The following information is also available:
Time column is TIME ORDERED-> Fetching fa960301_0512.0500.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 99810769.002600 99896473.735500
Data file start and stop ascatime : 99810769.002600 99896473.735500
Aspecting run start and stop ascatime : 99810769.002682 99896473.735401
Time interval averaged over (seconds) : 85704.732719
Total pointing and manuver time (sec) : 52811.472656 32893.476562
Mean boresight Euler angles : 85.585508 92.146437 189.670569
RA DEC SUN ANGLE
Mean solar position (deg) : 341.91 -7.67
Mean aberration (arcsec) : 5.50 -8.36
Mean sat X-axis (deg) : 7.981587 80.096303 88.76
Mean sat Y-axis (deg) : 355.219834 -9.663719 13.31
Mean sat Z-axis (deg) : 85.585508 -2.146437 103.25
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 85.359619 -2.319219 99.662117 0.745853
Minimum 85.264854 -2.331298 99.625298 0.211635
Maximum 85.367203 -2.179322 100.006638 81.365089
Sigma (RMS) 0.002280 0.003601 0.012268 1.660576
Number of ASPECT records processed = 68624
Aspecting to RA/DEC : 85.35961914 -2.31921911
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 99847335.386440 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 85.360 DEC: -2.319
START TIME: SC 99810769.0027 = UT 01/03/96 05:12:49
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500099 9.927 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
812.997498 9.818 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1713.994629 0.277 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
3048.990479 0.263 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
6558.979004 0.695 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
8808.971680 0.337 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
12304.959961 0.551 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
14496.953125 0.345 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
18050.941406 0.364 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
20264.935547 0.409 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
23796.923828 0.453 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
26024.916016 0.458 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
29542.906250 0.475 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
31736.898438 0.461 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
35290.886719 0.486 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
40224.871094 0.477 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
41048.871094 0.438 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
43240.863281 0.489 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
46792.851562 0.448 1C2843 1 1 0 0 0 0 1 0 0 0 0 1 0 1 0 4 3
49000.843750 0.446 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
52536.835938 0.393 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
54760.828125 0.457 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
58280.816406 0.423 1C2843 1 1 0 0 0 0 1 0 0 0 0 1 0 1 0 4 3
60520.808594 0.433 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
64056.800781 0.432 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
66216.789062 0.443 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
70192.781250 0.410 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
71976.773438 0.416 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
75512.765625 0.407 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
77720.757812 0.423 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
81258.750000 0.235 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
83496.742188 0.469 FC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
85688.734375 5.276 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
85704.734375 81.365 3E03 1 1 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0
Attitude Records: 68624
Attitude Steps: 34
Maneuver ACM time: 32893.5 sec
Pointed ACM time: 52811.5 sec
-> Calculating aspect point100 99 count=1949 sum1=166638 sum2=179322 sum3=369799 100 100 count=153 sum1=13080.6 sum2=14077.6 sum3=29028.2 101 99 count=42 sum1=3591.04 sum2=3864.29 sum3=7969.09 108 104 count=1 sum1=85.572 sum2=92.059 sum3=189.729 109 113 count=3223 sum1=275860 sum2=296996 sum3=611296 109 114 count=42869 sum1=3.66909e+06 sum2=3.95047e+06 sum3=8.13089e+06 110 113 count=2959 sum1=253267 sum2=272669 sum3=561227 110 114 count=17426 sum1=1.49155e+06 sum2=1.60583e+06 sum3=3.3052e+06 1 out of 68623 points outside bin structure-> Euler angles: 85.59, 92.1516, 189.669
Interpolating 15 records in time interval 9.98119e+07 - 9.98125e+07 Interpolating 3 records in time interval 9.98522e+07 - 9.98522e+07 Interpolating 3 records in time interval 9.98522e+07 - 9.98522e+07 Interpolating 1 records in time interval 9.98964e+07 - 9.98965e+07 Interpolating 9 records in time interval 9.98965e+07 - 9.98965e+07 Interpolating 129 records in time interval 9.98965e+07 - 9.98965e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft960301_0512.0500",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft960301_0512.0500 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 1 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode Warning: ccdlist pattern 0 3 1 1 for S0 indicates 3-CCD mode in superframe 11510 Warning: ccdlist pattern 0 3 1 1 for S0 indicates 3-CCD mode in superframe 11510 Warning: ccdlist pattern 0 3 1 1 for S0 indicates 3-CCD mode in superframe 11510 No mode = 0 Faint = 1099072 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 1098048 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 17371 no. of SIS events found = 461900-> Standard Error Output From FTOOL frfread
coordinate error 1 256 coordinate error 0 0 coordinate error 0 0 coordinate error 432 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 243 coordinate error 0 0 coordinate error 0 0 coordinate error 96 0 coordinate error 0 0 coordinate error 0 0 coordinate error 96 0 coordinate error 0 12 coordinate error 24 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 48 0 coordinate error 3 0 coordinate error 384 0 coordinate error 0 0 coordinate error 24 0 coordinate error 1 256 coordinate error 0 6 coordinate error 3 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 12 coordinate error 0 0 coordinate error 3 0 coordinate error 384 0 coordinate error 0 0 coordinate error 0 0 coordinate error 384 0 coordinate error 0 0 coordinate error 0 0-> Removing the following files with NEVENTS=0
ft960301_0512_0500G200499.fits ft960301_0512_0500G200570L.fits ft960301_0512_0500G201570L.fits ft960301_0512_0500G201670H.fits ft960301_0512_0500G201770H.fits ft960301_0512_0500G201870H.fits ft960301_0512_0500G201970H.fits ft960301_0512_0500G202070H.fits ft960301_0512_0500G202499.fits ft960301_0512_0500G202670H.fits ft960301_0512_0500G202770H.fits ft960301_0512_0500G202870M.fits ft960301_0512_0500G202970M.fits ft960301_0512_0500G203070H.fits ft960301_0512_0500G203170H.fits ft960301_0512_0500G203270H.fits ft960301_0512_0500G203370H.fits ft960301_0512_0500G203670H.fits ft960301_0512_0500G203899.fits ft960301_0512_0500G204470L.fits ft960301_0512_0500G204570H.fits ft960301_0512_0500G204670H.fits ft960301_0512_0500G204770H.fits ft960301_0512_0500G204870H.fits ft960301_0512_0500G204970H.fits ft960301_0512_0500G205070H.fits ft960301_0512_0500G205770L.fits ft960301_0512_0500G205870H.fits ft960301_0512_0500G205970H.fits ft960301_0512_0500G206070H.fits ft960301_0512_0500G206170H.fits ft960301_0512_0500G206770H.fits ft960301_0512_0500G206870H.fits ft960301_0512_0500G206970H.fits ft960301_0512_0500G207070H.fits ft960301_0512_0500G207673H.fits ft960301_0512_0500G208170M.fits ft960301_0512_0500G208270H.fits ft960301_0512_0500G208370H.fits ft960301_0512_0500G208470H.fits ft960301_0512_0500G208570H.fits ft960301_0512_0500G208770H.fits ft960301_0512_0500G209070H.fits ft960301_0512_0500G209170H.fits ft960301_0512_0500G209270H.fits ft960301_0512_0500G209370H.fits ft960301_0512_0500G209670H.fits ft960301_0512_0500G211270M.fits ft960301_0512_0500G211370M.fits ft960301_0512_0500G211570M.fits ft960301_0512_0500G211770M.fits ft960301_0512_0500G211870M.fits ft960301_0512_0500G215270H.fits ft960301_0512_0500G216370H.fits ft960301_0512_0500G216870H.fits ft960301_0512_0500G217570M.fits ft960301_0512_0500G218570L.fits ft960301_0512_0500G300699.fits ft960301_0512_0500G301770L.fits ft960301_0512_0500G301870H.fits ft960301_0512_0500G301970H.fits ft960301_0512_0500G302070H.fits ft960301_0512_0500G302170H.fits ft960301_0512_0500G302270H.fits ft960301_0512_0500G302699.fits ft960301_0512_0500G302870H.fits ft960301_0512_0500G302970H.fits ft960301_0512_0500G303070M.fits ft960301_0512_0500G303170M.fits ft960301_0512_0500G303270H.fits ft960301_0512_0500G303370H.fits ft960301_0512_0500G303470H.fits ft960301_0512_0500G303570H.fits ft960301_0512_0500G303670H.fits ft960301_0512_0500G304099.fits ft960301_0512_0500G304670L.fits ft960301_0512_0500G304770H.fits ft960301_0512_0500G304870H.fits ft960301_0512_0500G304970H.fits ft960301_0512_0500G305070H.fits ft960301_0512_0500G305970L.fits ft960301_0512_0500G306070H.fits ft960301_0512_0500G306170H.fits ft960301_0512_0500G306270H.fits ft960301_0512_0500G306370H.fits ft960301_0512_0500G306470H.fits ft960301_0512_0500G306570H.fits ft960301_0512_0500G307070H.fits ft960301_0512_0500G307170H.fits ft960301_0512_0500G307270H.fits ft960301_0512_0500G307370H.fits ft960301_0512_0500G307773H.fits ft960301_0512_0500G308270M.fits ft960301_0512_0500G308370H.fits ft960301_0512_0500G308470H.fits ft960301_0512_0500G308570H.fits ft960301_0512_0500G308670H.fits ft960301_0512_0500G308770H.fits ft960301_0512_0500G309370H.fits ft960301_0512_0500G309470H.fits ft960301_0512_0500G309570H.fits ft960301_0512_0500G309670H.fits ft960301_0512_0500G309870H.fits ft960301_0512_0500G310270H.fits ft960301_0512_0500G312270M.fits ft960301_0512_0500G312370M.fits ft960301_0512_0500G312470M.fits ft960301_0512_0500G312570M.fits ft960301_0512_0500G312670M.fits ft960301_0512_0500G317670H.fits ft960301_0512_0500G317770H.fits ft960301_0512_0500G318370H.fits ft960301_0512_0500G318770H.fits ft960301_0512_0500G319270M.fits ft960301_0512_0500G320270L.fits ft960301_0512_0500S000399.fits ft960301_0512_0500S001399.fits ft960301_0512_0500S001901M.fits ft960301_0512_0500S002299.fits ft960301_0512_0500S003101L.fits ft960301_0512_0500S003499.fits ft960301_0512_0500S003701M.fits ft960301_0512_0500S003801H.fits ft960301_0512_0500S004501M.fits ft960301_0512_0500S100399.fits ft960301_0512_0500S101399.fits ft960301_0512_0500S101801M.fits ft960301_0512_0500S102199.fits ft960301_0512_0500S103001L.fits ft960301_0512_0500S103399.fits ft960301_0512_0500S103601M.fits ft960301_0512_0500S103701H.fits ft960301_0512_0500S104401M.fits-> Checking for empty GTI extensions
ft960301_0512_0500S000101H.fits[3] ft960301_0512_0500S000201M.fits[3] ft960301_0512_0500S000401L.fits[3] ft960301_0512_0500S000501L.fits[3] ft960301_0512_0500S000601L.fits[3] ft960301_0512_0500S000701H.fits[3] ft960301_0512_0500S000801M.fits[3] ft960301_0512_0500S000901L.fits[3] ft960301_0512_0500S001001L.fits[3] ft960301_0512_0500S001101L.fits[3] ft960301_0512_0500S001201H.fits[3] ft960301_0512_0500S001401H.fits[3] ft960301_0512_0500S001501H.fits[3] ft960301_0512_0500S001601H.fits[3] ft960301_0512_0500S001701H.fits[3] ft960301_0512_0500S001801H.fits[3] ft960301_0512_0500S002001M.fits[3] ft960301_0512_0500S002101H.fits[3] ft960301_0512_0500S002301H.fits[3] ft960301_0512_0500S002401M.fits[3] ft960301_0512_0500S002501L.fits[3] ft960301_0512_0500S002601L.fits[3] ft960301_0512_0500S002701L.fits[3] ft960301_0512_0500S002801H.fits[3] ft960301_0512_0500S002901M.fits[3] ft960301_0512_0500S003001L.fits[3] ft960301_0512_0500S003201L.fits[3] ft960301_0512_0500S003301H.fits[3] ft960301_0512_0500S003501H.fits[3] ft960301_0512_0500S003601M.fits[3] ft960301_0512_0500S003901H.fits[3] ft960301_0512_0500S004001M.fits[3] ft960301_0512_0500S004101H.fits[3] ft960301_0512_0500S004201M.fits[3] ft960301_0512_0500S004301L.fits[3] ft960301_0512_0500S004401M.fits[3] ft960301_0512_0500S004601M.fits[3] ft960301_0512_0500S004701L.fits[3] ft960301_0512_0500S004801M.fits[3] ft960301_0512_0500S004901H.fits[3] ft960301_0512_0500S005001H.fits[3] ft960301_0512_0500S005101H.fits[3] ft960301_0512_0500S005201H.fits[3] ft960301_0512_0500S005301H.fits[3] ft960301_0512_0500S005401M.fits[3] ft960301_0512_0500S005501L.fits[3] ft960301_0512_0500S005601M.fits[3] ft960301_0512_0500S005701L.fits[3] ft960301_0512_0500S005801M.fits[3] ft960301_0512_0500S005901M.fits[3] ft960301_0512_0500S006001M.fits[3] ft960301_0512_0500S006101H.fits[3] ft960301_0512_0500S006201M.fits[3] ft960301_0512_0500S006301H.fits[3] ft960301_0512_0500S006401M.fits[3] ft960301_0512_0500S006501H.fits[3] ft960301_0512_0500S006601M.fits[3] ft960301_0512_0500S006701H.fits[3] ft960301_0512_0500S006801M.fits[3] ft960301_0512_0500S006901L.fits[3] ft960301_0512_0500S007001M.fits[3]-> Merging GTIs from the following files:
ft960301_0512_0500S100101H.fits[3] ft960301_0512_0500S100201M.fits[3] ft960301_0512_0500S100401L.fits[3] ft960301_0512_0500S100501L.fits[3] ft960301_0512_0500S100601L.fits[3] ft960301_0512_0500S100701H.fits[3] ft960301_0512_0500S100801M.fits[3] ft960301_0512_0500S100901L.fits[3] ft960301_0512_0500S101001L.fits[3] ft960301_0512_0500S101101L.fits[3] ft960301_0512_0500S101201H.fits[3] ft960301_0512_0500S101401H.fits[3] ft960301_0512_0500S101501H.fits[3] ft960301_0512_0500S101601H.fits[3] ft960301_0512_0500S101701H.fits[3] ft960301_0512_0500S101901M.fits[3] ft960301_0512_0500S102001H.fits[3] ft960301_0512_0500S102201H.fits[3] ft960301_0512_0500S102301M.fits[3] ft960301_0512_0500S102401L.fits[3] ft960301_0512_0500S102501L.fits[3] ft960301_0512_0500S102601L.fits[3] ft960301_0512_0500S102701H.fits[3] ft960301_0512_0500S102801M.fits[3] ft960301_0512_0500S102901L.fits[3] ft960301_0512_0500S103101L.fits[3] ft960301_0512_0500S103201H.fits[3] ft960301_0512_0500S103401H.fits[3] ft960301_0512_0500S103501M.fits[3] ft960301_0512_0500S103801H.fits[3] ft960301_0512_0500S103901M.fits[3] ft960301_0512_0500S104001H.fits[3] ft960301_0512_0500S104101M.fits[3] ft960301_0512_0500S104201L.fits[3] ft960301_0512_0500S104301M.fits[3] ft960301_0512_0500S104501M.fits[3] ft960301_0512_0500S104601L.fits[3] ft960301_0512_0500S104701M.fits[3] ft960301_0512_0500S104801H.fits[3] ft960301_0512_0500S104901H.fits[3] ft960301_0512_0500S105001H.fits[3] ft960301_0512_0500S105101M.fits[3] ft960301_0512_0500S105201L.fits[3] ft960301_0512_0500S105301M.fits[3] ft960301_0512_0500S105401L.fits[3] ft960301_0512_0500S105501M.fits[3] ft960301_0512_0500S105601H.fits[3] ft960301_0512_0500S105701M.fits[3] ft960301_0512_0500S105801H.fits[3] ft960301_0512_0500S105901M.fits[3] ft960301_0512_0500S106001H.fits[3] ft960301_0512_0500S106101M.fits[3] ft960301_0512_0500S106201H.fits[3] ft960301_0512_0500S106301M.fits[3] ft960301_0512_0500S106401L.fits[3] ft960301_0512_0500S106501M.fits[3]-> Merging GTIs from the following files:
ft960301_0512_0500G200170H.fits[3] ft960301_0512_0500G200270M.fits[3] ft960301_0512_0500G200370M.fits[3] ft960301_0512_0500G200670L.fits[3] ft960301_0512_0500G200770L.fits[3] ft960301_0512_0500G200870H.fits[3] ft960301_0512_0500G200970H.fits[3] ft960301_0512_0500G201070H.fits[3] ft960301_0512_0500G201170H.fits[3] ft960301_0512_0500G201270M.fits[3] ft960301_0512_0500G201370M.fits[3] ft960301_0512_0500G201470L.fits[3] ft960301_0512_0500G202170H.fits[3] ft960301_0512_0500G202270H.fits[3] ft960301_0512_0500G202370H.fits[3] ft960301_0512_0500G202570H.fits[3] ft960301_0512_0500G203470H.fits[3] ft960301_0512_0500G203570H.fits[3] ft960301_0512_0500G203770H.fits[3] ft960301_0512_0500G203970H.fits[3] ft960301_0512_0500G204070M.fits[3] ft960301_0512_0500G204170M.fits[3] ft960301_0512_0500G204270L.fits[3] ft960301_0512_0500G204370L.fits[3] ft960301_0512_0500G205170H.fits[3] ft960301_0512_0500G205270H.fits[3] ft960301_0512_0500G205370M.fits[3] ft960301_0512_0500G205470M.fits[3] ft960301_0512_0500G205570L.fits[3] ft960301_0512_0500G205670L.fits[3] ft960301_0512_0500G206270H.fits[3] ft960301_0512_0500G206370H.fits[3] ft960301_0512_0500G206470H.fits[3] ft960301_0512_0500G206570H.fits[3] ft960301_0512_0500G206670H.fits[3] ft960301_0512_0500G207170H.fits[3] ft960301_0512_0500G207270H.fits[3] ft960301_0512_0500G207370H.fits[3] ft960301_0512_0500G207470H.fits[3] ft960301_0512_0500G207570H.fits[3] ft960301_0512_0500G207770H.fits[3] ft960301_0512_0500G207870M.fits[3] ft960301_0512_0500G207970M.fits[3] ft960301_0512_0500G208070M.fits[3] ft960301_0512_0500G208670H.fits[3] ft960301_0512_0500G208870H.fits[3] ft960301_0512_0500G208970H.fits[3] ft960301_0512_0500G209470H.fits[3] ft960301_0512_0500G209570H.fits[3] ft960301_0512_0500G209770H.fits[3] ft960301_0512_0500G209870M.fits[3] ft960301_0512_0500G209970H.fits[3] ft960301_0512_0500G210070H.fits[3] ft960301_0512_0500G210170H.fits[3] ft960301_0512_0500G210270H.fits[3] ft960301_0512_0500G210370H.fits[3] ft960301_0512_0500G210470H.fits[3] ft960301_0512_0500G210570M.fits[3] ft960301_0512_0500G210670M.fits[3] ft960301_0512_0500G210770M.fits[3] ft960301_0512_0500G210870M.fits[3] ft960301_0512_0500G210970L.fits[3] ft960301_0512_0500G211070L.fits[3] ft960301_0512_0500G211170M.fits[3] ft960301_0512_0500G211470M.fits[3] ft960301_0512_0500G211670M.fits[3] ft960301_0512_0500G211970M.fits[3] ft960301_0512_0500G212070M.fits[3] ft960301_0512_0500G212170M.fits[3] ft960301_0512_0500G212270M.fits[3] ft960301_0512_0500G212370L.fits[3] ft960301_0512_0500G212470L.fits[3] ft960301_0512_0500G212570M.fits[3] ft960301_0512_0500G212670M.fits[3] ft960301_0512_0500G212770M.fits[3] ft960301_0512_0500G212870M.fits[3] ft960301_0512_0500G212970M.fits[3] ft960301_0512_0500G213070M.fits[3] ft960301_0512_0500G213170M.fits[3] ft960301_0512_0500G213270M.fits[3] ft960301_0512_0500G213370H.fits[3] ft960301_0512_0500G213470H.fits[3] ft960301_0512_0500G213570H.fits[3] ft960301_0512_0500G213670H.fits[3] ft960301_0512_0500G213770H.fits[3] ft960301_0512_0500G213870H.fits[3] ft960301_0512_0500G213970M.fits[3] ft960301_0512_0500G214070M.fits[3] ft960301_0512_0500G214170L.fits[3] ft960301_0512_0500G214270L.fits[3] ft960301_0512_0500G214370M.fits[3] ft960301_0512_0500G214470M.fits[3] ft960301_0512_0500G214570M.fits[3] ft960301_0512_0500G214670M.fits[3] ft960301_0512_0500G214770L.fits[3] ft960301_0512_0500G214870M.fits[3] ft960301_0512_0500G214970M.fits[3] ft960301_0512_0500G215070M.fits[3] ft960301_0512_0500G215170M.fits[3] ft960301_0512_0500G215370H.fits[3] ft960301_0512_0500G215470H.fits[3] ft960301_0512_0500G215570H.fits[3] ft960301_0512_0500G215670H.fits[3] ft960301_0512_0500G215770H.fits[3] ft960301_0512_0500G215870H.fits[3] ft960301_0512_0500G215970H.fits[3] ft960301_0512_0500G216070M.fits[3] ft960301_0512_0500G216170M.fits[3] ft960301_0512_0500G216270H.fits[3] ft960301_0512_0500G216470H.fits[3] ft960301_0512_0500G216570H.fits[3] ft960301_0512_0500G216670M.fits[3] ft960301_0512_0500G216770M.fits[3] ft960301_0512_0500G216970H.fits[3] ft960301_0512_0500G217070H.fits[3] ft960301_0512_0500G217170H.fits[3] ft960301_0512_0500G217270M.fits[3] ft960301_0512_0500G217370M.fits[3] ft960301_0512_0500G217470M.fits[3] ft960301_0512_0500G217670M.fits[3] ft960301_0512_0500G217770M.fits[3] ft960301_0512_0500G217870H.fits[3] ft960301_0512_0500G217970H.fits[3] ft960301_0512_0500G218070H.fits[3] ft960301_0512_0500G218170H.fits[3] ft960301_0512_0500G218270M.fits[3] ft960301_0512_0500G218370M.fits[3] ft960301_0512_0500G218470L.fits[3] ft960301_0512_0500G218670L.fits[3] ft960301_0512_0500G218770L.fits[3] ft960301_0512_0500G218870M.fits[3] ft960301_0512_0500G218970M.fits[3] ft960301_0512_0500G219070M.fits[3] ft960301_0512_0500G219170M.fits[3]-> Merging GTIs from the following files:
ft960301_0512_0500G300170H.fits[3] ft960301_0512_0500G300270H.fits[3] ft960301_0512_0500G300370H.fits[3] ft960301_0512_0500G300470M.fits[3] ft960301_0512_0500G300570M.fits[3] ft960301_0512_0500G300770L.fits[3] ft960301_0512_0500G300870L.fits[3] ft960301_0512_0500G300970L.fits[3] ft960301_0512_0500G301070H.fits[3] ft960301_0512_0500G301170H.fits[3] ft960301_0512_0500G301270H.fits[3] ft960301_0512_0500G301370H.fits[3] ft960301_0512_0500G301470M.fits[3] ft960301_0512_0500G301570M.fits[3] ft960301_0512_0500G301670L.fits[3] ft960301_0512_0500G302370H.fits[3] ft960301_0512_0500G302470H.fits[3] ft960301_0512_0500G302570H.fits[3] ft960301_0512_0500G302770H.fits[3] ft960301_0512_0500G303770H.fits[3] ft960301_0512_0500G303870H.fits[3] ft960301_0512_0500G303970H.fits[3] ft960301_0512_0500G304170H.fits[3] ft960301_0512_0500G304270M.fits[3] ft960301_0512_0500G304370M.fits[3] ft960301_0512_0500G304470L.fits[3] ft960301_0512_0500G304570L.fits[3] ft960301_0512_0500G305170H.fits[3] ft960301_0512_0500G305270H.fits[3] ft960301_0512_0500G305370H.fits[3] ft960301_0512_0500G305470H.fits[3] ft960301_0512_0500G305570M.fits[3] ft960301_0512_0500G305670M.fits[3] ft960301_0512_0500G305770L.fits[3] ft960301_0512_0500G305870L.fits[3] ft960301_0512_0500G306670H.fits[3] ft960301_0512_0500G306770H.fits[3] ft960301_0512_0500G306870H.fits[3] ft960301_0512_0500G306970H.fits[3] ft960301_0512_0500G307470H.fits[3] ft960301_0512_0500G307570H.fits[3] ft960301_0512_0500G307670H.fits[3] ft960301_0512_0500G307870H.fits[3] ft960301_0512_0500G307970M.fits[3] ft960301_0512_0500G308070M.fits[3] ft960301_0512_0500G308170M.fits[3] ft960301_0512_0500G308870H.fits[3] ft960301_0512_0500G308970H.fits[3] ft960301_0512_0500G309070H.fits[3] ft960301_0512_0500G309170H.fits[3] ft960301_0512_0500G309270H.fits[3] ft960301_0512_0500G309770H.fits[3] ft960301_0512_0500G309970H.fits[3] ft960301_0512_0500G310070M.fits[3] ft960301_0512_0500G310170H.fits[3] ft960301_0512_0500G310370H.fits[3] ft960301_0512_0500G310470H.fits[3] ft960301_0512_0500G310570H.fits[3] ft960301_0512_0500G310670H.fits[3] ft960301_0512_0500G310770H.fits[3] ft960301_0512_0500G310870H.fits[3] ft960301_0512_0500G310970H.fits[3] ft960301_0512_0500G311070H.fits[3] ft960301_0512_0500G311170H.fits[3] ft960301_0512_0500G311270H.fits[3] ft960301_0512_0500G311370M.fits[3] ft960301_0512_0500G311470M.fits[3] ft960301_0512_0500G311570M.fits[3] ft960301_0512_0500G311670M.fits[3] ft960301_0512_0500G311770M.fits[3] ft960301_0512_0500G311870M.fits[3] ft960301_0512_0500G311970L.fits[3] ft960301_0512_0500G312070L.fits[3] ft960301_0512_0500G312170M.fits[3] ft960301_0512_0500G312770M.fits[3] ft960301_0512_0500G312870M.fits[3] ft960301_0512_0500G312970M.fits[3] ft960301_0512_0500G313070M.fits[3] ft960301_0512_0500G313170M.fits[3] ft960301_0512_0500G313270M.fits[3] ft960301_0512_0500G313370M.fits[3] ft960301_0512_0500G313470M.fits[3] ft960301_0512_0500G313570M.fits[3] ft960301_0512_0500G313670L.fits[3] ft960301_0512_0500G313770L.fits[3] ft960301_0512_0500G313870L.fits[3] ft960301_0512_0500G313970L.fits[3] ft960301_0512_0500G314070M.fits[3] ft960301_0512_0500G314170M.fits[3] ft960301_0512_0500G314270M.fits[3] ft960301_0512_0500G314370M.fits[3] ft960301_0512_0500G314470H.fits[3] ft960301_0512_0500G314570H.fits[3] ft960301_0512_0500G314670H.fits[3] ft960301_0512_0500G314770H.fits[3] ft960301_0512_0500G314870H.fits[3] ft960301_0512_0500G314970H.fits[3] ft960301_0512_0500G315070H.fits[3] ft960301_0512_0500G315170H.fits[3] ft960301_0512_0500G315270M.fits[3] ft960301_0512_0500G315370M.fits[3] ft960301_0512_0500G315470L.fits[3] ft960301_0512_0500G315570L.fits[3] ft960301_0512_0500G315670M.fits[3] ft960301_0512_0500G315770M.fits[3] ft960301_0512_0500G315870M.fits[3] ft960301_0512_0500G315970M.fits[3] ft960301_0512_0500G316070M.fits[3] ft960301_0512_0500G316170M.fits[3] ft960301_0512_0500G316270L.fits[3] ft960301_0512_0500G316370M.fits[3] ft960301_0512_0500G316470M.fits[3] ft960301_0512_0500G316570M.fits[3] ft960301_0512_0500G316670M.fits[3] ft960301_0512_0500G316770H.fits[3] ft960301_0512_0500G316870H.fits[3] ft960301_0512_0500G316970H.fits[3] ft960301_0512_0500G317070H.fits[3] ft960301_0512_0500G317170H.fits[3] ft960301_0512_0500G317270H.fits[3] ft960301_0512_0500G317370M.fits[3] ft960301_0512_0500G317470M.fits[3] ft960301_0512_0500G317570H.fits[3] ft960301_0512_0500G317870H.fits[3] ft960301_0512_0500G317970H.fits[3] ft960301_0512_0500G318070H.fits[3] ft960301_0512_0500G318170M.fits[3] ft960301_0512_0500G318270M.fits[3] ft960301_0512_0500G318470H.fits[3] ft960301_0512_0500G318570H.fits[3] ft960301_0512_0500G318670H.fits[3] ft960301_0512_0500G318870H.fits[3] ft960301_0512_0500G318970M.fits[3] ft960301_0512_0500G319070M.fits[3] ft960301_0512_0500G319170M.fits[3] ft960301_0512_0500G319370M.fits[3] ft960301_0512_0500G319470M.fits[3] ft960301_0512_0500G319570H.fits[3] ft960301_0512_0500G319670H.fits[3] ft960301_0512_0500G319770H.fits[3] ft960301_0512_0500G319870H.fits[3] ft960301_0512_0500G319970M.fits[3] ft960301_0512_0500G320070M.fits[3] ft960301_0512_0500G320170L.fits[3] ft960301_0512_0500G320370L.fits[3] ft960301_0512_0500G320470L.fits[3] ft960301_0512_0500G320570M.fits[3] ft960301_0512_0500G320670M.fits[3] ft960301_0512_0500G320770M.fits[3] ft960301_0512_0500G320870M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 3 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 3 photon cnt = 4 GISSORTSPLIT:LO:g200470h.prelist merge count = 4 photon cnt = 8 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200770h.prelist merge count = 21 photon cnt = 26341 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g200970h.prelist merge count = 7 photon cnt = 29 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202070h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g202270h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g202370h.prelist merge count = 2 photon cnt = 8 GISSORTSPLIT:LO:g202470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202570h.prelist merge count = 1 photon cnt = 1713 GISSORTSPLIT:LO:g202670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g200270l.prelist merge count = 2 photon cnt = 7 GISSORTSPLIT:LO:g200370l.prelist merge count = 1 photon cnt = 58 GISSORTSPLIT:LO:g200470l.prelist merge count = 9 photon cnt = 6757 GISSORTSPLIT:LO:g200570l.prelist merge count = 4 photon cnt = 260 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g200370m.prelist merge count = 2 photon cnt = 4 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200570m.prelist merge count = 2 photon cnt = 7 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 236 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 30 GISSORTSPLIT:LO:g200870m.prelist merge count = 22 photon cnt = 21476 GISSORTSPLIT:LO:g200970m.prelist merge count = 15 photon cnt = 379 GISSORTSPLIT:LO:g201070m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g201170m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g201270m.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g201370m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g201470m.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g201570m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g201670m.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g201770m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g201870m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:Total filenames split = 134 GISSORTSPLIT:LO:Total split file cnt = 50 GISSORTSPLIT:LO:End program-> Creating ad24043000g200170h.unf
---- cmerge: version 1.5 ---- A total of 21 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G200170H.fits 2 -- ft960301_0512_0500G201170H.fits 3 -- ft960301_0512_0500G202370H.fits 4 -- ft960301_0512_0500G202570H.fits 5 -- ft960301_0512_0500G203770H.fits 6 -- ft960301_0512_0500G203970H.fits 7 -- ft960301_0512_0500G205270H.fits 8 -- ft960301_0512_0500G206570H.fits 9 -- ft960301_0512_0500G207570H.fits 10 -- ft960301_0512_0500G208970H.fits 11 -- ft960301_0512_0500G209770H.fits 12 -- ft960301_0512_0500G210270H.fits 13 -- ft960301_0512_0500G210470H.fits 14 -- ft960301_0512_0500G213670H.fits 15 -- ft960301_0512_0500G213870H.fits 16 -- ft960301_0512_0500G215570H.fits 17 -- ft960301_0512_0500G215770H.fits 18 -- ft960301_0512_0500G215970H.fits 19 -- ft960301_0512_0500G216570H.fits 20 -- ft960301_0512_0500G217170H.fits 21 -- ft960301_0512_0500G218170H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G200170H.fits 2 -- ft960301_0512_0500G201170H.fits 3 -- ft960301_0512_0500G202370H.fits 4 -- ft960301_0512_0500G202570H.fits 5 -- ft960301_0512_0500G203770H.fits 6 -- ft960301_0512_0500G203970H.fits 7 -- ft960301_0512_0500G205270H.fits 8 -- ft960301_0512_0500G206570H.fits 9 -- ft960301_0512_0500G207570H.fits 10 -- ft960301_0512_0500G208970H.fits 11 -- ft960301_0512_0500G209770H.fits 12 -- ft960301_0512_0500G210270H.fits 13 -- ft960301_0512_0500G210470H.fits 14 -- ft960301_0512_0500G213670H.fits 15 -- ft960301_0512_0500G213870H.fits 16 -- ft960301_0512_0500G215570H.fits 17 -- ft960301_0512_0500G215770H.fits 18 -- ft960301_0512_0500G215970H.fits 19 -- ft960301_0512_0500G216570H.fits 20 -- ft960301_0512_0500G217170H.fits 21 -- ft960301_0512_0500G218170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000g200270m.unf
---- cmerge: version 1.5 ---- A total of 22 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G200370M.fits 2 -- ft960301_0512_0500G201370M.fits 3 -- ft960301_0512_0500G204170M.fits 4 -- ft960301_0512_0500G205470M.fits 5 -- ft960301_0512_0500G207970M.fits 6 -- ft960301_0512_0500G209870M.fits 7 -- ft960301_0512_0500G210670M.fits 8 -- ft960301_0512_0500G210870M.fits 9 -- ft960301_0512_0500G212070M.fits 10 -- ft960301_0512_0500G212270M.fits 11 -- ft960301_0512_0500G212870M.fits 12 -- ft960301_0512_0500G213070M.fits 13 -- ft960301_0512_0500G213270M.fits 14 -- ft960301_0512_0500G214070M.fits 15 -- ft960301_0512_0500G214670M.fits 16 -- ft960301_0512_0500G215170M.fits 17 -- ft960301_0512_0500G216170M.fits 18 -- ft960301_0512_0500G216770M.fits 19 -- ft960301_0512_0500G217370M.fits 20 -- ft960301_0512_0500G217770M.fits 21 -- ft960301_0512_0500G218370M.fits 22 -- ft960301_0512_0500G219170M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G200370M.fits 2 -- ft960301_0512_0500G201370M.fits 3 -- ft960301_0512_0500G204170M.fits 4 -- ft960301_0512_0500G205470M.fits 5 -- ft960301_0512_0500G207970M.fits 6 -- ft960301_0512_0500G209870M.fits 7 -- ft960301_0512_0500G210670M.fits 8 -- ft960301_0512_0500G210870M.fits 9 -- ft960301_0512_0500G212070M.fits 10 -- ft960301_0512_0500G212270M.fits 11 -- ft960301_0512_0500G212870M.fits 12 -- ft960301_0512_0500G213070M.fits 13 -- ft960301_0512_0500G213270M.fits 14 -- ft960301_0512_0500G214070M.fits 15 -- ft960301_0512_0500G214670M.fits 16 -- ft960301_0512_0500G215170M.fits 17 -- ft960301_0512_0500G216170M.fits 18 -- ft960301_0512_0500G216770M.fits 19 -- ft960301_0512_0500G217370M.fits 20 -- ft960301_0512_0500G217770M.fits 21 -- ft960301_0512_0500G218370M.fits 22 -- ft960301_0512_0500G219170M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000g200370l.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G200770L.fits 2 -- ft960301_0512_0500G204270L.fits 3 -- ft960301_0512_0500G205570L.fits 4 -- ft960301_0512_0500G211070L.fits 5 -- ft960301_0512_0500G212470L.fits 6 -- ft960301_0512_0500G214270L.fits 7 -- ft960301_0512_0500G214770L.fits 8 -- ft960301_0512_0500G218470L.fits 9 -- ft960301_0512_0500G218770L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G200770L.fits 2 -- ft960301_0512_0500G204270L.fits 3 -- ft960301_0512_0500G205570L.fits 4 -- ft960301_0512_0500G211070L.fits 5 -- ft960301_0512_0500G212470L.fits 6 -- ft960301_0512_0500G214270L.fits 7 -- ft960301_0512_0500G214770L.fits 8 -- ft960301_0512_0500G218470L.fits 9 -- ft960301_0512_0500G218770L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960301_0512_0500G207770H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G207770H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G207770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000379 events
ft960301_0512_0500G200270M.fits ft960301_0512_0500G201270M.fits ft960301_0512_0500G204070M.fits ft960301_0512_0500G205370M.fits ft960301_0512_0500G207870M.fits ft960301_0512_0500G210570M.fits ft960301_0512_0500G212770M.fits ft960301_0512_0500G213970M.fits ft960301_0512_0500G214570M.fits ft960301_0512_0500G215070M.fits ft960301_0512_0500G216070M.fits ft960301_0512_0500G216670M.fits ft960301_0512_0500G217270M.fits ft960301_0512_0500G218270M.fits ft960301_0512_0500G219070M.fits-> Ignoring the following files containing 000000260 events
ft960301_0512_0500G201470L.fits ft960301_0512_0500G210970L.fits ft960301_0512_0500G212370L.fits ft960301_0512_0500G214170L.fits-> Ignoring the following files containing 000000236 events
ft960301_0512_0500G213170M.fits-> Ignoring the following files containing 000000058 events
ft960301_0512_0500G218670L.fits-> Ignoring the following files containing 000000030 events
ft960301_0512_0500G212170M.fits-> Ignoring the following files containing 000000029 events
ft960301_0512_0500G201070H.fits ft960301_0512_0500G210170H.fits ft960301_0512_0500G213570H.fits ft960301_0512_0500G215470H.fits ft960301_0512_0500G216470H.fits ft960301_0512_0500G217070H.fits ft960301_0512_0500G218070H.fits-> Ignoring the following files containing 000000020 events
ft960301_0512_0500G214870M.fits-> Ignoring the following files containing 000000020 events
ft960301_0512_0500G218870M.fits-> Ignoring the following files containing 000000019 events
ft960301_0512_0500G218970M.fits-> Ignoring the following files containing 000000019 events
ft960301_0512_0500G214370M.fits-> Ignoring the following files containing 000000019 events
ft960301_0512_0500G200670L.fits-> Ignoring the following files containing 000000018 events
ft960301_0512_0500G212670M.fits-> Ignoring the following files containing 000000018 events
ft960301_0512_0500G212970M.fits-> Ignoring the following files containing 000000017 events
ft960301_0512_0500G214470M.fits-> Ignoring the following files containing 000000016 events
ft960301_0512_0500G212570M.fits-> Ignoring the following files containing 000000014 events
ft960301_0512_0500G213470H.fits-> Ignoring the following files containing 000000013 events
ft960301_0512_0500G213370H.fits-> Ignoring the following files containing 000000011 events
ft960301_0512_0500G214970M.fits-> Ignoring the following files containing 000000010 events
ft960301_0512_0500G210770M.fits-> Ignoring the following files containing 000000008 events
ft960301_0512_0500G207370H.fits ft960301_0512_0500G209570H.fits-> Ignoring the following files containing 000000008 events
ft960301_0512_0500G211170M.fits-> Ignoring the following files containing 000000008 events
ft960301_0512_0500G202270H.fits ft960301_0512_0500G205170H.fits ft960301_0512_0500G206470H.fits ft960301_0512_0500G208870H.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500G211970M.fits ft960301_0512_0500G217670M.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500G204370L.fits ft960301_0512_0500G205670L.fits-> Ignoring the following files containing 000000006 events
ft960301_0512_0500G213770H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G216970H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G215870H.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500G200870H.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500G208070M.fits ft960301_0512_0500G217470M.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500G202170H.fits ft960301_0512_0500G203570H.fits ft960301_0512_0500G206370H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G207270H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G203470H.fits ft960301_0512_0500G206270H.fits ft960301_0512_0500G208670H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G215670H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G207470H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G217970H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G217870H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G210070H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G216270H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G206670H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G211470M.fits ft960301_0512_0500G211670M.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G207170H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G210370H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G209470H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G209970H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G200970H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G215370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300470h.prelist merge count = 4 photon cnt = 8 GISSORTSPLIT:LO:g300570h.prelist merge count = 5 photon cnt = 7 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301670h.prelist merge count = 27 photon cnt = 26001 GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301870h.prelist merge count = 6 photon cnt = 25 GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g302070h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g302170h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g302270h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g302370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g302670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302770h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g302970h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g303070h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g303170h.prelist merge count = 2 photon cnt = 12 GISSORTSPLIT:LO:g303270h.prelist merge count = 1 photon cnt = 1623 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 25 GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370l.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300470l.prelist merge count = 1 photon cnt = 50 GISSORTSPLIT:LO:g300570l.prelist merge count = 1 photon cnt = 70 GISSORTSPLIT:LO:g300670l.prelist merge count = 10 photon cnt = 6175 GISSORTSPLIT:LO:g300770l.prelist merge count = 4 photon cnt = 211 GISSORTSPLIT:LO:g300170m.prelist merge count = 2 photon cnt = 12 GISSORTSPLIT:LO:g300270m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g300370m.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 31 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 34 GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g300970m.prelist merge count = 24 photon cnt = 21040 GISSORTSPLIT:LO:g301070m.prelist merge count = 15 photon cnt = 344 GISSORTSPLIT:LO:g301170m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g301270m.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g301370m.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g301470m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g301570m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g301670m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g301770m.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g301870m.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g301970m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g302070m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:Total filenames split = 150 GISSORTSPLIT:LO:Total split file cnt = 59 GISSORTSPLIT:LO:End program-> Creating ad24043000g300170h.unf
---- cmerge: version 1.5 ---- A total of 27 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G300170H.fits 2 -- ft960301_0512_0500G300370H.fits 3 -- ft960301_0512_0500G301370H.fits 4 -- ft960301_0512_0500G302570H.fits 5 -- ft960301_0512_0500G302770H.fits 6 -- ft960301_0512_0500G303970H.fits 7 -- ft960301_0512_0500G304170H.fits 8 -- ft960301_0512_0500G305470H.fits 9 -- ft960301_0512_0500G306770H.fits 10 -- ft960301_0512_0500G307670H.fits 11 -- ft960301_0512_0500G309070H.fits 12 -- ft960301_0512_0500G309970H.fits 13 -- ft960301_0512_0500G310470H.fits 14 -- ft960301_0512_0500G310670H.fits 15 -- ft960301_0512_0500G310870H.fits 16 -- ft960301_0512_0500G311070H.fits 17 -- ft960301_0512_0500G311270H.fits 18 -- ft960301_0512_0500G314770H.fits 19 -- ft960301_0512_0500G314970H.fits 20 -- ft960301_0512_0500G315170H.fits 21 -- ft960301_0512_0500G317070H.fits 22 -- ft960301_0512_0500G317270H.fits 23 -- ft960301_0512_0500G317870H.fits 24 -- ft960301_0512_0500G318070H.fits 25 -- ft960301_0512_0500G318670H.fits 26 -- ft960301_0512_0500G318870H.fits 27 -- ft960301_0512_0500G319870H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G300170H.fits 2 -- ft960301_0512_0500G300370H.fits 3 -- ft960301_0512_0500G301370H.fits 4 -- ft960301_0512_0500G302570H.fits 5 -- ft960301_0512_0500G302770H.fits 6 -- ft960301_0512_0500G303970H.fits 7 -- ft960301_0512_0500G304170H.fits 8 -- ft960301_0512_0500G305470H.fits 9 -- ft960301_0512_0500G306770H.fits 10 -- ft960301_0512_0500G307670H.fits 11 -- ft960301_0512_0500G309070H.fits 12 -- ft960301_0512_0500G309970H.fits 13 -- ft960301_0512_0500G310470H.fits 14 -- ft960301_0512_0500G310670H.fits 15 -- ft960301_0512_0500G310870H.fits 16 -- ft960301_0512_0500G311070H.fits 17 -- ft960301_0512_0500G311270H.fits 18 -- ft960301_0512_0500G314770H.fits 19 -- ft960301_0512_0500G314970H.fits 20 -- ft960301_0512_0500G315170H.fits 21 -- ft960301_0512_0500G317070H.fits 22 -- ft960301_0512_0500G317270H.fits 23 -- ft960301_0512_0500G317870H.fits 24 -- ft960301_0512_0500G318070H.fits 25 -- ft960301_0512_0500G318670H.fits 26 -- ft960301_0512_0500G318870H.fits 27 -- ft960301_0512_0500G319870H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000g300270m.unf
---- cmerge: version 1.5 ---- A total of 24 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G300570M.fits 2 -- ft960301_0512_0500G301570M.fits 3 -- ft960301_0512_0500G304370M.fits 4 -- ft960301_0512_0500G305670M.fits 5 -- ft960301_0512_0500G308070M.fits 6 -- ft960301_0512_0500G310070M.fits 7 -- ft960301_0512_0500G311470M.fits 8 -- ft960301_0512_0500G311670M.fits 9 -- ft960301_0512_0500G311870M.fits 10 -- ft960301_0512_0500G312870M.fits 11 -- ft960301_0512_0500G313070M.fits 12 -- ft960301_0512_0500G313370M.fits 13 -- ft960301_0512_0500G313570M.fits 14 -- ft960301_0512_0500G314370M.fits 15 -- ft960301_0512_0500G315370M.fits 16 -- ft960301_0512_0500G315970M.fits 17 -- ft960301_0512_0500G316170M.fits 18 -- ft960301_0512_0500G316670M.fits 19 -- ft960301_0512_0500G317470M.fits 20 -- ft960301_0512_0500G318270M.fits 21 -- ft960301_0512_0500G319070M.fits 22 -- ft960301_0512_0500G319470M.fits 23 -- ft960301_0512_0500G320070M.fits 24 -- ft960301_0512_0500G320870M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G300570M.fits 2 -- ft960301_0512_0500G301570M.fits 3 -- ft960301_0512_0500G304370M.fits 4 -- ft960301_0512_0500G305670M.fits 5 -- ft960301_0512_0500G308070M.fits 6 -- ft960301_0512_0500G310070M.fits 7 -- ft960301_0512_0500G311470M.fits 8 -- ft960301_0512_0500G311670M.fits 9 -- ft960301_0512_0500G311870M.fits 10 -- ft960301_0512_0500G312870M.fits 11 -- ft960301_0512_0500G313070M.fits 12 -- ft960301_0512_0500G313370M.fits 13 -- ft960301_0512_0500G313570M.fits 14 -- ft960301_0512_0500G314370M.fits 15 -- ft960301_0512_0500G315370M.fits 16 -- ft960301_0512_0500G315970M.fits 17 -- ft960301_0512_0500G316170M.fits 18 -- ft960301_0512_0500G316670M.fits 19 -- ft960301_0512_0500G317470M.fits 20 -- ft960301_0512_0500G318270M.fits 21 -- ft960301_0512_0500G319070M.fits 22 -- ft960301_0512_0500G319470M.fits 23 -- ft960301_0512_0500G320070M.fits 24 -- ft960301_0512_0500G320870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000g300370l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G300970L.fits 2 -- ft960301_0512_0500G304470L.fits 3 -- ft960301_0512_0500G305770L.fits 4 -- ft960301_0512_0500G312070L.fits 5 -- ft960301_0512_0500G313770L.fits 6 -- ft960301_0512_0500G313970L.fits 7 -- ft960301_0512_0500G315570L.fits 8 -- ft960301_0512_0500G316270L.fits 9 -- ft960301_0512_0500G320170L.fits 10 -- ft960301_0512_0500G320470L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G300970L.fits 2 -- ft960301_0512_0500G304470L.fits 3 -- ft960301_0512_0500G305770L.fits 4 -- ft960301_0512_0500G312070L.fits 5 -- ft960301_0512_0500G313770L.fits 6 -- ft960301_0512_0500G313970L.fits 7 -- ft960301_0512_0500G315570L.fits 8 -- ft960301_0512_0500G316270L.fits 9 -- ft960301_0512_0500G320170L.fits 10 -- ft960301_0512_0500G320470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960301_0512_0500G307870H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500G307870H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500G307870H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000344 events
ft960301_0512_0500G300470M.fits ft960301_0512_0500G301470M.fits ft960301_0512_0500G304270M.fits ft960301_0512_0500G305570M.fits ft960301_0512_0500G307970M.fits ft960301_0512_0500G311370M.fits ft960301_0512_0500G314270M.fits ft960301_0512_0500G315270M.fits ft960301_0512_0500G315870M.fits ft960301_0512_0500G316570M.fits ft960301_0512_0500G317370M.fits ft960301_0512_0500G318170M.fits ft960301_0512_0500G318970M.fits ft960301_0512_0500G319970M.fits ft960301_0512_0500G320770M.fits-> Ignoring the following files containing 000000211 events
ft960301_0512_0500G301670L.fits ft960301_0512_0500G311970L.fits ft960301_0512_0500G313670L.fits ft960301_0512_0500G315470L.fits-> Ignoring the following files containing 000000070 events
ft960301_0512_0500G313870L.fits-> Ignoring the following files containing 000000050 events
ft960301_0512_0500G320370L.fits-> Ignoring the following files containing 000000034 events
ft960301_0512_0500G316070M.fits-> Ignoring the following files containing 000000031 events
ft960301_0512_0500G313470M.fits-> Ignoring the following files containing 000000025 events
ft960301_0512_0500G301270H.fits ft960301_0512_0500G310370H.fits ft960301_0512_0500G314670H.fits ft960301_0512_0500G316970H.fits ft960301_0512_0500G318570H.fits ft960301_0512_0500G319770H.fits-> Ignoring the following files containing 000000025 events
ft960301_0512_0500G300870L.fits-> Ignoring the following files containing 000000020 events
ft960301_0512_0500G314170M.fits-> Ignoring the following files containing 000000019 events
ft960301_0512_0500G313170M.fits-> Ignoring the following files containing 000000019 events
ft960301_0512_0500G320670M.fits-> Ignoring the following files containing 000000018 events
ft960301_0512_0500G316470M.fits-> Ignoring the following files containing 000000017 events
ft960301_0512_0500G312970M.fits-> Ignoring the following files containing 000000017 events
ft960301_0512_0500G320570M.fits-> Ignoring the following files containing 000000017 events
ft960301_0512_0500G314070M.fits-> Ignoring the following files containing 000000016 events
ft960301_0512_0500G316370M.fits-> Ignoring the following files containing 000000015 events
ft960301_0512_0500G313270M.fits-> Ignoring the following files containing 000000014 events
ft960301_0512_0500G315770M.fits-> Ignoring the following files containing 000000014 events
ft960301_0512_0500G315670M.fits-> Ignoring the following files containing 000000012 events
ft960301_0512_0500G306870H.fits ft960301_0512_0500G309270H.fits-> Ignoring the following files containing 000000012 events
ft960301_0512_0500G311570M.fits-> Ignoring the following files containing 000000012 events
ft960301_0512_0500G308170M.fits ft960301_0512_0500G319170M.fits-> Ignoring the following files containing 000000011 events
ft960301_0512_0500G311770M.fits-> Ignoring the following files containing 000000009 events
ft960301_0512_0500G314570H.fits-> Ignoring the following files containing 000000008 events
ft960301_0512_0500G302370H.fits ft960301_0512_0500G303770H.fits ft960301_0512_0500G305270H.fits ft960301_0512_0500G308870H.fits-> Ignoring the following files containing 000000008 events
ft960301_0512_0500G312170M.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500G317170H.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500G314870H.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500G302470H.fits ft960301_0512_0500G303870H.fits ft960301_0512_0500G305370H.fits ft960301_0512_0500G306670H.fits ft960301_0512_0500G308970H.fits-> Ignoring the following files containing 000000006 events
ft960301_0512_0500G300270H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G314470H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G310970H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G311170H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G315070H.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G312770M.fits ft960301_0512_0500G319370M.fits-> Ignoring the following files containing 000000005 events
ft960301_0512_0500G304570L.fits ft960301_0512_0500G305870L.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500G301170H.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500G301070H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G319570H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G310770H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G309170H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G317970H.fits-> Ignoring the following files containing 000000003 events
ft960301_0512_0500G310570H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G306970H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G310170H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500G307570H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G316870H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G316770H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G318470H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G319670H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G317570H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G305170H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G300770L.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G307470H.fits-> Ignoring the following files containing 000000001 events
ft960301_0512_0500G309770H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 144 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 45 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 15 photon cnt = 72920 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 1 photon cnt = 2 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 1 photon cnt = 4 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 4 photon cnt = 8601 SIS0SORTSPLIT:LO:s000701h.prelist merge count = 1 photon cnt = 256 SIS0SORTSPLIT:LO:s000801l.prelist merge count = 9 photon cnt = 20489 SIS0SORTSPLIT:LO:s000901l.prelist merge count = 4 photon cnt = 3810 SIS0SORTSPLIT:LO:s001001l.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:s001101l.prelist merge count = 2 photon cnt = 152 SIS0SORTSPLIT:LO:s001201m.prelist merge count = 18 photon cnt = 64970 SIS0SORTSPLIT:LO:s001301m.prelist merge count = 1 photon cnt = 15 SIS0SORTSPLIT:LO:s001401m.prelist merge count = 2 photon cnt = 4664 SIS0SORTSPLIT:LO:Total filenames split = 61 SIS0SORTSPLIT:LO:Total split file cnt = 14 SIS0SORTSPLIT:LO:End program-> Creating ad24043000s000101h.unf
---- cmerge: version 1.5 ---- A total of 15 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S001701H.fits 2 -- ft960301_0512_0500S002101H.fits 3 -- ft960301_0512_0500S002301H.fits 4 -- ft960301_0512_0500S002801H.fits 5 -- ft960301_0512_0500S003301H.fits 6 -- ft960301_0512_0500S003501H.fits 7 -- ft960301_0512_0500S003901H.fits 8 -- ft960301_0512_0500S004101H.fits 9 -- ft960301_0512_0500S004901H.fits 10 -- ft960301_0512_0500S005101H.fits 11 -- ft960301_0512_0500S005301H.fits 12 -- ft960301_0512_0500S006101H.fits 13 -- ft960301_0512_0500S006301H.fits 14 -- ft960301_0512_0500S006501H.fits 15 -- ft960301_0512_0500S006701H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S001701H.fits 2 -- ft960301_0512_0500S002101H.fits 3 -- ft960301_0512_0500S002301H.fits 4 -- ft960301_0512_0500S002801H.fits 5 -- ft960301_0512_0500S003301H.fits 6 -- ft960301_0512_0500S003501H.fits 7 -- ft960301_0512_0500S003901H.fits 8 -- ft960301_0512_0500S004101H.fits 9 -- ft960301_0512_0500S004901H.fits 10 -- ft960301_0512_0500S005101H.fits 11 -- ft960301_0512_0500S005301H.fits 12 -- ft960301_0512_0500S006101H.fits 13 -- ft960301_0512_0500S006301H.fits 14 -- ft960301_0512_0500S006501H.fits 15 -- ft960301_0512_0500S006701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s000201m.unf
---- cmerge: version 1.5 ---- A total of 18 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S002001M.fits 2 -- ft960301_0512_0500S002401M.fits 3 -- ft960301_0512_0500S002901M.fits 4 -- ft960301_0512_0500S003601M.fits 5 -- ft960301_0512_0500S004001M.fits 6 -- ft960301_0512_0500S004201M.fits 7 -- ft960301_0512_0500S004401M.fits 8 -- ft960301_0512_0500S004601M.fits 9 -- ft960301_0512_0500S004801M.fits 10 -- ft960301_0512_0500S005401M.fits 11 -- ft960301_0512_0500S005601M.fits 12 -- ft960301_0512_0500S005801M.fits 13 -- ft960301_0512_0500S006001M.fits 14 -- ft960301_0512_0500S006201M.fits 15 -- ft960301_0512_0500S006401M.fits 16 -- ft960301_0512_0500S006601M.fits 17 -- ft960301_0512_0500S006801M.fits 18 -- ft960301_0512_0500S007001M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S002001M.fits 2 -- ft960301_0512_0500S002401M.fits 3 -- ft960301_0512_0500S002901M.fits 4 -- ft960301_0512_0500S003601M.fits 5 -- ft960301_0512_0500S004001M.fits 6 -- ft960301_0512_0500S004201M.fits 7 -- ft960301_0512_0500S004401M.fits 8 -- ft960301_0512_0500S004601M.fits 9 -- ft960301_0512_0500S004801M.fits 10 -- ft960301_0512_0500S005401M.fits 11 -- ft960301_0512_0500S005601M.fits 12 -- ft960301_0512_0500S005801M.fits 13 -- ft960301_0512_0500S006001M.fits 14 -- ft960301_0512_0500S006201M.fits 15 -- ft960301_0512_0500S006401M.fits 16 -- ft960301_0512_0500S006601M.fits 17 -- ft960301_0512_0500S006801M.fits 18 -- ft960301_0512_0500S007001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s000301l.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S002501L.fits 2 -- ft960301_0512_0500S002701L.fits 3 -- ft960301_0512_0500S003001L.fits 4 -- ft960301_0512_0500S003201L.fits 5 -- ft960301_0512_0500S004301L.fits 6 -- ft960301_0512_0500S004701L.fits 7 -- ft960301_0512_0500S005501L.fits 8 -- ft960301_0512_0500S005701L.fits 9 -- ft960301_0512_0500S006901L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S002501L.fits 2 -- ft960301_0512_0500S002701L.fits 3 -- ft960301_0512_0500S003001L.fits 4 -- ft960301_0512_0500S003201L.fits 5 -- ft960301_0512_0500S004301L.fits 6 -- ft960301_0512_0500S004701L.fits 7 -- ft960301_0512_0500S005501L.fits 8 -- ft960301_0512_0500S005701L.fits 9 -- ft960301_0512_0500S006901L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s000401h.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S000101H.fits 2 -- ft960301_0512_0500S000701H.fits 3 -- ft960301_0512_0500S001201H.fits 4 -- ft960301_0512_0500S001401H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S000101H.fits 2 -- ft960301_0512_0500S000701H.fits 3 -- ft960301_0512_0500S001201H.fits 4 -- ft960301_0512_0500S001401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s000501m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S000201M.fits 2 -- ft960301_0512_0500S000801M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S000201M.fits 2 -- ft960301_0512_0500S000801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s000601l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S000401L.fits 2 -- ft960301_0512_0500S000601L.fits 3 -- ft960301_0512_0500S000901L.fits 4 -- ft960301_0512_0500S001101L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S000401L.fits 2 -- ft960301_0512_0500S000601L.fits 3 -- ft960301_0512_0500S000901L.fits 4 -- ft960301_0512_0500S001101L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000256 events
ft960301_0512_0500S001801H.fits-> Ignoring the following files containing 000000152 events
ft960301_0512_0500S000501L.fits ft960301_0512_0500S001001L.fits-> Ignoring the following files containing 000000144 events
ft960301_0512_0500S005001H.fits-> Ignoring the following files containing 000000045 events
ft960301_0512_0500S005201H.fits-> Ignoring the following files containing 000000032 events
ft960301_0512_0500S002601L.fits-> Ignoring the following files containing 000000015 events
ft960301_0512_0500S005901M.fits-> Ignoring the following files containing 000000004 events
ft960301_0512_0500S001501H.fits-> Ignoring the following files containing 000000002 events
ft960301_0512_0500S001601H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 14 photon cnt = 119647 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 82 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 7 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 4 photon cnt = 18053 SIS1SORTSPLIT:LO:s100501h.prelist merge count = 1 photon cnt = 256 SIS1SORTSPLIT:LO:s100601l.prelist merge count = 9 photon cnt = 24573 SIS1SORTSPLIT:LO:s100701l.prelist merge count = 4 photon cnt = 4017 SIS1SORTSPLIT:LO:s100801l.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:s100901l.prelist merge count = 2 photon cnt = 152 SIS1SORTSPLIT:LO:s101001m.prelist merge count = 17 photon cnt = 110809 SIS1SORTSPLIT:LO:s101101m.prelist merge count = 2 photon cnt = 8123 SIS1SORTSPLIT:LO:Total filenames split = 56 SIS1SORTSPLIT:LO:Total split file cnt = 11 SIS1SORTSPLIT:LO:End program-> Creating ad24043000s100101h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S101601H.fits 2 -- ft960301_0512_0500S102001H.fits 3 -- ft960301_0512_0500S102201H.fits 4 -- ft960301_0512_0500S102701H.fits 5 -- ft960301_0512_0500S103201H.fits 6 -- ft960301_0512_0500S103401H.fits 7 -- ft960301_0512_0500S103801H.fits 8 -- ft960301_0512_0500S104001H.fits 9 -- ft960301_0512_0500S104801H.fits 10 -- ft960301_0512_0500S105001H.fits 11 -- ft960301_0512_0500S105601H.fits 12 -- ft960301_0512_0500S105801H.fits 13 -- ft960301_0512_0500S106001H.fits 14 -- ft960301_0512_0500S106201H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S101601H.fits 2 -- ft960301_0512_0500S102001H.fits 3 -- ft960301_0512_0500S102201H.fits 4 -- ft960301_0512_0500S102701H.fits 5 -- ft960301_0512_0500S103201H.fits 6 -- ft960301_0512_0500S103401H.fits 7 -- ft960301_0512_0500S103801H.fits 8 -- ft960301_0512_0500S104001H.fits 9 -- ft960301_0512_0500S104801H.fits 10 -- ft960301_0512_0500S105001H.fits 11 -- ft960301_0512_0500S105601H.fits 12 -- ft960301_0512_0500S105801H.fits 13 -- ft960301_0512_0500S106001H.fits 14 -- ft960301_0512_0500S106201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s100201m.unf
---- cmerge: version 1.5 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S101901M.fits 2 -- ft960301_0512_0500S102301M.fits 3 -- ft960301_0512_0500S102801M.fits 4 -- ft960301_0512_0500S103501M.fits 5 -- ft960301_0512_0500S103901M.fits 6 -- ft960301_0512_0500S104101M.fits 7 -- ft960301_0512_0500S104301M.fits 8 -- ft960301_0512_0500S104501M.fits 9 -- ft960301_0512_0500S104701M.fits 10 -- ft960301_0512_0500S105101M.fits 11 -- ft960301_0512_0500S105301M.fits 12 -- ft960301_0512_0500S105501M.fits 13 -- ft960301_0512_0500S105701M.fits 14 -- ft960301_0512_0500S105901M.fits 15 -- ft960301_0512_0500S106101M.fits 16 -- ft960301_0512_0500S106301M.fits 17 -- ft960301_0512_0500S106501M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S101901M.fits 2 -- ft960301_0512_0500S102301M.fits 3 -- ft960301_0512_0500S102801M.fits 4 -- ft960301_0512_0500S103501M.fits 5 -- ft960301_0512_0500S103901M.fits 6 -- ft960301_0512_0500S104101M.fits 7 -- ft960301_0512_0500S104301M.fits 8 -- ft960301_0512_0500S104501M.fits 9 -- ft960301_0512_0500S104701M.fits 10 -- ft960301_0512_0500S105101M.fits 11 -- ft960301_0512_0500S105301M.fits 12 -- ft960301_0512_0500S105501M.fits 13 -- ft960301_0512_0500S105701M.fits 14 -- ft960301_0512_0500S105901M.fits 15 -- ft960301_0512_0500S106101M.fits 16 -- ft960301_0512_0500S106301M.fits 17 -- ft960301_0512_0500S106501M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s100301l.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S102401L.fits 2 -- ft960301_0512_0500S102601L.fits 3 -- ft960301_0512_0500S102901L.fits 4 -- ft960301_0512_0500S103101L.fits 5 -- ft960301_0512_0500S104201L.fits 6 -- ft960301_0512_0500S104601L.fits 7 -- ft960301_0512_0500S105201L.fits 8 -- ft960301_0512_0500S105401L.fits 9 -- ft960301_0512_0500S106401L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S102401L.fits 2 -- ft960301_0512_0500S102601L.fits 3 -- ft960301_0512_0500S102901L.fits 4 -- ft960301_0512_0500S103101L.fits 5 -- ft960301_0512_0500S104201L.fits 6 -- ft960301_0512_0500S104601L.fits 7 -- ft960301_0512_0500S105201L.fits 8 -- ft960301_0512_0500S105401L.fits 9 -- ft960301_0512_0500S106401L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s100401h.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S100101H.fits 2 -- ft960301_0512_0500S100701H.fits 3 -- ft960301_0512_0500S101201H.fits 4 -- ft960301_0512_0500S101401H.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S100101H.fits 2 -- ft960301_0512_0500S100701H.fits 3 -- ft960301_0512_0500S101201H.fits 4 -- ft960301_0512_0500S101401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s100501m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S100201M.fits 2 -- ft960301_0512_0500S100801M.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S100201M.fits 2 -- ft960301_0512_0500S100801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad24043000s100601l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960301_0512_0500S100401L.fits 2 -- ft960301_0512_0500S100601L.fits 3 -- ft960301_0512_0500S100901L.fits 4 -- ft960301_0512_0500S101101L.fits Merging binary extension #: 2 1 -- ft960301_0512_0500S100401L.fits 2 -- ft960301_0512_0500S100601L.fits 3 -- ft960301_0512_0500S100901L.fits 4 -- ft960301_0512_0500S101101L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000256 events
ft960301_0512_0500S101701H.fits-> Ignoring the following files containing 000000152 events
ft960301_0512_0500S100501L.fits ft960301_0512_0500S101001L.fits-> Ignoring the following files containing 000000082 events
ft960301_0512_0500S104901H.fits-> Ignoring the following files containing 000000032 events
ft960301_0512_0500S102501L.fits-> Ignoring the following files containing 000000007 events
ft960301_0512_0500S101501H.fits-> Tar-ing together the leftover raw files
a ft960301_0512_0500G200270M.fits 40K a ft960301_0512_0500G200670L.fits 40K a ft960301_0512_0500G200870H.fits 40K a ft960301_0512_0500G200970H.fits 40K a ft960301_0512_0500G201070H.fits 40K a ft960301_0512_0500G201270M.fits 40K a ft960301_0512_0500G201470L.fits 40K a ft960301_0512_0500G202170H.fits 40K a ft960301_0512_0500G202270H.fits 40K a ft960301_0512_0500G203470H.fits 40K a ft960301_0512_0500G203570H.fits 40K a ft960301_0512_0500G204070M.fits 40K a ft960301_0512_0500G204370L.fits 40K a ft960301_0512_0500G205170H.fits 40K a ft960301_0512_0500G205370M.fits 40K a ft960301_0512_0500G205670L.fits 40K a ft960301_0512_0500G206270H.fits 40K a ft960301_0512_0500G206370H.fits 40K a ft960301_0512_0500G206470H.fits 40K a ft960301_0512_0500G206670H.fits 40K a ft960301_0512_0500G207170H.fits 40K a ft960301_0512_0500G207270H.fits 40K a ft960301_0512_0500G207370H.fits 40K a ft960301_0512_0500G207470H.fits 40K a ft960301_0512_0500G207870M.fits 40K a ft960301_0512_0500G208070M.fits 40K a ft960301_0512_0500G208670H.fits 40K a ft960301_0512_0500G208870H.fits 40K a ft960301_0512_0500G209470H.fits 40K a ft960301_0512_0500G209570H.fits 40K a ft960301_0512_0500G209970H.fits 40K a ft960301_0512_0500G210070H.fits 40K a ft960301_0512_0500G210170H.fits 40K a ft960301_0512_0500G210370H.fits 40K a ft960301_0512_0500G210570M.fits 40K a ft960301_0512_0500G210770M.fits 40K a ft960301_0512_0500G210970L.fits 40K a ft960301_0512_0500G211170M.fits 40K a ft960301_0512_0500G211470M.fits 40K a ft960301_0512_0500G211670M.fits 40K a ft960301_0512_0500G211970M.fits 40K a ft960301_0512_0500G212170M.fits 40K a ft960301_0512_0500G212370L.fits 40K a ft960301_0512_0500G212570M.fits 40K a ft960301_0512_0500G212670M.fits 40K a ft960301_0512_0500G212770M.fits 40K a ft960301_0512_0500G212970M.fits 40K a ft960301_0512_0500G213170M.fits 45K a ft960301_0512_0500G213370H.fits 40K a ft960301_0512_0500G213470H.fits 40K a ft960301_0512_0500G213570H.fits 40K a ft960301_0512_0500G213770H.fits 40K a ft960301_0512_0500G213970M.fits 40K a ft960301_0512_0500G214170L.fits 40K a ft960301_0512_0500G214370M.fits 40K a ft960301_0512_0500G214470M.fits 40K a ft960301_0512_0500G214570M.fits 40K a ft960301_0512_0500G214870M.fits 40K a ft960301_0512_0500G214970M.fits 40K a ft960301_0512_0500G215070M.fits 40K a ft960301_0512_0500G215370H.fits 40K a ft960301_0512_0500G215470H.fits 40K a ft960301_0512_0500G215670H.fits 40K a ft960301_0512_0500G215870H.fits 40K a ft960301_0512_0500G216070M.fits 40K a ft960301_0512_0500G216270H.fits 40K a ft960301_0512_0500G216470H.fits 40K a ft960301_0512_0500G216670M.fits 40K a ft960301_0512_0500G216970H.fits 40K a ft960301_0512_0500G217070H.fits 40K a ft960301_0512_0500G217270M.fits 40K a ft960301_0512_0500G217470M.fits 40K a ft960301_0512_0500G217670M.fits 40K a ft960301_0512_0500G217870H.fits 40K a ft960301_0512_0500G217970H.fits 40K a ft960301_0512_0500G218070H.fits 40K a ft960301_0512_0500G218270M.fits 40K a ft960301_0512_0500G218670L.fits 40K a ft960301_0512_0500G218870M.fits 40K a ft960301_0512_0500G218970M.fits 40K a ft960301_0512_0500G219070M.fits 40K a ft960301_0512_0500G300270H.fits 40K a ft960301_0512_0500G300470M.fits 40K a ft960301_0512_0500G300770L.fits 40K a ft960301_0512_0500G300870L.fits 40K a ft960301_0512_0500G301070H.fits 40K a ft960301_0512_0500G301170H.fits 40K a ft960301_0512_0500G301270H.fits 40K a ft960301_0512_0500G301470M.fits 40K a ft960301_0512_0500G301670L.fits 40K a ft960301_0512_0500G302370H.fits 40K a ft960301_0512_0500G302470H.fits 40K a ft960301_0512_0500G303770H.fits 40K a ft960301_0512_0500G303870H.fits 40K a ft960301_0512_0500G304270M.fits 40K a ft960301_0512_0500G304570L.fits 40K a ft960301_0512_0500G305170H.fits 40K a ft960301_0512_0500G305270H.fits 40K a ft960301_0512_0500G305370H.fits 40K a ft960301_0512_0500G305570M.fits 40K a ft960301_0512_0500G305870L.fits 40K a ft960301_0512_0500G306670H.fits 40K a ft960301_0512_0500G306870H.fits 40K a ft960301_0512_0500G306970H.fits 40K a ft960301_0512_0500G307470H.fits 40K a ft960301_0512_0500G307570H.fits 40K a ft960301_0512_0500G307970M.fits 40K a ft960301_0512_0500G308170M.fits 40K a ft960301_0512_0500G308870H.fits 40K a ft960301_0512_0500G308970H.fits 40K a ft960301_0512_0500G309170H.fits 40K a ft960301_0512_0500G309270H.fits 40K a ft960301_0512_0500G309770H.fits 40K a ft960301_0512_0500G310170H.fits 40K a ft960301_0512_0500G310370H.fits 40K a ft960301_0512_0500G310570H.fits 40K a ft960301_0512_0500G310770H.fits 40K a ft960301_0512_0500G310970H.fits 40K a ft960301_0512_0500G311170H.fits 40K a ft960301_0512_0500G311370M.fits 40K a ft960301_0512_0500G311570M.fits 40K a ft960301_0512_0500G311770M.fits 40K a ft960301_0512_0500G311970L.fits 40K a ft960301_0512_0500G312170M.fits 40K a ft960301_0512_0500G312770M.fits 40K a ft960301_0512_0500G312970M.fits 40K a ft960301_0512_0500G313170M.fits 40K a ft960301_0512_0500G313270M.fits 40K a ft960301_0512_0500G313470M.fits 40K a ft960301_0512_0500G313670L.fits 40K a ft960301_0512_0500G313870L.fits 40K a ft960301_0512_0500G314070M.fits 40K a ft960301_0512_0500G314170M.fits 40K a ft960301_0512_0500G314270M.fits 40K a ft960301_0512_0500G314470H.fits 40K a ft960301_0512_0500G314570H.fits 40K a ft960301_0512_0500G314670H.fits 40K a ft960301_0512_0500G314870H.fits 40K a ft960301_0512_0500G315070H.fits 40K a ft960301_0512_0500G315270M.fits 40K a ft960301_0512_0500G315470L.fits 40K a ft960301_0512_0500G315670M.fits 40K a ft960301_0512_0500G315770M.fits 40K a ft960301_0512_0500G315870M.fits 40K a ft960301_0512_0500G316070M.fits 40K a ft960301_0512_0500G316370M.fits 40K a ft960301_0512_0500G316470M.fits 40K a ft960301_0512_0500G316570M.fits 40K a ft960301_0512_0500G316770H.fits 40K a ft960301_0512_0500G316870H.fits 40K a ft960301_0512_0500G316970H.fits 40K a ft960301_0512_0500G317170H.fits 40K a ft960301_0512_0500G317370M.fits 40K a ft960301_0512_0500G317570H.fits 40K a ft960301_0512_0500G317970H.fits 40K a ft960301_0512_0500G318170M.fits 40K a ft960301_0512_0500G318470H.fits 40K a ft960301_0512_0500G318570H.fits 40K a ft960301_0512_0500G318970M.fits 40K a ft960301_0512_0500G319170M.fits 40K a ft960301_0512_0500G319370M.fits 40K a ft960301_0512_0500G319570H.fits 40K a ft960301_0512_0500G319670H.fits 40K a ft960301_0512_0500G319770H.fits 40K a ft960301_0512_0500G319970M.fits 40K a ft960301_0512_0500G320370L.fits 40K a ft960301_0512_0500G320570M.fits 40K a ft960301_0512_0500G320670M.fits 40K a ft960301_0512_0500G320770M.fits 40K a ft960301_0512_0500S000501L.fits 40K a ft960301_0512_0500S001001L.fits 43K a ft960301_0512_0500S001501H.fits 40K a ft960301_0512_0500S001601H.fits 40K a ft960301_0512_0500S001801H.fits 48K a ft960301_0512_0500S002601L.fits 40K a ft960301_0512_0500S005001H.fits 43K a ft960301_0512_0500S005201H.fits 40K a ft960301_0512_0500S005901M.fits 40K a ft960301_0512_0500S100501L.fits 40K a ft960301_0512_0500S101001L.fits 43K a ft960301_0512_0500S101501H.fits 40K a ft960301_0512_0500S101701H.fits 48K a ft960301_0512_0500S102501L.fits 40K a ft960301_0512_0500S104901H.fits 43K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft960301_0512.0500 'ft960301_0512.0500' is successfully opened Data Start Time is 99810767.00 (960301 051247) Time Margin 2.0 sec included Sync error detected in 170 th SF Sync error detected in 174 th SF Sync error detected in 178 th SF Sync error detected in 5154 th SF Sync error detected in 7107 th SF Sync error detected in 9383 th SF Sync error detected in 9786 th SF Sync error detected in 9892 th SF Sync error detected in 9902 th SF Sync error detected in 9914 th SF Sync error detected in 9919 th SF Sync error detected in 10008 th SF Sync error detected in 10009 th SF Sync error detected in 10011 th SF Sync error detected in 10012 th SF Sync error detected in 10024 th SF Sync error detected in 10041 th SF Sync error detected in 10067 th SF Sync error detected in 10068 th SF Sync error detected in 10090 th SF Sync error detected in 10094 th SF Sync error detected in 10152 th SF Sync error detected in 10183 th SF Sync error detected in 10194 th SF Sync error detected in 10210 th SF Sync error detected in 10281 th SF Sync error detected in 10288 th SF Sync error detected in 10294 th SF Sync error detected in 10370 th SF Sync error detected in 10395 th SF Sync error detected in 10412 th SF Sync error detected in 10414 th SF Sync error detected in 10437 th SF Sync error detected in 10440 th SF Sync error detected in 10450 th SF Sync error detected in 10482 th SF Sync error detected in 10497 th SF Sync error detected in 10498 th SF Sync error detected in 10538 th SF Sync error detected in 10590 th SF Sync error detected in 10598 th SF Sync error detected in 10615 th SF Sync error detected in 10623 th SF Sync error detected in 10632 th SF Sync error detected in 10665 th SF Sync error detected in 10668 th SF Sync error detected in 10679 th SF Sync error detected in 10687 th SF Sync error detected in 10688 th SF Sync error detected in 10689 th SF Sync error detected in 10690 th SF Sync error detected in 10691 th SF Sync error detected in 10693 th SF Sync error detected in 10713 th SF Sync error detected in 10750 th SF Sync error detected in 10766 th SF Sync error detected in 10767 th SF Sync error detected in 10778 th SF Sync error detected in 10786 th SF Sync error detected in 10848 th SF Sync error detected in 10875 th SF Sync error detected in 10876 th SF Sync error detected in 10886 th SF Sync error detected in 10889 th SF Sync error detected in 10934 th SF Sync error detected in 10964 th SF Sync error detected in 11009 th SF Sync error detected in 11012 th SF Sync error detected in 11026 th SF Sync error detected in 11038 th SF Sync error detected in 11058 th SF Sync error detected in 11061 th SF Sync error detected in 11075 th SF Sync error detected in 11235 th SF Sync error detected in 11485 th SF Sync error detected in 11540 th SF Sync error detected in 11611 th SF Sync error detected in 11661 th SF Sync error detected in 11759 th SF Sync error detected in 11772 th SF Sync error detected in 11784 th SF Sync error detected in 11840 th SF Sync error detected in 11841 th SF Sync error detected in 11857 th SF Sync error detected in 11913 th SF Sync error detected in 11918 th SF Sync error detected in 11926 th SF Sync error detected in 11973 th SF Sync error detected in 11979 th SF Sync error detected in 11994 th SF Sync error detected in 12055 th SF Sync error detected in 12078 th SF Sync error detected in 12129 th SF Sync error detected in 13783 th SF Sync error detected in 13846 th SF Sync error detected in 13848 th SF Sync error detected in 13849 th SF Sync error detected in 15311 th SF Sync error detected in 15330 th SF Sync error detected in 15353 th SF Sync error detected in 15416 th SF Sync error detected in 15479 th SF Sync error detected in 15481 th SF Sync error detected in 15483 th SF Sync error detected in 15484 th SF Sync error detected in 15485 th SF Sync error detected in 15486 th SF Sync error detected in 15490 th SF Sync error detected in 15542 th SF Sync error detected in 15601 th SF Sync error detected in 15602 th SF Sync error detected in 15603 th SF Sync error detected in 15604 th SF Sync error detected in 15605 th SF Sync error detected in 15606 th SF Sync error detected in 15607 th SF Sync error detected in 15608 th SF Sync error detected in 15609 th SF Sync error detected in 15731 th SF Sync error detected in 15809 th SF Sync error detected in 15840 th SF 'ft960301_0512.0500' EOF detected, sf=17371 Data End Time is 99896462.74 (960302 050102) Gain History is written in ft960301_0512_0500.ghf-> Checking if column CAL_START in ft960301_0512_0500.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft960301_0512_0500.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g200470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000g300470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000201m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000212m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000301l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000302l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000312l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s000401h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s000402h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s000412h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s000501m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s000601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100201m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100212m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100301l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100302l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100312l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 99847335.386440 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad24043000s100401h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100402h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100412h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100501m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100502m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100512m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad24043000s100601l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 96/ 3/ 1 5:12 mjd=50143.216667 Orbit file name is ./frf.orbit.213 Epoch of Orbital Elements: 1996/2/26 18:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa960301_0512.0500 S0-HK file: ft960301_0512_0500S0HK.fits S1-HK file: ft960301_0512_0500S1HK.fits G2-HK file: ft960301_0512_0500G2HK.fits G3-HK file: ft960301_0512_0500G3HK.fits output FITS File: ft960301_0512_0500.mkf Total 2679 Data bins were processed.-> Checking if column TIME in ft960301_0512_0500.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 13298.473 The mean of the selected column is 22.928402 The standard deviation of the selected column is 40.731284 The minimum of selected column is 2.8289564 The maximum of selected column is 783.56488 The number of points used in calculation is 580-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<145.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.25E+05 13141 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
11553 8459 0 3094 0 0
Writing events file
8459 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11553 8459 0 3094 0 0
in 18893.13 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 8459
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 6669
Flickering pixels iter, pixels & cnts : 1 5 64
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 8459
Number of image cts rejected (N, %) : 6733 79.5956955
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 8459 0 0
Image cts rejected: 0 6733 0 0
Image cts rej (%) : 0.00 79.60 0.00 0.00
filtering data...
Total counts : 0 8459 0 0
Total cts rejected: 0 6733 0 0
Total cts rej (%) : 0.00 79.60 0.00 0.00
Number of clean counts accepted : 1726
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad24043000s000102h.evt use_events=no
Wrote cleaned events file to ad24043000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad24043000s000112h.unf into ad24043000s000112h.evtThe sum of the selected column is 13298.473 The mean of the selected column is 22.928402 The standard deviation of the selected column is 40.731284 The minimum of selected column is 2.8289564 The maximum of selected column is 783.56488 The number of points used in calculation is 580-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<145.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.25E+05 13589 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
11710 8563 0 3147 0 0
Writing events file
8563 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11710 8563 0 3147 0 0
in 18893.13 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 8563
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 6669
Flickering pixels iter, pixels & cnts : 1 5 64
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 8563
Number of image cts rejected (N, %) : 6733 78.6289825
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 8563 0 0
Image cts rejected: 0 6733 0 0
Image cts rej (%) : 0.00 78.63 0.00 0.00
filtering data...
Total counts : 0 8563 0 0
Total cts rejected: 0 6733 0 0
Total cts rej (%) : 0.00 78.63 0.00 0.00
Number of clean counts accepted : 1830
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad24043000s000112h.evt use_events=no
Wrote cleaned events file to ad24043000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s000201m.unf because of modeThe sum of the selected column is 9225.8563 The mean of the selected column is 22.723784 The standard deviation of the selected column is 31.331881 The minimum of selected column is 4.8500175 The maximum of selected column is 439.93906 The number of points used in calculation is 406-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<116.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.23E+05 11050 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9900 6113 0 3787 0 0
Writing events file
6113 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9900 6113 0 3787 0 0
in 12997.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 6113
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 4879
Flickering pixels iter, pixels & cnts : 1 4 32
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 6113
Number of image cts rejected (N, %) : 4911 80.3369904
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 6113 0 0
Image cts rejected: 0 4911 0 0
Image cts rej (%) : 0.00 80.34 0.00 0.00
filtering data...
Total counts : 0 6113 0 0
Total cts rejected: 0 4911 0 0
Total cts rej (%) : 0.00 80.34 0.00 0.00
Number of clean counts accepted : 1202
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad24043000s000202m.evt use_events=no
Wrote cleaned events file to ad24043000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad24043000s000212m.unf into ad24043000s000212m.evtThe sum of the selected column is 9225.8563 The mean of the selected column is 22.723784 The standard deviation of the selected column is 31.331881 The minimum of selected column is 4.8500175 The maximum of selected column is 439.93906 The number of points used in calculation is 406-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<116.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.23E+05 11351 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10015 6178 0 3837 0 0
Writing events file
6178 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10015 6178 0 3837 0 0
in 12997.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 6178
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 4851
Flickering pixels iter, pixels & cnts : 1 5 60
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 6178
Number of image cts rejected (N, %) : 4911 79.4917450
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 6178 0 0
Image cts rejected: 0 4911 0 0
Image cts rej (%) : 0.00 79.49 0.00 0.00
filtering data...
Total counts : 0 6178 0 0
Total cts rejected: 0 4911 0 0
Total cts rej (%) : 0.00 79.49 0.00 0.00
Number of clean counts accepted : 1267
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad24043000s000212m.evt use_events=no
Wrote cleaned events file to ad24043000s000212m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s000301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT LOW 01/03/96 10:40:54 0.12E+05 4120 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad24043000s000302l.evt use_events=no
Wrote cleaned events file to ad24043000s000302l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad24043000s000302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 LOW 01/03/96 10:40:54 0.12E+05 4217 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000312l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad24043000s000312l.evt use_events=no
Wrote cleaned events file to ad24043000s000312l.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad24043000s000312l.evt since it contains 0 eventsThe sum of the selected column is 1938.8679 The mean of the selected column is 17.952481 The standard deviation of the selected column is 11.018391 The minimum of selected column is 4.7678814 The maximum of selected column is 75.062744 The number of points used in calculation is 108-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<51 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.51E+04 2106 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1866 1198 0 668 0 0
Writing events file
1198 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1866 1198 0 668 0 0
in 3377.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1198
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 932
Flickering pixels iter, pixels & cnts : 1 2 9
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 4
Number of (internal) image counts : 1198
Number of image cts rejected (N, %) : 941 78.5475769
By chip : 0 1 2 3
Pixels rejected : 0 4 0 0
Image counts : 0 1198 0 0
Image cts rejected: 0 941 0 0
Image cts rej (%) : 0.00 78.55 0.00 0.00
filtering data...
Total counts : 0 1198 0 0
Total cts rejected: 0 941 0 0
Total cts rej (%) : 0.00 78.55 0.00 0.00
Number of clean counts accepted : 257
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 4
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000402h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad24043000s000402h.evt use_events=no
Wrote cleaned events file to ad24043000s000402h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad24043000s000412h.unf into ad24043000s000412h.evtThe sum of the selected column is 1938.8679 The mean of the selected column is 17.952481 The standard deviation of the selected column is 11.018391 The minimum of selected column is 4.7678814 The maximum of selected column is 75.062744 The number of points used in calculation is 108-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<51 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.51E+04 2181 0100
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1889 1216 0 673 0 0
Writing events file
1216 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1889 1216 0 673 0 0
in 3377.72 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1216
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 932
Flickering pixels iter, pixels & cnts : 1 2 9
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 4
Number of (internal) image counts : 1216
Number of image cts rejected (N, %) : 941 77.3848648
By chip : 0 1 2 3
Pixels rejected : 0 4 0 0
Image counts : 0 1216 0 0
Image cts rejected: 0 941 0 0
Image cts rej (%) : 0.00 77.38 0.00 0.00
filtering data...
Total counts : 0 1216 0 0
Total cts rejected: 0 941 0 0
Total cts rej (%) : 0.00 77.38 0.00 0.00
Number of clean counts accepted : 275
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 4
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s000412h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad24043000s000412h.evt use_events=no
Wrote cleaned events file to ad24043000s000412h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s000501m.unf because of modeThe sum of the selected column is 20968.469 The mean of the selected column is 36.028297 The standard deviation of the selected column is 65.956205 The minimum of selected column is 6.3815994 The maximum of selected column is 1458.7233 The number of points used in calculation is 582-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<233.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.25E+05 64908 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
63453 48368 0 15085 0 0
Writing events file
48368 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
63453 48368 0 15085 0 0
in 18907.16 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 48368
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 18 46349
Flickering pixels iter, pixels & cnts : 1 8 404
Number of pixels rejected : 26
Number of (internal) image counts : 48368
Number of image cts rejected (N, %) : 46753 96.6610184
By chip : 0 1 2 3
Pixels rejected : 0 0 0 26
Image counts : 0 0 0 48368
Image cts rejected: 0 0 0 46753
Image cts rej (%) : 0.00 0.00 0.00 96.66
filtering data...
Total counts : 0 0 0 48368
Total cts rejected: 0 0 0 46753
Total cts rej (%) : 0.00 0.00 0.00 96.66
Number of clean counts accepted : 1615
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad24043000s100102h.evt use_events=no
Wrote cleaned events file to ad24043000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad24043000s100112h.unf into ad24043000s100112h.evtThe sum of the selected column is 20968.469 The mean of the selected column is 36.028297 The standard deviation of the selected column is 65.956205 The minimum of selected column is 6.3815994 The maximum of selected column is 1458.7233 The number of points used in calculation is 582-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<233.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.25E+05 65256 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
63588 48450 0 15138 0 0
Writing events file
48450 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
63588 48450 0 15138 0 0
in 18907.16 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 48450
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 18 46357
Flickering pixels iter, pixels & cnts : 1 8 404
Number of pixels rejected : 26
Number of (internal) image counts : 48450
Number of image cts rejected (N, %) : 46761 96.5139313
By chip : 0 1 2 3
Pixels rejected : 0 0 0 26
Image counts : 0 0 0 48450
Image cts rejected: 0 0 0 46761
Image cts rej (%) : 0.00 0.00 0.00 96.51
filtering data...
Total counts : 0 0 0 48450
Total cts rejected: 0 0 0 46761
Total cts rej (%) : 0.00 0.00 0.00 96.51
Number of clean counts accepted : 1689
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad24043000s100112h.evt use_events=no
Wrote cleaned events file to ad24043000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s100201m.unf because of modeThe sum of the selected column is 14291.761 The mean of the selected column is 35.288298 The standard deviation of the selected column is 46.973588 The minimum of selected column is 5.7500176 The maximum of selected column is 662.84583 The number of points used in calculation is 405-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<176.2 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.23E+05 60446 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
58691 35628 0 23063 0 0
Writing events file
35628 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
58691 35628 0 23063 0 0
in 12983.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 35628
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 19 34323
Flickering pixels iter, pixels & cnts : 1 9 271
Number of pixels rejected : 28
Number of (internal) image counts : 35628
Number of image cts rejected (N, %) : 34594 97.0977859
By chip : 0 1 2 3
Pixels rejected : 0 0 0 28
Image counts : 0 0 0 35628
Image cts rejected: 0 0 0 34594
Image cts rej (%) : 0.00 0.00 0.00 97.10
filtering data...
Total counts : 0 0 0 35628
Total cts rejected: 0 0 0 34594
Total cts rej (%) : 0.00 0.00 0.00 97.10
Number of clean counts accepted : 1034
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 28
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad24043000s100202m.evt use_events=no
Wrote cleaned events file to ad24043000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad24043000s100212m.unf into ad24043000s100212m.evtThe sum of the selected column is 14291.761 The mean of the selected column is 35.288298 The standard deviation of the selected column is 46.973588 The minimum of selected column is 5.7500176 The maximum of selected column is 662.84583 The number of points used in calculation is 405-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<176.2 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.23E+05 60695 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
58806 35671 0 23135 0 0
Writing events file
35671 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
58806 35671 0 23135 0 0
in 12983.97 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 35671
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 19 34325
Flickering pixels iter, pixels & cnts : 1 9 271
Number of pixels rejected : 28
Number of (internal) image counts : 35671
Number of image cts rejected (N, %) : 34596 96.9863510
By chip : 0 1 2 3
Pixels rejected : 0 0 0 28
Image counts : 0 0 0 35671
Image cts rejected: 0 0 0 34596
Image cts rej (%) : 0.00 0.00 0.00 96.99
filtering data...
Total counts : 0 0 0 35671
Total cts rejected: 0 0 0 34596
Total cts rej (%) : 0.00 0.00 0.00 96.99
Number of clean counts accepted : 1075
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 28
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad24043000s100212m.evt use_events=no
Wrote cleaned events file to ad24043000s100212m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s100301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT LOW 01/03/96 10:40:54 0.12E+05 12398 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad24043000s100302l.evt use_events=no
Wrote cleaned events file to ad24043000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad24043000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 LOW 01/03/96 10:40:54 0.12E+05 12453 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad24043000s100312l.evt use_events=no
Wrote cleaned events file to ad24043000s100312l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad24043000s100312l.evt since it contains 0 eventsThe sum of the selected column is 3257.6619 The mean of the selected column is 29.886806 The standard deviation of the selected column is 12.275062 The minimum of selected column is 4.5000143 The maximum of selected column is 77.687752 The number of points used in calculation is 109-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<66.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.52E+04 9767 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9536 6402 0 3134 0 0
Writing events file
6402 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9536 6402 0 3134 0 0
in 3511.75 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 6402
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 6083
Flickering pixels iter, pixels & cnts : 1 4 38
Number of pixels rejected : 15
Number of (internal) image counts : 6402
Number of image cts rejected (N, %) : 6121 95.6107483
By chip : 0 1 2 3
Pixels rejected : 0 0 0 15
Image counts : 0 0 0 6402
Image cts rejected: 0 0 0 6121
Image cts rej (%) : 0.00 0.00 0.00 95.61
filtering data...
Total counts : 0 0 0 6402
Total cts rejected: 0 0 0 6121
Total cts rej (%) : 0.00 0.00 0.00 95.61
Number of clean counts accepted : 281
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 15
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad24043000s100402h.evt use_events=no
Wrote cleaned events file to ad24043000s100402h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad24043000s100412h.unf into ad24043000s100412h.evtThe sum of the selected column is 3257.6619 The mean of the selected column is 29.886806 The standard deviation of the selected column is 12.275062 The minimum of selected column is 4.5000143 The maximum of selected column is 77.687752 The number of points used in calculation is 109-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<66.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.52E+04 9835 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9564 6420 0 3144 0 0
Writing events file
6420 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9564 6420 0 3144 0 0
in 3511.75 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 6420
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 6085
Flickering pixels iter, pixels & cnts : 1 4 38
Number of pixels rejected : 15
Number of (internal) image counts : 6420
Number of image cts rejected (N, %) : 6123 95.3738327
By chip : 0 1 2 3
Pixels rejected : 0 0 0 15
Image counts : 0 0 0 6420
Image cts rejected: 0 0 0 6123
Image cts rej (%) : 0.00 0.00 0.00 95.37
filtering data...
Total counts : 0 0 0 6420
Total cts rejected: 0 0 0 6123
Total cts rej (%) : 0.00 0.00 0.00 95.37
Number of clean counts accepted : 297
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 15
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100412h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad24043000s100412h.evt use_events=no
Wrote cleaned events file to ad24043000s100412h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s100501m.unf because of modeThe sum of the selected column is 1831.2251 The mean of the selected column is 48.190133 The standard deviation of the selected column is 13.528826 The minimum of selected column is 27.875088 The maximum of selected column is 86.187775 The number of points used in calculation is 38-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>7.6 && S1_PIXL3<88.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.21E+04 3950 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3835 2615 0 1220 0 0
Writing events file
2615 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3835 2615 0 1220 0 0
in 1444.02 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 2615
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 2464
Flickering pixels iter, pixels & cnts : 1 4 38
Number of pixels rejected : 13
Number of (internal) image counts : 2615
Number of image cts rejected (N, %) : 2502 95.6787796
By chip : 0 1 2 3
Pixels rejected : 0 0 0 13
Image counts : 0 0 0 2615
Image cts rejected: 0 0 0 2502
Image cts rej (%) : 0.00 0.00 0.00 95.68
filtering data...
Total counts : 0 0 0 2615
Total cts rejected: 0 0 0 2502
Total cts rej (%) : 0.00 0.00 0.00 95.68
Number of clean counts accepted : 113
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad24043000s100502m.evt use_events=no
Wrote cleaned events file to ad24043000s100502m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad24043000s100512m.unf into ad24043000s100512m.evtThe sum of the selected column is 1831.2251 The mean of the selected column is 48.190133 The standard deviation of the selected column is 13.528826 The minimum of selected column is 27.875088 The maximum of selected column is 86.187775 The number of points used in calculation is 38-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>7.6 && S1_PIXL3<88.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.21E+04 3979 0001
Processing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3844 2622 0 1222 0 0
Writing events file
2622 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3844 2622 0 1222 0 0
in 1444.02 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/24043000.003/screen_in_event.xsl
reading data file: /data/data17/seq_proc/24043000.003/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 2622
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 2464
Flickering pixels iter, pixels & cnts : 1 4 38
Number of pixels rejected : 13
Number of (internal) image counts : 2622
Number of image cts rejected (N, %) : 2502 95.4233398
By chip : 0 1 2 3
Pixels rejected : 0 0 0 13
Image counts : 0 0 0 2622
Image cts rejected: 0 0 0 2502
Image cts rej (%) : 0.00 0.00 0.00 95.42
filtering data...
Total counts : 0 0 0 2622
Total cts rejected: 0 0 0 2502
Total cts rej (%) : 0.00 0.00 0.00 95.42
Number of clean counts accepted : 120
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000s100512m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad24043000s100512m.evt use_events=no
Wrote cleaned events file to ad24043000s100512m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad24043000s100601l.unf because of mode(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.unf
Total Good Bad: Region Time Phase Cut
26341 8620 15797 1924 0 0
Writing events file
8620 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26341 8620 15797 1924 0 0
in 21532.57 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8620 7725 895
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad24043000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 7725 in ad24043000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.unf
Total Good Bad: Region Time Phase Cut
21476 6040 13493 1943 0 0
Writing events file
6040 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21476 6040 13493 1943 0 0
in 15359.16 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
6040 5384 656
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad24043000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 5384 in ad24043000g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.97E+04 6757 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.unf
Total Good Bad: Region Time Phase Cut
6757 8 4926 1823 0 0
Writing events file
8 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6757 8 4926 1823 0 0
in 17.81 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8 6 2
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad24043000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 6 in ad24043000g200370l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.unf
Total Good Bad: Region Time Phase Cut
1713 385 1121 207 0 0
Writing events file
385 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1713 385 1121 207 0 0
in 1008.10 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
385 349 36
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad24043000g200470h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 349 in ad24043000g200470h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.unf
Total Good Bad: Region Time Phase Cut
26001 10479 13279 2243 0 0
Writing events file
10479 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26001 10479 13279 2243 0 0
in 21524.57 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
10479 9398 1081
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad24043000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 9398 in ad24043000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.unf
Total Good Bad: Region Time Phase Cut
21040 7390 11549 2101 0 0
Writing events file
7390 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21040 7390 11549 2101 0 0
in 15279.16 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
7390 6643 747
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad24043000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 6643 in ad24043000g300270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.96E+04 6175 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.unf
Total Good Bad: Region Time Phase Cut
6175 3 4157 2015 0 0
Writing events file
3 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6175 3 4157 2015 0 0
in 17.81 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3 3 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad24043000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad24043000g300470h.unf into ad24043000g300470h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1623 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.unf
Total Good Bad: Region Time Phase Cut
1623 415 966 242 0 0
Writing events file
415 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1623 415 966 242 0 0
in 1008.10 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
415 373 42
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!screen:ASCA > read events ad24043000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad24043000g300470h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 373 in ad24043000g300470h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad24043000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6619
Mean RA/DEC/ROLL : 85.3736 -2.3109 99.6619
Pnt RA/DEC/ROLL : 85.2615 -2.2061 99.6619
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 108
Total GTI (secs) : 21532.570
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3387.9794922 3387.9794922
20 Percent Complete: Total/live time: 4714.4760742 4714.4760742
30 Percent Complete: Total/live time: 6706.0141602 6706.0141602
40 Percent Complete: Total/live time: 9664.5058594 9664.5058594
50 Percent Complete: Total/live time: 11064.5009766 11064.5009766
60 Percent Complete: Total/live time: 13271.7031250 13271.7031250
70 Percent Complete: Total/live time: 17000.3300781 17000.3300781
80 Percent Complete: Total/live time: 17784.5976562 17784.5976562
90 Percent Complete: Total/live time: 19924.3203125 19924.3203125
100 Percent Complete: Total/live time: 21532.5703125 21532.5703125
Number of attitude steps used: 85
Number of attitude steps avail: 47810
Mean RA/DEC pixel offset: -9.4415 -4.1066
writing expo file: ad24043000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 7616 109 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 7616 109 0 0 0
in 21532.57 seconds
Image has 7616 counts for 0.3537 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 3480 109 0 0 4136
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 3480 109 0 0 4136
in 21532.57 seconds
Image has 3480 counts for 0.1616 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 4164 109 0 0 3452
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 4164 109 0 0 3452
in 21532.57 seconds
Image has 4164 counts for 0.1934 counts/sec
Command not found; type ? for a command listing
!ad24043000g200170h:ASCA >
!ad24043000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g200170h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g200170h:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g200170h:ASCA-GIS2-PH > set image sky
!ad24043000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad24043000g200170h:ASCA-GIS2-PH > extract image
!ad24043000g200170h:ASCA-GIS2-PH > save image outfile=ad24043000g200170h.img
Wrote image to file ad24043000g200170h.img
!ad24043000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad24043000g200170h:ASCA-GIS2-PH > extract image
!ad24043000g200170h:ASCA-GIS2-PH > save image outfile=ad24043000g200170h_lo.img
Wrote image to file ad24043000g200170h_lo.img
!ad24043000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad24043000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g200170h:ASCA-GIS2-PH > extract image
!ad24043000g200170h:ASCA-GIS2-PH > save image outfile=ad24043000g200170h_hi.img
Wrote image to file ad24043000g200170h_hi.img
!ad24043000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad24043000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6598
Mean RA/DEC/ROLL : 85.3675 -2.3044 99.6598
Pnt RA/DEC/ROLL : 85.3609 -2.3425 99.6598
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 45
Total GTI (secs) : 15359.156
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1694.0217285 1694.0217285
20 Percent Complete: Total/live time: 4138.1582031 4138.1582031
30 Percent Complete: Total/live time: 5347.4125977 5347.4125977
40 Percent Complete: Total/live time: 6705.2504883 6705.2504883
50 Percent Complete: Total/live time: 7909.5595703 7909.5595703
60 Percent Complete: Total/live time: 9410.7255859 9410.7255859
70 Percent Complete: Total/live time: 11227.7197266 11227.7197266
80 Percent Complete: Total/live time: 12880.9023438 12880.9023438
90 Percent Complete: Total/live time: 14240.8984375 14240.8984375
100 Percent Complete: Total/live time: 15359.1582031 15359.1582031
Number of attitude steps used: 86
Number of attitude steps avail: 7587
Mean RA/DEC pixel offset: 6.9697 -3.3865
writing expo file: ad24043000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 5313 71 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 5313 71 0 0 0
in 15359.16 seconds
Image has 5313 counts for 0.3459 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 2511 71 0 0 2802
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 2511 71 0 0 2802
in 15359.16 seconds
Image has 2511 counts for 0.1635 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 2818 71 0 0 2495
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 2818 71 0 0 2495
in 15359.16 seconds
Image has 2818 counts for 0.1835 counts/sec
Command not found; type ? for a command listing
!ad24043000g200270m:ASCA >
!ad24043000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g200270m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g200270m:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g200270m:ASCA-GIS2-PH > set image sky
!ad24043000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad24043000g200270m:ASCA-GIS2-PH > extract image
!ad24043000g200270m:ASCA-GIS2-PH > save image outfile=ad24043000g200270m.img
Wrote image to file ad24043000g200270m.img
!ad24043000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad24043000g200270m:ASCA-GIS2-PH > extract image
!ad24043000g200270m:ASCA-GIS2-PH > save image outfile=ad24043000g200270m_lo.img
Wrote image to file ad24043000g200270m_lo.img
!ad24043000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad24043000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g200270m:ASCA-GIS2-PH > extract image
!ad24043000g200270m:ASCA-GIS2-PH > save image outfile=ad24043000g200270m_hi.img
Wrote image to file ad24043000g200270m_hi.img
!ad24043000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad24043000g200370l.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6598
Mean RA/DEC/ROLL : 85.3683 -2.3042 99.6598
Pnt RA/DEC/ROLL : 85.3549 -2.3492 99.6598
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 1
Total GTI (secs) : 17.805
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 14.8052568 14.8052568
20 Percent Complete: Total/live time: 17.8054657 17.8054657
100 Percent Complete: Total/live time: 17.8054657 17.8054657
Number of attitude steps used: 2
Number of attitude steps avail: 23
Mean RA/DEC pixel offset: -4.4003 -1.7406
writing expo file: ad24043000g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g200370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g200370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 6 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 6 0 0 0 0
in 17.81 seconds
Image has 6 counts for 0.3370 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 5 0 0 0 1
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 5 0 0 0 1
in 17.81 seconds
Image has 5 counts for 0.2808 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 0 0 0 5
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 1 0 0 0 5
in 17.81 seconds
Image has 1 counts for 5.6163E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000g200370l:ASCA >
!ad24043000g200370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g200370l:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g200370l:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g200370l:ASCA-GIS2-PH > set image sky
!ad24043000g200370l:ASCA-GIS2-PH > filter region corner_point.reg
!ad24043000g200370l:ASCA-GIS2-PH > extract image
!ad24043000g200370l:ASCA-GIS2-PH > save image outfile=ad24043000g200370l.img
Wrote image to file ad24043000g200370l.img
!ad24043000g200370l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad24043000g200370l:ASCA-GIS2-PH > extract image
!ad24043000g200370l:ASCA-GIS2-PH > save image outfile=ad24043000g200370l_lo.img
Wrote image to file ad24043000g200370l_lo.img
!ad24043000g200370l:ASCA-GIS2-PH > clear pha_cut
!ad24043000g200370l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g200370l:ASCA-GIS2-PH > extract image
!ad24043000g200370l:ASCA-GIS2-PH > save image outfile=ad24043000g200370l_hi.img
Wrote image to file ad24043000g200370l_hi.img
!ad24043000g200370l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad24043000g200470h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g200470h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6633
Mean RA/DEC/ROLL : 85.3668 -2.3031 99.6633
Pnt RA/DEC/ROLL : 85.3621 -2.3477 99.6633
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 3
Total GTI (secs) : 1008.096
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 144.4995728 144.4995728
20 Percent Complete: Total/live time: 1008.0959473 1008.0959473
100 Percent Complete: Total/live time: 1008.0959473 1008.0959473
Number of attitude steps used: 3
Number of attitude steps avail: 2235
Mean RA/DEC pixel offset: -6.5753 -1.9525
writing expo file: ad24043000g200470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g200470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g200470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 344 5 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 344 5 0 0 0
in 1008.10 seconds
Image has 344 counts for 0.3412 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 150 5 0 0 194
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 150 5 0 0 194
in 1008.10 seconds
Image has 150 counts for 0.1488 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 194 5 0 0 150
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 194 5 0 0 150
in 1008.10 seconds
Image has 194 counts for 0.1924 counts/sec
Command not found; type ? for a command listing
!ad24043000g200470h:ASCA >
!ad24043000g200470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g200470h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g200470h:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g200470h:ASCA-GIS2-PH > set image sky
!ad24043000g200470h:ASCA-GIS2-PH > filter region corner_point.reg
!ad24043000g200470h:ASCA-GIS2-PH > extract image
!ad24043000g200470h:ASCA-GIS2-PH > save image outfile=ad24043000g200470h.img
Wrote image to file ad24043000g200470h.img
!ad24043000g200470h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad24043000g200470h:ASCA-GIS2-PH > extract image
!ad24043000g200470h:ASCA-GIS2-PH > save image outfile=ad24043000g200470h_lo.img
Wrote image to file ad24043000g200470h_lo.img
!ad24043000g200470h:ASCA-GIS2-PH > clear pha_cut
!ad24043000g200470h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g200470h:ASCA-GIS2-PH > extract image
!ad24043000g200470h:ASCA-GIS2-PH > save image outfile=ad24043000g200470h_hi.img
Wrote image to file ad24043000g200470h_hi.img
!ad24043000g200470h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad24043000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad24043000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6619
Mean RA/DEC/ROLL : 85.3755 -2.3358 99.6619
Pnt RA/DEC/ROLL : 85.2597 -2.1813 99.6619
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 109
Total GTI (secs) : 21524.570
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3387.9794922 3387.9794922
20 Percent Complete: Total/live time: 4714.4760742 4714.4760742
30 Percent Complete: Total/live time: 6706.0141602 6706.0141602
40 Percent Complete: Total/live time: 9664.5058594 9664.5058594
50 Percent Complete: Total/live time: 11064.5009766 11064.5009766
60 Percent Complete: Total/live time: 13263.7031250 13263.7031250
70 Percent Complete: Total/live time: 16996.3300781 16996.3300781
80 Percent Complete: Total/live time: 17780.5976562 17780.5976562
90 Percent Complete: Total/live time: 19916.3222656 19916.3222656
100 Percent Complete: Total/live time: 21524.5722656 21524.5722656
Number of attitude steps used: 85
Number of attitude steps avail: 47810
Mean RA/DEC pixel offset: 2.4951 -2.9208
writing expo file: ad24043000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 9263 135 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 9263 135 0 0 0
in 21524.57 seconds
Image has 9263 counts for 0.4303 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 4445 135 0 0 4818
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 4445 135 0 0 4818
in 21524.57 seconds
Image has 4445 counts for 0.2065 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 4855 135 0 0 4408
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 4855 135 0 0 4408
in 21524.57 seconds
Image has 4855 counts for 0.2256 counts/sec
Command not found; type ? for a command listing
!ad24043000g300170h:ASCA >
!ad24043000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g300170h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g300170h:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g300170h:ASCA-GIS3-PH > set image sky
!ad24043000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad24043000g300170h:ASCA-GIS3-PH > extract image
!ad24043000g300170h:ASCA-GIS3-PH > save image outfile=ad24043000g300170h.img
Wrote image to file ad24043000g300170h.img
!ad24043000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad24043000g300170h:ASCA-GIS3-PH > extract image
!ad24043000g300170h:ASCA-GIS3-PH > save image outfile=ad24043000g300170h_lo.img
Wrote image to file ad24043000g300170h_lo.img
!ad24043000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad24043000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g300170h:ASCA-GIS3-PH > extract image
!ad24043000g300170h:ASCA-GIS3-PH > save image outfile=ad24043000g300170h_hi.img
Wrote image to file ad24043000g300170h_hi.img
!ad24043000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad24043000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6598
Mean RA/DEC/ROLL : 85.3692 -2.3292 99.6598
Pnt RA/DEC/ROLL : 85.3592 -2.3177 99.6598
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 46
Total GTI (secs) : 15279.156
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1694.0217285 1694.0217285
20 Percent Complete: Total/live time: 3212.0800781 3212.0800781
30 Percent Complete: Total/live time: 5347.4125977 5347.4125977
40 Percent Complete: Total/live time: 6689.2509766 6689.2509766
50 Percent Complete: Total/live time: 7861.5600586 7861.5600586
60 Percent Complete: Total/live time: 9362.7265625 9362.7265625
70 Percent Complete: Total/live time: 11147.7207031 11147.7207031
80 Percent Complete: Total/live time: 12800.9033203 12800.9033203
90 Percent Complete: Total/live time: 14160.8994141 14160.8994141
100 Percent Complete: Total/live time: 15279.1591797 15279.1591797
Number of attitude steps used: 86
Number of attitude steps avail: 7587
Mean RA/DEC pixel offset: 19.0483 -2.1866
writing expo file: ad24043000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 6538 105 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 6538 105 0 0 0
in 15279.16 seconds
Image has 6538 counts for 0.4279 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 3250 105 0 0 3288
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 3250 105 0 0 3288
in 15279.16 seconds
Image has 3250 counts for 0.2127 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 3304 105 0 0 3234
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 3304 105 0 0 3234
in 15279.16 seconds
Image has 3304 counts for 0.2162 counts/sec
Command not found; type ? for a command listing
!ad24043000g300270m:ASCA >
!ad24043000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g300270m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g300270m:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g300270m:ASCA-GIS3-PH > set image sky
!ad24043000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad24043000g300270m:ASCA-GIS3-PH > extract image
!ad24043000g300270m:ASCA-GIS3-PH > save image outfile=ad24043000g300270m.img
Wrote image to file ad24043000g300270m.img
!ad24043000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad24043000g300270m:ASCA-GIS3-PH > extract image
!ad24043000g300270m:ASCA-GIS3-PH > save image outfile=ad24043000g300270m_lo.img
Wrote image to file ad24043000g300270m_lo.img
!ad24043000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad24043000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g300270m:ASCA-GIS3-PH > extract image
!ad24043000g300270m:ASCA-GIS3-PH > save image outfile=ad24043000g300270m_hi.img
Wrote image to file ad24043000g300270m_hi.img
!ad24043000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad24043000g300370l.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6598
Mean RA/DEC/ROLL : 85.3701 -2.3290 99.6598
Pnt RA/DEC/ROLL : 85.3532 -2.3244 99.6598
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 1
Total GTI (secs) : 17.805
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 14.8052568 14.8052568
20 Percent Complete: Total/live time: 17.8054657 17.8054657
100 Percent Complete: Total/live time: 17.8054657 17.8054657
Number of attitude steps used: 2
Number of attitude steps avail: 23
Mean RA/DEC pixel offset: 1.6390 -1.1406
writing expo file: ad24043000g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g300370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g300370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 3 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 3 0 0 0 0
in 17.81 seconds
Image has 3 counts for 0.1685 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 2 0 0 0 1
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 2 0 0 0 1
in 17.81 seconds
Image has 2 counts for 0.1123 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 0 0 0 2
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 1 0 0 0 2
in 17.81 seconds
Image has 1 counts for 5.6163E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000g300370l:ASCA >
!ad24043000g300370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g300370l:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g300370l:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g300370l:ASCA-GIS3-PH > set image sky
!ad24043000g300370l:ASCA-GIS3-PH > filter region corner_point.reg
!ad24043000g300370l:ASCA-GIS3-PH > extract image
!ad24043000g300370l:ASCA-GIS3-PH > save image outfile=ad24043000g300370l.img
Wrote image to file ad24043000g300370l.img
!ad24043000g300370l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad24043000g300370l:ASCA-GIS3-PH > extract image
!ad24043000g300370l:ASCA-GIS3-PH > save image outfile=ad24043000g300370l_lo.img
Wrote image to file ad24043000g300370l_lo.img
!ad24043000g300370l:ASCA-GIS3-PH > clear pha_cut
!ad24043000g300370l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g300370l:ASCA-GIS3-PH > extract image
!ad24043000g300370l:ASCA-GIS3-PH > save image outfile=ad24043000g300370l_hi.img
Wrote image to file ad24043000g300370l_hi.img
!ad24043000g300370l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad24043000g300470h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000g300470h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6633
Mean RA/DEC/ROLL : 85.3685 -2.3279 99.6633
Pnt RA/DEC/ROLL : 85.3604 -2.3230 99.6633
Image rebin factor : 1
Attitude Records : 68785
GTI intervals : 3
Total GTI (secs) : 1008.096
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 144.4995728 144.4995728
20 Percent Complete: Total/live time: 1008.0959473 1008.0959473
100 Percent Complete: Total/live time: 1008.0959473 1008.0959473
Number of attitude steps used: 3
Number of attitude steps avail: 2235
Mean RA/DEC pixel offset: 1.4771 -1.1526
writing expo file: ad24043000g300470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000g300470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000g300470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 369 4 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 369 4 0 0 0
in 1008.10 seconds
Image has 369 counts for 0.3660 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 175 4 0 0 194
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 175 4 0 0 194
in 1008.10 seconds
Image has 175 counts for 0.1736 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 194 4 0 0 175
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 194 4 0 0 175
in 1008.10 seconds
Image has 194 counts for 0.1924 counts/sec
Command not found; type ? for a command listing
!ad24043000g300470h:ASCA >
!ad24043000g300470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000g300470h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000g300470h:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000g300470h:ASCA-GIS3-PH > set image sky
!ad24043000g300470h:ASCA-GIS3-PH > filter region corner_point.reg
!ad24043000g300470h:ASCA-GIS3-PH > extract image
!ad24043000g300470h:ASCA-GIS3-PH > save image outfile=ad24043000g300470h.img
Wrote image to file ad24043000g300470h.img
!ad24043000g300470h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad24043000g300470h:ASCA-GIS3-PH > extract image
!ad24043000g300470h:ASCA-GIS3-PH > save image outfile=ad24043000g300470h_lo.img
Wrote image to file ad24043000g300470h_lo.img
!ad24043000g300470h:ASCA-GIS3-PH > clear pha_cut
!ad24043000g300470h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad24043000g300470h:ASCA-GIS3-PH > extract image
!ad24043000g300470h:ASCA-GIS3-PH > save image outfile=ad24043000g300470h_hi.img
Wrote image to file ad24043000g300470h_hi.img
!ad24043000g300470h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad24043000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6599
Mean RA/DEC/ROLL : 85.3844 -2.3143 99.6599
Pnt RA/DEC/ROLL : 85.3394 -2.3407 99.6599
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 10
GTI intervals : 114
Total GTI (secs) : 18893.137
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2711.9201660 2711.9201660
20 Percent Complete: Total/live time: 4736.2485352 4736.2485352
30 Percent Complete: Total/live time: 6041.6230469 6041.6230469
40 Percent Complete: Total/live time: 8566.6386719 8566.6386719
50 Percent Complete: Total/live time: 10027.5712891 10027.5712891
60 Percent Complete: Total/live time: 12549.2812500 12549.2812500
70 Percent Complete: Total/live time: 13782.0644531 13782.0644531
80 Percent Complete: Total/live time: 16273.6523438 16273.6523438
90 Percent Complete: Total/live time: 18341.9062500 18341.9062500
100 Percent Complete: Total/live time: 18893.1289062 18893.1289062
Number of attitude steps used: 93
Number of attitude steps avail: 42459
Mean RA/DEC pixel offset: -31.0782 -100.3851
writing expo file: ad24043000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 1726 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1726 1726 0 0 0 0
in 18893.13 seconds
Image has 1726 counts for 9.1356E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 989 0 0 0 737
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1726 989 0 0 0 737
in 18893.13 seconds
Image has 989 counts for 5.2347E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 739 0 0 0 987
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1726 739 0 0 0 987
in 18893.13 seconds
Image has 739 counts for 3.9115E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s000102h:ASCA >
!ad24043000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s000102h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s000102h:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad24043000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad24043000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000102h.img
Wrote image to file ad24043000s000102h.img
!ad24043000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad24043000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000102h_lo.img
Wrote image to file ad24043000s000102h_lo.img
!ad24043000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad24043000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000102h_hi.img
Wrote image to file ad24043000s000102h_hi.img
!ad24043000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6600
Mean RA/DEC/ROLL : 85.3834 -2.3143 99.6600
Pnt RA/DEC/ROLL : 85.3436 -2.3369 99.6600
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 10
GTI intervals : 38
Total GTI (secs) : 12997.723
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1483.0579834 1483.0579834
20 Percent Complete: Total/live time: 2850.1347656 2850.1347656
30 Percent Complete: Total/live time: 4846.3686523 4846.3686523
40 Percent Complete: Total/live time: 5354.3666992 5354.3666992
50 Percent Complete: Total/live time: 6684.5161133 6684.5161133
60 Percent Complete: Total/live time: 9461.7500000 9461.7500000
70 Percent Complete: Total/live time: 9461.7500000 9461.7500000
80 Percent Complete: Total/live time: 10601.7460938 10601.7460938
90 Percent Complete: Total/live time: 12171.9833984 12171.9833984
100 Percent Complete: Total/live time: 12997.7236328 12997.7236328
Number of attitude steps used: 40
Number of attitude steps avail: 7163
Mean RA/DEC pixel offset: 44.8305 -87.7153
writing expo file: ad24043000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 1202 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1202 1202 0 0 0 0
in 12997.72 seconds
Image has 1202 counts for 9.2478E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 701 0 0 0 501
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1202 701 0 0 0 501
in 12997.72 seconds
Image has 701 counts for 5.3933E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 502 0 0 0 700
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1202 502 0 0 0 700
in 12997.72 seconds
Image has 502 counts for 3.8622E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s000202m:ASCA >
!ad24043000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s000202m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s000202m:ASCA > read events ad24043000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad24043000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad24043000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000202m.img
Wrote image to file ad24043000s000202m.img
!ad24043000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad24043000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000202m_lo.img
Wrote image to file ad24043000s000202m_lo.img
!ad24043000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad24043000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000202m_hi.img
Wrote image to file ad24043000s000202m_hi.img
!ad24043000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s000402h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s000402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6683
Mean RA/DEC/ROLL : 85.4082 -2.3400 99.6683
Pnt RA/DEC/ROLL : 85.2459 -2.1962 99.6683
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 4
GTI intervals : 12
Total GTI (secs) : 3377.721
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 830.4816284 830.4816284
20 Percent Complete: Total/live time: 830.4816284 830.4816284
30 Percent Complete: Total/live time: 1326.4484863 1326.4484863
40 Percent Complete: Total/live time: 1547.9478760 1547.9478760
50 Percent Complete: Total/live time: 1779.9157715 1779.9157715
60 Percent Complete: Total/live time: 2979.8154297 2979.8154297
70 Percent Complete: Total/live time: 2979.8154297 2979.8154297
80 Percent Complete: Total/live time: 3377.7204590 3377.7204590
100 Percent Complete: Total/live time: 3377.7204590 3377.7204590
Number of attitude steps used: 10
Number of attitude steps avail: 7324
Mean RA/DEC pixel offset: -42.0597 -119.1479
writing expo file: ad24043000s000402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s000402h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s000402h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 257 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257 257 0 0 0 0
in 3377.72 seconds
Image has 257 counts for 7.6087E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 164 0 0 0 93
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257 164 0 0 0 93
in 3377.72 seconds
Image has 164 counts for 4.8553E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 93 0 0 0 164
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257 93 0 0 0 164
in 3377.72 seconds
Image has 93 counts for 2.7533E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s000402h:ASCA >
!ad24043000s000402h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s000402h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s000402h:ASCA > read events ad24043000s000402h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s000402h:ASCA-SIS0-BRIGHT > set image sky
!ad24043000s000402h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad24043000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000402h.img
Wrote image to file ad24043000s000402h.img
!ad24043000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad24043000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000402h_lo.img
Wrote image to file ad24043000s000402h_lo.img
!ad24043000s000402h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad24043000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad24043000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad24043000s000402h_hi.img
Wrote image to file ad24043000s000402h_hi.img
!ad24043000s000402h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6606
Mean RA/DEC/ROLL : 85.3685 -2.3161 99.6606
Pnt RA/DEC/ROLL : 85.3552 -2.3385 99.6606
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 26
GTI intervals : 110
Total GTI (secs) : 18907.168
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2683.9204102 2683.9204102
20 Percent Complete: Total/live time: 4706.2802734 4706.2802734
30 Percent Complete: Total/live time: 6011.6547852 6011.6547852
40 Percent Complete: Total/live time: 8540.6708984 8540.6708984
50 Percent Complete: Total/live time: 9993.6035156 9993.6035156
60 Percent Complete: Total/live time: 12565.2197266 12565.2197266
70 Percent Complete: Total/live time: 13798.0029297 13798.0029297
80 Percent Complete: Total/live time: 16289.5917969 16289.5917969
90 Percent Complete: Total/live time: 18355.9394531 18355.9394531
100 Percent Complete: Total/live time: 18907.1621094 18907.1621094
Number of attitude steps used: 89
Number of attitude steps avail: 42424
Mean RA/DEC pixel offset: -34.8621 -28.3477
writing expo file: ad24043000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 1615 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1615 1615 0 0 0 0
in 18907.16 seconds
Image has 1615 counts for 8.5417E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 861 0 0 0 754
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1615 861 0 0 0 754
in 18907.16 seconds
Image has 861 counts for 4.5538E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 755 0 0 0 860
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1615 755 0 0 0 860
in 18907.16 seconds
Image has 755 counts for 3.9932E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s100102h:ASCA >
!ad24043000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s100102h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s100102h:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad24043000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad24043000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100102h.img
Wrote image to file ad24043000s100102h.img
!ad24043000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad24043000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100102h_lo.img
Wrote image to file ad24043000s100102h_lo.img
!ad24043000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad24043000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100102h_hi.img
Wrote image to file ad24043000s100102h_hi.img
!ad24043000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6607
Mean RA/DEC/ROLL : 85.3676 -2.3161 99.6607
Pnt RA/DEC/ROLL : 85.3594 -2.3352 99.6607
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 28
GTI intervals : 37
Total GTI (secs) : 12983.973
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1483.0579834 1483.0579834
20 Percent Complete: Total/live time: 2850.1347656 2850.1347656
30 Percent Complete: Total/live time: 4846.3686523 4846.3686523
40 Percent Complete: Total/live time: 5354.3666992 5354.3666992
50 Percent Complete: Total/live time: 6652.5161133 6652.5161133
60 Percent Complete: Total/live time: 9429.7500000 9429.7500000
70 Percent Complete: Total/live time: 9429.7500000 9429.7500000
80 Percent Complete: Total/live time: 10569.7460938 10569.7460938
90 Percent Complete: Total/live time: 12158.2333984 12158.2333984
100 Percent Complete: Total/live time: 12983.9736328 12983.9736328
Number of attitude steps used: 40
Number of attitude steps avail: 7163
Mean RA/DEC pixel offset: 40.3862 -15.8644
writing expo file: ad24043000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 1034 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 1034 0 0 0 0
in 12983.97 seconds
Image has 1034 counts for 7.9637E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 545 0 0 0 489
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 545 0 0 0 489
in 12983.97 seconds
Image has 545 counts for 4.1975E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 490 0 0 0 544
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 490 0 0 0 544
in 12983.97 seconds
Image has 490 counts for 3.7739E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s100202m:ASCA >
!ad24043000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s100202m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s100202m:ASCA > read events ad24043000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad24043000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad24043000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100202m.img
Wrote image to file ad24043000s100202m.img
!ad24043000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad24043000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100202m_lo.img
Wrote image to file ad24043000s100202m_lo.img
!ad24043000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad24043000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100202m_hi.img
Wrote image to file ad24043000s100202m_hi.img
!ad24043000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s100402h.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s100402h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6688
Mean RA/DEC/ROLL : 85.3928 -2.3425 99.6688
Pnt RA/DEC/ROLL : 85.2618 -2.1944 99.6688
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 15
GTI intervals : 8
Total GTI (secs) : 3511.751
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 400.9832764 400.9832764
20 Percent Complete: Total/live time: 926.4816284 926.4816284
30 Percent Complete: Total/live time: 1458.4484863 1458.4484863
40 Percent Complete: Total/live time: 1458.4484863 1458.4484863
50 Percent Complete: Total/live time: 1911.9157715 1911.9157715
60 Percent Complete: Total/live time: 3083.8151855 3083.8151855
70 Percent Complete: Total/live time: 3083.8151855 3083.8151855
80 Percent Complete: Total/live time: 3511.7514648 3511.7514648
100 Percent Complete: Total/live time: 3511.7514648 3511.7514648
Number of attitude steps used: 10
Number of attitude steps avail: 7388
Mean RA/DEC pixel offset: -46.0674 -54.4368
writing expo file: ad24043000s100402h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s100402h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s100402h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 281 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
281 281 0 0 0 0
in 3511.75 seconds
Image has 281 counts for 8.0017E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 152 0 0 0 129
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
281 152 0 0 0 129
in 3511.75 seconds
Image has 152 counts for 4.3283E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 129 0 0 0 152
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
281 129 0 0 0 152
in 3511.75 seconds
Image has 129 counts for 3.6734E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s100402h:ASCA >
!ad24043000s100402h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s100402h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s100402h:ASCA > read events ad24043000s100402h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s100402h:ASCA-SIS1-BRIGHT > set image sky
!ad24043000s100402h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad24043000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100402h.img
Wrote image to file ad24043000s100402h.img
!ad24043000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad24043000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100402h_lo.img
Wrote image to file ad24043000s100402h_lo.img
!ad24043000s100402h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad24043000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100402h_hi.img
Wrote image to file ad24043000s100402h_hi.img
!ad24043000s100402h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad24043000s100502m.expo
ASCAEXPO_V0.9b
reading data file: ad24043000s100502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960301_0512.0500
making an exposure map...
Aspect RA/DEC/ROLL : 85.3641 -2.3244 99.6537
Mean RA/DEC/ROLL : 85.3677 -2.3157 99.6537
Pnt RA/DEC/ROLL : 85.3601 -2.3303 99.6537
Image rebin factor : 4
Attitude Records : 68785
Hot Pixels : 13
GTI intervals : 2
Total GTI (secs) : 1444.022
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 214.9929352 214.9929352
20 Percent Complete: Total/live time: 382.9994507 382.9994507
30 Percent Complete: Total/live time: 478.9991760 478.9991760
40 Percent Complete: Total/live time: 666.9986572 666.9986572
50 Percent Complete: Total/live time: 958.9976807 958.9976807
60 Percent Complete: Total/live time: 958.9976807 958.9976807
70 Percent Complete: Total/live time: 1150.9969482 1150.9969482
80 Percent Complete: Total/live time: 1402.9960938 1402.9960938
90 Percent Complete: Total/live time: 1402.9960938 1402.9960938
100 Percent Complete: Total/live time: 1444.0217285 1444.0217285
Number of attitude steps used: 19
Number of attitude steps avail: 445
Mean RA/DEC pixel offset: -43.8069 -34.3497
writing expo file: ad24043000s100502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad24043000s100502m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad24043000s100502m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 113 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
113 113 0 0 0 0
in 1444.02 seconds
Image has 113 counts for 7.8254E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 48 0 0 0 65
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
113 48 0 0 0 65
in 1444.02 seconds
Image has 48 counts for 3.3240E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 65 0 0 0 48
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
113 65 0 0 0 48
in 1444.02 seconds
Image has 65 counts for 4.5013E-02 counts/sec
Command not found; type ? for a command listing
!ad24043000s100502m:ASCA >
!ad24043000s100502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad24043000s100502m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!ad24043000s100502m:ASCA > read events ad24043000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!ad24043000s100502m:ASCA-SIS1-BRIGHT > set image sky
!ad24043000s100502m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad24043000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100502m.img
Wrote image to file ad24043000s100502m.img
!ad24043000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad24043000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100502m_lo.img
Wrote image to file ad24043000s100502m_lo.img
!ad24043000s100502m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad24043000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad24043000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad24043000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad24043000s100502m_hi.img
Wrote image to file ad24043000s100502m_hi.img
!ad24043000s100502m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad24043000s000102h.expo ad24043000s000202m.expo ad24043000s000402h.expo ad24043000s100102h.expo ad24043000s100202m.expo ad24043000s100402h.expo ad24043000s100502m.expo-> Summing the following images to produce ad24043000sis32002_all.totsky
ad24043000s000102h.img ad24043000s000202m.img ad24043000s000402h.img ad24043000s100102h.img ad24043000s100202m.img ad24043000s100402h.img ad24043000s100502m.img-> Summing the following images to produce ad24043000sis32002_lo.totsky
ad24043000s000102h_lo.img ad24043000s000202m_lo.img ad24043000s000402h_lo.img ad24043000s100102h_lo.img ad24043000s100202m_lo.img ad24043000s100402h_lo.img ad24043000s100502m_lo.img-> Summing the following images to produce ad24043000sis32002_hi.totsky
ad24043000s000102h_hi.img ad24043000s000202m_hi.img ad24043000s000402h_hi.img ad24043000s100102h_hi.img ad24043000s100202m_hi.img ad24043000s100402h_hi.img ad24043000s100502m_hi.img-> Running XIMAGE to create ad24043000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad24043000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 19.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 19 min: 0 ![2]XIMAGE> read/exp_map ad24043000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 1201.92 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1201 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 22 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 14.0000 14 0 ![9]XIMAGE> exit-> Summing gis images
ad24043000g200170h.expo ad24043000g200270m.expo ad24043000g200370l.expo ad24043000g200470h.expo ad24043000g300170h.expo ad24043000g300270m.expo ad24043000g300370l.expo ad24043000g300470h.expo-> Summing the following images to produce ad24043000gis25670_all.totsky
ad24043000g200170h.img ad24043000g200270m.img ad24043000g200370l.img ad24043000g200470h.img ad24043000g300170h.img ad24043000g300270m.img ad24043000g300370l.img ad24043000g300470h.img-> Summing the following images to produce ad24043000gis25670_lo.totsky
ad24043000g200170h_lo.img ad24043000g200270m_lo.img ad24043000g200370l_lo.img ad24043000g200470h_lo.img ad24043000g300170h_lo.img ad24043000g300270m_lo.img ad24043000g300370l_lo.img ad24043000g300470h_lo.img-> Summing the following images to produce ad24043000gis25670_hi.totsky
ad24043000g200170h_hi.img ad24043000g200270m_hi.img ad24043000g200370l_hi.img ad24043000g200470h_hi.img ad24043000g300170h_hi.img ad24043000g300270m_hi.img ad24043000g300370l_hi.img ad24043000g300470h_hi.img-> Running XIMAGE to create ad24043000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad24043000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 26.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 26 min: 0 ![2]XIMAGE> read/exp_map ad24043000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1262.45 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1262 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 51.0000 51 0 ![9]XIMAGE> exit
193 72 0.000413329 23 8 30.5472 132 116 0.000164289 14 9 12.8901 111 140 0.000127617 13 10 9.46588 160 212 6.44476e-05 26 20 5.90509 119 212 5.07881e-05 14 12 4.24204-> Smoothing ad24043000gis25670_hi.totsky with ad24043000gis25670.totexpo
193 72 0.000247371 17 6 34.3519 132 117 9.82801e-05 14 9 14.0348 113 140 3.48527e-05 13 9 4.99694 106 193 2.79878e-05 10 7 4.24005 158 211 2.6162e-05 19 8 4.17231-> Smoothing ad24043000gis25670_lo.totsky with ad24043000gis25670.totexpo
193 73 0.000186935 31 9 31.6109 111 140 8.50783e-05 18 9 13.1973 133 115 8.06777e-05 13 8 14.326 160 212 3.73625e-05 24 25 8.13128 155 133 3.01001e-05 10 9 6.01852 115 192 2.9044e-05 10 11 5.98351-> Determining extraction radii
193 72 23 F 132 116 14 F 111 140 13 F 160 212 24 T 119 212 14 T 106 193 9 F 155 133 10 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad24043000gis25670.src
118 186 0.000130963 29 8 25.4665 128 245 5.26939e-05 30 10 11.0928-> Smoothing ad24043000sis32002_hi.totsky with ad24043000sis32002.totexpo
118 186 2.09415e-05 35 15 8.33532-> Smoothing ad24043000sis32002_lo.totsky with ad24043000sis32002.totexpo
118 186 9.39851e-05 28 8 42.251 128 245 3.93817e-05 30 9 22.9761-> Determining extraction radii
118 186 29 F 128 245 30 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad24043000sis32002.src
The sum of the selected column is 3862.0000 The mean of the selected column is 551.71429 The standard deviation of the selected column is 3.5923199 The minimum of selected column is 547.00000 The maximum of selected column is 555.00000 The number of points used in calculation is 7-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2837.0000 The mean of the selected column is 405.28571 The standard deviation of the selected column is 5.9080252 The minimum of selected column is 396.00000 The maximum of selected column is 412.00000 The number of points used in calculation is 7-> Converting (512.0,980.0,2.0) to s0 detector coordinates
The sum of the selected column is 1248.0000 The mean of the selected column is 312.00000 The standard deviation of the selected column is 2.1602469 The minimum of selected column is 309.00000 The maximum of selected column is 314.00000 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1639.0000 The mean of the selected column is 409.75000 The standard deviation of the selected column is 4.3493295 The minimum of selected column is 406.00000 The maximum of selected column is 414.00000 The number of points used in calculation is 4-> Converting (472.0,744.0,2.0) to s1 detector coordinates
The sum of the selected column is 2193.0000 The mean of the selected column is 548.25000 The standard deviation of the selected column is 4.9916597 The minimum of selected column is 544.00000 The maximum of selected column is 555.00000 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1750.0000 The mean of the selected column is 437.50000 The standard deviation of the selected column is 13.964240 The minimum of selected column is 424.00000 The maximum of selected column is 451.00000 The number of points used in calculation is 4-> Converting (512.0,980.0,2.0) to s1 detector coordinates
The sum of the selected column is 313.00000 The mean of the selected column is 313.00000 The standard deviation of the selected column is undefined The minimum of selected column is 313.00000 The maximum of selected column is 313.00000 The number of points used in calculation is 1-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 443.00000 The mean of the selected column is 443.00000 The standard deviation of the selected column is undefined The minimum of selected column is 443.00000 The maximum of selected column is 443.00000 The number of points used in calculation is 1-> Converting (193.0,72.0,2.0) to g2 detector coordinates
The sum of the selected column is 77512.000 The mean of the selected column is 170.35604 The standard deviation of the selected column is 11.469969 The minimum of selected column is 146.00000 The maximum of selected column is 190.00000 The number of points used in calculation is 455-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 86094.000 The mean of the selected column is 189.21758 The standard deviation of the selected column is 5.1217467 The minimum of selected column is 176.00000 The maximum of selected column is 202.00000 The number of points used in calculation is 455-> Converting (132.0,116.0,2.0) to g2 detector coordinates
The sum of the selected column is 10927.000 The mean of the selected column is 136.58750 The standard deviation of the selected column is 1.1874209 The minimum of selected column is 133.00000 The maximum of selected column is 139.00000 The number of points used in calculation is 80-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10587.000 The mean of the selected column is 132.33750 The standard deviation of the selected column is 1.3589250 The minimum of selected column is 129.00000 The maximum of selected column is 135.00000 The number of points used in calculation is 80-> Converting (111.0,140.0,2.0) to g2 detector coordinates
The sum of the selected column is 6633.0000 The mean of the selected column is 116.36842 The standard deviation of the selected column is 1.1437966 The minimum of selected column is 114.00000 The maximum of selected column is 119.00000 The number of points used in calculation is 57-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6137.0000 The mean of the selected column is 107.66667 The standard deviation of the selected column is 1.4057704 The minimum of selected column is 105.00000 The maximum of selected column is 110.00000 The number of points used in calculation is 57-> Converting (160.0,212.0,2.0) to g2 detector coordinates
The sum of the selected column is 19787.000 The mean of the selected column is 50.735897 The standard deviation of the selected column is 4.7976530 The minimum of selected column is 41.000000 The maximum of selected column is 61.000000 The number of points used in calculation is 390-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 55746.000 The mean of the selected column is 142.93846 The standard deviation of the selected column is 10.152630 The minimum of selected column is 121.00000 The maximum of selected column is 163.00000 The number of points used in calculation is 390-> Converting (119.0,212.0,2.0) to g2 detector coordinates
The sum of the selected column is 230.00000 The mean of the selected column is 46.000000 The standard deviation of the selected column is 0.70710678 The minimum of selected column is 45.000000 The maximum of selected column is 47.000000 The number of points used in calculation is 5-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 517.00000 The mean of the selected column is 103.40000 The standard deviation of the selected column is 0.89442719 The minimum of selected column is 102.00000 The maximum of selected column is 104.00000 The number of points used in calculation is 5-> Converting (106.0,193.0,2.0) to g2 detector coordinates
The sum of the selected column is 1046.0000 The mean of the selected column is 65.375000 The standard deviation of the selected column is 1.5864005 The minimum of selected column is 63.000000 The maximum of selected column is 68.000000 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1504.0000 The mean of the selected column is 94.000000 The standard deviation of the selected column is 0.96609178 The minimum of selected column is 92.000000 The maximum of selected column is 96.000000 The number of points used in calculation is 16-> Converting (155.0,133.0,2.0) to g2 detector coordinates
The sum of the selected column is 2092.0000 The mean of the selected column is 116.22222 The standard deviation of the selected column is 1.3527991 The minimum of selected column is 114.00000 The maximum of selected column is 118.00000 The number of points used in calculation is 18-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2743.0000 The mean of the selected column is 152.38889 The standard deviation of the selected column is 1.0369009 The minimum of selected column is 150.00000 The maximum of selected column is 154.00000 The number of points used in calculation is 18-> Converting (193.0,72.0,2.0) to g3 detector coordinates
The sum of the selected column is 36801.000 The mean of the selected column is 176.08134 The standard deviation of the selected column is 1.0552461 The minimum of selected column is 173.00000 The maximum of selected column is 178.00000 The number of points used in calculation is 209-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 41917.000 The mean of the selected column is 200.55981 The standard deviation of the selected column is 1.1592073 The minimum of selected column is 197.00000 The maximum of selected column is 203.00000 The number of points used in calculation is 209-> Converting (132.0,116.0,2.0) to g3 detector coordinates
The sum of the selected column is 13400.000 The mean of the selected column is 142.55319 The standard deviation of the selected column is 1.0738036 The minimum of selected column is 140.00000 The maximum of selected column is 145.00000 The number of points used in calculation is 94-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12510.000 The mean of the selected column is 133.08511 The standard deviation of the selected column is 1.3885831 The minimum of selected column is 129.00000 The maximum of selected column is 136.00000 The number of points used in calculation is 94-> Converting (111.0,140.0,2.0) to g3 detector coordinates
The sum of the selected column is 7599.0000 The mean of the selected column is 122.56452 The standard deviation of the selected column is 1.0499175 The minimum of selected column is 120.00000 The maximum of selected column is 124.00000 The number of points used in calculation is 62-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6700.0000 The mean of the selected column is 108.06452 The standard deviation of the selected column is 1.3774646 The minimum of selected column is 105.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 62-> Converting (160.0,212.0,2.0) to g3 detector coordinates
The sum of the selected column is 436.00000 The mean of the selected column is 43.600000 The standard deviation of the selected column is 1.1737878 The minimum of selected column is 42.000000 The maximum of selected column is 46.000000 The number of points used in calculation is 10-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1444.0000 The mean of the selected column is 144.40000 The standard deviation of the selected column is 1.1737878 The minimum of selected column is 143.00000 The maximum of selected column is 146.00000 The number of points used in calculation is 10-> Converting (119.0,212.0,2.0) to g3 detector coordinates
The sum of the selected column is 1106.0000 The mean of the selected column is 50.272727 The standard deviation of the selected column is 1.1621744 The minimum of selected column is 48.000000 The maximum of selected column is 52.000000 The number of points used in calculation is 22-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2292.0000 The mean of the selected column is 104.18182 The standard deviation of the selected column is 1.3675269 The minimum of selected column is 101.00000 The maximum of selected column is 107.00000 The number of points used in calculation is 22-> Converting (106.0,193.0,2.0) to g3 detector coordinates
The sum of the selected column is 2066.0000 The mean of the selected column is 71.241379 The standard deviation of the selected column is 1.2146479 The minimum of selected column is 68.000000 The maximum of selected column is 73.000000 The number of points used in calculation is 29-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2724.0000 The mean of the selected column is 93.931034 The standard deviation of the selected column is 1.3344618 The minimum of selected column is 91.000000 The maximum of selected column is 96.000000 The number of points used in calculation is 29-> Converting (155.0,133.0,2.0) to g3 detector coordinates
The sum of the selected column is 2932.0000 The mean of the selected column is 122.16667 The standard deviation of the selected column is 0.91683134 The minimum of selected column is 120.00000 The maximum of selected column is 124.00000 The number of points used in calculation is 24-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3669.0000 The mean of the selected column is 152.87500 The standard deviation of the selected column is 1.4237886 The minimum of selected column is 151.00000 The maximum of selected column is 156.00000 The number of points used in calculation is 24
1 ad24043000s000102h.evt 3185 1 ad24043000s000202m.evt 3185 1 ad24043000s000402h.evt 3185-> Fetching SIS0_NOTCHIP0.1
ad24043000s000102h.evt ad24043000s000202m.evt ad24043000s000402h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 735 991 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 473 729 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 117 140 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3185 1325 1860 0 0 0
in 35268.57 seconds
Spectrum has 1325 counts for 3.7569E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35269. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.40918E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad24043000s010102_1.pi group=yes
Wrote spectrum to ad24043000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad24043000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 35269. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.40918E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 24 are grouped by a factor 9 ... 25 - 28 are grouped by a factor 4 ... 29 - 34 are grouped by a factor 2 ... 35 - 35 are single channels ... 36 - 51 are grouped by a factor 2 ... 52 - 54 are grouped by a factor 3 ... 55 - 56 are grouped by a factor 2 ... 57 - 64 are grouped by a factor 4 ... 65 - 69 are grouped by a factor 5 ... 70 - 75 are grouped by a factor 6 ... 76 - 83 are grouped by a factor 8 ... 84 - 95 are grouped by a factor 12 ... 96 - 112 are grouped by a factor 17 ... 113 - 136 are grouped by a factor 24 ... 137 - 172 are grouped by a factor 36 ... 173 - 228 are grouped by a factor 56 ... 229 - 355 are grouped by a factor 127 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s010102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 26 by 31 bins
expanded to 26 by 31 bins
First WMAP bin is at detector pixel 440 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 27.761 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 547.00 415.00 (detector coordinates)
Point source at 14.47 18.00 (WMAP bins wrt optical axis)
Point source at 4.90 51.22 (... in polar coordinates)
Total counts in region = 1.29500E+03
Weighted mean angle from optical axis = 4.828 arcmin
-> Extracting ad24043000s010102_2.pi from ad24043000s032002_2.reg and:ad24043000s000102h.evt ad24043000s000202m.evt ad24043000s000402h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 393 1333 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 301 901 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 44 213 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3185 738 2447 0 0 0
in 35268.57 seconds
Spectrum has 738 counts for 2.0925E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35269. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.69336E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s010102_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad24043000s010102_2.pi group=yes
Wrote spectrum to ad24043000s010102_2.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad24043000s010102_2.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 35269. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.69336E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 25 are grouped by a factor 10 ... 26 - 33 are grouped by a factor 4 ... 34 - 36 are grouped by a factor 3 ... 37 - 44 are grouped by a factor 4 ... 45 - 49 are grouped by a factor 5 ... 50 - 55 are grouped by a factor 6 ... 56 - 62 are grouped by a factor 7 ... 63 - 74 are grouped by a factor 12 ... 75 - 91 are grouped by a factor 17 ... 92 - 110 are grouped by a factor 19 ... 111 - 142 are grouped by a factor 32 ... 143 - 230 are grouped by a factor 88 ... 231 - 393 are grouped by a factor 163 ... 394 - 505 are grouped by a factor 112 ... 506 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s010102_2.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s010102_2.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 28 by 32 bins
expanded to 28 by 32 bins
First WMAP bin is at detector pixel 224 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 31.036 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 339.00 419.00 (detector coordinates)
Point source at 40.47 17.50 (WMAP bins wrt optical axis)
Point source at 9.35 23.39 (... in polar coordinates)
Total counts in region = 7.19000E+02
Weighted mean angle from optical axis = 9.722 arcmin
-> Standard Output From STOOL group_event_files:1 ad24043000s000112h.evt 3372 1 ad24043000s000212m.evt 3372 1 ad24043000s000412h.evt 3372-> SIS0_NOTCHIP0.1 already present in current directory
ad24043000s000112h.evt ad24043000s000212m.evt ad24043000s000412h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.34E+04 275 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.evt
Total Good Bad: Region Time Phase Cut
1830 754 1076 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.evt
Total Good Bad: Region Time Phase Cut
1267 492 775 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.evt
Total Good Bad: Region Time Phase Cut
275 120 155 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3372 1366 2006 0 0 0
in 35268.57 seconds
Spectrum has 1366 counts for 3.8731E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35269. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.40918E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s010212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad24043000s000212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad24043000s000412h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad24043000s010212_1.pi group=yes
Wrote spectrum to ad24043000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad24043000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 35269. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.40918E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 49 are grouped by a factor 18 ... 50 - 57 are grouped by a factor 8 ... 58 - 61 are grouped by a factor 4 ... 62 - 63 are grouped by a factor 2 ... 64 - 69 are grouped by a factor 3 ... 70 - 71 are grouped by a factor 2 ... 72 - 77 are grouped by a factor 3 ... 78 - 81 are grouped by a factor 4 ... 82 - 84 are grouped by a factor 3 ... 85 - 100 are grouped by a factor 4 ... 101 - 115 are grouped by a factor 5 ... 116 - 123 are grouped by a factor 8 ... 124 - 130 are grouped by a factor 7 ... 131 - 140 are grouped by a factor 10 ... 141 - 172 are grouped by a factor 16 ... 173 - 198 are grouped by a factor 26 ... 199 - 237 are grouped by a factor 39 ... 238 - 283 are grouped by a factor 46 ... 284 - 370 are grouped by a factor 87 ... 371 - 486 are grouped by a factor 116 ... 487 - 774 are grouped by a factor 288 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s010212_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 26 by 31 bins
expanded to 26 by 31 bins
First WMAP bin is at detector pixel 440 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 27.761 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 547.00 415.00 (detector coordinates)
Point source at 14.47 18.00 (WMAP bins wrt optical axis)
Point source at 4.90 51.22 (... in polar coordinates)
Total counts in region = 1.33900E+03
Weighted mean angle from optical axis = 4.843 arcmin
-> Extracting ad24043000s010212_2.pi from ad24043000s032002_2.reg and:ad24043000s000112h.evt ad24043000s000212m.evt ad24043000s000412h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.34E+04 275 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.evt
Total Good Bad: Region Time Phase Cut
1830 424 1406 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.evt
Total Good Bad: Region Time Phase Cut
1267 315 952 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.evt
Total Good Bad: Region Time Phase Cut
275 48 227 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3372 787 2585 0 0 0
in 35268.57 seconds
Spectrum has 787 counts for 2.2314E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35269. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.69336E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s010212_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad24043000s000212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad24043000s000412h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad24043000s010212_2.pi group=yes
Wrote spectrum to ad24043000s010212_2.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad24043000s010212_2.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 35269. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.69336E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 50 are grouped by a factor 19 ... 51 - 57 are grouped by a factor 7 ... 58 - 62 are grouped by a factor 5 ... 63 - 68 are grouped by a factor 6 ... 69 - 82 are grouped by a factor 7 ... 83 - 91 are grouped by a factor 9 ... 92 - 101 are grouped by a factor 10 ... 102 - 113 are grouped by a factor 12 ... 114 - 130 are grouped by a factor 17 ... 131 - 155 are grouped by a factor 25 ... 156 - 190 are grouped by a factor 35 ... 191 - 242 are grouped by a factor 52 ... 243 - 321 are grouped by a factor 79 ... 322 - 503 are grouped by a factor 182 ... 504 - 765 are grouped by a factor 262 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s010212_2.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s010212_2.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 28 by 32 bins
expanded to 28 by 32 bins
First WMAP bin is at detector pixel 224 288
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 31.036 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 339.00 419.00 (detector coordinates)
Point source at 40.47 17.50 (WMAP bins wrt optical axis)
Point source at 9.35 23.39 (... in polar coordinates)
Total counts in region = 7.67000E+02
Weighted mean angle from optical axis = 9.726 arcmin
-> Standard Output From STOOL group_event_files:1 ad24043000s100102h.evt 3043 1 ad24043000s100202m.evt 3043 1 ad24043000s100402h.evt 3043 1 ad24043000s100502m.evt 3043-> Fetching SIS1_NOTCHIP0.1
ad24043000s100102h.evt ad24043000s100202m.evt ad24043000s100402h.evt ad24043000s100502m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
4 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 605 1010 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 382 652 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 129 152 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 38 75 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3043 1154 1889 0 0 0
in 36846.91 seconds
Spectrum has 1154 counts for 3.1319E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36847. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.47363E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad24043000s110102_1.pi group=yes
Wrote spectrum to ad24043000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad24043000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36847. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.47363E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 27 are grouped by a factor 12 ... 28 - 30 are grouped by a factor 3 ... 31 - 38 are grouped by a factor 2 ... 39 - 41 are grouped by a factor 3 ... 42 - 47 are grouped by a factor 2 ... 48 - 53 are grouped by a factor 3 ... 54 - 61 are grouped by a factor 4 ... 62 - 66 are grouped by a factor 5 ... 67 - 76 are grouped by a factor 10 ... 77 - 85 are grouped by a factor 9 ... 86 - 98 are grouped by a factor 13 ... 99 - 112 are grouped by a factor 14 ... 113 - 133 are grouped by a factor 21 ... 134 - 174 are grouped by a factor 41 ... 175 - 246 are grouped by a factor 72 ... 247 - 358 are grouped by a factor 112 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s110102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 27 by 31 bins
expanded to 27 by 31 bins
First WMAP bin is at detector pixel 432 320
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 28.504 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 543.00 447.00 (detector coordinates)
Point source at 9.41 40.85 (WMAP bins wrt optical axis)
Point source at 8.89 77.03 (... in polar coordinates)
Total counts in region = 1.13100E+03
Weighted mean angle from optical axis = 8.711 arcmin
-> Extracting ad24043000s110102_2.pi from ad24043000s132002_2.reg and:ad24043000s100102h.evt ad24043000s100202m.evt ad24043000s100402h.evt ad24043000s100502m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
4 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 415 1200 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 307 727 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 45 236 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 18 95 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3043 785 2258 0 0 0
in 36846.91 seconds
Spectrum has 785 counts for 2.1304E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36847. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.66699E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s110102_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad24043000s110102_2.pi group=yes
Wrote spectrum to ad24043000s110102_2.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad24043000s110102_2.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36847. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.66699E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 25 are grouped by a factor 10 ... 26 - 30 are grouped by a factor 5 ... 31 - 36 are grouped by a factor 3 ... 37 - 44 are grouped by a factor 4 ... 45 - 49 are grouped by a factor 5 ... 50 - 55 are grouped by a factor 6 ... 56 - 63 are grouped by a factor 8 ... 64 - 72 are grouped by a factor 9 ... 73 - 90 are grouped by a factor 18 ... 91 - 109 are grouped by a factor 19 ... 110 - 147 are grouped by a factor 38 ... 148 - 198 are grouped by a factor 51 ... 199 - 318 are grouped by a factor 120 ... 319 - 448 are grouped by a factor 130 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s110102_2.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s110102_2.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 28 by 31 bins
expanded to 28 by 31 bins
First WMAP bin is at detector pixel 224 328
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 30.732 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 339.00 455.00 (detector coordinates)
Point source at 34.91 39.85 (WMAP bins wrt optical axis)
Point source at 11.24 48.78 (... in polar coordinates)
Total counts in region = 7.65000E+02
Weighted mean angle from optical axis = 11.454 arcmin
-> Standard Output From STOOL group_event_files:1 ad24043000s100112h.evt 3181 1 ad24043000s100212m.evt 3181 1 ad24043000s100412h.evt 3181 1 ad24043000s100512m.evt 3181-> SIS1_NOTCHIP0.1 already present in current directory
ad24043000s100112h.evt ad24043000s100212m.evt ad24043000s100412h.evt ad24043000s100512m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
4 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.14E+04 120 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.evt
Total Good Bad: Region Time Phase Cut
1689 624 1065 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.evt
Total Good Bad: Region Time Phase Cut
1075 394 681 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.evt
Total Good Bad: Region Time Phase Cut
297 134 163 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.evt
Total Good Bad: Region Time Phase Cut
120 39 81 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3181 1191 1990 0 0 0
in 36846.91 seconds
Spectrum has 1191 counts for 3.2323E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36847. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.47363E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s110212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100412h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100512m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad24043000s110212_1.pi group=yes
Wrote spectrum to ad24043000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad24043000s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36847. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.47363E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 54 are grouped by a factor 22 ... 55 - 60 are grouped by a factor 6 ... 61 - 96 are grouped by a factor 4 ... 97 - 102 are grouped by a factor 6 ... 103 - 107 are grouped by a factor 5 ... 108 - 115 are grouped by a factor 8 ... 116 - 122 are grouped by a factor 7 ... 123 - 131 are grouped by a factor 9 ... 132 - 148 are grouped by a factor 17 ... 149 - 166 are grouped by a factor 18 ... 167 - 192 are grouped by a factor 26 ... 193 - 214 are grouped by a factor 22 ... 215 - 254 are grouped by a factor 40 ... 255 - 324 are grouped by a factor 70 ... 325 - 442 are grouped by a factor 118 ... 443 - 630 are grouped by a factor 188 ... 631 - 877 are grouped by a factor 247 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s110212_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 27 by 31 bins
expanded to 27 by 31 bins
First WMAP bin is at detector pixel 432 320
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 28.504 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 543.00 447.00 (detector coordinates)
Point source at 9.41 40.85 (WMAP bins wrt optical axis)
Point source at 8.89 77.03 (... in polar coordinates)
Total counts in region = 1.16700E+03
Weighted mean angle from optical axis = 8.724 arcmin
-> Extracting ad24043000s110212_2.pi from ad24043000s132002_2.reg and:ad24043000s100112h.evt ad24043000s100212m.evt ad24043000s100412h.evt ad24043000s100512m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
2 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
3 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
4 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.14E+04 120 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.evt
Total Good Bad: Region Time Phase Cut
1689 437 1252 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.evt
Total Good Bad: Region Time Phase Cut
1075 313 762 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.evt
Total Good Bad: Region Time Phase Cut
297 48 249 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.evt
Total Good Bad: Region Time Phase Cut
120 22 98 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3181 820 2361 0 0 0
in 36846.91 seconds
Spectrum has 820 counts for 2.2254E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 36847. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.66699E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000s110212_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100412h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad24043000s100512m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad24043000s110212_2.pi group=yes
Wrote spectrum to ad24043000s110212_2.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad24043000s110212_2.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 36847. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.66699E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 50 are grouped by a factor 18 ... 51 - 60 are grouped by a factor 10 ... 61 - 66 are grouped by a factor 6 ... 67 - 71 are grouped by a factor 5 ... 72 - 77 are grouped by a factor 6 ... 78 - 93 are grouped by a factor 8 ... 94 - 103 are grouped by a factor 10 ... 104 - 117 are grouped by a factor 14 ... 118 - 132 are grouped by a factor 15 ... 133 - 151 are grouped by a factor 19 ... 152 - 187 are grouped by a factor 36 ... 188 - 234 are grouped by a factor 47 ... 235 - 307 are grouped by a factor 73 ... 308 - 438 are grouped by a factor 131 ... 439 - 672 are grouped by a factor 234 ... 673 - 884 are grouped by a factor 212 ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000s110212_2.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad24043000s110212_2.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 28 by 31 bins
expanded to 28 by 31 bins
First WMAP bin is at detector pixel 224 328
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 30.732 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 339.00 455.00 (detector coordinates)
Point source at 34.91 39.85 (WMAP bins wrt optical axis)
Point source at 11.24 48.78 (... in polar coordinates)
Total counts in region = 7.98000E+02
Weighted mean angle from optical axis = 11.449 arcmin
-> Standard Output From STOOL group_event_files:1 ad24043000g200170h.evt 13464 1 ad24043000g200270m.evt 13464 1 ad24043000g200370l.evt 13464 1 ad24043000g200470h.evt 13464-> GIS2_REGION256.4 already present in current directory
ad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 411 7314 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 281 5103 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 14 335 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 707 12757 0 0 0
in 37917.63 seconds
Spectrum has 707 counts for 1.8646E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.80969E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_1.pi group=yes
Wrote spectrum to ad24043000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad24043000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37918. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.80969E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 57 are grouped by a factor 58 ... 58 - 82 are grouped by a factor 25 ... 83 - 99 are grouped by a factor 17 ... 100 - 129 are grouped by a factor 15 ... 130 - 140 are grouped by a factor 11 ... 141 - 160 are grouped by a factor 20 ... 161 - 177 are grouped by a factor 17 ... 178 - 201 are grouped by a factor 24 ... 202 - 228 are grouped by a factor 27 ... 229 - 269 are grouped by a factor 41 ... 270 - 321 are grouped by a factor 52 ... 322 - 378 are grouped by a factor 57 ... 379 - 429 are grouped by a factor 51 ... 430 - 528 are grouped by a factor 99 ... 529 - 676 are grouped by a factor 148 ... 677 - 966 are grouped by a factor 290 ... 967 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 47 by 36 bins
expanded to 128 by 64 bins
First WMAP bin is at detector pixel 108 153
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 71.527 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 170.00 183.50 (detector coordinates)
Point source at -37.00 -52.54 (WMAP bins wrt optical axis)
Point source at 15.78 234.85 (... in polar coordinates)
Total counts in region = 7.07000E+02
Weighted mean angle from optical axis = 16.131 arcmin
-> Extracting ad24043000g210170_2.pi from ad24043000g225670_2.reg and:ad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 601 7124 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 418 4966 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 27 322 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 1046 12418 0 0 0
in 37917.63 seconds
Spectrum has 1046 counts for 2.7586E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.02692E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_2.pi group=yes
Wrote spectrum to ad24043000g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad24043000g210170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37918. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.02692E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 70 are grouped by a factor 71 ... 71 - 88 are grouped by a factor 18 ... 89 - 101 are grouped by a factor 13 ... 102 - 112 are grouped by a factor 11 ... 113 - 121 are grouped by a factor 9 ... 122 - 131 are grouped by a factor 10 ... 132 - 147 are grouped by a factor 8 ... 148 - 167 are grouped by a factor 10 ... 168 - 176 are grouped by a factor 9 ... 177 - 186 are grouped by a factor 10 ... 187 - 198 are grouped by a factor 12 ... 199 - 217 are grouped by a factor 19 ... 218 - 232 are grouped by a factor 15 ... 233 - 257 are grouped by a factor 25 ... 258 - 278 are grouped by a factor 21 ... 279 - 307 are grouped by a factor 29 ... 308 - 335 are grouped by a factor 28 ... 336 - 361 are grouped by a factor 26 ... 362 - 398 are grouped by a factor 37 ... 399 - 463 are grouped by a factor 65 ... 464 - 549 are grouped by a factor 86 ... 550 - 641 are grouped by a factor 92 ... 642 - 877 are grouped by a factor 236 ... 878 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g210170_2.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 29 by 29 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 107 102
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 40.588 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 137.00 132.00 (detector coordinates)
Point source at -4.00 -1.04 (WMAP bins wrt optical axis)
Point source at 1.01 194.57 (... in polar coordinates)
Total counts in region = 1.04600E+03
Weighted mean angle from optical axis = 2.102 arcmin
-> Extracting ad24043000g210170_3.pi from ad24043000g225670_3.reg and:ad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 390 7335 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 297 5087 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 18 331 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 706 12758 0 0 0
in 37917.63 seconds
Spectrum has 706 counts for 1.8619E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 9.04846E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_3.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_3.pi group=yes
Wrote spectrum to ad24043000g210170_3.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad24043000g210170_3.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g210170_3.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37918. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 9.04846E-03 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 69 are grouped by a factor 70 ... 70 - 83 are grouped by a factor 14 ... 84 - 93 are grouped by a factor 10 ... 94 - 115 are grouped by a factor 11 ... 116 - 124 are grouped by a factor 9 ... 125 - 146 are grouped by a factor 11 ... 147 - 160 are grouped by a factor 14 ... 161 - 173 are grouped by a factor 13 ... 174 - 193 are grouped by a factor 20 ... 194 - 228 are grouped by a factor 35 ... 229 - 271 are grouped by a factor 43 ... 272 - 318 are grouped by a factor 47 ... 319 - 401 are grouped by a factor 83 ... 402 - 523 are grouped by a factor 122 ... 524 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g210170_3.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 27 by 27 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 86 78
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 35.764 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 116.00 108.00 (detector coordinates)
Point source at 17.00 22.96 (WMAP bins wrt optical axis)
Point source at 7.02 53.48 (... in polar coordinates)
Total counts in region = 7.06000E+02
Weighted mean angle from optical axis = 7.058 arcmin
-> Extracting ad24043000g210170_4.pi from ad24043000g225670_4.reg and:ad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 446 7279 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 328 5056 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 26 323 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 800 12664 0 0 0
in 37917.63 seconds
Spectrum has 800 counts for 2.1098E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.07977E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_4.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_4.pi group=yes
Wrote spectrum to ad24043000g210170_4.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad24043000g210170_4.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g210170_4.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37918. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.07977E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 33 are grouped by a factor 34 ... 34 - 58 are grouped by a factor 25 ... 59 - 76 are grouped by a factor 18 ... 77 - 87 are grouped by a factor 11 ... 88 - 105 are grouped by a factor 9 ... 106 - 122 are grouped by a factor 17 ... 123 - 138 are grouped by a factor 16 ... 139 - 153 are grouped by a factor 15 ... 154 - 170 are grouped by a factor 17 ... 171 - 198 are grouped by a factor 28 ... 199 - 236 are grouped by a factor 38 ... 237 - 276 are grouped by a factor 40 ... 277 - 314 are grouped by a factor 38 ... 315 - 376 are grouped by a factor 62 ... 377 - 454 are grouped by a factor 78 ... 455 - 567 are grouped by a factor 113 ... 568 - 701 are grouped by a factor 134 ... 702 - 889 are grouped by a factor 188 ... 890 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g210170_4.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 35 by 49 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 28 81
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 82.202 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.00000E+02
Weighted mean angle from optical axis = 19.230 arcmin
-> Extracting ad24043000g210170_5.pi from ad24043000g225670_5.reg and:ad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 168 7557 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 123 5261 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 7 342 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 298 13166 0 0 0
in 37917.63 seconds
Spectrum has 298 counts for 7.8591E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.96619E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_5.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_5.pi group=yes
Wrote spectrum to ad24043000g210170_5.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g210170_5.pi since it has 298 eventsad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 157 7568 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 116 5268 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 0 349 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 273 13191 0 0 0
in 37917.63 seconds
Spectrum has 273 counts for 7.1998E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.47083E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_6.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_6.pi group=yes
Wrote spectrum to ad24043000g210170_6.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g210170_6.pi since it has 273 eventsad24043000g200170h.evt ad24043000g200270m.evt ad24043000g200370l.evt ad24043000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 150 7575 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 108 5276 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 11 338 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 270 13194 0 0 0
in 37917.63 seconds
Spectrum has 270 counts for 7.1207E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37918. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.44739E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g210170_7.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g210170_7.pi group=yes
Wrote spectrum to ad24043000g210170_7.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g210170_7.pi since it has 270 events1 ad24043000g300170h.evt 16417 1 ad24043000g300270m.evt 16417 1 ad24043000g300370l.evt 16417 1 ad24043000g300470h.evt 16417-> GIS3_REGION256.4 already present in current directory
ad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 1148 8250 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 821 5822 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 9 364 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 1979 14438 0 0 0
in 37829.63 seconds
Spectrum has 1979 counts for 5.2313E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.40991E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_1.pi group=yes
Wrote spectrum to ad24043000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad24043000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37830. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.40991E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 27 are grouped by a factor 28 ... 28 - 41 are grouped by a factor 14 ... 42 - 57 are grouped by a factor 16 ... 58 - 70 are grouped by a factor 13 ... 71 - 76 are grouped by a factor 6 ... 77 - 86 are grouped by a factor 5 ... 87 - 92 are grouped by a factor 6 ... 93 - 95 are grouped by a factor 3 ... 96 - 100 are grouped by a factor 5 ... 101 - 103 are grouped by a factor 3 ... 104 - 113 are grouped by a factor 5 ... 114 - 117 are grouped by a factor 4 ... 118 - 122 are grouped by a factor 5 ... 123 - 130 are grouped by a factor 4 ... 131 - 135 are grouped by a factor 5 ... 136 - 143 are grouped by a factor 4 ... 144 - 148 are grouped by a factor 5 ... 149 - 154 are grouped by a factor 6 ... 155 - 159 are grouped by a factor 5 ... 160 - 163 are grouped by a factor 4 ... 164 - 173 are grouped by a factor 5 ... 174 - 180 are grouped by a factor 7 ... 181 - 188 are grouped by a factor 8 ... 189 - 198 are grouped by a factor 10 ... 199 - 205 are grouped by a factor 7 ... 206 - 215 are grouped by a factor 10 ... 216 - 239 are grouped by a factor 12 ... 240 - 254 are grouped by a factor 15 ... 255 - 270 are grouped by a factor 16 ... 271 - 285 are grouped by a factor 15 ... 286 - 304 are grouped by a factor 19 ... 305 - 324 are grouped by a factor 20 ... 325 - 350 are grouped by a factor 26 ... 351 - 408 are grouped by a factor 29 ... 409 - 438 are grouped by a factor 30 ... 439 - 472 are grouped by a factor 34 ... 473 - 522 are grouped by a factor 50 ... 523 - 566 are grouped by a factor 44 ... 567 - 653 are grouped by a factor 87 ... 654 - 828 are grouped by a factor 175 ... 829 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 35 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 144 165
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 55.726 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 174.00 195.00 (detector coordinates)
Point source at -54.64 -60.56 (WMAP bins wrt optical axis)
Point source at 20.03 227.94 (... in polar coordinates)
Total counts in region = 1.97900E+03
Weighted mean angle from optical axis = 20.608 arcmin
-> Extracting ad24043000g310170_2.pi from ad24043000g325670_2.reg and:ad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 502 8896 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 380 6263 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 899 15518 0 0 0
in 37829.63 seconds
Spectrum has 899 counts for 2.3764E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.02692E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_2.pi group=yes
Wrote spectrum to ad24043000g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad24043000g310170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37830. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.02692E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 68 are grouped by a factor 69 ... 69 - 89 are grouped by a factor 21 ... 90 - 101 are grouped by a factor 12 ... 102 - 114 are grouped by a factor 13 ... 115 - 124 are grouped by a factor 10 ... 125 - 135 are grouped by a factor 11 ... 136 - 148 are grouped by a factor 13 ... 149 - 154 are grouped by a factor 6 ... 155 - 165 are grouped by a factor 11 ... 166 - 175 are grouped by a factor 10 ... 176 - 186 are grouped by a factor 11 ... 187 - 204 are grouped by a factor 18 ... 205 - 224 are grouped by a factor 20 ... 225 - 247 are grouped by a factor 23 ... 248 - 273 are grouped by a factor 26 ... 274 - 304 are grouped by a factor 31 ... 305 - 342 are grouped by a factor 38 ... 343 - 388 are grouped by a factor 46 ... 389 - 443 are grouped by a factor 55 ... 444 - 527 are grouped by a factor 84 ... 528 - 679 are grouped by a factor 152 ... 680 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g310170_2.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 29 by 29 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 113 103
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 40.588 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 143.00 133.00 (detector coordinates)
Point source at -23.64 1.44 (WMAP bins wrt optical axis)
Point source at 5.82 176.51 (... in polar coordinates)
Total counts in region = 8.99000E+02
Weighted mean angle from optical axis = 5.848 arcmin
-> Extracting ad24043000g310170_3.pi from ad24043000g325670_3.reg and:ad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 476 8922 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 318 6325 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 10 363 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 804 15613 0 0 0
in 37829.63 seconds
Spectrum has 804 counts for 2.1253E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 9.04846E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_3.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_3.pi group=yes
Wrote spectrum to ad24043000g310170_3.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad24043000g310170_3.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g310170_3.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37830. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 9.04846E-03 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 66 are grouped by a factor 67 ... 67 - 84 are grouped by a factor 18 ... 85 - 93 are grouped by a factor 9 ... 94 - 104 are grouped by a factor 11 ... 105 - 114 are grouped by a factor 10 ... 115 - 122 are grouped by a factor 8 ... 123 - 131 are grouped by a factor 9 ... 132 - 141 are grouped by a factor 10 ... 142 - 150 are grouped by a factor 9 ... 151 - 163 are grouped by a factor 13 ... 164 - 174 are grouped by a factor 11 ... 175 - 193 are grouped by a factor 19 ... 194 - 219 are grouped by a factor 26 ... 220 - 260 are grouped by a factor 41 ... 261 - 308 are grouped by a factor 48 ... 309 - 434 are grouped by a factor 63 ... 435 - 572 are grouped by a factor 138 ... 573 - 905 are grouped by a factor 333 ... 906 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g310170_3.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 27 by 27 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 93 78
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 35.764 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 123.00 108.00 (detector coordinates)
Point source at -3.64 26.44 (WMAP bins wrt optical axis)
Point source at 6.55 97.84 (... in polar coordinates)
Total counts in region = 8.04000E+02
Weighted mean angle from optical axis = 6.579 arcmin
-> Extracting ad24043000g310170_4.pi from ad24043000g325670_4.reg and:ad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 584 8814 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 376 6267 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 23 350 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 984 15433 0 0 0
in 37829.63 seconds
Spectrum has 984 counts for 2.6011E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.55334E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_4.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_4.pi group=yes
Wrote spectrum to ad24043000g310170_4.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad24043000g310170_4.pi for dead time... read all the files from deadlist.tmp-> Grouping ad24043000g310170_4.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37830. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.55334E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 26 are grouped by a factor 27 ... 27 - 37 are grouped by a factor 11 ... 38 - 53 are grouped by a factor 16 ... 54 - 68 are grouped by a factor 15 ... 69 - 79 are grouped by a factor 11 ... 80 - 88 are grouped by a factor 9 ... 89 - 96 are grouped by a factor 8 ... 97 - 105 are grouped by a factor 9 ... 106 - 113 are grouped by a factor 8 ... 114 - 146 are grouped by a factor 11 ... 147 - 159 are grouped by a factor 13 ... 160 - 176 are grouped by a factor 17 ... 177 - 191 are grouped by a factor 15 ... 192 - 216 are grouped by a factor 25 ... 217 - 250 are grouped by a factor 34 ... 251 - 305 are grouped by a factor 55 ... 306 - 354 are grouped by a factor 49 ... 355 - 419 are grouped by a factor 65 ... 420 - 515 are grouped by a factor 96 ... 516 - 639 are grouped by a factor 124 ... 640 - 896 are grouped by a factor 257 ... 897 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad24043000g310170_4.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 28 by 48 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 24 81
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 61.395 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.84000E+02
Weighted mean angle from optical axis = 16.690 arcmin
-> Extracting ad24043000g310170_5.pi from ad24043000g325670_5.reg and:ad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 252 9146 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 218 6425 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 487 15930 0 0 0
in 37829.63 seconds
Spectrum has 487 counts for 1.2874E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 7.75146E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_5.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_5.pi group=yes
Wrote spectrum to ad24043000g310170_5.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g310170_5.pi since it has 487 eventsad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 217 9181 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 151 6492 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 6 367 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 374 16043 0 0 0
in 37829.63 seconds
Spectrum has 374 counts for 9.8864E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.47083E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_6.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_6.pi group=yes
Wrote spectrum to ad24043000g310170_6.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g310170_6.pi since it has 374 eventsad24043000g300170h.evt ad24043000g300270m.evt ad24043000g300370l.evt ad24043000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 208 9190 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 126 6517 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 11 362 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 345 16072 0 0 0
in 37829.63 seconds
Spectrum has 345 counts for 9.1198E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37830. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.44739E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g310170_7.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g310170_7.pi group=yes
Wrote spectrum to ad24043000g310170_7.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g310170_7.pi since it has 345 events
XSPEC 9.01 01:44:05 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g210170_1.pi
Net count rate (cts/s) for file 1 1.8646E-02+/- 7.2562E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g210170_2_pi.ps from ad24043000g210170_2.pi
XSPEC 9.01 01:44:35 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g210170_2.pi
Net count rate (cts/s) for file 1 2.7586E-02+/- 9.0709E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g210170_3_pi.ps from ad24043000g210170_3.pi
XSPEC 9.01 01:45:03 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g210170_3.pi
Net count rate (cts/s) for file 1 1.8619E-02+/- 9.0209E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g210170_4_pi.ps from ad24043000g210170_4.pi
XSPEC 9.01 01:45:33 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g210170_4.pi
Net count rate (cts/s) for file 1 2.1098E-02+/- 7.9950E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g310170_1_pi.ps from ad24043000g310170_1.pi
XSPEC 9.01 01:46:02 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g310170_1.pi
Net count rate (cts/s) for file 1 5.2313E-02+/- 1.2251E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g310170_2_pi.ps from ad24043000g310170_2.pi
XSPEC 9.01 01:46:32 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g310170_2.pi
Net count rate (cts/s) for file 1 2.3764E-02+/- 9.1914E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g310170_3_pi.ps from ad24043000g310170_3.pi
XSPEC 9.01 01:47:02 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g310170_3.pi
Net count rate (cts/s) for file 1 2.1253E-02+/- 7.9786E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000g310170_4_pi.ps from ad24043000g310170_4.pi
XSPEC 9.01 01:47:32 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000g310170_4.pi
Net count rate (cts/s) for file 1 2.6011E-02+/- 8.7433E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s010102_1_pi.ps from ad24043000s010102_1.pi
XSPEC 9.01 01:48:00 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s010102_1.pi
Net count rate (cts/s) for file 1 3.7569E-02+/- 1.0371E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s010102_2_pi.ps from ad24043000s010102_2.pi
XSPEC 9.01 01:48:33 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s010102_2.pi
Net count rate (cts/s) for file 1 2.0925E-02+/- 7.7805E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s010212_1_pi.ps from ad24043000s010212_1.pi
XSPEC 9.01 01:49:04 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s010212_1.pi
Net count rate (cts/s) for file 1 3.8731E-02+/- 1.0590E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s010212_2_pi.ps from ad24043000s010212_2.pi
XSPEC 9.01 01:49:39 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s010212_2.pi
Net count rate (cts/s) for file 1 2.2314E-02+/- 8.0945E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s110102_1_pi.ps from ad24043000s110102_1.pi
XSPEC 9.01 01:50:14 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s110102_1.pi
Net count rate (cts/s) for file 1 3.1319E-02+/- 9.2751E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s110102_2_pi.ps from ad24043000s110102_2.pi
XSPEC 9.01 01:50:46 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s110102_2.pi
Net count rate (cts/s) for file 1 2.1304E-02+/- 7.6714E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s110212_1_pi.ps from ad24043000s110212_1.pi
XSPEC 9.01 01:51:16 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s110212_1.pi
Net count rate (cts/s) for file 1 3.2323E-02+/- 9.4794E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad24043000s110212_2_pi.ps from ad24043000s110212_2.pi
XSPEC 9.01 01:51:52 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad24043000s110212_2.pi
Net count rate (cts/s) for file 1 2.2254E-02+/- 7.9124E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 735 991 0 0 0
Writing events file
735 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 476 726 0 0 0
Writing events file
1211 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 117 140 0 0 0
Writing events file
1328 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3185 1328 1857 0 0 0
in 35268.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad24043000s000002_1.lc with binsize 1327.88296115125
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.35E+05 1328 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
1328 1328 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1328 1328 0 0 0 0
in 35268.57 seconds
Fits light curve has 1328 counts for 3.7654E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > set binsize 1327.88296115125
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad24043000s000002_1.lc
Wrote FITS light curve to file ad24043000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad24043000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 06:32:43.003
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:48.485
No. of Rows ....... 26 Bin Time (s) ...... 1328.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 61 Newbins of 1327.88 (s)
Intv 1 Start10143 6:43:46
Ser.1 Avg 0.3823E-01 Chisq 39.17 Var 0.5377E-04 Newbs. 26
Min 0.2661E-01 Max 0.5933E-01expVar 0.3569E-04 Bins 26
Results from Statistical Analysis
Newbin Integration Time (s).. 1327.9
Interval Duration (s)........ 75689.
No. of Newbins .............. 26
Average (c/s) ............... 0.38231E-01 +/- 0.12E-02
Standard Deviation (c/s)..... 0.73329E-02
Minimum (c/s)................ 0.26607E-01
Maximum (c/s)................ 0.59331E-01
Variance ((c/s)**2).......... 0.53772E-04 +/- 0.15E-04
Expected Variance ((c/s)**2). 0.35694E-04 +/- 0.10E-04
Third Moment ((c/s)**3)...... 0.37712E-06
Average Deviation (c/s)...... 0.60436E-02
Skewness..................... 0.95642 +/- 0.48
Kurtosis..................... 0.64211 +/- 0.96
RMS fractional variation....< 0.11667 (3 sigma)
Chi-Square................... 39.168 dof 25
Chi-Square Prob of constancy. 0.35445E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.20185E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 61 Newbins of 1327.88 (s)
Intv 1 Start10143 6:43:46
Ser.1 Avg 0.3823E-01 Chisq 39.17 Var 0.5377E-04 Newbs. 26
Min 0.2661E-01 Max 0.5933E-01expVar 0.3569E-04 Bins 26
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000s032002_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 398 1328 0 0 0
Writing events file
398 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 305 897 0 0 0
Writing events file
703 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 44 213 0 0 0
Writing events file
747 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3185 747 2438 0 0 0
in 35268.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > read events ad24043000s000402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad24043000s000002_2.lc with binsize 2360.68081982444
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.35E+05 747 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
747 747 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
747 747 0 0 0 0
in 35268.57 seconds
Fits light curve has 747 counts for 2.1180E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > set binsize 2360.68081982444
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad24043000s000002_2.lc
Wrote FITS light curve to file ad24043000s000002_2.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad24043000s000002_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000s000002_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 06:32:43.003
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:48.485
No. of Rows ....... 15 Bin Time (s) ...... 2361.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 35 Newbins of 2360.68 (s)
Intv 1 Start10143 6:52:23
Ser.1 Avg 0.2056E-01 Chisq 62.01 Var 0.5059E-04 Newbs. 15
Min 0.1040E-01 Max 0.3809E-01expVar 0.1224E-04 Bins 15
Results from Statistical Analysis
Newbin Integration Time (s).. 2360.7
Interval Duration (s)........ 75542.
No. of Newbins .............. 15
Average (c/s) ............... 0.20560E-01 +/- 0.93E-03
Standard Deviation (c/s)..... 0.71125E-02
Minimum (c/s)................ 0.10400E-01
Maximum (c/s)................ 0.38090E-01
Variance ((c/s)**2).......... 0.50587E-04 +/- 0.19E-04
Expected Variance ((c/s)**2). 0.12237E-04 +/- 0.46E-05
Third Moment ((c/s)**3)...... 0.30133E-06
Average Deviation (c/s)...... 0.57397E-02
Skewness..................... 0.83751 +/- 0.63
Kurtosis..................... 0.18117 +/- 1.3
RMS fractional variation..... 0.30120 +/- 0.75E-01
Chi-Square................... 62.007 dof 14
Chi-Square Prob of constancy. 0.52011E-07 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.20321E-04 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 35 Newbins of 2360.68 (s)
Intv 1 Start10143 6:52:23
Ser.1 Avg 0.2056E-01 Chisq 62.01 Var 0.5059E-04 Newbs. 15
Min 0.1040E-01 Max 0.3809E-01expVar 0.1224E-04 Bins 15
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad24043000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
4 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 605 1010 0 0 0
Writing events file
605 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 382 652 0 0 0
Writing events file
987 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 129 152 0 0 0
Writing events file
1116 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 38 75 0 0 0
Writing events file
1154 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3043 1154 1889 0 0 0
in 36846.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad24043000s100002_1.lc with binsize 1596.48637641383
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.37E+05 1154 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
1154 1154 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1154 1154 0 0 0 0
in 36846.91 seconds
Fits light curve has 1154 counts for 3.1319E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > set binsize 1596.48637641383
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad24043000s100002_1.lc
Wrote FITS light curve to file ad24043000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad24043000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:46:19.003
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:48.485
No. of Rows ....... 25 Bin Time (s) ...... 1596.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 53 Newbins of 1596.49 (s)
Intv 1 Start10143 6:52:50
Ser.1 Avg 0.3158E-01 Chisq 26.81 Var 0.2923E-04 Newbs. 25
Min 0.2328E-01 Max 0.4445E-01expVar 0.2726E-04 Bins 25
Results from Statistical Analysis
Newbin Integration Time (s).. 1596.5
Interval Duration (s)........ 75035.
No. of Newbins .............. 25
Average (c/s) ............... 0.31583E-01 +/- 0.11E-02
Standard Deviation (c/s)..... 0.54064E-02
Minimum (c/s)................ 0.23282E-01
Maximum (c/s)................ 0.44450E-01
Variance ((c/s)**2).......... 0.29229E-04 +/- 0.84E-05
Expected Variance ((c/s)**2). 0.27260E-04 +/- 0.79E-05
Third Moment ((c/s)**3)...... 0.70694E-07
Average Deviation (c/s)...... 0.45886E-02
Skewness..................... 0.44735 +/- 0.49
Kurtosis.....................-0.39788 +/- 0.98
RMS fractional variation....< 0.16683 (3 sigma)
Chi-Square................... 26.806 dof 24
Chi-Square Prob of constancy. 0.31364 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.43602E-03 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 53 Newbins of 1596.49 (s)
Intv 1 Start10143 6:52:50
Ser.1 Avg 0.3158E-01 Chisq 26.81 Var 0.2923E-04 Newbs. 25
Min 0.2328E-01 Max 0.4445E-01expVar 0.2726E-04 Bins 25
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000s132002_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
2 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
3 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
4 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 423 1192 0 0 0
Writing events file
423 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 312 722 0 0 0
Writing events file
735 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 46 235 0 0 0
Writing events file
781 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 18 95 0 0 0
Writing events file
799 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3043 799 2244 0 0 0
in 36846.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100402h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > read events ad24043000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad24043000s100002_2.lc with binsize 2305.81386530858
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.37E+05 799 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
799 799 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
799 799 0 0 0 0
in 36846.91 seconds
Fits light curve has 799 counts for 2.1684E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > set binsize 2305.81386530858
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad24043000s100002_2.lc
Wrote FITS light curve to file ad24043000s100002_2.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad24043000s100002_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000s100002_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:46:19.003
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:48.485
No. of Rows ....... 17 Bin Time (s) ...... 2306.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 37 Newbins of 2305.81 (s)
Intv 1 Start10143 6:43:57
Ser.1 Avg 0.2209E-01 Chisq 128.3 Var 0.1077E-03 Newbs. 17
Min 0.1221E-01 Max 0.5803E-01expVar 0.1427E-04 Bins 17
Results from Statistical Analysis
Newbin Integration Time (s).. 2305.8
Interval Duration (s)........ 76092.
No. of Newbins .............. 17
Average (c/s) ............... 0.22089E-01 +/- 0.94E-03
Standard Deviation (c/s)..... 0.10378E-01
Minimum (c/s)................ 0.12214E-01
Maximum (c/s)................ 0.58028E-01
Variance ((c/s)**2).......... 0.10769E-03 +/- 0.38E-04
Expected Variance ((c/s)**2). 0.14272E-04 +/- 0.50E-05
Third Moment ((c/s)**3)...... 0.26565E-05
Average Deviation (c/s)...... 0.66036E-02
Skewness..................... 2.3770 +/- 0.59
Kurtosis..................... 5.6655 +/- 1.2
RMS fractional variation..... 0.43757 +/- 0.89E-01
Chi-Square................... 128.28 dof 16
Chi-Square Prob of constancy. 0.13854E-18 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.11224E-06 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 37 Newbins of 2305.81 (s)
Intv 1 Start10143 6:43:57
Ser.1 Avg 0.2209E-01 Chisq 128.3 Var 0.1077E-03 Newbs. 17
Min 0.1221E-01 Max 0.5803E-01expVar 0.1427E-04 Bins 17
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad24043000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 411 7314 0 0 0
Writing events file
411 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 281 5103 0 0 0
Writing events file
692 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
693 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 14 335 0 0 0
Writing events file
707 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 707 12757 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200070_1.lc with binsize 2681.58595705618
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 707 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
707 707 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
707 707 0 0 0 0
in 37917.63 seconds
Fits light curve has 707 counts for 1.8646E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set binsize 2681.58595705618
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad24043000g200070_1.lc
Wrote FITS light curve to file ad24043000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad24043000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 12 Bin Time (s) ...... 2682.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 32 Newbins of 2681.59 (s)
Intv 1 Start10143 6:48:27
Ser.1 Avg 0.1756E-01 Chisq 42.89 Var 0.3445E-04 Newbs. 12
Min 0.1327E-01 Max 0.3172E-01expVar 0.9638E-05 Bins 12
Results from Statistical Analysis
Newbin Integration Time (s).. 2681.6
Interval Duration (s)........ 75084.
No. of Newbins .............. 12
Average (c/s) ............... 0.17564E-01 +/- 0.94E-03
Standard Deviation (c/s)..... 0.58692E-02
Minimum (c/s)................ 0.13265E-01
Maximum (c/s)................ 0.31717E-01
Variance ((c/s)**2).......... 0.34447E-04 +/- 0.15E-04
Expected Variance ((c/s)**2). 0.96380E-05 +/- 0.41E-05
Third Moment ((c/s)**3)...... 0.29556E-06
Average Deviation (c/s)...... 0.45769E-02
Skewness..................... 1.4619 +/- 0.71
Kurtosis..................... 0.68475 +/- 1.4
RMS fractional variation..... 0.28359 +/- 0.84E-01
Chi-Square................... 42.889 dof 11
Chi-Square Prob of constancy. 0.11355E-04 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.25073E-07 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 32 Newbins of 2681.59 (s)
Intv 1 Start10143 6:48:27
Ser.1 Avg 0.1756E-01 Chisq 42.89 Var 0.3445E-04 Newbs. 12
Min 0.1327E-01 Max 0.3172E-01expVar 0.9638E-05 Bins 12
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g225670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 601 7124 0 0 0
Writing events file
601 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 418 4966 0 0 0
Writing events file
1019 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
1019 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 27 322 0 0 0
Writing events file
1046 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 1046 12418 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200070_2.lc with binsize 1812.50599583052
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 1046 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
1046 1046 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1046 1046 0 0 0 0
in 37917.63 seconds
Fits light curve has 1046 counts for 2.7586E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set binsize 1812.50599583052
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad24043000g200070_2.lc
Wrote FITS light curve to file ad24043000g200070_2.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad24043000g200070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 19 Bin Time (s) ...... 1813.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 47 Newbins of 1812.51 (s)
Intv 1 Start10143 6:56:56
Ser.1 Avg 0.2831E-01 Chisq 78.99 Var 0.8888E-04 Newbs. 19
Min 0.1631E-01 Max 0.6313E-01expVar 0.2138E-04 Bins 19
Results from Statistical Analysis
Newbin Integration Time (s).. 1812.5
Interval Duration (s)........ 74313.
No. of Newbins .............. 19
Average (c/s) ............... 0.28309E-01 +/- 0.11E-02
Standard Deviation (c/s)..... 0.94278E-02
Minimum (c/s)................ 0.16306E-01
Maximum (c/s)................ 0.63131E-01
Variance ((c/s)**2).......... 0.88884E-04 +/- 0.30E-04
Expected Variance ((c/s)**2). 0.21380E-04 +/- 0.71E-05
Third Moment ((c/s)**3)...... 0.21021E-05
Average Deviation (c/s)...... 0.59717E-02
Skewness..................... 2.5085 +/- 0.56
Kurtosis..................... 7.0064 +/- 1.1
RMS fractional variation..... 0.29022 +/- 0.64E-01
Chi-Square................... 78.990 dof 18
Chi-Square Prob of constancy. 0.12869E-08 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.21916E-07 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 47 Newbins of 1812.51 (s)
Intv 1 Start10143 6:56:56
Ser.1 Avg 0.2831E-01 Chisq 78.99 Var 0.8888E-04 Newbs. 19
Min 0.1631E-01 Max 0.6313E-01expVar 0.2138E-04 Bins 19
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g225670_3.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 390 7335 0 0 0
Writing events file
390 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 297 5087 0 0 0
Writing events file
687 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
688 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 18 331 0 0 0
Writing events file
706 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 706 12758 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200070_3.lc with binsize 2685.38423744861
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 706 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
706 706 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
706 706 0 0 0 0
in 37917.63 seconds
Fits light curve has 706 counts for 1.8619E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set binsize 2685.38423744861
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad24043000g200070_3.lc
Wrote FITS light curve to file ad24043000g200070_3.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad24043000g200070_3_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g200070_3.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 13 Bin Time (s) ...... 2685.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 32 Newbins of 2685.38 (s)
Intv 1 Start10143 6:48:33
Ser.1 Avg 0.1825E-01 Chisq 13.95 Var 0.1108E-04 Newbs. 13
Min 0.1100E-01 Max 0.2250E-01expVar 0.1032E-04 Bins 13
Results from Statistical Analysis
Newbin Integration Time (s).. 2685.4
Interval Duration (s)........ 75191.
No. of Newbins .............. 13
Average (c/s) ............... 0.18249E-01 +/- 0.93E-03
Standard Deviation (c/s)..... 0.33284E-02
Minimum (c/s)................ 0.10998E-01
Maximum (c/s)................ 0.22500E-01
Variance ((c/s)**2).......... 0.11078E-04 +/- 0.45E-05
Expected Variance ((c/s)**2). 0.10322E-04 +/- 0.42E-05
Third Moment ((c/s)**3)......-0.16290E-07
Average Deviation (c/s)...... 0.28484E-02
Skewness.....................-0.44180 +/- 0.68
Kurtosis.....................-0.54220 +/- 1.4
RMS fractional variation....< 0.22267 (3 sigma)
Chi-Square................... 13.952 dof 12
Chi-Square Prob of constancy. 0.30370 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.66077E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 32 Newbins of 2685.38 (s)
Intv 1 Start10143 6:48:33
Ser.1 Avg 0.1825E-01 Chisq 13.95 Var 0.1108E-04 Newbs. 13
Min 0.1100E-01 Max 0.2250E-01expVar 0.1032E-04 Bins 13
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g225670_4.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 446 7279 0 0 0
Writing events file
446 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 328 5056 0 0 0
Writing events file
774 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
774 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 26 323 0 0 0
Writing events file
800 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 800 12664 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200070_4.lc with binsize 2369.8515895484
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 800 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
800 800 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
800 800 0 0 0 0
in 37917.63 seconds
Fits light curve has 800 counts for 2.1098E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > set binsize 2369.8515895484
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad24043000g200070_4.lc
Wrote FITS light curve to file ad24043000g200070_4.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad24043000g200070_4_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g200070_4.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 15 Bin Time (s) ...... 2370.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 36 Newbins of 2369.85 (s)
Intv 1 Start10143 6:40:39
Ser.1 Avg 0.2145E-01 Chisq 18.22 Var 0.1603E-04 Newbs. 15
Min 0.1398E-01 Max 0.2624E-01expVar 0.1319E-04 Bins 15
Results from Statistical Analysis
Newbin Integration Time (s).. 2369.9
Interval Duration (s)........ 75835.
No. of Newbins .............. 15
Average (c/s) ............... 0.21449E-01 +/- 0.97E-03
Standard Deviation (c/s)..... 0.40034E-02
Minimum (c/s)................ 0.13984E-01
Maximum (c/s)................ 0.26235E-01
Variance ((c/s)**2).......... 0.16027E-04 +/- 0.61E-05
Expected Variance ((c/s)**2). 0.13192E-04 +/- 0.50E-05
Third Moment ((c/s)**3)......-0.24019E-07
Average Deviation (c/s)...... 0.36149E-02
Skewness.....................-0.37433 +/- 0.63
Kurtosis..................... -1.3038 +/- 1.3
RMS fractional variation....< 0.19314 (3 sigma)
Chi-Square................... 18.223 dof 14
Chi-Square Prob of constancy. 0.19683 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.51223E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 36 Newbins of 2369.85 (s)
Intv 1 Start10143 6:40:39
Ser.1 Avg 0.2145E-01 Chisq 18.22 Var 0.1603E-04 Newbs. 15
Min 0.1398E-01 Max 0.2624E-01expVar 0.1319E-04 Bins 15
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g225670_5.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 168 7557 0 0 0
Writing events file
168 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 123 5261 0 0 0
Writing events file
291 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
291 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 7 342 0 0 0
Writing events file
298 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 298 13166 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> skipping ad24043000g200070_5.lc since it would have 298 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 157 7568 0 0 0
Writing events file
157 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 116 5268 0 0 0
Writing events file
273 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
273 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 0 349 0 0 0
Writing events file
273 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 273 13191 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> skipping ad24043000g200070_6.lc since it would have 273 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 150 7575 0 0 0
Writing events file
150 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 108 5276 0 0 0
Writing events file
258 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
259 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 11 338 0 0 0
Writing events file
270 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13464 270 13194 0 0 0
in 37917.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> skipping ad24043000g200070_7.lc since it would have 270 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 1148 8250 0 0 0
Writing events file
1148 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 821 5822 0 0 0
Writing events file
1969 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Writing events file
1970 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 9 364 0 0 0
Writing events file
1979 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 1979 14438 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300070_1.lc with binsize 955.776295091104
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 1979 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
1979 1979 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1979 1979 0 0 0 0
in 37829.63 seconds
Fits light curve has 1979 counts for 5.2313E-02 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set binsize 955.776295091104
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad24043000g300070_1.lc
Wrote FITS light curve to file ad24043000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad24043000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 44 Bin Time (s) ...... 955.8
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 88 Newbins of 955.776 (s)
Intv 1 Start10143 6:37:10
Ser.1 Avg 0.5229E-01 Chisq 2133. Var 0.3440E-02 Newbs. 44
Min 0.7676E-02 Max 0.2632 expVar 0.7097E-04 Bins 44
Results from Statistical Analysis
Newbin Integration Time (s).. 955.78
Interval Duration (s)........ 80285.
No. of Newbins .............. 44
Average (c/s) ............... 0.52290E-01 +/- 0.13E-02
Standard Deviation (c/s)..... 0.58651E-01
Minimum (c/s)................ 0.76761E-02
Maximum (c/s)................ 0.26325
Variance ((c/s)**2).......... 0.34400E-02 +/- 0.74E-03
Expected Variance ((c/s)**2). 0.70974E-04 +/- 0.15E-04
Third Moment ((c/s)**3)...... 0.35398E-03
Average Deviation (c/s)...... 0.44557E-01
Skewness..................... 1.7545 +/- 0.37
Kurtosis..................... 2.6566 +/- 0.74
RMS fractional variation..... 1.1100 +/- 0.12
Chi-Square................... 2132.6 dof 43
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 88 Newbins of 955.776 (s)
Intv 1 Start10143 6:37:10
Ser.1 Avg 0.5229E-01 Chisq 2133. Var 0.3440E-02 Newbs. 44
Min 0.7676E-02 Max 0.2632 expVar 0.7097E-04 Bins 44
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> Extracting events from region ad24043000g325670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 502 8896 0 0 0
Writing events file
502 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 380 6263 0 0 0
Writing events file
882 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
882 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
Writing events file
899 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 899 15518 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300070_2.lc with binsize 2103.98363513381
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 899 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
899 899 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
899 899 0 0 0 0
in 37829.63 seconds
Fits light curve has 899 counts for 2.3764E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set binsize 2103.98363513381
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad24043000g300070_2.lc
Wrote FITS light curve to file ad24043000g300070_2.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad24043000g300070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 17 Bin Time (s) ...... 2104.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 40 Newbins of 2103.98 (s)
Intv 1 Start10143 6:34: 0
Ser.1 Avg 0.2451E-01 Chisq 50.22 Var 0.4801E-04 Newbs. 17
Min 0.1693E-01 Max 0.4717E-01expVar 0.1625E-04 Bins 17
Results from Statistical Analysis
Newbin Integration Time (s).. 2104.0
Interval Duration (s)........ 75743.
No. of Newbins .............. 17
Average (c/s) ............... 0.24507E-01 +/- 0.10E-02
Standard Deviation (c/s)..... 0.69287E-02
Minimum (c/s)................ 0.16935E-01
Maximum (c/s)................ 0.47170E-01
Variance ((c/s)**2).......... 0.48006E-04 +/- 0.17E-04
Expected Variance ((c/s)**2). 0.16251E-04 +/- 0.57E-05
Third Moment ((c/s)**3)...... 0.65250E-06
Average Deviation (c/s)...... 0.46424E-02
Skewness..................... 1.9617 +/- 0.59
Kurtosis..................... 4.0633 +/- 1.2
RMS fractional variation..... 0.22994 +/- 0.61E-01
Chi-Square................... 50.219 dof 16
Chi-Square Prob of constancy. 0.21160E-04 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.23729E-06 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 40 Newbins of 2103.98 (s)
Intv 1 Start10143 6:34: 0
Ser.1 Avg 0.2451E-01 Chisq 50.22 Var 0.4801E-04 Newbs. 17
Min 0.1693E-01 Max 0.4717E-01expVar 0.1625E-04 Bins 17
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g325670_3.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 476 8922 0 0 0
Writing events file
476 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 318 6325 0 0 0
Writing events file
794 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
794 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 10 363 0 0 0
Writing events file
804 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 804 15613 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300070_3.lc with binsize 2352.58866664838
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 804 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
804 804 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
804 804 0 0 0 0
in 37829.63 seconds
Fits light curve has 804 counts for 2.1253E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set binsize 2352.58866664838
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad24043000g300070_3.lc
Wrote FITS light curve to file ad24043000g300070_3.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad24043000g300070_3_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g300070_3.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 16 Bin Time (s) ...... 2353.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 36 Newbins of 2352.59 (s)
Intv 1 Start10143 6:40:13
Ser.1 Avg 0.2192E-01 Chisq 10.70 Var 0.8890E-05 Newbs. 16
Min 0.1562E-01 Max 0.2793E-01expVar 0.1330E-04 Bins 16
Results from Statistical Analysis
Newbin Integration Time (s).. 2352.6
Interval Duration (s)........ 75283.
No. of Newbins .............. 16
Average (c/s) ............... 0.21923E-01 +/- 0.94E-03
Standard Deviation (c/s)..... 0.29816E-02
Minimum (c/s)................ 0.15625E-01
Maximum (c/s)................ 0.27933E-01
Variance ((c/s)**2).......... 0.88899E-05 +/- 0.32E-05
Expected Variance ((c/s)**2). 0.13295E-04 +/- 0.49E-05
Third Moment ((c/s)**3)......-0.83704E-08
Average Deviation (c/s)...... 0.21611E-02
Skewness.....................-0.31579 +/- 0.61
Kurtosis..................... 0.25743 +/- 1.2
RMS fractional variation....< 0.22220 (3 sigma)
Chi-Square................... 10.698 dof 15
Chi-Square Prob of constancy. 0.77364 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.74438E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 36 Newbins of 2352.59 (s)
Intv 1 Start10143 6:40:13
Ser.1 Avg 0.2192E-01 Chisq 10.70 Var 0.8890E-05 Newbs. 16
Min 0.1562E-01 Max 0.2793E-01expVar 0.1330E-04 Bins 16
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g325670_4.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 584 8814 0 0 0
Writing events file
584 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 376 6267 0 0 0
Writing events file
960 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Writing events file
961 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 23 350 0 0 0
Writing events file
984 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 984 15433 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300070_4.lc with binsize 1922.23708128587
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.38E+05 984 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/events.tmp
Total Good Bad: Region Time Phase Cut
984 984 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
984 984 0 0 0 0
in 37829.63 seconds
Fits light curve has 984 counts for 2.6011E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > set binsize 1922.23708128587
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad24043000g300070_4.lc
Wrote FITS light curve to file ad24043000g300070_4.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad24043000g300070_4_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad24043000g300070_4.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_2023 Start Time (d) .... 10143 05:41:24.997
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10144 05:00:59.003
No. of Rows ....... 16 Bin Time (s) ...... 1922.
Right Ascension ... 8.5364E+01 Internal time sys.. Converted to TJD
Declination ....... -2.3244E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 44 Newbins of 1922.24 (s)
Intv 1 Start10143 7: 1:30
Ser.1 Avg 0.2635E-01 Chisq 9.158 Var 0.1024E-04 Newbs. 16
Min 0.1911E-01 Max 0.3209E-01expVar 0.1789E-04 Bins 16
Results from Statistical Analysis
Newbin Integration Time (s).. 1922.2
Interval Duration (s)........ 73045.
No. of Newbins .............. 16
Average (c/s) ............... 0.26348E-01 +/- 0.11E-02
Standard Deviation (c/s)..... 0.32003E-02
Minimum (c/s)................ 0.19109E-01
Maximum (c/s)................ 0.32090E-01
Variance ((c/s)**2).......... 0.10242E-04 +/- 0.37E-05
Expected Variance ((c/s)**2). 0.17893E-04 +/- 0.65E-05
Third Moment ((c/s)**3)......-0.14476E-07
Average Deviation (c/s)...... 0.23712E-02
Skewness.....................-0.44165 +/- 0.61
Kurtosis..................... 0.69698E-01 +/- 1.2
RMS fractional variation....< 0.22019 (3 sigma)
Chi-Square................... 9.1583 dof 15
Chi-Square Prob of constancy. 0.86907 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.66340 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 44 Newbins of 1922.24 (s)
Intv 1 Start10143 7: 1:30
Ser.1 Avg 0.2635E-01 Chisq 9.158 Var 0.1024E-04 Newbs. 16
Min 0.1911E-01 Max 0.3209E-01expVar 0.1789E-04 Bins 16
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad24043000g325670_5.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 252 9146 0 0 0
Writing events file
252 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 218 6425 0 0 0
Writing events file
470 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
470 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
Writing events file
487 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 487 15930 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> skipping ad24043000g300070_5.lc since it would have 487 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 217 9181 0 0 0
Writing events file
217 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 151 6492 0 0 0
Writing events file
368 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
368 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 6 367 0 0 0
Writing events file
374 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 374 16043 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> skipping ad24043000g300070_6.lc since it would have 374 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 208 9190 0 0 0
Writing events file
208 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 126 6517 0 0 0
Writing events file
334 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
334 events written to the output file
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 11 362 0 0 0
Writing events file
345 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16417 345 16072 0 0 0
in 37829.63 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> skipping ad24043000g300070_7.lc since it would have 345 eventsad24043000g200170h.evt[2] ad24043000g200270m.evt[2] ad24043000g200370l.evt[2] ad24043000g200470h.evt[2]-> Making L1 light curve of ft960301_0512_0500G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 46058 output records from 46169 good input G2_L1 records.-> Making L1 light curve of ft960301_0512_0500G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 34116 output records from 60106 good input G2_L1 records.-> Merging GTIs from the following files:
ad24043000g300170h.evt[2] ad24043000g300270m.evt[2] ad24043000g300370l.evt[2] ad24043000g300470h.evt[2]-> Making L1 light curve of ft960301_0512_0500G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 45316 output records from 45428 good input G3_L1 records.-> Making L1 light curve of ft960301_0512_0500G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 33857 output records from 59167 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 411 7314 0 0 0
Writing events file
411 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 411 7314 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_1.ulc use_events=yes
Wrote events list to file ad24043000g200170h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 601 7124 0 0 0
Writing events file
601 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 601 7124 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_2.ulc use_events=yes
Wrote events list to file ad24043000g200170h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 390 7335 0 0 0
Writing events file
390 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 390 7335 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_3.ulc use_events=yes
Wrote events list to file ad24043000g200170h_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 446 7279 0 0 0
Writing events file
446 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 446 7279 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_4.ulc use_events=yes
Wrote events list to file ad24043000g200170h_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 168 7557 0 0 0
Writing events file
168 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 168 7557 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_5.ulc use_events=yes
Wrote events list to file ad24043000g200170h_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_6.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 157 7568 0 0 0
Writing events file
157 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 157 7568 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_6.ulc use_events=yes
Wrote events list to file ad24043000g200170h_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200170h_7.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 7725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.evt
Total Good Bad: Region Time Phase Cut
7725 150 7575 0 0 0
Writing events file
150 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7725 150 7575 0 0 0
in 21532.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200170h_7.ulc use_events=yes
Wrote events list to file ad24043000g200170h_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 281 5103 0 0 0
Writing events file
281 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 281 5103 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_1.ulc use_events=yes
Wrote events list to file ad24043000g200270m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 418 4966 0 0 0
Writing events file
418 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 418 4966 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_2.ulc use_events=yes
Wrote events list to file ad24043000g200270m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 297 5087 0 0 0
Writing events file
297 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 297 5087 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_3.ulc use_events=yes
Wrote events list to file ad24043000g200270m_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 328 5056 0 0 0
Writing events file
328 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 328 5056 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_4.ulc use_events=yes
Wrote events list to file ad24043000g200270m_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 123 5261 0 0 0
Writing events file
123 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 123 5261 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_5.ulc use_events=yes
Wrote events list to file ad24043000g200270m_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_6.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 116 5268 0 0 0
Writing events file
116 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 116 5268 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_6.ulc use_events=yes
Wrote events list to file ad24043000g200270m_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200270m_7.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 5384 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.evt
Total Good Bad: Region Time Phase Cut
5384 108 5276 0 0 0
Writing events file
108 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5384 108 5276 0 0 0
in 15359.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200270m_7.ulc use_events=yes
Wrote events list to file ad24043000g200270m_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200370l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_1.ulc use_events=yes
Wrote events list to file ad24043000g200370l_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_1.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_2.ulc use_events=yes
Wrote events list to file ad24043000g200370l_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_2.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_3.ulc use_events=yes
Wrote events list to file ad24043000g200370l_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_3.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_4.ulc use_events=yes
Wrote events list to file ad24043000g200370l_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_4.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_5.ulc use_events=yes
Wrote events list to file ad24043000g200370l_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_5.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 0 6 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_6.ulc use_events=yes
Wrote events list to file ad24043000g200370l_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_6.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 6 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.evt
Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6 1 5 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200370l_7.ulc use_events=yes
Wrote events list to file ad24043000g200370l_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200370l_7.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 14 335 0 0 0
Writing events file
14 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 14 335 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_1.ulc use_events=yes
Wrote events list to file ad24043000g200470h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200470h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 27 322 0 0 0
Writing events file
27 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 27 322 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_2.ulc use_events=yes
Wrote events list to file ad24043000g200470h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200470h_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 18 331 0 0 0
Writing events file
18 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 18 331 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_3.ulc use_events=yes
Wrote events list to file ad24043000g200470h_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200470h_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 26 323 0 0 0
Writing events file
26 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 26 323 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_4.ulc use_events=yes
Wrote events list to file ad24043000g200470h_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g200470h_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 7 342 0 0 0
Writing events file
7 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 7 342 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_5.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_5.ulc use_events=yes
Wrote events list to file ad24043000g200470h_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200470h_5.ulc since it has 7 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 0 349 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 0 349 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_6.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_6.ulc use_events=yes
Wrote events list to file ad24043000g200470h_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad24043000g200470h_6.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 349 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.evt
Total Good Bad: Region Time Phase Cut
349 11 338 0 0 0
Writing events file
11 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
349 11 338 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region ad24043000g225670_7.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad24043000g200470h_7.ulc use_events=yes
Wrote events list to file ad24043000g200470h_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 1148 8250 0 0 0
Writing events file
1148 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 1148 8250 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_1.ulc use_events=yes
Wrote events list to file ad24043000g300170h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 502 8896 0 0 0
Writing events file
502 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 502 8896 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_2.ulc use_events=yes
Wrote events list to file ad24043000g300170h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 476 8922 0 0 0
Writing events file
476 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 476 8922 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_3.ulc use_events=yes
Wrote events list to file ad24043000g300170h_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 584 8814 0 0 0
Writing events file
584 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 584 8814 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_4.ulc use_events=yes
Wrote events list to file ad24043000g300170h_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 252 9146 0 0 0
Writing events file
252 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 252 9146 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_5.ulc use_events=yes
Wrote events list to file ad24043000g300170h_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_6.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 217 9181 0 0 0
Writing events file
217 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 217 9181 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_6.ulc use_events=yes
Wrote events list to file ad24043000g300170h_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300170h_7.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.22E+05 9398 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.evt
Total Good Bad: Region Time Phase Cut
9398 208 9190 0 0 0
Writing events file
208 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9398 208 9190 0 0 0
in 21524.57 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300170h_7.ulc use_events=yes
Wrote events list to file ad24043000g300170h_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 821 5822 0 0 0
Writing events file
821 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 821 5822 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_1.ulc use_events=yes
Wrote events list to file ad24043000g300270m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 380 6263 0 0 0
Writing events file
380 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 380 6263 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_2.ulc use_events=yes
Wrote events list to file ad24043000g300270m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 318 6325 0 0 0
Writing events file
318 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 318 6325 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_3.ulc use_events=yes
Wrote events list to file ad24043000g300270m_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 376 6267 0 0 0
Writing events file
376 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 376 6267 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_4.ulc use_events=yes
Wrote events list to file ad24043000g300270m_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 218 6425 0 0 0
Writing events file
218 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 218 6425 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_5.ulc use_events=yes
Wrote events list to file ad24043000g300270m_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_6.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 151 6492 0 0 0
Writing events file
151 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 151 6492 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_6.ulc use_events=yes
Wrote events list to file ad24043000g300270m_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300270m_7.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.15E+05 6643 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.evt
Total Good Bad: Region Time Phase Cut
6643 126 6517 0 0 0
Writing events file
126 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6643 126 6517 0 0 0
in 15279.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300270m_7.ulc use_events=yes
Wrote events list to file ad24043000g300270m_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300370l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_1.ulc use_events=yes
Wrote events list to file ad24043000g300370l_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_1.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_2.ulc use_events=yes
Wrote events list to file ad24043000g300370l_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_2.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_3.ulc use_events=yes
Wrote events list to file ad24043000g300370l_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_3.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 1 2 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_4.ulc use_events=yes
Wrote events list to file ad24043000g300370l_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_4.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_5.ulc use_events=yes
Wrote events list to file ad24043000g300370l_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_5.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_6.ulc use_events=yes
Wrote events list to file ad24043000g300370l_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_6.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.18E+02 3 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.evt
Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3 0 3 0 0 0
in 17.81 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300370l_7.ulc use_events=yes
Wrote events list to file ad24043000g300370l_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300370l_7.ulc since it has 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 9 364 0 0 0
Writing events file
9 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 9 364 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_1.ulc use_events=yes
Wrote events list to file ad24043000g300470h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300470h_1.ulc since it has 9 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
Writing events file
17 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_2.ulc use_events=yes
Wrote events list to file ad24043000g300470h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300470h_3.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 10 363 0 0 0
Writing events file
10 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 10 363 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_3.ulc use_events=yes
Wrote events list to file ad24043000g300470h_3.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300470h_4.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 23 350 0 0 0
Writing events file
23 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 23 350 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_4.ulc use_events=yes
Wrote events list to file ad24043000g300470h_4.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300470h_5.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
Writing events file
17 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 17 356 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_5.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_5.ulc use_events=yes
Wrote events list to file ad24043000g300470h_5.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000g300470h_6.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 6 367 0 0 0
Writing events file
6 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 6 367 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_6.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_6.ulc use_events=yes
Wrote events list to file ad24043000g300470h_6.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad24043000g300470h_6.ulc since it has 6 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.10E+04 373 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.evt
Total Good Bad: Region Time Phase Cut
373 11 362 0 0 0
Writing events file
11 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
373 11 362 0 0 0
in 1008.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region ad24043000g325670_7.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad24043000g300470h_7.ulc use_events=yes
Wrote events list to file ad24043000g300470h_7.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad24043000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 735 991 0 0 0
Writing events file
735 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1726 735 991 0 0 0
in 18893.13 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000102h_1.ulc use_events=yes
Wrote events list to file ad24043000s000102h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000102h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.19E+05 1726 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.evt
Total Good Bad: Region Time Phase Cut
1726 398 1328 0 0 0
Writing events file
398 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1726 398 1328 0 0 0
in 18893.13 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000102h_2.ulc use_events=yes
Wrote events list to file ad24043000s000102h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.evt
Total Good Bad: Region Time Phase Cut
1830 754 1076 0 0 0
Writing events file
754 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1830 754 1076 0 0 0
in 18893.13 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000112h_1.ulc use_events=yes
Wrote events list to file ad24043000s000112h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s000112h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.19E+05 1830 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.evt
Total Good Bad: Region Time Phase Cut
1830 429 1401 0 0 0
Writing events file
429 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1830 429 1401 0 0 0
in 18893.13 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000112h_2.ulc use_events=yes
Wrote events list to file ad24043000s000112h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 476 726 0 0 0
Writing events file
476 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1202 476 726 0 0 0
in 12997.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000202m_1.ulc use_events=yes
Wrote events list to file ad24043000s000202m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000202m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1202 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.evt
Total Good Bad: Region Time Phase Cut
1202 305 897 0 0 0
Writing events file
305 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1202 305 897 0 0 0
in 12997.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000202m_2.ulc use_events=yes
Wrote events list to file ad24043000s000202m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.evt
Total Good Bad: Region Time Phase Cut
1267 495 772 0 0 0
Writing events file
495 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1267 495 772 0 0 0
in 12997.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000212m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000212m_1.ulc use_events=yes
Wrote events list to file ad24043000s000212m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s000212m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1267 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.evt
Total Good Bad: Region Time Phase Cut
1267 319 948 0 0 0
Writing events file
319 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1267 319 948 0 0 0
in 12997.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000212m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000212m_2.ulc use_events=yes
Wrote events list to file ad24043000s000212m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s000402h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 117 140 0 0 0
Writing events file
117 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257 117 140 0 0 0
in 3377.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000402h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000402h_1.ulc use_events=yes
Wrote events list to file ad24043000s000402h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000402h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.34E+04 257 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.evt
Total Good Bad: Region Time Phase Cut
257 44 213 0 0 0
Writing events file
44 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257 44 213 0 0 0
in 3377.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000402h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad24043000s000402h_2.ulc use_events=yes
Wrote events list to file ad24043000s000402h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s000412h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.34E+04 275 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.evt
Total Good Bad: Region Time Phase Cut
275 120 155 0 0 0
Writing events file
120 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
275 120 155 0 0 0
in 3377.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000412h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000412h_1.ulc use_events=yes
Wrote events list to file ad24043000s000412h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s000412h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.34E+04 275 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.evt
Total Good Bad: Region Time Phase Cut
275 48 227 0 0 0
Writing events file
48 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
275 48 227 0 0 0
in 3377.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s000412h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad24043000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad24043000s000412h_2.ulc use_events=yes
Wrote events list to file ad24043000s000412h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 605 1010 0 0 0
Writing events file
605 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1615 605 1010 0 0 0
in 18907.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100102h_1.ulc use_events=yes
Wrote events list to file ad24043000s100102h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100102h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.19E+05 1615 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.evt
Total Good Bad: Region Time Phase Cut
1615 423 1192 0 0 0
Writing events file
423 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1615 423 1192 0 0 0
in 18907.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100102h_2.ulc use_events=yes
Wrote events list to file ad24043000s100102h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.evt
Total Good Bad: Region Time Phase Cut
1689 625 1064 0 0 0
Writing events file
625 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1689 625 1064 0 0 0
in 18907.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100112h_1.ulc use_events=yes
Wrote events list to file ad24043000s100112h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100112h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.19E+05 1689 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.evt
Total Good Bad: Region Time Phase Cut
1689 447 1242 0 0 0
Writing events file
447 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1689 447 1242 0 0 0
in 18907.16 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100112h_2.ulc use_events=yes
Wrote events list to file ad24043000s100112h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 382 652 0 0 0
Writing events file
382 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 382 652 0 0 0
in 12983.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100202m_1.ulc use_events=yes
Wrote events list to file ad24043000s100202m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100202m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.13E+05 1034 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.evt
Total Good Bad: Region Time Phase Cut
1034 312 722 0 0 0
Writing events file
312 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 312 722 0 0 0
in 12983.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100202m_2.ulc use_events=yes
Wrote events list to file ad24043000s100202m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.evt
Total Good Bad: Region Time Phase Cut
1075 394 681 0 0 0
Writing events file
394 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1075 394 681 0 0 0
in 12983.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100212m_1.ulc use_events=yes
Wrote events list to file ad24043000s100212m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100212m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.13E+05 1075 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.evt
Total Good Bad: Region Time Phase Cut
1075 318 757 0 0 0
Writing events file
318 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1075 318 757 0 0 0
in 12983.97 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100212m_2.ulc use_events=yes
Wrote events list to file ad24043000s100212m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100402h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 129 152 0 0 0
Writing events file
129 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
281 129 152 0 0 0
in 3511.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100402h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100402h_1.ulc use_events=yes
Wrote events list to file ad24043000s100402h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100402h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.35E+04 281 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.evt
Total Good Bad: Region Time Phase Cut
281 46 235 0 0 0
Writing events file
46 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
281 46 235 0 0 0
in 3511.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100402h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100402h_2.ulc use_events=yes
Wrote events list to file ad24043000s100402h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100412h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.evt
Total Good Bad: Region Time Phase Cut
297 134 163 0 0 0
Writing events file
134 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
297 134 163 0 0 0
in 3511.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100412h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100412h_1.ulc use_events=yes
Wrote events list to file ad24043000s100412h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100412h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.35E+04 297 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.evt
Total Good Bad: Region Time Phase Cut
297 49 248 0 0 0
Writing events file
49 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
297 49 248 0 0 0
in 3511.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100412h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100412h_2.ulc use_events=yes
Wrote events list to file ad24043000s100412h_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100502m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 38 75 0 0 0
Writing events file
38 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
113 38 75 0 0 0
in 1444.02 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100502m_1.ulc use_events=yes
Wrote events list to file ad24043000s100502m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100502m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.14E+04 113 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.evt
Total Good Bad: Region Time Phase Cut
113 18 95 0 0 0
Writing events file
18 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
113 18 95 0 0 0
in 1444.02 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad24043000s100502m_2.ulc use_events=yes
Wrote events list to file ad24043000s100502m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad24043000s100512m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.14E+04 120 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.evt
Total Good Bad: Region Time Phase Cut
120 39 81 0 0 0
Writing events file
39 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
120 39 81 0 0 0
in 1444.02 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100512m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100512m_1.ulc use_events=yes
Wrote events list to file ad24043000s100512m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad24043000s100512m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.14E+04 120 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.evt
Total Good Bad: Region Time Phase Cut
120 22 98 0 0 0
Writing events file
22 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
120 22 98 0 0 0
in 1444.02 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000s100512m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad24043000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad24043000s100512m_2.ulc use_events=yes
Wrote events list to file ad24043000s100512m_2.ulc
Changing Data directory from:
/data/data17/seq_proc/24043000.003/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 17371 Total of 0 sets of frame data are extracted.
1 ad24043000g200170h.unf 56287 1 ad24043000g200270m.unf 56287 1 ad24043000g200370l.unf 56287 1 ad24043000g200470h.unf 56287-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.97E+04 6757 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.97E+04 6757 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.unf
Total Good Bad: Region Time Phase Cut
26341 6803 19538 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.unf
Total Good Bad: Region Time Phase Cut
21476 5247 16229 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.unf
Total Good Bad: Region Time Phase Cut
6757 1904 4853 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.unf
Total Good Bad: Region Time Phase Cut
1713 471 1242 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
56287 14425 41862 0 0 0
in 60535.82 seconds
Spectrum has 14425 counts for 0.2383 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 60536. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > read events ad24043000g200470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad24043000g220170.cal group=yes
Wrote spectrum to ad24043000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 04:09:03 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad24043000g220170.cal
Net count rate (cts/s) for file 1 0.2383 +/- 1.9844E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.8199E+06 using 84 PHA bins.
Reduced chi-squared = 2.3635E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.8074E+06 using 84 PHA bins.
Reduced chi-squared = 2.3172E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.8074E+06 using 84 PHA bins.
Reduced chi-squared = 2.2879E+04
!XSPEC> renorm
Chi-Squared = 3647. using 84 PHA bins.
Reduced chi-squared = 46.16
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2830.5 0 1.000 5.893 0.1123 6.3701E-02
5.6190E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1169.5 0 1.000 5.864 0.1653 9.4157E-02
4.9751E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
535.66 -1 1.000 5.913 0.1870 0.1321
3.3511E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
489.31 -2 1.000 5.948 0.2040 0.1465
2.3429E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
484.20 -3 1.000 5.934 0.1933 0.1430
2.6894E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
483.79 -4 1.000 5.939 0.1961 0.1443
2.5518E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
483.61 -5 1.000 5.937 0.1947 0.1438
2.6021E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
483.61 0 1.000 5.937 0.1947 0.1439
2.5992E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93720 +/- 0.54273E-02
3 3 2 gaussian/b Sigma 0.194698 +/- 0.56131E-02
4 4 2 gaussian/b norm 0.143856 +/- 0.20647E-02
5 2 3 gaussian/b LineE 6.53689 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.204294 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.599159E-02 +/- 0.14995E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 483.6 using 84 PHA bins.
Reduced chi-squared = 6.122
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad24043000g220170.cal peaks at 5.93720 +/- 0.0054273 keV1 ad24043000g300170h.unf 54839 1 ad24043000g300270m.unf 54839 1 ad24043000g300370l.unf 54839 1 ad24043000g300470h.unf 54839-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.96E+04 6175 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
2 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
3 NGC_2023 PH LOW 01/03/96 06:26:04 0.96E+04 6175 1024
4 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1623 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.unf
Total Good Bad: Region Time Phase Cut
26001 4739 21262 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.unf
Total Good Bad: Region Time Phase Cut
21040 4115 16925 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.unf
Total Good Bad: Region Time Phase Cut
6175 1700 4475 0 0 0
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.unf
Total Good Bad: Region Time Phase Cut
1623 408 1215 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
54839 10962 43877 0 0 0
in 60333.82 seconds
Spectrum has 10962 counts for 0.1817 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 60334. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad24043000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!xsel:ASCA > read events ad24043000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > read events ad24043000g300470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad24043000g320170.cal group=yes
Wrote spectrum to ad24043000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 04:11:16 9-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad24043000g320170.cal
Net count rate (cts/s) for file 1 0.1817 +/- 1.7359E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.2118E+06 using 84 PHA bins.
Reduced chi-squared = 2.8724E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.1942E+06 using 84 PHA bins.
Reduced chi-squared = 2.8131E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.1942E+06 using 84 PHA bins.
Reduced chi-squared = 2.7775E+04
!XSPEC> renorm
Chi-Squared = 3827. using 84 PHA bins.
Reduced chi-squared = 48.45
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
3014.6 0 1.000 5.892 9.9573E-02 5.5190E-02
4.6899E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1079.4 0 1.000 5.864 0.1431 8.9213E-02
4.0274E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
262.16 -1 1.000 5.921 0.1494 0.1289
2.4670E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
224.12 -2 1.000 5.936 0.1541 0.1389
1.9778E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
222.82 -3 1.000 5.932 0.1499 0.1381
2.0610E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
222.82 -4 1.000 5.933 0.1503 0.1383
2.0441E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93284 +/- 0.41711E-02
3 3 2 gaussian/b Sigma 0.150258 +/- 0.52092E-02
4 4 2 gaussian/b norm 0.138274 +/- 0.17765E-02
5 2 3 gaussian/b LineE 6.53209 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.157664 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.044081E-02 +/- 0.10679E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 222.8 using 84 PHA bins.
Reduced chi-squared = 2.821
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad24043000g320170.cal peaks at 5.93284 +/- 0.0041711 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:37:34 0.25E+05 13141 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000102h.unf
Total Good Bad: Region Time Phase Cut
13141 925 0 12216 0 0
Writing events file
925 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13141 925 0 12216 0 0
in 1895.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 925
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 591
Flickering pixels iter, pixels & cnts : 1 4 27
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 925
Number of image cts rejected (N, %) : 618 66.8108139
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 925 0 0
Image cts rejected: 0 618 0 0
Image cts rej (%) : 0.00 66.81 0.00 0.00
filtering data...
Total counts : 0 925 0 0
Total cts rejected: 0 618 0 0
Total cts rej (%) : 0.00 66.81 0.00 0.00
Number of clean counts accepted : 307
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:37:34 0.25E+05 13589 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000112h.unf
Total Good Bad: Region Time Phase Cut
13589 1009 0 12580 0 0
Writing events file
1009 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13589 1009 0 12580 0 0
in 1895.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1009
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 591
Flickering pixels iter, pixels & cnts : 1 4 27
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 1009
Number of image cts rejected (N, %) : 618 61.2487602
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 1009 0 0
Image cts rejected: 0 618 0 0
Image cts rej (%) : 0.00 61.25 0.00 0.00
filtering data...
Total counts : 0 1009 0 0
Total cts rejected: 0 618 0 0
Total cts rej (%) : 0.00 61.25 0.00 0.00
Number of clean counts accepted : 391
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.23E+05 11050 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000202m.unf
Total Good Bad: Region Time Phase Cut
11050 1487 0 9563 0 0
Writing events file
1487 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11050 1487 0 9563 0 0
in 2761.62 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1487
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 1252
Flickering pixels iter, pixels & cnts : 1 4 26
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1487
Number of image cts rejected (N, %) : 1278 85.9448547
By chip : 0 1 2 3
Pixels rejected : 0 8 0 0
Image counts : 0 1487 0 0
Image cts rejected: 0 1278 0 0
Image cts rej (%) : 0.00 85.94 0.00 0.00
filtering data...
Total counts : 0 1487 0 0
Total cts rejected: 0 1278 0 0
Total cts rej (%) : 0.00 85.94 0.00 0.00
Number of clean counts accepted : 209
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.23E+05 11351 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000212m.unf
Total Good Bad: Region Time Phase Cut
11351 1526 0 9825 0 0
Writing events file
1526 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11351 1526 0 9825 0 0
in 2761.62 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1526
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 1252
Flickering pixels iter, pixels & cnts : 1 4 26
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1526
Number of image cts rejected (N, %) : 1278 83.7483597
By chip : 0 1 2 3
Pixels rejected : 0 8 0 0
Image counts : 0 1526 0 0
Image cts rejected: 0 1278 0 0
Image cts rej (%) : 0.00 83.75 0.00 0.00
filtering data...
Total counts : 0 1526 0 0
Total cts rejected: 0 1278 0 0
Total cts rej (%) : 0.00 83.75 0.00 0.00
Number of clean counts accepted : 248
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT LOW 01/03/96 10:40:54 0.12E+05 4120 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000302l.unf
Total Good Bad: Region Time Phase Cut
4120 2902 0 1218 0 0
Writing events file
2902 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4120 2902 0 1218 0 0
in 6317.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2902
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 2547
Flickering pixels iter, pixels & cnts : 1 6 46
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 2902
Number of image cts rejected (N, %) : 2593 89.3521729
By chip : 0 1 2 3
Pixels rejected : 0 11 0 0
Image counts : 0 2902 0 0
Image cts rejected: 0 2593 0 0
Image cts rej (%) : 0.00 89.35 0.00 0.00
filtering data...
Total counts : 0 2902 0 0
Total cts rejected: 0 2593 0 0
Total cts rej (%) : 0.00 89.35 0.00 0.00
Number of clean counts accepted : 309
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000312l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 LOW 01/03/96 10:40:54 0.12E+05 4217 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s000312l.unf
Total Good Bad: Region Time Phase Cut
4217 2992 0 1225 0 0
Writing events file
2992 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4217 2992 0 1225 0 0
in 6317.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000312l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2992
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 2547
Flickering pixels iter, pixels & cnts : 1 6 46
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 2992
Number of image cts rejected (N, %) : 2593 86.6644363
By chip : 0 1 2 3
Pixels rejected : 0 11 0 0
Image counts : 0 2992 0 0
Image cts rejected: 0 2593 0 0
Image cts rej (%) : 0.00 86.66 0.00 0.00
filtering data...
Total counts : 0 2992 0 0
Total cts rejected: 0 2593 0 0
Total cts rej (%) : 0.00 86.66 0.00 0.00
Number of clean counts accepted : 399
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s000402h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:47 0.51E+04 2106 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/ad24043000s000402h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000402h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad24043000s000402h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:47 0.51E+04 2181 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/ad24043000s000412h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s000412h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad24043000s000412h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 08:38:02 0.25E+05 64908 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100102h.unf
Total Good Bad: Region Time Phase Cut
64908 4421 0 60487 0 0
Writing events file
4421 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
64908 4421 0 60487 0 0
in 1895.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 4421
Total counts in chip images : 4420
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 17 4096
Flickering pixels iter, pixels & cnts : 1 5 47
Number of pixels rejected : 22
Number of (internal) image counts : 4420
Number of image cts rejected (N, %) : 4143 93.7330322
By chip : 0 1 2 3
Pixels rejected : 0 0 0 22
Image counts : 0 0 0 4420
Image cts rejected: 0 0 0 4143
Image cts rej (%) : 0.00 0.00 0.00 93.73
filtering data...
Total counts : 0 0 0 4421
Total cts rejected: 0 0 0 4144
Total cts rej (%) : 0.00 0.00 0.00 93.73
Number of clean counts accepted : 277
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 22
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 08:38:02 0.25E+05 65256 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100112h.unf
Total Good Bad: Region Time Phase Cut
65256 4487 0 60769 0 0
Writing events file
4487 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
65256 4487 0 60769 0 0
in 1895.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4487
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 17 4097
Flickering pixels iter, pixels & cnts : 1 5 47
Number of pixels rejected : 22
Number of (internal) image counts : 4487
Number of image cts rejected (N, %) : 4144 92.3556976
By chip : 0 1 2 3
Pixels rejected : 0 0 0 22
Image counts : 0 0 0 4487
Image cts rejected: 0 0 0 4144
Image cts rej (%) : 0.00 0.00 0.00 92.36
filtering data...
Total counts : 0 0 0 4487
Total cts rejected: 0 0 0 4144
Total cts rej (%) : 0.00 0.00 0.00 92.36
Number of clean counts accepted : 343
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 22
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 09:40:54 0.23E+05 60446 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100202m.unf
Total Good Bad: Region Time Phase Cut
60446 9507 0 50939 0 0
Writing events file
9507 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60446 9507 0 50939 0 0
in 2761.62 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 9507
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 22 9315
Flickering pixels iter, pixels & cnts : 1 4 30
Number of pixels rejected : 26
Number of (internal) image counts : 9507
Number of image cts rejected (N, %) : 9345 98.2959900
By chip : 0 1 2 3
Pixels rejected : 0 0 0 26
Image counts : 0 0 0 9507
Image cts rejected: 0 0 0 9345
Image cts rej (%) : 0.00 0.00 0.00 98.30
filtering data...
Total counts : 0 0 0 9507
Total cts rejected: 0 0 0 9345
Total cts rej (%) : 0.00 0.00 0.00 98.30
Number of clean counts accepted : 162
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 09:40:54 0.23E+05 60695 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100212m.unf
Total Good Bad: Region Time Phase Cut
60695 9523 0 51172 0 0
Writing events file
9523 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60695 9523 0 51172 0 0
in 2761.62 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 9523
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 22 9315
Flickering pixels iter, pixels & cnts : 1 4 30
Number of pixels rejected : 26
Number of (internal) image counts : 9523
Number of image cts rejected (N, %) : 9345 98.1308441
By chip : 0 1 2 3
Pixels rejected : 0 0 0 26
Image counts : 0 0 0 9523
Image cts rejected: 0 0 0 9345
Image cts rej (%) : 0.00 0.00 0.00 98.13
filtering data...
Total counts : 0 0 0 9523
Total cts rejected: 0 0 0 9345
Total cts rej (%) : 0.00 0.00 0.00 98.13
Number of clean counts accepted : 178
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT LOW 01/03/96 10:40:54 0.12E+05 12398 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100302l.unf
Total Good Bad: Region Time Phase Cut
12398 8682 0 3716 0 0
Writing events file
8682 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12398 8682 0 3716 0 0
in 6317.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8682
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 19 8497
Flickering pixels iter, pixels & cnts : 1 2 6
Number of pixels rejected : 21
Number of (internal) image counts : 8682
Number of image cts rejected (N, %) : 8503 97.9382629
By chip : 0 1 2 3
Pixels rejected : 0 0 0 21
Image counts : 0 0 0 8682
Image cts rejected: 0 0 0 8503
Image cts rej (%) : 0.00 0.00 0.00 97.94
filtering data...
Total counts : 0 0 0 8682
Total cts rejected: 0 0 0 8503
Total cts rej (%) : 0.00 0.00 0.00 97.94
Number of clean counts accepted : 179
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100312l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 LOW 01/03/96 10:40:54 0.12E+05 12453 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100312l.unf
Total Good Bad: Region Time Phase Cut
12453 8718 0 3735 0 0
Writing events file
8718 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12453 8718 0 3735 0 0
in 6317.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 8718
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 19 8497
Flickering pixels iter, pixels & cnts : 1 2 6
Number of pixels rejected : 21
Number of (internal) image counts : 8718
Number of image cts rejected (N, %) : 8503 97.5338364
By chip : 0 1 2 3
Pixels rejected : 0 0 0 21
Image counts : 0 0 0 8718
Image cts rejected: 0 0 0 8503
Image cts rej (%) : 0.00 0.00 0.00 97.53
filtering data...
Total counts : 0 0 0 8718
Total cts rejected: 0 0 0 8503
Total cts rej (%) : 0.00 0.00 0.00 97.53
Number of clean counts accepted : 215
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100402h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT HIGH 01/03/96 05:12:43 0.52E+04 9767 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/ad24043000s100402h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad24043000s100402h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 HIGH 01/03/96 05:12:43 0.52E+04 9835 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/24043000.003/ad24043000s100412h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100412h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad24043000s100412h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT MEDIUM 01/03/96 05:41:26 0.21E+04 3950 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100502m.unf
Total Good Bad: Region Time Phase Cut
3950 131 0 3819 0 0
Writing events file
131 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3950 131 0 3819 0 0
in 73.72 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad24043000s100502m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100502m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 131
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 122
Number of pixels rejected : 7
Number of (internal) image counts : 131
Number of image cts rejected (N, %) : 122 93.1297684
By chip : 0 1 2 3
Pixels rejected : 0 0 0 7
Image counts : 0 0 0 131
Image cts rejected: 0 0 0 122
Image cts rej (%) : 0.00 0.00 0.00 93.13
filtering data...
Total counts : 0 0 0 131
Total cts rejected: 0 0 0 122
Total cts rej (%) : 0.00 0.00 0.00 93.13
Number of clean counts accepted : 9
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000s100512m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_2023 BRIGHT2 MEDIUM 01/03/96 05:41:26 0.21E+04 3979 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000s100512m.unf
Total Good Bad: Region Time Phase Cut
3979 133 0 3846 0 0
Writing events file
133 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3979 133 0 3846 0 0
in 73.72 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000s100512m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad24043000s100512m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad24043000s100512m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 133
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 122
Number of pixels rejected : 7
Number of (internal) image counts : 133
Number of image cts rejected (N, %) : 122 91.7293243
By chip : 0 1 2 3
Pixels rejected : 0 0 0 7
Image counts : 0 0 0 133
Image cts rejected: 0 0 0 122
Image cts rej (%) : 0.00 0.00 0.00 91.73
filtering data...
Total counts : 0 0 0 133
Total cts rejected: 0 0 0 122
Total cts rej (%) : 0.00 0.00 0.00 91.73
Number of clean counts accepted : 11
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad24043000g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.unf
Total Good Bad: Region Time Phase Cut
26341 341 0 26000 0 0
Writing events file
341 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26341 341 0 26000 0 0
in 637.28 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26341 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200170h.unf
Total Good Bad: Region Time Phase Cut
26341 78 0 26263 0 0
Writing events file
78 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26341 78 0 26263 0 0
in 80.48 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.unf
Total Good Bad: Region Time Phase Cut
21476 1451 0 20025 0 0
Writing events file
1451 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21476 1451 0 20025 0 0
in 2423.64 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200270m.unf
Total Good Bad: Region Time Phase Cut
21476 3355 0 18121 0 0
Writing events file
3355 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21476 3355 0 18121 0 0
in 3105.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g200370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.97E+04 6757 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.unf
Total Good Bad: Region Time Phase Cut
6757 2715 0 4042 0 0
Writing events file
2715 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6757 2715 0 4042 0 0
in 4742.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.97E+04 6757 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200370l.unf
Total Good Bad: Region Time Phase Cut
6757 3647 0 3110 0 0
Writing events file
3647 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6757 3647 0 3110 0 0
in 4558.19 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g200470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.unf
Total Good Bad: Region Time Phase Cut
1713 584 0 1129 0 0
Writing events file
584 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1713 584 0 1129 0 0
in 960.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad24043000g200470h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g200470h.unf
Total Good Bad: Region Time Phase Cut
1713 125 0 1588 0 0
Writing events file
125 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1713 125 0 1588 0 0
in 225.90 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.unf
Total Good Bad: Region Time Phase Cut
26001 335 0 25666 0 0
Writing events file
335 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26001 335 0 25666 0 0
in 637.28 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 05:12:51 0.26E+05 26001 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300170h.unf
Total Good Bad: Region Time Phase Cut
26001 80 0 25921 0 0
Writing events file
80 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26001 80 0 25921 0 0
in 80.48 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.unf
Total Good Bad: Region Time Phase Cut
21040 1298 0 19742 0 0
Writing events file
1298 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21040 1298 0 19742 0 0
in 2423.64 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH MEDIUM 01/03/96 05:42:04 0.22E+05 21040 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300270m.unf
Total Good Bad: Region Time Phase Cut
21040 2848 0 18192 0 0
Writing events file
2848 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21040 2848 0 18192 0 0
in 3105.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g300370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.96E+04 6175 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.unf
Total Good Bad: Region Time Phase Cut
6175 2437 0 3738 0 0
Writing events file
2437 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6175 2437 0 3738 0 0
in 4614.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH LOW 01/03/96 06:26:04 0.96E+04 6175 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300370l.unf
Total Good Bad: Region Time Phase Cut
6175 3388 0 2787 0 0
Writing events file
3388 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6175 3388 0 2787 0 0
in 4558.19 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad24043000g300470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1623 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.unf
Total Good Bad: Region Time Phase Cut
1623 502 0 1121 0 0
Writing events file
502 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1623 502 0 1121 0 0
in 960.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad24043000g300470h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_2023 PH HIGH 01/03/96 13:32:04 0.23E+04 1623 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/24043000.003/ad24043000g300470h.unf
Total Good Bad: Region Time Phase Cut
1623 121 0 1502 0 0
Writing events file
121 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1623 121 0 1502 0 0
in 225.90 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/24043000.003/
Setting mkf directory to /data/data17/seq_proc/24043000.003/
!earthevents:ASCA > read events ad24043000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/24043000.003/
HK Directory is: /data/data17/seq_proc/24043000.003/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad24043000s000102h.unf|S0_LVDL1|134|S0 event discrimination lower level for ccd 1 ad24043000s000402h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1-> listing ad24043000s000102h.unf
ad24043000s000112h.unf|S0_LVDL1|134|S0 event discrimination lower level for ccd 1 ad24043000s000412h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1-> listing ad24043000s000112h.unf
ad24043000s000101h.unf|S0_LVDL1|134|S0 event discrimination lower level for ccd 1 ad24043000s000401h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1-> listing ad24043000s000101h.unf
ad24043000s000201m.unf|S0_LVDL1|134|S0 event discrimination lower level for ccd 1 ad24043000s000501m.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1-> listing ad24043000s000201m.unf
ad24043000s000301l.unf|S0_LVDL1|134|S0 event discrimination lower level for ccd 1 ad24043000s000601l.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1-> listing ad24043000s000301l.unf
ad24043000s100102h.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100402h.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100102h.unf
ad24043000s100202m.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100502m.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100202m.unf
ad24043000s100112h.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100412h.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100112h.unf
ad24043000s100212m.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100512m.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100212m.unf
ad24043000s100101h.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100401h.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100101h.unf
ad24043000s100201m.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100501m.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100201m.unf
ad24043000s100301l.unf|S1_LVDL3|148|S1 event discrimination lower level for ccd 3 ad24043000s100601l.unf|S1_LVDL3|216|S1 event discrimination lower level for ccd 3-> listing ad24043000s100301l.unf
ad24043000g200170h.unf|CPU2|RUN|CPU2 run/stop ad24043000g200470h.unf|CPU2|STOP|CPU2 run/stop ad24043000g200170h.unf|CPU3|RUN|CPU3 run/stop ad24043000g200470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad24043000g200170h.unf
ad24043000g300170h.unf|CPU2|RUN|CPU2 run/stop ad24043000g300470h.unf|CPU2|STOP|CPU2 run/stop ad24043000g300170h.unf|CPU3|RUN|CPU3 run/stop ad24043000g300470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad24043000g300170h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files