The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 175149757.186900 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-07-21 04:42:33.18689 Modified Julian Day = 51015.196217440970941-> leapsec.fits already present in current directory
Offset of 175204829.018300 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1998-07-21 20:00:25.01830 Modified Julian Day = 51015.833622896992892-> Observation begins 175149757.1869 1998-07-21 04:42:33
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 175149761.186700 175204829.018300
Data file start and stop ascatime : 175149761.186700 175204829.018300
Aspecting run start and stop ascatime : 175149761.186819 175204829.018202
Time interval averaged over (seconds) : 55067.831384
Total pointing and manuver time (sec) : 38007.964844 17059.986328
Mean boresight Euler angles : 247.864942 50.508047 136.901033
RA DEC SUN ANGLE
Mean solar position (deg) : 119.66 20.64
Mean aberration (arcsec) : 17.55 12.40
Mean sat X-axis (deg) : 12.066410 34.297214 92.01
Mean sat Y-axis (deg) : 127.107703 31.821974 13.01
Mean sat Z-axis (deg) : 247.864942 39.491952 102.85
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 247.509354 39.566566 47.127419 0.065001
Minimum 247.455673 39.560822 47.114494 0.000000
Maximum 247.581741 39.568268 47.291901 3.346763
Sigma (RMS) 0.000472 0.000073 0.002138 0.083505
Number of ASPECT records processed = 28750
Aspecting to RA/DEC : 247.50935364 39.56656647
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 175163030.64601 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 175174582.61063 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 175177401.10228 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 247.509 DEC: 39.567
START TIME: SC 175149761.1868 = UT 1998-07-21 04:42:41
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000137 2.387 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
115.999931 1.360 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
359.999084 0.575 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
2191.993408 0.079 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
6087.981445 0.096 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
7929.975586 0.035 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
11829.963867 0.055 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
17198.947266 0.016 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
17577.945312 0.014 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
19445.939453 0.041 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
23309.927734 0.029 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
26407.919922 0.028 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
29049.912109 0.031 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
30887.906250 0.046 88443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 1
34791.894531 0.036 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
36631.886719 0.072 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
40535.875000 0.040 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
42375.871094 0.041 88443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 1
46279.859375 0.023 D088C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 2
48103.851562 0.015 88443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 1
52023.839844 0.041 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
53847.835938 0.034 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
55067.832031 3.347 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 28750
Attitude Steps: 23
Maneuver ACM time: 17060.0 sec
Pointed ACM time: 38008.0 sec
-> Calculating aspect point99 99 count=2 sum1=495.623 sum2=101.026 sum3=273.87 100 99 count=9 sum1=2230.37 sum2=454.617 sum3=1232.35 100 100 count=1 sum1=247.814 sum2=50.514 sum3=136.929 101 99 count=12 sum1=2973.94 sum2=606.151 sum3=1643.05 102 99 count=19 sum1=4708.93 sum2=959.729 sum3=2601.36 103 99 count=47 sum1=11648.9 sum2=2374.06 sum3=6434.62 104 99 count=1621 sum1=401785 sum2=81873.8 sum3=221919 105 99 count=27038 sum1=6.70179e+06 sum2=1.36564e+06 sum3=3.70153e+06 112 99 count=1 sum1=247.938 sum2=50.507 sum3=137.065 0 out of 28750 points outside bin structure-> Euler angles: 247.865, 50.5082, 136.901
Interpolating 21 records in time interval 175204821.018 - 175204829.018
Dropping SF 75 with synch code word 0 = 254 not 250 605.998 second gap between superframes 76 and 77 Dropping SF 165 with synch code word 0 = 254 not 250 Dropping SF 213 with corrupted frame indicator Dropping SF 385 with synch code word 0 = 251 not 250 SIS0 coordinate error time=175152317.05394 x=2 y=0 pha[0]=0 chip=0 Dropping SF 556 with inconsistent datamode 0/31 Dropping SF 734 with corrupted frame indicator Dropping SF 812 with synch code word 0 = 254 not 250 Dropping SF 1552 with synch code word 0 = 254 not 250 Dropping SF 1584 with inconsistent CCD ID 2/3 Dropping SF 1701 with corrupted frame indicator 607.998 second gap between superframes 1900 and 1901 Dropping SF 1942 with corrupted frame indicator Dropping SF 2052 with synch code word 0 = 251 not 250 Dropping SF 3426 with corrupted frame indicator Dropping SF 3472 with corrupted frame indicator Dropping SF 3516 with synch code word 0 = 254 not 250 Dropping SF 3709 with synch code word 0 = 154 not 250 Dropping SF 3710 with synch code word 1 = 235 not 243 Dropping SF 3711 with synch code word 0 = 154 not 250 Dropping SF 3712 with synch code word 0 = 246 not 250 Dropping SF 3713 with synch code word 0 = 249 not 250 Dropping SF 3714 with synch code word 2 = 16 not 32 Dropping SF 3715 with synch code word 1 = 240 not 243 Dropping SF 3716 with synch code word 1 = 240 not 243 Dropping SF 3717 with inconsistent datamode 0/12 Dropping SF 3718 with synch code word 0 = 58 not 250 Dropping SF 3719 with synch code word 0 = 226 not 250 GIS2 coordinate error time=175166963.78732 x=128 y=0 pha=1 rise=0 SIS1 peak error time=175166953.009 x=368 y=213 ph0=216 ph3=2054 Dropping SF 3721 with synch code word 0 = 202 not 250 Dropping SF 3722 with synch code word 0 = 154 not 250 Dropping SF 3723 with synch code word 1 = 240 not 243 Dropping SF 3725 with synch code word 1 = 51 not 243 Dropping SF 3726 with synch code word 0 = 58 not 250 Dropping SF 3727 with synch code word 0 = 202 not 250 Dropping SF 3728 with synch code word 1 = 235 not 243 Dropping SF 3729 with synch code word 1 = 147 not 243 SIS0 coordinate error time=175166977.00893 x=0 y=0 pha[0]=768 chip=0 Dropping SF 3734 with synch code word 0 = 58 not 250 Dropping SF 3736 with synch code word 1 = 235 not 243 Dropping SF 3738 with synch code word 0 = 58 not 250 Dropping SF 3741 with synch code word 1 = 51 not 243 SIS1 coordinate error time=175166997.00887 x=0 y=0 pha[0]=1536 chip=0 Dropping SF 3744 with synch code word 0 = 226 not 250 Dropping SF 3745 with corrupted frame indicator SIS0 coordinate error time=175167009.00883 x=0 y=0 pha[0]=0 chip=3 Dropping SF 3748 with synch code word 0 = 246 not 250 Warning: GIS2 bit assignment changed between 175167019.13383 and 175167023.13382 SIS1 coordinate error time=175167013.00882 x=0 y=0 pha[0]=1536 chip=0 Warning: GIS2 bit assignment changed between 175167023.13382 and 175167025.13381 SIS0 coordinate error time=175167021.0088 x=0 y=12 pha[0]=0 chip=0 GIS2 coordinate error time=175167031.5918 x=192 y=0 pha=0 rise=0 GIS3 coordinate error time=175167031.99024 x=0 y=0 pha=512 rise=0 Dropping SF 3754 with synch code word 1 = 235 not 243 GIS2 coordinate error time=175167036.71288 x=0 y=0 pha=6 rise=0 Dropping SF 3756 with synch code word 0 = 251 not 250 Dropping SF 3757 with corrupted frame indicator Dropping SF 3758 with synch code word 1 = 242 not 243 Dropping SF 3759 with synch code word 0 = 154 not 250 Dropping SF 3760 with synch code word 1 = 235 not 243 Dropping SF 3761 with synch code word 0 = 246 not 250 GIS2 coordinate error time=175167050.47456 x=12 y=0 pha=0 rise=0 SIS0 coordinate error time=175167041.00874 x=256 y=0 pha[0]=0 chip=1 Dropping SF 3763 with synch code word 1 = 51 not 243 Dropping SF 3764 with synch code word 1 = 147 not 243 Dropping SF 3765 with synch code word 0 = 202 not 250 Dropping SF 3766 with corrupted frame indicator Dropping SF 3767 with synch code word 1 = 240 not 243 Dropping SF 3768 with synch code word 1 = 240 not 243 Dropping SF 3769 with synch code word 0 = 58 not 250 Dropping SF 3770 with synch code word 0 = 122 not 250 Dropping SF 3771 with corrupted frame indicator Dropping SF 3772 with synch code word 0 = 202 not 250 Dropping SF 3773 with corrupted frame indicator Dropping SF 3774 with synch code word 1 = 240 not 243 Dropping SF 3775 with synch code word 1 = 245 not 243 Dropping SF 3776 with corrupted frame indicator Dropping SF 3777 with synch code word 2 = 44 not 32 Dropping SF 3778 with synch code word 0 = 226 not 250 Dropping SF 3779 with corrupted frame indicator Dropping SF 3780 with synch code word 0 = 226 not 250 Dropping SF 3781 with synch code word 0 = 202 not 250 Dropping SF 3782 with synch code word 1 = 147 not 243 Dropping SF 3783 with synch code word 1 = 147 not 243 Dropping SF 3784 with synch code word 1 = 255 not 243 Dropping SF 3785 with corrupted frame indicator Dropping SF 3789 with synch code word 1 = 240 not 243 Dropping SF 3794 with synch code word 2 = 16 not 32 Dropping SF 3836 with synch code word 0 = 246 not 250 SIS0 coordinate error time=175167217.0082 x=0 y=0 pha[0]=192 chip=0 Dropping SF 3862 with corrupted frame indicator Dropping SF 3870 with corrupted frame indicator Dropping SF 3874 with inconsistent SIS mode 1/0 SIS0 peak error time=175167277.00802 x=168 y=248 ph0=203 ph4=223 ph5=221 ph6=219 ph7=229 Dropping SF 3881 with synch code word 0 = 251 not 250 GIS2 coordinate error time=175167305.43081 x=128 y=0 pha=1 rise=0 Dropping SF 3890 with corrupted frame indicator Dropping SF 3896 with synch code word 0 = 58 not 250 Dropping SF 3902 with synch code word 2 = 64 not 32 Dropping SF 3904 with synch code word 0 = 58 not 250 Dropping SF 3905 with corrupted frame indicator Dropping SF 3906 with synch code word 1 = 147 not 243 Dropping SF 3907 with corrupted frame indicator GIS2 coordinate error time=175167344.75491 x=12 y=0 pha=0 rise=0 GIS2 coordinate error time=175167346.07522 x=0 y=0 pha=768 rise=0 GIS2 coordinate error time=175167346.96584 x=0 y=0 pha=192 rise=0 Dropping SF 3910 with corrupted frame indicator Dropping SF 3912 with synch code word 0 = 249 not 250 Dropping SF 3913 with synch code word 1 = 147 not 243 Dropping SF 3914 with synch code word 1 = 235 not 243 Dropping SF 3915 with synch code word 0 = 58 not 250 Dropping SF 3916 with synch code word 0 = 246 not 250 Dropping SF 3919 with synch code word 0 = 58 not 250 Dropping SF 3920 with synch code word 2 = 16 not 32 GIS2 coordinate error time=175167369.81343 x=0 y=0 pha=24 rise=0 SIS0 coordinate error time=175167361.00776 x=1 y=256 pha[0]=0 chip=0 SIS0 coordinate error time=175167361.00776 x=6 y=0 pha[0]=0 chip=0 SIS0 coordinate error time=175167361.00776 x=0 y=1 pha[0]=2048 chip=0 SIS0 coordinate error time=175167361.00776 x=0 y=48 pha[0]=0 chip=0 Dropping SF 3922 with synch code word 1 = 51 not 243 Dropping SF 3923 with synch code word 1 = 51 not 243 Dropping SF 3924 with synch code word 0 = 122 not 250 Dropping SF 3925 with synch code word 0 = 202 not 250 Dropping SF 3926 with synch code word 0 = 226 not 250 Dropping SF 3927 with synch code word 0 = 252 not 250 Dropping SF 3928 with synch code word 2 = 44 not 32 Dropping SF 3929 with synch code word 0 = 202 not 250 Dropping SF 3930 with corrupted frame indicator Dropping SF 3931 with synch code word 1 = 240 not 243 Dropping SF 3932 with corrupted frame indicator Dropping SF 3933 with synch code word 0 = 226 not 250 Dropping SF 3934 with inconsistent datamode 0/31 Dropping SF 3935 with inconsistent datamode 0/31 Dropping SF 3936 with synch code word 1 = 195 not 243 Dropping SF 3937 with synch code word 1 = 195 not 243 Dropping SF 3938 with corrupted frame indicator Dropping SF 3939 with inconsistent datamode 0/31 Dropping SF 3940 with invalid bit rate 7 Dropping SF 3941 with invalid bit rate 7 Dropping SF 3942 with inconsistent datamode 0/31 Dropping SF 3943 with inconsistent datamode 0/31 Dropping SF 3944 with synch code word 1 = 195 not 243 Dropping SF 3945 with inconsistent datamode 0/31 Dropping SF 3946 with inconsistent datamode 0/16 Dropping SF 3947 with inconsistent datamode 0/31 Dropping SF 3948 with inconsistent datamode 0/31 Dropping SF 3949 with inconsistent datamode 0/31 Dropping SF 3950 with synch code word 0 = 246 not 250 Dropping SF 3951 with inconsistent datamode 0/31 Dropping SF 3952 with inconsistent datamode 0/31 Dropping SF 3953 with synch code word 1 = 147 not 243 Dropping SF 3954 with corrupted frame indicator Dropping SF 3955 with synch code word 1 = 255 not 243 Dropping SF 3956 with synch code word 0 = 226 not 250 Dropping SF 3957 with synch code word 0 = 202 not 250 Dropping SF 3958 with synch code word 1 = 147 not 243 Dropping SF 3959 with invalid bit rate 7 Dropping SF 3960 with synch code word 1 = 147 not 243 Dropping SF 3961 with corrupted frame indicator Dropping SF 3962 with synch code word 2 = 64 not 32 Dropping SF 3963 with inconsistent datamode 0/31 Dropping SF 3964 with corrupted frame indicator Dropping SF 3965 with corrupted frame indicator Dropping SF 3966 with corrupted frame indicator Dropping SF 3967 with synch code word 0 = 249 not 250 Dropping SF 3968 with inconsistent datamode 0/1 Dropping SF 3969 with synch code word 0 = 226 not 250 Dropping SF 3970 with corrupted frame indicator Dropping SF 3971 with inconsistent datamode 6/0 Dropping SF 3972 with inconsistent datamode 0/16 Dropping SF 3973 with synch code word 0 = 58 not 250 Dropping SF 3974 with corrupted frame indicator Dropping SF 3975 with synch code word 1 = 242 not 243 Dropping SF 3976 with synch code word 1 = 242 not 243 Dropping SF 3977 with corrupted frame indicator Dropping SF 3978 with synch code word 0 = 58 not 250 Dropping SF 3979 with inconsistent datamode 0/12 Dropping SF 3980 with invalid bit rate 7 Dropping SF 3981 with inconsistent datamode 0/31 Dropping SF 3982 with synch code word 1 = 240 not 243 Dropping SF 3983 with corrupted frame indicator Dropping SF 3984 with synch code word 0 = 202 not 250 Dropping SF 3985 with synch code word 1 = 195 not 243 Dropping SF 3986 with inconsistent datamode 0/31 Dropping SF 3987 with synch code word 0 = 246 not 250 Dropping SF 3988 with synch code word 0 = 202 not 250 Dropping SF 3989 with synch code word 0 = 58 not 250 Dropping SF 3990 with synch code word 0 = 255 not 250 Dropping SF 3991 with invalid bit rate 7 Dropping SF 3992 with corrupted frame indicator Dropping SF 3993 with inconsistent datamode 0/6 Dropping SF 3994 with inconsistent datamode 0/31 Dropping SF 3995 with synch code word 0 = 58 not 250 Dropping SF 3996 with corrupted frame indicator GIS2 coordinate error time=175167751.01539 x=0 y=0 pha=192 rise=0 SIS0 coordinate error time=175167741.00661 x=0 y=1 pha[0]=2048 chip=0 SIS0 coordinate error time=175167741.00661 x=0 y=24 pha[0]=0 chip=0 SIS0 coordinate error time=175167741.00661 x=0 y=48 pha[0]=0 chip=0 Dropping SF 3998 with synch code word 1 = 51 not 243 Dropping SF 3999 with synch code word 1 = 147 not 243 Dropping SF 4000 with corrupted frame indicator SIS0 coordinate error time=175167749.00658 x=0 y=0 pha[0]=48 chip=0 SIS0 coordinate error time=175167749.00658 x=0 y=0 pha[0]=192 chip=0 Dropping SF 4002 with synch code word 2 = 16 not 32 SIS1 coordinate error time=175167761.00654 x=0 y=192 pha[0]=0 chip=0 Dropping SF 4005 with synch code word 1 = 235 not 243 Dropping SF 4006 with corrupted frame indicator Dropping SF 4007 with corrupted frame indicator Dropping SF 4008 with corrupted frame indicator GIS2 coordinate error time=175167781.39811 x=0 y=0 pha=48 rise=0 GIS2 coordinate error time=175167781.7028 x=0 y=0 pha=768 rise=0 SIS0 coordinate error time=175167773.00651 x=0 y=0 pha[0]=0 chip=3 Dropping SF 4010 with synch code word 0 = 154 not 250 SIS0 coordinate error time=175167777.0065 x=0 y=0 pha[0]=1536 chip=0 Dropping SF 4013 with synch code word 1 = 235 not 243 SIS1 coordinate error time=175167781.00648 x=0 y=96 pha[0]=0 chip=0 SIS1 coordinate error time=175167781.00648 x=0 y=48 pha[0]=0 chip=0 SIS1 coordinate error time=175167781.00648 x=0 y=0 pha[0]=384 chip=0 Dropping SF 4015 with synch code word 0 = 226 not 250 Dropping SF 4016 with synch code word 0 = 249 not 250 Dropping SF 4021 with synch code word 0 = 154 not 250 Dropping SF 4022 with synch code word 1 = 147 not 243 Dropping SF 4028 with corrupted frame indicator Dropping SF 4029 with synch code word 1 = 51 not 243 Dropping SF 4033 with synch code word 0 = 154 not 250 Dropping SF 4036 with synch code word 0 = 154 not 250 SIS0 coordinate error time=175167841.0063 x=0 y=0 pha[0]=0 chip=3 Dropping SF 4047 with synch code word 1 = 240 not 243 Dropping SF 4054 with synch code word 1 = 147 not 243 Dropping SF 4091 with synch code word 0 = 226 not 250 Dropping SF 4098 with synch code word 0 = 154 not 250 Dropping SF 4105 with inconsistent datamode 0/1 Dropping SF 4108 with synch code word 1 = 51 not 243 Dropping SF 4111 with inconsistent CCD ID 3/0 Dropping SF 4112 with synch code word 1 = 240 not 243 SIS0 coordinate error time=175167993.00584 x=0 y=6 pha[0]=0 chip=0 SIS0 coordinate error time=175167993.00584 x=6 y=0 pha[0]=0 chip=0 Dropping SF 4119 with invalid bit rate 7 Dropping SF 4120 with corrupted frame indicator Dropping SF 4122 with synch code word 0 = 122 not 250 Dropping SF 4123 with corrupted frame indicator SIS0 coordinate error time=175168005.0058 x=192 y=0 pha[0]=0 chip=0 Dropping SF 4125 with synch code word 0 = 154 not 250 Dropping SF 4126 with synch code word 0 = 156 not 250 Dropping SF 4127 with inconsistent datamode 0/1 Dropping SF 4129 with corrupted frame indicator Dropping SF 4130 with synch code word 1 = 195 not 243 Dropping SF 4131 with synch code word 0 = 246 not 250 GIS2 coordinate error time=175168030.85829 x=128 y=0 pha=1 rise=0 GIS2 coordinate error time=175168031.10438 x=0 y=0 pha=6 rise=0 3.99998 second gap between superframes 4132 and 4133 Dropping SF 4134 with synch code word 0 = 58 not 250 Dropping SF 4135 with synch code word 1 = 245 not 243 GIS2 coordinate error time=175168041.33091 x=0 y=0 pha=24 rise=0 SIS0 coordinate error time=175168033.00572 x=0 y=0 pha[0]=3072 chip=0 Dropping SF 4137 with inconsistent SIS ID Dropping SF 4138 with synch code word 0 = 202 not 250 Dropping SF 4139 with synch code word 0 = 202 not 250 Dropping SF 4140 with synch code word 2 = 16 not 32 Dropping SF 4141 with invalid bit rate 7 SIS0 coordinate error time=175168049.00817 x=0 y=0 pha[0]=1 chip=0 SIS0 peak error time=175168049.00817 x=0 y=0 ph0=1 ph1=1984 Dropping SF 4143 with synch code word 2 = 16 not 32 Dropping SF 4144 with synch code word 0 = 202 not 250 Dropping SF 4145 with synch code word 2 = 56 not 32 Dropping SF 4146 with synch code word 0 = 58 not 250 Dropping SF 4147 with invalid bit rate 7 Dropping SF 4148 with synch code word 1 = 147 not 243 Dropping SF 4149 with corrupted frame indicator Dropping SF 4150 with synch code word 2 = 16 not 32 Dropping SF 4151 with synch code word 2 = 16 not 32 Dropping SF 4152 with inconsistent datamode 0/31 Dropping SF 4153 with inconsistent datamode 0/31 Dropping SF 4154 with synch code word 0 = 202 not 250 Dropping SF 4155 with synch code word 1 = 240 not 243 Dropping SF 4156 with synch code word 0 = 252 not 250 Dropping SF 4157 with inconsistent datamode 0/31 Dropping SF 4158 with inconsistent datamode 0/3 Dropping SF 4159 with synch code word 0 = 246 not 250 Dropping SF 4160 with corrupted frame indicator Dropping SF 4161 with synch code word 1 = 240 not 243 Dropping SF 4162 with synch code word 0 = 251 not 250 Dropping SF 4163 with synch code word 0 = 252 not 250 GIS2 coordinate error time=175168151.49464 x=0 y=0 pha=12 rise=0 SIS1 coordinate error time=175168141.00538 x=0 y=0 pha[0]=0 chip=3 SIS1 coordinate error time=175168141.00538 x=0 y=0 pha[0]=3072 chip=0 SIS1 coordinate error time=175168141.00538 x=0 y=0 pha[0]=192 chip=0 SIS1 coordinate error time=175168141.00538 x=3 y=0 pha[0]=0 chip=0 GIS2 coordinate error time=175168153.34229 x=0 y=0 pha=768 rise=0 SIS0 coordinate error time=175168145.00537 x=0 y=3 pha[0]=0 chip=0 Dropping SF 4168 with synch code word 1 = 240 not 243 Dropping SF 4169 with synch code word 1 = 51 not 243 Dropping SF 4170 with synch code word 1 = 240 not 243 Dropping SF 4171 with synch code word 0 = 246 not 250 Dropping SF 4176 with synch code word 1 = 51 not 243 Dropping SF 4177 with synch code word 1 = 51 not 243 Dropping SF 4178 with synch code word 1 = 147 not 243 Dropping SF 4179 with corrupted frame indicator Dropping SF 4185 with synch code word 0 = 154 not 250 Dropping SF 4186 with synch code word 1 = 242 not 243 Dropping SF 4191 with corrupted frame indicator Dropping SF 4192 with synch code word 0 = 122 not 250 Dropping SF 4193 with synch code word 0 = 226 not 250 Dropping SF 4200 with synch code word 1 = 235 not 243 Dropping SF 4201 with synch code word 1 = 195 not 243 Dropping SF 4206 with synch code word 0 = 154 not 250 Dropping SF 4207 with synch code word 0 = 154 not 250 Dropping SF 4208 with synch code word 0 = 58 not 250 Dropping SF 4214 with synch code word 1 = 147 not 243 Dropping SF 4215 with synch code word 0 = 249 not 250 GIS2 coordinate error time=175168266.28726 x=96 y=0 pha=0 rise=0 Dropping SF 4222 with synch code word 1 = 195 not 243 SIS1 coordinate error time=175168269.00499 x=0 y=0 pha[0]=1 chip=0 SIS1 peak error time=175168269.00499 x=0 y=0 ph0=1 ph1=1984 Dropping SF 4229 with synch code word 2 = 44 not 32 Warning: GIS2 bit assignment changed between 175168279.12999 and 175168283.12998 Warning: GIS2 bit assignment changed between 175168283.12998 and 175168285.12997 GIS2 coordinate error time=175168294.63092 x=0 y=0 pha=3 rise=0 Dropping SF 4236 with synch code word 1 = 240 not 243 Dropping SF 4237 with synch code word 1 = 51 not 243 SIS1 coordinate error time=175168297.0049 x=0 y=0 pha[0]=0 chip=2 Dropping SF 4243 with inconsistent continuation flag Dropping SF 4244 with synch code word 0 = 246 not 250 Dropping SF 4250 with synch code word 2 = 16 not 32 Dropping SF 4251 with synch code word 0 = 58 not 250 GIS2 coordinate error time=175168327.32222 x=0 y=0 pha=12 rise=0 Dropping SF 4254 with synch code word 0 = 154 not 250 Dropping SF 4258 with synch code word 0 = 202 not 250 Dropping SF 4259 with synch code word 0 = 58 not 250 Dropping SF 4260 with corrupted frame indicator GIS2 coordinate error time=175168347.30654 x=192 y=0 pha=0 rise=0 GIS2 coordinate error time=175168348.24013 x=96 y=0 pha=0 rise=0 GIS2 coordinate error time=175168348.26748 x=128 y=0 pha=1 rise=0 Dropping SF 4264 with corrupted frame indicator Dropping SF 4265 with synch code word 1 = 242 not 243 Dropping SF 4266 with synch code word 1 = 240 not 243 Dropping SF 4269 with synch code word 1 = 235 not 243 Dropping SF 4270 with synch code word 1 = 195 not 243 Dropping SF 4271 with synch code word 1 = 147 not 243 Dropping SF 4272 with inconsistent datamode 0/1 Dropping SF 4273 with synch code word 1 = 195 not 243 Dropping SF 4274 with corrupted frame indicator GIS2 coordinate error time=175168375.3338 x=0 y=0 pha=24 rise=0 GIS2 coordinate error time=175168376.44317 x=0 y=0 pha=12 rise=0 SIS1 coordinate error time=175168365.00469 x=0 y=0 pha[0]=0 chip=2 Dropping SF 4277 with synch code word 2 = 64 not 32 Dropping SF 4278 with synch code word 0 = 202 not 250 GIS2 coordinate error time=175168382.59159 x=0 y=0 pha=384 rise=0 GIS2 coordinate error time=175168382.98612 x=0 y=0 pha=3 rise=0 GIS2 coordinate error time=175168383.06034 x=192 y=0 pha=0 rise=0 SIS0 coordinate error time=175168373.00468 x=0 y=1 pha[0]=2048 chip=0 SIS0 coordinate error time=175168373.00468 x=0 y=192 pha[0]=0 chip=0 Dropping SF 4280 with synch code word 0 = 58 not 250 Dropping SF 4281 with synch code word 0 = 58 not 250 Dropping SF 4283 with synch code word 0 = 246 not 250 Dropping SF 4284 with synch code word 1 = 51 not 243 Dropping SF 4287 with invalid bit rate 5 GIS2 coordinate error time=175168404.55246 x=12 y=0 pha=0 rise=0 GIS2 coordinate error time=175168404.5759 x=0 y=0 pha=192 rise=0 GIS2 coordinate error time=175168404.72434 x=128 y=0 pha=1 rise=0 GIS2 coordinate error time=175168404.93918 x=0 y=0 pha=192 rise=0 GIS2 coordinate error time=175168405.07199 x=128 y=0 pha=1 rise=0 SIS1 coordinate error time=175168393.00461 x=0 y=0 pha[0]=1 chip=0 SIS1 peak error time=175168393.00461 x=0 y=0 ph0=1 ph1=1984 SIS1 coordinate error time=175168393.00461 x=0 y=0 pha[0]=1536 chip=0 Dropping SF 4290 with synch code word 0 = 202 not 250 Dropping SF 4291 with synch code word 1 = 195 not 243 Dropping SF 4292 with synch code word 0 = 154 not 250 Dropping SF 4293 with synch code word 0 = 202 not 250 Dropping SF 4294 with synch code word 0 = 246 not 250 Dropping SF 4295 with synch code word 0 = 202 not 250 GIS2 coordinate error time=175168418.80242 x=0 y=0 pha=48 rise=0 GIS2 coordinate error time=175168418.98601 x=96 y=0 pha=0 rise=0 GIS2 coordinate error time=175168419.00554 x=24 y=0 pha=0 rise=0 SIS0 coordinate error time=175168409.00457 x=0 y=0 pha[0]=3 chip=0 Dropping SF 4297 with inconsistent datamode 0/16 Dropping SF 4298 with synch code word 0 = 226 not 250 Dropping SF 4299 with synch code word 0 = 226 not 250 Dropping SF 4300 with synch code word 1 = 235 not 243 Dropping SF 4301 with synch code word 1 = 240 not 243 Dropping SF 4302 with synch code word 0 = 58 not 250 Dropping SF 4303 with corrupted frame indicator Dropping SF 4304 with synch code word 0 = 226 not 250 Dropping SF 4305 with corrupted frame indicator Dropping SF 4306 with inconsistent datamode 0/31 Dropping SF 4348 with synch code word 2 = 156 not 32 607.998 second gap between superframes 4385 and 4386 Dropping SF 6192 with synch code word 0 = 154 not 250 GIS2 coordinate error time=175176159.88723 x=96 y=0 pha=0 rise=0 GIS2 coordinate error time=175176163.01223 x=48 y=0 pha=0 rise=0 GIS2 coordinate error time=175176168.88723 x=12 y=0 pha=0 rise=0 SIS1 coordinate error time=175176152.98098 x=1 y=256 pha[0]=0 chip=0 GIS2 coordinate error time=175176205.63704 x=0 y=0 pha=6 rise=0 GIS2 coordinate error time=175177412.63353 x=0 y=0 pha=384 rise=0 GIS2 coordinate error time=175177417.38353 x=0 y=0 pha=192 rise=0 Dropping SF 6213 with synch code word 0 = 249 not 250 Dropping SF 6214 with corrupted frame indicator Dropping SF 6215 with synch code word 1 = 242 not 243 Dropping SF 6216 with inconsistent datamode 0/12 Dropping SF 6217 with invalid bit rate 7 Dropping SF 6218 with invalid bit rate 7 Dropping SF 6219 with invalid bit rate 7 Dropping SF 6220 with inconsistent datamode 0/1 Dropping SF 6221 with inconsistent datamode 0/3 Dropping SF 6222 with corrupted frame indicator Dropping SF 6223 with inconsistent datamode 0/24 Dropping SF 6224 with synch code word 1 = 245 not 243 Dropping SF 6225 with invalid bit rate 7 Dropping SF 6226 with invalid bit rate 7 Dropping SF 6227 with invalid bit rate 7 Dropping SF 6228 with invalid bit rate 7 Dropping SF 6229 with inconsistent datamode 0/31 Dropping SF 6230 with invalid bit rate 7 Dropping SF 6231 with inconsistent datamode 12/0 Dropping SF 6232 with inconsistent datamode 0/31 Dropping SF 6233 with corrupted frame indicator Dropping SF 6234 with inconsistent datamode 0/31 7198 of 7518 super frames processed-> Removing the following files with NEVENTS=0
ft980721_0442_2000G201570M.fits[0] ft980721_0442_2000G204070H.fits[0] ft980721_0442_2000G204170H.fits[0] ft980721_0442_2000G204270M.fits[0] ft980721_0442_2000G204370M.fits[0] ft980721_0442_2000G205070L.fits[0] ft980721_0442_2000G205170L.fits[0] ft980721_0442_2000G205270L.fits[0] ft980721_0442_2000G205970L.fits[0] ft980721_0442_2000G206070M.fits[0] ft980721_0442_2000G206570L.fits[0] ft980721_0442_2000G206670M.fits[0] ft980721_0442_2000G207170L.fits[0] ft980721_0442_2000G207270M.fits[0] ft980721_0442_2000G207770L.fits[0] ft980721_0442_2000G207870M.fits[0] ft980721_0442_2000G207970M.fits[0] ft980721_0442_2000G208070M.fits[0] ft980721_0442_2000G208170M.fits[0] ft980721_0442_2000G301370M.fits[0] ft980721_0442_2000G304370H.fits[0] ft980721_0442_2000G304470H.fits[0] ft980721_0442_2000G304570M.fits[0] ft980721_0442_2000G304670M.fits[0] ft980721_0442_2000G305370L.fits[0] ft980721_0442_2000G305470L.fits[0] ft980721_0442_2000G306170L.fits[0] ft980721_0442_2000G306270M.fits[0] ft980721_0442_2000G306770L.fits[0] ft980721_0442_2000G306870M.fits[0] ft980721_0442_2000G307370L.fits[0] ft980721_0442_2000G307470M.fits[0] ft980721_0442_2000G307970L.fits[0] ft980721_0442_2000G308070M.fits[0] ft980721_0442_2000G308170M.fits[0] ft980721_0442_2000G308270M.fits[0] ft980721_0442_2000G308370M.fits[0] ft980721_0442_2000S002901L.fits[0] ft980721_0442_2000S003901L.fits[0] ft980721_0442_2000S004501L.fits[0] ft980721_0442_2000S005101L.fits[0] ft980721_0442_2000S005201L.fits[0] ft980721_0442_2000S101601L.fits[0] ft980721_0442_2000S103201L.fits[0]-> Checking for empty GTI extensions
ft980721_0442_2000S000101M.fits[2] ft980721_0442_2000S000201H.fits[2] ft980721_0442_2000S000301H.fits[2] ft980721_0442_2000S000401H.fits[2] ft980721_0442_2000S000501H.fits[2] ft980721_0442_2000S000601M.fits[2] ft980721_0442_2000S000701H.fits[2] ft980721_0442_2000S000801H.fits[2] ft980721_0442_2000S000901H.fits[2] ft980721_0442_2000S001001M.fits[2] ft980721_0442_2000S001101H.fits[2] ft980721_0442_2000S001201H.fits[2] ft980721_0442_2000S001301H.fits[2] ft980721_0442_2000S001401H.fits[2] ft980721_0442_2000S001501H.fits[2] ft980721_0442_2000S001601H.fits[2] ft980721_0442_2000S001701H.fits[2] ft980721_0442_2000S001801H.fits[2] ft980721_0442_2000S001901H.fits[2] ft980721_0442_2000S002001H.fits[2] ft980721_0442_2000S002101H.fits[2] ft980721_0442_2000S002201H.fits[2] ft980721_0442_2000S002301H.fits[2] ft980721_0442_2000S002401M.fits[2] ft980721_0442_2000S002501M.fits[2] ft980721_0442_2000S002601M.fits[2] ft980721_0442_2000S002701H.fits[2] ft980721_0442_2000S002801H.fits[2] ft980721_0442_2000S003001H.fits[2] ft980721_0442_2000S003101M.fits[2] ft980721_0442_2000S003201M.fits[2] ft980721_0442_2000S003301L.fits[2] ft980721_0442_2000S003401L.fits[2] ft980721_0442_2000S003501L.fits[2] ft980721_0442_2000S003601M.fits[2] ft980721_0442_2000S003701L.fits[2] ft980721_0442_2000S003801L.fits[2] ft980721_0442_2000S004001L.fits[2] ft980721_0442_2000S004101L.fits[2] ft980721_0442_2000S004201M.fits[2] ft980721_0442_2000S004301L.fits[2] ft980721_0442_2000S004401L.fits[2] ft980721_0442_2000S004601L.fits[2] ft980721_0442_2000S004701L.fits[2] ft980721_0442_2000S004801M.fits[2] ft980721_0442_2000S004901L.fits[2] ft980721_0442_2000S005001L.fits[2] ft980721_0442_2000S005301L.fits[2] ft980721_0442_2000S005401M.fits[2] ft980721_0442_2000S005501M.fits[2]-> Merging GTIs from the following files:
ft980721_0442_2000S100101M.fits[2] ft980721_0442_2000S100201H.fits[2] ft980721_0442_2000S100301M.fits[2] ft980721_0442_2000S100401H.fits[2] ft980721_0442_2000S100501M.fits[2] ft980721_0442_2000S100601H.fits[2] ft980721_0442_2000S100701H.fits[2] ft980721_0442_2000S100801H.fits[2] ft980721_0442_2000S100901H.fits[2] ft980721_0442_2000S101001H.fits[2] ft980721_0442_2000S101101H.fits[2] ft980721_0442_2000S101201M.fits[2] ft980721_0442_2000S101301M.fits[2] ft980721_0442_2000S101401M.fits[2] ft980721_0442_2000S101501H.fits[2] ft980721_0442_2000S101701H.fits[2] ft980721_0442_2000S101801M.fits[2] ft980721_0442_2000S101901L.fits[2] ft980721_0442_2000S102001L.fits[2] ft980721_0442_2000S102101L.fits[2] ft980721_0442_2000S102201M.fits[2] ft980721_0442_2000S102301L.fits[2] ft980721_0442_2000S102401L.fits[2] ft980721_0442_2000S102501L.fits[2] ft980721_0442_2000S102601M.fits[2] ft980721_0442_2000S102701L.fits[2] ft980721_0442_2000S102801L.fits[2] ft980721_0442_2000S102901L.fits[2] ft980721_0442_2000S103001M.fits[2] ft980721_0442_2000S103101L.fits[2] ft980721_0442_2000S103301L.fits[2] ft980721_0442_2000S103401M.fits[2]-> Merging GTIs from the following files:
ft980721_0442_2000G200170M.fits[2] ft980721_0442_2000G200270H.fits[2] ft980721_0442_2000G200370H.fits[2] ft980721_0442_2000G200470H.fits[2] ft980721_0442_2000G200570M.fits[2] ft980721_0442_2000G200670M.fits[2] ft980721_0442_2000G200770H.fits[2] ft980721_0442_2000G200870H.fits[2] ft980721_0442_2000G200970H.fits[2] ft980721_0442_2000G201070H.fits[2] ft980721_0442_2000G201170H.fits[2] ft980721_0442_2000G201270H.fits[2] ft980721_0442_2000G201370M.fits[2] ft980721_0442_2000G201470M.fits[2] ft980721_0442_2000G201670M.fits[2] ft980721_0442_2000G201770M.fits[2] ft980721_0442_2000G201870H.fits[2] ft980721_0442_2000G201970H.fits[2] ft980721_0442_2000G202070H.fits[2] ft980721_0442_2000G202170H.fits[2] ft980721_0442_2000G202270H.fits[2] ft980721_0442_2000G202370H.fits[2] ft980721_0442_2000G202470H.fits[2] ft980721_0442_2000G202570H.fits[2] ft980721_0442_2000G202670H.fits[2] ft980721_0442_2000G202770H.fits[2] ft980721_0442_2000G202870H.fits[2] ft980721_0442_2000G202970H.fits[2] ft980721_0442_2000G203070H.fits[2] ft980721_0442_2000G203170H.fits[2] ft980721_0442_2000G203270H.fits[2] ft980721_0442_2000G203370H.fits[2] ft980721_0442_2000G203470H.fits[2] ft980721_0442_2000G203570H.fits[2] ft980721_0442_2000G203670H.fits[2] ft980721_0442_2000G203770H.fits[2] ft980721_0442_2000G203870H.fits[2] ft980721_0442_2000G203970H.fits[2] ft980721_0442_2000G204470M.fits[2] ft980721_0442_2000G204570M.fits[2] ft980721_0442_2000G204670H.fits[2] ft980721_0442_2000G204770H.fits[2] ft980721_0442_2000G204870H.fits[2] ft980721_0442_2000G204970H.fits[2] ft980721_0442_2000G205370H.fits[2] ft980721_0442_2000G205470M.fits[2] ft980721_0442_2000G205570M.fits[2] ft980721_0442_2000G205670L.fits[2] ft980721_0442_2000G205770L.fits[2] ft980721_0442_2000G205870L.fits[2] ft980721_0442_2000G206170M.fits[2] ft980721_0442_2000G206270M.fits[2] ft980721_0442_2000G206370L.fits[2] ft980721_0442_2000G206470L.fits[2] ft980721_0442_2000G206770M.fits[2] ft980721_0442_2000G206870M.fits[2] ft980721_0442_2000G206970L.fits[2] ft980721_0442_2000G207070L.fits[2] ft980721_0442_2000G207370M.fits[2] ft980721_0442_2000G207470M.fits[2] ft980721_0442_2000G207570L.fits[2] ft980721_0442_2000G207670L.fits[2] ft980721_0442_2000G208270M.fits[2] ft980721_0442_2000G208370M.fits[2]-> Merging GTIs from the following files:
ft980721_0442_2000G300170M.fits[2] ft980721_0442_2000G300270H.fits[2] ft980721_0442_2000G300370M.fits[2] ft980721_0442_2000G300470M.fits[2] ft980721_0442_2000G300570H.fits[2] ft980721_0442_2000G300670H.fits[2] ft980721_0442_2000G300770H.fits[2] ft980721_0442_2000G300870H.fits[2] ft980721_0442_2000G300970H.fits[2] ft980721_0442_2000G301070H.fits[2] ft980721_0442_2000G301170M.fits[2] ft980721_0442_2000G301270M.fits[2] ft980721_0442_2000G301470M.fits[2] ft980721_0442_2000G301570M.fits[2] ft980721_0442_2000G301670H.fits[2] ft980721_0442_2000G301770H.fits[2] ft980721_0442_2000G301870H.fits[2] ft980721_0442_2000G301970H.fits[2] ft980721_0442_2000G302070H.fits[2] ft980721_0442_2000G302170H.fits[2] ft980721_0442_2000G302270H.fits[2] ft980721_0442_2000G302370H.fits[2] ft980721_0442_2000G302470H.fits[2] ft980721_0442_2000G302570H.fits[2] ft980721_0442_2000G302670H.fits[2] ft980721_0442_2000G302770H.fits[2] ft980721_0442_2000G302870H.fits[2] ft980721_0442_2000G302970H.fits[2] ft980721_0442_2000G303070H.fits[2] ft980721_0442_2000G303170H.fits[2] ft980721_0442_2000G303270H.fits[2] ft980721_0442_2000G303370H.fits[2] ft980721_0442_2000G303470H.fits[2] ft980721_0442_2000G303570H.fits[2] ft980721_0442_2000G303670H.fits[2] ft980721_0442_2000G303770H.fits[2] ft980721_0442_2000G303870H.fits[2] ft980721_0442_2000G303970H.fits[2] ft980721_0442_2000G304070H.fits[2] ft980721_0442_2000G304170H.fits[2] ft980721_0442_2000G304270H.fits[2] ft980721_0442_2000G304770M.fits[2] ft980721_0442_2000G304870M.fits[2] ft980721_0442_2000G304970H.fits[2] ft980721_0442_2000G305070H.fits[2] ft980721_0442_2000G305170H.fits[2] ft980721_0442_2000G305270H.fits[2] ft980721_0442_2000G305570H.fits[2] ft980721_0442_2000G305670M.fits[2] ft980721_0442_2000G305770M.fits[2] ft980721_0442_2000G305870L.fits[2] ft980721_0442_2000G305970L.fits[2] ft980721_0442_2000G306070L.fits[2] ft980721_0442_2000G306370M.fits[2] ft980721_0442_2000G306470M.fits[2] ft980721_0442_2000G306570L.fits[2] ft980721_0442_2000G306670L.fits[2] ft980721_0442_2000G306970M.fits[2] ft980721_0442_2000G307070M.fits[2] ft980721_0442_2000G307170L.fits[2] ft980721_0442_2000G307270L.fits[2] ft980721_0442_2000G307570M.fits[2] ft980721_0442_2000G307670M.fits[2] ft980721_0442_2000G307770L.fits[2] ft980721_0442_2000G307870L.fits[2] ft980721_0442_2000G308470M.fits[2] ft980721_0442_2000G308570M.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200870h.prelist merge count = 15 photon cnt = 23904 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g201070h.prelist merge count = 3 photon cnt = 22 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g201870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201970h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g202070h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 53 GISSORTSPLIT:LO:g200270l.prelist merge count = 4 photon cnt = 5763 GISSORTSPLIT:LO:g200370l.prelist merge count = 3 photon cnt = 263 GISSORTSPLIT:LO:g200170m.prelist merge count = 6 photon cnt = 190 GISSORTSPLIT:LO:g200270m.prelist merge count = 10 photon cnt = 38447 GISSORTSPLIT:LO:g200370m.prelist merge count = 3 photon cnt = 138 GISSORTSPLIT:LO:Total filenames split = 64 GISSORTSPLIT:LO:Total split file cnt = 26 GISSORTSPLIT:LO:End program-> Creating ad86068000g200170m.unf
---- cmerge: version 1.6 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G200170M.fits 2 -- ft980721_0442_2000G200670M.fits 3 -- ft980721_0442_2000G201470M.fits 4 -- ft980721_0442_2000G201770M.fits 5 -- ft980721_0442_2000G204570M.fits 6 -- ft980721_0442_2000G205570M.fits 7 -- ft980721_0442_2000G206270M.fits 8 -- ft980721_0442_2000G206870M.fits 9 -- ft980721_0442_2000G207470M.fits 10 -- ft980721_0442_2000G208370M.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G200170M.fits 2 -- ft980721_0442_2000G200670M.fits 3 -- ft980721_0442_2000G201470M.fits 4 -- ft980721_0442_2000G201770M.fits 5 -- ft980721_0442_2000G204570M.fits 6 -- ft980721_0442_2000G205570M.fits 7 -- ft980721_0442_2000G206270M.fits 8 -- ft980721_0442_2000G206870M.fits 9 -- ft980721_0442_2000G207470M.fits 10 -- ft980721_0442_2000G208370M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000g200270h.unf
---- cmerge: version 1.6 ---- A total of 15 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G200270H.fits 2 -- ft980721_0442_2000G200470H.fits 3 -- ft980721_0442_2000G201070H.fits 4 -- ft980721_0442_2000G201270H.fits 5 -- ft980721_0442_2000G202170H.fits 6 -- ft980721_0442_2000G202370H.fits 7 -- ft980721_0442_2000G202570H.fits 8 -- ft980721_0442_2000G202770H.fits 9 -- ft980721_0442_2000G202970H.fits 10 -- ft980721_0442_2000G203270H.fits 11 -- ft980721_0442_2000G203470H.fits 12 -- ft980721_0442_2000G203670H.fits 13 -- ft980721_0442_2000G203970H.fits 14 -- ft980721_0442_2000G204970H.fits 15 -- ft980721_0442_2000G205370H.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G200270H.fits 2 -- ft980721_0442_2000G200470H.fits 3 -- ft980721_0442_2000G201070H.fits 4 -- ft980721_0442_2000G201270H.fits 5 -- ft980721_0442_2000G202170H.fits 6 -- ft980721_0442_2000G202370H.fits 7 -- ft980721_0442_2000G202570H.fits 8 -- ft980721_0442_2000G202770H.fits 9 -- ft980721_0442_2000G202970H.fits 10 -- ft980721_0442_2000G203270H.fits 11 -- ft980721_0442_2000G203470H.fits 12 -- ft980721_0442_2000G203670H.fits 13 -- ft980721_0442_2000G203970H.fits 14 -- ft980721_0442_2000G204970H.fits 15 -- ft980721_0442_2000G205370H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000g200370l.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G205770L.fits 2 -- ft980721_0442_2000G206370L.fits 3 -- ft980721_0442_2000G207070L.fits 4 -- ft980721_0442_2000G207670L.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G205770L.fits 2 -- ft980721_0442_2000G206370L.fits 3 -- ft980721_0442_2000G207070L.fits 4 -- ft980721_0442_2000G207670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000263 events
ft980721_0442_2000G205670L.fits ft980721_0442_2000G206970L.fits ft980721_0442_2000G207570L.fits-> Ignoring the following files containing 000000190 events
ft980721_0442_2000G201670M.fits ft980721_0442_2000G204470M.fits ft980721_0442_2000G206170M.fits ft980721_0442_2000G206770M.fits ft980721_0442_2000G207370M.fits ft980721_0442_2000G208270M.fits-> Ignoring the following files containing 000000138 events
ft980721_0442_2000G200570M.fits ft980721_0442_2000G201370M.fits ft980721_0442_2000G205470M.fits-> Ignoring the following files containing 000000053 events
ft980721_0442_2000G205870L.fits ft980721_0442_2000G206470L.fits-> Ignoring the following files containing 000000022 events
ft980721_0442_2000G200970H.fits ft980721_0442_2000G202070H.fits ft980721_0442_2000G204870H.fits-> Ignoring the following files containing 000000013 events
ft980721_0442_2000G203770H.fits-> Ignoring the following files containing 000000012 events
ft980721_0442_2000G203370H.fits-> Ignoring the following files containing 000000009 events
ft980721_0442_2000G200770H.fits-> Ignoring the following files containing 000000009 events
ft980721_0442_2000G200370H.fits-> Ignoring the following files containing 000000009 events
ft980721_0442_2000G202670H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G204770H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G203070H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G203170H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G201970H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G201870H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G200870H.fits-> Ignoring the following files containing 000000005 events
ft980721_0442_2000G204670H.fits-> Ignoring the following files containing 000000005 events
ft980721_0442_2000G202870H.fits-> Ignoring the following files containing 000000005 events
ft980721_0442_2000G203570H.fits-> Ignoring the following files containing 000000004 events
ft980721_0442_2000G203870H.fits-> Ignoring the following files containing 000000003 events
ft980721_0442_2000G202470H.fits-> Ignoring the following files containing 000000003 events
ft980721_0442_2000G201170H.fits-> Ignoring the following files containing 000000002 events
ft980721_0442_2000G202270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300570h.prelist merge count = 2 photon cnt = 9 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301170h.prelist merge count = 16 photon cnt = 20715 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301470h.prelist merge count = 3 photon cnt = 14 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301870h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g302070h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g302170h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300170l.prelist merge count = 2 photon cnt = 54 GISSORTSPLIT:LO:g300270l.prelist merge count = 4 photon cnt = 5699 GISSORTSPLIT:LO:g300370l.prelist merge count = 3 photon cnt = 247 GISSORTSPLIT:LO:g300170m.prelist merge count = 6 photon cnt = 185 GISSORTSPLIT:LO:g300270m.prelist merge count = 10 photon cnt = 34731 GISSORTSPLIT:LO:g300370m.prelist merge count = 3 photon cnt = 81 GISSORTSPLIT:LO:Total filenames split = 67 GISSORTSPLIT:LO:Total split file cnt = 27 GISSORTSPLIT:LO:End program-> Creating ad86068000g300170m.unf
---- cmerge: version 1.6 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G300170M.fits 2 -- ft980721_0442_2000G300470M.fits 3 -- ft980721_0442_2000G301270M.fits 4 -- ft980721_0442_2000G301570M.fits 5 -- ft980721_0442_2000G304870M.fits 6 -- ft980721_0442_2000G305770M.fits 7 -- ft980721_0442_2000G306470M.fits 8 -- ft980721_0442_2000G307070M.fits 9 -- ft980721_0442_2000G307670M.fits 10 -- ft980721_0442_2000G308570M.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G300170M.fits 2 -- ft980721_0442_2000G300470M.fits 3 -- ft980721_0442_2000G301270M.fits 4 -- ft980721_0442_2000G301570M.fits 5 -- ft980721_0442_2000G304870M.fits 6 -- ft980721_0442_2000G305770M.fits 7 -- ft980721_0442_2000G306470M.fits 8 -- ft980721_0442_2000G307070M.fits 9 -- ft980721_0442_2000G307670M.fits 10 -- ft980721_0442_2000G308570M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000g300270h.unf
---- cmerge: version 1.6 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G300270H.fits 2 -- ft980721_0442_2000G300870H.fits 3 -- ft980721_0442_2000G301070H.fits 4 -- ft980721_0442_2000G301970H.fits 5 -- ft980721_0442_2000G302170H.fits 6 -- ft980721_0442_2000G302370H.fits 7 -- ft980721_0442_2000G302570H.fits 8 -- ft980721_0442_2000G302970H.fits 9 -- ft980721_0442_2000G303170H.fits 10 -- ft980721_0442_2000G303370H.fits 11 -- ft980721_0442_2000G303570H.fits 12 -- ft980721_0442_2000G303770H.fits 13 -- ft980721_0442_2000G304070H.fits 14 -- ft980721_0442_2000G304270H.fits 15 -- ft980721_0442_2000G305270H.fits 16 -- ft980721_0442_2000G305570H.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G300270H.fits 2 -- ft980721_0442_2000G300870H.fits 3 -- ft980721_0442_2000G301070H.fits 4 -- ft980721_0442_2000G301970H.fits 5 -- ft980721_0442_2000G302170H.fits 6 -- ft980721_0442_2000G302370H.fits 7 -- ft980721_0442_2000G302570H.fits 8 -- ft980721_0442_2000G302970H.fits 9 -- ft980721_0442_2000G303170H.fits 10 -- ft980721_0442_2000G303370H.fits 11 -- ft980721_0442_2000G303570H.fits 12 -- ft980721_0442_2000G303770H.fits 13 -- ft980721_0442_2000G304070H.fits 14 -- ft980721_0442_2000G304270H.fits 15 -- ft980721_0442_2000G305270H.fits 16 -- ft980721_0442_2000G305570H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000g300370l.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000G305970L.fits 2 -- ft980721_0442_2000G306570L.fits 3 -- ft980721_0442_2000G307270L.fits 4 -- ft980721_0442_2000G307870L.fits Merging binary extension #: 2 1 -- ft980721_0442_2000G305970L.fits 2 -- ft980721_0442_2000G306570L.fits 3 -- ft980721_0442_2000G307270L.fits 4 -- ft980721_0442_2000G307870L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000247 events
ft980721_0442_2000G305870L.fits ft980721_0442_2000G307170L.fits ft980721_0442_2000G307770L.fits-> Ignoring the following files containing 000000185 events
ft980721_0442_2000G301470M.fits ft980721_0442_2000G304770M.fits ft980721_0442_2000G306370M.fits ft980721_0442_2000G306970M.fits ft980721_0442_2000G307570M.fits ft980721_0442_2000G308470M.fits-> Ignoring the following files containing 000000081 events
ft980721_0442_2000G300370M.fits ft980721_0442_2000G301170M.fits ft980721_0442_2000G305670M.fits-> Ignoring the following files containing 000000054 events
ft980721_0442_2000G306070L.fits ft980721_0442_2000G306670L.fits-> Ignoring the following files containing 000000014 events
ft980721_0442_2000G300770H.fits ft980721_0442_2000G301870H.fits ft980721_0442_2000G305170H.fits-> Ignoring the following files containing 000000009 events
ft980721_0442_2000G300970H.fits ft980721_0442_2000G302070H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G305070H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G300670H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G301670H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G302470H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000G303470H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G304970H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G303070H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G303270H.fits-> Ignoring the following files containing 000000007 events
ft980721_0442_2000G302770H.fits-> Ignoring the following files containing 000000006 events
ft980721_0442_2000G300570H.fits-> Ignoring the following files containing 000000006 events
ft980721_0442_2000G301770H.fits-> Ignoring the following files containing 000000005 events
ft980721_0442_2000G303670H.fits-> Ignoring the following files containing 000000004 events
ft980721_0442_2000G302670H.fits-> Ignoring the following files containing 000000004 events
ft980721_0442_2000G302870H.fits-> Ignoring the following files containing 000000004 events
ft980721_0442_2000G303870H.fits-> Ignoring the following files containing 000000003 events
ft980721_0442_2000G304170H.fits-> Ignoring the following files containing 000000002 events
ft980721_0442_2000G302270H.fits-> Ignoring the following files containing 000000002 events
ft980721_0442_2000G303970H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 15 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 12 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 11 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 1 photon cnt = 16 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 11 photon cnt = 26510 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 1 photon cnt = 38 SIS0SORTSPLIT:LO:s000701h.prelist merge count = 1 photon cnt = 35 SIS0SORTSPLIT:LO:s000801h.prelist merge count = 6 photon cnt = 19608 SIS0SORTSPLIT:LO:s000901l.prelist merge count = 7 photon cnt = 1454 SIS0SORTSPLIT:LO:s001001l.prelist merge count = 4 photon cnt = 10282 SIS0SORTSPLIT:LO:s001101l.prelist merge count = 2 photon cnt = 62 SIS0SORTSPLIT:LO:s001201l.prelist merge count = 1 photon cnt = 8 SIS0SORTSPLIT:LO:s001301m.prelist merge count = 6 photon cnt = 34042 SIS0SORTSPLIT:LO:s001401m.prelist merge count = 6 photon cnt = 44411 SIS0SORTSPLIT:LO:s001501m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:Total filenames split = 50 SIS0SORTSPLIT:LO:Total split file cnt = 15 SIS0SORTSPLIT:LO:End program-> Creating ad86068000s000101m.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S000601M.fits 2 -- ft980721_0442_2000S001001M.fits 3 -- ft980721_0442_2000S002401M.fits 4 -- ft980721_0442_2000S002601M.fits 5 -- ft980721_0442_2000S003201M.fits 6 -- ft980721_0442_2000S005501M.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S000601M.fits 2 -- ft980721_0442_2000S001001M.fits 3 -- ft980721_0442_2000S002401M.fits 4 -- ft980721_0442_2000S002601M.fits 5 -- ft980721_0442_2000S003201M.fits 6 -- ft980721_0442_2000S005501M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s000201m.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S000101M.fits 2 -- ft980721_0442_2000S003101M.fits 3 -- ft980721_0442_2000S003601M.fits 4 -- ft980721_0442_2000S004201M.fits 5 -- ft980721_0442_2000S004801M.fits 6 -- ft980721_0442_2000S005401M.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S000101M.fits 2 -- ft980721_0442_2000S003101M.fits 3 -- ft980721_0442_2000S003601M.fits 4 -- ft980721_0442_2000S004201M.fits 5 -- ft980721_0442_2000S004801M.fits 6 -- ft980721_0442_2000S005401M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s000301h.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S000201H.fits 2 -- ft980721_0442_2000S000401H.fits 3 -- ft980721_0442_2000S000801H.fits 4 -- ft980721_0442_2000S001201H.fits 5 -- ft980721_0442_2000S001401H.fits 6 -- ft980721_0442_2000S001601H.fits 7 -- ft980721_0442_2000S001801H.fits 8 -- ft980721_0442_2000S002001H.fits 9 -- ft980721_0442_2000S002201H.fits 10 -- ft980721_0442_2000S002801H.fits 11 -- ft980721_0442_2000S003001H.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S000201H.fits 2 -- ft980721_0442_2000S000401H.fits 3 -- ft980721_0442_2000S000801H.fits 4 -- ft980721_0442_2000S001201H.fits 5 -- ft980721_0442_2000S001401H.fits 6 -- ft980721_0442_2000S001601H.fits 7 -- ft980721_0442_2000S001801H.fits 8 -- ft980721_0442_2000S002001H.fits 9 -- ft980721_0442_2000S002201H.fits 10 -- ft980721_0442_2000S002801H.fits 11 -- ft980721_0442_2000S003001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s000401h.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S000501H.fits 2 -- ft980721_0442_2000S000701H.fits 3 -- ft980721_0442_2000S000901H.fits 4 -- ft980721_0442_2000S001101H.fits 5 -- ft980721_0442_2000S002301H.fits 6 -- ft980721_0442_2000S002701H.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S000501H.fits 2 -- ft980721_0442_2000S000701H.fits 3 -- ft980721_0442_2000S000901H.fits 4 -- ft980721_0442_2000S001101H.fits 5 -- ft980721_0442_2000S002301H.fits 6 -- ft980721_0442_2000S002701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s000501l.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S003301L.fits 2 -- ft980721_0442_2000S003801L.fits 3 -- ft980721_0442_2000S004401L.fits 4 -- ft980721_0442_2000S005001L.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S003301L.fits 2 -- ft980721_0442_2000S003801L.fits 3 -- ft980721_0442_2000S004401L.fits 4 -- ft980721_0442_2000S005001L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s000601l.unf
---- cmerge: version 1.6 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S003501L.fits 2 -- ft980721_0442_2000S003701L.fits 3 -- ft980721_0442_2000S004101L.fits 4 -- ft980721_0442_2000S004301L.fits 5 -- ft980721_0442_2000S004701L.fits 6 -- ft980721_0442_2000S004901L.fits 7 -- ft980721_0442_2000S005301L.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S003501L.fits 2 -- ft980721_0442_2000S003701L.fits 3 -- ft980721_0442_2000S004101L.fits 4 -- ft980721_0442_2000S004301L.fits 5 -- ft980721_0442_2000S004701L.fits 6 -- ft980721_0442_2000S004901L.fits 7 -- ft980721_0442_2000S005301L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000062 events
ft980721_0442_2000S004001L.fits ft980721_0442_2000S004601L.fits-> Ignoring the following files containing 000000038 events
ft980721_0442_2000S001301H.fits-> Ignoring the following files containing 000000035 events
ft980721_0442_2000S000301H.fits-> Ignoring the following files containing 000000032 events
ft980721_0442_2000S002501M.fits-> Ignoring the following files containing 000000016 events
ft980721_0442_2000S002101H.fits-> Ignoring the following files containing 000000015 events
ft980721_0442_2000S001901H.fits-> Ignoring the following files containing 000000012 events
ft980721_0442_2000S001501H.fits-> Ignoring the following files containing 000000011 events
ft980721_0442_2000S001701H.fits-> Ignoring the following files containing 000000008 events
ft980721_0442_2000S003401L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 17 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 23 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 13 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 7 photon cnt = 56174 SIS1SORTSPLIT:LO:s100501l.prelist merge count = 8 photon cnt = 12056 SIS1SORTSPLIT:LO:s100601l.prelist merge count = 3 photon cnt = 72 SIS1SORTSPLIT:LO:s100701m.prelist merge count = 10 photon cnt = 102899 SIS1SORTSPLIT:LO:s100801m.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:Total filenames split = 32 SIS1SORTSPLIT:LO:Total split file cnt = 8 SIS1SORTSPLIT:LO:End program-> Creating ad86068000s100101m.unf
---- cmerge: version 1.6 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S100101M.fits 2 -- ft980721_0442_2000S100301M.fits 3 -- ft980721_0442_2000S100501M.fits 4 -- ft980721_0442_2000S101201M.fits 5 -- ft980721_0442_2000S101401M.fits 6 -- ft980721_0442_2000S101801M.fits 7 -- ft980721_0442_2000S102201M.fits 8 -- ft980721_0442_2000S102601M.fits 9 -- ft980721_0442_2000S103001M.fits 10 -- ft980721_0442_2000S103401M.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S100101M.fits 2 -- ft980721_0442_2000S100301M.fits 3 -- ft980721_0442_2000S100501M.fits 4 -- ft980721_0442_2000S101201M.fits 5 -- ft980721_0442_2000S101401M.fits 6 -- ft980721_0442_2000S101801M.fits 7 -- ft980721_0442_2000S102201M.fits 8 -- ft980721_0442_2000S102601M.fits 9 -- ft980721_0442_2000S103001M.fits 10 -- ft980721_0442_2000S103401M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s100201h.unf
---- cmerge: version 1.6 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S100201H.fits 2 -- ft980721_0442_2000S100401H.fits 3 -- ft980721_0442_2000S100601H.fits 4 -- ft980721_0442_2000S100801H.fits 5 -- ft980721_0442_2000S101101H.fits 6 -- ft980721_0442_2000S101501H.fits 7 -- ft980721_0442_2000S101701H.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S100201H.fits 2 -- ft980721_0442_2000S100401H.fits 3 -- ft980721_0442_2000S100601H.fits 4 -- ft980721_0442_2000S100801H.fits 5 -- ft980721_0442_2000S101101H.fits 6 -- ft980721_0442_2000S101501H.fits 7 -- ft980721_0442_2000S101701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad86068000s100301l.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft980721_0442_2000S101901L.fits 2 -- ft980721_0442_2000S102101L.fits 3 -- ft980721_0442_2000S102301L.fits 4 -- ft980721_0442_2000S102501L.fits 5 -- ft980721_0442_2000S102701L.fits 6 -- ft980721_0442_2000S102901L.fits 7 -- ft980721_0442_2000S103101L.fits 8 -- ft980721_0442_2000S103301L.fits Merging binary extension #: 2 1 -- ft980721_0442_2000S101901L.fits 2 -- ft980721_0442_2000S102101L.fits 3 -- ft980721_0442_2000S102301L.fits 4 -- ft980721_0442_2000S102501L.fits 5 -- ft980721_0442_2000S102701L.fits 6 -- ft980721_0442_2000S102901L.fits 7 -- ft980721_0442_2000S103101L.fits 8 -- ft980721_0442_2000S103301L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000072 events
ft980721_0442_2000S102001L.fits ft980721_0442_2000S102401L.fits ft980721_0442_2000S102801L.fits-> Ignoring the following files containing 000000032 events
ft980721_0442_2000S101301M.fits-> Ignoring the following files containing 000000023 events
ft980721_0442_2000S100701H.fits-> Ignoring the following files containing 000000017 events
ft980721_0442_2000S100901H.fits-> Ignoring the following files containing 000000013 events
ft980721_0442_2000S101001H.fits-> Tar-ing together the leftover raw files
a ft980721_0442_2000G200370H.fits 31K a ft980721_0442_2000G200570M.fits 31K a ft980721_0442_2000G200770H.fits 31K a ft980721_0442_2000G200870H.fits 31K a ft980721_0442_2000G200970H.fits 31K a ft980721_0442_2000G201170H.fits 31K a ft980721_0442_2000G201370M.fits 31K a ft980721_0442_2000G201670M.fits 31K a ft980721_0442_2000G201870H.fits 31K a ft980721_0442_2000G201970H.fits 31K a ft980721_0442_2000G202070H.fits 31K a ft980721_0442_2000G202270H.fits 31K a ft980721_0442_2000G202470H.fits 31K a ft980721_0442_2000G202670H.fits 31K a ft980721_0442_2000G202870H.fits 31K a ft980721_0442_2000G203070H.fits 31K a ft980721_0442_2000G203170H.fits 31K a ft980721_0442_2000G203370H.fits 31K a ft980721_0442_2000G203570H.fits 31K a ft980721_0442_2000G203770H.fits 31K a ft980721_0442_2000G203870H.fits 31K a ft980721_0442_2000G204470M.fits 31K a ft980721_0442_2000G204670H.fits 31K a ft980721_0442_2000G204770H.fits 31K a ft980721_0442_2000G204870H.fits 31K a ft980721_0442_2000G205470M.fits 34K a ft980721_0442_2000G205670L.fits 31K a ft980721_0442_2000G205870L.fits 31K a ft980721_0442_2000G206170M.fits 31K a ft980721_0442_2000G206470L.fits 31K a ft980721_0442_2000G206770M.fits 31K a ft980721_0442_2000G206970L.fits 31K a ft980721_0442_2000G207370M.fits 31K a ft980721_0442_2000G207570L.fits 31K a ft980721_0442_2000G208270M.fits 31K a ft980721_0442_2000G300370M.fits 31K a ft980721_0442_2000G300570H.fits 31K a ft980721_0442_2000G300670H.fits 31K a ft980721_0442_2000G300770H.fits 31K a ft980721_0442_2000G300970H.fits 31K a ft980721_0442_2000G301170M.fits 31K a ft980721_0442_2000G301470M.fits 31K a ft980721_0442_2000G301670H.fits 31K a ft980721_0442_2000G301770H.fits 31K a ft980721_0442_2000G301870H.fits 31K a ft980721_0442_2000G302070H.fits 31K a ft980721_0442_2000G302270H.fits 31K a ft980721_0442_2000G302470H.fits 31K a ft980721_0442_2000G302670H.fits 31K a ft980721_0442_2000G302770H.fits 31K a ft980721_0442_2000G302870H.fits 31K a ft980721_0442_2000G303070H.fits 31K a ft980721_0442_2000G303270H.fits 31K a ft980721_0442_2000G303470H.fits 31K a ft980721_0442_2000G303670H.fits 31K a ft980721_0442_2000G303870H.fits 31K a ft980721_0442_2000G303970H.fits 31K a ft980721_0442_2000G304170H.fits 31K a ft980721_0442_2000G304770M.fits 31K a ft980721_0442_2000G304970H.fits 31K a ft980721_0442_2000G305070H.fits 31K a ft980721_0442_2000G305170H.fits 31K a ft980721_0442_2000G305670M.fits 31K a ft980721_0442_2000G305870L.fits 31K a ft980721_0442_2000G306070L.fits 31K a ft980721_0442_2000G306370M.fits 31K a ft980721_0442_2000G306670L.fits 31K a ft980721_0442_2000G306970M.fits 31K a ft980721_0442_2000G307170L.fits 31K a ft980721_0442_2000G307570M.fits 31K a ft980721_0442_2000G307770L.fits 31K a ft980721_0442_2000G308470M.fits 31K a ft980721_0442_2000S000301H.fits 29K a ft980721_0442_2000S001301H.fits 29K a ft980721_0442_2000S001501H.fits 29K a ft980721_0442_2000S001701H.fits 29K a ft980721_0442_2000S001901H.fits 29K a ft980721_0442_2000S002101H.fits 29K a ft980721_0442_2000S002501M.fits 29K a ft980721_0442_2000S003401L.fits 29K a ft980721_0442_2000S004001L.fits 29K a ft980721_0442_2000S004601L.fits 29K a ft980721_0442_2000S100701H.fits 29K a ft980721_0442_2000S100901H.fits 29K a ft980721_0442_2000S101001H.fits 29K a ft980721_0442_2000S101301M.fits 29K a ft980721_0442_2000S102001L.fits 29K a ft980721_0442_2000S102401L.fits 29K a ft980721_0442_2000S102801L.fits 29K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft980721_0442.2000' is successfully opened Data Start Time is 175149755.19 (19980721 044231) Time Margin 2.0 sec included Sync error detected in 74 th SF Sync error detected in 164 th SF Sync error detected in 383 th SF Sync error detected in 808 th SF Sync error detected in 1548 th SF Sync error detected in 2046 th SF Sync error detected in 3508 th SF Sync error detected in 3701 th SF Sync error detected in 3702 th SF Sync error detected in 3703 th SF Sync error detected in 3704 th SF Sync error detected in 3705 th SF Sync error detected in 3706 th SF Sync error detected in 3707 th SF Sync error detected in 3708 th SF Sync error detected in 3710 th SF Sync error detected in 3711 th SF Sync error detected in 3712 th SF Sync error detected in 3713 th SF Sync error detected in 3718 th SF Sync error detected in 3720 th SF Sync error detected in 3722 th SF Sync error detected in 3725 th SF Sync error detected in 3728 th SF Sync error detected in 3731 th SF Sync error detected in 3738 th SF Sync error detected in 3739 th SF Sync error detected in 3740 th SF Sync error detected in 3742 th SF Sync error detected in 3743 th SF Sync error detected in 3744 th SF Sync error detected in 3745 th SF Sync error detected in 3746 th SF Sync error detected in 3747 th SF Sync error detected in 3748 th SF Sync error detected in 3752 th SF Sync error detected in 3757 th SF Sync error detected in 3799 th SF Sync error detected in 3841 th SF Sync error detected in 3855 th SF Sync error detected in 3861 th SF Sync error detected in 3862 th SF Sync error detected in 3863 th SF Sync error detected in 3867 th SF Sync error detected in 3868 th SF Sync error detected in 3869 th SF Sync error detected in 3870 th SF Sync error detected in 3871 th SF Sync error detected in 3875 th SF Sync error detected in 3876 th SF Sync error detected in 3877 th SF Sync error detected in 3878 th SF Sync error detected in 3879 th SF Sync error detected in 3881 th SF Sync error detected in 3882 th SF Sync error detected in 3884 th SF Sync error detected in 3888 th SF Sync error detected in 3892 th SF Sync error detected in 3893 th SF Sync error detected in 3898 th SF Sync error detected in 3899 th SF Sync error detected in 3905 th SF Sync error detected in 3909 th SF Sync error detected in 3927 th SF Sync error detected in 3964 th SF Sync error detected in 3980 th SF Sync error detected in 3984 th SF Sync error detected in 3992 th SF Sync error detected in 3994 th SF Sync error detected in 3995 th SF Sync error detected in 3997 th SF Sync error detected in 3998 th SF Sync error detected in 4000 th SF Sync error detected in 4003 th SF Sync error detected in 4004 th SF Sync error detected in 4006 th SF Sync error detected in 4007 th SF Sync error detected in 4008 th SF Sync error detected in 4009 th SF Sync error detected in 4010 th SF Sync error detected in 4015 th SF Sync error detected in 4016 th SF Sync error detected in 4017 th SF Sync error detected in 4018 th SF Sync error detected in 4023 th SF Sync error detected in 4024 th SF Sync error detected in 4030 th SF Sync error detected in 4031 th SF Sync error detected in 4036 th SF Sync error detected in 4037 th SF Sync error detected in 4044 th SF Sync error detected in 4045 th SF Sync error detected in 4050 th SF Sync error detected in 4051 th SF Sync error detected in 4052 th SF Sync error detected in 4058 th SF Sync error detected in 4065 th SF Sync error detected in 4072 th SF Sync error detected in 4079 th SF Sync error detected in 4080 th SF Sync error detected in 4087 th SF Sync error detected in 4093 th SF Sync error detected in 4096 th SF Sync error detected in 4100 th SF Sync error detected in 4101 th SF Sync error detected in 4105 th SF Sync error detected in 4106 th SF Sync error detected in 4109 th SF Sync error detected in 4110 th SF Sync error detected in 4111 th SF Sync error detected in 4112 th SF Sync error detected in 4115 th SF Sync error detected in 4116 th SF Sync error detected in 4118 th SF Sync error detected in 4120 th SF Sync error detected in 4125 th SF Sync error detected in 4126 th SF Sync error detected in 4127 th SF Sync error detected in 4129 th SF Sync error detected in 4130 th SF Sync error detected in 4131 th SF Sync error detected in 4132 th SF Sync error detected in 6017 th SF Sync error detected in 6038 th SF 'ft980721_0442.2000' EOF detected, sf=7518 Data End Time is 175204831.02 (19980721 200027) Gain History is written in ft980721_0442_2000.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft980721_0442_2000.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft980721_0442_2000.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft980721_0442_2000CMHK.fits
The sum of the selected column is 30224.000 The mean of the selected column is 105.31010 The standard deviation of the selected column is 1.0163019 The minimum of selected column is 104.00000 The maximum of selected column is 108.00000 The number of points used in calculation is 287-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 30224.000 The mean of the selected column is 105.31010 The standard deviation of the selected column is 1.0163019 The minimum of selected column is 104.00000 The maximum of selected column is 108.00000 The number of points used in calculation is 287
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000g200270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000g300170m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000g300270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000s000101m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000301h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000302h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000312h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000401h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000402h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000412h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s000501l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000s000601l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000s100101m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100102m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100112m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100201h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100202h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100212h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175163030.64601 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175174582.61063 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 175177401.10228 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad86068000s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad86068000s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)
S0-HK file: ft980721_0442_2000S0HK.fits
S1-HK file: ft980721_0442_2000S1HK.fits
G2-HK file: ft980721_0442_2000G2HK.fits
G3-HK file: ft980721_0442_2000G3HK.fits
Date and time are: 1998-07-21 04:41:49 mjd=51015.195708
Orbit file name is ./frf.orbit.241
Epoch of Orbital Elements: 1998-07-20 18:59:59
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa980721_0442.2000
output FITS File: ft980721_0442_2000.mkf
mkfilter2: Warning, faQparam error: time= 1.751496611869e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 1.751496931869e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 1.751497251869e+08 outside range of attitude file
Euler angles undefined for this bin
Total 1725 Data bins were processed.
-> Checking if column TIME in ft980721_0442_2000.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 7184.3345 The mean of the selected column is 20.294730 The standard deviation of the selected column is 5.8584945 The minimum of selected column is 9.1250277 The maximum of selected column is 45.218891 The number of points used in calculation is 354-> Calculating statistics for S0_PIXL2
The sum of the selected column is 8537.2137 The mean of the selected column is 23.583463 The standard deviation of the selected column is 7.0518367 The minimum of selected column is 9.7812805 The maximum of selected column is 48.250149 The number of points used in calculation is 362-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>2.7 && S0_PIXL1<37.8 )&& (S0_PIXL2>2.4 && S0_PIXL2<44.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad86068000s000212m.unf into ad86068000s000212m.evt
The sum of the selected column is 7184.3345 The mean of the selected column is 20.294730 The standard deviation of the selected column is 5.8584945 The minimum of selected column is 9.1250277 The maximum of selected column is 45.218891 The number of points used in calculation is 354-> Calculating statistics for S0_PIXL2
The sum of the selected column is 8537.2137 The mean of the selected column is 23.583463 The standard deviation of the selected column is 7.0518367 The minimum of selected column is 9.7812805 The maximum of selected column is 48.250149 The number of points used in calculation is 362-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>2.7 && S0_PIXL1<37.8 )&& (S0_PIXL2>2.4 && S0_PIXL2<44.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad86068000s000301h.unf because of mode
The sum of the selected column is 5763.9607 The mean of the selected column is 22.692759 The standard deviation of the selected column is 9.5383982 The minimum of selected column is 4.3215246 The maximum of selected column is 94.906548 The number of points used in calculation is 254-> Calculating statistics for S0_PIXL2
The sum of the selected column is 6462.2143 The mean of the selected column is 25.542349 The standard deviation of the selected column is 9.8823152 The minimum of selected column is 2.6406772 The maximum of selected column is 72.906479 The number of points used in calculation is 253-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<51.3 )&& (S0_PIXL2>0 && S0_PIXL2<55.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad86068000s000312h.unf into ad86068000s000312h.evt
The sum of the selected column is 5763.9607 The mean of the selected column is 22.692759 The standard deviation of the selected column is 9.5383982 The minimum of selected column is 4.3215246 The maximum of selected column is 94.906548 The number of points used in calculation is 254-> Calculating statistics for S0_PIXL2
The sum of the selected column is 6462.2143 The mean of the selected column is 25.542349 The standard deviation of the selected column is 9.8823152 The minimum of selected column is 2.6406772 The maximum of selected column is 72.906479 The number of points used in calculation is 253-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<51.3 )&& (S0_PIXL2>0 && S0_PIXL2<55.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad86068000s000401h.unf because of mode
The sum of the selected column is 209.71939 The mean of the selected column is 29.959912 The standard deviation of the selected column is 6.4077605 The minimum of selected column is 20.406313 The maximum of selected column is 38.000114 The number of points used in calculation is 7-> Calculating statistics for S0_PIXL2
The sum of the selected column is 216.50066 The mean of the selected column is 30.928665 The standard deviation of the selected column is 11.360842 The minimum of selected column is 16.562550 The maximum of selected column is 50.468903 The number of points used in calculation is 7-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>10.7 && S0_PIXL1<49.1 )&& (S0_PIXL2>0 && S0_PIXL2<65 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad86068000s000412h.unf into ad86068000s000412h.evt
The sum of the selected column is 209.71939 The mean of the selected column is 29.959912 The standard deviation of the selected column is 6.4077605 The minimum of selected column is 20.406313 The maximum of selected column is 38.000114 The number of points used in calculation is 7-> Calculating statistics for S0_PIXL2
The sum of the selected column is 216.50066 The mean of the selected column is 30.928665 The standard deviation of the selected column is 11.360842 The minimum of selected column is 16.562550 The maximum of selected column is 50.468903 The number of points used in calculation is 7-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>10.7 && S0_PIXL1<49.1 )&& (S0_PIXL2>0 && S0_PIXL2<65 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad86068000s000501l.unf because of mode
The sum of the selected column is 10559.720 The mean of the selected column is 32.896323 The standard deviation of the selected column is 7.8319312 The minimum of selected column is 15.343797 The maximum of selected column is 64.750198 The number of points used in calculation is 321-> Calculating statistics for S1_PIXL3
The sum of the selected column is 10910.065 The mean of the selected column is 33.364112 The standard deviation of the selected column is 8.8394577 The minimum of selected column is 17.875053 The maximum of selected column is 66.468956 The number of points used in calculation is 327-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>9.4 && S1_PIXL0<56.3 )&& (S1_PIXL3>6.8 && S1_PIXL3<59.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad86068000s100112m.unf into ad86068000s100112m.evt
The sum of the selected column is 10559.720 The mean of the selected column is 32.896323 The standard deviation of the selected column is 7.8319312 The minimum of selected column is 15.343797 The maximum of selected column is 64.750198 The number of points used in calculation is 321-> Calculating statistics for S1_PIXL3
The sum of the selected column is 10910.065 The mean of the selected column is 33.364112 The standard deviation of the selected column is 8.8394577 The minimum of selected column is 17.875053 The maximum of selected column is 66.468956 The number of points used in calculation is 327-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>9.4 && S1_PIXL0<56.3 )&& (S1_PIXL3>6.8 && S1_PIXL3<59.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad86068000s100201h.unf because of mode
The sum of the selected column is 9808.0115 The mean of the selected column is 37.292819 The standard deviation of the selected column is 14.509758 The minimum of selected column is 1.5877399 The maximum of selected column is 97.125298 The number of points used in calculation is 263-> Calculating statistics for S1_PIXL3
The sum of the selected column is 10003.297 The mean of the selected column is 38.035349 The standard deviation of the selected column is 12.894066 The minimum of selected column is 6.4904103 The maximum of selected column is 84.500259 The number of points used in calculation is 263-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0 && S1_PIXL0<80.8 )&& (S1_PIXL3>0 && S1_PIXL3<76.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Filtering ad86068000s100212h.unf into ad86068000s100212h.evt
The sum of the selected column is 9808.0115 The mean of the selected column is 37.292819 The standard deviation of the selected column is 14.509758 The minimum of selected column is 1.5877399 The maximum of selected column is 97.125298 The number of points used in calculation is 263-> Calculating statistics for S1_PIXL3
The sum of the selected column is 10003.297 The mean of the selected column is 38.035349 The standard deviation of the selected column is 12.894066 The minimum of selected column is 6.4904103 The maximum of selected column is 84.500259 The number of points used in calculation is 263-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0 && S1_PIXL0<80.8 )&& (S1_PIXL3>0 && S1_PIXL3<76.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Skipping ad86068000s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&&(S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad86068000s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&&(S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Deleting ad86068000s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad86068000g200270h.unf into ad86068000g200270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad86068000g200370l.unf into ad86068000g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Deleting ad86068000g200370l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad86068000g300270h.unf into ad86068000g300270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad86068000g300370l.unf into ad86068000g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Deleting ad86068000g300370l.evt since it contains 0 events
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad86068000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1442
Mean RA/DEC/ROLL : 247.5405 39.5810 47.1442
Pnt RA/DEC/ROLL : 247.4330 39.5499 47.1442
Image rebin factor : 1
Attitude Records : 28772
GTI intervals : 13
Total GTI (secs) : 12096.481
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1856.09 1856.09
20 Percent Complete: Total/live time: 2572.08 2572.08
30 Percent Complete: Total/live time: 8556.18 8556.18
40 Percent Complete: Total/live time: 8556.18 8556.18
50 Percent Complete: Total/live time: 8568.18 8568.18
60 Percent Complete: Total/live time: 8568.18 8568.18
70 Percent Complete: Total/live time: 10824.32 10824.32
80 Percent Complete: Total/live time: 10824.32 10824.32
90 Percent Complete: Total/live time: 11436.32 11436.32
100 Percent Complete: Total/live time: 12096.48 12096.48
Number of attitude steps used: 23
Number of attitude steps avail: 4064
Mean RA/DEC pixel offset: -13.1875 -3.5570
writing expo file: ad86068000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000g200170m.evt
ASCAEXPO_V0.9b
reading data file: ad86068000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1439
Mean RA/DEC/ROLL : 247.5394 39.5810 47.1439
Pnt RA/DEC/ROLL : 247.4858 39.5566 47.1439
Image rebin factor : 1
Attitude Records : 28772
GTI intervals : 59
Total GTI (secs) : 7546.141
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2095.99 2095.99
20 Percent Complete: Total/live time: 2095.99 2095.99
30 Percent Complete: Total/live time: 2676.03 2676.03
40 Percent Complete: Total/live time: 4119.49 4119.49
50 Percent Complete: Total/live time: 4119.49 4119.49
60 Percent Complete: Total/live time: 4672.03 4672.03
70 Percent Complete: Total/live time: 5649.57 5649.57
80 Percent Complete: Total/live time: 7058.14 7058.14
90 Percent Complete: Total/live time: 7058.14 7058.14
100 Percent Complete: Total/live time: 7546.14 7546.14
Number of attitude steps used: 27
Number of attitude steps avail: 20326
Mean RA/DEC pixel offset: -12.5165 -3.4029
writing expo file: ad86068000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000g200270h.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad86068000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1289
Mean RA/DEC/ROLL : 247.5163 39.5645 47.1289
Pnt RA/DEC/ROLL : 247.4571 39.5664 47.1289
Image rebin factor : 1
Attitude Records : 28772
GTI intervals : 13
Total GTI (secs) : 12096.481
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1856.09 1856.09
20 Percent Complete: Total/live time: 2572.08 2572.08
30 Percent Complete: Total/live time: 8556.18 8556.18
40 Percent Complete: Total/live time: 8556.18 8556.18
50 Percent Complete: Total/live time: 8568.18 8568.18
60 Percent Complete: Total/live time: 8568.18 8568.18
70 Percent Complete: Total/live time: 10824.32 10824.32
80 Percent Complete: Total/live time: 10824.32 10824.32
90 Percent Complete: Total/live time: 11436.32 11436.32
100 Percent Complete: Total/live time: 12096.48 12096.48
Number of attitude steps used: 23
Number of attitude steps avail: 4064
Mean RA/DEC pixel offset: -1.6340 -2.4093
writing expo file: ad86068000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000g300170m.evt
ASCAEXPO_V0.9b
reading data file: ad86068000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1286
Mean RA/DEC/ROLL : 247.5152 39.5645 47.1286
Pnt RA/DEC/ROLL : 247.5100 39.5730 47.1286
Image rebin factor : 1
Attitude Records : 28772
GTI intervals : 60
Total GTI (secs) : 7546.251
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2095.99 2095.99
20 Percent Complete: Total/live time: 2095.99 2095.99
30 Percent Complete: Total/live time: 2676.03 2676.03
40 Percent Complete: Total/live time: 4119.49 4119.49
50 Percent Complete: Total/live time: 4119.49 4119.49
60 Percent Complete: Total/live time: 4670.14 4670.14
70 Percent Complete: Total/live time: 5649.68 5649.68
80 Percent Complete: Total/live time: 7058.25 7058.25
90 Percent Complete: Total/live time: 7058.25 7058.25
100 Percent Complete: Total/live time: 7546.25 7546.25
Number of attitude steps used: 27
Number of attitude steps avail: 20326
Mean RA/DEC pixel offset: -0.8852 -2.2475
writing expo file: ad86068000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000g300270h.evt
ASCAEXPO_V0.9b
reading data file: ad86068000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1457
Mean RA/DEC/ROLL : 247.5434 39.5624 47.1457
Pnt RA/DEC/ROLL : 247.4305 39.5686 47.1457
Image rebin factor : 4
Attitude Records : 28772
Hot Pixels : 18
GTI intervals : 41
Total GTI (secs) : 10938.215
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1490.12 1490.12
20 Percent Complete: Total/live time: 2946.11 2946.11
30 Percent Complete: Total/live time: 7846.07 7846.07
40 Percent Complete: Total/live time: 7846.07 7846.07
50 Percent Complete: Total/live time: 7858.07 7858.07
60 Percent Complete: Total/live time: 7858.07 7858.07
70 Percent Complete: Total/live time: 9986.05 9986.05
80 Percent Complete: Total/live time: 9986.05 9986.05
90 Percent Complete: Total/live time: 10522.21 10522.21
100 Percent Complete: Total/live time: 10938.21 10938.21
Number of attitude steps used: 20
Number of attitude steps avail: 4066
Mean RA/DEC pixel offset: -70.1092 -94.0452
writing expo file: ad86068000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000s000202m.evt
ASCAEXPO_V0.9b
reading data file: ad86068000s000302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1455
Mean RA/DEC/ROLL : 247.5417 39.5623 47.1455
Pnt RA/DEC/ROLL : 247.4839 39.5739 47.1455
Image rebin factor : 4
Attitude Records : 28772
Hot Pixels : 16
GTI intervals : 64
Total GTI (secs) : 8100.675
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1822.48 1822.48
20 Percent Complete: Total/live time: 1822.48 1822.48
30 Percent Complete: Total/live time: 3871.62 3871.62
40 Percent Complete: Total/live time: 3871.62 3871.62
50 Percent Complete: Total/live time: 4168.62 4168.62
60 Percent Complete: Total/live time: 4968.14 4968.14
70 Percent Complete: Total/live time: 5887.82 5887.82
80 Percent Complete: Total/live time: 6856.82 6856.82
90 Percent Complete: Total/live time: 7464.31 7464.31
100 Percent Complete: Total/live time: 8100.67 8100.67
Number of attitude steps used: 37
Number of attitude steps avail: 21771
Mean RA/DEC pixel offset: -61.4232 -93.8904
writing expo file: ad86068000s000302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000s000302h.evt
ASCAEXPO_V0.9b
reading data file: ad86068000s000402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1453
Mean RA/DEC/ROLL : 247.5422 39.5620 47.1453
Pnt RA/DEC/ROLL : 247.4825 39.5747 47.1453
Image rebin factor : 4
Attitude Records : 28772
Hot Pixels : 11
GTI intervals : 4
Total GTI (secs) : 225.806
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 92.00 92.00
20 Percent Complete: Total/live time: 92.00 92.00
30 Percent Complete: Total/live time: 92.47 92.47
40 Percent Complete: Total/live time: 156.00 156.00
50 Percent Complete: Total/live time: 156.00 156.00
60 Percent Complete: Total/live time: 225.81 225.81
100 Percent Complete: Total/live time: 225.81 225.81
Number of attitude steps used: 5
Number of attitude steps avail: 6357
Mean RA/DEC pixel offset: -52.2837 -76.9060
writing expo file: ad86068000s000402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000s000402h.evt
ASCAEXPO_V0.9b
reading data file: ad86068000s100102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1367
Mean RA/DEC/ROLL : 247.5289 39.5739 47.1367
Pnt RA/DEC/ROLL : 247.4448 39.5571 47.1367
Image rebin factor : 4
Attitude Records : 28772
Hot Pixels : 42
GTI intervals : 80
Total GTI (secs) : 9018.215
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1530.22 1530.22
20 Percent Complete: Total/live time: 2086.11 2086.11
30 Percent Complete: Total/live time: 6618.22 6618.22
40 Percent Complete: Total/live time: 6618.22 6618.22
50 Percent Complete: Total/live time: 6650.22 6650.22
60 Percent Complete: Total/live time: 6650.22 6650.22
70 Percent Complete: Total/live time: 8226.05 8226.05
80 Percent Complete: Total/live time: 8226.05 8226.05
90 Percent Complete: Total/live time: 8646.05 8646.05
100 Percent Complete: Total/live time: 9018.22 9018.22
Number of attitude steps used: 21
Number of attitude steps avail: 3986
Mean RA/DEC pixel offset: -73.1608 -25.5161
writing expo file: ad86068000s100102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000s100102m.evt
ASCAEXPO_V0.9b
reading data file: ad86068000s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa980721_0442.2000
making an exposure map...
Aspect RA/DEC/ROLL : 247.5090 39.5664 47.1364
Mean RA/DEC/ROLL : 247.5275 39.5738 47.1364
Pnt RA/DEC/ROLL : 247.4982 39.5624 47.1364
Image rebin factor : 4
Attitude Records : 28772
Hot Pixels : 43
GTI intervals : 62
Total GTI (secs) : 8318.146
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1978.48 1978.48
20 Percent Complete: Total/live time: 1978.48 1978.48
30 Percent Complete: Total/live time: 2640.00 2640.00
40 Percent Complete: Total/live time: 4089.96 4089.96
50 Percent Complete: Total/live time: 4404.46 4404.46
60 Percent Complete: Total/live time: 5177.62 5177.62
70 Percent Complete: Total/live time: 6073.29 6073.29
80 Percent Complete: Total/live time: 7074.29 7074.29
90 Percent Complete: Total/live time: 7681.78 7681.78
100 Percent Complete: Total/live time: 8318.14 8318.14
Number of attitude steps used: 37
Number of attitude steps avail: 22143
Mean RA/DEC pixel offset: -65.7353 -24.0584
writing expo file: ad86068000s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad86068000s100202h.evtad86068000s000202m.expo ad86068000s000302h.expo ad86068000s000402h.expo ad86068000s100102m.expo ad86068000s100202h.expo-> Summing the following images to produce ad86068000sis32002_all.totsky
ad86068000s000202m.img ad86068000s000302h.img ad86068000s000402h.img ad86068000s100102m.img ad86068000s100202h.img-> Summing the following images to produce ad86068000sis32002_lo.totsky
ad86068000s000202m_lo.img ad86068000s000302h_lo.img ad86068000s000402h_lo.img ad86068000s100102m_lo.img ad86068000s100202h_lo.img-> Summing the following images to produce ad86068000sis32002_hi.totsky
ad86068000s000202m_hi.img ad86068000s000302h_hi.img ad86068000s000402h_hi.img ad86068000s100102m_hi.img ad86068000s100202h_hi.img-> Running XIMAGE to create ad86068000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad86068000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad86068000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 610.018 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 610 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "A2199_N1" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 July 21, 1998 Exposure: 36601 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 13309 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 29.0000 29 0 ![11]XIMAGE> exit-> Summing gis images
ad86068000g200170m.expo ad86068000g200270h.expo ad86068000g300170m.expo ad86068000g300270h.expo-> Summing the following images to produce ad86068000gis25670_all.totsky
ad86068000g200170m.img ad86068000g200270h.img ad86068000g300170m.img ad86068000g300270h.img-> Summing the following images to produce ad86068000gis25670_lo.totsky
ad86068000g200170m_lo.img ad86068000g200270h_lo.img ad86068000g300170m_lo.img ad86068000g300270h_lo.img-> Summing the following images to produce ad86068000gis25670_hi.totsky
ad86068000g200170m_hi.img ad86068000g200270h_hi.img ad86068000g300170m_hi.img ad86068000g300270h_hi.img-> Running XIMAGE to create ad86068000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad86068000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 73.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 73 min: 0 ![2]XIMAGE> read/exp_map ad86068000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 654.756 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 654 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "A2199_N1" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 July 21, 1998 Exposure: 39285.3 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 9823 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 21.0000 21 0 ![11]XIMAGE> exit
195 128 0.00138587 151 18 109.849-> Smoothing ad86068000gis25670_hi.totsky with ad86068000gis25670.totexpo
192 126 0.000571318 148 20 83.4772-> Smoothing ad86068000gis25670_lo.totsky with ad86068000gis25670.totexpo
195 128 0.000845664 151 17 136.682-> Determining extraction radii
195 128 24 T-> Sources with radius >= 2
195 128 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad86068000gis25670.src
221 102 1.5364e-05 211 100 6.06261-> Smoothing ad86068000sis32002_hi.totsky with ad86068000sis32002.totexpo
166 150 5.79014e-06 148 74 4.55433-> Smoothing ad86068000sis32002_lo.totsky with ad86068000sis32002.totexpo
229 97 1.01364e-05 220 102 7.02039-> Determining extraction radii
221 102 100 T-> Sources with radius >= 2
221 102 100 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad86068000sis32002.src
The sum of the selected column is 210180.00 The mean of the selected column is 942.51121 The standard deviation of the selected column is 51.670636 The minimum of selected column is 847.00000 The maximum of selected column is 1044.0000 The number of points used in calculation is 223-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 130719.00 The mean of the selected column is 586.18386 The standard deviation of the selected column is 29.301282 The minimum of selected column is 509.00000 The maximum of selected column is 630.00000 The number of points used in calculation is 223-> Converting (884.0,408.0,2.0) to s1 detector coordinates
The sum of the selected column is 122345.00 The mean of the selected column is 941.11538 The standard deviation of the selected column is 50.789066 The minimum of selected column is 858.00000 The maximum of selected column is 1036.0000 The number of points used in calculation is 130-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 77762.000 The mean of the selected column is 598.16923 The standard deviation of the selected column is 18.774112 The minimum of selected column is 553.00000 The maximum of selected column is 627.00000 The number of points used in calculation is 130-> Converting (195.0,128.0,2.0) to g2 detector coordinates
The sum of the selected column is 64537.000 The mean of the selected column is 168.06510 The standard deviation of the selected column is 1.1911032 The minimum of selected column is 165.00000 The maximum of selected column is 170.00000 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 67155.000 The mean of the selected column is 174.88281 The standard deviation of the selected column is 1.1168383 The minimum of selected column is 173.00000 The maximum of selected column is 177.00000 The number of points used in calculation is 384-> Converting (195.0,128.0,2.0) to g3 detector coordinates
The sum of the selected column is 66808.000 The mean of the selected column is 173.97917 The standard deviation of the selected column is 1.1400991 The minimum of selected column is 171.00000 The maximum of selected column is 176.00000 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 67332.000 The mean of the selected column is 175.34375 The standard deviation of the selected column is 1.0822868 The minimum of selected column is 173.00000 The maximum of selected column is 177.00000 The number of points used in calculation is 384
1 ad86068000s000202m.evt 2661 1 ad86068000s000302h.evt 2661 2 ad86068000s000402h.evt 35-> Fetching SIS0_NOTCHIP0.1
ad86068000s000202m.evt ad86068000s000302h.evt-> Grouping ad86068000s010102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 19039. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.12521 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 27 are grouped by a factor 11 ... 28 - 29 are grouped by a factor 2 ... 30 - 32 are grouped by a factor 3 ... 33 - 36 are grouped by a factor 2 ... 37 - 37 are single channels ... 38 - 57 are grouped by a factor 2 ... 58 - 63 are grouped by a factor 3 ... 64 - 65 are grouped by a factor 2 ... 66 - 73 are grouped by a factor 4 ... 74 - 79 are grouped by a factor 6 ... 80 - 88 are grouped by a factor 9 ... 89 - 94 are grouped by a factor 6 ... 95 - 108 are grouped by a factor 7 ... 109 - 128 are grouped by a factor 10 ... 129 - 139 are grouped by a factor 11 ... 140 - 151 are grouped by a factor 12 ... 152 - 169 are grouped by a factor 18 ... 170 - 191 are grouped by a factor 22 ... 192 - 226 are grouped by a factor 35 ... 227 - 294 are grouped by a factor 68 ... 295 - 511 are grouped by a factor 217 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000s010102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1 2
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Fetching SIS0_NOTCHIP1.1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data files: ecd = ./sis0c2p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.115060240963855 rmf2.tmp 0.884939759036145-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
1.151E-01 * rmf1.tmp
8.849E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.12
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf2.tmp 0.88
ASCA SIS0 NONE NONE PI
-> Generating ad86068000s010102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 100 by 74 bins
expanded to 100 by 74 bins
First WMAP bin is at detector pixel 544 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 9.0178 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.63900E+03
Weighted mean angle from optical axis = 6.307 arcmin
-> Standard Output From STOOL group_event_files:1 ad86068000s000212m.evt 2862 1 ad86068000s000312h.evt 2862 2 ad86068000s000412h.evt 37-> SIS0_NOTCHIP0.1 already present in current directory
ad86068000s000212m.evt ad86068000s000312h.evt-> Grouping ad86068000s010212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 19039. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.12521 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 55 are grouped by a factor 24 ... 56 - 58 are grouped by a factor 3 ... 59 - 63 are grouped by a factor 5 ... 64 - 67 are grouped by a factor 4 ... 68 - 76 are grouped by a factor 3 ... 77 - 84 are grouped by a factor 4 ... 85 - 90 are grouped by a factor 3 ... 91 - 98 are grouped by a factor 4 ... 99 - 107 are grouped by a factor 3 ... 108 - 115 are grouped by a factor 4 ... 116 - 120 are grouped by a factor 5 ... 121 - 128 are grouped by a factor 4 ... 129 - 133 are grouped by a factor 5 ... 134 - 139 are grouped by a factor 6 ... 140 - 146 are grouped by a factor 7 ... 147 - 157 are grouped by a factor 11 ... 158 - 172 are grouped by a factor 15 ... 173 - 182 are grouped by a factor 10 ... 183 - 195 are grouped by a factor 13 ... 196 - 243 are grouped by a factor 16 ... 244 - 266 are grouped by a factor 23 ... 267 - 285 are grouped by a factor 19 ... 286 - 310 are grouped by a factor 25 ... 311 - 340 are grouped by a factor 30 ... 341 - 386 are grouped by a factor 46 ... 387 - 450 are grouped by a factor 64 ... 451 - 521 are grouped by a factor 71 ... 522 - 679 are grouped by a factor 158 ... 680 - 965 are grouped by a factor 286 ... 966 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000s010212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1 2
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS0_NOTCHIP1.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data files: ecd = ./sis0c2p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.115362971299944 rmf2.tmp 0.884637028700056-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
1.154E-01 * rmf1.tmp
8.846E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.12
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf2.tmp 0.88
ASCA SIS0 NONE NONE PI
-> Generating ad86068000s010212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 100 by 74 bins
expanded to 100 by 74 bins
First WMAP bin is at detector pixel 544 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 9.0178 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.75600E+03
Weighted mean angle from optical axis = 6.311 arcmin
-> Standard Output From STOOL group_event_files:1 ad86068000s100102m.evt 1942 1 ad86068000s100202h.evt 1942-> Fetching SIS1_NOTCHIP1.1
ad86068000s100102m.evt ad86068000s100202h.evt-> Grouping ad86068000s110102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 17336. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.12324 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 30 are grouped by a factor 14 ... 31 - 34 are grouped by a factor 4 ... 35 - 46 are grouped by a factor 3 ... 47 - 48 are grouped by a factor 2 ... 49 - 54 are grouped by a factor 3 ... 55 - 58 are grouped by a factor 4 ... 59 - 61 are grouped by a factor 3 ... 62 - 65 are grouped by a factor 4 ... 66 - 83 are grouped by a factor 6 ... 84 - 92 are grouped by a factor 9 ... 93 - 102 are grouped by a factor 10 ... 103 - 141 are grouped by a factor 13 ... 142 - 163 are grouped by a factor 22 ... 164 - 187 are grouped by a factor 24 ... 188 - 222 are grouped by a factor 35 ... 223 - 268 are grouped by a factor 46 ... 269 - 356 are grouped by a factor 88 ... 357 - 511 are grouped by a factor 155 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000s110102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.873927958833619 rmf3.tmp 0.126072041166381-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
8.739E-01 * rmf0.tmp
1.261E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.87
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf3.tmp 0.13
ASCA SIS1 NONE NONE PI
-> Generating ad86068000s110102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 100 by 75 bins
expanded to 100 by 75 bins
First WMAP bin is at detector pixel 544 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 8.8758 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.15400E+03
Weighted mean angle from optical axis = 10.195 arcmin
-> Standard Output From STOOL group_event_files:1 ad86068000s100112m.evt 2082 1 ad86068000s100212h.evt 2082-> SIS1_NOTCHIP1.1 already present in current directory
ad86068000s100112m.evt ad86068000s100212h.evt-> Grouping ad86068000s110212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 17336. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.12324 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 60 are grouped by a factor 28 ... 61 - 67 are grouped by a factor 7 ... 68 - 73 are grouped by a factor 6 ... 74 - 78 are grouped by a factor 5 ... 79 - 82 are grouped by a factor 4 ... 83 - 92 are grouped by a factor 5 ... 93 - 96 are grouped by a factor 4 ... 97 - 102 are grouped by a factor 6 ... 103 - 107 are grouped by a factor 5 ... 108 - 114 are grouped by a factor 7 ... 115 - 120 are grouped by a factor 6 ... 121 - 127 are grouped by a factor 7 ... 128 - 138 are grouped by a factor 11 ... 139 - 168 are grouped by a factor 10 ... 169 - 187 are grouped by a factor 19 ... 188 - 204 are grouped by a factor 17 ... 205 - 252 are grouped by a factor 24 ... 253 - 275 are grouped by a factor 23 ... 276 - 308 are grouped by a factor 33 ... 309 - 345 are grouped by a factor 37 ... 346 - 395 are grouped by a factor 50 ... 396 - 477 are grouped by a factor 82 ... 478 - 551 are grouped by a factor 74 ... 552 - 739 are grouped by a factor 188 ... 740 - 959 are grouped by a factor 220 ... 960 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000s110212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 0 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data files: ecd = ./sis1c0p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.873397435897436 rmf3.tmp 0.126602564102564-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.11 20 February 1998.
Summing ...
8.734E-01 * rmf0.tmp
1.266E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.87
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf3.tmp 0.13
ASCA SIS1 NONE NONE PI
-> Generating ad86068000s110212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 100 by 75 bins
expanded to 100 by 75 bins
First WMAP bin is at detector pixel 544 216
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 8.8758 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.23300E+03
Weighted mean angle from optical axis = 10.189 arcmin
-> Standard Output From STOOL group_event_files:1 ad86068000g200170m.evt 31846 1 ad86068000g200270h.evt 31846-> GIS2_REGION256.4 already present in current directory
ad86068000g200170m.evt ad86068000g200270h.evt-> Correcting ad86068000g210170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86068000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 19643. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.76642E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 26 are grouped by a factor 27 ... 27 - 30 are grouped by a factor 4 ... 31 - 51 are grouped by a factor 3 ... 52 - 53 are grouped by a factor 2 ... 54 - 56 are grouped by a factor 3 ... 57 - 64 are grouped by a factor 2 ... 65 - 66 are single channels ... 67 - 68 are grouped by a factor 2 ... 69 - 197 are single channels ... 198 - 201 are grouped by a factor 2 ... 202 - 202 are single channels ... 203 - 224 are grouped by a factor 2 ... 225 - 225 are single channels ... 226 - 287 are grouped by a factor 2 ... 288 - 290 are grouped by a factor 3 ... 291 - 294 are grouped by a factor 2 ... 295 - 300 are grouped by a factor 3 ... 301 - 312 are grouped by a factor 2 ... 313 - 318 are grouped by a factor 3 ... 319 - 320 are grouped by a factor 2 ... 321 - 323 are grouped by a factor 3 ... 324 - 327 are grouped by a factor 2 ... 328 - 345 are grouped by a factor 3 ... 346 - 349 are grouped by a factor 4 ... 350 - 358 are grouped by a factor 3 ... 359 - 362 are grouped by a factor 4 ... 363 - 365 are grouped by a factor 3 ... 366 - 373 are grouped by a factor 4 ... 374 - 379 are grouped by a factor 3 ... 380 - 387 are grouped by a factor 4 ... 388 - 392 are grouped by a factor 5 ... 393 - 396 are grouped by a factor 4 ... 397 - 406 are grouped by a factor 5 ... 407 - 410 are grouped by a factor 4 ... 411 - 415 are grouped by a factor 5 ... 416 - 423 are grouped by a factor 4 ... 424 - 430 are grouped by a factor 7 ... 431 - 435 are grouped by a factor 5 ... 436 - 441 are grouped by a factor 6 ... 442 - 449 are grouped by a factor 8 ... 450 - 456 are grouped by a factor 7 ... 457 - 464 are grouped by a factor 8 ... 465 - 476 are grouped by a factor 6 ... 477 - 483 are grouped by a factor 7 ... 484 - 493 are grouped by a factor 10 ... 494 - 502 are grouped by a factor 9 ... 503 - 510 are grouped by a factor 8 ... 511 - 520 are grouped by a factor 10 ... 521 - 529 are grouped by a factor 9 ... 530 - 536 are grouped by a factor 7 ... 537 - 544 are grouped by a factor 8 ... 545 - 551 are grouped by a factor 7 ... 552 - 559 are grouped by a factor 8 ... 560 - 572 are grouped by a factor 13 ... 573 - 582 are grouped by a factor 10 ... 583 - 602 are grouped by a factor 20 ... 603 - 625 are grouped by a factor 23 ... 626 - 649 are grouped by a factor 24 ... 650 - 677 are grouped by a factor 28 ... 678 - 721 are grouped by a factor 44 ... 722 - 810 are grouped by a factor 89 ... 811 - 1023 are grouped by a factor 213 ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000g210170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 46 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 105 111
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 109.34 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.75480E+04
Weighted mean angle from optical axis = 14.035 arcmin
-> Standard Output From STOOL group_event_files:1 ad86068000g300170m.evt 28407 1 ad86068000g300270h.evt 28407-> GIS3_REGION256.4 already present in current directory
ad86068000g300170m.evt ad86068000g300270h.evt-> Correcting ad86068000g310170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad86068000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 19643. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.88849E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 24 are grouped by a factor 25 ... 25 - 29 are grouped by a factor 5 ... 30 - 32 are grouped by a factor 3 ... 33 - 37 are grouped by a factor 5 ... 38 - 45 are grouped by a factor 4 ... 46 - 57 are grouped by a factor 3 ... 58 - 71 are grouped by a factor 2 ... 72 - 184 are single channels ... 185 - 186 are grouped by a factor 2 ... 187 - 188 are single channels ... 189 - 190 are grouped by a factor 2 ... 191 - 191 are single channels ... 192 - 193 are grouped by a factor 2 ... 194 - 195 are single channels ... 196 - 233 are grouped by a factor 2 ... 234 - 236 are grouped by a factor 3 ... 237 - 254 are grouped by a factor 2 ... 255 - 260 are grouped by a factor 3 ... 261 - 276 are grouped by a factor 2 ... 277 - 282 are grouped by a factor 3 ... 283 - 286 are grouped by a factor 2 ... 287 - 292 are grouped by a factor 3 ... 293 - 294 are grouped by a factor 2 ... 295 - 303 are grouped by a factor 3 ... 304 - 305 are grouped by a factor 2 ... 306 - 317 are grouped by a factor 3 ... 318 - 322 are grouped by a factor 5 ... 323 - 330 are grouped by a factor 4 ... 331 - 333 are grouped by a factor 3 ... 334 - 337 are grouped by a factor 4 ... 338 - 340 are grouped by a factor 3 ... 341 - 348 are grouped by a factor 4 ... 349 - 353 are grouped by a factor 5 ... 354 - 357 are grouped by a factor 4 ... 358 - 362 are grouped by a factor 5 ... 363 - 366 are grouped by a factor 4 ... 367 - 378 are grouped by a factor 6 ... 379 - 382 are grouped by a factor 4 ... 383 - 412 are grouped by a factor 5 ... 413 - 430 are grouped by a factor 6 ... 431 - 438 are grouped by a factor 8 ... 439 - 445 are grouped by a factor 7 ... 446 - 461 are grouped by a factor 8 ... 462 - 468 are grouped by a factor 7 ... 469 - 476 are grouped by a factor 8 ... 477 - 485 are grouped by a factor 9 ... 486 - 493 are grouped by a factor 8 ... 494 - 505 are grouped by a factor 12 ... 506 - 516 are grouped by a factor 11 ... 517 - 524 are grouped by a factor 8 ... 525 - 542 are grouped by a factor 9 ... 543 - 552 are grouped by a factor 10 ... 553 - 560 are grouped by a factor 8 ... 561 - 572 are grouped by a factor 12 ... 573 - 591 are grouped by a factor 19 ... 592 - 612 are grouped by a factor 21 ... 613 - 639 are grouped by a factor 27 ... 640 - 675 are grouped by a factor 36 ... 676 - 713 are grouped by a factor 38 ... 714 - 791 are grouped by a factor 78 ... 792 - 951 are grouped by a factor 160 ... 952 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad86068000g310170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 48 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 111 112
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.17 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.45260E+04
Weighted mean angle from optical axis = 16.560 arcmin
-> Plotting ad86068000g210170_1_pi.ps from ad86068000g210170_1.pi
XSPEC 9.01 22:22:35 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000g210170_1.pi
Net count rate (cts/s) for file 1 0.8961 +/- 6.7543E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86068000g310170_1_pi.ps from ad86068000g310170_1.pi
XSPEC 9.01 22:22:48 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000g310170_1.pi
Net count rate (cts/s) for file 1 0.7421 +/- 6.1598E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86068000s010102_1_pi.ps from ad86068000s010102_1.pi
XSPEC 9.01 22:22:59 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000s010102_1.pi
Net count rate (cts/s) for file 1 8.7190E-02+/- 2.1509E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86068000s010212_1_pi.ps from ad86068000s010212_1.pi
XSPEC 9.01 22:23:12 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000s010212_1.pi
Net count rate (cts/s) for file 1 9.3335E-02+/- 2.2665E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86068000s110102_1_pi.ps from ad86068000s110102_1.pi
XSPEC 9.01 22:23:27 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000s110102_1.pi
Net count rate (cts/s) for file 1 6.7257E-02+/- 1.9840E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad86068000s110212_1_pi.ps from ad86068000s110212_1.pi
XSPEC 9.01 22:23:39 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad86068000s110212_1.pi
Net count rate (cts/s) for file 1 7.1987E-02+/- 2.1131E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86068000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A2199_N1 Start Time (d) .... 11015 04:48:13.187
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11015 19:43:41.187
No. of Rows ....... 35 Bin Time (s) ...... 557.8
Right Ascension ... 2.4751E+02 Internal time sys.. Converted to TJD
Declination ....... 3.9566E+01 Experiment ........ ASCA SIS0
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 97 Newbins of 557.750 (s)
Intv 1 Start11015 4:52:52
Ser.1 Avg 0.8994E-01 Chisq 36.40 Var 0.2054E-03 Newbs. 35
Min 0.6154E-01 Max 0.1221 expVar 0.1975E-03 Bins 35
Results from Statistical Analysis
Newbin Integration Time (s).. 557.75
Interval Duration (s)........ 52986.
No. of Newbins .............. 35
Average (c/s) ............... 0.89936E-01 +/- 0.24E-02
Standard Deviation (c/s)..... 0.14333E-01
Minimum (c/s)................ 0.61536E-01
Maximum (c/s)................ 0.12213
Variance ((c/s)**2).......... 0.20543E-03 +/- 0.50E-04
Expected Variance ((c/s)**2). 0.19751E-03 +/- 0.48E-04
Third Moment ((c/s)**3)...... 0.60806E-06
Average Deviation (c/s)...... 0.11283E-01
Skewness..................... 0.20652 +/- 0.41
Kurtosis.....................-0.28773 +/- 0.83
RMS fractional variation....< 0.14366 (3 sigma)
Chi-Square................... 36.403 dof 34
Chi-Square Prob of constancy. 0.35748 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.27975 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 97 Newbins of 557.750 (s)
Intv 1 Start11015 4:52:52
Ser.1 Avg 0.8994E-01 Chisq 36.40 Var 0.2054E-03 Newbs. 35
Min 0.6154E-01 Max 0.1221 expVar 0.1975E-03 Bins 35
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86068000s000002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=8.0000000000E+00 for ad86068000s100102m.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86068000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A2199_N1 Start Time (d) .... 11015 04:48:13.187
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11015 19:43:41.187
No. of Rows ....... 26 Bin Time (s) ...... 724.8
Right Ascension ... 2.4751E+02 Internal time sys.. Converted to TJD
Declination ....... 3.9566E+01 Experiment ........ ASCA SIS1
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 75 Newbins of 724.764 (s)
Intv 1 Start11015 4:54:15
Ser.1 Avg 0.6998E-01 Chisq 32.35 Var 0.1641E-03 Newbs. 26
Min 0.3790E-01 Max 0.9388E-01expVar 0.1319E-03 Bins 26
Results from Statistical Analysis
Newbin Integration Time (s).. 724.76
Interval Duration (s)........ 52908.
No. of Newbins .............. 26
Average (c/s) ............... 0.69977E-01 +/- 0.23E-02
Standard Deviation (c/s)..... 0.12810E-01
Minimum (c/s)................ 0.37904E-01
Maximum (c/s)................ 0.93882E-01
Variance ((c/s)**2).......... 0.16409E-03 +/- 0.46E-04
Expected Variance ((c/s)**2). 0.13188E-03 +/- 0.37E-04
Third Moment ((c/s)**3)......-0.34079E-06
Average Deviation (c/s)...... 0.95791E-02
Skewness.....................-0.16213 +/- 0.48
Kurtosis..................... 0.29884 +/- 0.96
RMS fractional variation....< 0.14858 (3 sigma)
Chi-Square................... 32.348 dof 25
Chi-Square Prob of constancy. 0.14820 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.10864E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 75 Newbins of 724.764 (s)
Intv 1 Start11015 4:54:15
Ser.1 Avg 0.6998E-01 Chisq 32.35 Var 0.1641E-03 Newbs. 26
Min 0.3790E-01 Max 0.9388E-01expVar 0.1319E-03 Bins 26
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86068000s100002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad86068000g200170m.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86068000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A2199_N1 Start Time (d) .... 11015 04:48:13.187
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11015 19:45:17.187
No. of Rows ....... 350 Bin Time (s) ...... 55.80
Right Ascension ... 2.4751E+02 Internal time sys.. Converted to TJD
Declination ....... 3.9566E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 105.248 (s)
Intv 1 Start11015 4:49: 5
Ser.1 Avg 0.8976 Chisq 184.9 Var 0.1078E-01 Newbs. 199
Min 0.5073 Max 1.210 expVar 0.1050E-01 Bins 350
Results from Statistical Analysis
Newbin Integration Time (s).. 105.25
Interval Duration (s)........ 53782.
No. of Newbins .............. 199
Average (c/s) ............... 0.89762 +/- 0.73E-02
Standard Deviation (c/s)..... 0.10382
Minimum (c/s)................ 0.50731
Maximum (c/s)................ 1.2098
Variance ((c/s)**2).......... 0.10780E-01 +/- 0.11E-02
Expected Variance ((c/s)**2). 0.10495E-01 +/- 0.11E-02
Third Moment ((c/s)**3)...... 0.70596E-04
Average Deviation (c/s)...... 0.82290E-01
Skewness..................... 0.63079E-01 +/- 0.17
Kurtosis..................... 0.61231 +/- 0.35
RMS fractional variation....< 0.62660E-01 (3 sigma)
Chi-Square................... 184.94 dof 198
Chi-Square Prob of constancy. 0.73820 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.30849E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 105.248 (s)
Intv 1 Start11015 4:49: 5
Ser.1 Avg 0.8976 Chisq 184.9 Var 0.1078E-01 Newbs. 199
Min 0.5073 Max 1.210 expVar 0.1050E-01 Bins 350
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86068000g200070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad86068000g300170m.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad86068000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A2199_N1 Start Time (d) .... 11015 04:48:13.187
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 11015 19:45:17.187
No. of Rows ....... 301 Bin Time (s) ...... 67.38
Right Ascension ... 2.4751E+02 Internal time sys.. Converted to TJD
Declination ....... 3.9566E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 105.248 (s)
Intv 1 Start11015 4:49: 5
Ser.1 Avg 0.7391 Chisq 174.0 Var 0.9868E-02 Newbs. 198
Min 0.4152 Max 1.033 expVar 0.8913E-02 Bins 301
Results from Statistical Analysis
Newbin Integration Time (s).. 105.25
Interval Duration (s)........ 53782.
No. of Newbins .............. 198
Average (c/s) ............... 0.73911 +/- 0.67E-02
Standard Deviation (c/s)..... 0.99339E-01
Minimum (c/s)................ 0.41522
Maximum (c/s)................ 1.0325
Variance ((c/s)**2).......... 0.98683E-02 +/- 0.99E-03
Expected Variance ((c/s)**2). 0.89133E-02 +/- 0.90E-03
Third Moment ((c/s)**3)......-0.22079E-03
Average Deviation (c/s)...... 0.77581E-01
Skewness.....................-0.22522 +/- 0.17
Kurtosis..................... 0.67066 +/- 0.35
RMS fractional variation....< 0.60239E-01 (3 sigma)
Chi-Square................... 173.98 dof 197
Chi-Square Prob of constancy. 0.87982 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.60326 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 105.248 (s)
Intv 1 Start11015 4:49: 5
Ser.1 Avg 0.7391 Chisq 174.0 Var 0.9868E-02 Newbs. 198
Min 0.4152 Max 1.033 expVar 0.8913E-02 Bins 301
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad86068000g300070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad86068000g200170m.evt[2] ad86068000g200270h.evt[2]-> Making L1 light curve of ft980721_0442_2000G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 22030 output records from 22089 good input G2_L1 records.-> Making L1 light curve of ft980721_0442_2000G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 19073 output records from 33894 good input G2_L1 records.-> Merging GTIs from the following files:
ad86068000g300170m.evt[2] ad86068000g300270h.evt[2]-> Making L1 light curve of ft980721_0442_2000G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 20111 output records from 20171 good input G3_L1 records.-> Making L1 light curve of ft980721_0442_2000G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 18829 output records from 31821 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 7518 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft980721_0442_2000.mkf
1 ad86068000g200170m.unf 68114 1 ad86068000g200270h.unf 68114 1 ad86068000g200370l.unf 68114-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 22:38:07 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad86068000g220170.cal
Net count rate (cts/s) for file 1 0.1757 +/- 2.3005E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.6693E+06 using 84 PHA bins.
Reduced chi-squared = 2.1680E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.6609E+06 using 84 PHA bins.
Reduced chi-squared = 2.1293E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.6609E+06 using 84 PHA bins.
Reduced chi-squared = 2.1024E+04
!XSPEC> renorm
Chi-Squared = 927.6 using 84 PHA bins.
Reduced chi-squared = 11.74
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
766.02 0 1.000 5.896 0.1006 3.8191E-02
3.5288E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
502.41 0 1.000 5.885 0.1551 4.8822E-02
3.1928E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
348.61 -1 1.000 5.941 0.1936 6.5069E-02
2.3427E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
306.06 -2 1.000 6.013 0.2250 7.8486E-02
1.3338E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
304.18 -3 1.000 5.995 0.2133 7.5996E-02
1.5730E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
303.98 -4 1.000 6.001 0.2157 7.6854E-02
1.4859E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
303.93 -5 1.000 5.998 0.2139 7.6503E-02
1.5207E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
303.92 -6 1.000 5.999 0.2142 7.6616E-02
1.5095E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.99895 +/- 0.11440E-01
3 3 2 gaussian/b Sigma 0.214200 +/- 0.11477E-01
4 4 2 gaussian/b norm 7.661623E-02 +/- 0.22043E-02
5 2 3 gaussian/b LineE 6.60488 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.224758 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.509453E-02 +/- 0.17172E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 303.9 using 84 PHA bins.
Reduced chi-squared = 3.847
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad86068000g220170.cal peaks at 5.99895 +/- 0.01144 keV1 ad86068000g300170m.unf 61145 1 ad86068000g300270h.unf 61145 1 ad86068000g300370l.unf 61145-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 22:38:43 9-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad86068000g320170.cal
Net count rate (cts/s) for file 1 0.1205 +/- 1.9079E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.2258E+06 using 84 PHA bins.
Reduced chi-squared = 2.8906E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.2119E+06 using 84 PHA bins.
Reduced chi-squared = 2.8358E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.2119E+06 using 84 PHA bins.
Reduced chi-squared = 2.7999E+04
!XSPEC> renorm
Chi-Squared = 1177. using 84 PHA bins.
Reduced chi-squared = 14.90
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
950.07 0 1.000 5.893 9.5628E-02 3.1175E-02
2.6730E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
372.31 0 1.000 5.866 0.1460 4.9438E-02
2.2895E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
151.47 -1 1.000 5.912 0.1597 7.1018E-02
1.4408E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
144.35 -2 1.000 5.921 0.1589 7.5054E-02
1.2340E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
143.99 -3 1.000 5.917 0.1541 7.4566E-02
1.2853E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
143.98 -4 1.000 5.918 0.1548 7.4742E-02
1.2679E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
143.97 -5 1.000 5.918 0.1545 7.4690E-02
1.2730E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.91783 +/- 0.80137E-02
3 3 2 gaussian/b Sigma 0.154465 +/- 0.97248E-02
4 4 2 gaussian/b norm 7.469017E-02 +/- 0.18099E-02
5 2 3 gaussian/b LineE 6.51557 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.162078 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.273008E-02 +/- 0.11615E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 144.0 using 84 PHA bins.
Reduced chi-squared = 1.822
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad86068000g320170.cal peaks at 5.91783 +/- 0.0080137 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s000402h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 129
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 7 72
cleaning chip # 2
Hot pixels & counts : 4 28
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 129
Number of image cts rejected (N, %) : 10077.52
By chip : 0 1 2 3
Pixels rejected : 0 7 4 0
Image counts : 0 97 32 0
Image cts rejected: 0 72 28 0
Image cts rej (%) : 0.00 74.23 87.50 0.00
filtering data...
Total counts : 0 97 32 0
Total cts rejected: 0 72 28 0
Total cts rej (%) : 0.00 74.23 87.50 0.00
Number of clean counts accepted : 29
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s000412h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s000412h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 138
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 7 74
cleaning chip # 2
Hot pixels & counts : 4 29
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 138
Number of image cts rejected (N, %) : 10374.64
By chip : 0 1 2 3
Pixels rejected : 0 7 4 0
Image counts : 0 102 36 0
Image cts rejected: 0 74 29 0
Image cts rej (%) : 0.00 72.55 80.56 0.00
filtering data...
Total counts : 0 102 36 0
Total cts rejected: 0 74 29 0
Total cts rej (%) : 0.00 72.55 80.56 0.00
Number of clean counts accepted : 35
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100102m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100102m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1114
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 16 554
Flickering pixels iter, pixels & cnts : 1 5 23
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 13 450
Flickering pixels iter, pixels & cnts : 1 4 20
Number of pixels rejected : 38
Number of (internal) image counts : 1114
Number of image cts rejected (N, %) : 104793.99
By chip : 0 1 2 3
Pixels rejected : 21 0 0 17
Image counts : 612 0 0 502
Image cts rejected: 577 0 0 470
Image cts rej (%) : 94.28 0.00 0.00 93.63
filtering data...
Total counts : 612 0 0 502
Total cts rejected: 577 0 0 470
Total cts rej (%) : 94.28 0.00 0.00 93.63
Number of clean counts accepted : 67
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 38
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100112m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100112m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1119
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 16 555
Flickering pixels iter, pixels & cnts : 1 5 23
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 13 452
Flickering pixels iter, pixels & cnts : 1 4 20
Number of pixels rejected : 38
Number of (internal) image counts : 1119
Number of image cts rejected (N, %) : 105093.83
By chip : 0 1 2 3
Pixels rejected : 21 0 0 17
Image counts : 613 0 0 506
Image cts rejected: 578 0 0 472
Image cts rej (%) : 94.29 0.00 0.00 93.28
filtering data...
Total counts : 613 0 0 506
Total cts rejected: 578 0 0 472
Total cts rej (%) : 94.29 0.00 0.00 93.28
Number of clean counts accepted : 69
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 38
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 414
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 15 188
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 12 175
Flickering pixels iter, pixels & cnts : 1 2 8
Number of pixels rejected : 30
Number of (internal) image counts : 414
Number of image cts rejected (N, %) : 37490.34
By chip : 0 1 2 3
Pixels rejected : 16 0 0 14
Image counts : 211 0 0 203
Image cts rejected: 191 0 0 183
Image cts rej (%) : 90.52 0.00 0.00 90.15
filtering data...
Total counts : 211 0 0 203
Total cts rejected: 191 0 0 183
Total cts rej (%) : 90.52 0.00 0.00 90.15
Number of clean counts accepted : 40
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 30
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 416
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 15 188
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 12 175
Flickering pixels iter, pixels & cnts : 1 2 8
Number of pixels rejected : 30
Number of (internal) image counts : 416
Number of image cts rejected (N, %) : 37489.90
By chip : 0 1 2 3
Pixels rejected : 16 0 0 14
Image counts : 212 0 0 204
Image cts rejected: 191 0 0 183
Image cts rej (%) : 90.09 0.00 0.00 89.71
filtering data...
Total counts : 212 0 0 204
Total cts rejected: 191 0 0 183
Total cts rej (%) : 90.09 0.00 0.00 89.71
Number of clean counts accepted : 42
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 30
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 884
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 403
Flickering pixels iter, pixels & cnts : 1 4 26
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 414
Flickering pixels iter, pixels & cnts : 1 1 4
Number of pixels rejected : 27
Number of (internal) image counts : 884
Number of image cts rejected (N, %) : 84795.81
By chip : 0 1 2 3
Pixels rejected : 15 0 0 12
Image counts : 441 0 0 443
Image cts rejected: 429 0 0 418
Image cts rej (%) : 97.28 0.00 0.00 94.36
filtering data...
Total counts : 441 0 0 443
Total cts rejected: 429 0 0 418
Total cts rej (%) : 97.28 0.00 0.00 94.36
Number of clean counts accepted : 37
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 27
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad86068000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 884
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 403
Flickering pixels iter, pixels & cnts : 1 4 26
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 414
Flickering pixels iter, pixels & cnts : 1 1 4
Number of pixels rejected : 27
Number of (internal) image counts : 884
Number of image cts rejected (N, %) : 84795.81
By chip : 0 1 2 3
Pixels rejected : 15 0 0 12
Image counts : 441 0 0 443
Image cts rejected: 429 0 0 418
Image cts rej (%) : 97.28 0.00 0.00 94.36
filtering data...
Total counts : 441 0 0 443
Total cts rejected: 429 0 0 418
Total cts rej (%) : 97.28 0.00 0.00 94.36
Number of clean counts accepted : 37
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 27
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad86068000g200170m.unfOffset of 208224004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-08-08 00:00:00.00000 Modified Julian Day = 51398.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
ad86068000s000302h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad86068000s000402h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad86068000s000302h.unf
ad86068000s000312h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad86068000s000412h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad86068000s000312h.unf
ad86068000s000301h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad86068000s000401h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad86068000s000301h.unf
ad86068000s000101m.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad86068000s000201m.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad86068000s000101m.unf
ad86068000s000501l.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad86068000s000601l.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad86068000s000501l.unf
77 622 1901 610 3709 3900 4386 610 6192 1492 6217 672 6219 152 6220 96 8
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files