max 0.3307 expVar 0.1188E-02 Bins 154
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad82034000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
2 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 4703 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 3325 1856 0 0 0
Writing events file
3325 events written to the output file
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 2955 1748 0 0 0
Writing events file
6280 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9884 6280 3604 0 0 0
in 32491.24 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad82034000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad82034000s100002_1.lc with binsize 258.688187752702
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 05/08/94 23:05:21 0.32E+05 6280 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6280 6280 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6280 6280 0 0 0 0
in 32491.24 seconds
Fits light curve has 6280 counts for 0.1933 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 258.688187752702
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad82034000s100002_1.lc
Wrote FITS light curve to file ad82034000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad82034000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad82034000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ ABELL115 Start Time (d) .... 9570 00:12:07.436
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9571 00:35:35.436
No. of Rows ....... 126 Bin Time (s) ...... 258.7
Right Ascension ... 1.4007E+01 Internal time sys.. Converted to TJD
Declination ....... 2.6496E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 340 Newbins of 258.688 (s)
Intv 1 Start 9570 0:14:16
Ser.1 Avg 0.1932 Chisq 123.8 Var 0.8007E-03 Newbs. 126
Min 0.1276 Max 0.2766 expVar 0.8152E-03 Bins 126
Results from Statistical Analysis
Newbin Integration Time (s).. 258.69
Interval Duration (s)........ 87437.
No. of Newbins .............. 126
Average (c/s) ............... 0.19318 +/- 0.26E-02
Standard Deviation (c/s)..... 0.28296E-01
Minimum (c/s)................ 0.12757
Maximum (c/s)................ 0.27657
Variance ((c/s)**2).......... 0.80068E-03 +/- 0.10E-03
Expected Variance ((c/s)**2). 0.81516E-03 +/- 0.10E-03
Third Moment ((c/s)**3)...... 0.46113E-05
Average Deviation (c/s)...... 0.22731E-01
Skewness..................... 0.20353 +/- 0.22
Kurtosis..................... 0.25065E-01 +/- 0.44
RMS fractional variation....< 0.98013E-01 (3 sigma)
Chi-Square................... 123.76 dof 125
Chi-Square Prob of constancy. 0.51443 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.28920 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 340 Newbins of 258.688 (s)
Intv 1 Start 9570 0:14:16
Ser.1 Avg 0.1932 Chisq 123.8 Var 0.8007E-03 Newbs. 126
Min 0.1276 Max 0.2766 expVar 0.8152E-03 Bins 126
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad82034000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
2 ABELL115 PH HIGH 06/08/94 00:11:33 0.18E+05 8200 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 3061 5425 0 0 0
Writing events file
3061 events written to the output file
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 2974 5226 0 0 0
Writing events file
6035 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16686 6035 10651 0 0 0
in 36876.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > read events ad82034000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > filter region ad82034000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad82034000g200070_1.lc with binsize 305.523309335421
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.37E+05 6035 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6035 6035 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6035 6035 0 0 0 0
in 36876.66 seconds
Fits light curve has 6035 counts for 0.1637 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > set binsize 305.523309335421
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad82034000g200070_1.lc
Wrote FITS light curve to file ad82034000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad82034000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad82034000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ ABELL115 Start Time (d) .... 9570 00:11:33.424
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9571 00:35:35.436
No. of Rows ....... 122 Bin Time (s) ...... 305.5
Right Ascension ... 1.4007E+01 Internal time sys.. Converted to TJD
Declination ....... 2.6496E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 288 Newbins of 305.523 (s)
Intv 1 Start 9570 0:14: 6
Ser.1 Avg 0.1644 Chisq 114.6 Var 0.5592E-03 Newbs. 122
Min 0.9819E-01 Max 0.2403 expVar 0.5952E-03 Bins 122
Results from Statistical Analysis
Newbin Integration Time (s).. 305.52
Interval Duration (s)........ 87685.
No. of Newbins .............. 122
Average (c/s) ............... 0.16442 +/- 0.22E-02
Standard Deviation (c/s)..... 0.23648E-01
Minimum (c/s)................ 0.98192E-01
Maximum (c/s)................ 0.24028
Variance ((c/s)**2).......... 0.55923E-03 +/- 0.72E-04
Expected Variance ((c/s)**2). 0.59517E-03 +/- 0.77E-04
Third Moment ((c/s)**3)...... 0.25969E-05
Average Deviation (c/s)...... 0.19281E-01
Skewness..................... 0.19637 +/- 0.22
Kurtosis..................... 0.66336E-01 +/- 0.44
RMS fractional variation....< 0.10393 (3 sigma)
Chi-Square................... 114.63 dof 121
Chi-Square Prob of constancy. 0.64567 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.23717E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 288 Newbins of 305.523 (s)
Intv 1 Start 9570 0:14: 6
Ser.1 Avg 0.1644 Chisq 114.6 Var 0.5592E-03 Newbs. 122
Min 0.9819E-01 Max 0.2403 expVar 0.5952E-03 Bins 122
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad82034000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
2 ABELL115 PH HIGH 06/08/94 00:11:35 0.18E+05 9248 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 3624 5548 0 0 0
Writing events file
3624 events written to the output file
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 3694 5554 0 0 0
Writing events file
7318 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18420 7318 11102 0 0 0
in 36864.46 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > read events ad82034000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > filter region ad82034000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad82034000g300070_1.lc with binsize 251.875251475503
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.37E+05 7318 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/events.tmp
Total Good Bad: Region Time Phase Cut
7318 7318 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7318 7318 0 0 0 0
in 36864.46 seconds
Fits light curve has 7318 counts for 0.1985 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > set binsize 251.875251475503
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad82034000g300070_1.lc
Wrote FITS light curve to file ad82034000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad82034000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad82034000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ ABELL115 Start Time (d) .... 9570 00:11:35.424
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9571 00:35:35.436
No. of Rows ....... 143 Bin Time (s) ...... 251.9
Right Ascension ... 1.4007E+01 Internal time sys.. Converted to TJD
Declination ....... 2.6496E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 349 Newbins of 251.875 (s)
Intv 1 Start 9570 0:13:41
Ser.1 Avg 0.1990 Chisq 151.8 Var 0.8906E-03 Newbs. 143
Min 0.1310 Max 0.2859 expVar 0.8387E-03 Bins 143
Results from Statistical Analysis
Newbin Integration Time (s).. 251.88
Interval Duration (s)........ 87653.
No. of Newbins .............. 143
Average (c/s) ............... 0.19904 +/- 0.24E-02
Standard Deviation (c/s)..... 0.29843E-01
Minimum (c/s)................ 0.13102
Maximum (c/s)................ 0.28586
Variance ((c/s)**2).......... 0.89062E-03 +/- 0.11E-03
Expected Variance ((c/s)**2). 0.83872E-03 +/- 0.10E-03
Third Moment ((c/s)**3)...... 0.79795E-05
Average Deviation (c/s)...... 0.22704E-01
Skewness..................... 0.30022 +/- 0.20
Kurtosis..................... 0.38974 +/- 0.41
RMS fractional variation....< 0.83795E-01 (3 sigma)
Chi-Square................... 151.85 dof 142
Chi-Square Prob of constancy. 0.27068 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.35338 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 349 Newbins of 251.875 (s)
Intv 1 Start 9570 0:13:41
Ser.1 Avg 0.1990 Chisq 151.8 Var 0.8906E-03 Newbs. 143
Min 0.1310 Max 0.2859 expVar 0.8387E-03 Bins 143
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad82034000g200170m.evt[2] ad82034000g200270h.evt[2]-> Making L1 light curve of ft940805_2305_0035G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 38318 output records from 38353 good input G2_L1 records.-> Making L1 light curve of ft940805_2305_0035G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 33572 output records from 55301 good input G2_L1 records.-> Merging GTIs from the following files:
ad82034000g300170m.evt[2] ad82034000g300270h.evt[2]-> Making L1 light curve of ft940805_2305_0035G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 37280 output records from 37314 good input G3_L1 records.-> Making L1 light curve of ft940805_2305_0035G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 33110 output records from 53962 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 8486 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.evt
Total Good Bad: Region Time Phase Cut
8486 3061 5425 0 0 0
Writing events file
3061 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8486 3061 5425 0 0 0
in 18479.64 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > filter region ad82034000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad82034000g200170m_1.ulc use_events=yes
Wrote events list to file ad82034000g200170m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad82034000g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:33 0.18E+05 8200 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.evt
Total Good Bad: Region Time Phase Cut
8200 2974 5226 0 0 0
Writing events file
2974 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8200 2974 5226 0 0 0
in 18397.03 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > filter region ad82034000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad82034000g200270h_1.ulc use_events=yes
Wrote events list to file ad82034000g200270h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad82034000g300170m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.18E+05 9172 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.evt
Total Good Bad: Region Time Phase Cut
9172 3624 5548 0 0 0
Writing events file
3624 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9172 3624 5548 0 0 0
in 18479.44 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > filter region ad82034000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad82034000g300170m_1.ulc use_events=yes
Wrote events list to file ad82034000g300170m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad82034000g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:35 0.18E+05 9248 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.evt
Total Good Bad: Region Time Phase Cut
9248 3694 5554 0 0 0
Writing events file
3694 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9248 3694 5554 0 0 0
in 18385.03 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > filter region ad82034000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad82034000g300270h_1.ulc use_events=yes
Wrote events list to file ad82034000g300270h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad82034000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 6218 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.evt
Total Good Bad: Region Time Phase Cut
6218 3912 2306 0 0 0
Writing events file
3912 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6218 3912 2306 0 0 0
in 16869.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad82034000s000102h_1.ulc use_events=yes
Wrote events list to file ad82034000s000102h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad82034000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 6314 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000112h.evt
Total Good Bad: Region Time Phase Cut
6314 3963 2351 0 0 0
Writing events file
3963 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6314 3963 2351 0 0 0
in 16869.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad82034000s000112h_1.ulc use_events=yes
Wrote events list to file ad82034000s000112h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad82034000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 5666 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.evt
Total Good Bad: Region Time Phase Cut
5666 3650 2016 0 0 0
Writing events file
3650 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5666 3650 2016 0 0 0
in 15664.15 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad82034000s000202m_1.ulc use_events=yes
Wrote events list to file ad82034000s000202m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad82034000s000212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.16E+05 5768 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000212m.evt
Total Good Bad: Region Time Phase Cut
5768 3701 2067 0 0 0
Writing events file
3701 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5768 3701 2067 0 0 0
in 15664.15 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s000212m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad82034000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad82034000s000212m_1.ulc use_events=yes
Wrote events list to file ad82034000s000212m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad82034000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.17E+05 5181 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.evt
Total Good Bad: Region Time Phase Cut
5181 3325 1856 0 0 0
Writing events file
3325 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5181 3325 1856 0 0 0
in 16923.09 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad82034000s100102h_1.ulc use_events=yes
Wrote events list to file ad82034000s100102h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad82034000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.17E+05 5267 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100112h.evt
Total Good Bad: Region Time Phase Cut
5267 3368 1899 0 0 0
Writing events file
3368 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5267 3368 1899 0 0 0
in 16923.09 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad82034000s100112h_1.ulc use_events=yes
Wrote events list to file ad82034000s100112h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad82034000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.16E+05 4703 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.evt
Total Good Bad: Region Time Phase Cut
4703 2955 1748 0 0 0
Writing events file
2955 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4703 2955 1748 0 0 0
in 15568.15 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad82034000s100202m_1.ulc use_events=yes
Wrote events list to file ad82034000s100202m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad82034000s100212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.16E+05 4777 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100212m.evt
Total Good Bad: Region Time Phase Cut
4777 2991 1786 0 0 0
Writing events file
2991 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4777 2991 1786 0 0 0
in 15568.15 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad82034000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad82034000s100212m_1.ulc use_events=yes
Wrote events list to file ad82034000s100212m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/82034000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 19046 Total of 0 sets of frame data are extracted.
1 ad82034000g200170m.unf 68941 1 ad82034000g200270h.unf 68941-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 39189 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 39189 1024
2 ABELL115 PH HIGH 06/08/94 00:11:33 0.28E+05 29752 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.unf
Total Good Bad: Region Time Phase Cut
39189 11337 27852 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.unf
Total Good Bad: Region Time Phase Cut
29752 7809 21943 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68941 19146 49795 0 0 0
in 67667.80 seconds
Spectrum has 19146 counts for 0.2829 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 67668. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > read events ad82034000g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad82034000g220170.cal group=yes
Wrote spectrum to ad82034000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 10:06:56 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad82034000g220170.cal
Net count rate (cts/s) for file 1 0.2829 +/- 2.0451E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.4460E+06 using 84 PHA bins.
Reduced chi-squared = 1.8779E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.4334E+06 using 84 PHA bins.
Reduced chi-squared = 1.8376E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.4334E+06 using 84 PHA bins.
Reduced chi-squared = 1.8144E+04
!XSPEC> renorm
Chi-Squared = 6312. using 84 PHA bins.
Reduced chi-squared = 79.89
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
4897.8 0 1.000 5.892 0.1067 8.7892E-02
7.5854E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1638.0 0 1.000 5.858 0.1581 0.1379
6.6571E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
435.71 -1 1.000 5.904 0.1729 0.1961
4.4235E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
321.81 -2 1.000 5.940 0.1927 0.2185
2.9772E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
317.63 -3 1.000 5.933 0.1860 0.2159
3.2274E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
317.56 -4 1.000 5.934 0.1867 0.2165
3.1658E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
317.52 -5 1.000 5.934 0.1864 0.2164
3.1793E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
317.52 0 1.000 5.934 0.1865 0.2164
3.1788E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93370 +/- 0.38283E-02
3 3 2 gaussian/b Sigma 0.186452 +/- 0.41281E-02
4 4 2 gaussian/b norm 0.216413 +/- 0.22605E-02
5 2 3 gaussian/b LineE 6.53304 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.195641 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.178828E-02 +/- 0.15147E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 317.5 using 84 PHA bins.
Reduced chi-squared = 4.019
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad82034000g220170.cal peaks at 5.93370 +/- 0.0038283 keV1 ad82034000g300170m.unf 67436 1 ad82034000g300270h.unf 67436-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 38058 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 38058 1024
2 ABELL115 PH HIGH 06/08/94 00:11:35 0.28E+05 29378 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.unf
Total Good Bad: Region Time Phase Cut
38058 10321 27737 0 0 0
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.unf
Total Good Bad: Region Time Phase Cut
29378 7206 22172 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
67436 17527 49909 0 0 0
in 67657.80 seconds
Spectrum has 17527 counts for 0.2591 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 67658. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad82034000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!xsel:ASCA > read events ad82034000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > read events ad82034000g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad82034000g320170.cal group=yes
Wrote spectrum to ad82034000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 10:07:54 14-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad82034000g320170.cal
Net count rate (cts/s) for file 1 0.2591 +/- 1.9570E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.5478E+06 using 84 PHA bins.
Reduced chi-squared = 2.0101E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.5349E+06 using 84 PHA bins.
Reduced chi-squared = 1.9679E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.5349E+06 using 84 PHA bins.
Reduced chi-squared = 1.9429E+04
!XSPEC> renorm
Chi-Squared = 5944. using 84 PHA bins.
Reduced chi-squared = 75.24
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
4690.2 0 1.000 5.893 9.1800E-02 8.3420E-02
7.1418E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1652.3 0 1.000 5.867 0.1345 0.1318
6.1242E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
308.49 -1 1.000 5.922 0.1396 0.1884
3.8457E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
226.06 -2 1.000 5.942 0.1465 0.2046
3.0265E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
224.56 -3 1.000 5.939 0.1431 0.2038
3.1147E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
224.55 -4 1.000 5.939 0.1432 0.2039
3.1032E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93917 +/- 0.31327E-02
3 3 2 gaussian/b Sigma 0.143152 +/- 0.40041E-02
4 4 2 gaussian/b norm 0.203934 +/- 0.20164E-02
5 2 3 gaussian/b LineE 6.53905 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.150208 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.103242E-02 +/- 0.11953E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 224.5 using 84 PHA bins.
Reduced chi-squared = 2.842
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad82034000g320170.cal peaks at 5.93917 +/- 0.0031327 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.31E+05 60976 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000102h.unf
Total Good Bad: Region Time Phase Cut
60976 2978 0 57998 0 0
Writing events file
2978 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60976 2978 0 57998 0 0
in 2040.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad82034000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2978
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 11 2772
Flickering pixels iter, pixels & cnts : 1 3 24
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 2978
Number of image cts rejected (N, %) : 2796 93.8885193
By chip : 0 1 2 3
Pixels rejected : 0 14 0 0
Image counts : 0 2978 0 0
Image cts rejected: 0 2796 0 0
Image cts rej (%) : 0.00 93.89 0.00 0.00
filtering data...
Total counts : 0 2978 0 0
Total cts rejected: 0 2796 0 0
Total cts rej (%) : 0.00 93.89 0.00 0.00
Number of clean counts accepted : 182
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.31E+05 61478 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000112h.unf
Total Good Bad: Region Time Phase Cut
61478 3003 0 58475 0 0
Writing events file
3003 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
61478 3003 0 58475 0 0
in 2040.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad82034000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3003
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 11 2772
Flickering pixels iter, pixels & cnts : 1 3 24
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 3003
Number of image cts rejected (N, %) : 2796 93.1068954
By chip : 0 1 2 3
Pixels rejected : 0 14 0 0
Image counts : 0 3003 0 0
Image cts rejected: 0 2796 0 0
Image cts rej (%) : 0.00 93.11 0.00 0.00
filtering data...
Total counts : 0 3003 0 0
Total cts rejected: 0 2796 0 0
Total cts rej (%) : 0.00 93.11 0.00 0.00
Number of clean counts accepted : 207
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s000202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.45E+05 88514 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000202m.unf
Total Good Bad: Region Time Phase Cut
88514 11600 0 76914 0 0
Writing events file
11600 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
88514 11600 0 76914 0 0
in 5885.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad82034000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 11600
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 11011
Flickering pixels iter, pixels & cnts : 1 8 157
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 11600
Number of image cts rejected (N, %) : 11168 96.2758636
By chip : 0 1 2 3
Pixels rejected : 0 20 0 0
Image counts : 0 11600 0 0
Image cts rejected: 0 11168 0 0
Image cts rej (%) : 0.00 96.28 0.00 0.00
filtering data...
Total counts : 0 11600 0 0
Total cts rejected: 0 11168 0 0
Total cts rej (%) : 0.00 96.28 0.00 0.00
Number of clean counts accepted : 432
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s000212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.45E+05 89238 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s000212m.unf
Total Good Bad: Region Time Phase Cut
89238 11707 0 77531 0 0
Writing events file
11707 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
89238 11707 0 77531 0 0
in 5885.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad82034000s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 11707
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 11011
Flickering pixels iter, pixels & cnts : 1 8 157
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 11707
Number of image cts rejected (N, %) : 11168 95.3959198
By chip : 0 1 2 3
Pixels rejected : 0 20 0 0
Image counts : 0 11707 0 0
Image cts rejected: 0 11168 0 0
Image cts rej (%) : 0.00 95.40 0.00 0.00
filtering data...
Total counts : 0 11707 0 0
Total cts rejected: 0 11168 0 0
Total cts rej (%) : 0.00 95.40 0.00 0.00
Number of clean counts accepted : 539
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT HIGH 06/08/94 00:08:17 0.31E+05 125167 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100102h.unf
Total Good Bad: Region Time Phase Cut
125167 6936 0 118231 0 0
Writing events file
6936 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125167 6936 0 118231 0 0
in 2040.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad82034000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6936
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 24 6717
Flickering pixels iter, pixels & cnts : 1 5 66
Number of pixels rejected : 29
Number of (internal) image counts : 6936
Number of image cts rejected (N, %) : 6783 97.7941208
By chip : 0 1 2 3
Pixels rejected : 0 0 0 29
Image counts : 0 0 0 6936
Image cts rejected: 0 0 0 6783
Image cts rej (%) : 0.00 0.00 0.00 97.79
filtering data...
Total counts : 0 0 0 6936
Total cts rejected: 0 0 0 6783
Total cts rej (%) : 0.00 0.00 0.00 97.79
Number of clean counts accepted : 153
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 29
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 HIGH 06/08/94 00:08:17 0.31E+05 125520 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100112h.unf
Total Good Bad: Region Time Phase Cut
125520 6955 0 118565 0 0
Writing events file
6955 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
125520 6955 0 118565 0 0
in 2040.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad82034000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6955
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 24 6717
Flickering pixels iter, pixels & cnts : 1 5 66
Number of pixels rejected : 29
Number of (internal) image counts : 6955
Number of image cts rejected (N, %) : 6783 97.5269623
By chip : 0 1 2 3
Pixels rejected : 0 0 0 29
Image counts : 0 0 0 6955
Image cts rejected: 0 0 0 6783
Image cts rej (%) : 0.00 0.00 0.00 97.53
filtering data...
Total counts : 0 0 0 6955
Total cts rejected: 0 0 0 6783
Total cts rej (%) : 0.00 0.00 0.00 97.53
Number of clean counts accepted : 172
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 29
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s100202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT MEDIUM 05/08/94 23:05:21 0.45E+05 184530 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100202m.unf
Total Good Bad: Region Time Phase Cut
184530 25672 0 158858 0 0
Writing events file
25672 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
184530 25672 0 158858 0 0
in 5885.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad82034000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 25672
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 28 25018
Flickering pixels iter, pixels & cnts : 1 11 196
Number of pixels rejected : 39
Number of (internal) image counts : 25672
Number of image cts rejected (N, %) : 25214 98.2159576
By chip : 0 1 2 3
Pixels rejected : 0 0 0 39
Image counts : 0 0 0 25672
Image cts rejected: 0 0 0 25214
Image cts rej (%) : 0.00 0.00 0.00 98.22
filtering data...
Total counts : 0 0 0 25672
Total cts rejected: 0 0 0 25214
Total cts rej (%) : 0.00 0.00 0.00 98.22
Number of clean counts accepted : 458
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 39
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000s100212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 ABELL115 BRIGHT2 MEDIUM 05/08/94 23:05:21 0.45E+05 184980 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000s100212m.unf
Total Good Bad: Region Time Phase Cut
184980 25724 0 159256 0 0
Writing events file
25724 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
184980 25724 0 159256 0 0
in 5885.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad82034000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad82034000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 25724
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 28 25018
Flickering pixels iter, pixels & cnts : 1 11 196
Number of pixels rejected : 39
Number of (internal) image counts : 25724
Number of image cts rejected (N, %) : 25214 98.0174179
By chip : 0 1 2 3
Pixels rejected : 0 0 0 39
Image counts : 0 0 0 25724
Image cts rejected: 0 0 0 25214
Image cts rej (%) : 0.00 0.00 0.00 98.02
filtering data...
Total counts : 0 0 0 25724
Total cts rejected: 0 0 0 25214
Total cts rej (%) : 0.00 0.00 0.00 98.02
Number of clean counts accepted : 510
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 39
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad82034000g200170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 39189 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.unf
Total Good Bad: Region Time Phase Cut
39189 3321 0 35868 0 0
Writing events file
3321 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
39189 3321 0 35868 0 0
in 5711.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad82034000g200170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 39189 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200170m.unf
Total Good Bad: Region Time Phase Cut
39189 9849 0 29340 0 0
Writing events file
9849 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
39189 9849 0 29340 0 0
in 10368.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad82034000g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:33 0.28E+05 29752 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.unf
Total Good Bad: Region Time Phase Cut
29752 1029 0 28723 0 0
Writing events file
1029 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29752 1029 0 28723 0 0
in 1748.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad82034000g200270h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:33 0.28E+05 29752 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g200270h.unf
Total Good Bad: Region Time Phase Cut
29752 4550 0 25202 0 0
Writing events file
4550 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29752 4550 0 25202 0 0
in 3483.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad82034000g300170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 38058 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.unf
Total Good Bad: Region Time Phase Cut
38058 3284 0 34774 0 0
Writing events file
3284 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
38058 3284 0 34774 0 0
in 5711.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad82034000g300170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH MEDIUM 05/08/94 23:05:27 0.40E+05 38058 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300170m.unf
Total Good Bad: Region Time Phase Cut
38058 9721 0 28337 0 0
Writing events file
9721 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
38058 9721 0 28337 0 0
in 10368.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad82034000g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:35 0.28E+05 29378 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.unf
Total Good Bad: Region Time Phase Cut
29378 961 0 28417 0 0
Writing events file
961 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29378 961 0 28417 0 0
in 1748.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad82034000g300270h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 ABELL115 PH HIGH 06/08/94 00:11:35 0.28E+05 29378 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/82034000.005/ad82034000g300270h.unf
Total Good Bad: Region Time Phase Cut
29378 4372 0 25006 0 0
Writing events file
4372 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29378 4372 0 25006 0 0
in 3485.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/82034000.005/
Setting mkf directory to /data/data15/seq_proc/82034000.005/
!earthevents:ASCA > read events ad82034000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/82034000.005/
HK Directory is: /data/data15/seq_proc/82034000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files