Processing Job Log for Sequence 26032000, version 004

This is the complete and detailed record of how this sequence was processed.

The following information is also available:

Processing started (10:28:13)

Checking input files for validity (10:28:15)

-> Verifying the input files
-> FITS file fa980513_1751.0800 exists
-> FITS file ft980513_1751.0800 exists
-> FITS file ad26032000_input.cat exists
-> Calculating Observation start and end times
-> Fetching leapsec.fits from /aps/calibration
-> leapsec.fits is already present in the working directory
-> Observation begins 1.6923550E+08 = 1998-05-13 17:51:36
-> Observation ends 1.6928643E+08 = 1998-05-14 08:00:26

Determine nominal pointing (10:28:21)

-> Checking fa980513_1751.0800 for problems
-> Fetching asca_mean_1999-04-23.fits from /aps/calibration
-> stdout output from aspect
Spacecraft Euler Angles: Phi=-55.07989 Theta=46.31471 Psi=24.82382
Telescope pointing: R.A.=305.15981 Dec=43.91083 Roll=294.65792 degrees
-> Nominal spacecraft Euler angles: Phi=-55.079892190785 Theta=46.314712368618 Psi=24.823818438807
-> Nominal telescope pointing: R.A.=305.15980548092 Dec=43.910830017261 Roll Angle=294.65791874547
-> Galactic Coordinates: Lii=80.994502 Bii=4.183135

Running frfread on telemetry files (10:28:31)

-> Running frfread on ft980513_1751.0800
-> stdout output from frfread4
53.9998 second gap between superframes 1660 and 1661
Dropping SF 2034 with inconsistent datamode 0/4
Dropping SF 2572 with inconsistent datamode 0/17
1.99999 second gap between superframes 3116 and 3117
Dropping SF 3968 with inconsistent datamode 0/31
FAINT event CCD=0, but using exposure CCD=3 time=169261786.04932
SIS0 coordinate error time=169261822.0492 x=1 y=121 pha[0]=1220 chip=0
SIS0 peak error time=169261822.0492 x=1 y=121 ph0=1220 ph1=1836 ph2=3978 ph3=3424
FAINT event CCD=0, but using exposure CCD=1 time=169261822.0492
Dropping SF 4347 with synch code word 0 = 255 not 250
1.99999 second gap between superframes 5374 and 5375
Dropping SF 6295 with inconsistent datamode 0/6
FAINT event CCD=0, but using exposure CCD=1 time=169267858.02886
GIS3 coordinate error time=169267894.42817 x=0 y=0 pha=544 rise=0
Dropping SF 6664 with inconsistent datamode 0/31
Dropped 1st C3 read after clocking change in ft980513_1751_0800S003001H.fits
Dropped 1st C0 read after clocking change in ft980513_1751_0800S003001H.fits
Dropped 1st C1 read after clocking change in ft980513_1751_0800S003401M.fits
GIS3 coordinate error time=169273375.82367 x=0 y=0 pha=256 rise=0
GIS3 coordinate error time=169273376.03461 x=0 y=0 pha=288 rise=0
Dropping SF 8520 with inconsistent datamode 0/6
SIS1 coordinate error time=169273370.01018 x=505 y=189 pha[0]=3850 chip=3
SIS1 peak error time=169273370.01018 x=33 y=221 ph0=894 ph5=3043 ph6=2772
SIS1 peak error time=169273370.01018 x=216 y=273 ph0=338 ph6=3043 ph7=3061
SIS1 peak error time=169273370.01018 x=71 y=328 ph0=1976 ph1=3447
SIS1 coordinate error time=169273370.01018 x=0 y=1 pha[0]=4070 chip=0
FAINT event CCD=0, but using exposure CCD=3 time=169273370.01018
SIS1 coordinate error time=169273370.01018 x=192 y=0 pha[0]=0 chip=1
FAINT event CCD=1, but using exposure CCD=3 time=169273370.01018
GIS3 coordinate error time=169273451.55778 x=0 y=0 pha=768 rise=0
GIS2 coordinate error time=169273452.03825 x=0 y=0 pha=338 rise=0
7.99997 second gap between superframes 8557 and 8558
53.9998 second gap between superframes 8610 and 8611
Warning: GIS2 bit assignment changed between 169273750.1339 and 169273752.1339
Warning: GIS3 bit assignment changed between 169273754.13389 and 169273756.13388
Warning: GIS2 bit assignment changed between 169273764.13386 and 169273766.13385
Warning: GIS3 bit assignment changed between 169273772.13383 and 169273774.13382
GIS3 coordinate error time=169274323.86732 x=0 y=0 pha=128 rise=0
SIS1 coordinate error time=169274314.00697 x=0 y=505 pha[0]=1664 chip=0
FAINT event CCD=0, but using exposure CCD=3 time=169274314.00697
SIS1 coordinate error time=169274314.00697 x=502 y=0 pha[0]=0 chip=1
SIS1 peak error time=169274314.00697 x=502 y=0 ph0=0 ph3=800 ph5=746 ph6=3607 ph7=766 ph8=985
FAINT event CCD=1, but using exposure CCD=3 time=169274314.00697
SIS1 coordinate error time=169274314.00697 x=0 y=15 pha[0]=1966 chip=0
SIS1 peak error time=169274314.00697 x=0 y=15 ph0=1966 ph2=2833 ph8=3581
FAINT event CCD=0, but using exposure CCD=3 time=169274314.00697
SIS1 coordinate error time=169274314.00697 x=0 y=420 pha[0]=3456 chip=0
FAINT event CCD=0, but using exposure CCD=3 time=169274314.00697
Dropping SF 8963 with corrupted frame indicator
Dropping SF 8964 with inconsistent datamode 0/31
Dropping SF 8965 with invalid bit rate 7
Dropped 1st C1 read after clocking change in ft980513_1751_0800S103901H.fits
Dropped 1st C2 read after clocking change in ft980513_1751_0800S103901H.fits
Dropped 1st C3 read after clocking change in ft980513_1751_0800S104201M.fits
Dropping SF 10601 with inconsistent datamode 0/31
Dropping SF 10602 with inconsistent datamode 0/31
SIS1 coordinate error time=169279065.99092 x=7 y=457 pha[0]=864 chip=0
FAINT event CCD=0, but using exposure CCD=3 time=169279065.99092
SIS1 coordinate error time=169279065.99092 x=0 y=0 pha[0]=2 chip=0
SIS1 peak error time=169279065.99092 x=0 y=0 ph0=2 ph1=2540
FAINT event CCD=0, but using exposure CCD=3 time=169279065.99092
SIS1 coordinate error time=169279161.99059 x=0 y=0 pha[0]=21 chip=0
SIS1 peak error time=169279161.99059 x=0 y=0 ph0=21 ph1=1984
FAINT event CCD=0, but using exposure CCD=3 time=169279161.99059
Dropping SF 10746 with synch code word 0 = 199 not 250
FAINT event CCD=2, but using exposure CCD=3 time=169279445.98963
GIS2 coordinate error time=169279462.88901 x=193 y=0 pha=1 rise=0
GIS3 coordinate error time=169279464.67026 x=0 y=0 pha=256 rise=0
SIS0 coordinate error time=169279457.98959 x=0 y=0 pha[0]=224 chip=0
SIS0 peak error time=169279457.98959 x=0 y=0 ph0=224 ph1=1984
FAINT event CCD=0, but using exposure CCD=1 time=169279457.98959
SIS0 coordinate error time=169279457.98959 x=0 y=0 pha[0]=9 chip=0
SIS0 peak error time=169279457.98959 x=0 y=0 ph0=9 ph1=1489 ph2=2464 ph3=2416
FAINT event CCD=0, but using exposure CCD=1 time=169279457.98959
SIS0 coordinate error time=169279457.98959 x=189 y=0 pha[0]=0 chip=3
FAINT event CCD=3, but using exposure CCD=1 time=169279457.98959
Dropping SF 10842 with inconsistent datamode 0/31
Dropping SF 10889 with inconsistent datamode 0/12
Dropping SF 10890 with inconsistent datamode 0/16
Dropping SF 10891 with inconsistent datamode 0/1
Dropping SF 10892 with synch code word 2 = 33 not 32
Dropping SF 10893 with inconsistent datamode 0/12
Dropping SF 10894 with synch code word 0 = 154 not 250
Dropping SF 10895 with synch code word 1 = 147 not 243
Dropping SF 10896 with inconsistent datamode 0/16
Dropping SF 10897 with inconsistent datamode 0/3
Dropping SF 11180 with inconsistent datamode 0/12
Dropping SF 11181 with corrupted frame indicator
Dropping SF 11182 with synch code word 0 = 246 not 250
Dropping SF 11183 with synch code word 0 = 202 not 250
Dropping SF 11184 with synch code word 1 = 195 not 243
Dropping SF 11185 with synch code word 0 = 156 not 250
Dropping SF 11186 with synch code word 0 = 58 not 250
GIS2 coordinate error time=169281333.01462 x=0 y=0 pha=768 rise=0
GIS2 coordinate error time=169281342.13962 x=96 y=0 pha=0 rise=0
SIS1 peak error time=169281305.98337 x=404 y=80 ph0=312 ph7=2053
SIS0 coordinate error time=169281329.98337 x=0 y=192 pha[0]=0 chip=0
FAINT event CCD=0, but using exposure CCD=1 time=169281329.98337
Dropping SF 11189 with corrupted frame indicator
SIS0 coordinate error time=169281541.98273 x=274 y=481 pha=1456 grade=4
SIS0 coordinate error time=169281541.98273 x=4 y=448 pha=1120 grade=6
SIS0 coordinate error time=169281541.98273 x=457 y=93 pha=255 grade=2
SIS0 coordinate error time=169281541.98273 x=331 y=464 pha=577 grade=5
SIS0 coordinate error time=169281541.98273 x=457 y=54 pha=1803 grade=0
SIS0 coordinate error time=169281541.98273 x=370 y=479 pha=1655 grade=1
SIS0 coordinate error time=169281541.98273 x=239 y=456 pha=704 grade=5
SIS0 coordinate error time=169281541.98273 x=208 y=476 pha=222 grade=5
GIS2 coordinate error time=169281695.13855 x=128 y=0 pha=1 rise=0
11439 of 11470 super frames processed
-> 0% of superframes in ft980513_1751.0800 corrupted
-> Deleting the following files with NEVENTS=0
ft980513_1751_0800G200170M.fits
ft980513_1751_0800G200270L.fits
ft980513_1751_0800G201070L.fits
ft980513_1751_0800G201170M.fits
ft980513_1751_0800G201270M.fits
ft980513_1751_0800G201370M.fits
ft980513_1751_0800G201470M.fits
ft980513_1751_0800G201870L.fits
ft980513_1751_0800G201970M.fits
ft980513_1751_0800G202070M.fits
ft980513_1751_0800G202170M.fits
ft980513_1751_0800G202270M.fits
ft980513_1751_0800G203470L.fits
ft980513_1751_0800G203570M.fits
ft980513_1751_0800G204070H.fits
ft980513_1751_0800G204170H.fits
ft980513_1751_0800G204270M.fits
ft980513_1751_0800G204370H.fits
ft980513_1751_0800G204470H.fits
ft980513_1751_0800G205070H.fits
ft980513_1751_0800G205170M.fits
ft980513_1751_0800G205270H.fits
ft980513_1751_0800G205370H.fits
ft980513_1751_0800G206170H.fits
ft980513_1751_0800G206270H.fits
ft980513_1751_0800G206370M.fits
ft980513_1751_0800G206470H.fits
ft980513_1751_0800G206570H.fits
ft980513_1751_0800G207170H.fits
ft980513_1751_0800G207270H.fits
ft980513_1751_0800G207370H.fits
ft980513_1751_0800G207470H.fits
ft980513_1751_0800G207570H.fits
ft980513_1751_0800G208270H.fits
ft980513_1751_0800G208370H.fits
ft980513_1751_0800G208470M.fits
ft980513_1751_0800G208570H.fits
ft980513_1751_0800G208670H.fits
ft980513_1751_0800G209570M.fits
ft980513_1751_0800G300170M.fits
ft980513_1751_0800G300270L.fits
ft980513_1751_0800G301070L.fits
ft980513_1751_0800G301170M.fits
ft980513_1751_0800G301270M.fits
ft980513_1751_0800G301370M.fits
ft980513_1751_0800G301470M.fits
ft980513_1751_0800G301870L.fits
ft980513_1751_0800G301970M.fits
ft980513_1751_0800G302070M.fits
ft980513_1751_0800G302170M.fits
ft980513_1751_0800G302270M.fits
ft980513_1751_0800G302770H.fits
ft980513_1751_0800G303470L.fits
ft980513_1751_0800G303570M.fits
ft980513_1751_0800G304170H.fits
ft980513_1751_0800G304270M.fits
ft980513_1751_0800G304370H.fits
ft980513_1751_0800G304470H.fits
ft980513_1751_0800G304570H.fits
ft980513_1751_0800G304970H.fits
ft980513_1751_0800G305070H.fits
ft980513_1751_0800G305170M.fits
ft980513_1751_0800G305270H.fits
ft980513_1751_0800G305470H.fits
ft980513_1751_0800G306170H.fits
ft980513_1751_0800G306270H.fits
ft980513_1751_0800G306370M.fits
ft980513_1751_0800G306470H.fits
ft980513_1751_0800G307170H.fits
ft980513_1751_0800G307270H.fits
ft980513_1751_0800G307370H.fits
ft980513_1751_0800G307970H.fits
ft980513_1751_0800G308070H.fits
ft980513_1751_0800G308170M.fits
ft980513_1751_0800G308270H.fits
ft980513_1751_0800G308470H.fits
ft980513_1751_0800G309270M.fits
ft980513_1751_0800S000401M.fits
ft980513_1751_0800S001101L.fits
ft980513_1751_0800S001701L.fits
ft980513_1751_0800S003301M.fits
ft980513_1751_0800S003401M.fits
ft980513_1751_0800S004201H.fits
ft980513_1751_0800S100401M.fits
ft980513_1751_0800S101101L.fits
ft980513_1751_0800S101701L.fits
ft980513_1751_0800S103201M.fits
ft980513_1751_0800S104401H.fits
-> merging GTIs for s0 980513_1751.0800
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980513_1751_0800S0HK.fits
-> Total ONTIME for s0 980513_1751.0800 = 43207.9
-> merging GTIs for s1 980513_1751.0800
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980513_1751_0800S1HK.fits
-> Total ONTIME for s1 980513_1751.0800 = 43235.9
-> merging GTIs for g2 980513_1751.0800
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980513_1751_0800G2HK.fits
-> Total ONTIME for g2 980513_1751.0800 = 34111.9
-> merging GTIs for g3 980513_1751.0800
-> sorting GTIs and removing invalid rows
-> Appending merged GTIs to ft980513_1751_0800G3HK.fits
-> Total ONTIME for g3 980513_1751.0800 = 34113.9

Merging event files from frfread (10:36:22)

-> Grouping s0 event files
-> stdout output from group_event_files
1 ft980513_1751_0800S001401H.fits 220465
1 ft980513_1751_0800S001901H.fits 220465
1 ft980513_1751_0800S002301H.fits 220465
1 ft980513_1751_0800S002701H.fits 220465
1 ft980513_1751_0800S002901H.fits 220465
1 ft980513_1751_0800S003601H.fits 220465
1 ft980513_1751_0800S003801H.fits 220465
1 ft980513_1751_0800S003901H.fits 220465
1 ft980513_1751_0800S004301H.fits 220465
2 ft980513_1751_0800S000101M.fits 69668
2 ft980513_1751_0800S000301M.fits 69668
2 ft980513_1751_0800S000501M.fits 69668
2 ft980513_1751_0800S000901M.fits 69668
2 ft980513_1751_0800S001301M.fits 69668
2 ft980513_1751_0800S001501M.fits 69668
2 ft980513_1751_0800S001801M.fits 69668
2 ft980513_1751_0800S002001M.fits 69668
2 ft980513_1751_0800S002201M.fits 69668
2 ft980513_1751_0800S002401M.fits 69668
2 ft980513_1751_0800S002601M.fits 69668
2 ft980513_1751_0800S002801M.fits 69668
2 ft980513_1751_0800S003501M.fits 69668
2 ft980513_1751_0800S003701M.fits 69668
2 ft980513_1751_0800S004001M.fits 69668
2 ft980513_1751_0800S004901M.fits 69668
3 ft980513_1751_0800S000201L.fits 7740
3 ft980513_1751_0800S000601L.fits 7740
3 ft980513_1751_0800S000801L.fits 7740
3 ft980513_1751_0800S001001L.fits 7740
3 ft980513_1751_0800S001201L.fits 7740
3 ft980513_1751_0800S001601L.fits 7740
3 ft980513_1751_0800S004401L.fits 7740
3 ft980513_1751_0800S004501L.fits 7740
3 ft980513_1751_0800S004701L.fits 7740
3 ft980513_1751_0800S004801L.fits 7740
4 ft980513_1751_0800S003001H.fits 4331
4 ft980513_1751_0800S003101H.fits 4331
5 ft980513_1751_0800S002101M.fits 74
5 ft980513_1751_0800S002501M.fits 74
5 ft980513_1751_0800S004101M.fits 74
6 ft980513_1751_0800S000701L.fits 47
7 ft980513_1751_0800S003201H.fits 36
8 ft980513_1751_0800S004602L.fits 20
-> Creating ad26032000s000101h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  9  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 9 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S001401H.fits 
 2 -- ft980513_1751_0800S001901H.fits 
 3 -- ft980513_1751_0800S002301H.fits 
 4 -- ft980513_1751_0800S002701H.fits 
 5 -- ft980513_1751_0800S002901H.fits 
 6 -- ft980513_1751_0800S003601H.fits 
 7 -- ft980513_1751_0800S003801H.fits 
 8 -- ft980513_1751_0800S003901H.fits 
 9 -- ft980513_1751_0800S004301H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S001401H.fits 
 2 -- ft980513_1751_0800S001901H.fits 
 3 -- ft980513_1751_0800S002301H.fits 
 4 -- ft980513_1751_0800S002701H.fits 
 5 -- ft980513_1751_0800S002901H.fits 
 6 -- ft980513_1751_0800S003601H.fits 
 7 -- ft980513_1751_0800S003801H.fits 
 8 -- ft980513_1751_0800S003901H.fits 
 9 -- ft980513_1751_0800S004301H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s000201m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  16  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 16 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S000101M.fits 
 2 -- ft980513_1751_0800S000301M.fits 
 3 -- ft980513_1751_0800S000501M.fits 
 4 -- ft980513_1751_0800S000901M.fits 
 5 -- ft980513_1751_0800S001301M.fits 
 6 -- ft980513_1751_0800S001501M.fits 
 7 -- ft980513_1751_0800S001801M.fits 
 8 -- ft980513_1751_0800S002001M.fits 
 9 -- ft980513_1751_0800S002201M.fits 
 10 -- ft980513_1751_0800S002401M.fits 
 11 -- ft980513_1751_0800S002601M.fits 
 12 -- ft980513_1751_0800S002801M.fits 
 13 -- ft980513_1751_0800S003501M.fits 
 14 -- ft980513_1751_0800S003701M.fits 
 15 -- ft980513_1751_0800S004001M.fits 
 16 -- ft980513_1751_0800S004901M.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S000101M.fits 
 2 -- ft980513_1751_0800S000301M.fits 
 3 -- ft980513_1751_0800S000501M.fits 
 4 -- ft980513_1751_0800S000901M.fits 
 5 -- ft980513_1751_0800S001301M.fits 
 6 -- ft980513_1751_0800S001501M.fits 
 7 -- ft980513_1751_0800S001801M.fits 
 8 -- ft980513_1751_0800S002001M.fits 
 9 -- ft980513_1751_0800S002201M.fits 
 10 -- ft980513_1751_0800S002401M.fits 
 11 -- ft980513_1751_0800S002601M.fits 
 12 -- ft980513_1751_0800S002801M.fits 
 13 -- ft980513_1751_0800S003501M.fits 
 14 -- ft980513_1751_0800S003701M.fits 
 15 -- ft980513_1751_0800S004001M.fits 
 16 -- ft980513_1751_0800S004901M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s000301l.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  10  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 10 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S000201L.fits 
 2 -- ft980513_1751_0800S000601L.fits 
 3 -- ft980513_1751_0800S000801L.fits 
 4 -- ft980513_1751_0800S001001L.fits 
 5 -- ft980513_1751_0800S001201L.fits 
 6 -- ft980513_1751_0800S001601L.fits 
 7 -- ft980513_1751_0800S004401L.fits 
 8 -- ft980513_1751_0800S004501L.fits 
 9 -- ft980513_1751_0800S004701L.fits 
 10 -- ft980513_1751_0800S004801L.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S000201L.fits 
 2 -- ft980513_1751_0800S000601L.fits 
 3 -- ft980513_1751_0800S000801L.fits 
 4 -- ft980513_1751_0800S001001L.fits 
 5 -- ft980513_1751_0800S001201L.fits 
 6 -- ft980513_1751_0800S001601L.fits 
 7 -- ft980513_1751_0800S004401L.fits 
 8 -- ft980513_1751_0800S004501L.fits 
 9 -- ft980513_1751_0800S004701L.fits 
 10 -- ft980513_1751_0800S004801L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s000401h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 2 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S003001H.fits 
 2 -- ft980513_1751_0800S003101H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S003001H.fits 
 2 -- ft980513_1751_0800S003101H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 74 events ft980513_1751_0800S002101M.fits ft980513_1751_0800S002501M.fits ft980513_1751_0800S004101M.fits
-> Ignoring the following files containing 47 events ft980513_1751_0800S000701L.fits
-> Ignoring the following files containing 36 events ft980513_1751_0800S003201H.fits
-> Ignoring the following files containing 20 events ft980513_1751_0800S004602L.fits
-> Grouping s1 event files
-> stdout output from group_event_files
1 ft980513_1751_0800S101401H.fits 214493
1 ft980513_1751_0800S101901H.fits 214493
1 ft980513_1751_0800S102301H.fits 214493
1 ft980513_1751_0800S102701H.fits 214493
1 ft980513_1751_0800S102901H.fits 214493
1 ft980513_1751_0800S103001H.fits 214493
1 ft980513_1751_0800S103401H.fits 214493
1 ft980513_1751_0800S103501H.fits 214493
1 ft980513_1751_0800S103801H.fits 214493
1 ft980513_1751_0800S104501H.fits 214493
2 ft980513_1751_0800S100101M.fits 96488
2 ft980513_1751_0800S100301M.fits 96488
2 ft980513_1751_0800S100501M.fits 96488
2 ft980513_1751_0800S100901M.fits 96488
2 ft980513_1751_0800S101301M.fits 96488
2 ft980513_1751_0800S101501M.fits 96488
2 ft980513_1751_0800S101801M.fits 96488
2 ft980513_1751_0800S102001M.fits 96488
2 ft980513_1751_0800S102201M.fits 96488
2 ft980513_1751_0800S102401M.fits 96488
2 ft980513_1751_0800S102601M.fits 96488
2 ft980513_1751_0800S102801M.fits 96488
2 ft980513_1751_0800S103301M.fits 96488
2 ft980513_1751_0800S103601M.fits 96488
2 ft980513_1751_0800S103701M.fits 96488
2 ft980513_1751_0800S104201M.fits 96488
2 ft980513_1751_0800S104901M.fits 96488
3 ft980513_1751_0800S100201L.fits 8015
3 ft980513_1751_0800S100601L.fits 8015
3 ft980513_1751_0800S100801L.fits 8015
3 ft980513_1751_0800S101001L.fits 8015
3 ft980513_1751_0800S101201L.fits 8015
3 ft980513_1751_0800S101601L.fits 8015
3 ft980513_1751_0800S104601L.fits 8015
3 ft980513_1751_0800S104701L.fits 8015
3 ft980513_1751_0800S104801L.fits 8015
4 ft980513_1751_0800S103901H.fits 5436
4 ft980513_1751_0800S104001H.fits 5436
5 ft980513_1751_0800S102101M.fits 71
5 ft980513_1751_0800S102501M.fits 71
5 ft980513_1751_0800S104301M.fits 71
6 ft980513_1751_0800S104101M.fits 64
7 ft980513_1751_0800S100701L.fits 56
8 ft980513_1751_0800S103101H.fits 15
-> Creating ad26032000s100101h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  10  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 10 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S101401H.fits 
 2 -- ft980513_1751_0800S101901H.fits 
 3 -- ft980513_1751_0800S102301H.fits 
 4 -- ft980513_1751_0800S102701H.fits 
 5 -- ft980513_1751_0800S102901H.fits 
 6 -- ft980513_1751_0800S103001H.fits 
 7 -- ft980513_1751_0800S103401H.fits 
 8 -- ft980513_1751_0800S103501H.fits 
 9 -- ft980513_1751_0800S103801H.fits 
 10 -- ft980513_1751_0800S104501H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S101401H.fits 
 2 -- ft980513_1751_0800S101901H.fits 
 3 -- ft980513_1751_0800S102301H.fits 
 4 -- ft980513_1751_0800S102701H.fits 
 5 -- ft980513_1751_0800S102901H.fits 
 6 -- ft980513_1751_0800S103001H.fits 
 7 -- ft980513_1751_0800S103401H.fits 
 8 -- ft980513_1751_0800S103501H.fits 
 9 -- ft980513_1751_0800S103801H.fits 
 10 -- ft980513_1751_0800S104501H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s100201m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  17  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 17 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S100101M.fits 
 2 -- ft980513_1751_0800S100301M.fits 
 3 -- ft980513_1751_0800S100501M.fits 
 4 -- ft980513_1751_0800S100901M.fits 
 5 -- ft980513_1751_0800S101301M.fits 
 6 -- ft980513_1751_0800S101501M.fits 
 7 -- ft980513_1751_0800S101801M.fits 
 8 -- ft980513_1751_0800S102001M.fits 
 9 -- ft980513_1751_0800S102201M.fits 
 10 -- ft980513_1751_0800S102401M.fits 
 11 -- ft980513_1751_0800S102601M.fits 
 12 -- ft980513_1751_0800S102801M.fits 
 13 -- ft980513_1751_0800S103301M.fits 
 14 -- ft980513_1751_0800S103601M.fits 
 15 -- ft980513_1751_0800S103701M.fits 
 16 -- ft980513_1751_0800S104201M.fits 
 17 -- ft980513_1751_0800S104901M.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S100101M.fits 
 2 -- ft980513_1751_0800S100301M.fits 
 3 -- ft980513_1751_0800S100501M.fits 
 4 -- ft980513_1751_0800S100901M.fits 
 5 -- ft980513_1751_0800S101301M.fits 
 6 -- ft980513_1751_0800S101501M.fits 
 7 -- ft980513_1751_0800S101801M.fits 
 8 -- ft980513_1751_0800S102001M.fits 
 9 -- ft980513_1751_0800S102201M.fits 
 10 -- ft980513_1751_0800S102401M.fits 
 11 -- ft980513_1751_0800S102601M.fits 
 12 -- ft980513_1751_0800S102801M.fits 
 13 -- ft980513_1751_0800S103301M.fits 
 14 -- ft980513_1751_0800S103601M.fits 
 15 -- ft980513_1751_0800S103701M.fits 
 16 -- ft980513_1751_0800S104201M.fits 
 17 -- ft980513_1751_0800S104901M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s100301l.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  9  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 9 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S100201L.fits 
 2 -- ft980513_1751_0800S100601L.fits 
 3 -- ft980513_1751_0800S100801L.fits 
 4 -- ft980513_1751_0800S101001L.fits 
 5 -- ft980513_1751_0800S101201L.fits 
 6 -- ft980513_1751_0800S101601L.fits 
 7 -- ft980513_1751_0800S104601L.fits 
 8 -- ft980513_1751_0800S104701L.fits 
 9 -- ft980513_1751_0800S104801L.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S100201L.fits 
 2 -- ft980513_1751_0800S100601L.fits 
 3 -- ft980513_1751_0800S100801L.fits 
 4 -- ft980513_1751_0800S101001L.fits 
 5 -- ft980513_1751_0800S101201L.fits 
 6 -- ft980513_1751_0800S101601L.fits 
 7 -- ft980513_1751_0800S104601L.fits 
 8 -- ft980513_1751_0800S104701L.fits 
 9 -- ft980513_1751_0800S104801L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000s100401h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 2 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800S103901H.fits 
 2 -- ft980513_1751_0800S104001H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800S103901H.fits 
 2 -- ft980513_1751_0800S104001H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 71 events ft980513_1751_0800S102101M.fits ft980513_1751_0800S102501M.fits ft980513_1751_0800S104301M.fits
-> Ignoring the following files containing 64 events ft980513_1751_0800S104101M.fits
-> Ignoring the following files containing 56 events ft980513_1751_0800S100701L.fits
-> Ignoring the following files containing 15 events ft980513_1751_0800S103101H.fits
-> Grouping g2 event files
-> stdout output from group_event_files
1 ft980513_1751_0800G202870H.fits 25180
1 ft980513_1751_0800G203870H.fits 25180
1 ft980513_1751_0800G203970H.fits 25180
1 ft980513_1751_0800G204770H.fits 25180
1 ft980513_1751_0800G204870H.fits 25180
1 ft980513_1751_0800G205670H.fits 25180
1 ft980513_1751_0800G205870H.fits 25180
1 ft980513_1751_0800G206070H.fits 25180
1 ft980513_1751_0800G206870H.fits 25180
1 ft980513_1751_0800G207070H.fits 25180
1 ft980513_1751_0800G207870H.fits 25180
1 ft980513_1751_0800G207970H.fits 25180
1 ft980513_1751_0800G208170H.fits 25180
1 ft980513_1751_0800G208970H.fits 25180
2 ft980513_1751_0800G200870M.fits 20914
2 ft980513_1751_0800G201670M.fits 20914
2 ft980513_1751_0800G202470M.fits 20914
2 ft980513_1751_0800G203070M.fits 20914
2 ft980513_1751_0800G203770M.fits 20914
2 ft980513_1751_0800G205970M.fits 20914
2 ft980513_1751_0800G208070M.fits 20914
2 ft980513_1751_0800G209470M.fits 20914
2 ft980513_1751_0800G209770M.fits 20914
3 ft980513_1751_0800G200470L.fits 3128
3 ft980513_1751_0800G200970L.fits 3128
3 ft980513_1751_0800G201770L.fits 3128
3 ft980513_1751_0800G203270L.fits 3128
3 ft980513_1751_0800G209070L.fits 3128
4 ft980513_1751_0800G203170L.fits 328
5 ft980513_1751_0800G200770M.fits 110
5 ft980513_1751_0800G202970M.fits 110
5 ft980513_1751_0800G209370M.fits 110
6 ft980513_1751_0800G200670M.fits 40
7 ft980513_1751_0800G200570M.fits 33
8 ft980513_1751_0800G209270M.fits 28
9 ft980513_1751_0800G200370L.fits 20
10 ft980513_1751_0800G201570M.fits 19
10 ft980513_1751_0800G202370M.fits 19
10 ft980513_1751_0800G203670M.fits 19
11 ft980513_1751_0800G209170M.fits 18
12 ft980513_1751_0800G209670M.fits 17
13 ft980513_1751_0800G203370L.fits 14
14 ft980513_1751_0800G207770H.fits 11
15 ft980513_1751_0800G204570H.fits 7
15 ft980513_1751_0800G205470H.fits 7
15 ft980513_1751_0800G206670H.fits 7
15 ft980513_1751_0800G208770H.fits 7
16 ft980513_1751_0800G204670H.fits 6
16 ft980513_1751_0800G205570H.fits 6
16 ft980513_1751_0800G206770H.fits 6
16 ft980513_1751_0800G208870H.fits 6
17 ft980513_1751_0800G202770H.fits 4
18 ft980513_1751_0800G205770H.fits 4
19 ft980513_1751_0800G206970H.fits 4
20 ft980513_1751_0800G202670H.fits 2
21 ft980513_1751_0800G202570H.fits 1
22 ft980513_1751_0800G204970H.fits 1
23 ft980513_1751_0800G207670H.fits 1
-> Creating ad26032000g200170h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  14  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 14 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G202870H.fits 
 2 -- ft980513_1751_0800G203870H.fits 
 3 -- ft980513_1751_0800G203970H.fits 
 4 -- ft980513_1751_0800G204770H.fits 
 5 -- ft980513_1751_0800G204870H.fits 
 6 -- ft980513_1751_0800G205670H.fits 
 7 -- ft980513_1751_0800G205870H.fits 
 8 -- ft980513_1751_0800G206070H.fits 
 9 -- ft980513_1751_0800G206870H.fits 
 10 -- ft980513_1751_0800G207070H.fits 
 11 -- ft980513_1751_0800G207870H.fits 
 12 -- ft980513_1751_0800G207970H.fits 
 13 -- ft980513_1751_0800G208170H.fits 
 14 -- ft980513_1751_0800G208970H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G202870H.fits 
 2 -- ft980513_1751_0800G203870H.fits 
 3 -- ft980513_1751_0800G203970H.fits 
 4 -- ft980513_1751_0800G204770H.fits 
 5 -- ft980513_1751_0800G204870H.fits 
 6 -- ft980513_1751_0800G205670H.fits 
 7 -- ft980513_1751_0800G205870H.fits 
 8 -- ft980513_1751_0800G206070H.fits 
 9 -- ft980513_1751_0800G206870H.fits 
 10 -- ft980513_1751_0800G207070H.fits 
 11 -- ft980513_1751_0800G207870H.fits 
 12 -- ft980513_1751_0800G207970H.fits 
 13 -- ft980513_1751_0800G208170H.fits 
 14 -- ft980513_1751_0800G208970H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000g200270m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  9  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 9 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G200870M.fits 
 2 -- ft980513_1751_0800G201670M.fits 
 3 -- ft980513_1751_0800G202470M.fits 
 4 -- ft980513_1751_0800G203070M.fits 
 5 -- ft980513_1751_0800G203770M.fits 
 6 -- ft980513_1751_0800G205970M.fits 
 7 -- ft980513_1751_0800G208070M.fits 
 8 -- ft980513_1751_0800G209470M.fits 
 9 -- ft980513_1751_0800G209770M.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G200870M.fits 
 2 -- ft980513_1751_0800G201670M.fits 
 3 -- ft980513_1751_0800G202470M.fits 
 4 -- ft980513_1751_0800G203070M.fits 
 5 -- ft980513_1751_0800G203770M.fits 
 6 -- ft980513_1751_0800G205970M.fits 
 7 -- ft980513_1751_0800G208070M.fits 
 8 -- ft980513_1751_0800G209470M.fits 
 9 -- ft980513_1751_0800G209770M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000g200370l.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 5 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G200470L.fits 
 2 -- ft980513_1751_0800G200970L.fits 
 3 -- ft980513_1751_0800G201770L.fits 
 4 -- ft980513_1751_0800G203270L.fits 
 5 -- ft980513_1751_0800G209070L.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G200470L.fits 
 2 -- ft980513_1751_0800G200970L.fits 
 3 -- ft980513_1751_0800G201770L.fits 
 4 -- ft980513_1751_0800G203270L.fits 
 5 -- ft980513_1751_0800G209070L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 328 events ft980513_1751_0800G203170L.fits
-> Ignoring the following files containing 110 events ft980513_1751_0800G200770M.fits ft980513_1751_0800G202970M.fits ft980513_1751_0800G209370M.fits
-> Ignoring the following files containing 40 events ft980513_1751_0800G200670M.fits
-> Ignoring the following files containing 33 events ft980513_1751_0800G200570M.fits
-> Ignoring the following files containing 28 events ft980513_1751_0800G209270M.fits
-> Ignoring the following files containing 20 events ft980513_1751_0800G200370L.fits
-> Ignoring the following files containing 19 events ft980513_1751_0800G201570M.fits ft980513_1751_0800G202370M.fits ft980513_1751_0800G203670M.fits
-> Ignoring the following files containing 18 events ft980513_1751_0800G209170M.fits
-> Ignoring the following files containing 17 events ft980513_1751_0800G209670M.fits
-> Ignoring the following files containing 14 events ft980513_1751_0800G203370L.fits
-> Ignoring the following files containing 11 events ft980513_1751_0800G207770H.fits
-> Ignoring the following files containing 7 events ft980513_1751_0800G204570H.fits ft980513_1751_0800G205470H.fits ft980513_1751_0800G206670H.fits ft980513_1751_0800G208770H.fits
-> Ignoring the following files containing 6 events ft980513_1751_0800G204670H.fits ft980513_1751_0800G205570H.fits ft980513_1751_0800G206770H.fits ft980513_1751_0800G208870H.fits
-> Ignoring the following files containing 4 events ft980513_1751_0800G202770H.fits
-> Ignoring the following files containing 4 events ft980513_1751_0800G205770H.fits
-> Ignoring the following files containing 4 events ft980513_1751_0800G206970H.fits
-> Ignoring the following files containing 2 events ft980513_1751_0800G202670H.fits
-> Ignoring the following files containing 1 events ft980513_1751_0800G202570H.fits
-> Ignoring the following files containing 1 events ft980513_1751_0800G204970H.fits
-> Ignoring the following files containing 1 events ft980513_1751_0800G207670H.fits
-> Grouping g3 event files
-> stdout output from group_event_files
1 ft980513_1751_0800G302870H.fits 24859
1 ft980513_1751_0800G303870H.fits 24859
1 ft980513_1751_0800G303970H.fits 24859
1 ft980513_1751_0800G304770H.fits 24859
1 ft980513_1751_0800G304870H.fits 24859
1 ft980513_1751_0800G305670H.fits 24859
1 ft980513_1751_0800G305870H.fits 24859
1 ft980513_1751_0800G306070H.fits 24859
1 ft980513_1751_0800G306870H.fits 24859
1 ft980513_1751_0800G307570H.fits 24859
1 ft980513_1751_0800G307670H.fits 24859
1 ft980513_1751_0800G307870H.fits 24859
1 ft980513_1751_0800G308670H.fits 24859
2 ft980513_1751_0800G300870M.fits 20901
2 ft980513_1751_0800G301670M.fits 20901
2 ft980513_1751_0800G302470M.fits 20901
2 ft980513_1751_0800G303070M.fits 20901
2 ft980513_1751_0800G303770M.fits 20901
2 ft980513_1751_0800G305970M.fits 20901
2 ft980513_1751_0800G307770M.fits 20901
2 ft980513_1751_0800G309170M.fits 20901
2 ft980513_1751_0800G309470M.fits 20901
3 ft980513_1751_0800G300470L.fits 3184
3 ft980513_1751_0800G300970L.fits 3184
3 ft980513_1751_0800G301770L.fits 3184
3 ft980513_1751_0800G303270L.fits 3184
3 ft980513_1751_0800G308770L.fits 3184
4 ft980513_1751_0800G303170L.fits 299
5 ft980513_1751_0800G300770M.fits 107
5 ft980513_1751_0800G302970M.fits 107
5 ft980513_1751_0800G309070M.fits 107
6 ft980513_1751_0800G300670M.fits 39
7 ft980513_1751_0800G300570M.fits 28
8 ft980513_1751_0800G300370L.fits 26
9 ft980513_1751_0800G308970M.fits 21
10 ft980513_1751_0800G309370M.fits 20
11 ft980513_1751_0800G308870M.fits 19
12 ft980513_1751_0800G301570M.fits 18
12 ft980513_1751_0800G302370M.fits 18
12 ft980513_1751_0800G303670M.fits 18
13 ft980513_1751_0800G303370L.fits 15
14 ft980513_1751_0800G304670H.fits 11
14 ft980513_1751_0800G305570H.fits 11
14 ft980513_1751_0800G306770H.fits 11
14 ft980513_1751_0800G308570H.fits 11
15 ft980513_1751_0800G305370H.fits 7
15 ft980513_1751_0800G306570H.fits 7
15 ft980513_1751_0800G308370H.fits 7
16 ft980513_1751_0800G307470H.fits 5
17 ft980513_1751_0800G306970H.fits 4
18 ft980513_1751_0800G302570H.fits 3
19 ft980513_1751_0800G302670H.fits 2
20 ft980513_1751_0800G304070H.fits 2
21 ft980513_1751_0800G305770H.fits 2
22 ft980513_1751_0800G306670H.fits 2
23 ft980513_1751_0800G307070H.fits 1
-> Creating ad26032000g300170h.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  13  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 13 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G302870H.fits 
 2 -- ft980513_1751_0800G303870H.fits 
 3 -- ft980513_1751_0800G303970H.fits 
 4 -- ft980513_1751_0800G304770H.fits 
 5 -- ft980513_1751_0800G304870H.fits 
 6 -- ft980513_1751_0800G305670H.fits 
 7 -- ft980513_1751_0800G305870H.fits 
 8 -- ft980513_1751_0800G306070H.fits 
 9 -- ft980513_1751_0800G306870H.fits 
 10 -- ft980513_1751_0800G307570H.fits 
 11 -- ft980513_1751_0800G307670H.fits 
 12 -- ft980513_1751_0800G307870H.fits 
 13 -- ft980513_1751_0800G308670H.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G302870H.fits 
 2 -- ft980513_1751_0800G303870H.fits 
 3 -- ft980513_1751_0800G303970H.fits 
 4 -- ft980513_1751_0800G304770H.fits 
 5 -- ft980513_1751_0800G304870H.fits 
 6 -- ft980513_1751_0800G305670H.fits 
 7 -- ft980513_1751_0800G305870H.fits 
 8 -- ft980513_1751_0800G306070H.fits 
 9 -- ft980513_1751_0800G306870H.fits 
 10 -- ft980513_1751_0800G307570H.fits 
 11 -- ft980513_1751_0800G307670H.fits 
 12 -- ft980513_1751_0800G307870H.fits 
 13 -- ft980513_1751_0800G308670H.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000g300270m.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  9  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 9 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G300870M.fits 
 2 -- ft980513_1751_0800G301670M.fits 
 3 -- ft980513_1751_0800G302470M.fits 
 4 -- ft980513_1751_0800G303070M.fits 
 5 -- ft980513_1751_0800G303770M.fits 
 6 -- ft980513_1751_0800G305970M.fits 
 7 -- ft980513_1751_0800G307770M.fits 
 8 -- ft980513_1751_0800G309170M.fits 
 9 -- ft980513_1751_0800G309470M.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G300870M.fits 
 2 -- ft980513_1751_0800G301670M.fits 
 3 -- ft980513_1751_0800G302470M.fits 
 4 -- ft980513_1751_0800G303070M.fits 
 5 -- ft980513_1751_0800G303770M.fits 
 6 -- ft980513_1751_0800G305970M.fits 
 7 -- ft980513_1751_0800G307770M.fits 
 8 -- ft980513_1751_0800G309170M.fits 
 9 -- ft980513_1751_0800G309470M.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Creating ad26032000g300370l.unf
-> stdout output from cmerge
---- cmerge:  version 1.7 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking input fits files (zero TIME, GTI) ...
Checking GTI overlap in input files ... 
Merging 5 good fits files ...
Merging binary extension #: 1 
 1 -- ft980513_1751_0800G300470L.fits 
 2 -- ft980513_1751_0800G300970L.fits 
 3 -- ft980513_1751_0800G301770L.fits 
 4 -- ft980513_1751_0800G303270L.fits 
 5 -- ft980513_1751_0800G308770L.fits 
Merging binary extension #: 2 
 1 -- ft980513_1751_0800G300470L.fits 
 2 -- ft980513_1751_0800G300970L.fits 
 3 -- ft980513_1751_0800G301770L.fits 
 4 -- ft980513_1751_0800G303270L.fits 
 5 -- ft980513_1751_0800G308770L.fits 
Checking the output file ...
 Extention # 1 ...... OK
 Extention # 2 ...... OK
The program appears to have finished successfully!
-> Ignoring the following files containing 299 events ft980513_1751_0800G303170L.fits
-> Ignoring the following files containing 107 events ft980513_1751_0800G300770M.fits ft980513_1751_0800G302970M.fits ft980513_1751_0800G309070M.fits
-> Ignoring the following files containing 39 events ft980513_1751_0800G300670M.fits
-> Ignoring the following files containing 28 events ft980513_1751_0800G300570M.fits
-> Ignoring the following files containing 26 events ft980513_1751_0800G300370L.fits
-> Ignoring the following files containing 21 events ft980513_1751_0800G308970M.fits
-> Ignoring the following files containing 20 events ft980513_1751_0800G309370M.fits
-> Ignoring the following files containing 19 events ft980513_1751_0800G308870M.fits
-> Ignoring the following files containing 18 events ft980513_1751_0800G301570M.fits ft980513_1751_0800G302370M.fits ft980513_1751_0800G303670M.fits
-> Ignoring the following files containing 15 events ft980513_1751_0800G303370L.fits
-> Ignoring the following files containing 11 events ft980513_1751_0800G304670H.fits ft980513_1751_0800G305570H.fits ft980513_1751_0800G306770H.fits ft980513_1751_0800G308570H.fits
-> Ignoring the following files containing 7 events ft980513_1751_0800G305370H.fits ft980513_1751_0800G306570H.fits ft980513_1751_0800G308370H.fits
-> Ignoring the following files containing 5 events ft980513_1751_0800G307470H.fits
-> Ignoring the following files containing 4 events ft980513_1751_0800G306970H.fits
-> Ignoring the following files containing 3 events ft980513_1751_0800G302570H.fits
-> Ignoring the following files containing 2 events ft980513_1751_0800G302670H.fits
-> Ignoring the following files containing 2 events ft980513_1751_0800G304070H.fits
-> Ignoring the following files containing 2 events ft980513_1751_0800G305770H.fits
-> Ignoring the following files containing 2 events ft980513_1751_0800G306670H.fits
-> Ignoring the following files containing 1 events ft980513_1751_0800G307070H.fits
-> stdout output from tar
a ft980513_1751_0800G200370L.fits 31K
a ft980513_1751_0800G200570M.fits 31K
a ft980513_1751_0800G200670M.fits 31K
a ft980513_1751_0800G200770M.fits 31K
a ft980513_1751_0800G201570M.fits 31K
a ft980513_1751_0800G202370M.fits 31K
a ft980513_1751_0800G202570H.fits 31K
a ft980513_1751_0800G202670H.fits 31K
a ft980513_1751_0800G202770H.fits 31K
a ft980513_1751_0800G202970M.fits 31K
a ft980513_1751_0800G203170L.fits 40K
a ft980513_1751_0800G203370L.fits 31K
a ft980513_1751_0800G203670M.fits 31K
a ft980513_1751_0800G204570H.fits 31K
a ft980513_1751_0800G204670H.fits 31K
a ft980513_1751_0800G204970H.fits 31K
a ft980513_1751_0800G205470H.fits 31K
a ft980513_1751_0800G205570H.fits 31K
a ft980513_1751_0800G205770H.fits 31K
a ft980513_1751_0800G206670H.fits 31K
a ft980513_1751_0800G206770H.fits 31K
a ft980513_1751_0800G206970H.fits 31K
a ft980513_1751_0800G207670H.fits 31K
a ft980513_1751_0800G207770H.fits 31K
a ft980513_1751_0800G208770H.fits 31K
a ft980513_1751_0800G208870H.fits 31K
a ft980513_1751_0800G209170M.fits 31K
a ft980513_1751_0800G209270M.fits 31K
a ft980513_1751_0800G209370M.fits 31K
a ft980513_1751_0800G209670M.fits 31K
a ft980513_1751_0800G300370L.fits 31K
a ft980513_1751_0800G300570M.fits 31K
a ft980513_1751_0800G300670M.fits 31K
a ft980513_1751_0800G300770M.fits 31K
a ft980513_1751_0800G301570M.fits 31K
a ft980513_1751_0800G302370M.fits 31K
a ft980513_1751_0800G302570H.fits 31K
a ft980513_1751_0800G302670H.fits 31K
a ft980513_1751_0800G302970M.fits 31K
a ft980513_1751_0800G303170L.fits 40K
a ft980513_1751_0800G303370L.fits 31K
a ft980513_1751_0800G303670M.fits 31K
a ft980513_1751_0800G304070H.fits 31K
a ft980513_1751_0800G304670H.fits 31K
a ft980513_1751_0800G305370H.fits 31K
a ft980513_1751_0800G305570H.fits 31K
a ft980513_1751_0800G305770H.fits 31K
a ft980513_1751_0800G306570H.fits 31K
a ft980513_1751_0800G306670H.fits 31K
a ft980513_1751_0800G306770H.fits 31K
a ft980513_1751_0800G306970H.fits 31K
a ft980513_1751_0800G307070H.fits 31K
a ft980513_1751_0800G307470H.fits 31K
a ft980513_1751_0800G308370H.fits 31K
a ft980513_1751_0800G308570H.fits 31K
a ft980513_1751_0800G308870M.fits 31K
a ft980513_1751_0800G308970M.fits 31K
a ft980513_1751_0800G309070M.fits 31K
a ft980513_1751_0800G309370M.fits 31K
a ft980513_1751_0800S000701L.fits 29K
a ft980513_1751_0800S002101M.fits 29K
a ft980513_1751_0800S002501M.fits 29K
a ft980513_1751_0800S003201H.fits 29K
a ft980513_1751_0800S004101M.fits 29K
a ft980513_1751_0800S004602L.fits 29K
a ft980513_1751_0800S100701L.fits 29K
a ft980513_1751_0800S102101M.fits 29K
a ft980513_1751_0800S102501M.fits 29K
a ft980513_1751_0800S103101H.fits 29K
a ft980513_1751_0800S104101M.fits 29K
a ft980513_1751_0800S104301M.fits 29K

Converting FAINT mode files to BRIGHT and BRIGHT2 modes (10:38:13)

-> Split threshold for SIS0=40, and SIS1=40
-> Fetching faintdfe.tbl
-> Calculating DFE values for ad26032000s000101h.unf with zerodef=1
-> Converting ad26032000s000101h.unf to ad26032000s000112h.unf
-> Calculating DFE values for ad26032000s000101h.unf with zerodef=2
-> Converting ad26032000s000101h.unf to ad26032000s000102h.unf
-> Calculating DFE values for ad26032000s000201m.unf with zerodef=1
-> Converting ad26032000s000201m.unf to ad26032000s000212m.unf
-> Calculating DFE values for ad26032000s000201m.unf with zerodef=2
-> Converting ad26032000s000201m.unf to ad26032000s000202m.unf
-> Calculating DFE values for ad26032000s000301l.unf with zerodef=1
-> Converting ad26032000s000301l.unf to ad26032000s000312l.unf
-> Calculating DFE values for ad26032000s000301l.unf with zerodef=2
-> Converting ad26032000s000301l.unf to ad26032000s000302l.unf
-> Calculating DFE values for ad26032000s000401h.unf with zerodef=1
-> Converting ad26032000s000401h.unf to ad26032000s000412h.unf
-> Calculating DFE values for ad26032000s000401h.unf with zerodef=2
-> Converting ad26032000s000401h.unf to ad26032000s000402h.unf
-> Calculating DFE values for ad26032000s100101h.unf with zerodef=1
-> Converting ad26032000s100101h.unf to ad26032000s100112h.unf
-> Calculating DFE values for ad26032000s100101h.unf with zerodef=2
-> Converting ad26032000s100101h.unf to ad26032000s100102h.unf
-> Calculating DFE values for ad26032000s100201m.unf with zerodef=1
-> Converting ad26032000s100201m.unf to ad26032000s100212m.unf
-> Calculating DFE values for ad26032000s100201m.unf with zerodef=2
-> Converting ad26032000s100201m.unf to ad26032000s100202m.unf
-> Calculating DFE values for ad26032000s100301l.unf with zerodef=1
-> Converting ad26032000s100301l.unf to ad26032000s100312l.unf
-> Calculating DFE values for ad26032000s100301l.unf with zerodef=2
-> Converting ad26032000s100301l.unf to ad26032000s100302l.unf
-> Calculating DFE values for ad26032000s100401h.unf with zerodef=1
-> Converting ad26032000s100401h.unf to ad26032000s100412h.unf
-> Calculating DFE values for ad26032000s100401h.unf with zerodef=2
-> Converting ad26032000s100401h.unf to ad26032000s100402h.unf

Calibrating the unfiltered event files (10:43:34)

-> Creating GIS gain history files
-> leapsec.fits is already present in the working directory
-> Fetching gis_temp2gain.fits from /aps/calibration
-> Creating Gain History File ft980513_1751_0800.ghf
-> stdout output from temp2gain
temp2gain V4.6
leapsec FITS data was successfully read

'ft980513_1751.0800' is successfully opened
Data Start Time is 169235502.26 (19980513 175138)
Time Margin 2.0 sec included
Sync error detected in 6290 th SF
Sync error detected in 10734 th SF
Sync error detected in 11158 th SF
'ft980513_1751.0800' EOF detected, sf=11470
Data End Time is 169286434.09 (19980514 080030)
Gain History is written in ft980513_1751_0800.ghf
-> Generating attitude correction table ad26032000_004_bp4.txt
-> Extracting info from ft980513_1751_0800CMHK.fits
-> Using BP4 between 89.6906709377967 and 98.5651430156913
-> Running ascalin on all unfiltered event files
-> Preparing to run ascalin on ad26032000g200170h.unf
-> Fetching gis2_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad26032000g200170h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000g200270m.unf
-> gis2_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad26032000g200270m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000g200370l.unf
-> gis2_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad26032000g200370l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000g300170h.unf
-> Fetching gis3_ano_on_flf_180295.fits from /aps/calibration
-> Running ascalin on ad26032000g300170h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000g300270m.unf
-> gis3_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad26032000g300270m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000g300370l.unf
-> gis3_ano_on_flf_180295.fits is already present in the working directory
-> Running ascalin on ad26032000g300370l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000101h.unf
-> Fetching s0_teldef_ascalin.fits from /aps/calibration
-> Fetching sisph2pi_110397.fits from /aps/calibration
-> Running ascalin on ad26032000s000101h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s000102h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000102h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s000112h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000112h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s000201m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000201m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000202m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000202m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000212m.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000212m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000301l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000301l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000302l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000302l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000312l.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000312l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s000401h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000401h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s000402h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000402h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s000412h.unf
-> s0_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s000412h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100101h.unf
-> Fetching s1_teldef_ascalin.fits from /aps/calibration
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100101h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100102h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100102h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100112h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100112h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100201m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100201m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100202m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100202m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100212m.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100212m.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100301l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100301l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100302l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100302l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100312l.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100312l.unf
-> stdout output from ascalin
ASCALIN_V0.9v
 Detected gap > 15min in attitude file:    169280301.61181
 
Detected gap > 15min in attitude file:
-> Preparing to run ascalin on ad26032000s100401h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100401h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100402h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100402h.unf
-> stdout output from ascalin
ASCALIN_V0.9v
-> Preparing to run ascalin on ad26032000s100412h.unf
-> s1_teldef_ascalin.fits is already present in the working directory
-> sisph2pi_110397.fits is already present in the working directory
-> Running ascalin on ad26032000s100412h.unf
-> stdout output from ascalin
ASCALIN_V0.9v

Creating filter files (10:52:46)

-> leapsec.fits is already present in the working directory
-> Fetching rigidity.data.1.23 from /aps/calibration
-> Copying orbit file /aps/orbit/frf.orbit.251 to working directory
-> Creating ft980513_1751_0800.mkf
-> stdout output from mkfilter2
 
leapsec FITS data was successfully read

S0-HK file: ft980513_1751_0800S0HK.fits

S1-HK file: ft980513_1751_0800S1HK.fits

G2-HK file: ft980513_1751_0800G2HK.fits

G3-HK file: ft980513_1751_0800G3HK.fits

Date and time are: 1998-05-13 17:50:24  mjd=50946.743336

Orbit file name is frf.orbit.251

Epoch of Orbital Elements: 1998-05-11 06:59:59

Rigidity Data File: rigidity.data.1.23

Attitude FRF: fa980513_1751.0800

output FITS File: ft980513_1751_0800.mkf

mkfilter2: Warning, faQparam error: time= 1.692354402602e+08 outside range of attitude file

           Euler angles undefined for this bin

mkfilter2: Warning, faQparam error: time= 1.692354722602e+08 outside range of attitude file

           Euler angles undefined for this bin

Total 1594 Data bins were processed.
-> Adding deadtime to ft980513_1751_0800.mkf
-> Adding ad26032000_s0.dfe to ft980513_1751_0800.mkf
-> Adding ad26032000_s1.dfe to ft980513_1751_0800.mkf
-> Plotting quantities from ft980513_1751_0800.mkf
-> Extracting telemetry corruption files

Cleaning and filtering the unfiltered event files (11:11:40)

-> Skipping ad26032000s000101h.unf because of mode
-> Filtering ad26032000s000102h.unf into ad26032000s000102h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   6767.8621
 The mean of the selected column is                  19.447879
 The standard deviation of the selected column is    7.4821949
 The minimum of selected column is                   3.4204676
 The maximum of selected column is                   57.750195
 The number of points used in calculation is              348
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<41.8 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.18E+05    32153 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          29408     20015              0      9393         0         0
 Writing events file
  20015 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         29408     20015              0      9393         0         0
   in  11368.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        20015
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        9042
 Flickering pixels iter, pixels & cnts :   1           7          81
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :           14
 Number of (internal) image counts   :        20015
 Number of image cts rejected (N, %) :         912345.58
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           14            0            0
 
 Image counts      :             0        20015            0            0
 Image cts rejected:             0         9123            0            0
 Image cts rej (%) :          0.00        45.58         0.00         0.00
 
    filtering data...
 
 Total counts      :             0        20015            0            0
 Total cts rejected:             0         9123            0            0
 Total cts rej (%) :          0.00        45.58         0.00         0.00
 
 Number of clean counts accepted  :        10892
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           14
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad26032000s000102h.evt use_events=no
Wrote cleaned events file to ad26032000s000102h.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad26032000s000112h.unf into ad26032000s000112h.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   6767.8621
 The mean of the selected column is                  19.447879
 The standard deviation of the selected column is    7.4821949
 The minimum of selected column is                   3.4204676
 The maximum of selected column is                   57.750195
 The number of points used in calculation is              348
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<41.8 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.18E+05    32508 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000112h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          29574     20105              0      9469         0         0
 Writing events file
  20105 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         29574     20105              0      9469         0         0
   in  11368.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        20105
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        9042
 Flickering pixels iter, pixels & cnts :   1           7          81
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :           14
 Number of (internal) image counts   :        20105
 Number of image cts rejected (N, %) :         912345.38
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           14            0            0
 
 Image counts      :             0        20105            0            0
 Image cts rejected:             0         9123            0            0
 Image cts rej (%) :          0.00        45.38         0.00         0.00
 
    filtering data...
 
 Total counts      :             0        20105            0            0
 Total cts rejected:             0         9123            0            0
 Total cts rej (%) :          0.00        45.38         0.00         0.00
 
 Number of clean counts accepted  :        10982
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           14
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad26032000s000112h.evt use_events=no
Wrote cleaned events file to ad26032000s000112h.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad26032000s000201m.unf because of mode
-> Filtering ad26032000s000202m.unf into ad26032000s000202m.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4053.7320
 The mean of the selected column is                  20.577320
 The standard deviation of the selected column is    8.2817698
 The minimum of selected column is                   6.2500200
 The maximum of selected column is                   45.343899
 The number of points used in calculation is              197
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<45.4 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.16E+05    28830 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          27178     13134              0     14044         0         0
 Writing events file
  13134 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         27178     13134              0     14044         0         0
   in  6543.6     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        13134
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        6729
 Flickering pixels iter, pixels & cnts :   1          10         127
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :           17
 Number of (internal) image counts   :        13134
 Number of image cts rejected (N, %) :         685652.20
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           17            0            0
 
 Image counts      :             0        13134            0            0
 Image cts rejected:             0         6856            0            0
 Image cts rej (%) :          0.00        52.20         0.00         0.00
 
    filtering data...
 
 Total counts      :             0        13134            0            0
 Total cts rejected:             0         6856            0            0
 Total cts rej (%) :          0.00        52.20         0.00         0.00
 
 Number of clean counts accepted  :         6278
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           17
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad26032000s000202m.evt use_events=no
Wrote cleaned events file to ad26032000s000202m.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad26032000s000212m.unf into ad26032000s000212m.evt
-> Calculating statistics for S0_PIXL1
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4053.7320
 The mean of the selected column is                  20.577320
 The standard deviation of the selected column is    8.2817698
 The minimum of selected column is                   6.2500200
 The maximum of selected column is                   45.343899
 The number of points used in calculation is              197
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0 && S0_PIXL1<45.4 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.16E+05    29099 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000212m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          27346     13209              0     14137         0         0
 Writing events file
  13209 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         27346     13209              0     14137         0         0
   in  6543.6     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        13209
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        6729
 Flickering pixels iter, pixels & cnts :   1          12         133
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :           19
 Number of (internal) image counts   :        13209
 Number of image cts rejected (N, %) :         686251.95
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           19            0            0
 
 Image counts      :             0        13209            0            0
 Image cts rejected:             0         6862            0            0
 Image cts rej (%) :          0.00        51.95         0.00         0.00
 
    filtering data...
 
 Total counts      :             0        13209            0            0
 Total cts rejected:             0         6862            0            0
 Total cts rej (%) :          0.00        51.95         0.00         0.00
 
 Number of clean counts accepted  :         6347
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           19
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad26032000s000212m.evt use_events=no
Wrote cleaned events file to ad26032000s000212m.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad26032000s000301l.unf because of mode
-> Filtering ad26032000s000302l.unf into ad26032000s000302l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)  )&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      LOW         1998-05-13  17:57:44    0.40E+04     1348 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000302l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad26032000s000302l.evt use_events=no
Wrote cleaned events file to ad26032000s000302l.evt
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad26032000s000302l.evt since it contains 0 events
-> Filtering ad26032000s000312l.unf into ad26032000s000312l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)  )&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     LOW         1998-05-13  17:57:44    0.40E+04     1373 0100
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000312l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad26032000s000312l.evt use_events=no
Wrote cleaned events file to ad26032000s000312l.evt
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad26032000s000312l.evt since it contains 0 events
-> Skipping ad26032000s000401h.unf because of mode
-> Filtering ad26032000s000402h.unf into ad26032000s000402h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&(S0_PIXL3>0)  )&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-14  03:16:54    0.23E+03     3133 1001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000402h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> Filtering ad26032000s000412h.unf into ad26032000s000412h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&(S0_PIXL3>0)  )&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-14  03:16:54    0.23E+03     3171 1001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000412h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s000412h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS0-BRIGHT2 > Session saved, goodbye
-> Skipping ad26032000s100101h.unf because of mode
-> Filtering ad26032000s100102h.unf into ad26032000s100102h.evt
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   11439.970
 The mean of the selected column is                  33.063496
 The standard deviation of the selected column is    13.170645
 The minimum of selected column is                   11.552688
 The maximum of selected column is                   149.81299
 The number of points used in calculation is              346
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0 && S1_PIXL3<72.5 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.18E+05    63024 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          54280     36338              0     17942         0         0
 Writing events file
  36338 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         54280     36338              0     17942         0         0
   in  11364.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        36338
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              14       27469
 Flickering pixels iter, pixels & cnts :   1          19         350
 
 Number of pixels rejected           :           33
 Number of (internal) image counts   :        36338
 Number of image cts rejected (N, %) :        2781976.56
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           33
 
 Image counts      :             0            0            0        36338
 Image cts rejected:             0            0            0        27819
 Image cts rej (%) :          0.00         0.00         0.00        76.56
 
    filtering data...
 
 Total counts      :             0            0            0        36338
 Total cts rejected:             0            0            0        27819
 Total cts rej (%) :          0.00         0.00         0.00        76.56
 
 Number of clean counts accepted  :         8519
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           33
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad26032000s100102h.evt use_events=no
Wrote cleaned events file to ad26032000s100102h.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad26032000s100112h.unf into ad26032000s100112h.evt
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   11439.970
 The mean of the selected column is                  33.063496
 The standard deviation of the selected column is    13.170645
 The minimum of selected column is                   11.552688
 The maximum of selected column is                   149.81299
 The number of points used in calculation is              346
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0 && S1_PIXL3<72.5 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.18E+05    63293 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100112h.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          54471     36433              0     18038         0         0
 Writing events file
  36433 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         54471     36433              0     18038         0         0
   in  11364.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        36433
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              14       27479
 Flickering pixels iter, pixels & cnts :   1          19         350
 
 Number of pixels rejected           :           33
 Number of (internal) image counts   :        36433
 Number of image cts rejected (N, %) :        2782976.38
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           33
 
 Image counts      :             0            0            0        36433
 Image cts rejected:             0            0            0        27829
 Image cts rej (%) :          0.00         0.00         0.00        76.38
 
    filtering data...
 
 Total counts      :             0            0            0        36433
 Total cts rejected:             0            0            0        27829
 Total cts rej (%) :          0.00         0.00         0.00        76.38
 
 Number of clean counts accepted  :         8604
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           33
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad26032000s100112h.evt use_events=no
Wrote cleaned events file to ad26032000s100112h.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad26032000s100201m.unf because of mode
-> Filtering ad26032000s100202m.unf into ad26032000s100202m.evt
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3307.3858
 The mean of the selected column is                  28.268255
 The standard deviation of the selected column is    9.4396171
 The minimum of selected column is                   10.031281
 The maximum of selected column is                   57.593937
 The number of points used in calculation is              117
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>-0 && S1_PIXL3<56.5 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.16E+05    54939 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          48207     14180              0     34027         0         0
 Writing events file
  14180 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         48207     14180              0     34027         0         0
   in  3911.8     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        14180
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              17       11000
 Flickering pixels iter, pixels & cnts :   1          14         224
 
 Number of pixels rejected           :           31
 Number of (internal) image counts   :        14180
 Number of image cts rejected (N, %) :        1122479.15
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           31
 
 Image counts      :             0            0            0        14180
 Image cts rejected:             0            0            0        11224
 Image cts rej (%) :          0.00         0.00         0.00        79.15
 
    filtering data...
 
 Total counts      :             0            0            0        14180
 Total cts rejected:             0            0            0        11224
 Total cts rej (%) :          0.00         0.00         0.00        79.15
 
 Number of clean counts accepted  :         2956
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           31
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad26032000s100202m.evt use_events=no
Wrote cleaned events file to ad26032000s100202m.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad26032000s100212m.unf into ad26032000s100212m.evt
-> Calculating statistics for S1_PIXL3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3307.3858
 The mean of the selected column is                  28.268255
 The standard deviation of the selected column is    9.4396171
 The minimum of selected column is                   10.031281
 The maximum of selected column is                   57.593937
 The number of points used in calculation is              117
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>-0 && S1_PIXL3<56.5 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.16E+05    55118 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100212m.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          48343     14216              0     34127         0         0
 Writing events file
  14216 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         48343     14216              0     34127         0         0
   in  3911.8     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        14216
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              17       11010
 Flickering pixels iter, pixels & cnts :   1          14         224
 
 Number of pixels rejected           :           31
 Number of (internal) image counts   :        14216
 Number of image cts rejected (N, %) :        1123479.02
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           31
 
 Image counts      :             0            0            0        14216
 Image cts rejected:             0            0            0        11234
 Image cts rej (%) :          0.00         0.00         0.00        79.02
 
    filtering data...
 
 Total counts      :             0            0            0        14216
 Total cts rejected:             0            0            0        11234
 Total cts rej (%) :          0.00         0.00         0.00        79.02
 
 Number of clean counts accepted  :         2982
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           31
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad26032000s100212m.evt use_events=no
Wrote cleaned events file to ad26032000s100212m.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad26032000s100301l.unf because of mode
-> Filtering ad26032000s100302l.unf into ad26032000s100302l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0)  )&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      LOW         1998-05-13  17:57:44    0.40E+04     2907 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100302l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad26032000s100302l.evt use_events=no
Wrote cleaned events file to ad26032000s100302l.evt
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad26032000s100302l.evt since it contains 0 events
-> Filtering ad26032000s100312l.unf into ad26032000s100312l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0)  )&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     LOW         1998-05-13  17:57:44    0.40E+04     2922 0001
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100312l.unf
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data13/seq_proc/ad0_26032000.004/screen_in_event.xs
    reading data file: /data/data13/seq_proc/ad0_26032000.004/screen_out_event.x
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0 0.00
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad26032000s100312l.evt use_events=no
Wrote cleaned events file to ad26032000s100312l.evt
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad26032000s100312l.evt since it contains 0 events
-> Skipping ad26032000s100401h.unf because of mode
-> Filtering ad26032000s100402h.unf into ad26032000s100402h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>0)&&(S1_PIXL2>0)  )&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-14  04:58:14    0.22E+03     4180 0110
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100402h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> Filtering ad26032000s100412h.unf into ad26032000s100412h.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>0)&&(S1_PIXL2>0)  )&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-14  04:58:14    0.22E+03     4190 0110
Processing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100412h.unf
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000s100412h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=.
The selection criteria produced no GTI's
Failed to get mkf_exp
 XSL_SELECT: Status =   -10
screen:ASCA-SIS1-BRIGHT2 > Session saved, goodbye
-> Filtering ad26032000g200170h.unf into ad26032000g200170h.evt
-> Fetching GIS2_REGION256.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          25180     11170           8810      5200         0         0
 Writing events file
  11170 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         25180     11170           8810      5200         0         0
   in  11392.     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       11170               10642               528
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad26032000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad26032000g200270m.unf into ad26032000g200270m.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20914     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20914      6545           6935      7434         0         0
 Writing events file
   6545 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20914      6545           6935      7434         0         0
   in  7007.9     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        6545                6215               330
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g200270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad26032000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad26032000g200370l.unf into ad26032000g200370l.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3128     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200370l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
           0                   0                 0
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g200370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS2-PH > set image det
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad26032000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad26032000g200370l.evt since it contains 0 events
-> Filtering ad26032000g300170h.unf into ad26032000g300170h.evt
-> Fetching GIS3_REGION256.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          24859     11963           7221      5675         0         0
 Writing events file
  11963 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         24859     11963           7221      5675         0         0
   in  11386.     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
       11963               11403               560
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad26032000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad26032000g300270m.unf into ad26032000g300270m.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20901     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20901      7156           5702      8043         0         0
 Writing events file
   7156 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20901      7156           5702      8043         0         0
   in  7007.9     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        7156                6811               345
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g300270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad26032000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad26032000g300370l.unf into ad26032000g300370l.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3184     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300370l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
           0                   0                 0
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA > read events ad26032000g300370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!screen:ASCA-GIS3-PH > set image det
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=.
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/raid2/util2/ftools/ftools.5.0.c/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad26032000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad26032000g300370l.evt since it contains 0 events

Generating images and exposure maps (11:27:55)

-> Generating exposure map ad26032000g200170.expo
-> GIS2_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(167.5,220,24.66,28.95,245.298)
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad26032000g200170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000g200170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6589
 Mean   RA/DEC/ROLL :      305.1646      43.8846     294.6589
 Pnt    RA/DEC/ROLL :      305.1584      43.9396     294.6589
 
 Image rebin factor :             1
 Attitude Records   :         45691
 GTI intervals      :            26
 Total GTI (secs)   :     11392.357
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       2654.06      2654.06
  20 Percent Complete: Total/live time:       2654.06      2654.06
  30 Percent Complete: Total/live time:       5000.14      5000.14
  40 Percent Complete: Total/live time:       5000.14      5000.14
  50 Percent Complete: Total/live time:       7298.24      7298.24
  60 Percent Complete: Total/live time:       7298.24      7298.24
  70 Percent Complete: Total/live time:       9194.23      9194.23
  80 Percent Complete: Total/live time:       9452.36      9452.36
  90 Percent Complete: Total/live time:      10471.36     10471.36
 100 Percent Complete: Total/live time:      11392.36     11392.36
 
 Number of attitude steps  used:           13
 Number of attitude steps avail:        30036
 Mean RA/DEC pixel offset:      -11.3293      -3.3916
 
    writing expo file: ad26032000g200170.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000g200170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000g200170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642     10590             52         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10642     10590             52         0         0         0
   in  11392.     seconds
 Image            has    10590 counts for 0.9296     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642      6025             52         0         0      4565
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10642      6025             52         0         0      4565
   in  11392.     seconds
 Image            has     6025 counts for 0.5289     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642      4612             52         0         0      5978
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10642      4612             52         0         0      5978
   in  11392.     seconds
 Image            has     4612 counts for 0.4048     counts/sec
 Command not found; type ? for a command listing
!ad26032000g200170h:ASCA >
!ad26032000g200170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000g200170h:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g200170h:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g200170h:ASCA-GIS2-PH > set image sky
!ad26032000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad26032000g200170h:ASCA-GIS2-PH > extract image
!ad26032000g200170h:ASCA-GIS2-PH > save image outfile=ad26032000g200170_all.img
Wrote image to file ad26032000g200170_all.img
!ad26032000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad26032000g200170h:ASCA-GIS2-PH > extract image
!ad26032000g200170h:ASCA-GIS2-PH > save image outfile=ad26032000g200170_lo.img
Wrote image to file ad26032000g200170_lo.img
!ad26032000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad26032000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad26032000g200170h:ASCA-GIS2-PH > extract image
!ad26032000g200170h:ASCA-GIS2-PH > save image outfile=ad26032000g200170_hi.img
Wrote image to file ad26032000g200170_hi.img
!ad26032000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad26032000g200270.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad26032000g200270m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000g200270m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6593
 Mean   RA/DEC/ROLL :      305.1686      43.8831     294.6593
 Pnt    RA/DEC/ROLL :      305.1145      43.8726     294.6593
 
 Image rebin factor :             1
 Attitude Records   :         45691
 GTI intervals      :            11
 Total GTI (secs)   :      7007.909
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       1479.99      1479.99
  20 Percent Complete: Total/live time:       1479.99      1479.99
  30 Percent Complete: Total/live time:       2236.00      2236.00
  40 Percent Complete: Total/live time:       4271.99      4271.99
  50 Percent Complete: Total/live time:       4271.99      4271.99
  60 Percent Complete: Total/live time:       4560.02      4560.02
  70 Percent Complete: Total/live time:       5196.02      5196.02
  80 Percent Complete: Total/live time:       5688.02      5688.02
  90 Percent Complete: Total/live time:       6912.06      6912.06
 100 Percent Complete: Total/live time:       7007.91      7007.91
 
 Number of attitude steps  used:           33
 Number of attitude steps avail:        10188
 Mean RA/DEC pixel offset:      -14.9020      -3.9628
 
    writing expo file: ad26032000g200270.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000g200270m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      6176             39         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6215      6176             39         0         0         0
   in  7007.9     seconds
 Image            has     6176 counts for 0.8813     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      3535             39         0         0      2641
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6215      3535             39         0         0      2641
   in  7007.9     seconds
 Image            has     3535 counts for 0.5044     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      2661             39         0         0      3515
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6215      2661             39         0         0      3515
   in  7007.9     seconds
 Image            has     2661 counts for 0.3797     counts/sec
 Command not found; type ? for a command listing
!ad26032000g200270m:ASCA >
!ad26032000g200270m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000g200270m:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g200270m:ASCA > read events ad26032000g200270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g200270m:ASCA-GIS2-PH > set image sky
!ad26032000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad26032000g200270m:ASCA-GIS2-PH > extract image
!ad26032000g200270m:ASCA-GIS2-PH > save image outfile=ad26032000g200270_all.img
Wrote image to file ad26032000g200270_all.img
!ad26032000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad26032000g200270m:ASCA-GIS2-PH > extract image
!ad26032000g200270m:ASCA-GIS2-PH > save image outfile=ad26032000g200270_lo.img
Wrote image to file ad26032000g200270_lo.img
!ad26032000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad26032000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad26032000g200270m:ASCA-GIS2-PH > extract image
!ad26032000g200270m:ASCA-GIS2-PH > save image outfile=ad26032000g200270_hi.img
Wrote image to file ad26032000g200270_hi.img
!ad26032000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad26032000g300170.expo
-> GIS3_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(217,95,21.56,25.92,169.216)
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad26032000g300170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000g300170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6512
 Mean   RA/DEC/ROLL :      305.1534      43.9081     294.6512
 Pnt    RA/DEC/ROLL :      305.1696      43.9161     294.6512
 
 Image rebin factor :             1
 Attitude Records   :         45691
 GTI intervals      :            26
 Total GTI (secs)   :     11386.357
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       2654.06      2654.06
  20 Percent Complete: Total/live time:       2654.06      2654.06
  30 Percent Complete: Total/live time:       4998.14      4998.14
  40 Percent Complete: Total/live time:       4998.14      4998.14
  50 Percent Complete: Total/live time:       7294.24      7294.24
  60 Percent Complete: Total/live time:       7294.24      7294.24
  70 Percent Complete: Total/live time:       9191.73      9191.73
  80 Percent Complete: Total/live time:       9448.36      9448.36
  90 Percent Complete: Total/live time:      10467.36     10467.36
 100 Percent Complete: Total/live time:      11386.36     11386.36
 
 Number of attitude steps  used:           13
 Number of attitude steps avail:        30029
 Mean RA/DEC pixel offset:       -0.1987      -2.2478
 
    writing expo file: ad26032000g300170.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000g300170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000g300170h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403     11341             62         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11403     11341             62         0         0         0
   in  11386.     seconds
 Image            has    11341 counts for 0.9960     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403      6481             62         0         0      4860
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11403      6481             62         0         0      4860
   in  11386.     seconds
 Image            has     6481 counts for 0.5692     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403      4898             62         0         0      6443
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11403      4898             62         0         0      6443
   in  11386.     seconds
 Image            has     4898 counts for 0.4302     counts/sec
 Command not found; type ? for a command listing
!ad26032000g300170h:ASCA >
!ad26032000g300170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000g300170h:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g300170h:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g300170h:ASCA-GIS3-PH > set image sky
!ad26032000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad26032000g300170h:ASCA-GIS3-PH > extract image
!ad26032000g300170h:ASCA-GIS3-PH > save image outfile=ad26032000g300170_all.img
Wrote image to file ad26032000g300170_all.img
!ad26032000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad26032000g300170h:ASCA-GIS3-PH > extract image
!ad26032000g300170h:ASCA-GIS3-PH > save image outfile=ad26032000g300170_lo.img
Wrote image to file ad26032000g300170_lo.img
!ad26032000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad26032000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad26032000g300170h:ASCA-GIS3-PH > extract image
!ad26032000g300170h:ASCA-GIS3-PH > save image outfile=ad26032000g300170_hi.img
Wrote image to file ad26032000g300170_hi.img
!ad26032000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad26032000g300270.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad26032000g300270m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000g300270m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
 rebin gis:  1
     multiply inst map...
 
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6516
 Mean   RA/DEC/ROLL :      305.1575      43.9066     294.6516
 Pnt    RA/DEC/ROLL :      305.1257      43.8491     294.6516
 
 Image rebin factor :             1
 Attitude Records   :         45691
 GTI intervals      :            11
 Total GTI (secs)   :      7007.909
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       1479.99      1479.99
  20 Percent Complete: Total/live time:       1479.99      1479.99
  30 Percent Complete: Total/live time:       2236.00      2236.00
  40 Percent Complete: Total/live time:       4271.99      4271.99
  50 Percent Complete: Total/live time:       4271.99      4271.99
  60 Percent Complete: Total/live time:       4560.02      4560.02
  70 Percent Complete: Total/live time:       5196.02      5196.02
  80 Percent Complete: Total/live time:       5688.02      5688.02
  90 Percent Complete: Total/live time:       6912.06      6912.06
 100 Percent Complete: Total/live time:       7007.91      7007.91
 
 Number of attitude steps  used:           33
 Number of attitude steps avail:        10188
 Mean RA/DEC pixel offset:       -3.1894      -2.7993
 
    writing expo file: ad26032000g300270.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000g300270m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      6774             37         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6811      6774             37         0         0         0
   in  7007.9     seconds
 Image            has     6774 counts for 0.9666     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      3839             37         0         0      2935
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6811      3839             37         0         0      2935
   in  7007.9     seconds
 Image            has     3839 counts for 0.5478     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      2964             37         0         0      3810
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6811      2964             37         0         0      3810
   in  7007.9     seconds
 Image            has     2964 counts for 0.4230     counts/sec
 Command not found; type ? for a command listing
!ad26032000g300270m:ASCA >
!ad26032000g300270m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000g300270m:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g300270m:ASCA > read events ad26032000g300270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000g300270m:ASCA-GIS3-PH > set image sky
!ad26032000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad26032000g300270m:ASCA-GIS3-PH > extract image
!ad26032000g300270m:ASCA-GIS3-PH > save image outfile=ad26032000g300270_all.img
Wrote image to file ad26032000g300270_all.img
!ad26032000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad26032000g300270m:ASCA-GIS3-PH > extract image
!ad26032000g300270m:ASCA-GIS3-PH > save image outfile=ad26032000g300270_lo.img
Wrote image to file ad26032000g300270_lo.img
!ad26032000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad26032000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad26032000g300270m:ASCA-GIS3-PH > extract image
!ad26032000g300270m:ASCA-GIS3-PH > save image outfile=ad26032000g300270_hi.img
Wrote image to file ad26032000g300270_hi.img
!ad26032000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad26032000s000102.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad26032000s000102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000s000102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON         OFF         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6416
 Mean   RA/DEC/ROLL :      305.1400      43.8902     294.6416
 Pnt    RA/DEC/ROLL :      305.1833      43.9342     294.6416
 
 Image rebin factor :             4
 Attitude Records   :         45691
 Hot Pixels         :            14
 GTI intervals      :            27
 Total GTI (secs)   :     11367.690
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       1624.17      1624.17
  20 Percent Complete: Total/live time:       2944.17      2944.17
  30 Percent Complete: Total/live time:       4943.37      4943.37
  40 Percent Complete: Total/live time:       4943.37      4943.37
  50 Percent Complete: Total/live time:       7166.85      7166.85
  60 Percent Complete: Total/live time:       7166.85      7166.85
  70 Percent Complete: Total/live time:       9503.96      9503.96
  80 Percent Complete: Total/live time:       9503.96      9503.96
  90 Percent Complete: Total/live time:      11064.32     11064.32
 100 Percent Complete: Total/live time:      11367.69     11367.69
 
 Number of attitude steps  used:           16
 Number of attitude steps avail:        28069
 Mean RA/DEC pixel offset:      -53.6312     -92.4735
 
    writing expo file: ad26032000s000102.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000s000102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000s000102h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892     10892              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10892     10892              0         0         0         0
   in  11368.     seconds
 Image            has    10892 counts for 0.9582     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892      7481              0         0         0      3411
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10892      7481              0         0         0      3411
   in  11368.     seconds
 Image            has     7481 counts for 0.6581     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892      3424              0         0         0      7468
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10892      3424              0         0         0      7468
   in  11368.     seconds
 Image            has     3424 counts for 0.3012     counts/sec
 Command not found; type ? for a command listing
!ad26032000s000102h:ASCA >
!ad26032000s000102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000s000102h:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s000102h:ASCA > read events ad26032000s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad26032000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad26032000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000102_all.img
Wrote image to file ad26032000s000102_all.img
!ad26032000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad26032000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000102_lo.img
Wrote image to file ad26032000s000102_lo.img
!ad26032000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad26032000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad26032000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000102_hi.img
Wrote image to file ad26032000s000102_hi.img
!ad26032000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad26032000s000202.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad26032000s000202m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000s000202m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON         OFF         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6422
 Mean   RA/DEC/ROLL :      305.1458      43.8914     294.6422
 Pnt    RA/DEC/ROLL :      305.0171      43.6212     294.6422
 
 Image rebin factor :             4
 Attitude Records   :         45691
 Hot Pixels         :            17
 GTI intervals      :            41
 Total GTI (secs)   :      6543.642
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:        967.99       967.99
  20 Percent Complete: Total/live time:       1664.00      1664.00
  30 Percent Complete: Total/live time:       2343.98      2343.98
  40 Percent Complete: Total/live time:       4063.97      4063.97
  50 Percent Complete: Total/live time:       4063.97      4063.97
  60 Percent Complete: Total/live time:       4064.00      4064.00
  70 Percent Complete: Total/live time:       4779.96      4779.96
  80 Percent Complete: Total/live time:       5431.77      5431.77
  90 Percent Complete: Total/live time:       6191.64      6191.64
 100 Percent Complete: Total/live time:       6543.64      6543.64
 
 Number of attitude steps  used:           36
 Number of attitude steps avail:         9900
 Mean RA/DEC pixel offset:      -83.0840     -96.9438
 
    writing expo file: ad26032000s000202.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000s000202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000s000202m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.65E+04     6278 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      6278              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6278      6278              0         0         0         0
   in  6543.6     seconds
 Image            has     6278 counts for 0.9594     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      4336              0         0         0      1942
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6278      4336              0         0         0      1942
   in  6543.6     seconds
 Image            has     4336 counts for 0.6626     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      1946              0         0         0      4332
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6278      1946              0         0         0      4332
   in  6543.6     seconds
 Image            has     1946 counts for 0.2974     counts/sec
 Command not found; type ? for a command listing
!ad26032000s000202m:ASCA >
!ad26032000s000202m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000s000202m:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s000202m:ASCA > read events ad26032000s000202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad26032000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad26032000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000202_all.img
Wrote image to file ad26032000s000202_all.img
!ad26032000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad26032000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000202_lo.img
Wrote image to file ad26032000s000202_lo.img
!ad26032000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad26032000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad26032000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad26032000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad26032000s000202_hi.img
Wrote image to file ad26032000s000202_hi.img
!ad26032000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad26032000s100102.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad26032000s100102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000s100102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF         OFF         OFF          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6559
 Mean   RA/DEC/ROLL :      305.1601      43.8956     294.6559
 Pnt    RA/DEC/ROLL :      305.1627      43.9285     294.6559
 
 Image rebin factor :             4
 Attitude Records   :         45691
 Hot Pixels         :            33
 GTI intervals      :            22
 Total GTI (secs)   :     11363.920
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       1568.00      1568.00
  20 Percent Complete: Total/live time:       2864.19      2864.19
  30 Percent Complete: Total/live time:       4867.60      4867.60
  40 Percent Complete: Total/live time:       4867.60      4867.60
  50 Percent Complete: Total/live time:       7087.08      7087.08
  60 Percent Complete: Total/live time:       7087.08      7087.08
  70 Percent Complete: Total/live time:       9424.19      9424.19
  80 Percent Complete: Total/live time:       9424.19      9424.19
  90 Percent Complete: Total/live time:      11084.55     11084.55
 100 Percent Complete: Total/live time:      11363.92     11363.92
 
 Number of attitude steps  used:           16
 Number of attitude steps avail:        27845
 Mean RA/DEC pixel offset:      -58.1416     -25.0424
 
    writing expo file: ad26032000s100102.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000s100102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000s100102h
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      8519              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8519      8519              0         0         0         0
   in  11364.     seconds
 Image            has     8519 counts for 0.7497     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      5833              0         0         0      2686
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8519      5833              0         0         0      2686
   in  11364.     seconds
 Image            has     5833 counts for 0.5133     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      2694              0         0         0      5825
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8519      2694              0         0         0      5825
   in  11364.     seconds
 Image            has     2694 counts for 0.2371     counts/sec
 Command not found; type ? for a command listing
!ad26032000s100102h:ASCA >
!ad26032000s100102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000s100102h:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s100102h:ASCA > read events ad26032000s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad26032000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad26032000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100102_all.img
Wrote image to file ad26032000s100102_all.img
!ad26032000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad26032000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100102_lo.img
Wrote image to file ad26032000s100102_lo.img
!ad26032000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad26032000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad26032000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100102_hi.img
Wrote image to file ad26032000s100102_hi.img
!ad26032000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad26032000s100202.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad26032000s100202m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad26032000s100202m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF         OFF         OFF          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa980513_1751.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :      305.1598      43.9108     294.6565
 Mean   RA/DEC/ROLL :      305.1678      43.8998     294.6565
 Pnt    RA/DEC/ROLL :      304.9966      43.6155     294.6565
 
 Image rebin factor :             4
 Attitude Records   :         45691
 Hot Pixels         :            31
 GTI intervals      :            68
 Total GTI (secs)   :      3911.811
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:          0.00         0.00
  10 Percent Complete: Total/live time:       1024.00      1024.00
  20 Percent Complete: Total/live time:       1024.00      1024.00
  30 Percent Complete: Total/live time:       1247.98      1247.98
  40 Percent Complete: Total/live time:       2368.00      2368.00
  50 Percent Complete: Total/live time:       2368.00      2368.00
  60 Percent Complete: Total/live time:       2560.00      2560.00
  70 Percent Complete: Total/live time:       3040.00      3040.00
  80 Percent Complete: Total/live time:       3355.94      3355.94
  90 Percent Complete: Total/live time:       3623.81      3623.81
 100 Percent Complete: Total/live time:       3911.81      3911.81
 
 Number of attitude steps  used:           30
 Number of attitude steps avail:         9693
 Mean RA/DEC pixel offset:      -85.7486     -26.5579
 
    writing expo file: ad26032000s100202.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad26032000s100202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] ad26032000s100202m
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.39E+04     2956 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956      2956              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2956      2956              0         0         0         0
   in  3911.8     seconds
 Image            has     2956 counts for 0.7557     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956      2005              0         0         0       951
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2956      2005              0         0         0       951
   in  3911.8     seconds
 Image            has     2005 counts for 0.5126     counts/sec
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956       951              0         0         0      2005
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2956       951              0         0         0      2005
   in  3911.8     seconds
 Image            has      951 counts for 0.2431     counts/sec
 Command not found; type ? for a command listing
!ad26032000s100202m:ASCA >
!ad26032000s100202m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!ad26032000s100202m:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s100202m:ASCA > read events ad26032000s100202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!ad26032000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad26032000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad26032000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100202_all.img
Wrote image to file ad26032000s100202_all.img
!ad26032000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad26032000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100202_lo.img
Wrote image to file ad26032000s100202_lo.img
!ad26032000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad26032000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad26032000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad26032000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad26032000s100202_hi.img
Wrote image to file ad26032000s100202_hi.img
!ad26032000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis images
-> Exposure for ad26032000s000102.expo is 11367.690430 seconds
-> Exposure for ad26032000s000202.expo is 6543.641602 seconds
-> Exposure for ad26032000s100102.expo is 11363.918945 seconds
-> Exposure for ad26032000s100202.expo is 3911.811035 seconds
-> Summing the following images to produce ad26032000sis32002.totexpo
ad26032000s000102.expo
ad26032000s000202.expo
ad26032000s100102.expo
ad26032000s100202.expo
-> Setting EXPOSURE=33187.062012 in ad26032000sis32002.totexpo
-> Exposure for ad26032000s000102_all.img is 1.136769035729766E+04 seconds
-> ad26032000s000102_all.img has 10892 counts
-> Exposure for ad26032000s000202_all.img is 6.543641371428967E+03 seconds
-> ad26032000s000202_all.img has 6278 counts
-> Exposure for ad26032000s100102_all.img is 1.136391970118880E+04 seconds
-> ad26032000s100102_all.img has 8519 counts
-> Exposure for ad26032000s100202_all.img is 3.911810917079449E+03 seconds
-> ad26032000s100202_all.img has 2956 counts
-> Summing the following images to produce ad26032000sis32002_all.totsky
ad26032000s000102_all.img
ad26032000s000202_all.img
ad26032000s100102_all.img
ad26032000s100202_all.img
-> Setting EXPOSURE=33187.0623469949 in ad26032000sis32002_all.totsky
-> Setting TOTCTS=28645 in ad26032000sis32002_all.totsky
-> Exposure for ad26032000s000102_lo.img is 1.136769035729766E+04 seconds
-> ad26032000s000102_lo.img has 7481 counts
-> Exposure for ad26032000s000202_lo.img is 6.543641371428967E+03 seconds
-> ad26032000s000202_lo.img has 4336 counts
-> Exposure for ad26032000s100102_lo.img is 1.136391970118880E+04 seconds
-> ad26032000s100102_lo.img has 5833 counts
-> Exposure for ad26032000s100202_lo.img is 3.911810917079449E+03 seconds
-> ad26032000s100202_lo.img has 2005 counts
-> Summing the following images to produce ad26032000sis32002_lo.totsky
ad26032000s000102_lo.img
ad26032000s000202_lo.img
ad26032000s100102_lo.img
ad26032000s100202_lo.img
-> Setting EXPOSURE=33187.0623469949 in ad26032000sis32002_lo.totsky
-> Setting TOTCTS=19655 in ad26032000sis32002_lo.totsky
-> Exposure for ad26032000s000102_hi.img is 1.136769035729766E+04 seconds
-> ad26032000s000102_hi.img has 3424 counts
-> Exposure for ad26032000s000202_hi.img is 6.543641371428967E+03 seconds
-> ad26032000s000202_hi.img has 1946 counts
-> Exposure for ad26032000s100102_hi.img is 1.136391970118880E+04 seconds
-> ad26032000s100102_hi.img has 2694 counts
-> Exposure for ad26032000s100202_hi.img is 3.911810917079449E+03 seconds
-> ad26032000s100202_hi.img has 951 counts
-> Summing the following images to produce ad26032000sis32002_hi.totsky
ad26032000s000102_hi.img
ad26032000s000202_hi.img
ad26032000s100102_hi.img
ad26032000s100202_hi.img
-> Setting EXPOSURE=33187.0623469949 in ad26032000sis32002_hi.totsky
-> Setting TOTCTS=9015 in ad26032000sis32002_hi.totsky
-> Running XIMAGE to create ad26032000sis32002.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   21
![1]XIMAGE> read/fits ad26032000sis32002_all.totsky
 Telescope ASCA SIS0,SIS1
 Image size = 320 x 320 pixels
 Image rebin = 4
 Image center = 640.5, 640.5
 Reading an image
  Image level, min = 0.0000000 max = 90.000000
 Saving current map
![2]XIMAGE> read/expo ad26032000sis32002.totexpo
 Telescope ASCA SIS0,SIS1
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 553.11774
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.15912
  Scaling factor :     1.00000
  Min and max :   0  66
 Max-preserving scaling factor :     1.3636364
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     66.0000
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit
-> Summing gis images
-> Exposure for ad26032000g200170.expo is 11392.357422 seconds
-> Exposure for ad26032000g200270.expo is 7007.908691 seconds
-> Exposure for ad26032000g300170.expo is 11386.357422 seconds
-> Exposure for ad26032000g300270.expo is 7007.908691 seconds
-> Summing the following images to produce ad26032000gis25670.totexpo
ad26032000g200170.expo
ad26032000g200270.expo
ad26032000g300170.expo
ad26032000g300270.expo
-> Setting EXPOSURE=36794.532226 in ad26032000gis25670.totexpo
-> Exposure for ad26032000g200170_all.img is 1.139235668039322E+04 seconds
-> ad26032000g200170_all.img has 10590 counts
-> Exposure for ad26032000g200270_all.img is 7.007908992588520E+03 seconds
-> ad26032000g200270_all.img has 6176 counts
-> Exposure for ad26032000g300170_all.img is 1.138635670086741E+04 seconds
-> ad26032000g300170_all.img has 11341 counts
-> Exposure for ad26032000g300270_all.img is 7.007908992588520E+03 seconds
-> ad26032000g300270_all.img has 6774 counts
-> Summing the following images to produce ad26032000gis25670_all.totsky
ad26032000g200170_all.img
ad26032000g200270_all.img
ad26032000g300170_all.img
ad26032000g300270_all.img
-> Setting EXPOSURE=36794.5313664376 in ad26032000gis25670_all.totsky
-> Setting TOTCTS=34881 in ad26032000gis25670_all.totsky
-> Exposure for ad26032000g200170_lo.img is 1.139235668039322E+04 seconds
-> ad26032000g200170_lo.img has 6025 counts
-> Exposure for ad26032000g200270_lo.img is 7.007908992588520E+03 seconds
-> ad26032000g200270_lo.img has 3535 counts
-> Exposure for ad26032000g300170_lo.img is 1.138635670086741E+04 seconds
-> ad26032000g300170_lo.img has 6481 counts
-> Exposure for ad26032000g300270_lo.img is 7.007908992588520E+03 seconds
-> ad26032000g300270_lo.img has 3839 counts
-> Summing the following images to produce ad26032000gis25670_lo.totsky
ad26032000g200170_lo.img
ad26032000g200270_lo.img
ad26032000g300170_lo.img
ad26032000g300270_lo.img
-> Setting EXPOSURE=36794.5313664376 in ad26032000gis25670_lo.totsky
-> Setting TOTCTS=19880 in ad26032000gis25670_lo.totsky
-> Exposure for ad26032000g200170_hi.img is 1.139235668039322E+04 seconds
-> ad26032000g200170_hi.img has 4612 counts
-> Exposure for ad26032000g200270_hi.img is 7.007908992588520E+03 seconds
-> ad26032000g200270_hi.img has 2661 counts
-> Exposure for ad26032000g300170_hi.img is 1.138635670086741E+04 seconds
-> ad26032000g300170_hi.img has 4898 counts
-> Exposure for ad26032000g300270_hi.img is 7.007908992588520E+03 seconds
-> ad26032000g300270_hi.img has 2964 counts
-> Summing the following images to produce ad26032000gis25670_hi.totsky
ad26032000g200170_hi.img
ad26032000g200270_hi.img
ad26032000g300170_hi.img
ad26032000g300270_hi.img
-> Setting EXPOSURE=36794.5313664376 in ad26032000gis25670_hi.totsky
-> Setting TOTCTS=15135 in ad26032000gis25670_hi.totsky
-> Running XIMAGE to create ad26032000gis25670.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   21
![1]XIMAGE> read/fits ad26032000gis25670_all.totsky
 Telescope ASCA GIS2,GIS3
 Image size = 256 x 256 pixels
 Image rebin = 1
 Image center = 128.5, 128.5
 Reading an image
  Image level, min = 0.0000000 max = 154.00000
 Saving current map
![2]XIMAGE> read/expo ad26032000gis25670.totexpo
 Telescope ASCA GIS2,GIS3
WARNING:  assuming DRPIX based on mission info
 Reading an image
  Image level, min = 0.0000000 max = 613.24219
![3]XIMAGE> smooth
 Sigma (arcmin) :    0.36837
  Scaling factor :     1.00000
  Min and max :   0  112
 Max-preserving scaling factor :     1.3750000
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 The image is exposure corrected
 Displaying image
  Min =  0. Max =     112.000
![7]XIMAGE> grid
![8]XIMAGE> scale
![9]XIMAGE> exit

Detecting sources in summed images (11:42:54)

-> Smoothing ad26032000gis25670_all.totsky with ad26032000gis25670.totexpo
-> Clipping exposures below 5519.1798339 seconds
-> Detecting sources in ad26032000gis25670_all.smooth
-> Standard Output From STOOL ascasource:
138 114 0.00311037 59 8 228.504
80 151 0.000100015 9 10 6.912
-> Smoothing ad26032000gis25670_hi.totsky with ad26032000gis25670.totexpo
-> Clipping exposures below 5519.1798339 seconds
-> Detecting sources in ad26032000gis25670_hi.smooth
-> Standard Output From STOOL ascasource:
138 114 0.00140419 50 7 211.183
80 151 8.58823e-05 18 11 13.1126
-> Smoothing ad26032000gis25670_lo.totsky with ad26032000gis25670.totexpo
-> Clipping exposures below 5519.1798339 seconds
-> Detecting sources in ad26032000gis25670_lo.smooth
-> Standard Output From STOOL ascasource:
138 114 0.00172127 111 8 222.294
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
138 114 24 F
80 151 9 F
-> Sources with radius >= 2
138 114 24 F
80 151 9 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad26032000gis25670.src
-> Smoothing ad26032000sis32002_all.totsky with ad26032000sis32002.totexpo
-> Clipping exposures below 4978.0593018 seconds
-> Detecting sources in ad26032000sis32002_all.smooth
-> Standard Output From STOOL ascasource:
180 124 0.00200212 102 10 289.781
-> Smoothing ad26032000sis32002_hi.totsky with ad26032000sis32002.totexpo
-> Clipping exposures below 4978.0593018 seconds
-> Detecting sources in ad26032000sis32002_hi.smooth
-> Standard Output From STOOL ascasource:
179 126 0.000736566 105 10 272.05
-> Smoothing ad26032000sis32002_lo.totsky with ad26032000sis32002.totexpo
-> Clipping exposures below 4978.0593018 seconds
-> Detecting sources in ad26032000sis32002_lo.smooth
-> Standard Output From STOOL ascasource:
180 126 0.00129569 104 11 314.915
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
180 124 38 F
-> Sources with radius >= 2
180 124 38 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad26032000sis32002.src
-> Generating region files
-> Converting (720.0,496.0,2.0) to s0 detector coordinates
-> Using events in: ad26032000s000102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   15416.000
 The mean of the selected column is                  513.86667
 The standard deviation of the selected column is    5.1577416
 The minimum of selected column is                   498.00000
 The maximum of selected column is                   522.00000
 The number of points used in calculation is               30
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   13795.000
 The mean of the selected column is                  459.83333
 The standard deviation of the selected column is    5.9194789
 The minimum of selected column is                   451.00000
 The maximum of selected column is                   472.00000
 The number of points used in calculation is               30
-> Converting (720.0,496.0,2.0) to s1 detector coordinates
-> Using events in: ad26032000s100102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   10268.000
 The mean of the selected column is                  513.40000
 The standard deviation of the selected column is    5.3744033
 The minimum of selected column is                   503.00000
 The maximum of selected column is                   520.00000
 The number of points used in calculation is               20
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9950.0000
 The mean of the selected column is                  497.50000
 The standard deviation of the selected column is    6.8939333
 The minimum of selected column is                   487.00000
 The maximum of selected column is                   509.00000
 The number of points used in calculation is               20
-> Converting (138.0,114.0,2.0) to g2 detector coordinates
-> Using events in: ad26032000g200170h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   56472.000
 The mean of the selected column is                  112.94400
 The standard deviation of the selected column is    1.2214122
 The minimum of selected column is                   110.00000
 The maximum of selected column is                   116.00000
 The number of points used in calculation is              500
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   56284.000
 The mean of the selected column is                  112.56800
 The standard deviation of the selected column is    1.1967625
 The minimum of selected column is                   110.00000
 The maximum of selected column is                   116.00000
 The number of points used in calculation is              500
-> Converting (80.0,151.0,2.0) to g2 detector coordinates
-> Using events in: ad26032000g200170h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1593.0000
 The mean of the selected column is                  122.53846
 The standard deviation of the selected column is   0.77625003
 The minimum of selected column is                   121.00000
 The maximum of selected column is                   124.00000
 The number of points used in calculation is               13
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2361.0000
 The mean of the selected column is                  181.61538
 The standard deviation of the selected column is    1.2608503
 The minimum of selected column is                   180.00000
 The maximum of selected column is                   183.00000
 The number of points used in calculation is               13
-> Converting (138.0,114.0,2.0) to g3 detector coordinates
-> Using events in: ad26032000g300170h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   63969.000
 The mean of the selected column is                  118.68089
 The standard deviation of the selected column is    1.2577737
 The minimum of selected column is                   115.00000
 The maximum of selected column is                   122.00000
 The number of points used in calculation is              539
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   60977.000
 The mean of the selected column is                  113.12987
 The standard deviation of the selected column is    1.2781471
 The minimum of selected column is                   110.00000
 The maximum of selected column is                   117.00000
 The number of points used in calculation is              539
-> Converting (80.0,151.0,2.0) to g3 detector coordinates
-> Using events in: ad26032000g300170h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2806.0000
 The mean of the selected column is                  127.54545
 The standard deviation of the selected column is    1.4384937
 The minimum of selected column is                   125.00000
 The maximum of selected column is                   130.00000
 The number of points used in calculation is               22
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3979.0000
 The mean of the selected column is                  180.86364
 The standard deviation of the selected column is    1.1252705
 The minimum of selected column is                   179.00000
 The maximum of selected column is                   183.00000
 The number of points used in calculation is               22

Extracting spectra and generating response matrices (11:50:7)

-> Fetching xrt_ea_v2_0.fits
-> Fetching xrt_psf_v2_0.fits
-> sisph2pi_110397.fits already present in current directory
-> Fetching sisechos_290296.fits
-> Fetching sisrddis_290296.fits
-> Standard Output From STOOL group_event_files:
1 ad26032000s000102h.evt 17170
1 ad26032000s000202m.evt 17170
-> Fetching SIS0_NOTCHIP0.1
-> Fetching SIS0_NOTCHIP2.1
-> Fetching SIS0_NOTCHIP3.1
-> Fetching SIS0_OFFCHIP.2
-> Extracting ad26032000s010102_1.pi from ad26032000s032002_1.reg and:
ad26032000s000102h.evt
ad26032000s000202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.65E+04     6278 0100
      2 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892      9834           1058         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      5660            618         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17170     15494           1676         0         0         0
   in  17911.     seconds
 Spectrum         has    15494 counts for 0.8650     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17911.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.31930E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s010102_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad26032000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT > filter region ad26032000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad26032000s010102_1.pi group=yes
Wrote spectrum to ad26032000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting BLANK keyword from ad26032000s010102_1.pi
-> Grouping ad26032000s010102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17911.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.31930E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      16  of undefined grouping (Channel quality=bad)
 ...        17 -      20  are grouped by a factor        4
 ...        21 -      22  are grouped by a factor        2
 ...        23 -      97  are single channels
 ...        98 -      99  are grouped by a factor        2
 ...       100 -     101  are single channels
 ...       102 -     107  are grouped by a factor        2
 ...       108 -     108  are single channels
 ...       109 -     110  are grouped by a factor        2
 ...       111 -     111  are single channels
 ...       112 -     119  are grouped by a factor        2
 ...       120 -     120  are single channels
 ...       121 -     140  are grouped by a factor        2
 ...       141 -     152  are grouped by a factor        3
 ...       153 -     154  are grouped by a factor        2
 ...       155 -     160  are grouped by a factor        3
 ...       161 -     172  are grouped by a factor        4
 ...       173 -     177  are grouped by a factor        5
 ...       178 -     183  are grouped by a factor        6
 ...       184 -     190  are grouped by a factor        7
 ...       191 -     196  are grouped by a factor        6
 ...       197 -     204  are grouped by a factor        8
 ...       205 -     226  are grouped by a factor       11
 ...       227 -     238  are grouped by a factor       12
 ...       239 -     264  are grouped by a factor       26
 ...       265 -     329  are grouped by a factor       65
 ...       330 -     511  are grouped by a factor      182
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s010102_1.pi
 ** grppha 2.9.0 completed successfully
-> Source occupies chip(s) 1
-> Fetching sis0c1p40_290296.fits
-> Generating ad26032000s010102_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data files:
  ecd = ./sis0c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.
-> Generating ad26032000s010102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   35 by   38 bins
               expanded to   35 by   38 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   49.772     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  503.00  467.00 (detector coordinates)
 Point source at   19.97   11.50 (WMAP bins wrt optical axis)
 Point source at    4.89   29.95 (... in polar coordinates)
 
 Total counts in region = 1.54640E+04
 Weighted mean angle from optical axis  =  4.803 arcmin
-> Standard Output From STOOL group_event_files:
1 ad26032000s000112h.evt 17329
1 ad26032000s000212m.evt 17329
-> SIS0_NOTCHIP0.1 already present in current directory
-> SIS0_NOTCHIP2.1 already present in current directory
-> SIS0_NOTCHIP3.1 already present in current directory
-> SIS0_OFFCHIP.2 already present in current directory
-> Extracting ad26032000s010212_1.pi from ad26032000s032002_1.reg and:
ad26032000s000112h.evt
ad26032000s000212m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05    10982 0100
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.65E+04     6347 0100
      2 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05    10982 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10982      9887           1095         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6347      5708            639         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17329     15595           1734         0         0         0
   in  17911.     seconds
 Spectrum         has    15595 counts for 0.8707     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17911.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.31930E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      31  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s010212_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > read events ad26032000s000212m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.2
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad26032000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad26032000s010212_1.pi group=yes
Wrote spectrum to ad26032000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting BLANK keyword from ad26032000s010212_1.pi
-> Grouping ad26032000s010212_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17911.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.31930E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      31  of undefined grouping (Channel quality=bad)
 ...        32 -      39  are grouped by a factor        8
 ...        40 -      43  are grouped by a factor        4
 ...        44 -      46  are grouped by a factor        3
 ...        47 -      52  are grouped by a factor        2
 ...        53 -     151  are single channels
 ...       152 -     153  are grouped by a factor        2
 ...       154 -     154  are single channels
 ...       155 -     156  are grouped by a factor        2
 ...       157 -     157  are single channels
 ...       158 -     163  are grouped by a factor        2
 ...       164 -     164  are single channels
 ...       165 -     172  are grouped by a factor        2
 ...       173 -     173  are single channels
 ...       174 -     203  are grouped by a factor        2
 ...       204 -     206  are grouped by a factor        3
 ...       207 -     212  are grouped by a factor        2
 ...       213 -     215  are grouped by a factor        3
 ...       216 -     217  are grouped by a factor        2
 ...       218 -     220  are grouped by a factor        3
 ...       221 -     222  are grouped by a factor        2
 ...       223 -     225  are grouped by a factor        3
 ...       226 -     227  are grouped by a factor        2
 ...       228 -     233  are grouped by a factor        3
 ...       234 -     235  are grouped by a factor        2
 ...       236 -     238  are grouped by a factor        3
 ...       239 -     240  are grouped by a factor        2
 ...       241 -     246  are grouped by a factor        3
 ...       247 -     250  are grouped by a factor        4
 ...       251 -     256  are grouped by a factor        3
 ...       257 -     258  are grouped by a factor        2
 ...       259 -     267  are grouped by a factor        3
 ...       268 -     283  are grouped by a factor        4
 ...       284 -     298  are grouped by a factor        5
 ...       299 -     306  are grouped by a factor        4
 ...       307 -     312  are grouped by a factor        6
 ...       313 -     317  are grouped by a factor        5
 ...       318 -     323  are grouped by a factor        6
 ...       324 -     330  are grouped by a factor        7
 ...       331 -     336  are grouped by a factor        6
 ...       337 -     343  are grouped by a factor        7
 ...       344 -     352  are grouped by a factor        9
 ...       353 -     362  are grouped by a factor       10
 ...       363 -     374  are grouped by a factor       12
 ...       375 -     389  are grouped by a factor       15
 ...       390 -     403  are grouped by a factor       14
 ...       404 -     421  are grouped by a factor       18
 ...       422 -     437  are grouped by a factor       16
 ...       438 -     456  are grouped by a factor       19
 ...       457 -     479  are grouped by a factor       23
 ...       480 -     540  are grouped by a factor       61
 ...       541 -     648  are grouped by a factor      108
 ...       649 -     935  are grouped by a factor      287
 ...       936 -    1023  are grouped by a factor       88
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s010212_1.pi
 ** grppha 2.9.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad26032000s010212_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data files:
  ecd = ./sis0c1p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.
-> Generating ad26032000s010212_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   35 by   38 bins
               expanded to   35 by   38 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   49.772     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  503.00  467.00 (detector coordinates)
 Point source at   19.97   11.50 (WMAP bins wrt optical axis)
 Point source at    4.89   29.95 (... in polar coordinates)
 
 Total counts in region = 1.55660E+04
 Weighted mean angle from optical axis  =  4.802 arcmin
-> Standard Output From STOOL group_event_files:
1 ad26032000s100102h.evt 11475
1 ad26032000s100202m.evt 11475
-> Fetching SIS1_NOTCHIP0.1
-> Fetching SIS1_NOTCHIP1.1
-> Fetching SIS1_NOTCHIP2.1
-> Fetching SIS1_OFFCHIP.2
-> Extracting ad26032000s110102_1.pi from ad26032000s132002_1.reg and:
ad26032000s100102h.evt
ad26032000s100202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.39E+04     2956 0001
      2 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      7524            995         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956      2641            315         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11475     10165           1310         0         0         0
   in  15276.     seconds
 Spectrum         has    10165 counts for 0.6654     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 15276.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.11720E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      16  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s110102_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad26032000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT > filter region ad26032000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad26032000s110102_1.pi group=yes
Wrote spectrum to ad26032000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting BLANK keyword from ad26032000s110102_1.pi
-> Grouping ad26032000s110102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 15276.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.11720E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      16  of undefined grouping (Channel quality=bad)
 ...        17 -      21  are grouped by a factor        5
 ...        22 -      25  are grouped by a factor        2
 ...        26 -      80  are single channels
 ...        81 -      84  are grouped by a factor        2
 ...        85 -      88  are single channels
 ...        89 -      94  are grouped by a factor        2
 ...        95 -      95  are single channels
 ...        96 -     121  are grouped by a factor        2
 ...       122 -     139  are grouped by a factor        3
 ...       140 -     151  are grouped by a factor        4
 ...       152 -     157  are grouped by a factor        6
 ...       158 -     177  are grouped by a factor        5
 ...       178 -     185  are grouped by a factor        8
 ...       186 -     195  are grouped by a factor       10
 ...       196 -     207  are grouped by a factor       12
 ...       208 -     222  are grouped by a factor       15
 ...       223 -     241  are grouped by a factor       19
 ...       242 -     285  are grouped by a factor       44
 ...       286 -     464  are grouped by a factor      179
 ...       465 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s110102_1.pi
 ** grppha 2.9.0 completed successfully
-> Source occupies chip(s) 3
-> Fetching sis1c3p40_290296.fits
-> Generating ad26032000s110102_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C3 Bright PI RMF
Calibration data files:
  ecd = ./sis1c3p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.
-> Generating ad26032000s110102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   35 by   36 bins
               expanded to   35 by   36 bins
 First WMAP bin is at detector pixel  360  344
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   47.443     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  503.00  491.00 (detector coordinates)
 Point source at   14.41   35.35 (WMAP bins wrt optical axis)
 Point source at    8.10   67.83 (... in polar coordinates)
 
 Total counts in region = 1.01500E+04
 Weighted mean angle from optical axis  =  7.844 arcmin
-> Standard Output From STOOL group_event_files:
1 ad26032000s100112h.evt 11586
1 ad26032000s100212m.evt 11586
-> SIS1_NOTCHIP0.1 already present in current directory
-> SIS1_NOTCHIP1.1 already present in current directory
-> SIS1_NOTCHIP2.1 already present in current directory
-> SIS1_OFFCHIP.2 already present in current directory
-> Extracting ad26032000s110212_1.pi from ad26032000s132002_1.reg and:
ad26032000s100112h.evt
ad26032000s100212m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05     8604 0001
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.39E+04     2982 0001
      2 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05     8604 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8604      7575           1029         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2982      2659            323         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11586     10234           1352         0         0         0
   in  15276.     seconds
 Spectrum         has    10234 counts for 0.6700     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 15276.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.11720E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      32  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s110212_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > read events ad26032000s100212m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.2
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad26032000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad26032000s110212_1.pi group=yes
Wrote spectrum to ad26032000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting BLANK keyword from ad26032000s110212_1.pi
-> Grouping ad26032000s110212_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 15276.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.11720E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      32  of undefined grouping (Channel quality=bad)
 ...        33 -      43  are grouped by a factor       11
 ...        44 -      47  are grouped by a factor        4
 ...        48 -      50  are grouped by a factor        3
 ...        51 -      54  are grouped by a factor        2
 ...        55 -     135  are single channels
 ...       136 -     145  are grouped by a factor        2
 ...       146 -     146  are single channels
 ...       147 -     148  are grouped by a factor        2
 ...       149 -     149  are single channels
 ...       150 -     155  are grouped by a factor        2
 ...       156 -     158  are grouped by a factor        3
 ...       159 -     160  are grouped by a factor        2
 ...       161 -     163  are grouped by a factor        3
 ...       164 -     165  are grouped by a factor        2
 ...       166 -     168  are grouped by a factor        3
 ...       169 -     172  are grouped by a factor        2
 ...       173 -     175  are grouped by a factor        3
 ...       176 -     177  are grouped by a factor        2
 ...       178 -     180  are grouped by a factor        3
 ...       181 -     184  are grouped by a factor        2
 ...       185 -     208  are grouped by a factor        3
 ...       209 -     212  are grouped by a factor        4
 ...       213 -     224  are grouped by a factor        3
 ...       225 -     236  are grouped by a factor        4
 ...       237 -     239  are grouped by a factor        3
 ...       240 -     243  are grouped by a factor        4
 ...       244 -     258  are grouped by a factor        5
 ...       259 -     264  are grouped by a factor        6
 ...       265 -     268  are grouped by a factor        4
 ...       269 -     274  are grouped by a factor        6
 ...       275 -     278  are grouped by a factor        4
 ...       279 -     285  are grouped by a factor        7
 ...       286 -     297  are grouped by a factor        6
 ...       298 -     306  are grouped by a factor        9
 ...       307 -     316  are grouped by a factor       10
 ...       317 -     332  are grouped by a factor        8
 ...       333 -     344  are grouped by a factor       12
 ...       345 -     353  are grouped by a factor        9
 ...       354 -     367  are grouped by a factor       14
 ...       368 -     383  are grouped by a factor       16
 ...       384 -     404  are grouped by a factor       21
 ...       405 -     429  are grouped by a factor       25
 ...       430 -     458  are grouped by a factor       29
 ...       459 -     494  are grouped by a factor       36
 ...       495 -     634  are grouped by a factor      140
 ...       635 -     917  are grouped by a factor      283
 ...       918 -    1023  are grouped by a factor      106
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000s110212_1.pi
 ** grppha 2.9.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad26032000s110212_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C3 Bright2 PI RMF
Calibration data files:
  ecd = ./sis1c3p40_290296.fits
  cti = ./sisph2pi_110397.fits
 echo = ./sisechos_290296.fits
  rdd = ./sisrddis_290296.fits
Please stand by...
...Done.
-> Generating ad26032000s110212_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   35 by   36 bins
               expanded to   35 by   36 bins
 First WMAP bin is at detector pixel  360  344
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   47.443     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  503.00  491.00 (detector coordinates)
 Point source at   14.41   35.35 (WMAP bins wrt optical axis)
 Point source at    8.10   67.83 (... in polar coordinates)
 
 Total counts in region = 1.02170E+04
 Weighted mean angle from optical axis  =  7.845 arcmin
-> Standard Output From STOOL group_event_files:
1 ad26032000g200170h.evt 16857
1 ad26032000g200270m.evt 16857
-> GIS2_REGION256.4 already present in current directory
-> Extracting ad26032000g210170_1.pi from ad26032000g225670_1.reg and:
ad26032000g200170h.evt
ad26032000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642      6016           4626         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      3535           2680         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         16857      9551           7306         0         0         0
   in  18400.     seconds
 Spectrum         has     9551 counts for 0.5191     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18400.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g210170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad26032000g210170_1.pi group=yes
Wrote spectrum to ad26032000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting BLANK keyword from ad26032000g210170_1.pi
-> Correcting ad26032000g210170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad26032000g210170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17958.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      26  are grouped by a factor       27
 ...        27 -      33  are grouped by a factor        7
 ...        34 -      42  are grouped by a factor        9
 ...        43 -      47  are grouped by a factor        5
 ...        48 -      53  are grouped by a factor        6
 ...        54 -      58  are grouped by a factor        5
 ...        59 -      70  are grouped by a factor        3
 ...        71 -      80  are grouped by a factor        2
 ...        81 -      82  are single channels
 ...        83 -      84  are grouped by a factor        2
 ...        85 -     136  are single channels
 ...       137 -     138  are grouped by a factor        2
 ...       139 -     141  are single channels
 ...       142 -     143  are grouped by a factor        2
 ...       144 -     159  are single channels
 ...       160 -     161  are grouped by a factor        2
 ...       162 -     173  are single channels
 ...       174 -     177  are grouped by a factor        2
 ...       178 -     178  are single channels
 ...       179 -     182  are grouped by a factor        2
 ...       183 -     183  are single channels
 ...       184 -     195  are grouped by a factor        2
 ...       196 -     198  are grouped by a factor        3
 ...       199 -     212  are grouped by a factor        2
 ...       213 -     215  are grouped by a factor        3
 ...       216 -     223  are grouped by a factor        2
 ...       224 -     253  are grouped by a factor        3
 ...       254 -     261  are grouped by a factor        4
 ...       262 -     264  are grouped by a factor        3
 ...       265 -     268  are grouped by a factor        4
 ...       269 -     271  are grouped by a factor        3
 ...       272 -     287  are grouped by a factor        4
 ...       288 -     292  are grouped by a factor        5
 ...       293 -     296  are grouped by a factor        4
 ...       297 -     301  are grouped by a factor        5
 ...       302 -     305  are grouped by a factor        4
 ...       306 -     315  are grouped by a factor        5
 ...       316 -     321  are grouped by a factor        6
 ...       322 -     326  are grouped by a factor        5
 ...       327 -     332  are grouped by a factor        6
 ...       333 -     336  are grouped by a factor        4
 ...       337 -     342  are grouped by a factor        6
 ...       343 -     363  are grouped by a factor        7
 ...       364 -     368  are grouped by a factor        5
 ...       369 -     376  are grouped by a factor        8
 ...       377 -     403  are grouped by a factor        9
 ...       404 -     411  are grouped by a factor        8
 ...       412 -     418  are grouped by a factor        7
 ...       419 -     427  are grouped by a factor        9
 ...       428 -     437  are grouped by a factor       10
 ...       438 -     459  are grouped by a factor       11
 ...       460 -     474  are grouped by a factor       15
 ...       475 -     488  are grouped by a factor       14
 ...       489 -     504  are grouped by a factor       16
 ...       505 -     524  are grouped by a factor       20
 ...       525 -     539  are grouped by a factor       15
 ...       540 -     559  are grouped by a factor       20
 ...       560 -     572  are grouped by a factor       13
 ...       573 -     599  are grouped by a factor       27
 ...       600 -     651  are grouped by a factor       52
 ...       652 -     705  are grouped by a factor       54
 ...       706 -     907  are grouped by a factor      202
 ...       908 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g210170_1.pi
 ** grppha 2.9.0 completed successfully
-> Fetching gis2v4_0.rmf
-> Fetching s2bev1.fits
-> Fetching s2gridv3.fits
-> Generating ad26032000g210170_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   48 by   48 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   50   50
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  112.50  112.50 (detector coordinates)
 Point source at   20.50   18.46 (WMAP bins wrt optical axis)
 Point source at    6.77   42.00 (... in polar coordinates)
 
 Total counts in region = 9.52900E+03
 Weighted mean angle from optical axis  =  6.746 arcmin
-> Extracting ad26032000g210170_2.pi from ad26032000g225670_2.reg and:
ad26032000g200170h.evt
ad26032000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642       152          10490         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215        86           6129         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         16857       238          16619         0         0         0
   in  18400.     seconds
 Spectrum         has      238 counts for 1.2935E-02 counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18400.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.47100E-03     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g210170_2.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad26032000g210170_2.pi group=yes
Wrote spectrum to ad26032000g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad26032000g210170_2.pi since it has 238 events
-> Standard Output From STOOL group_event_files:
1 ad26032000g300170h.evt 18214
1 ad26032000g300270m.evt 18214
-> GIS3_REGION256.4 already present in current directory
-> Extracting ad26032000g310170_1.pi from ad26032000g325670_1.reg and:
ad26032000g300170h.evt
ad26032000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403      6606           4797         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      3987           2824         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         18214     10593           7621         0         0         0
   in  18394.     seconds
 Spectrum         has    10593 counts for 0.5759     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18394.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g310170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad26032000g310170_1.pi group=yes
Wrote spectrum to ad26032000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting BLANK keyword from ad26032000g310170_1.pi
-> Correcting ad26032000g310170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad26032000g310170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 17962.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      26  are grouped by a factor       27
 ...        27 -      32  are grouped by a factor        6
 ...        33 -      37  are grouped by a factor        5
 ...        38 -      43  are grouped by a factor        6
 ...        44 -      51  are grouped by a factor        4
 ...        52 -      56  are grouped by a factor        5
 ...        57 -      60  are grouped by a factor        4
 ...        61 -      63  are grouped by a factor        3
 ...        64 -      65  are grouped by a factor        2
 ...        66 -      68  are grouped by a factor        3
 ...        69 -      80  are grouped by a factor        2
 ...        81 -      83  are single channels
 ...        84 -      85  are grouped by a factor        2
 ...        86 -     178  are single channels
 ...       179 -     180  are grouped by a factor        2
 ...       181 -     181  are single channels
 ...       182 -     187  are grouped by a factor        2
 ...       188 -     188  are single channels
 ...       189 -     190  are grouped by a factor        2
 ...       191 -     191  are single channels
 ...       192 -     203  are grouped by a factor        2
 ...       204 -     206  are grouped by a factor        3
 ...       207 -     226  are grouped by a factor        2
 ...       227 -     229  are grouped by a factor        3
 ...       230 -     235  are grouped by a factor        2
 ...       236 -     238  are grouped by a factor        3
 ...       239 -     240  are grouped by a factor        2
 ...       241 -     264  are grouped by a factor        3
 ...       265 -     268  are grouped by a factor        4
 ...       269 -     271  are grouped by a factor        3
 ...       272 -     287  are grouped by a factor        4
 ...       288 -     292  are grouped by a factor        5
 ...       293 -     296  are grouped by a factor        4
 ...       297 -     299  are grouped by a factor        3
 ...       300 -     303  are grouped by a factor        4
 ...       304 -     306  are grouped by a factor        3
 ...       307 -     316  are grouped by a factor        5
 ...       317 -     328  are grouped by a factor        4
 ...       329 -     333  are grouped by a factor        5
 ...       334 -     337  are grouped by a factor        4
 ...       338 -     349  are grouped by a factor        6
 ...       350 -     364  are grouped by a factor        5
 ...       365 -     371  are grouped by a factor        7
 ...       372 -     387  are grouped by a factor        8
 ...       388 -     393  are grouped by a factor        6
 ...       394 -     401  are grouped by a factor        8
 ...       402 -     408  are grouped by a factor        7
 ...       409 -     417  are grouped by a factor        9
 ...       418 -     447  are grouped by a factor       10
 ...       448 -     459  are grouped by a factor       12
 ...       460 -     473  are grouped by a factor       14
 ...       474 -     512  are grouped by a factor       13
 ...       513 -     527  are grouped by a factor       15
 ...       528 -     563  are grouped by a factor       18
 ...       564 -     579  are grouped by a factor       16
 ...       580 -     602  are grouped by a factor       23
 ...       603 -     650  are grouped by a factor       48
 ...       651 -     703  are grouped by a factor       53
 ...       704 -     840  are grouped by a factor      137
 ...       841 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g310170_1.pi
 ** grppha 2.9.0 completed successfully
-> Fetching gis3v4_0.rmf
-> Fetching s3bev1.fits
-> Fetching s3gridv3.fits
-> Generating ad26032000g310170_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 3.00  6 Oct 1998.
 
 Input WMAP array has size   48 by   48 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   56   50
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  118.50  112.50 (detector coordinates)
 Point source at    0.86   21.94 (WMAP bins wrt optical axis)
 Point source at    5.39   87.76 (... in polar coordinates)
 
 Total counts in region = 1.05700E+04
 Weighted mean angle from optical axis  =  5.372 arcmin
-> Extracting ad26032000g310170_2.pi from ad26032000g325670_2.reg and:
ad26032000g300170h.evt
ad26032000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403       160          11243         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811        97           6714         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         18214       257          17957         0         0         0
   in  18394.     seconds
 Spectrum         has      257 counts for 1.3972E-02 counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 18394.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.47100E-03     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g310170_2.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad26032000g310170_2.pi group=yes
Wrote spectrum to ad26032000g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad26032000g310170_2.pi since it has 257 events
-> Plotting ad26032000g210170_1_pi.ps from ad26032000g210170_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:25:14 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000g210170_1.pi;
 Net count rate (cts/s) for file   1  0.5319    +/-  5.4714E-03
   using response (RMF) file...       gis2v4_0.rmf
   using auxiliary (ARF) file...      ad26032000g210170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad26032000g310170_1_pi.ps from ad26032000g310170_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:25:27 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000g310170_1.pi;
 Net count rate (cts/s) for file   1  0.5897    +/-  5.7746E-03
   using response (RMF) file...       gis3v4_0.rmf
   using auxiliary (ARF) file...      ad26032000g310170_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad26032000s010102_1_pi.ps from ad26032000s010102_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:25:39 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000s010102_1.pi;
 Net count rate (cts/s) for file   1  0.8650    +/-  6.9526E-03
   using response (RMF) file...       ad26032000s010102_1.rmf
   using auxiliary (ARF) file...      ad26032000s010102_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad26032000s010212_1_pi.ps from ad26032000s010212_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:25:54 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000s010212_1.pi;
 Net count rate (cts/s) for file   1  0.8707    +/-  6.9786E-03
   using response (RMF) file...       ad26032000s010212_1.rmf
   using auxiliary (ARF) file...      ad26032000s010212_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad26032000s110102_1_pi.ps from ad26032000s110102_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:26:07 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000s110102_1.pi;
 Net count rate (cts/s) for file   1  0.6654    +/-  6.6160E-03
   using response (RMF) file...       ad26032000s110102_1.rmf
   using auxiliary (ARF) file...      ad26032000s110102_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Plotting ad26032000s110212_1_pi.ps from ad26032000s110212_1.pi
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:26:21 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xcm" ...


!XSPEC>   data ad26032000s110212_1.pi;
 Net count rate (cts/s) for file   1  0.6700    +/-  6.6319E-03
   using response (RMF) file...       ad26032000s110212_1.rmf
   using auxiliary (ARF) file...      ad26032000s110212_1.arf
   1 data set is in use

!XSPEC>   setplot energy;

!XSPEC>   ignore bad;

!XSPEC>   setplot com log y on;

!XSPEC>   setplot com rescale y;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit

Extracting light curves (12:26:26)

-> TIMEDEL=4.0000000000E+00 for ad26032000s000102h.evt
-> TIMEDEL=4.0000000000E+00 for ad26032000s000202m.evt
-> Minimum bin size is 4.0000000000E+00 seconds
-> Extracting events from region ad26032000s032002_1.reg
-> ... and files: ad26032000s000102h.evt ad26032000s000202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.65E+04     6278 0100
      2 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892      9838           1054         0         0         0
 Writing events file
   9838 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      5666            612         0         0         0
 Writing events file
  15504 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17170     15504           1666         0         0         0
   in  17911.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad26032000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad26032000s000002_1.lc with binsize 57.7635825453067
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  17:51:36    0.18E+05    15504 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          15504     15504              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         15504     15504              0         0         0         0
   in  17911.     seconds
 Fits light curve has    15504 counts for 0.8656     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 57.7635825453067
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad26032000s000002_1.lc
Wrote FITS light curve to file ad26032000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting ad26032000s000002_1.lc in ad26032000s000002_1_lc.ps
-> Standard Output From FTOOL lcurve:
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad26032000s000002_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ WR 140              Start Time (d) .... 10946 18:13:20.260
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10947 07:14:08.260
 No. of Rows .......          315        Bin Time (s) ......    57.76
 Right Ascension ... 3.0516E+02          Internal time sys.. Converted to TJD
 Declination ....... 4.3911E+01          Experiment ........ ASCA     SIS0
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 10946.75926227117  (days)      18:13:20:260  (h:m:s:ms)
 Expected Stop .... 10947.30148449339  (days)       7:14: 8:260  (h:m:s:ms)
 
 Minimum Newbin Time    57.763584      (s)
 for Maximum Newbin No..              812
 
 Default Newbin Time is:   91.607352    (s) (to have 1 Intv. of     512 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     91.607352      (s)
 Maximum Newbin No.               512
 
 Default Newbins per Interval are:       512
 (giving       1 Interval of       512 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       512 Newbins of       91.6074     (s)
 
     512 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start 10946 18:14: 6
     Ser.1     Avg 0.8654        Chisq  187.8       Var 0.1422E-01 Newbs.    216
               Min 0.5024          Max  1.222    expVar 0.1267E-01  Bins    315
PLT> @lightcurve.pco
!PLT> dev ad26032000s000002_1_lc.ps/ps
!PLT> LA File ad26032000s000002_1.lc
!PLT> plot
!PLT> quit
-> TIMEDEL=4.0000000000E+00 for ad26032000s100102h.evt
-> TIMEDEL=4.0000000000E+00 for ad26032000s100202m.evt
-> Minimum bin size is 4.0000000000E+00 seconds
-> Extracting events from region ad26032000s132002_1.reg
-> ... and files: ad26032000s100102h.evt ad26032000s100202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.39E+04     2956 0001
      2 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      7548            971         0         0         0
 Writing events file
   7548 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956      2646            310         0         0         0
 Writing events file
  10194 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11475     10194           1281         0         0         0
   in  15276.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad26032000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad26032000s100002_1.lc with binsize 74.9251060342763
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  17:51:36    0.15E+05    10194 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          10194     10194              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10194     10194              0         0         0         0
   in  15276.     seconds
 Fits light curve has    10194 counts for 0.6673     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 74.9251060342763
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad26032000s100002_1.lc
Wrote FITS light curve to file ad26032000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting ad26032000s100002_1.lc in ad26032000s100002_1_lc.ps
-> Standard Output From FTOOL lcurve:
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad26032000s100002_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ WR 140              Start Time (d) .... 10946 18:13:52.260
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10947 07:14:08.260
 No. of Rows .......          208        Bin Time (s) ......    74.93
 Right Ascension ... 3.0516E+02          Internal time sys.. Converted to TJD
 Declination ....... 4.3911E+01          Experiment ........ ASCA     SIS1
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 10946.75963264154  (days)      18:13:52:260  (h:m:s:ms)
 Expected Stop .... 10947.30148449339  (days)       7:14: 8:260  (h:m:s:ms)
 
 Minimum Newbin Time    74.925102      (s)
 for Maximum Newbin No..              625
 
 Default Newbin Time is:   91.544779    (s) (to have 1 Intv. of     512 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     91.544779      (s)
 Maximum Newbin No.               512
 
 Default Newbins per Interval are:       512
 (giving       1 Interval of       512 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       512 Newbins of       91.5448     (s)
 
     512 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start 10946 18:15:52
     Ser.1     Avg 0.6640        Chisq  158.3       Var 0.8749E-02 Newbs.    177
               Min 0.4659          Max  1.024    expVar 0.9634E-02  Bins    208
PLT> @lightcurve.pco
!PLT> dev ad26032000s100002_1_lc.ps/ps
!PLT> LA File ad26032000s100002_1.lc
!PLT> plot
!PLT> quit
-> TIMEDEL=6.2500000000E-02 for ad26032000g200170h.evt
-> TIMEDEL=5.0000000000E-01 for ad26032000g200270m.evt
-> Minimum bin size is 5.0000000000E-01 seconds
-> Extracting events from region ad26032000g225670_1.reg
-> ... and files: ad26032000g200170h.evt ad26032000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642      6016           4626         0         0         0
 Writing events file
   6016 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      3535           2680         0         0         0
 Writing events file
   9551 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         16857      9551           7306         0         0         0
   in  18400.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad26032000g200070_1.lc with binsize 96.3263829598039
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  18:05:04    0.18E+05     9551     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           9551      9551              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9551      9551              0         0         0         0
   in  18400.     seconds
 Fits light curve has     9551 counts for 0.5191     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set binsize 96.3263829598039
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad26032000g200070_1.lc
Wrote FITS light curve to file ad26032000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting ad26032000g200070_1.lc in ad26032000g200070_1_lc.ps
-> Standard Output From FTOOL lcurve:
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad26032000g200070_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ WR 140              Start Time (d) .... 10946 18:11:44.260
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10947 06:53:52.105
 No. of Rows .......          193        Bin Time (s) ......    96.33
 Right Ascension ... 3.0516E+02          Internal time sys.. Converted to TJD
 Declination ....... 4.3911E+01          Experiment ........ ASCA     GIS2
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 10946.75815116005  (days)      18:11:44:260  (h:m:s:ms)
 Expected Stop .... 10947.28740861874  (days)       6:53:52:105  (h:m:s:ms)
 
 Minimum Newbin Time    96.326385      (s)
 for Maximum Newbin No..              475
 
 Default Newbin Time is:   96.326385    (s) (to have 1 Intv. of     475 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     96.326385      (s)
 Maximum Newbin No.               475
 
 Default Newbins per Interval are:       475
 (giving       1 Interval of       475 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       475 Newbins of       96.3264     (s)
 
     475 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start 10946 18:12:32
     Ser.1     Avg 0.5187        Chisq  218.1       Var 0.6681E-02 Newbs.    193
               Min 0.3011          Max 0.7994    expVar 0.5707E-02  Bins    193
PLT> @lightcurve.pco
!PLT> dev ad26032000g200070_1_lc.ps/ps
!PLT> LA File ad26032000g200070_1.lc
!PLT> plot
!PLT> quit
-> Extracting events from region ad26032000g225670_2.reg
-> ... and files: ad26032000g200170h.evt ad26032000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642       152          10490         0         0         0
 Writing events file
    152 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215        86           6129         0         0         0
 Writing events file
    238 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         16857       238          16619         0         0         0
   in  18400.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> skipping ad26032000g200070_2.lc since it would have 238 events
-> TIMEDEL=6.2500000000E-02 for ad26032000g300170h.evt
-> TIMEDEL=5.0000000000E-01 for ad26032000g300270m.evt
-> Minimum bin size is 5.0000000000E-01 seconds
-> Extracting events from region ad26032000g325670_1.reg
-> ... and files: ad26032000g300170h.evt ad26032000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403      6606           4797         0         0         0
 Writing events file
   6606 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      3987           2824         0         0         0
 Writing events file
  10593 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         18214     10593           7621         0         0         0
   in  18394.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad26032000g300070_1.lc with binsize 86.8227399861037
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  18:05:04    0.18E+05    10593     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          10593     10593              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10593     10593              0         0         0         0
   in  18394.     seconds
 Fits light curve has    10593 counts for 0.5759     counts/sec
 Thresholding removed more than half the bins
 Try exposure=0.0 on the extract command in xselect
 or lcthresh=0.0 if running extractor stand-alone
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events events.tmp
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set binsize 86.8227399861037
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad26032000g300070_1.lc
Wrote FITS light curve to file ad26032000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting ad26032000g300070_1.lc in ad26032000g300070_1_lc.ps
-> Standard Output From FTOOL lcurve:
 
lcurve 1.0 (xronos5.16)
 
 Series 1 file   1:ad26032000g300070_1.lc
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ WR 140              Start Time (d) .... 10946 18:11:44.260
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10947 06:53:52.105
 No. of Rows .......          215        Bin Time (s) ......    86.82
 Right Ascension ... 3.0516E+02          Internal time sys.. Converted to TJD
 Declination ....... 4.3911E+01          Experiment ........ ASCA     GIS3
 Filter ............ NONE
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:  1- Time;  2- Y-axis;  3- Y-error;  4- Fractional exposure;
 
 File contains binned data.
 
 
 Expected Start ... 10946.75815116005  (days)      18:11:44:260  (h:m:s:ms)
 Expected Stop .... 10947.28740861874  (days)       6:53:52:105  (h:m:s:ms)
 
 Minimum Newbin Time    86.822739      (s)
 for Maximum Newbin No..              527
 
 Default Newbin Time is:   89.416982    (s) (to have 1 Intv. of     512 Newbins)
 Type INDEF to accept the default value
 
 
 Newbin Time ......     89.416982      (s)
 Maximum Newbin No.               512
 
 Default Newbins per Interval are:       512
 (giving       1 Interval of       512 Newbins)
 Type INDEF to accept the default value
 
 Maximum of       1 Intvs. with       512 Newbins of       89.4170     (s)
 
     512 analysis results per interval
 
  1% completed
  2% completed
  3% completed
  4% completed
  5% completed
  6% completed
  7% completed
  8% completed
  9% completed
 10% completed
 11% completed
 12% completed
 13% completed
 14% completed
 15% completed
 16% completed
 17% completed
 18% completed
 19% completed
 20% completed
 21% completed
 22% completed
 23% completed
 24% completed
 25% completed
 26% completed
 27% completed
 28% completed
 29% completed
 30% completed
 31% completed
 32% completed
 33% completed
 34% completed
 35% completed
 36% completed
 37% completed
 38% completed
 39% completed
 40% completed
 41% completed
 42% completed
 43% completed
 44% completed
 45% completed
 46% completed
 47% completed
 48% completed
 49% completed
 50% completed
 51% completed
 52% completed
 53% completed
 54% completed
 55% completed
 56% completed
 57% completed
 58% completed
 59% completed
 60% completed
 61% completed
 62% completed
 63% completed
 64% completed
 65% completed
 66% completed
 67% completed
 68% completed
 69% completed
 70% completed
 71% completed
 72% completed
 73% completed
 74% completed
 75% completed
 76% completed
 77% completed
 78% completed
 79% completed
 80% completed
 81% completed
 82% completed
 83% completed
 84% completed
 85% completed
 86% completed
 87% completed
 88% completed
 89% completed
 90% completed
 91% completed
 92% completed
 93% completed
 94% completed
 95% completed
 96% completed
 97% completed
 98% completed
 99% completed
100% completed
 
 Intv    1   Start 10946 18:12:28
     Ser.1     Avg 0.5773        Chisq  193.7       Var 0.6913E-02 Newbs.    208
               Min 0.3916          Max 0.8753    expVar 0.6947E-02  Bins    215
PLT> @lightcurve.pco
!PLT> dev ad26032000g300070_1_lc.ps/ps
!PLT> LA File ad26032000g300070_1.lc
!PLT> plot
!PLT> quit
-> Extracting events from region ad26032000g325670_2.reg
-> ... and files: ad26032000g300170h.evt ad26032000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403       160          11243         0         0         0
 Writing events file
    160 events written to the output file
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811        97           6714         0         0         0
 Writing events file
    257 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         18214       257          17957         0         0         0
   in  18394.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> skipping ad26032000g300070_2.lc since it would have 257 events
-> Merging GTIs from the following files:
ad26032000g200170h.evt[2]
ad26032000g200270m.evt[2]
-> Making L1 light curve of ft980513_1751_0800G2HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  27393 output records from   27419  good input G2_L1    records.
-> Making L1 light curve of ft980513_1751_0800G2HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  17289 output records from   33976  good input G2_L1    records.
-> Merging GTIs from the following files:
ad26032000g300170h.evt[2]
ad26032000g300270m.evt[2]
-> Making L1 light curve of ft980513_1751_0800G3HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  26452 output records from   26478  good input G3_L1    records.
-> Making L1 light curve of ft980513_1751_0800G3HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  17138 output records from   32990  good input G3_L1    records.

Extracting source event files (12:33:41)

-> Extracting unbinned light curve ad26032000g200170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642      6016           4626         0         0         0
 Writing events file
   6016 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10642      6016           4626         0         0         0
   in  11392.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad26032000g200170.ulc use_events=yes
Wrote events list to file ad26032000g200170.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g200170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    10642     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10642       152          10490         0         0         0
 Writing events file
    152 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10642       152          10490         0         0         0
   in  11392.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad26032000g200170.ulc use_events=yes
Wrote events list to file ad26032000g200170.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g200270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215      3535           2680         0         0         0
 Writing events file
   3535 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6215      3535           2680         0         0         0
   in  7007.9     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad26032000g200270.ulc use_events=yes
Wrote events list to file ad26032000g200270.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g200270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6215     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6215        86           6129         0         0         0
 Writing events file
     86 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6215        86           6129         0         0         0
   in  7007.9     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region ad26032000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad26032000g200270.ulc use_events=yes
Wrote events list to file ad26032000g200270.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g300170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403      6606           4797         0         0         0
 Writing events file
   6606 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11403      6606           4797         0         0         0
   in  11386.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad26032000g300170.ulc use_events=yes
Wrote events list to file ad26032000g300170.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g300170.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.11E+05    11403     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          11403       160          11243         0         0         0
 Writing events file
    160 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11403       160          11243         0         0         0
   in  11386.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad26032000g300170.ulc use_events=yes
Wrote events list to file ad26032000g300170.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g300270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811      3987           2824         0         0         0
 Writing events file
   3987 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6811      3987           2824         0         0         0
   in  7007.9     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad26032000g300270.ulc use_events=yes
Wrote events list to file ad26032000g300270.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000g300270.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.70E+04     6811     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6811        97           6714         0         0         0
 Writing events file
     97 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6811        97           6714         0         0         0
   in  7007.9     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300270m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region ad26032000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad26032000g300270.ulc use_events=yes
Wrote events list to file ad26032000g300270.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad26032000s000102.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05    10892 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10892      9838           1054         0         0         0
 Writing events file
   9838 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10892      9838           1054         0         0         0
   in  11368.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad26032000s000102.ulc use_events=yes
Wrote events list to file ad26032000s000102.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad26032000s000112.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05    10982 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          10982      9891           1091         0         0         0
 Writing events file
   9891 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10982      9891           1091         0         0         0
   in  11368.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad26032000s000112.ulc use_events=yes
Wrote events list to file ad26032000s000112.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad26032000s000202.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.65E+04     6278 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6278      5666            612         0         0         0
 Writing events file
   5666 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6278      5666            612         0         0         0
   in  6543.6     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set image det
!xsel:ASCA-SIS0-BRIGHT > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad26032000s000202.ulc use_events=yes
Wrote events list to file ad26032000s000202.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad26032000s000212.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.65E+04     6347 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           6347      5714            633         0         0         0
 Writing events file
   5714 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6347      5714            633         0         0         0
   in  6543.6     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s000212m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set image det
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad26032000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad26032000s000212.ulc use_events=yes
Wrote events list to file ad26032000s000212.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad26032000s100102.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.11E+05     8519 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8519      7548            971         0         0         0
 Writing events file
   7548 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8519      7548            971         0         0         0
   in  11364.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100102h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad26032000s100102.ulc use_events=yes
Wrote events list to file ad26032000s100102.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad26032000s100112.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.11E+05     8604 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           8604      7597           1007         0         0         0
 Writing events file
   7597 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8604      7597           1007         0         0         0
   in  11364.     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100112h.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad26032000s100112.ulc use_events=yes
Wrote events list to file ad26032000s100112.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad26032000s100202.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.39E+04     2956 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2956      2646            310         0         0         0
 Writing events file
   2646 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2956      2646            310         0         0         0
   in  3911.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100202m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set image det
!xsel:ASCA-SIS1-BRIGHT > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad26032000s100202.ulc use_events=yes
Wrote events list to file ad26032000s100202.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad26032000s100212.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.39E+04     2982 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100212m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2982      2663            319         0         0         0
 Writing events file
   2663 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2982      2663            319         0         0         0
   in  3911.8     seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000s100212m.evt
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set image det
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad26032000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad26032000s100212.ulc use_events=yes
Wrote events list to file ad26032000s100212.ulc
Changing Data directory from:
    /data/data13/seq_proc/ad0_26032000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

Extracting FRAME mode data (12:38:6)

-> Extracting FRAME mode data from ft980513_1751.0800
-> stdout output from tlmFrm
 *** tlmFrm Version 1.1 (1997-08-25) *** 
total number of superframes: 11470
frame data: 169269608.148002 ---> 169269752.147522 
     S0, C3, 2 ccd mode;  Output File = fr980513_1751.0800_s0c3m2a.fits
frame data: 169269772.147455 ---> 169269916.146975 
     S0, C0, 2 ccd mode;  Output File = fr980513_1751.0800_s0c0m2a.fits
frame data: 169269936.146909 ---> 169270080.146428 
     S0, C3, 2 ccd mode;  Output File = fr980513_1751.0800_s0c3m2b.fits
frame data: 169270100.146362 ---> 169270244.145882 
     S0, C0, 2 ccd mode;  Output File = fr980513_1751.0800_s0c0m2b.fits
frame data: 169275656.127517 ---> 169275800.127037 
     S1, C1, 2 ccd mode;  Output File = fr980513_1751.0800_s1c1m2a.fits
frame data: 169275820.12697 ---> 169275964.126489 
     S1, C2, 2 ccd mode;  Output File = fr980513_1751.0800_s1c2m2a.fits
frame data: 169275984.126423 ---> 169276128.125942 
     S1, C1, 2 ccd mode;  Output File = fr980513_1751.0800_s1c1m2b.fits
frame data: 169276148.125876 ---> 169276292.125395 
     S1, C2, 2 ccd mode;  Output File = fr980513_1751.0800_s1c2m2b.fits

Total of 8 sets of frame data are extracted.
-> Processing frame fr980513_1751.0800_s0c0m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s0c0m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 340
-> Adding keywords to fr980513_1751.0800_s0c0m2a.fits
-> Processing frame fr980513_1751.0800_s0c0m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s0c0m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 339
-> Adding keywords to fr980513_1751.0800_s0c0m2b.fits
-> Processing frame fr980513_1751.0800_s0c3m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s0c3m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 319
-> Adding keywords to fr980513_1751.0800_s0c3m2a.fits
-> Processing frame fr980513_1751.0800_s0c3m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s0c3m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 317
-> Adding keywords to fr980513_1751.0800_s0c3m2b.fits
-> Processing frame fr980513_1751.0800_s1c1m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s1c1m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 194
-> Adding keywords to fr980513_1751.0800_s1c1m2a.fits
-> Processing frame fr980513_1751.0800_s1c1m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s1c1m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 194
-> Adding keywords to fr980513_1751.0800_s1c1m2b.fits
-> Processing frame fr980513_1751.0800_s1c2m2a.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s1c2m2a.fits
Output zero level image : leveled_frame.tmp
Bias level = 185
-> Adding keywords to fr980513_1751.0800_s1c2m2a.fits
-> Processing frame fr980513_1751.0800_s1c2m2b.fits with bias adjustment 0 ADU
-> stdout output from mkPixLvl
Dark upper (ADU)        : 40
Dark lower (ADU)        : -40
Bias offset (ADU)       : 0
Input frame data        : fr980513_1751.0800_s1c2m2b.fits
Output zero level image : leveled_frame.tmp
Bias level = 185
-> Adding keywords to fr980513_1751.0800_s1c2m2b.fits
-> Extracting corner pixel histograms
-> Extracting corner pixels from ad26032000s000101h.unf
-> Calculating corner pixel GTI from ft980513_1751_0800.mkf
-> Extracting corner pixels from ad26032000s000201m.unf
-> Extracting corner pixels from ad26032000s000301l.unf
-> Extracting corner pixels from ad26032000s000401h.unf
-> Extracting corner pixels from ad26032000s100101h.unf
-> Extracting corner pixels from ad26032000s100201m.unf
-> Extracting corner pixels from ad26032000s100301l.unf
-> Extracting corner pixels from ad26032000s100401h.unf

Extracting GIS calibration source spectra (12:39:58)

-> Standard Output From STOOL group_event_files:
1 ad26032000g200170h.unf 49222
1 ad26032000g200270m.unf 49222
1 ad26032000g200370l.unf 49222
-> Fetching GIS2_CALSRC256.2
-> Extracting ad26032000g220170.cal from ad26032000g200170h.unf ad26032000g200270m.unf ad26032000g200370l.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20914     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3128     1024
      2 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20914     1024
      3 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          25180      2511          22669         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20914      1949          18965         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3128       312           2816         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         49222      4772          44450         0         0         0
   in  33562.     seconds
 Spectrum         has     4772 counts for 0.1422     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 33562.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.57970E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g220170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200270m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > read events ad26032000g200370l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS2-PH > set image det
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad26032000g220170.cal group=yes
Wrote spectrum to ad26032000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting BLANK keyword from ad26032000g220170.cal
-> gis2v4_0.rmf already present in current directory
-> Plotting ad26032000g220170_cal.ps and finding peak
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:40:37 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad26032000g220170.cal;
 Net count rate (cts/s) for file   1  0.1422    +/-  2.0602E-03
   using response (RMF) file...       gis2v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =     3.5863392E+07 using    84 PHA bins.
 Reduced chi-squared =      471886.8     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =     3.5863392E+07 using    84 PHA bins.
 Reduced chi-squared =      465758.3     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =     3.5863392E+07 using    84 PHA bins.
 Reduced chi-squared =      459787.1     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      2300.341     using    84 PHA bins.
 Reduced chi-squared =      29.11824     for     79 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   612.708     -4         0.      4.1922E-03   6.079          0.
              6.4193E-02  1.0011E-02
   214.559     -5         0.      2.1091E-03   5.956          0.
              6.8142E-02  1.5804E-02
   191.305     -6         0.      2.6173E-03   5.957          0.
              6.8906E-02  1.9610E-02
   190.437     -7         0.      2.3012E-03   5.956          0.
              6.8832E-02  1.9649E-02
   190.175     -8         0.      2.4907E-03   5.956          0.
              6.8834E-02  1.9648E-02
   190.146      0         0.      2.4799E-03   5.956          0.
              6.8828E-02  1.9721E-02
   190.137      0         0.      2.4702E-03   5.955          0.
              6.8822E-02  1.9788E-02
   177.653     -1         0.      2.1303E-03   5.958      0.2229
              7.0590E-02  1.8804E-02
   78.2291     -2         0.      1.8462E-03   5.990      0.1767
              7.8269E-02  1.4756E-02
 Number of trials exceeded - last iteration delta =    99.42
   77.3395     -3         0.      2.0152E-03   5.985      0.1678
              7.8000E-02  1.5284E-02
   77.2557     -4         0.      1.8970E-03   5.984      0.1670
              7.7877E-02  1.5415E-02
   77.2234     -5         0.      1.9754E-03   5.984      0.1669
              7.7850E-02  1.5443E-02
   77.2069     -6         0.      1.9221E-03   5.984      0.1669
              7.7845E-02  1.5449E-02
   77.1993     -7         0.      1.9579E-03   5.984      0.1669
              7.7844E-02  1.5450E-02
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 8.82E-08 | -1.00  0.00 -0.01 -0.03 -0.08
 8.12E-07 |  0.09 -0.07 -0.02 -0.10 -0.99
 2.63E-06 | -0.02 -0.07 -0.07  0.99 -0.09
 4.23E-05 |  0.01  0.84 -0.54  0.02 -0.05
 1.43E-04 | -0.01  0.53  0.84  0.09 -0.06
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               1.9579E-03 +/-  0.3208E-03
    3    3    2   gaussian/b LineE    keV        5.984     +/-  0.8410E-02
    4    4    2   gaussian/b Sigma    keV       0.1669     +/-  0.1063E-01
    5    5    2   gaussian/b norm               7.7844E-02 +/-  0.1927E-02
    6    3    3   gaussian/b LineE    keV        6.588     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       0.1751     = par   4 *   1.049
    8    6    3   gaussian/b norm               1.5450E-02 +/-  0.1226E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      77.19932     using    84 PHA bins.
 Reduced chi-squared =     0.9772065     for     79 degrees of freedom
 Null hypothesis probability = 0.536

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS2 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Calibration source ad26032000g220170.cal peaks at 5.984 +/- 0.00841 keV
-> Standard Output From STOOL group_event_files:
1 ad26032000g300170h.unf 48944
1 ad26032000g300270m.unf 48944
1 ad26032000g300370l.unf 48944
-> Fetching GIS3_CALSRC256.2
-> Extracting ad26032000g320170.cal from ad26032000g300170h.unf ad26032000g300270m.unf ad26032000g300370l.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20901     1024
      2 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3184     1024
      2 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20901     1024
      3 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          24859      2210          22649         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20901      1589          19312         0         0         0
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3184       253           2931         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         48944      4052          44892         0         0         0
   in  33556.     seconds
 Spectrum         has     4052 counts for 0.1208     counts/sec
 ... written the PHA data Extension
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    - NONE            Instrument filter in use
  EXPOSURE  - 33556.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.83360E-02     Background scaling factor
  BACKFILE  - none            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - none            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 minchan(nocom)  0
 maxchan(nocom)  1023
 numchan(nocom)  4
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -    1023  are grouped by a factor        4
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad26032000g320170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA > read events ad26032000g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300270m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > read events ad26032000g300370l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!xsel:ASCA-GIS3-PH > set image det
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad26032000g320170.cal group=yes
Wrote spectrum to ad26032000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting BLANK keyword from ad26032000g320170.cal
-> gis3v4_0.rmf already present in current directory
-> Plotting ad26032000g320170_cal.ps and finding peak
-> Standard Output From STOOL xspec:

               Xspec 11.00 12:41:19 12-Jul-2000
http://xspec.gsfc.nasa.gov/

 Plot device not set, use "cpd" to set it

 Type "help" or "?" for further information

Executing script file "z.xco" ...


!XSPEC>   query yes;
Querying disabled - assuming answer is yes

!XSPEC>   data ad26032000g320170.cal;
 Net count rate (cts/s) for file   1  0.1208    +/-  1.9007E-03
   using response (RMF) file...       gis3v4_0.rmf
   1 data set is in use

!XSPEC>   ignore bad;

!XSPEC>   ignore **-4.0;

!XSPEC>   ignore 8.0-**;

!XSPEC>   model powerlaw/b + gauss/b + gauss/b ;0.0 ; ;5.9 ;0.0 ; ;6.5 ;0.0 ; ;
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
Param# 1  :!Param# 1  : 0.0 
Param# 2  :!Param# 2  : 
Param# 3  :!Param# 3  : 5.9 
Param# 4  :!Param# 4  : 0.0 
Param# 5  :!Param# 5  : 
Param# 6  :!Param# 6  : 6.5 
Param# 7  :!Param# 7  : 0.0 
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     +/-      0.
    2    2    1   powerlaw/b norm                1.000     +/-      0.
    3    3    2   gaussian/b LineE    keV        5.900     +/-      0.
    4    4    2   gaussian/b Sigma    keV           0.     +/-      0.
    5    5    2   gaussian/b norm                1.000     +/-      0.
    6    6    3   gaussian/b LineE    keV        6.500     +/-      0.
    7    7    3   gaussian/b Sigma    keV           0.     +/-      0.
    8    8    3   gaussian/b norm                1.000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =     5.8382936E+07 using    84 PHA bins.
 Reduced chi-squared =      768196.5     for     76 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 6 = 3 1.101005;
Equating parameter :LineE to parameter gaussian:LineE  * 1.10101
    7 variable fit parameters
 Chi-Squared =     5.8382936E+07 using    84 PHA bins.
 Reduced chi-squared =      758219.9     for     77 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   newpar 7 = 4 1.049288;
Equating parameter :Sigma to parameter :Sigma  * 1.04929
    6 variable fit parameters
 Chi-Squared =     5.8382936E+07 using    84 PHA bins.
 Reduced chi-squared =      748499.2     for     78 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   freeze 1;
 Number of variable fit parameters =    5

!XSPEC>   renorm;
 Chi-Squared =      2381.138     using    84 PHA bins.
 Reduced chi-squared =      30.14099     for     79 degrees of freedom
 Null hypothesis probability =    0.

!XSPEC>   fit;
 Chi-Squared    Lvl  Fit param # 1     2           3           4
                 5           6
   194.242     -1         0.      8.9460E-04   5.875          0.
              6.3835E-02  1.6684E-02
   185.090     -2         0.      1.6482E-03   5.878          0.
              6.7129E-02  1.6026E-02
   182.390     -3         0.      1.0815E-03   5.879          0.
              6.7083E-02  1.6095E-02
   181.348     -4         0.      1.5073E-03   5.879          0.
              6.7087E-02  1.6091E-02
   180.490     -5         0.      1.1774E-03   5.880          0.
              6.7087E-02  1.6091E-02
   180.097     -6         0.      1.4281E-03   5.881          0.
              6.7087E-02  1.6091E-02
   179.818     -7         0.      1.2345E-03   5.881          0.
              6.7087E-02  1.6091E-02
   179.674     -8         0.      1.3822E-03   5.882          0.
              6.7087E-02  1.6091E-02
   179.582     -9         0.      1.2685E-03   5.882          0.
              6.7087E-02  1.6091E-02
 Number of trials exceeded - last iteration delta =   9.2346E-02
   179.530    -10         0.      1.3554E-03   5.883          0.
              6.7087E-02  1.6091E-02
   179.499    -11         0.      1.2886E-03   5.884          0.
              6.7087E-02  1.6091E-02
   179.481    -12         0.      1.3398E-03   5.884          0.
              6.7087E-02  1.6091E-02
   179.471    -13         0.      1.3004E-03   5.885          0.
              6.7087E-02  1.6091E-02
   179.464    -14         0.      1.3306E-03   5.886          0.
              6.7087E-02  1.6091E-02
   108.902      0         0.      1.2612E-03   5.888      0.1448
              6.7551E-02  1.5591E-02
   85.7806     -1         0.      9.3056E-04   5.912      0.1469
              7.2708E-02  1.3186E-02
   84.5790     -2         0.      1.1825E-03   5.917      0.1466
              7.3938E-02  1.2348E-02
   84.2731     -3         0.      9.9201E-04   5.917      0.1456
              7.3941E-02  1.2314E-02
   84.1532     -4         0.      1.1446E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
 Number of trials exceeded - last iteration delta =   0.1199
   84.0615     -5         0.      1.0214E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
   84.0088     -6         0.      1.1203E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
   83.9713     -7         0.      1.0404E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
   83.9486     -8         0.      1.1047E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
   83.9330     -9         0.      1.0528E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
   83.9232    -10         0.      1.0946E-03   5.917      0.1456
              7.3947E-02  1.2308E-02
 ---------------------------------------------------------------------------
 Variances and Principal axes :
               2     3     4     5     6
 6.20E-08 | -1.00  0.00 -0.01 -0.02 -0.07
 6.19E-07 |  0.07 -0.06 -0.02 -0.08 -0.99
 2.44E-06 | -0.02 -0.06 -0.06  0.99 -0.08
 3.82E-05 |  0.01  0.88 -0.48  0.02 -0.05
 1.24E-04 |  0.00  0.47  0.88  0.07 -0.05
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  Model:  powerlaw/b[1] + gaussian/b[2] + gaussian/b[3]
  Model Fit Model Component  Parameter  Unit     Value
  par   par comp
    1    1    1   powerlaw/b PhoIndex               0.     frozen
    2    2    1   powerlaw/b norm               1.0946E-03 +/-  0.2625E-03
    3    3    2   gaussian/b LineE    keV        5.917     +/-  0.7573E-02
    4    4    2   gaussian/b Sigma    keV       0.1456     +/-  0.1020E-01
    5    5    2   gaussian/b norm               7.3947E-02 +/-  0.1762E-02
    6    3    3   gaussian/b LineE    keV        6.515     = par   3 *   1.101
    7    4    3   gaussian/b Sigma    keV       0.1528     = par   4 *   1.049
    8    6    3   gaussian/b norm               1.2308E-02 +/-  0.1022E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      83.92324     using    84 PHA bins.
 Reduced chi-squared =      1.062320     for     79 degrees of freedom
 Null hypothesis probability = 0.331

!XSPEC>   setplot energy;

!XSPEC>   setplot com label top GIS3 Calibration Source, should peak near 5.9 keV;

!XSPEC>   setplot com log x off;

!XSPEC>   setplot com rescale x 4 8;

!XSPEC>   setplot com hard /ps;

!XSPEC>   plot;

!XSPEC>   exit;
 XSPEC: quit

!XSPEC>    tclexit
-> Calibration source ad26032000g320170.cal peaks at 5.917 +/- 0.007573 keV

Extracting bright and dark Earth event files. (12:41:24)

-> Extracting bright and dark Earth events from ad26032000s000102h.unf
-> Extracting ad26032000s000102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.18E+05    32153 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          32153      1408              0     30745         0         0
 Writing events file
   1408 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         32153      1408              0     30745         0         0
   in  1535.3     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s000102h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1408
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        1106
 Flickering pixels iter, pixels & cnts :   1           1          10
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :         1408
 Number of image cts rejected (N, %) :         111679.26
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            0            0
 
 Image counts      :             0         1408            0            0
 Image cts rejected:             0         1116            0            0
 Image cts rej (%) :          0.00        79.26         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1408            0            0
 Total cts rejected:             0         1116            0            0
 Total cts rej (%) :          0.00        79.26         0.00         0.00
 
 Number of clean counts accepted  :          292
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000112h.unf
-> Extracting ad26032000s000112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.18E+05    32508 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          32508      1505              0     31003         0         0
 Writing events file
   1505 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         32508      1505              0     31003         0         0
   in  1535.3     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s000112h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1505
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7        1106
 Flickering pixels iter, pixels & cnts :   1           1          10
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :         1505
 Number of image cts rejected (N, %) :         111674.15
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            0            0
 
 Image counts      :             0         1505            0            0
 Image cts rejected:             0         1116            0            0
 Image cts rej (%) :          0.00        74.15         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1505            0            0
 Total cts rejected:             0         1116            0            0
 Total cts rej (%) :          0.00        74.15         0.00         0.00
 
 Number of clean counts accepted  :          389
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000202m.unf
-> Extracting ad26032000s000202m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.16E+05    28830 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000202m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          28830       418              0     28412         0         0
 Writing events file
    418 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         28830       418              0     28412         0         0
   in  448.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s000202m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000202m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          418
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7         369
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            7
 Number of (internal) image counts   :          418
 Number of image cts rejected (N, %) :          36988.28
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            7            0            0
 
 Image counts      :             0          418            0            0
 Image cts rejected:             0          369            0            0
 Image cts rej (%) :          0.00        88.28         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          418            0            0
 Total cts rejected:             0          369            0            0
 Total cts rej (%) :          0.00        88.28         0.00         0.00
 
 Number of clean counts accepted  :           49
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            7
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000212m.unf
-> Extracting ad26032000s000212m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.16E+05    29099 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000212m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          29099       435              0     28664         0         0
 Writing events file
    435 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         29099       435              0     28664         0         0
   in  448.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s000212m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000212m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          435
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7         369
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            7
 Number of (internal) image counts   :          435
 Number of image cts rejected (N, %) :          36984.83
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            7            0            0
 
 Image counts      :             0          435            0            0
 Image cts rejected:             0          369            0            0
 Image cts rej (%) :          0.00        84.83         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          435            0            0
 Total cts rejected:             0          369            0            0
 Total cts rej (%) :          0.00        84.83         0.00         0.00
 
 Number of clean counts accepted  :           66
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            7
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000302l.unf
-> Extracting ad26032000s000302l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      LOW         1998-05-13  17:57:44    0.40E+04     1348 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000302l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1348       817              0       531         0         0
 Writing events file
    817 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1348       817              0       531         0         0
   in  1500.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s000302l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000302l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          817
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7         712
 Flickering pixels iter, pixels & cnts :   1           1           4
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :          817
 Number of image cts rejected (N, %) :          71687.64
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            0            0
 
 Image counts      :             0          817            0            0
 Image cts rejected:             0          716            0            0
 Image cts rej (%) :          0.00        87.64         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          817            0            0
 Total cts rejected:             0          716            0            0
 Total cts rej (%) :          0.00        87.64         0.00         0.00
 
 Number of clean counts accepted  :          101
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000312l.unf
-> Extracting ad26032000s000312l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     LOW         1998-05-13  17:57:44    0.40E+04     1373 0100
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000312l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1373       832              0       541         0         0
 Writing events file
    832 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1373       832              0       541         0         0
   in  1500.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s000312l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000312l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          832
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :               7         712
 Flickering pixels iter, pixels & cnts :   1           1           4
cleaning chip # 2
cleaning chip # 3
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :          832
 Number of image cts rejected (N, %) :          71686.06
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            8            0            0
 
 Image counts      :             0          832            0            0
 Image cts rejected:             0          716            0            0
 Image cts rej (%) :          0.00        86.06         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          832            0            0
 Total cts rejected:             0          716            0            0
 Total cts rej (%) :          0.00        86.06         0.00         0.00
 
 Number of clean counts accepted  :          116
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000402h.unf
-> Extracting ad26032000s000402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-14  03:16:54    0.23E+03     3133 1001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000402h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3133      3133              0         0         0         0
 Writing events file
   3133 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3133      3133              0         0         0         0
   in  232.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s000402h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000402h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3133
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              66        1628
 Flickering pixels iter, pixels & cnts :   1          32         227
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              36         764
 Flickering pixels iter, pixels & cnts :   1          27         148
 
 Number of pixels rejected           :          161
 Number of (internal) image counts   :         3133
 Number of image cts rejected (N, %) :         276788.32
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            98            0            0           63
 
 Image counts      :          2139            0            0          994
 Image cts rejected:          1855            0            0          912
 Image cts rej (%) :         86.72         0.00         0.00        91.75
 
    filtering data...
 
 Total counts      :          2139            0            0          994
 Total cts rejected:          1855            0            0          912
 Total cts rej (%) :         86.72         0.00         0.00        91.75
 
 Number of clean counts accepted  :          366
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          161
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s000412h.unf
-> Extracting ad26032000s000412h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S0CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-14  03:16:54    0.23E+03     3171 1001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s000412h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3171      3171              0         0         0         0
 Writing events file
   3171 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3171      3171              0         0         0         0
   in  232.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s000412h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s000412h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s000412h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3171
 
    copy bad pix array...
cleaning chip # 0
 Hot pixels & counts                   :              66        1637
 Flickering pixels iter, pixels & cnts :   1          32         227
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              36         764
 Flickering pixels iter, pixels & cnts :   1          27         148
 
 Number of pixels rejected           :          161
 Number of (internal) image counts   :         3171
 Number of image cts rejected (N, %) :         277687.54
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            98            0            0           63
 
 Image counts      :          2173            0            0          998
 Image cts rejected:          1864            0            0          912
 Image cts rej (%) :         85.78         0.00         0.00        91.38
 
    filtering data...
 
 Total counts      :          2173            0            0          998
 Total cts rejected:          1864            0            0          912
 Total cts rej (%) :         85.78         0.00         0.00        91.38
 
 Number of clean counts accepted  :          395
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          161
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100102h.unf
-> Extracting ad26032000s100102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-13  21:43:04    0.18E+05    63024 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          63024      4747              0     58277         0         0
 Writing events file
   4747 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         63024      4747              0     58277         0         0
   in  1663.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100102h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s100102h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4747
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              15        4379
 Flickering pixels iter, pixels & cnts :   1           8          35
 
 Number of pixels rejected           :           23
 Number of (internal) image counts   :         4747
 Number of image cts rejected (N, %) :         441492.99
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           23
 
 Image counts      :             0            0            0         4747
 Image cts rejected:             0            0            0         4414
 Image cts rej (%) :          0.00         0.00         0.00        92.99
 
    filtering data...
 
 Total counts      :             0            0            0         4747
 Total cts rejected:             0            0            0         4414
 Total cts rej (%) :          0.00         0.00         0.00        92.99
 
 Number of clean counts accepted  :          333
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           23
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100112h.unf
-> Extracting ad26032000s100112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-13  21:43:04    0.18E+05    63293 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          63293      4800              0     58493         0         0
 Writing events file
   4800 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         63293      4800              0     58493         0         0
   in  1663.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100112h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s100112h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4800
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              15        4379
 Flickering pixels iter, pixels & cnts :   1           8          35
 
 Number of pixels rejected           :           23
 Number of (internal) image counts   :         4800
 Number of image cts rejected (N, %) :         441491.96
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           23
 
 Image counts      :             0            0            0         4800
 Image cts rejected:             0            0            0         4414
 Image cts rej (%) :          0.00         0.00         0.00        91.96
 
    filtering data...
 
 Total counts      :             0            0            0         4800
 Total cts rejected:             0            0            0         4414
 Total cts rej (%) :          0.00         0.00         0.00        91.96
 
 Number of clean counts accepted  :          386
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           23
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100202m.unf
-> Extracting ad26032000s100202m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      MEDIUM      1998-05-13  17:51:36    0.16E+05    54939 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100202m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          54939      1263              0     53676         0         0
 Writing events file
   1263 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         54939      1263              0     53676         0         0
   in  448.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100202m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s100202m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100202m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1263
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              15        1202
 Flickering pixels iter, pixels & cnts :   1           3          11
 
 Number of pixels rejected           :           18
 Number of (internal) image counts   :         1263
 Number of image cts rejected (N, %) :         121396.04
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           18
 
 Image counts      :             0            0            0         1263
 Image cts rejected:             0            0            0         1213
 Image cts rej (%) :          0.00         0.00         0.00        96.04
 
    filtering data...
 
 Total counts      :             0            0            0         1263
 Total cts rejected:             0            0            0         1213
 Total cts rej (%) :          0.00         0.00         0.00        96.04
 
 Number of clean counts accepted  :           50
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           18
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100212m.unf
-> Extracting ad26032000s100212m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     MEDIUM      1998-05-13  17:51:36    0.16E+05    55118 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100212m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          55118      1273              0     53845         0         0
 Writing events file
   1273 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         55118      1273              0     53845         0         0
   in  448.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100212m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s100212m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100212m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1273
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              15        1202
 Flickering pixels iter, pixels & cnts :   1           3          11
 
 Number of pixels rejected           :           18
 Number of (internal) image counts   :         1273
 Number of image cts rejected (N, %) :         121395.29
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           18
 
 Image counts      :             0            0            0         1273
 Image cts rejected:             0            0            0         1213
 Image cts rej (%) :          0.00         0.00         0.00        95.29
 
    filtering data...
 
 Total counts      :             0            0            0         1273
 Total cts rejected:             0            0            0         1213
 Total cts rej (%) :          0.00         0.00         0.00        95.29
 
 Number of clean counts accepted  :           60
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           18
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100302l.unf
-> Extracting ad26032000s100302l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      LOW         1998-05-13  17:57:44    0.40E+04     2907 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100302l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2907      1484              0      1423         0         0
 Writing events file
   1484 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2907      1484              0      1423         0         0
   in  1504.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100302l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s100302l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100302l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1484
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              11        1381
 Flickering pixels iter, pixels & cnts :   1           4          33
 
 Number of pixels rejected           :           15
 Number of (internal) image counts   :         1484
 Number of image cts rejected (N, %) :         141495.28
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           15
 
 Image counts      :             0            0            0         1484
 Image cts rejected:             0            0            0         1414
 Image cts rej (%) :          0.00         0.00         0.00        95.28
 
    filtering data...
 
 Total counts      :             0            0            0         1484
 Total cts rejected:             0            0            0         1414
 Total cts rej (%) :          0.00         0.00         0.00        95.28
 
 Number of clean counts accepted  :           70
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           15
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100312l.unf
-> Extracting ad26032000s100312l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     LOW         1998-05-13  17:57:44    0.40E+04     2922 0001
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100312l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2922      1494              0      1428         0         0
 Writing events file
   1494 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2922      1494              0      1428         0         0
   in  1504.1     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100312l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s100312l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100312l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1494
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
 Hot pixels & counts                   :              11        1382
 Flickering pixels iter, pixels & cnts :   1           4          33
 
 Number of pixels rejected           :           15
 Number of (internal) image counts   :         1494
 Number of image cts rejected (N, %) :         141594.71
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           15
 
 Image counts      :             0            0            0         1494
 Image cts rejected:             0            0            0         1415
 Image cts rej (%) :          0.00         0.00         0.00        94.71
 
    filtering data...
 
 Total counts      :             0            0            0         1494
 Total cts rejected:             0            0            0         1415
 Total cts rej (%) :          0.00         0.00         0.00        94.71
 
 Number of clean counts accepted  :           79
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           15
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100402h.unf
-> Extracting ad26032000s100402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT      HIGH        1998-05-14  04:58:14    0.22E+03     4180 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100402h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4180      1926              0      2254         0         0
 Writing events file
   1926 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4180      1926              0      2254         0         0
   in  112.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100402h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad26032000s100402h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100402h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1926
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              57         717
 Flickering pixels iter, pixels & cnts :   1          42         231
cleaning chip # 2
 Hot pixels & counts                   :              55         677
 Flickering pixels iter, pixels & cnts :   1          42         220
cleaning chip # 3
 
 Number of pixels rejected           :          196
 Number of (internal) image counts   :         1926
 Number of image cts rejected (N, %) :         184595.79
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           99           97            0
 
 Image counts      :             0          984          942            0
 Image cts rejected:             0          948          897            0
 Image cts rej (%) :          0.00        96.34        95.22         0.00
 
    filtering data...
 
 Total counts      :             0          984          942            0
 Total cts rejected:             0          948          897            0
 Total cts rej (%) :          0.00        96.34        95.22         0.00
 
 Number of clean counts accepted  :           81
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          196
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000s100412h.unf
-> Extracting ad26032000s100412h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  S1CCDPOW
      1 WR 140      BRIGHT2     HIGH        1998-05-14  04:58:14    0.22E+03     4190 0110
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000s100412h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4190      1926              0      2264         0         0
 Writing events file
   1926 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4190      1926              0      2264         0         0
   in  112.00     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000s100412h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    4
 WMAP   keywords   = DETX       DETY        with binning =    8
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   8.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad26032000s100412h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad26032000s100412h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1926
 
    copy bad pix array...
cleaning chip # 0
cleaning chip # 1
 Hot pixels & counts                   :              57         717
 Flickering pixels iter, pixels & cnts :   1          42         231
cleaning chip # 2
 Hot pixels & counts                   :              55         677
 Flickering pixels iter, pixels & cnts :   1          42         220
cleaning chip # 3
 
 Number of pixels rejected           :          196
 Number of (internal) image counts   :         1926
 Number of image cts rejected (N, %) :         184595.79
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0           99           97            0
 
 Image counts      :             0          984          942            0
 Image cts rejected:             0          948          897            0
 Image cts rej (%) :          0.00        96.34        95.22         0.00
 
    filtering data...
 
 Total counts      :             0          984          942            0
 Total cts rejected:             0          948          897            0
 Total cts rej (%) :          0.00        96.34        95.22         0.00
 
 Number of clean counts accepted  :           81
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          196
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad26032000g200170h.unf
-> Extracting ad26032000g200170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          25180      1511              0     23669         0         0
 Writing events file
   1511 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         25180      1511              0     23669         0         0
   in  2579.7     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad26032000g200170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    25180     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          25180      4732              0     20448         0         0
 Writing events file
   4732 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         25180      4732              0     20448         0         0
   in  2640.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad26032000g200270m.unf
-> Extracting ad26032000g200270m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20914     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad26032000g200270m.drk since it contains 0 events
-> Extracting ad26032000g200270m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20914     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20914      3974              0     16940         0         0
 Writing events file
   3974 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20914      3974              0     16940         0         0
   in  1711.9     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad26032000g200370l.unf
-> Extracting ad26032000g200370l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3128     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3128       360              0      2768         0         0
 Writing events file
    360 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3128       360              0      2768         0         0
   in  640.15     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad26032000g200370l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3128     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3128      2561              0       567         0         0
 Writing events file
   2561 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3128      2561              0       567         0         0
   in  1152.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g200370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad26032000g300170h.unf
-> Extracting ad26032000g300170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          24859      1376              0     23483         0         0
 Writing events file
   1376 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         24859      1376              0     23483         0         0
   in  2579.7     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad26032000g300170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          HIGH        1998-05-13  21:43:18    0.18E+05    24859     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          24859      4671              0     20188         0         0
 Writing events file
   4671 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         24859      4671              0     20188         0         0
   in  2640.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300170h.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad26032000g300270m.unf
-> Extracting ad26032000g300270m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20901     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 No events selected from file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in      0.     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad26032000g300270m.drk since it contains 0 events
-> Extracting ad26032000g300270m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          MEDIUM      1998-05-13  18:05:04    0.14E+05    20901     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          20901      4031              0     16870         0         0
 Writing events file
   4031 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20901      4031              0     16870         0         0
   in  1711.9     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300270m.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad26032000g300370l.unf
-> Extracting ad26032000g300370l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3184     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3184       351              0      2833         0         0
 Writing events file
    351 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3184       351              0      2833         0         0
   in  640.15     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad26032000g300370l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V2.0   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
 
 
        OBJECT      DATAMODE    BIT_RATE    DATE-OBS    TIME-OBS    ONTIME   NEVENTS  PHA_BINS
      1 WR 140      PH          LOW         1998-05-13  18:02:08    0.20E+04     3184     1024
extractor v3.71  3 Jan 2000
 Getting FITS WCS Keywords
 Doing file: /data/data13/seq_proc/ad0_26032000.004/ad26032000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3184      2628              0       556         0         0
 Writing events file
   2628 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3184      2628              0       556         0         0
   in  1152.0     seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Time keyword is TIME       in units of s
 Default timing binsize =   16.000
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data13/seq_proc/ad0_26032000.004/
Setting mkf directory to /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA > read events ad26032000g300370l.unf
 
Setting...
 Image  keywords   = X          Y           with binning =    1
 WMAP   keywords   = DETX       DETY        with binning =    1
 Energy keywords   = PI                     with binning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data13/seq_proc/ad0_26032000.004/
HK Directory is: /data/data13/seq_proc/ad0_26032000.004/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=.
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

Determining information about this observation (12:55:24)

-> Calculating ISAS time for sis
-> Calculating ISAS time for gis
-> Recording dates of PI calibration files
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory
-> leapsec.fits is already present in the working directory

Generating event file information page (12:56:30)

-> Summing time and events for s0 event files
-> Standard Output From STOOL get_uniq_keys:
ad26032000s000102h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000402h.unf|S0CCDPOW|1001|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000102h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000402h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000102h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order
ad26032000s000402h.unf|S0CCDLST|3 0 3 0|S0 CCD readout order
-> listing ad26032000s000102h.unf
-> listing ad26032000s000402h.unf
-> listing ad26032000s000202m.unf
-> listing ad26032000s000302l.unf
-> Standard Output From STOOL get_uniq_keys:
ad26032000s000112h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000412h.unf|S0CCDPOW|1001|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000112h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000412h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000112h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order
ad26032000s000412h.unf|S0CCDLST|3 0 3 0|S0 CCD readout order
-> listing ad26032000s000112h.unf
-> listing ad26032000s000412h.unf
-> listing ad26032000s000212m.unf
-> listing ad26032000s000312l.unf
-> Standard Output From STOOL get_uniq_keys:
ad26032000s000101h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000401h.unf|S0CCDPOW|1001|Which S0 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s000101h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000401h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4
ad26032000s000101h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order
ad26032000s000401h.unf|S0CCDLST|3 0 3 0|S0 CCD readout order
-> listing ad26032000s000101h.unf
-> listing ad26032000s000401h.unf
-> listing ad26032000s000201m.unf
-> listing ad26032000s000301l.unf
-> Summing time and events for s1 event files
-> Standard Output From STOOL get_uniq_keys:
ad26032000s100102h.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100402h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100102h.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100402h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100102h.unf|S1CCDLST|3 3 3 3|S1 CCD readout order
ad26032000s100402h.unf|S1CCDLST|1 2 1 2|S1 CCD readout order
-> listing ad26032000s100102h.unf
-> listing ad26032000s100402h.unf
-> listing ad26032000s100202m.unf
-> listing ad26032000s100302l.unf
-> Standard Output From STOOL get_uniq_keys:
ad26032000s100112h.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100412h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100112h.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100412h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100112h.unf|S1CCDLST|3 3 3 3|S1 CCD readout order
ad26032000s100412h.unf|S1CCDLST|1 2 1 2|S1 CCD readout order
-> listing ad26032000s100112h.unf
-> listing ad26032000s100412h.unf
-> listing ad26032000s100212m.unf
-> listing ad26032000s100312l.unf
-> Standard Output From STOOL get_uniq_keys:
ad26032000s100101h.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100401h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad26032000s100101h.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100401h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad26032000s100101h.unf|S1CCDLST|3 3 3 3|S1 CCD readout order
ad26032000s100401h.unf|S1CCDLST|1 2 1 2|S1 CCD readout order
-> listing ad26032000s100101h.unf
-> listing ad26032000s100401h.unf
-> listing ad26032000s100201m.unf
-> listing ad26032000s100301l.unf
-> Summing time and events for g2 event files
-> listing ad26032000g200170h.unf
-> listing ad26032000g200270m.unf
-> listing ad26032000g200370l.unf
-> Summing time and events for g3 event files
-> listing ad26032000g300170h.unf
-> listing ad26032000g300270m.unf
-> listing ad26032000g300370l.unf

Creating HTML header page (13:2:41)

Creating HTML source list (13:2:59)

Doing final wrapup of all files (13:4:34)

-> Copying job.par to ad26032000_004_job.par
-> Copying ad0.par to ad26032000_004_process.par
-> Creating ad26032000_tape.cat
-> Creating ad26032000_trend.cat
-> Creating ad26032000_004_file_info.html
-> Calculating site-independant checksums
-> Site independant checksum: 64802
-> Updating FITS checksum keywords
-> Running fverify on all FITS files

Processing complete (13:27:8)