Processing Job Log for Sequence 10010060, version 015

This is the complete and detailed record of how this sequence was processed.

The following information is also available:

Processing started (15:25:21)

Checking input files for validity (15:25:23)

-> Verifying the input files
-> FITS file fa930407_2237.0053 exists
-> FITS file ad10010060_input.cat exists
-> FITS file ft930407_2237.0053 exists
-> Calculating Observation start and end times
-> Fetching leapsec.fits from /aps/calibration
-> leapsec.fits is already present in the working directory
-> Observation begins 8.3758225E+06 = 1993-04-07 22:37:02
-> Observation ends 8.3839885E+06 = 1993-04-08 00:53:08

Determine nominal pointing (15:25:29)

-> Checking fa930407_2237.0053 for problems
-> Fetching asca_mean_1999-04-23.fits from /aps/calibration
-> stdout output from aspect
Spacecraft Euler Angles: Phi=83.86108 Theta=67.88009 Psi=-178.04004
Telescope pointing: R.A.=83.59489 Dec=21.97874 Roll=92.05989 degrees
-> Nominal spacecraft Euler angles: Phi=83.861084607484 Theta=67.880089314661 Psi=-178.04004142587
-> Nominal telescope pointing: R.A.=83.594893095361 Dec=21.978738034104 Roll Angle=92.059888333654
-> Galactic Coordinates: Lii=184.568752 Bii=-5.833414

Running frfread on telemetry files (15:25:36)

-> Running frfread on ft930407_2237.0053
-> stdout output from frfread4
55.9998 second gap between superframes 106 and 107
Dropped 1st C0 read after clocking change in ft930407_2237_0053S000702H.fits
Dropped 1st C3 read after clocking change in ft930407_2237_0053S101502H.fits
Dropped 1st C0 read after clocking change in ft930407_2237_0053S101902M.fits
Dropped 1st C1 read after clocking change in ft930407_2237_0053S101902M.fits
Dropped 1st C2 read after clocking change in ft930407_2237_0053S101902M.fits
Dropped 1st C3 read after clocking change in ft930407_2237_0053S101902M.fits
Dropped 1st C1 read after clocking change in ft930407_2237_0053S001301M.fits
Dropped 1st C2 read after clocking change in ft930407_2237_0053S001301M.fits
Dropped 1st C3 read after clocking change in ft930407_2237_0053S001301M.fits
Dropped 1st C0 read after clocking change in ft930407_2237_0053S001301M.fits
Dropping SF 2111 with inconsistent datamode 0/31
Dropping SF 2112 with inconsistent datamode 0/2
2273 of 2275 super frames processed
-> 0% of superframes in ft930407_2237.0053 corrupted
-> Deleting the following files with NEVENTS=0
ft930407_2237_0053G200170M.fits
ft930407_2237_0053G200270M.fits
ft930407_2237_0053G200370H.fits
ft930407_2237_0053G200470H.fits
ft930407_2237_0053G201270H.fits
ft930407_2237_0053G201370H.fits
ft930407_2237_0053G201470M.fits
ft930407_2237_0053G201570M.fits
ft930407_2237_0053G201670M.fits
ft930407_2237_0053G201770M.fits
ft930407_2237_0053G201870H.fits
ft930407_2237_0053G201970H.fits
ft930407_2237_0053G202070H.fits
ft930407_2237_0053G202170H.fits
ft930407_2237_0053G202270H.fits
ft930407_2237_0053G300170M.fits
ft930407_2237_0053G300270M.fits
ft930407_2237_0053G300370H.fits
ft930407_2237_0053G300470H.fits
ft930407_2237_0053G301270H.fits
ft930407_2237_0053G301370H.fits
ft930407_2237_0053G301470M.fits
ft930407_2237_0053G301570M.fits
ft930407_2237_0053G301670M.fits
ft930407_2237_0053G301770M.fits
ft930407_2237_0053G301870H.fits
ft930407_2237_0053G301970H.fits
ft930407_2237_0053G302070H.fits
ft930407_2237_0053G302170H.fits
ft930407_2237_0053G302270H.fits
ft930407_2237_0053S000102M.fits
ft930407_2237_0053S000302H.fits
ft930407_2237_0053S000402H.fits
ft930407_2237_0053S000502H.fits
ft930407_2237_0053S000602H.fits
ft930407_2237_0053S001003M.fits
ft930407_2237_0053S001103M.fits
ft930407_2237_0053S001201M.fits
ft930407_2237_0053S001301M.fits
ft930407_2237_0053S100102M.fits
ft930407_2237_0053S101702M.fits
ft930407_2237_0053S101802M.fits
ft930407_2237_0053S101902M.fits
ft930407_2237_0053S102001M.fits
-> merging GTIs for s0 930407_2237.0053
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft930407_2237_0053S0HK.fits
-> Total ONTIME for s0 930407_2237.0053 = 4891.98
-> merging GTIs for s1 930407_2237.0053
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft930407_2237_0053S1HK.fits
-> Total ONTIME for s1 930407_2237.0053 = 5339.98
-> merging GTIs for g2 930407_2237.0053
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft930407_2237_0053G2HK.fits
-> Total ONTIME for g2 930407_2237.0053 = 3353.99
-> merging GTIs for g3 930407_2237.0053
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft930407_2237_0053G3HK.fits
-> Total ONTIME for g3 930407_2237.0053 = 3355.99

Merging event files from frfread (15:29:6)

-> Grouping s0 event files
-> stdout output from group_event_files
1 ft930407_2237_0053S000803H.fits 113354
2 ft930407_2237_0053S000903M.fits 23359
3 ft930407_2237_0053S001501H.fits 6262
4 ft930407_2237_0053S000702H.fits 3739
5 ft930407_2237_0053S000202M.fits 2499
6 ft930407_2237_0053S001401M.fits 1395
7 ft930407_2237_0053S001602H.fits 565
8 ft930407_2237_0053S001702H.fits 2
-> Checking ft930407_2237_0053S000803H.fits for validity
-> Creating ad10010060s000103h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S000803H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S000803H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S000903M.fits for validity
-> Creating ad10010060s000203m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S000903M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S000903M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S001501H.fits for validity
-> Creating ad10010060s000301h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S001501H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S001501H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S000702H.fits for validity
-> Creating ad10010060s000402h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S000702H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S000702H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S000202M.fits for validity
-> Creating ad10010060s000502m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S000202M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S000202M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S001401M.fits for validity
-> Creating ad10010060s000601m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S001401M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S001401M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 565 events ft930407_2237_0053S001602H.fits
-> Ignoring the following files containing 2 events ft930407_2237_0053S001702H.fits
-> Grouping s1 event files
-> stdout output from group_event_files
1 ft930407_2237_0053S101002H.fits 280333
1 ft930407_2237_0053S101102H.fits 280333
1 ft930407_2237_0053S101202H.fits 280333
1 ft930407_2237_0053S101302H.fits 280333
1 ft930407_2237_0053S101402H.fits 280333
1 ft930407_2237_0053S102402H.fits 280333
2 ft930407_2237_0053S101502H.fits 146140
3 ft930407_2237_0053S101602M.fits 14208
4 ft930407_2237_0053S100302H.fits 7539
4 ft930407_2237_0053S100402H.fits 7539
4 ft930407_2237_0053S100502H.fits 7539
4 ft930407_2237_0053S100602H.fits 7539
4 ft930407_2237_0053S100702H.fits 7539
4 ft930407_2237_0053S100802H.fits 7539
4 ft930407_2237_0053S100902H.fits 7539
4 ft930407_2237_0053S102302H.fits 7539
5 ft930407_2237_0053S102201H.fits 4800
6 ft930407_2237_0053S100202M.fits 2455
7 ft930407_2237_0053S102101M.fits 1570
-> Creating ad10010060s100102h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  6  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 6 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S101002H.fits 
 2 -- ft930407_2237_0053S101102H.fits 
 3 -- ft930407_2237_0053S101202H.fits 
 4 -- ft930407_2237_0053S101302H.fits 
 5 -- ft930407_2237_0053S101402H.fits 
 6 -- ft930407_2237_0053S102402H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S101002H.fits 
 2 -- ft930407_2237_0053S101102H.fits 
 3 -- ft930407_2237_0053S101202H.fits 
 4 -- ft930407_2237_0053S101302H.fits 
 5 -- ft930407_2237_0053S101402H.fits 
 6 -- ft930407_2237_0053S102402H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S101502H.fits for validity
-> Creating ad10010060s100202h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S101502H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S101502H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S101602M.fits for validity
-> Creating ad10010060s100302m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S101602M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S101602M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad10010060s100402h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  8  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 8 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S100302H.fits 
 2 -- ft930407_2237_0053S100402H.fits 
 3 -- ft930407_2237_0053S100502H.fits 
 4 -- ft930407_2237_0053S100602H.fits 
 5 -- ft930407_2237_0053S100702H.fits 
 6 -- ft930407_2237_0053S100802H.fits 
 7 -- ft930407_2237_0053S100902H.fits 
 8 -- ft930407_2237_0053S102302H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S100302H.fits 
 2 -- ft930407_2237_0053S100402H.fits 
 3 -- ft930407_2237_0053S100502H.fits 
 4 -- ft930407_2237_0053S100602H.fits 
 5 -- ft930407_2237_0053S100702H.fits 
 6 -- ft930407_2237_0053S100802H.fits 
 7 -- ft930407_2237_0053S100902H.fits 
 8 -- ft930407_2237_0053S102302H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S102201H.fits for validity
-> Creating ad10010060s100501h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S102201H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S102201H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S100202M.fits for validity
-> Creating ad10010060s100602m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S100202M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S100202M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053S102101M.fits for validity
-> Creating ad10010060s100701m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053S102101M.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053S102101M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Grouping g2 event files
-> stdout output from group_event_files
1 ft930407_2237_0053G201070H.fits 102144
2 ft930407_2237_0053G200870H.fits 98048
2 ft930407_2237_0053G202570H.fits 98048
3 ft930407_2237_0053G200970H.fits 73729
4 ft930407_2237_0053G202671H.fits 496
4 ft930407_2237_0053G202771H.fits 496
5 ft930407_2237_0053G200770H.fits 252
5 ft930407_2237_0053G202470H.fits 252
6 ft930407_2237_0053G200670H.fits 185
6 ft930407_2237_0053G202370H.fits 185
7 ft930407_2237_0053G201170H.fits 45
8 ft930407_2237_0053G200570H.fits 2
-> Checking ft930407_2237_0053G201070H.fits for validity
-> Creating ad10010060g200170h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G201070H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G201070H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad10010060g200270h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 2 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G200870H.fits 
 2 -- ft930407_2237_0053G202570H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G200870H.fits 
 2 -- ft930407_2237_0053G202570H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053G200970H.fits for validity
-> Creating ad10010060g200370h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G200970H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G200970H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 496 events ft930407_2237_0053G202671H.fits ft930407_2237_0053G202771H.fits
-> Ignoring the following files containing 252 events ft930407_2237_0053G200770H.fits ft930407_2237_0053G202470H.fits
-> Ignoring the following files containing 185 events ft930407_2237_0053G200670H.fits ft930407_2237_0053G202370H.fits
-> Ignoring the following files containing 45 events ft930407_2237_0053G201170H.fits
-> Ignoring the following files containing 2 events ft930407_2237_0053G200570H.fits
-> Grouping g3 event files
-> stdout output from group_event_files
1 ft930407_2237_0053G301070H.fits 101888
2 ft930407_2237_0053G300870H.fits 97559
2 ft930407_2237_0053G302570H.fits 97559
3 ft930407_2237_0053G300970H.fits 73983
4 ft930407_2237_0053G302671H.fits 496
4 ft930407_2237_0053G302771H.fits 496
5 ft930407_2237_0053G300670H.fits 258
5 ft930407_2237_0053G302370H.fits 258
6 ft930407_2237_0053G300770H.fits 258
6 ft930407_2237_0053G302470H.fits 258
7 ft930407_2237_0053G300570H.fits 83
8 ft930407_2237_0053G301170H.fits 45
-> Checking ft930407_2237_0053G301070H.fits for validity
-> Creating ad10010060g300170h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G301070H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G301070H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad10010060g300270h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 2 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G300870H.fits 
 2 -- ft930407_2237_0053G302570H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G300870H.fits 
 2 -- ft930407_2237_0053G302570H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Checking ft930407_2237_0053G300970H.fits for validity
-> Creating ad10010060g300370h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 1 good fits files ...
Merging binary extension #: 1 
 1 -- ft930407_2237_0053G300970H.fits 
Merging binary extension #: 2 
 1 -- ft930407_2237_0053G300970H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 496 events ft930407_2237_0053G302671H.fits ft930407_2237_0053G302771H.fits
-> Ignoring the following files containing 258 events ft930407_2237_0053G300670H.fits ft930407_2237_0053G302370H.fits
-> Ignoring the following files containing 258 events ft930407_2237_0053G300770H.fits ft930407_2237_0053G302470H.fits
-> Ignoring the following files containing 83 events ft930407_2237_0053G300570H.fits
-> Ignoring the following files containing 45 events ft930407_2237_0053G301170H.fits
-> stdout output from tar
a ft930407_2237_0053G200570H.fits 31K
a ft930407_2237_0053G200670H.fits 34K
a ft930407_2237_0053G200770H.fits 37K
a ft930407_2237_0053G201170H.fits 31K
a ft930407_2237_0053G202370H.fits 31K
a ft930407_2237_0053G202470H.fits 31K
a ft930407_2237_0053G202671H.fits 262K
a ft930407_2237_0053G202771H.fits 40K
a ft930407_2237_0053G300570H.fits 31K
a ft930407_2237_0053G300670H.fits 37K
a ft930407_2237_0053G300770H.fits 37K
a ft930407_2237_0053G301170H.fits 31K
a ft930407_2237_0053G302370H.fits 31K
a ft930407_2237_0053G302470H.fits 31K
a ft930407_2237_0053G302671H.fits 262K
a ft930407_2237_0053G302771H.fits 40K
a ft930407_2237_0053S001602H.fits 43K
a ft930407_2237_0053S001702H.fits 29K

Converting FAINT mode files to BRIGHT and BRIGHT2 modes (15:32:47)

-> Split threshold for SIS0=40, and SIS1=40
-> Fetching faintdfe.tbl
-> Calculating DFE values for ad10010060s000301h.unf with zerodef=1
-> Converting ad10010060s000301h.unf to ad10010060s000312h.unf
-> Calculating DFE values for ad10010060s000301h.unf with zerodef=2
-> Converting ad10010060s000301h.unf to ad10010060s000302h.unf
-> Calculating DFE values for ad10010060s000601m.unf with zerodef=1
-> Converting ad10010060s000601m.unf to ad10010060s000612m.unf
-> Removing ad10010060s000612m.unf since it only has 559 events
-> Calculating DFE values for ad10010060s000601m.unf with zerodef=2
-> Converting ad10010060s000601m.unf to ad10010060s000602m.unf
-> Removing ad10010060s000602m.unf since it only has 517 events
-> Calculating DFE values for ad10010060s100501h.unf with zerodef=1
-> Converting ad10010060s100501h.unf to ad10010060s100512h.unf
-> Calculating DFE values for ad10010060s100501h.unf with zerodef=2
-> Converting ad10010060s100501h.unf to ad10010060s100502h.unf
-> Calculating DFE values for ad10010060s100701m.unf with zerodef=1
-> Converting ad10010060s100701m.unf to ad10010060s100712m.unf
-> Removing ad10010060s100712m.unf since it only has 701 events
-> Calculating DFE values for ad10010060s100701m.unf with zerodef=2
-> Converting ad10010060s100701m.unf to ad10010060s100702m.unf
-> Removing ad10010060s100702m.unf since it only has 669 events

Calibrating the unfiltered event files (15:34:59)

-> Creating GIS gain history files
-> leapsec.fits is already present in the working directory
-> Fetching gis_temp2gain.fits from /aps/calibration
-> Creating Gain History File ft930407_2237_0053.ghf
-> stdout output from temp2gain
temp2gain V4.6
leapsec FITS data was successfully read

'ft930407_2237.0053' is successfully opened
Data Start Time is 8375820.61 (19930407 223700)
Time Margin 2.0 sec included
Sync error detected in 2110 th SF
'ft930407_2237.0053' EOF detected, sf=2275
Data End Time is 8383990.59 (19930408 005310)
Gain History is written in ft930407_2237_0053.ghf
-> Generating attitude correction table ad10010060_015_bp4.txt
-> Extracting info from ft930407_2237_0053CMHK.fits
-> Using BP4 between 90.1293426377139 and 98.9043652274541
-> Running ascalin on all unfiltered event files
-> Preparing to run ascalin on ad10010060g200170h.unf
-> Fetching gis2_ano_on_pow2_200494.fits from /aps/calibration
-> Running ascalin on ad10010060g200170h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060g200270h.unf
-> Fetching gis2_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad10010060g200270h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060g200370h.unf
-> gis2_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad10010060g200370h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060g300170h.unf
-> Fetching gis3_ano_on_pow2_200494.fits from /aps/calibration
-> Running ascalin on ad10010060g300170h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060g300270h.unf
-> Fetching gis3_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad10010060g300270h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060g300370h.unf
-> gis3_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad10010060g300370h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000301h.unf
-> Fetching s0_teldef_ascalin.fits from /aps/calibration
-> Fetching sisph2pi_110397.fits from /aps/calibration
-> Running ascalin on ad10010060s000301h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000302h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s000302h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000312h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s000312h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000402h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s000402h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000502m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s000502m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s000601m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s000601m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100102h.unf
-> Fetching s1_teldef_ascalin.fits from /aps/calibration
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100102h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100202h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100202h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100302m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100302m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100402h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100402h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100501h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100501h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100502h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100502h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100512h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100512h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100602m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100602m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad10010060s100701m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad10010060s100701m.unf
-> stdout output from ascalin
ASCALIN_V0.9v

Checking FAST mode files for correct CCD mode (15:40:19)

-> Checking ad10010060s000103h.unf
-> Checking ad10010060s000203m.unf

Creating filter files (15:40:34)

-> leapsec.fits is already present in the working directory
-> Fetching rigidity.data.1.23 from /aps/calibration
-> Copying orbit file /aps/orbit/frf.orbit.253 to working directory
-> Creating ft930407_2237_0053.mkf
-> stdout output from mkfilter2
 
leapsec FITS data was successfully read

S0-HK file: ft930407_2237_0053S0HK.fits

S1-HK file: ft930407_2237_0053S1HK.fits

G2-HK file: ft930407_2237_0053G2HK.fits

G3-HK file: ft930407_2237_0053G3HK.fits

Date and time are: 1993-04-07 22:36:14  mjd=49084.941836

Orbit file name is frf.orbit.253

Epoch of Orbital Elements: 1993-04-05 06:59:59

Rigidity Data File: rigidity.data.1.23

Attitude FRF: fa930407_2237.0053

output FITS File: ft930407_2237_0053.mkf

mkfilter2: Warning, faQparam error: time= 8.375726612632e+06 outside range of attitude file

           Euler angles undefined for this bin

mkfilter2: Warning, faQparam error: time= 8.375758612632e+06 outside range of attitude file

           Euler angles undefined for this bin

mkfilter2: Warning, faQparam error: time= 8.375790612632e+06 outside range of attitude file

           Euler angles undefined for this bin

Total 259 Data bins were processed.
-> Adding deadtime to ft930407_2237_0053.mkf
-> Adding ad10010060_s0.dfe to ft930407_2237_0053.mkf
-> Adding ad10010060_s1.dfe to ft930407_2237_0053.mkf
-> Plotting quantities from ft930407_2237_0053.mkf
-> Extracting telemetry corruption files

Cleaning and filtering the unfiltered event files (15:43:35)

-> Filtering ad10010060s000103h.unf into ad10010060s000103h.evt
-> Calculating statistics for S0_PIXL0
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   148.55256
 The mean of the selected column is                  2.3211337
 The standard deviation of the selected column is    1.0679958
 The minimum of selected column is                   1.2750041
 The maximum of selected column is                   9.9687824
 The number of points used in calculation is               64
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0 && S0_PIXL0<5.5 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        FAST        HIGH        1993-04-07  23:14:46    0.21E+04   113354 1000
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000103h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          14347     14320              0        27         0         0
 Writing events file
  14320 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         14347     14320              0        27         0         0
   in  1983.9     seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000103h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
Setting X and Y to RAW
 
Getting Min and Max for Energy Column...
Got min and max for PHA:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
Area discrimination is enabled.
The mask is set from    6 to    7
Only photons inside the mask are in the telemetry.
SELECT FAST is unnecessary in this case.
!screen:ASCA-SIS0-FAST > select event "grade==0"
!screen:ASCA-SIS0-FAST > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-FAST > extract events
!screen:ASCA-SIS0-FAST > save events outfile=ad10010060s000103h.evt use_events=no
Wrote events list to file ad10010060s000103h.evt
!screen:ASCA-SIS0-FAST > exit save_session=no
-> Filtering ad10010060s000203m.unf into ad10010060s000203m.evt
-> Calculating statistics for S0_PIXL0
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   18.937557
 The mean of the selected column is                  2.7053653
 The standard deviation of the selected column is    1.2571266
 The minimum of selected column is                   1.4687545
 The maximum of selected column is                   5.0625157
 The number of points used in calculation is                7
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0 && S0_PIXL0<6.4 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        FAST        MEDIUM      1993-04-07  23:50:26    0.45E+03    23359 1000
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000203m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           4299      1601              0      2698         0         0
 Writing events file
   1601 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4299      1601              0      2698         0         0
   in  188.14     seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000203m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
Setting X and Y to RAW
 
Getting Min and Max for Energy Column...
Got min and max for PHA:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
Area discrimination is enabled.
The mask is set from    6 to    7
Only photons inside the mask are in the telemetry.
SELECT FAST is unnecessary in this case.
!screen:ASCA-SIS0-FAST > select event "grade==0"
!screen:ASCA-SIS0-FAST > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-FAST > extract events
!screen:ASCA-SIS0-FAST > save events outfile=ad10010060s000203m.evt use_events=no
Wrote events list to file ad10010060s000203m.evt
!screen:ASCA-SIS0-FAST > exit save_session=no
-> Skipping ad10010060s000301h.unf because of mode
-> Filtering ad10010060s000302h.unf into ad10010060s000302h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&(S0_PIXL1>0)&&(S0_PIXL2>0)&&(S0_PIXL3>0)  )&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-08  00:26:40    0.47E+03     3433 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000302h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000302h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> Filtering ad10010060s000312h.unf into ad10010060s000312h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&(S0_PIXL1>0)&&(S0_PIXL2>0)&&(S0_PIXL3>0)  )&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT2     HIGH        1993-04-08  00:26:40    0.47E+03     3630 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000312h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000312h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS0-BRIGHT2 > Session saved, goodbye
-> Filtering ad10010060s000402h.unf into ad10010060s000402h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)  )&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:12:54    0.72E+02     3739 1000
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000402h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10010060s000402h.evt use_events=no
Wrote cleaned events file to ad10010060s000402h.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10010060s000402h.evt since it contains 0 events
-> Filtering ad10010060s000502m.unf into ad10010060s000502m.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&(S0_PIXL1>0)&&(S0_PIXL2>0)&&(S0_PIXL3>0)  )&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  22:42:52    0.75E+03     2499 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000502m.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s000502m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> Skipping ad10010060s000601m.unf because of mode
-> Filtering ad10010060s100102h.unf into ad10010060s100102h.evt
-> Calculating statistics for S1_PIXL0
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4216.1386
 The mean of the selected column is                  98.049735
 The standard deviation of the selected column is    12.387593
 The minimum of selected column is                   76.594002
 The maximum of selected column is                   138.43794
 The number of points used in calculation is               43
-> Calculating statistics for S1_PIXL1
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2764.1652
 The mean of the selected column is                  64.282911
 The standard deviation of the selected column is    12.231759
 The minimum of selected column is                   44.187645
 The maximum of selected column is                   95.250305
 The number of points used in calculation is               43
-> Calculating statistics for S1_PIXL2
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   6164.9574
 The mean of the selected column is                  146.78470
 The standard deviation of the selected column is    11.016001
 The minimum of selected column is                   127.18792
 The maximum of selected column is                   174.37556
 The number of points used in calculation is               42
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   19643.345
 The mean of the selected column is                  456.82197
 The standard deviation of the selected column is    18.146814
 The minimum of selected column is                   434.87637
 The maximum of selected column is                   544.47046
 The number of points used in calculation is               43
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>60.8 && S1_PIXL0<135.2 )&&
(S1_PIXL1>27.5 && S1_PIXL1<100.9 )&&
(S1_PIXL2>113.7 && S1_PIXL2<179.8 )&&
(S1_PIXL3>402.3 && S1_PIXL3<511.2 )  )
&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:13:00    0.18E+04   280333 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         246003    187007              0     58996         0         0
 Writing events file
 187007 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        246003    187007              0     58996         0         0
   in  1280.0     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       187007
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          48         985
cleaning chip # 1
 Hot pixels & counts                   :              11         847
 Flickering pixels iter, pixels & cnts :   1          48         795
cleaning chip # 2
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          53        1191
cleaning chip # 3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          10         147
 
 Number of pixels rejected           :          170
 Number of (internal) image counts   :       187007
 Number of image cts rejected (N, %) :         3965 2.12
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            48           59           53           10
 
 Image counts      :         46302        23848        71710        45147
 Image cts rejected:           985         1642         1191          147
 Image cts rej (%) :          2.13         6.89         1.66         0.33
 
    filtering data...
 
 Total counts      :         46302        23848        71710        45147
 Total cts rejected:           985         1642         1191          147
 Total cts rej (%) :          2.13         6.89         1.66         0.33
 
 Number of clean counts accepted  :       183042
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          170
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100102h.evt use_events=no
Wrote cleaned events file to ad10010060s100102h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad10010060s100202h.unf into ad10010060s100202h.evt
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   13063.151
 The mean of the selected column is                  687.53426
 The standard deviation of the selected column is    30.170880
 The minimum of selected column is                   567.54919
 The maximum of selected column is                   716.25226
 The number of points used in calculation is               19
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>597 && S1_PIXL3<778 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:39:26    0.66E+03   146140 0001
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         130973    113994              0     16979         0         0
 Writing events file
 113994 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        130973    113994              0     16979         0         0
   in  576.00     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       113994
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          13         422
 
 Number of pixels rejected           :           13
 Number of (internal) image counts   :       113994
 Number of image cts rejected (N, %) :          422 0.37
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           13
 
 Image counts      :             0            0            0       113994
 Image cts rejected:             0            0            0          422
 Image cts rej (%) :          0.00         0.00         0.00         0.37
 
    filtering data...
 
 Total counts      :             0            0            0       113994
 Total cts rejected:             0            0            0          422
 Total cts rej (%) :          0.00         0.00         0.00         0.37
 
 Number of clean counts accepted  :       113572
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           13
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100202h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100202h.evt use_events=no
Wrote cleaned events file to ad10010060s100202h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad10010060s100302m.unf into ad10010060s100302m.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0)  )&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  23:50:26    0.45E+03    14208 0001
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100302m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100302m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100302m.evt use_events=no
Wrote cleaned events file to ad10010060s100302m.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100302m.evt since it contains 0 events
-> Filtering ad10010060s100402h.unf into ad10010060s100402h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0)&&(S1_PIXL1>0)&&(S1_PIXL2>0)&&(S1_PIXL3>0)  )&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:05:56    0.10E+04     7539 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100402h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100402h.evt use_events=no
Wrote cleaned events file to ad10010060s100402h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100402h.evt since it contains 0 events
-> Skipping ad10010060s100501h.unf because of mode
-> Filtering ad10010060s100502h.unf into ad10010060s100502h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0)&&(S1_PIXL1>0)&&(S1_PIXL2>0)&&(S1_PIXL3>0)  )&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-08  00:26:40    0.47E+03     2624 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100502h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100502h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100502h.evt use_events=no
Wrote cleaned events file to ad10010060s100502h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100502h.evt since it contains 0 events
-> Filtering ad10010060s100512h.unf into ad10010060s100512h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0)&&(S1_PIXL1>0)&&(S1_PIXL2>0)&&(S1_PIXL3>0)  )&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT2     HIGH        1993-04-08  00:26:40    0.47E+03     2763 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100512h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100512h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad10010060s100512h.evt use_events=no
Wrote cleaned events file to ad10010060s100512h.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad10010060s100512h.evt since it contains 0 events
-> Filtering ad10010060s100602m.unf into ad10010060s100602m.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0)&&(S1_PIXL1>0)&&(S1_PIXL2>0)&&(S1_PIXL3>0)  )&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  22:42:52    0.75E+03     2455 1111
Processing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100602m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data24/seq_proc/ad0_10010060.015/screen_in_event.xs
    reading data file: /data/data24/seq_proc/ad0_10010060.015/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060s100602m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10010060s100602m.evt use_events=no
Wrote cleaned events file to ad10010060s100602m.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100602m.evt since it contains 0 events
-> Skipping ad10010060s100701m.unf because of mode
-> Filtering ad10010060g200170h.unf into ad10010060g200170h.evt
-> Fetching GIS2_REGION256_OFF.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102144     99956           2188         0         0         0
 Writing events file
  99956 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        102144     99956           2188         0         0         0
   in  798.00     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       99956               98418              1538
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10010060g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad10010060g200270h.unf into ad10010060g200270h.evt
-> GIS2_REGION256_OFF.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.17E+04    98048     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          98048     45095           3858     49095         0         0
 Writing events file
  45095 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98048     45095           3858     49095         0         0
   in  360.01     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       45095               44469               626
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g200270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10010060g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad10010060g200370h.unf into ad10010060g200370h.evt
-> GIS2_REGION256_OFF.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73729     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          73729     48314           1574     23841         0         0
 Writing events file
  48314 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         73729     48314           1574     23841         0         0
   in  385.99     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       48314               47547               767
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g200370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10010060g200370h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad10010060g300170h.unf into ad10010060g300170h.evt
-> Fetching GIS3_REGION256_OFF.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         101888     99704           2184         0         0         0
 Writing events file
  99704 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        101888     99704           2184         0         0         0
   in  796.00     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       99704               98223              1481
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10010060g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad10010060g300270h.unf into ad10010060g300270h.evt
-> GIS3_REGION256_OFF.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.17E+04    97559     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          97559     44957           3621     48981         0         0
 Writing events file
  44957 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97559     44957           3621     48981         0         0
   in  358.01     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       44957               44363               594
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g300270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10010060g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad10010060g300370h.unf into ad10010060g300370h.evt
-> GIS3_REGION256_OFF.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73983     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          73983     48675           1498     23810         0         0
 Writing events file
  48675 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         73983     48675           1498     23810         0         0
   in  387.99     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       48675               47979               696
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA > read events ad10010060g300370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.d/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10010060g300370h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no

Generating images and exposure maps (16:1:13)

-> Generating exposure map ad10010060g200170.expo
-> GIS2_REGION256_OFF.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,81)
-ELLIPSE(167.5,220,24.66,28.95,245.298)
-> gis2_ano_on_pow2_200494.fits already present in current directory
-> Running ascaexpo for ad10010060g200170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g200170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_pow2_200494.fits
    reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0621
 Mean   RA/DEC/ROLL :       83.5991      21.9991      92.0621
 Pnt    RA/DEC/ROLL :       83.5888      21.9593      92.0621
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       797.997
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        490.00       490.00
  20 Percent Complete: Total/live time:        490.00       490.00
  30 Percent Complete: Total/live time:        798.00       798.00
 100 Percent Complete: Total/live time:        798.00       798.00
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         1696
 Mean RA/DEC pixel offset:       -6.6432      -1.5306
 
    writing expo file: ad10010060g200170.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g200170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g200170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03    98418     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     98418              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98418     98418              0         0         0         0
   in  798.00     seconds
 Image            has    98418 counts for  123.3     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     51613              0         0         0     46805
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98418     51613              0         0         0     46805
   in  798.00     seconds
 Image            has    51613 counts for  64.68     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     47225              0         0         0     51193
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98418     47225              0         0         0     51193
   in  798.00     seconds
 Image            has    47225 counts for  59.18     counts/sec
 Command not found; type ? for a command listing
!ad10010060g200170h:ASCA >
!ad10010060g200170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g200170h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200170h:ASCA > read events ad10010060g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200170h:ASCA-GIS2-PH > set image sky
!ad10010060g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad10010060g200170h:ASCA-GIS2-PH > extract image
!ad10010060g200170h:ASCA-GIS2-PH > save image outfile=ad10010060g200170_all.img
Wrote image to file ad10010060g200170_all.img
!ad10010060g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10010060g200170h:ASCA-GIS2-PH > extract image
!ad10010060g200170h:ASCA-GIS2-PH > save image outfile=ad10010060g200170_lo.img
Wrote image to file ad10010060g200170_lo.img
!ad10010060g200170h:ASCA-GIS2-PH > clear pha_cut
!ad10010060g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g200170h:ASCA-GIS2-PH > extract image
!ad10010060g200170h:ASCA-GIS2-PH > save image outfile=ad10010060g200170_hi.img
Wrote image to file ad10010060g200170_hi.img
!ad10010060g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10010060g200270.expo
-> GIS2_REGION256_OFF.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad10010060g200270h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g200270h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0624
 Mean   RA/DEC/ROLL :       83.5975      21.9954      92.0624
 Pnt    RA/DEC/ROLL :       83.5906      21.9629      92.0624
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       360.007
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        332.00       332.00
  20 Percent Complete: Total/live time:        332.00       332.00
  30 Percent Complete: Total/live time:        360.01       360.01
 100 Percent Complete: Total/live time:        360.01       360.01
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:          881
 Mean RA/DEC pixel offset:       -5.3222      -0.9672
 
    writing expo file: ad10010060g200270.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g200270h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g200270h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.36E+03    44469     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     44469              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44469     44469              0         0         0         0
   in  360.01     seconds
 Image            has    44469 counts for  123.5     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     23434              0         0         0     21035
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44469     23434              0         0         0     21035
   in  360.01     seconds
 Image            has    23434 counts for  65.09     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     21228              0         0         0     23241
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44469     21228              0         0         0     23241
   in  360.01     seconds
 Image            has    21228 counts for  58.97     counts/sec
 Command not found; type ? for a command listing
!ad10010060g200270h:ASCA >
!ad10010060g200270h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g200270h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200270h:ASCA > read events ad10010060g200270h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200270h:ASCA-GIS2-PH > set image sky
!ad10010060g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad10010060g200270h:ASCA-GIS2-PH > extract image
!ad10010060g200270h:ASCA-GIS2-PH > save image outfile=ad10010060g200270_all.img
Wrote image to file ad10010060g200270_all.img
!ad10010060g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10010060g200270h:ASCA-GIS2-PH > extract image
!ad10010060g200270h:ASCA-GIS2-PH > save image outfile=ad10010060g200270_lo.img
Wrote image to file ad10010060g200270_lo.img
!ad10010060g200270h:ASCA-GIS2-PH > clear pha_cut
!ad10010060g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g200270h:ASCA-GIS2-PH > extract image
!ad10010060g200270h:ASCA-GIS2-PH > save image outfile=ad10010060g200270_hi.img
Wrote image to file ad10010060g200270_hi.img
!ad10010060g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10010060g200370.expo
-> GIS2_REGION256_OFF.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad10010060g200370h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g200370h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0616
 Mean   RA/DEC/ROLL :       83.5983      21.9972      92.0616
 Pnt    RA/DEC/ROLL :       83.5889      21.9607      92.0616
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       385.988
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        385.99       385.99
 100 Percent Complete: Total/live time:        385.99       385.99
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:          894
 Mean RA/DEC pixel offset:       -4.5775      -0.9838
 
    writing expo file: ad10010060g200370.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g200370h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g200370h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47547     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     47547              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47547     47547              0         0         0         0
   in  385.99     seconds
 Image            has    47547 counts for  123.2     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     25082              0         0         0     22465
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47547     25082              0         0         0     22465
   in  385.99     seconds
 Image            has    25082 counts for  64.98     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     22712              0         0         0     24835
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47547     22712              0         0         0     24835
   in  385.99     seconds
 Image            has    22712 counts for  58.84     counts/sec
 Command not found; type ? for a command listing
!ad10010060g200370h:ASCA >
!ad10010060g200370h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g200370h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200370h:ASCA > read events ad10010060g200370h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g200370h:ASCA-GIS2-PH > set image sky
!ad10010060g200370h:ASCA-GIS2-PH > filter region corner_point.reg
!ad10010060g200370h:ASCA-GIS2-PH > extract image
!ad10010060g200370h:ASCA-GIS2-PH > save image outfile=ad10010060g200370_all.img
Wrote image to file ad10010060g200370_all.img
!ad10010060g200370h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10010060g200370h:ASCA-GIS2-PH > extract image
!ad10010060g200370h:ASCA-GIS2-PH > save image outfile=ad10010060g200370_lo.img
Wrote image to file ad10010060g200370_lo.img
!ad10010060g200370h:ASCA-GIS2-PH > clear pha_cut
!ad10010060g200370h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g200370h:ASCA-GIS2-PH > extract image
!ad10010060g200370h:ASCA-GIS2-PH > save image outfile=ad10010060g200370_hi.img
Wrote image to file ad10010060g200370_hi.img
!ad10010060g200370h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10010060g300170.expo
-> GIS3_REGION256_OFF.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,73)
-ELLIPSE(217,95,21.56,25.92,169.216)
-> gis3_ano_on_pow2_200494.fits already present in current directory
-> Running ascaexpo for ad10010060g300170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g300170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_pow2_200494.fits
    reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0615
 Mean   RA/DEC/ROLL :       83.5974      21.9743      92.0615
 Pnt    RA/DEC/ROLL :       83.5905      21.9840      92.0615
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       795.997
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        492.00       492.00
  20 Percent Complete: Total/live time:        492.00       492.00
  30 Percent Complete: Total/live time:        796.00       796.00
 100 Percent Complete: Total/live time:        796.00       796.00
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         1692
 Mean RA/DEC pixel offset:        1.4009      -0.7412
 
    writing expo file: ad10010060g300170.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g300170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g300170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03    98223     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     98223              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98223     98223              0         0         0         0
   in  796.00     seconds
 Image            has    98223 counts for  123.4     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     51910              0         0         0     46313
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98223     51910              0         0         0     46313
   in  796.00     seconds
 Image            has    51910 counts for  65.21     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     46788              0         0         0     51435
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98223     46788              0         0         0     51435
   in  796.00     seconds
 Image            has    46788 counts for  58.78     counts/sec
 Command not found; type ? for a command listing
!ad10010060g300170h:ASCA >
!ad10010060g300170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g300170h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300170h:ASCA > read events ad10010060g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300170h:ASCA-GIS3-PH > set image sky
!ad10010060g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad10010060g300170h:ASCA-GIS3-PH > extract image
!ad10010060g300170h:ASCA-GIS3-PH > save image outfile=ad10010060g300170_all.img
Wrote image to file ad10010060g300170_all.img
!ad10010060g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10010060g300170h:ASCA-GIS3-PH > extract image
!ad10010060g300170h:ASCA-GIS3-PH > save image outfile=ad10010060g300170_lo.img
Wrote image to file ad10010060g300170_lo.img
!ad10010060g300170h:ASCA-GIS3-PH > clear pha_cut
!ad10010060g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g300170h:ASCA-GIS3-PH > extract image
!ad10010060g300170h:ASCA-GIS3-PH > save image outfile=ad10010060g300170_hi.img
Wrote image to file ad10010060g300170_hi.img
!ad10010060g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10010060g300270.expo
-> GIS3_REGION256_OFF.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad10010060g300270h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g300270h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0618
 Mean   RA/DEC/ROLL :       83.5959      21.9706      92.0618
 Pnt    RA/DEC/ROLL :       83.5922      21.9877      92.0618
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       358.007
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        330.50       330.50
  20 Percent Complete: Total/live time:        330.50       330.50
  30 Percent Complete: Total/live time:        358.01       358.01
 100 Percent Complete: Total/live time:        358.01       358.01
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:          877
 Mean RA/DEC pixel offset:        2.7207      -0.1782
 
    writing expo file: ad10010060g300270.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g300270h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g300270h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.36E+03    44363     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     44363              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44363     44363              0         0         0         0
   in  358.01     seconds
 Image            has    44363 counts for  123.9     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     23284              0         0         0     21079
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44363     23284              0         0         0     21079
   in  358.01     seconds
 Image            has    23284 counts for  65.04     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     21293              0         0         0     23070
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44363     21293              0         0         0     23070
   in  358.01     seconds
 Image            has    21293 counts for  59.48     counts/sec
 Command not found; type ? for a command listing
!ad10010060g300270h:ASCA >
!ad10010060g300270h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g300270h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300270h:ASCA > read events ad10010060g300270h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300270h:ASCA-GIS3-PH > set image sky
!ad10010060g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad10010060g300270h:ASCA-GIS3-PH > extract image
!ad10010060g300270h:ASCA-GIS3-PH > save image outfile=ad10010060g300270_all.img
Wrote image to file ad10010060g300270_all.img
!ad10010060g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10010060g300270h:ASCA-GIS3-PH > extract image
!ad10010060g300270h:ASCA-GIS3-PH > save image outfile=ad10010060g300270_lo.img
Wrote image to file ad10010060g300270_lo.img
!ad10010060g300270h:ASCA-GIS3-PH > clear pha_cut
!ad10010060g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g300270h:ASCA-GIS3-PH > extract image
!ad10010060g300270h:ASCA-GIS3-PH > save image outfile=ad10010060g300270_hi.img
Wrote image to file ad10010060g300270_hi.img
!ad10010060g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10010060g300370.expo
-> GIS3_REGION256_OFF.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad10010060g300370h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060g300370h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0611
 Mean   RA/DEC/ROLL :       83.5966      21.9724      92.0611
 Pnt    RA/DEC/ROLL :       83.5905      21.9855      92.0611
 
 Image rebin factor :             1
 Attitude Records   :          9081
 GTI intervals      :             1
 Total GTI (secs)   :       387.988
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        387.99       387.99
 100 Percent Complete: Total/live time:        387.99       387.99
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:          894
 Mean RA/DEC pixel offset:        1.4619      -0.3838
 
    writing expo file: ad10010060g300370.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060g300370h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060g300370h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47979     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     47979              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47979     47979              0         0         0         0
   in  387.99     seconds
 Image            has    47979 counts for  123.7     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     25486              0         0         0     22493
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47979     25486              0         0         0     22493
   in  387.99     seconds
 Image            has    25486 counts for  65.69     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     22696              0         0         0     25283
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47979     22696              0         0         0     25283
   in  387.99     seconds
 Image            has    22696 counts for  58.50     counts/sec
 Command not found; type ? for a command listing
!ad10010060g300370h:ASCA >
!ad10010060g300370h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060g300370h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300370h:ASCA > read events ad10010060g300370h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060g300370h:ASCA-GIS3-PH > set image sky
!ad10010060g300370h:ASCA-GIS3-PH > filter region corner_point.reg
!ad10010060g300370h:ASCA-GIS3-PH > extract image
!ad10010060g300370h:ASCA-GIS3-PH > save image outfile=ad10010060g300370_all.img
Wrote image to file ad10010060g300370_all.img
!ad10010060g300370h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10010060g300370h:ASCA-GIS3-PH > extract image
!ad10010060g300370h:ASCA-GIS3-PH > save image outfile=ad10010060g300370_lo.img
Wrote image to file ad10010060g300370_lo.img
!ad10010060g300370h:ASCA-GIS3-PH > clear pha_cut
!ad10010060g300370h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad10010060g300370h:ASCA-GIS3-PH > extract image
!ad10010060g300370h:ASCA-GIS3-PH > save image outfile=ad10010060g300370_hi.img
Wrote image to file ad10010060g300370_hi.img
!ad10010060g300370h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10010060s100102.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad10010060s100102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060s100102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL          ON
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:           IN          IN          IN          IN
 AREA DISC H START:            6           6           6         207
 AREA DISC H  STOP:            7           7           7         356
 AREA DISC V START:            2           2           2         211
 AREA DISC V  STOP:            3           3           3         360
  
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0620
 Mean   RA/DEC/ROLL :       83.5970      21.9858      92.0620
 Pnt    RA/DEC/ROLL :       83.5923      21.9747      92.0620
 
 Image rebin factor :             4
 Attitude Records   :          9081
 Hot Pixels         :           170
 GTI intervals      :             3
 Total GTI (secs)   :      1280.000
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        393.99       393.99
  20 Percent Complete: Total/live time:        393.99       393.99
  30 Percent Complete: Total/live time:        890.99       890.99
  40 Percent Complete: Total/live time:        890.99       890.99
  50 Percent Complete: Total/live time:       1280.00      1280.00
 100 Percent Complete: Total/live time:       1280.00      1280.00
 
 Number of attitude steps  used:            4
 Number of attitude steps avail:         2704
 Mean RA/DEC pixel offset:      -20.8982      -5.7770
 
    writing expo file: ad10010060s100102.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060s100102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060s100102h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:13:00    0.13E+04   183042 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         183042    183042              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        183042    183042              0         0         0         0
   in  1280.0     seconds
 Image            has   183042 counts for  143.0     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         183042    111608              0         0         0     71434
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        183042    111608              0         0         0     71434
   in  1280.0     seconds
 Image            has   111608 counts for  87.19     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         183042     71597              0         0         0    111445
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        183042     71597              0         0         0    111445
   in  1280.0     seconds
 Image            has    71597 counts for  55.94     counts/sec
 Command not found; type ? for a command listing
!ad10010060s100102h:ASCA >
!ad10010060s100102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060s100102h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060s100102h:ASCA > read events ad10010060s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad10010060s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad10010060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100102_all.img
Wrote image to file ad10010060s100102_all.img
!ad10010060s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad10010060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100102_lo.img
Wrote image to file ad10010060s100102_lo.img
!ad10010060s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad10010060s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad10010060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100102_hi.img
Wrote image to file ad10010060s100102_hi.img
!ad10010060s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad10010060s100202.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad10010060s100202h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad10010060s100202h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL          ON
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF         OFF         OFF          ON
 AREA DISC  IN/OUT:           IN          IN          IN          IN
 AREA DISC H START:            6           6           6         226
 AREA DISC H  STOP:            7           7           7         337
 AREA DISC V START:            2           2           2         230
 AREA DISC V  STOP:            3           3           3         341
  
    reading att  file: ./fa930407_2237.0053
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       83.5949      21.9787      92.0617
 Mean   RA/DEC/ROLL :       83.5977      21.9878      92.0617
 Pnt    RA/DEC/ROLL :       83.5901      21.9703      92.0617
 
 Image rebin factor :             4
 Attitude Records   :          9081
 Hot Pixels         :            13
 GTI intervals      :             2
 Total GTI (secs)   :       576.000
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        353.49       353.49
  20 Percent Complete: Total/live time:        353.49       353.49
  30 Percent Complete: Total/live time:        576.00       576.00
 100 Percent Complete: Total/live time:        576.00       576.00
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         1324
 Mean RA/DEC pixel offset:      -27.9682      -9.5703
 
    writing expo file: ad10010060s100202.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad10010060s100202h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad10010060s100202h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:39:26    0.58E+03   113572 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         113572    113572              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        113572    113572              0         0         0         0
   in  576.00     seconds
 Image            has   113572 counts for  197.2     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     68269              0         0         0     45303
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        113572     68269              0         0         0     45303
   in  576.00     seconds
 Image            has    68269 counts for  118.5     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     45422              0         0         0     68150
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        113572     45422              0         0         0     68150
   in  576.00     seconds
 Image            has    45422 counts for  78.86     counts/sec
 Command not found; type ? for a command listing
!ad10010060s100202h:ASCA >
!ad10010060s100202h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad10010060s100202h:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060s100202h:ASCA > read events ad10010060s100202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!ad10010060s100202h:ASCA-SIS1-BRIGHT > set image sky
!ad10010060s100202h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad10010060s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100202_all.img
Wrote image to file ad10010060s100202_all.img
!ad10010060s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad10010060s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100202_lo.img
Wrote image to file ad10010060s100202_lo.img
!ad10010060s100202h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad10010060s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad10010060s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10010060s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10010060s100202_hi.img
Wrote image to file ad10010060s100202_hi.img
!ad10010060s100202h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis images
-> Exposure for ad10010060s100102.expo is 1280.000000 seconds
-> Exposure for ad10010060s100202.expo is 576.000000 seconds
-> Summing the following images to produce ad10010060sis32002.totexpo
ad10010060s100102.expo
ad10010060s100202.expo
-> Setting EXPOSURE=1856 in ad10010060sis32002.totexpo
-> Exposure for ad10010060s100102_all.img is 1.280000000000000E+03 seconds
-> ad10010060s100102_all.img has 183042 counts
-> Exposure for ad10010060s100202_all.img is 5.760000000000000E+02 seconds
-> ad10010060s100202_all.img has 113572 counts
-> Summing the following images to produce ad10010060sis32002_all.totsky
ad10010060s100102_all.img
ad10010060s100202_all.img
-> Setting EXPOSURE=1856 in ad10010060sis32002_all.totsky
-> Setting TOTCTS=296614 in ad10010060sis32002_all.totsky
-> Exposure for ad10010060s100102_lo.img is 1.280000000000000E+03 seconds
-> ad10010060s100102_lo.img has 111608 counts
-> Exposure for ad10010060s100202_lo.img is 5.760000000000000E+02 seconds
-> ad10010060s100202_lo.img has 68269 counts
-> Summing the following images to produce ad10010060sis32002_lo.totsky
ad10010060s100102_lo.img
ad10010060s100202_lo.img
-> Setting EXPOSURE=1856 in ad10010060sis32002_lo.totsky
-> Setting TOTCTS=179877 in ad10010060sis32002_lo.totsky
-> Exposure for ad10010060s100102_hi.img is 1.280000000000000E+03 seconds
-> ad10010060s100102_hi.img has 71597 counts
-> Exposure for ad10010060s100202_hi.img is 5.760000000000000E+02 seconds
-> ad10010060s100202_hi.img has 45422 counts
-> Summing the following images to produce ad10010060sis32002_hi.totsky
ad10010060s100102_hi.img
ad10010060s100202_hi.img
-> Setting EXPOSURE=1856 in ad10010060sis32002_hi.totsky
-> Setting TOTCTS=117019 in ad10010060sis32002_hi.totsky
-> Running XIMAGE to create ad10010060sis32002.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   21
![1]XIMAGE> read/fits ad10010060sis32002_all.totsky
 Telescope ASCA SIS0,SIS1
 Image size = 320 x 320 pixels
 Image rebin = 4
 Image center = 640.5, 640.5
 Reading an image
  Image level, min = 0.0000000 max = 131.00000
 Saving current map
![2]XIMAGE> read/expo ad10010060sis32002.totexpo
 Telescope ASCA SIS0,SIS1
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 30.933332
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.15912
  Scaling factor :     1.00000
  Min and max :   0  110
 Max-preserving scaling factor :     1.1909091
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     1.09554E+06
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit
-> Summing gis images
-> Exposure for ad10010060g200170.expo is 797.997498 seconds
-> Exposure for ad10010060g200270.expo is 360.007263 seconds
-> Exposure for ad10010060g200370.expo is 385.988464 seconds
-> Exposure for ad10010060g300170.expo is 795.997498 seconds
-> Exposure for ad10010060g300270.expo is 358.007263 seconds
-> Exposure for ad10010060g300370.expo is 387.988464 seconds
-> Summing the following images to produce ad10010060gis25670.totexpo
ad10010060g200170.expo
ad10010060g200270.expo
ad10010060g200370.expo
ad10010060g300170.expo
ad10010060g300270.expo
ad10010060g300370.expo
-> Setting EXPOSURE=3085.98645 in ad10010060gis25670.totexpo
-> Exposure for ad10010060g200170_all.img is 7.979974903995171E+02 seconds
-> ad10010060g200170_all.img has 98418 counts
-> Exposure for ad10010060g200270_all.img is 3.600072629414499E+02 seconds
-> ad10010060g200270_all.img has 44469 counts
-> Exposure for ad10010060g200370_all.img is 3.859884585859254E+02 seconds
-> ad10010060g200370_all.img has 47547 counts
-> Exposure for ad10010060g300170_all.img is 7.959974967464805E+02 seconds
-> ad10010060g300170_all.img has 98223 counts
-> Exposure for ad10010060g300270_all.img is 3.580072695137933E+02 seconds
-> ad10010060g300270_all.img has 44363 counts
-> Exposure for ad10010060g300370_all.img is 3.879884522389621E+02 seconds
-> ad10010060g300370_all.img has 47979 counts
-> Summing the following images to produce ad10010060gis25670_all.totsky
ad10010060g200170_all.img
ad10010060g200270_all.img
ad10010060g200370_all.img
ad10010060g300170_all.img
ad10010060g300270_all.img
ad10010060g300370_all.img
-> Setting EXPOSURE=3085.98643042613 in ad10010060gis25670_all.totsky
-> Setting TOTCTS=380999 in ad10010060gis25670_all.totsky
-> Exposure for ad10010060g200170_lo.img is 7.979974903995171E+02 seconds
-> ad10010060g200170_lo.img has 51613 counts
-> Exposure for ad10010060g200270_lo.img is 3.600072629414499E+02 seconds
-> ad10010060g200270_lo.img has 23434 counts
-> Exposure for ad10010060g200370_lo.img is 3.859884585859254E+02 seconds
-> ad10010060g200370_lo.img has 25082 counts
-> Exposure for ad10010060g300170_lo.img is 7.959974967464805E+02 seconds
-> ad10010060g300170_lo.img has 51910 counts
-> Exposure for ad10010060g300270_lo.img is 3.580072695137933E+02 seconds
-> ad10010060g300270_lo.img has 23284 counts
-> Exposure for ad10010060g300370_lo.img is 3.879884522389621E+02 seconds
-> ad10010060g300370_lo.img has 25486 counts
-> Summing the following images to produce ad10010060gis25670_lo.totsky
ad10010060g200170_lo.img
ad10010060g200270_lo.img
ad10010060g200370_lo.img
ad10010060g300170_lo.img
ad10010060g300270_lo.img
ad10010060g300370_lo.img
-> Setting EXPOSURE=3085.98643042613 in ad10010060gis25670_lo.totsky
-> Setting TOTCTS=200809 in ad10010060gis25670_lo.totsky
-> Exposure for ad10010060g200170_hi.img is 7.979974903995171E+02 seconds
-> ad10010060g200170_hi.img has 47225 counts
-> Exposure for ad10010060g200270_hi.img is 3.600072629414499E+02 seconds
-> ad10010060g200270_hi.img has 21228 counts
-> Exposure for ad10010060g200370_hi.img is 3.859884585859254E+02 seconds
-> ad10010060g200370_hi.img has 22712 counts
-> Exposure for ad10010060g300170_hi.img is 7.959974967464805E+02 seconds
-> ad10010060g300170_hi.img has 46788 counts
-> Exposure for ad10010060g300270_hi.img is 3.580072695137933E+02 seconds
-> ad10010060g300270_hi.img has 21293 counts
-> Exposure for ad10010060g300370_hi.img is 3.879884522389621E+02 seconds
-> ad10010060g300370_hi.img has 22696 counts
-> Summing the following images to produce ad10010060gis25670_hi.totsky
ad10010060g200170_hi.img
ad10010060g200270_hi.img
ad10010060g200370_hi.img
ad10010060g300170_hi.img
ad10010060g300270_hi.img
ad10010060g300370_hi.img
-> Setting EXPOSURE=3085.98643042613 in ad10010060gis25670_hi.totsky
-> Setting TOTCTS=181942 in ad10010060gis25670_hi.totsky
-> Running XIMAGE to create ad10010060gis25670.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   21
![1]XIMAGE> read/fits ad10010060gis25670_all.totsky
 Telescope ASCA GIS2,GIS3
 Image size = 256 x 256 pixels
 Image rebin = 1
 Image center = 128.5, 128.5
 Reading an image
  Image level, min = 0.0000000 max = 1448.0000
 Saving current map
![2]XIMAGE> read/expo ad10010060gis25670.totexpo
 Telescope ASCA GIS2,GIS3
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 51.433113
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.36837
  Scaling factor :     1.00000
  Min and max :   0  1245
 Max-preserving scaling factor :     1.1630522
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     1.50452E+08
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit

Detecting sources in summed images (16:16:8)

-> Detecting sources in all images
-> Smoothing ad10010060gis25670_all.totsky with ad10010060gis25670.totexpo
-> Detecting sources in ad10010060gis25670_all.smooth
-> stdout output from ascasource
119 141 0.38511 100 11 3327.81
-> Smoothing ad10010060gis25670_hi.totsky with ad10010060gis25670.totexpo
-> Detecting sources in ad10010060gis25670_hi.smooth
-> stdout output from ascasource
119 141 0.210089 100 10 2683.7
-> Smoothing ad10010060gis25670_lo.totsky with ad10010060gis25670.totexpo
-> Detecting sources in ad10010060gis25670_lo.smooth
-> stdout output from ascasource
119 142 0.178729 101 11 3500.53
-> Determining extraction radii
-> Eliminating redundant sources
-> stdout output from sift_sources
119 141 24 T
-> stdout output from pix2sky
83.6368 22.0299
-> The following sources have radius > 2
10010060 1 119 141 24 83.6368 22.0299 0.098232 48.7087 44.531 T
-> Making image ad10010060gis25670_source.ps showing sources
-> stdout output from colorpic
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating source catalog ad10010060gis25670.src
-> Smoothing ad10010060sis32002_all.totsky with ad10010060sis32002.totexpo
-> Detecting sources in ad10010060sis32002_all.smooth
-> stdout output from ascasource
140 199 0.165475 11 12 615.583
137 179 0.15042 8 9 559.578
-> Smoothing ad10010060sis32002_hi.totsky with ad10010060sis32002.totexpo
-> Detecting sources in ad10010060sis32002_hi.smooth
-> stdout output from ascasource
140 199 0.0771228 197 18 536.888
-> Smoothing ad10010060sis32002_lo.totsky with ad10010060sis32002.totexpo
-> Detecting sources in ad10010060sis32002_lo.smooth
-> stdout output from ascasource
140 200 0.0902591 13 14 618.108
139 177 0.0812827 9 10 559.934
-> Determining extraction radii
-> Eliminating redundant sources
-> stdout output from sift_sources
140 199 11 T
137 179 8 F
-> stdout output from pix2sky
83.6333 22.0475
-> stdout output from pix2sky
83.639 22.0121
-> The following sources have radius > 2
10010060 1 140 199 11 83.6333 22.0475 0.019448 10.2817 8.41135 T
10010060 2 137 179 8 83.639 22.0121 0.014144 4.49131 4.88894 F
-> Making image ad10010060sis32002_source.ps showing sources
-> stdout output from colorpic
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating source catalog ad10010060sis32002.src
-> Generating region files for all sources
-> working on ad10010060sis32002.src s0 source 1
-> Converting SKY (140,199) to DET coordinates for inst=s0 dimen=320, and mode=02
-> need to merge event files
-> Merging
-> No event s0 event files with mode=02 and dimen=320
-> working on ad10010060sis32002.src s0 source 2
-> Converting SKY (137,179) to DET coordinates for inst=s0 dimen=320, and mode=02
-> need to merge event files
-> Merging
-> No event s0 event files with mode=02 and dimen=320
-> working on ad10010060sis32002.src s1 source 1
-> Converting SKY (140,199) to DET coordinates for inst=s1 dimen=320, and mode=02
-> need to merge event files
-> Merging ad10010060s100102h.evt ad10010060s100202h.evt
-> DETX=119, DETY=137 using 8 pixel radius (using 1084 events)
-> working on ad10010060sis32002.src s1 source 2
-> Converting SKY (137,179) to DET coordinates for inst=s1 dimen=320, and mode=02
-> DETX=139, DETY=136 using 8 pixel radius (using 330 events)
-> working on ad10010060gis25670.src g2 source 1
-> Converting SKY (119,141) to DET coordinates for inst=g2 dimen=256, and mode=70
-> need to merge event files
-> Merging ad10010060g200170h.evt ad10010060g200270h.evt ad10010060g200370h.evt
-> DETX=113, DETY=118 using 2 pixel radius (using 8767 events)
-> working on ad10010060gis25670.src g3 source 1
-> Converting SKY (119,141) to DET coordinates for inst=g3 dimen=256, and mode=70
-> need to merge event files
-> Merging ad10010060g300170h.evt ad10010060g300270h.evt ad10010060g300370h.evt
-> DETX=119, DETY=118 using 2 pixel radius (using 8236 events)

Extracting spectra and generating response matrices (16:21:10)

-> Fetching xrt_ea_v2_0.fits
-> Fetching xrt_psf_v2_0.fits
-> sisph2pi_110397.fits already present in current directory
-> Fetching sisechos_290296.fits
-> Fetching sisrddis_290296.fits
-> Standard Output From STOOL group_event_files:
1 ad10010060s100102h.evt 183042
2 ad10010060s100202h.evt 113572
-> Skipping BRIGHT mode files with SPTR = 20
ad10010060s100102h.evt
-> Skipping BRIGHT mode files with SPTR = 20
ad10010060s100202h.evt
-> Standard Output From STOOL group_event_files:
1 ad10010060g200170h.evt 190434
1 ad10010060g200270h.evt 190434
1 ad10010060g200370h.evt 190434
-> GIS2_REGION256_OFF.4 already present in current directory
-> Extracting ad10010060g210170_1.pi from ad10010060g225670_1.reg and:
ad10010060g200170h.evt
ad10010060g200270h.evt
ad10010060g200370h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03    98418     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.36E+03    44469     1024
      2 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03    98418     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.36E+03    44469     1024
      2 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47547     1024
      3 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03    98418     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     83864          14554         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     37622           6847         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     40091           7456         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        190434    161577          28857         0         0         0
   in  1544.0     seconds
 Spectrum         has   161577 counts for  104.6     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 1544.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g210170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > read events ad10010060g200270h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > read events ad10010060g200370h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad10010060g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10010060g210170_1.pi group=yes
Wrote spectrum to ad10010060g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting BLANK keyword from ad10010060g210170_1.pi
-> Correcting ad10010060g210170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad10010060g210170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 327.07          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      19  are grouped by a factor       20
 ...        20 -     533  are single channels
 ...       534 -     535  are grouped by a factor        2
 ...       536 -     536  are single channels
 ...       537 -     538  are grouped by a factor        2
 ...       539 -     545  are single channels
 ...       546 -     547  are grouped by a factor        2
 ...       548 -     550  are single channels
 ...       551 -     564  are grouped by a factor        2
 ...       565 -     568  are single channels
 ...       569 -     572  are grouped by a factor        2
 ...       573 -     573  are single channels
 ...       574 -     629  are grouped by a factor        2
 ...       630 -     632  are grouped by a factor        3
 ...       633 -     634  are grouped by a factor        2
 ...       635 -     637  are grouped by a factor        3
 ...       638 -     639  are grouped by a factor        2
 ...       640 -     642  are grouped by a factor        3
 ...       643 -     656  are grouped by a factor        2
 ...       657 -     659  are grouped by a factor        3
 ...       660 -     661  are grouped by a factor        2
 ...       662 -     665  are grouped by a factor        4
 ...       666 -     671  are grouped by a factor        3
 ...       672 -     679  are grouped by a factor        4
 ...       680 -     682  are grouped by a factor        3
 ...       683 -     686  are grouped by a factor        4
 ...       687 -     695  are grouped by a factor        3
 ...       696 -     727  are grouped by a factor        4
 ...       728 -     737  are grouped by a factor        5
 ...       738 -     740  are grouped by a factor        3
 ...       741 -     745  are grouped by a factor        5
 ...       746 -     749  are grouped by a factor        4
 ...       750 -     754  are grouped by a factor        5
 ...       755 -     760  are grouped by a factor        6
 ...       761 -     770  are grouped by a factor        5
 ...       771 -     778  are grouped by a factor        8
 ...       779 -     790  are grouped by a factor        6
 ...       791 -     795  are grouped by a factor        5
 ...       796 -     802  are grouped by a factor        7
 ...       803 -     810  are grouped by a factor        8
 ...       811 -     819  are grouped by a factor        9
 ...       820 -     827  are grouped by a factor        8
 ...       828 -     839  are grouped by a factor       12
 ...       840 -     861  are grouped by a factor       11
 ...       862 -     885  are grouped by a factor       12
 ...       886 -     900  are grouped by a factor       15
 ...       901 -     916  are grouped by a factor       16
 ...       917 -     938  are grouped by a factor       22
 ...       939 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g210170_1.pi
 ** grppha 2.9.0 completed successfully
-> Fetching gis2v4_0.rmf
-> Fetching s2bev1.fits
-> Fetching s2gridv3.fits
-> Generating ad10010060g210170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   48 by   48 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   50   55
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.61247E+05
 Weighted mean angle from optical axis  =  6.020 arcmin
-> Standard Output From STOOL group_event_files:
1 ad10010060g300170h.evt 190565
1 ad10010060g300270h.evt 190565
1 ad10010060g300370h.evt 190565
-> GIS3_REGION256_OFF.4 already present in current directory
-> Extracting ad10010060g310170_1.pi from ad10010060g325670_1.reg and:
ad10010060g300170h.evt
ad10010060g300270h.evt
ad10010060g300370h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03    98223     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.36E+03    44363     1024
      2 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03    98223     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.36E+03    44363     1024
      2 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47979     1024
      3 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03    98223     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     84540          13683         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     38293           6070         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     41268           6711         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        190565    164101          26464         0         0         0
   in  1542.0     seconds
 Spectrum         has   164101 counts for  106.4     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 1542.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g310170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > read events ad10010060g300270h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > read events ad10010060g300370h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad10010060g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10010060g310170_1.pi group=yes
Wrote spectrum to ad10010060g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting BLANK keyword from ad10010060g310170_1.pi
-> Correcting ad10010060g310170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad10010060g310170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 297.43          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      19  are grouped by a factor       20
 ...        20 -      21  are grouped by a factor        2
 ...        22 -     516  are single channels
 ...       517 -     518  are grouped by a factor        2
 ...       519 -     548  are single channels
 ...       549 -     552  are grouped by a factor        2
 ...       553 -     553  are single channels
 ...       554 -     559  are grouped by a factor        2
 ...       560 -     561  are single channels
 ...       562 -     575  are grouped by a factor        2
 ...       576 -     576  are single channels
 ...       577 -     578  are grouped by a factor        2
 ...       579 -     579  are single channels
 ...       580 -     645  are grouped by a factor        2
 ...       646 -     648  are grouped by a factor        3
 ...       649 -     660  are grouped by a factor        2
 ...       661 -     669  are grouped by a factor        3
 ...       670 -     671  are grouped by a factor        2
 ...       672 -     674  are grouped by a factor        3
 ...       675 -     676  are grouped by a factor        2
 ...       677 -     679  are grouped by a factor        3
 ...       680 -     681  are grouped by a factor        2
 ...       682 -     684  are grouped by a factor        3
 ...       685 -     688  are grouped by a factor        4
 ...       689 -     703  are grouped by a factor        3
 ...       704 -     707  are grouped by a factor        4
 ...       708 -     716  are grouped by a factor        3
 ...       717 -     728  are grouped by a factor        4
 ...       729 -     733  are grouped by a factor        5
 ...       734 -     737  are grouped by a factor        4
 ...       738 -     740  are grouped by a factor        3
 ...       741 -     756  are grouped by a factor        4
 ...       757 -     766  are grouped by a factor        5
 ...       767 -     770  are grouped by a factor        4
 ...       771 -     780  are grouped by a factor        5
 ...       781 -     786  are grouped by a factor        6
 ...       787 -     793  are grouped by a factor        7
 ...       794 -     799  are grouped by a factor        6
 ...       800 -     813  are grouped by a factor        7
 ...       814 -     821  are grouped by a factor        8
 ...       822 -     835  are grouped by a factor        7
 ...       836 -     844  are grouped by a factor        9
 ...       845 -     864  are grouped by a factor       10
 ...       865 -     877  are grouped by a factor       13
 ...       878 -     887  are grouped by a factor       10
 ...       888 -     899  are grouped by a factor       12
 ...       900 -     914  are grouped by a factor       15
 ...       915 -     933  are grouped by a factor       19
 ...       934 -     963  are grouped by a factor       30
 ...       964 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g310170_1.pi
 ** grppha 2.9.0 completed successfully
-> Fetching gis3v4_0.rmf
-> Fetching s3bev1.fits
-> Fetching s3gridv3.fits
-> Generating ad10010060g310170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   48 by   48 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   56   55
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.63842E+05
 Weighted mean angle from optical axis  =  4.525 arcmin
-> Plotting ad10010060g210170_1_pi.ps from ad10010060g210170_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 16:26:39 23-Aug-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad10010060g210170_1.pi;
 Net count rate (cts/s) for file   1   494.0    +/-   1.229
   using response (RMF) file...       gis2v4_0.rmf
   using auxiliary (ARF) file...      ad10010060g210170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad10010060g310170_1_pi.ps from ad10010060g310170_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 16:26:59 23-Aug-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad10010060g310170_1.pi;
 Net count rate (cts/s) for file   1   551.7    +/-   1.362
   using response (RMF) file...       gis3v4_0.rmf
   using auxiliary (ARF) file...      ad10010060g310170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

Extracting light curves (16:27:5)

-> No files for s0 mode 02
-> Working on s0 mode 03
-> Extracting lightcurves from ad10010060s000103h.evt ad10010060s000203m.evt
-> Largest TIMEDEL=4.0000000E+00
-> Extracting ad10010060s000003_0.lc from full field of view
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: ad10010060s000103h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          14320     14320              0         0         0         0
 Doing file: ad10010060s000203m.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
           1601      1601              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15921     15921              0         0         0         0
   in  2172.0     seconds
 Fits light curve has    15921 counts for  7.330     counts/sec
-> Working on s1 mode 02
-> Extracting lightcurves from ad10010060s100102h.evt ad10010060s100202h.evt
-> Largest TIMEDEL=1.6000000E+01
-> Extracting event file filtered with ad10010060s132002_1.reg
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: ad10010060s100102h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         183042      1509         181533         0         0         0
 Writing events file
   1509 events written to the output file
 Doing file: ad10010060s100202h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     21762          91810         0         0         0
 Writing events file
  23271 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        296614     23271         273343         0         0         0
   in  1856.0     seconds
-> Extracting ad10010060s132002_1.lc with binsize 1.6000000E+01
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: lightcurve_filtered_events.tmp
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          23271     23271              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         23271     23271              0         0         0         0
   in  1856.0     seconds
 Fits light curve has    23271 counts for  12.54     counts/sec
-> Extracting event file filtered with ad10010060s132002_2.reg
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: ad10010060s100102h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         183042      1233         181809         0         0         0
 Writing events file
   1233 events written to the output file
 Doing file: ad10010060s100202h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     10410         103162         0         0         0
 Writing events file
  11643 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        296614     11643         284971         0         0         0
   in  1856.0     seconds
-> Extracting ad10010060s132002_2.lc with binsize 1.6000000E+01
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: lightcurve_filtered_events.tmp
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          11643     11643              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11643     11643              0         0         0         0
   in  1856.0     seconds
 Fits light curve has    11643 counts for  6.273     counts/sec
-> No files for s1 mode 03
-> Working on g2 mode 70
-> Extracting lightcurves from ad10010060g200170h.evt ad10010060g200270h.evt ad10010060g200370h.evt
-> Largest TIMEDEL=6.2500000E-02
-> Extracting event file filtered with ad10010060g225670_1.reg
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: ad10010060g200170h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     83864          14554         0         0         0
 Writing events file
  83864 events written to the output file
 Doing file: ad10010060g200270h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     37622           6847         0         0         0
 Writing events file
 121486 events written to the output file
 Doing file: ad10010060g200370h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     40091           7456         0         0         0
 Writing events file
 161577 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        190434    161577          28857         0         0         0
   in  1544.0     seconds
-> Extracting ad10010060g225670_1.lc with binsize 0.477788672143909
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: lightcurve_filtered_events.tmp
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         161577    161577              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        161577    161577              0         0         0         0
   in  1544.0     seconds
 Fits light curve has   161577 counts for  104.6     counts/sec
-> No files for g2 mode 71
-> Working on g3 mode 70
-> Extracting lightcurves from ad10010060g300170h.evt ad10010060g300270h.evt ad10010060g300370h.evt
-> Largest TIMEDEL=6.2500000E-02
-> Extracting event file filtered with ad10010060g325670_1.reg
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: ad10010060g300170h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     84540          13683         0         0         0
 Writing events file
  84540 events written to the output file
 Doing file: ad10010060g300270h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     38293           6070         0         0         0
 Writing events file
 122833 events written to the output file
 Doing file: ad10010060g300370h.evt
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     41268           6711         0         0         0
 Writing events file
 164101 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        190565    164101          26464         0         0         0
   in  1542.0     seconds
-> Extracting ad10010060g325670_1.lc with binsize 0.469830534899931
-> stdout output from extractor
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: lightcurve_filtered_events.tmp
 10% completed
 20% completed
 30% completed
 40% completed
 50% completed
 60% completed
 70% completed
 80% completed
 90% completed
100% completed
          Total      Good    Bad: Region      Time     Phase       Cut
         164101    164101              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        164101    164101              0         0         0         0
   in  1542.0     seconds
 Fits light curve has   164101 counts for  106.4     counts/sec
-> No files for g3 mode 71
-> Plotting all lightcurves
-> Plotting ad10010060g225670_1.lc in ad10010060g225670_1_lc.ps
-> stdout output from lcurve
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad10010060g225670_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ CRAB                Start Time (d) ....  9084 23:14:30.605
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9084 23:49:50.599
 No. of Rows .......         3231        Bin Time (s) ......   0.4778
 Right Ascension ... 8.3595E+01          Internal time sys.. Converted to TJD
 Declination ....... 2.1979E+01          Experiment ........ ASCA     GIS2
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ...  9084.96840978437  (days)      23:14:30:605  (h:m:s:ms)
 Expected Stop ....  9084.99294674276  (days)      23:49:50:599  (h:m:s:ms)
 
 Minimum Newbin Time   0.47778867      (s)
 for Maximum Newbin No..             4438
 
 Default Newbin Time is:   4.1454697    (s) (to have 1 Intv. of     512 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     4.1454697      (s)
 Maximum Newbin No.               512
 
 Default Newbins per Interval are:       512
 (giving       1 Interval of       512 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       512 Newbins of       4.14547     (s)
 
     512 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start  9084 23:14:32
     Ser.1     Avg  104.6        Chisq  69.92       Var  4.851     Newbs.    374
               Min  98.14          Max  111.2    expVar  25.68      Bins   3231
PLT> @lightcurve_plot_commands.tmp
!PLT> dev ad10010060g225670_1_lc.ps/ps
!PLT> LA File ad10010060g225670_1.lc
!PLT> plot
!PLT> quit
-> Plotting ad10010060g325670_1.lc in ad10010060g325670_1_lc.ps
-> stdout output from lcurve
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad10010060g325670_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ CRAB                Start Time (d) ....  9084 23:14:32.605
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9084 23:49:50.599
 No. of Rows .......         3282        Bin Time (s) ......   0.4698
 Right Ascension ... 8.3595E+01          Internal time sys.. Converted to TJD
 Declination ....... 2.1979E+01          Experiment ........ ASCA     GIS3
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ...  9084.96843293244  (days)      23:14:32:605  (h:m:s:ms)
 Expected Stop ....  9084.99294674276  (days)      23:49:50:599  (h:m:s:ms)
 
 Minimum Newbin Time   0.46983053      (s)
 for Maximum Newbin No..             4508
 
 Default Newbin Time is:   4.1415589    (s) (to have 1 Intv. of     512 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     4.1415589      (s)
 Maximum Newbin No.               512
 
 Default Newbins per Interval are:       512
 (giving       1 Interval of       512 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       512 Newbins of       4.14156     (s)
 
     512 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start  9084 23:14:34
     Ser.1     Avg  106.4        Chisq  69.85       Var  4.867     Newbs.    374
               Min  99.09          Max  113.3    expVar  26.01      Bins   3282
PLT> @lightcurve_plot_commands.tmp
!PLT> dev ad10010060g325670_1_lc.ps/ps
!PLT> LA File ad10010060g325670_1.lc
!PLT> plot
!PLT> quit
-> Plotting ad10010060s000003_0.lc in ad10010060s000003_0_lc.ps
-> stdout output from lcurve
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad10010060s000003_0.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ CRAB                Start Time (d) ....  9084 23:16:14.613
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9084 23:53:34.613
 No. of Rows .......          318        Bin Time (s) ......    6.821
 Right Ascension ... 8.3595E+01          Internal time sys.. Converted to TJD
 Declination ....... 2.1979E+01          Experiment ........ ASCA     SIS0
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ...  9084.96961357213  (days)      23:16:14:613  (h:m:s:ms)
 Expected Stop ....  9084.99553949806  (days)      23:53:34:613  (h:m:s:ms)
 
 Minimum Newbin Time    6.8211802      (s)
 for Maximum Newbin No..              329
 
 Default Newbin Time is:   6.8211802    (s) (to have 1 Intv. of     329 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     6.8211802      (s)
 Maximum Newbin No.               329
 
 Default Newbins per Interval are:       329
 (giving       1 Interval of       329 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       329 Newbins of       6.82118     (s)
 
     329 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start  9084 23:16:18
     Ser.1     Avg  7.323        Chisq  3880.       Var  13.14     Newbs.    318
               Min 0.1466          Max  13.63    expVar  1.076      Bins    318
PLT> @lightcurve_plot_commands.tmp
!PLT> dev ad10010060s000003_0_lc.ps/ps
!PLT> LA File ad10010060s000003_0.lc
!PLT> plot
!PLT> quit
-> Plotting ad10010060s132002_1.lc in ad10010060s132002_1_lc.ps
-> stdout output from lcurve
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad10010060s132002_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ CRAB                Start Time (d) ....  9084 23:16:14.613
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9084 23:50:22.613
 No. of Rows .......          116        Bin Time (s) ......    16.00
 Right Ascension ... 8.3595E+01          Internal time sys.. Converted to TJD
 Declination ....... 2.1979E+01          Experiment ........ ASCA     SIS1
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ...  9084.96961357213  (days)      23:16:14:613  (h:m:s:ms)
 Expected Stop ....  9084.99331727584  (days)      23:50:22:613  (h:m:s:ms)
 
 Minimum Newbin Time    16.000000      (s)
 for Maximum Newbin No..              129
 
 Default Newbin Time is:   16.000000    (s) (to have 1 Intv. of     129 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     16.000000      (s)
 Maximum Newbin No.               129
 
 Default Newbins per Interval are:       129
 (giving       1 Interval of       129 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       129 Newbins of       16.0000     (s)
 
     129 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start  9084 23:16:22
     Ser.1     Avg  12.54        Chisq 0.4255E+05   Var  287.4     Newbs.    116
               Min 0.6875          Max  40.88    expVar 0.7836      Bins    116
PLT> @lightcurve_plot_commands.tmp
!PLT> dev ad10010060s132002_1_lc.ps/ps
!PLT> LA File ad10010060s132002_1.lc
!PLT> plot
!PLT> quit
-> Plotting ad10010060s132002_2.lc in ad10010060s132002_2_lc.ps
-> stdout output from lcurve
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad10010060s132002_2.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ CRAB                Start Time (d) ....  9084 23:16:14.613
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9084 23:50:22.613
 No. of Rows .......          116        Bin Time (s) ......    16.00
 Right Ascension ... 8.3595E+01          Internal time sys.. Converted to TJD
 Declination ....... 2.1979E+01          Experiment ........ ASCA     SIS1
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ...  9084.96961357213  (days)      23:16:14:613  (h:m:s:ms)
 Expected Stop ....  9084.99331727584  (days)      23:50:22:613  (h:m:s:ms)
 
 Minimum Newbin Time    16.000000      (s)
 for Maximum Newbin No..              129
 
 Default Newbin Time is:   16.000000    (s) (to have 1 Intv. of     129 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     16.000000      (s)
 Maximum Newbin No.               129
 
 Default Newbins per Interval are:       129
 (giving       1 Interval of       129 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       129 Newbins of       16.0000     (s)
 
     129 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start  9084 23:16:22
     Ser.1     Avg  6.273        Chisq 0.1867E+05   Var  63.10     Newbs.    116
               Min 0.1875          Max  19.75    expVar 0.3921      Bins    116
PLT> @lightcurve_plot_commands.tmp
!PLT> dev ad10010060s132002_2_lc.ps/ps
!PLT> LA File ad10010060s132002_2.lc
!PLT> plot
!PLT> quit
-> Creating GIS monitor count (HK) lightcurves
-> Creating a merged GTI file for g2
-> Making L1 light curve of ft930407_2237_0053G2HK.fits with irate=HIGH
-> stdout output from ghkcurve
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  12350 output records from   12352  good input G2_L1    records.
-> Making L1 light curve of ft930407_2237_0053G2HK.fits with irate=HI+MED
-> stdout output from ghkcurve
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   1542 output records from   12352  good input G2_L1    records.
-> Creating a merged GTI file for g3
-> Making L1 light curve of ft930407_2237_0053G3HK.fits with irate=HIGH
-> stdout output from ghkcurve
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  12334 output records from   12336  good input G3_L1    records.
-> Making L1 light curve of ft930407_2237_0053G3HK.fits with irate=HI+MED
-> stdout output from ghkcurve
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   1540 output records from   12336  good input G3_L1    records.

Extracting source event files (16:31:6)

-> Extracting unbinned light curve ad10010060g200170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03    98418     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98418     83864          14554         0         0         0
 Writing events file
  83864 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98418     83864          14554         0         0         0
   in  798.00     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad10010060g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10010060g200170.ulc use_events=yes
Wrote events list to file ad10010060g200170.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060g200270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.36E+03    44469     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44469     37622           6847         0         0         0
 Writing events file
  37622 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44469     37622           6847         0         0         0
   in  360.01     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g200270h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad10010060g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10010060g200270.ulc use_events=yes
Wrote events list to file ad10010060g200270.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060g200370.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47547     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47547     40091           7456         0         0         0
 Writing events file
  40091 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47547     40091           7456         0         0         0
   in  385.99     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g200370h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad10010060g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10010060g200370.ulc use_events=yes
Wrote events list to file ad10010060g200370.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060g300170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03    98223     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          98223     84540          13683         0         0         0
 Writing events file
  84540 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98223     84540          13683         0         0         0
   in  796.00     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad10010060g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10010060g300170.ulc use_events=yes
Wrote events list to file ad10010060g300170.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060g300270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.36E+03    44363     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          44363     38293           6070         0         0         0
 Writing events file
  38293 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         44363     38293           6070         0         0         0
   in  358.01     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g300270h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad10010060g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10010060g300270.ulc use_events=yes
Wrote events list to file ad10010060g300270.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060g300370.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.39E+03    47979     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          47979     41268           6711         0         0         0
 Writing events file
  41268 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         47979     41268           6711         0         0         0
   in  387.99     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g300370h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad10010060g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10010060g300370.ulc use_events=yes
Wrote events list to file ad10010060g300370.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10010060s000103.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        FAST        HIGH        1993-04-07  23:14:46    0.20E+04    14320 1000
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000103h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          14320     14320              0         0         0         0
 Writing events file
  14320 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         14320     14320              0         0         0         0
   in  1983.9     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s000103h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
Setting X and Y to RAW
 
Getting Min and Max for Energy Column...
Got min and max for PHA:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
Area discrimination is enabled.
The mask is set from    6 to    7
Only photons inside the mask are in the telemetry.
SELECT FAST is unnecessary in this case.
!xsel:ASCA-SIS0-FAST > set image det
!xsel:ASCA-SIS0-FAST > filter region ad10010060s032002_0.reg
Region filters would not be valid for this data.
!xsel:ASCA-SIS0-FAST > extract events
!xsel:ASCA-SIS0-FAST > save events outfile=ad10010060s000103.ulc use_events=yes
Wrote events list to file ad10010060s000103.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS0-FAST > exit save_session=no
-> Extracting unbinned light curve ad10010060s000203.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        FAST        MEDIUM      1993-04-07  23:50:26    0.19E+03     1601 1000
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000203m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1601      1601              0         0         0         0
 Writing events file
   1601 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1601      1601              0         0         0         0
   in  188.14     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s000203m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
Setting X and Y to RAW
 
Getting Min and Max for Energy Column...
Got min and max for PHA:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
Area discrimination is enabled.
The mask is set from    6 to    7
Only photons inside the mask are in the telemetry.
SELECT FAST is unnecessary in this case.
!xsel:ASCA-SIS0-FAST > set image det
!xsel:ASCA-SIS0-FAST > filter region ad10010060s032002_0.reg
Region filters would not be valid for this data.
!xsel:ASCA-SIS0-FAST > extract events
!xsel:ASCA-SIS0-FAST > save events outfile=ad10010060s000203.ulc use_events=yes
Wrote events list to file ad10010060s000203.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS0-FAST > exit save_session=no
-> Extracting unbinned light curve ad10010060s100102.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:13:00    0.13E+04   183042 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         183042      1509         181533         0         0         0
 Writing events file
   1509 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        183042      1509         181533         0         0         0
   in  1280.0     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad10010060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10010060s100102.ulc use_events=yes
Wrote events list to file ad10010060s100102.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10010060s100102.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:13:00    0.13E+04   183042 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         183042      1233         181809         0         0         0
 Writing events file
   1233 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        183042      1233         181809         0         0         0
   in  1280.0     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad10010060s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10010060s100102.ulc use_events=yes
Wrote events list to file ad10010060s100102.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10010060s100202.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:39:26    0.58E+03   113572 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     21762          91810         0         0         0
 Writing events file
  21762 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        113572     21762          91810         0         0         0
   in  576.00     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s100202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad10010060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10010060s100202.ulc use_events=yes
Wrote events list to file ad10010060s100202.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10010060s100202.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:39:26    0.58E+03   113572 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
         113572     10410         103162         0         0         0
 Writing events file
  10410 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        113572     10410         103162         0         0         0
   in  576.00     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060s100202h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad10010060s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10010060s100202.ulc use_events=yes
Wrote events list to file ad10010060s100202.ulc
Changing Data directory from:
    /data/data24/seq_proc/ad0_10010060.015/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no

Extracting FRAME mode data (16:38:6)

-> Extracting FRAME mode data from ft930407_2237.0053
-> stdout output from tlmFrm
 *** tlmFrm Version 1.1 (1997-08-25) *** 
total number of superframes: 2275

Total of 0 sets of frame data are extracted.
-> Extracting corner pixel histograms
-> Extracting corner pixels from ad10010060s000301h.unf
-> Calculating corner pixel GTI from ft930407_2237_0053.mkf
-> Extracting corner pixels from ad10010060s000601m.unf
-> Extracting corner pixels from ad10010060s100501h.unf
-> Extracting corner pixels from ad10010060s100701m.unf

Extracting GIS calibration source spectra (16:38:40)

-> Standard Output From STOOL group_event_files:
1 ad10010060g200170h.unf 273921
1 ad10010060g200270h.unf 273921
1 ad10010060g200370h.unf 273921
-> Group with the most counts: 1
-> Fetching GIS2_CALSRC256.2
-> Extracting ad10010060g220170.cal from ad10010060g200170h.unf ad10010060g200270h.unf ad10010060g200370h.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.17E+04    98048     1024
      2 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.17E+04    98048     1024
      2 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73729     1024
      3 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102144       161         101983         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          98048       653          97395         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          73729       110          73619         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        273921       924         272997         0         0         0
   in  3072.0     seconds
 Spectrum         has      924 counts for 0.3008     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 3072.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.57970E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g220170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > read events ad10010060g200270h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > read events ad10010060g200370h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10010060g220170.cal group=yes
Wrote spectrum to ad10010060g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting BLANK keyword from ad10010060g220170.cal
-> gis2v4_0.rmf already present in current directory
-> Plotting ad10010060g220170_cal.ps and finding peak
-> Standard Output From STOOL xspec:

               Xspec 11.00 16:40:04 23-Aug-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad10010060g220170.cal;
 Net count rate (cts/s) for file   1  0.3008    +/-  1.0320E-02
   using response (RMF) file...       gis2v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      1111433.     using    84 PHA bins.
 Reduced chi-squared =      14624.12     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =      1111433.     using    84 PHA bins.
 Reduced chi-squared =      14434.19     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =      1111433.     using    84 PHA bins.
 Reduced chi-squared =      14249.14     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      353.5074     using    84 PHA bins.
 Reduced chi-squared =      4.474777     for     79 degrees of freedom
 Null hypothesis probability = 2.258E-36

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   81.7449      0         0.      7.2159E-03   5.861          0.
              0.1180      2.6760E-02
   81.6712      0         0.      7.1567E-03   5.859          0.
              0.1182      2.6760E-02
   81.6107      0         0.      7.1029E-03   5.856          0.
              0.1184      2.6762E-02
   81.6034      1         0.      7.0974E-03   5.855          0.
              0.1184      2.6760E-02
   81.5835      1         0.      7.0920E-03   5.855      4.2541E-04
              0.1184      2.6731E-02
   81.5206      1         0.      7.0866E-03   5.855      8.4959E-04
              0.1185      2.6703E-02
   81.5206      7         0.      7.0866E-03   5.855      8.4959E-04
              0.1185      2.6703E-02
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 1.62E-06 | -0.99  0.00  0.00 -0.03 -0.12
 1.33E-05 |  0.12 -0.08  0.03 -0.04 -0.99
 4.60E-05 | -0.03 -0.05  0.01  1.00 -0.03
 3.11E-04 |  0.01  0.89 -0.45  0.05 -0.09
 3.55E-02 |  0.00  0.45  0.89  0.02 -0.01
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               7.0866E-03 +/-  0.1405E-02
    3    3    2   gaussian/b LineE    keV        5.855     +/-  0.8618E-01
    4    4    2   gaussian/b Sigma    keV       8.4959E-04 +/-  0.1685
    5    5    2   gaussian/b norm               0.1185     +/-  0.7456E-02
    6    3    3   gaussian/b LineE    keV        6.446     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       8.9147E-04 = par   4 *   1.049
    8    6    3   gaussian/b norm               2.6703E-02 +/-  0.4428E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      81.52061     using    84 PHA bins.
 Reduced chi-squared =      1.031906     for     79 degrees of freedom
 Null hypothesis probability = 0.401

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS2 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Calibration source ad10010060g220170.cal peaks at 5.855 +/- 0.08618 keV
-> Standard Output From STOOL group_event_files:
1 ad10010060g300170h.unf 273430
1 ad10010060g300270h.unf 273430
1 ad10010060g300370h.unf 273430
-> Group with the most counts: 1
-> Fetching GIS3_CALSRC256.2
-> Extracting ad10010060g320170.cal from ad10010060g300170h.unf ad10010060g300270h.unf ad10010060g300370h.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.17E+04    97559     1024
      2 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.17E+04    97559     1024
      2 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73983     1024
      3 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         101888       160         101728         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          97559       575          96984         0         0         0
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          73983       107          73876         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        273430       842         272588         0         0         0
   in  3070.0     seconds
 Spectrum         has      842 counts for 0.2743     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 3070.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.83360E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad10010060g320170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA > read events ad10010060g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > read events ad10010060g300270h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > read events ad10010060g300370h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10010060g320170.cal group=yes
Wrote spectrum to ad10010060g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting BLANK keyword from ad10010060g320170.cal
-> gis3v4_0.rmf already present in current directory
-> Plotting ad10010060g320170_cal.ps and finding peak
-> Standard Output From STOOL xspec:

               Xspec 11.00 16:41:31 23-Aug-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad10010060g320170.cal;
 Net count rate (cts/s) for file   1  0.2743    +/-  9.9762E-03
   using response (RMF) file...       gis3v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      1285216.     using    84 PHA bins.
 Reduced chi-squared =      16910.73     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =      1285216.     using    84 PHA bins.
 Reduced chi-squared =      16691.11     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =      1285216.     using    84 PHA bins.
 Reduced chi-squared =      16477.12     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      344.9140     using    84 PHA bins.
 Reduced chi-squared =      4.366000     for     79 degrees of freedom
 Null hypothesis probability = 6.475E-35

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   92.6887     -4         0.      5.8369E-03   5.904          0.
              0.1135      1.7486E-02
   92.6539      0         0.      5.8435E-03   5.904          0.
              0.1133      1.7564E-02
   92.6507      1         0.      5.8441E-03   5.905          0.
              0.1133      1.7572E-02
   82.7376      0         0.      5.7678E-03   5.913      7.8789E-02
              0.1139      1.6986E-02
   73.2586     -1         0.      4.8145E-03   5.925      0.2076
              0.1265      1.3116E-02
   67.3164     -2         0.      5.0334E-03   5.939      0.1777
              0.1323      8.9799E-03
   67.2851     -3         0.      4.9481E-03   5.937      0.1753
              0.1323      9.0373E-03
   67.2849      0         0.      4.9607E-03   5.937      0.1754
              0.1323      9.0321E-03
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 1.83E-06 | -0.98  0.00 -0.02 -0.04 -0.18
 1.07E-05 |  0.18 -0.11 -0.05 -0.05 -0.98
 4.78E-05 | -0.03 -0.06 -0.14  0.99 -0.04
 2.80E-04 |  0.02  0.88 -0.47 -0.02 -0.07
 8.14E-04 | -0.01  0.46  0.87  0.14 -0.10
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               4.9607E-03 +/-  0.1521E-02
    3    3    2   gaussian/b LineE    keV        5.937     +/-  0.1971E-01
    4    4    2   gaussian/b Sigma    keV       0.1754     +/-  0.2608E-01
    5    5    2   gaussian/b norm               0.1323     +/-  0.7966E-02
    6    3    3   gaussian/b LineE    keV        6.537     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       0.1841     = par   4 *   1.049
    8    6    3   gaussian/b norm               9.0321E-03 +/-  0.4460E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      67.28493     using    84 PHA bins.
 Reduced chi-squared =     0.8517081     for     79 degrees of freedom
 Null hypothesis probability = 0.823

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS3 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Calibration source ad10010060g320170.cal peaks at 5.937 +/- 0.01971 keV

Extracting bright and dark Earth event files. (16:41:42)

-> Extracting bright and dark Earth events from ad10010060s000302h.unf
-> Extracting ad10010060s000302h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-08  00:26:40    0.47E+03     3433 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000302h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3433      3433              0         0         0         0
 Writing events file
   3433 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3433      3433              0         0         0         0
   in  468.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s000302h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10010060s000302h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s000302h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3433
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              67        1837
 Flickering pixels iter, pixels & cnts :   1          15         105
cleaning chip # 1
 Hot pixels & counts                   :              19         398
 Flickering pixels iter, pixels & cnts :   1           3          13
cleaning chip # 2
 Hot pixels & counts                   :              16         235
 Flickering pixels iter, pixels & cnts :   1          28         120
cleaning chip # 3
 Hot pixels & counts                   :              18         356
 Flickering pixels iter, pixels & cnts :   1          13          54
 
 Number of pixels rejected           :          179
 Number of (internal) image counts   :         3433
 Number of image cts rejected (N, %) :         311890.82
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            82           22           44           31
 
 Image counts      :          1991          455          494          493
 Image cts rejected:          1942          411          355          410
 Image cts rej (%) :         97.54        90.33        71.86        83.16
 
    filtering data...
 
 Total counts      :          1991          455          494          493
 Total cts rejected:          1942          411          355          410
 Total cts rej (%) :         97.54        90.33        71.86        83.16
 
 Number of clean counts accepted  :          315
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          179
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s000312h.unf
-> Extracting ad10010060s000312h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT2     HIGH        1993-04-08  00:26:40    0.47E+03     3630 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000312h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3630      3630              0         0         0         0
 Writing events file
   3630 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3630      3630              0         0         0         0
   in  468.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s000312h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad10010060s000312h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s000312h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3630
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              68        1872
 Flickering pixels iter, pixels & cnts :   1          15         105
cleaning chip # 1
 Hot pixels & counts                   :              19         398
 Flickering pixels iter, pixels & cnts :   1           3          13
cleaning chip # 2
 Hot pixels & counts                   :              17         251
 Flickering pixels iter, pixels & cnts :   1          34         143
cleaning chip # 3
 Hot pixels & counts                   :              18         360
 Flickering pixels iter, pixels & cnts :   1          14          57
 
 Number of pixels rejected           :          188
 Number of (internal) image counts   :         3630
 Number of image cts rejected (N, %) :         319988.13
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            83           22           51           32
 
 Image counts      :          2051          478          582          519
 Image cts rejected:          1977          411          394          417
 Image cts rej (%) :         96.39        85.98        67.70        80.35
 
    filtering data...
 
 Total counts      :          2051          478          582          519
 Total cts rejected:          1977          411          394          417
 Total cts rej (%) :         96.39        85.98        67.70        80.35
 
 Number of clean counts accepted  :          431
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          188
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s000402h.unf
-> Extracting ad10010060s000402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:12:54    0.72E+02     3739 1000
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000402h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s000402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10010060s000402h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060s000502m.unf
-> Extracting ad10010060s000502m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  22:42:52    0.75E+03     2499 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s000502m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2499      2499              0         0         0         0
 Writing events file
   2499 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2499      2499              0         0         0         0
   in  498.13     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s000502m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10010060s000502m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s000502m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2499
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              63        1375
 Flickering pixels iter, pixels & cnts :   1          13          79
cleaning chip # 1
 Hot pixels & counts                   :              19         358
 Flickering pixels iter, pixels & cnts :   1           7          32
cleaning chip # 2
 Hot pixels & counts                   :              12         152
 Flickering pixels iter, pixels & cnts :   1           8          33
cleaning chip # 3
 Hot pixels & counts                   :              16         228
 Flickering pixels iter, pixels & cnts :   1           5          20
 
 Number of pixels rejected           :          143
 Number of (internal) image counts   :         2499
 Number of image cts rejected (N, %) :         227791.12
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            76           26           20           21
 
 Image counts      :          1537          426          248          288
 Image cts rejected:          1454          390          185          248
 Image cts rej (%) :         94.60        91.55        74.60        86.11
 
    filtering data...
 
 Total counts      :          1537          426          248          288
 Total cts rejected:          1454          390          185          248
 Total cts rej (%) :         94.60        91.55        74.60        86.11
 
 Number of clean counts accepted  :          222
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          143
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s100102h.unf
-> Extracting ad10010060s100102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:13:00    0.18E+04   280333 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100102h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100102h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060s100202h.unf
-> Extracting ad10010060s100202h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:39:26    0.66E+03   146140 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100202h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100202h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100202h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060s100302m.unf
-> Extracting ad10010060s100302m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  23:50:26    0.45E+03    14208 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100302m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100302m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10010060s100302m.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060s100402h.unf
-> Extracting ad10010060s100402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-07  23:05:56    0.10E+04     7539 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100402h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7539      1139              0      6400         0         0
 Writing events file
   1139 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7539      1139              0      6400         0         0
   in  130.15     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10010060s100402h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s100402h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1139
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              14          90
 Flickering pixels iter, pixels & cnts :   1           6          19
cleaning chip # 1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          27         136
cleaning chip # 2
 Hot pixels & counts                   :              21         136
 Flickering pixels iter, pixels & cnts :   1           1           4
cleaning chip # 3
 Hot pixels & counts                   :              16         104
 Flickering pixels iter, pixels & cnts :   1          10          34
 
 Number of pixels rejected           :           95
 Number of (internal) image counts   :         1139
 Number of image cts rejected (N, %) :          52345.92
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            20           27           22           26
 
 Image counts      :           185          551          205          198
 Image cts rejected:           109          136          140          138
 Image cts rej (%) :         58.92        24.68        68.29        69.70
 
    filtering data...
 
 Total counts      :           185          551          205          198
 Total cts rejected:           109          136          140          138
 Total cts rej (%) :         58.92        24.68        68.29        69.70
 
 Number of clean counts accepted  :          616
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           95
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s100502h.unf
-> Extracting ad10010060s100502h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      HIGH        1993-04-08  00:26:40    0.47E+03     2624 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100502h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2624      2624              0         0         0         0
 Writing events file
   2624 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2624      2624              0         0         0         0
   in  468.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100502h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10010060s100502h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s100502h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2624
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              19         406
 Flickering pixels iter, pixels & cnts :   1          16          65
cleaning chip # 1
 Hot pixels & counts                   :              25         637
 Flickering pixels iter, pixels & cnts :   1          12          58
cleaning chip # 2
 Hot pixels & counts                   :              26         626
 Flickering pixels iter, pixels & cnts :   1           5          24
cleaning chip # 3
 Hot pixels & counts                   :              28         608
 Flickering pixels iter, pixels & cnts :   1          10          60
 
 Number of pixels rejected           :          141
 Number of (internal) image counts   :         2624
 Number of image cts rejected (N, %) :         248494.66
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            35           37           31           38
 
 Image counts      :           506          724          682          712
 Image cts rejected:           471          695          650          668
 Image cts rej (%) :         93.08        95.99        95.31        93.82
 
    filtering data...
 
 Total counts      :           506          724          682          712
 Total cts rejected:           471          695          650          668
 Total cts rej (%) :         93.08        95.99        95.31        93.82
 
 Number of clean counts accepted  :          140
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          141
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s100512h.unf
-> Extracting ad10010060s100512h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT2     HIGH        1993-04-08  00:26:40    0.47E+03     2763 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100512h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2763      2763              0         0         0         0
 Writing events file
   2763 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2763      2763              0         0         0         0
   in  468.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100512h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad10010060s100512h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s100512h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2763
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              19         409
 Flickering pixels iter, pixels & cnts :   1          17          68
cleaning chip # 1
 Hot pixels & counts                   :              25         639
 Flickering pixels iter, pixels & cnts :   1          12          59
cleaning chip # 2
 Hot pixels & counts                   :              26         628
 Flickering pixels iter, pixels & cnts :   1           5          24
cleaning chip # 3
 Hot pixels & counts                   :              31         678
 Flickering pixels iter, pixels & cnts :   1           8          45
 
 Number of pixels rejected           :          143
 Number of (internal) image counts   :         2763
 Number of image cts rejected (N, %) :         255092.29
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            36           37           31           39
 
 Image counts      :           525          748          705          785
 Image cts rejected:           477          698          652          723
 Image cts rej (%) :         90.86        93.32        92.48        92.10
 
    filtering data...
 
 Total counts      :           525          748          705          785
 Total cts rejected:           477          698          652          723
 Total cts rej (%) :         90.86        93.32        92.48        92.10
 
 Number of clean counts accepted  :          213
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          143
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060s100602m.unf
-> Extracting ad10010060s100602m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 CRAB        BRIGHT      MEDIUM      1993-04-07  22:42:52    0.75E+03     2455 1111
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060s100602m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2455      2455              0         0         0         0
 Writing events file
   2455 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2455      2455              0         0         0         0
   in  498.13     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060s100602m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10010060s100602m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad10010060s100602m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2455
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              15         322
 Flickering pixels iter, pixels & cnts :   1          21          90
cleaning chip # 1
 Hot pixels & counts                   :              26         621
 Flickering pixels iter, pixels & cnts :   1          10          49
cleaning chip # 2
 Hot pixels & counts                   :              25         560
 Flickering pixels iter, pixels & cnts :   1           6          33
cleaning chip # 3
 Hot pixels & counts                   :              24         480
 Flickering pixels iter, pixels & cnts :   1           8          39
 
 Number of pixels rejected           :          135
 Number of (internal) image counts   :         2455
 Number of image cts rejected (N, %) :         219489.37
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            36           36           31           32
 
 Image counts      :           473          730          660          592
 Image cts rejected:           412          670          593          519
 Image cts rej (%) :         87.10        91.78        89.85        87.67
 
    filtering data...
 
 Total counts      :           473          730          660          592
 Total cts rejected:           412          670          593          519
 Total cts rej (%) :         87.10        91.78        89.85        87.67
 
 Number of clean counts accepted  :          261
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          135
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad10010060g200170h.unf
-> Extracting ad10010060g200170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10010060g200170h.drk since it contains 0 events
-> Extracting ad10010060g200170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:32    0.80E+03   102144     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10010060g200170h.brt since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060g200270h.unf
-> Extracting ad10010060g200270h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.17E+04    98048     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          98048       957              0     97091         0         0
 Writing events file
    957 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98048       957              0     97091         0         0
   in  472.02     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad10010060g200270h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:30    0.17E+04    98048     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          98048      1602              0     96446         0         0
 Writing events file
   1602 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         98048      1602              0     96446         0         0
   in  479.98     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10010060g200370h.unf
-> Extracting ad10010060g200370h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73729     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10010060g200370h.drk since it contains 0 events
-> Extracting ad10010060g200370h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73729     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g200370h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g200370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10010060g200370h.brt since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060g300170h.unf
-> Extracting ad10010060g300170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10010060g300170h.drk since it contains 0 events
-> Extracting ad10010060g300170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:36:34    0.80E+03   101888     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10010060g300170h.brt since it contains 0 events
-> Extracting bright and dark Earth events from ad10010060g300270h.unf
-> Extracting ad10010060g300270h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.17E+04    97559     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          97559       835              0     96724         0         0
 Writing events file
    835 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97559       835              0     96724         0         0
   in  472.02     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad10010060g300270h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:14:32    0.17E+04    97559     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300270h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          97559      1491              0     96068         0         0
 Writing events file
   1491 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97559      1491              0     96068         0         0
   in  479.98     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300270h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10010060g300370h.unf
-> Extracting ad10010060g300370h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73983     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10010060g300370h.drk since it contains 0 events
-> Extracting ad10010060g300370h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 CRAB        PH          HIGH        1993-04-07  23:26:56    0.58E+03    73983     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data24/seq_proc/ad0_10010060.015/ad10010060g300370h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data24/seq_proc/ad0_10010060.015/
Setting mkf directory to /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA > read events ad10010060g300370h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data24/seq_proc/ad0_10010060.015/
HK Directory is: /data/data24/seq_proc/ad0_10010060.015/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10010060g300370h.brt since it contains 0 events

Determining information about this observation (16:55:1)

-> Calculating ISAS time for sis
-> Calculating ISAS time for gis
-> Recording dates of PI calibration files
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory

Generating event file information page (16:56:29)

-> Summing time and events for s0 event files
-> Standard Output From STOOL get_uniq_keys:
ad10010060s000302h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad10010060s000402h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad10010060s000302h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s000402h.unf|S0CCDPOW|1000|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s000302h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4
ad10010060s000402h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4
ad10010060s000302h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order
ad10010060s000402h.unf|S0CCDLST|0 0 0 0|S0 CCD readout order
ad10010060s000302h.unf|S0_SPTR0|40|split threshold level
ad10010060s000402h.unf|S0_SPTR0|20|S0 split threshold for ccd 0
ad10010060s000302h.unf|ORIGMODE|FAINT|DATAMODE before any conversion
ad10010060s000402h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion
-> listing ad10010060s000302h.unf
-> listing ad10010060s000402h.unf
-> listing ad10010060s000502m.unf
-> listing ad10010060s000312h.unf
-> listing ad10010060s000301h.unf
-> listing ad10010060s000601m.unf
-> listing ad10010060s000103h.unf
-> listing ad10010060s000203m.unf
-> Summing time and events for s1 event files
-> Standard Output From STOOL get_uniq_keys:
ad10010060s100102h.unf|S1_ARENA|1|S1 Area discrimination enable/disable
ad10010060s100202h.unf|S1_ARENA|1|S1 Area discrimination enable/disable
ad10010060s100402h.unf|S1_ARENA|0|S1 Area discrimination enable/disable
ad10010060s100502h.unf|S1_ARENA|0|S1 Area discrimination enable/disable
ad10010060s100102h.unf|S1_STAH0|6|S1 area discrimination H start addr for ccd 0
ad10010060s100402h.unf|S1_STAH0|344|S1 area discrimination H start addr for ccd 0
ad10010060s100502h.unf|S1_STAH0|6|S1 area discrimination H start addr for ccd 0
ad10010060s100102h.unf|S1_STAH3|207|S1 area discrimination H start addr for ccd 3
ad10010060s100202h.unf|S1_STAH3|226|S1 area discrimination H start addr for ccd 3
ad10010060s100402h.unf|S1_STAH3|6|S1 area discrimination H start addr for ccd 3
ad10010060s100502h.unf|S1_STAH3|226|S1 area discrimination H start addr for ccd 3
ad10010060s100102h.unf|S1_ENDH0|7|S1 area discrimination H end addr for ccd 0
ad10010060s100402h.unf|S1_ENDH0|425|S1 area discrimination H end addr for ccd 0
ad10010060s100502h.unf|S1_ENDH0|7|S1 area discrimination H end addr for ccd 0
ad10010060s100102h.unf|S1_ENDH3|356|S1 area discrimination H end addr for ccd 3
ad10010060s100202h.unf|S1_ENDH3|337|S1 area discrimination H end addr for ccd 3
ad10010060s100402h.unf|S1_ENDH3|7|S1 area discrimination H end addr for ccd 3
ad10010060s100502h.unf|S1_ENDH3|337|S1 area discrimination H end addr for ccd 3
ad10010060s100102h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100202h.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100402h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100502h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100102h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100202h.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100402h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100502h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100102h.unf|S1CCDLST|0 1 2 3|S1 CCD readout order
ad10010060s100202h.unf|S1CCDLST|3 3 3 3|S1 CCD readout order
ad10010060s100402h.unf|S1CCDLST|0 1 2 3|S1 CCD readout order
ad10010060s100502h.unf|S1CCDLST|0 1 2 3|S1 CCD readout order
ad10010060s100102h.unf|S1_STAV3|211|S1 area discrimination V start addr for ccd 3
ad10010060s100202h.unf|S1_STAV3|230|S1 area discrimination V start addr for ccd 3
ad10010060s100402h.unf|S1_STAV3|2|S1 area discrimination V start addr for ccd 3
ad10010060s100502h.unf|S1_STAV3|230|S1 area discrimination V start addr for ccd 3
ad10010060s100102h.unf|S1_ENDV0|3|S1 area discrimination V end addr for ccd 0
ad10010060s100402h.unf|S1_ENDV0|184|S1 area discrimination V end addr for ccd 0
ad10010060s100502h.unf|S1_ENDV0|3|S1 area discrimination V end addr for ccd 0
ad10010060s100102h.unf|S1_ENDV3|360|S1 area discrimination V end addr for ccd 3
ad10010060s100202h.unf|S1_ENDV3|341|S1 area discrimination V end addr for ccd 3
ad10010060s100402h.unf|S1_ENDV3|3|S1 area discrimination V end addr for ccd 3
ad10010060s100502h.unf|S1_ENDV3|341|S1 area discrimination V end addr for ccd 3
ad10010060s100102h.unf|S1_SPTR0|20|S1 split threshold for ccd 0
ad10010060s100402h.unf|S1_SPTR0|20|S1 split threshold for ccd 0
ad10010060s100502h.unf|S1_SPTR0|40|split threshold level
ad10010060s100102h.unf|S1_SPTR1|20|S1 split threshold for ccd 1
ad10010060s100402h.unf|S1_SPTR1|20|S1 split threshold for ccd 1
ad10010060s100502h.unf|S1_SPTR1|40|split threshold level
ad10010060s100102h.unf|S1_SPTR2|20|S1 split threshold for ccd 2
ad10010060s100402h.unf|S1_SPTR2|20|S1 split threshold for ccd 2
ad10010060s100502h.unf|S1_SPTR2|40|split threshold level
ad10010060s100102h.unf|S1_SPTR3|20|S1 split threshold for ccd 3
ad10010060s100202h.unf|S1_SPTR3|20|S1 split threshold for ccd 3
ad10010060s100402h.unf|S1_SPTR3|20|S1 split threshold for ccd 3
ad10010060s100502h.unf|S1_SPTR3|40|split threshold level
ad10010060s100102h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion
ad10010060s100202h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion
ad10010060s100402h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion
ad10010060s100502h.unf|ORIGMODE|FAINT|DATAMODE before any conversion
-> listing ad10010060s100102h.unf
-> listing ad10010060s100202h.unf
-> listing ad10010060s100402h.unf
-> listing ad10010060s100502h.unf
-> Standard Output From STOOL get_uniq_keys:
ad10010060s100302m.unf|S1_ARENA|1|S1 Area discrimination enable/disable
ad10010060s100602m.unf|S1_ARENA|0|S1 Area discrimination enable/disable
ad10010060s100302m.unf|S1_STAH3|226|S1 area discrimination H start addr for ccd 3
ad10010060s100602m.unf|S1_STAH3|6|S1 area discrimination H start addr for ccd 3
ad10010060s100302m.unf|S1_ENDH3|337|S1 area discrimination H end addr for ccd 3
ad10010060s100602m.unf|S1_ENDH3|7|S1 area discrimination H end addr for ccd 3
ad10010060s100302m.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100602m.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad10010060s100302m.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100602m.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad10010060s100302m.unf|S1CCDLST|3 3 3 3|S1 CCD readout order
ad10010060s100602m.unf|S1CCDLST|0 1 2 3|S1 CCD readout order
ad10010060s100302m.unf|S1_STAV3|230|S1 area discrimination V start addr for ccd 3
ad10010060s100602m.unf|S1_STAV3|2|S1 area discrimination V start addr for ccd 3
ad10010060s100302m.unf|S1_ENDV3|341|S1 area discrimination V end addr for ccd 3
ad10010060s100602m.unf|S1_ENDV3|3|S1 area discrimination V end addr for ccd 3
-> listing ad10010060s100302m.unf
-> listing ad10010060s100602m.unf
-> listing ad10010060s100512h.unf
-> listing ad10010060s100501h.unf
-> listing ad10010060s100701m.unf
-> Summing time and events for g2 event files
-> Standard Output From STOOL get_uniq_keys:
ad10010060g200170h.unf|RBM_AUTO|OFF|RBM auto flag on/off
ad10010060g200270h.unf|RBM_AUTO|ON|RBM auto flag on/off
ad10010060g200370h.unf|RBM_AUTO|OFF|RBM auto flag on/off
ad10010060g200170h.unf|POS_DET|POW2|Position determination method (FLF/POW2)
ad10010060g200270h.unf|POS_DET|FLF|Position determination method (FLF/POW2)
ad10010060g200370h.unf|POS_DET|FLF|Position determination method (FLF/POW2)
-> listing ad10010060g200170h.unf
-> listing ad10010060g200270h.unf
-> listing ad10010060g200370h.unf
-> Summing time and events for g3 event files
-> Standard Output From STOOL get_uniq_keys:
ad10010060g300170h.unf|RBM_AUTO|OFF|RBM auto flag on/off
ad10010060g300270h.unf|RBM_AUTO|ON|RBM auto flag on/off
ad10010060g300370h.unf|RBM_AUTO|OFF|RBM auto flag on/off
ad10010060g300170h.unf|POS_DET|POW2|Position determination method (FLF/POW2)
ad10010060g300270h.unf|POS_DET|FLF|Position determination method (FLF/POW2)
ad10010060g300370h.unf|POS_DET|FLF|Position determination method (FLF/POW2)
-> listing ad10010060g300170h.unf
-> listing ad10010060g300270h.unf
-> listing ad10010060g300370h.unf

Creating HTML header page (17:3:8)

Creating HTML source list (17:3:25)

Doing final wrapup of all files (17:5:21)

-> Copying job.par to ad10010060_015_job.par
-> Copying ad0.par to ad10010060_015_process.par
-> Creating ad10010060_tape.cat
-> Creating ad10010060_trend.cat
-> Creating ad10010060_015_file_info.html
-> Calculating site-independant checksums
-> Site independant checksum: 15878
-> Updating FITS checksum keywords
-> Running fverify on all FITS files

Processing complete (17:21:49)