The following information is also available:
Time column is TIME ORDERED-> Fetching fa960925_1335.1715.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 117812131.928400 117827077.879300
Data file start and stop ascatime : 117812131.928400 117827077.879300
Aspecting run start and stop ascatime : 117812131.928515 117827077.879232
Time interval averaged over (seconds) : 14945.950717
Total pointing and manuver time (sec) : 8448.374023 6497.579590
Mean boresight Euler angles : 96.903001 68.466813 339.345627
RA DEC SUN ANGLE
Mean solar position (deg) : 181.71 -0.74
Mean aberration (arcsec) : -1.72 0.70
Mean sat X-axis (deg) : 51.139204 -60.507061 107.99
Mean sat Y-axis (deg) : 179.025624 -19.154164 18.60
Mean sat Z-axis (deg) : 96.903001 21.533187 85.44
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 97.206306 21.568111 249.232986 5.593473
Minimum 95.699104 20.594757 247.812958 0.385910
Maximum 97.269104 21.625286 249.261414 102.617363
Sigma (RMS) 0.016604 0.013165 0.026989 4.602406
Number of ASPECT records processed = 3074
Aspecting to RA/DEC : 97.20630646 21.56811142
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 117820143.90196 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 117824867.88623 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 97.206 DEC: 21.568
START TIME: SC 117812131.9285 = UT 25/09/96 13:35:31
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
8.000113 18.646 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
1819.994019 18.503 F888C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 0 7
2219.992676 15.798 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2267.992432 12.231 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2315.992432 8.399 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2363.992188 5.261 EC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 5
2411.992188 2.794 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2475.991699 0.564 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2571.991699 1.683 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2667.990967 2.726 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2915.990234 3.741 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
3975.986816 4.181 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
7579.974609 4.495 DC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 3
9677.069336 2.841 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
9809.967773 2.868 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
11224.962891 102.617 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
11632.461914 3.281 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
12735.958008 4.903 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
14945.951172 18.322 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
Attitude Records: 3074
Attitude Steps: 19
Maneuver ACM time: 6497.59 sec
Pointed ACM time: 8448.39 sec
-> Calculating aspect point97 97 count=221 sum1=21359.7 sum2=15174.7 sum3=75000.5 98 97 count=12 sum1=1159.86 sum2=823.999 sum3=4072.39 98 98 count=37 sum1=3576.4 sum2=2540.84 sum3=12556.5 99 98 count=3 sum1=289.995 sum2=206.034 sum3=1018.08 99 99 count=16 sum1=1546.71 sum2=1098.93 sum3=5429.73 99 100 count=2 sum1=193.348 sum2=137.377 sum3=678.708 100 94 count=1 sum1=96.682 sum2=68.631 sum3=339.372 100 100 count=6 sum1=580.061 sum2=412.151 sum3=2036.12 100 101 count=2 sum1=193.367 sum2=137.401 sum3=678.704 101 101 count=1 sum1=96.688 sum2=68.707 sum3=339.353 105 90 count=1 sum1=96.73 sum2=68.591 sum3=339.372 110 86 count=1 sum1=96.783 sum2=68.551 sum3=339.367 115 82 count=1 sum1=96.826 sum2=68.517 sum3=339.362 118 80 count=1 sum1=96.86 sum2=68.491 sum3=339.358 119 79 count=1 sum1=96.869 sum2=68.484 sum3=339.356 121 77 count=1 sum1=96.893 sum2=68.467 sum3=339.355 122 76 count=1 sum1=96.904 sum2=68.458 sum3=339.353 122 77 count=1 sum1=96.899 sum2=68.462 sum3=339.352 123 76 count=2 sum1=193.823 sum2=136.905 sum3=678.703 124 75 count=2 sum1=193.839 sum2=136.893 sum3=678.699 125 74 count=1 sum1=96.933 sum2=68.437 sum3=339.348 125 75 count=3 sum1=290.783 sum2=205.323 sum3=1018.05 126 73 count=8 sum1=775.556 sum2=547.421 sum3=2714.75 126 74 count=13 sum1=1260.22 sum2=889.628 sum3=4411.49 127 73 count=78 sum1=7562.2 sum2=5337.08 sum3=26468.9 128 72 count=4 sum1=387.856 sum2=273.668 sum3=1357.37 128 73 count=2646 sum1=256554 sum2=181042 sum3=897900 129 72 count=1 sum1=96.966 sum2=68.41 sum3=339.354 129 73 count=4 sum1=387.86 sum2=273.674 sum3=1357.37 143 54 count=1 sum1=97.113 sum2=68.232 sum3=339.28 1 out of 3073 points outside bin structure-> Euler angles: 96.9591, 68.421, 339.343
Interpolating 1 records in time interval 1.17812e+08 - 1.17812e+08 Interpolating 1 records in time interval 1.17812e+08 - 1.17812e+08 Interpolating 1 records in time interval 1.17812e+08 - 1.17812e+08 Interpolating 4 records in time interval 1.17814e+08 - 1.17814e+08 Interpolating 5 records in time interval 1.17814e+08 - 1.17814e+08 Interpolating 5 records in time interval 1.17814e+08 - 1.17814e+08 Interpolating 4 records in time interval 1.17814e+08 - 1.17814e+08 Interpolating 3 records in time interval 1.17814e+08 - 1.17815e+08 Interpolating 2 records in time interval 1.17815e+08 - 1.17815e+08 Interpolating 1 records in time interval 1.1782e+08 - 1.17822e+08 Interpolating 2 records in time interval 1.17823e+08 - 1.17823e+08 Interpolating 245 records in time interval 1.17823e+08 - 1.17823e+08 Interpolating 245 records in time interval 1.17823e+08 - 1.17824e+08 Interpolating 2 records in time interval 1.17824e+08 - 1.17825e+08 Interpolating 21 records in time interval 1.17825e+08 - 1.17827e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft960925_1335.1715",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft960925_1335.1715 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 2 (ACS) Initial sis = 1 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 30688 Bright = 18654 Fast = 0 Frame = 2 Dark frame = 0 Histogram = 0 Integration = 0 PH = 49344 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 772 no. of SIS events found = 135615-> Standard Error Output From FTOOL frfread
coordinate error 0 0 coordinate error 490 171 coordinate error 361 451 coordinate error 0 0 coordinate error 12 0 coordinate error 0 0 coordinate error 0 0 coordinate error 286 465-> Removing the following files with NEVENTS=0
ft960925_1335_1715G200199.fits ft960925_1335_1715G300199.fits ft960925_1335_1715S000199.fits ft960925_1335_1715S000802H.fits ft960925_1335_1715S001304L.fits ft960925_1335_1715S100199.fits ft960925_1335_1715S100501M.fits-> Checking for empty GTI extensions
ft960925_1335_1715S000202M.fits[3] ft960925_1335_1715S000302L.fits[3] ft960925_1335_1715S000402L.fits[3] ft960925_1335_1715S000502M.fits[3] ft960925_1335_1715S000601M.fits[3] ft960925_1335_1715S000701H.fits[3] ft960925_1335_1715S000902M.fits[3] ft960925_1335_1715S001002M.fits[3] ft960925_1335_1715S001102L.fits[3] ft960925_1335_1715S001202L.fits[3] ft960925_1335_1715S001402L.fits[3]-> Merging GTIs from the following files:
ft960925_1335_1715S100202M.fits[3] ft960925_1335_1715S100302L.fits[3] ft960925_1335_1715S100402M.fits[3] ft960925_1335_1715S100601H.fits[3] ft960925_1335_1715S100702M.fits[3] ft960925_1335_1715S100802L.fits[3]-> Merging GTIs from the following files:
ft960925_1335_1715G200270M.fits[3] ft960925_1335_1715G200370L.fits[3] ft960925_1335_1715G200470L.fits[3] ft960925_1335_1715G200570M.fits[3] ft960925_1335_1715G200670H.fits[3] ft960925_1335_1715G200770M.fits[3] ft960925_1335_1715G200870L.fits[3] ft960925_1335_1715G200970L.fits[3]-> Merging GTIs from the following files:
ft960925_1335_1715G300270M.fits[3] ft960925_1335_1715G300370L.fits[3] ft960925_1335_1715G300470L.fits[3] ft960925_1335_1715G300570M.fits[3] ft960925_1335_1715G300670H.fits[3] ft960925_1335_1715G300770M.fits[3] ft960925_1335_1715G300870L.fits[3] ft960925_1335_1715G300970L.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 911 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 1557 GISSORTSPLIT:LO:g200270l.prelist merge count = 2 photon cnt = 193 GISSORTSPLIT:LO:g200170m.prelist merge count = 3 photon cnt = 2560 GISSORTSPLIT:LO:Total filenames split = 8 GISSORTSPLIT:LO:Total split file cnt = 4 GISSORTSPLIT:LO:End program-> Creating ad10411000g200170m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G200270M.fits 2 -- ft960925_1335_1715G200570M.fits 3 -- ft960925_1335_1715G200770M.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G200270M.fits 2 -- ft960925_1335_1715G200570M.fits 3 -- ft960925_1335_1715G200770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000g200270l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G200470L.fits 2 -- ft960925_1335_1715G200970L.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G200470L.fits 2 -- ft960925_1335_1715G200970L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960925_1335_1715G200670H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G200670H.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G200670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000193 events
ft960925_1335_1715G200370L.fits ft960925_1335_1715G200870L.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 829 GISSORTSPLIT:LO:g300170l.prelist merge count = 2 photon cnt = 1419 GISSORTSPLIT:LO:g300270l.prelist merge count = 2 photon cnt = 175 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 2399 GISSORTSPLIT:LO:Total filenames split = 8 GISSORTSPLIT:LO:Total split file cnt = 4 GISSORTSPLIT:LO:End program-> Creating ad10411000g300170m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G300270M.fits 2 -- ft960925_1335_1715G300570M.fits 3 -- ft960925_1335_1715G300770M.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G300270M.fits 2 -- ft960925_1335_1715G300570M.fits 3 -- ft960925_1335_1715G300770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000g300270l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G300470L.fits 2 -- ft960925_1335_1715G300970L.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G300470L.fits 2 -- ft960925_1335_1715G300970L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960925_1335_1715G300670H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715G300670H.fits Merging binary extension #: 2 1 -- ft960925_1335_1715G300670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000175 events
ft960925_1335_1715G300370L.fits ft960925_1335_1715G300870L.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 10475 SIS0SORTSPLIT:LO:s000201m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:s000302l.prelist merge count = 3 photon cnt = 13144 SIS0SORTSPLIT:LO:s000402l.prelist merge count = 2 photon cnt = 1323 SIS0SORTSPLIT:LO:s000502m.prelist merge count = 2 photon cnt = 17371 SIS0SORTSPLIT:LO:s000602m.prelist merge count = 2 photon cnt = 5747 SIS0SORTSPLIT:LO:Total filenames split = 11 SIS0SORTSPLIT:LO:Total split file cnt = 6 SIS0SORTSPLIT:LO:End program-> Creating ad10411000s000102m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S000502M.fits 2 -- ft960925_1335_1715S000902M.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S000502M.fits 2 -- ft960925_1335_1715S000902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000s000202l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S000402L.fits 2 -- ft960925_1335_1715S001202L.fits 3 -- ft960925_1335_1715S001402L.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S000402L.fits 2 -- ft960925_1335_1715S001202L.fits 3 -- ft960925_1335_1715S001402L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960925_1335_1715S000701H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S000701H.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S000701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000s000402m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S000202M.fits 2 -- ft960925_1335_1715S001002M.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S000202M.fits 2 -- ft960925_1335_1715S001002M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000s000502l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S000302L.fits 2 -- ft960925_1335_1715S001102L.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S000302L.fits 2 -- ft960925_1335_1715S001102L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000032 events
ft960925_1335_1715S000601M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 19971 SIS1SORTSPLIT:LO:s100202l.prelist merge count = 2 photon cnt = 18459 SIS1SORTSPLIT:LO:s100302m.prelist merge count = 3 photon cnt = 49085 SIS1SORTSPLIT:LO:Total filenames split = 6 SIS1SORTSPLIT:LO:Total split file cnt = 3 SIS1SORTSPLIT:LO:End program-> Creating ad10411000s100102m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S100202M.fits 2 -- ft960925_1335_1715S100402M.fits 3 -- ft960925_1335_1715S100702M.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S100202M.fits 2 -- ft960925_1335_1715S100402M.fits 3 -- ft960925_1335_1715S100702M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960925_1335_1715S100601H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S100601H.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S100601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad10411000s100302l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960925_1335_1715S100302L.fits 2 -- ft960925_1335_1715S100802L.fits Merging binary extension #: 2 1 -- ft960925_1335_1715S100302L.fits 2 -- ft960925_1335_1715S100802L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Tar-ing together the leftover raw files
a ft960925_1335_1715G200370L.fits 43K a ft960925_1335_1715G200870L.fits 40K a ft960925_1335_1715G300370L.fits 40K a ft960925_1335_1715G300870L.fits 40K a ft960925_1335_1715S000601M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft960925_1335.1715 'ft960925_1335.1715' is successfully opened Data Start Time is 117812128.93 (960925 133528) Time Margin 2.0 sec included Sync error detected in 772 th SF Sync error detected in 773 th SF Sync error detected in 774 th SF Sync error detected in 775 th SF Sync error detected in 776 th SF 'ft960925_1335.1715' EOF detected, sf=1743 Data End Time is 117825188.89 (960925 171308) Gain History is written in ft960925_1335_1715.ghf-> Checking if column CAL_START in ft960925_1335_1715.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft960925_1335_1715.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad10411000g200270l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000g200370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000g300270l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000g300370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000102m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000202l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000302h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000312h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s000502l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s100102m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s100201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s100202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s100212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad10411000s100302l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 96/ 9/25 13:35 mjd=50351.565972 Orbit file name is ./frf.orbit.214 Epoch of Orbital Elements: 1996/9/23 6:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa960925_1335.1715 S0-HK file: ft960925_1335_1715S0HK.fits S1-HK file: ft960925_1335_1715S1HK.fits G2-HK file: ft960925_1335_1715G2HK.fits G3-HK file: ft960925_1335_1715G3HK.fits output FITS File: ft960925_1335_1715.mkf Total 252 Data bins were processed.-> Checking if column TIME in ft960925_1335_1715.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.24E+04 17371 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
16033 14616 0 1417 0 0
Writing events file
14616 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16033 14616 0 1417 0 0
in 2179.48 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 14616
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 45 8154
Flickering pixels iter, pixels & cnts : 1 15 231
cleaning chip # 2
Hot pixels & counts : 36 5875
Flickering pixels iter, pixels & cnts : 1 10 111
cleaning chip # 3
Number of pixels rejected : 106
Number of (internal) image counts : 14616
Number of image cts rejected (N, %) : 14371 98.3237534
By chip : 0 1 2 3
Pixels rejected : 0 60 46 0
Image counts : 0 8470 6146 0
Image cts rejected: 0 8385 5986 0
Image cts rej (%) : 0.00 99.00 97.40 0.00
filtering data...
Total counts : 0 8470 6146 0
Total cts rejected: 0 8385 5986 0
Total cts rej (%) : 0.00 99.00 97.40 0.00
Number of clean counts accepted : 245
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 106
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000102m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10411000s000102m.evt use_events=no
Wrote cleaned events file to ad10411000s000102m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad10411000s000202l.unf into ad10411000s000202l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 14:01:26 0.19E+04 13144 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000202l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000202l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10411000s000202l.evt use_events=no
Wrote cleaned events file to ad10411000s000202l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000202l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.95E+03 6945 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
6355 5918 0 437 0 0
Writing events file
5918 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6355 5918 0 437 0 0
in 881.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 5918
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 40 3163
Flickering pixels iter, pixels & cnts : 1 15 164
cleaning chip # 2
Hot pixels & counts : 30 2286
Flickering pixels iter, pixels & cnts : 1 13 110
cleaning chip # 3
Number of pixels rejected : 98
Number of (internal) image counts : 5918
Number of image cts rejected (N, %) : 5723 96.7049713
By chip : 0 1 2 3
Pixels rejected : 0 55 43 0
Image counts : 0 3373 2545 0
Image cts rejected: 0 3327 2396 0
Image cts rej (%) : 0.00 98.64 94.15 0.00
filtering data...
Total counts : 0 3373 2545 0
Total cts rejected: 0 3327 2396 0
Total cts rej (%) : 0.00 98.64 94.15 0.00
Number of clean counts accepted : 195
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 98
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10411000s000302h.evt use_events=no
Wrote cleaned events file to ad10411000s000302h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad10411000s000312h.unf into ad10411000s000312h.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.95E+03 6992 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000312h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
6396 5956 0 440 0 0
Writing events file
5956 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6396 5956 0 440 0 0
in 881.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 5956
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 40 3175
Flickering pixels iter, pixels & cnts : 1 15 164
cleaning chip # 2
Hot pixels & counts : 30 2294
Flickering pixels iter, pixels & cnts : 1 13 112
cleaning chip # 3
Number of pixels rejected : 98
Number of (internal) image counts : 5956
Number of image cts rejected (N, %) : 5745 96.4573517
By chip : 0 1 2 3
Pixels rejected : 0 55 43 0
Image counts : 0 3393 2563 0
Image cts rejected: 0 3339 2406 0
Image cts rej (%) : 0.00 98.41 93.87 0.00
filtering data...
Total counts : 0 3393 2563 0
Total cts rejected: 0 3339 2406 0
Total cts rej (%) : 0.00 98.41 93.87 0.00
Number of clean counts accepted : 211
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 98
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad10411000s000312h.evt use_events=no
Wrote cleaned events file to ad10411000s000312h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad10411000s000402m.unf into ad10411000s000402m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.89E+03 5747 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
4219 533 0 3686 0 0
Writing events file
533 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4219 533 0 3686 0 0
in 76.02 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 533
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 27 239
Flickering pixels iter, pixels & cnts : 1 13 55
cleaning chip # 2
Hot pixels & counts : 21 176
Flickering pixels iter, pixels & cnts : 1 5 18
cleaning chip # 3
Number of pixels rejected : 66
Number of (internal) image counts : 533
Number of image cts rejected (N, %) : 488 91.5572205
By chip : 0 1 2 3
Pixels rejected : 0 40 26 0
Image counts : 0 321 212 0
Image cts rejected: 0 294 194 0
Image cts rej (%) : 0.00 91.59 91.51 0.00
filtering data...
Total counts : 0 321 212 0
Total cts rejected: 0 294 194 0
Total cts rej (%) : 0.00 91.59 91.51 0.00
Number of clean counts accepted : 45
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 66
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10411000s000402m.evt use_events=no
Wrote cleaned events file to ad10411000s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad10411000s000502l.unf into ad10411000s000502l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 13:50:46 0.13E+04 1323 0110
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s000502l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad10411000s000502l.evt use_events=no
Wrote cleaned events file to ad10411000s000502l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000502l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.33E+04 49085 1001
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
43640 30801 0 12839 0 0
Writing events file
30801 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
43640 30801 0 12839 0 0
in 2259.75 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 30801
Total counts in chip images : 30800
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 15705
Flickering pixels iter, pixels & cnts : 1 25 618
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 65 13695
Flickering pixels iter, pixels & cnts : 1 28 523
Number of pixels rejected : 192
Number of (internal) image counts : 30800
Number of image cts rejected (N, %) : 30541 99.1590881
By chip : 0 1 2 3
Pixels rejected : 99 0 0 93
Image counts : 16423 0 0 14377
Image cts rejected: 16323 0 0 14218
Image cts rej (%) : 99.39 0.00 0.00 98.89
filtering data...
Total counts : 16424 0 0 14377
Total cts rejected: 16324 0 0 14218
Total cts rej (%) : 99.39 0.00 0.00 98.89
Number of clean counts accepted : 259
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 192
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s100102m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10411000s100102m.evt use_events=no
Wrote cleaned events file to ad10411000s100102m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad10411000s100201h.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.95E+03 15577 1001
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13672 12723 0 949 0 0
Writing events file
12723 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13672 12723 0 949 0 0
in 887.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12723
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 73 6509
Flickering pixels iter, pixels & cnts : 1 26 326
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 62 5388
Flickering pixels iter, pixels & cnts : 1 29 344
Number of pixels rejected : 190
Number of (internal) image counts : 12723
Number of image cts rejected (N, %) : 12567 98.7738724
By chip : 0 1 2 3
Pixels rejected : 99 0 0 91
Image counts : 6886 0 0 5837
Image cts rejected: 6835 0 0 5732
Image cts rej (%) : 99.26 0.00 0.00 98.20
filtering data...
Total counts : 6886 0 0 5837
Total cts rejected: 6835 0 0 5732
Total cts rej (%) : 99.26 0.00 0.00 98.20
Number of clean counts accepted : 156
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 190
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10411000s100202h.evt use_events=no
Wrote cleaned events file to ad10411000s100202h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad10411000s100212h.unf into ad10411000s100212h.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.95E+03 15646 1001
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s100212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13890 12926 0 964 0 0
Writing events file
12926 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13890 12926 0 964 0 0
in 887.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12926
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 6595
Flickering pixels iter, pixels & cnts : 1 25 313
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 63 5502
Flickering pixels iter, pixels & cnts : 1 28 336
Number of pixels rejected : 190
Number of (internal) image counts : 12926
Number of image cts rejected (N, %) : 12746 98.6074600
By chip : 0 1 2 3
Pixels rejected : 99 0 0 91
Image counts : 6964 0 0 5962
Image cts rejected: 6908 0 0 5838
Image cts rej (%) : 99.20 0.00 0.00 97.92
filtering data...
Total counts : 6964 0 0 5962
Total cts rejected: 6908 0 0 5838
Total cts rej (%) : 99.20 0.00 0.00 97.92
Number of clean counts accepted : 180
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 190
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad10411000s100212h.evt use_events=no
Wrote cleaned events file to ad10411000s100212h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad10411000s100302l.unf into ad10411000s100302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 13:50:46 0.32E+04 18459 1001
Processing file: /data/data22/seq_proc/10411000.009/ad10411000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data22/seq_proc/10411000.009/screen_in_event.xsl
reading data file: /data/data22/seq_proc/10411000.009/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad10411000s100302l.evt use_events=no
Wrote cleaned events file to ad10411000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10411000s100302l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.unf
Total Good Bad: Region Time Phase Cut
2560 761 1630 169 0 0
Writing events file
761 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2560 761 1630 169 0 0
in 2688.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
761 661 100
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10411000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 661 in ad10411000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1557 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g200270l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10411000g200270l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10411000g200270l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 911 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.unf
Total Good Bad: Region Time Phase Cut
911 317 582 12 0 0
Writing events file
317 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
911 317 582 12 0 0
in 928.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
317 267 50
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad10411000g200370h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 267 in ad10411000g200370h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.unf
Total Good Bad: Region Time Phase Cut
2399 823 1382 194 0 0
Writing events file
823 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2399 823 1382 194 0 0
in 2688.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
823 701 122
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10411000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 701 in ad10411000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1419 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g300270l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10411000g300270l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10411000g300270l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 829 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.unf
Total Good Bad: Region Time Phase Cut
829 324 491 14 0 0
Writing events file
324 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
829 324 491 14 0 0
in 928.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
324 255 69
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!screen:ASCA > read events ad10411000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad10411000g300370h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 255 in ad10411000g300370h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad10411000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2269
Mean RA/DEC/ROLL : 97.2795 21.6224 249.2269
Pnt RA/DEC/ROLL : 96.9698 21.3894 249.2269
Image rebin factor : 1
Attitude Records : 3617
GTI intervals : 2
Total GTI (secs) : 2688.003
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 336.9893188 336.9893188
20 Percent Complete: Total/live time: 800.9877930 800.9877930
30 Percent Complete: Total/live time: 1924.9841309 1924.9841309
40 Percent Complete: Total/live time: 1924.9841309 1924.9841309
50 Percent Complete: Total/live time: 2688.0034180 2688.0034180
100 Percent Complete: Total/live time: 2688.0034180 2688.0034180
Number of attitude steps used: 11
Number of attitude steps avail: 857
Mean RA/DEC pixel offset: -9.0905 -2.6802
writing expo file: ad10411000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 653 8 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
661 653 8 0 0 0
in 2688.00 seconds
Image has 653 counts for 0.2429 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 273 8 0 0 380
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
661 273 8 0 0 380
in 2688.00 seconds
Image has 273 counts for 0.1016 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 383 8 0 0 270
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
661 383 8 0 0 270
in 2688.00 seconds
Image has 383 counts for 0.1425 counts/sec
Command not found; type ? for a command listing
!ad10411000g200170m:ASCA >
!ad10411000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000g200170m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000g200170m:ASCA > read events ad10411000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000g200170m:ASCA-GIS2-PH > set image sky
!ad10411000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad10411000g200170m:ASCA-GIS2-PH > extract image
!ad10411000g200170m:ASCA-GIS2-PH > save image outfile=ad10411000g200170m.img
Wrote image to file ad10411000g200170m.img
!ad10411000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10411000g200170m:ASCA-GIS2-PH > extract image
!ad10411000g200170m:ASCA-GIS2-PH > save image outfile=ad10411000g200170m_lo.img
Wrote image to file ad10411000g200170m_lo.img
!ad10411000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad10411000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10411000g200170m:ASCA-GIS2-PH > extract image
!ad10411000g200170m:ASCA-GIS2-PH > save image outfile=ad10411000g200170m_hi.img
Wrote image to file ad10411000g200170m_hi.img
!ad10411000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10411000g200370h.expo
ASCAEXPO_V0.9b
reading data file: ad10411000g200370h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2251
Mean RA/DEC/ROLL : 97.2469 21.5966 249.2251
Pnt RA/DEC/ROLL : 97.2752 21.6307 249.2251
Image rebin factor : 1
Attitude Records : 3617
GTI intervals : 2
Total GTI (secs) : 927.997
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 236.4992523 236.4992523
20 Percent Complete: Total/live time: 236.4992523 236.4992523
30 Percent Complete: Total/live time: 535.9979858 535.9979858
40 Percent Complete: Total/live time: 535.9979858 535.9979858
50 Percent Complete: Total/live time: 706.9974365 706.9974365
60 Percent Complete: Total/live time: 706.9974365 706.9974365
70 Percent Complete: Total/live time: 711.4974976 711.4974976
80 Percent Complete: Total/live time: 904.9967041 904.9967041
90 Percent Complete: Total/live time: 904.9967041 904.9967041
100 Percent Complete: Total/live time: 927.9967651 927.9967651
Number of attitude steps used: 7
Number of attitude steps avail: 1932
Mean RA/DEC pixel offset: -9.1944 -3.2942
writing expo file: ad10411000g200370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000g200370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000g200370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 267 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 261 6 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
267 261 6 0 0 0
in 928.00 seconds
Image has 261 counts for 0.2813 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 134 6 0 0 127
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
267 134 6 0 0 127
in 928.00 seconds
Image has 134 counts for 0.1444 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 127 6 0 0 134
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
267 127 6 0 0 134
in 928.00 seconds
Image has 127 counts for 0.1369 counts/sec
Command not found; type ? for a command listing
!ad10411000g200370h:ASCA >
!ad10411000g200370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000g200370h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000g200370h:ASCA > read events ad10411000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000g200370h:ASCA-GIS2-PH > set image sky
!ad10411000g200370h:ASCA-GIS2-PH > filter region corner_point.reg
!ad10411000g200370h:ASCA-GIS2-PH > extract image
!ad10411000g200370h:ASCA-GIS2-PH > save image outfile=ad10411000g200370h.img
Wrote image to file ad10411000g200370h.img
!ad10411000g200370h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad10411000g200370h:ASCA-GIS2-PH > extract image
!ad10411000g200370h:ASCA-GIS2-PH > save image outfile=ad10411000g200370h_lo.img
Wrote image to file ad10411000g200370h_lo.img
!ad10411000g200370h:ASCA-GIS2-PH > clear pha_cut
!ad10411000g200370h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10411000g200370h:ASCA-GIS2-PH > extract image
!ad10411000g200370h:ASCA-GIS2-PH > save image outfile=ad10411000g200370h_hi.img
Wrote image to file ad10411000g200370h_hi.img
!ad10411000g200370h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad10411000g300170m.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad10411000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2313
Mean RA/DEC/ROLL : 97.2930 21.6459 249.2313
Pnt RA/DEC/ROLL : 96.9580 21.3672 249.2313
Image rebin factor : 1
Attitude Records : 3617
GTI intervals : 2
Total GTI (secs) : 2688.003
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 336.9893188 336.9893188
20 Percent Complete: Total/live time: 800.9877930 800.9877930
30 Percent Complete: Total/live time: 1924.9841309 1924.9841309
40 Percent Complete: Total/live time: 1924.9841309 1924.9841309
50 Percent Complete: Total/live time: 2688.0034180 2688.0034180
100 Percent Complete: Total/live time: 2688.0034180 2688.0034180
Number of attitude steps used: 11
Number of attitude steps avail: 857
Mean RA/DEC pixel offset: 1.8901 -1.5894
writing expo file: ad10411000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 692 9 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
701 692 9 0 0 0
in 2688.00 seconds
Image has 692 counts for 0.2574 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 302 9 0 0 390
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
701 302 9 0 0 390
in 2688.00 seconds
Image has 302 counts for 0.1124 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 392 9 0 0 300
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
701 392 9 0 0 300
in 2688.00 seconds
Image has 392 counts for 0.1458 counts/sec
Command not found; type ? for a command listing
!ad10411000g300170m:ASCA >
!ad10411000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000g300170m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000g300170m:ASCA > read events ad10411000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000g300170m:ASCA-GIS3-PH > set image sky
!ad10411000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad10411000g300170m:ASCA-GIS3-PH > extract image
!ad10411000g300170m:ASCA-GIS3-PH > save image outfile=ad10411000g300170m.img
Wrote image to file ad10411000g300170m.img
!ad10411000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10411000g300170m:ASCA-GIS3-PH > extract image
!ad10411000g300170m:ASCA-GIS3-PH > save image outfile=ad10411000g300170m_lo.img
Wrote image to file ad10411000g300170m_lo.img
!ad10411000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad10411000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10411000g300170m:ASCA-GIS3-PH > extract image
!ad10411000g300170m:ASCA-GIS3-PH > save image outfile=ad10411000g300170m_hi.img
Wrote image to file ad10411000g300170m_hi.img
!ad10411000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10411000g300370h.expo
ASCAEXPO_V0.9b
reading data file: ad10411000g300370h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2296
Mean RA/DEC/ROLL : 97.2587 21.6188 249.2296
Pnt RA/DEC/ROLL : 97.2633 21.6085 249.2296
Image rebin factor : 1
Attitude Records : 3617
GTI intervals : 2
Total GTI (secs) : 927.997
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 236.4992523 236.4992523
20 Percent Complete: Total/live time: 236.4992523 236.4992523
30 Percent Complete: Total/live time: 535.9979858 535.9979858
40 Percent Complete: Total/live time: 535.9979858 535.9979858
50 Percent Complete: Total/live time: 706.9974365 706.9974365
60 Percent Complete: Total/live time: 706.9974365 706.9974365
70 Percent Complete: Total/live time: 711.4974976 711.4974976
80 Percent Complete: Total/live time: 904.9967041 904.9967041
90 Percent Complete: Total/live time: 904.9967041 904.9967041
100 Percent Complete: Total/live time: 927.9967651 927.9967651
Number of attitude steps used: 7
Number of attitude steps avail: 1932
Mean RA/DEC pixel offset: 1.1587 -2.2657
writing expo file: ad10411000g300370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000g300370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000g300370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 250 5 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
255 250 5 0 0 0
in 928.00 seconds
Image has 250 counts for 0.2694 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 111 5 0 0 139
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
255 111 5 0 0 139
in 928.00 seconds
Image has 111 counts for 0.1196 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 139 5 0 0 111
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
255 139 5 0 0 111
in 928.00 seconds
Image has 139 counts for 0.1498 counts/sec
Command not found; type ? for a command listing
!ad10411000g300370h:ASCA >
!ad10411000g300370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000g300370h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000g300370h:ASCA > read events ad10411000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000g300370h:ASCA-GIS3-PH > set image sky
!ad10411000g300370h:ASCA-GIS3-PH > filter region corner_point.reg
!ad10411000g300370h:ASCA-GIS3-PH > extract image
!ad10411000g300370h:ASCA-GIS3-PH > save image outfile=ad10411000g300370h.img
Wrote image to file ad10411000g300370h.img
!ad10411000g300370h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad10411000g300370h:ASCA-GIS3-PH > extract image
!ad10411000g300370h:ASCA-GIS3-PH > save image outfile=ad10411000g300370h_lo.img
Wrote image to file ad10411000g300370h_lo.img
!ad10411000g300370h:ASCA-GIS3-PH > clear pha_cut
!ad10411000g300370h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad10411000g300370h:ASCA-GIS3-PH > extract image
!ad10411000g300370h:ASCA-GIS3-PH > save image outfile=ad10411000g300370h_hi.img
Wrote image to file ad10411000g300370h_hi.img
!ad10411000g300370h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad10411000s000102m.expo
ASCAEXPO_V0.9b
reading data file: ad10411000s000102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2216
Mean RA/DEC/ROLL : 97.2360 21.6122 249.2216
Pnt RA/DEC/ROLL : 97.2733 21.6087 249.2216
Image rebin factor : 4
Attitude Records : 3617
Hot Pixels : 106
GTI intervals : 2
Total GTI (secs) : 2179.483
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 293.7391357 293.7391357
20 Percent Complete: Total/live time: 626.7381592 626.7381592
30 Percent Complete: Total/live time: 1566.7348633 1566.7348633
40 Percent Complete: Total/live time: 1566.7348633 1566.7348633
50 Percent Complete: Total/live time: 2179.4829102 2179.4829102
100 Percent Complete: Total/live time: 2179.4829102 2179.4829102
Number of attitude steps used: 8
Number of attitude steps avail: 794
Mean RA/DEC pixel offset: -36.5059 -83.8232
writing expo file: ad10411000s000102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000s000102m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000s000102m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.22E+04 245 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.evt
Total Good Bad: Region Time Phase Cut
245 245 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
245 245 0 0 0 0
in 2179.48 seconds
Image has 245 counts for 0.1124 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.evt
Total Good Bad: Region Time Phase Cut
245 158 0 0 0 87
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
245 158 0 0 0 87
in 2179.48 seconds
Image has 158 counts for 7.2494E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.evt
Total Good Bad: Region Time Phase Cut
245 87 0 0 0 158
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
245 87 0 0 0 158
in 2179.48 seconds
Image has 87 counts for 3.9918E-02 counts/sec
Command not found; type ? for a command listing
!ad10411000s000102m:ASCA >
!ad10411000s000102m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000s000102m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000s000102m:ASCA > read events ad10411000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000s000102m:ASCA-SIS0-BRIGHT > set image sky
!ad10411000s000102m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad10411000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000102m.img
Wrote image to file ad10411000s000102m.img
!ad10411000s000102m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad10411000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000102m_lo.img
Wrote image to file ad10411000s000102m_lo.img
!ad10411000s000102m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad10411000s000102m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10411000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000102m_hi.img
Wrote image to file ad10411000s000102m_hi.img
!ad10411000s000102m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad10411000s000302h.expo
ASCAEXPO_V0.9b
reading data file: ad10411000s000302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2217
Mean RA/DEC/ROLL : 97.2375 21.6132 249.2217
Pnt RA/DEC/ROLL : 97.2845 21.6140 249.2217
Image rebin factor : 4
Attitude Records : 3617
Hot Pixels : 98
GTI intervals : 2
Total GTI (secs) : 881.966
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 112.9994965 112.9994965
20 Percent Complete: Total/live time: 522.4982300 522.4982300
30 Percent Complete: Total/live time: 522.4982300 522.4982300
40 Percent Complete: Total/live time: 682.9974976 682.9974976
50 Percent Complete: Total/live time: 682.9974976 682.9974976
60 Percent Complete: Total/live time: 687.4975586 687.4975586
70 Percent Complete: Total/live time: 687.4975586 687.4975586
80 Percent Complete: Total/live time: 880.9967651 880.9967651
90 Percent Complete: Total/live time: 880.9967651 880.9967651
100 Percent Complete: Total/live time: 881.9656372 881.9656372
Number of attitude steps used: 7
Number of attitude steps avail: 1935
Mean RA/DEC pixel offset: -36.5255 -84.9702
writing expo file: ad10411000s000302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000s000302h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000s000302h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.88E+03 195 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.evt
Total Good Bad: Region Time Phase Cut
195 195 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
195 195 0 0 0 0
in 881.97 seconds
Image has 195 counts for 0.2211 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.evt
Total Good Bad: Region Time Phase Cut
195 162 0 0 0 33
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
195 162 0 0 0 33
in 881.97 seconds
Image has 162 counts for 0.1837 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.evt
Total Good Bad: Region Time Phase Cut
195 33 0 0 0 162
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
195 33 0 0 0 162
in 881.97 seconds
Image has 33 counts for 3.7416E-02 counts/sec
Command not found; type ? for a command listing
!ad10411000s000302h:ASCA >
!ad10411000s000302h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000s000302h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000s000302h:ASCA > read events ad10411000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000s000302h:ASCA-SIS0-BRIGHT > set image sky
!ad10411000s000302h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad10411000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000302h.img
Wrote image to file ad10411000s000302h.img
!ad10411000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad10411000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000302h_lo.img
Wrote image to file ad10411000s000302h_lo.img
!ad10411000s000302h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad10411000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10411000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000302h_hi.img
Wrote image to file ad10411000s000302h_hi.img
!ad10411000s000302h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad10411000s000402m.expo
ASCAEXPO_V0.9b
reading data file: ad10411000s000402m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2235
Mean RA/DEC/ROLL : 97.3427 21.6965 249.2235
Pnt RA/DEC/ROLL : 96.9793 21.3729 249.2235
Image rebin factor : 4
Attitude Records : 3617
Hot Pixels : 66
GTI intervals : 1
Total GTI (secs) : 76.020
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 76.0204773 76.0204773
100 Percent Complete: Total/live time: 76.0204773 76.0204773
Number of attitude steps used: 2
Number of attitude steps avail: 40
Mean RA/DEC pixel offset: -28.3750 -54.8398
writing expo file: ad10411000s000402m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000s000402m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000s000402m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.76E+02 45 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.evt
Total Good Bad: Region Time Phase Cut
45 45 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
45 45 0 0 0 0
in 76.02 seconds
Image has 45 counts for 0.5919 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.evt
Total Good Bad: Region Time Phase Cut
45 40 0 0 0 5
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
45 40 0 0 0 5
in 76.02 seconds
Image has 40 counts for 0.5262 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.evt
Total Good Bad: Region Time Phase Cut
45 5 0 0 0 40
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
45 5 0 0 0 40
in 76.02 seconds
Image has 5 counts for 6.5772E-02 counts/sec
Command not found; type ? for a command listing
!ad10411000s000402m:ASCA >
!ad10411000s000402m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000s000402m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000s000402m:ASCA > read events ad10411000s000402m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000s000402m:ASCA-SIS0-BRIGHT > set image sky
!ad10411000s000402m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad10411000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000402m.img
Wrote image to file ad10411000s000402m.img
!ad10411000s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad10411000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000402m_lo.img
Wrote image to file ad10411000s000402m_lo.img
!ad10411000s000402m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad10411000s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10411000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad10411000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad10411000s000402m_hi.img
Wrote image to file ad10411000s000402m_hi.img
!ad10411000s000402m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad10411000s100102m.expo
ASCAEXPO_V0.9b
reading data file: ad10411000s100102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2292
Mean RA/DEC/ROLL : 97.2840 21.6311 249.2292
Pnt RA/DEC/ROLL : 96.9637 21.3794 249.2292
Image rebin factor : 4
Attitude Records : 3617
Hot Pixels : 192
GTI intervals : 2
Total GTI (secs) : 2259.753
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 299.7391357 299.7391357
20 Percent Complete: Total/live time: 724.7375488 724.7375488
30 Percent Complete: Total/live time: 724.7375488 724.7375488
40 Percent Complete: Total/live time: 2012.7333984 2012.7333984
50 Percent Complete: Total/live time: 2012.7333984 2012.7333984
60 Percent Complete: Total/live time: 2259.7531738 2259.7531738
100 Percent Complete: Total/live time: 2259.7531738 2259.7531738
Number of attitude steps used: 8
Number of attitude steps avail: 804
Mean RA/DEC pixel offset: -40.8660 -21.0420
writing expo file: ad10411000s100102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000s100102m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000s100102m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.23E+04 259 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.evt
Total Good Bad: Region Time Phase Cut
259 259 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
259 259 0 0 0 0
in 2259.75 seconds
Image has 259 counts for 0.1146 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.evt
Total Good Bad: Region Time Phase Cut
259 151 0 0 0 108
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
259 151 0 0 0 108
in 2259.75 seconds
Image has 151 counts for 6.6821E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.evt
Total Good Bad: Region Time Phase Cut
259 108 0 0 0 151
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
259 108 0 0 0 151
in 2259.75 seconds
Image has 108 counts for 4.7793E-02 counts/sec
Command not found; type ? for a command listing
!ad10411000s100102m:ASCA >
!ad10411000s100102m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000s100102m:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000s100102m:ASCA > read events ad10411000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000s100102m:ASCA-SIS1-BRIGHT > set image sky
!ad10411000s100102m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad10411000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100102m.img
Wrote image to file ad10411000s100102m.img
!ad10411000s100102m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad10411000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100102m_lo.img
Wrote image to file ad10411000s100102m_lo.img
!ad10411000s100102m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad10411000s100102m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10411000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100102m_hi.img
Wrote image to file ad10411000s100102m_hi.img
!ad10411000s100102m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad10411000s100202h.expo
ASCAEXPO_V0.9b
reading data file: ad10411000s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960925_1335.1715
making an exposure map...
Aspect RA/DEC/ROLL : 97.2625 21.6139 249.2274
Mean RA/DEC/ROLL : 97.2531 21.6067 249.2274
Pnt RA/DEC/ROLL : 97.2689 21.6206 249.2274
Image rebin factor : 4
Attitude Records : 3617
Hot Pixels : 190
GTI intervals : 2
Total GTI (secs) : 887.966
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 112.9995041 112.9995041
20 Percent Complete: Total/live time: 522.4982300 522.4982300
30 Percent Complete: Total/live time: 522.4982300 522.4982300
40 Percent Complete: Total/live time: 682.9974976 682.9974976
50 Percent Complete: Total/live time: 682.9974976 682.9974976
60 Percent Complete: Total/live time: 687.4975586 687.4975586
70 Percent Complete: Total/live time: 687.4975586 687.4975586
80 Percent Complete: Total/live time: 880.9967651 880.9967651
90 Percent Complete: Total/live time: 880.9967651 880.9967651
100 Percent Complete: Total/live time: 887.9655762 887.9655762
Number of attitude steps used: 7
Number of attitude steps avail: 1935
Mean RA/DEC pixel offset: -40.3349 -23.3835
writing expo file: ad10411000s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad10411000s100202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad10411000s100202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.89E+03 156 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.evt
Total Good Bad: Region Time Phase Cut
156 156 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
156 156 0 0 0 0
in 887.97 seconds
Image has 156 counts for 0.1757 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.evt
Total Good Bad: Region Time Phase Cut
156 105 0 0 0 51
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
156 105 0 0 0 51
in 887.97 seconds
Image has 105 counts for 0.1182 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.evt
Total Good Bad: Region Time Phase Cut
156 51 0 0 0 105
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
156 51 0 0 0 105
in 887.97 seconds
Image has 51 counts for 5.7435E-02 counts/sec
Command not found; type ? for a command listing
!ad10411000s100202h:ASCA >
!ad10411000s100202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad10411000s100202h:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!ad10411000s100202h:ASCA > read events ad10411000s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!ad10411000s100202h:ASCA-SIS1-BRIGHT > set image sky
!ad10411000s100202h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad10411000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100202h.img
Wrote image to file ad10411000s100202h.img
!ad10411000s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad10411000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100202h_lo.img
Wrote image to file ad10411000s100202h_lo.img
!ad10411000s100202h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad10411000s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad10411000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad10411000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad10411000s100202h_hi.img
Wrote image to file ad10411000s100202h_hi.img
!ad10411000s100202h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad10411000s000102m.expo ad10411000s000302h.expo ad10411000s000402m.expo ad10411000s100102m.expo ad10411000s100202h.expo-> Summing the following images to produce ad10411000sis32002_all.totsky
ad10411000s000102m.img ad10411000s000302h.img ad10411000s000402m.img ad10411000s100102m.img ad10411000s100202h.img-> Summing the following images to produce ad10411000sis32002_lo.totsky
ad10411000s000102m_lo.img ad10411000s000302h_lo.img ad10411000s000402m_lo.img ad10411000s100102m_lo.img ad10411000s100202h_lo.img-> Summing the following images to produce ad10411000sis32002_hi.totsky
ad10411000s000102m_hi.img ad10411000s000302h_hi.img ad10411000s000402m_hi.img ad10411000s100102m_hi.img ad10411000s100202h_hi.img-> Running XIMAGE to create ad10411000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad10411000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 6.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 6 min: 0 ![2]XIMAGE> read/exp_map ad10411000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 104.7531 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 104 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 8379 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 21.0000 21 0 ![9]XIMAGE> exit-> Summing gis images
ad10411000g200170m.expo ad10411000g200370h.expo ad10411000g300170m.expo ad10411000g300370h.expo-> Summing the following images to produce ad10411000gis25670_all.totsky
ad10411000g200170m.img ad10411000g200370h.img ad10411000g300170m.img ad10411000g300370h.img-> Summing the following images to produce ad10411000gis25670_lo.totsky
ad10411000g200170m_lo.img ad10411000g200370h_lo.img ad10411000g300170m_lo.img ad10411000g300370h_lo.img-> Summing the following images to produce ad10411000gis25670_hi.totsky
ad10411000g200170m_hi.img ad10411000g200370h_hi.img ad10411000g300170m_hi.img ad10411000g300370h_hi.img-> Running XIMAGE to create ad10411000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad10411000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 3.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 3 min: 0 ![2]XIMAGE> read/exp_map ad10411000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 120.533 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 120 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 7301 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 42.0000 42 0 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad10411000gis25670.src
126 250 1.43598e-05 221 28 4.77741-> Determining extraction radii
126 250 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad10411000sis32002.src
The sum of the selected column is 19028.000 The mean of the selected column is 1001.4737 The standard deviation of the selected column is 16.925879 The minimum of selected column is 964.00000 The maximum of selected column is 1029.0000 The number of points used in calculation is 19-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 11225.000 The mean of the selected column is 590.78947 The standard deviation of the selected column is 20.378581 The minimum of selected column is 554.00000 The maximum of selected column is 624.00000 The number of points used in calculation is 19-> Converting (504.0,1000.0,2.0) to s1 detector coordinates
The sum of the selected column is 2018.0000 The mean of the selected column is 1009.0000 The standard deviation of the selected column is 38.183766 The minimum of selected column is 982.00000 The maximum of selected column is 1036.0000 The number of points used in calculation is 2-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1221.0000 The mean of the selected column is 610.50000 The standard deviation of the selected column is 19.091883 The minimum of selected column is 597.00000 The maximum of selected column is 624.00000 The number of points used in calculation is 2
1 ad10411000s000102m.evt 440 1 ad10411000s000302h.evt 440 2 ad10411000s000402m.evt 45-> Standard Output From STOOL group_event_files:
1 ad10411000s000312h.evt 211-> Standard Output From STOOL group_event_files:
1 ad10411000s100102m.evt 415 1 ad10411000s100202h.evt 415-> Standard Output From STOOL group_event_files:
1 ad10411000s100212h.evt 180-> Standard Output From STOOL group_event_files:
1 ad10411000g200170m.evt 928 1 ad10411000g200370h.evt 928-> GIS2_REGION256.4 already present in current directory
ad10411000g200170m.evt ad10411000g200370h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
2 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 267 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 661 0 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 267 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
928 928 0 0 0 0
in 3616.00 seconds
Spectrum has 928 counts for 0.2566 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3616.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36888 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10411000g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > read events ad10411000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad10411000g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10411000g210170_0.pi group=yes
Wrote spectrum to ad10411000g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad10411000g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad10411000g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3616.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 28 are grouped by a factor 29 ... 29 - 42 are grouped by a factor 14 ... 43 - 65 are grouped by a factor 23 ... 66 - 81 are grouped by a factor 16 ... 82 - 111 are grouped by a factor 15 ... 112 - 124 are grouped by a factor 13 ... 125 - 140 are grouped by a factor 16 ... 141 - 170 are grouped by a factor 15 ... 171 - 193 are grouped by a factor 23 ... 194 - 222 are grouped by a factor 29 ... 223 - 248 are grouped by a factor 26 ... 249 - 282 are grouped by a factor 34 ... 283 - 319 are grouped by a factor 37 ... 320 - 371 are grouped by a factor 52 ... 372 - 417 are grouped by a factor 46 ... 418 - 469 are grouped by a factor 52 ... 470 - 540 are grouped by a factor 71 ... 541 - 629 are grouped by a factor 89 ... 630 - 741 are grouped by a factor 112 ... 742 - 910 are grouped by a factor 169 ... 911 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad10411000g210170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.28000E+02
Weighted mean angle from optical axis = 14.423 arcmin
-> Standard Output From STOOL group_event_files:1 ad10411000g300170m.evt 956 1 ad10411000g300370h.evt 956-> GIS3_REGION256.4 already present in current directory
ad10411000g300170m.evt ad10411000g300370h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
2 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 701 0 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 255 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
956 956 0 0 0 0
in 3616.00 seconds
Spectrum has 956 counts for 0.2644 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3616.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36783 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10411000g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > read events ad10411000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad10411000g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10411000g310170_0.pi group=yes
Wrote spectrum to ad10411000g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad10411000g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad10411000g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3616.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 28 are grouped by a factor 29 ... 29 - 46 are grouped by a factor 18 ... 47 - 74 are grouped by a factor 28 ... 75 - 91 are grouped by a factor 17 ... 92 - 115 are grouped by a factor 12 ... 116 - 128 are grouped by a factor 13 ... 129 - 140 are grouped by a factor 12 ... 141 - 155 are grouped by a factor 15 ... 156 - 172 are grouped by a factor 17 ... 173 - 190 are grouped by a factor 18 ... 191 - 223 are grouped by a factor 33 ... 224 - 247 are grouped by a factor 24 ... 248 - 283 are grouped by a factor 36 ... 284 - 321 are grouped by a factor 38 ... 322 - 358 are grouped by a factor 37 ... 359 - 398 are grouped by a factor 40 ... 399 - 444 are grouped by a factor 46 ... 445 - 526 are grouped by a factor 82 ... 527 - 603 are grouped by a factor 77 ... 604 - 691 are grouped by a factor 88 ... 692 - 812 are grouped by a factor 121 ... 813 - 969 are grouped by a factor 157 ... 970 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad10411000g310170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.56000E+02
Weighted mean angle from optical axis = 14.005 arcmin
-> Plotting ad10411000g210170_0_pi.ps from ad10411000g210170_0.pi
XSPEC 9.01 17:01:25 21-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad10411000g210170_0.pi
Net count rate (cts/s) for file 1 0.2566 +/- 8.8496E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad10411000g310170_0_pi.ps from ad10411000g310170_0.pi
XSPEC 9.01 17:01:40 21-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad10411000g310170_0.pi
Net count rate (cts/s) for file 1 0.2644 +/- 8.7583E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.22E+04 245 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.22E+04 245 0110
2 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.88E+03 195 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.22E+04 245 0110
2 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.88E+03 195 0110
3 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.76E+02 45 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.evt
Total Good Bad: Region Time Phase Cut
245 41 204 0 0 0
Writing events file
41 events written to the output file
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.evt
Total Good Bad: Region Time Phase Cut
195 56 139 0 0 0
Writing events file
97 events written to the output file
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.evt
Total Good Bad: Region Time Phase Cut
45 2 43 0 0 0
Writing events file
99 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
485 99 386 0 0 0
in 3137.47 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > read events ad10411000s000302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > read events ad10411000s000402m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10411000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> skipping ad10411000s000002_1.lc since it would have 99 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.23E+04 259 1001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.23E+04 259 1001
2 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.89E+03 156 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.evt
Total Good Bad: Region Time Phase Cut
259 18 241 0 0 0
Writing events file
18 events written to the output file
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.evt
Total Good Bad: Region Time Phase Cut
156 4 152 0 0 0
Writing events file
22 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
415 22 393 0 0 0
in 3147.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS1-BRIGHT > read events ad10411000s100202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS1-BRIGHT > filter region ad10411000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> skipping ad10411000s100002_1.lc since it would have 22 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
2 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 267 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 661 0 0 0 0
Writing events file
661 events written to the output file
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 267 0 0 0 0
Writing events file
928 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
928 928 0 0 0 0
in 3616.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > read events ad10411000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > filter region ad10411000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad10411000g200070_0.lc with binsize 194.827586206897
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.36E+04 928 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/events.tmp
Total Good Bad: Region Time Phase Cut
928 928 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
928 928 0 0 0 0
in 3616.00 seconds
Fits light curve has 928 counts for 0.2566 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > set binsize 194.827586206897
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad10411000g200070_0.lc
Wrote FITS light curve to file ad10411000g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad10411000g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad10411000g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ COMET_TABUR_N1 Start Time (d) .... 10351 14:23:30.928
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10351 15:24:18.928
No. of Rows ....... 19 Bin Time (s) ...... 194.8
Right Ascension ... 9.7262E+01 Internal time sys.. Converted to TJD
Declination ....... 2.1614E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 19 Newbins of 194.828 (s)
Intv 1 Start10351 14:25: 8
Ser.1 Avg 0.2563 Chisq 27.08 Var 0.1928E-02 Newbs. 19
Min 0.1694 Max 0.3644 expVar 0.1353E-02 Bins 19
Results from Statistical Analysis
Newbin Integration Time (s).. 194.83
Interval Duration (s)........ 3506.9
No. of Newbins .............. 19
Average (c/s) ............... 0.25627 +/- 0.87E-02
Standard Deviation (c/s)..... 0.43909E-01
Minimum (c/s)................ 0.16938
Maximum (c/s)................ 0.36442
Variance ((c/s)**2).......... 0.19280E-02 +/- 0.64E-03
Expected Variance ((c/s)**2). 0.13526E-02 +/- 0.45E-03
Third Moment ((c/s)**3)...... 0.34212E-04
Average Deviation (c/s)...... 0.35959E-01
Skewness..................... 0.40413 +/- 0.56
Kurtosis..................... 0.14163 +/- 1.1
RMS fractional variation....< 0.13418 (3 sigma)
Chi-Square................... 27.082 dof 18
Chi-Square Prob of constancy. 0.77486E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.12848E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 19 Newbins of 194.828 (s)
Intv 1 Start10351 14:25: 8
Ser.1 Avg 0.2563 Chisq 27.08 Var 0.1928E-02 Newbs. 19
Min 0.1694 Max 0.3644 expVar 0.1353E-02 Bins 19
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad10411000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
2 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 701 0 0 0 0
Writing events file
701 events written to the output file
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 255 0 0 0 0
Writing events file
956 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
956 956 0 0 0 0
in 3616.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > read events ad10411000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > filter region ad10411000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad10411000g300070_0.lc with binsize 189.121338912134
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.36E+04 956 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/events.tmp
Total Good Bad: Region Time Phase Cut
956 956 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
956 956 0 0 0 0
in 3616.00 seconds
Fits light curve has 956 counts for 0.2644 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > set binsize 189.121338912134
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad10411000g300070_0.lc
Wrote FITS light curve to file ad10411000g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad10411000g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad10411000g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ COMET_TABUR_N1 Start Time (d) .... 10351 14:23:30.928
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10351 15:24:18.928
No. of Rows ....... 19 Bin Time (s) ...... 189.1
Right Ascension ... 9.7262E+01 Internal time sys.. Converted to TJD
Declination ....... 2.1614E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 20 Newbins of 189.121 (s)
Intv 1 Start10351 14:25: 5
Ser.1 Avg 0.2658 Chisq 21.77 Var 0.1629E-02 Newbs. 19
Min 0.1956 Max 0.3437 expVar 0.1422E-02 Bins 19
Results from Statistical Analysis
Newbin Integration Time (s).. 189.12
Interval Duration (s)........ 3404.2
No. of Newbins .............. 19
Average (c/s) ............... 0.26582 +/- 0.89E-02
Standard Deviation (c/s)..... 0.40359E-01
Minimum (c/s)................ 0.19564
Maximum (c/s)................ 0.34369
Variance ((c/s)**2).......... 0.16289E-02 +/- 0.54E-03
Expected Variance ((c/s)**2). 0.14218E-02 +/- 0.47E-03
Third Moment ((c/s)**3)...... 0.88089E-05
Average Deviation (c/s)...... 0.34201E-01
Skewness..................... 0.13399 +/- 0.56
Kurtosis.....................-0.94696 +/- 1.1
RMS fractional variation....< 0.15237 (3 sigma)
Chi-Square................... 21.768 dof 18
Chi-Square Prob of constancy. 0.24250 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.44851 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 20 Newbins of 189.121 (s)
Intv 1 Start10351 14:25: 5
Ser.1 Avg 0.2658 Chisq 21.77 Var 0.1629E-02 Newbs. 19
Min 0.1956 Max 0.3437 expVar 0.1422E-02 Bins 19
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad10411000g200170m.evt[2] ad10411000g200370h.evt[2]-> Making L1 light curve of ft960925_1335_1715G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2458 output records from 2460 good input G2_L1 records.-> Making L1 light curve of ft960925_1335_1715G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3288 output records from 4854 good input G2_L1 records.-> Merging GTIs from the following files:
ad10411000g300170m.evt[2] ad10411000g300370h.evt[2]-> Making L1 light curve of ft960925_1335_1715G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2191 output records from 2193 good input G3_L1 records.-> Making L1 light curve of ft960925_1335_1715G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3253 output records from 4576 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 661 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.evt
Total Good Bad: Region Time Phase Cut
661 661 0 0 0 0
Writing events file
661 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
661 661 0 0 0 0
in 2688.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > filter region ad10411000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10411000g200170m_0.ulc use_events=yes
Wrote events list to file ad10411000g200170m_0.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10411000g200370h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 267 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.evt
Total Good Bad: Region Time Phase Cut
267 267 0 0 0 0
Writing events file
267 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
267 267 0 0 0 0
in 928.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > filter region ad10411000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad10411000g200370h_0.ulc use_events=yes
Wrote events list to file ad10411000g200370h_0.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad10411000g300170m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.27E+04 701 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.evt
Total Good Bad: Region Time Phase Cut
701 701 0 0 0 0
Writing events file
701 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
701 701 0 0 0 0
in 2688.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > filter region ad10411000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10411000g300170m_0.ulc use_events=yes
Wrote events list to file ad10411000g300170m_0.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10411000g300370h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.93E+03 255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.evt
Total Good Bad: Region Time Phase Cut
255 255 0 0 0 0
Writing events file
255 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
255 255 0 0 0 0
in 928.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > filter region ad10411000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad10411000g300370h_0.ulc use_events=yes
Wrote events list to file ad10411000g300370h_0.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad10411000s000102m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.22E+04 245 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.evt
Total Good Bad: Region Time Phase Cut
245 41 204 0 0 0
Writing events file
41 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
245 41 204 0 0 0
in 2179.48 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10411000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad10411000s000102m_1.ulc use_events=yes
Wrote events list to file ad10411000s000102m_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10411000s000302h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.88E+03 195 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.evt
Total Good Bad: Region Time Phase Cut
195 56 139 0 0 0
Writing events file
56 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
195 56 139 0 0 0
in 881.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10411000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad10411000s000302h_1.ulc use_events=yes
Wrote events list to file ad10411000s000302h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10411000s000312h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.88E+03 211 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000312h.evt
Total Good Bad: Region Time Phase Cut
211 59 152 0 0 0
Writing events file
59 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
211 59 152 0 0 0
in 881.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s000312h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad10411000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad10411000s000312h_1.ulc use_events=yes
Wrote events list to file ad10411000s000312h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad10411000s000402m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.76E+02 45 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.evt
Total Good Bad: Region Time Phase Cut
45 2 43 0 0 0
Writing events file
2 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
45 2 43 0 0 0
in 76.02 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s000402m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS0-BRIGHT > filter region ad10411000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad10411000s000402m_1.ulc use_events=yes
Wrote events list to file ad10411000s000402m_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000402m_1.ulc since it has 2 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.23E+04 259 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.evt
Total Good Bad: Region Time Phase Cut
259 18 241 0 0 0
Writing events file
18 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
259 18 241 0 0 0
in 2259.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS1-BRIGHT > filter region ad10411000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10411000s100102m_1.ulc use_events=yes
Wrote events list to file ad10411000s100102m_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad10411000s100202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.89E+03 156 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.evt
Total Good Bad: Region Time Phase Cut
156 4 152 0 0 0
Writing events file
4 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
156 4 152 0 0 0
in 887.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS1-BRIGHT > filter region ad10411000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad10411000s100202h_1.ulc use_events=yes
Wrote events list to file ad10411000s100202h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10411000s100202h_1.ulc since it has 4 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.89E+03 180 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100212h.evt
Total Good Bad: Region Time Phase Cut
180 4 176 0 0 0
Writing events file
4 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
180 4 176 0 0 0
in 887.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000s100212h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad10411000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad10411000s100212h_1.ulc use_events=yes
Wrote events list to file ad10411000s100212h_1.ulc
Changing Data directory from:
/data/data22/seq_proc/10411000.009/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad10411000s100212h_1.ulc since it has 4 events*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 1743 Total of 0 sets of frame data are extracted.
1 ad10411000g200170m.unf 5028 1 ad10411000g200270l.unf 5028 1 ad10411000g200370h.unf 5028-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
2 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1557 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
2 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1557 1024
3 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 911 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.unf
Total Good Bad: Region Time Phase Cut
2560 585 1975 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200270l.unf
Total Good Bad: Region Time Phase Cut
1557 520 1037 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.unf
Total Good Bad: Region Time Phase Cut
911 182 729 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5028 1287 3741 0 0 0
in 7199.98 seconds
Spectrum has 1287 counts for 0.1788 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7200.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10411000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > read events ad10411000g200270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > read events ad10411000g200370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad10411000g220170.cal group=yes
Wrote spectrum to ad10411000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 17:12:44 21-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad10411000g220170.cal
Net count rate (cts/s) for file 1 0.1788 +/- 5.1670E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.4040E+05 using 84 PHA bins.
Reduced chi-squared = 3122.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.3945E+05 using 84 PHA bins.
Reduced chi-squared = 3070.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.3945E+05 using 84 PHA bins.
Reduced chi-squared = 3031.
!XSPEC> renorm
Chi-Squared = 359.3 using 84 PHA bins.
Reduced chi-squared = 4.548
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
297.57 0 1.000 5.896 8.6867E-02 5.7240E-02
5.0900E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
148.57 0 1.000 5.881 0.1319 8.2031E-02
4.3745E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
80.670 -1 1.000 5.927 0.1442 0.1132
2.9403E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
77.400 -2 1.000 5.941 0.1435 0.1206
2.5042E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
77.289 -3 1.000 5.937 0.1385 0.1198
2.5915E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
77.282 -4 1.000 5.939 0.1394 0.1200
2.5658E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93860 +/- 0.13052E-01
3 3 2 gaussian/b Sigma 0.139373 +/- 0.16447E-01
4 4 2 gaussian/b norm 0.120025 +/- 0.49539E-02
5 2 3 gaussian/b LineE 6.53842 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.146243 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.565772E-02 +/- 0.32920E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 77.28 using 84 PHA bins.
Reduced chi-squared = 0.9783
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad10411000g220170.cal peaks at 5.93860 +/- 0.013052 keV1 ad10411000g300170m.unf 4647 1 ad10411000g300270l.unf 4647 1 ad10411000g300370h.unf 4647-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
2 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1419 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
2 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1419 1024
3 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 829 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.unf
Total Good Bad: Region Time Phase Cut
2399 513 1886 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300270l.unf
Total Good Bad: Region Time Phase Cut
1419 423 996 0 0 0
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.unf
Total Good Bad: Region Time Phase Cut
829 162 667 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4647 1098 3549 0 0 0
in 7199.98 seconds
Spectrum has 1098 counts for 0.1525 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7200.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad10411000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!xsel:ASCA > read events ad10411000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > read events ad10411000g300270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > read events ad10411000g300370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad10411000g320170.cal group=yes
Wrote spectrum to ad10411000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 17:13:25 21-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad10411000g320170.cal
Net count rate (cts/s) for file 1 0.1525 +/- 4.8591E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 3.1851E+05 using 84 PHA bins.
Reduced chi-squared = 4136.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 3.1638E+05 using 84 PHA bins.
Reduced chi-squared = 4056.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 3.1638E+05 using 84 PHA bins.
Reduced chi-squared = 4005.
!XSPEC> renorm
Chi-Squared = 404.9 using 84 PHA bins.
Reduced chi-squared = 5.126
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
341.66 0 1.000 5.894 6.1210E-02 4.6137E-02
3.9218E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
152.91 0 1.000 5.876 8.7265E-02 7.3937E-02
3.2555E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
66.491 -1 1.000 5.924 0.1052 0.1049
2.1303E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
59.913 -2 1.000 5.943 0.1101 0.1141
1.6822E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
59.876 -3 1.000 5.942 0.1078 0.1141
1.6870E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
59.876 -4 1.000 5.942 0.1078 0.1141
1.6868E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94190 +/- 0.11241E-01
3 3 2 gaussian/b Sigma 0.107846 +/- 0.17888E-01
4 4 2 gaussian/b norm 0.114105 +/- 0.44799E-02
5 2 3 gaussian/b LineE 6.54206 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.113162 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.686811E-02 +/- 0.24517E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 59.88 using 84 PHA bins.
Reduced chi-squared = 0.7579
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad10411000g320170.cal peaks at 5.94190 +/- 0.011241 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 14:21:42 0.24E+04 17371 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s000102m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000102m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000102m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 14:01:26 0.19E+04 13144 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000202l.unf
Total Good Bad: Region Time Phase Cut
13144 12920 0 224 0 0
Writing events file
12920 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13144 12920 0 224 0 0
in 1877.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000202l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10411000s000202l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad10411000s000202l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12920
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 45 6996
Flickering pixels iter, pixels & cnts : 1 15 167
cleaning chip # 2
Hot pixels & counts : 34 5484
Flickering pixels iter, pixels & cnts : 1 11 112
cleaning chip # 3
Number of pixels rejected : 105
Number of (internal) image counts : 12920
Number of image cts rejected (N, %) : 12759 98.7538681
By chip : 0 1 2 3
Pixels rejected : 0 60 45 0
Image counts : 0 7244 5676 0
Image cts rejected: 0 7163 5596 0
Image cts rej (%) : 0.00 98.88 98.59 0.00
filtering data...
Total counts : 0 7244 5676 0
Total cts rejected: 0 7163 5596 0
Total cts rej (%) : 0.00 98.88 98.59 0.00
Number of clean counts accepted : 161
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 105
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad10411000s000302h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.95E+03 6945 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s000302h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000302h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.95E+03 6992 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s000312h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad10411000s000312h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.89E+03 5747 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s000402m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad10411000s000402m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 13:50:46 0.13E+04 1323 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s000502l.unf
Total Good Bad: Region Time Phase Cut
1323 1096 0 227 0 0
Writing events file
1096 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1323 1096 0 227 0 0
in 193.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10411000s000502l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad10411000s000502l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1096
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 29 528
Flickering pixels iter, pixels & cnts : 1 12 54
cleaning chip # 2
Hot pixels & counts : 23 404
Flickering pixels iter, pixels & cnts : 1 7 32
cleaning chip # 3
Number of pixels rejected : 71
Number of (internal) image counts : 1096
Number of image cts rejected (N, %) : 1018 92.8832092
By chip : 0 1 2 3
Pixels rejected : 0 41 30 0
Image counts : 0 619 477 0
Image cts rejected: 0 582 436 0
Image cts rej (%) : 0.00 94.02 91.40 0.00
filtering data...
Total counts : 0 619 477 0
Total cts rejected: 0 582 436 0
Total cts rej (%) : 0.00 94.02 91.40 0.00
Number of clean counts accepted : 78
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 71
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad10411000s100102m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT MEDIUM 25/09/96 13:44:54 0.33E+04 49085 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s100102m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s100102m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10411000s100102m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT HIGH 25/09/96 14:30:18 0.95E+03 15577 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s100202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad10411000s100202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT2 HIGH 25/09/96 14:30:18 0.95E+03 15646 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000s100212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad10411000s100212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 COMET_TA BRIGHT LOW 25/09/96 13:50:46 0.32E+04 18459 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000s100302l.unf
Total Good Bad: Region Time Phase Cut
18459 16640 0 1819 0 0
Writing events file
16640 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18459 16640 0 1819 0 0
in 2080.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad10411000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad10411000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 16640
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 42 7853
Flickering pixels iter, pixels & cnts : 1 20 405
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 38 7861
Flickering pixels iter, pixels & cnts : 1 22 413
Number of pixels rejected : 122
Number of (internal) image counts : 16640
Number of image cts rejected (N, %) : 16532 99.3509598
By chip : 0 1 2 3
Pixels rejected : 62 0 0 60
Image counts : 8320 0 0 8320
Image cts rejected: 8258 0 0 8274
Image cts rej (%) : 99.25 0.00 0.00 99.45
filtering data...
Total counts : 8320 0 0 8320
Total cts rejected: 8258 0 0 8274
Total cts rej (%) : 99.25 0.00 0.00 99.45
Number of clean counts accepted : 108
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 122
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad10411000g200170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10411000g200170m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2560 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200170m.unf
Total Good Bad: Region Time Phase Cut
2560 48 0 2512 0 0
Writing events file
48 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2560 48 0 2512 0 0
in 63.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10411000g200270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1557 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200270l.unf
Total Good Bad: Region Time Phase Cut
1557 1057 0 500 0 0
Writing events file
1057 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1557 1057 0 500 0 0
in 2080.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad10411000g200270l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1557 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g200270l.unf
Total Good Bad: Region Time Phase Cut
1557 470 0 1087 0 0
Writing events file
470 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1557 470 0 1087 0 0
in 800.03 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10411000g200370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 911 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10411000g200370h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 911 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g200370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad10411000g200370h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10411000g300170m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH MEDIUM 25/09/96 13:45:06 0.33E+04 2399 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300170m.unf
Total Good Bad: Region Time Phase Cut
2399 42 0 2357 0 0
Writing events file
42 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2399 42 0 2357 0 0
in 63.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10411000g300270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1419 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300270l.unf
Total Good Bad: Region Time Phase Cut
1419 947 0 472 0 0
Writing events file
947 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1419 947 0 472 0 0
in 2080.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad10411000g300270l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH LOW 25/09/96 13:53:06 0.29E+04 1419 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data22/seq_proc/10411000.009/ad10411000g300270l.unf
Total Good Bad: Region Time Phase Cut
1419 447 0 972 0 0
Writing events file
447 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1419 447 0 972 0 0
in 800.03 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad10411000g300370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 829 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10411000g300370h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 COMET_TA PH HIGH 25/09/96 14:30:26 0.96E+03 829 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data22/seq_proc/10411000.009/ad10411000g300370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data22/seq_proc/10411000.009/
Setting mkf directory to /data/data22/seq_proc/10411000.009/
!earthevents:ASCA > read events ad10411000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data22/seq_proc/10411000.009/
HK Directory is: /data/data22/seq_proc/10411000.009/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad10411000g300370h.brt since it contains 0 eventsOffset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad10411000s000102m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad10411000s000402m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad10411000s000102m.unf
ad10411000s000202l.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad10411000s000502l.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad10411000s000202l.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files