The following information is also available:
Time column is TIME ORDERED-> Fetching fa950802_0233.2030.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 81484483.679400 81549031.977800
Data file start and stop ascatime : 81484483.679400 81549031.977800
Aspecting run start and stop ascatime : 81484483.679478 81549031.977725
Time interval averaged over (seconds) : 64548.298247
Total pointing and manuver time (sec) : 40803.476562 23744.988281
Mean boresight Euler angles : 350.611478 31.357214 53.500247
RA DEC SUN ANGLE
Mean solar position (deg) : 131.19 18.07
Mean aberration (arcsec) : 27.33 -9.17
Mean sat X-axis (deg) : 48.323653 -18.030750 89.07
Mean sat Y-axis (deg) : 129.701946 24.727686 6.80
Mean sat Z-axis (deg) : 350.611478 58.642788 96.74
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 350.695099 58.923721 323.429260 0.055594
Minimum 350.691559 58.921234 323.418457 0.000000
Maximum 350.702026 58.924915 323.450134 0.405624
Sigma (RMS) 0.000992 0.000148 0.002298 0.029320
Number of ASPECT records processed = 63712
Aspecting to RA/DEC : 350.69509888 58.92372131
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 350.695 DEC: 58.924
START TIME: SC 81484483.6795 = UT 02/08/95 02:34:43
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500095 0.095 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
495.998596 0.069 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
4015.987549 0.203 E02883 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 4
6695.979004 0.090 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
9775.969727 0.088 E02883 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 4
11949.962891 0.092 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
15535.951172 0.057 E02883 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 4
17831.943359 0.064 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
21263.933594 0.021 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
23943.925781 0.026 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
27007.916016 0.038 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
29189.908203 0.024 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
32751.898438 0.055 FC28C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
34935.890625 0.026 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
38511.878906 0.063 E02883 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 4
40687.871094 0.028 F820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
44271.863281 0.064 E02883 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 4
46431.855469 0.071 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
50031.843750 0.056 FC28C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
52175.835938 0.032 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
55743.824219 0.028 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
57923.820312 0.035 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
61487.808594 0.043 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
63669.800781 0.005 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
64548.296875 0.146 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
Attitude Records: 63712
Attitude Steps: 25
Maneuver ACM time: 23745.0 sec
Pointed ACM time: 40803.5 sec
-> Calculating aspect point98 100 count=1 sum1=350.602 sum2=31.362 sum3=53.521 99 99 count=43391 sum1=1.52133e+07 sum2=1.36062e+06 sum3=2.3215e+06 99 100 count=1673 sum1=586570 sum2=52464.4 sum3=89508 100 99 count=18422 sum1=6.45899e+06 sum2=577666 sum3=985540 100 100 count=224 sum1=78537.6 sum2=7024.42 sum3=11983.2 0 out of 63711 points outside bin structure-> Euler angles: 350.611, 31.3573, 53.5007
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft950802_0233.2030",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft950802_0233.2030 Initial mode = 4 (Frame) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 945476 Bright = 41596 Fast = 0 Frame = 32960 Dark frame = 0 Histogram = 0 Integration = 0 PH = 1020032 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 16024 no. of SIS events found = 2368053
ERROR: time_beg < time_end in update_gti time_beg = 8.14844856796088665724e+07, time_end = 8.14844876483588665724e+07 SUPERFRAME: 13 input telemetry file: ./ft950802_0233.2030 unit = 7 bit_rate = 4, old_bit_rate = 4 coordinate error 0 24 coordinate error 0 12 coordinate error 0 0 coordinate error 0 3 coordinate error 256 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 24 coordinate error 39 438 coordinate error 241 425 coordinate error 0 0 coordinate error 96 0 coordinate error 0 12 coordinate error 0 0 coordinate error 0 0 coordinate error 6 0 coordinate error 0 12 coordinate error 0 0 coordinate error 3 281-> Par file from FTOOL frfread
frf_filelist,s,h,".frffiles",,,"file containing list of input telemetry files" output_directory,s,h,"./",,,"Directory for output files" origin,s,h,"GSFC",,,"FITS ORIGIN keyword" object,s,h,"CAS_A_C1H",,,"FITS OBJECT keyword" seqpi,s,h,"NONE",,,"FITS OBSERVER keyword" ranom,s,h,"350.695",,,"FITS RA_NOM keyword" decnom,s,h,"58.9236",,,"FITS DEC_NOM keyword" start_sf,i,h,0,,,"start superframe" end_sf,i,h,0,,,"end superframe" min_grade,i,h,0,0,7,"minimum grade" max_grade,i,h,7,0,7,"maximum grade" bin_size,i,h,8,0,0,"mkfilter bin size (seconds) for output of HK parameters" split_threshold,i,h,0,,,"split threshold" combine,i,h,0,0,1,"combine faint mode pha values into one pha value" which_sis,i,h,2,0,2,"which sis to read (0,1,2; 2 = both 0 and 1)" which_ccd,i,h,4,0,4,"which ccd to read (0,1,2,3,4; 4 = all 4 ccds)" override,i,h,0,0,1,"override default input parameter file list" commonhk,i,h,1,0,1,"create common HK file?" insthk,i,h,1,0,1,"create instrument HK files?" aea,i,h,1,0,1,"change file when AE-A status (AEANLGS) changes? (SIS)" clobber,i,h,1,0,1,"clobber output files?" display_spectrum,i,h,0,0,1,"display spectrum?" display_ltcurve,i,h,0,0,1,"display light curve?" display_image,i,h,0,0,1,"display image?" display_summary,i,h,0,0,1,"display summary?" write_spectrum,i,h,0,0,1,"write spectrum to file?" write_ltcurve,i,h,0,0,1,"write light curve to file?" write_image,i,h,0,0,1,"write image to file?" write_events,i,h,1,0,1,"write events to output files?" write_diag,i,h,1,0,1,"write diagnostic mode images to output files?" read_faint,i,h,1,0,1,"process faint mode data?" read_bright,i,h,1,0,1,"process bright mode data?" read_fast,i,h,1,0,1,"process fast mode data?" read_hist,i,h,1,0,1,"process histogram mode data?" read_frame,i,h,1,0,1,"process frame mode data?" read_dark,i,h,1,0,1,"process dark mode data?" read_integ,i,h,1,0,1,"process integration mode data?" read_ph,i,h,1,0,1,"process ph mode data?" read_memcheck,i,h,1,0,1,"process memory check data?" read_mpc,i,h,1,0,1,"process mpc mode data?" read_pcal,i,h,1,0,1,"process pcal mode data?" print_spectrum,i,h,0,0,1,"print spectrum?" print_ltcurve,i,h,0,0,1,"print light curve?" print_image,i,h,0,0,1,"print image?" print_summary,i,h,0,0,1,"print summary?" debug_level,i,h,0,0,4,"debug level?"-> Removing the following files with NEVENTS=0
ft950802_0233_2030G202570M.fits ft950802_0233_2030G203070L.fits ft950802_0233_2030G204770L.fits ft950802_0233_2030G204899.fits ft950802_0233_2030G205199.fits ft950802_0233_2030G205470H.fits ft950802_0233_2030G205570H.fits ft950802_0233_2030G206170H.fits ft950802_0233_2030G206270H.fits ft950802_0233_2030G206699.fits ft950802_0233_2030G206970M.fits ft950802_0233_2030G207070H.fits ft950802_0233_2030G207170H.fits ft950802_0233_2030G302570M.fits ft950802_0233_2030G303070L.fits ft950802_0233_2030G304770L.fits ft950802_0233_2030G304899.fits ft950802_0233_2030G305199.fits ft950802_0233_2030G305670H.fits ft950802_0233_2030G305770H.fits ft950802_0233_2030G306170M.fits ft950802_0233_2030G306270M.fits ft950802_0233_2030G306370H.fits ft950802_0233_2030G306899.fits ft950802_0233_2030G307170M.fits ft950802_0233_2030G307270M.fits ft950802_0233_2030G307370H.fits ft950802_0233_2030S000004H.fits ft950802_0233_2030S000301H.fits ft950802_0233_2030S000701H.fits ft950802_0233_2030S001101M.fits ft950802_0233_2030S001601M.fits ft950802_0233_2030S003001L.fits ft950802_0233_2030S003301M.fits ft950802_0233_2030S004101M.fits ft950802_0233_2030S004699.fits ft950802_0233_2030S004999.fits ft950802_0233_2030S005301H.fits ft950802_0233_2030S005599.fits ft950802_0233_2030S005901H.fits ft950802_0233_2030S100304H.fits ft950802_0233_2030S100701H.fits ft950802_0233_2030S101101M.fits ft950802_0233_2030S101601M.fits ft950802_0233_2030S102901L.fits ft950802_0233_2030S103201M.fits ft950802_0233_2030S104001M.fits ft950802_0233_2030S104599.fits ft950802_0233_2030S104899.fits ft950802_0233_2030S105301H.fits ft950802_0233_2030S105599.fits ft950802_0233_2030S105901H.fits-> Checking for empty GTI extensions
ft950802_0233_2030S000101H.fits[3] ft950802_0233_2030S000201L.fits[3] ft950802_0233_2030S000401H.fits[3] ft950802_0233_2030S000501L.fits[3] ft950802_0233_2030S000601H.fits[3] ft950802_0233_2030S000802H.fits[3] ft950802_0233_2030S000902L.fits[3] ft950802_0233_2030S001002M.fits[3] ft950802_0233_2030S001201H.fits[3] ft950802_0233_2030S001302H.fits[3] ft950802_0233_2030S001402L.fits[3] ft950802_0233_2030S001502M.fits[3] ft950802_0233_2030S001701H.fits[3] ft950802_0233_2030S001801M.fits[3] ft950802_0233_2030S001901H.fits[3] ft950802_0233_2030S002001M.fits[3] ft950802_0233_2030S002101H.fits[3] ft950802_0233_2030S002201M.fits[3] ft950802_0233_2030S002301H.fits[3] ft950802_0233_2030S002401H.fits[3] ft950802_0233_2030S002501H.fits[3] ft950802_0233_2030S002601H.fits[3] ft950802_0233_2030S002701H.fits[3] ft950802_0233_2030S002801H.fits[3] ft950802_0233_2030S002901H.fits[3] ft950802_0233_2030S003102L.fits[3] ft950802_0233_2030S003202M.fits[3] ft950802_0233_2030S003401H.fits[3] ft950802_0233_2030S003501H.fits[3] ft950802_0233_2030S003601H.fits[3] ft950802_0233_2030S003702L.fits[3] ft950802_0233_2030S003802L.fits[3] ft950802_0233_2030S003902L.fits[3] ft950802_0233_2030S004002M.fits[3] ft950802_0233_2030S004201H.fits[3] ft950802_0233_2030S004302L.fits[3] ft950802_0233_2030S004402L.fits[3] ft950802_0233_2030S004502L.fits[3] ft950802_0233_2030S004702M.fits[3] ft950802_0233_2030S004801H.fits[3] ft950802_0233_2030S005001H.fits[3] ft950802_0233_2030S005101M.fits[3] ft950802_0233_2030S005201M.fits[3] ft950802_0233_2030S005401H.fits[3] ft950802_0233_2030S005601H.fits[3] ft950802_0233_2030S005701M.fits[3] ft950802_0233_2030S005801M.fits[3] ft950802_0233_2030S006001H.fits[3]-> Merging GTIs from the following files:
ft950802_0233_2030S100101H.fits[3] ft950802_0233_2030S100201L.fits[3] ft950802_0233_2030S100401H.fits[3] ft950802_0233_2030S100501L.fits[3] ft950802_0233_2030S100601H.fits[3] ft950802_0233_2030S100802H.fits[3] ft950802_0233_2030S100902L.fits[3] ft950802_0233_2030S101002M.fits[3] ft950802_0233_2030S101201H.fits[3] ft950802_0233_2030S101302H.fits[3] ft950802_0233_2030S101402L.fits[3] ft950802_0233_2030S101502M.fits[3] ft950802_0233_2030S101701H.fits[3] ft950802_0233_2030S101801H.fits[3] ft950802_0233_2030S101901M.fits[3] ft950802_0233_2030S102001H.fits[3] ft950802_0233_2030S102101M.fits[3] ft950802_0233_2030S102201H.fits[3] ft950802_0233_2030S102301M.fits[3] ft950802_0233_2030S102401H.fits[3] ft950802_0233_2030S102501H.fits[3] ft950802_0233_2030S102601H.fits[3] ft950802_0233_2030S102701H.fits[3] ft950802_0233_2030S102801H.fits[3] ft950802_0233_2030S103002L.fits[3] ft950802_0233_2030S103102M.fits[3] ft950802_0233_2030S103301H.fits[3] ft950802_0233_2030S103401H.fits[3] ft950802_0233_2030S103501H.fits[3] ft950802_0233_2030S103602L.fits[3] ft950802_0233_2030S103702L.fits[3] ft950802_0233_2030S103802L.fits[3] ft950802_0233_2030S103902M.fits[3] ft950802_0233_2030S104101H.fits[3] ft950802_0233_2030S104202L.fits[3] ft950802_0233_2030S104302L.fits[3] ft950802_0233_2030S104402L.fits[3] ft950802_0233_2030S104602M.fits[3] ft950802_0233_2030S104701H.fits[3] ft950802_0233_2030S104901H.fits[3] ft950802_0233_2030S105001H.fits[3] ft950802_0233_2030S105101M.fits[3] ft950802_0233_2030S105201M.fits[3] ft950802_0233_2030S105401H.fits[3] ft950802_0233_2030S105601H.fits[3] ft950802_0233_2030S105701M.fits[3] ft950802_0233_2030S105801M.fits[3] ft950802_0233_2030S106001H.fits[3]-> Merging GTIs from the following files:
ft950802_0233_2030G200170H.fits[3] ft950802_0233_2030G200270L.fits[3] ft950802_0233_2030G200370H.fits[3] ft950802_0233_2030G200470H.fits[3] ft950802_0233_2030G200570H.fits[3] ft950802_0233_2030G200670H.fits[3] ft950802_0233_2030G200770L.fits[3] ft950802_0233_2030G200870H.fits[3] ft950802_0233_2030G200970H.fits[3] ft950802_0233_2030G201070H.fits[3] ft950802_0233_2030G201170H.fits[3] ft950802_0233_2030G201270L.fits[3] ft950802_0233_2030G201370M.fits[3] ft950802_0233_2030G201470H.fits[3] ft950802_0233_2030G201570L.fits[3] ft950802_0233_2030G201670L.fits[3] ft950802_0233_2030G201770M.fits[3] ft950802_0233_2030G201870H.fits[3] ft950802_0233_2030G201970M.fits[3] ft950802_0233_2030G202070H.fits[3] ft950802_0233_2030G202170M.fits[3] ft950802_0233_2030G202270H.fits[3] ft950802_0233_2030G202370M.fits[3] ft950802_0233_2030G202470M.fits[3] ft950802_0233_2030G202670M.fits[3] ft950802_0233_2030G202770M.fits[3] ft950802_0233_2030G202870H.fits[3] ft950802_0233_2030G202970L.fits[3] ft950802_0233_2030G203170L.fits[3] ft950802_0233_2030G203270L.fits[3] ft950802_0233_2030G203370M.fits[3] ft950802_0233_2030G203470M.fits[3] ft950802_0233_2030G203570M.fits[3] ft950802_0233_2030G203670M.fits[3] ft950802_0233_2030G203770H.fits[3] ft950802_0233_2030G203870L.fits[3] ft950802_0233_2030G203970L.fits[3] ft950802_0233_2030G204070L.fits[3] ft950802_0233_2030G204170M.fits[3] ft950802_0233_2030G204270M.fits[3] ft950802_0233_2030G204370M.fits[3] ft950802_0233_2030G204470M.fits[3] ft950802_0233_2030G204570H.fits[3] ft950802_0233_2030G204670L.fits[3] ft950802_0233_2030G204970M.fits[3] ft950802_0233_2030G205070H.fits[3] ft950802_0233_2030G205270H.fits[3] ft950802_0233_2030G205370H.fits[3] ft950802_0233_2030G205670H.fits[3] ft950802_0233_2030G205770H.fits[3] ft950802_0233_2030G205870H.fits[3] ft950802_0233_2030G205970M.fits[3] ft950802_0233_2030G206070M.fits[3] ft950802_0233_2030G206370H.fits[3] ft950802_0233_2030G206470H.fits[3] ft950802_0233_2030G206570H.fits[3] ft950802_0233_2030G206770H.fits[3] ft950802_0233_2030G206870M.fits[3] ft950802_0233_2030G207270H.fits[3] ft950802_0233_2030G207370H.fits[3] ft950802_0233_2030G207470H.fits[3]-> Merging GTIs from the following files:
ft950802_0233_2030G300170H.fits[3] ft950802_0233_2030G300270L.fits[3] ft950802_0233_2030G300370H.fits[3] ft950802_0233_2030G300470H.fits[3] ft950802_0233_2030G300570H.fits[3] ft950802_0233_2030G300670H.fits[3] ft950802_0233_2030G300770L.fits[3] ft950802_0233_2030G300870H.fits[3] ft950802_0233_2030G300970H.fits[3] ft950802_0233_2030G301070H.fits[3] ft950802_0233_2030G301170H.fits[3] ft950802_0233_2030G301270L.fits[3] ft950802_0233_2030G301370M.fits[3] ft950802_0233_2030G301470H.fits[3] ft950802_0233_2030G301570L.fits[3] ft950802_0233_2030G301670L.fits[3] ft950802_0233_2030G301770M.fits[3] ft950802_0233_2030G301870H.fits[3] ft950802_0233_2030G301970M.fits[3] ft950802_0233_2030G302070H.fits[3] ft950802_0233_2030G302170M.fits[3] ft950802_0233_2030G302270H.fits[3] ft950802_0233_2030G302370M.fits[3] ft950802_0233_2030G302470M.fits[3] ft950802_0233_2030G302670M.fits[3] ft950802_0233_2030G302770M.fits[3] ft950802_0233_2030G302870H.fits[3] ft950802_0233_2030G302970L.fits[3] ft950802_0233_2030G303170L.fits[3] ft950802_0233_2030G303270L.fits[3] ft950802_0233_2030G303370M.fits[3] ft950802_0233_2030G303470M.fits[3] ft950802_0233_2030G303570M.fits[3] ft950802_0233_2030G303670M.fits[3] ft950802_0233_2030G303770H.fits[3] ft950802_0233_2030G303870L.fits[3] ft950802_0233_2030G303970L.fits[3] ft950802_0233_2030G304070L.fits[3] ft950802_0233_2030G304170M.fits[3] ft950802_0233_2030G304270M.fits[3] ft950802_0233_2030G304370M.fits[3] ft950802_0233_2030G304470M.fits[3] ft950802_0233_2030G304570H.fits[3] ft950802_0233_2030G304670L.fits[3] ft950802_0233_2030G304970M.fits[3] ft950802_0233_2030G305070H.fits[3] ft950802_0233_2030G305270H.fits[3] ft950802_0233_2030G305370H.fits[3] ft950802_0233_2030G305470H.fits[3] ft950802_0233_2030G305570H.fits[3] ft950802_0233_2030G305870H.fits[3] ft950802_0233_2030G305970H.fits[3] ft950802_0233_2030G306070M.fits[3] ft950802_0233_2030G306470H.fits[3] ft950802_0233_2030G306570H.fits[3] ft950802_0233_2030G306670H.fits[3] ft950802_0233_2030G306770H.fits[3] ft950802_0233_2030G306970H.fits[3] ft950802_0233_2030G307070M.fits[3] ft950802_0233_2030G307470H.fits[3] ft950802_0233_2030G307570H.fits[3] ft950802_0233_2030G307670H.fits[3] ft950802_0233_2030G307770H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 32 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 74 GISSORTSPLIT:LO:g200470h.prelist merge count = 16 photon cnt = 960373 GISSORTSPLIT:LO:g200570h.prelist merge count = 2 photon cnt = 146 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 60 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 70 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 66 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 80 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 306 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 52 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 34 GISSORTSPLIT:LO:g200370l.prelist merge count = 9 photon cnt = 16934 GISSORTSPLIT:LO:g200470l.prelist merge count = 1 photon cnt = 512 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270m.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200370m.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g200470m.prelist merge count = 11 photon cnt = 105939 GISSORTSPLIT:LO:g200570m.prelist merge count = 2 photon cnt = 512 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g200870m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g200970m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:Total filenames split = 61 GISSORTSPLIT:LO:Total split file cnt = 24 GISSORTSPLIT:LO:End program-> Creating ad12002220g200170h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G200170H.fits 2 -- ft950802_0233_2030G200670H.fits 3 -- ft950802_0233_2030G201170H.fits 4 -- ft950802_0233_2030G201470H.fits 5 -- ft950802_0233_2030G201870H.fits 6 -- ft950802_0233_2030G202070H.fits 7 -- ft950802_0233_2030G202270H.fits 8 -- ft950802_0233_2030G202870H.fits 9 -- ft950802_0233_2030G203770H.fits 10 -- ft950802_0233_2030G204570H.fits 11 -- ft950802_0233_2030G205070H.fits 12 -- ft950802_0233_2030G205270H.fits 13 -- ft950802_0233_2030G205870H.fits 14 -- ft950802_0233_2030G206570H.fits 15 -- ft950802_0233_2030G206770H.fits 16 -- ft950802_0233_2030G207470H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G200170H.fits 2 -- ft950802_0233_2030G200670H.fits 3 -- ft950802_0233_2030G201170H.fits 4 -- ft950802_0233_2030G201470H.fits 5 -- ft950802_0233_2030G201870H.fits 6 -- ft950802_0233_2030G202070H.fits 7 -- ft950802_0233_2030G202270H.fits 8 -- ft950802_0233_2030G202870H.fits 9 -- ft950802_0233_2030G203770H.fits 10 -- ft950802_0233_2030G204570H.fits 11 -- ft950802_0233_2030G205070H.fits 12 -- ft950802_0233_2030G205270H.fits 13 -- ft950802_0233_2030G205870H.fits 14 -- ft950802_0233_2030G206570H.fits 15 -- ft950802_0233_2030G206770H.fits 16 -- ft950802_0233_2030G207470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g200270m.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G201370M.fits 2 -- ft950802_0233_2030G201770M.fits 3 -- ft950802_0233_2030G201970M.fits 4 -- ft950802_0233_2030G202170M.fits 5 -- ft950802_0233_2030G202370M.fits 6 -- ft950802_0233_2030G202770M.fits 7 -- ft950802_0233_2030G203670M.fits 8 -- ft950802_0233_2030G204470M.fits 9 -- ft950802_0233_2030G204970M.fits 10 -- ft950802_0233_2030G205970M.fits 11 -- ft950802_0233_2030G206870M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G201370M.fits 2 -- ft950802_0233_2030G201770M.fits 3 -- ft950802_0233_2030G201970M.fits 4 -- ft950802_0233_2030G202170M.fits 5 -- ft950802_0233_2030G202370M.fits 6 -- ft950802_0233_2030G202770M.fits 7 -- ft950802_0233_2030G203670M.fits 8 -- ft950802_0233_2030G204470M.fits 9 -- ft950802_0233_2030G204970M.fits 10 -- ft950802_0233_2030G205970M.fits 11 -- ft950802_0233_2030G206870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g200370l.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G200270L.fits 2 -- ft950802_0233_2030G200770L.fits 3 -- ft950802_0233_2030G201270L.fits 4 -- ft950802_0233_2030G201670L.fits 5 -- ft950802_0233_2030G202970L.fits 6 -- ft950802_0233_2030G203270L.fits 7 -- ft950802_0233_2030G203870L.fits 8 -- ft950802_0233_2030G204070L.fits 9 -- ft950802_0233_2030G204670L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G200270L.fits 2 -- ft950802_0233_2030G200770L.fits 3 -- ft950802_0233_2030G201270L.fits 4 -- ft950802_0233_2030G201670L.fits 5 -- ft950802_0233_2030G202970L.fits 6 -- ft950802_0233_2030G203270L.fits 7 -- ft950802_0233_2030G203870L.fits 8 -- ft950802_0233_2030G204070L.fits 9 -- ft950802_0233_2030G204670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g200470m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G203570M.fits 2 -- ft950802_0233_2030G204370M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G203570M.fits 2 -- ft950802_0233_2030G204370M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft950802_0233_2030G201570L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G201570L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G201570L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000306 events
ft950802_0233_2030G205770H.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G204270M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G204170M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G203470M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G203370M.fits-> Ignoring the following files containing 000000146 events
ft950802_0233_2030G200570H.fits ft950802_0233_2030G201070H.fits-> Ignoring the following files containing 000000080 events
ft950802_0233_2030G200970H.fits-> Ignoring the following files containing 000000074 events
ft950802_0233_2030G206470H.fits ft950802_0233_2030G207370H.fits-> Ignoring the following files containing 000000070 events
ft950802_0233_2030G200470H.fits-> Ignoring the following files containing 000000066 events
ft950802_0233_2030G200870H.fits-> Ignoring the following files containing 000000060 events
ft950802_0233_2030G200370H.fits-> Ignoring the following files containing 000000052 events
ft950802_0233_2030G205670H.fits-> Ignoring the following files containing 000000034 events
ft950802_0233_2030G203170L.fits-> Ignoring the following files containing 000000032 events
ft950802_0233_2030G206370H.fits ft950802_0233_2030G207270H.fits-> Ignoring the following files containing 000000006 events
ft950802_0233_2030G202670M.fits-> Ignoring the following files containing 000000005 events
ft950802_0233_2030G202470M.fits-> Ignoring the following files containing 000000005 events
ft950802_0233_2030G205370H.fits-> Ignoring the following files containing 000000003 events
ft950802_0233_2030G203970L.fits-> Ignoring the following files containing 000000001 events
ft950802_0233_2030G206070M.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 52 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300470h.prelist merge count = 2 photon cnt = 26 GISSORTSPLIT:LO:g300570h.prelist merge count = 2 photon cnt = 173 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 93 GISSORTSPLIT:LO:g300770h.prelist merge count = 16 photon cnt = 1298758 GISSORTSPLIT:LO:g300870h.prelist merge count = 2 photon cnt = 176 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 101 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 100 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 94 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 97 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 612 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 38 GISSORTSPLIT:LO:g300370l.prelist merge count = 9 photon cnt = 16574 GISSORTSPLIT:LO:g300470l.prelist merge count = 1 photon cnt = 512 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300270m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300370m.prelist merge count = 11 photon cnt = 105800 GISSORTSPLIT:LO:g300470m.prelist merge count = 2 photon cnt = 512 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 256 GISSORTSPLIT:LO:Total filenames split = 63 GISSORTSPLIT:LO:Total split file cnt = 25 GISSORTSPLIT:LO:End program-> Creating ad12002220g300170h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G300170H.fits 2 -- ft950802_0233_2030G300670H.fits 3 -- ft950802_0233_2030G301170H.fits 4 -- ft950802_0233_2030G301470H.fits 5 -- ft950802_0233_2030G301870H.fits 6 -- ft950802_0233_2030G302070H.fits 7 -- ft950802_0233_2030G302270H.fits 8 -- ft950802_0233_2030G302870H.fits 9 -- ft950802_0233_2030G303770H.fits 10 -- ft950802_0233_2030G304570H.fits 11 -- ft950802_0233_2030G305070H.fits 12 -- ft950802_0233_2030G305270H.fits 13 -- ft950802_0233_2030G305970H.fits 14 -- ft950802_0233_2030G306770H.fits 15 -- ft950802_0233_2030G306970H.fits 16 -- ft950802_0233_2030G307770H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G300170H.fits 2 -- ft950802_0233_2030G300670H.fits 3 -- ft950802_0233_2030G301170H.fits 4 -- ft950802_0233_2030G301470H.fits 5 -- ft950802_0233_2030G301870H.fits 6 -- ft950802_0233_2030G302070H.fits 7 -- ft950802_0233_2030G302270H.fits 8 -- ft950802_0233_2030G302870H.fits 9 -- ft950802_0233_2030G303770H.fits 10 -- ft950802_0233_2030G304570H.fits 11 -- ft950802_0233_2030G305070H.fits 12 -- ft950802_0233_2030G305270H.fits 13 -- ft950802_0233_2030G305970H.fits 14 -- ft950802_0233_2030G306770H.fits 15 -- ft950802_0233_2030G306970H.fits 16 -- ft950802_0233_2030G307770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g300270m.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G301370M.fits 2 -- ft950802_0233_2030G301770M.fits 3 -- ft950802_0233_2030G301970M.fits 4 -- ft950802_0233_2030G302170M.fits 5 -- ft950802_0233_2030G302370M.fits 6 -- ft950802_0233_2030G302770M.fits 7 -- ft950802_0233_2030G303670M.fits 8 -- ft950802_0233_2030G304470M.fits 9 -- ft950802_0233_2030G304970M.fits 10 -- ft950802_0233_2030G306070M.fits 11 -- ft950802_0233_2030G307070M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G301370M.fits 2 -- ft950802_0233_2030G301770M.fits 3 -- ft950802_0233_2030G301970M.fits 4 -- ft950802_0233_2030G302170M.fits 5 -- ft950802_0233_2030G302370M.fits 6 -- ft950802_0233_2030G302770M.fits 7 -- ft950802_0233_2030G303670M.fits 8 -- ft950802_0233_2030G304470M.fits 9 -- ft950802_0233_2030G304970M.fits 10 -- ft950802_0233_2030G306070M.fits 11 -- ft950802_0233_2030G307070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g300370l.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G300270L.fits 2 -- ft950802_0233_2030G300770L.fits 3 -- ft950802_0233_2030G301270L.fits 4 -- ft950802_0233_2030G301670L.fits 5 -- ft950802_0233_2030G302970L.fits 6 -- ft950802_0233_2030G303270L.fits 7 -- ft950802_0233_2030G303870L.fits 8 -- ft950802_0233_2030G304070L.fits 9 -- ft950802_0233_2030G304670L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G300270L.fits 2 -- ft950802_0233_2030G300770L.fits 3 -- ft950802_0233_2030G301270L.fits 4 -- ft950802_0233_2030G301670L.fits 5 -- ft950802_0233_2030G302970L.fits 6 -- ft950802_0233_2030G303270L.fits 7 -- ft950802_0233_2030G303870L.fits 8 -- ft950802_0233_2030G304070L.fits 9 -- ft950802_0233_2030G304670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft950802_0233_2030G305470H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G305470H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G305470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220g300570m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G303570M.fits 2 -- ft950802_0233_2030G304370M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G303570M.fits 2 -- ft950802_0233_2030G304370M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft950802_0233_2030G301570L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030G301570L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030G301570L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G303470M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G303370M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G304270M.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030G304170M.fits-> Ignoring the following files containing 000000176 events
ft950802_0233_2030G300570H.fits ft950802_0233_2030G301070H.fits-> Ignoring the following files containing 000000173 events
ft950802_0233_2030G306670H.fits ft950802_0233_2030G307670H.fits-> Ignoring the following files containing 000000101 events
ft950802_0233_2030G300370H.fits-> Ignoring the following files containing 000000100 events
ft950802_0233_2030G300470H.fits-> Ignoring the following files containing 000000097 events
ft950802_0233_2030G300970H.fits-> Ignoring the following files containing 000000094 events
ft950802_0233_2030G300870H.fits-> Ignoring the following files containing 000000093 events
ft950802_0233_2030G305370H.fits-> Ignoring the following files containing 000000052 events
ft950802_0233_2030G305870H.fits-> Ignoring the following files containing 000000038 events
ft950802_0233_2030G303170L.fits-> Ignoring the following files containing 000000026 events
ft950802_0233_2030G306570H.fits ft950802_0233_2030G307570H.fits-> Ignoring the following files containing 000000006 events
ft950802_0233_2030G303970L.fits-> Ignoring the following files containing 000000005 events
ft950802_0233_2030G306470H.fits ft950802_0233_2030G307470H.fits-> Ignoring the following files containing 000000004 events
ft950802_0233_2030G302670M.fits-> Ignoring the following files containing 000000003 events
ft950802_0233_2030G302470M.fits-> Ignoring the following files containing 000000001 events
ft950802_0233_2030G305570H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 306 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 7 photon cnt = 262716 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 12 photon cnt = 702374 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 1 photon cnt = 312 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 1 photon cnt = 6 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 1 photon cnt = 256 SIS0SORTSPLIT:LO:s000701l.prelist merge count = 2 photon cnt = 5829 SIS0SORTSPLIT:LO:s000801m.prelist merge count = 5 photon cnt = 40905 SIS0SORTSPLIT:LO:s000901m.prelist merge count = 2 photon cnt = 64 SIS0SORTSPLIT:LO:s001002h.prelist merge count = 2 photon cnt = 1297 SIS0SORTSPLIT:LO:s001102l.prelist merge count = 7 photon cnt = 10092 SIS0SORTSPLIT:LO:s001202l.prelist merge count = 2 photon cnt = 69 SIS0SORTSPLIT:LO:s001302m.prelist merge count = 5 photon cnt = 110866 SIS0SORTSPLIT:LO:Total filenames split = 48 SIS0SORTSPLIT:LO:Total split file cnt = 13 SIS0SORTSPLIT:LO:End program-> Creating ad12002220s000101h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S000101H.fits 2 -- ft950802_0233_2030S000401H.fits 3 -- ft950802_0233_2030S000601H.fits 4 -- ft950802_0233_2030S001901H.fits 5 -- ft950802_0233_2030S002101H.fits 6 -- ft950802_0233_2030S002301H.fits 7 -- ft950802_0233_2030S002501H.fits 8 -- ft950802_0233_2030S002701H.fits 9 -- ft950802_0233_2030S002901H.fits 10 -- ft950802_0233_2030S005401H.fits 11 -- ft950802_0233_2030S005601H.fits 12 -- ft950802_0233_2030S006001H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S000101H.fits 2 -- ft950802_0233_2030S000401H.fits 3 -- ft950802_0233_2030S000601H.fits 4 -- ft950802_0233_2030S001901H.fits 5 -- ft950802_0233_2030S002101H.fits 6 -- ft950802_0233_2030S002301H.fits 7 -- ft950802_0233_2030S002501H.fits 8 -- ft950802_0233_2030S002701H.fits 9 -- ft950802_0233_2030S002901H.fits 10 -- ft950802_0233_2030S005401H.fits 11 -- ft950802_0233_2030S005601H.fits 12 -- ft950802_0233_2030S006001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000201h.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S001201H.fits 2 -- ft950802_0233_2030S001701H.fits 3 -- ft950802_0233_2030S003401H.fits 4 -- ft950802_0233_2030S003601H.fits 5 -- ft950802_0233_2030S004201H.fits 6 -- ft950802_0233_2030S004801H.fits 7 -- ft950802_0233_2030S005001H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S001201H.fits 2 -- ft950802_0233_2030S001701H.fits 3 -- ft950802_0233_2030S003401H.fits 4 -- ft950802_0233_2030S003601H.fits 5 -- ft950802_0233_2030S004201H.fits 6 -- ft950802_0233_2030S004801H.fits 7 -- ft950802_0233_2030S005001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000302m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S001002M.fits 2 -- ft950802_0233_2030S001502M.fits 3 -- ft950802_0233_2030S003202M.fits 4 -- ft950802_0233_2030S004002M.fits 5 -- ft950802_0233_2030S004702M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S001002M.fits 2 -- ft950802_0233_2030S001502M.fits 3 -- ft950802_0233_2030S003202M.fits 4 -- ft950802_0233_2030S004002M.fits 5 -- ft950802_0233_2030S004702M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000401m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S001801M.fits 2 -- ft950802_0233_2030S002001M.fits 3 -- ft950802_0233_2030S002201M.fits 4 -- ft950802_0233_2030S005101M.fits 5 -- ft950802_0233_2030S005701M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S001801M.fits 2 -- ft950802_0233_2030S002001M.fits 3 -- ft950802_0233_2030S002201M.fits 4 -- ft950802_0233_2030S005101M.fits 5 -- ft950802_0233_2030S005701M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000502l.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S000902L.fits 2 -- ft950802_0233_2030S001402L.fits 3 -- ft950802_0233_2030S003102L.fits 4 -- ft950802_0233_2030S003702L.fits 5 -- ft950802_0233_2030S003902L.fits 6 -- ft950802_0233_2030S004302L.fits 7 -- ft950802_0233_2030S004502L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S000902L.fits 2 -- ft950802_0233_2030S001402L.fits 3 -- ft950802_0233_2030S003102L.fits 4 -- ft950802_0233_2030S003702L.fits 5 -- ft950802_0233_2030S003902L.fits 6 -- ft950802_0233_2030S004302L.fits 7 -- ft950802_0233_2030S004502L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000601l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S000201L.fits 2 -- ft950802_0233_2030S000501L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S000201L.fits 2 -- ft950802_0233_2030S000501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s000702h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S000802H.fits 2 -- ft950802_0233_2030S001302H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S000802H.fits 2 -- ft950802_0233_2030S001302H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000312 events
ft950802_0233_2030S002401H.fits-> Ignoring the following files containing 000000306 events
ft950802_0233_2030S002601H.fits-> Ignoring the following files containing 000000256 events
ft950802_0233_2030S002801H.fits-> Ignoring the following files containing 000000069 events
ft950802_0233_2030S003802L.fits ft950802_0233_2030S004402L.fits-> Ignoring the following files containing 000000064 events
ft950802_0233_2030S005201M.fits ft950802_0233_2030S005801M.fits-> Ignoring the following files containing 000000006 events
ft950802_0233_2030S003501H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 7 photon cnt = 239066 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 13 photon cnt = 803353 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 130 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 1 photon cnt = 152 SIS1SORTSPLIT:LO:s100501h.prelist merge count = 1 photon cnt = 81 SIS1SORTSPLIT:LO:s100601l.prelist merge count = 2 photon cnt = 6427 SIS1SORTSPLIT:LO:s100701m.prelist merge count = 5 photon cnt = 47441 SIS1SORTSPLIT:LO:s100801m.prelist merge count = 2 photon cnt = 64 SIS1SORTSPLIT:LO:s100902h.prelist merge count = 2 photon cnt = 1555 SIS1SORTSPLIT:LO:s101002l.prelist merge count = 7 photon cnt = 18368 SIS1SORTSPLIT:LO:s101102l.prelist merge count = 2 photon cnt = 51 SIS1SORTSPLIT:LO:s101202m.prelist merge count = 5 photon cnt = 116252 SIS1SORTSPLIT:LO:Total filenames split = 48 SIS1SORTSPLIT:LO:Total split file cnt = 12 SIS1SORTSPLIT:LO:End program-> Creating ad12002220s100101h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S100101H.fits 2 -- ft950802_0233_2030S100401H.fits 3 -- ft950802_0233_2030S100601H.fits 4 -- ft950802_0233_2030S101801H.fits 5 -- ft950802_0233_2030S102001H.fits 6 -- ft950802_0233_2030S102201H.fits 7 -- ft950802_0233_2030S102401H.fits 8 -- ft950802_0233_2030S102601H.fits 9 -- ft950802_0233_2030S102801H.fits 10 -- ft950802_0233_2030S105001H.fits 11 -- ft950802_0233_2030S105401H.fits 12 -- ft950802_0233_2030S105601H.fits 13 -- ft950802_0233_2030S106001H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S100101H.fits 2 -- ft950802_0233_2030S100401H.fits 3 -- ft950802_0233_2030S100601H.fits 4 -- ft950802_0233_2030S101801H.fits 5 -- ft950802_0233_2030S102001H.fits 6 -- ft950802_0233_2030S102201H.fits 7 -- ft950802_0233_2030S102401H.fits 8 -- ft950802_0233_2030S102601H.fits 9 -- ft950802_0233_2030S102801H.fits 10 -- ft950802_0233_2030S105001H.fits 11 -- ft950802_0233_2030S105401H.fits 12 -- ft950802_0233_2030S105601H.fits 13 -- ft950802_0233_2030S106001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100201h.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S101201H.fits 2 -- ft950802_0233_2030S101701H.fits 3 -- ft950802_0233_2030S103301H.fits 4 -- ft950802_0233_2030S103501H.fits 5 -- ft950802_0233_2030S104101H.fits 6 -- ft950802_0233_2030S104701H.fits 7 -- ft950802_0233_2030S104901H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S101201H.fits 2 -- ft950802_0233_2030S101701H.fits 3 -- ft950802_0233_2030S103301H.fits 4 -- ft950802_0233_2030S103501H.fits 5 -- ft950802_0233_2030S104101H.fits 6 -- ft950802_0233_2030S104701H.fits 7 -- ft950802_0233_2030S104901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100302m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S101002M.fits 2 -- ft950802_0233_2030S101502M.fits 3 -- ft950802_0233_2030S103102M.fits 4 -- ft950802_0233_2030S103902M.fits 5 -- ft950802_0233_2030S104602M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S101002M.fits 2 -- ft950802_0233_2030S101502M.fits 3 -- ft950802_0233_2030S103102M.fits 4 -- ft950802_0233_2030S103902M.fits 5 -- ft950802_0233_2030S104602M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100401m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S101901M.fits 2 -- ft950802_0233_2030S102101M.fits 3 -- ft950802_0233_2030S102301M.fits 4 -- ft950802_0233_2030S105101M.fits 5 -- ft950802_0233_2030S105701M.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S101901M.fits 2 -- ft950802_0233_2030S102101M.fits 3 -- ft950802_0233_2030S102301M.fits 4 -- ft950802_0233_2030S105101M.fits 5 -- ft950802_0233_2030S105701M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100502l.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S100902L.fits 2 -- ft950802_0233_2030S101402L.fits 3 -- ft950802_0233_2030S103002L.fits 4 -- ft950802_0233_2030S103602L.fits 5 -- ft950802_0233_2030S103802L.fits 6 -- ft950802_0233_2030S104202L.fits 7 -- ft950802_0233_2030S104402L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S100902L.fits 2 -- ft950802_0233_2030S101402L.fits 3 -- ft950802_0233_2030S103002L.fits 4 -- ft950802_0233_2030S103602L.fits 5 -- ft950802_0233_2030S103802L.fits 6 -- ft950802_0233_2030S104202L.fits 7 -- ft950802_0233_2030S104402L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100601l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S100201L.fits 2 -- ft950802_0233_2030S100501L.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S100201L.fits 2 -- ft950802_0233_2030S100501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad12002220s100702h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950802_0233_2030S100802H.fits 2 -- ft950802_0233_2030S101302H.fits Merging binary extension #: 2 1 -- ft950802_0233_2030S100802H.fits 2 -- ft950802_0233_2030S101302H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000152 events
ft950802_0233_2030S103401H.fits-> Ignoring the following files containing 000000130 events
ft950802_0233_2030S102501H.fits-> Ignoring the following files containing 000000081 events
ft950802_0233_2030S102701H.fits-> Ignoring the following files containing 000000064 events
ft950802_0233_2030S105201M.fits ft950802_0233_2030S105801M.fits-> Ignoring the following files containing 000000051 events
ft950802_0233_2030S103702L.fits ft950802_0233_2030S104302L.fits-> Tar-ing together the leftover raw files
a ft950802_0233_2030G200370H.fits 40K a ft950802_0233_2030G200470H.fits 40K a ft950802_0233_2030G200570H.fits 40K a ft950802_0233_2030G200870H.fits 40K a ft950802_0233_2030G200970H.fits 40K a ft950802_0233_2030G201070H.fits 40K a ft950802_0233_2030G202470M.fits 40K a ft950802_0233_2030G202670M.fits 40K a ft950802_0233_2030G203170L.fits 40K a ft950802_0233_2030G203370M.fits 45K a ft950802_0233_2030G203470M.fits 45K a ft950802_0233_2030G203970L.fits 40K a ft950802_0233_2030G204170M.fits 45K a ft950802_0233_2030G204270M.fits 45K a ft950802_0233_2030G205370H.fits 40K a ft950802_0233_2030G205670H.fits 40K a ft950802_0233_2030G205770H.fits 48K a ft950802_0233_2030G206070M.fits 40K a ft950802_0233_2030G206370H.fits 40K a ft950802_0233_2030G206470H.fits 40K a ft950802_0233_2030G207270H.fits 40K a ft950802_0233_2030G207370H.fits 40K a ft950802_0233_2030G300370H.fits 43K a ft950802_0233_2030G300470H.fits 43K a ft950802_0233_2030G300570H.fits 40K a ft950802_0233_2030G300870H.fits 40K a ft950802_0233_2030G300970H.fits 43K a ft950802_0233_2030G301070H.fits 40K a ft950802_0233_2030G302470M.fits 40K a ft950802_0233_2030G302670M.fits 40K a ft950802_0233_2030G303170L.fits 40K a ft950802_0233_2030G303370M.fits 45K a ft950802_0233_2030G303470M.fits 45K a ft950802_0233_2030G303970L.fits 40K a ft950802_0233_2030G304170M.fits 45K a ft950802_0233_2030G304270M.fits 45K a ft950802_0233_2030G305370H.fits 40K a ft950802_0233_2030G305570H.fits 40K a ft950802_0233_2030G305870H.fits 40K a ft950802_0233_2030G306470H.fits 40K a ft950802_0233_2030G306570H.fits 40K a ft950802_0233_2030G306670H.fits 40K a ft950802_0233_2030G307470H.fits 40K a ft950802_0233_2030G307570H.fits 40K a ft950802_0233_2030G307670H.fits 40K a ft950802_0233_2030S002401H.fits 51K a ft950802_0233_2030S002601H.fits 51K a ft950802_0233_2030S002801H.fits 48K a ft950802_0233_2030S003501H.fits 40K a ft950802_0233_2030S003802L.fits 40K a ft950802_0233_2030S004402L.fits 40K a ft950802_0233_2030S005201M.fits 40K a ft950802_0233_2030S005801M.fits 40K a ft950802_0233_2030S102501H.fits 43K a ft950802_0233_2030S102701H.fits 43K a ft950802_0233_2030S103401H.fits 45K a ft950802_0233_2030S103702L.fits 40K a ft950802_0233_2030S104302L.fits 40K a ft950802_0233_2030S105201M.fits 40K a ft950802_0233_2030S105801M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft950802_0233.2030 'ft950802_0233.2030' is successfully opened Data Start Time is 81484437.68 (950802 023357) Time Margin 2.0 sec included Sync error detected in 0 th SF Sync error detected in 1 th SF Sync error detected in 5 th SF Sync error detected in 8 th SF Sync error detected in 9 th SF Sync error detected in 15 th SF Sync error detected in 35 th SF Sync error detected in 36 th SF Sync error detected in 3010 th SF Sync error detected in 3011 th SF Sync error detected in 3012 th SF Sync error detected in 3022 th SF Sync error detected in 3131 th SF Sync error detected in 3139 th SF Sync error detected in 4375 th SF Sync error detected in 4377 th SF Sync error detected in 4378 th SF Sync error detected in 4448 th SF 'ft950802_0233.2030' EOF detected, sf=16024 Data End Time is 81549033.48 (950802 203033) Gain History is written in ft950802_0233_2030.ghf-> Checking if column CAL_START in ft950802_0233_2030.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft950802_0233_2030.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad12002220g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g200470m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g200570l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300570m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220g300670l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000401m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000412m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000502l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000602l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000612l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s000702h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100401m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100412m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100502l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100602l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100612l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad12002220s100702h.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 95/ 8/ 2 2:33 mjd=49931.106250 Orbit file name is ./frf.orbit.204 Epoch of Orbital Elements: 1995/8/1 0:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa950802_0233.2030 S0-HK file: ft950802_0233_2030S0HK.fits S1-HK file: ft950802_0233_2030S1HK.fits G2-HK file: ft950802_0233_2030G2HK.fits G3-HK file: ft950802_0233_2030G3HK.fits output FITS File: ft950802_0233_2030.mkf Total 2018 Data bins were processed.-> Checking if column TIME in ft950802_0233_2030.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 10552.451 The mean of the selected column is 48.628808 The standard deviation of the selected column is 14.004851 The minimum of selected column is 23.687603 The maximum of selected column is 163.46927 The number of points used in calculation is 217-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9900.3774 The mean of the selected column is 45.207203 The standard deviation of the selected column is 64.116004 The minimum of selected column is 17.225054 The maximum of selected column is 751.81488 The number of points used in calculation is 219-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8553.5851 The mean of the selected column is 39.417443 The standard deviation of the selected column is 28.677379 The minimum of selected column is 18.562559 The maximum of selected column is 358.78238 The number of points used in calculation is 217-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>6.6 && S0_PIXL0<90.6 )&& (S0_PIXL1>0)&& (S0_PIXL2>0.0 && S0_PIXL2<237.5 )&& (S0_PIXL3>0.0 && S0_PIXL3<125.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.18E+05 554010 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
415162 594 0 414568 0 0
Writing events file
594 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
415162 594 0 414568 0 0
in 21.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 594
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 594
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 284 188 31 91
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 284 188 31 91
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 594
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000102h.evt use_events=no
Wrote cleaned events file to ad12002220s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad12002220s000112h.unf into ad12002220s000112h.evtThe sum of the selected column is 10552.451 The mean of the selected column is 48.628808 The standard deviation of the selected column is 14.004851 The minimum of selected column is 23.687603 The maximum of selected column is 163.46927 The number of points used in calculation is 217-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9900.3774 The mean of the selected column is 45.207203 The standard deviation of the selected column is 64.116004 The minimum of selected column is 17.225054 The maximum of selected column is 751.81488 The number of points used in calculation is 219-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8553.5851 The mean of the selected column is 39.417443 The standard deviation of the selected column is 28.677379 The minimum of selected column is 18.562559 The maximum of selected column is 358.78238 The number of points used in calculation is 217-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>6.6 && S0_PIXL0<90.6 )&& (S0_PIXL1>0)&& (S0_PIXL2>0.0 && S0_PIXL2<237.5 )&& (S0_PIXL3>0.0 && S0_PIXL3<125.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.18E+05 569248 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
455224 635 0 454589 0 0
Writing events file
635 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
455224 635 0 454589 0 0
in 21.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 635
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 635
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 305 198 33 99
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 305 198 33 99
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 635
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad12002220s000112h.evt use_events=no
Wrote cleaned events file to ad12002220s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad12002220s000201h.unf because of modeThe sum of the selected column is 9556.9993 The mean of the selected column is 74.085266 The standard deviation of the selected column is 7.5858377 The minimum of selected column is 58.187679 The maximum of selected column is 104.31283 The number of points used in calculation is 129-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3721.6369 The mean of the selected column is 28.849898 The standard deviation of the selected column is 9.7593104 The minimum of selected column is 9.7187805 The maximum of selected column is 61.406448 The number of points used in calculation is 129-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>51.3 && S0_PIXL1<96.8 )&& (S0_PIXL2>0.0 && S0_PIXL2<58.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.91E+04 234025 0110
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
215586 183785 0 31801 0 0
Writing events file
183785 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
215586 183785 0 31801 0 0
in 7556.07 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 183785
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 17 78
cleaning chip # 2
Hot pixels & counts : 10 4035
Flickering pixels iter, pixels & cnts : 1 4 35
cleaning chip # 3
Number of pixels rejected : 31
Number of (internal) image counts : 183785
Number of image cts rejected (N, %) : 4148 2.2569849
By chip : 0 1 2 3
Pixels rejected : 0 17 14 0
Image counts : 0 173945 9840 0
Image cts rejected: 0 78 4070 0
Image cts rej (%) : 0.00 0.04 41.36 0.00
filtering data...
Total counts : 0 173945 9840 0
Total cts rejected: 0 78 4070 0
Total cts rej (%) : 0.00 0.04 41.36 0.00
Number of clean counts accepted : 179637
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 31
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000202h.evt use_events=no
Wrote cleaned events file to ad12002220s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad12002220s000212h.unf into ad12002220s000212h.evtThe sum of the selected column is 9556.9993 The mean of the selected column is 74.085266 The standard deviation of the selected column is 7.5858377 The minimum of selected column is 58.187679 The maximum of selected column is 104.31283 The number of points used in calculation is 129-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3721.6369 The mean of the selected column is 28.849898 The standard deviation of the selected column is 9.7593104 The minimum of selected column is 9.7187805 The maximum of selected column is 61.406448 The number of points used in calculation is 129-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>51.3 && S0_PIXL1<96.8 )&& (S0_PIXL2>0.0 && S0_PIXL2<58.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.91E+04 235064 0110
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
217597 185369 0 32228 0 0
Writing events file
185369 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
217597 185369 0 32228 0 0
in 7556.07 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 185369
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 16 76
cleaning chip # 2
Hot pixels & counts : 10 4040
Flickering pixels iter, pixels & cnts : 1 5 38
cleaning chip # 3
Number of pixels rejected : 31
Number of (internal) image counts : 185369
Number of image cts rejected (N, %) : 4154 2.2409356
By chip : 0 1 2 3
Pixels rejected : 0 16 15 0
Image counts : 0 175436 9933 0
Image cts rejected: 0 76 4078 0
Image cts rej (%) : 0.00 0.04 41.06 0.00
filtering data...
Total counts : 0 175436 9933 0
Total cts rejected: 0 76 4078 0
Total cts rej (%) : 0.00 0.04 41.06 0.00
Number of clean counts accepted : 181215
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 31
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad12002220s000212h.evt use_events=no
Wrote cleaned events file to ad12002220s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad12002220s000302m.unf into ad12002220s000302m.evtThe sum of the selected column is 1401.2735 The mean of the selected column is 66.727310 The standard deviation of the selected column is 15.198342 The minimum of selected column is 6.7379470 The maximum of selected column is 82.000252 The number of points used in calculation is 21-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2660.5194 The mean of the selected column is 21.284155 The standard deviation of the selected column is 9.5548624 The minimum of selected column is 1.7298499 The maximum of selected column is 70.250221 The number of points used in calculation is 125-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>21.1 && S0_PIXL1<112.3 )&& (S0_PIXL2>0.0 && S0_PIXL2<49.9 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.64E+04 110866 0110
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
102983 10385 0 92598 0 0
Writing events file
10385 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
102983 10385 0 92598 0 0
in 653.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 10385
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 8 28
cleaning chip # 2
Hot pixels & counts : 5 276
Flickering pixels iter, pixels & cnts : 1 4 21
cleaning chip # 3
Number of pixels rejected : 17
Number of (internal) image counts : 10385
Number of image cts rejected (N, %) : 325 3.1295137
By chip : 0 1 2 3
Pixels rejected : 0 8 9 0
Image counts : 0 9595 790 0
Image cts rejected: 0 28 297 0
Image cts rej (%) : 0.00 0.29 37.59 0.00
filtering data...
Total counts : 0 9595 790 0
Total cts rejected: 0 28 297 0
Total cts rej (%) : 0.00 0.29 37.59 0.00
Number of clean counts accepted : 10060
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 17
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000302m.evt use_events=no
Wrote cleaned events file to ad12002220s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad12002220s000401m.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 08:00:09 0.63E+04 5816 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000402m.evt use_events=no
Wrote cleaned events file to ad12002220s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000402m.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 MEDIUM 02/08/95 08:00:09 0.63E+04 5942 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000412m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad12002220s000412m.evt use_events=no
Wrote cleaned events file to ad12002220s000412m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s000412m.evt since it contains 0 eventsThe sum of the selected column is 75.062576 The mean of the selected column is 25.020859 The standard deviation of the selected column is 7.7548117 The minimum of selected column is 16.250027 The maximum of selected column is 30.968800 The number of points used in calculation is 3-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>1.7 && S0_PIXL2<48.2 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.96E+04 10092 0110
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000502l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000502l.evt use_events=no
Wrote cleaned events file to ad12002220s000502l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000502l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 02:41:45 0.33E+04 2518 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000602l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000602l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000602l.evt use_events=no
Wrote cleaned events file to ad12002220s000602l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000602l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 LOW 02/08/95 02:41:45 0.33E+04 2590 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000612l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000612l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad12002220s000612l.evt use_events=no
Wrote cleaned events file to ad12002220s000612l.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s000612l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0)&& (S0_PIXL2>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.48E+02 1297 0110
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
981 551 0 430 0 0
Writing events file
551 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
981 551 0 430 0 0
in 28.07 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 551
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 4 15
cleaning chip # 3
Number of pixels rejected : 4
Number of (internal) image counts : 551
Number of image cts rejected (N, %) : 15 2.7223229
By chip : 0 1 2 3
Pixels rejected : 0 0 4 0
Image counts : 0 512 39 0
Image cts rejected: 0 0 15 0
Image cts rej (%) : 0.00 0.00 38.46 0.00
filtering data...
Total counts : 0 512 39 0
Total cts rejected: 0 0 15 0
Total cts rej (%) : 0.00 0.00 38.46 0.00
Number of clean counts accepted : 536
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 4
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s000702h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad12002220s000702h.evt use_events=no
Wrote cleaned events file to ad12002220s000702h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad12002220s100101h.unf because of modeThe sum of the selected column is 15488.730 The mean of the selected column is 70.084750 The standard deviation of the selected column is 18.146550 The minimum of selected column is 15.218822 The maximum of selected column is 182.50058 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14136.589 The mean of the selected column is 63.966466 The standard deviation of the selected column is 16.850765 The minimum of selected column is 10.171923 The maximum of selected column is 145.93796 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12922.083 The mean of the selected column is 58.470964 The standard deviation of the selected column is 13.455828 The minimum of selected column is 20.812592 The maximum of selected column is 100.21906 The number of points used in calculation is 221-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>15.6 && S1_PIXL0<124.5 )&& (S1_PIXL1>13.4 && S1_PIXL1<114.5 )&& (S1_PIXL2>18.1 && S1_PIXL2<98.8 )&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.18E+05 677303 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100102h.unf
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
screen:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> Filtering ad12002220s100112h.unf into ad12002220s100112h.evtThe sum of the selected column is 15488.730 The mean of the selected column is 70.084750 The standard deviation of the selected column is 18.146550 The minimum of selected column is 15.218822 The maximum of selected column is 182.50058 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14136.589 The mean of the selected column is 63.966466 The standard deviation of the selected column is 16.850765 The minimum of selected column is 10.171923 The maximum of selected column is 145.93796 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12922.083 The mean of the selected column is 58.470964 The standard deviation of the selected column is 13.455828 The minimum of selected column is 20.812592 The maximum of selected column is 100.21906 The number of points used in calculation is 221-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>15.6 && S1_PIXL0<124.5 )&& (S1_PIXL1>13.4 && S1_PIXL1<114.5 )&& (S1_PIXL2>18.1 && S1_PIXL2<98.8 )&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.18E+05 699695 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100112h.unf
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
screen:ASCA-SIS1-BRIGHT2 > Session saved, goodbye
-> Skipping ad12002220s100201h.unf because of modeThe sum of the selected column is 6441.7840 The mean of the selected column is 49.552185 The standard deviation of the selected column is 17.850633 The minimum of selected column is 10.232233 The maximum of selected column is 114.65661 The number of points used in calculation is 130-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10046.608 The mean of the selected column is 77.281601 The standard deviation of the selected column is 13.854350 The minimum of selected column is 24.232361 The maximum of selected column is 122.12540 The number of points used in calculation is 130-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<103.1 )&& (S1_PIXL3>35.7 && S1_PIXL3<118.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.91E+04 215087 1001
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
197335 168500 0 28835 0 0
Writing events file
168500 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
197335 168500 0 28835 0 0
in 7609.58 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 168500
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 22 10119
Flickering pixels iter, pixels & cnts : 1 9 121
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 22 489
Number of pixels rejected : 53
Number of (internal) image counts : 168500
Number of image cts rejected (N, %) : 10729 6.3673592
By chip : 0 1 2 3
Pixels rejected : 31 0 0 22
Image counts : 16033 0 0 152467
Image cts rejected: 10240 0 0 489
Image cts rej (%) : 63.87 0.00 0.00 0.32
filtering data...
Total counts : 16033 0 0 152467
Total cts rejected: 10240 0 0 489
Total cts rej (%) : 63.87 0.00 0.00 0.32
Number of clean counts accepted : 157771
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 53
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100202h.evt use_events=no
Wrote cleaned events file to ad12002220s100202h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad12002220s100212h.unf into ad12002220s100212h.evtThe sum of the selected column is 6441.7840 The mean of the selected column is 49.552185 The standard deviation of the selected column is 17.850633 The minimum of selected column is 10.232233 The maximum of selected column is 114.65661 The number of points used in calculation is 130-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10046.608 The mean of the selected column is 77.281601 The standard deviation of the selected column is 13.854350 The minimum of selected column is 24.232361 The maximum of selected column is 122.12540 The number of points used in calculation is 130-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<103.1 )&& (S1_PIXL3>35.7 && S1_PIXL3<118.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.91E+04 215555 1001
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
198719 169689 0 29030 0 0
Writing events file
169689 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
198719 169689 0 29030 0 0
in 7609.58 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 169689
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 22 10133
Flickering pixels iter, pixels & cnts : 1 9 128
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 21 489
Number of pixels rejected : 52
Number of (internal) image counts : 169689
Number of image cts rejected (N, %) : 10750 6.3351188
By chip : 0 1 2 3
Pixels rejected : 31 0 0 21
Image counts : 16120 0 0 153569
Image cts rejected: 10261 0 0 489
Image cts rej (%) : 63.65 0.00 0.00 0.32
filtering data...
Total counts : 16120 0 0 153569
Total cts rejected: 10261 0 0 489
Total cts rej (%) : 63.65 0.00 0.00 0.32
Number of clean counts accepted : 158939
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 52
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad12002220s100212h.evt use_events=no
Wrote cleaned events file to ad12002220s100212h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad12002220s100302m.unf into ad12002220s100302m.evtThe sum of the selected column is 4348.2918 The mean of the selected column is 34.786334 The standard deviation of the selected column is 12.660294 The minimum of selected column is 3.5282488 The maximum of selected column is 97.562805 The number of points used in calculation is 125-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<72.7 )&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.64E+04 116252 1001
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
106922 0 0 106922 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
106922 0 0 106922 0 0
in 1.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100302m.evt use_events=no
Wrote cleaned events file to ad12002220s100302m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100302m.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 08:00:09 0.63E+04 7278 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100402m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100402m.evt use_events=no
Wrote cleaned events file to ad12002220s100402m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100402m.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 MEDIUM 02/08/95 08:00:09 0.63E+04 7531 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100412m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100412m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad12002220s100412m.evt use_events=no
Wrote cleaned events file to ad12002220s100412m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s100412m.evt since it contains 0 eventsThe sum of the selected column is 237.34414 The mean of the selected column is 79.114713 The standard deviation of the selected column is 53.848196 The minimum of selected column is 21.031250 The maximum of selected column is 127.37523 The number of points used in calculation is 3-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<240.6 )&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.96E+04 18368 1001
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
16420 245 0 16175 0 0
Writing events file
245 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16420 245 0 16175 0 0
in 32.28 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 245
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 2
Number of (internal) image counts : 245
Number of image cts rejected (N, %) : 6 2.4489796
By chip : 0 1 2 3
Pixels rejected : 2 0 0 0
Image counts : 68 0 0 177
Image cts rejected: 6 0 0 0
Image cts rej (%) : 8.82 0.00 0.00 0.00
filtering data...
Total counts : 68 0 0 177
Total cts rejected: 6 0 0 0
Total cts rej (%) : 8.82 0.00 0.00 0.00
Number of clean counts accepted : 239
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 2
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100502l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100502l.evt use_events=no
Wrote cleaned events file to ad12002220s100502l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad12002220s100601l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 02:41:45 0.33E+04 3213 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100602l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100602l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100602l.evt use_events=no
Wrote cleaned events file to ad12002220s100602l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100602l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 LOW 02/08/95 02:41:45 0.33E+04 3348 1111
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100612l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100612l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad12002220s100612l.evt use_events=no
Wrote cleaned events file to ad12002220s100612l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s100612l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.48E+02 1555 1001
Processing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1226 887 0 339 0 0
Writing events file
887 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1226 887 0 339 0 0
in 28.07 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/12002220.003/screen_in_event.xsl
reading data file: /data/data23/seq_proc/12002220.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 887
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 7 21
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 7
Number of (internal) image counts : 887
Number of image cts rejected (N, %) : 21 2.3675311
By chip : 0 1 2 3
Pixels rejected : 7 0 0 0
Image counts : 130 0 0 757
Image cts rejected: 21 0 0 0
Image cts rej (%) : 16.15 0.00 0.00 0.00
filtering data...
Total counts : 130 0 0 757
Total cts rejected: 21 0 0 0
Total cts rej (%) : 16.15 0.00 0.00 0.00
Number of clean counts accepted : 866
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220s100702h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad12002220s100702h.evt use_events=no
Wrote cleaned events file to ad12002220s100702h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad12002220g200170h.unf into ad12002220g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.unf
Total Good Bad: Region Time Phase Cut
960373 737477 31551 191345 0 0
Writing events file
737477 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
960373 737477 31551 191345 0 0
in 20904.66 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
737477 732566 4911
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad12002220g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 732566 in ad12002220g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.unf
Total Good Bad: Region Time Phase Cut
105939 94672 6429 4838 0 0
Writing events file
94672 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105939 94672 6429 4838 0 0
in 6112.08 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
94672 94055 617
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad12002220g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 94055 in ad12002220g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.unf
Total Good Bad: Region Time Phase Cut
16934 8971 4312 3651 0 0
Writing events file
8971 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16934 8971 4312 3651 0 0
in 2335.90 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8971 8912 59
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad12002220g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 8912 in ad12002220g200370l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.unf
Total Good Bad: Region Time Phase Cut
512 495 17 0 0 0
Writing events file
495 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
512 495 17 0 0 0
in 32.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
495 488 7
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad12002220g200470m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 488 in ad12002220g200470m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.unf
Total Good Bad: Region Time Phase Cut
512 492 20 0 0 0
Writing events file
492 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
512 492 20 0 0 0
in 128.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
492 490 2
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad12002220g200570l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 490 in ad12002220g200570l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.unf
Total Good Bad: Region Time Phase Cut
1298758 1013825 22146 262787 0 0
Writing events file
1013825 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1298758 1013825 22146 262787 0 0
in 20900.66 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
1013825 1008298 5527
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 1008298 in ad12002220g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.unf
Total Good Bad: Region Time Phase Cut
105800 96317 4386 5097 0 0
Writing events file
96317 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105800 96317 4386 5097 0 0
in 6112.08 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
96317 95854 463
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 95854 in ad12002220g300270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.unf
Total Good Bad: Region Time Phase Cut
16574 9146 3497 3931 0 0
Writing events file
9146 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16574 9146 3497 3931 0 0
in 2335.90 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
9146 9094 52
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 9094 in ad12002220g300370l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.unf
Total Good Bad: Region Time Phase Cut
612 592 20 0 0 0
Writing events file
592 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
612 592 20 0 0 0
in 12.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
592 590 2
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300470h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 590 in ad12002220g300470h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.unf
Total Good Bad: Region Time Phase Cut
512 502 10 0 0 0
Writing events file
502 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
512 502 10 0 0 0
in 32.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
502 497 5
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300570m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300570m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 497 in ad12002220g300570m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.unf
Total Good Bad: Region Time Phase Cut
512 501 11 0 0 0
Writing events file
501 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
512 501 11 0 0 0
in 128.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
501 498 3
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!screen:ASCA > read events ad12002220g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad12002220g300670l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 498 in ad12002220g300670l.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad12002220g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4512
Mean RA/DEC/ROLL : 350.7286 58.9021 323.4512
Pnt RA/DEC/ROLL : 350.6695 58.9412 323.4512
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 67
Total GTI (secs) : 20904.656
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3305.9882812 3305.9882812
20 Percent Complete: Total/live time: 4965.9824219 4965.9824219
30 Percent Complete: Total/live time: 6996.0898438 6996.0898438
40 Percent Complete: Total/live time: 8909.0878906 8909.0878906
50 Percent Complete: Total/live time: 10898.1650391 10898.1650391
60 Percent Complete: Total/live time: 13340.2587891 13340.2587891
70 Percent Complete: Total/live time: 14842.6210938 14842.6210938
80 Percent Complete: Total/live time: 17193.7792969 17193.7792969
90 Percent Complete: Total/live time: 19593.4570312 19593.4570312
100 Percent Complete: Total/live time: 20904.6542969 20904.6542969
Number of attitude steps used: 44
Number of attitude steps avail: 53973
Mean RA/DEC pixel offset: -12.6761 -3.1967
writing expo file: ad12002220g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 731508 1058 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
732566 731508 1058 0 0 0
in 20904.66 seconds
Image has 731508 counts for 34.99 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 456599 1058 0 0 274909
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
732566 456599 1058 0 0 274909
in 20904.66 seconds
Image has 456599 counts for 21.84 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 279848 1058 0 0 451660
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
732566 279848 1058 0 0 451660
in 20904.66 seconds
Image has 279848 counts for 13.39 counts/sec
Command not found; type ? for a command listing
!ad12002220g200170h:ASCA >
!ad12002220g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g200170h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g200170h:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g200170h:ASCA-GIS2-PH > set image sky
!ad12002220g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad12002220g200170h:ASCA-GIS2-PH > extract image
!ad12002220g200170h:ASCA-GIS2-PH > save image outfile=ad12002220g200170h.img
Wrote image to file ad12002220g200170h.img
!ad12002220g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad12002220g200170h:ASCA-GIS2-PH > extract image
!ad12002220g200170h:ASCA-GIS2-PH > save image outfile=ad12002220g200170h_lo.img
Wrote image to file ad12002220g200170h_lo.img
!ad12002220g200170h:ASCA-GIS2-PH > clear pha_cut
!ad12002220g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g200170h:ASCA-GIS2-PH > extract image
!ad12002220g200170h:ASCA-GIS2-PH > save image outfile=ad12002220g200170h_hi.img
Wrote image to file ad12002220g200170h_hi.img
!ad12002220g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad12002220g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4514
Mean RA/DEC/ROLL : 350.7298 58.9021 323.4514
Pnt RA/DEC/ROLL : 350.6696 58.9418 323.4514
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 5
Total GTI (secs) : 6112.076
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 697.9659424 697.9659424
20 Percent Complete: Total/live time: 1321.9638672 1321.9638672
30 Percent Complete: Total/live time: 1925.9620361 1925.9620361
40 Percent Complete: Total/live time: 3696.0832520 3696.0832520
50 Percent Complete: Total/live time: 3696.0832520 3696.0832520
60 Percent Complete: Total/live time: 5426.0781250 5426.0781250
70 Percent Complete: Total/live time: 5426.0781250 5426.0781250
80 Percent Complete: Total/live time: 5440.0781250 5440.0781250
90 Percent Complete: Total/live time: 6112.0761719 6112.0761719
100 Percent Complete: Total/live time: 6112.0761719 6112.0761719
Number of attitude steps used: 16
Number of attitude steps avail: 7416
Mean RA/DEC pixel offset: -12.2912 -3.0394
writing expo file: ad12002220g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 93932 123 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
94055 93932 123 0 0 0
in 6112.08 seconds
Image has 93932 counts for 15.37 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 58394 123 0 0 35538
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
94055 58394 123 0 0 35538
in 6112.08 seconds
Image has 58394 counts for 9.554 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 36180 123 0 0 57752
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
94055 36180 123 0 0 57752
in 6112.08 seconds
Image has 36180 counts for 5.919 counts/sec
Command not found; type ? for a command listing
!ad12002220g200270m:ASCA >
!ad12002220g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g200270m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g200270m:ASCA > read events ad12002220g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g200270m:ASCA-GIS2-PH > set image sky
!ad12002220g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad12002220g200270m:ASCA-GIS2-PH > extract image
!ad12002220g200270m:ASCA-GIS2-PH > save image outfile=ad12002220g200270m.img
Wrote image to file ad12002220g200270m.img
!ad12002220g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad12002220g200270m:ASCA-GIS2-PH > extract image
!ad12002220g200270m:ASCA-GIS2-PH > save image outfile=ad12002220g200270m_lo.img
Wrote image to file ad12002220g200270m_lo.img
!ad12002220g200270m:ASCA-GIS2-PH > clear pha_cut
!ad12002220g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g200270m:ASCA-GIS2-PH > extract image
!ad12002220g200270m:ASCA-GIS2-PH > save image outfile=ad12002220g200270m_hi.img
Wrote image to file ad12002220g200270m_hi.img
!ad12002220g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad12002220g200370l.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4504
Mean RA/DEC/ROLL : 350.7267 58.9026 323.4504
Pnt RA/DEC/ROLL : 350.6713 58.9417 323.4504
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 12
Total GTI (secs) : 2335.895
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 525.9985962 525.9985962
20 Percent Complete: Total/live time: 525.9985962 525.9985962
30 Percent Complete: Total/live time: 1096.0037842 1096.0037842
40 Percent Complete: Total/live time: 1096.0037842 1096.0037842
50 Percent Complete: Total/live time: 1213.9896240 1213.9896240
60 Percent Complete: Total/live time: 1542.0137939 1542.0137939
70 Percent Complete: Total/live time: 1832.0065918 1832.0065918
80 Percent Complete: Total/live time: 2047.8846436 2047.8846436
90 Percent Complete: Total/live time: 2335.8950195 2335.8950195
100 Percent Complete: Total/live time: 2335.8950195 2335.8950195
Number of attitude steps used: 14
Number of attitude steps avail: 2142
Mean RA/DEC pixel offset: -11.8776 -3.0644
writing expo file: ad12002220g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g200370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g200370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 8908 4 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8912 8908 4 0 0 0
in 2335.90 seconds
Image has 8908 counts for 3.814 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 5562 4 0 0 3346
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8912 5562 4 0 0 3346
in 2335.90 seconds
Image has 5562 counts for 2.381 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 3404 4 0 0 5504
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8912 3404 4 0 0 5504
in 2335.90 seconds
Image has 3404 counts for 1.457 counts/sec
Command not found; type ? for a command listing
!ad12002220g200370l:ASCA >
!ad12002220g200370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g200370l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g200370l:ASCA > read events ad12002220g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g200370l:ASCA-GIS2-PH > set image sky
!ad12002220g200370l:ASCA-GIS2-PH > filter region corner_point.reg
!ad12002220g200370l:ASCA-GIS2-PH > extract image
!ad12002220g200370l:ASCA-GIS2-PH > save image outfile=ad12002220g200370l.img
Wrote image to file ad12002220g200370l.img
!ad12002220g200370l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad12002220g200370l:ASCA-GIS2-PH > extract image
!ad12002220g200370l:ASCA-GIS2-PH > save image outfile=ad12002220g200370l_lo.img
Wrote image to file ad12002220g200370l_lo.img
!ad12002220g200370l:ASCA-GIS2-PH > clear pha_cut
!ad12002220g200370l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g200370l:ASCA-GIS2-PH > extract image
!ad12002220g200370l:ASCA-GIS2-PH > save image outfile=ad12002220g200370l_hi.img
Wrote image to file ad12002220g200370l_hi.img
!ad12002220g200370l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad12002220g200470m.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g200470m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4529
Mean RA/DEC/ROLL : 350.7308 58.9017 323.4529
Pnt RA/DEC/ROLL : 350.6672 58.9433 323.4529
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 2
Total GTI (secs) : 32.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 16.0000000 16.0000000
20 Percent Complete: Total/live time: 16.0000000 16.0000000
30 Percent Complete: Total/live time: 17.9998951 17.9998951
40 Percent Complete: Total/live time: 17.9998951 17.9998951
50 Percent Complete: Total/live time: 32.0000000 32.0000000
100 Percent Complete: Total/live time: 32.0000000 32.0000000
Number of attitude steps used: 4
Number of attitude steps avail: 466
Mean RA/DEC pixel offset: -10.1818 -2.4847
writing expo file: ad12002220g200470m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g200470m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g200470m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 488 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
488 488 0 0 0 0
in 32.00 seconds
Image has 488 counts for 15.25 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 301 0 0 0 187
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
488 301 0 0 0 187
in 32.00 seconds
Image has 301 counts for 9.406 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 192 0 0 0 296
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
488 192 0 0 0 296
in 32.00 seconds
Image has 192 counts for 6.000 counts/sec
Command not found; type ? for a command listing
!ad12002220g200470m:ASCA >
!ad12002220g200470m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g200470m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g200470m:ASCA > read events ad12002220g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g200470m:ASCA-GIS2-PH > set image sky
!ad12002220g200470m:ASCA-GIS2-PH > filter region corner_point.reg
!ad12002220g200470m:ASCA-GIS2-PH > extract image
!ad12002220g200470m:ASCA-GIS2-PH > save image outfile=ad12002220g200470m.img
Wrote image to file ad12002220g200470m.img
!ad12002220g200470m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad12002220g200470m:ASCA-GIS2-PH > extract image
!ad12002220g200470m:ASCA-GIS2-PH > save image outfile=ad12002220g200470m_lo.img
Wrote image to file ad12002220g200470m_lo.img
!ad12002220g200470m:ASCA-GIS2-PH > clear pha_cut
!ad12002220g200470m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g200470m:ASCA-GIS2-PH > extract image
!ad12002220g200470m:ASCA-GIS2-PH > save image outfile=ad12002220g200470m_hi.img
Wrote image to file ad12002220g200470m_hi.img
!ad12002220g200470m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad12002220g200570l.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g200570l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4474
Mean RA/DEC/ROLL : 350.7262 58.9021 323.4474
Pnt RA/DEC/ROLL : 350.6716 58.9427 323.4474
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 1
Total GTI (secs) : 128.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 61.9998093 61.9998093
20 Percent Complete: Total/live time: 127.9997940 127.9997940
100 Percent Complete: Total/live time: 127.9997940 127.9997940
Number of attitude steps used: 2
Number of attitude steps avail: 11
Mean RA/DEC pixel offset: -6.2701 -1.8548
writing expo file: ad12002220g200570l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g200570l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g200570l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 489 1 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
490 489 1 0 0 0
in 128.00 seconds
Image has 489 counts for 3.820 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 286 1 0 0 203
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
490 286 1 0 0 203
in 128.00 seconds
Image has 286 counts for 2.234 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 206 1 0 0 283
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
490 206 1 0 0 283
in 128.00 seconds
Image has 206 counts for 1.609 counts/sec
Command not found; type ? for a command listing
!ad12002220g200570l:ASCA >
!ad12002220g200570l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g200570l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g200570l:ASCA > read events ad12002220g200570l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g200570l:ASCA-GIS2-PH > set image sky
!ad12002220g200570l:ASCA-GIS2-PH > filter region corner_point.reg
!ad12002220g200570l:ASCA-GIS2-PH > extract image
!ad12002220g200570l:ASCA-GIS2-PH > save image outfile=ad12002220g200570l.img
Wrote image to file ad12002220g200570l.img
!ad12002220g200570l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad12002220g200570l:ASCA-GIS2-PH > extract image
!ad12002220g200570l:ASCA-GIS2-PH > save image outfile=ad12002220g200570l_lo.img
Wrote image to file ad12002220g200570l_lo.img
!ad12002220g200570l:ASCA-GIS2-PH > clear pha_cut
!ad12002220g200570l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g200570l:ASCA-GIS2-PH > extract image
!ad12002220g200570l:ASCA-GIS2-PH > save image outfile=ad12002220g200570l_hi.img
Wrote image to file ad12002220g200570l_hi.img
!ad12002220g200570l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad12002220g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad12002220g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4207
Mean RA/DEC/ROLL : 350.6930 58.9188 323.4207
Pnt RA/DEC/ROLL : 350.7051 58.9245 323.4207
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 67
Total GTI (secs) : 20900.656
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3305.9882812 3305.9882812
20 Percent Complete: Total/live time: 4965.9824219 4965.9824219
30 Percent Complete: Total/live time: 6996.0898438 6996.0898438
40 Percent Complete: Total/live time: 8909.0878906 8909.0878906
50 Percent Complete: Total/live time: 10898.1650391 10898.1650391
60 Percent Complete: Total/live time: 13340.2587891 13340.2587891
70 Percent Complete: Total/live time: 14842.6210938 14842.6210938
80 Percent Complete: Total/live time: 17191.7792969 17191.7792969
90 Percent Complete: Total/live time: 19589.4570312 19589.4570312
100 Percent Complete: Total/live time: 20900.6542969 20900.6542969
Number of attitude steps used: 44
Number of attitude steps avail: 53970
Mean RA/DEC pixel offset: -0.8719 -2.0240
writing expo file: ad12002220g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 1007479 819 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008298 1007479 819 0 0 0
in 20900.66 seconds
Image has 1007479 counts for 48.20 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 624928 819 0 0 382551
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008298 624928 819 0 0 382551
in 20900.66 seconds
Image has 624928 counts for 29.90 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 389274 819 0 0 618205
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008298 389274 819 0 0 618205
in 20900.66 seconds
Image has 389274 counts for 18.62 counts/sec
Command not found; type ? for a command listing
!ad12002220g300170h:ASCA >
!ad12002220g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300170h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300170h:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300170h:ASCA-GIS3-PH > set image sky
!ad12002220g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300170h:ASCA-GIS3-PH > extract image
!ad12002220g300170h:ASCA-GIS3-PH > save image outfile=ad12002220g300170h.img
Wrote image to file ad12002220g300170h.img
!ad12002220g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300170h:ASCA-GIS3-PH > extract image
!ad12002220g300170h:ASCA-GIS3-PH > save image outfile=ad12002220g300170h_lo.img
Wrote image to file ad12002220g300170h_lo.img
!ad12002220g300170h:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300170h:ASCA-GIS3-PH > extract image
!ad12002220g300170h:ASCA-GIS3-PH > save image outfile=ad12002220g300170h_hi.img
Wrote image to file ad12002220g300170h_hi.img
!ad12002220g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4209
Mean RA/DEC/ROLL : 350.6942 58.9188 323.4209
Pnt RA/DEC/ROLL : 350.7052 58.9251 323.4209
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 5
Total GTI (secs) : 6112.076
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 697.9659424 697.9659424
20 Percent Complete: Total/live time: 1321.9638672 1321.9638672
30 Percent Complete: Total/live time: 1925.9620361 1925.9620361
40 Percent Complete: Total/live time: 3696.0832520 3696.0832520
50 Percent Complete: Total/live time: 3696.0832520 3696.0832520
60 Percent Complete: Total/live time: 5426.0781250 5426.0781250
70 Percent Complete: Total/live time: 5426.0781250 5426.0781250
80 Percent Complete: Total/live time: 5440.0781250 5440.0781250
90 Percent Complete: Total/live time: 6112.0761719 6112.0761719
100 Percent Complete: Total/live time: 6112.0761719 6112.0761719
Number of attitude steps used: 16
Number of attitude steps avail: 7416
Mean RA/DEC pixel offset: -0.9675 -1.9145
writing expo file: ad12002220g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 95777 77 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
95854 95777 77 0 0 0
in 6112.08 seconds
Image has 95777 counts for 15.67 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 59144 77 0 0 36633
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
95854 59144 77 0 0 36633
in 6112.08 seconds
Image has 59144 counts for 9.677 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 37243 77 0 0 58534
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
95854 37243 77 0 0 58534
in 6112.08 seconds
Image has 37243 counts for 6.093 counts/sec
Command not found; type ? for a command listing
!ad12002220g300270m:ASCA >
!ad12002220g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300270m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300270m:ASCA > read events ad12002220g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300270m:ASCA-GIS3-PH > set image sky
!ad12002220g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300270m:ASCA-GIS3-PH > extract image
!ad12002220g300270m:ASCA-GIS3-PH > save image outfile=ad12002220g300270m.img
Wrote image to file ad12002220g300270m.img
!ad12002220g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300270m:ASCA-GIS3-PH > extract image
!ad12002220g300270m:ASCA-GIS3-PH > save image outfile=ad12002220g300270m_lo.img
Wrote image to file ad12002220g300270m_lo.img
!ad12002220g300270m:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300270m:ASCA-GIS3-PH > extract image
!ad12002220g300270m:ASCA-GIS3-PH > save image outfile=ad12002220g300270m_hi.img
Wrote image to file ad12002220g300270m_hi.img
!ad12002220g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220g300370l.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4200
Mean RA/DEC/ROLL : 350.6911 58.9193 323.4200
Pnt RA/DEC/ROLL : 350.7069 58.9250 323.4200
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 12
Total GTI (secs) : 2335.895
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 525.9985962 525.9985962
20 Percent Complete: Total/live time: 525.9985962 525.9985962
30 Percent Complete: Total/live time: 1096.0037842 1096.0037842
40 Percent Complete: Total/live time: 1096.0037842 1096.0037842
50 Percent Complete: Total/live time: 1213.9896240 1213.9896240
60 Percent Complete: Total/live time: 1542.0137939 1542.0137939
70 Percent Complete: Total/live time: 1832.0065918 1832.0065918
80 Percent Complete: Total/live time: 2047.8846436 2047.8846436
90 Percent Complete: Total/live time: 2335.8950195 2335.8950195
100 Percent Complete: Total/live time: 2335.8950195 2335.8950195
Number of attitude steps used: 14
Number of attitude steps avail: 2142
Mean RA/DEC pixel offset: -0.6618 -1.9503
writing expo file: ad12002220g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 9089 5 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9094 9089 5 0 0 0
in 2335.90 seconds
Image has 9089 counts for 3.891 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 5608 5 0 0 3481
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9094 5608 5 0 0 3481
in 2335.90 seconds
Image has 5608 counts for 2.401 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 3532 5 0 0 5557
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9094 3532 5 0 0 5557
in 2335.90 seconds
Image has 3532 counts for 1.512 counts/sec
Command not found; type ? for a command listing
!ad12002220g300370l:ASCA >
!ad12002220g300370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300370l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300370l:ASCA > read events ad12002220g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300370l:ASCA-GIS3-PH > set image sky
!ad12002220g300370l:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300370l:ASCA-GIS3-PH > extract image
!ad12002220g300370l:ASCA-GIS3-PH > save image outfile=ad12002220g300370l.img
Wrote image to file ad12002220g300370l.img
!ad12002220g300370l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300370l:ASCA-GIS3-PH > extract image
!ad12002220g300370l:ASCA-GIS3-PH > save image outfile=ad12002220g300370l_lo.img
Wrote image to file ad12002220g300370l_lo.img
!ad12002220g300370l:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300370l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300370l:ASCA-GIS3-PH > extract image
!ad12002220g300370l:ASCA-GIS3-PH > save image outfile=ad12002220g300370l_hi.img
Wrote image to file ad12002220g300370l_hi.img
!ad12002220g300370l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220g300470h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g300470h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4236
Mean RA/DEC/ROLL : 350.6943 58.9186 323.4236
Pnt RA/DEC/ROLL : 350.7031 58.9262 323.4236
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 1
Total GTI (secs) : 12.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 11.9999685 11.9999685
100 Percent Complete: Total/live time: 11.9999685 11.9999685
Number of attitude steps used: 2
Number of attitude steps avail: 178
Mean RA/DEC pixel offset: -0.6817 -1.0556
writing expo file: ad12002220g300470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 589 1 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 589 1 0 0 0
in 12.00 seconds
Image has 589 counts for 49.08 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 358 1 0 0 231
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 358 1 0 0 231
in 12.00 seconds
Image has 358 counts for 29.83 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 236 1 0 0 353
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 236 1 0 0 353
in 12.00 seconds
Image has 236 counts for 19.67 counts/sec
Command not found; type ? for a command listing
!ad12002220g300470h:ASCA >
!ad12002220g300470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300470h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300470h:ASCA > read events ad12002220g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300470h:ASCA-GIS3-PH > set image sky
!ad12002220g300470h:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300470h:ASCA-GIS3-PH > extract image
!ad12002220g300470h:ASCA-GIS3-PH > save image outfile=ad12002220g300470h.img
Wrote image to file ad12002220g300470h.img
!ad12002220g300470h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300470h:ASCA-GIS3-PH > extract image
!ad12002220g300470h:ASCA-GIS3-PH > save image outfile=ad12002220g300470h_lo.img
Wrote image to file ad12002220g300470h_lo.img
!ad12002220g300470h:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300470h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300470h:ASCA-GIS3-PH > extract image
!ad12002220g300470h:ASCA-GIS3-PH > save image outfile=ad12002220g300470h_hi.img
Wrote image to file ad12002220g300470h_hi.img
!ad12002220g300470h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220g300570m.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g300570m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4224
Mean RA/DEC/ROLL : 350.6952 58.9184 323.4224
Pnt RA/DEC/ROLL : 350.7029 58.9266 323.4224
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 2
Total GTI (secs) : 32.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 16.0000000 16.0000000
20 Percent Complete: Total/live time: 16.0000000 16.0000000
30 Percent Complete: Total/live time: 17.9998951 17.9998951
40 Percent Complete: Total/live time: 17.9998951 17.9998951
50 Percent Complete: Total/live time: 32.0000000 32.0000000
100 Percent Complete: Total/live time: 32.0000000 32.0000000
Number of attitude steps used: 4
Number of attitude steps avail: 466
Mean RA/DEC pixel offset: -1.1228 -1.5848
writing expo file: ad12002220g300570m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300570m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300570m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 497 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
497 497 0 0 0 0
in 32.00 seconds
Image has 497 counts for 15.53 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 306 0 0 0 191
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
497 306 0 0 0 191
in 32.00 seconds
Image has 306 counts for 9.562 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 198 0 0 0 299
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
497 198 0 0 0 299
in 32.00 seconds
Image has 198 counts for 6.188 counts/sec
Command not found; type ? for a command listing
!ad12002220g300570m:ASCA >
!ad12002220g300570m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300570m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300570m:ASCA > read events ad12002220g300570m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300570m:ASCA-GIS3-PH > set image sky
!ad12002220g300570m:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300570m:ASCA-GIS3-PH > extract image
!ad12002220g300570m:ASCA-GIS3-PH > save image outfile=ad12002220g300570m.img
Wrote image to file ad12002220g300570m.img
!ad12002220g300570m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300570m:ASCA-GIS3-PH > extract image
!ad12002220g300570m:ASCA-GIS3-PH > save image outfile=ad12002220g300570m_lo.img
Wrote image to file ad12002220g300570m_lo.img
!ad12002220g300570m:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300570m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300570m:ASCA-GIS3-PH > extract image
!ad12002220g300570m:ASCA-GIS3-PH > save image outfile=ad12002220g300570m_hi.img
Wrote image to file ad12002220g300570m_hi.img
!ad12002220g300570m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220g300670l.expo
ASCAEXPO_V0.9b
reading data file: ad12002220g300670l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4169
Mean RA/DEC/ROLL : 350.6906 58.9188 323.4169
Pnt RA/DEC/ROLL : 350.7072 58.9260 323.4169
Image rebin factor : 1
Attitude Records : 63713
GTI intervals : 1
Total GTI (secs) : 128.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 61.9998093 61.9998093
20 Percent Complete: Total/live time: 127.9997940 127.9997940
100 Percent Complete: Total/live time: 127.9997940 127.9997940
Number of attitude steps used: 2
Number of attitude steps avail: 11
Mean RA/DEC pixel offset: -0.2308 -1.2548
writing expo file: ad12002220g300670l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220g300670l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220g300670l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 498 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
498 498 0 0 0 0
in 128.00 seconds
Image has 498 counts for 3.891 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 317 0 0 0 181
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
498 317 0 0 0 181
in 128.00 seconds
Image has 317 counts for 2.477 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 186 0 0 0 312
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
498 186 0 0 0 312
in 128.00 seconds
Image has 186 counts for 1.453 counts/sec
Command not found; type ? for a command listing
!ad12002220g300670l:ASCA >
!ad12002220g300670l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220g300670l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220g300670l:ASCA > read events ad12002220g300670l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220g300670l:ASCA-GIS3-PH > set image sky
!ad12002220g300670l:ASCA-GIS3-PH > filter region corner_point.reg
!ad12002220g300670l:ASCA-GIS3-PH > extract image
!ad12002220g300670l:ASCA-GIS3-PH > save image outfile=ad12002220g300670l.img
Wrote image to file ad12002220g300670l.img
!ad12002220g300670l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad12002220g300670l:ASCA-GIS3-PH > extract image
!ad12002220g300670l:ASCA-GIS3-PH > save image outfile=ad12002220g300670l_lo.img
Wrote image to file ad12002220g300670l_lo.img
!ad12002220g300670l:ASCA-GIS3-PH > clear pha_cut
!ad12002220g300670l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad12002220g300670l:ASCA-GIS3-PH > extract image
!ad12002220g300670l:ASCA-GIS3-PH > save image outfile=ad12002220g300670l_hi.img
Wrote image to file ad12002220g300670l_hi.img
!ad12002220g300670l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad12002220s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 96 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4207
Mean RA/DEC/ROLL : 350.6935 58.8982 323.4207
Pnt RA/DEC/ROLL : 350.7071 58.9457 323.4207
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 0
GTI intervals : 2
Total GTI (secs) : 21.969
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3.8636720 3.8636720
20 Percent Complete: Total/live time: 21.9687862 21.9687862
100 Percent Complete: Total/live time: 21.9687862 21.9687862
Number of attitude steps used: 4
Number of attitude steps avail: 214
Mean RA/DEC pixel offset: -52.5859 -62.5266
writing expo file: ad12002220s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 594 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 594 0 0 0 0
in 21.97 seconds
Image has 594 counts for 27.04 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 392 0 0 0 202
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 392 0 0 0 202
in 21.97 seconds
Image has 392 counts for 17.84 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 202 0 0 0 392
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 202 0 0 0 392
in 21.97 seconds
Image has 202 counts for 9.195 counts/sec
Command not found; type ? for a command listing
!ad12002220s000102h:ASCA >
!ad12002220s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s000102h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s000102h:ASCA > read events ad12002220s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad12002220s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad12002220s000102h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000102h.img
Wrote image to file ad12002220s000102h.img
!ad12002220s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad12002220s000102h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000102h_lo.img
Wrote image to file ad12002220s000102h_lo.img
!ad12002220s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad12002220s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s000102h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000102h_hi.img
Wrote image to file ad12002220s000102h_hi.img
!ad12002220s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 96 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4206
Mean RA/DEC/ROLL : 350.6926 58.8980 323.4206
Pnt RA/DEC/ROLL : 350.7071 58.9466 323.4206
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 31
GTI intervals : 18
Total GTI (secs) : 7556.075
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1584.0368652 1584.0368652
20 Percent Complete: Total/live time: 2099.4206543 2099.4206543
30 Percent Complete: Total/live time: 3463.9118652 3463.9118652
40 Percent Complete: Total/live time: 3463.9118652 3463.9118652
50 Percent Complete: Total/live time: 4167.9116211 4167.9116211
60 Percent Complete: Total/live time: 5155.2626953 5155.2626953
70 Percent Complete: Total/live time: 5442.2617188 5442.2617188
80 Percent Complete: Total/live time: 7556.0742188 7556.0742188
100 Percent Complete: Total/live time: 7556.0742188 7556.0742188
Number of attitude steps used: 16
Number of attitude steps avail: 18852
Mean RA/DEC pixel offset: -61.4777 -89.1406
writing expo file: ad12002220s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 179637 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
179637 179637 0 0 0 0
in 7556.07 seconds
Image has 179637 counts for 23.77 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 74440 0 0 0 105197
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
179637 74440 0 0 0 105197
in 7556.07 seconds
Image has 74440 counts for 9.852 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 105703 0 0 0 73934
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
179637 105703 0 0 0 73934
in 7556.07 seconds
Image has 105703 counts for 13.99 counts/sec
Command not found; type ? for a command listing
!ad12002220s000202h:ASCA >
!ad12002220s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s000202h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s000202h:ASCA > read events ad12002220s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad12002220s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad12002220s000202h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000202h.img
Wrote image to file ad12002220s000202h.img
!ad12002220s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad12002220s000202h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000202h_lo.img
Wrote image to file ad12002220s000202h_lo.img
!ad12002220s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad12002220s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s000202h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000202h_hi.img
Wrote image to file ad12002220s000202h_hi.img
!ad12002220s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s000302m.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s000302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 96 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4203
Mean RA/DEC/ROLL : 350.6942 58.8982 323.4203
Pnt RA/DEC/ROLL : 350.7055 58.9459 323.4203
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 17
GTI intervals : 3
Total GTI (secs) : 653.001
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 653.0009766 653.0009766
100 Percent Complete: Total/live time: 653.0009766 653.0009766
Number of attitude steps used: 4
Number of attitude steps avail: 168
Mean RA/DEC pixel offset: -49.4201 -69.7728
writing expo file: ad12002220s000302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s000302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s000302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 10060 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10060 10060 0 0 0 0
in 653.00 seconds
Image has 10060 counts for 15.41 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 4332 0 0 0 5728
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10060 4332 0 0 0 5728
in 653.00 seconds
Image has 4332 counts for 6.634 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 5759 0 0 0 4301
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10060 5759 0 0 0 4301
in 653.00 seconds
Image has 5759 counts for 8.819 counts/sec
Command not found; type ? for a command listing
!ad12002220s000302m:ASCA >
!ad12002220s000302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s000302m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s000302m:ASCA > read events ad12002220s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad12002220s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad12002220s000302m:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000302m.img
Wrote image to file ad12002220s000302m.img
!ad12002220s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad12002220s000302m:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000302m_lo.img
Wrote image to file ad12002220s000302m_lo.img
!ad12002220s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad12002220s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s000302m:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000302m_hi.img
Wrote image to file ad12002220s000302m_hi.img
!ad12002220s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s000702h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s000702h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 96 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4174
Mean RA/DEC/ROLL : 350.6905 58.8984 323.4174
Pnt RA/DEC/ROLL : 350.7070 58.9463 323.4174
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 4
GTI intervals : 2
Total GTI (secs) : 28.066
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 12.0242815 12.0242815
20 Percent Complete: Total/live time: 12.0242815 12.0242815
30 Percent Complete: Total/live time: 12.5242920 12.5242920
40 Percent Complete: Total/live time: 12.5242920 12.5242920
50 Percent Complete: Total/live time: 28.0663872 28.0663872
100 Percent Complete: Total/live time: 28.0663872 28.0663872
Number of attitude steps used: 4
Number of attitude steps avail: 308
Mean RA/DEC pixel offset: -45.1669 -72.0282
writing expo file: ad12002220s000702h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s000702h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s000702h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 536 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 536 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
536 536 0 0 0 0
in 28.07 seconds
Image has 536 counts for 19.10 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 179 0 0 0 357
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
536 179 0 0 0 357
in 28.07 seconds
Image has 179 counts for 6.378 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 359 0 0 0 177
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
536 359 0 0 0 177
in 28.07 seconds
Image has 359 counts for 12.79 counts/sec
Command not found; type ? for a command listing
!ad12002220s000702h:ASCA >
!ad12002220s000702h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s000702h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s000702h:ASCA > read events ad12002220s000702h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s000702h:ASCA-SIS0-BRIGHT > set image sky
!ad12002220s000702h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad12002220s000702h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000702h.img
Wrote image to file ad12002220s000702h.img
!ad12002220s000702h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad12002220s000702h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000702h_lo.img
Wrote image to file ad12002220s000702h_lo.img
!ad12002220s000702h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad12002220s000702h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s000702h:ASCA-SIS0-BRIGHT > extract image
!ad12002220s000702h:ASCA-SIS0-BRIGHT > save image outfile=ad12002220s000702h_hi.img
Wrote image to file ad12002220s000702h_hi.img
!ad12002220s000702h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s100202h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 132
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4376
Mean RA/DEC/ROLL : 350.7124 58.9102 323.4376
Pnt RA/DEC/ROLL : 350.6872 58.9344 323.4376
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 53
GTI intervals : 20
Total GTI (secs) : 7609.582
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1553.9636230 1553.9636230
20 Percent Complete: Total/live time: 2089.2849121 2089.2849121
30 Percent Complete: Total/live time: 3421.7761230 3421.7761230
40 Percent Complete: Total/live time: 3421.7761230 3421.7761230
50 Percent Complete: Total/live time: 4099.6127930 4099.6127930
60 Percent Complete: Total/live time: 5118.9638672 5118.9638672
70 Percent Complete: Total/live time: 5405.9628906 5405.9628906
80 Percent Complete: Total/live time: 7609.5810547 7609.5810547
100 Percent Complete: Total/live time: 7609.5810547 7609.5810547
Number of attitude steps used: 16
Number of attitude steps avail: 18852
Mean RA/DEC pixel offset: -65.6442 -21.7801
writing expo file: ad12002220s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s100202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s100202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 157771 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
157771 157771 0 0 0 0
in 7609.58 seconds
Image has 157771 counts for 20.73 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 67711 0 0 0 90060
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
157771 67711 0 0 0 90060
in 7609.58 seconds
Image has 67711 counts for 8.898 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 90441 0 0 0 67330
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
157771 90441 0 0 0 67330
in 7609.58 seconds
Image has 90441 counts for 11.89 counts/sec
Command not found; type ? for a command listing
!ad12002220s100202h:ASCA >
!ad12002220s100202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s100202h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s100202h:ASCA > read events ad12002220s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s100202h:ASCA-SIS1-BRIGHT > set image sky
!ad12002220s100202h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad12002220s100202h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100202h.img
Wrote image to file ad12002220s100202h.img
!ad12002220s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad12002220s100202h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100202h_lo.img
Wrote image to file ad12002220s100202h_lo.img
!ad12002220s100202h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad12002220s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s100202h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100202h_hi.img
Wrote image to file ad12002220s100202h_hi.img
!ad12002220s100202h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s100502l.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s100502l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 132
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4372
Mean RA/DEC/ROLL : 350.7125 58.9102 323.4372
Pnt RA/DEC/ROLL : 350.6876 58.9334 323.4372
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 2
GTI intervals : 2
Total GTI (secs) : 32.282
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 32.2819214 32.2819214
100 Percent Complete: Total/live time: 32.2819214 32.2819214
Number of attitude steps used: 2
Number of attitude steps avail: 3559
Mean RA/DEC pixel offset: -36.2987 -11.2664
writing expo file: ad12002220s100502l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s100502l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s100502l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 239 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
239 239 0 0 0 0
in 32.28 seconds
Image has 239 counts for 7.404 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 128 0 0 0 111
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
239 128 0 0 0 111
in 32.28 seconds
Image has 128 counts for 3.965 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 112 0 0 0 127
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
239 112 0 0 0 127
in 32.28 seconds
Image has 112 counts for 3.469 counts/sec
Command not found; type ? for a command listing
!ad12002220s100502l:ASCA >
!ad12002220s100502l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s100502l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s100502l:ASCA > read events ad12002220s100502l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s100502l:ASCA-SIS1-BRIGHT > set image sky
!ad12002220s100502l:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad12002220s100502l:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100502l:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100502l.img
Wrote image to file ad12002220s100502l.img
!ad12002220s100502l:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad12002220s100502l:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100502l:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100502l_lo.img
Wrote image to file ad12002220s100502l_lo.img
!ad12002220s100502l:ASCA-SIS1-BRIGHT > clear pha_cut
!ad12002220s100502l:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s100502l:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100502l:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100502l_hi.img
Wrote image to file ad12002220s100502l_hi.img
!ad12002220s100502l:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad12002220s100702h.expo
ASCAEXPO_V0.9b
reading data file: ad12002220s100702h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 132
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950802_0233.2030
making an exposure map...
Aspect RA/DEC/ROLL : 350.6950 58.9236 323.4344
Mean RA/DEC/ROLL : 350.7102 58.9106 323.4344
Pnt RA/DEC/ROLL : 350.6871 58.9342 323.4344
Image rebin factor : 4
Attitude Records : 63713
Hot Pixels : 7
GTI intervals : 2
Total GTI (secs) : 28.066
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 12.0242882 12.0242882
20 Percent Complete: Total/live time: 12.0242882 12.0242882
30 Percent Complete: Total/live time: 12.5243044 12.5243044
40 Percent Complete: Total/live time: 12.5243044 12.5243044
50 Percent Complete: Total/live time: 28.0664005 28.0664005
100 Percent Complete: Total/live time: 28.0664005 28.0664005
Number of attitude steps used: 4
Number of attitude steps avail: 308
Mean RA/DEC pixel offset: -48.5001 -18.1399
writing expo file: ad12002220s100702h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad12002220s100702h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad12002220s100702h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 866 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 866 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
866 866 0 0 0 0
in 28.07 seconds
Image has 866 counts for 30.86 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 401 0 0 0 465
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
866 401 0 0 0 465
in 28.07 seconds
Image has 401 counts for 14.29 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 465 0 0 0 401
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
866 465 0 0 0 401
in 28.07 seconds
Image has 465 counts for 16.57 counts/sec
Command not found; type ? for a command listing
!ad12002220s100702h:ASCA >
!ad12002220s100702h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad12002220s100702h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!ad12002220s100702h:ASCA > read events ad12002220s100702h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!ad12002220s100702h:ASCA-SIS1-BRIGHT > set image sky
!ad12002220s100702h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad12002220s100702h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100702h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100702h.img
Wrote image to file ad12002220s100702h.img
!ad12002220s100702h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad12002220s100702h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100702h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100702h_lo.img
Wrote image to file ad12002220s100702h_lo.img
!ad12002220s100702h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad12002220s100702h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad12002220s100702h:ASCA-SIS1-BRIGHT > extract image
!ad12002220s100702h:ASCA-SIS1-BRIGHT > save image outfile=ad12002220s100702h_hi.img
Wrote image to file ad12002220s100702h_hi.img
!ad12002220s100702h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad12002220s000102h.expo ad12002220s000202h.expo ad12002220s000302m.expo ad12002220s000702h.expo ad12002220s100202h.expo ad12002220s100502l.expo ad12002220s100702h.expo-> Summing the following images to produce ad12002220sis32002_all.totsky
ad12002220s000102h.img ad12002220s000202h.img ad12002220s000302m.img ad12002220s000702h.img ad12002220s100202h.img ad12002220s100502l.img ad12002220s100702h.img-> Summing the following images to produce ad12002220sis32002_lo.totsky
ad12002220s000102h_lo.img ad12002220s000202h_lo.img ad12002220s000302m_lo.img ad12002220s000702h_lo.img ad12002220s100202h_lo.img ad12002220s100502l_lo.img ad12002220s100702h_lo.img-> Summing the following images to produce ad12002220sis32002_hi.totsky
ad12002220s000102h_hi.img ad12002220s000202h_hi.img ad12002220s000302m_hi.img ad12002220s000702h_hi.img ad12002220s100202h_hi.img ad12002220s100502l_hi.img ad12002220s100702h_hi.img-> Running XIMAGE to create ad12002220sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad12002220sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 271.000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 271 min: 0 ![2]XIMAGE> read/exp_map ad12002220sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 265.484 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 265 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 5.00000 50 -1 i,inten,mm,pp 3 22.0000 22 0 i,inten,mm,pp 4 113.000 113 0 ![9]XIMAGE> exit-> Summing gis images
ad12002220g200170h.expo ad12002220g200270m.expo ad12002220g200370l.expo ad12002220g200470m.expo ad12002220g200570l.expo ad12002220g300170h.expo ad12002220g300270m.expo ad12002220g300370l.expo ad12002220g300470h.expo ad12002220g300570m.expo ad12002220g300670l.expo-> Summing the following images to produce ad12002220gis25670_all.totsky
ad12002220g200170h.img ad12002220g200270m.img ad12002220g200370l.img ad12002220g200470m.img ad12002220g200570l.img ad12002220g300170h.img ad12002220g300270m.img ad12002220g300370l.img ad12002220g300470h.img ad12002220g300570m.img ad12002220g300670l.img-> Summing the following images to produce ad12002220gis25670_lo.totsky
ad12002220g200170h_lo.img ad12002220g200270m_lo.img ad12002220g200370l_lo.img ad12002220g200470m_lo.img ad12002220g200570l_lo.img ad12002220g300170h_lo.img ad12002220g300270m_lo.img ad12002220g300370l_lo.img ad12002220g300470h_lo.img ad12002220g300570m_lo.img ad12002220g300670l_lo.img-> Summing the following images to produce ad12002220gis25670_hi.totsky
ad12002220g200170h_hi.img ad12002220g200270m_hi.img ad12002220g200370l_hi.img ad12002220g200470m_hi.img ad12002220g200570l_hi.img ad12002220g300170h_hi.img ad12002220g300270m_hi.img ad12002220g300370l_hi.img ad12002220g300470h_hi.img ad12002220g300570m_hi.img ad12002220g300670l_hi.img-> Running XIMAGE to create ad12002220gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad12002220gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 3808.00 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 3808 min: 0 ![2]XIMAGE> read/exp_map ad12002220gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 983.888 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 983 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 14.0000 14 0 i,inten,mm,pp 4 60.0000 60 0 ![9]XIMAGE> exit
106 107 0.0546792 46 15 2418.55 95 51 0.000635749 10 11 30.0629-> Smoothing ad12002220gis25670_hi.totsky with ad12002220gis25670.totexpo
107 107 0.0208978 124 15 1741.59-> Smoothing ad12002220gis25670_lo.totsky with ad12002220gis25670.totexpo
107 108 0.0343196 123 15 3255.38-> Determining extraction radii
106 107 24 T 95 51 10 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad12002220gis25670.src
113 113 0.0131207 203 33 507.538-> Smoothing ad12002220sis32002_hi.totsky with ad12002220sis32002.totexpo
114 114 0.00750551 202 35 717.455-> Smoothing ad12002220sis32002_lo.totsky with ad12002220sis32002.totexpo
113 113 0.00582444 203 33 423.961-> Determining extraction radii
113 113 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad12002220sis32002.src
The sum of the selected column is 33713.000 The mean of the selected column is 344.01020 The standard deviation of the selected column is 2.3219921 The minimum of selected column is 341.00000 The maximum of selected column is 349.00000 The number of points used in calculation is 98-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 54288.000 The mean of the selected column is 553.95918 The standard deviation of the selected column is 1.7345392 The minimum of selected column is 550.00000 The maximum of selected column is 558.00000 The number of points used in calculation is 98-> Converting (452.0,452.0,2.0) to s1 detector coordinates
The sum of the selected column is 32869.000 The mean of the selected column is 342.38542 The standard deviation of the selected column is 2.1539183 The minimum of selected column is 338.00000 The maximum of selected column is 347.00000 The number of points used in calculation is 96-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 56605.000 The mean of the selected column is 589.63542 The standard deviation of the selected column is 1.5635304 The minimum of selected column is 587.00000 The maximum of selected column is 594.00000 The number of points used in calculation is 96-> Converting (106.0,107.0,2.0) to g2 detector coordinates
The sum of the selected column is 1602536.0 The mean of the selected column is 90.867317 The standard deviation of the selected column is 1.1201564 The minimum of selected column is 88.000000 The maximum of selected column is 94.000000 The number of points used in calculation is 17636-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2175382.0 The mean of the selected column is 123.34895 The standard deviation of the selected column is 1.1107279 The minimum of selected column is 121.00000 The maximum of selected column is 126.00000 The number of points used in calculation is 17636-> Converting (95.0,51.0,2.0) to g2 detector coordinates
The sum of the selected column is 40884.000 The mean of the selected column is 54.079365 The standard deviation of the selected column is 2.6085032 The minimum of selected column is 48.000000 The maximum of selected column is 60.000000 The number of points used in calculation is 756-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 66595.000 The mean of the selected column is 88.088624 The standard deviation of the selected column is 3.8954996 The minimum of selected column is 79.000000 The maximum of selected column is 95.000000 The number of points used in calculation is 756-> Converting (106.0,107.0,2.0) to g3 detector coordinates
The sum of the selected column is 2827473.0 The mean of the selected column is 96.960770 The standard deviation of the selected column is 1.1208083 The minimum of selected column is 94.000000 The maximum of selected column is 100.00000 The number of points used in calculation is 29161-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3615210.0 The mean of the selected column is 123.97414 The standard deviation of the selected column is 1.1034070 The minimum of selected column is 121.00000 The maximum of selected column is 127.00000 The number of points used in calculation is 29161-> Converting (95.0,51.0,2.0) to g3 detector coordinates
The sum of the selected column is 5876.0000 The mean of the selected column is 54.915888 The standard deviation of the selected column is 1.1584106 The minimum of selected column is 53.000000 The maximum of selected column is 57.000000 The number of points used in calculation is 107-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9152.0000 The mean of the selected column is 85.532710 The standard deviation of the selected column is 1.0489686 The minimum of selected column is 84.000000 The maximum of selected column is 88.000000 The number of points used in calculation is 107
1 ad12002220s000202h.evt 190233 1 ad12002220s000302m.evt 190233 1 ad12002220s000702h.evt 190233 2 ad12002220s000102h.evt 594-> Fetching SIS0_NOTCHIP0.1
ad12002220s000202h.evt ad12002220s000302m.evt ad12002220s000702h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
2 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
2 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
3 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 536 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 148512 31125 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 8619 1441 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 437 99 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
190233 157568 32665 0 0 0
in 8237.14 seconds
Spectrum has 157568 counts for 19.13 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 8237.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.29980E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 148512 31125 0 0 0
Writing events file
148512 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 8619 1441 0 0 0
Writing events file
157131 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 437 99 0 0 0
Writing events file
157568 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
190233 157568 32665 0 0 0
in 8237.14 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad12002220s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad12002220s000702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad12002220s010102_1.pi group=yes
Wrote spectrum to ad12002220s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad12002220s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 8237.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.29980E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 52 are grouped by a factor 40 ... 53 - 212 are single channels ... 213 - 216 are grouped by a factor 2 ... 217 - 235 are single channels ... 236 - 243 are grouped by a factor 2 ... 244 - 249 are grouped by a factor 3 ... 250 - 253 are grouped by a factor 4 ... 254 - 268 are grouped by a factor 5 ... 269 - 274 are grouped by a factor 6 ... 275 - 294 are grouped by a factor 10 ... 295 - 307 are grouped by a factor 13 ... 308 - 342 are grouped by a factor 35 ... 343 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad12002220s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 36 by 29 bins
expanded to 36 by 29 bins
First WMAP bin is at detector pixel 224 400
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 38.024 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.57514E+05
Weighted mean angle from optical axis = 9.001 arcmin
-> SIS0_OFFCHIP.1 already present in current directoryad12002220s000102h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 210 384 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 210 384 0 0 0
in 21.97 seconds
Spectrum has 210 counts for 9.559 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 21.969 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.87598E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s010202_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 210 384 0 0 0
Writing events file
210 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 210 384 0 0 0
in 21.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad12002220s010202_1.pi group=yes
Wrote spectrum to ad12002220s010202_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s010202_1.pi since it has 210 events1 ad12002220s000212h.evt 181215 2 ad12002220s000112h.evt 635-> SIS0_NOTCHIP0.1 already present in current directory
ad12002220s000212h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.76E+04 181215 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000212h.evt
Total Good Bad: Region Time Phase Cut
181215 149758 31457 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
181215 149758 31457 0 0 0
in 7556.07 seconds
Spectrum has 149758 counts for 19.82 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7556.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.29980E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s010312_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000212h.evt
Total Good Bad: Region Time Phase Cut
181215 149758 31457 0 0 0
Writing events file
149758 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
181215 149758 31457 0 0 0
in 7556.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad12002220s010312_1.pi group=yes
Wrote spectrum to ad12002220s010312_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad12002220s010312_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7556.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.29980E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 105 are grouped by a factor 80 ... 106 - 361 are single channels ... 362 - 363 are grouped by a factor 2 ... 364 - 373 are single channels ... 374 - 379 are grouped by a factor 2 ... 380 - 380 are single channels ... 381 - 382 are grouped by a factor 2 ... 383 - 389 are single channels ... 390 - 417 are grouped by a factor 2 ... 418 - 420 are grouped by a factor 3 ... 421 - 450 are grouped by a factor 2 ... 451 - 453 are single channels ... 454 - 455 are grouped by a factor 2 ... 456 - 456 are single channels ... 457 - 458 are grouped by a factor 2 ... 459 - 460 are single channels ... 461 - 468 are grouped by a factor 2 ... 469 - 471 are grouped by a factor 3 ... 472 - 479 are grouped by a factor 4 ... 480 - 484 are grouped by a factor 5 ... 485 - 488 are grouped by a factor 4 ... 489 - 493 are grouped by a factor 5 ... 494 - 509 are grouped by a factor 8 ... 510 - 516 are grouped by a factor 7 ... 517 - 525 are grouped by a factor 9 ... 526 - 533 are grouped by a factor 8 ... 534 - 544 are grouped by a factor 11 ... 545 - 559 are grouped by a factor 15 ... 560 - 579 are grouped by a factor 20 ... 580 - 595 are grouped by a factor 16 ... 596 - 622 are grouped by a factor 27 ... 623 - 681 are grouped by a factor 59 ... 682 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220s010312_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad12002220s010312_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 36 by 29 bins
expanded to 36 by 29 bins
First WMAP bin is at detector pixel 224 400
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 38.024 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.49704E+05
Weighted mean angle from optical axis = 8.956 arcmin
-> SIS0_OFFCHIP.1 already present in current directoryad12002220s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.22E+02 635 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000112h.evt
Total Good Bad: Region Time Phase Cut
635 223 412 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
635 223 412 0 0 0
in 21.97 seconds
Spectrum has 223 counts for 10.15 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 21.969 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.87598E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s010412_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000112h.evt
Total Good Bad: Region Time Phase Cut
635 223 412 0 0 0
Writing events file
223 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
635 223 412 0 0 0
in 21.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad12002220s010412_1.pi group=yes
Wrote spectrum to ad12002220s010412_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s010412_1.pi since it has 223 events1 ad12002220s100202h.evt 158876 1 ad12002220s100502l.evt 158876 1 ad12002220s100702h.evt 158876-> Fetching SIS1_NOTCHIP1.1
ad12002220s100202h.evt ad12002220s100502l.evt ad12002220s100702h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
2 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
2 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
3 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 866 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 128859 28912 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 145 94 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 651 215 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158876 129655 29221 0 0 0
in 7669.93 seconds
Spectrum has 129655 counts for 16.90 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7669.9 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.70410E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 128859 28912 0 0 0
Writing events file
128859 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 145 94 0 0 0
Writing events file
129004 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 651 215 0 0 0
Writing events file
129655 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158876 129655 29221 0 0 0
in 7669.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad12002220s100502l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad12002220s100702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad12002220s110102_1.pi group=yes
Wrote spectrum to ad12002220s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad12002220s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7669.9 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.70410E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 52 are grouped by a factor 40 ... 53 - 199 are single channels ... 200 - 201 are grouped by a factor 2 ... 202 - 210 are single channels ... 211 - 212 are grouped by a factor 2 ... 213 - 214 are single channels ... 215 - 216 are grouped by a factor 2 ... 217 - 218 are single channels ... 219 - 220 are grouped by a factor 2 ... 221 - 231 are single channels ... 232 - 239 are grouped by a factor 2 ... 240 - 245 are grouped by a factor 3 ... 246 - 261 are grouped by a factor 4 ... 262 - 266 are grouped by a factor 5 ... 267 - 270 are grouped by a factor 4 ... 271 - 276 are grouped by a factor 6 ... 277 - 285 are grouped by a factor 9 ... 286 - 300 are grouped by a factor 15 ... 301 - 321 are grouped by a factor 21 ... 322 - 391 are grouped by a factor 70 ... 392 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad12002220s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 35 by 24 bins
expanded to 35 by 24 bins
First WMAP bin is at detector pixel 224 440
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 31.159 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.29607E+05
Weighted mean angle from optical axis = 9.692 arcmin
-> Standard Output From STOOL group_event_files:1 ad12002220s100212h.evt 158939-> SIS1_NOTCHIP1.1 already present in current directory
ad12002220s100212h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.76E+04 158939 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100212h.evt
Total Good Bad: Region Time Phase Cut
158939 129804 29135 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158939 129804 29135 0 0 0
in 7609.58 seconds
Spectrum has 129804 counts for 17.06 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7609.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.70410E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220s110212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100212h.evt
Total Good Bad: Region Time Phase Cut
158939 129804 29135 0 0 0
Writing events file
129804 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158939 129804 29135 0 0 0
in 7609.58 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100212h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad12002220s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad12002220s110212_1.pi group=yes
Wrote spectrum to ad12002220s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad12002220s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7609.6 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.70410E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 104 are grouped by a factor 79 ... 105 - 347 are single channels ... 348 - 349 are grouped by a factor 2 ... 350 - 353 are single channels ... 354 - 355 are grouped by a factor 2 ... 356 - 362 are single channels ... 363 - 366 are grouped by a factor 2 ... 367 - 367 are single channels ... 368 - 369 are grouped by a factor 2 ... 370 - 372 are single channels ... 373 - 382 are grouped by a factor 2 ... 383 - 383 are single channels ... 384 - 421 are grouped by a factor 2 ... 422 - 424 are grouped by a factor 3 ... 425 - 432 are grouped by a factor 2 ... 433 - 435 are grouped by a factor 3 ... 436 - 445 are grouped by a factor 2 ... 446 - 447 are single channels ... 448 - 453 are grouped by a factor 2 ... 454 - 454 are single channels ... 455 - 458 are grouped by a factor 2 ... 459 - 459 are single channels ... 460 - 465 are grouped by a factor 2 ... 466 - 468 are grouped by a factor 3 ... 469 - 480 are grouped by a factor 4 ... 481 - 498 are grouped by a factor 6 ... 499 - 512 are grouped by a factor 7 ... 513 - 522 are grouped by a factor 10 ... 523 - 531 are grouped by a factor 9 ... 532 - 539 are grouped by a factor 8 ... 540 - 550 are grouped by a factor 11 ... 551 - 564 are grouped by a factor 14 ... 565 - 587 are grouped by a factor 23 ... 588 - 631 are grouped by a factor 44 ... 632 - 693 are grouped by a factor 62 ... 694 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad12002220s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 35 by 24 bins
expanded to 35 by 24 bins
First WMAP bin is at detector pixel 224 440
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 31.159 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.29756E+05
Weighted mean angle from optical axis = 9.691 arcmin
-> Standard Output From STOOL group_event_files:1 ad12002220g200170h.evt 836511 1 ad12002220g200270m.evt 836511 1 ad12002220g200370l.evt 836511 1 ad12002220g200470m.evt 836511 1 ad12002220g200570l.evt 836511-> GIS2_REGION256.4 already present in current directory
ad12002220g200170h.evt ad12002220g200270m.evt ad12002220g200370l.evt ad12002220g200470m.evt ad12002220g200570l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
5 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 603641 128925 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 77636 16419 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 7370 1542 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 408 80 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 414 76 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
836511 689469 147042 0 0 0
in 29512.63 seconds
Spectrum has 689469 counts for 23.36 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29513. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad12002220g210170_1.pi group=yes
Wrote spectrum to ad12002220g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad12002220g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad12002220g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29513. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 18 are grouped by a factor 19 ... 19 - 593 are single channels ... 594 - 605 are grouped by a factor 2 ... 606 - 611 are grouped by a factor 3 ... 612 - 621 are grouped by a factor 2 ... 622 - 624 are grouped by a factor 3 ... 625 - 636 are grouped by a factor 2 ... 637 - 642 are grouped by a factor 3 ... 643 - 644 are grouped by a factor 2 ... 645 - 677 are grouped by a factor 3 ... 678 - 681 are grouped by a factor 4 ... 682 - 684 are grouped by a factor 3 ... 685 - 704 are grouped by a factor 4 ... 705 - 714 are grouped by a factor 5 ... 715 - 721 are grouped by a factor 7 ... 722 - 725 are grouped by a factor 4 ... 726 - 739 are grouped by a factor 7 ... 740 - 745 are grouped by a factor 6 ... 746 - 761 are grouped by a factor 8 ... 762 - 771 are grouped by a factor 10 ... 772 - 779 are grouped by a factor 8 ... 780 - 793 are grouped by a factor 14 ... 794 - 809 are grouped by a factor 16 ... 810 - 823 are grouped by a factor 14 ... 824 - 838 are grouped by a factor 15 ... 839 - 865 are grouped by a factor 27 ... 866 - 893 are grouped by a factor 28 ... 894 - 923 are grouped by a factor 30 ... 924 - 977 are grouped by a factor 54 ... 978 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 29 61
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.89469E+05
Weighted mean angle from optical axis = 10.808 arcmin
-> Extracting ad12002220g210170_2.pi from ad12002220g225670_2.reg and:ad12002220g200170h.evt ad12002220g200270m.evt ad12002220g200370l.evt ad12002220g200470m.evt ad12002220g200570l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
5 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 1942 730624 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 244 93811 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 15 8897 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 1 487 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 1 489 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
836511 2203 834308 0 0 0
in 29512.63 seconds
Spectrum has 2203 counts for 7.4646E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29513. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.90625E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g210170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad12002220g210170_2.pi group=yes
Wrote spectrum to ad12002220g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad12002220g210170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad12002220g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29513. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.90625E-03 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 48 are grouped by a factor 49 ... 49 - 69 are grouped by a factor 21 ... 70 - 78 are grouped by a factor 9 ... 79 - 84 are grouped by a factor 6 ... 85 - 109 are grouped by a factor 5 ... 110 - 137 are grouped by a factor 4 ... 138 - 149 are grouped by a factor 3 ... 150 - 153 are grouped by a factor 2 ... 154 - 156 are grouped by a factor 3 ... 157 - 164 are grouped by a factor 2 ... 165 - 167 are grouped by a factor 3 ... 168 - 179 are grouped by a factor 4 ... 180 - 184 are grouped by a factor 5 ... 185 - 192 are grouped by a factor 8 ... 193 - 198 are grouped by a factor 6 ... 199 - 208 are grouped by a factor 5 ... 209 - 220 are grouped by a factor 6 ... 221 - 248 are grouped by a factor 14 ... 249 - 259 are grouped by a factor 11 ... 260 - 280 are grouped by a factor 21 ... 281 - 308 are grouped by a factor 28 ... 309 - 335 are grouped by a factor 27 ... 336 - 367 are grouped by a factor 32 ... 368 - 424 are grouped by a factor 57 ... 425 - 518 are grouped by a factor 94 ... 519 - 659 are grouped by a factor 141 ... 660 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220g210170_2.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 18 by 21 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 25 58
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 15.439 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.20300E+03
Weighted mean angle from optical axis = 21.470 arcmin
-> Standard Output From STOOL group_event_files:1 ad12002220g300170h.evt 1114831 1 ad12002220g300270m.evt 1114831 1 ad12002220g300370l.evt 1114831 1 ad12002220g300470h.evt 1114831 1 ad12002220g300570m.evt 1114831 1 ad12002220g300670l.evt 1114831-> GIS3_REGION256.4 already present in current directory
ad12002220g300170h.evt ad12002220g300270m.evt ad12002220g300370l.evt ad12002220g300470h.evt ad12002220g300570m.evt ad12002220g300670l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
6 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 871425 136873 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 82913 12941 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 7842 1252 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 513 77 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 410 87 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 439 59 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1114831 963542 151289 0 0 0
in 29520.63 seconds
Spectrum has 963542 counts for 32.64 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29521. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300570m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300670l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad12002220g310170_1.pi group=yes
Wrote spectrum to ad12002220g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad12002220g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad12002220g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29521. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 19 are grouped by a factor 20 ... 20 - 598 are single channels ... 599 - 602 are grouped by a factor 2 ... 603 - 606 are single channels ... 607 - 614 are grouped by a factor 2 ... 615 - 615 are single channels ... 616 - 617 are grouped by a factor 2 ... 618 - 618 are single channels ... 619 - 630 are grouped by a factor 2 ... 631 - 631 are single channels ... 632 - 637 are grouped by a factor 2 ... 638 - 638 are single channels ... 639 - 658 are grouped by a factor 2 ... 659 - 661 are grouped by a factor 3 ... 662 - 662 are single channels ... 663 - 688 are grouped by a factor 2 ... 689 - 697 are grouped by a factor 3 ... 698 - 701 are grouped by a factor 4 ... 702 - 704 are grouped by a factor 3 ... 705 - 712 are grouped by a factor 4 ... 713 - 715 are grouped by a factor 3 ... 716 - 723 are grouped by a factor 4 ... 724 - 726 are grouped by a factor 3 ... 727 - 738 are grouped by a factor 4 ... 739 - 741 are grouped by a factor 3 ... 742 - 749 are grouped by a factor 4 ... 750 - 754 are grouped by a factor 5 ... 755 - 760 are grouped by a factor 6 ... 761 - 764 are grouped by a factor 4 ... 765 - 774 are grouped by a factor 5 ... 775 - 788 are grouped by a factor 7 ... 789 - 796 are grouped by a factor 8 ... 797 - 803 are grouped by a factor 7 ... 804 - 821 are grouped by a factor 9 ... 822 - 826 are grouped by a factor 5 ... 827 - 835 are grouped by a factor 9 ... 836 - 845 are grouped by a factor 10 ... 846 - 854 are grouped by a factor 9 ... 855 - 872 are grouped by a factor 18 ... 873 - 886 are grouped by a factor 14 ... 887 - 904 are grouped by a factor 18 ... 905 - 920 are grouped by a factor 16 ... 921 - 949 are grouped by a factor 29 ... 950 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 35 62
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.63542E+05
Weighted mean angle from optical axis = 6.668 arcmin
-> Extracting ad12002220g310170_2.pi from ad12002220g325670_2.reg and:ad12002220g300170h.evt ad12002220g300270m.evt ad12002220g300370l.evt ad12002220g300470h.evt ad12002220g300570m.evt ad12002220g300670l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
6 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 1719 1006579 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 169 95685 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 14 9080 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 1 589 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 0 497 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 0 498 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1114831 1903 1112928 0 0 0
in 29520.63 seconds
Spectrum has 1903 counts for 6.4463E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29521. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.86047E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g310170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300570m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300670l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad12002220g310170_2.pi group=yes
Wrote spectrum to ad12002220g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad12002220g310170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad12002220g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29521. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.86047E-03 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 47 are grouped by a factor 48 ... 48 - 68 are grouped by a factor 21 ... 69 - 79 are grouped by a factor 11 ... 80 - 86 are grouped by a factor 7 ... 87 - 92 are grouped by a factor 6 ... 93 - 96 are grouped by a factor 4 ... 97 - 108 are grouped by a factor 6 ... 109 - 113 are grouped by a factor 5 ... 114 - 121 are grouped by a factor 4 ... 122 - 126 are grouped by a factor 5 ... 127 - 134 are grouped by a factor 4 ... 135 - 140 are grouped by a factor 6 ... 141 - 148 are grouped by a factor 4 ... 149 - 160 are grouped by a factor 3 ... 161 - 162 are grouped by a factor 2 ... 163 - 165 are grouped by a factor 3 ... 166 - 173 are grouped by a factor 4 ... 174 - 188 are grouped by a factor 5 ... 189 - 194 are grouped by a factor 6 ... 195 - 201 are grouped by a factor 7 ... 202 - 206 are grouped by a factor 5 ... 207 - 213 are grouped by a factor 7 ... 214 - 218 are grouped by a factor 5 ... 219 - 238 are grouped by a factor 10 ... 239 - 256 are grouped by a factor 18 ... 257 - 269 are grouped by a factor 13 ... 270 - 292 are grouped by a factor 23 ... 293 - 319 are grouped by a factor 27 ... 320 - 347 are grouped by a factor 28 ... 348 - 402 are grouped by a factor 55 ... 403 - 576 are grouped by a factor 87 ... 577 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad12002220g310170_2.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 18 by 21 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 26 56
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 15.258 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.90300E+03
Weighted mean angle from optical axis = 19.261 arcmin
-> Plotting ad12002220g210170_1_pi.ps from ad12002220g210170_1.pi
XSPEC 9.01 13:16:23 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220g210170_1.pi
Net count rate (cts/s) for file 1 23.36 +/- 2.8136E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220g210170_2_pi.ps from ad12002220g210170_2.pi
XSPEC 9.01 13:16:37 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220g210170_2.pi
Net count rate (cts/s) for file 1 7.4646E-02+/- 1.7107E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220g310170_1_pi.ps from ad12002220g310170_1.pi
XSPEC 9.01 13:16:49 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220g310170_1.pi
Net count rate (cts/s) for file 1 32.64 +/- 3.3253E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220g310170_2_pi.ps from ad12002220g310170_2.pi
XSPEC 9.01 13:17:00 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220g310170_2.pi
Net count rate (cts/s) for file 1 6.4463E-02+/- 1.6341E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220s010102_1_pi.ps from ad12002220s010102_1.pi
XSPEC 9.01 13:17:12 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220s010102_1.pi
Net count rate (cts/s) for file 1 19.13 +/- 4.8216E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220s010312_1_pi.ps from ad12002220s010312_1.pi
XSPEC 9.01 13:17:25 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220s010312_1.pi
Net count rate (cts/s) for file 1 19.82 +/- 5.1273E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220s110102_1_pi.ps from ad12002220s110102_1.pi
XSPEC 9.01 13:17:39 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220s110102_1.pi
Net count rate (cts/s) for file 1 16.90 +/- 4.6970E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad12002220s110212_1_pi.ps from ad12002220s110212_1.pi
XSPEC 9.01 13:17:53 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad12002220s110212_1.pi
Net count rate (cts/s) for file 1 17.06 +/- 4.7407E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
2 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
2 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
3 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
2 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
3 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
4 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 536 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 220 374 0 0 0
Writing events file
220 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 151846 27791 0 0 0
Writing events file
152066 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 8846 1214 0 0 0
Writing events file
160912 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 450 86 0 0 0
Writing events file
161362 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
190827 161362 29465 0 0 0
in 8259.11 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad12002220s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad12002220s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad12002220s000702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad12002220s000002_1.lc with binsize 1.6000000000E+01
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.83E+04 161362 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
161362 161362 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
161362 161362 0 0 0 0
in 8259.11 seconds
Fits light curve has 161362 counts for 19.54 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > set binsize 1.6000000000E+01
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad12002220s000002_1.lc
Wrote FITS light curve to file ad12002220s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad12002220s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 04:42:57.655
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 17:29:01.680
No. of Rows ....... 517 Bin Time (s) ...... 16.00
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 89.8788 (s)
Intv 1 Start 9931 4:43:42
Ser.1 Avg 19.18 Chisq 1284. Var 6.926 Newbs. 106
Min 2.079 Max 24.13 expVar 0.3222 Bins 517
Results from Statistical Analysis
Newbin Integration Time (s).. 89.879
Interval Duration (s)........ 45928.
No. of Newbins .............. 106
Average (c/s) ............... 19.180 +/- 0.55E-01
Standard Deviation (c/s)..... 2.6318
Minimum (c/s)................ 2.0791
Maximum (c/s)................ 24.131
Variance ((c/s)**2).......... 6.9264 +/- 0.96
Expected Variance ((c/s)**2). 0.32224 +/- 0.44E-01
Third Moment ((c/s)**3)...... -60.071
Average Deviation (c/s)...... 1.6039
Skewness..................... -3.2954 +/- 0.24
Kurtosis..................... 15.764 +/- 0.48
RMS fractional variation..... 0.13399 +/- 0.97E-02
Chi-Square................... 1283.7 dof 105
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 89.8788 (s)
Intv 1 Start 9931 4:43:42
Ser.1 Avg 19.18 Chisq 1284. Var 6.926 Newbs. 106
Min 2.079 Max 24.13 expVar 0.3222 Bins 517
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=8.0000000000E+00 for ad12002220s100202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
2 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
2 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
3 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 866 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 133633 24138 0 0 0
Writing events file
133633 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 166 73 0 0 0
Writing events file
133799 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 667 199 0 0 0
Writing events file
134466 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158876 134466 24410 0 0 0
in 7669.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad12002220s100502l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad12002220s100702h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad12002220s100002_1.lc with binsize 8.0000000000E+00
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.77E+04 134466 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
134466 134466 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
134466 134466 0 0 0 0
in 7669.93 seconds
Fits light curve has 134466 counts for 17.53 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > set binsize 8.0000000000E+00
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad12002220s100002_1.lc
Wrote FITS light curve to file ad12002220s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad12002220s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 04:42:57.655
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 17:29:01.680
No. of Rows ....... 965 Bin Time (s) ...... 8.000
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 89.8788 (s)
Intv 1 Start 9931 4:43:42
Ser.1 Avg 18.02 Chisq 483.2 Var 3.296 Newbs. 96
Min 11.71 Max 27.65 expVar 0.2982 Bins 965
Results from Statistical Analysis
Newbin Integration Time (s).. 89.879
Interval Duration (s)........ 45928.
No. of Newbins .............. 96
Average (c/s) ............... 18.017 +/- 0.56E-01
Standard Deviation (c/s)..... 1.8155
Minimum (c/s)................ 11.714
Maximum (c/s)................ 27.654
Variance ((c/s)**2).......... 3.2962 +/- 0.48
Expected Variance ((c/s)**2). 0.29818 +/- 0.43E-01
Third Moment ((c/s)**3)...... 12.329
Average Deviation (c/s)...... 1.0605
Skewness..................... 2.0602 +/- 0.25
Kurtosis..................... 9.8083 +/- 0.50
RMS fractional variation..... 0.96099E-01 +/- 0.77E-02
Chi-Square................... 483.24 dof 95
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.47895E-06 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 89.8788 (s)
Intv 1 Start 9931 4:43:42
Ser.1 Avg 18.02 Chisq 483.2 Var 3.296 Newbs. 96
Min 11.71 Max 27.65 expVar 0.2982 Bins 965
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=6.2500000000E-02 for ad12002220g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
5 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 603641 128925 0 0 0
Writing events file
603641 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 77636 16419 0 0 0
Writing events file
681277 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 7370 1542 0 0 0
Writing events file
688647 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 408 80 0 0 0
Writing events file
689055 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 414 76 0 0 0
Writing events file
689469 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
836511 689469 147042 0 0 0
in 29512.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad12002220g200070_1.lc with binsize 2.14024314063803
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.30E+05 689469 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
689469 689469 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
689469 689469 0 0 0 0
in 29512.63 seconds
Fits light curve has 689469 counts for 23.36 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > set binsize 2.14024314063803
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad12002220g200070_1.lc
Wrote FITS light curve to file ad12002220g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad12002220g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 02:34:59.680
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 20:30:21.680
No. of Rows ....... 13786 Bin Time (s) ...... 2.140
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 126.167 (s)
Intv 1 Start 9931 2:36: 2
Ser.1 Avg 23.30 Chisq 0.5629E+05 Var 79.32 Newbs. 271
Min 2.160 Max 32.23 expVar 0.3924 Bins 13786
Results from Statistical Analysis
Newbin Integration Time (s).. 126.17
Interval Duration (s)........ 64472.
No. of Newbins .............. 271
Average (c/s) ............... 23.297 +/- 0.38E-01
Standard Deviation (c/s)..... 8.9064
Minimum (c/s)................ 2.1604
Maximum (c/s)................ 32.232
Variance ((c/s)**2).......... 79.323 +/- 6.8
Expected Variance ((c/s)**2). 0.39239 +/- 0.34E-01
Third Moment ((c/s)**3)...... -803.09
Average Deviation (c/s)...... 7.7924
Skewness..................... -1.1367 +/- 0.15
Kurtosis.....................-0.27830 +/- 0.30
RMS fractional variation..... 0.38135 +/- 0.16E-01
Chi-Square................... 56289. dof 270
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 126.167 (s)
Intv 1 Start 9931 2:36: 2
Ser.1 Avg 23.30 Chisq 0.5629E+05 Var 79.32 Newbs. 271
Min 2.160 Max 32.23 expVar 0.3924 Bins 13786
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> Extracting events from region ad12002220g225670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
5 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 1942 730624 0 0 0
Writing events file
1942 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 244 93811 0 0 0
Writing events file
2186 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 15 8897 0 0 0
Writing events file
2201 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 1 487 0 0 0
Writing events file
2202 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 1 489 0 0 0
Writing events file
2203 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
836511 2203 834308 0 0 0
in 29512.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200570l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad12002220g200070_2.lc with binsize 669.828097109653
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.30E+05 2203 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
2203 2203 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2203 2203 0 0 0 0
in 29512.63 seconds
Fits light curve has 2203 counts for 7.4646E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > set binsize 669.828097109653
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad12002220g200070_2.lc
Wrote FITS light curve to file ad12002220g200070_2.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad12002220g200070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 02:34:59.680
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 20:30:21.680
No. of Rows ....... 41 Bin Time (s) ...... 669.8
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 97 Newbins of 669.828 (s)
Intv 1 Start 9931 2:40:34
Ser.1 Avg 0.7731E-01 Chisq 218.8 Var 0.7224E-03 Newbs. 41
Min 0.2986E-02 Max 0.1232 expVar 0.1354E-03 Bins 41
Results from Statistical Analysis
Newbin Integration Time (s).. 669.83
Interval Duration (s)........ 63634.
No. of Newbins .............. 41
Average (c/s) ............... 0.77311E-01 +/- 0.18E-02
Standard Deviation (c/s)..... 0.26878E-01
Minimum (c/s)................ 0.29858E-02
Maximum (c/s)................ 0.12323
Variance ((c/s)**2).......... 0.72245E-03 +/- 0.16E-03
Expected Variance ((c/s)**2). 0.13536E-03 +/- 0.30E-04
Third Moment ((c/s)**3)......-0.12426E-04
Average Deviation (c/s)...... 0.22551E-01
Skewness.....................-0.63994 +/- 0.38
Kurtosis.....................-0.22751 +/- 0.77
RMS fractional variation..... 0.31341 +/- 0.43E-01
Chi-Square................... 218.82 dof 40
Chi-Square Prob of constancy. 0.16677E-25 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.65333E-07 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 97 Newbins of 669.828 (s)
Intv 1 Start 9931 2:40:34
Ser.1 Avg 0.7731E-01 Chisq 218.8 Var 0.7224E-03 Newbs. 41
Min 0.2986E-02 Max 0.1232 expVar 0.1354E-03 Bins 41
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad12002220g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
6 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 871425 136873 0 0 0
Writing events file
871425 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 82913 12941 0 0 0
Writing events file
954338 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 7842 1252 0 0 0
Writing events file
962180 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 513 77 0 0 0
Writing events file
962693 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 410 87 0 0 0
Writing events file
963103 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 439 59 0 0 0
Writing events file
963542 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1114831 963542 151289 0 0 0
in 29520.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300570m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300670l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad12002220g300070_1.lc with binsize 2.0000000000E+00
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.30E+05 963542 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
963542 963542 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
963542 963542 0 0 0 0
in 29520.63 seconds
Fits light curve has 963542 counts for 32.64 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > set binsize 2.0000000000E+00
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad12002220g300070_1.lc
Wrote FITS light curve to file ad12002220g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad12002220g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 02:34:59.680
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 20:30:21.680
No. of Rows ....... 14760 Bin Time (s) ...... 2.000
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 126.167 (s)
Intv 1 Start 9931 2:36: 2
Ser.1 Avg 32.64 Chisq 0.1057E+06 Var 201.1 Newbs. 271
Min 2.042 Max 45.50 expVar 0.5488 Bins 14760
Results from Statistical Analysis
Newbin Integration Time (s).. 126.17
Interval Duration (s)........ 64472.
No. of Newbins .............. 271
Average (c/s) ............... 32.636 +/- 0.45E-01
Standard Deviation (c/s)..... 14.181
Minimum (c/s)................ 2.0417
Maximum (c/s)................ 45.500
Variance ((c/s)**2).......... 201.10 +/- 17.
Expected Variance ((c/s)**2). 0.54880 +/- 0.47E-01
Third Moment ((c/s)**3)...... -2912.8
Average Deviation (c/s)...... 12.633
Skewness..................... -1.0214 +/- 0.15
Kurtosis.....................-0.73934 +/- 0.30
RMS fractional variation..... 0.43392 +/- 0.19E-01
Chi-Square................... 0.10570E+06 dof 270
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 126.167 (s)
Intv 1 Start 9931 2:36: 2
Ser.1 Avg 32.64 Chisq 0.1057E+06 Var 201.1 Newbs. 271
Min 2.042 Max 45.50 expVar 0.5488 Bins 14760
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> Extracting events from region ad12002220g325670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
6 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 1719 1006579 0 0 0
Writing events file
1719 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 169 95685 0 0 0
Writing events file
1888 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 14 9080 0 0 0
Writing events file
1902 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 1 589 0 0 0
Writing events file
1903 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 0 497 0 0 0
Writing events file
1903 events written to the output file
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 0 498 0 0 0
Writing events file
1903 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1114831 1903 1112928 0 0 0
in 29520.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300570m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300670l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad12002220g300070_2.lc with binsize 775.633892267394
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.30E+05 1903 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/events.tmp
Total Good Bad: Region Time Phase Cut
1903 1903 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1903 1903 0 0 0 0
in 29520.63 seconds
Fits light curve has 1903 counts for 6.4463E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > set binsize 775.633892267394
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad12002220g300070_2.lc
Wrote FITS light curve to file ad12002220g300070_2.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad12002220g300070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad12002220g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ CAS_A_C1H Start Time (d) .... 9931 02:34:59.680
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9931 20:30:21.680
No. of Rows ....... 41 Bin Time (s) ...... 775.6
Right Ascension ... 3.5070E+02 Internal time sys.. Converted to TJD
Declination ....... 5.8924E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 84 Newbins of 775.634 (s)
Intv 1 Start 9931 2:41:27
Ser.1 Avg 0.6418E-01 Chisq 279.7 Var 0.7296E-03 Newbs. 41
Min 0.1124E-01 Max 0.1101 expVar 0.1070E-03 Bins 41
Results from Statistical Analysis
Newbin Integration Time (s).. 775.63
Interval Duration (s)........ 63602.
No. of Newbins .............. 41
Average (c/s) ............... 0.64183E-01 +/- 0.16E-02
Standard Deviation (c/s)..... 0.27011E-01
Minimum (c/s)................ 0.11236E-01
Maximum (c/s)................ 0.11007
Variance ((c/s)**2).......... 0.72960E-03 +/- 0.16E-03
Expected Variance ((c/s)**2). 0.10696E-03 +/- 0.24E-04
Third Moment ((c/s)**3)......-0.92606E-05
Average Deviation (c/s)...... 0.23699E-01
Skewness.....................-0.46991 +/- 0.38
Kurtosis..................... -1.1222 +/- 0.77
RMS fractional variation..... 0.38877 +/- 0.51E-01
Chi-Square................... 279.66 dof 40
Chi-Square Prob of constancy. 0.10383E-36 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.94294E-16 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 84 Newbins of 775.634 (s)
Intv 1 Start 9931 2:41:27
Ser.1 Avg 0.6418E-01 Chisq 279.7 Var 0.7296E-03 Newbs. 41
Min 0.1124E-01 Max 0.1101 expVar 0.1070E-03 Bins 41
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad12002220g200170h.evt[2] ad12002220g200270m.evt[2] ad12002220g200370l.evt[2] ad12002220g200470m.evt[2] ad12002220g200570l.evt[2]-> Making L1 light curve of ft950802_0233_2030G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 166020 output records from 166088 good input G2_L1 records.-> Making L1 light curve of ft950802_0233_2030G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 26983 output records from 172232 good input G2_L1 records.-> Merging GTIs from the following files:
ad12002220g300170h.evt[2] ad12002220g300270m.evt[2] ad12002220g300370l.evt[2] ad12002220g300470h.evt[2] ad12002220g300570m.evt[2] ad12002220g300670l.evt[2]-> Making L1 light curve of ft950802_0233_2030G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 166979 output records from 167047 good input G3_L1 records.-> Making L1 light curve of ft950802_0233_2030G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 26989 output records from 173191 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 603641 128925 0 0 0
Writing events file
603641 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
732566 603641 128925 0 0 0
in 20904.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200170h_1.ulc use_events=yes
Wrote events list to file ad12002220g200170h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200170h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 732566 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.evt
Total Good Bad: Region Time Phase Cut
732566 1942 730624 0 0 0
Writing events file
1942 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
732566 1942 730624 0 0 0
in 20904.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200170h_2.ulc use_events=yes
Wrote events list to file ad12002220g200170h_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 77636 16419 0 0 0
Writing events file
77636 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
94055 77636 16419 0 0 0
in 6112.08 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200270m_1.ulc use_events=yes
Wrote events list to file ad12002220g200270m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200270m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 94055 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.evt
Total Good Bad: Region Time Phase Cut
94055 244 93811 0 0 0
Writing events file
244 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
94055 244 93811 0 0 0
in 6112.08 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200270m_2.ulc use_events=yes
Wrote events list to file ad12002220g200270m_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200370l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 7370 1542 0 0 0
Writing events file
7370 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8912 7370 1542 0 0 0
in 2335.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200370l_1.ulc use_events=yes
Wrote events list to file ad12002220g200370l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200370l_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 8912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.evt
Total Good Bad: Region Time Phase Cut
8912 15 8897 0 0 0
Writing events file
15 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8912 15 8897 0 0 0
in 2335.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200370l_2.ulc use_events=yes
Wrote events list to file ad12002220g200370l_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200470m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 408 80 0 0 0
Writing events file
408 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
488 408 80 0 0 0
in 32.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200470m_1.ulc use_events=yes
Wrote events list to file ad12002220g200470m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200470m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 488 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.evt
Total Good Bad: Region Time Phase Cut
488 1 487 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
488 1 487 0 0 0
in 32.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200470m_2.ulc use_events=yes
Wrote events list to file ad12002220g200470m_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200470m_2.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 414 76 0 0 0
Writing events file
414 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
490 414 76 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200570l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200570l_1.ulc use_events=yes
Wrote events list to file ad12002220g200570l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g200570l_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 490 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.evt
Total Good Bad: Region Time Phase Cut
490 1 489 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
490 1 489 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200570l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region ad12002220g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad12002220g200570l_2.ulc use_events=yes
Wrote events list to file ad12002220g200570l_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200570l_2.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 871425 136873 0 0 0
Writing events file
871425 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008298 871425 136873 0 0 0
in 20900.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300170h_1.ulc use_events=yes
Wrote events list to file ad12002220g300170h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300170h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.21E+05 1008298 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.evt
Total Good Bad: Region Time Phase Cut
1008298 1719 1006579 0 0 0
Writing events file
1719 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008298 1719 1006579 0 0 0
in 20900.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300170h_2.ulc use_events=yes
Wrote events list to file ad12002220g300170h_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 82913 12941 0 0 0
Writing events file
82913 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
95854 82913 12941 0 0 0
in 6112.08 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300270m_1.ulc use_events=yes
Wrote events list to file ad12002220g300270m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300270m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.61E+04 95854 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.evt
Total Good Bad: Region Time Phase Cut
95854 169 95685 0 0 0
Writing events file
169 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
95854 169 95685 0 0 0
in 6112.08 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300270m_2.ulc use_events=yes
Wrote events list to file ad12002220g300270m_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300370l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 7842 1252 0 0 0
Writing events file
7842 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9094 7842 1252 0 0 0
in 2335.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300370l_1.ulc use_events=yes
Wrote events list to file ad12002220g300370l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300370l_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.23E+04 9094 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.evt
Total Good Bad: Region Time Phase Cut
9094 14 9080 0 0 0
Writing events file
14 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9094 14 9080 0 0 0
in 2335.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300370l_2.ulc use_events=yes
Wrote events list to file ad12002220g300370l_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300470h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 513 77 0 0 0
Writing events file
513 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 513 77 0 0 0
in 12.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300470h_1.ulc use_events=yes
Wrote events list to file ad12002220g300470h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300470h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 590 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.evt
Total Good Bad: Region Time Phase Cut
590 1 589 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
590 1 589 0 0 0
in 12.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300470h_2.ulc use_events=yes
Wrote events list to file ad12002220g300470h_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300470h_2.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 410 87 0 0 0
Writing events file
410 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
497 410 87 0 0 0
in 32.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300570m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300570m_1.ulc use_events=yes
Wrote events list to file ad12002220g300570m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300570m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 497 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.evt
Total Good Bad: Region Time Phase Cut
497 0 497 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
497 0 497 0 0 0
in 32.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300570m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300570m_2.ulc use_events=yes
Wrote events list to file ad12002220g300570m_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300570m_2.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 439 59 0 0 0
Writing events file
439 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
498 439 59 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300670l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300670l_1.ulc use_events=yes
Wrote events list to file ad12002220g300670l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad12002220g300670l_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 498 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.evt
Total Good Bad: Region Time Phase Cut
498 0 498 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
498 0 498 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300670l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region ad12002220g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad12002220g300670l_2.ulc use_events=yes
Wrote events list to file ad12002220g300670l_2.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300670l_2.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.22E+02 594 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.evt
Total Good Bad: Region Time Phase Cut
594 220 374 0 0 0
Writing events file
220 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
594 220 374 0 0 0
in 21.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad12002220s000102h_1.ulc use_events=yes
Wrote events list to file ad12002220s000102h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.22E+02 635 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000112h.evt
Total Good Bad: Region Time Phase Cut
635 232 403 0 0 0
Writing events file
232 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
635 232 403 0 0 0
in 21.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad12002220s000112h_1.ulc use_events=yes
Wrote events list to file ad12002220s000112h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad12002220s000202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 179637 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.evt
Total Good Bad: Region Time Phase Cut
179637 151846 27791 0 0 0
Writing events file
151846 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
179637 151846 27791 0 0 0
in 7556.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad12002220s000202h_1.ulc use_events=yes
Wrote events list to file ad12002220s000202h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s000212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.76E+04 181215 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000212h.evt
Total Good Bad: Region Time Phase Cut
181215 153107 28108 0 0 0
Writing events file
153107 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
181215 153107 28108 0 0 0
in 7556.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad12002220s000212h_1.ulc use_events=yes
Wrote events list to file ad12002220s000212h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad12002220s000302m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.65E+03 10060 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.evt
Total Good Bad: Region Time Phase Cut
10060 8846 1214 0 0 0
Writing events file
8846 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10060 8846 1214 0 0 0
in 653.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad12002220s000302m_1.ulc use_events=yes
Wrote events list to file ad12002220s000302m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s000702h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 536 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.evt
Total Good Bad: Region Time Phase Cut
536 450 86 0 0 0
Writing events file
450 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
536 450 86 0 0 0
in 28.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s000702h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad12002220s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad12002220s000702h_1.ulc use_events=yes
Wrote events list to file ad12002220s000702h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s100202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.76E+04 157771 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.evt
Total Good Bad: Region Time Phase Cut
157771 133633 24138 0 0 0
Writing events file
133633 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
157771 133633 24138 0 0 0
in 7609.58 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad12002220s100202h_1.ulc use_events=yes
Wrote events list to file ad12002220s100202h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s100212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.76E+04 158939 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100212h.evt
Total Good Bad: Region Time Phase Cut
158939 134594 24345 0 0 0
Writing events file
134594 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158939 134594 24345 0 0 0
in 7609.58 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100212h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad12002220s100212h_1.ulc use_events=yes
Wrote events list to file ad12002220s100212h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad12002220s100502l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.32E+02 239 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.evt
Total Good Bad: Region Time Phase Cut
239 166 73 0 0 0
Writing events file
166 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
239 166 73 0 0 0
in 32.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100502l.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad12002220s100502l_1.ulc use_events=yes
Wrote events list to file ad12002220s100502l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad12002220s100702h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.28E+02 866 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.evt
Total Good Bad: Region Time Phase Cut
866 667 199 0 0 0
Writing events file
667 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
866 667 199 0 0 0
in 28.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220s100702h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad12002220s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad12002220s100702h_1.ulc use_events=yes
Wrote events list to file ad12002220s100702h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/12002220.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) ***
total number of superframes: 16024
frame data: 81484449.679722 ---> 81484557.6793825
S0, C1, 4 ccd mode; Output File = fr950802_0233.2030_s0c1m4a.fits
frame data: 81484577.6793196 ---> 81484721.6788651
S0, C2, 4 ccd mode; Output File = fr950802_0233.2030_s0c2m4a.fits
frame data: 81484741.6788018 ---> 81484885.6783459
S0, C3, 4 ccd mode; Output File = fr950802_0233.2030_s0c3m4a.fits
frame data: 81485013.6779402 ---> 81485157.677481
S1, C2, 4 ccd mode; Output File = fr950802_0233.2030_s1c2m4a.fits
frame data: 81485177.6774172 ---> 81485321.676958
S1, C3, 4 ccd mode; Output File = fr950802_0233.2030_s1c3m4a.fits
frame data: 81485341.6768942 ---> 81485485.676433
S1, C0, 4 ccd mode; Output File = fr950802_0233.2030_s1c0m4a.fits
frame data: 81485505.6763688 ---> 81485649.6759059
S1, C1, 4 ccd mode; Output File = fr950802_0233.2030_s1c1m4a.fits
Total of 7 sets of frame data are extracted.
-> Processing fr950802_0233.2030_s0c1m4a.fitsDark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s0c1m4a.fits Output zero level image : rdd.tmp Bias level = 294-> Adding keywords to header of fr950802_0233.2030_s0c1m4a.fits
infile,s,h,"row.tmp",,,"Name of FITS file and [ext#]" outfile,s,h,"STDOUT",,,"Name of optional output file" columns,s,h,"@mkf_cols.tmp",,,"Names of columns" rows,s,h,"1",,,"Lists of rows" fldsep,s,h,,,,"Define a new field separator (default is space)" pagewidth,i,h,256,1,256,"Page width" prhead,b,h,no,,,"Print header keywords?" prdata,b,h,yes,,,"Print data?" showcol,b,h,no,,,"Print column names?" showunit,b,h,no,,,"Print column units?" showrow,b,h,no,,,"Print row numbers?" showscale,b,h,no,,,"Show scaled values?" align,b,h,no,,,"Align columns with names?" skip,i,h,1,1,,"Print every nth row" tdisp,b,h,yes,,,"Use TDISPn keywords?" wrap,b,h,no,,,"Display entire row at once?" page,b,h,no,,,"Page through output to terminal" clobber,b,h,no,,,"Overwrite output file if exists?" sensecase,b,h,no,,,"Be case sensitive about column names?" more,s,h,"yes",,,"More?" mode,s,h,"ql",,,""-> Processing fr950802_0233.2030_s0c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s0c2m4a.fits Output zero level image : rdd.tmp Bias level = 328-> Adding keywords to header of fr950802_0233.2030_s0c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s0c3m4a.fits Output zero level image : rdd.tmp Bias level = 308-> Adding keywords to header of fr950802_0233.2030_s0c3m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s1c0m4a.fits Output zero level image : rdd.tmp Bias level = 222-> Adding keywords to header of fr950802_0233.2030_s1c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s1c1m4a.fits Output zero level image : rdd.tmp Bias level = 190-> Adding keywords to header of fr950802_0233.2030_s1c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s1c2m4a.fits Output zero level image : rdd.tmp Bias level = 181-> Adding keywords to header of fr950802_0233.2030_s1c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr950802_0233.2030_s1c3m4a.fits Output zero level image : rdd.tmp Bias level = 218-> Adding keywords to header of fr950802_0233.2030_s1c3m4a.fits
1 ad12002220g200170h.unf 1084270 1 ad12002220g200270m.unf 1084270 1 ad12002220g200370l.unf 1084270 1 ad12002220g200470m.unf 1084270 1 ad12002220g200570l.unf 1084270-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
4 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
5 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.unf
Total Good Bad: Region Time Phase Cut
960373 6512 953861 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.unf
Total Good Bad: Region Time Phase Cut
105939 1819 104120 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.unf
Total Good Bad: Region Time Phase Cut
16934 1748 15186 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.unf
Total Good Bad: Region Time Phase Cut
512 3 509 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.unf
Total Good Bad: Region Time Phase Cut
512 2 510 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1084270 10084 1074186 0 0 0
in 49673.85 seconds
Spectrum has 10084 counts for 0.2030 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 49674. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200470m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > read events ad12002220g200570l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad12002220g220170.cal group=yes
Wrote spectrum to ad12002220g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 14:07:24 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad12002220g220170.cal
Net count rate (cts/s) for file 1 0.2030 +/- 2.0221E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.6092E+06 using 84 PHA bins.
Reduced chi-squared = 2.0899E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.5984E+06 using 84 PHA bins.
Reduced chi-squared = 2.0493E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.5984E+06 using 84 PHA bins.
Reduced chi-squared = 2.0233E+04
!XSPEC> renorm
Chi-Squared = 2908. using 84 PHA bins.
Reduced chi-squared = 36.81
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2234.5 0 1.000 5.893 0.1126 6.0100E-02
5.2493E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
833.88 0 1.000 5.864 0.1638 9.1141E-02
4.6130E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
284.99 -1 1.000 5.916 0.1837 0.1295
2.9922E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
253.56 -2 1.000 5.944 0.1958 0.1420
2.1742E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
249.71 -3 1.000 5.932 0.1851 0.1389
2.4767E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
249.37 -4 1.000 5.936 0.1878 0.1401
2.3543E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
249.23 -5 1.000 5.935 0.1864 0.1397
2.3993E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
249.23 0 1.000 5.935 0.1864 0.1397
2.3966E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93464 +/- 0.57459E-02
3 3 2 gaussian/b Sigma 0.186400 +/- 0.62182E-02
4 4 2 gaussian/b norm 0.139674 +/- 0.21807E-02
5 2 3 gaussian/b LineE 6.53406 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.195587 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.396590E-02 +/- 0.15315E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 249.2 using 84 PHA bins.
Reduced chi-squared = 3.155
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad12002220g220170.cal peaks at 5.93464 +/- 0.0057459 keV1 ad12002220g300170h.unf 1422768 1 ad12002220g300270m.unf 1422768 1 ad12002220g300370l.unf 1422768 1 ad12002220g300470h.unf 1422768 1 ad12002220g300570m.unf 1422768 1 ad12002220g300670l.unf 1422768-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
2 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
3 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
4 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
5 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
6 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.unf
Total Good Bad: Region Time Phase Cut
1298758 5713 1293045 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.unf
Total Good Bad: Region Time Phase Cut
105800 1494 104306 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.unf
Total Good Bad: Region Time Phase Cut
16574 1408 15166 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.unf
Total Good Bad: Region Time Phase Cut
612 2 610 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.unf
Total Good Bad: Region Time Phase Cut
512 3 509 0 0 0
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.unf
Total Good Bad: Region Time Phase Cut
512 2 510 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1422768 8622 1414146 0 0 0
in 49681.85 seconds
Spectrum has 8622 counts for 0.1735 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 49682. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad12002220g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!xsel:ASCA > read events ad12002220g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300570m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > read events ad12002220g300670l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 6
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad12002220g320170.cal group=yes
Wrote spectrum to ad12002220g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 14:09:00 23-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad12002220g320170.cal
Net count rate (cts/s) for file 1 0.1735 +/- 1.8705E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.9125E+06 using 84 PHA bins.
Reduced chi-squared = 2.4838E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.8964E+06 using 84 PHA bins.
Reduced chi-squared = 2.4313E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.8964E+06 using 84 PHA bins.
Reduced chi-squared = 2.4005E+04
!XSPEC> renorm
Chi-Squared = 2764. using 84 PHA bins.
Reduced chi-squared = 34.98
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2230.8 0 1.000 5.893 7.9933E-02 5.2292E-02
4.4897E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
841.57 0 1.000 5.867 0.1250 8.1856E-02
3.8476E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
246.07 -1 1.000 5.916 0.1347 0.1156
2.5223E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
178.19 -2 1.000 5.946 0.1487 0.1282
1.8282E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
177.84 -3 1.000 5.945 0.1470 0.1283
1.8216E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
177.83 -4 1.000 5.945 0.1468 0.1283
1.8229E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
177.83 -5 1.000 5.945 0.1468 0.1283
1.8232E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94534 +/- 0.46464E-02
3 3 2 gaussian/b Sigma 0.146788 +/- 0.59232E-02
4 4 2 gaussian/b norm 0.128327 +/- 0.18692E-02
5 2 3 gaussian/b LineE 6.54585 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.154023 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.823203E-02 +/- 0.10989E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 177.8 using 84 PHA bins.
Reduced chi-squared = 2.251
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad12002220g320170.cal peaks at 5.94534 +/- 0.0046464 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.18E+05 554010 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000102h.unf
Total Good Bad: Region Time Phase Cut
554010 6588 0 547422 0 0
Writing events file
6588 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
554010 6588 0 547422 0 0
in 530.22 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6588
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 96 3315
Flickering pixels iter, pixels & cnts : 1 21 211
cleaning chip # 1
Hot pixels & counts : 1 33
cleaning chip # 2
Hot pixels & counts : 36 1003
Flickering pixels iter, pixels & cnts : 1 7 36
cleaning chip # 3
Hot pixels & counts : 55 1802
Flickering pixels iter, pixels & cnts : 1 9 69
Number of pixels rejected : 225
Number of (internal) image counts : 6588
Number of image cts rejected (N, %) : 6469 98.1936874
By chip : 0 1 2 3
Pixels rejected : 117 1 43 64
Image counts : 3574 51 1062 1901
Image cts rejected: 3526 33 1039 1871
Image cts rej (%) : 98.66 64.71 97.83 98.42
filtering data...
Total counts : 3574 51 1062 1901
Total cts rejected: 3526 33 1039 1871
Total cts rej (%) : 98.66 64.71 97.83 98.42
Number of clean counts accepted : 119
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 225
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.18E+05 569248 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000112h.unf
Total Good Bad: Region Time Phase Cut
569248 6705 0 562543 0 0
Writing events file
6705 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
569248 6705 0 562543 0 0
in 530.22 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6705
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 98 3394
Flickering pixels iter, pixels & cnts : 1 19 195
cleaning chip # 1
Hot pixels & counts : 1 33
cleaning chip # 2
Hot pixels & counts : 36 1014
Flickering pixels iter, pixels & cnts : 1 7 36
cleaning chip # 3
Hot pixels & counts : 55 1812
Flickering pixels iter, pixels & cnts : 1 9 70
Number of pixels rejected : 225
Number of (internal) image counts : 6705
Number of image cts rejected (N, %) : 6554 97.7479477
By chip : 0 1 2 3
Pixels rejected : 117 1 43 64
Image counts : 3647 59 1077 1922
Image cts rejected: 3589 33 1050 1882
Image cts rej (%) : 98.41 55.93 97.49 97.92
filtering data...
Total counts : 3647 59 1077 1922
Total cts rejected: 3589 33 1050 1882
Total cts rej (%) : 98.41 55.93 97.49 97.92
Number of clean counts accepted : 151
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 225
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.91E+04 234025 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s000202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.91E+04 235064 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s000212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s000212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.64E+04 110866 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s000302m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000302m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 08:00:09 0.63E+04 5816 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000402m.unf
Total Good Bad: Region Time Phase Cut
5816 5789 0 27 0 0
Writing events file
5789 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5816 5789 0 27 0 0
in 1373.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s000402m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000402m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 5789
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 30 2005
Flickering pixels iter, pixels & cnts : 1 6 58
cleaning chip # 1
Hot pixels & counts : 1 84
cleaning chip # 2
Hot pixels & counts : 29 1659
Flickering pixels iter, pixels & cnts : 1 5 30
cleaning chip # 3
Hot pixels & counts : 27 1683
Flickering pixels iter, pixels & cnts : 1 11 94
Number of pixels rejected : 109
Number of (internal) image counts : 5789
Number of image cts rejected (N, %) : 5613 96.9597549
By chip : 0 1 2 3
Pixels rejected : 36 1 34 38
Image counts : 2098 141 1742 1808
Image cts rejected: 2063 84 1689 1777
Image cts rej (%) : 98.33 59.57 96.96 98.29
filtering data...
Total counts : 2098 141 1742 1808
Total cts rejected: 2063 84 1689 1777
Total cts rej (%) : 98.33 59.57 96.96 98.29
Number of clean counts accepted : 176
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 109
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000412m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 MEDIUM 02/08/95 08:00:09 0.63E+04 5942 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000412m.unf
Total Good Bad: Region Time Phase Cut
5942 5896 0 46 0 0
Writing events file
5896 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5942 5896 0 46 0 0
in 1373.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s000412m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000412m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 5896
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 30 2016
Flickering pixels iter, pixels & cnts : 1 6 58
cleaning chip # 1
Hot pixels & counts : 1 85
cleaning chip # 2
Hot pixels & counts : 29 1678
Flickering pixels iter, pixels & cnts : 1 5 31
cleaning chip # 3
Hot pixels & counts : 27 1711
Flickering pixels iter, pixels & cnts : 1 11 97
Number of pixels rejected : 109
Number of (internal) image counts : 5896
Number of image cts rejected (N, %) : 5676 96.2686539
By chip : 0 1 2 3
Pixels rejected : 36 1 34 38
Image counts : 2116 152 1776 1852
Image cts rejected: 2074 85 1709 1808
Image cts rej (%) : 98.02 55.92 96.23 97.62
filtering data...
Total counts : 2116 152 1776 1852
Total cts rejected: 2074 85 1709 1808
Total cts rej (%) : 98.02 55.92 96.23 97.62
Number of clean counts accepted : 220
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 109
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000502l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.96E+04 10092 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000502l.unf
Total Good Bad: Region Time Phase Cut
10092 1516 0 8576 0 0
Writing events file
1516 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10092 1516 0 8576 0 0
in 2737.14 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s000502l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000502l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1516
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 10 1282
Flickering pixels iter, pixels & cnts : 1 2 9
cleaning chip # 3
Number of pixels rejected : 12
Number of (internal) image counts : 1516
Number of image cts rejected (N, %) : 1291 85.1583099
By chip : 0 1 2 3
Pixels rejected : 0 0 12 0
Image counts : 0 116 1400 0
Image cts rejected: 0 0 1291 0
Image cts rej (%) : 0.00 0.00 92.21 0.00
filtering data...
Total counts : 0 116 1400 0
Total cts rejected: 0 0 1291 0
Total cts rej (%) : 0.00 0.00 92.21 0.00
Number of clean counts accepted : 225
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 12
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000602l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 02:41:45 0.33E+04 2518 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000602l.unf
Total Good Bad: Region Time Phase Cut
2518 819 0 1699 0 0
Writing events file
819 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2518 819 0 1699 0 0
in 640.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000602l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s000602l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000602l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 819
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 8 243
Flickering pixels iter, pixels & cnts : 1 2 9
cleaning chip # 1
Hot pixels & counts : 1 37
cleaning chip # 2
Hot pixels & counts : 9 262
cleaning chip # 3
Hot pixels & counts : 7 229
Number of pixels rejected : 27
Number of (internal) image counts : 819
Number of image cts rejected (N, %) : 780 95.2380981
By chip : 0 1 2 3
Pixels rejected : 10 1 9 7
Image counts : 261 54 267 237
Image cts rejected: 252 37 262 229
Image cts rej (%) : 96.55 68.52 98.13 96.62
filtering data...
Total counts : 261 54 267 237
Total cts rejected: 252 37 262 229
Total cts rej (%) : 96.55 68.52 98.13 96.62
Number of clean counts accepted : 39
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 27
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000612l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT2 LOW 02/08/95 02:41:45 0.33E+04 2590 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s000612l.unf
Total Good Bad: Region Time Phase Cut
2590 832 0 1758 0 0
Writing events file
832 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2590 832 0 1758 0 0
in 640.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000612l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s000612l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s000612l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 832
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 8 243
Flickering pixels iter, pixels & cnts : 1 2 9
cleaning chip # 1
Hot pixels & counts : 1 37
cleaning chip # 2
Hot pixels & counts : 9 266
cleaning chip # 3
Hot pixels & counts : 7 229
Number of pixels rejected : 27
Number of (internal) image counts : 832
Number of image cts rejected (N, %) : 784 94.2307663
By chip : 0 1 2 3
Pixels rejected : 10 1 9 7
Image counts : 262 58 272 240
Image cts rejected: 252 37 266 229
Image cts rej (%) : 96.18 63.79 97.79 95.42
filtering data...
Total counts : 262 58 272 240
Total cts rejected: 252 37 266 229
Total cts rej (%) : 96.18 63.79 97.79 95.42
Number of clean counts accepted : 48
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 27
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s000702h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.48E+02 1297 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s000702h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s000702h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad12002220s000702h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 02:41:25 0.18E+05 677303 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100102h.unf
Total Good Bad: Region Time Phase Cut
677303 8157 0 669146 0 0
Writing events file
8157 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
677303 8157 0 669146 0 0
in 532.13 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8157
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 73 2218
Flickering pixels iter, pixels & cnts : 1 28 222
cleaning chip # 1
Hot pixels & counts : 89 2691
Flickering pixels iter, pixels & cnts : 1 21 165
cleaning chip # 2
Hot pixels & counts : 76 2556
Flickering pixels iter, pixels & cnts : 1 16 135
cleaning chip # 3
Hot pixels & counts : 1 35
Number of pixels rejected : 304
Number of (internal) image counts : 8157
Number of image cts rejected (N, %) : 8022 98.3449783
By chip : 0 1 2 3
Pixels rejected : 101 110 92 1
Image counts : 2469 2902 2733 53
Image cts rejected: 2440 2856 2691 35
Image cts rej (%) : 98.83 98.41 98.46 66.04
filtering data...
Total counts : 2469 2902 2733 53
Total cts rejected: 2440 2856 2691 35
Total cts rej (%) : 98.83 98.41 98.46 66.04
Number of clean counts accepted : 135
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 304
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 02:41:25 0.18E+05 699695 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100112h.unf
Total Good Bad: Region Time Phase Cut
699695 8340 0 691355 0 0
Writing events file
8340 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
699695 8340 0 691355 0 0
in 532.13 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8340
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 2272
Flickering pixels iter, pixels & cnts : 1 28 220
cleaning chip # 1
Hot pixels & counts : 91 2754
Flickering pixels iter, pixels & cnts : 1 21 169
cleaning chip # 2
Hot pixels & counts : 76 2571
Flickering pixels iter, pixels & cnts : 1 17 149
cleaning chip # 3
Hot pixels & counts : 1 35
Number of pixels rejected : 308
Number of (internal) image counts : 8340
Number of image cts rejected (N, %) : 8170 97.9616318
By chip : 0 1 2 3
Pixels rejected : 102 112 93 1
Image counts : 2537 2981 2766 56
Image cts rejected: 2492 2923 2720 35
Image cts rej (%) : 98.23 98.05 98.34 62.50
filtering data...
Total counts : 2537 2981 2766 56
Total cts rejected: 2492 2923 2720 35
Total cts rej (%) : 98.23 98.05 98.34 62.50
Number of clean counts accepted : 170
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 308
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 05:50:05 0.91E+04 215087 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s100202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 HIGH 02/08/95 05:50:05 0.91E+04 215555 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s100212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad12002220s100212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 05:23:53 0.64E+04 116252 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s100302m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100302m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT MEDIUM 02/08/95 08:00:09 0.63E+04 7278 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100402m.unf
Total Good Bad: Region Time Phase Cut
7278 6481 0 797 0 0
Writing events file
6481 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7278 6481 0 797 0 0
in 1373.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100402m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s100402m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100402m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 6481
Total counts in chip images : 6480
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 30 1769
Flickering pixels iter, pixels & cnts : 1 20 180
cleaning chip # 1
Hot pixels & counts : 27 1948
Flickering pixels iter, pixels & cnts : 1 16 188
cleaning chip # 2
Hot pixels & counts : 28 2017
Flickering pixels iter, pixels & cnts : 1 9 139
cleaning chip # 3
Hot pixels & counts : 1 83
Flickering pixels iter, pixels & cnts : 1 1 4
Number of pixels rejected : 132
Number of (internal) image counts : 6480
Number of image cts rejected (N, %) : 6328 97.6543198
By chip : 0 1 2 3
Pixels rejected : 50 43 37 2
Image counts : 1981 2163 2192 144
Image cts rejected: 1949 2136 2156 87
Image cts rej (%) : 98.38 98.75 98.36 60.42
filtering data...
Total counts : 1981 2164 2192 144
Total cts rejected: 1949 2137 2156 87
Total cts rej (%) : 98.38 98.75 98.36 60.42
Number of clean counts accepted : 152
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 132
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100412m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 MEDIUM 02/08/95 08:00:09 0.63E+04 7531 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100412m.unf
Total Good Bad: Region Time Phase Cut
7531 6589 0 942 0 0
Writing events file
6589 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7531 6589 0 942 0 0
in 1373.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100412m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s100412m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100412m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6589
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 30 1812
Flickering pixels iter, pixels & cnts : 1 20 184
cleaning chip # 1
Hot pixels & counts : 27 1967
Flickering pixels iter, pixels & cnts : 1 16 194
cleaning chip # 2
Hot pixels & counts : 28 2025
Flickering pixels iter, pixels & cnts : 1 9 140
cleaning chip # 3
Hot pixels & counts : 1 84
Flickering pixels iter, pixels & cnts : 1 1 4
Number of pixels rejected : 132
Number of (internal) image counts : 6589
Number of image cts rejected (N, %) : 6410 97.2833481
By chip : 0 1 2 3
Pixels rejected : 50 43 37 2
Image counts : 2034 2196 2205 154
Image cts rejected: 1996 2161 2165 88
Image cts rej (%) : 98.13 98.41 98.19 57.14
filtering data...
Total counts : 2034 2196 2205 154
Total cts rejected: 1996 2161 2165 88
Total cts rej (%) : 98.13 98.41 98.19 57.14
Number of clean counts accepted : 179
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 132
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100502l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 04:43:21 0.96E+04 18368 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100502l.unf
Total Good Bad: Region Time Phase Cut
18368 3893 0 14475 0 0
Writing events file
3893 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18368 3893 0 14475 0 0
in 2737.14 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100502l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s100502l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100502l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3893
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 21 3490
Flickering pixels iter, pixels & cnts : 1 6 47
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 1 97
Flickering pixels iter, pixels & cnts : 1 1 4
Number of pixels rejected : 29
Number of (internal) image counts : 3893
Number of image cts rejected (N, %) : 3638 93.4497833
By chip : 0 1 2 3
Pixels rejected : 27 0 0 2
Image counts : 3693 0 0 200
Image cts rejected: 3537 0 0 101
Image cts rej (%) : 95.78 0.00 0.00 50.50
filtering data...
Total counts : 3693 0 0 200
Total cts rejected: 3537 0 0 101
Total cts rej (%) : 95.78 0.00 0.00 50.50
Number of clean counts accepted : 255
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 29
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100602l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT LOW 02/08/95 02:41:45 0.33E+04 3213 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100602l.unf
Total Good Bad: Region Time Phase Cut
3213 873 0 2340 0 0
Writing events file
873 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3213 873 0 2340 0 0
in 640.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100602l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad12002220s100602l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100602l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 873
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 7 227
Flickering pixels iter, pixels & cnts : 1 2 10
cleaning chip # 1
Hot pixels & counts : 7 226
Flickering pixels iter, pixels & cnts : 1 3 40
cleaning chip # 2
Hot pixels & counts : 7 261
Flickering pixels iter, pixels & cnts : 1 2 32
cleaning chip # 3
Hot pixels & counts : 1 37
Number of pixels rejected : 29
Number of (internal) image counts : 873
Number of image cts rejected (N, %) : 833 95.4180984
By chip : 0 1 2 3
Pixels rejected : 9 10 9 1
Image counts : 245 274 302 52
Image cts rejected: 237 266 293 37
Image cts rej (%) : 96.73 97.08 97.02 71.15
filtering data...
Total counts : 245 274 302 52
Total cts rejected: 237 266 293 37
Total cts rej (%) : 96.73 97.08 97.02 71.15
Number of clean counts accepted : 40
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 29
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100612l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT2 LOW 02/08/95 02:41:45 0.33E+04 3348 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220s100612l.unf
Total Good Bad: Region Time Phase Cut
3348 897 0 2451 0 0
Writing events file
897 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3348 897 0 2451 0 0
in 640.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100612l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad12002220s100612l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad12002220s100612l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 897
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 7 227
Flickering pixels iter, pixels & cnts : 1 2 16
cleaning chip # 1
Hot pixels & counts : 7 236
Flickering pixels iter, pixels & cnts : 1 4 44
cleaning chip # 2
Hot pixels & counts : 7 262
Flickering pixels iter, pixels & cnts : 1 2 32
cleaning chip # 3
Hot pixels & counts : 1 37
Number of pixels rejected : 30
Number of (internal) image counts : 897
Number of image cts rejected (N, %) : 854 95.2062454
By chip : 0 1 2 3
Pixels rejected : 9 11 9 1
Image counts : 252 286 303 56
Image cts rejected: 243 280 294 37
Image cts rej (%) : 96.43 97.90 97.03 66.07
filtering data...
Total counts : 252 286 303 56
Total cts rejected: 243 280 294 37
Total cts rej (%) : 96.43 97.90 97.03 66.07
Number of clean counts accepted : 43
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 30
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad12002220s100702h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 CAS_A_C1 BRIGHT HIGH 02/08/95 04:42:57 0.48E+02 1555 1001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220s100702h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220s100702h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad12002220s100702h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.unf
Total Good Bad: Region Time Phase Cut
960373 402 0 959971 0 0
Writing events file
402 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
960373 402 0 959971 0 0
in 498.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad12002220g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 960373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200170h.unf
Total Good Bad: Region Time Phase Cut
960373 402 0 959971 0 0
Writing events file
402 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
960373 402 0 959971 0 0
in 455.55 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.unf
Total Good Bad: Region Time Phase Cut
105939 1413 0 104526 0 0
Writing events file
1413 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105939 1413 0 104526 0 0
in 1415.75 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad12002220g200270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105939 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200270m.unf
Total Good Bad: Region Time Phase Cut
105939 3150 0 102789 0 0
Writing events file
3150 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105939 3150 0 102789 0 0
in 3480.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g200370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.unf
Total Good Bad: Region Time Phase Cut
16934 2136 0 14798 0 0
Writing events file
2136 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16934 2136 0 14798 0 0
in 2672.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad12002220g200370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16934 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g200370l.unf
Total Good Bad: Region Time Phase Cut
16934 3288 0 13646 0 0
Writing events file
3288 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16934 3288 0 13646 0 0
in 3936.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g200470m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200470m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g200470m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200470m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200570l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g200570l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g200570l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad12002220g200570l.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.unf
Total Good Bad: Region Time Phase Cut
1298758 378 0 1298380 0 0
Writing events file
378 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1298758 378 0 1298380 0 0
in 498.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad12002220g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 02:34:45 0.28E+05 1298758 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300170h.unf
Total Good Bad: Region Time Phase Cut
1298758 348 0 1298410 0 0
Writing events file
348 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1298758 348 0 1298410 0 0
in 455.55 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.unf
Total Good Bad: Region Time Phase Cut
105800 1344 0 104456 0 0
Writing events file
1344 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105800 1344 0 104456 0 0
in 1415.75 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad12002220g300270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 05:24:05 0.11E+05 105800 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300270m.unf
Total Good Bad: Region Time Phase Cut
105800 3003 0 102797 0 0
Writing events file
3003 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
105800 3003 0 102797 0 0
in 3480.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g300370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.unf
Total Good Bad: Region Time Phase Cut
16574 1914 0 14660 0 0
Writing events file
1914 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16574 1914 0 14660 0 0
in 2672.26 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad12002220g300370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 02:41:57 0.98E+04 16574 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/12002220.003/ad12002220g300370l.unf
Total Good Bad: Region Time Phase Cut
16574 3111 0 13463 0 0
Writing events file
3111 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16574 3111 0 13463 0 0
in 3936.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad12002220g300470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300470h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH HIGH 02/08/95 16:56:15 0.12E+02 612 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300470h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300570m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300570m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH MEDIUM 02/08/95 13:23:33 0.32E+02 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300570m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300570m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300570m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300670l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 CAS_A_C1 PH LOW 02/08/95 06:18:29 0.13E+03 512 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/12002220.003/ad12002220g300670l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/12002220.003/
Setting mkf directory to /data/data23/seq_proc/12002220.003/
!earthevents:ASCA > read events ad12002220g300670l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/12002220.003/
HK Directory is: /data/data23/seq_proc/12002220.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad12002220g300670l.brt since it contains 0 eventsOffset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad12002220s000102h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000202h.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000702h.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000102h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000202h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000702h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000102h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad12002220s000202h.unf|S0CCDLST|1 2 1 2|S0 CCD readout order ad12002220s000702h.unf|S0CCDLST|1 2 1 2|S0 CCD readout order ad12002220s000102h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad12002220s000202h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad12002220s000702h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion-> listing ad12002220s000102h.unf
ad12002220s000302m.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000402m.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000302m.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000402m.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000302m.unf|S0CCDLST|1 2 1 2|S0 CCD readout order ad12002220s000402m.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad12002220s000302m.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad12002220s000402m.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad12002220s000302m.unf
ad12002220s000502l.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000602l.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000502l.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000602l.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000502l.unf|S0CCDLST|1 2 1 2|S0 CCD readout order ad12002220s000602l.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad12002220s000502l.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad12002220s000602l.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad12002220s000502l.unf
ad12002220s000112h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000212h.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000112h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000212h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000112h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad12002220s000212h.unf|S0CCDLST|1 2 1 2|S0 CCD readout order-> listing ad12002220s000112h.unf
ad12002220s000101h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000201h.unf|S0CCDPOW|0110|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad12002220s000101h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000201h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad12002220s000101h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad12002220s000201h.unf|S0CCDLST|1 2 1 2|S0 CCD readout order-> listing ad12002220s000101h.unf
ad12002220s100102h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100202h.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100702h.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100102h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100202h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100702h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100102h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order ad12002220s100202h.unf|S1CCDLST|3 0 3 0|S1 CCD readout order ad12002220s100702h.unf|S1CCDLST|3 0 3 0|S1 CCD readout order ad12002220s100102h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad12002220s100202h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad12002220s100702h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion-> listing ad12002220s100102h.unf
ad12002220s100302m.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100402m.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100302m.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100402m.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100302m.unf|S1CCDLST|3 0 3 0|S1 CCD readout order ad12002220s100402m.unf|S1CCDLST|2 3 0 1|S1 CCD readout order ad12002220s100302m.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad12002220s100402m.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad12002220s100302m.unf
ad12002220s100502l.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100602l.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100502l.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100602l.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100502l.unf|S1CCDLST|3 0 3 0|S1 CCD readout order ad12002220s100602l.unf|S1CCDLST|2 3 0 1|S1 CCD readout order ad12002220s100502l.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad12002220s100602l.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad12002220s100502l.unf
ad12002220s100112h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100212h.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100112h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100212h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100112h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order ad12002220s100212h.unf|S1CCDLST|3 0 3 0|S1 CCD readout order-> listing ad12002220s100112h.unf
ad12002220s100101h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100201h.unf|S1CCDPOW|1001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad12002220s100101h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100201h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad12002220s100101h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order ad12002220s100201h.unf|S1CCDLST|3 0 3 0|S1 CCD readout order-> listing ad12002220s100101h.unf
ad12002220g200270m.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad12002220g200470m.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad12002220g200270m.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad12002220g200470m.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad12002220g200270m.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad12002220g200470m.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad12002220g200270m.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad12002220g200470m.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad12002220g200270m.unf|SP_A_U_F|239|Spread discri A_U for FLF method (0-255) ad12002220g200470m.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad12002220g200270m.unf|SP_B_F|226|Spread discri B for FLF method (0-255) ad12002220g200470m.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad12002220g200270m.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad12002220g200470m.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad12002220g200270m.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad12002220g200470m.unf|SP_PH_F|31098|Spread discri PH for FLF method (0-1023)-> listing ad12002220g200270m.unf
ad12002220g200370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad12002220g200570l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad12002220g200370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad12002220g200570l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad12002220g200370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad12002220g200570l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad12002220g200370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad12002220g200570l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad12002220g200370l.unf|SP_A_U_F|239|Spread discri A_U for FLF method (0-255) ad12002220g200570l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad12002220g200370l.unf|SP_B_F|226|Spread discri B for FLF method (0-255) ad12002220g200570l.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad12002220g200370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad12002220g200570l.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad12002220g200370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad12002220g200570l.unf|SP_PH_F|31098|Spread discri PH for FLF method (0-1023)-> listing ad12002220g200370l.unf
ad12002220g300170h.unf|CPU2|RUN|CPU2 run/stop ad12002220g300470h.unf|CPU2|STOP|CPU2 run/stop ad12002220g300170h.unf|C2_PGVER|1|CPU2 program version number ad12002220g300470h.unf|C2_PGVER|0|CPU2 program version number-> listing ad12002220g300170h.unf
ad12002220g300270m.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad12002220g300570m.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad12002220g300270m.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad12002220g300570m.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad12002220g300270m.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad12002220g300570m.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad12002220g300270m.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad12002220g300570m.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad12002220g300270m.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255) ad12002220g300570m.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad12002220g300270m.unf|SP_B_F|224|Spread discri B for FLF method (0-255) ad12002220g300570m.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad12002220g300270m.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad12002220g300570m.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad12002220g300270m.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad12002220g300570m.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)-> listing ad12002220g300270m.unf
ad12002220g300370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255) ad12002220g300670l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255) ad12002220g300370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255) ad12002220g300670l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255) ad12002220g300370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255) ad12002220g300670l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255) ad12002220g300370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255) ad12002220g300670l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255) ad12002220g300370l.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255) ad12002220g300670l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255) ad12002220g300370l.unf|SP_B_F|224|Spread discri B for FLF method (0-255) ad12002220g300670l.unf|SP_B_F|120|Spread discri B for FLF method (0-255) ad12002220g300370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255) ad12002220g300670l.unf|SP_C_F|120|Spread discri C for FLF method (0-255) ad12002220g300370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023) ad12002220g300670l.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)-> listing ad12002220g300370l.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files