The following information is also available:
Time column is TIME ORDERED-> Fetching fa960315_1951.0420.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 101073070.950300 101103693.846800
Data file start and stop ascatime : 101073070.950300 101103693.846800
Aspecting run start and stop ascatime : 101073070.950378 101103693.846720
Time interval averaged over (seconds) : 30622.896342
Total pointing and manuver time (sec) : 19985.480469 10637.480469
Mean boresight Euler angles : 263.108722 123.118818 356.983662
RA DEC SUN ANGLE
Mean solar position (deg) : 355.13 -2.11
Mean aberration (arcsec) : 0.43 3.48
Mean sat X-axis (deg) : 88.617408 -56.759698 90.15
Mean sat Y-axis (deg) : 354.757840 -2.525953 0.56
Mean sat Z-axis (deg) : 263.108722 -33.118819 90.54
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 263.416534 -32.999428 267.151978 0.073140
Minimum 263.410004 -33.006119 267.143250 0.000000
Maximum 263.720703 -32.601158 267.272675 28.396095
Sigma (RMS) 0.000434 0.000423 0.002380 0.194251
Number of ASPECT records processed = 28632
Aspecting to RA/DEC : 263.41653442 -32.99942780
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 263.417 DEC: -32.999
START TIME: SC 101073070.9504 = UT 15/03/96 19:51:10
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500096 0.173 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
2682.990967 0.139 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
4828.983887 0.071 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
8428.971680 0.015 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
10574.963867 0.026 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
14214.952148 0.017 DC28C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 3
16320.945312 0.049 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
19974.931641 0.088 DC28C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 3
22086.925781 0.027 DC20C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 3
25734.912109 0.106 DC28C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 3
27846.906250 0.110 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
30582.896484 15.184 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
30622.896484 28.396 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
Attitude Records: 28632
Attitude Steps: 13
Maneuver ACM time: 10637.5 sec
Pointed ACM time: 19985.5 sec
-> Calculating aspect point99 99 count=1204 sum1=316782 sum2=148232 sum3=429813 99 100 count=25308 sum1=6.65875e+06 sum2=3.11589e+06 sum3=9.03454e+06 100 100 count=2117 sum1=557004 sum2=260641 sum3=755739 115 78 count=1 sum1=263.263 sum2=122.901 sum3=357.042 130 60 count=1 sum1=263.415 sum2=122.721 sum3=357.107 0 out of 28631 points outside bin structure-> Euler angles: 263.109, 123.119, 356.984
Interpolating 24 records in time interval 1.01104e+08 - 1.01104e+08 Interpolating 21 records in time interval 1.01104e+08 - 1.01104e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft960315_1951.0420",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft960315_1951.0420 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 393256 Bright = 21848 Fast = 0 Frame = 43584 Dark frame = 0 Histogram = 0 Integration = 0 PH = 458688 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 7204 no. of SIS events found = 621368-> Standard Error Output From FTOOL frfread
coordinate error 384 0 coordinate error 0 24 coordinate error 0 0 coordinate error 12 0-> Removing the following files with NEVENTS=0
ft960315_1951_0420G201270M.fits ft960315_1951_0420G201370H.fits ft960315_1951_0420G201470H.fits ft960315_1951_0420G202570H.fits ft960315_1951_0420G202670H.fits ft960315_1951_0420G202770L.fits ft960315_1951_0420G202870L.fits ft960315_1951_0420G202970H.fits ft960315_1951_0420G203070H.fits ft960315_1951_0420G203170H.fits ft960315_1951_0420G203270H.fits ft960315_1951_0420G203370H.fits ft960315_1951_0420G203570H.fits ft960315_1951_0420G203970L.fits ft960315_1951_0420G204099.fits ft960315_1951_0420G204170H.fits ft960315_1951_0420G204370H.fits ft960315_1951_0420G204970L.fits ft960315_1951_0420G205070H.fits ft960315_1951_0420G205270H.fits ft960315_1951_0420G205599.fits ft960315_1951_0420G205799.fits ft960315_1951_0420G206170L.fits ft960315_1951_0420G206270M.fits ft960315_1951_0420G206370L.fits ft960315_1951_0420G206470L.fits ft960315_1951_0420G206570M.fits ft960315_1951_0420G206670M.fits ft960315_1951_0420G206770M.fits ft960315_1951_0420G206870M.fits ft960315_1951_0420G206970H.fits ft960315_1951_0420G207070H.fits ft960315_1951_0420G207170H.fits ft960315_1951_0420G207270H.fits ft960315_1951_0420G207370H.fits ft960315_1951_0420G207470H.fits ft960315_1951_0420G301170M.fits ft960315_1951_0420G301270M.fits ft960315_1951_0420G301370H.fits ft960315_1951_0420G301570H.fits ft960315_1951_0420G302170H.fits ft960315_1951_0420G302270H.fits ft960315_1951_0420G302370L.fits ft960315_1951_0420G302470L.fits ft960315_1951_0420G302570H.fits ft960315_1951_0420G302670H.fits ft960315_1951_0420G302770H.fits ft960315_1951_0420G302870H.fits ft960315_1951_0420G303570L.fits ft960315_1951_0420G303699.fits ft960315_1951_0420G303770H.fits ft960315_1951_0420G303870H.fits ft960315_1951_0420G304570L.fits ft960315_1951_0420G304670H.fits ft960315_1951_0420G304770H.fits ft960315_1951_0420G305199.fits ft960315_1951_0420G305399.fits ft960315_1951_0420G305870M.fits ft960315_1951_0420G305970L.fits ft960315_1951_0420G306070L.fits ft960315_1951_0420G306170M.fits ft960315_1951_0420G306270M.fits ft960315_1951_0420G306370M.fits ft960315_1951_0420G306470M.fits ft960315_1951_0420G306570H.fits ft960315_1951_0420G306670H.fits ft960315_1951_0420G306770H.fits ft960315_1951_0420G306870H.fits ft960315_1951_0420G306970H.fits ft960315_1951_0420G307070H.fits ft960315_1951_0420S000302H.fits ft960315_1951_0420S000402L.fits ft960315_1951_0420S000502L.fits ft960315_1951_0420S000602L.fits ft960315_1951_0420S000902H.fits ft960315_1951_0420S001002H.fits ft960315_1951_0420S001701H.fits ft960315_1951_0420S001804H.fits ft960315_1951_0420S002502H.fits ft960315_1951_0420S002802L.fits ft960315_1951_0420S002999.fits ft960315_1951_0420S003099.fits ft960315_1951_0420S003302H.fits ft960315_1951_0420S003602L.fits ft960315_1951_0420S004199.fits ft960315_1951_0420S004399.fits ft960315_1951_0420S004502H.fits ft960315_1951_0420S005002L.fits ft960315_1951_0420S005502H.fits ft960315_1951_0420S005602L.fits ft960315_1951_0420S005702M.fits ft960315_1951_0420S100602H.fits ft960315_1951_0420S100702L.fits ft960315_1951_0420S100802L.fits ft960315_1951_0420S100902L.fits ft960315_1951_0420S101104H.fits ft960315_1951_0420S102102H.fits ft960315_1951_0420S102302L.fits ft960315_1951_0420S102499.fits ft960315_1951_0420S102599.fits ft960315_1951_0420S102702H.fits ft960315_1951_0420S102902L.fits ft960315_1951_0420S103399.fits ft960315_1951_0420S103599.fits ft960315_1951_0420S103702H.fits ft960315_1951_0420S104102L.fits ft960315_1951_0420S104502H.fits ft960315_1951_0420S104602L.fits ft960315_1951_0420S104702M.fits-> Checking for empty GTI extensions
ft960315_1951_0420S000101H.fits[3] ft960315_1951_0420S000201H.fits[3] ft960315_1951_0420S000702M.fits[3] ft960315_1951_0420S000802M.fits[3] ft960315_1951_0420S001102M.fits[3] ft960315_1951_0420S001201M.fits[3] ft960315_1951_0420S001301H.fits[3] ft960315_1951_0420S001401H.fits[3] ft960315_1951_0420S001501L.fits[3] ft960315_1951_0420S001601L.fits[3] ft960315_1951_0420S001901H.fits[3] ft960315_1951_0420S002001L.fits[3] ft960315_1951_0420S002101L.fits[3] ft960315_1951_0420S002201L.fits[3] ft960315_1951_0420S002301H.fits[3] ft960315_1951_0420S002401H.fits[3] ft960315_1951_0420S002602L.fits[3] ft960315_1951_0420S002702L.fits[3] ft960315_1951_0420S003101H.fits[3] ft960315_1951_0420S003201H.fits[3] ft960315_1951_0420S003402L.fits[3] ft960315_1951_0420S003502L.fits[3] ft960315_1951_0420S003702L.fits[3] ft960315_1951_0420S003801L.fits[3] ft960315_1951_0420S003901H.fits[3] ft960315_1951_0420S004001H.fits[3] ft960315_1951_0420S004201H.fits[3] ft960315_1951_0420S004401H.fits[3] ft960315_1951_0420S004602L.fits[3] ft960315_1951_0420S004702L.fits[3] ft960315_1951_0420S004802M.fits[3] ft960315_1951_0420S004902M.fits[3] ft960315_1951_0420S005102M.fits[3] ft960315_1951_0420S005201M.fits[3] ft960315_1951_0420S005301H.fits[3] ft960315_1951_0420S005401H.fits[3]-> Merging GTIs from the following files:
ft960315_1951_0420S100101H.fits[3] ft960315_1951_0420S100201H.fits[3] ft960315_1951_0420S100301H.fits[3] ft960315_1951_0420S100401H.fits[3] ft960315_1951_0420S100501H.fits[3] ft960315_1951_0420S101002M.fits[3] ft960315_1951_0420S101202M.fits[3] ft960315_1951_0420S101301M.fits[3] ft960315_1951_0420S101401H.fits[3] ft960315_1951_0420S101501L.fits[3] ft960315_1951_0420S101601H.fits[3] ft960315_1951_0420S101701L.fits[3] ft960315_1951_0420S101801L.fits[3] ft960315_1951_0420S101901L.fits[3] ft960315_1951_0420S102001H.fits[3] ft960315_1951_0420S102202L.fits[3] ft960315_1951_0420S102601H.fits[3] ft960315_1951_0420S102802L.fits[3] ft960315_1951_0420S103002L.fits[3] ft960315_1951_0420S103101L.fits[3] ft960315_1951_0420S103201H.fits[3] ft960315_1951_0420S103401H.fits[3] ft960315_1951_0420S103601H.fits[3] ft960315_1951_0420S103802L.fits[3] ft960315_1951_0420S103902M.fits[3] ft960315_1951_0420S104002M.fits[3] ft960315_1951_0420S104202M.fits[3] ft960315_1951_0420S104301M.fits[3] ft960315_1951_0420S104401H.fits[3]-> Merging GTIs from the following files:
ft960315_1951_0420G200170H.fits[3] ft960315_1951_0420G200270H.fits[3] ft960315_1951_0420G200370H.fits[3] ft960315_1951_0420G200470L.fits[3] ft960315_1951_0420G200570M.fits[3] ft960315_1951_0420G200670M.fits[3] ft960315_1951_0420G200770M.fits[3] ft960315_1951_0420G200870M.fits[3] ft960315_1951_0420G200970H.fits[3] ft960315_1951_0420G201070M.fits[3] ft960315_1951_0420G201170M.fits[3] ft960315_1951_0420G201570H.fits[3] ft960315_1951_0420G201670H.fits[3] ft960315_1951_0420G201770H.fits[3] ft960315_1951_0420G201870H.fits[3] ft960315_1951_0420G201970H.fits[3] ft960315_1951_0420G202070H.fits[3] ft960315_1951_0420G202170H.fits[3] ft960315_1951_0420G202270L.fits[3] ft960315_1951_0420G202370L.fits[3] ft960315_1951_0420G202470H.fits[3] ft960315_1951_0420G203470H.fits[3] ft960315_1951_0420G203670H.fits[3] ft960315_1951_0420G203770L.fits[3] ft960315_1951_0420G203870L.fits[3] ft960315_1951_0420G204270H.fits[3] ft960315_1951_0420G204470H.fits[3] ft960315_1951_0420G204570H.fits[3] ft960315_1951_0420G204670L.fits[3] ft960315_1951_0420G204770L.fits[3] ft960315_1951_0420G204870L.fits[3] ft960315_1951_0420G205170H.fits[3] ft960315_1951_0420G205370H.fits[3] ft960315_1951_0420G205470H.fits[3] ft960315_1951_0420G205670H.fits[3] ft960315_1951_0420G205870H.fits[3] ft960315_1951_0420G205970L.fits[3] ft960315_1951_0420G206070L.fits[3] ft960315_1951_0420G207570H.fits[3] ft960315_1951_0420G207670H.fits[3] ft960315_1951_0420G207770L.fits[3] ft960315_1951_0420G207870L.fits[3] ft960315_1951_0420G207970M.fits[3] ft960315_1951_0420G208070M.fits[3] ft960315_1951_0420G208170M.fits[3]-> Merging GTIs from the following files:
ft960315_1951_0420G300170H.fits[3] ft960315_1951_0420G300270H.fits[3] ft960315_1951_0420G300370H.fits[3] ft960315_1951_0420G300470L.fits[3] ft960315_1951_0420G300570M.fits[3] ft960315_1951_0420G300670M.fits[3] ft960315_1951_0420G300770M.fits[3] ft960315_1951_0420G300870M.fits[3] ft960315_1951_0420G300970H.fits[3] ft960315_1951_0420G301070M.fits[3] ft960315_1951_0420G301470H.fits[3] ft960315_1951_0420G301670H.fits[3] ft960315_1951_0420G301770H.fits[3] ft960315_1951_0420G301870L.fits[3] ft960315_1951_0420G301970L.fits[3] ft960315_1951_0420G302070H.fits[3] ft960315_1951_0420G302970H.fits[3] ft960315_1951_0420G303070H.fits[3] ft960315_1951_0420G303170H.fits[3] ft960315_1951_0420G303270H.fits[3] ft960315_1951_0420G303370L.fits[3] ft960315_1951_0420G303470L.fits[3] ft960315_1951_0420G303970H.fits[3] ft960315_1951_0420G304070H.fits[3] ft960315_1951_0420G304170H.fits[3] ft960315_1951_0420G304270L.fits[3] ft960315_1951_0420G304370L.fits[3] ft960315_1951_0420G304470L.fits[3] ft960315_1951_0420G304870H.fits[3] ft960315_1951_0420G304970H.fits[3] ft960315_1951_0420G305070H.fits[3] ft960315_1951_0420G305270H.fits[3] ft960315_1951_0420G305470H.fits[3] ft960315_1951_0420G305570L.fits[3] ft960315_1951_0420G305670L.fits[3] ft960315_1951_0420G305770L.fits[3] ft960315_1951_0420G307170H.fits[3] ft960315_1951_0420G307270H.fits[3] ft960315_1951_0420G307370L.fits[3] ft960315_1951_0420G307470L.fits[3] ft960315_1951_0420G307570M.fits[3] ft960315_1951_0420G307670M.fits[3] ft960315_1951_0420G307770M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 4 photon cnt = 18 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g200770h.prelist merge count = 13 photon cnt = 24412 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 16 GISSORTSPLIT:LO:g200270l.prelist merge count = 6 photon cnt = 4032 GISSORTSPLIT:LO:g200370l.prelist merge count = 4 photon cnt = 346 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270m.prelist merge count = 1 photon cnt = 188 GISSORTSPLIT:LO:g200370m.prelist merge count = 3 photon cnt = 33 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:Total filenames split = 45 GISSORTSPLIT:LO:Total split file cnt = 17 GISSORTSPLIT:LO:End program-> Creating ad54000060g200170h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420G200170H.fits 2 -- ft960315_1951_0420G200370H.fits 3 -- ft960315_1951_0420G200970H.fits 4 -- ft960315_1951_0420G201770H.fits 5 -- ft960315_1951_0420G201970H.fits 6 -- ft960315_1951_0420G202170H.fits 7 -- ft960315_1951_0420G202470H.fits 8 -- ft960315_1951_0420G203670H.fits 9 -- ft960315_1951_0420G204570H.fits 10 -- ft960315_1951_0420G205470H.fits 11 -- ft960315_1951_0420G205670H.fits 12 -- ft960315_1951_0420G205870H.fits 13 -- ft960315_1951_0420G207670H.fits Merging binary extension #: 2 1 -- ft960315_1951_0420G200170H.fits 2 -- ft960315_1951_0420G200370H.fits 3 -- ft960315_1951_0420G200970H.fits 4 -- ft960315_1951_0420G201770H.fits 5 -- ft960315_1951_0420G201970H.fits 6 -- ft960315_1951_0420G202170H.fits 7 -- ft960315_1951_0420G202470H.fits 8 -- ft960315_1951_0420G203670H.fits 9 -- ft960315_1951_0420G204570H.fits 10 -- ft960315_1951_0420G205470H.fits 11 -- ft960315_1951_0420G205670H.fits 12 -- ft960315_1951_0420G205870H.fits 13 -- ft960315_1951_0420G207670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060g200270l.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420G200470L.fits 2 -- ft960315_1951_0420G202370L.fits 3 -- ft960315_1951_0420G203770L.fits 4 -- ft960315_1951_0420G204770L.fits 5 -- ft960315_1951_0420G206070L.fits 6 -- ft960315_1951_0420G207870L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420G200470L.fits 2 -- ft960315_1951_0420G202370L.fits 3 -- ft960315_1951_0420G203770L.fits 4 -- ft960315_1951_0420G204770L.fits 5 -- ft960315_1951_0420G206070L.fits 6 -- ft960315_1951_0420G207870L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000346 events
ft960315_1951_0420G202270L.fits ft960315_1951_0420G204670L.fits ft960315_1951_0420G205970L.fits ft960315_1951_0420G207770L.fits-> Ignoring the following files containing 000000188 events
ft960315_1951_0420G200870M.fits-> Ignoring the following files containing 000000033 events
ft960315_1951_0420G200770M.fits ft960315_1951_0420G201070M.fits ft960315_1951_0420G208170M.fits-> Ignoring the following files containing 000000018 events
ft960315_1951_0420G201670H.fits ft960315_1951_0420G204470H.fits ft960315_1951_0420G205370H.fits ft960315_1951_0420G207570H.fits-> Ignoring the following files containing 000000016 events
ft960315_1951_0420G207970M.fits-> Ignoring the following files containing 000000016 events
ft960315_1951_0420G203870L.fits ft960315_1951_0420G204870L.fits-> Ignoring the following files containing 000000015 events
ft960315_1951_0420G208070M.fits-> Ignoring the following files containing 000000012 events
ft960315_1951_0420G200570M.fits-> Ignoring the following files containing 000000011 events
ft960315_1951_0420G202070H.fits-> Ignoring the following files containing 000000008 events
ft960315_1951_0420G200670M.fits-> Ignoring the following files containing 000000004 events
ft960315_1951_0420G200270H.fits-> Ignoring the following files containing 000000003 events
ft960315_1951_0420G201570H.fits ft960315_1951_0420G203470H.fits-> Ignoring the following files containing 000000002 events
ft960315_1951_0420G201870H.fits-> Ignoring the following files containing 000000002 events
ft960315_1951_0420G201170M.fits-> Ignoring the following files containing 000000002 events
ft960315_1951_0420G204270H.fits ft960315_1951_0420G205170H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g300370h.prelist merge count = 5 photon cnt = 18 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300570h.prelist merge count = 11 photon cnt = 25226 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300270l.prelist merge count = 2 photon cnt = 16 GISSORTSPLIT:LO:g300370l.prelist merge count = 6 photon cnt = 3731 GISSORTSPLIT:LO:g300470l.prelist merge count = 4 photon cnt = 359 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 162 GISSORTSPLIT:LO:g300270m.prelist merge count = 3 photon cnt = 40 GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:Total filenames split = 43 GISSORTSPLIT:LO:Total split file cnt = 15 GISSORTSPLIT:LO:End program-> Creating ad54000060g300170h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420G300170H.fits 2 -- ft960315_1951_0420G300370H.fits 3 -- ft960315_1951_0420G300970H.fits 4 -- ft960315_1951_0420G301770H.fits 5 -- ft960315_1951_0420G302070H.fits 6 -- ft960315_1951_0420G303270H.fits 7 -- ft960315_1951_0420G304170H.fits 8 -- ft960315_1951_0420G305070H.fits 9 -- ft960315_1951_0420G305270H.fits 10 -- ft960315_1951_0420G305470H.fits 11 -- ft960315_1951_0420G307270H.fits Merging binary extension #: 2 1 -- ft960315_1951_0420G300170H.fits 2 -- ft960315_1951_0420G300370H.fits 3 -- ft960315_1951_0420G300970H.fits 4 -- ft960315_1951_0420G301770H.fits 5 -- ft960315_1951_0420G302070H.fits 6 -- ft960315_1951_0420G303270H.fits 7 -- ft960315_1951_0420G304170H.fits 8 -- ft960315_1951_0420G305070H.fits 9 -- ft960315_1951_0420G305270H.fits 10 -- ft960315_1951_0420G305470H.fits 11 -- ft960315_1951_0420G307270H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060g300270l.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420G300470L.fits 2 -- ft960315_1951_0420G301970L.fits 3 -- ft960315_1951_0420G303370L.fits 4 -- ft960315_1951_0420G304370L.fits 5 -- ft960315_1951_0420G305670L.fits 6 -- ft960315_1951_0420G307470L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420G300470L.fits 2 -- ft960315_1951_0420G301970L.fits 3 -- ft960315_1951_0420G303370L.fits 4 -- ft960315_1951_0420G304370L.fits 5 -- ft960315_1951_0420G305670L.fits 6 -- ft960315_1951_0420G307470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000359 events
ft960315_1951_0420G301870L.fits ft960315_1951_0420G304270L.fits ft960315_1951_0420G305570L.fits ft960315_1951_0420G307370L.fits-> Ignoring the following files containing 000000162 events
ft960315_1951_0420G300870M.fits-> Ignoring the following files containing 000000040 events
ft960315_1951_0420G300770M.fits ft960315_1951_0420G301070M.fits ft960315_1951_0420G307770M.fits-> Ignoring the following files containing 000000018 events
ft960315_1951_0420G301670H.fits ft960315_1951_0420G303170H.fits ft960315_1951_0420G304070H.fits ft960315_1951_0420G304970H.fits ft960315_1951_0420G307170H.fits-> Ignoring the following files containing 000000016 events
ft960315_1951_0420G303470L.fits ft960315_1951_0420G304470L.fits-> Ignoring the following files containing 000000011 events
ft960315_1951_0420G300570M.fits-> Ignoring the following files containing 000000010 events
ft960315_1951_0420G307670M.fits-> Ignoring the following files containing 000000010 events
ft960315_1951_0420G300670M.fits-> Ignoring the following files containing 000000007 events
ft960315_1951_0420G303070H.fits ft960315_1951_0420G303970H.fits ft960315_1951_0420G304870H.fits-> Ignoring the following files containing 000000005 events
ft960315_1951_0420G307570M.fits-> Ignoring the following files containing 000000003 events
ft960315_1951_0420G301470H.fits ft960315_1951_0420G302970H.fits-> Ignoring the following files containing 000000002 events
ft960315_1951_0420G300270H.fits-> Ignoring the following files containing 000000001 events
ft960315_1951_0420G305770L.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 7 photon cnt = 156713 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 8 photon cnt = 107321 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 4 photon cnt = 976 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 1 photon cnt = 1264 SIS0SORTSPLIT:LO:s000501l.prelist merge count = 1 photon cnt = 8 SIS0SORTSPLIT:LO:s000601m.prelist merge count = 2 photon cnt = 64 SIS0SORTSPLIT:LO:s000702l.prelist merge count = 4 photon cnt = 20504 SIS0SORTSPLIT:LO:s000802l.prelist merge count = 3 photon cnt = 1441 SIS0SORTSPLIT:LO:s000902m.prelist merge count = 4 photon cnt = 15538 SIS0SORTSPLIT:LO:s001002m.prelist merge count = 1 photon cnt = 379 SIS0SORTSPLIT:LO:s001102m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:Total filenames split = 36 SIS0SORTSPLIT:LO:Total split file cnt = 11 SIS0SORTSPLIT:LO:End program-> Creating ad54000060s000101h.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S000101H.fits 2 -- ft960315_1951_0420S001301H.fits 3 -- ft960315_1951_0420S001901H.fits 4 -- ft960315_1951_0420S002301H.fits 5 -- ft960315_1951_0420S003101H.fits 6 -- ft960315_1951_0420S003901H.fits 7 -- ft960315_1951_0420S005301H.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S000101H.fits 2 -- ft960315_1951_0420S001301H.fits 3 -- ft960315_1951_0420S001901H.fits 4 -- ft960315_1951_0420S002301H.fits 5 -- ft960315_1951_0420S003101H.fits 6 -- ft960315_1951_0420S003901H.fits 7 -- ft960315_1951_0420S005301H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s000201h.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S000201H.fits 2 -- ft960315_1951_0420S001401H.fits 3 -- ft960315_1951_0420S002401H.fits 4 -- ft960315_1951_0420S003201H.fits 5 -- ft960315_1951_0420S004001H.fits 6 -- ft960315_1951_0420S004201H.fits 7 -- ft960315_1951_0420S004401H.fits 8 -- ft960315_1951_0420S005401H.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S000201H.fits 2 -- ft960315_1951_0420S001401H.fits 3 -- ft960315_1951_0420S002401H.fits 4 -- ft960315_1951_0420S003201H.fits 5 -- ft960315_1951_0420S004001H.fits 6 -- ft960315_1951_0420S004201H.fits 7 -- ft960315_1951_0420S004401H.fits 8 -- ft960315_1951_0420S005401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s000302l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S002702L.fits 2 -- ft960315_1951_0420S003502L.fits 3 -- ft960315_1951_0420S003702L.fits 4 -- ft960315_1951_0420S004702L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S002702L.fits 2 -- ft960315_1951_0420S003502L.fits 3 -- ft960315_1951_0420S003702L.fits 4 -- ft960315_1951_0420S004702L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s000402m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S000802M.fits 2 -- ft960315_1951_0420S001102M.fits 3 -- ft960315_1951_0420S004802M.fits 4 -- ft960315_1951_0420S005102M.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S000802M.fits 2 -- ft960315_1951_0420S001102M.fits 3 -- ft960315_1951_0420S004802M.fits 4 -- ft960315_1951_0420S005102M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s000502l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S002602L.fits 2 -- ft960315_1951_0420S003402L.fits 3 -- ft960315_1951_0420S004602L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S002602L.fits 2 -- ft960315_1951_0420S003402L.fits 3 -- ft960315_1951_0420S004602L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960315_1951_0420S001501L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S001501L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S001501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000976 events
ft960315_1951_0420S001601L.fits ft960315_1951_0420S002001L.fits ft960315_1951_0420S002201L.fits ft960315_1951_0420S003801L.fits-> Ignoring the following files containing 000000379 events
ft960315_1951_0420S000702M.fits-> Ignoring the following files containing 000000064 events
ft960315_1951_0420S001201M.fits ft960315_1951_0420S005201M.fits-> Ignoring the following files containing 000000032 events
ft960315_1951_0420S004902M.fits-> Ignoring the following files containing 000000008 events
ft960315_1951_0420S002101L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 64 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 74 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 10 photon cnt = 269008 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 1 photon cnt = 84 SIS1SORTSPLIT:LO:s100501l.prelist merge count = 3 photon cnt = 848 SIS1SORTSPLIT:LO:s100601l.prelist merge count = 1 photon cnt = 1408 SIS1SORTSPLIT:LO:s100701l.prelist merge count = 1 photon cnt = 8 SIS1SORTSPLIT:LO:s100801m.prelist merge count = 2 photon cnt = 64 SIS1SORTSPLIT:LO:s100902l.prelist merge count = 4 photon cnt = 24281 SIS1SORTSPLIT:LO:s101002m.prelist merge count = 4 photon cnt = 21265 SIS1SORTSPLIT:LO:s101102m.prelist merge count = 1 photon cnt = 20 SIS1SORTSPLIT:LO:Total filenames split = 29 SIS1SORTSPLIT:LO:Total split file cnt = 11 SIS1SORTSPLIT:LO:End program-> Creating ad54000060s100101h.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S100101H.fits 2 -- ft960315_1951_0420S100501H.fits 3 -- ft960315_1951_0420S101401H.fits 4 -- ft960315_1951_0420S101601H.fits 5 -- ft960315_1951_0420S102001H.fits 6 -- ft960315_1951_0420S102601H.fits 7 -- ft960315_1951_0420S103201H.fits 8 -- ft960315_1951_0420S103401H.fits 9 -- ft960315_1951_0420S103601H.fits 10 -- ft960315_1951_0420S104401H.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S100101H.fits 2 -- ft960315_1951_0420S100501H.fits 3 -- ft960315_1951_0420S101401H.fits 4 -- ft960315_1951_0420S101601H.fits 5 -- ft960315_1951_0420S102001H.fits 6 -- ft960315_1951_0420S102601H.fits 7 -- ft960315_1951_0420S103201H.fits 8 -- ft960315_1951_0420S103401H.fits 9 -- ft960315_1951_0420S103601H.fits 10 -- ft960315_1951_0420S104401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s100202l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S102202L.fits 2 -- ft960315_1951_0420S102802L.fits 3 -- ft960315_1951_0420S103002L.fits 4 -- ft960315_1951_0420S103802L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S102202L.fits 2 -- ft960315_1951_0420S102802L.fits 3 -- ft960315_1951_0420S103002L.fits 4 -- ft960315_1951_0420S103802L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad54000060s100302m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S101002M.fits 2 -- ft960315_1951_0420S101202M.fits 3 -- ft960315_1951_0420S103902M.fits 4 -- ft960315_1951_0420S104202M.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S101002M.fits 2 -- ft960315_1951_0420S101202M.fits 3 -- ft960315_1951_0420S103902M.fits 4 -- ft960315_1951_0420S104202M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960315_1951_0420S101501L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960315_1951_0420S101501L.fits Merging binary extension #: 2 1 -- ft960315_1951_0420S101501L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000848 events
ft960315_1951_0420S101701L.fits ft960315_1951_0420S101901L.fits ft960315_1951_0420S103101L.fits-> Ignoring the following files containing 000000084 events
ft960315_1951_0420S100401H.fits-> Ignoring the following files containing 000000074 events
ft960315_1951_0420S100301H.fits-> Ignoring the following files containing 000000064 events
ft960315_1951_0420S101301M.fits ft960315_1951_0420S104301M.fits-> Ignoring the following files containing 000000064 events
ft960315_1951_0420S100201H.fits-> Ignoring the following files containing 000000020 events
ft960315_1951_0420S104002M.fits-> Ignoring the following files containing 000000008 events
ft960315_1951_0420S101801L.fits-> Tar-ing together the leftover raw files
a ft960315_1951_0420G200270H.fits 40K a ft960315_1951_0420G200570M.fits 40K a ft960315_1951_0420G200670M.fits 40K a ft960315_1951_0420G200770M.fits 40K a ft960315_1951_0420G200870M.fits 43K a ft960315_1951_0420G201070M.fits 40K a ft960315_1951_0420G201170M.fits 40K a ft960315_1951_0420G201570H.fits 40K a ft960315_1951_0420G201670H.fits 40K a ft960315_1951_0420G201870H.fits 40K a ft960315_1951_0420G202070H.fits 40K a ft960315_1951_0420G202270L.fits 43K a ft960315_1951_0420G203470H.fits 40K a ft960315_1951_0420G203870L.fits 40K a ft960315_1951_0420G204270H.fits 40K a ft960315_1951_0420G204470H.fits 40K a ft960315_1951_0420G204670L.fits 40K a ft960315_1951_0420G204870L.fits 40K a ft960315_1951_0420G205170H.fits 40K a ft960315_1951_0420G205370H.fits 40K a ft960315_1951_0420G205970L.fits 40K a ft960315_1951_0420G207570H.fits 40K a ft960315_1951_0420G207770L.fits 40K a ft960315_1951_0420G207970M.fits 40K a ft960315_1951_0420G208070M.fits 40K a ft960315_1951_0420G208170M.fits 40K a ft960315_1951_0420G300270H.fits 40K a ft960315_1951_0420G300570M.fits 40K a ft960315_1951_0420G300670M.fits 40K a ft960315_1951_0420G300770M.fits 40K a ft960315_1951_0420G300870M.fits 43K a ft960315_1951_0420G301070M.fits 40K a ft960315_1951_0420G301470H.fits 40K a ft960315_1951_0420G301670H.fits 40K a ft960315_1951_0420G301870L.fits 43K a ft960315_1951_0420G302970H.fits 40K a ft960315_1951_0420G303070H.fits 40K a ft960315_1951_0420G303170H.fits 40K a ft960315_1951_0420G303470L.fits 40K a ft960315_1951_0420G303970H.fits 40K a ft960315_1951_0420G304070H.fits 40K a ft960315_1951_0420G304270L.fits 43K a ft960315_1951_0420G304470L.fits 40K a ft960315_1951_0420G304870H.fits 40K a ft960315_1951_0420G304970H.fits 40K a ft960315_1951_0420G305570L.fits 40K a ft960315_1951_0420G305770L.fits 40K a ft960315_1951_0420G307170H.fits 40K a ft960315_1951_0420G307370L.fits 40K a ft960315_1951_0420G307570M.fits 40K a ft960315_1951_0420G307670M.fits 40K a ft960315_1951_0420G307770M.fits 40K a ft960315_1951_0420S000702M.fits 48K a ft960315_1951_0420S001201M.fits 40K a ft960315_1951_0420S001601L.fits 43K a ft960315_1951_0420S002001L.fits 68K a ft960315_1951_0420S002101L.fits 40K a ft960315_1951_0420S002201L.fits 40K a ft960315_1951_0420S003801L.fits 40K a ft960315_1951_0420S004902M.fits 40K a ft960315_1951_0420S005201M.fits 40K a ft960315_1951_0420S100201H.fits 40K a ft960315_1951_0420S100301H.fits 43K a ft960315_1951_0420S100401H.fits 43K a ft960315_1951_0420S101301M.fits 40K a ft960315_1951_0420S101701L.fits 68K a ft960315_1951_0420S101801L.fits 40K a ft960315_1951_0420S101901L.fits 40K a ft960315_1951_0420S103101L.fits 40K a ft960315_1951_0420S104002M.fits 40K a ft960315_1951_0420S104301M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft960315_1951.0420 'ft960315_1951.0420' is successfully opened Data Start Time is 101073068.95 (960315 195108) Time Margin 2.0 sec included Sync error detected in 42 th SF Sync error detected in 66 th SF Sync error detected in 97 th SF Sync error detected in 103 th SF Sync error detected in 107 th SF Sync error detected in 109 th SF Sync error detected in 110 th SF Sync error detected in 299 th SF Sync error detected in 303 th SF Sync error detected in 313 th SF Sync error detected in 316 th SF Sync error detected in 319 th SF Sync error detected in 363 th SF Sync error detected in 533 th SF Sync error detected in 1573 th SF Sync error detected in 1575 th SF Sync error detected in 1576 th SF Sync error detected in 1682 th SF Sync error detected in 1683 th SF Sync error detected in 1684 th SF Sync error detected in 1685 th SF 'ft960315_1951.0420' EOF detected, sf=7204 Data End Time is 101103658.85 (960316 042058) Gain History is written in ft960315_1951_0420.ghf-> Checking if column CAL_START in ft960315_1951_0420.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft960315_1951_0420.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad54000060g200270l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060g300270l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000502l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s000601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100202l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad54000060s100401l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 96/ 3/15 19:51 mjd=50157.827083 Orbit file name is ./frf.orbit.214 Epoch of Orbital Elements: 1996/3/11 12:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa960315_1951.0420 S0-HK file: ft960315_1951_0420S0HK.fits S1-HK file: ft960315_1951_0420S1HK.fits G2-HK file: ft960315_1951_0420G2HK.fits G3-HK file: ft960315_1951_0420G3HK.fits output FITS File: ft960315_1951_0420.mkf Total 957 Data bins were processed.-> Checking if column TIME in ft960315_1951_0420.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 8664.2586 The mean of the selected column is 39.204790 The standard deviation of the selected column is 9.0671059 The minimum of selected column is 23.812580 The maximum of selected column is 82.656532 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6958.5445 The mean of the selected column is 31.486627 The standard deviation of the selected column is 8.4552929 The minimum of selected column is 14.770884 The maximum of selected column is 66.312729 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10396.379 The mean of the selected column is 47.042439 The standard deviation of the selected column is 34.661100 The minimum of selected column is 16.156305 The maximum of selected column is 239.25081 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8073.0900 The mean of the selected column is 36.529819 The standard deviation of the selected column is 11.729994 The minimum of selected column is 17.812561 The maximum of selected column is 80.187775 The number of points used in calculation is 221-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>12 && S0_PIXL0<66.4 )&& (S0_PIXL1>6.1 && S0_PIXL1<56.8 )&& (S0_PIXL2>0.0 && S0_PIXL2<151 )&& (S0_PIXL3>1.3 && S0_PIXL3<71.7 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.95E+04 118974 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
88713 65785 0 22928 0 0
Writing events file
65785 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
88713 65785 0 22928 0 0
in 7049.44 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 65785
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 81 26495
Flickering pixels iter, pixels & cnts : 1 27 477
cleaning chip # 1
Hot pixels & counts : 44 13520
Flickering pixels iter, pixels & cnts : 1 20 419
cleaning chip # 2
Hot pixels & counts : 36 8822
Flickering pixels iter, pixels & cnts : 1 18 276
cleaning chip # 3
Hot pixels & counts : 45 12574
Flickering pixels iter, pixels & cnts : 1 17 275
Number of pixels rejected : 288
Number of (internal) image counts : 65785
Number of image cts rejected (N, %) : 62858 95.5506592
By chip : 0 1 2 3
Pixels rejected : 108 64 54 62
Image counts : 27638 15209 9604 13334
Image cts rejected: 26972 13939 9098 12849
Image cts rej (%) : 97.59 91.65 94.73 96.36
filtering data...
Total counts : 27638 15209 9604 13334
Total cts rejected: 26972 13939 9098 12849
Total cts rej (%) : 97.59 91.65 94.73 96.36
Number of clean counts accepted : 2927
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 288
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad54000060s000102h.evt use_events=no
Wrote cleaned events file to ad54000060s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad54000060s000112h.unf into ad54000060s000112h.evtThe sum of the selected column is 8664.2586 The mean of the selected column is 39.204790 The standard deviation of the selected column is 9.0671059 The minimum of selected column is 23.812580 The maximum of selected column is 82.656532 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6958.5445 The mean of the selected column is 31.486627 The standard deviation of the selected column is 8.4552929 The minimum of selected column is 14.770884 The maximum of selected column is 66.312729 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10396.379 The mean of the selected column is 47.042439 The standard deviation of the selected column is 34.661100 The minimum of selected column is 16.156305 The maximum of selected column is 239.25081 The number of points used in calculation is 221-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8073.0900 The mean of the selected column is 36.529819 The standard deviation of the selected column is 11.729994 The minimum of selected column is 17.812561 The maximum of selected column is 80.187775 The number of points used in calculation is 221-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>12 && S0_PIXL0<66.4 )&& (S0_PIXL1>6.1 && S0_PIXL1<56.8 )&& (S0_PIXL2>0.0 && S0_PIXL2<151 )&& (S0_PIXL3>1.3 && S0_PIXL3<71.7 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.95E+04 122512 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
99415 73691 0 25724 0 0
Writing events file
73691 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
99415 73691 0 25724 0 0
in 7049.44 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 73691
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 81 29271
Flickering pixels iter, pixels & cnts : 1 31 714
cleaning chip # 1
Hot pixels & counts : 46 15057
Flickering pixels iter, pixels & cnts : 1 19 452
cleaning chip # 2
Hot pixels & counts : 39 9962
Flickering pixels iter, pixels & cnts : 1 17 249
cleaning chip # 3
Hot pixels & counts : 48 14256
Flickering pixels iter, pixels & cnts : 1 21 282
Number of pixels rejected : 302
Number of (internal) image counts : 73691
Number of image cts rejected (N, %) : 70243 95.3209991
By chip : 0 1 2 3
Pixels rejected : 112 65 56 69
Image counts : 30788 16958 10809 15136
Image cts rejected: 29985 15509 10211 14538
Image cts rej (%) : 97.39 91.46 94.47 96.05
filtering data...
Total counts : 30788 16958 10809 15136
Total cts rejected: 29985 15509 10211 14538
Total cts rej (%) : 97.39 91.46 94.47 96.05
Number of clean counts accepted : 3448
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 302
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad54000060s000112h.evt use_events=no
Wrote cleaned events file to ad54000060s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad54000060s000201h.unf because of modeThe sum of the selected column is 907.09686 The mean of the selected column is 69.776682 The standard deviation of the selected column is 20.766570 The minimum of selected column is 45.937660 The maximum of selected column is 115.03164 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 703.25241 The mean of the selected column is 54.096339 The standard deviation of the selected column is 15.104011 The minimum of selected column is 31.718859 The maximum of selected column is 90.594055 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1074.9412 The mean of the selected column is 82.687784 The standard deviation of the selected column is 28.881313 The minimum of selected column is 52.406429 The maximum of selected column is 143.12549 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 889.26347 The mean of the selected column is 68.404882 The standard deviation of the selected column is 26.816468 The minimum of selected column is 33.750118 The maximum of selected column is 129.31294 The number of points used in calculation is 13-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>7.4 && S0_PIXL0<132 )&& (S0_PIXL1>8.7 && S0_PIXL1<99.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<169.3 )&& (S0_PIXL3>0.0 && S0_PIXL3<148.8 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.25E+04 22234 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
12730 4341 0 8389 0 0
Writing events file
4341 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12730 4341 0 8389 0 0
in 394.23 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 4341
Total counts in chip images : 4340
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 65 1533
Flickering pixels iter, pixels & cnts : 1 36 276
cleaning chip # 1
Hot pixels & counts : 38 736
Flickering pixels iter, pixels & cnts : 1 14 77
cleaning chip # 2
Hot pixels & counts : 27 439
Flickering pixels iter, pixels & cnts : 1 12 57
cleaning chip # 3
Hot pixels & counts : 42 893
Flickering pixels iter, pixels & cnts : 1 14 87
Number of pixels rejected : 248
Number of (internal) image counts : 4340
Number of image cts rejected (N, %) : 4098 94.4239655
By chip : 0 1 2 3
Pixels rejected : 101 52 39 56
Image counts : 1864 897 539 1040
Image cts rejected: 1809 813 496 980
Image cts rej (%) : 97.05 90.64 92.02 94.23
filtering data...
Total counts : 1865 897 539 1040
Total cts rejected: 1810 813 496 980
Total cts rej (%) : 97.05 90.64 92.02 94.23
Number of clean counts accepted : 242
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 248
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad54000060s000202h.evt use_events=no
Wrote cleaned events file to ad54000060s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad54000060s000212h.unf into ad54000060s000212h.evtThe sum of the selected column is 907.09686 The mean of the selected column is 69.776682 The standard deviation of the selected column is 20.766570 The minimum of selected column is 45.937660 The maximum of selected column is 115.03164 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 703.25241 The mean of the selected column is 54.096339 The standard deviation of the selected column is 15.104011 The minimum of selected column is 31.718859 The maximum of selected column is 90.594055 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1074.9412 The mean of the selected column is 82.687784 The standard deviation of the selected column is 28.881313 The minimum of selected column is 52.406429 The maximum of selected column is 143.12549 The number of points used in calculation is 13-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 889.26347 The mean of the selected column is 68.404882 The standard deviation of the selected column is 26.816468 The minimum of selected column is 33.750118 The maximum of selected column is 129.31294 The number of points used in calculation is 13-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>7.4 && S0_PIXL0<132 )&& (S0_PIXL1>8.7 && S0_PIXL1<99.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<169.3 )&& (S0_PIXL3>0.0 && S0_PIXL3<148.8 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 20:02:40 0.25E+04 26571 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
16500 4999 0 11501 0 0
Writing events file
4999 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16500 4999 0 11501 0 0
in 394.23 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 4999
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 1836
Flickering pixels iter, pixels & cnts : 1 32 244
cleaning chip # 1
Hot pixels & counts : 43 848
Flickering pixels iter, pixels & cnts : 1 14 78
cleaning chip # 2
Hot pixels & counts : 32 546
Flickering pixels iter, pixels & cnts : 1 13 62
cleaning chip # 3
Hot pixels & counts : 46 1022
Flickering pixels iter, pixels & cnts : 1 13 87
Number of pixels rejected : 267
Number of (internal) image counts : 4999
Number of image cts rejected (N, %) : 4723 94.4788971
By chip : 0 1 2 3
Pixels rejected : 106 57 45 59
Image counts : 2149 1017 659 1174
Image cts rejected: 2080 926 608 1109
Image cts rej (%) : 96.79 91.05 92.26 94.46
filtering data...
Total counts : 2149 1017 659 1174
Total cts rejected: 2080 926 608 1109
Total cts rej (%) : 96.79 91.05 92.26 94.46
Number of clean counts accepted : 276
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 267
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad54000060s000212h.evt use_events=no
Wrote cleaned events file to ad54000060s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad54000060s000302l.unf into ad54000060s000302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:42:32 0.28E+04 20504 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad54000060s000302l.evt use_events=no
Wrote cleaned events file to ad54000060s000302l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad54000060s000302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.14E+04 15538 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
11460 34 0 11426 0 0
Writing events file
34 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11460 34 0 11426 0 0
in 5.65 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 34
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 34
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 34 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 34 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 34
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad54000060s000402m.evt use_events=no
Wrote cleaned events file to ad54000060s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad54000060s000502l.unf into ad54000060s000502l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:20:08 0.31E+04 1441 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s000502l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad54000060s000502l.evt use_events=no
Wrote cleaned events file to ad54000060s000502l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad54000060s000502l.evt since it contains 0 eventsThe sum of the selected column is 9989.4715 The mean of the selected column is 42.873268 The standard deviation of the selected column is 12.295640 The minimum of selected column is 20.375069 The maximum of selected column is 109.18787 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10512.473 The mean of the selected column is 45.117911 The standard deviation of the selected column is 12.286458 The minimum of selected column is 17.406309 The maximum of selected column is 99.937836 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10250.024 The mean of the selected column is 43.991521 The standard deviation of the selected column is 14.326445 The minimum of selected column is 23.312580 The maximum of selected column is 106.37536 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9917.6796 The mean of the selected column is 42.565148 The standard deviation of the selected column is 11.894910 The minimum of selected column is 18.875065 The maximum of selected column is 88.750298 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>5.9 && S1_PIXL0<79.7 )&& (S1_PIXL1>8.2 && S1_PIXL1<81.9 )&& (S1_PIXL2>1 && S1_PIXL2<86.9 )&& (S1_PIXL3>6.8 && S1_PIXL3<78.2 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.12E+05 191946 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
135669 87668 0 48001 0 0
Writing events file
87668 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
135669 87668 0 48001 0 0
in 7623.30 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 87668
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 60 21973
Flickering pixels iter, pixels & cnts : 1 27 555
Flickering pixels iter, pixels & cnts : 2 1 3
cleaning chip # 1
Hot pixels & counts : 68 20487
Flickering pixels iter, pixels & cnts : 1 25 574
cleaning chip # 2
Hot pixels & counts : 65 23566
Flickering pixels iter, pixels & cnts : 1 36 1074
cleaning chip # 3
Hot pixels & counts : 53 15796
Flickering pixels iter, pixels & cnts : 1 22 406
Number of pixels rejected : 357
Number of (internal) image counts : 87668
Number of image cts rejected (N, %) : 84434 96.3110809
By chip : 0 1 2 3
Pixels rejected : 88 93 101 75
Image counts : 23019 21718 25559 17372
Image cts rejected: 22531 21061 24640 16202
Image cts rej (%) : 97.88 96.97 96.40 93.27
filtering data...
Total counts : 23019 21718 25559 17372
Total cts rejected: 22531 21061 24640 16202
Total cts rej (%) : 97.88 96.97 96.40 93.27
Number of clean counts accepted : 3234
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 357
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad54000060s100102h.evt use_events=no
Wrote cleaned events file to ad54000060s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad54000060s100112h.unf into ad54000060s100112h.evtThe sum of the selected column is 9989.4715 The mean of the selected column is 42.873268 The standard deviation of the selected column is 12.295640 The minimum of selected column is 20.375069 The maximum of selected column is 109.18787 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10512.473 The mean of the selected column is 45.117911 The standard deviation of the selected column is 12.286458 The minimum of selected column is 17.406309 The maximum of selected column is 99.937836 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10250.024 The mean of the selected column is 43.991521 The standard deviation of the selected column is 14.326445 The minimum of selected column is 23.312580 The maximum of selected column is 106.37536 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9917.6796 The mean of the selected column is 42.565148 The standard deviation of the selected column is 11.894910 The minimum of selected column is 18.875065 The maximum of selected column is 88.750298 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>5.9 && S1_PIXL0<79.7 )&& (S1_PIXL1>8.2 && S1_PIXL1<81.9 )&& (S1_PIXL2>1 && S1_PIXL2<86.9 )&& (S1_PIXL3>6.8 && S1_PIXL3<78.2 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.12E+05 203036 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
167290 106620 0 60670 0 0
Writing events file
106620 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
167290 106620 0 60670 0 0
in 7623.30 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 106620
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 66 25999
Flickering pixels iter, pixels & cnts : 1 24 541
cleaning chip # 1
Hot pixels & counts : 74 25634
Flickering pixels iter, pixels & cnts : 1 29 650
cleaning chip # 2
Hot pixels & counts : 73 27931
Flickering pixels iter, pixels & cnts : 1 28 780
cleaning chip # 3
Hot pixels & counts : 57 20543
Flickering pixels iter, pixels & cnts : 1 23 422
Number of pixels rejected : 374
Number of (internal) image counts : 106620
Number of image cts rejected (N, %) : 102500 96.1358109
By chip : 0 1 2 3
Pixels rejected : 90 103 101 80
Image counts : 27173 27118 29831 22498
Image cts rejected: 26540 26284 28711 20965
Image cts rej (%) : 97.67 96.92 96.25 93.19
filtering data...
Total counts : 27173 27118 29831 22498
Total cts rejected: 26540 26284 28711 20965
Total cts rej (%) : 97.67 96.92 96.25 93.19
Number of clean counts accepted : 4120
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 374
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad54000060s100112h.evt use_events=no
Wrote cleaned events file to ad54000060s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad54000060s100202l.unf into ad54000060s100202l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:20:08 0.59E+04 24281 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s100202l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s100202l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad54000060s100202l.evt use_events=no
Wrote cleaned events file to ad54000060s100202l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad54000060s100202l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.17E+04 21265 1111
Processing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
14779 47 0 14732 0 0
Writing events file
47 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14779 47 0 14732 0 0
in 5.65 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/54000060.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/54000060.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 47
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 47
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 47 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 47 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 47
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad54000060s100302m.evt use_events=no
Wrote cleaned events file to ad54000060s100302m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad54000060s100401l.unf because of mode(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 24412 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.unf
Total Good Bad: Region Time Phase Cut
24412 12641 9383 2388 0 0
Writing events file
12641 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24412 12641 9383 2388 0 0
in 9314.28 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
12641 12214 427
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad54000060g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 12214 in ad54000060g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 4032 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/ad54000060g200270l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad54000060g200270l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad54000060g200270l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 25226 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.unf
Total Good Bad: Region Time Phase Cut
25226 14476 7960 2790 0 0
Writing events file
14476 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25226 14476 7960 2790 0 0
in 9320.28 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
14476 13979 497
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad54000060g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 13979 in ad54000060g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 3731 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/ad54000060g300270l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!screen:ASCA > read events ad54000060g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad54000060g300270l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad54000060g300270l.evt since it contains 0 events-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad54000060g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1574
Mean RA/DEC/ROLL : 263.4075 -33.0205 267.1574
Pnt RA/DEC/ROLL : 263.4268 -32.9768 267.1574
Image rebin factor : 1
Attitude Records : 28678
GTI intervals : 34
Total GTI (secs) : 9314.277
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1530.4960938 1530.4960938
20 Percent Complete: Total/live time: 2692.0151367 2692.0151367
30 Percent Complete: Total/live time: 4532.0498047 4532.0498047
40 Percent Complete: Total/live time: 4532.0498047 4532.0498047
50 Percent Complete: Total/live time: 6438.1049805 6438.1049805
60 Percent Complete: Total/live time: 6438.1049805 6438.1049805
70 Percent Complete: Total/live time: 7934.1811523 7934.1811523
80 Percent Complete: Total/live time: 7934.1811523 7934.1811523
90 Percent Complete: Total/live time: 8673.1787109 8673.1787109
100 Percent Complete: Total/live time: 9314.2773438 9314.2773438
Number of attitude steps used: 19
Number of attitude steps avail: 24157
Mean RA/DEC pixel offset: -9.4894 -2.6989
writing expo file: ad54000060g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 12214 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 12031 183 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 12031 183 0 0 0
in 9314.28 seconds
Image has 12031 counts for 1.292 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 3785 183 0 0 8246
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 3785 183 0 0 8246
in 9314.28 seconds
Image has 3785 counts for 0.4064 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 8286 183 0 0 3745
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 8286 183 0 0 3745
in 9314.28 seconds
Image has 8286 counts for 0.8896 counts/sec
Command not found; type ? for a command listing
!ad54000060g200170h:ASCA >
!ad54000060g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060g200170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060g200170h:ASCA > read events ad54000060g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060g200170h:ASCA-GIS2-PH > set image sky
!ad54000060g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad54000060g200170h:ASCA-GIS2-PH > extract image
!ad54000060g200170h:ASCA-GIS2-PH > save image outfile=ad54000060g200170h.img
Wrote image to file ad54000060g200170h.img
!ad54000060g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad54000060g200170h:ASCA-GIS2-PH > extract image
!ad54000060g200170h:ASCA-GIS2-PH > save image outfile=ad54000060g200170h_lo.img
Wrote image to file ad54000060g200170h_lo.img
!ad54000060g200170h:ASCA-GIS2-PH > clear pha_cut
!ad54000060g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad54000060g200170h:ASCA-GIS2-PH > extract image
!ad54000060g200170h:ASCA-GIS2-PH > save image outfile=ad54000060g200170h_hi.img
Wrote image to file ad54000060g200170h_hi.img
!ad54000060g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad54000060g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad54000060g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1551
Mean RA/DEC/ROLL : 263.4119 -32.9959 267.1551
Pnt RA/DEC/ROLL : 263.4225 -33.0014 267.1551
Image rebin factor : 1
Attitude Records : 28678
GTI intervals : 32
Total GTI (secs) : 9320.277
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1536.4960938 1536.4960938
20 Percent Complete: Total/live time: 2698.0151367 2698.0151367
30 Percent Complete: Total/live time: 4538.0498047 4538.0498047
40 Percent Complete: Total/live time: 4538.0498047 4538.0498047
50 Percent Complete: Total/live time: 6444.1049805 6444.1049805
60 Percent Complete: Total/live time: 6444.1049805 6444.1049805
70 Percent Complete: Total/live time: 7940.1811523 7940.1811523
80 Percent Complete: Total/live time: 7940.1811523 7940.1811523
90 Percent Complete: Total/live time: 8679.1787109 8679.1787109
100 Percent Complete: Total/live time: 9320.2773438 9320.2773438
Number of attitude steps used: 19
Number of attitude steps avail: 24157
Mean RA/DEC pixel offset: 1.9535 -1.5621
writing expo file: ad54000060g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 13979 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 13763 216 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 13763 216 0 0 0
in 9320.28 seconds
Image has 13763 counts for 1.477 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 4035 216 0 0 9728
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 4035 216 0 0 9728
in 9320.28 seconds
Image has 4035 counts for 0.4329 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 9777 216 0 0 3986
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 9777 216 0 0 3986
in 9320.28 seconds
Image has 9777 counts for 1.049 counts/sec
Command not found; type ? for a command listing
!ad54000060g300170h:ASCA >
!ad54000060g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060g300170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060g300170h:ASCA > read events ad54000060g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060g300170h:ASCA-GIS3-PH > set image sky
!ad54000060g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad54000060g300170h:ASCA-GIS3-PH > extract image
!ad54000060g300170h:ASCA-GIS3-PH > save image outfile=ad54000060g300170h.img
Wrote image to file ad54000060g300170h.img
!ad54000060g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad54000060g300170h:ASCA-GIS3-PH > extract image
!ad54000060g300170h:ASCA-GIS3-PH > save image outfile=ad54000060g300170h_lo.img
Wrote image to file ad54000060g300170h_lo.img
!ad54000060g300170h:ASCA-GIS3-PH > clear pha_cut
!ad54000060g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad54000060g300170h:ASCA-GIS3-PH > extract image
!ad54000060g300170h:ASCA-GIS3-PH > save image outfile=ad54000060g300170h_hi.img
Wrote image to file ad54000060g300170h_hi.img
!ad54000060g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad54000060s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad54000060s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1661
Mean RA/DEC/ROLL : 263.3914 -33.0074 267.1661
Pnt RA/DEC/ROLL : 263.4444 -32.9881 267.1661
Image rebin factor : 4
Attitude Records : 28678
Hot Pixels : 288
GTI intervals : 21
Total GTI (secs) : 7049.437
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1903.7496338 1903.7496338
20 Percent Complete: Total/live time: 1903.7496338 1903.7496338
30 Percent Complete: Total/live time: 3311.7495117 3311.7495117
40 Percent Complete: Total/live time: 3311.7495117 3311.7495117
50 Percent Complete: Total/live time: 5470.5795898 5470.5795898
60 Percent Complete: Total/live time: 5470.5795898 5470.5795898
70 Percent Complete: Total/live time: 5929.4360352 5929.4360352
80 Percent Complete: Total/live time: 5929.4360352 5929.4360352
90 Percent Complete: Total/live time: 7049.4360352 7049.4360352
100 Percent Complete: Total/live time: 7049.4360352 7049.4360352
Number of attitude steps used: 14
Number of attitude steps avail: 20390
Mean RA/DEC pixel offset: -36.6878 -86.2715
writing expo file: ad54000060s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 2927 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2927 2927 0 0 0 0
in 7049.44 seconds
Image has 2927 counts for 0.4152 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 955 0 0 0 1972
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2927 955 0 0 0 1972
in 7049.44 seconds
Image has 955 counts for 0.1355 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 1975 0 0 0 952
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2927 1975 0 0 0 952
in 7049.44 seconds
Image has 1975 counts for 0.2802 counts/sec
Command not found; type ? for a command listing
!ad54000060s000102h:ASCA >
!ad54000060s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060s000102h:ASCA > read events ad54000060s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad54000060s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad54000060s000102h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000102h.img
Wrote image to file ad54000060s000102h.img
!ad54000060s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad54000060s000102h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000102h_lo.img
Wrote image to file ad54000060s000102h_lo.img
!ad54000060s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad54000060s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad54000060s000102h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000102h_hi.img
Wrote image to file ad54000060s000102h_hi.img
!ad54000060s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad54000060s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad54000060s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1661
Mean RA/DEC/ROLL : 263.3918 -33.0070 267.1661
Pnt RA/DEC/ROLL : 263.4419 -32.9890 267.1661
Image rebin factor : 4
Attitude Records : 28678
Hot Pixels : 248
GTI intervals : 6
Total GTI (secs) : 394.231
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 68.0218506 68.0218506
20 Percent Complete: Total/live time: 132.0218506 132.0218506
30 Percent Complete: Total/live time: 132.0218506 132.0218506
40 Percent Complete: Total/live time: 200.0825806 200.0825806
50 Percent Complete: Total/live time: 310.1312256 310.1312256
60 Percent Complete: Total/live time: 310.1312256 310.1312256
70 Percent Complete: Total/live time: 310.6311340 310.6311340
80 Percent Complete: Total/live time: 394.2308350 394.2308350
100 Percent Complete: Total/live time: 394.2308350 394.2308350
Number of attitude steps used: 7
Number of attitude steps avail: 5631
Mean RA/DEC pixel offset: -31.8392 -81.9099
writing expo file: ad54000060s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.39E+03 242 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.evt
Total Good Bad: Region Time Phase Cut
242 242 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
242 242 0 0 0 0
in 394.23 seconds
Image has 242 counts for 0.6139 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.evt
Total Good Bad: Region Time Phase Cut
242 142 0 0 0 100
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
242 142 0 0 0 100
in 394.23 seconds
Image has 142 counts for 0.3602 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.evt
Total Good Bad: Region Time Phase Cut
242 100 0 0 0 142
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
242 100 0 0 0 142
in 394.23 seconds
Image has 100 counts for 0.2537 counts/sec
Command not found; type ? for a command listing
!ad54000060s000202h:ASCA >
!ad54000060s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060s000202h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060s000202h:ASCA > read events ad54000060s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad54000060s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad54000060s000202h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000202h.img
Wrote image to file ad54000060s000202h.img
!ad54000060s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad54000060s000202h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000202h_lo.img
Wrote image to file ad54000060s000202h_lo.img
!ad54000060s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad54000060s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad54000060s000202h:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000202h_hi.img
Wrote image to file ad54000060s000202h_hi.img
!ad54000060s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad54000060s000402m.expo
ASCAEXPO_V0.9b
reading data file: ad54000060s000402m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1658
Mean RA/DEC/ROLL : 263.3920 -33.0090 267.1658
Pnt RA/DEC/ROLL : 263.4426 -32.9887 267.1658
Image rebin factor : 4
Attitude Records : 28678
Hot Pixels : 0
GTI intervals : 1
Total GTI (secs) : 5.654
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 0.9043053 0.9043053
20 Percent Complete: Total/live time: 5.6543431 5.6543431
100 Percent Complete: Total/live time: 5.6543431 5.6543431
Number of attitude steps used: 2
Number of attitude steps avail: 110
Mean RA/DEC pixel offset: -21.7379 -49.7461
writing expo file: ad54000060s000402m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060s000402m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060s000402m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.57E+01 34 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 34 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34 34 0 0 0 0
in 5.65 seconds
Image has 34 counts for 6.013 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 30 0 0 0 4
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34 30 0 0 0 4
in 5.65 seconds
Image has 30 counts for 5.306 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 4 0 0 0 30
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34 4 0 0 0 30
in 5.65 seconds
Image has 4 counts for 0.7074 counts/sec
Command not found; type ? for a command listing
!ad54000060s000402m:ASCA >
!ad54000060s000402m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060s000402m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060s000402m:ASCA > read events ad54000060s000402m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060s000402m:ASCA-SIS0-BRIGHT > set image sky
!ad54000060s000402m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad54000060s000402m:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000402m.img
Wrote image to file ad54000060s000402m.img
!ad54000060s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad54000060s000402m:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000402m_lo.img
Wrote image to file ad54000060s000402m_lo.img
!ad54000060s000402m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad54000060s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad54000060s000402m:ASCA-SIS0-BRIGHT > extract image
!ad54000060s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad54000060s000402m_hi.img
Wrote image to file ad54000060s000402m_hi.img
!ad54000060s000402m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad54000060s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad54000060s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1559
Mean RA/DEC/ROLL : 263.4103 -33.0091 267.1559
Pnt RA/DEC/ROLL : 263.4256 -32.9863 267.1559
Image rebin factor : 4
Attitude Records : 28678
Hot Pixels : 357
GTI intervals : 39
Total GTI (secs) : 7623.297
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2009.4696045 2009.4696045
20 Percent Complete: Total/live time: 2009.4696045 2009.4696045
30 Percent Complete: Total/live time: 3607.4384766 3607.4384766
40 Percent Complete: Total/live time: 3607.4384766 3607.4384766
50 Percent Complete: Total/live time: 5143.4384766 5143.4384766
60 Percent Complete: Total/live time: 5143.4384766 5143.4384766
70 Percent Complete: Total/live time: 6471.2968750 6471.2968750
80 Percent Complete: Total/live time: 6471.2968750 6471.2968750
90 Percent Complete: Total/live time: 7270.1982422 7270.1982422
100 Percent Complete: Total/live time: 7623.2968750 7623.2968750
Number of attitude steps used: 15
Number of attitude steps avail: 21428
Mean RA/DEC pixel offset: -41.1222 -19.6344
writing expo file: ad54000060s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 3234 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3234 3234 0 0 0 0
in 7623.30 seconds
Image has 3234 counts for 0.4242 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 1043 0 0 0 2191
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3234 1043 0 0 0 2191
in 7623.30 seconds
Image has 1043 counts for 0.1368 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 2199 0 0 0 1035
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3234 2199 0 0 0 1035
in 7623.30 seconds
Image has 2199 counts for 0.2885 counts/sec
Command not found; type ? for a command listing
!ad54000060s100102h:ASCA >
!ad54000060s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060s100102h:ASCA > read events ad54000060s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad54000060s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad54000060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100102h.img
Wrote image to file ad54000060s100102h.img
!ad54000060s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad54000060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100102h_lo.img
Wrote image to file ad54000060s100102h_lo.img
!ad54000060s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad54000060s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad54000060s100102h:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100102h_hi.img
Wrote image to file ad54000060s100102h_hi.img
!ad54000060s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad54000060s100302m.expo
ASCAEXPO_V0.9b
reading data file: ad54000060s100302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960315_1951.0420
making an exposure map...
Aspect RA/DEC/ROLL : 263.4170 -32.9996 267.1556
Mean RA/DEC/ROLL : 263.4108 -33.0109 267.1556
Pnt RA/DEC/ROLL : 263.4240 -32.9869 267.1556
Image rebin factor : 4
Attitude Records : 28678
Hot Pixels : 0
GTI intervals : 1
Total GTI (secs) : 5.654
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 0.9043053 0.9043053
20 Percent Complete: Total/live time: 5.6543431 5.6543431
100 Percent Complete: Total/live time: 5.6543431 5.6543431
Number of attitude steps used: 2
Number of attitude steps avail: 110
Mean RA/DEC pixel offset: -23.9600 -13.8205
writing expo file: ad54000060s100302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad54000060s100302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad54000060s100302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.57E+01 47 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 47 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
47 47 0 0 0 0
in 5.65 seconds
Image has 47 counts for 8.312 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 45 0 0 0 2
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
47 45 0 0 0 2
in 5.65 seconds
Image has 45 counts for 7.958 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 2 0 0 0 45
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
47 2 0 0 0 45
in 5.65 seconds
Image has 2 counts for 0.3537 counts/sec
Command not found; type ? for a command listing
!ad54000060s100302m:ASCA >
!ad54000060s100302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad54000060s100302m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!ad54000060s100302m:ASCA > read events ad54000060s100302m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!ad54000060s100302m:ASCA-SIS1-BRIGHT > set image sky
!ad54000060s100302m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad54000060s100302m:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100302m.img
Wrote image to file ad54000060s100302m.img
!ad54000060s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad54000060s100302m:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100302m_lo.img
Wrote image to file ad54000060s100302m_lo.img
!ad54000060s100302m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad54000060s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad54000060s100302m:ASCA-SIS1-BRIGHT > extract image
!ad54000060s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad54000060s100302m_hi.img
Wrote image to file ad54000060s100302m_hi.img
!ad54000060s100302m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad54000060s000102h.expo ad54000060s000202h.expo ad54000060s000402m.expo ad54000060s100102h.expo ad54000060s100302m.expo-> Summing the following images to produce ad54000060sis32002_all.totsky
ad54000060s000102h.img ad54000060s000202h.img ad54000060s000402m.img ad54000060s100102h.img ad54000060s100302m.img-> Summing the following images to produce ad54000060sis32002_lo.totsky
ad54000060s000102h_lo.img ad54000060s000202h_lo.img ad54000060s000402m_lo.img ad54000060s100102h_lo.img ad54000060s100302m_lo.img-> Summing the following images to produce ad54000060sis32002_hi.totsky
ad54000060s000102h_hi.img ad54000060s000202h_hi.img ad54000060s000402m_hi.img ad54000060s100102h_hi.img ad54000060s100302m_hi.img-> Running XIMAGE to create ad54000060sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad54000060sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 5.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 5 min: 0 ![2]XIMAGE> read/exp_map ad54000060sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 251.305 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 251 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 22231 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 27.0000 27 0 ![9]XIMAGE> exit-> Summing gis images
ad54000060g200170h.expo ad54000060g300170h.expo-> Summing the following images to produce ad54000060gis25670_all.totsky
ad54000060g200170h.img ad54000060g300170h.img-> Summing the following images to produce ad54000060gis25670_lo.totsky
ad54000060g200170h_lo.img ad54000060g300170h_lo.img-> Summing the following images to produce ad54000060gis25670_hi.totsky
ad54000060g200170h_hi.img ad54000060g300170h_hi.img-> Running XIMAGE to create ad54000060gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad54000060gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 10.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 10 min: 0 ![2]XIMAGE> read/exp_map ad54000060gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 310.576 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 310 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 13.0000 13 0 ![9]XIMAGE> exit
187 66 0.000309233 178 75 8.54604-> Smoothing ad54000060gis25670_hi.totsky with ad54000060gis25670.totexpo
188 67 0.000264615 25 26 13.2024 126 46 0.000178798 39 40 11.4637-> Smoothing ad54000060gis25670_lo.totsky with ad54000060gis25670.totexpo
149 47 7.72098e-05 176 51 6.27083-> Determining extraction radii
187 66 75 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad54000060gis25670.src
260 90 3.74155e-05 284 139 8.42422-> Smoothing ad54000060sis32002_hi.totsky with ad54000060sis32002.totexpo
228 77 2.55163e-05 268 141 10.6862-> Smoothing ad54000060sis32002_lo.totsky with ad54000060sis32002.totexpo
260 90 139 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad54000060sis32002.src
The sum of the selected column is 97512.000 The mean of the selected column is 329.43243 The standard deviation of the selected column is 62.540039 The minimum of selected column is 216.00000 The maximum of selected column is 458.00000 The number of points used in calculation is 296-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 79952.000 The mean of the selected column is 270.10811 The standard deviation of the selected column is 39.460881 The minimum of selected column is 207.00000 The maximum of selected column is 345.00000 The number of points used in calculation is 296-> Converting (1040.0,360.0,2.0) to s1 detector coordinates
The sum of the selected column is 107002.00 The mean of the selected column is 331.27554 The standard deviation of the selected column is 61.995203 The minimum of selected column is 217.00000 The maximum of selected column is 456.00000 The number of points used in calculation is 323-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 93356.000 The mean of the selected column is 289.02786 The standard deviation of the selected column is 50.016542 The minimum of selected column is 210.00000 The maximum of selected column is 384.00000 The number of points used in calculation is 323-> Converting (187.0,66.0,2.0) to g2 detector coordinates
The sum of the selected column is 464417.00 The mean of the selected column is 80.627951 The standard deviation of the selected column is 22.098973 The minimum of selected column is 41.000000 The maximum of selected column is 132.00000 The number of points used in calculation is 5760-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 602546.00 The mean of the selected column is 104.60868 The standard deviation of the selected column is 22.748411 The minimum of selected column is 42.000000 The maximum of selected column is 147.00000 The number of points used in calculation is 5760-> Converting (187.0,66.0,2.0) to g3 detector coordinates
The sum of the selected column is 1348.0000 The mean of the selected column is 64.190476 The standard deviation of the selected column is 1.4703417 The minimum of selected column is 62.000000 The maximum of selected column is 67.000000 The number of points used in calculation is 21-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1541.0000 The mean of the selected column is 73.380952 The standard deviation of the selected column is 1.1169687 The minimum of selected column is 71.000000 The maximum of selected column is 75.000000 The number of points used in calculation is 21
1 ad54000060s000102h.evt 2961 1 ad54000060s000402m.evt 2961 2 ad54000060s000202h.evt 242-> Fetching SIS0_OFFCHIP.1
ad54000060s000102h.evt ad54000060s000402m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
2 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.57E+01 34 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 1821 1106 0 0 0
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 32 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2961 1853 1108 0 0 0
in 7055.09 seconds
Spectrum has 1853 counts for 0.2626 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7055.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.19879 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 1821 1106 0 0 0
Writing events file
1821 events written to the output file
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 32 2 0 0 0
Writing events file
1853 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2961 1853 1108 0 0 0
in 7055.09 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad54000060s000402m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad54000060s010102_1.pi group=yes
Wrote spectrum to ad54000060s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad54000060s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7055.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.19879 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 30 are grouped by a factor 15 ... 31 - 40 are grouped by a factor 5 ... 41 - 48 are grouped by a factor 4 ... 49 - 51 are grouped by a factor 3 ... 52 - 55 are grouped by a factor 4 ... 56 - 67 are grouped by a factor 3 ... 68 - 71 are grouped by a factor 4 ... 72 - 80 are grouped by a factor 3 ... 81 - 84 are grouped by a factor 4 ... 85 - 89 are grouped by a factor 5 ... 90 - 92 are grouped by a factor 3 ... 93 - 104 are grouped by a factor 4 ... 105 - 107 are grouped by a factor 3 ... 108 - 112 are grouped by a factor 5 ... 113 - 115 are grouped by a factor 3 ... 116 - 127 are grouped by a factor 4 ... 128 - 133 are grouped by a factor 6 ... 134 - 138 are grouped by a factor 5 ... 139 - 142 are grouped by a factor 4 ... 143 - 160 are grouped by a factor 6 ... 161 - 167 are grouped by a factor 7 ... 168 - 175 are grouped by a factor 8 ... 176 - 184 are grouped by a factor 9 ... 185 - 197 are grouped by a factor 13 ... 198 - 208 are grouped by a factor 11 ... 209 - 232 are grouped by a factor 24 ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.71E+04 1853 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1853 288 1565 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1853 288 1565 0 0 0
in 7055.09 seconds
Spectrum has 288 counts for 4.0822E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7055.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.90918E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.71E+04 1853 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1853 1275 578 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1853 1275 578 0 0 0
in 7055.09 seconds
Spectrum has 1275 counts for 0.1807 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7055.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.10462 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.71E+04 1853 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1853 271 1582 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1853 271 1582 0 0 0
in 7055.09 seconds
Spectrum has 271 counts for 3.8412E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7055.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.28223E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.71E+04 1853 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1853 19 1834 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1853 19 1834 0 0 0
in 7055.09 seconds
Spectrum has 19 counts for 2.6931E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7055.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.25586E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.155423637344846 rmf1.tmp 0.688073394495413 rmf2.tmp 0.146249325418241 rmf3.tmp 0.0102536427415003-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.554E-01 * rmf0.tmp
6.881E-01 * rmf1.tmp
1.462E-01 * rmf2.tmp
1.025E-02 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.16
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.69
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.15
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.01
ASCA SIS0 NONE NONE PI
-> Generating ad54000060s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 84 by 79 bins
expanded to 84 by 79 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 229.07 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.81400E+03
Weighted mean angle from optical axis = 8.116 arcmin
-> Standard Output From STOOL group_event_files:1 ad54000060s000112h.evt 3448 2 ad54000060s000212h.evt 276-> SIS0_OFFCHIP.1 already present in current directory
ad54000060s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 3448 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000112h.evt
Total Good Bad: Region Time Phase Cut
3448 2105 1343 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3448 2105 1343 0 0 0
in 7049.44 seconds
Spectrum has 2105 counts for 0.2986 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7049.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.19879 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060s010212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000112h.evt
Total Good Bad: Region Time Phase Cut
3448 2105 1343 0 0 0
Writing events file
2105 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3448 2105 1343 0 0 0
in 7049.44 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad54000060s010212_1.pi group=yes
Wrote spectrum to ad54000060s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad54000060s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7049.4 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.19879 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 57 are grouped by a factor 26 ... 58 - 70 are grouped by a factor 13 ... 71 - 80 are grouped by a factor 10 ... 81 - 87 are grouped by a factor 7 ... 88 - 95 are grouped by a factor 8 ... 96 - 99 are grouped by a factor 4 ... 100 - 119 are grouped by a factor 5 ... 120 - 127 are grouped by a factor 4 ... 128 - 139 are grouped by a factor 6 ... 140 - 149 are grouped by a factor 5 ... 150 - 170 are grouped by a factor 7 ... 171 - 200 are grouped by a factor 6 ... 201 - 207 are grouped by a factor 7 ... 208 - 212 are grouped by a factor 5 ... 213 - 218 are grouped by a factor 6 ... 219 - 226 are grouped by a factor 8 ... 227 - 231 are grouped by a factor 5 ... 232 - 245 are grouped by a factor 7 ... 246 - 261 are grouped by a factor 8 ... 262 - 268 are grouped by a factor 7 ... 269 - 284 are grouped by a factor 8 ... 285 - 294 are grouped by a factor 10 ... 295 - 302 are grouped by a factor 8 ... 303 - 320 are grouped by a factor 9 ... 321 - 334 are grouped by a factor 14 ... 335 - 345 are grouped by a factor 11 ... 346 - 360 are grouped by a factor 15 ... 361 - 379 are grouped by a factor 19 ... 380 - 397 are grouped by a factor 18 ... 398 - 418 are grouped by a factor 21 ... 419 - 457 are grouped by a factor 39 ... 458 - 514 are grouped by a factor 57 ... 515 - 663 are grouped by a factor 149 ... 664 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 2105 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2105 354 1751 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2105 354 1751 0 0 0
in 7049.44 seconds
Spectrum has 354 counts for 5.0217E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7049.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.90918E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 2105 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2105 1415 690 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2105 1415 690 0 0 0
in 7049.44 seconds
Spectrum has 1415 counts for 0.2007 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7049.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.10462 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 2105 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2105 315 1790 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2105 315 1790 0 0 0
in 7049.44 seconds
Spectrum has 315 counts for 4.4684E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7049.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.28223E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 2105 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2105 21 2084 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2105 21 2084 0 0 0
in 7049.44 seconds
Spectrum has 21 counts for 2.9790E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7049.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.25586E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.168171021377672 rmf1.tmp 0.672209026128266 rmf2.tmp 0.149643705463183 rmf3.tmp 0.00997624703087886-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.682E-01 * rmf0.tmp
6.722E-01 * rmf1.tmp
1.496E-01 * rmf2.tmp
9.976E-03 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.17
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.67
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.15
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.01
ASCA SIS0 NONE NONE PI
-> Generating ad54000060s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 84 by 79 bins
expanded to 84 by 79 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 229.07 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.06500E+03
Weighted mean angle from optical axis = 8.076 arcmin
-> Standard Output From STOOL group_event_files:1 ad54000060s100102h.evt 3281 1 ad54000060s100302m.evt 3281-> Fetching SIS1_OFFCHIP.1
ad54000060s100102h.evt ad54000060s100302m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
2 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.57E+01 47 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 1857 1377 0 0 0
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 0 47 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3281 1857 1424 0 0 0
in 7628.95 seconds
Spectrum has 1857 counts for 0.2434 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7629.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.20772 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 1857 1377 0 0 0
Writing events file
1857 events written to the output file
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 0 47 0 0 0
Writing events file
1857 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3281 1857 1424 0 0 0
in 7628.95 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad54000060s100302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad54000060s110102_1.pi group=yes
Wrote spectrum to ad54000060s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad54000060s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7629.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20772 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 31 are grouped by a factor 16 ... 32 - 43 are grouped by a factor 6 ... 44 - 51 are grouped by a factor 4 ... 52 - 57 are grouped by a factor 3 ... 58 - 59 are grouped by a factor 2 ... 60 - 62 are grouped by a factor 3 ... 63 - 64 are grouped by a factor 2 ... 65 - 68 are grouped by a factor 4 ... 69 - 74 are grouped by a factor 3 ... 75 - 78 are grouped by a factor 4 ... 79 - 83 are grouped by a factor 5 ... 84 - 107 are grouped by a factor 4 ... 108 - 113 are grouped by a factor 3 ... 114 - 118 are grouped by a factor 5 ... 119 - 130 are grouped by a factor 4 ... 131 - 145 are grouped by a factor 5 ... 146 - 151 are grouped by a factor 6 ... 152 - 158 are grouped by a factor 7 ... 159 - 163 are grouped by a factor 5 ... 164 - 169 are grouped by a factor 6 ... 170 - 185 are grouped by a factor 8 ... 186 - 195 are grouped by a factor 10 ... 196 - 210 are grouped by a factor 15 ... 211 - 229 are grouped by a factor 19 ... 230 - 250 are grouped by a factor 21 ... 251 - 289 are grouped by a factor 39 ... 290 - 461 are grouped by a factor 172 ... 462 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 1857 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1857 263 1594 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1857 263 1594 0 0 0
in 7628.95 seconds
Spectrum has 263 counts for 3.4474E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7629.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.55469E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 1857 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1857 19 1838 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1857 19 1838 0 0 0
in 7628.95 seconds
Spectrum has 19 counts for 2.4905E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7629.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.71094E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 1857 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1857 440 1417 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1857 440 1417 0 0 0
in 7628.95 seconds
Spectrum has 440 counts for 5.7675E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7629.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.38477E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 1857 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1857 1135 722 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1857 1135 722 0 0 0
in 7628.95 seconds
Spectrum has 1135 counts for 0.1488 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7629.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.10462 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.141626278944534 rmf1.tmp 0.0102315562735595 rmf2.tmp 0.236941303177167 rmf3.tmp 0.611200861604739-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.416E-01 * rmf0.tmp
1.023E-02 * rmf1.tmp
2.369E-01 * rmf2.tmp
6.112E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.14
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.01
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.24
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.61
ASCA SIS1 NONE NONE PI
-> Generating ad54000060s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 85 by 81 bins
expanded to 85 by 81 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 239.36 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.81400E+03
Weighted mean angle from optical axis = 10.136 arcmin
-> Standard Output From STOOL group_event_files:1 ad54000060s100112h.evt 4120-> SIS1_OFFCHIP.1 already present in current directory
ad54000060s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 4120 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100112h.evt
Total Good Bad: Region Time Phase Cut
4120 2395 1725 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4120 2395 1725 0 0 0
in 7623.30 seconds
Spectrum has 2395 counts for 0.3142 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7623.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.20772 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060s110212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100112h.evt
Total Good Bad: Region Time Phase Cut
4120 2395 1725 0 0 0
Writing events file
2395 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4120 2395 1725 0 0 0
in 7623.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad54000060s110212_1.pi group=yes
Wrote spectrum to ad54000060s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad54000060s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7623.3 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.20772 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 56 are grouped by a factor 24 ... 57 - 65 are grouped by a factor 9 ... 66 - 73 are grouped by a factor 8 ... 74 - 82 are grouped by a factor 9 ... 83 - 94 are grouped by a factor 6 ... 95 - 102 are grouped by a factor 4 ... 103 - 108 are grouped by a factor 6 ... 109 - 116 are grouped by a factor 4 ... 117 - 121 are grouped by a factor 5 ... 122 - 125 are grouped by a factor 4 ... 126 - 140 are grouped by a factor 5 ... 141 - 147 are grouped by a factor 7 ... 148 - 153 are grouped by a factor 6 ... 154 - 167 are grouped by a factor 7 ... 168 - 179 are grouped by a factor 6 ... 180 - 193 are grouped by a factor 7 ... 194 - 211 are grouped by a factor 6 ... 212 - 216 are grouped by a factor 5 ... 217 - 220 are grouped by a factor 4 ... 221 - 227 are grouped by a factor 7 ... 228 - 233 are grouped by a factor 6 ... 234 - 240 are grouped by a factor 7 ... 241 - 244 are grouped by a factor 4 ... 245 - 251 are grouped by a factor 7 ... 252 - 259 are grouped by a factor 8 ... 260 - 266 are grouped by a factor 7 ... 267 - 274 are grouped by a factor 8 ... 275 - 280 are grouped by a factor 6 ... 281 - 289 are grouped by a factor 9 ... 290 - 296 are grouped by a factor 7 ... 297 - 304 are grouped by a factor 8 ... 305 - 313 are grouped by a factor 9 ... 314 - 321 are grouped by a factor 8 ... 322 - 341 are grouped by a factor 10 ... 342 - 352 are grouped by a factor 11 ... 353 - 364 are grouped by a factor 12 ... 365 - 378 are grouped by a factor 14 ... 379 - 397 are grouped by a factor 19 ... 398 - 418 are grouped by a factor 21 ... 419 - 441 are grouped by a factor 23 ... 442 - 467 are grouped by a factor 26 ... 468 - 508 are grouped by a factor 41 ... 509 - 571 are grouped by a factor 63 ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 2395 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2395 349 2046 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2395 349 2046 0 0 0
in 7623.30 seconds
Spectrum has 349 counts for 4.5781E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7623.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.55469E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 2395 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2395 25 2370 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2395 25 2370 0 0 0
in 7623.30 seconds
Spectrum has 25 counts for 3.2794E-03 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7623.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.71094E-03 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 2395 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2395 541 1854 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2395 541 1854 0 0 0
in 7623.30 seconds
Spectrum has 541 counts for 7.0967E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7623.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.38477E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 2395 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2395 1480 915 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2395 1480 915 0 0 0
in 7623.30 seconds
Spectrum has 1480 counts for 0.1941 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7623.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.10462 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.145720250521921 rmf1.tmp 0.0104384133611691 rmf2.tmp 0.225887265135699 rmf3.tmp 0.617954070981211-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.457E-01 * rmf0.tmp
1.044E-02 * rmf1.tmp
2.259E-01 * rmf2.tmp
6.180E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.15
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.01
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.23
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.62
ASCA SIS1 NONE NONE PI
-> Generating ad54000060s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 85 by 81 bins
expanded to 85 by 81 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 239.36 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.33400E+03
Weighted mean angle from optical axis = 10.154 arcmin
-> Standard Output From STOOL group_event_files:1 ad54000060g200170h.evt 12214-> GIS2_REGION256.4 already present in current directory
ad54000060g200170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 12214 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
in 9314.28 seconds
Spectrum has 8559 counts for 0.9189 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 9314.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.19075 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad54000060g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad54000060g210170_1.pi group=yes
Wrote spectrum to ad54000060g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad54000060g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad54000060g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 9314.3 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.19075 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 24 are grouped by a factor 25 ... 25 - 35 are grouped by a factor 11 ... 36 - 44 are grouped by a factor 9 ... 45 - 58 are grouped by a factor 14 ... 59 - 68 are grouped by a factor 10 ... 69 - 80 are grouped by a factor 6 ... 81 - 90 are grouped by a factor 5 ... 91 - 106 are grouped by a factor 4 ... 107 - 112 are grouped by a factor 3 ... 113 - 114 are grouped by a factor 2 ... 115 - 120 are grouped by a factor 3 ... 121 - 122 are grouped by a factor 2 ... 123 - 125 are grouped by a factor 3 ... 126 - 133 are grouped by a factor 2 ... 134 - 136 are grouped by a factor 3 ... 137 - 160 are grouped by a factor 2 ... 161 - 162 are single channels ... 163 - 164 are grouped by a factor 2 ... 165 - 165 are single channels ... 166 - 171 are grouped by a factor 2 ... 172 - 172 are single channels ... 173 - 192 are grouped by a factor 2 ... 193 - 195 are grouped by a factor 3 ... 196 - 197 are grouped by a factor 2 ... 198 - 200 are grouped by a factor 3 ... 201 - 242 are grouped by a factor 2 ... 243 - 245 are grouped by a factor 3 ... 246 - 249 are grouped by a factor 2 ... 250 - 252 are grouped by a factor 3 ... 253 - 270 are grouped by a factor 2 ... 271 - 273 are grouped by a factor 3 ... 274 - 277 are grouped by a factor 2 ... 278 - 283 are grouped by a factor 3 ... 284 - 285 are grouped by a factor 2 ... 286 - 291 are grouped by a factor 3 ... 292 - 299 are grouped by a factor 2 ... 300 - 338 are grouped by a factor 3 ... 339 - 340 are grouped by a factor 2 ... 341 - 355 are grouped by a factor 3 ... 356 - 359 are grouped by a factor 4 ... 360 - 362 are grouped by a factor 3 ... 363 - 378 are grouped by a factor 4 ... 379 - 381 are grouped by a factor 3 ... 382 - 385 are grouped by a factor 4 ... 386 - 388 are grouped by a factor 3 ... 389 - 400 are grouped by a factor 4 ... 401 - 405 are grouped by a factor 5 ... 406 - 409 are grouped by a factor 4 ... 410 - 412 are grouped by a factor 3 ... 413 - 442 are grouped by a factor 5 ... 443 - 446 are grouped by a factor 4 ... 447 - 451 are grouped by a factor 5 ... 452 - 475 are grouped by a factor 6 ... 476 - 483 are grouped by a factor 8 ... 484 - 492 are grouped by a factor 9 ... 493 - 498 are grouped by a factor 6 ... 499 - 506 are grouped by a factor 8 ... 507 - 516 are grouped by a factor 10 ... 517 - 523 are grouped by a factor 7 ... 524 - 543 are grouped by a factor 10 ... 544 - 556 are grouped by a factor 13 ... 557 - 565 are grouped by a factor 9 ... 566 - 577 are grouped by a factor 12 ... 578 - 588 are grouped by a factor 11 ... 589 - 605 are grouped by a factor 17 ... 606 - 629 are grouped by a factor 24 ... 630 - 699 are grouped by a factor 35 ... 700 - 745 are grouped by a factor 46 ... 746 - 846 are grouped by a factor 101 ... 847 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 116 by 140 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel -28 -16
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 753.93 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.55900E+03
Weighted mean angle from optical axis = 14.521 arcmin
-> Standard Output From STOOL group_event_files:1 ad54000060g300170h.evt 13979-> GIS3_REGION256.4 already present in current directory
ad54000060g300170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 13979 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
in 9320.28 seconds
Spectrum has 7061 counts for 0.7576 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 9320.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.11917 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad54000060g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad54000060g310170_1.pi group=yes
Wrote spectrum to ad54000060g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad54000060g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad54000060g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 9320.3 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.11917 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 are grouped by a factor 26 ... 26 - 44 are grouped by a factor 19 ... 45 - 57 are grouped by a factor 13 ... 58 - 69 are grouped by a factor 12 ... 70 - 79 are grouped by a factor 10 ... 80 - 93 are grouped by a factor 7 ... 94 - 98 are grouped by a factor 5 ... 99 - 114 are grouped by a factor 4 ... 115 - 132 are grouped by a factor 3 ... 133 - 134 are grouped by a factor 2 ... 135 - 137 are grouped by a factor 3 ... 138 - 141 are grouped by a factor 2 ... 142 - 144 are grouped by a factor 3 ... 145 - 192 are grouped by a factor 2 ... 193 - 195 are grouped by a factor 3 ... 196 - 199 are grouped by a factor 2 ... 200 - 202 are grouped by a factor 3 ... 203 - 214 are grouped by a factor 2 ... 215 - 217 are grouped by a factor 3 ... 218 - 221 are grouped by a factor 2 ... 222 - 224 are grouped by a factor 3 ... 225 - 226 are grouped by a factor 2 ... 227 - 250 are grouped by a factor 3 ... 251 - 252 are grouped by a factor 2 ... 253 - 258 are grouped by a factor 3 ... 259 - 260 are grouped by a factor 2 ... 261 - 263 are grouped by a factor 3 ... 264 - 267 are grouped by a factor 2 ... 268 - 270 are grouped by a factor 3 ... 271 - 274 are grouped by a factor 2 ... 275 - 295 are grouped by a factor 3 ... 296 - 299 are grouped by a factor 4 ... 300 - 320 are grouped by a factor 3 ... 321 - 322 are grouped by a factor 2 ... 323 - 330 are grouped by a factor 4 ... 331 - 339 are grouped by a factor 3 ... 340 - 341 are grouped by a factor 2 ... 342 - 347 are grouped by a factor 3 ... 348 - 355 are grouped by a factor 4 ... 356 - 361 are grouped by a factor 3 ... 362 - 369 are grouped by a factor 4 ... 370 - 374 are grouped by a factor 5 ... 375 - 378 are grouped by a factor 4 ... 379 - 383 are grouped by a factor 5 ... 384 - 387 are grouped by a factor 4 ... 388 - 392 are grouped by a factor 5 ... 393 - 396 are grouped by a factor 4 ... 397 - 399 are grouped by a factor 3 ... 400 - 415 are grouped by a factor 4 ... 416 - 420 are grouped by a factor 5 ... 421 - 424 are grouped by a factor 4 ... 425 - 429 are grouped by a factor 5 ... 430 - 435 are grouped by a factor 6 ... 436 - 440 are grouped by a factor 5 ... 441 - 446 are grouped by a factor 6 ... 447 - 451 are grouped by a factor 5 ... 452 - 465 are grouped by a factor 7 ... 466 - 471 are grouped by a factor 6 ... 472 - 495 are grouped by a factor 8 ... 496 - 522 are grouped by a factor 9 ... 523 - 533 are grouped by a factor 11 ... 534 - 546 are grouped by a factor 13 ... 547 - 562 are grouped by a factor 16 ... 563 - 577 are grouped by a factor 15 ... 578 - 590 are grouped by a factor 13 ... 591 - 617 are grouped by a factor 27 ... 618 - 651 are grouped by a factor 34 ... 652 - 689 are grouped by a factor 38 ... 690 - 741 are grouped by a factor 52 ... 742 - 860 are grouped by a factor 119 ... 861 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad54000060g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 99 by 109 bins
expanded to 128 by 256 bins
First WMAP bin is at detector pixel 28 -32
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 471.02 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.06100E+03
Weighted mean angle from optical axis = 13.445 arcmin
-> Plotting ad54000060g210170_1_pi.ps from ad54000060g210170_1.pi
XSPEC 9.01 11:06:13 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060g210170_1.pi
Net count rate (cts/s) for file 1 0.9189 +/- 1.0018E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad54000060g310170_1_pi.ps from ad54000060g310170_1.pi
XSPEC 9.01 11:06:28 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060g310170_1.pi
Net count rate (cts/s) for file 1 0.7576 +/- 9.1073E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad54000060s010102_1_pi.ps from ad54000060s010102_1.pi
XSPEC 9.01 11:06:41 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060s010102_1.pi
Net count rate (cts/s) for file 1 0.2626 +/- 6.1278E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad54000060s010212_1_pi.ps from ad54000060s010212_1.pi
XSPEC 9.01 11:06:55 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060s010212_1.pi
Net count rate (cts/s) for file 1 0.2986 +/- 7.0458E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad54000060s110102_1_pi.ps from ad54000060s110102_1.pi
XSPEC 9.01 11:07:11 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060s110102_1.pi
Net count rate (cts/s) for file 1 0.2434 +/- 5.7451E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad54000060s110212_1_pi.ps from ad54000060s110212_1.pi
XSPEC 9.01 11:07:25 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad54000060s110212_1.pi
Net count rate (cts/s) for file 1 0.3142 +/- 6.4637E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
2 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.39E+03 242 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
2 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.39E+03 242 1111
3 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.57E+01 34 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 1868 1059 0 0 0
Writing events file
1868 events written to the output file
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.evt
Total Good Bad: Region Time Phase Cut
242 130 112 0 0 0
Writing events file
1998 events written to the output file
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 34 0 0 0 0
Writing events file
2032 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3203 2032 1171 0 0 0
in 7449.32 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad54000060s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad54000060s000402m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad54000060s000002_1.lc with binsize 183.300226759972
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.74E+04 2032 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
2032 2032 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2032 2032 0 0 0 0
in 7449.32 seconds
Fits light curve has 2032 counts for 0.2728 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > set binsize 183.300226759972
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad54000060s000002_1.lc
Wrote FITS light curve to file ad54000060s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad54000060s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad54000060s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GALACTIC_RIDGE-1 Start Time (d) .... 10157 19:51:32.950
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10158 04:02:44.950
No. of Rows ....... 42 Bin Time (s) ...... 183.3
Right Ascension ... 2.6342E+02 Internal time sys.. Converted to TJD
Declination ....... -3.3000E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 161 Newbins of 183.300 (s)
Intv 1 Start10157 19:53: 4
Ser.1 Avg 0.2652 Chisq 41.78 Var 0.1577E-02 Newbs. 42
Min 0.1608 Max 0.3492 expVar 0.1585E-02 Bins 42
Results from Statistical Analysis
Newbin Integration Time (s).. 183.30
Interval Duration (s)........ 29328.
No. of Newbins .............. 42
Average (c/s) ............... 0.26520 +/- 0.62E-02
Standard Deviation (c/s)..... 0.39706E-01
Minimum (c/s)................ 0.16078
Maximum (c/s)................ 0.34915
Variance ((c/s)**2).......... 0.15765E-02 +/- 0.35E-03
Expected Variance ((c/s)**2). 0.15849E-02 +/- 0.35E-03
Third Moment ((c/s)**3)......-0.27936E-04
Average Deviation (c/s)...... 0.32764E-01
Skewness.....................-0.44629 +/- 0.38
Kurtosis.....................-0.14649 +/- 0.76
RMS fractional variation....< 0.13426 (3 sigma)
Chi-Square................... 41.777 dof 41
Chi-Square Prob of constancy. 0.43681 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.17286 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 161 Newbins of 183.300 (s)
Intv 1 Start10157 19:53: 4
Ser.1 Avg 0.2652 Chisq 41.78 Var 0.1577E-02 Newbs. 42
Min 0.1608 Max 0.3492 expVar 0.1585E-02 Bins 42
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=1.6000000000E+01 for ad54000060s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
2 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.57E+01 47 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 1900 1334 0 0 0
Writing events file
1900 events written to the output file
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 0 47 0 0 0
Writing events file
1900 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3281 1900 1381 0 0 0
in 7628.95 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad54000060s100302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad54000060s100002_1.lc with binsize 200.761870043058
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 1900 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
1900 1900 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1900 1900 0 0 0 0
in 7628.95 seconds
Fits light curve has 1900 counts for 0.2491 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 200.761870043058
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad54000060s100002_1.lc
Wrote FITS light curve to file ad54000060s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad54000060s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad54000060s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GALACTIC_RIDGE-1 Start Time (d) .... 10157 19:51:32.950
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10158 04:02:44.950
No. of Rows ....... 40 Bin Time (s) ...... 200.8
Right Ascension ... 2.6342E+02 Internal time sys.. Converted to TJD
Declination ....... -3.3000E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 147 Newbins of 200.762 (s)
Intv 1 Start10157 19:53:13
Ser.1 Avg 0.2497 Chisq 51.66 Var 0.1818E-02 Newbs. 40
Min 0.1494 Max 0.3263 expVar 0.1408E-02 Bins 40
Results from Statistical Analysis
Newbin Integration Time (s).. 200.76
Interval Duration (s)........ 29311.
No. of Newbins .............. 40
Average (c/s) ............... 0.24971 +/- 0.60E-02
Standard Deviation (c/s)..... 0.42640E-01
Minimum (c/s)................ 0.14943
Maximum (c/s)................ 0.32627
Variance ((c/s)**2).......... 0.18182E-02 +/- 0.41E-03
Expected Variance ((c/s)**2). 0.14077E-02 +/- 0.32E-03
Third Moment ((c/s)**3)......-0.50902E-05
Average Deviation (c/s)...... 0.36570E-01
Skewness.....................-0.65655E-01 +/- 0.39
Kurtosis.....................-0.83342 +/- 0.77
RMS fractional variation....< 0.10891 (3 sigma)
Chi-Square................... 51.664 dof 39
Chi-Square Prob of constancy. 0.84351E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.18879 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 147 Newbins of 200.762 (s)
Intv 1 Start10157 19:53:13
Ser.1 Avg 0.2497 Chisq 51.66 Var 0.1818E-02 Newbs. 40
Min 0.1494 Max 0.3263 expVar 0.1408E-02 Bins 40
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad54000060g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 12214 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
Writing events file
8559 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
in 9314.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > filter region ad54000060g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad54000060g200070_1.lc with binsize 54.4121826205323
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 8559 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
8559 8559 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8559 8559 0 0 0 0
in 9314.28 seconds
Fits light curve has 8559 counts for 0.9189 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > set binsize 54.4121826205323
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad54000060g200070_1.lc
Wrote FITS light curve to file ad54000060g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad54000060g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad54000060g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GALACTIC_RIDGE-1 Start Time (d) .... 10157 19:51:16.950
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10158 04:07:00.950
No. of Rows ....... 172 Bin Time (s) ...... 54.41
Right Ascension ... 2.6342E+02 Internal time sys.. Converted to TJD
Declination ....... -3.3000E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 58.1619 (s)
Intv 1 Start10157 19:51:46
Ser.1 Avg 0.9185 Chisq 143.9 Var 0.1617E-01 Newbs. 162
Min 0.6432 Max 1.274 expVar 0.1714E-01 Bins 172
Results from Statistical Analysis
Newbin Integration Time (s).. 58.162
Interval Duration (s)........ 29721.
No. of Newbins .............. 162
Average (c/s) ............... 0.91855 +/- 0.10E-01
Standard Deviation (c/s)..... 0.12717
Minimum (c/s)................ 0.64324
Maximum (c/s)................ 1.2740
Variance ((c/s)**2).......... 0.16171E-01 +/- 0.18E-02
Expected Variance ((c/s)**2). 0.17141E-01 +/- 0.19E-02
Third Moment ((c/s)**3)...... 0.99457E-04
Average Deviation (c/s)...... 0.10223
Skewness..................... 0.48364E-01 +/- 0.19
Kurtosis.....................-0.19477 +/- 0.38
RMS fractional variation....< 0.92868E-01 (3 sigma)
Chi-Square................... 143.87 dof 161
Chi-Square Prob of constancy. 0.82969 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.14013 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 58.1619 (s)
Intv 1 Start10157 19:51:46
Ser.1 Avg 0.9185 Chisq 143.9 Var 0.1617E-01 Newbs. 162
Min 0.6432 Max 1.274 expVar 0.1714E-01 Bins 172
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad54000060g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 13979 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
Writing events file
7061 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
in 9320.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > filter region ad54000060g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad54000060g300070_1.lc with binsize 65.9982820218615
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 7061 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/events.tmp
Total Good Bad: Region Time Phase Cut
7061 7061 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7061 7061 0 0 0 0
in 9320.28 seconds
Fits light curve has 7061 counts for 0.7576 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > set binsize 65.9982820218615
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad54000060g300070_1.lc
Wrote FITS light curve to file ad54000060g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad54000060g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad54000060g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GALACTIC_RIDGE-1 Start Time (d) .... 10157 19:51:16.950
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10158 04:07:00.950
No. of Rows ....... 144 Bin Time (s) ...... 66.00
Right Ascension ... 2.6342E+02 Internal time sys.. Converted to TJD
Declination ....... -3.3000E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 451 Newbins of 65.9983 (s)
Intv 1 Start10157 19:51:49
Ser.1 Avg 0.7542 Chisq 146.0 Var 0.1219E-01 Newbs. 144
Min 0.4759 Max 1.000 expVar 0.1203E-01 Bins 144
Results from Statistical Analysis
Newbin Integration Time (s).. 65.998
Interval Duration (s)........ 29699.
No. of Newbins .............. 144
Average (c/s) ............... 0.75424 +/- 0.92E-02
Standard Deviation (c/s)..... 0.11042
Minimum (c/s)................ 0.47593
Maximum (c/s)................ 1.0000
Variance ((c/s)**2).......... 0.12193E-01 +/- 0.14E-02
Expected Variance ((c/s)**2). 0.12028E-01 +/- 0.14E-02
Third Moment ((c/s)**3)......-0.12424E-03
Average Deviation (c/s)...... 0.92021E-01
Skewness.....................-0.92278E-01 +/- 0.20
Kurtosis.....................-0.71472 +/- 0.41
RMS fractional variation....< 0.89478E-01 (3 sigma)
Chi-Square................... 145.97 dof 143
Chi-Square Prob of constancy. 0.41533 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.42316 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 451 Newbins of 65.9983 (s)
Intv 1 Start10157 19:51:49
Ser.1 Avg 0.7542 Chisq 146.0 Var 0.1219E-01 Newbs. 144
Min 0.4759 Max 1.000 expVar 0.1203E-01 Bins 144
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad54000060g200170h.evt[2]-> Making L1 light curve of ft960315_1951_0420G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 26332 output records from 26365 good input G2_L1 records.-> Making L1 light curve of ft960315_1951_0420G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 8974 output records from 26365 good input G2_L1 records.-> Merging GTIs from the following files:
ad54000060g300170h.evt[2]-> Making L1 light curve of ft960315_1951_0420G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 26337 output records from 26368 good input G3_L1 records.-> Making L1 light curve of ft960315_1951_0420G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 9025 output records from 26368 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 12214 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.evt
Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
Writing events file
8559 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 8559 3655 0 0 0
in 9314.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > filter region ad54000060g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad54000060g200170h_1.ulc use_events=yes
Wrote events list to file ad54000060g200170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad54000060g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.93E+04 13979 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.evt
Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
Writing events file
7061 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13979 7061 6918 0 0 0
in 9320.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > filter region ad54000060g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad54000060g300170h_1.ulc use_events=yes
Wrote events list to file ad54000060g300170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad54000060s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.70E+04 2927 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.evt
Total Good Bad: Region Time Phase Cut
2927 1868 1059 0 0 0
Writing events file
1868 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2927 1868 1059 0 0 0
in 7049.44 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad54000060s000102h_1.ulc use_events=yes
Wrote events list to file ad54000060s000102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad54000060s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.70E+04 3448 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000112h.evt
Total Good Bad: Region Time Phase Cut
3448 2161 1287 0 0 0
Writing events file
2161 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3448 2161 1287 0 0 0
in 7049.44 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad54000060s000112h_1.ulc use_events=yes
Wrote events list to file ad54000060s000112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad54000060s000202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.39E+03 242 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.evt
Total Good Bad: Region Time Phase Cut
242 130 112 0 0 0
Writing events file
130 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
242 130 112 0 0 0
in 394.23 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad54000060s000202h_1.ulc use_events=yes
Wrote events list to file ad54000060s000202h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad54000060s000212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 20:02:40 0.39E+03 276 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000212h.evt
Total Good Bad: Region Time Phase Cut
276 150 126 0 0 0
Writing events file
150 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
276 150 126 0 0 0
in 394.23 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad54000060s000212h_1.ulc use_events=yes
Wrote events list to file ad54000060s000212h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad54000060s000402m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.57E+01 34 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.evt
Total Good Bad: Region Time Phase Cut
34 34 0 0 0 0
Writing events file
34 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34 34 0 0 0 0
in 5.65 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s000402m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad54000060s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad54000060s000402m_1.ulc use_events=yes
Wrote events list to file ad54000060s000402m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad54000060s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.76E+04 3234 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.evt
Total Good Bad: Region Time Phase Cut
3234 1900 1334 0 0 0
Writing events file
1900 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3234 1900 1334 0 0 0
in 7623.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad54000060s100102h_1.ulc use_events=yes
Wrote events list to file ad54000060s100102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad54000060s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.76E+04 4120 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100112h.evt
Total Good Bad: Region Time Phase Cut
4120 2458 1662 0 0 0
Writing events file
2458 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4120 2458 1662 0 0 0
in 7623.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad54000060s100112h_1.ulc use_events=yes
Wrote events list to file ad54000060s100112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad54000060s100302m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.57E+01 47 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.evt
Total Good Bad: Region Time Phase Cut
47 0 47 0 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
47 0 47 0 0 0
in 5.65 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060s100302m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad54000060s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad54000060s100302m_1.ulc use_events=yes
Wrote events list to file ad54000060s100302m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/54000060.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad54000060s100302m_1.ulc since it has 0 events
*** tlmFrm Version 1.1 (1997-08-25) ***
total number of superframes: 7204
frame data: 101075616.941729 ---> 101075760.941242
S1, C2, 4 ccd mode; Output File = fr960315_1951.0420_s1c2m4a.fits
frame data: 101075780.941175 ---> 101075924.940692
S1, C3, 4 ccd mode; Output File = fr960315_1951.0420_s1c3m4a.fits
frame data: 101075944.940625 ---> 101076088.940142
S1, C0, 4 ccd mode; Output File = fr960315_1951.0420_s1c0m4a.fits
frame data: 101076108.940075 ---> 101076252.939593
S1, C1, 4 ccd mode; Output File = fr960315_1951.0420_s1c1m4a.fits
frame data: 101081312.922443 ---> 101081456.921955
S0, C0, 4 ccd mode; Output File = fr960315_1951.0420_s0c0m4a.fits
frame data: 101081476.921887 ---> 101081620.9214
S0, C1, 4 ccd mode; Output File = fr960315_1951.0420_s0c1m4a.fits
frame data: 101081640.921332 ---> 101081784.920848
S0, C2, 4 ccd mode; Output File = fr960315_1951.0420_s0c2m4a.fits
frame data: 101081804.920781 ---> 101081948.920298
S0, C3, 4 ccd mode; Output File = fr960315_1951.0420_s0c3m4a.fits
Total of 8 sets of frame data are extracted.
-> Processing fr960315_1951.0420_s0c0m4a.fitsDark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s0c0m4a.fits Output zero level image : rdd.tmp Bias level = 334-> Adding keywords to header of fr960315_1951.0420_s0c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s0c1m4a.fits Output zero level image : rdd.tmp Bias level = 298-> Adding keywords to header of fr960315_1951.0420_s0c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s0c2m4a.fits Output zero level image : rdd.tmp Bias level = 333-> Adding keywords to header of fr960315_1951.0420_s0c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s0c3m4a.fits Output zero level image : rdd.tmp Bias level = 311-> Adding keywords to header of fr960315_1951.0420_s0c3m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s1c0m4a.fits Output zero level image : rdd.tmp Bias level = 224-> Adding keywords to header of fr960315_1951.0420_s1c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s1c1m4a.fits Output zero level image : rdd.tmp Bias level = 192-> Adding keywords to header of fr960315_1951.0420_s1c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s1c2m4a.fits Output zero level image : rdd.tmp Bias level = 182-> Adding keywords to header of fr960315_1951.0420_s1c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960315_1951.0420_s1c3m4a.fits Output zero level image : rdd.tmp Bias level = 220-> Adding keywords to header of fr960315_1951.0420_s1c3m4a.fits
1 ad54000060g200170h.unf 28444 1 ad54000060g200270l.unf 28444-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 24412 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 24412 1024
2 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 4032 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.unf
Total Good Bad: Region Time Phase Cut
24412 2896 21516 0 0 0
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200270l.unf
Total Good Bad: Region Time Phase Cut
4032 1166 2866 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
28444 4062 24382 0 0 0
in 18301.94 seconds
Spectrum has 4062 counts for 0.2219 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18302. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > read events ad54000060g200270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad54000060g220170.cal group=yes
Wrote spectrum to ad54000060g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 11:25:19 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad54000060g220170.cal
Net count rate (cts/s) for file 1 0.2219 +/- 3.4918E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 5.6568E+05 using 84 PHA bins.
Reduced chi-squared = 7347.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 5.6146E+05 using 84 PHA bins.
Reduced chi-squared = 7198.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 5.6146E+05 using 84 PHA bins.
Reduced chi-squared = 7107.
!XSPEC> renorm
Chi-Squared = 1161. using 84 PHA bins.
Reduced chi-squared = 14.69
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
883.11 0 1.000 5.893 0.1253 6.2383E-02
5.4834E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
366.65 0 1.000 5.861 0.1765 9.3716E-02
4.8969E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
163.56 -1 1.000 5.914 0.2001 0.1330
3.2462E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
141.69 -2 1.000 5.964 0.2242 0.1525
1.8565E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
138.36 -3 1.000 5.942 0.2065 0.1468
2.4119E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
137.95 -4 1.000 5.951 0.2121 0.1492
2.1635E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
137.81 -5 1.000 5.947 0.2090 0.1481
2.2704E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
137.81 -2 1.000 5.948 0.2100 0.1486
2.2274E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94826 +/- 0.10209E-01
3 3 2 gaussian/b Sigma 0.210041 +/- 0.10346E-01
4 4 2 gaussian/b norm 0.148567 +/- 0.38904E-02
5 2 3 gaussian/b LineE 6.54907 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.220393 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.227426E-02 +/- 0.28300E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 137.8 using 84 PHA bins.
Reduced chi-squared = 1.744
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad54000060g220170.cal peaks at 5.94826 +/- 0.010209 keV1 ad54000060g300170h.unf 28957 1 ad54000060g300270l.unf 28957-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 25226 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 25226 1024
2 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 3731 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.unf
Total Good Bad: Region Time Phase Cut
25226 2468 22758 0 0 0
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300270l.unf
Total Good Bad: Region Time Phase Cut
3731 1053 2678 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
28957 3521 25436 0 0 0
in 18307.94 seconds
Spectrum has 3521 counts for 0.1923 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18308. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad54000060g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!xsel:ASCA > read events ad54000060g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > read events ad54000060g300270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad54000060g320170.cal group=yes
Wrote spectrum to ad54000060g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 11:26:10 18-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad54000060g320170.cal
Net count rate (cts/s) for file 1 0.1923 +/- 3.2567E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 6.3136E+05 using 84 PHA bins.
Reduced chi-squared = 8199.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 6.2673E+05 using 84 PHA bins.
Reduced chi-squared = 8035.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 6.2673E+05 using 84 PHA bins.
Reduced chi-squared = 7933.
!XSPEC> renorm
Chi-Squared = 1103. using 84 PHA bins.
Reduced chi-squared = 13.97
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
881.86 0 1.000 5.893 9.3540E-02 5.7380E-02
4.9583E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
334.64 0 1.000 5.865 0.1426 8.9041E-02
4.2859E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
118.63 -1 1.000 5.911 0.1562 0.1260
2.8213E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
101.55 -2 1.000 5.939 0.1696 0.1384
2.0684E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
101.09 -3 1.000 5.934 0.1647 0.1373
2.1689E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
101.08 -4 1.000 5.935 0.1649 0.1375
2.1517E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93498 +/- 0.83253E-02
3 3 2 gaussian/b Sigma 0.164891 +/- 0.96766E-02
4 4 2 gaussian/b norm 0.137522 +/- 0.33422E-02
5 2 3 gaussian/b LineE 6.53444 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.173018 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.151706E-02 +/- 0.21505E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 101.1 using 84 PHA bins.
Reduced chi-squared = 1.279
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad54000060g320170.cal peaks at 5.93498 +/- 0.0083253 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.95E+04 118974 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000102h.unf
Total Good Bad: Region Time Phase Cut
118974 277 0 118697 0 0
Writing events file
277 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
118974 277 0 118697 0 0
in 13.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 277
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 277
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 70 149 27 31
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 70 149 27 31
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 277
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.95E+04 122512 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000112h.unf
Total Good Bad: Region Time Phase Cut
122512 303 0 122209 0 0
Writing events file
303 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
122512 303 0 122209 0 0
in 13.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad54000060s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 303
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 303
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 73 170 27 33
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 73 170 27 33
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 303
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 20:02:40 0.25E+04 22234 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/ad54000060s000202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad54000060s000202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 20:02:40 0.25E+04 26571 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/54000060.005/ad54000060s000212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad54000060s000212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:42:32 0.28E+04 20504 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000302l.unf
Total Good Bad: Region Time Phase Cut
20504 19404 0 1100 0 0
Writing events file
19404 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
20504 19404 0 1100 0 0
in 2580.20 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 19404
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 40 4770
Flickering pixels iter, pixels & cnts : 1 21 213
cleaning chip # 1
Hot pixels & counts : 38 4828
Flickering pixels iter, pixels & cnts : 1 16 166
cleaning chip # 2
Hot pixels & counts : 29 3531
Flickering pixels iter, pixels & cnts : 1 16 188
cleaning chip # 3
Hot pixels & counts : 44 4729
Flickering pixels iter, pixels & cnts : 1 19 172
Number of pixels rejected : 223
Number of (internal) image counts : 19404
Number of image cts rejected (N, %) : 18597 95.8410645
By chip : 0 1 2 3
Pixels rejected : 61 54 45 63
Image counts : 5184 5175 3917 5128
Image cts rejected: 4983 4994 3719 4901
Image cts rej (%) : 96.12 96.50 94.95 95.57
filtering data...
Total counts : 5184 5175 3917 5128
Total cts rejected: 4983 4994 3719 4901
Total cts rej (%) : 96.12 96.50 94.95 95.57
Number of clean counts accepted : 807
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 223
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s000402m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:30:32 0.14E+04 15538 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000402m.unf
Total Good Bad: Region Time Phase Cut
15538 1860 0 13678 0 0
Writing events file
1860 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15538 1860 0 13678 0 0
in 187.50 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s000402m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s000402m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1860
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 65 707
Flickering pixels iter, pixels & cnts : 1 14 81
cleaning chip # 1
Hot pixels & counts : 36 380
Flickering pixels iter, pixels & cnts : 1 4 21
cleaning chip # 2
Hot pixels & counts : 22 230
Flickering pixels iter, pixels & cnts : 1 9 33
cleaning chip # 3
Hot pixels & counts : 28 296
Flickering pixels iter, pixels & cnts : 1 12 52
Number of pixels rejected : 190
Number of (internal) image counts : 1860
Number of image cts rejected (N, %) : 1800 96.7741928
By chip : 0 1 2 3
Pixels rejected : 79 40 31 40
Image counts : 804 415 274 367
Image cts rejected: 788 401 263 348
Image cts rej (%) : 98.01 96.63 95.99 94.82
filtering data...
Total counts : 804 415 274 367
Total cts rejected: 788 401 263 348
Total cts rej (%) : 98.01 96.63 95.99 94.82
Number of clean counts accepted : 60
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 190
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s000502l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:20:08 0.31E+04 1441 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s000502l.unf
Total Good Bad: Region Time Phase Cut
1441 1340 0 101 0 0
Writing events file
1340 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1441 1340 0 101 0 0
in 194.80 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s000502l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s000502l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1340
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 28 301
Flickering pixels iter, pixels & cnts : 1 13 57
cleaning chip # 1
Hot pixels & counts : 28 280
Flickering pixels iter, pixels & cnts : 1 13 55
cleaning chip # 2
Hot pixels & counts : 20 159
Flickering pixels iter, pixels & cnts : 1 14 57
cleaning chip # 3
Hot pixels & counts : 30 279
Flickering pixels iter, pixels & cnts : 1 12 55
Number of pixels rejected : 158
Number of (internal) image counts : 1340
Number of image cts rejected (N, %) : 1243 92.7611923
By chip : 0 1 2 3
Pixels rejected : 41 41 34 42
Image counts : 384 361 237 358
Image cts rejected: 358 335 216 334
Image cts rej (%) : 93.23 92.80 91.14 93.30
filtering data...
Total counts : 384 361 237 358
Total cts rejected: 358 335 216 334
Total cts rej (%) : 93.23 92.80 91.14 93.30
Number of clean counts accepted : 97
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 158
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT HIGH 15/03/96 19:51:00 0.12E+05 191946 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100102h.unf
Total Good Bad: Region Time Phase Cut
191946 0 0 191946 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
191946 0 0 191946 0 0
in 13.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad54000060s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT2 HIGH 15/03/96 19:51:00 0.12E+05 203036 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100112h.unf
Total Good Bad: Region Time Phase Cut
203036 0 0 203036 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
203036 0 0 203036 0 0
in 13.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad54000060s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT LOW 15/03/96 23:20:08 0.59E+04 24281 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100202l.unf
Total Good Bad: Region Time Phase Cut
24281 22148 0 2133 0 0
Writing events file
22148 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24281 22148 0 2133 0 0
in 2784.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s100202l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s100202l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s100202l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 22148
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 41 5116
Flickering pixels iter, pixels & cnts : 1 31 219
cleaning chip # 1
Hot pixels & counts : 41 5084
Flickering pixels iter, pixels & cnts : 1 35 268
cleaning chip # 2
Hot pixels & counts : 39 5157
Flickering pixels iter, pixels & cnts : 1 27 224
cleaning chip # 3
Hot pixels & counts : 39 5073
Flickering pixels iter, pixels & cnts : 1 27 259
Number of pixels rejected : 280
Number of (internal) image counts : 22148
Number of image cts rejected (N, %) : 21400 96.6227188
By chip : 0 1 2 3
Pixels rejected : 72 76 66 66
Image counts : 5521 5551 5547 5529
Image cts rejected: 5335 5352 5381 5332
Image cts rej (%) : 96.63 96.42 97.01 96.44
filtering data...
Total counts : 5521 5551 5547 5529
Total cts rejected: 5335 5352 5381 5332
Total cts rej (%) : 96.63 96.42 97.01 96.44
Number of clean counts accepted : 748
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 280
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060s100302m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GALACTIC BRIGHT MEDIUM 15/03/96 20:26:16 0.17E+04 21265 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060s100302m.unf
Total Good Bad: Region Time Phase Cut
21265 3812 0 17453 0 0
Writing events file
3812 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21265 3812 0 17453 0 0
in 255.49 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad54000060s100302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad54000060s100302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3812
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 58 863
Flickering pixels iter, pixels & cnts : 1 10 59
cleaning chip # 1
Hot pixels & counts : 61 885
Flickering pixels iter, pixels & cnts : 1 13 77
cleaning chip # 2
Hot pixels & counts : 59 872
Flickering pixels iter, pixels & cnts : 1 14 85
cleaning chip # 3
Hot pixels & counts : 46 669
Flickering pixels iter, pixels & cnts : 1 15 82
Number of pixels rejected : 276
Number of (internal) image counts : 3812
Number of image cts rejected (N, %) : 3592 94.2287521
By chip : 0 1 2 3
Pixels rejected : 68 74 73 61
Image counts : 950 990 982 890
Image cts rejected: 922 962 957 751
Image cts rej (%) : 97.05 97.17 97.45 84.38
filtering data...
Total counts : 950 990 982 890
Total cts rejected: 922 962 957 751
Total cts rej (%) : 97.05 97.17 97.45 84.38
Number of clean counts accepted : 220
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 276
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad54000060g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 24412 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.unf
Total Good Bad: Region Time Phase Cut
24412 586 0 23826 0 0
Writing events file
586 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24412 586 0 23826 0 0
in 994.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad54000060g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 24412 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200170h.unf
Total Good Bad: Region Time Phase Cut
24412 199 0 24213 0 0
Writing events file
199 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24412 199 0 24213 0 0
in 257.75 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad54000060g200270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 4032 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200270l.unf
Total Good Bad: Region Time Phase Cut
4032 1273 0 2759 0 0
Writing events file
1273 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4032 1273 0 2759 0 0
in 2127.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad54000060g200270l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 4032 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g200270l.unf
Total Good Bad: Region Time Phase Cut
4032 2723 0 1309 0 0
Writing events file
2723 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4032 2723 0 1309 0 0
in 3844.17 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad54000060g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 25226 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.unf
Total Good Bad: Region Time Phase Cut
25226 503 0 24723 0 0
Writing events file
503 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25226 503 0 24723 0 0
in 994.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad54000060g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH HIGH 15/03/96 19:51:12 0.12E+05 25226 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300170h.unf
Total Good Bad: Region Time Phase Cut
25226 185 0 25041 0 0
Writing events file
185 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25226 185 0 25041 0 0
in 257.75 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad54000060g300270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 3731 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300270l.unf
Total Good Bad: Region Time Phase Cut
3731 1079 0 2652 0 0
Writing events file
1079 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3731 1079 0 2652 0 0
in 2127.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad54000060g300270l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GALACTIC PH LOW 15/03/96 20:10:32 0.60E+04 3731 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/54000060.005/ad54000060g300270l.unf
Total Good Bad: Region Time Phase Cut
3731 2614 0 1117 0 0
Writing events file
2614 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3731 2614 0 1117 0 0
in 3844.17 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/54000060.005/
Setting mkf directory to /data/data24/seq_proc/54000060.005/
!earthevents:ASCA > read events ad54000060g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/54000060.005/
HK Directory is: /data/data24/seq_proc/54000060.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad54000060s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad54000060s000202h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad54000060s000102h.unf
ad54000060s000302l.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad54000060s000502l.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad54000060s000302l.unf
ad54000060s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad54000060s000212h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad54000060s000112h.unf
ad54000060s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad54000060s000201h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad54000060s000101h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files