The following information is also available:
Time column is TIME ORDERED-> Fetching fa930419_2048.2215.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 9406138.986100 9411338.967600
Data file start and stop ascatime : 9406138.986100 9411338.967600
Aspecting run start and stop ascatime : 9406138.986205 9411338.967495
Time interval averaged over (seconds) : 5199.981290
Total pointing and manuver time (sec) : 3396.487793 1803.492798
Mean boresight Euler angles : 278.849276 51.317154 20.766154
RA DEC SUN ANGLE
Mean solar position (deg) : 26.81 11.07
Mean aberration (arcsec) : 9.27 -16.70
Mean sat X-axis (deg) : 310.094167 -46.878430 89.20
Mean sat Y-axis (deg) : 22.182170 16.067619 6.73
Mean sat Z-axis (deg) : 278.849276 38.682845 96.68
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 279.091125 38.895603 290.615295 0.156983
Minimum 279.085602 38.894783 290.535767 0.000000
Maximum 279.097198 38.914669 290.626282 1.172723
Sigma (RMS) 0.000832 0.000070 0.007318 0.109944
Number of ASPECT records processed = 7564
Aspecting to RA/DEC : 279.09112549 38.89560318
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 279.091 DEC: 38.896
START TIME: SC 9406138.9862 = UT 19/04/93 20:48:58
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000123 0.731 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1911.993286 0.200 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
5199.981445 1.173 5003 1 1 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0
Attitude Records: 7564
Attitude Steps: 3
Maneuver ACM time: 1803.50 sec
Pointed ACM time: 3396.50 sec
-> Calculating aspect point97 99 count=1290 sum1=359706 sum2=66198 sum3=26794.6 98 97 count=1 sum1=278.844 sum2=51.298 sum3=20.748 98 99 count=5960 sum1=1.66194e+06 sum2=305850 sum3=123769 99 99 count=308 sum1=85887.2 sum2=15805.6 sum3=6391.89 99 100 count=2 sum1=557.725 sum2=102.647 sum3=41.381 100 100 count=2 sum1=557.728 sum2=102.647 sum3=41.378 0 out of 7563 points outside bin structure-> Euler angles: 278.847, 51.3169, 20.7674
Interpolating 2 records in time interval 9.41133e+06 - 9.41134e+06
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft930419_2048.2215",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft930419_2048.2215 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 93760 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 27264 PH = 121024 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 1894 no. of SIS events found = 163417-> Standard Error Output From FTOOL frfread
coordinate error 84 457-> Removing the following files with NEVENTS=0
ft930419_2048_2215G200170M.fits ft930419_2048_2215G200299.fits ft930419_2048_2215G200770H.fits ft930419_2048_2215G200870H.fits ft930419_2048_2215G200970M.fits ft930419_2048_2215G201070M.fits ft930419_2048_2215G300170M.fits ft930419_2048_2215G300299.fits ft930419_2048_2215G300570H.fits ft930419_2048_2215G301070H.fits ft930419_2048_2215G301170M.fits ft930419_2048_2215G301270M.fits ft930419_2048_2215S000101M.fits ft930419_2048_2215S000299.fits ft930419_2048_2215S000401H.fits ft930419_2048_2215S000701M.fits ft930419_2048_2215S100101M.fits ft930419_2048_2215S100299.fits ft930419_2048_2215S100407H.fits ft930419_2048_2215S100701M.fits-> Checking for empty GTI extensions
ft930419_2048_2215S000301H.fits[3] ft930419_2048_2215S000501H.fits[3] ft930419_2048_2215S000601M.fits[3]-> Merging GTIs from the following files:
ft930419_2048_2215S100301H.fits[3] ft930419_2048_2215S100501H.fits[3] ft930419_2048_2215S100601M.fits[3]-> Merging GTIs from the following files:
ft930419_2048_2215G200370H.fits[3] ft930419_2048_2215G200470H.fits[3] ft930419_2048_2215G200570H.fits[3] ft930419_2048_2215G200670H.fits[3]-> Merging GTIs from the following files:
ft930419_2048_2215G300370H.fits[3] ft930419_2048_2215G300470H.fits[3] ft930419_2048_2215G300670H.fits[3] ft930419_2048_2215G300770H.fits[3] ft930419_2048_2215G300870H.fits[3] ft930419_2048_2215G300970H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 8291 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:Total filenames split = 4 GISSORTSPLIT:LO:Total split file cnt = 4 GISSORTSPLIT:LO:End program-> Creating ad10013020g200170h.unf
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930419_2048_2215G200670H.fits Merging binary extension #: 2 1 -- ft930419_2048_2215G200670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000005 events
ft930419_2048_2215G200570H.fits-> Ignoring the following files containing 000000004 events
ft930419_2048_2215G200470H.fits-> Ignoring the following files containing 000000003 events
ft930419_2048_2215G200370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300270h.prelist merge count = 2 photon cnt = 8018 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:Total filenames split = 6 GISSORTSPLIT:LO:Total split file cnt = 5 GISSORTSPLIT:LO:End program-> Creating ad10013020g300170h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930419_2048_2215G300670H.fits 2 -- ft930419_2048_2215G300870H.fits Merging binary extension #: 2 1 -- ft930419_2048_2215G300670H.fits 2 -- ft930419_2048_2215G300870H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000008 events
ft930419_2048_2215G300770H.fits-> Ignoring the following files containing 000000005 events
ft930419_2048_2215G300370H.fits-> Ignoring the following files containing 000000003 events
ft930419_2048_2215G300470H.fits-> Ignoring the following files containing 000000001 events
ft930419_2048_2215G300970H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 2 photon cnt = 84941 SIS0SORTSPLIT:LO:s000201m.prelist merge count = 1 photon cnt = 192 SIS0SORTSPLIT:LO:Total filenames split = 3 SIS0SORTSPLIT:LO:Total split file cnt = 2 SIS0SORTSPLIT:LO:End program-> Creating ad10013020s000101h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930419_2048_2215S000301H.fits 2 -- ft930419_2048_2215S000501H.fits Merging binary extension #: 2 1 -- ft930419_2048_2215S000301H.fits 2 -- ft930419_2048_2215S000501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000192 events
ft930419_2048_2215S000601M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 2 photon cnt = 78091 SIS1SORTSPLIT:LO:s100201m.prelist merge count = 1 photon cnt = 192 SIS1SORTSPLIT:LO:Total filenames split = 3 SIS1SORTSPLIT:LO:Total split file cnt = 2 SIS1SORTSPLIT:LO:End program-> Creating ad10013020s100101h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930419_2048_2215S100301H.fits 2 -- ft930419_2048_2215S100501H.fits Merging binary extension #: 2 1 -- ft930419_2048_2215S100301H.fits 2 -- ft930419_2048_2215S100501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000192 events
ft930419_2048_2215S100601M.fits-> Tar-ing together the leftover raw files
a ft930419_2048_2215G200370H.fits 40K a ft930419_2048_2215G200470H.fits 40K a ft930419_2048_2215G200570H.fits 40K a ft930419_2048_2215G300370H.fits 40K a ft930419_2048_2215G300470H.fits 40K a ft930419_2048_2215G300770H.fits 40K a ft930419_2048_2215G300970H.fits 40K a ft930419_2048_2215S000601M.fits 45K a ft930419_2048_2215S100601M.fits 45K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft930419_2048.2215 'ft930419_2048.2215' is successfully opened Data Start Time is 9406136.99 (930419 204856) Time Margin 2.0 sec included 'ft930419_2048.2215' EOF detected, sf=1894 Data End Time is 9411340.97 (930419 221540) Gain History is written in ft930419_2048_2215.ghf-> Checking if column CAL_START in ft930419_2048_2215.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft930419_2048_2215.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad10013020g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10013020s100112h.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 93/ 4/19 20:48 mjd=49096.866667 Orbit file name is ./frf.orbit.201 Epoch of Orbital Elements: 1993/4/13 0:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa930419_2048.2215 S0-HK file: ft930419_2048_2215S0HK.fits S1-HK file: ft930419_2048_2215S1HK.fits G2-HK file: ft930419_2048_2215G2HK.fits G3-HK file: ft930419_2048_2215G3HK.fits output FITS File: ft930419_2048_2215.mkf Total 164 Data bins were processed.-> Checking if column TIME in ft930419_2048_2215.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 799.16544 The mean of the selected column is 17.373162 The standard deviation of the selected column is 5.4101137 The minimum of selected column is 9.1875334 The maximum of selected column is 32.062618 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 589.53970 The mean of the selected column is 12.816081 The standard deviation of the selected column is 4.4588727 The minimum of selected column is 4.9125323 The maximum of selected column is 25.375092 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 814.37804 The mean of the selected column is 17.703871 The standard deviation of the selected column is 6.2143596 The minimum of selected column is 5.8125210 The maximum of selected column is 33.000118 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 811.61867 The mean of the selected column is 17.643884 The standard deviation of the selected column is 6.3109844 The minimum of selected column is 5.3125196 The maximum of selected column is 32.687618 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.1 && S0_PIXL0<33.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<26.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<36.3 )&& (S0_PIXL3>0.0 && S0_PIXL3<36.5 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.27E+04 8396 1111
Processing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
8154 6992 0 1162 0 0
Writing events file
6992 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8154 6992 0 1162 0 0
in 1515.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/10013020.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/10013020.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 6992
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 57 4923
Flickering pixels iter, pixels & cnts : 1 12 137
cleaning chip # 1
Hot pixels & counts : 10 738
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
Hot pixels & counts : 6 319
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 3
Hot pixels & counts : 7 500
Flickering pixels iter, pixels & cnts : 1 3 13
Number of pixels rejected : 97
Number of (internal) image counts : 6992
Number of image cts rejected (N, %) : 6636 94.9084702
By chip : 0 1 2 3
Pixels rejected : 69 11 7 10
Image counts : 5149 828 420 595
Image cts rejected: 5060 741 322 513
Image cts rej (%) : 98.27 89.49 76.67 86.22
filtering data...
Total counts : 5149 828 420 595
Total cts rejected: 5060 741 322 513
Total cts rej (%) : 98.27 89.49 76.67 86.22
Number of clean counts accepted : 356
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 97
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10013020s000102h.evt use_events=no
Wrote cleaned events file to ad10013020s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad10013020s000112h.unf into ad10013020s000112h.evtThe sum of the selected column is 799.16544 The mean of the selected column is 17.373162 The standard deviation of the selected column is 5.4101137 The minimum of selected column is 9.1875334 The maximum of selected column is 32.062618 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 589.53970 The mean of the selected column is 12.816081 The standard deviation of the selected column is 4.4588727 The minimum of selected column is 4.9125323 The maximum of selected column is 25.375092 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 814.37804 The mean of the selected column is 17.703871 The standard deviation of the selected column is 6.2143596 The minimum of selected column is 5.8125210 The maximum of selected column is 33.000118 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 811.61867 The mean of the selected column is 17.643884 The standard deviation of the selected column is 6.3109844 The minimum of selected column is 5.3125196 The maximum of selected column is 32.687618 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.1 && S0_PIXL0<33.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<26.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<36.3 )&& (S0_PIXL3>0.0 && S0_PIXL3<36.5 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.27E+04 9144 1111
Processing file: /data/data19/seq_proc/10013020.008/ad10013020s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
8218 7011 0 1207 0 0
Writing events file
7011 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8218 7011 0 1207 0 0
in 1515.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/10013020.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/10013020.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 7011
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 57 4925
Flickering pixels iter, pixels & cnts : 1 12 137
cleaning chip # 1
Hot pixels & counts : 10 738
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
Hot pixels & counts : 6 319
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 3
Hot pixels & counts : 7 500
Flickering pixels iter, pixels & cnts : 1 3 13
Number of pixels rejected : 97
Number of (internal) image counts : 7011
Number of image cts rejected (N, %) : 6638 94.6797867
By chip : 0 1 2 3
Pixels rejected : 69 11 7 10
Image counts : 5158 829 424 600
Image cts rejected: 5062 741 322 513
Image cts rej (%) : 98.14 89.38 75.94 85.50
filtering data...
Total counts : 5158 829 424 600
Total cts rejected: 5062 741 322 513
Total cts rej (%) : 98.14 89.38 75.94 85.50
Number of clean counts accepted : 373
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 97
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad10013020s000112h.evt use_events=no
Wrote cleaned events file to ad10013020s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad10013020s100101h.unf because of modeThe sum of the selected column is 1077.6696 The mean of the selected column is 23.427600 The standard deviation of the selected column is 10.647409 The minimum of selected column is 5.4062891 The maximum of selected column is 49.593933 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1205.0638 The mean of the selected column is 26.197040 The standard deviation of the selected column is 10.044484 The minimum of selected column is 5.7031665 The maximum of selected column is 48.187675 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1023.7652 The mean of the selected column is 22.255766 The standard deviation of the selected column is 9.2832037 The minimum of selected column is 6.5500236 The maximum of selected column is 43.000156 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1095.7790 The mean of the selected column is 23.821283 The standard deviation of the selected column is 11.930549 The minimum of selected column is 9.5625343 The maximum of selected column is 84.250313 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<55.3 )&& (S1_PIXL1>0.0 && S1_PIXL1<56.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<50.1 )&& (S1_PIXL3>0.0 && S1_PIXL3<59.6 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.27E+04 10316 1111
Processing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9580 5556 0 4024 0 0
Writing events file
5556 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9580 5556 0 4024 0 0
in 1479.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/10013020.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/10013020.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 5556
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 816
Flickering pixels iter, pixels & cnts : 1 3 9
cleaning chip # 1
Hot pixels & counts : 21 1583
Flickering pixels iter, pixels & cnts : 1 5 29
cleaning chip # 2
Hot pixels & counts : 18 1312
Flickering pixels iter, pixels & cnts : 1 3 23
cleaning chip # 3
Hot pixels & counts : 19 1415
Flickering pixels iter, pixels & cnts : 1 5 23
Number of pixels rejected : 85
Number of (internal) image counts : 5556
Number of image cts rejected (N, %) : 5210 93.7724991
By chip : 0 1 2 3
Pixels rejected : 14 26 21 24
Image counts : 912 1710 1417 1517
Image cts rejected: 825 1612 1335 1438
Image cts rej (%) : 90.46 94.27 94.21 94.79
filtering data...
Total counts : 912 1710 1417 1517
Total cts rejected: 825 1612 1335 1438
Total cts rej (%) : 90.46 94.27 94.21 94.79
Number of clean counts accepted : 346
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 85
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10013020s100102h.evt use_events=no
Wrote cleaned events file to ad10013020s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad10013020s100112h.unf into ad10013020s100112h.evtThe sum of the selected column is 1077.6696 The mean of the selected column is 23.427600 The standard deviation of the selected column is 10.647409 The minimum of selected column is 5.4062891 The maximum of selected column is 49.593933 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1205.0638 The mean of the selected column is 26.197040 The standard deviation of the selected column is 10.044484 The minimum of selected column is 5.7031665 The maximum of selected column is 48.187675 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1023.7652 The mean of the selected column is 22.255766 The standard deviation of the selected column is 9.2832037 The minimum of selected column is 6.5500236 The maximum of selected column is 43.000156 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1095.7790 The mean of the selected column is 23.821283 The standard deviation of the selected column is 11.930549 The minimum of selected column is 9.5625343 The maximum of selected column is 84.250313 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<55.3 )&& (S1_PIXL1>0.0 && S1_PIXL1<56.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<50.1 )&& (S1_PIXL3>0.0 && S1_PIXL3<59.6 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.27E+04 11060 1111
Processing file: /data/data19/seq_proc/10013020.008/ad10013020s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9633 5582 0 4051 0 0
Writing events file
5582 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9633 5582 0 4051 0 0
in 1479.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/10013020.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/10013020.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 5582
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 11 819
Flickering pixels iter, pixels & cnts : 1 3 9
cleaning chip # 1
Hot pixels & counts : 21 1583
Flickering pixels iter, pixels & cnts : 1 5 29
cleaning chip # 2
Hot pixels & counts : 18 1312
Flickering pixels iter, pixels & cnts : 1 3 23
cleaning chip # 3
Hot pixels & counts : 19 1423
Flickering pixels iter, pixels & cnts : 1 5 23
Number of pixels rejected : 85
Number of (internal) image counts : 5582
Number of image cts rejected (N, %) : 5221 93.5327835
By chip : 0 1 2 3
Pixels rejected : 14 26 21 24
Image counts : 918 1714 1425 1525
Image cts rejected: 828 1612 1335 1446
Image cts rej (%) : 90.20 94.05 93.68 94.82
filtering data...
Total counts : 918 1714 1425 1525
Total cts rejected: 828 1612 1335 1446
Total cts rej (%) : 90.20 94.05 93.68 94.82
Number of clean counts accepted : 361
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 85
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad10013020s100112h.evt use_events=no
Wrote cleaned events file to ad10013020s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad10013020g200170h.unf into ad10013020g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8291 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.unf
Total Good Bad: Region Time Phase Cut
8291 787 6254 1250 0 0
Writing events file
787 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8291 787 6254 1250 0 0
in 2658.01 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
787 686 101
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10013020g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 686 in ad10013020g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8018 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.unf
Total Good Bad: Region Time Phase Cut
8018 685 6270 1063 0 0
Writing events file
685 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8018 685 6270 1063 0 0
in 2658.01 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
685 590 95
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!screen:ASCA > read events ad10013020g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10013020g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 590 in ad10013020g300170h.unf-ANNULUS(128.5,128.5,192,81) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad10013020g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930419_2048.2215
making an exposure map...
Aspect RA/DEC/ROLL : 279.0890 38.8959 290.6170
Mean RA/DEC/ROLL : 279.0905 38.8683 290.6170
Pnt RA/DEC/ROLL : 279.0824 38.9201 290.6170
Image rebin factor : 1
Attitude Records : 7567
GTI intervals : 4
Total GTI (secs) : 2658.013
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 503.4981689 503.4981689
20 Percent Complete: Total/live time: 885.4967041 885.4967041
30 Percent Complete: Total/live time: 885.4967041 885.4967041
40 Percent Complete: Total/live time: 1307.4952393 1307.4952393
50 Percent Complete: Total/live time: 2003.5021973 2003.5021973
60 Percent Complete: Total/live time: 2003.5021973 2003.5021973
70 Percent Complete: Total/live time: 2564.5002441 2564.5002441
80 Percent Complete: Total/live time: 2564.5002441 2564.5002441
90 Percent Complete: Total/live time: 2658.0134277 2658.0134277
100 Percent Complete: Total/live time: 2658.0134277 2658.0134277
Number of attitude steps used: 7
Number of attitude steps avail: 5497
Mean RA/DEC pixel offset: -11.3392 -2.7454
writing expo file: ad10013020g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10013020g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10013020g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
in 2658.01 seconds
Image has 686 counts for 0.2581 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 361 0 0 0 325
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 361 0 0 0 325
in 2658.01 seconds
Image has 361 counts for 0.1358 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 326 0 0 0 360
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 326 0 0 0 360
in 2658.01 seconds
Image has 326 counts for 0.1226 counts/sec
Command not found; type ? for a command listing
!ad10013020g200170h:ASCA >
!ad10013020g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10013020g200170h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!ad10013020g200170h:ASCA > read events ad10013020g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!ad10013020g200170h:ASCA-GIS2-PH > set image sky
!ad10013020g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad10013020g200170h:ASCA-GIS2-PH > extract image
!ad10013020g200170h:ASCA-GIS2-PH > save image outfile=ad10013020g200170h.img
Wrote image to file ad10013020g200170h.img
!ad10013020g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10013020g200170h:ASCA-GIS2-PH > extract image
!ad10013020g200170h:ASCA-GIS2-PH > save image outfile=ad10013020g200170h_lo.img
Wrote image to file ad10013020g200170h_lo.img
!ad10013020g200170h:ASCA-GIS2-PH > clear pha_cut
!ad10013020g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10013020g200170h:ASCA-GIS2-PH > extract image
!ad10013020g200170h:ASCA-GIS2-PH > save image outfile=ad10013020g200170h_hi.img
Wrote image to file ad10013020g200170h_hi.img
!ad10013020g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10013020g300170h.expo-ANNULUS(128.5,128.5,192,73) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad10013020g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930419_2048.2215
making an exposure map...
Aspect RA/DEC/ROLL : 279.0890 38.8959 290.6119
Mean RA/DEC/ROLL : 279.0826 38.8923 290.6119
Pnt RA/DEC/ROLL : 279.0907 38.8961 290.6119
Image rebin factor : 1
Attitude Records : 7567
GTI intervals : 4
Total GTI (secs) : 2658.013
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 503.4981689 503.4981689
20 Percent Complete: Total/live time: 885.4967041 885.4967041
30 Percent Complete: Total/live time: 885.4967041 885.4967041
40 Percent Complete: Total/live time: 1307.4952393 1307.4952393
50 Percent Complete: Total/live time: 2003.5021973 2003.5021973
60 Percent Complete: Total/live time: 2003.5021973 2003.5021973
70 Percent Complete: Total/live time: 2564.5002441 2564.5002441
80 Percent Complete: Total/live time: 2564.5002441 2564.5002441
90 Percent Complete: Total/live time: 2658.0134277 2658.0134277
100 Percent Complete: Total/live time: 2658.0134277 2658.0134277
Number of attitude steps used: 7
Number of attitude steps avail: 5497
Mean RA/DEC pixel offset: -0.9861 -1.7169
writing expo file: ad10013020g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10013020g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10013020g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
in 2658.01 seconds
Image has 590 counts for 0.2220 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 309 0 0 0 281
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 309 0 0 0 281
in 2658.01 seconds
Image has 309 counts for 0.1163 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 282 0 0 0 308
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 282 0 0 0 308
in 2658.01 seconds
Image has 282 counts for 0.1061 counts/sec
Command not found; type ? for a command listing
!ad10013020g300170h:ASCA >
!ad10013020g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10013020g300170h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!ad10013020g300170h:ASCA > read events ad10013020g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!ad10013020g300170h:ASCA-GIS3-PH > set image sky
!ad10013020g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad10013020g300170h:ASCA-GIS3-PH > extract image
!ad10013020g300170h:ASCA-GIS3-PH > save image outfile=ad10013020g300170h.img
Wrote image to file ad10013020g300170h.img
!ad10013020g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10013020g300170h:ASCA-GIS3-PH > extract image
!ad10013020g300170h:ASCA-GIS3-PH > save image outfile=ad10013020g300170h_lo.img
Wrote image to file ad10013020g300170h_lo.img
!ad10013020g300170h:ASCA-GIS3-PH > clear pha_cut
!ad10013020g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10013020g300170h:ASCA-GIS3-PH > extract image
!ad10013020g300170h:ASCA-GIS3-PH > save image outfile=ad10013020g300170h_hi.img
Wrote image to file ad10013020g300170h_hi.img
!ad10013020g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10013020s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad10013020s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 350
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 100 50
reading att file: ./fa930419_2048.2215
making an exposure map...
Aspect RA/DEC/ROLL : 279.0890 38.8959 290.6028
Mean RA/DEC/ROLL : 279.0698 38.8752 290.6028
Pnt RA/DEC/ROLL : 279.1052 38.9136 290.6028
Image rebin factor : 4
Attitude Records : 7567
Hot Pixels : 97
GTI intervals : 5
Total GTI (secs) : 1515.935
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 397.9754028 397.9754028
20 Percent Complete: Total/live time: 397.9754028 397.9754028
30 Percent Complete: Total/live time: 929.4240723 929.4240723
40 Percent Complete: Total/live time: 929.4240723 929.4240723
50 Percent Complete: Total/live time: 1515.9345703 1515.9345703
100 Percent Complete: Total/live time: 1515.9345703 1515.9345703
Number of attitude steps used: 6
Number of attitude steps avail: 3662
Mean RA/DEC pixel offset: -56.0904 -74.2529
writing expo file: ad10013020s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10013020s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10013020s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 356 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.evt
Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
in 1515.93 seconds
Image has 356 counts for 0.2348 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.evt
Total Good Bad: Region Time Phase Cut
356 193 0 0 0 163
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
356 193 0 0 0 163
in 1515.93 seconds
Image has 193 counts for 0.1273 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.evt
Total Good Bad: Region Time Phase Cut
356 163 0 0 0 193
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
356 163 0 0 0 193
in 1515.93 seconds
Image has 163 counts for 0.1075 counts/sec
Command not found; type ? for a command listing
!ad10013020s000102h:ASCA >
!ad10013020s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10013020s000102h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!ad10013020s000102h:ASCA > read events ad10013020s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!ad10013020s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad10013020s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad10013020s000102h:ASCA-SIS0-BRIGHT > extract image
!ad10013020s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad10013020s000102h.img
Wrote image to file ad10013020s000102h.img
!ad10013020s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad10013020s000102h:ASCA-SIS0-BRIGHT > extract image
!ad10013020s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad10013020s000102h_lo.img
Wrote image to file ad10013020s000102h_lo.img
!ad10013020s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad10013020s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10013020s000102h:ASCA-SIS0-BRIGHT > extract image
!ad10013020s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad10013020s000102h_hi.img
Wrote image to file ad10013020s000102h_hi.img
!ad10013020s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad10013020s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad10013020s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa930419_2048.2215
making an exposure map...
Aspect RA/DEC/ROLL : 279.0890 38.8959 290.6151
Mean RA/DEC/ROLL : 279.0885 38.8799 290.6151
Pnt RA/DEC/ROLL : 279.0857 38.9089 290.6151
Image rebin factor : 4
Attitude Records : 7567
Hot Pixels : 85
GTI intervals : 5
Total GTI (secs) : 1479.935
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 365.9754028 365.9754028
20 Percent Complete: Total/live time: 365.9754028 365.9754028
30 Percent Complete: Total/live time: 893.4240723 893.4240723
40 Percent Complete: Total/live time: 893.4240723 893.4240723
50 Percent Complete: Total/live time: 1479.9345703 1479.9345703
100 Percent Complete: Total/live time: 1479.9345703 1479.9345703
Number of attitude steps used: 6
Number of attitude steps avail: 3662
Mean RA/DEC pixel offset: -59.7940 -14.3770
writing expo file: ad10013020s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10013020s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10013020s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 346 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.evt
Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
in 1479.93 seconds
Image has 346 counts for 0.2338 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.evt
Total Good Bad: Region Time Phase Cut
346 180 0 0 0 166
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
346 180 0 0 0 166
in 1479.93 seconds
Image has 180 counts for 0.1216 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.evt
Total Good Bad: Region Time Phase Cut
346 167 0 0 0 179
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
346 167 0 0 0 179
in 1479.93 seconds
Image has 167 counts for 0.1128 counts/sec
Command not found; type ? for a command listing
!ad10013020s100102h:ASCA >
!ad10013020s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10013020s100102h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!ad10013020s100102h:ASCA > read events ad10013020s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!ad10013020s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad10013020s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad10013020s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10013020s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10013020s100102h.img
Wrote image to file ad10013020s100102h.img
!ad10013020s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad10013020s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10013020s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10013020s100102h_lo.img
Wrote image to file ad10013020s100102h_lo.img
!ad10013020s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad10013020s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10013020s100102h:ASCA-SIS1-BRIGHT > extract image
!ad10013020s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad10013020s100102h_hi.img
Wrote image to file ad10013020s100102h_hi.img
!ad10013020s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad10013020s000102h.expo ad10013020s100102h.expo-> Summing the following images to produce ad10013020sis32002_all.totsky
ad10013020s000102h.img ad10013020s100102h.img-> Summing the following images to produce ad10013020sis32002_lo.totsky
ad10013020s000102h_lo.img ad10013020s100102h_lo.img-> Summing the following images to produce ad10013020sis32002_hi.totsky
ad10013020s000102h_hi.img ad10013020s100102h_hi.img-> Running XIMAGE to create ad10013020sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad10013020sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 2.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 2 min: 0 ![2]XIMAGE> read/exp_map ad10013020sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 49.9312 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 49 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 2995 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 84.0000 84 0 ![9]XIMAGE> exit-> Summing gis images
ad10013020g200170h.expo ad10013020g300170h.expo-> Summing the following images to produce ad10013020gis25670_all.totsky
ad10013020g200170h.img ad10013020g300170h.img-> Summing the following images to produce ad10013020gis25670_lo.totsky
ad10013020g200170h_lo.img ad10013020g300170h_lo.img-> Summing the following images to produce ad10013020gis25670_hi.totsky
ad10013020g200170h_hi.img ad10013020g300170h_hi.img-> Running XIMAGE to create ad10013020gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad10013020gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 3.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 3 min: 0 ![2]XIMAGE> read/exp_map ad10013020gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 88.6004 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 88 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 21264 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 10632.0 106 2 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad10013020gis25670.src
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad10013020sis32002.src
1 ad10013020s000102h.evt 356-> Standard Output From STOOL group_event_files:
1 ad10013020s000112h.evt 373-> Standard Output From STOOL group_event_files:
1 ad10013020s100102h.evt 346-> Standard Output From STOOL group_event_files:
1 ad10013020s100112h.evt 361-> Standard Output From STOOL group_event_files:
1 ad10013020g200170h.evt 686-> GIS2_REGION256_OFF.4 already present in current directory
ad10013020g200170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
in 2658.01 seconds
Spectrum has 686 counts for 0.2581 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2658.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.31636 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10013020g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad10013020g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10013020g210170_0.pi group=yes
Wrote spectrum to ad10013020g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad10013020g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad10013020g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2658.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.31636 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 22 are grouped by a factor 23 ... 23 - 36 are grouped by a factor 14 ... 37 - 56 are grouped by a factor 20 ... 57 - 77 are grouped by a factor 21 ... 78 - 113 are grouped by a factor 18 ... 114 - 132 are grouped by a factor 19 ... 133 - 155 are grouped by a factor 23 ... 156 - 180 are grouped by a factor 25 ... 181 - 232 are grouped by a factor 52 ... 233 - 376 are grouped by a factor 72 ... 377 - 423 are grouped by a factor 47 ... 424 - 513 are grouped by a factor 90 ... 514 - 617 are grouped by a factor 104 ... 618 - 793 are grouped by a factor 176 ... 794 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad10013020g210170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 163 by 164 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1250.4 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.86000E+02
Weighted mean angle from optical axis = 13.391 arcmin
-> Standard Output From STOOL group_event_files:1 ad10013020g300170h.evt 590-> GIS3_REGION256_OFF.4 already present in current directory
ad10013020g300170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
in 2658.01 seconds
Spectrum has 590 counts for 0.2220 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2658.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.25945 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10013020g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad10013020g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10013020g310170_0.pi group=yes
Wrote spectrum to ad10013020g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad10013020g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad10013020g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2658.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.25945 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 are grouped by a factor 26 ... 26 - 40 are grouped by a factor 15 ... 41 - 60 are grouped by a factor 20 ... 61 - 81 are grouped by a factor 21 ... 82 - 101 are grouped by a factor 20 ... 102 - 124 are grouped by a factor 23 ... 125 - 153 are grouped by a factor 29 ... 154 - 193 are grouped by a factor 40 ... 194 - 239 are grouped by a factor 46 ... 240 - 300 are grouped by a factor 61 ... 301 - 391 are grouped by a factor 91 ... 392 - 452 are grouped by a factor 61 ... 453 - 629 are grouped by a factor 177 ... 630 - 819 are grouped by a factor 190 ... 820 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad10013020g310170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 147 by 148 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1025.4 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.90000E+02
Weighted mean angle from optical axis = 12.171 arcmin
-> Plotting ad10013020g210170_0_pi.ps from ad10013020g210170_0.pi
XSPEC 9.01 23:15:59 11-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad10013020g210170_0.pi
Net count rate (cts/s) for file 1 0.2581 +/- 1.1255E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad10013020g310170_0_pi.ps from ad10013020g310170_0.pi
XSPEC 9.01 23:16:30 11-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad10013020g310170_0.pi
Net count rate (cts/s) for file 1 0.2220 +/- 1.0467E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 356 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.evt
Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
Writing events file
356 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
in 1515.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10013020s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> skipping ad10013020s000002_0.lc since it would have 356 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 346 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.evt
Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
Writing events file
346 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
in 1479.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS1-BRIGHT > filter region ad10013020s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> skipping ad10013020s100002_0.lc since it would have 346 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
Writing events file
686 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
in 2658.01 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS2-PH > filter region ad10013020g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad10013020g200070_0.lc with binsize 193.732762204499
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/events.tmp
Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
in 2658.01 seconds
Fits light curve has 686 counts for 0.2581 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS2-PH > set binsize 193.732762204499
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad10013020g200070_0.lc
Wrote FITS light curve to file ad10013020g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad10013020g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad10013020g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ VEGA Start Time (d) .... 9096 21:03:12.983
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9096 21:51:54.986
No. of Rows ....... 14 Bin Time (s) ...... 193.7
Right Ascension ... 2.7909E+02 Internal time sys.. Converted to TJD
Declination ....... 3.8896E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 16 Newbins of 193.733 (s)
Intv 1 Start 9096 21: 4:49
Ser.1 Avg 0.2544 Chisq 6.125 Var 0.6237E-03 Newbs. 14
Min 0.2065 Max 0.2938 expVar 0.1426E-02 Bins 14
Results from Statistical Analysis
Newbin Integration Time (s).. 193.73
Interval Duration (s)........ 2712.3
No. of Newbins .............. 14
Average (c/s) ............... 0.25438 +/- 0.10E-01
Standard Deviation (c/s)..... 0.24974E-01
Minimum (c/s)................ 0.20647
Maximum (c/s)................ 0.29384
Variance ((c/s)**2).......... 0.62373E-03 +/- 0.24E-03
Expected Variance ((c/s)**2). 0.14256E-02 +/- 0.56E-03
Third Moment ((c/s)**3)......-0.55750E-05
Average Deviation (c/s)...... 0.19915E-01
Skewness.....................-0.35789 +/- 0.65
Kurtosis.....................-0.82212 +/- 1.3
RMS fractional variation....< 0.21773 (3 sigma)
Chi-Square................... 6.1253 dof 13
Chi-Square Prob of constancy. 0.94147 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.61604 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 16 Newbins of 193.733 (s)
Intv 1 Start 9096 21: 4:49
Ser.1 Avg 0.2544 Chisq 6.125 Var 0.6237E-03 Newbs. 14
Min 0.2065 Max 0.2938 expVar 0.1426E-02 Bins 14
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad10013020g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
Writing events file
590 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
in 2658.01 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS3-PH > filter region ad10013020g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad10013020g300070_0.lc with binsize 225.255381139469
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/events.tmp
Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
in 2658.01 seconds
Fits light curve has 590 counts for 0.2220 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS3-PH > set binsize 225.255381139469
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad10013020g300070_0.lc
Wrote FITS light curve to file ad10013020g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad10013020g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad10013020g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ VEGA Start Time (d) .... 9096 21:03:12.983
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9096 21:51:54.986
No. of Rows ....... 13 Bin Time (s) ...... 225.3
Right Ascension ... 2.7909E+02 Internal time sys.. Converted to TJD
Declination ....... 3.8896E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 13 Newbins of 225.255 (s)
Intv 1 Start 9096 21: 5: 5
Ser.1 Avg 0.2233 Chisq 20.98 Var 0.1884E-02 Newbs. 13
Min 0.1332 Max 0.2900 expVar 0.1167E-02 Bins 13
Results from Statistical Analysis
Newbin Integration Time (s).. 225.26
Interval Duration (s)........ 2703.1
No. of Newbins .............. 13
Average (c/s) ............... 0.22334 +/- 0.99E-02
Standard Deviation (c/s)..... 0.43402E-01
Minimum (c/s)................ 0.13318
Maximum (c/s)................ 0.28996
Variance ((c/s)**2).......... 0.18837E-02 +/- 0.77E-03
Expected Variance ((c/s)**2). 0.11672E-02 +/- 0.48E-03
Third Moment ((c/s)**3)......-0.26036E-04
Average Deviation (c/s)...... 0.35571E-01
Skewness.....................-0.31845 +/- 0.68
Kurtosis.....................-0.63599 +/- 1.4
RMS fractional variation....< 0.15741 (3 sigma)
Chi-Square................... 20.980 dof 12
Chi-Square Prob of constancy. 0.50675E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.83960E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 13 Newbins of 225.255 (s)
Intv 1 Start 9096 21: 5: 5
Ser.1 Avg 0.2233 Chisq 20.98 Var 0.1884E-02 Newbs. 13
Min 0.1332 Max 0.2900 expVar 0.1167E-02 Bins 13
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad10013020g200170h.evt[2]-> Making L1 light curve of ft930419_2048_2215G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 4820 output records from 4824 good input G2_L1 records.-> Making L1 light curve of ft930419_2048_2215G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2323 output records from 4824 good input G2_L1 records.-> Merging GTIs from the following files:
ad10013020g300170h.evt[2]-> Making L1 light curve of ft930419_2048_2215G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 4593 output records from 4597 good input G3_L1 records.-> Making L1 light curve of ft930419_2048_2215G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2259 output records from 4597 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.evt
Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
Writing events file
686 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
686 686 0 0 0 0
in 2658.01 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS2-PH > filter region ad10013020g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10013020g200170h_0.ulc use_events=yes
Wrote events list to file ad10013020g200170h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10013020g300170h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.27E+04 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.evt
Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
Writing events file
590 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 590 0 0 0 0
in 2658.01 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS3-PH > filter region ad10013020g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10013020g300170h_0.ulc use_events=yes
Wrote events list to file ad10013020g300170h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10013020s000102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 356 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.evt
Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
Writing events file
356 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
356 356 0 0 0 0
in 1515.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10013020s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad10013020s000102h_0.ulc use_events=yes
Wrote events list to file ad10013020s000102h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10013020s000112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.15E+04 373 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s000112h.evt
Total Good Bad: Region Time Phase Cut
373 373 0 0 0 0
Writing events file
373 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 373 0 0 0 0
in 1515.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad10013020s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad10013020s000112h_0.ulc use_events=yes
Wrote events list to file ad10013020s000112h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad10013020s100102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.15E+04 346 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.evt
Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
Writing events file
346 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
346 346 0 0 0 0
in 1479.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS1-BRIGHT > filter region ad10013020s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10013020s100102h_0.ulc use_events=yes
Wrote events list to file ad10013020s100102h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10013020s100112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.15E+04 361 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020s100112h.evt
Total Good Bad: Region Time Phase Cut
361 361 0 0 0 0
Writing events file
361 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
361 361 0 0 0 0
in 1479.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad10013020s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad10013020s100112h_0.ulc use_events=yes
Wrote events list to file ad10013020s100112h_0.ulc
Changing Data directory from:
/data/data19/seq_proc/10013020.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 1894 Total of 0 sets of frame data are extracted.
1 ad10013020g200170h.unf 8291-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8291 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.unf
Total Good Bad: Region Time Phase Cut
8291 1683 6608 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8291 1683 6608 0 0 0
in 3573.99 seconds
Spectrum has 1683 counts for 0.4709 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3574.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10013020g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10013020g220170.cal group=yes
Wrote spectrum to ad10013020g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 23:37:42 11-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad10013020g220170.cal
Net count rate (cts/s) for file 1 0.4709 +/- 1.1695E-02
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 5.7844E+04 using 84 PHA bins.
Reduced chi-squared = 751.2
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 5.7338E+04 using 84 PHA bins.
Reduced chi-squared = 735.1
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 5.7338E+04 using 84 PHA bins.
Reduced chi-squared = 725.8
!XSPEC> renorm
Chi-Squared = 541.6 using 84 PHA bins.
Reduced chi-squared = 6.856
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
426.71 0 1.000 5.892 0.1269 0.1126
9.5982E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
196.90 0 1.000 5.857 0.1704 0.1820
8.4240E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
107.34 -1 1.000 5.915 0.1791 0.2647
5.1542E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
103.51 -2 1.000 5.928 0.1804 0.2837
4.1790E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
103.33 -3 1.000 5.922 0.1742 0.2811
4.4455E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
103.32 -4 1.000 5.924 0.1754 0.2820
4.3513E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
103.31 -5 1.000 5.924 0.1749 0.2818
4.3802E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92356 +/- 0.13741E-01
3 3 2 gaussian/b Sigma 0.174884 +/- 0.15933E-01
4 4 2 gaussian/b norm 0.281751 +/- 0.11028E-01
5 2 3 gaussian/b LineE 6.52187 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.183503 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.380240E-02 +/- 0.72275E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 103.3 using 84 PHA bins.
Reduced chi-squared = 1.308
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad10013020g220170.cal peaks at 5.92356 +/- 0.013741 keV1 ad10013020g300170h.unf 8018-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8018 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.unf
Total Good Bad: Region Time Phase Cut
8018 1629 6389 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8018 1629 6389 0 0 0
in 3571.99 seconds
Spectrum has 1629 counts for 0.4560 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3572.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10013020g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!xsel:ASCA > read events ad10013020g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10013020g320170.cal group=yes
Wrote spectrum to ad10013020g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 23:39:39 11-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad10013020g320170.cal
Net count rate (cts/s) for file 1 0.4560 +/- 1.1533E-02
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 5.5883E+04 using 84 PHA bins.
Reduced chi-squared = 725.8
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 5.5479E+04 using 84 PHA bins.
Reduced chi-squared = 711.3
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 5.5479E+04 using 84 PHA bins.
Reduced chi-squared = 702.3
!XSPEC> renorm
Chi-Squared = 544.4 using 84 PHA bins.
Reduced chi-squared = 6.891
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
431.39 0 1.000 5.893 0.1202 0.1160
9.8519E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
223.01 0 1.000 5.877 0.1515 0.1857
8.3985E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
104.45 -1 1.000 5.962 0.1486 0.2791
4.3432E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
97.111 -2 1.000 5.939 0.1197 0.2846
4.8731E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
96.575 -3 1.000 5.946 0.1239 0.2892
4.4384E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
96.498 -4 1.000 5.944 0.1208 0.2879
4.5610E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
96.498 -2 1.000 5.945 0.1216 0.2883
4.5189E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94461 +/- 0.10284E-01
3 3 2 gaussian/b Sigma 0.121568 +/- 0.15179E-01
4 4 2 gaussian/b norm 0.288342 +/- 0.10102E-01
5 2 3 gaussian/b LineE 6.54504 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.127560 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.518912E-02 +/- 0.56166E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 96.50 using 84 PHA bins.
Reduced chi-squared = 1.221
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad10013020g320170.cal peaks at 5.94461 +/- 0.010284 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.27E+04 8396 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10013020s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.27E+04 9144 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad10013020s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT HIGH 19/04/93 21:02:54 0.27E+04 10316 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10013020s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 VEGA BRIGHT2 HIGH 19/04/93 21:02:54 0.27E+04 11060 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad10013020s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8291 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10013020g200170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8291 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g200170h.unf
Total Good Bad: Region Time Phase Cut
8291 2838 0 5453 0 0
Writing events file
2838 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8291 2838 0 5453 0 0
in 841.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10013020g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8018 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10013020g300170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 VEGA PH HIGH 19/04/93 21:03:12 0.36E+04 8018 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/10013020.008/ad10013020g300170h.unf
Total Good Bad: Region Time Phase Cut
8018 2820 0 5198 0 0
Writing events file
2820 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8018 2820 0 5198 0 0
in 841.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/10013020.008/
Setting mkf directory to /data/data19/seq_proc/10013020.008/
!earthevents:ASCA > read events ad10013020g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/10013020.008/
HK Directory is: /data/data19/seq_proc/10013020.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files