The following information is also available:
Time column is TIME ORDERED-> Fetching fa970420_1510.2120.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 135703560.366600 135724819.300300
Data file start and stop ascatime : 135703560.366600 135724819.300300
Aspecting run start and stop ascatime : 135703560.366672 135724819.300206
Time interval averaged over (seconds) : 21258.933534
Total pointing and manuver time (sec) : 12697.482422 8561.486328
Mean boresight Euler angles : 279.507242 96.374925 21.219965
RA DEC SUN ANGLE
Mean solar position (deg) : 27.65 11.38
Mean aberration (arcsec) : 7.37 -5.06
Mean sat X-axis (deg) : 25.466032 -67.885530 79.28
Mean sat Y-axis (deg) : 7.038647 21.082470 22.01
Mean sat Z-axis (deg) : 279.507242 -6.374925 108.98
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 279.694855 -6.160404 291.240540 0.201041
Minimum 279.692261 -6.164608 291.230743 0.000000
Maximum 279.709900 -6.158179 291.340088 9.944625
Sigma (RMS) 0.001394 0.000135 0.004813 0.236191
Number of ASPECT records processed = 18005
Aspecting to RA/DEC : 279.69485474 -6.16040373
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 279.695 DEC: -6.160
START TIME: SC 135703560.3667 = UT 20/04/97 15:26:00
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
48.000053 9.945 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
95.999992 7.741 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
167.999603 5.062 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
203.999603 4.042 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
255.999481 2.991 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
327.999176 1.984 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
463.998718 0.978 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1967.994141 0.296 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
5503.982910 0.905 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
7697.976074 0.054 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
11241.964844 0.353 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
13441.958008 0.120 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
17023.947266 0.128 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
19199.939453 0.154 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
21258.433594 0.563 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
21258.933594 0.643 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 18005
Attitude Steps: 16
Maneuver ACM time: 8561.50 sec
Pointed ACM time: 12697.5 sec
-> Calculating aspect point100 100 count=1 sum1=279.378 sum2=96.381 sum3=21.293 101 99 count=1 sum1=279.39 sum2=96.38 sum3=21.285 104 99 count=2 sum1=558.848 sum2=192.756 sum3=42.53 105 99 count=6 sum1=1676.59 sum2=578.264 sum3=127.56 106 99 count=4 sum1=1117.77 sum2=385.508 sum3=85.011 107 99 count=7 sum1=1956.17 sum2=674.633 sum3=148.72 108 99 count=10 sum1=2794.63 sum2=963.759 sum3=212.406 109 99 count=8 sum1=2235.79 sum2=771 sum3=169.877 110 99 count=16 sum1=4471.74 sum2=1541.99 sum3=339.673 111 99 count=26 sum1=7266.82 sum2=2505.72 sum3=551.842 112 99 count=15102 sum1=4.22108e+06 sum2=1.45544e+06 sum3=320470 113 99 count=2720 sum1=760271 sum2=262145 sum3=57713 114 99 count=101 sum1=28231.6 sum2=9734.18 sum3=2142.49 0 out of 18004 points outside bin structure-> Euler angles: 279.506, 96.3747, 21.22
Interpolating 4 records in time interval 1.35704e+08 - 1.35704e+08 Interpolating 4 records in time interval 1.35704e+08 - 1.35704e+08 Interpolating 3 records in time interval 1.35704e+08 - 1.35704e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft970420_1510.2120",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft970420_1510.2120 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 1 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 236492 Bright = 30068 Fast = 0 Frame = 21696 Dark frame = 0 Histogram = 0 Integration = 0 PH = 288256 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 4549 no. of SIS events found = 677132-> Standard Error Output From FTOOL frfread
coordinate error 489 82 coordinate error 505 31 coordinate error 0 192 coordinate error 96 0 coordinate error 192 0 coordinate error 0 48 coordinate error 24 0 coordinate error 0 0 coordinate error 434 101 coordinate error 0 0 coordinate error 0 1 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 24 coordinate error 0 0-> Removing the following files with NEVENTS=0
ft970420_1510_2120G200570L.fits ft970420_1510_2120G200670M.fits ft970420_1510_2120G201070H.fits ft970420_1510_2120G201370L.fits ft970420_1510_2120G201470H.fits ft970420_1510_2120G201570H.fits ft970420_1510_2120G201670H.fits ft970420_1510_2120G201770H.fits ft970420_1510_2120G201870L.fits ft970420_1510_2120G201970H.fits ft970420_1510_2120G202170H.fits ft970420_1510_2120G202670L.fits ft970420_1510_2120G202799.fits ft970420_1510_2120G202870M.fits ft970420_1510_2120G203299.fits ft970420_1510_2120G203499.fits ft970420_1510_2120G203670H.fits ft970420_1510_2120G203770H.fits ft970420_1510_2120G203870H.fits ft970420_1510_2120G203970H.fits ft970420_1510_2120G204070H.fits ft970420_1510_2120G300570L.fits ft970420_1510_2120G300670M.fits ft970420_1510_2120G301370L.fits ft970420_1510_2120G301470H.fits ft970420_1510_2120G301570H.fits ft970420_1510_2120G301670H.fits ft970420_1510_2120G301770H.fits ft970420_1510_2120G301870L.fits ft970420_1510_2120G301970H.fits ft970420_1510_2120G302670L.fits ft970420_1510_2120G302799.fits ft970420_1510_2120G302870M.fits ft970420_1510_2120G303299.fits ft970420_1510_2120G303499.fits ft970420_1510_2120G303770H.fits ft970420_1510_2120G303870H.fits ft970420_1510_2120G303970H.fits ft970420_1510_2120G304170H.fits ft970420_1510_2120S000402M.fits ft970420_1510_2120S000502M.fits ft970420_1510_2120S000602M.fits ft970420_1510_2120S000902L.fits ft970420_1510_2120S001002M.fits ft970420_1510_2120S001202H.fits ft970420_1510_2120S001502L.fits ft970420_1510_2120S001602L.fits ft970420_1510_2120S001702H.fits ft970420_1510_2120S001804H.fits ft970420_1510_2120S001902H.fits ft970420_1510_2120S002002H.fits ft970420_1510_2120S002102L.fits ft970420_1510_2120S002201L.fits ft970420_1510_2120S002702L.fits ft970420_1510_2120S002802L.fits ft970420_1510_2120S002999.fits ft970420_1510_2120S003299.fits ft970420_1510_2120S003499.fits ft970420_1510_2120S100302M.fits ft970420_1510_2120S100402M.fits ft970420_1510_2120S100602L.fits ft970420_1510_2120S100702M.fits ft970420_1510_2120S101002L.fits ft970420_1510_2120S101102L.fits ft970420_1510_2120S101202H.fits ft970420_1510_2120S101302L.fits ft970420_1510_2120S101401L.fits ft970420_1510_2120S101802L.fits ft970420_1510_2120S101999.fits ft970420_1510_2120S102299.fits ft970420_1510_2120S102499.fits-> Checking for empty GTI extensions
ft970420_1510_2120S000102L.fits[3] ft970420_1510_2120S000202M.fits[3] ft970420_1510_2120S000302M.fits[3] ft970420_1510_2120S000702L.fits[3] ft970420_1510_2120S000802L.fits[3] ft970420_1510_2120S001102M.fits[3] ft970420_1510_2120S001301H.fits[3] ft970420_1510_2120S001401H.fits[3] ft970420_1510_2120S002301H.fits[3] ft970420_1510_2120S002401H.fits[3] ft970420_1510_2120S002502H.fits[3] ft970420_1510_2120S002602L.fits[3] ft970420_1510_2120S003002M.fits[3] ft970420_1510_2120S003101H.fits[3] ft970420_1510_2120S003301H.fits[3] ft970420_1510_2120S003501H.fits[3] ft970420_1510_2120S003601H.fits[3]-> Merging GTIs from the following files:
ft970420_1510_2120S100102L.fits[3] ft970420_1510_2120S100202M.fits[3] ft970420_1510_2120S100502L.fits[3] ft970420_1510_2120S100802M.fits[3] ft970420_1510_2120S100901H.fits[3] ft970420_1510_2120S101501H.fits[3] ft970420_1510_2120S101602H.fits[3] ft970420_1510_2120S101702L.fits[3] ft970420_1510_2120S102002M.fits[3] ft970420_1510_2120S102101H.fits[3] ft970420_1510_2120S102301H.fits[3] ft970420_1510_2120S102501H.fits[3]-> Merging GTIs from the following files:
ft970420_1510_2120G200170L.fits[3] ft970420_1510_2120G200270M.fits[3] ft970420_1510_2120G200370L.fits[3] ft970420_1510_2120G200470L.fits[3] ft970420_1510_2120G200770M.fits[3] ft970420_1510_2120G200870H.fits[3] ft970420_1510_2120G200970H.fits[3] ft970420_1510_2120G201170H.fits[3] ft970420_1510_2120G201270L.fits[3] ft970420_1510_2120G202070H.fits[3] ft970420_1510_2120G202270H.fits[3] ft970420_1510_2120G202370H.fits[3] ft970420_1510_2120G202470L.fits[3] ft970420_1510_2120G202570L.fits[3] ft970420_1510_2120G202970M.fits[3] ft970420_1510_2120G203070M.fits[3] ft970420_1510_2120G203170H.fits[3] ft970420_1510_2120G203370H.fits[3] ft970420_1510_2120G203570H.fits[3] ft970420_1510_2120G204170H.fits[3] ft970420_1510_2120G204270H.fits[3]-> Merging GTIs from the following files:
ft970420_1510_2120G300170L.fits[3] ft970420_1510_2120G300270M.fits[3] ft970420_1510_2120G300370L.fits[3] ft970420_1510_2120G300470L.fits[3] ft970420_1510_2120G300770M.fits[3] ft970420_1510_2120G300870H.fits[3] ft970420_1510_2120G300970H.fits[3] ft970420_1510_2120G301070H.fits[3] ft970420_1510_2120G301170H.fits[3] ft970420_1510_2120G301270L.fits[3] ft970420_1510_2120G302070H.fits[3] ft970420_1510_2120G302170H.fits[3] ft970420_1510_2120G302270H.fits[3] ft970420_1510_2120G302370H.fits[3] ft970420_1510_2120G302470L.fits[3] ft970420_1510_2120G302570L.fits[3] ft970420_1510_2120G302970M.fits[3] ft970420_1510_2120G303070M.fits[3] ft970420_1510_2120G303170H.fits[3] ft970420_1510_2120G303370H.fits[3] ft970420_1510_2120G303570H.fits[3] ft970420_1510_2120G303670H.fits[3] ft970420_1510_2120G304070H.fits[3] ft970420_1510_2120G304270H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:E1:Modal parameter missing in ft970420_1510_2120G200170L.fits GISSORTCODE:E1:ft970420_1510_2120G200170L.fits dropped from merge (72 photons) GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200370h.prelist merge count = 6 photon cnt = 8478 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g200270l.prelist merge count = 3 photon cnt = 1877 GISSORTSPLIT:LO:g200370l.prelist merge count = 1 photon cnt = 194 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 20 GISSORTSPLIT:LO:g200270m.prelist merge count = 3 photon cnt = 5492 GISSORTSPLIT:LO:Total filenames split = 20 GISSORTSPLIT:LO:Total split file cnt = 11 GISSORTSPLIT:LO:End program-> Creating ad55004000g200170h.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G201170H.fits 2 -- ft970420_1510_2120G202370H.fits 3 -- ft970420_1510_2120G203170H.fits 4 -- ft970420_1510_2120G203370H.fits 5 -- ft970420_1510_2120G203570H.fits 6 -- ft970420_1510_2120G204270H.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G201170H.fits 2 -- ft970420_1510_2120G202370H.fits 3 -- ft970420_1510_2120G203170H.fits 4 -- ft970420_1510_2120G203370H.fits 5 -- ft970420_1510_2120G203570H.fits 6 -- ft970420_1510_2120G204270H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000g200270m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G200270M.fits 2 -- ft970420_1510_2120G200770M.fits 3 -- ft970420_1510_2120G203070M.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G200270M.fits 2 -- ft970420_1510_2120G200770M.fits 3 -- ft970420_1510_2120G203070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000g200370l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G200470L.fits 2 -- ft970420_1510_2120G201270L.fits 3 -- ft970420_1510_2120G202470L.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G200470L.fits 2 -- ft970420_1510_2120G201270L.fits 3 -- ft970420_1510_2120G202470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000194 events
ft970420_1510_2120G200370L.fits-> Ignoring the following files containing 000000020 events
ft970420_1510_2120G202970M.fits-> Ignoring the following files containing 000000010 events
ft970420_1510_2120G202570L.fits-> Ignoring the following files containing 000000007 events
ft970420_1510_2120G204170H.fits-> Ignoring the following files containing 000000005 events
ft970420_1510_2120G200870H.fits-> Ignoring the following files containing 000000004 events
ft970420_1510_2120G202270H.fits-> Ignoring the following files containing 000000002 events
ft970420_1510_2120G200970H.fits-> Ignoring the following files containing 000000002 events
ft970420_1510_2120G202070H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:E1:Modal parameter missing in ft970420_1510_2120G300170L.fits GISSORTCODE:E1:ft970420_1510_2120G300170L.fits dropped from merge (66 photons) GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300570h.prelist merge count = 6 photon cnt = 8136 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g300270l.prelist merge count = 3 photon cnt = 1713 GISSORTSPLIT:LO:g300370l.prelist merge count = 1 photon cnt = 204 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g300270m.prelist merge count = 3 photon cnt = 5103 GISSORTSPLIT:LO:Total filenames split = 23 GISSORTSPLIT:LO:Total split file cnt = 14 GISSORTSPLIT:LO:End program-> Creating ad55004000g300170h.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G301170H.fits 2 -- ft970420_1510_2120G302370H.fits 3 -- ft970420_1510_2120G303170H.fits 4 -- ft970420_1510_2120G303370H.fits 5 -- ft970420_1510_2120G303570H.fits 6 -- ft970420_1510_2120G304270H.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G301170H.fits 2 -- ft970420_1510_2120G302370H.fits 3 -- ft970420_1510_2120G303170H.fits 4 -- ft970420_1510_2120G303370H.fits 5 -- ft970420_1510_2120G303570H.fits 6 -- ft970420_1510_2120G304270H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000g300270m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G300270M.fits 2 -- ft970420_1510_2120G300770M.fits 3 -- ft970420_1510_2120G303070M.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G300270M.fits 2 -- ft970420_1510_2120G300770M.fits 3 -- ft970420_1510_2120G303070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000g300370l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120G300470L.fits 2 -- ft970420_1510_2120G301270L.fits 3 -- ft970420_1510_2120G302470L.fits Merging binary extension #: 2 1 -- ft970420_1510_2120G300470L.fits 2 -- ft970420_1510_2120G301270L.fits 3 -- ft970420_1510_2120G302470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000204 events
ft970420_1510_2120G300370L.fits-> Ignoring the following files containing 000000015 events
ft970420_1510_2120G302970M.fits-> Ignoring the following files containing 000000009 events
ft970420_1510_2120G302570L.fits-> Ignoring the following files containing 000000007 events
ft970420_1510_2120G303670H.fits-> Ignoring the following files containing 000000007 events
ft970420_1510_2120G302170H.fits-> Ignoring the following files containing 000000003 events
ft970420_1510_2120G300970H.fits-> Ignoring the following files containing 000000003 events
ft970420_1510_2120G302270H.fits-> Ignoring the following files containing 000000002 events
ft970420_1510_2120G300870H.fits-> Ignoring the following files containing 000000002 events
ft970420_1510_2120G301070H.fits-> Ignoring the following files containing 000000001 events
ft970420_1510_2120G302070H.fits-> Ignoring the following files containing 000000001 events
ft970420_1510_2120G304070H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 5 photon cnt = 148539 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 3 photon cnt = 58361 SIS0SORTSPLIT:LO:s000302h.prelist merge count = 1 photon cnt = 3 SIS0SORTSPLIT:LO:s000402l.prelist merge count = 1 photon cnt = 511 SIS0SORTSPLIT:LO:s000502l.prelist merge count = 1 photon cnt = 3004 SIS0SORTSPLIT:LO:s000602l.prelist merge count = 2 photon cnt = 147 SIS0SORTSPLIT:LO:s000702m.prelist merge count = 1 photon cnt = 978 SIS0SORTSPLIT:LO:s000802m.prelist merge count = 3 photon cnt = 69122 SIS0SORTSPLIT:LO:Total filenames split = 17 SIS0SORTSPLIT:LO:Total split file cnt = 8 SIS0SORTSPLIT:LO:End program-> Creating ad55004000s000101h.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S001301H.fits 2 -- ft970420_1510_2120S002301H.fits 3 -- ft970420_1510_2120S003101H.fits 4 -- ft970420_1510_2120S003301H.fits 5 -- ft970420_1510_2120S003501H.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S001301H.fits 2 -- ft970420_1510_2120S002301H.fits 3 -- ft970420_1510_2120S003101H.fits 4 -- ft970420_1510_2120S003301H.fits 5 -- ft970420_1510_2120S003501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000s000202m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S000302M.fits 2 -- ft970420_1510_2120S001102M.fits 3 -- ft970420_1510_2120S003002M.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S000302M.fits 2 -- ft970420_1510_2120S001102M.fits 3 -- ft970420_1510_2120S003002M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000s000301h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S001401H.fits 2 -- ft970420_1510_2120S002401H.fits 3 -- ft970420_1510_2120S003601H.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S001401H.fits 2 -- ft970420_1510_2120S002401H.fits 3 -- ft970420_1510_2120S003601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft970420_1510_2120S000802L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S000802L.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S000802L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000978 events
ft970420_1510_2120S000202M.fits-> Ignoring the following files containing 000000511 events
ft970420_1510_2120S000102L.fits-> Ignoring the following files containing 000000147 events
ft970420_1510_2120S000702L.fits ft970420_1510_2120S002602L.fits-> Ignoring the following files containing 000000003 events
ft970420_1510_2120S002502H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 5 photon cnt = 283507 SIS1SORTSPLIT:LO:s100202h.prelist merge count = 1 photon cnt = 56 SIS1SORTSPLIT:LO:s100302l.prelist merge count = 1 photon cnt = 511 SIS1SORTSPLIT:LO:s100402l.prelist merge count = 2 photon cnt = 5776 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 3 photon cnt = 106601 SIS1SORTSPLIT:LO:Total filenames split = 12 SIS1SORTSPLIT:LO:Total split file cnt = 5 SIS1SORTSPLIT:LO:End program-> Creating ad55004000s100101h.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S100901H.fits 2 -- ft970420_1510_2120S101501H.fits 3 -- ft970420_1510_2120S102101H.fits 4 -- ft970420_1510_2120S102301H.fits 5 -- ft970420_1510_2120S102501H.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S100901H.fits 2 -- ft970420_1510_2120S101501H.fits 3 -- ft970420_1510_2120S102101H.fits 4 -- ft970420_1510_2120S102301H.fits 5 -- ft970420_1510_2120S102501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000s100202m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S100202M.fits 2 -- ft970420_1510_2120S100802M.fits 3 -- ft970420_1510_2120S102002M.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S100202M.fits 2 -- ft970420_1510_2120S100802M.fits 3 -- ft970420_1510_2120S102002M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55004000s100302l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970420_1510_2120S100502L.fits 2 -- ft970420_1510_2120S101702L.fits Merging binary extension #: 2 1 -- ft970420_1510_2120S100502L.fits 2 -- ft970420_1510_2120S101702L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000511 events
ft970420_1510_2120S100102L.fits-> Ignoring the following files containing 000000056 events
ft970420_1510_2120S101602H.fits-> Tar-ing together the leftover raw files
a ft970420_1510_2120G200170L.fits 40K a ft970420_1510_2120G200370L.fits 45K a ft970420_1510_2120G200870H.fits 40K a ft970420_1510_2120G200970H.fits 40K a ft970420_1510_2120G202070H.fits 40K a ft970420_1510_2120G202270H.fits 40K a ft970420_1510_2120G202570L.fits 40K a ft970420_1510_2120G202970M.fits 40K a ft970420_1510_2120G204170H.fits 40K a ft970420_1510_2120G300170L.fits 40K a ft970420_1510_2120G300370L.fits 45K a ft970420_1510_2120G300870H.fits 40K a ft970420_1510_2120G300970H.fits 40K a ft970420_1510_2120G301070H.fits 40K a ft970420_1510_2120G302070H.fits 40K a ft970420_1510_2120G302170H.fits 40K a ft970420_1510_2120G302270H.fits 40K a ft970420_1510_2120G302570L.fits 40K a ft970420_1510_2120G302970M.fits 40K a ft970420_1510_2120G303670H.fits 40K a ft970420_1510_2120G304070H.fits 40K a ft970420_1510_2120S000102L.fits 51K a ft970420_1510_2120S000202M.fits 68K a ft970420_1510_2120S000702L.fits 43K a ft970420_1510_2120S002502H.fits 40K a ft970420_1510_2120S002602L.fits 40K a ft970420_1510_2120S100102L.fits 51K a ft970420_1510_2120S101602H.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft970420_1510.2120 'ft970420_1510.2120' is successfully opened Data Start Time is 135702633.37 (970420 151033) Time Margin 2.0 sec included Sync error detected in 0 th SF Sync error detected in 1 th SF Sync error detected in 2 th SF Sync error detected in 5 th SF Sync error detected in 6 th SF Sync error detected in 10 th SF Sync error detected in 18 th SF Sync error detected in 24 th SF Sync error detected in 29 th SF Sync error detected in 37 th SF Sync error detected in 38 th SF Sync error detected in 715 th SF Sync error detected in 1292 th SF Sync error detected in 1298 th SF Sync error detected in 1503 th SF Sync error detected in 1520 th SF Sync error detected in 3575 th SF Sync error detected in 3576 th SF 'ft970420_1510.2120' EOF detected, sf=4549 Data End Time is 135724821.30 (970420 212021) Gain History is written in ft970420_1510_2120.ghf-> Checking if column CAL_START in ft970420_1510_2120.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft970420_1510_2120.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad55004000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000302h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000312h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s000402l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55004000s100302l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 97/ 4/20 15:10 mjd=50558.631944 Orbit file name is ./frf.orbit.214 Epoch of Orbital Elements: 1997/4/14 3:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa970420_1510.2120 S0-HK file: ft970420_1510_2120S0HK.fits S1-HK file: ft970420_1510_2120S1HK.fits G2-HK file: ft970420_1510_2120G2HK.fits G3-HK file: ft970420_1510_2120G3HK.fits output FITS File: ft970420_1510_2120.mkf Total 663 Data bins were processed.-> Checking if column TIME in ft970420_1510_2120.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 16623.401 The mean of the selected column is 92.352225 The standard deviation of the selected column is 95.068933 The minimum of selected column is 21.187567 The maximum of selected column is 646.27301 The number of points used in calculation is 180-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13063.583 The mean of the selected column is 72.575461 The standard deviation of the selected column is 72.470669 The minimum of selected column is 17.350054 The maximum of selected column is 529.87665 The number of points used in calculation is 180-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14213.972 The mean of the selected column is 83.122643 The standard deviation of the selected column is 94.632287 The minimum of selected column is 24.781401 The maximum of selected column is 649.06458 The number of points used in calculation is 171-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14509.927 The mean of the selected column is 80.610706 The standard deviation of the selected column is 100.03477 The minimum of selected column is 15.687614 The maximum of selected column is 775.87744 The number of points used in calculation is 180-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<377.5 )&& (S0_PIXL1>0.0 && S0_PIXL1<289.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<367 )&& (S0_PIXL3>0.0 && S0_PIXL3<380.7 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.63E+04 107456 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
71325 57990 0 13335 0 0
Writing events file
57990 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
71325 57990 0 13335 0 0
in 5157.68 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 57990
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 88 20046
Flickering pixels iter, pixels & cnts : 1 52 1050
cleaning chip # 1
Hot pixels & counts : 65 14386
Flickering pixels iter, pixels & cnts : 1 37 557
cleaning chip # 2
Hot pixels & counts : 47 8835
Flickering pixels iter, pixels & cnts : 1 36 522
cleaning chip # 3
Hot pixels & counts : 51 11088
Flickering pixels iter, pixels & cnts : 1 34 439
Number of pixels rejected : 410
Number of (internal) image counts : 57990
Number of image cts rejected (N, %) : 56923 98.1600266
By chip : 0 1 2 3
Pixels rejected : 140 102 83 85
Image counts : 21362 15229 9625 11774
Image cts rejected: 21096 14943 9357 11527
Image cts rej (%) : 98.75 98.12 97.22 97.90
filtering data...
Total counts : 21362 15229 9625 11774
Total cts rejected: 21096 14943 9357 11527
Total cts rej (%) : 98.75 98.12 97.22 97.90
Number of clean counts accepted : 1067
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 410
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55004000s000102h.evt use_events=no
Wrote cleaned events file to ad55004000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad55004000s000112h.unf into ad55004000s000112h.evtThe sum of the selected column is 16623.401 The mean of the selected column is 92.352225 The standard deviation of the selected column is 95.068933 The minimum of selected column is 21.187567 The maximum of selected column is 646.27301 The number of points used in calculation is 180-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13063.583 The mean of the selected column is 72.575461 The standard deviation of the selected column is 72.470669 The minimum of selected column is 17.350054 The maximum of selected column is 529.87665 The number of points used in calculation is 180-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14213.972 The mean of the selected column is 83.122643 The standard deviation of the selected column is 94.632287 The minimum of selected column is 24.781401 The maximum of selected column is 649.06458 The number of points used in calculation is 171-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14509.927 The mean of the selected column is 80.610706 The standard deviation of the selected column is 100.03477 The minimum of selected column is 15.687614 The maximum of selected column is 775.87744 The number of points used in calculation is 180-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<377.5 )&& (S0_PIXL1>0.0 && S0_PIXL1<289.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<367 )&& (S0_PIXL3>0.0 && S0_PIXL3<380.7 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.63E+04 115807 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
89051 71359 0 17692 0 0
Writing events file
71359 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
89051 71359 0 17692 0 0
in 5157.68 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 71359
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 98 25376
Flickering pixels iter, pixels & cnts : 1 49 1151
cleaning chip # 1
Hot pixels & counts : 70 17313
Flickering pixels iter, pixels & cnts : 1 38 550
cleaning chip # 2
Hot pixels & counts : 54 11027
Flickering pixels iter, pixels & cnts : 1 40 512
cleaning chip # 3
Hot pixels & counts : 59 13652
Flickering pixels iter, pixels & cnts : 1 29 345
Flickering pixels iter, pixels & cnts : 2 1 3
Number of pixels rejected : 438
Number of (internal) image counts : 71359
Number of image cts rejected (N, %) : 69929 97.9960480
By chip : 0 1 2 3
Pixels rejected : 147 108 94 89
Image counts : 26885 18240 11898 14336
Image cts rejected: 26527 17863 11539 14000
Image cts rej (%) : 98.67 97.93 96.98 97.66
filtering data...
Total counts : 26885 18240 11898 14336
Total cts rejected: 26527 17863 11539 14000
Total cts rej (%) : 98.67 97.93 96.98 97.66
Number of clean counts accepted : 1430
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 438
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad55004000s000112h.evt use_events=no
Wrote cleaned events file to ad55004000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad55004000s000202m.unf into ad55004000s000202m.evtThe sum of the selected column is 2310.2259 The mean of the selected column is 66.006455 The standard deviation of the selected column is 9.0244464 The minimum of selected column is 53.625168 The maximum of selected column is 95.844048 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1823.6931 The mean of the selected column is 52.105519 The standard deviation of the selected column is 7.2114042 The minimum of selected column is 40.906376 The maximum of selected column is 75.218987 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1964.1623 The mean of the selected column is 56.118924 The standard deviation of the selected column is 10.321860 The minimum of selected column is 38.156368 The maximum of selected column is 82.375252 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1958.4436 The mean of the selected column is 55.955531 The standard deviation of the selected column is 9.5483848 The minimum of selected column is 41.156376 The maximum of selected column is 76.281487 The number of points used in calculation is 35-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>38.9 && S0_PIXL0<93 )&& (S0_PIXL1>30.4 && S0_PIXL1<73.7 )&& (S0_PIXL2>25.1 && S0_PIXL2<87 )&& (S0_PIXL3>27.3 && S0_PIXL3<84.6 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.45E+04 69122 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
45708 29603 0 16105 0 0
Writing events file
29603 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
45708 29603 0 16105 0 0
in 2829.73 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 29603
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 82 10313
Flickering pixels iter, pixels & cnts : 1 37 603
cleaning chip # 1
Hot pixels & counts : 59 7194
Flickering pixels iter, pixels & cnts : 1 21 342
cleaning chip # 2
Hot pixels & counts : 40 4362
Flickering pixels iter, pixels & cnts : 1 22 231
cleaning chip # 3
Hot pixels & counts : 51 5839
Flickering pixels iter, pixels & cnts : 1 17 127
Number of pixels rejected : 329
Number of (internal) image counts : 29603
Number of image cts rejected (N, %) : 29011 98.0002060
By chip : 0 1 2 3
Pixels rejected : 119 80 62 68
Image counts : 11065 7687 4748 6103
Image cts rejected: 10916 7536 4593 5966
Image cts rej (%) : 98.65 98.04 96.74 97.76
filtering data...
Total counts : 11065 7687 4748 6103
Total cts rejected: 10916 7536 4593 5966
Total cts rej (%) : 98.65 98.04 96.74 97.76
Number of clean counts accepted : 592
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 329
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55004000s000202m.evt use_events=no
Wrote cleaned events file to ad55004000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad55004000s000301h.unf because of modeThe sum of the selected column is 1436.3484 The mean of the selected column is 478.78280 The standard deviation of the selected column is 68.105981 The minimum of selected column is 414.50134 The maximum of selected column is 550.15802 The number of points used in calculation is 3-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2711.6024 The mean of the selected column is 542.32048 The standard deviation of the selected column is 184.38751 The minimum of selected column is 372.96994 The maximum of selected column is 816.12756 The number of points used in calculation is 5-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2792.6964 The mean of the selected column is 698.17411 The standard deviation of the selected column is 223.69292 The minimum of selected column is 500.43912 The maximum of selected column is 997.72192 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3221.4166 The mean of the selected column is 644.28331 The standard deviation of the selected column is 250.99163 The minimum of selected column is 413.65759 The maximum of selected column is 988.62811 The number of points used in calculation is 5-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>274.4 && S0_PIXL0<683.1 )&& (S0_PIXL1>0.0 && S0_PIXL1<1095.4 )&& (S0_PIXL2>27 && S0_PIXL2<1369.2 )&& (S0_PIXL3>0.0 && S0_PIXL3<1397.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:56:31 0.98E+03 7304 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
2761 1163 0 1598 0 0
Writing events file
1163 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2761 1163 0 1598 0 0
in 108.05 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1163
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 86 406
cleaning chip # 1
Hot pixels & counts : 19 133
Flickering pixels iter, pixels & cnts : 1 48 215
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 13 66
Flickering pixels iter, pixels & cnts : 1 16 52
Number of pixels rejected : 182
Number of (internal) image counts : 1163
Number of image cts rejected (N, %) : 872 74.9785004
By chip : 0 1 2 3
Pixels rejected : 86 67 0 29
Image counts : 547 431 0 185
Image cts rejected: 406 348 0 118
Image cts rej (%) : 74.22 80.74 0.00 63.78
filtering data...
Total counts : 547 431 0 185
Total cts rejected: 406 348 0 118
Total cts rej (%) : 74.22 80.74 0.00 63.78
Number of clean counts accepted : 291
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 182
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55004000s000302h.evt use_events=no
Wrote cleaned events file to ad55004000s000302h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad55004000s000312h.unf into ad55004000s000312h.evtThe sum of the selected column is 1436.3484 The mean of the selected column is 478.78280 The standard deviation of the selected column is 68.105981 The minimum of selected column is 414.50134 The maximum of selected column is 550.15802 The number of points used in calculation is 3-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2711.6024 The mean of the selected column is 542.32048 The standard deviation of the selected column is 184.38751 The minimum of selected column is 372.96994 The maximum of selected column is 816.12756 The number of points used in calculation is 5-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2792.6964 The mean of the selected column is 698.17411 The standard deviation of the selected column is 223.69292 The minimum of selected column is 500.43912 The maximum of selected column is 997.72192 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3221.4166 The mean of the selected column is 644.28331 The standard deviation of the selected column is 250.99163 The minimum of selected column is 413.65759 The maximum of selected column is 988.62811 The number of points used in calculation is 5-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>274.4 && S0_PIXL0<683.1 )&& (S0_PIXL1>0.0 && S0_PIXL1<1095.4 )&& (S0_PIXL2>27 && S0_PIXL2<1369.2 )&& (S0_PIXL3>0.0 && S0_PIXL3<1397.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:56:31 0.98E+03 10914 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000312h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
5140 1751 0 3389 0 0
Writing events file
1751 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5140 1751 0 3389 0 0
in 108.05 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1751
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 134 701
cleaning chip # 1
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 91 492
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 19 120
Flickering pixels iter, pixels & cnts : 1 31 127
Number of pixels rejected : 275
Number of (internal) image counts : 1751
Number of image cts rejected (N, %) : 1440 82.2387238
By chip : 0 1 2 3
Pixels rejected : 134 91 0 50
Image counts : 837 576 0 338
Image cts rejected: 701 492 0 247
Image cts rej (%) : 83.75 85.42 0.00 73.08
filtering data...
Total counts : 837 576 0 338
Total cts rejected: 701 492 0 247
Total cts rej (%) : 83.75 85.42 0.00 73.08
Number of clean counts accepted : 311
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 275
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad55004000s000312h.evt use_events=no
Wrote cleaned events file to ad55004000s000312h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad55004000s000402l.unf into ad55004000s000402l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT LOW 20/04/97 16:52:11 0.38E+03 3004 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s000402l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s000402l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55004000s000402l.evt use_events=no
Wrote cleaned events file to ad55004000s000402l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad55004000s000402l.evt since it contains 0 eventsThe sum of the selected column is 25407.736 The mean of the selected column is 139.60295 The standard deviation of the selected column is 49.727341 The minimum of selected column is 47.687649 The maximum of selected column is 362.65741 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24291.386 The mean of the selected column is 133.46915 The standard deviation of the selected column is 52.945761 The minimum of selected column is 47.422024 The maximum of selected column is 337.34482 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 20660.901 The mean of the selected column is 113.52143 The standard deviation of the selected column is 45.099777 The minimum of selected column is 26.487583 The maximum of selected column is 287.87592 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 20925.960 The mean of the selected column is 114.97780 The standard deviation of the selected column is 38.576685 The minimum of selected column is 31.750101 The maximum of selected column is 243.37576 The number of points used in calculation is 182-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<288.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<292.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<248.8 )&& (S1_PIXL3>0.0 && S1_PIXL3<230.7 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.73E+04 188988 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
98209 77350 0 20859 0 0
Writing events file
77350 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
98209 77350 0 20859 0 0
in 5571.77 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 77350
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 88 19757
Flickering pixels iter, pixels & cnts : 1 69 1328
cleaning chip # 1
Hot pixels & counts : 97 18904
Flickering pixels iter, pixels & cnts : 1 86 1617
cleaning chip # 2
Hot pixels & counts : 87 18427
Flickering pixels iter, pixels & cnts : 1 85 1619
cleaning chip # 3
Hot pixels & counts : 73 13326
Flickering pixels iter, pixels & cnts : 1 79 1415
Number of pixels rejected : 664
Number of (internal) image counts : 77350
Number of image cts rejected (N, %) : 76393 98.7627640
By chip : 0 1 2 3
Pixels rejected : 157 183 172 152
Image counts : 21277 20779 20322 14972
Image cts rejected: 21085 20521 20046 14741
Image cts rej (%) : 99.10 98.76 98.64 98.46
filtering data...
Total counts : 21277 20779 20322 14972
Total cts rejected: 21085 20521 20046 14741
Total cts rej (%) : 99.10 98.76 98.64 98.46
Number of clean counts accepted : 957
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 664
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55004000s100102h.evt use_events=no
Wrote cleaned events file to ad55004000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad55004000s100112h.unf into ad55004000s100112h.evtThe sum of the selected column is 25407.736 The mean of the selected column is 139.60295 The standard deviation of the selected column is 49.727341 The minimum of selected column is 47.687649 The maximum of selected column is 362.65741 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24291.386 The mean of the selected column is 133.46915 The standard deviation of the selected column is 52.945761 The minimum of selected column is 47.422024 The maximum of selected column is 337.34482 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 20660.901 The mean of the selected column is 113.52143 The standard deviation of the selected column is 45.099777 The minimum of selected column is 26.487583 The maximum of selected column is 287.87592 The number of points used in calculation is 182-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 20925.960 The mean of the selected column is 114.97780 The standard deviation of the selected column is 38.576685 The minimum of selected column is 31.750101 The maximum of selected column is 243.37576 The number of points used in calculation is 182-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<288.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<292.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<248.8 )&& (S1_PIXL3>0.0 && S1_PIXL3<230.7 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.73E+04 220841 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
158187 123743 0 34444 0 0
Writing events file
123743 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
158187 123743 0 34444 0 0
in 5571.77 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 123743
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 103 28945
Flickering pixels iter, pixels & cnts : 1 93 2548
Flickering pixels iter, pixels & cnts : 2 1 3
cleaning chip # 1
Hot pixels & counts : 115 30183
Flickering pixels iter, pixels & cnts : 1 94 2712
cleaning chip # 2
Hot pixels & counts : 109 29619
Flickering pixels iter, pixels & cnts : 1 86 2237
cleaning chip # 3
Hot pixels & counts : 103 24283
Flickering pixels iter, pixels & cnts : 1 71 1669
Flickering pixels iter, pixels & cnts : 2 1 6
Number of pixels rejected : 776
Number of (internal) image counts : 123743
Number of image cts rejected (N, %) : 122205 98.7571030
By chip : 0 1 2 3
Pixels rejected : 197 209 195 175
Image counts : 31809 33290 32301 26343
Image cts rejected: 31496 32895 31856 25958
Image cts rej (%) : 99.02 98.81 98.62 98.54
filtering data...
Total counts : 31809 33290 32301 26343
Total cts rejected: 31496 32895 31856 25958
Total cts rej (%) : 99.02 98.81 98.62 98.54
Number of clean counts accepted : 1538
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 776
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad55004000s100112h.evt use_events=no
Wrote cleaned events file to ad55004000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad55004000s100202m.unf into ad55004000s100202m.evtThe sum of the selected column is 5590.8611 The mean of the selected column is 159.73889 The standard deviation of the selected column is 24.419690 The minimum of selected column is 132.03166 The maximum of selected column is 228.09445 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5123.8284 The mean of the selected column is 146.39510 The standard deviation of the selected column is 17.659290 The minimum of selected column is 120.03162 The maximum of selected column is 188.09433 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4494.2015 The mean of the selected column is 128.40576 The standard deviation of the selected column is 19.026241 The minimum of selected column is 103.31282 The maximum of selected column is 175.84430 The number of points used in calculation is 35-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4552.4203 The mean of the selected column is 130.06915 The standard deviation of the selected column is 18.080989 The minimum of selected column is 103.03157 The maximum of selected column is 171.09428 The number of points used in calculation is 35-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>86.4 && S1_PIXL0<232.9 )&& (S1_PIXL1>93.4 && S1_PIXL1<199.3 )&& (S1_PIXL2>71.3 && S1_PIXL2<185.4 )&& (S1_PIXL3>75.8 && S1_PIXL3<184.3 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.46E+04 106601 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
51716 18955 0 32761 0 0
Writing events file
18955 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
51716 18955 0 32761 0 0
in 1664.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 18955
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 66 4502
Flickering pixels iter, pixels & cnts : 1 59 658
cleaning chip # 1
Hot pixels & counts : 60 3703
Flickering pixels iter, pixels & cnts : 1 70 609
cleaning chip # 2
Hot pixels & counts : 70 4733
Flickering pixels iter, pixels & cnts : 1 65 676
cleaning chip # 3
Hot pixels & counts : 51 3131
Flickering pixels iter, pixels & cnts : 1 65 585
Number of pixels rejected : 506
Number of (internal) image counts : 18955
Number of image cts rejected (N, %) : 18597 98.1113129
By chip : 0 1 2 3
Pixels rejected : 125 130 135 116
Image counts : 5233 4400 5516 3806
Image cts rejected: 5160 4312 5409 3716
Image cts rej (%) : 98.61 98.00 98.06 97.64
filtering data...
Total counts : 5233 4400 5516 3806
Total cts rejected: 5160 4312 5409 3716
Total cts rej (%) : 98.61 98.00 98.06 97.64
Number of clean counts accepted : 358
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 506
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55004000s100202m.evt use_events=no
Wrote cleaned events file to ad55004000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad55004000s100302l.unf into ad55004000s100302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT LOW 20/04/97 16:23:23 0.36E+04 5776 1111
Processing file: /data/data18/seq_proc/55004000.004/ad55004000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/55004000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/55004000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55004000s100302l.evt use_events=no
Wrote cleaned events file to ad55004000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad55004000s100302l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.unf
Total Good Bad: Region Time Phase Cut
8478 4118 3923 437 0 0
Writing events file
4118 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8478 4118 3923 437 0 0
in 6258.07 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4118 3823 295
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad55004000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 3823 in ad55004000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5492 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.unf
Total Good Bad: Region Time Phase Cut
5492 2048 2643 801 0 0
Writing events file
2048 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5492 2048 2643 801 0 0
in 3167.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
2048 1894 154
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad55004000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 1894 in ad55004000g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1877 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.unf
Total Good Bad: Region Time Phase Cut
1877 166 1220 491 0 0
Writing events file
166 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1877 166 1220 491 0 0
in 208.05 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
166 155 11
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad55004000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 155 in ad55004000g200370l.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.unf
Total Good Bad: Region Time Phase Cut
8136 4404 3246 486 0 0
Writing events file
4404 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8136 4404 3246 486 0 0
in 6258.07 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4404 4082 322
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad55004000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 4082 in ad55004000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5103 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.unf
Total Good Bad: Region Time Phase Cut
5103 2126 2108 869 0 0
Writing events file
2126 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5103 2126 2108 869 0 0
in 3167.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
2126 1959 167
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad55004000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 1959 in ad55004000g300270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.unf
Total Good Bad: Region Time Phase Cut
1713 173 999 541 0 0
Writing events file
173 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1713 173 999 541 0 0
in 208.05 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
173 152 21
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!screen:ASCA > read events ad55004000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad55004000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 152 in ad55004000g300370l.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55004000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2404
Mean RA/DEC/ROLL : 279.6983 -6.1851 291.2404
Pnt RA/DEC/ROLL : 279.6874 -6.1364 291.2404
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 20
Total GTI (secs) : 6258.072
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 761.9974365 761.9974365
20 Percent Complete: Total/live time: 1571.4951172 1571.4951172
30 Percent Complete: Total/live time: 2210.0205078 2210.0205078
40 Percent Complete: Total/live time: 2579.0190430 2579.0190430
50 Percent Complete: Total/live time: 3818.5153809 3818.5153809
60 Percent Complete: Total/live time: 3818.5153809 3818.5153809
70 Percent Complete: Total/live time: 4908.0117188 4908.0117188
80 Percent Complete: Total/live time: 6227.5073242 6227.5073242
90 Percent Complete: Total/live time: 6227.5073242 6227.5073242
100 Percent Complete: Total/live time: 6258.0722656 6258.0722656
Number of attitude steps used: 25
Number of attitude steps avail: 13783
Mean RA/DEC pixel offset: -11.7664 -2.1345
writing expo file: ad55004000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 3779 44 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3823 3779 44 0 0 0
in 6258.07 seconds
Image has 3779 counts for 0.6039 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 1424 44 0 0 2355
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3823 1424 44 0 0 2355
in 6258.07 seconds
Image has 1424 counts for 0.2275 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 2373 44 0 0 1406
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3823 2373 44 0 0 1406
in 6258.07 seconds
Image has 2373 counts for 0.3792 counts/sec
Command not found; type ? for a command listing
!ad55004000g200170h:ASCA >
!ad55004000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g200170h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g200170h:ASCA > read events ad55004000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g200170h:ASCA-GIS2-PH > set image sky
!ad55004000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad55004000g200170h:ASCA-GIS2-PH > extract image
!ad55004000g200170h:ASCA-GIS2-PH > save image outfile=ad55004000g200170h.img
Wrote image to file ad55004000g200170h.img
!ad55004000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad55004000g200170h:ASCA-GIS2-PH > extract image
!ad55004000g200170h:ASCA-GIS2-PH > save image outfile=ad55004000g200170h_lo.img
Wrote image to file ad55004000g200170h_lo.img
!ad55004000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad55004000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g200170h:ASCA-GIS2-PH > extract image
!ad55004000g200170h:ASCA-GIS2-PH > save image outfile=ad55004000g200170h_hi.img
Wrote image to file ad55004000g200170h_hi.img
!ad55004000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad55004000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad55004000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2401
Mean RA/DEC/ROLL : 279.6996 -6.1856 291.2401
Pnt RA/DEC/ROLL : 279.6007 -6.1411 291.2401
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 7
Total GTI (secs) : 3167.980
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 381.0000610 381.0000610
20 Percent Complete: Total/live time: 736.9990845 736.9990845
30 Percent Complete: Total/live time: 1140.9978027 1140.9978027
40 Percent Complete: Total/live time: 1436.9968262 1436.9968262
50 Percent Complete: Total/live time: 1740.9958496 1740.9958496
60 Percent Complete: Total/live time: 2096.0034180 2096.0034180
70 Percent Complete: Total/live time: 2300.9826660 2300.9826660
80 Percent Complete: Total/live time: 2572.9819336 2572.9819336
90 Percent Complete: Total/live time: 3112.9799805 3112.9799805
100 Percent Complete: Total/live time: 3167.9799805 3167.9799805
Number of attitude steps used: 24
Number of attitude steps avail: 1168
Mean RA/DEC pixel offset: -11.8136 -3.0307
writing expo file: ad55004000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 1871 23 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1894 1871 23 0 0 0
in 3167.98 seconds
Image has 1871 counts for 0.5906 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 645 23 0 0 1226
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1894 645 23 0 0 1226
in 3167.98 seconds
Image has 645 counts for 0.2036 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 1232 23 0 0 639
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1894 1232 23 0 0 639
in 3167.98 seconds
Image has 1232 counts for 0.3889 counts/sec
Command not found; type ? for a command listing
!ad55004000g200270m:ASCA >
!ad55004000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g200270m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g200270m:ASCA > read events ad55004000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g200270m:ASCA-GIS2-PH > set image sky
!ad55004000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad55004000g200270m:ASCA-GIS2-PH > extract image
!ad55004000g200270m:ASCA-GIS2-PH > save image outfile=ad55004000g200270m.img
Wrote image to file ad55004000g200270m.img
!ad55004000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad55004000g200270m:ASCA-GIS2-PH > extract image
!ad55004000g200270m:ASCA-GIS2-PH > save image outfile=ad55004000g200270m_lo.img
Wrote image to file ad55004000g200270m_lo.img
!ad55004000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad55004000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g200270m:ASCA-GIS2-PH > extract image
!ad55004000g200270m:ASCA-GIS2-PH > save image outfile=ad55004000g200270m_hi.img
Wrote image to file ad55004000g200270m_hi.img
!ad55004000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad55004000g200370l.expo
ASCAEXPO_V0.9b
reading data file: ad55004000g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2400
Mean RA/DEC/ROLL : 279.6924 -6.1834 291.2400
Pnt RA/DEC/ROLL : 279.7031 -6.1388 291.2400
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 1
Total GTI (secs) : 208.046
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 60.9998055 60.9998055
20 Percent Complete: Total/live time: 208.0464478 208.0464478
100 Percent Complete: Total/live time: 208.0464478 208.0464478
Number of attitude steps used: 2
Number of attitude steps avail: 16
Mean RA/DEC pixel offset: -5.7664 -1.3457
writing expo file: ad55004000g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g200370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g200370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 155 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 153 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
155 153 2 0 0 0
in 208.05 seconds
Image has 153 counts for 0.7354 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 53 2 0 0 100
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
155 53 2 0 0 100
in 208.05 seconds
Image has 53 counts for 0.2548 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 100 2 0 0 53
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
155 100 2 0 0 53
in 208.05 seconds
Image has 100 counts for 0.4807 counts/sec
Command not found; type ? for a command listing
!ad55004000g200370l:ASCA >
!ad55004000g200370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g200370l:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g200370l:ASCA > read events ad55004000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g200370l:ASCA-GIS2-PH > set image sky
!ad55004000g200370l:ASCA-GIS2-PH > filter region corner_point.reg
!ad55004000g200370l:ASCA-GIS2-PH > extract image
!ad55004000g200370l:ASCA-GIS2-PH > save image outfile=ad55004000g200370l.img
Wrote image to file ad55004000g200370l.img
!ad55004000g200370l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad55004000g200370l:ASCA-GIS2-PH > extract image
!ad55004000g200370l:ASCA-GIS2-PH > save image outfile=ad55004000g200370l_lo.img
Wrote image to file ad55004000g200370l_lo.img
!ad55004000g200370l:ASCA-GIS2-PH > clear pha_cut
!ad55004000g200370l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g200370l:ASCA-GIS2-PH > extract image
!ad55004000g200370l:ASCA-GIS2-PH > save image outfile=ad55004000g200370l_hi.img
Wrote image to file ad55004000g200370l_hi.img
!ad55004000g200370l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad55004000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55004000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2412
Mean RA/DEC/ROLL : 279.6916 -6.1611 291.2412
Pnt RA/DEC/ROLL : 279.6941 -6.1603 291.2412
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 20
Total GTI (secs) : 6258.073
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 761.9974365 761.9974365
20 Percent Complete: Total/live time: 1571.4951172 1571.4951172
30 Percent Complete: Total/live time: 2210.0205078 2210.0205078
40 Percent Complete: Total/live time: 2579.0190430 2579.0190430
50 Percent Complete: Total/live time: 3818.5153809 3818.5153809
60 Percent Complete: Total/live time: 3818.5153809 3818.5153809
70 Percent Complete: Total/live time: 4908.0117188 4908.0117188
80 Percent Complete: Total/live time: 6227.5073242 6227.5073242
90 Percent Complete: Total/live time: 6227.5073242 6227.5073242
100 Percent Complete: Total/live time: 6258.0722656 6258.0722656
Number of attitude steps used: 25
Number of attitude steps avail: 13783
Mean RA/DEC pixel offset: -0.1709 -0.9826
writing expo file: ad55004000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 4037 45 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4082 4037 45 0 0 0
in 6258.07 seconds
Image has 4037 counts for 0.6451 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 1520 45 0 0 2517
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4082 1520 45 0 0 2517
in 6258.07 seconds
Image has 1520 counts for 0.2429 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 2539 45 0 0 1498
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4082 2539 45 0 0 1498
in 6258.07 seconds
Image has 2539 counts for 0.4057 counts/sec
Command not found; type ? for a command listing
!ad55004000g300170h:ASCA >
!ad55004000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g300170h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g300170h:ASCA > read events ad55004000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g300170h:ASCA-GIS3-PH > set image sky
!ad55004000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad55004000g300170h:ASCA-GIS3-PH > extract image
!ad55004000g300170h:ASCA-GIS3-PH > save image outfile=ad55004000g300170h.img
Wrote image to file ad55004000g300170h.img
!ad55004000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad55004000g300170h:ASCA-GIS3-PH > extract image
!ad55004000g300170h:ASCA-GIS3-PH > save image outfile=ad55004000g300170h_lo.img
Wrote image to file ad55004000g300170h_lo.img
!ad55004000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad55004000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g300170h:ASCA-GIS3-PH > extract image
!ad55004000g300170h:ASCA-GIS3-PH > save image outfile=ad55004000g300170h_hi.img
Wrote image to file ad55004000g300170h_hi.img
!ad55004000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad55004000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad55004000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2408
Mean RA/DEC/ROLL : 279.6929 -6.1617 291.2408
Pnt RA/DEC/ROLL : 279.6074 -6.1650 291.2408
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 7
Total GTI (secs) : 3167.980
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 381.0000610 381.0000610
20 Percent Complete: Total/live time: 736.9990845 736.9990845
30 Percent Complete: Total/live time: 1140.9978027 1140.9978027
40 Percent Complete: Total/live time: 1436.9968262 1436.9968262
50 Percent Complete: Total/live time: 1740.9958496 1740.9958496
60 Percent Complete: Total/live time: 2096.0034180 2096.0034180
70 Percent Complete: Total/live time: 2300.9826660 2300.9826660
80 Percent Complete: Total/live time: 2572.9819336 2572.9819336
90 Percent Complete: Total/live time: 3112.9799805 3112.9799805
100 Percent Complete: Total/live time: 3167.9799805 3167.9799805
Number of attitude steps used: 24
Number of attitude steps avail: 1168
Mean RA/DEC pixel offset: -0.2383 -1.8809
writing expo file: ad55004000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 1939 20 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1959 1939 20 0 0 0
in 3167.98 seconds
Image has 1939 counts for 0.6121 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 697 20 0 0 1242
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1959 697 20 0 0 1242
in 3167.98 seconds
Image has 697 counts for 0.2200 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 1248 20 0 0 691
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1959 1248 20 0 0 691
in 3167.98 seconds
Image has 1248 counts for 0.3939 counts/sec
Command not found; type ? for a command listing
!ad55004000g300270m:ASCA >
!ad55004000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g300270m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g300270m:ASCA > read events ad55004000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g300270m:ASCA-GIS3-PH > set image sky
!ad55004000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad55004000g300270m:ASCA-GIS3-PH > extract image
!ad55004000g300270m:ASCA-GIS3-PH > save image outfile=ad55004000g300270m.img
Wrote image to file ad55004000g300270m.img
!ad55004000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad55004000g300270m:ASCA-GIS3-PH > extract image
!ad55004000g300270m:ASCA-GIS3-PH > save image outfile=ad55004000g300270m_lo.img
Wrote image to file ad55004000g300270m_lo.img
!ad55004000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad55004000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g300270m:ASCA-GIS3-PH > extract image
!ad55004000g300270m:ASCA-GIS3-PH > save image outfile=ad55004000g300270m_hi.img
Wrote image to file ad55004000g300270m_hi.img
!ad55004000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad55004000g300370l.expo
ASCAEXPO_V0.9b
reading data file: ad55004000g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2408
Mean RA/DEC/ROLL : 279.6855 -6.1594 291.2408
Pnt RA/DEC/ROLL : 279.7098 -6.1628 291.2408
Image rebin factor : 1
Attitude Records : 18017
GTI intervals : 1
Total GTI (secs) : 208.046
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 60.9998055 60.9998055
20 Percent Complete: Total/live time: 208.0464478 208.0464478
100 Percent Complete: Total/live time: 208.0464478 208.0464478
Number of attitude steps used: 2
Number of attitude steps avail: 16
Mean RA/DEC pixel offset: 0.2729 -0.7458
writing expo file: ad55004000g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000g300370l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000g300370l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
in 208.05 seconds
Image has 152 counts for 0.7306 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 52 0 0 0 100
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
152 52 0 0 0 100
in 208.05 seconds
Image has 52 counts for 0.2499 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 100 0 0 0 52
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
152 100 0 0 0 52
in 208.05 seconds
Image has 100 counts for 0.4807 counts/sec
Command not found; type ? for a command listing
!ad55004000g300370l:ASCA >
!ad55004000g300370l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000g300370l:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000g300370l:ASCA > read events ad55004000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000g300370l:ASCA-GIS3-PH > set image sky
!ad55004000g300370l:ASCA-GIS3-PH > filter region corner_point.reg
!ad55004000g300370l:ASCA-GIS3-PH > extract image
!ad55004000g300370l:ASCA-GIS3-PH > save image outfile=ad55004000g300370l.img
Wrote image to file ad55004000g300370l.img
!ad55004000g300370l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad55004000g300370l:ASCA-GIS3-PH > extract image
!ad55004000g300370l:ASCA-GIS3-PH > save image outfile=ad55004000g300370l_lo.img
Wrote image to file ad55004000g300370l_lo.img
!ad55004000g300370l:ASCA-GIS3-PH > clear pha_cut
!ad55004000g300370l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55004000g300370l:ASCA-GIS3-PH > extract image
!ad55004000g300370l:ASCA-GIS3-PH > save image outfile=ad55004000g300370l_hi.img
Wrote image to file ad55004000g300370l_hi.img
!ad55004000g300370l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad55004000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad55004000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2423
Mean RA/DEC/ROLL : 279.6809 -6.1787 291.2423
Pnt RA/DEC/ROLL : 279.7052 -6.1426 291.2423
Image rebin factor : 4
Attitude Records : 18017
Hot Pixels : 410
GTI intervals : 17
Total GTI (secs) : 5157.676
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 576.4980469 576.4980469
20 Percent Complete: Total/live time: 1224.9645996 1224.9645996
30 Percent Complete: Total/live time: 1883.2749023 1883.2749023
40 Percent Complete: Total/live time: 2322.7316895 2322.7316895
50 Percent Complete: Total/live time: 2842.7302246 2842.7302246
60 Percent Complete: Total/live time: 3538.2280273 3538.2280273
70 Percent Complete: Total/live time: 3778.2270508 3778.2270508
80 Percent Complete: Total/live time: 4323.7709961 4323.7709961
90 Percent Complete: Total/live time: 5157.6767578 5157.6767578
100 Percent Complete: Total/live time: 5157.6767578 5157.6767578
Number of attitude steps used: 23
Number of attitude steps avail: 12358
Mean RA/DEC pixel offset: -53.7733 -81.6579
writing expo file: ad55004000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 1067 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1067 1067 0 0 0 0
in 5157.68 seconds
Image has 1067 counts for 0.2069 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 434 0 0 0 633
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1067 434 0 0 0 633
in 5157.68 seconds
Image has 434 counts for 8.4146E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 634 0 0 0 433
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1067 634 0 0 0 433
in 5157.68 seconds
Image has 634 counts for 0.1229 counts/sec
Command not found; type ? for a command listing
!ad55004000s000102h:ASCA >
!ad55004000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000s000102h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000s000102h:ASCA > read events ad55004000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad55004000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55004000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000102h.img
Wrote image to file ad55004000s000102h.img
!ad55004000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55004000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000102h_lo.img
Wrote image to file ad55004000s000102h_lo.img
!ad55004000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55004000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55004000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000102h_hi.img
Wrote image to file ad55004000s000102h_hi.img
!ad55004000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55004000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad55004000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2420
Mean RA/DEC/ROLL : 279.6811 -6.1793 291.2420
Pnt RA/DEC/ROLL : 279.6510 -6.1455 291.2420
Image rebin factor : 4
Attitude Records : 18017
Hot Pixels : 329
GTI intervals : 9
Total GTI (secs) : 2829.730
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 440.9961548 440.9961548
20 Percent Complete: Total/live time: 632.9956055 632.9956055
30 Percent Complete: Total/live time: 1056.0000000 1056.0000000
40 Percent Complete: Total/live time: 1264.9934082 1264.9934082
50 Percent Complete: Total/live time: 1500.9925537 1500.9925537
60 Percent Complete: Total/live time: 1792.0000000 1792.0000000
70 Percent Complete: Total/live time: 2246.6718750 2246.6718750
80 Percent Complete: Total/live time: 2494.6711426 2494.6711426
90 Percent Complete: Total/live time: 2778.6701660 2778.6701660
100 Percent Complete: Total/live time: 2829.7297363 2829.7297363
Number of attitude steps used: 21
Number of attitude steps avail: 1143
Mean RA/DEC pixel offset: -51.9459 -94.0345
writing expo file: ad55004000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.28E+04 592 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 592 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
592 592 0 0 0 0
in 2829.73 seconds
Image has 592 counts for 0.2092 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 257 0 0 0 335
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
592 257 0 0 0 335
in 2829.73 seconds
Image has 257 counts for 9.0821E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 336 0 0 0 256
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
592 336 0 0 0 256
in 2829.73 seconds
Image has 336 counts for 0.1187 counts/sec
Command not found; type ? for a command listing
!ad55004000s000202m:ASCA >
!ad55004000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000s000202m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000s000202m:ASCA > read events ad55004000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad55004000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55004000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000202m.img
Wrote image to file ad55004000s000202m.img
!ad55004000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55004000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000202m_lo.img
Wrote image to file ad55004000s000202m_lo.img
!ad55004000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55004000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55004000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000202m_hi.img
Wrote image to file ad55004000s000202m_hi.img
!ad55004000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55004000s000302h.expo
ASCAEXPO_V0.9b
reading data file: ad55004000s000302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2425
Mean RA/DEC/ROLL : 279.6791 -6.1777 291.2425
Pnt RA/DEC/ROLL : 279.7129 -6.1448 291.2425
Image rebin factor : 4
Attitude Records : 18017
Hot Pixels : 182
GTI intervals : 1
Total GTI (secs) : 108.046
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 108.0459824 108.0459824
100 Percent Complete: Total/live time: 108.0459824 108.0459824
Number of attitude steps used: 2
Number of attitude steps avail: 307
Mean RA/DEC pixel offset: -25.4118 -44.1188
writing expo file: ad55004000s000302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000s000302h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000s000302h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:56:31 0.11E+03 291 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.evt
Total Good Bad: Region Time Phase Cut
291 291 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
291 291 0 0 0 0
in 108.05 seconds
Image has 291 counts for 2.693 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.evt
Total Good Bad: Region Time Phase Cut
291 267 0 0 0 24
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
291 267 0 0 0 24
in 108.05 seconds
Image has 267 counts for 2.471 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.evt
Total Good Bad: Region Time Phase Cut
291 24 0 0 0 267
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
291 24 0 0 0 267
in 108.05 seconds
Image has 24 counts for 0.2221 counts/sec
Command not found; type ? for a command listing
!ad55004000s000302h:ASCA >
!ad55004000s000302h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000s000302h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000s000302h:ASCA > read events ad55004000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000s000302h:ASCA-SIS0-BRIGHT > set image sky
!ad55004000s000302h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55004000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000302h.img
Wrote image to file ad55004000s000302h.img
!ad55004000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55004000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000302h_lo.img
Wrote image to file ad55004000s000302h_lo.img
!ad55004000s000302h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55004000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55004000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad55004000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad55004000s000302h_hi.img
Wrote image to file ad55004000s000302h_hi.img
!ad55004000s000302h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55004000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad55004000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2407
Mean RA/DEC/ROLL : 279.6960 -6.1738 291.2407
Pnt RA/DEC/ROLL : 279.6900 -6.1474 291.2407
Image rebin factor : 4
Attitude Records : 18017
Hot Pixels : 664
GTI intervals : 16
Total GTI (secs) : 5571.770
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 771.4975586 771.4975586
20 Percent Complete: Total/live time: 1256.9645996 1256.9645996
30 Percent Complete: Total/live time: 1895.7438965 1895.7438965
40 Percent Complete: Total/live time: 2370.7316895 2370.7316895
50 Percent Complete: Total/live time: 2890.7302246 2890.7302246
60 Percent Complete: Total/live time: 3586.2280273 3586.2280273
70 Percent Complete: Total/live time: 3961.2268066 3961.2268066
80 Percent Complete: Total/live time: 4627.7709961 4627.7709961
90 Percent Complete: Total/live time: 5571.7700195 5571.7700195
100 Percent Complete: Total/live time: 5571.7700195 5571.7700195
Number of attitude steps used: 23
Number of attitude steps avail: 12609
Mean RA/DEC pixel offset: -58.0208 -12.9388
writing expo file: ad55004000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 957 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
957 957 0 0 0 0
in 5571.77 seconds
Image has 957 counts for 0.1718 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 450 0 0 0 507
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
957 450 0 0 0 507
in 5571.77 seconds
Image has 450 counts for 8.0764E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 512 0 0 0 445
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
957 512 0 0 0 445
in 5571.77 seconds
Image has 512 counts for 9.1892E-02 counts/sec
Command not found; type ? for a command listing
!ad55004000s100102h:ASCA >
!ad55004000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000s100102h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000s100102h:ASCA > read events ad55004000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad55004000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad55004000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100102h.img
Wrote image to file ad55004000s100102h.img
!ad55004000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad55004000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100102h_lo.img
Wrote image to file ad55004000s100102h_lo.img
!ad55004000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad55004000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55004000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100102h_hi.img
Wrote image to file ad55004000s100102h_hi.img
!ad55004000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad55004000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad55004000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970420_1510.2120
making an exposure map...
Aspect RA/DEC/ROLL : 279.6940 -6.1602 291.2404
Mean RA/DEC/ROLL : 279.6974 -6.1744 291.2404
Pnt RA/DEC/ROLL : 279.5949 -6.1529 291.2404
Image rebin factor : 4
Attitude Records : 18017
Hot Pixels : 506
GTI intervals : 9
Total GTI (secs) : 1664.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 204.9966583 204.9966583
20 Percent Complete: Total/live time: 540.9913330 540.9913330
30 Percent Complete: Total/live time: 540.9913330 540.9913330
40 Percent Complete: Total/live time: 784.9429932 784.9429932
50 Percent Complete: Total/live time: 1080.9421387 1080.9421387
60 Percent Complete: Total/live time: 1080.9421387 1080.9421387
70 Percent Complete: Total/live time: 1328.9414062 1328.9414062
80 Percent Complete: Total/live time: 1612.9405518 1612.9405518
90 Percent Complete: Total/live time: 1612.9405518 1612.9405518
100 Percent Complete: Total/live time: 1664.0001221 1664.0001221
Number of attitude steps used: 17
Number of attitude steps avail: 843
Mean RA/DEC pixel offset: -57.4921 -20.7105
writing expo file: ad55004000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55004000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55004000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.17E+04 358 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 358 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
358 358 0 0 0 0
in 1664.00 seconds
Image has 358 counts for 0.2151 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 245 0 0 0 113
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
358 245 0 0 0 113
in 1664.00 seconds
Image has 245 counts for 0.1472 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 113 0 0 0 245
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
358 113 0 0 0 245
in 1664.00 seconds
Image has 113 counts for 6.7909E-02 counts/sec
Command not found; type ? for a command listing
!ad55004000s100202m:ASCA >
!ad55004000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55004000s100202m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!ad55004000s100202m:ASCA > read events ad55004000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!ad55004000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad55004000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad55004000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100202m.img
Wrote image to file ad55004000s100202m.img
!ad55004000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad55004000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100202m_lo.img
Wrote image to file ad55004000s100202m_lo.img
!ad55004000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad55004000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55004000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad55004000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad55004000s100202m_hi.img
Wrote image to file ad55004000s100202m_hi.img
!ad55004000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad55004000s000102h.expo ad55004000s000202m.expo ad55004000s000302h.expo ad55004000s100102h.expo ad55004000s100202m.expo-> Summing the following images to produce ad55004000sis32002_all.totsky
ad55004000s000102h.img ad55004000s000202m.img ad55004000s000302h.img ad55004000s100102h.img ad55004000s100202m.img-> Summing the following images to produce ad55004000sis32002_lo.totsky
ad55004000s000102h_lo.img ad55004000s000202m_lo.img ad55004000s000302h_lo.img ad55004000s100102h_lo.img ad55004000s100202m_lo.img-> Summing the following images to produce ad55004000sis32002_hi.totsky
ad55004000s000102h_hi.img ad55004000s000202m_hi.img ad55004000s000302h_hi.img ad55004000s100102h_hi.img ad55004000s100202m_hi.img-> Running XIMAGE to create ad55004000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55004000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 5.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 5 min: 0 ![2]XIMAGE> read/exp_map ad55004000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 255.520 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 255 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 29.0000 29 0 ![9]XIMAGE> exit-> Summing gis images
ad55004000g200170h.expo ad55004000g200270m.expo ad55004000g200370l.expo ad55004000g300170h.expo ad55004000g300270m.expo ad55004000g300370l.expo-> Summing the following images to produce ad55004000gis25670_all.totsky
ad55004000g200170h.img ad55004000g200270m.img ad55004000g200370l.img ad55004000g300170h.img ad55004000g300270m.img ad55004000g300370l.img-> Summing the following images to produce ad55004000gis25670_lo.totsky
ad55004000g200170h_lo.img ad55004000g200270m_lo.img ad55004000g200370l_lo.img ad55004000g300170h_lo.img ad55004000g300270m_lo.img ad55004000g300370l_lo.img-> Summing the following images to produce ad55004000gis25670_hi.totsky
ad55004000g200170h_hi.img ad55004000g200270m_hi.img ad55004000g200370l_hi.img ad55004000g300170h_hi.img ad55004000g300270m_hi.img ad55004000g300370l_hi.img-> Running XIMAGE to create ad55004000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55004000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 5.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 5 min: 0 ![2]XIMAGE> read/exp_map ad55004000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 321.137 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 321 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 5.00000 50 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 30.0000 30 0 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55004000gis25670.src
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55004000sis32002.src
1 ad55004000s000102h.evt 1659 1 ad55004000s000202m.evt 1659 2 ad55004000s000302h.evt 291-> Fetching SIS0_OFFCHIP.1
ad55004000s000102h.evt ad55004000s000202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
2 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.28E+04 592 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 1038 29 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 565 27 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1659 1603 56 0 0 0
in 7987.41 seconds
Spectrum has 1603 counts for 0.2007 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7987.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000s010102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 1038 29 0 0 0
Writing events file
1038 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 565 27 0 0 0
Writing events file
1603 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1659 1603 56 0 0 0
in 7987.41 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad55004000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad55004000s010102_0.pi group=yes
Wrote spectrum to ad55004000s010102_0.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad55004000s010102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7987.4 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 25 are grouped by a factor 10 ... 26 - 27 are grouped by a factor 2 ... 28 - 31 are grouped by a factor 4 ... 32 - 34 are grouped by a factor 3 ... 35 - 38 are grouped by a factor 4 ... 39 - 41 are grouped by a factor 3 ... 42 - 45 are grouped by a factor 4 ... 46 - 48 are grouped by a factor 3 ... 49 - 52 are grouped by a factor 4 ... 53 - 70 are grouped by a factor 3 ... 71 - 82 are grouped by a factor 4 ... 83 - 88 are grouped by a factor 6 ... 89 - 93 are grouped by a factor 5 ... 94 - 105 are grouped by a factor 6 ... 106 - 110 are grouped by a factor 5 ... 111 - 116 are grouped by a factor 6 ... 117 - 123 are grouped by a factor 7 ... 124 - 132 are grouped by a factor 9 ... 133 - 139 are grouped by a factor 7 ... 140 - 155 are grouped by a factor 8 ... 156 - 169 are grouped by a factor 14 ... 170 - 201 are grouped by a factor 16 ... 202 - 224 are grouped by a factor 23 ... 225 - 261 are grouped by a factor 37 ... 262 - 314 are grouped by a factor 53 ... 315 - 457 are grouped by a factor 143 ... 458 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000s010102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:29:47 0.80E+04 1603 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1603 404 1199 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1603 404 1199 0 0 0
in 7987.41 seconds
Spectrum has 404 counts for 5.0580E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7987.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:29:47 0.80E+04 1603 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1603 427 1176 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1603 427 1176 0 0 0
in 7987.41 seconds
Spectrum has 427 counts for 5.3459E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7987.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:29:47 0.80E+04 1603 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1603 406 1197 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1603 406 1197 0 0 0
in 7987.41 seconds
Spectrum has 406 counts for 5.0830E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7987.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:29:47 0.80E+04 1603 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1603 366 1237 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1603 366 1237 0 0 0
in 7987.41 seconds
Spectrum has 366 counts for 4.5822E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7987.4 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.252027448533999 rmf1.tmp 0.266375545851528 rmf2.tmp 0.253275109170306 rmf3.tmp 0.228321896444167-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.520E-01 * rmf0.tmp
2.664E-01 * rmf1.tmp
2.533E-01 * rmf2.tmp
2.283E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.27
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.23
ASCA SIS0 NONE NONE PI
-> Generating ad55004000s010102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.56100E+03
Weighted mean angle from optical axis = 8.614 arcmin
-> Standard Output From STOOL group_event_files:1 ad55004000s000112h.evt 1430 2 ad55004000s000312h.evt 311-> SIS0_OFFCHIP.1 already present in current directory
ad55004000s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1430 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000112h.evt
Total Good Bad: Region Time Phase Cut
1430 1392 38 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1430 1392 38 0 0 0
in 5157.68 seconds
Spectrum has 1392 counts for 0.2699 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5157.7 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000s010212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000112h.evt
Total Good Bad: Region Time Phase Cut
1430 1392 38 0 0 0
Writing events file
1392 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1430 1392 38 0 0 0
in 5157.68 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad55004000s010212_0.pi group=yes
Wrote spectrum to ad55004000s010212_0.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad55004000s010212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 5157.7 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 45 are grouped by a factor 14 ... 46 - 61 are grouped by a factor 8 ... 62 - 70 are grouped by a factor 9 ... 71 - 78 are grouped by a factor 8 ... 79 - 87 are grouped by a factor 9 ... 88 - 115 are grouped by a factor 7 ... 116 - 123 are grouped by a factor 8 ... 124 - 141 are grouped by a factor 6 ... 142 - 150 are grouped by a factor 9 ... 151 - 163 are grouped by a factor 13 ... 164 - 173 are grouped by a factor 10 ... 174 - 197 are grouped by a factor 12 ... 198 - 212 are grouped by a factor 15 ... 213 - 223 are grouped by a factor 11 ... 224 - 238 are grouped by a factor 15 ... 239 - 256 are grouped by a factor 18 ... 257 - 273 are grouped by a factor 17 ... 274 - 289 are grouped by a factor 16 ... 290 - 309 are grouped by a factor 20 ... 310 - 341 are grouped by a factor 32 ... 342 - 377 are grouped by a factor 36 ... 378 - 417 are grouped by a factor 40 ... 418 - 461 are grouped by a factor 44 ... 462 - 541 are grouped by a factor 80 ... 542 - 694 are grouped by a factor 153 ... 695 - 958 are grouped by a factor 264 ... 959 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000s010212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1392 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1392 347 1045 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1392 347 1045 0 0 0
in 5157.68 seconds
Spectrum has 347 counts for 6.7278E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5157.7 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1392 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1392 368 1024 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1392 368 1024 0 0 0
in 5157.68 seconds
Spectrum has 368 counts for 7.1350E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5157.7 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1392 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1392 350 1042 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1392 350 1042 0 0 0
in 5157.68 seconds
Spectrum has 350 counts for 6.7860E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5157.7 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1392 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1392 327 1065 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1392 327 1065 0 0 0
in 5157.68 seconds
Spectrum has 327 counts for 6.3401E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5157.7 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.249281609195402 rmf1.tmp 0.264367816091954 rmf2.tmp 0.251436781609195 rmf3.tmp 0.234913793103448-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.493E-01 * rmf0.tmp
2.644E-01 * rmf1.tmp
2.514E-01 * rmf2.tmp
2.349E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.26
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.23
ASCA SIS0 NONE NONE PI
-> Generating ad55004000s010212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.35500E+03
Weighted mean angle from optical axis = 8.633 arcmin
-> Standard Output From STOOL group_event_files:1 ad55004000s100102h.evt 1315 1 ad55004000s100202m.evt 1315-> Fetching SIS1_OFFCHIP.1
ad55004000s100102h.evt ad55004000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
2 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.17E+04 358 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 941 16 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 348 10 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1315 1289 26 0 0 0
in 7235.77 seconds
Spectrum has 1289 counts for 0.1781 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7235.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000s110102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 941 16 0 0 0
Writing events file
941 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 348 10 0 0 0
Writing events file
1289 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1315 1289 26 0 0 0
in 7235.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad55004000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad55004000s110102_0.pi group=yes
Wrote spectrum to ad55004000s110102_0.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad55004000s110102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7235.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 25 are grouped by a factor 10 ... 26 - 31 are grouped by a factor 3 ... 32 - 33 are single channels ... 34 - 35 are grouped by a factor 2 ... 36 - 38 are grouped by a factor 3 ... 39 - 50 are grouped by a factor 4 ... 51 - 56 are grouped by a factor 6 ... 57 - 60 are grouped by a factor 4 ... 61 - 65 are grouped by a factor 5 ... 66 - 68 are grouped by a factor 3 ... 69 - 73 are grouped by a factor 5 ... 74 - 80 are grouped by a factor 7 ... 81 - 89 are grouped by a factor 9 ... 90 - 97 are grouped by a factor 8 ... 98 - 106 are grouped by a factor 9 ... 107 - 116 are grouped by a factor 10 ... 117 - 134 are grouped by a factor 9 ... 135 - 149 are grouped by a factor 15 ... 150 - 165 are grouped by a factor 16 ... 166 - 187 are grouped by a factor 22 ... 188 - 216 are grouped by a factor 29 ... 217 - 274 are grouped by a factor 58 ... 275 - 434 are grouped by a factor 160 ... 435 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000s110102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:28:27 0.72E+04 1289 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1289 259 1030 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1289 259 1030 0 0 0
in 7235.77 seconds
Spectrum has 259 counts for 3.5794E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7235.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:28:27 0.72E+04 1289 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1289 339 950 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1289 339 950 0 0 0
in 7235.77 seconds
Spectrum has 339 counts for 4.6851E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7235.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:28:27 0.72E+04 1289 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1289 375 914 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1289 375 914 0 0 0
in 7235.77 seconds
Spectrum has 375 counts for 5.1826E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7235.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:28:27 0.72E+04 1289 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1289 316 973 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1289 316 973 0 0 0
in 7235.77 seconds
Spectrum has 316 counts for 4.3672E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7235.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.200930954228084 rmf1.tmp 0.26299456943367 rmf2.tmp 0.290923196276183 rmf3.tmp 0.245151280062064-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.009E-01 * rmf0.tmp
2.630E-01 * rmf1.tmp
2.909E-01 * rmf2.tmp
2.452E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.20
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.26
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.29
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.25
ASCA SIS1 NONE NONE PI
-> Generating ad55004000s110102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 105 by 134 bins
expanded to 105 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.25800E+03
Weighted mean angle from optical axis = 8.935 arcmin
-> Standard Output From STOOL group_event_files:1 ad55004000s100112h.evt 1538-> SIS1_OFFCHIP.1 already present in current directory
ad55004000s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1538 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100112h.evt
Total Good Bad: Region Time Phase Cut
1538 1511 27 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1538 1511 27 0 0 0
in 5571.77 seconds
Spectrum has 1511 counts for 0.2712 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5571.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000s110212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100112h.evt
Total Good Bad: Region Time Phase Cut
1538 1511 27 0 0 0
Writing events file
1511 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1538 1511 27 0 0 0
in 5571.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad55004000s110212_0.pi group=yes
Wrote spectrum to ad55004000s110212_0.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad55004000s110212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 5571.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 42 are grouped by a factor 10 ... 43 - 46 are grouped by a factor 4 ... 47 - 52 are grouped by a factor 6 ... 53 - 57 are grouped by a factor 5 ... 58 - 61 are grouped by a factor 4 ... 62 - 67 are grouped by a factor 6 ... 68 - 76 are grouped by a factor 9 ... 77 - 82 are grouped by a factor 6 ... 83 - 90 are grouped by a factor 8 ... 91 - 104 are grouped by a factor 7 ... 105 - 112 are grouped by a factor 8 ... 113 - 119 are grouped by a factor 7 ... 120 - 125 are grouped by a factor 6 ... 126 - 132 are grouped by a factor 7 ... 133 - 140 are grouped by a factor 8 ... 141 - 160 are grouped by a factor 10 ... 161 - 172 are grouped by a factor 12 ... 173 - 183 are grouped by a factor 11 ... 184 - 196 are grouped by a factor 13 ... 197 - 208 are grouped by a factor 12 ... 209 - 221 are grouped by a factor 13 ... 222 - 235 are grouped by a factor 14 ... 236 - 252 are grouped by a factor 17 ... 253 - 271 are grouped by a factor 19 ... 272 - 291 are grouped by a factor 20 ... 292 - 317 are grouped by a factor 26 ... 318 - 342 are grouped by a factor 25 ... 343 - 370 are grouped by a factor 28 ... 371 - 416 are grouped by a factor 46 ... 417 - 463 are grouped by a factor 47 ... 464 - 548 are grouped by a factor 85 ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000s110212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1511 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1511 309 1202 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1511 309 1202 0 0 0
in 5571.77 seconds
Spectrum has 309 counts for 5.5458E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5571.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1511 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1511 389 1122 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1511 389 1122 0 0 0
in 5571.77 seconds
Spectrum has 389 counts for 6.9816E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5571.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1511 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1511 436 1075 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1511 436 1075 0 0 0
in 5571.77 seconds
Spectrum has 436 counts for 7.8252E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5571.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1511 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1511 377 1134 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1511 377 1134 0 0 0
in 5571.77 seconds
Spectrum has 377 counts for 6.7663E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 5571.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.204500330906684 rmf1.tmp 0.257445400397088 rmf2.tmp 0.2885506287227 rmf3.tmp 0.249503639973527-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.045E-01 * rmf0.tmp
2.574E-01 * rmf1.tmp
2.886E-01 * rmf2.tmp
2.495E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.20
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.26
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.29
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.25
ASCA SIS1 NONE NONE PI
-> Generating ad55004000s110212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 105 by 134 bins
expanded to 105 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.47000E+03
Weighted mean angle from optical axis = 8.719 arcmin
-> Standard Output From STOOL group_event_files:1 ad55004000g200170h.evt 5872 1 ad55004000g200270m.evt 5872 1 ad55004000g200370l.evt 5872-> GIS2_REGION256.4 already present in current directory
ad55004000g200170h.evt ad55004000g200270m.evt ad55004000g200370l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 155 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 3823 0 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 1894 0 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 155 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5872 5872 0 0 0 0
in 9634.10 seconds
Spectrum has 5872 counts for 0.6095 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 9634.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36888 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad55004000g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad55004000g210170_0.pi group=yes
Wrote spectrum to ad55004000g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad55004000g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad55004000g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 9634.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 23 are grouped by a factor 24 ... 24 - 26 are grouped by a factor 3 ... 27 - 30 are grouped by a factor 4 ... 31 - 35 are grouped by a factor 5 ... 36 - 43 are grouped by a factor 8 ... 44 - 52 are grouped by a factor 9 ... 53 - 62 are grouped by a factor 10 ... 63 - 69 are grouped by a factor 7 ... 70 - 75 are grouped by a factor 6 ... 76 - 78 are grouped by a factor 3 ... 79 - 83 are grouped by a factor 5 ... 84 - 87 are grouped by a factor 4 ... 88 - 90 are grouped by a factor 3 ... 91 - 98 are grouped by a factor 4 ... 99 - 113 are grouped by a factor 3 ... 114 - 115 are grouped by a factor 2 ... 116 - 124 are grouped by a factor 3 ... 125 - 126 are grouped by a factor 2 ... 127 - 132 are grouped by a factor 3 ... 133 - 134 are grouped by a factor 2 ... 135 - 137 are grouped by a factor 3 ... 138 - 163 are grouped by a factor 2 ... 164 - 166 are grouped by a factor 3 ... 167 - 170 are grouped by a factor 2 ... 171 - 173 are grouped by a factor 3 ... 174 - 177 are grouped by a factor 2 ... 178 - 195 are grouped by a factor 3 ... 196 - 199 are grouped by a factor 4 ... 200 - 217 are grouped by a factor 3 ... 218 - 225 are grouped by a factor 4 ... 226 - 228 are grouped by a factor 3 ... 229 - 236 are grouped by a factor 4 ... 237 - 239 are grouped by a factor 3 ... 240 - 259 are grouped by a factor 4 ... 260 - 264 are grouped by a factor 5 ... 265 - 272 are grouped by a factor 4 ... 273 - 277 are grouped by a factor 5 ... 278 - 281 are grouped by a factor 4 ... 282 - 286 are grouped by a factor 5 ... 287 - 290 are grouped by a factor 4 ... 291 - 295 are grouped by a factor 5 ... 296 - 301 are grouped by a factor 6 ... 302 - 305 are grouped by a factor 4 ... 306 - 308 are grouped by a factor 3 ... 309 - 312 are grouped by a factor 4 ... 313 - 317 are grouped by a factor 5 ... 318 - 321 are grouped by a factor 4 ... 322 - 326 are grouped by a factor 5 ... 327 - 333 are grouped by a factor 7 ... 334 - 345 are grouped by a factor 6 ... 346 - 350 are grouped by a factor 5 ... 351 - 356 are grouped by a factor 6 ... 357 - 372 are grouped by a factor 8 ... 373 - 377 are grouped by a factor 5 ... 378 - 384 are grouped by a factor 7 ... 385 - 396 are grouped by a factor 6 ... 397 - 403 are grouped by a factor 7 ... 404 - 413 are grouped by a factor 5 ... 414 - 421 are grouped by a factor 8 ... 422 - 439 are grouped by a factor 9 ... 440 - 455 are grouped by a factor 8 ... 456 - 465 are grouped by a factor 10 ... 466 - 498 are grouped by a factor 11 ... 499 - 508 are grouped by a factor 10 ... 509 - 530 are grouped by a factor 11 ... 531 - 543 are grouped by a factor 13 ... 544 - 555 are grouped by a factor 12 ... 556 - 568 are grouped by a factor 13 ... 569 - 579 are grouped by a factor 11 ... 580 - 609 are grouped by a factor 15 ... 610 - 625 are grouped by a factor 16 ... 626 - 650 are grouped by a factor 25 ... 651 - 674 are grouped by a factor 24 ... 675 - 699 are grouped by a factor 25 ... 700 - 731 are grouped by a factor 32 ... 732 - 768 are grouped by a factor 37 ... 769 - 821 are grouped by a factor 53 ... 822 - 875 are grouped by a factor 54 ... 876 - 931 are grouped by a factor 56 ... 932 - 1012 are grouped by a factor 81 ... 1013 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000g210170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.87200E+03
Weighted mean angle from optical axis = 13.630 arcmin
-> Standard Output From STOOL group_event_files:1 ad55004000g300170h.evt 6193 1 ad55004000g300270m.evt 6193 1 ad55004000g300370l.evt 6193-> GIS3_REGION256.4 already present in current directory
ad55004000g300170h.evt ad55004000g300270m.evt ad55004000g300370l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 4082 0 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 1959 0 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6193 6193 0 0 0 0
in 9634.10 seconds
Spectrum has 6193 counts for 0.6428 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 9634.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36783 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad55004000g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad55004000g310170_0.pi group=yes
Wrote spectrum to ad55004000g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad55004000g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad55004000g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 9634.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 23 are grouped by a factor 24 ... 24 - 28 are grouped by a factor 5 ... 29 - 35 are grouped by a factor 7 ... 36 - 41 are grouped by a factor 6 ... 42 - 48 are grouped by a factor 7 ... 49 - 57 are grouped by a factor 9 ... 58 - 63 are grouped by a factor 6 ... 64 - 71 are grouped by a factor 8 ... 72 - 75 are grouped by a factor 4 ... 76 - 80 are grouped by a factor 5 ... 81 - 88 are grouped by a factor 4 ... 89 - 91 are grouped by a factor 3 ... 92 - 95 are grouped by a factor 4 ... 96 - 97 are grouped by a factor 2 ... 98 - 103 are grouped by a factor 3 ... 104 - 105 are grouped by a factor 2 ... 106 - 117 are grouped by a factor 3 ... 118 - 121 are grouped by a factor 2 ... 122 - 124 are grouped by a factor 3 ... 125 - 128 are grouped by a factor 2 ... 129 - 131 are grouped by a factor 3 ... 132 - 135 are grouped by a factor 2 ... 136 - 141 are grouped by a factor 3 ... 142 - 175 are grouped by a factor 2 ... 176 - 181 are grouped by a factor 3 ... 182 - 185 are grouped by a factor 2 ... 186 - 200 are grouped by a factor 3 ... 201 - 202 are grouped by a factor 2 ... 203 - 205 are grouped by a factor 3 ... 206 - 221 are grouped by a factor 4 ... 222 - 224 are grouped by a factor 3 ... 225 - 240 are grouped by a factor 4 ... 241 - 243 are grouped by a factor 3 ... 244 - 253 are grouped by a factor 5 ... 254 - 273 are grouped by a factor 4 ... 274 - 276 are grouped by a factor 3 ... 277 - 281 are grouped by a factor 5 ... 282 - 284 are grouped by a factor 3 ... 285 - 299 are grouped by a factor 5 ... 300 - 302 are grouped by a factor 3 ... 303 - 307 are grouped by a factor 5 ... 308 - 323 are grouped by a factor 4 ... 324 - 328 are grouped by a factor 5 ... 329 - 336 are grouped by a factor 4 ... 337 - 342 are grouped by a factor 6 ... 343 - 349 are grouped by a factor 7 ... 350 - 354 are grouped by a factor 5 ... 355 - 361 are grouped by a factor 7 ... 362 - 367 are grouped by a factor 6 ... 368 - 374 are grouped by a factor 7 ... 375 - 380 are grouped by a factor 6 ... 381 - 384 are grouped by a factor 4 ... 385 - 391 are grouped by a factor 7 ... 392 - 397 are grouped by a factor 6 ... 398 - 411 are grouped by a factor 7 ... 412 - 417 are grouped by a factor 6 ... 418 - 426 are grouped by a factor 9 ... 427 - 432 are grouped by a factor 6 ... 433 - 448 are grouped by a factor 8 ... 449 - 455 are grouped by a factor 7 ... 456 - 461 are grouped by a factor 6 ... 462 - 468 are grouped by a factor 7 ... 469 - 477 are grouped by a factor 9 ... 478 - 488 are grouped by a factor 11 ... 489 - 500 are grouped by a factor 12 ... 501 - 509 are grouped by a factor 9 ... 510 - 535 are grouped by a factor 13 ... 536 - 546 are grouped by a factor 11 ... 547 - 554 are grouped by a factor 8 ... 555 - 565 are grouped by a factor 11 ... 566 - 577 are grouped by a factor 12 ... 578 - 591 are grouped by a factor 14 ... 592 - 607 are grouped by a factor 16 ... 608 - 630 are grouped by a factor 23 ... 631 - 661 are grouped by a factor 31 ... 662 - 690 are grouped by a factor 29 ... 691 - 720 are grouped by a factor 30 ... 721 - 763 are grouped by a factor 43 ... 764 - 802 are grouped by a factor 39 ... 803 - 845 are grouped by a factor 43 ... 846 - 889 are grouped by a factor 44 ... 890 - 953 are grouped by a factor 64 ... 954 - 1006 are grouped by a factor 53 ... 1007 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55004000g310170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.19300E+03
Weighted mean angle from optical axis = 13.316 arcmin
-> Plotting ad55004000g210170_0_pi.ps from ad55004000g210170_0.pi
XSPEC 9.01 13:30:59 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000g210170_0.pi
Net count rate (cts/s) for file 1 0.6095 +/- 7.9593E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55004000g310170_0_pi.ps from ad55004000g310170_0.pi
XSPEC 9.01 13:31:30 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000g310170_0.pi
Net count rate (cts/s) for file 1 0.6428 +/- 8.1764E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55004000s010102_0_pi.ps from ad55004000s010102_0.pi
XSPEC 9.01 13:31:59 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000s010102_0.pi
Net count rate (cts/s) for file 1 0.2007 +/- 5.1163E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55004000s010212_0_pi.ps from ad55004000s010212_0.pi
XSPEC 9.01 13:32:30 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000s010212_0.pi
Net count rate (cts/s) for file 1 0.2699 +/- 7.4715E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55004000s110102_0_pi.ps from ad55004000s110102_0.pi
XSPEC 9.01 13:33:07 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000s110102_0.pi
Net count rate (cts/s) for file 1 0.1781 +/- 5.1284E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55004000s110212_0_pi.ps from ad55004000s110212_0.pi
XSPEC 9.01 13:33:41 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55004000s110212_0.pi
Net count rate (cts/s) for file 1 0.2712 +/- 7.0523E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
2 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.28E+04 592 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
2 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.28E+04 592 1111
3 GAL_RIDG BRIGHT HIGH 20/04/97 17:56:31 0.11E+03 291 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 1067 0 0 0 0
Writing events file
1067 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 592 0 0 0 0
Writing events file
1659 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.evt
Total Good Bad: Region Time Phase Cut
291 291 0 0 0 0
Writing events file
1950 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1950 1950 0 0 0 0
in 8095.45 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad55004000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad55004000s000302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad55004000s000002_0.lc with binsize 207.575688949762
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:29:47 0.81E+04 1950 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1950 1950 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1950 1950 0 0 0 0
in 8095.45 seconds
Fits light curve has 1950 counts for 0.2409 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > set binsize 207.575688949762
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad55004000s000002_0.lc
Wrote FITS light curve to file ad55004000s000002_0.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad55004000s000002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55004000s000002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_11_N1 Start Time (d) .... 10558 15:39:39.367
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10558 21:03:23.367
No. of Rows ....... 42 Bin Time (s) ...... 207.6
Right Ascension ... 2.7969E+02 Internal time sys.. Converted to TJD
Declination ....... -6.1602E+00 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 94 Newbins of 207.576 (s)
Intv 1 Start10558 15:41:23
Ser.1 Avg 0.2697 Chisq 3509. Var 0.1467 Newbs. 42
Min 0.1397 Max 2.693 expVar 0.1756E-02 Bins 42
Results from Statistical Analysis
Newbin Integration Time (s).. 207.58
Interval Duration (s)........ 19305.
No. of Newbins .............. 42
Average (c/s) ............... 0.26971 +/- 0.65E-02
Standard Deviation (c/s)..... 0.38308
Minimum (c/s)................ 0.13971
Maximum (c/s)................ 2.6933
Variance ((c/s)**2).......... 0.14675 +/- 0.32E-01
Expected Variance ((c/s)**2). 0.17564E-02 +/- 0.39E-03
Third Moment ((c/s)**3)...... 0.33879
Average Deviation (c/s)...... 0.12990
Skewness..................... 6.0266 +/- 0.38
Kurtosis..................... 35.151 +/- 0.76
RMS fractional variation..... 1.4118 +/- 0.16
Chi-Square................... 3509.1 dof 41
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 94 Newbins of 207.576 (s)
Intv 1 Start10558 15:41:23
Ser.1 Avg 0.2697 Chisq 3509. Var 0.1467 Newbs. 42
Min 0.1397 Max 2.693 expVar 0.1756E-02 Bins 42
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=1.6000000000E+01 for ad55004000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
2 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.17E+04 358 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 957 0 0 0 0
Writing events file
957 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 358 0 0 0 0
Writing events file
1315 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1315 1315 0 0 0 0
in 7235.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad55004000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad55004000s100002_0.lc with binsize 275.124316035341
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 15:28:27 0.72E+04 1315 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1315 1315 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1315 1315 0 0 0 0
in 7235.77 seconds
Fits light curve has 1315 counts for 0.1817 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > set binsize 275.124316035341
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad55004000s100002_0.lc
Wrote FITS light curve to file ad55004000s100002_0.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad55004000s100002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55004000s100002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_11_N1 Start Time (d) .... 10558 15:39:39.367
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10558 21:05:31.367
No. of Rows ....... 26 Bin Time (s) ...... 275.1
Right Ascension ... 2.7969E+02 Internal time sys.. Converted to TJD
Declination ....... -6.1602E+00 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 72 Newbins of 275.124 (s)
Intv 1 Start10558 15:41:56
Ser.1 Avg 0.1780 Chisq 83.58 Var 0.2311E-02 Newbs. 26
Min 0.1228 Max 0.3199 expVar 0.7188E-03 Bins 26
Results from Statistical Analysis
Newbin Integration Time (s).. 275.12
Interval Duration (s)........ 19259.
No. of Newbins .............. 26
Average (c/s) ............... 0.17800 +/- 0.54E-02
Standard Deviation (c/s)..... 0.48069E-01
Minimum (c/s)................ 0.12282
Maximum (c/s)................ 0.31986
Variance ((c/s)**2).......... 0.23107E-02 +/- 0.65E-03
Expected Variance ((c/s)**2). 0.71881E-03 +/- 0.20E-03
Third Moment ((c/s)**3)...... 0.15337E-03
Average Deviation (c/s)...... 0.35744E-01
Skewness..................... 1.3809 +/- 0.48
Kurtosis..................... 1.6078 +/- 0.96
RMS fractional variation..... 0.22414 +/- 0.46E-01
Chi-Square................... 83.579 dof 25
Chi-Square Prob of constancy. 0.31047E-07 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.29122E-05 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 72 Newbins of 275.124 (s)
Intv 1 Start10558 15:41:56
Ser.1 Avg 0.1780 Chisq 83.58 Var 0.2311E-02 Newbs. 26
Min 0.1228 Max 0.3199 expVar 0.7188E-03 Bins 26
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad55004000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 155 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 3823 0 0 0 0
Writing events file
3823 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 1894 0 0 0 0
Writing events file
5717 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 155 0 0 0 0
Writing events file
5872 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5872 5872 0 0 0 0
in 9634.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > filter region ad55004000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad55004000g200070_0.lc with binsize 82.0342211481641
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 15:28:43 0.96E+04 5872 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
5872 5872 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5872 5872 0 0 0 0
in 9634.10 seconds
Fits light curve has 5872 counts for 0.6095 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > set binsize 82.0342211481641
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad55004000g200070_0.lc
Wrote FITS light curve to file ad55004000g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad55004000g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55004000g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_11_N1 Start Time (d) .... 10558 15:35:39.365
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10558 21:13:31.367
No. of Rows ....... 117 Bin Time (s) ...... 82.03
Right Ascension ... 2.7969E+02 Internal time sys.. Converted to TJD
Declination ....... -6.1602E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 248 Newbins of 82.0342 (s)
Intv 1 Start10558 15:40:26
Ser.1 Avg 0.6092 Chisq 106.7 Var 0.7096E-02 Newbs. 117
Min 0.3779 Max 0.8044 expVar 0.7778E-02 Bins 117
Results from Statistical Analysis
Newbin Integration Time (s).. 82.034
Interval Duration (s)........ 19934.
No. of Newbins .............. 117
Average (c/s) ............... 0.60920 +/- 0.82E-02
Standard Deviation (c/s)..... 0.84238E-01
Minimum (c/s)................ 0.37789
Maximum (c/s)................ 0.80442
Variance ((c/s)**2).......... 0.70961E-02 +/- 0.93E-03
Expected Variance ((c/s)**2). 0.77781E-02 +/- 0.10E-02
Third Moment ((c/s)**3)...... 0.12131E-03
Average Deviation (c/s)...... 0.67224E-01
Skewness..................... 0.20295 +/- 0.23
Kurtosis.....................-0.14545 +/- 0.45
RMS fractional variation....< 0.10519 (3 sigma)
Chi-Square................... 106.74 dof 116
Chi-Square Prob of constancy. 0.71926 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.13652 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 248 Newbins of 82.0342 (s)
Intv 1 Start10558 15:40:26
Ser.1 Avg 0.6092 Chisq 106.7 Var 0.7096E-02 Newbs. 117
Min 0.3779 Max 0.8044 expVar 0.7778E-02 Bins 117
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad55004000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 4082 0 0 0 0
Writing events file
4082 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 1959 0 0 0 0
Writing events file
6041 events written to the output file
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
Writing events file
6193 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6193 6193 0 0 0 0
in 9634.10 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300370l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > filter region ad55004000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad55004000g300070_0.lc with binsize 77.7821647958226
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 15:28:43 0.96E+04 6193 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/events.tmp
Total Good Bad: Region Time Phase Cut
6193 6193 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6193 6193 0 0 0 0
in 9634.10 seconds
Fits light curve has 6193 counts for 0.6428 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > set binsize 77.7821647958226
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad55004000g300070_0.lc
Wrote FITS light curve to file ad55004000g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad55004000g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55004000g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_11_N1 Start Time (d) .... 10558 15:35:39.365
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10558 21:13:31.367
No. of Rows ....... 125 Bin Time (s) ...... 77.78
Right Ascension ... 2.7969E+02 Internal time sys.. Converted to TJD
Declination ....... -6.1602E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 261 Newbins of 77.7822 (s)
Intv 1 Start10558 15:40:11
Ser.1 Avg 0.6434 Chisq 151.0 Var 0.1044E-01 Newbs. 125
Min 0.4114 Max 0.9771 expVar 0.8644E-02 Bins 125
Results from Statistical Analysis
Newbin Integration Time (s).. 77.782
Interval Duration (s)........ 19990.
No. of Newbins .............. 125
Average (c/s) ............... 0.64336 +/- 0.83E-02
Standard Deviation (c/s)..... 0.10219
Minimum (c/s)................ 0.41141
Maximum (c/s)................ 0.97709
Variance ((c/s)**2).......... 0.10444E-01 +/- 0.13E-02
Expected Variance ((c/s)**2). 0.86443E-02 +/- 0.11E-02
Third Moment ((c/s)**3)...... 0.55999E-03
Average Deviation (c/s)...... 0.78256E-01
Skewness..................... 0.52470 +/- 0.22
Kurtosis..................... 0.58836 +/- 0.44
RMS fractional variation....< 0.67110E-01 (3 sigma)
Chi-Square................... 151.02 dof 124
Chi-Square Prob of constancy. 0.49843E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.90397E-05 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 261 Newbins of 77.7822 (s)
Intv 1 Start10558 15:40:11
Ser.1 Avg 0.6434 Chisq 151.0 Var 0.1044E-01 Newbs. 125
Min 0.4114 Max 0.9771 expVar 0.8644E-02 Bins 125
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad55004000g200170h.evt[2] ad55004000g200270m.evt[2] ad55004000g200370l.evt[2]-> Making L1 light curve of ft970420_1510_2120G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 14206 output records from 14226 good input G2_L1 records.-> Making L1 light curve of ft970420_1510_2120G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 8667 output records from 17133 good input G2_L1 records.-> Merging GTIs from the following files:
ad55004000g300170h.evt[2] ad55004000g300270m.evt[2] ad55004000g300370l.evt[2]-> Making L1 light curve of ft970420_1510_2120G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 13562 output records from 13582 good input G3_L1 records.-> Making L1 light curve of ft970420_1510_2120G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 8506 output records from 16433 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 3823 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.evt
Total Good Bad: Region Time Phase Cut
3823 3823 0 0 0 0
Writing events file
3823 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3823 3823 0 0 0 0
in 6258.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > filter region ad55004000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad55004000g200170h_0.ulc use_events=yes
Wrote events list to file ad55004000g200170h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000g200270m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1894 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.evt
Total Good Bad: Region Time Phase Cut
1894 1894 0 0 0 0
Writing events file
1894 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1894 1894 0 0 0 0
in 3167.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > filter region ad55004000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad55004000g200270m_0.ulc use_events=yes
Wrote events list to file ad55004000g200270m_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000g200370l_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 155 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.evt
Total Good Bad: Region Time Phase Cut
155 155 0 0 0 0
Writing events file
155 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
155 155 0 0 0 0
in 208.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200370l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > filter region ad55004000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad55004000g200370l_0.ulc use_events=yes
Wrote events list to file ad55004000g200370l_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000g300170h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.63E+04 4082 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.evt
Total Good Bad: Region Time Phase Cut
4082 4082 0 0 0 0
Writing events file
4082 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4082 4082 0 0 0 0
in 6258.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > filter region ad55004000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad55004000g300170h_0.ulc use_events=yes
Wrote events list to file ad55004000g300170h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000g300270m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.32E+04 1959 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.evt
Total Good Bad: Region Time Phase Cut
1959 1959 0 0 0 0
Writing events file
1959 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1959 1959 0 0 0 0
in 3167.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > filter region ad55004000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad55004000g300270m_0.ulc use_events=yes
Wrote events list to file ad55004000g300270m_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000g300370l_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.21E+03 152 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.evt
Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
Writing events file
152 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
152 152 0 0 0 0
in 208.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300370l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > filter region ad55004000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad55004000g300370l_0.ulc use_events=yes
Wrote events list to file ad55004000g300370l_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad55004000s000102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.52E+04 1067 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.evt
Total Good Bad: Region Time Phase Cut
1067 1067 0 0 0 0
Writing events file
1067 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1067 1067 0 0 0 0
in 5157.68 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55004000s000102h_0.ulc use_events=yes
Wrote events list to file ad55004000s000102h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55004000s000112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.52E+04 1430 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000112h.evt
Total Good Bad: Region Time Phase Cut
1430 1430 0 0 0 0
Writing events file
1430 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1430 1430 0 0 0 0
in 5157.68 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad55004000s000112h_0.ulc use_events=yes
Wrote events list to file ad55004000s000112h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55004000s000202m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.28E+04 592 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.evt
Total Good Bad: Region Time Phase Cut
592 592 0 0 0 0
Writing events file
592 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
592 592 0 0 0 0
in 2829.73 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55004000s000202m_0.ulc use_events=yes
Wrote events list to file ad55004000s000202m_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55004000s000302h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:56:31 0.11E+03 291 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.evt
Total Good Bad: Region Time Phase Cut
291 291 0 0 0 0
Writing events file
291 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
291 291 0 0 0 0
in 108.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55004000s000302h_0.ulc use_events=yes
Wrote events list to file ad55004000s000302h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55004000s000312h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:56:31 0.11E+03 311 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000312h.evt
Total Good Bad: Region Time Phase Cut
311 311 0 0 0 0
Writing events file
311 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
311 311 0 0 0 0
in 108.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s000312h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55004000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad55004000s000312h_0.ulc use_events=yes
Wrote events list to file ad55004000s000312h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55004000s100102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.56E+04 957 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.evt
Total Good Bad: Region Time Phase Cut
957 957 0 0 0 0
Writing events file
957 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
957 957 0 0 0 0
in 5571.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad55004000s100102h_0.ulc use_events=yes
Wrote events list to file ad55004000s100102h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55004000s100112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.56E+04 1538 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100112h.evt
Total Good Bad: Region Time Phase Cut
1538 1538 0 0 0 0
Writing events file
1538 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1538 1538 0 0 0 0
in 5571.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad55004000s100112h_0.ulc use_events=yes
Wrote events list to file ad55004000s100112h_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55004000s100202m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.17E+04 358 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.evt
Total Good Bad: Region Time Phase Cut
358 358 0 0 0 0
Writing events file
358 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
358 358 0 0 0 0
in 1664.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55004000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad55004000s100202m_0.ulc use_events=yes
Wrote events list to file ad55004000s100202m_0.ulc
Changing Data directory from:
/data/data18/seq_proc/55004000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) ***
total number of superframes: 4549
frame data: 135714479.332723 ---> 135714623.332272
S0, C0, 4 ccd mode; Output File = fr970420_1510.2120_s0c0m4a.fits
frame data: 135714643.332209 ---> 135714787.331761
S0, C1, 4 ccd mode; Output File = fr970420_1510.2120_s0c1m4a.fits
frame data: 135714807.331699 ---> 135714951.33125
S0, C2, 4 ccd mode; Output File = fr970420_1510.2120_s0c2m4a.fits
frame data: 135714971.331188 ---> 135715115.33074
S0, C3, 4 ccd mode; Output File = fr970420_1510.2120_s0c3m4a.fits
Total of 4 sets of frame data are extracted.
-> Processing fr970420_1510.2120_s0c0m4a.fitsDark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970420_1510.2120_s0c0m4a.fits Output zero level image : rdd.tmp Bias level = 0-> Adding keywords to header of fr970420_1510.2120_s0c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970420_1510.2120_s0c1m4a.fits Output zero level image : rdd.tmp Bias level = 0-> Adding keywords to header of fr970420_1510.2120_s0c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970420_1510.2120_s0c2m4a.fits Output zero level image : rdd.tmp Bias level = 0-> Adding keywords to header of fr970420_1510.2120_s0c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970420_1510.2120_s0c3m4a.fits Output zero level image : rdd.tmp Bias level = 0-> Adding keywords to header of fr970420_1510.2120_s0c3m4a.fits
1 ad55004000g200170h.unf 15847 1 ad55004000g200270m.unf 15847 1 ad55004000g200370l.unf 15847-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5492 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5492 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1877 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.unf
Total Good Bad: Region Time Phase Cut
8478 1268 7210 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.unf
Total Good Bad: Region Time Phase Cut
5492 785 4707 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.unf
Total Good Bad: Region Time Phase Cut
1877 380 1497 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15847 2433 13414 0 0 0
in 14259.96 seconds
Spectrum has 2433 counts for 0.1706 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 14260. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > read events ad55004000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad55004000g220170.cal group=yes
Wrote spectrum to ad55004000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 14:15:39 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55004000g220170.cal
Net count rate (cts/s) for file 1 0.1706 +/- 3.4789E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 5.9815E+05 using 84 PHA bins.
Reduced chi-squared = 7768.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 5.9417E+05 using 84 PHA bins.
Reduced chi-squared = 7618.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 5.9417E+05 using 84 PHA bins.
Reduced chi-squared = 7521.
!XSPEC> renorm
Chi-Squared = 601.3 using 84 PHA bins.
Reduced chi-squared = 7.611
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
485.76 0 1.000 5.894 0.1025 4.6404E-02
4.1592E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
259.85 0 1.000 5.872 0.1515 6.5098E-02
3.6917E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
157.39 -1 1.000 5.921 0.1756 8.8974E-02
2.5977E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
132.05 -2 1.000 5.980 0.2025 0.1044
1.5249E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
131.59 -3 1.000 5.972 0.1950 0.1033
1.6394E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
131.57 -4 1.000 5.973 0.1949 0.1035
1.6196E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
131.57 -5 1.000 5.973 0.1946 0.1034
1.6246E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.97288 +/- 0.12727E-01
3 3 2 gaussian/b Sigma 0.194576 +/- 0.13538E-01
4 4 2 gaussian/b norm 0.103412 +/- 0.35111E-02
5 2 3 gaussian/b LineE 6.57617 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.204166 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.624644E-02 +/- 0.24519E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 131.6 using 84 PHA bins.
Reduced chi-squared = 1.665
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55004000g220170.cal peaks at 5.97288 +/- 0.012727 keV1 ad55004000g300170h.unf 14952 1 ad55004000g300270m.unf 14952 1 ad55004000g300370l.unf 14952-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5103 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
2 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5103 1024
3 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.unf
Total Good Bad: Region Time Phase Cut
8136 1043 7093 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.unf
Total Good Bad: Region Time Phase Cut
5103 634 4469 0 0 0
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.unf
Total Good Bad: Region Time Phase Cut
1713 349 1364 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14952 2026 12926 0 0 0
in 14259.96 seconds
Spectrum has 2026 counts for 0.1421 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 14260. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55004000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!xsel:ASCA > read events ad55004000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > read events ad55004000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad55004000g320170.cal group=yes
Wrote spectrum to ad55004000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 14:17:37 26-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55004000g320170.cal
Net count rate (cts/s) for file 1 0.1421 +/- 3.1990E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.2713E+05 using 84 PHA bins.
Reduced chi-squared = 1.0742E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.1867E+05 using 84 PHA bins.
Reduced chi-squared = 1.0496E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.1867E+05 using 84 PHA bins.
Reduced chi-squared = 1.0363E+04
!XSPEC> renorm
Chi-Squared = 802.9 using 84 PHA bins.
Reduced chi-squared = 10.16
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
640.24 0 1.000 5.891 0.1089 3.7204E-02
3.0665E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
264.17 0 1.000 5.857 0.1466 6.4517E-02
2.6366E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
101.08 -1 1.000 5.922 0.1393 9.5358E-02
1.5103E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.899 -2 1.000 5.929 0.1434 0.1018
1.2934E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.839 -3 1.000 5.927 0.1417 0.1017
1.3127E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.838 -4 1.000 5.928 0.1417 0.1017
1.3104E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92753 +/- 0.94119E-02
3 3 2 gaussian/b Sigma 0.141658 +/- 0.12352E-01
4 4 2 gaussian/b norm 0.101701 +/- 0.30311E-02
5 2 3 gaussian/b LineE 6.52624 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.148641 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.310412E-02 +/- 0.16626E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 95.84 using 84 PHA bins.
Reduced chi-squared = 1.213
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55004000g320170.cal peaks at 5.92753 +/- 0.0094119 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.63E+04 107456 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad55004000s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.63E+04 115807 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad55004000s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:29:47 0.45E+04 69122 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s000202m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad55004000s000202m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:56:31 0.98E+03 7304 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s000302h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad55004000s000302h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:56:31 0.98E+03 10914 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s000312h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad55004000s000312h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT LOW 20/04/97 16:52:11 0.38E+03 3004 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s000402l.unf
Total Good Bad: Region Time Phase Cut
3004 3004 0 0 0 0
Writing events file
3004 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3004 3004 0 0 0 0
in 381.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s000402l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55004000s000402l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55004000s000402l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3004
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 28 592
Flickering pixels iter, pixels & cnts : 1 17 132
cleaning chip # 1
Hot pixels & counts : 29 609
Flickering pixels iter, pixels & cnts : 1 15 115
cleaning chip # 2
Hot pixels & counts : 36 686
Flickering pixels iter, pixels & cnts : 1 9 48
cleaning chip # 3
Hot pixels & counts : 32 678
Flickering pixels iter, pixels & cnts : 1 11 62
Number of pixels rejected : 177
Number of (internal) image counts : 3004
Number of image cts rejected (N, %) : 2922 97.2703094
By chip : 0 1 2 3
Pixels rejected : 45 44 45 43
Image counts : 736 736 764 768
Image cts rejected: 724 724 734 740
Image cts rej (%) : 98.37 98.37 96.07 96.35
filtering data...
Total counts : 736 736 764 768
Total cts rejected: 724 724 734 740
Total cts rej (%) : 98.37 98.37 96.07 96.35
Number of clean counts accepted : 82
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 177
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55004000s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 20/04/97 17:16:07 0.73E+04 188988 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad55004000s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 20/04/97 17:16:07 0.73E+04 220841 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad55004000s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 20/04/97 15:28:27 0.46E+04 106601 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000s100202m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad55004000s100202m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT LOW 20/04/97 16:23:23 0.36E+04 5776 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000s100302l.unf
Total Good Bad: Region Time Phase Cut
5776 3232 0 2544 0 0
Writing events file
3232 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5776 3232 0 2544 0 0
in 412.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55004000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55004000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3232
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 28 646
Flickering pixels iter, pixels & cnts : 1 18 143
cleaning chip # 1
Hot pixels & counts : 29 654
Flickering pixels iter, pixels & cnts : 1 18 122
cleaning chip # 2
Hot pixels & counts : 33 748
Flickering pixels iter, pixels & cnts : 1 8 55
cleaning chip # 3
Hot pixels & counts : 31 649
Flickering pixels iter, pixels & cnts : 1 20 134
Number of pixels rejected : 185
Number of (internal) image counts : 3232
Number of image cts rejected (N, %) : 3151 97.4938126
By chip : 0 1 2 3
Pixels rejected : 46 47 41 51
Image counts : 800 800 832 800
Image cts rejected: 789 776 803 783
Image cts rej (%) : 98.62 97.00 96.51 97.88
filtering data...
Total counts : 800 800 832 800
Total cts rejected: 789 776 803 783
Total cts rej (%) : 98.62 97.00 96.51 97.88
Number of clean counts accepted : 81
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 185
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55004000g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad55004000g200170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8478 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200170h.unf
Total Good Bad: Region Time Phase Cut
8478 192 0 8286 0 0
Writing events file
192 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8478 192 0 8286 0 0
in 288.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad55004000g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5492 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad55004000g200270m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5492 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g200270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad55004000g200270m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1877 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad55004000g200370l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1877 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g200370l.unf
Total Good Bad: Region Time Phase Cut
1877 1377 0 500 0 0
Writing events file
1377 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1877 1377 0 500 0 0
in 2047.94 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad55004000g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad55004000g300170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 20/04/97 17:16:17 0.72E+04 8136 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300170h.unf
Total Good Bad: Region Time Phase Cut
8136 185 0 7951 0 0
Writing events file
185 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8136 185 0 7951 0 0
in 288.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad55004000g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5103 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad55004000g300270m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH MEDIUM 20/04/97 15:28:43 0.47E+04 5103 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g300270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad55004000g300270m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad55004000g300370l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH LOW 20/04/97 16:25:47 0.24E+04 1713 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/55004000.004/ad55004000g300370l.unf
Total Good Bad: Region Time Phase Cut
1713 1238 0 475 0 0
Writing events file
1238 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1713 1238 0 475 0 0
in 2047.94 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/55004000.004/
Setting mkf directory to /data/data18/seq_proc/55004000.004/
!earthevents:ASCA > read events ad55004000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/55004000.004/
HK Directory is: /data/data18/seq_proc/55004000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad55004000s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad55004000s000302h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad55004000s000102h.unf
ad55004000s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad55004000s000312h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad55004000s000112h.unf
ad55004000s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad55004000s000301h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad55004000s000101h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files