The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 186849320.007000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-12-03 14:35:16.00700 Modified Julian Day = 51150.607824155093112-> leapsec.fits already present in current directory
Offset of 186924039.784200 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-12-04 11:20:35.78420 Modified Julian Day = 51151.472636391205015-> Observation begins 186849320.0070 1998-12-03 14:35:16
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 186849320.006900 186924051.784300
Data file start and stop ascatime : 186849320.006900 186924051.784300
Aspecting run start and stop ascatime : 186849320.007022 186924051.784171
Time interval averaged over (seconds) : 74731.777149
Total pointing and manuver time (sec) : 50147.957031 24583.984375
Mean boresight Euler angles : 190.991883 18.960173 322.885746
RA DEC SUN ANGLE
Mean solar position (deg) : 249.06 -22.04
Mean aberration (arcsec) : -30.17 -15.95
Mean sat X-axis (deg) : 152.328764 -15.016364 90.44
Mean sat Y-axis (deg) : 245.403205 -11.306260 11.29
Mean sat Z-axis (deg) : 190.991883 71.039828 101.28
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 191.853073 70.991669 232.071960 0.161100
Minimum 191.422424 70.974869 230.000946 0.000000
Maximum 191.863205 71.225342 232.593979 48.905338
Sigma (RMS) 0.003279 0.001869 0.024611 0.807224
Number of ASPECT records processed = 59399
Aspecting to RA/DEC : 191.85307312 70.99166870
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 186858257.98019 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 191.853 DEC: 70.992
START TIME: SC 186849320.0070 = UT 1998-12-03 14:35:20
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000100 16.126 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
1371.996094 13.437 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
1419.995850 10.637 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1467.995605 8.106 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
1515.995605 6.022 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1579.995483 4.110 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1643.995361 2.840 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1723.994751 1.821 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
1899.994385 0.766 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
3547.989502 0.500 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
7163.978516 0.497 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
17659.947266 0.160 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
18555.945312 0.176 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
20731.937500 0.085 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
24283.927734 0.100 F888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 7
26461.921875 0.030 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
30011.910156 0.120 188843 1 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 3
32187.904297 0.164 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
35739.894531 0.188 188843 1 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 3
37915.886719 0.164 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
41467.875000 0.180 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
43643.871094 0.040 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
47227.859375 0.145 F888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 7
49467.851562 0.052 188443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 3
52923.843750 0.086 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
55115.835938 0.019 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
58683.824219 0.048 F888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 7
60843.820312 0.020 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
64379.808594 0.051 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
66681.804688 0.027 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
70107.789062 0.057 F888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 7
72761.781250 0.040 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
74715.773438 0.060 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
74731.773438 48.905 9E03 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0
Attitude Records: 59399
Attitude Steps: 34
Maneuver ACM time: 24584.0 sec
Pointed ACM time: 50148.0 sec
-> Calculating aspect point100 99 count=12 sum1=2286.71 sum2=224.782 sum3=3880.65 100 100 count=14 sum1=2667.77 sum2=262.266 sum3=4527.66 101 99 count=111 sum1=21153 sum2=2079.01 sum3=35892.9 103 100 count=1 sum1=190.585 sum2=18.738 sum3=323.331 109 103 count=1 sum1=190.642 sum2=18.767 sum3=323.268 116 107 count=1 sum1=190.715 sum2=18.807 sum3=323.185 122 111 count=1 sum1=190.779 sum2=18.844 sum3=323.114 127 114 count=1 sum1=190.831 sum2=18.874 sum3=323.053 129 114 count=1 sum1=190.847 sum2=18.882 sum3=323.043 132 116 count=1 sum1=190.881 sum2=18.902 sum3=322.999 134 117 count=2 sum1=381.792 sum2=37.818 sum3=645.977 135 118 count=1 sum1=190.908 sum2=18.916 sum3=322.975 136 118 count=1 sum1=190.915 sum2=18.92 sum3=322.967 137 118 count=1 sum1=190.922 sum2=18.923 sum3=322.96 137 119 count=1 sum1=190.927 sum2=18.927 sum3=322.954 138 119 count=2 sum1=381.87 sum2=37.862 sum3=645.891 139 120 count=3 sum1=572.837 sum2=56.811 sum3=968.801 140 120 count=2 sum1=381.907 sum2=37.883 sum3=645.85 140 121 count=3 sum1=572.879 sum2=56.835 sum3=968.755 141 121 count=5 sum1=954.836 sum2=94.744 sum3=1614.56 142 121 count=44 sum1=8402.93 sum2=833.93 sum3=14207.7 142 122 count=952 sum1=181812 sum2=18045.4 sum3=307399 143 122 count=29423 sum1=5.6195e+06 sum2=557835 sum3=9.50032e+06 143 123 count=14 sum1=2673.85 sum2=265.495 sum3=4520.37 144 122 count=16481 sum1=3.14777e+06 sum2=312499 sum3=5.32145e+06 144 123 count=12214 sum1=2.33283e+06 sum2=231625 sum3=3.94366e+06 144 124 count=85 sum1=16235 sum2=1612.89 sum3=27443.9 145 123 count=18 sum1=3438.04 sum2=341.435 sum3=5811.74 145 124 count=2 sum1=382.004 sum2=37.951 sum3=645.736 1 out of 59399 points outside bin structure-> Euler angles: 190.992, 18.9607, 322.885
Interpolating 2 records in time interval 186850644.003 - 186850692.003 Interpolating 4 records in time interval 186850692.003 - 186850740.003 Interpolating 3 records in time interval 186850740.003 - 186850788.002 Interpolating 2 records in time interval 186850788.002 - 186850836.002 Interpolating 1 records in time interval 186850852.002 - 186850900.002 Interpolating 81 records in time interval 186924035.784 - 186924051.784
SIS1 peak error time=186856541.8606 x=33 y=221 ph0=791 ph7=880 ph8=1152 Dropping SF 1038 with invalid bit rate 7 89.9997 second gap between superframes 1133 and 1134 Warning: GIS2 bit assignment changed between 186869921.94558 and 186869923.94558 Warning: GIS3 bit assignment changed between 186869931.94555 and 186869933.94555 Warning: GIS2 bit assignment changed between 186869941.94552 and 186869943.94552 Warning: GIS3 bit assignment changed between 186869955.94548 and 186869957.94548 Dropping SF 1474 with invalid bit rate 7 1.99999 second gap between superframes 2479 and 2480 97.9997 second gap between superframes 3425 and 3426 Dropping SF 3580 with inconsistent datamode 0/31 Dropping SF 3581 with inconsistent datamode 0/11 Dropping SF 3582 with invalid bit rate 7 Dropping SF 3583 with invalid bit rate 5 GIS2 coordinate error time=186876125.31878 x=32 y=0 pha=21 rise=0 SIS0 peak error time=186876117.80218 x=60 y=88 ph0=487 ph2=1070 ph3=1418 SIS0 peak error time=186876117.80218 x=230 y=320 ph0=115 ph4=2350 ph5=3096 SIS0 coordinate error time=186876117.80218 x=75 y=0 pha[0]=0 chip=0 Dropping SF 3585 with inconsistent datamode 0/31 Warning: GIS2 bit assignment changed between 186876181.927 and 186876183.927 Warning: GIS3 bit assignment changed between 186876187.92699 and 186876189.92698 Warning: GIS2 bit assignment changed between 186876195.92696 and 186876197.92696 Warning: GIS3 bit assignment changed between 186876203.92694 and 186876205.92693 Dropping SF 3759 with inconsistent datamode 0/31 93.9997 second gap between superframes 5739 and 5740 Warning: GIS2 bit assignment changed between 186881923.90985 and 186881925.90984 Warning: GIS3 bit assignment changed between 186881929.90983 and 186881931.90982 Warning: GIS2 bit assignment changed between 186881937.9098 and 186881939.9098 Warning: GIS3 bit assignment changed between 186881945.90978 and 186881947.90978 Dropping SF 6075 with inconsistent datamode 0/14 Dropping SF 6079 with inconsistent datamode 0/31 Dropping SF 8073 with inconsistent datamode 0/31 Warning: GIS2 bit assignment changed between 186888031.89168 and 186888033.89168 Warning: GIS3 bit assignment changed between 186888041.89165 and 186888043.89165 Warning: GIS2 bit assignment changed between 186888049.89163 and 186888051.89162 Warning: GIS3 bit assignment changed between 186888057.89161 and 186888059.8916 Dropping SF 8352 with inconsistent datamode 0/31 609.998 second gap between superframes 10098 and 10099 Dropping SF 10640 with inconsistent datamode 0/31 607.998 second gap between superframes 12053 and 12054 Dropping SF 13659 with inconsistent datamode 0/16 SIS1 peak error time=186920833.66875 x=297 y=9 ph0=134 ph7=397 SIS1 peak error time=186920833.66875 x=251 y=12 ph0=129 ph7=756 SIS1 peak error time=186920833.66875 x=127 y=42 ph0=132 ph7=149 SIS1 peak error time=186920833.66875 x=327 y=113 ph0=218 ph5=1472 ph6=539 SIS1 peak error time=186920833.66875 x=376 y=192 ph0=149 ph4=3148 SIS1 peak error time=186920833.66875 x=98 y=203 ph0=127 ph4=3078 SIS1 peak error time=186920833.66875 x=368 y=213 ph0=129 ph7=1525 607.998 second gap between superframes 13977 and 13978 Dropping SF 14606 with synch code word 1 = 195 not 243 Dropping SF 14607 with synch code word 0 = 58 not 250 Dropping SF 14608 with synch code word 1 = 240 not 243 14867 of 14884 super frames processed-> Removing the following files with NEVENTS=0
ft981203_1435_1120G200170M.fits[0] ft981203_1435_1120G200270L.fits[0] ft981203_1435_1120G200370L.fits[0] ft981203_1435_1120G200870M.fits[0] ft981203_1435_1120G200970L.fits[0] ft981203_1435_1120G201070L.fits[0] ft981203_1435_1120G201370L.fits[0] ft981203_1435_1120G201870H.fits[0] ft981203_1435_1120G201970H.fits[0] ft981203_1435_1120G202070H.fits[0] ft981203_1435_1120G202170H.fits[0] ft981203_1435_1120G202670H.fits[0] ft981203_1435_1120G202770M.fits[0] ft981203_1435_1120G202870H.fits[0] ft981203_1435_1120G202970H.fits[0] ft981203_1435_1120G203470H.fits[0] ft981203_1435_1120G203570H.fits[0] ft981203_1435_1120G203670H.fits[0] ft981203_1435_1120G203770H.fits[0] ft981203_1435_1120G204370H.fits[0] ft981203_1435_1120G204470H.fits[0] ft981203_1435_1120G204570M.fits[0] ft981203_1435_1120G204670H.fits[0] ft981203_1435_1120G204770H.fits[0] ft981203_1435_1120G205270H.fits[0] ft981203_1435_1120G205370H.fits[0] ft981203_1435_1120G206070M.fits[0] ft981203_1435_1120G206170H.fits[0] ft981203_1435_1120G206270H.fits[0] ft981203_1435_1120G206370H.fits[0] ft981203_1435_1120G206670H.fits[0] ft981203_1435_1120G206770H.fits[0] ft981203_1435_1120G206870H.fits[0] ft981203_1435_1120G206970H.fits[0] ft981203_1435_1120G207570L.fits[0] ft981203_1435_1120G207670L.fits[0] ft981203_1435_1120G207770M.fits[0] ft981203_1435_1120G300170M.fits[0] ft981203_1435_1120G300270L.fits[0] ft981203_1435_1120G300370L.fits[0] ft981203_1435_1120G300870M.fits[0] ft981203_1435_1120G300970L.fits[0] ft981203_1435_1120G301070L.fits[0] ft981203_1435_1120G301370L.fits[0] ft981203_1435_1120G301970H.fits[0] ft981203_1435_1120G302070H.fits[0] ft981203_1435_1120G302170H.fits[0] ft981203_1435_1120G302270H.fits[0] ft981203_1435_1120G302370H.fits[0] ft981203_1435_1120G302470H.fits[0] ft981203_1435_1120G302670H.fits[0] ft981203_1435_1120G302770H.fits[0] ft981203_1435_1120G302870M.fits[0] ft981203_1435_1120G302970H.fits[0] ft981203_1435_1120G303070H.fits[0] ft981203_1435_1120G303770H.fits[0] ft981203_1435_1120G303870H.fits[0] ft981203_1435_1120G303970H.fits[0] ft981203_1435_1120G304070H.fits[0] ft981203_1435_1120G304170H.fits[0] ft981203_1435_1120G304470H.fits[0] ft981203_1435_1120G304570H.fits[0] ft981203_1435_1120G304670M.fits[0] ft981203_1435_1120G304770H.fits[0] ft981203_1435_1120G304870H.fits[0] ft981203_1435_1120G305070H.fits[0] ft981203_1435_1120G305470H.fits[0] ft981203_1435_1120G305570H.fits[0] ft981203_1435_1120G305670H.fits[0] ft981203_1435_1120G306170M.fits[0] ft981203_1435_1120G306270H.fits[0] ft981203_1435_1120G306370H.fits[0] ft981203_1435_1120G306970H.fits[0] ft981203_1435_1120G307070H.fits[0] ft981203_1435_1120G307170H.fits[0] ft981203_1435_1120G307270H.fits[0] ft981203_1435_1120G307770L.fits[0] ft981203_1435_1120G307870L.fits[0] ft981203_1435_1120G307970M.fits[0] ft981203_1435_1120S000101M.fits[0] ft981203_1435_1120S000801L.fits[0] ft981203_1435_1120S001701M.fits[0] ft981203_1435_1120S002001M.fits[0] ft981203_1435_1120S002401M.fits[0] ft981203_1435_1120S100101M.fits[0] ft981203_1435_1120S100801L.fits[0] ft981203_1435_1120S101701M.fits[0] ft981203_1435_1120S102001M.fits[0] ft981203_1435_1120S102401M.fits[0]-> Checking for empty GTI extensions
ft981203_1435_1120S000201L.fits[2] ft981203_1435_1120S000301L.fits[2] ft981203_1435_1120S000401M.fits[2] ft981203_1435_1120S000501H.fits[2] ft981203_1435_1120S000601M.fits[2] ft981203_1435_1120S000701L.fits[2] ft981203_1435_1120S000901L.fits[2] ft981203_1435_1120S001001M.fits[2] ft981203_1435_1120S001101H.fits[2] ft981203_1435_1120S001201L.fits[2] ft981203_1435_1120S001301L.fits[2] ft981203_1435_1120S001401M.fits[2] ft981203_1435_1120S001501H.fits[2] ft981203_1435_1120S001601M.fits[2] ft981203_1435_1120S001801H.fits[2] ft981203_1435_1120S001901M.fits[2] ft981203_1435_1120S002101M.fits[2] ft981203_1435_1120S002201H.fits[2] ft981203_1435_1120S002301M.fits[2] ft981203_1435_1120S002501H.fits[2] ft981203_1435_1120S002601L.fits[2] ft981203_1435_1120S002701M.fits[2] ft981203_1435_1120S002801H.fits[2] ft981203_1435_1120S002901L.fits[2] ft981203_1435_1120S003001H.fits[2] ft981203_1435_1120S003101L.fits[2] ft981203_1435_1120S003201M.fits[2] ft981203_1435_1120S003301L.fits[2] ft981203_1435_1120S003401M.fits[2] ft981203_1435_1120S003501L.fits[2] ft981203_1435_1120S003601M.fits[2] ft981203_1435_1120S003701H.fits[2] ft981203_1435_1120S003801M.fits[2] ft981203_1435_1120S003901H.fits[2] ft981203_1435_1120S004001M.fits[2]-> Merging GTIs from the following files:
ft981203_1435_1120S100201L.fits[2] ft981203_1435_1120S100301L.fits[2] ft981203_1435_1120S100401M.fits[2] ft981203_1435_1120S100501H.fits[2] ft981203_1435_1120S100601M.fits[2] ft981203_1435_1120S100701L.fits[2] ft981203_1435_1120S100901L.fits[2] ft981203_1435_1120S101001M.fits[2] ft981203_1435_1120S101101H.fits[2] ft981203_1435_1120S101201L.fits[2] ft981203_1435_1120S101301L.fits[2] ft981203_1435_1120S101401M.fits[2] ft981203_1435_1120S101501H.fits[2] ft981203_1435_1120S101601M.fits[2] ft981203_1435_1120S101801H.fits[2] ft981203_1435_1120S101901M.fits[2] ft981203_1435_1120S102101M.fits[2] ft981203_1435_1120S102201H.fits[2] ft981203_1435_1120S102301M.fits[2] ft981203_1435_1120S102501H.fits[2] ft981203_1435_1120S102601L.fits[2] ft981203_1435_1120S102701M.fits[2] ft981203_1435_1120S102801H.fits[2] ft981203_1435_1120S102901L.fits[2] ft981203_1435_1120S103001H.fits[2] ft981203_1435_1120S103101L.fits[2] ft981203_1435_1120S103201M.fits[2] ft981203_1435_1120S103301L.fits[2] ft981203_1435_1120S103401M.fits[2] ft981203_1435_1120S103501L.fits[2] ft981203_1435_1120S103601M.fits[2] ft981203_1435_1120S103701H.fits[2] ft981203_1435_1120S103801M.fits[2] ft981203_1435_1120S103901H.fits[2] ft981203_1435_1120S104001M.fits[2]-> Merging GTIs from the following files:
ft981203_1435_1120G200470L.fits[2] ft981203_1435_1120G200570M.fits[2] ft981203_1435_1120G200670H.fits[2] ft981203_1435_1120G200770M.fits[2] ft981203_1435_1120G201170M.fits[2] ft981203_1435_1120G201270H.fits[2] ft981203_1435_1120G201470L.fits[2] ft981203_1435_1120G201570M.fits[2] ft981203_1435_1120G201670H.fits[2] ft981203_1435_1120G201770H.fits[2] ft981203_1435_1120G202270H.fits[2] ft981203_1435_1120G202370H.fits[2] ft981203_1435_1120G202470H.fits[2] ft981203_1435_1120G202570H.fits[2] ft981203_1435_1120G203070H.fits[2] ft981203_1435_1120G203170H.fits[2] ft981203_1435_1120G203270H.fits[2] ft981203_1435_1120G203370H.fits[2] ft981203_1435_1120G203870H.fits[2] ft981203_1435_1120G203970H.fits[2] ft981203_1435_1120G204070H.fits[2] ft981203_1435_1120G204170H.fits[2] ft981203_1435_1120G204270H.fits[2] ft981203_1435_1120G204870H.fits[2] ft981203_1435_1120G204970H.fits[2] ft981203_1435_1120G205070H.fits[2] ft981203_1435_1120G205170H.fits[2] ft981203_1435_1120G205470H.fits[2] ft981203_1435_1120G205570H.fits[2] ft981203_1435_1120G205670H.fits[2] ft981203_1435_1120G205770H.fits[2] ft981203_1435_1120G205870H.fits[2] ft981203_1435_1120G205970M.fits[2] ft981203_1435_1120G206470H.fits[2] ft981203_1435_1120G206570H.fits[2] ft981203_1435_1120G207070H.fits[2] ft981203_1435_1120G207170H.fits[2] ft981203_1435_1120G207270H.fits[2] ft981203_1435_1120G207370L.fits[2] ft981203_1435_1120G207470L.fits[2] ft981203_1435_1120G207870M.fits[2] ft981203_1435_1120G207970M.fits[2] ft981203_1435_1120G208070H.fits[2] ft981203_1435_1120G208170L.fits[2] ft981203_1435_1120G208270H.fits[2] ft981203_1435_1120G208370L.fits[2] ft981203_1435_1120G208470M.fits[2] ft981203_1435_1120G208570M.fits[2] ft981203_1435_1120G208670M.fits[2] ft981203_1435_1120G208770M.fits[2] ft981203_1435_1120G208870L.fits[2] ft981203_1435_1120G208970L.fits[2] ft981203_1435_1120G209070M.fits[2] ft981203_1435_1120G209170L.fits[2] ft981203_1435_1120G209270L.fits[2] ft981203_1435_1120G209370M.fits[2] ft981203_1435_1120G209470M.fits[2] ft981203_1435_1120G209570M.fits[2] ft981203_1435_1120G209670M.fits[2] ft981203_1435_1120G209770H.fits[2] ft981203_1435_1120G209870M.fits[2] ft981203_1435_1120G209970H.fits[2] ft981203_1435_1120G210070M.fits[2]-> Merging GTIs from the following files:
ft981203_1435_1120G300470L.fits[2] ft981203_1435_1120G300570M.fits[2] ft981203_1435_1120G300670H.fits[2] ft981203_1435_1120G300770M.fits[2] ft981203_1435_1120G301170M.fits[2] ft981203_1435_1120G301270H.fits[2] ft981203_1435_1120G301470L.fits[2] ft981203_1435_1120G301570M.fits[2] ft981203_1435_1120G301670H.fits[2] ft981203_1435_1120G301770H.fits[2] ft981203_1435_1120G301870H.fits[2] ft981203_1435_1120G302570H.fits[2] ft981203_1435_1120G303170H.fits[2] ft981203_1435_1120G303270H.fits[2] ft981203_1435_1120G303370H.fits[2] ft981203_1435_1120G303470H.fits[2] ft981203_1435_1120G303570H.fits[2] ft981203_1435_1120G303670H.fits[2] ft981203_1435_1120G304270H.fits[2] ft981203_1435_1120G304370H.fits[2] ft981203_1435_1120G304970H.fits[2] ft981203_1435_1120G305170H.fits[2] ft981203_1435_1120G305270H.fits[2] ft981203_1435_1120G305370H.fits[2] ft981203_1435_1120G305770H.fits[2] ft981203_1435_1120G305870H.fits[2] ft981203_1435_1120G305970H.fits[2] ft981203_1435_1120G306070M.fits[2] ft981203_1435_1120G306470H.fits[2] ft981203_1435_1120G306570H.fits[2] ft981203_1435_1120G306670H.fits[2] ft981203_1435_1120G306770H.fits[2] ft981203_1435_1120G306870H.fits[2] ft981203_1435_1120G307370H.fits[2] ft981203_1435_1120G307470H.fits[2] ft981203_1435_1120G307570L.fits[2] ft981203_1435_1120G307670L.fits[2] ft981203_1435_1120G308070M.fits[2] ft981203_1435_1120G308170M.fits[2] ft981203_1435_1120G308270H.fits[2] ft981203_1435_1120G308370L.fits[2] ft981203_1435_1120G308470H.fits[2] ft981203_1435_1120G308570L.fits[2] ft981203_1435_1120G308670M.fits[2] ft981203_1435_1120G308770M.fits[2] ft981203_1435_1120G308870M.fits[2] ft981203_1435_1120G308970M.fits[2] ft981203_1435_1120G309070L.fits[2] ft981203_1435_1120G309170L.fits[2] ft981203_1435_1120G309270M.fits[2] ft981203_1435_1120G309370L.fits[2] ft981203_1435_1120G309470L.fits[2] ft981203_1435_1120G309570M.fits[2] ft981203_1435_1120G309670M.fits[2] ft981203_1435_1120G309770M.fits[2] ft981203_1435_1120G309870M.fits[2] ft981203_1435_1120G309970H.fits[2] ft981203_1435_1120G310070M.fits[2] ft981203_1435_1120G310170H.fits[2] ft981203_1435_1120G310270M.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200470h.prelist merge count = 2 photon cnt = 4 GISSORTSPLIT:LO:g200570h.prelist merge count = 3 photon cnt = 6 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200770h.prelist merge count = 17 photon cnt = 25634 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g201070h.prelist merge count = 4 photon cnt = 22 GISSORTSPLIT:LO:g201170h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 30 GISSORTSPLIT:LO:g200270l.prelist merge count = 6 photon cnt = 14860 GISSORTSPLIT:LO:g200370l.prelist merge count = 3 photon cnt = 1508 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200270m.prelist merge count = 11 photon cnt = 16284 GISSORTSPLIT:LO:g200370m.prelist merge count = 2 photon cnt = 14 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:Total filenames split = 63 GISSORTSPLIT:LO:Total split file cnt = 21 GISSORTSPLIT:LO:End program-> Creating ad86046000g200170h.unf
---- cmerge: version 1.6 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G200670H.fits 2 -- ft981203_1435_1120G201270H.fits 3 -- ft981203_1435_1120G201670H.fits 4 -- ft981203_1435_1120G201770H.fits 5 -- ft981203_1435_1120G202470H.fits 6 -- ft981203_1435_1120G203270H.fits 7 -- ft981203_1435_1120G203370H.fits 8 -- ft981203_1435_1120G204270H.fits 9 -- ft981203_1435_1120G205070H.fits 10 -- ft981203_1435_1120G205770H.fits 11 -- ft981203_1435_1120G205870H.fits 12 -- ft981203_1435_1120G206570H.fits 13 -- ft981203_1435_1120G207270H.fits 14 -- ft981203_1435_1120G208070H.fits 15 -- ft981203_1435_1120G208270H.fits 16 -- ft981203_1435_1120G209770H.fits 17 -- ft981203_1435_1120G209970H.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G200670H.fits 2 -- ft981203_1435_1120G201270H.fits 3 -- ft981203_1435_1120G201670H.fits 4 -- ft981203_1435_1120G201770H.fits 5 -- ft981203_1435_1120G202470H.fits 6 -- ft981203_1435_1120G203270H.fits 7 -- ft981203_1435_1120G203370H.fits 8 -- ft981203_1435_1120G204270H.fits 9 -- ft981203_1435_1120G205070H.fits 10 -- ft981203_1435_1120G205770H.fits 11 -- ft981203_1435_1120G205870H.fits 12 -- ft981203_1435_1120G206570H.fits 13 -- ft981203_1435_1120G207270H.fits 14 -- ft981203_1435_1120G208070H.fits 15 -- ft981203_1435_1120G208270H.fits 16 -- ft981203_1435_1120G209770H.fits 17 -- ft981203_1435_1120G209970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g200270m.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G200570M.fits 2 -- ft981203_1435_1120G200770M.fits 3 -- ft981203_1435_1120G201170M.fits 4 -- ft981203_1435_1120G201570M.fits 5 -- ft981203_1435_1120G205970M.fits 6 -- ft981203_1435_1120G207970M.fits 7 -- ft981203_1435_1120G208770M.fits 8 -- ft981203_1435_1120G209070M.fits 9 -- ft981203_1435_1120G209670M.fits 10 -- ft981203_1435_1120G209870M.fits 11 -- ft981203_1435_1120G210070M.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G200570M.fits 2 -- ft981203_1435_1120G200770M.fits 3 -- ft981203_1435_1120G201170M.fits 4 -- ft981203_1435_1120G201570M.fits 5 -- ft981203_1435_1120G205970M.fits 6 -- ft981203_1435_1120G207970M.fits 7 -- ft981203_1435_1120G208770M.fits 8 -- ft981203_1435_1120G209070M.fits 9 -- ft981203_1435_1120G209670M.fits 10 -- ft981203_1435_1120G209870M.fits 11 -- ft981203_1435_1120G210070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g200370l.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G200470L.fits 2 -- ft981203_1435_1120G207470L.fits 3 -- ft981203_1435_1120G208170L.fits 4 -- ft981203_1435_1120G208370L.fits 5 -- ft981203_1435_1120G208970L.fits 6 -- ft981203_1435_1120G209270L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G200470L.fits 2 -- ft981203_1435_1120G207470L.fits 3 -- ft981203_1435_1120G208170L.fits 4 -- ft981203_1435_1120G208370L.fits 5 -- ft981203_1435_1120G208970L.fits 6 -- ft981203_1435_1120G209270L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g200470l.unf
---- cmerge: version 1.6 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G207370L.fits 2 -- ft981203_1435_1120G208870L.fits 3 -- ft981203_1435_1120G209170L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G207370L.fits 2 -- ft981203_1435_1120G208870L.fits 3 -- ft981203_1435_1120G209170L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000030 events
ft981203_1435_1120G201470L.fits-> Ignoring the following files containing 000000022 events
ft981203_1435_1120G202270H.fits ft981203_1435_1120G204070H.fits ft981203_1435_1120G205670H.fits ft981203_1435_1120G207070H.fits-> Ignoring the following files containing 000000014 events
ft981203_1435_1120G208670M.fits ft981203_1435_1120G209570M.fits-> Ignoring the following files containing 000000012 events
ft981203_1435_1120G207870M.fits-> Ignoring the following files containing 000000009 events
ft981203_1435_1120G208470M.fits-> Ignoring the following files containing 000000008 events
ft981203_1435_1120G208570M.fits-> Ignoring the following files containing 000000007 events
ft981203_1435_1120G202370H.fits ft981203_1435_1120G204170H.fits ft981203_1435_1120G207170H.fits-> Ignoring the following files containing 000000006 events
ft981203_1435_1120G209470M.fits-> Ignoring the following files containing 000000006 events
ft981203_1435_1120G203170H.fits ft981203_1435_1120G204970H.fits ft981203_1435_1120G206470H.fits-> Ignoring the following files containing 000000004 events
ft981203_1435_1120G205570H.fits-> Ignoring the following files containing 000000004 events
ft981203_1435_1120G209370M.fits-> Ignoring the following files containing 000000004 events
ft981203_1435_1120G203070H.fits ft981203_1435_1120G204870H.fits-> Ignoring the following files containing 000000002 events
ft981203_1435_1120G203970H.fits-> Ignoring the following files containing 000000002 events
ft981203_1435_1120G205170H.fits-> Ignoring the following files containing 000000002 events
ft981203_1435_1120G205470H.fits-> Ignoring the following files containing 000000001 events
ft981203_1435_1120G202570H.fits-> Ignoring the following files containing 000000001 events
ft981203_1435_1120G203870H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 3 photon cnt = 9 GISSORTSPLIT:LO:g300270h.prelist merge count = 2 photon cnt = 7 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300570h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300670h.prelist merge count = 17 photon cnt = 24538 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300970h.prelist merge count = 4 photon cnt = 23 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g300270l.prelist merge count = 6 photon cnt = 14641 GISSORTSPLIT:LO:g300370l.prelist merge count = 3 photon cnt = 1499 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g300270m.prelist merge count = 11 photon cnt = 15703 GISSORTSPLIT:LO:g300370m.prelist merge count = 2 photon cnt = 18 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:Total filenames split = 60 GISSORTSPLIT:LO:Total split file cnt = 19 GISSORTSPLIT:LO:End program-> Creating ad86046000g300170h.unf
---- cmerge: version 1.6 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G300670H.fits 2 -- ft981203_1435_1120G301270H.fits 3 -- ft981203_1435_1120G301670H.fits 4 -- ft981203_1435_1120G301770H.fits 5 -- ft981203_1435_1120G302570H.fits 6 -- ft981203_1435_1120G303370H.fits 7 -- ft981203_1435_1120G303470H.fits 8 -- ft981203_1435_1120G304370H.fits 9 -- ft981203_1435_1120G305170H.fits 10 -- ft981203_1435_1120G305870H.fits 11 -- ft981203_1435_1120G305970H.fits 12 -- ft981203_1435_1120G306670H.fits 13 -- ft981203_1435_1120G307470H.fits 14 -- ft981203_1435_1120G308270H.fits 15 -- ft981203_1435_1120G308470H.fits 16 -- ft981203_1435_1120G309970H.fits 17 -- ft981203_1435_1120G310170H.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G300670H.fits 2 -- ft981203_1435_1120G301270H.fits 3 -- ft981203_1435_1120G301670H.fits 4 -- ft981203_1435_1120G301770H.fits 5 -- ft981203_1435_1120G302570H.fits 6 -- ft981203_1435_1120G303370H.fits 7 -- ft981203_1435_1120G303470H.fits 8 -- ft981203_1435_1120G304370H.fits 9 -- ft981203_1435_1120G305170H.fits 10 -- ft981203_1435_1120G305870H.fits 11 -- ft981203_1435_1120G305970H.fits 12 -- ft981203_1435_1120G306670H.fits 13 -- ft981203_1435_1120G307470H.fits 14 -- ft981203_1435_1120G308270H.fits 15 -- ft981203_1435_1120G308470H.fits 16 -- ft981203_1435_1120G309970H.fits 17 -- ft981203_1435_1120G310170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g300270m.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G300570M.fits 2 -- ft981203_1435_1120G300770M.fits 3 -- ft981203_1435_1120G301170M.fits 4 -- ft981203_1435_1120G301570M.fits 5 -- ft981203_1435_1120G306070M.fits 6 -- ft981203_1435_1120G308170M.fits 7 -- ft981203_1435_1120G308970M.fits 8 -- ft981203_1435_1120G309270M.fits 9 -- ft981203_1435_1120G309870M.fits 10 -- ft981203_1435_1120G310070M.fits 11 -- ft981203_1435_1120G310270M.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G300570M.fits 2 -- ft981203_1435_1120G300770M.fits 3 -- ft981203_1435_1120G301170M.fits 4 -- ft981203_1435_1120G301570M.fits 5 -- ft981203_1435_1120G306070M.fits 6 -- ft981203_1435_1120G308170M.fits 7 -- ft981203_1435_1120G308970M.fits 8 -- ft981203_1435_1120G309270M.fits 9 -- ft981203_1435_1120G309870M.fits 10 -- ft981203_1435_1120G310070M.fits 11 -- ft981203_1435_1120G310270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g300370l.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G300470L.fits 2 -- ft981203_1435_1120G307670L.fits 3 -- ft981203_1435_1120G308370L.fits 4 -- ft981203_1435_1120G308570L.fits 5 -- ft981203_1435_1120G309170L.fits 6 -- ft981203_1435_1120G309470L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G300470L.fits 2 -- ft981203_1435_1120G307670L.fits 3 -- ft981203_1435_1120G308370L.fits 4 -- ft981203_1435_1120G308570L.fits 5 -- ft981203_1435_1120G309170L.fits 6 -- ft981203_1435_1120G309470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000g300470l.unf
---- cmerge: version 1.6 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120G307570L.fits 2 -- ft981203_1435_1120G309070L.fits 3 -- ft981203_1435_1120G309370L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120G307570L.fits 2 -- ft981203_1435_1120G309070L.fits 3 -- ft981203_1435_1120G309370L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000023 events
ft981203_1435_1120G301870H.fits ft981203_1435_1120G303570H.fits ft981203_1435_1120G305370H.fits ft981203_1435_1120G306870H.fits-> Ignoring the following files containing 000000018 events
ft981203_1435_1120G308870M.fits ft981203_1435_1120G309770M.fits-> Ignoring the following files containing 000000014 events
ft981203_1435_1120G301470L.fits-> Ignoring the following files containing 000000013 events
ft981203_1435_1120G308070M.fits-> Ignoring the following files containing 000000010 events
ft981203_1435_1120G308670M.fits-> Ignoring the following files containing 000000009 events
ft981203_1435_1120G303170H.fits ft981203_1435_1120G304970H.fits ft981203_1435_1120G306470H.fits-> Ignoring the following files containing 000000007 events
ft981203_1435_1120G309670M.fits-> Ignoring the following files containing 000000007 events
ft981203_1435_1120G303270H.fits ft981203_1435_1120G306570H.fits-> Ignoring the following files containing 000000005 events
ft981203_1435_1120G305270H.fits ft981203_1435_1120G306770H.fits-> Ignoring the following files containing 000000004 events
ft981203_1435_1120G308770M.fits-> Ignoring the following files containing 000000004 events
ft981203_1435_1120G309570M.fits-> Ignoring the following files containing 000000003 events
ft981203_1435_1120G307370H.fits-> Ignoring the following files containing 000000002 events
ft981203_1435_1120G303670H.fits-> Ignoring the following files containing 000000002 events
ft981203_1435_1120G304270H.fits-> Ignoring the following files containing 000000001 events
ft981203_1435_1120G305770H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 10 photon cnt = 165256 SIS0SORTSPLIT:LO:s000201l.prelist merge count = 9 photon cnt = 21833 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 2 photon cnt = 79 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 14 photon cnt = 59528 SIS0SORTSPLIT:LO:Total filenames split = 35 SIS0SORTSPLIT:LO:Total split file cnt = 4 SIS0SORTSPLIT:LO:End program-> Creating ad86046000s000101h.unf
---- cmerge: version 1.6 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S000501H.fits 2 -- ft981203_1435_1120S001101H.fits 3 -- ft981203_1435_1120S001501H.fits 4 -- ft981203_1435_1120S001801H.fits 5 -- ft981203_1435_1120S002201H.fits 6 -- ft981203_1435_1120S002501H.fits 7 -- ft981203_1435_1120S002801H.fits 8 -- ft981203_1435_1120S003001H.fits 9 -- ft981203_1435_1120S003701H.fits 10 -- ft981203_1435_1120S003901H.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S000501H.fits 2 -- ft981203_1435_1120S001101H.fits 3 -- ft981203_1435_1120S001501H.fits 4 -- ft981203_1435_1120S001801H.fits 5 -- ft981203_1435_1120S002201H.fits 6 -- ft981203_1435_1120S002501H.fits 7 -- ft981203_1435_1120S002801H.fits 8 -- ft981203_1435_1120S003001H.fits 9 -- ft981203_1435_1120S003701H.fits 10 -- ft981203_1435_1120S003901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000s000201m.unf
---- cmerge: version 1.6 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S000401M.fits 2 -- ft981203_1435_1120S000601M.fits 3 -- ft981203_1435_1120S001001M.fits 4 -- ft981203_1435_1120S001401M.fits 5 -- ft981203_1435_1120S001601M.fits 6 -- ft981203_1435_1120S001901M.fits 7 -- ft981203_1435_1120S002101M.fits 8 -- ft981203_1435_1120S002301M.fits 9 -- ft981203_1435_1120S002701M.fits 10 -- ft981203_1435_1120S003201M.fits 11 -- ft981203_1435_1120S003401M.fits 12 -- ft981203_1435_1120S003601M.fits 13 -- ft981203_1435_1120S003801M.fits 14 -- ft981203_1435_1120S004001M.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S000401M.fits 2 -- ft981203_1435_1120S000601M.fits 3 -- ft981203_1435_1120S001001M.fits 4 -- ft981203_1435_1120S001401M.fits 5 -- ft981203_1435_1120S001601M.fits 6 -- ft981203_1435_1120S001901M.fits 7 -- ft981203_1435_1120S002101M.fits 8 -- ft981203_1435_1120S002301M.fits 9 -- ft981203_1435_1120S002701M.fits 10 -- ft981203_1435_1120S003201M.fits 11 -- ft981203_1435_1120S003401M.fits 12 -- ft981203_1435_1120S003601M.fits 13 -- ft981203_1435_1120S003801M.fits 14 -- ft981203_1435_1120S004001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000s000301l.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S000301L.fits 2 -- ft981203_1435_1120S000701L.fits 3 -- ft981203_1435_1120S000901L.fits 4 -- ft981203_1435_1120S001301L.fits 5 -- ft981203_1435_1120S002601L.fits 6 -- ft981203_1435_1120S002901L.fits 7 -- ft981203_1435_1120S003101L.fits 8 -- ft981203_1435_1120S003301L.fits 9 -- ft981203_1435_1120S003501L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S000301L.fits 2 -- ft981203_1435_1120S000701L.fits 3 -- ft981203_1435_1120S000901L.fits 4 -- ft981203_1435_1120S001301L.fits 5 -- ft981203_1435_1120S002601L.fits 6 -- ft981203_1435_1120S002901L.fits 7 -- ft981203_1435_1120S003101L.fits 8 -- ft981203_1435_1120S003301L.fits 9 -- ft981203_1435_1120S003501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000079 events
ft981203_1435_1120S000201L.fits ft981203_1435_1120S001201L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 10 photon cnt = 223650 SIS1SORTSPLIT:LO:s100201l.prelist merge count = 9 photon cnt = 22311 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 2 photon cnt = 80 SIS1SORTSPLIT:LO:s100401m.prelist merge count = 14 photon cnt = 98205 SIS1SORTSPLIT:LO:Total filenames split = 35 SIS1SORTSPLIT:LO:Total split file cnt = 4 SIS1SORTSPLIT:LO:End program-> Creating ad86046000s100101h.unf
---- cmerge: version 1.6 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S100501H.fits 2 -- ft981203_1435_1120S101101H.fits 3 -- ft981203_1435_1120S101501H.fits 4 -- ft981203_1435_1120S101801H.fits 5 -- ft981203_1435_1120S102201H.fits 6 -- ft981203_1435_1120S102501H.fits 7 -- ft981203_1435_1120S102801H.fits 8 -- ft981203_1435_1120S103001H.fits 9 -- ft981203_1435_1120S103701H.fits 10 -- ft981203_1435_1120S103901H.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S100501H.fits 2 -- ft981203_1435_1120S101101H.fits 3 -- ft981203_1435_1120S101501H.fits 4 -- ft981203_1435_1120S101801H.fits 5 -- ft981203_1435_1120S102201H.fits 6 -- ft981203_1435_1120S102501H.fits 7 -- ft981203_1435_1120S102801H.fits 8 -- ft981203_1435_1120S103001H.fits 9 -- ft981203_1435_1120S103701H.fits 10 -- ft981203_1435_1120S103901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000s100201m.unf
---- cmerge: version 1.6 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S100401M.fits 2 -- ft981203_1435_1120S100601M.fits 3 -- ft981203_1435_1120S101001M.fits 4 -- ft981203_1435_1120S101401M.fits 5 -- ft981203_1435_1120S101601M.fits 6 -- ft981203_1435_1120S101901M.fits 7 -- ft981203_1435_1120S102101M.fits 8 -- ft981203_1435_1120S102301M.fits 9 -- ft981203_1435_1120S102701M.fits 10 -- ft981203_1435_1120S103201M.fits 11 -- ft981203_1435_1120S103401M.fits 12 -- ft981203_1435_1120S103601M.fits 13 -- ft981203_1435_1120S103801M.fits 14 -- ft981203_1435_1120S104001M.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S100401M.fits 2 -- ft981203_1435_1120S100601M.fits 3 -- ft981203_1435_1120S101001M.fits 4 -- ft981203_1435_1120S101401M.fits 5 -- ft981203_1435_1120S101601M.fits 6 -- ft981203_1435_1120S101901M.fits 7 -- ft981203_1435_1120S102101M.fits 8 -- ft981203_1435_1120S102301M.fits 9 -- ft981203_1435_1120S102701M.fits 10 -- ft981203_1435_1120S103201M.fits 11 -- ft981203_1435_1120S103401M.fits 12 -- ft981203_1435_1120S103601M.fits 13 -- ft981203_1435_1120S103801M.fits 14 -- ft981203_1435_1120S104001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86046000s100301l.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft981203_1435_1120S100301L.fits 2 -- ft981203_1435_1120S100701L.fits 3 -- ft981203_1435_1120S100901L.fits 4 -- ft981203_1435_1120S101301L.fits 5 -- ft981203_1435_1120S102601L.fits 6 -- ft981203_1435_1120S102901L.fits 7 -- ft981203_1435_1120S103101L.fits 8 -- ft981203_1435_1120S103301L.fits 9 -- ft981203_1435_1120S103501L.fits Merging binary extension #: 2 1 -- ft981203_1435_1120S100301L.fits 2 -- ft981203_1435_1120S100701L.fits 3 -- ft981203_1435_1120S100901L.fits 4 -- ft981203_1435_1120S101301L.fits 5 -- ft981203_1435_1120S102601L.fits 6 -- ft981203_1435_1120S102901L.fits 7 -- ft981203_1435_1120S103101L.fits 8 -- ft981203_1435_1120S103301L.fits 9 -- ft981203_1435_1120S103501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000080 events
ft981203_1435_1120S100201L.fits ft981203_1435_1120S101201L.fits-> Tar-ing together the leftover raw files
a ft981203_1435_1120G201470L.fits 31K a ft981203_1435_1120G202270H.fits 31K a ft981203_1435_1120G202370H.fits 31K a ft981203_1435_1120G202570H.fits 31K a ft981203_1435_1120G203070H.fits 31K a ft981203_1435_1120G203170H.fits 31K a ft981203_1435_1120G203870H.fits 31K a ft981203_1435_1120G203970H.fits 31K a ft981203_1435_1120G204070H.fits 31K a ft981203_1435_1120G204170H.fits 31K a ft981203_1435_1120G204870H.fits 31K a ft981203_1435_1120G204970H.fits 31K a ft981203_1435_1120G205170H.fits 31K a ft981203_1435_1120G205470H.fits 31K a ft981203_1435_1120G205570H.fits 31K a ft981203_1435_1120G205670H.fits 31K a ft981203_1435_1120G206470H.fits 31K a ft981203_1435_1120G207070H.fits 31K a ft981203_1435_1120G207170H.fits 31K a ft981203_1435_1120G207870M.fits 31K a ft981203_1435_1120G208470M.fits 31K a ft981203_1435_1120G208570M.fits 31K a ft981203_1435_1120G208670M.fits 31K a ft981203_1435_1120G209370M.fits 31K a ft981203_1435_1120G209470M.fits 31K a ft981203_1435_1120G209570M.fits 31K a ft981203_1435_1120G301470L.fits 31K a ft981203_1435_1120G301870H.fits 31K a ft981203_1435_1120G303170H.fits 31K a ft981203_1435_1120G303270H.fits 31K a ft981203_1435_1120G303570H.fits 31K a ft981203_1435_1120G303670H.fits 31K a ft981203_1435_1120G304270H.fits 31K a ft981203_1435_1120G304970H.fits 31K a ft981203_1435_1120G305270H.fits 31K a ft981203_1435_1120G305370H.fits 31K a ft981203_1435_1120G305770H.fits 31K a ft981203_1435_1120G306470H.fits 31K a ft981203_1435_1120G306570H.fits 31K a ft981203_1435_1120G306770H.fits 31K a ft981203_1435_1120G306870H.fits 31K a ft981203_1435_1120G307370H.fits 31K a ft981203_1435_1120G308070M.fits 31K a ft981203_1435_1120G308670M.fits 31K a ft981203_1435_1120G308770M.fits 31K a ft981203_1435_1120G308870M.fits 31K a ft981203_1435_1120G309570M.fits 31K a ft981203_1435_1120G309670M.fits 31K a ft981203_1435_1120G309770M.fits 31K a ft981203_1435_1120S000201L.fits 29K a ft981203_1435_1120S001201L.fits 29K a ft981203_1435_1120S100201L.fits 29K a ft981203_1435_1120S101201L.fits 29K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft981203_1435.1120' is successfully opened Data Start Time is 186849318.01 (19981203 143514) Time Margin 2.0 sec included Sync error detected in 14591 th SF Sync error detected in 14592 th SF Sync error detected in 14593 th SF 'ft981203_1435.1120' EOF detected, sf=14884 Data End Time is 186924041.78 (19981204 112037) Gain History is written in ft981203_1435_1120.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft981203_1435_1120.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft981203_1435_1120.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft981203_1435_1120CMHK.fits
The sum of the selected column is 58724.000 The mean of the selected column is 106.57713 The standard deviation of the selected column is 1.6854845 The minimum of selected column is 104.00000 The maximum of selected column is 110.00000 The number of points used in calculation is 551-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 58724.000 The mean of the selected column is 106.57713 The standard deviation of the selected column is 1.6854845 The minimum of selected column is 104.00000 The maximum of selected column is 110.00000 The number of points used in calculation is 551
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g200270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g200470l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86046000g300170h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g300270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000g300470l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86046000s000101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s000312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86046000s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 186858257.98019 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:
S0-HK file: ft981203_1435_1120S0HK.fits
S1-HK file: ft981203_1435_1120S1HK.fits
G2-HK file: ft981203_1435_1120G2HK.fits
G3-HK file: ft981203_1435_1120G3HK.fits
Date and time are: 1998-12-03 14:34:16 mjd=51150.607130
Orbit file name is ./frf.orbit.240v2
Epoch of Orbital Elements: 1998-11-30 21:00:00
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa981203_1435.1120
output FITS File: ft981203_1435_1120.mkf
mkfilter2: Warning, faQparam error: time= 1.868492720070e+08 outside range of attitude file
Euler angles undefined for this bin
Total 2337 Data bins were processed.
-> Checking if column TIME in ft981203_1435_1120.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 11084.421 The mean of the selected column is 18.052804 The standard deviation of the selected column is 7.1352834 The minimum of selected column is 3.3750100 The maximum of selected column is 48.500145 The number of points used in calculation is 614-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<39.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad86046000s000112h.unf into ad86046000s000112h.evt
The sum of the selected column is 11084.421 The mean of the selected column is 18.052804 The standard deviation of the selected column is 7.1352834 The minimum of selected column is 3.3750100 The maximum of selected column is 48.500145 The number of points used in calculation is 614-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<39.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad86046000s000201m.unf because of mode
The sum of the selected column is 5561.6208 The mean of the selected column is 17.655939 The standard deviation of the selected column is 6.6470617 The minimum of selected column is 4.7500143 The maximum of selected column is 44.781384 The number of points used in calculation is 315-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<37.5 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad86046000s000212m.unf into ad86046000s000212m.evt
The sum of the selected column is 5561.6208 The mean of the selected column is 17.655939 The standard deviation of the selected column is 6.6470617 The minimum of selected column is 4.7500143 The maximum of selected column is 44.781384 The number of points used in calculation is 315-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<37.5 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad86046000s000301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad86046000s000302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad86046000s000312l.evt since it contains 0 events
The sum of the selected column is 18941.486 The mean of the selected column is 30.799164 The standard deviation of the selected column is 12.143960 The minimum of selected column is 6.9615588 The maximum of selected column is 97.500290 The number of points used in calculation is 615-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<67.2 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad86046000s100112h.unf into ad86046000s100112h.evt
The sum of the selected column is 18941.486 The mean of the selected column is 30.799164 The standard deviation of the selected column is 12.143960 The minimum of selected column is 6.9615588 The maximum of selected column is 97.500290 The number of points used in calculation is 615-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<67.2 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad86046000s100201m.unf because of mode
The sum of the selected column is 5432.9433 The mean of the selected column is 26.502162 The standard deviation of the selected column is 8.9403438 The minimum of selected column is 11.187533 The maximum of selected column is 69.812706 The number of points used in calculation is 205-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<53.3 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad86046000s100212m.unf into ad86046000s100212m.evt
The sum of the selected column is 5432.9433 The mean of the selected column is 26.502162 The standard deviation of the selected column is 8.9403438 The minimum of selected column is 11.187533 The maximum of selected column is 69.812706 The number of points used in calculation is 205-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<53.3 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad86046000s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad86046000s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad86046000s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad86046000g200270m.unf into ad86046000g200270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad86046000g200370l.unf into ad86046000g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Deleting ad86046000g200370l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Deleting ad86046000g200470l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad86046000g300270m.unf into ad86046000g300270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad86046000g300370l.unf into ad86046000g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Deleting ad86046000g300370l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Deleting ad86046000g300470l.evt since it contains 0 events
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad86046000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0148
Mean RA/DEC/ROLL : 191.7841 70.9742 232.0148
Pnt RA/DEC/ROLL : 191.9128 71.0025 232.0148
Image rebin factor : 1
Attitude Records : 59493
GTI intervals : 34
Total GTI (secs) : 22820.613
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2613.99 2613.99
20 Percent Complete: Total/live time: 4855.98 4855.98
30 Percent Complete: Total/live time: 7241.98 7241.98
40 Percent Complete: Total/live time: 10544.07 10544.07
50 Percent Complete: Total/live time: 11677.07 11677.07
60 Percent Complete: Total/live time: 14606.20 14606.20
70 Percent Complete: Total/live time: 17418.20 17418.20
80 Percent Complete: Total/live time: 19914.40 19914.40
90 Percent Complete: Total/live time: 20997.19 20997.19
100 Percent Complete: Total/live time: 22820.62 22820.62
Number of attitude steps used: 63
Number of attitude steps avail: 52461
Mean RA/DEC pixel offset: -13.1064 -3.0811
writing expo file: ad86046000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000g200170h.evt
ASCAEXPO_V0.9b
reading data file: ad86046000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0147
Mean RA/DEC/ROLL : 191.7854 70.9731 232.0147
Pnt RA/DEC/ROLL : 191.8982 71.0100 232.0147
Image rebin factor : 1
Attitude Records : 59493
GTI intervals : 8
Total GTI (secs) : 12655.717
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1651.98 1651.98
20 Percent Complete: Total/live time: 2975.92 2975.92
30 Percent Complete: Total/live time: 4007.91 4007.91
40 Percent Complete: Total/live time: 5463.75 5463.75
50 Percent Complete: Total/live time: 7867.74 7867.74
60 Percent Complete: Total/live time: 7867.74 7867.74
70 Percent Complete: Total/live time: 9223.73 9223.73
80 Percent Complete: Total/live time: 12143.91 12143.91
90 Percent Complete: Total/live time: 12143.91 12143.91
100 Percent Complete: Total/live time: 12655.72 12655.72
Number of attitude steps used: 46
Number of attitude steps avail: 7066
Mean RA/DEC pixel offset: -13.2276 -2.3283
writing expo file: ad86046000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000g200270m.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad86046000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0646
Mean RA/DEC/ROLL : 191.8368 70.9921 232.0646
Pnt RA/DEC/ROLL : 191.8602 70.9845 232.0646
Image rebin factor : 1
Attitude Records : 59493
GTI intervals : 34
Total GTI (secs) : 22814.613
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2611.99 2611.99
20 Percent Complete: Total/live time: 4853.98 4853.98
30 Percent Complete: Total/live time: 7237.98 7237.98
40 Percent Complete: Total/live time: 10538.07 10538.07
50 Percent Complete: Total/live time: 11671.07 11671.07
60 Percent Complete: Total/live time: 14600.20 14600.20
70 Percent Complete: Total/live time: 17412.20 17412.20
80 Percent Complete: Total/live time: 19908.40 19908.40
90 Percent Complete: Total/live time: 20991.19 20991.19
100 Percent Complete: Total/live time: 22814.62 22814.62
Number of attitude steps used: 63
Number of attitude steps avail: 52461
Mean RA/DEC pixel offset: -1.2195 -1.9003
writing expo file: ad86046000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000g300170h.evt
ASCAEXPO_V0.9b
reading data file: ad86046000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0645
Mean RA/DEC/ROLL : 191.8380 70.9911 232.0645
Pnt RA/DEC/ROLL : 191.8456 70.9920 232.0645
Image rebin factor : 1
Attitude Records : 59493
GTI intervals : 8
Total GTI (secs) : 12655.717
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1651.98 1651.98
20 Percent Complete: Total/live time: 2975.92 2975.92
30 Percent Complete: Total/live time: 4007.91 4007.91
40 Percent Complete: Total/live time: 5463.75 5463.75
50 Percent Complete: Total/live time: 7867.74 7867.74
60 Percent Complete: Total/live time: 7867.74 7867.74
70 Percent Complete: Total/live time: 9223.73 9223.73
80 Percent Complete: Total/live time: 12143.91 12143.91
90 Percent Complete: Total/live time: 12143.91 12143.91
100 Percent Complete: Total/live time: 12655.72 12655.72
Number of attitude steps used: 46
Number of attitude steps avail: 7066
Mean RA/DEC pixel offset: -1.4115 -1.1545
writing expo file: ad86046000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000g300270m.evt
ASCAEXPO_V0.9b
reading data file: ad86046000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0048
Mean RA/DEC/ROLL : 191.7742 70.9922 232.0048
Pnt RA/DEC/ROLL : 191.9229 70.9842 232.0048
Image rebin factor : 4
Attitude Records : 59493
Hot Pixels : 18
GTI intervals : 40
Total GTI (secs) : 19768.441
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2592.62 2592.62
20 Percent Complete: Total/live time: 4247.10 4247.10
30 Percent Complete: Total/live time: 6488.18 6488.18
40 Percent Complete: Total/live time: 9400.19 9400.19
50 Percent Complete: Total/live time: 10307.07 10307.07
60 Percent Complete: Total/live time: 12992.45 12992.45
70 Percent Complete: Total/live time: 15488.45 15488.45
80 Percent Complete: Total/live time: 17472.45 17472.45
90 Percent Complete: Total/live time: 18393.23 18393.23
100 Percent Complete: Total/live time: 19768.45 19768.45
Number of attitude steps used: 62
Number of attitude steps avail: 51864
Mean RA/DEC pixel offset: -65.4328 -92.4023
writing expo file: ad86046000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000s000102h.evt
ASCAEXPO_V0.9b
reading data file: ad86046000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0049
Mean RA/DEC/ROLL : 191.7760 70.9913 232.0049
Pnt RA/DEC/ROLL : 191.9077 70.9920 232.0049
Image rebin factor : 4
Attitude Records : 59493
Hot Pixels : 16
GTI intervals : 37
Total GTI (secs) : 10143.090
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1263.98 1263.98
20 Percent Complete: Total/live time: 2383.67 2383.67
30 Percent Complete: Total/live time: 3159.54 3159.54
40 Percent Complete: Total/live time: 4295.41 4295.41
50 Percent Complete: Total/live time: 5191.25 5191.25
60 Percent Complete: Total/live time: 7239.41 7239.41
70 Percent Complete: Total/live time: 7239.41 7239.41
80 Percent Complete: Total/live time: 9767.41 9767.41
90 Percent Complete: Total/live time: 9767.41 9767.41
100 Percent Complete: Total/live time: 10143.09 10143.09
Number of attitude steps used: 37
Number of attitude steps avail: 4865
Mean RA/DEC pixel offset: -66.7381 -84.3850
writing expo file: ad86046000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000s000202m.evt
ASCAEXPO_V0.9b
reading data file: ad86046000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0394
Mean RA/DEC/ROLL : 191.8108 70.9816 232.0394
Pnt RA/DEC/ROLL : 191.8864 70.9948 232.0394
Image rebin factor : 4
Attitude Records : 59493
Hot Pixels : 73
GTI intervals : 41
Total GTI (secs) : 19623.770
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2392.47 2392.47
20 Percent Complete: Total/live time: 4217.96 4217.96
30 Percent Complete: Total/live time: 6327.83 6327.83
40 Percent Complete: Total/live time: 9247.83 9247.83
50 Percent Complete: Total/live time: 10186.72 10186.72
60 Percent Complete: Total/live time: 12836.09 12836.09
70 Percent Complete: Total/live time: 15388.09 15388.09
80 Percent Complete: Total/live time: 17391.77 17391.77
90 Percent Complete: Total/live time: 18252.56 18252.56
100 Percent Complete: Total/live time: 19623.77 19623.77
Number of attitude steps used: 61
Number of attitude steps avail: 51815
Mean RA/DEC pixel offset: -69.6199 -22.1811
writing expo file: ad86046000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000s100102h.evt
ASCAEXPO_V0.9b
reading data file: ad86046000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa981203_1435.1120
making an exposure map...
Aspect RA/DEC/ROLL : 191.8530 70.9911 232.0394
Mean RA/DEC/ROLL : 191.8126 70.9807 232.0394
Pnt RA/DEC/ROLL : 191.8711 71.0025 232.0394
Image rebin factor : 4
Attitude Records : 59493
Hot Pixels : 52
GTI intervals : 84
Total GTI (secs) : 6543.557
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 911.97 911.97
20 Percent Complete: Total/live time: 1391.94 1391.94
30 Percent Complete: Total/live time: 2071.81 2071.81
40 Percent Complete: Total/live time: 2863.56 2863.56
50 Percent Complete: Total/live time: 3439.39 3439.39
60 Percent Complete: Total/live time: 4719.56 4719.56
70 Percent Complete: Total/live time: 4719.56 4719.56
80 Percent Complete: Total/live time: 6447.56 6447.56
90 Percent Complete: Total/live time: 6447.56 6447.56
100 Percent Complete: Total/live time: 6543.56 6543.56
Number of attitude steps used: 36
Number of attitude steps avail: 4568
Mean RA/DEC pixel offset: -70.8404 -14.6426
writing expo file: ad86046000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86046000s100202m.evtad86046000s000102h.expo ad86046000s000202m.expo ad86046000s100102h.expo ad86046000s100202m.expo-> Summing the following images to produce ad86046000sis32002_all.totsky
ad86046000s000102h.img ad86046000s000202m.img ad86046000s100102h.img ad86046000s100202m.img-> Summing the following images to produce ad86046000sis32002_lo.totsky
ad86046000s000102h_lo.img ad86046000s000202m_lo.img ad86046000s100102h_lo.img ad86046000s100202m_lo.img-> Summing the following images to produce ad86046000sis32002_hi.totsky
ad86046000s000102h_hi.img ad86046000s000202m_hi.img ad86046000s100102h_hi.img ad86046000s100202m_hi.img-> Running XIMAGE to create ad86046000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad86046000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 11.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 11 min: 0 ![2]XIMAGE> read/exp_map ad86046000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 934.648 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 934 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "MS1244.2+7114" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 December 3, 1998 Exposure: 56078.8 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 14225 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 14.0000 14 0 ![11]XIMAGE> exit-> Summing gis images
ad86046000g200170h.expo ad86046000g200270m.expo ad86046000g300170h.expo ad86046000g300270m.expo-> Summing the following images to produce ad86046000gis25670_all.totsky
ad86046000g200170h.img ad86046000g200270m.img ad86046000g300170h.img ad86046000g300270m.img-> Summing the following images to produce ad86046000gis25670_lo.totsky
ad86046000g200170h_lo.img ad86046000g200270m_lo.img ad86046000g300170h_lo.img ad86046000g300270m_lo.img-> Summing the following images to produce ad86046000gis25670_hi.totsky
ad86046000g200170h_hi.img ad86046000g200270m_hi.img ad86046000g300170h_hi.img ad86046000g300270m_hi.img-> Running XIMAGE to create ad86046000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad86046000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 17.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 17 min: 0 ![2]XIMAGE> read/exp_map ad86046000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1182.44 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1182 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "MS1244.2+7114" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 December 3, 1998 Exposure: 70946.6 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 38.0000 38 0 ![11]XIMAGE> exit
154 121 0.000162877 34 11 15.3999-> Smoothing ad86046000gis25670_hi.totsky with ad86046000gis25670.totexpo
154 121 8.30045e-05 29 10 14.3641-> Smoothing ad86046000gis25670_lo.totsky with ad86046000gis25670.totexpo
154 121 8.14383e-05 28 12 16.8351 191 70 1.80211e-05 27 11 4.16358-> Determining extraction radii
154 121 24 T 191 70 24 T-> Sources with radius >= 2
154 121 24 T 191 70 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad86046000gis25670.src
220 141 8.99371e-05 92 17 20.5651-> Smoothing ad86046000sis32002_hi.totsky with ad86046000sis32002.totexpo
219 139 2.54913e-05 94 19 10.6457-> Smoothing ad86046000sis32002_lo.totsky with ad86046000sis32002.totexpo
220 141 6.3527e-05 92 17 31.0606-> Determining extraction radii
220 141 38 T-> Sources with radius >= 2
220 141 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad86046000sis32002.src
The sum of the selected column is 175941.00 The mean of the selected column is 399.86591 The standard deviation of the selected column is 16.394836 The minimum of selected column is 361.00000 The maximum of selected column is 435.00000 The number of points used in calculation is 440-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 200483.00 The mean of the selected column is 455.64318 The standard deviation of the selected column is 18.124536 The minimum of selected column is 413.00000 The maximum of selected column is 501.00000 The number of points used in calculation is 440-> Converting (880.0,564.0,2.0) to s1 detector coordinates
The sum of the selected column is 133426.00 The mean of the selected column is 397.10119 The standard deviation of the selected column is 17.951058 The minimum of selected column is 357.00000 The maximum of selected column is 439.00000 The number of points used in calculation is 336-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 165686.00 The mean of the selected column is 493.11310 The standard deviation of the selected column is 18.217402 The minimum of selected column is 442.00000 The maximum of selected column is 532.00000 The number of points used in calculation is 336-> Converting (154.0,121.0,2.0) to g2 detector coordinates
The sum of the selected column is 5127.0000 The mean of the selected column is 100.52941 The standard deviation of the selected column is 1.1198739 The minimum of selected column is 99.000000 The maximum of selected column is 104.00000 The number of points used in calculation is 51-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5739.0000 The mean of the selected column is 112.52941 The standard deviation of the selected column is 1.1722276 The minimum of selected column is 110.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 51-> Converting (191.0,70.0,2.0) to g2 detector coordinates
The sum of the selected column is 12636.000 The mean of the selected column is 51.157895 The standard deviation of the selected column is 5.4013105 The minimum of selected column is 41.000000 The maximum of selected column is 62.000000 The number of points used in calculation is 247-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 28720.000 The mean of the selected column is 116.27530 The standard deviation of the selected column is 10.644912 The minimum of selected column is 94.000000 The maximum of selected column is 138.00000 The number of points used in calculation is 247-> Converting (154.0,121.0,2.0) to g3 detector coordinates
The sum of the selected column is 10649.000 The mean of the selected column is 106.49000 The standard deviation of the selected column is 1.0395706 The minimum of selected column is 104.00000 The maximum of selected column is 109.00000 The number of points used in calculation is 100-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 11317.000 The mean of the selected column is 113.17000 The standard deviation of the selected column is 1.1896439 The minimum of selected column is 111.00000 The maximum of selected column is 116.00000 The number of points used in calculation is 100-> Converting (191.0,70.0,2.0) to g3 detector coordinates
The sum of the selected column is 657.00000 The mean of the selected column is 43.800000 The standard deviation of the selected column is 1.2071217 The minimum of selected column is 42.000000 The maximum of selected column is 46.000000 The number of points used in calculation is 15-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1729.0000 The mean of the selected column is 115.26667 The standard deviation of the selected column is 1.0997835 The minimum of selected column is 113.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 15
1 ad86046000s000102h.evt 2987 1 ad86046000s000202m.evt 2987-> Fetching SIS0_NOTCHIP0.1
ad86046000s000102h.evt ad86046000s000202m.evt-> Grouping ad86046000s010102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 29912. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 18 are grouped by a factor 2 ... 19 - 22 are grouped by a factor 4 ... 23 - 25 are grouped by a factor 3 ... 26 - 31 are grouped by a factor 2 ... 32 - 32 are single channels ... 33 - 46 are grouped by a factor 2 ... 47 - 48 are single channels ... 49 - 58 are grouped by a factor 2 ... 59 - 70 are grouped by a factor 3 ... 71 - 74 are grouped by a factor 4 ... 75 - 79 are grouped by a factor 5 ... 80 - 85 are grouped by a factor 6 ... 86 - 93 are grouped by a factor 8 ... 94 - 111 are grouped by a factor 9 ... 112 - 121 are grouped by a factor 10 ... 122 - 133 are grouped by a factor 12 ... 134 - 147 are grouped by a factor 14 ... 148 - 174 are grouped by a factor 27 ... 175 - 198 are grouped by a factor 24 ... 199 - 298 are grouped by a factor 100 ... 299 - 511 are grouped by a factor 213 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000s010102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad86046000s010102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 38 by 38 bins
expanded to 38 by 38 bins
First WMAP bin is at detector pixel 248 304
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 3.3063 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.00200E+03
Weighted mean angle from optical axis = 7.542 arcmin
-> Standard Output From STOOL group_event_files:1 ad86046000s000112h.evt 3114 1 ad86046000s000212m.evt 3114-> SIS0_NOTCHIP0.1 already present in current directory
ad86046000s000112h.evt ad86046000s000212m.evt-> Grouping ad86046000s010212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 29912. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 35 are grouped by a factor 4 ... 36 - 42 are grouped by a factor 7 ... 43 - 48 are grouped by a factor 6 ... 49 - 56 are grouped by a factor 4 ... 57 - 59 are grouped by a factor 3 ... 60 - 63 are grouped by a factor 2 ... 64 - 93 are grouped by a factor 3 ... 94 - 97 are grouped by a factor 2 ... 98 - 103 are grouped by a factor 3 ... 104 - 111 are grouped by a factor 4 ... 112 - 114 are grouped by a factor 3 ... 115 - 129 are grouped by a factor 5 ... 130 - 147 are grouped by a factor 6 ... 148 - 156 are grouped by a factor 9 ... 157 - 168 are grouped by a factor 12 ... 169 - 181 are grouped by a factor 13 ... 182 - 198 are grouped by a factor 17 ... 199 - 214 are grouped by a factor 16 ... 215 - 256 are grouped by a factor 21 ... 257 - 282 are grouped by a factor 26 ... 283 - 326 are grouped by a factor 44 ... 327 - 375 are grouped by a factor 49 ... 376 - 472 are grouped by a factor 97 ... 473 - 749 are grouped by a factor 277 ... 750 - 1000 are grouped by a factor 251 ... 1001 - 1023 are grouped by a factor 23 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000s010212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad86046000s010212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 38 by 38 bins
expanded to 38 by 38 bins
First WMAP bin is at detector pixel 248 304
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 3.3063 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.05600E+03
Weighted mean angle from optical axis = 7.540 arcmin
-> Standard Output From STOOL group_event_files:1 ad86046000s100102h.evt 2422 1 ad86046000s100202m.evt 2422-> Fetching SIS1_NOTCHIP0.1
ad86046000s100102h.evt ad86046000s100202m.evt-> Grouping ad86046000s110102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 26167. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.41895E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 20 are grouped by a factor 4 ... 21 - 26 are grouped by a factor 3 ... 27 - 30 are grouped by a factor 2 ... 31 - 33 are grouped by a factor 3 ... 34 - 49 are grouped by a factor 2 ... 50 - 64 are grouped by a factor 3 ... 65 - 68 are grouped by a factor 4 ... 69 - 73 are grouped by a factor 5 ... 74 - 79 are grouped by a factor 6 ... 80 - 89 are grouped by a factor 10 ... 90 - 111 are grouped by a factor 11 ... 112 - 131 are grouped by a factor 20 ... 132 - 148 are grouped by a factor 17 ... 149 - 173 are grouped by a factor 25 ... 174 - 220 are grouped by a factor 47 ... 221 - 271 are grouped by a factor 51 ... 272 - 417 are grouped by a factor 146 ... 418 - 472 are grouped by a factor 55 ... 473 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000s110102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad86046000s110102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 38 by 36 bins
expanded to 38 by 36 bins
First WMAP bin is at detector pixel 248 344
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 3.1825 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.53800E+03
Weighted mean angle from optical axis = 9.250 arcmin
-> Standard Output From STOOL group_event_files:1 ad86046000s100112h.evt 2505 1 ad86046000s100212m.evt 2505-> SIS1_NOTCHIP0.1 already present in current directory
ad86046000s100112h.evt ad86046000s100212m.evt-> Grouping ad86046000s110212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 26167. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.41895E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 40 are grouped by a factor 8 ... 41 - 47 are grouped by a factor 7 ... 48 - 53 are grouped by a factor 6 ... 54 - 61 are grouped by a factor 4 ... 62 - 66 are grouped by a factor 5 ... 67 - 72 are grouped by a factor 3 ... 73 - 80 are grouped by a factor 4 ... 81 - 86 are grouped by a factor 3 ... 87 - 106 are grouped by a factor 4 ... 107 - 121 are grouped by a factor 5 ... 122 - 133 are grouped by a factor 6 ... 134 - 142 are grouped by a factor 9 ... 143 - 152 are grouped by a factor 10 ... 153 - 169 are grouped by a factor 17 ... 170 - 190 are grouped by a factor 21 ... 191 - 209 are grouped by a factor 19 ... 210 - 238 are grouped by a factor 29 ... 239 - 268 are grouped by a factor 30 ... 269 - 310 are grouped by a factor 42 ... 311 - 361 are grouped by a factor 51 ... 362 - 451 are grouped by a factor 90 ... 452 - 560 are grouped by a factor 109 ... 561 - 828 are grouped by a factor 268 ... 829 - 931 are grouped by a factor 103 ... 932 - 1023 are grouped by a factor 92 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000s110212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad86046000s110212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 38 by 36 bins
expanded to 38 by 36 bins
First WMAP bin is at detector pixel 248 344
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 3.1825 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.57000E+03
Weighted mean angle from optical axis = 9.258 arcmin
-> Standard Output From STOOL group_event_files:1 ad86046000g200170h.evt 10182 1 ad86046000g200270m.evt 10182-> GIS2_REGION256.4 already present in current directory
ad86046000g200170h.evt ad86046000g200270m.evt-> Correcting ad86046000g210170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86046000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 35476. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 44 are grouped by a factor 45 ... 45 - 63 are grouped by a factor 19 ... 64 - 73 are grouped by a factor 10 ... 74 - 82 are grouped by a factor 9 ... 83 - 96 are grouped by a factor 7 ... 97 - 114 are grouped by a factor 6 ... 115 - 119 are grouped by a factor 5 ... 120 - 123 are grouped by a factor 4 ... 124 - 159 are grouped by a factor 6 ... 160 - 169 are grouped by a factor 5 ... 170 - 175 are grouped by a factor 6 ... 176 - 182 are grouped by a factor 7 ... 183 - 215 are grouped by a factor 11 ... 216 - 233 are grouped by a factor 18 ... 234 - 285 are grouped by a factor 26 ... 286 - 302 are grouped by a factor 17 ... 303 - 335 are grouped by a factor 33 ... 336 - 366 are grouped by a factor 31 ... 367 - 394 are grouped by a factor 28 ... 395 - 427 are grouped by a factor 33 ... 428 - 478 are grouped by a factor 51 ... 479 - 537 are grouped by a factor 59 ... 538 - 625 are grouped by a factor 88 ... 626 - 780 are grouped by a factor 155 ... 781 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000g210170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 48 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 38 50
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.56500E+03
Weighted mean angle from optical axis = 9.365 arcmin
-> Extracting ad86046000g210170_2.pi from ad86046000g225670_2.reg and:ad86046000g200170h.evt ad86046000g200270m.evt-> Correcting ad86046000g210170_2.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86046000g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 35476. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.10419E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 35 are grouped by a factor 36 ... 36 - 74 are grouped by a factor 39 ... 75 - 99 are grouped by a factor 25 ... 100 - 143 are grouped by a factor 22 ... 144 - 175 are grouped by a factor 32 ... 176 - 233 are grouped by a factor 58 ... 234 - 299 are grouped by a factor 66 ... 300 - 390 are grouped by a factor 91 ... 391 - 480 are grouped by a factor 90 ... 481 - 648 are grouped by a factor 168 ... 649 - 795 are grouped by a factor 147 ... 796 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000g210170_2.pi ** grppha 2.8.1 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 34 by 48 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 27 53
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 83.167 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.16000E+02
Weighted mean angle from optical axis = 19.220 arcmin
-> Standard Output From STOOL group_event_files:1 ad86046000g300170h.evt 11179 1 ad86046000g300270m.evt 11179-> GIS3_REGION256.4 already present in current directory
ad86046000g300170h.evt ad86046000g300270m.evt-> Correcting ad86046000g310170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86046000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 35470. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 37 are grouped by a factor 38 ... 38 - 54 are grouped by a factor 17 ... 55 - 65 are grouped by a factor 11 ... 66 - 79 are grouped by a factor 7 ... 80 - 99 are grouped by a factor 5 ... 100 - 103 are grouped by a factor 4 ... 104 - 118 are grouped by a factor 5 ... 119 - 122 are grouped by a factor 4 ... 123 - 128 are grouped by a factor 6 ... 129 - 132 are grouped by a factor 4 ... 133 - 142 are grouped by a factor 5 ... 143 - 150 are grouped by a factor 4 ... 151 - 168 are grouped by a factor 6 ... 169 - 188 are grouped by a factor 5 ... 189 - 208 are grouped by a factor 10 ... 209 - 244 are grouped by a factor 12 ... 245 - 270 are grouped by a factor 13 ... 271 - 285 are grouped by a factor 15 ... 286 - 302 are grouped by a factor 17 ... 303 - 322 are grouped by a factor 20 ... 323 - 350 are grouped by a factor 28 ... 351 - 380 are grouped by a factor 30 ... 381 - 414 are grouped by a factor 34 ... 415 - 439 are grouped by a factor 25 ... 440 - 466 are grouped by a factor 27 ... 467 - 519 are grouped by a factor 53 ... 520 - 565 are grouped by a factor 46 ... 566 - 656 are grouped by a factor 91 ... 657 - 803 are grouped by a factor 147 ... 804 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000g310170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 48 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 43 50
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.99300E+03
Weighted mean angle from optical axis = 6.621 arcmin
-> Extracting ad86046000g310170_2.pi from ad86046000g325670_2.reg and:ad86046000g300170h.evt ad86046000g300270m.evt-> Correcting ad86046000g310170_2.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86046000g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 35470. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.57928E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 26 are grouped by a factor 27 ... 27 - 33 are grouped by a factor 7 ... 34 - 52 are grouped by a factor 19 ... 53 - 76 are grouped by a factor 24 ... 77 - 102 are grouped by a factor 26 ... 103 - 127 are grouped by a factor 25 ... 128 - 166 are grouped by a factor 39 ... 167 - 212 are grouped by a factor 46 ... 213 - 282 are grouped by a factor 70 ... 283 - 369 are grouped by a factor 87 ... 370 - 486 are grouped by a factor 117 ... 487 - 659 are grouped by a factor 173 ... 660 - 929 are grouped by a factor 270 ... 930 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86046000g310170_2.pi ** grppha 2.8.1 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 27 by 48 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 24 52
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 62.420 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.32000E+02
Weighted mean angle from optical axis = 17.380 arcmin
-> Plotting ad86046000g210170_1_pi.ps from ad86046000g210170_1.pi
XSPEC 9.01 10:14:46 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000g210170_1.pi
Net count rate (cts/s) for file 1 4.4311E-02+/- 1.1889E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000g210170_2_pi.ps from ad86046000g210170_2.pi
XSPEC 9.01 10:15:07 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000g210170_2.pi
Net count rate (cts/s) for file 1 1.4770E-02+/- 7.5688E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000g310170_1_pi.ps from ad86046000g310170_1.pi
XSPEC 9.01 10:15:27 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000g310170_1.pi
Net count rate (cts/s) for file 1 5.6442E-02+/- 1.3223E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000g310170_2_pi.ps from ad86046000g310170_2.pi
XSPEC 9.01 10:15:47 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000g310170_2.pi
Net count rate (cts/s) for file 1 1.5196E-02+/- 7.0199E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000s010102_1_pi.ps from ad86046000s010102_1.pi
XSPEC 9.01 10:16:06 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000s010102_1.pi
Net count rate (cts/s) for file 1 6.7499E-02+/- 1.5074E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000s010212_1_pi.ps from ad86046000s010212_1.pi
XSPEC 9.01 10:16:29 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000s010212_1.pi
Net count rate (cts/s) for file 1 6.9338E-02+/- 1.5328E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000s110102_1_pi.ps from ad86046000s110102_1.pi
XSPEC 9.01 10:16:53 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000s110102_1.pi
Net count rate (cts/s) for file 1 5.9502E-02+/- 1.5305E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86046000s110212_1_pi.ps from ad86046000s110212_1.pi
XSPEC 9.01 10:17:14 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86046000s110212_1.pi
Net count rate (cts/s) for file 1 6.0725E-02+/- 1.5372E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:13:12.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:11:04.007
No. of Rows ....... 41 Bin Time (s) ...... 740.8
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA SIS0
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 98 Newbins of 740.751 (s)
Intv 1 Start11150 15:19:22
Ser.1 Avg 0.6732E-01 Chisq 46.53 Var 0.1206E-03 Newbs. 41
Min 0.4233E-01 Max 0.9105E-01expVar 0.1063E-03 Bins 41
Results from Statistical Analysis
Newbin Integration Time (s).. 740.75
Interval Duration (s)........ 71112.
No. of Newbins .............. 41
Average (c/s) ............... 0.67316E-01 +/- 0.16E-02
Standard Deviation (c/s)..... 0.10984E-01
Minimum (c/s)................ 0.42328E-01
Maximum (c/s)................ 0.91050E-01
Variance ((c/s)**2).......... 0.12065E-03 +/- 0.27E-04
Expected Variance ((c/s)**2). 0.10631E-03 +/- 0.24E-04
Third Moment ((c/s)**3)...... 0.14697E-06
Average Deviation (c/s)...... 0.87990E-02
Skewness..................... 0.11091 +/- 0.38
Kurtosis.....................-0.49659 +/- 0.77
RMS fractional variation....< 0.12534 (3 sigma)
Chi-Square................... 46.531 dof 40
Chi-Square Prob of constancy. 0.22143 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.34098 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 98 Newbins of 740.751 (s)
Intv 1 Start11150 15:19:22
Ser.1 Avg 0.6732E-01 Chisq 46.53 Var 0.1206E-03 Newbs. 41
Min 0.4233E-01 Max 0.9105E-01expVar 0.1063E-03 Bins 41
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000s000002_1.lc
PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad86046000s100102h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:13:12.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:11:04.007
No. of Rows ....... 33 Bin Time (s) ...... 838.7
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA SIS1
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 86 Newbins of 838.696 (s)
Intv 1 Start11150 15:20:11
Ser.1 Avg 0.5901E-01 Chisq 31.07 Var 0.8453E-04 Newbs. 33
Min 0.3987E-01 Max 0.7758E-01expVar 0.8979E-04 Bins 33
Results from Statistical Analysis
Newbin Integration Time (s).. 838.70
Interval Duration (s)........ 71289.
No. of Newbins .............. 33
Average (c/s) ............... 0.59009E-01 +/- 0.17E-02
Standard Deviation (c/s)..... 0.91942E-02
Minimum (c/s)................ 0.39874E-01
Maximum (c/s)................ 0.77580E-01
Variance ((c/s)**2).......... 0.84534E-04 +/- 0.21E-04
Expected Variance ((c/s)**2). 0.89792E-04 +/- 0.22E-04
Third Moment ((c/s)**3)...... 0.23893E-06
Average Deviation (c/s)...... 0.71786E-02
Skewness..................... 0.30741 +/- 0.43
Kurtosis.....................-0.35774 +/- 0.85
RMS fractional variation....< 0.15869 (3 sigma)
Chi-Square................... 31.068 dof 32
Chi-Square Prob of constancy. 0.51351 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.23190 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 86 Newbins of 838.696 (s)
Intv 1 Start11150 15:20:11
Ser.1 Avg 0.5901E-01 Chisq 31.07 Var 0.8453E-04 Newbs. 33
Min 0.3987E-01 Max 0.7758E-01expVar 0.8979E-04 Bins 33
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000s100002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad86046000g200170h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:11:04.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:16:24.007
No. of Rows ....... 31 Bin Time (s) ...... 1128.
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 65 Newbins of 1128.38 (s)
Intv 1 Start11150 15:20:28
Ser.1 Avg 0.4547E-01 Chisq 19.94 Var 0.3068E-04 Newbs. 31
Min 0.3456E-01 Max 0.6085E-01expVar 0.4770E-04 Bins 31
Results from Statistical Analysis
Newbin Integration Time (s).. 1128.4
Interval Duration (s)........ 71088.
No. of Newbins .............. 31
Average (c/s) ............... 0.45470E-01 +/- 0.13E-02
Standard Deviation (c/s)..... 0.55388E-02
Minimum (c/s)................ 0.34563E-01
Maximum (c/s)................ 0.60847E-01
Variance ((c/s)**2).......... 0.30679E-04 +/- 0.79E-05
Expected Variance ((c/s)**2). 0.47699E-04 +/- 0.12E-04
Third Moment ((c/s)**3)...... 0.10473E-06
Average Deviation (c/s)...... 0.41774E-02
Skewness..................... 0.61630 +/- 0.44
Kurtosis..................... 0.68646 +/- 0.88
RMS fractional variation....< 0.17394 (3 sigma)
Chi-Square................... 19.938 dof 30
Chi-Square Prob of constancy. 0.91812 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.13573 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 65 Newbins of 1128.38 (s)
Intv 1 Start11150 15:20:28
Ser.1 Avg 0.4547E-01 Chisq 19.94 Var 0.3068E-04 Newbs. 31
Min 0.3456E-01 Max 0.6085E-01expVar 0.4770E-04 Bins 31
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000g200070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Extracting events from region ad86046000g225670_2.reg
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:11:04.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:16:24.007
No. of Rows ....... 10 Bin Time (s) ...... 3385.
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 22 Newbins of 3385.15 (s)
Intv 1 Start11150 15:39:16
Ser.1 Avg 0.1493E-01 Chisq 6.805 Var 0.4284E-05 Newbs. 10
Min 0.1176E-01 Max 0.1902E-01expVar 0.6296E-05 Bins 10
Results from Statistical Analysis
Newbin Integration Time (s).. 3385.1
Interval Duration (s)........ 64318.
No. of Newbins .............. 10
Average (c/s) ............... 0.14927E-01 +/- 0.84E-03
Standard Deviation (c/s)..... 0.20697E-02
Minimum (c/s)................ 0.11759E-01
Maximum (c/s)................ 0.19023E-01
Variance ((c/s)**2).......... 0.42839E-05 +/- 0.20E-05
Expected Variance ((c/s)**2). 0.62956E-05 +/- 0.30E-05
Third Moment ((c/s)**3)...... 0.22229E-08
Average Deviation (c/s)...... 0.16847E-02
Skewness..................... 0.25071 +/- 0.77
Kurtosis.....................-0.46395 +/- 1.5
RMS fractional variation....< 0.25671 (3 sigma)
Chi-Square................... 6.8045 dof 9
Chi-Square Prob of constancy. 0.65742 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.33737 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 22 Newbins of 3385.15 (s)
Intv 1 Start11150 15:39:16
Ser.1 Avg 0.1493E-01 Chisq 6.805 Var 0.4284E-05 Newbs. 10
Min 0.1176E-01 Max 0.1902E-01expVar 0.6296E-05 Bins 10
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000g200070_2.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad86046000g300170h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:11:04.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:16:24.007
No. of Rows ....... 42 Bin Time (s) ...... 885.9
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 82 Newbins of 885.872 (s)
Intv 1 Start11150 15:18:26
Ser.1 Avg 0.5601E-01 Chisq 31.54 Var 0.5746E-04 Newbs. 42
Min 0.4276E-01 Max 0.7180E-01expVar 0.7652E-04 Bins 42
Results from Statistical Analysis
Newbin Integration Time (s).. 885.87
Interval Duration (s)........ 71756.
No. of Newbins .............. 42
Average (c/s) ............... 0.56011E-01 +/- 0.14E-02
Standard Deviation (c/s)..... 0.75800E-02
Minimum (c/s)................ 0.42762E-01
Maximum (c/s)................ 0.71802E-01
Variance ((c/s)**2).......... 0.57457E-04 +/- 0.13E-04
Expected Variance ((c/s)**2). 0.76519E-04 +/- 0.17E-04
Third Moment ((c/s)**3)...... 0.43993E-07
Average Deviation (c/s)...... 0.63036E-02
Skewness..................... 0.10101 +/- 0.38
Kurtosis.....................-0.79395 +/- 0.76
RMS fractional variation....< 0.15955 (3 sigma)
Chi-Square................... 31.537 dof 41
Chi-Square Prob of constancy. 0.85612 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.30978 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 82 Newbins of 885.872 (s)
Intv 1 Start11150 15:18:26
Ser.1 Avg 0.5601E-01 Chisq 31.54 Var 0.5746E-04 Newbs. 42
Min 0.4276E-01 Max 0.7180E-01expVar 0.7652E-04 Bins 42
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000g300070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Extracting events from region ad86046000g325670_2.reg
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86046000g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ MS1244.2+7114 Start Time (d) .... 11150 15:11:04.007
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11151 11:16:24.007
No. of Rows ....... 10 Bin Time (s) ...... 3290.
Right Ascension ... 1.9185E+02 Internal time sys.. Converted to TJD
Declination ....... 7.0991E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 22 Newbins of 3290.38 (s)
Intv 1 Start11150 15:38:29
Ser.1 Avg 0.1455E-01 Chisq 7.628 Var 0.4639E-05 Newbs. 10
Min 0.1182E-01 Max 0.1819E-01expVar 0.6082E-05 Bins 10
Results from Statistical Analysis
Newbin Integration Time (s).. 3290.4
Interval Duration (s)........ 69098.
No. of Newbins .............. 10
Average (c/s) ............... 0.14545E-01 +/- 0.82E-03
Standard Deviation (c/s)..... 0.21539E-02
Minimum (c/s)................ 0.11824E-01
Maximum (c/s)................ 0.18192E-01
Variance ((c/s)**2).......... 0.46393E-05 +/- 0.22E-05
Expected Variance ((c/s)**2). 0.60817E-05 +/- 0.29E-05
Third Moment ((c/s)**3)...... 0.23511E-08
Average Deviation (c/s)...... 0.18352E-02
Skewness..................... 0.23529 +/- 0.77
Kurtosis..................... -1.1577 +/- 1.5
RMS fractional variation....< 0.25430 (3 sigma)
Chi-Square................... 7.6283 dof 9
Chi-Square Prob of constancy. 0.57193 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.29242 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 22 Newbins of 3290.38 (s)
Intv 1 Start11150 15:38:29
Ser.1 Avg 0.1455E-01 Chisq 7.628 Var 0.4639E-05 Newbs. 10
Min 0.1182E-01 Max 0.1819E-01expVar 0.6082E-05 Bins 10
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86046000g300070_2.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad86046000g200170h.evt[2] ad86046000g200270m.evt[2]-> Making L1 light curve of ft981203_1435_1120G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 41939 output records from 41973 good input G2_L1 records.-> Making L1 light curve of ft981203_1435_1120G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 30907 output records from 52994 good input G2_L1 records.-> Merging GTIs from the following files:
ad86046000g300170h.evt[2] ad86046000g300270m.evt[2]-> Making L1 light curve of ft981203_1435_1120G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 38837 output records from 38871 good input G3_L1 records.-> Making L1 light curve of ft981203_1435_1120G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 30133 output records from 49644 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 14884 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft981203_1435_1120.mkf
1 ad86046000g200170h.unf 58286 1 ad86046000g200270m.unf 58286 1 ad86046000g200370l.unf 58286 1 ad86046000g200470l.unf 58286-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 10:50:37 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad86046000g220170.cal
Net count rate (cts/s) for file 1 0.1325 +/- 1.6128E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.8798E+06 using 84 PHA bins.
Reduced chi-squared = 3.7400E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.8619E+06 using 84 PHA bins.
Reduced chi-squared = 3.6691E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.8619E+06 using 84 PHA bins.
Reduced chi-squared = 3.6227E+04
!XSPEC> renorm
Chi-Squared = 1245. using 84 PHA bins.
Reduced chi-squared = 15.76
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1002.3 0 1.000 5.895 0.1018 3.4373E-02
3.1640E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
642.42 0 1.000 5.884 0.1512 4.4269E-02
2.8633E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
373.59 -1 1.000 5.952 0.1776 5.9634E-02
2.0338E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
285.09 -2 1.000 6.036 0.2153 7.3844E-02
1.0792E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
278.22 -3 1.000 6.009 0.1925 7.0465E-02
1.4055E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
277.04 -4 1.000 6.020 0.2003 7.2209E-02
1.2288E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
276.58 -5 1.000 6.015 0.1958 7.1440E-02
1.3039E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
276.56 -1 1.000 6.016 0.1969 7.1652E-02
1.2821E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
276.56 3 1.000 6.016 0.1969 7.1652E-02
1.2821E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 6.01643 +/- 0.84699E-02
3 3 2 gaussian/b Sigma 0.196850 +/- 0.85744E-02
4 4 2 gaussian/b norm 7.165181E-02 +/- 0.15718E-02
5 2 3 gaussian/b LineE 6.62412 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.206553 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.282059E-02 +/- 0.11310E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 276.6 using 84 PHA bins.
Reduced chi-squared = 3.501
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad86046000g220170.cal peaks at 6.01643 +/- 0.0084699 keV1 ad86046000g300170h.unf 56381 1 ad86046000g300270m.unf 56381 1 ad86046000g300370l.unf 56381 1 ad86046000g300470l.unf 56381-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 10:51:58 26-Nov-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad86046000g320170.cal
Net count rate (cts/s) for file 1 0.1138 +/- 1.4949E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 3.9361E+06 using 84 PHA bins.
Reduced chi-squared = 5.1119E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 3.9067E+06 using 84 PHA bins.
Reduced chi-squared = 5.0085E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 3.9067E+06 using 84 PHA bins.
Reduced chi-squared = 4.9451E+04
!XSPEC> renorm
Chi-Squared = 1733. using 84 PHA bins.
Reduced chi-squared = 21.93
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1396.2 0 1.000 5.892 9.1017E-02 2.7601E-02
2.3369E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
490.51 0 1.000 5.859 0.1396 4.5280E-02
2.0055E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
172.95 -1 1.000 5.894 0.1503 6.4956E-02
1.3307E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
160.55 -2 1.000 5.910 0.1577 6.9386E-02
1.0830E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
160.28 -3 1.000 5.907 0.1548 6.9102E-02
1.1123E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
160.28 -4 1.000 5.908 0.1550 6.9151E-02
1.1075E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.90762 +/- 0.66350E-02
3 3 2 gaussian/b Sigma 0.154973 +/- 0.80403E-02
4 4 2 gaussian/b norm 6.915141E-02 +/- 0.13945E-02
5 2 3 gaussian/b LineE 6.50432 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.162611 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.107475E-02 +/- 0.87664E-03
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 160.3 using 84 PHA bins.
Reduced chi-squared = 2.029
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad86046000g320170.cal peaks at 5.90762 +/- 0.006635 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 293
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 140
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 293
Number of image cts rejected (N, %) : 14047.78
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 293 0 0
Image cts rejected: 0 140 0 0
Image cts rej (%) : 0.00 47.78 0.00 0.00
filtering data...
Total counts : 0 293 0 0
Total cts rejected: 0 140 0 0
Total cts rej (%) : 0.00 47.78 0.00 0.00
Number of clean counts accepted : 153
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 294
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 140
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 294
Number of image cts rejected (N, %) : 14047.62
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 294 0 0
Image cts rejected: 0 140 0 0
Image cts rej (%) : 0.00 47.62 0.00 0.00
filtering data...
Total counts : 0 294 0 0
Total cts rejected: 0 140 0 0
Total cts rej (%) : 0.00 47.62 0.00 0.00
Number of clean counts accepted : 154
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1819
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 1683
Flickering pixels iter, pixels & cnts : 1 5 32
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 15
Number of (internal) image counts : 1819
Number of image cts rejected (N, %) : 171594.28
By chip : 0 1 2 3
Pixels rejected : 0 15 0 0
Image counts : 0 1819 0 0
Image cts rejected: 0 1715 0 0
Image cts rej (%) : 0.00 94.28 0.00 0.00
filtering data...
Total counts : 0 1819 0 0
Total cts rejected: 0 1715 0 0
Total cts rej (%) : 0.00 94.28 0.00 0.00
Number of clean counts accepted : 104
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 15
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1832
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 1683
Flickering pixels iter, pixels & cnts : 1 5 32
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 15
Number of (internal) image counts : 1832
Number of image cts rejected (N, %) : 171593.61
By chip : 0 1 2 3
Pixels rejected : 0 15 0 0
Image counts : 0 1832 0 0
Image cts rejected: 0 1715 0 0
Image cts rej (%) : 0.00 93.61 0.00 0.00
filtering data...
Total counts : 0 1832 0 0
Total cts rejected: 0 1715 0 0
Total cts rej (%) : 0.00 93.61 0.00 0.00
Number of clean counts accepted : 117
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 15
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6216
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 5684
Flickering pixels iter, pixels & cnts : 1 7 48
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 17
Number of (internal) image counts : 6216
Number of image cts rejected (N, %) : 573292.21
By chip : 0 1 2 3
Pixels rejected : 0 17 0 0
Image counts : 0 6216 0 0
Image cts rejected: 0 5732 0 0
Image cts rej (%) : 0.00 92.21 0.00 0.00
filtering data...
Total counts : 0 6216 0 0
Total cts rejected: 0 5732 0 0
Total cts rej (%) : 0.00 92.21 0.00 0.00
Number of clean counts accepted : 484
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 17
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 6281
Total counts in chip images : 6280
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 5683
Flickering pixels iter, pixels & cnts : 1 7 48
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 17
Number of (internal) image counts : 6280
Number of image cts rejected (N, %) : 573191.26
By chip : 0 1 2 3
Pixels rejected : 0 17 0 0
Image counts : 0 6280 0 0
Image cts rejected: 0 5731 0 0
Image cts rej (%) : 0.00 91.26 0.00 0.00
filtering data...
Total counts : 0 6281 0 0
Total cts rejected: 0 5732 0 0
Total cts rej (%) : 0.00 91.26 0.00 0.00
Number of clean counts accepted : 549
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 17
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 498
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 18 448
Flickering pixels iter, pixels & cnts : 1 5 20
Number of pixels rejected : 23
Number of (internal) image counts : 498
Number of image cts rejected (N, %) : 46893.98
By chip : 0 1 2 3
Pixels rejected : 0 0 0 23
Image counts : 0 0 0 498
Image cts rejected: 0 0 0 468
Image cts rej (%) : 0.00 0.00 0.00 93.98
filtering data...
Total counts : 0 0 0 498
Total cts rejected: 0 0 0 468
Total cts rej (%) : 0.00 0.00 0.00 93.98
Number of clean counts accepted : 30
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 23
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 499
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 18 448
Flickering pixels iter, pixels & cnts : 1 5 20
Number of pixels rejected : 23
Number of (internal) image counts : 499
Number of image cts rejected (N, %) : 46893.79
By chip : 0 1 2 3
Pixels rejected : 0 0 0 23
Image counts : 0 0 0 499
Image cts rejected: 0 0 0 468
Image cts rej (%) : 0.00 0.00 0.00 93.79
filtering data...
Total counts : 0 0 0 499
Total cts rejected: 0 0 0 468
Total cts rej (%) : 0.00 0.00 0.00 93.79
Number of clean counts accepted : 31
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 23
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4962
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 32 4669
Flickering pixels iter, pixels & cnts : 1 17 166
Number of pixels rejected : 49
Number of (internal) image counts : 4962
Number of image cts rejected (N, %) : 483597.44
By chip : 0 1 2 3
Pixels rejected : 0 0 0 49
Image counts : 0 0 0 4962
Image cts rejected: 0 0 0 4835
Image cts rej (%) : 0.00 0.00 0.00 97.44
filtering data...
Total counts : 0 0 0 4962
Total cts rejected: 0 0 0 4835
Total cts rej (%) : 0.00 0.00 0.00 97.44
Number of clean counts accepted : 127
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 49
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4974
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 32 4669
Flickering pixels iter, pixels & cnts : 1 17 166
Number of pixels rejected : 49
Number of (internal) image counts : 4974
Number of image cts rejected (N, %) : 483597.21
By chip : 0 1 2 3
Pixels rejected : 0 0 0 49
Image counts : 0 0 0 4974
Image cts rejected: 0 0 0 4835
Image cts rej (%) : 0.00 0.00 0.00 97.21
filtering data...
Total counts : 0 0 0 4974
Total cts rejected: 0 0 0 4835
Total cts rej (%) : 0.00 0.00 0.00 97.21
Number of clean counts accepted : 139
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 49
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8616
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 21 8245
Flickering pixels iter, pixels & cnts : 1 11 120
Number of pixels rejected : 32
Number of (internal) image counts : 8616
Number of image cts rejected (N, %) : 836597.09
By chip : 0 1 2 3
Pixels rejected : 0 0 0 32
Image counts : 0 0 0 8616
Image cts rejected: 0 0 0 8365
Image cts rej (%) : 0.00 0.00 0.00 97.09
filtering data...
Total counts : 0 0 0 8616
Total cts rejected: 0 0 0 8365
Total cts rej (%) : 0.00 0.00 0.00 97.09
Number of clean counts accepted : 251
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86046000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8642
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 21 8245
Flickering pixels iter, pixels & cnts : 1 11 120
Number of pixels rejected : 32
Number of (internal) image counts : 8642
Number of image cts rejected (N, %) : 836596.79
By chip : 0 1 2 3
Pixels rejected : 0 0 0 32
Image counts : 0 0 0 8642
Image cts rejected: 0 0 0 8365
Image cts rej (%) : 0.00 0.00 0.00 96.79
filtering data...
Total counts : 0 0 0 8642
Total cts rejected: 0 0 0 8365
Total cts rej (%) : 0.00 0.00 0.00 96.79
Number of clean counts accepted : 277
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86046000g200170h.unfOffset of 208224004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-08-08 00:00:00.00000 Modified Julian Day = 51398.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
ad86046000g200370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad86046000g200470l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad86046000g200370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad86046000g200470l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad86046000g200370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad86046000g200470l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad86046000g200370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad86046000g200470l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad86046000g200370l.unf|SP_A_U_F|239|Spread discri A_U for FLF method (0-255) ad86046000g200470l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad86046000g200370l.unf|SP_B_F|226|Spread discri B for FLF method (0-255) ad86046000g200470l.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad86046000g200370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad86046000g200470l.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad86046000g200370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad86046000g200470l.unf|SP_PH_F|31098|Spread discri PH for FLF method (0-1023)-> listing ad86046000g200370l.unf
ad86046000g300370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad86046000g300470l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad86046000g300370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad86046000g300470l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad86046000g300370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad86046000g300470l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad86046000g300370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad86046000g300470l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad86046000g300370l.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255) ad86046000g300470l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad86046000g300370l.unf|SP_B_F|224|Spread discri B for FLF method (0-255) ad86046000g300470l.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad86046000g300370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad86046000g300470l.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad86046000g300370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad86046000g300470l.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)-> listing ad86046000g300370l.unf
1039 8656 1134 106 3426 100 5740 96 8074 94 8353 356 10099 612 12054 610 13978 610 11
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files