The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 153201074.336800 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-11-09 03:51:10.33680 Modified Julian Day = 50761.160536305556889-> leapsec.fits already present in current directory
Offset of 153224452.261800 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-11-09 10:20:48.26179 Modified Julian Day = 50761.431114141203579-> Observation begins 153201074.3368 1997-11-09 03:51:10
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 153201074.336600 153224452.261800
Data file start and stop ascatime : 153201074.336600 153224452.261800
Aspecting run start and stop ascatime : 153201074.336734 153224452.261712
Time interval averaged over (seconds) : 23377.924977
Total pointing and manuver time (sec) : 15564.480469 7813.486816
Mean boresight Euler angles : 297.020857 64.635214 191.802080
RA DEC SUN ANGLE
Mean solar position (deg) : 223.45 -16.60
Mean aberration (arcsec) : -7.94 12.98
Mean sat X-axis (deg) : 143.022372 62.189637 100.28
Mean sat Y-axis (deg) : 212.135731 -10.650317 12.50
Mean sat Z-axis (deg) : 297.020857 25.364787 82.96
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 296.778748 25.183512 101.905357 0.060269
Minimum 296.762146 25.160969 101.899391 0.000000
Maximum 296.794098 25.216497 101.932510 2.147354
Sigma (RMS) 0.001028 0.000109 0.002851 0.060780
Number of ASPECT records processed = 26450
Aspecting to RA/DEC : 296.77874756 25.18351173
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 296.779 DEC: 25.184
START TIME: SC 153201074.3367 = UT 1997-11-09 03:51:14
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000113 1.358 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
187.999603 0.352 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
2075.993652 0.196 9C88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 3
4699.984863 0.030 1C8443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 4 3
7803.975098 0.076 DC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 3
10011.967773 0.045 1C8443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 4 3
13543.957031 0.027 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
15803.949219 0.063 1C8443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 4 3
19283.937500 0.049 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
21899.929688 0.108 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
23374.425781 0.207 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
23376.925781 1.212 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
23377.925781 2.147 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 26450
Attitude Steps: 13
Maneuver ACM time: 7813.50 sec
Pointed ACM time: 15564.5 sec
-> Calculating aspect point100 98 count=4 sum1=1188.07 sum2=258.572 sum3=767.245 100 99 count=31 sum1=9207.39 sum2=2004.09 sum3=5946.38 100 100 count=1 sum1=297.007 sum2=64.654 sum3=191.829 101 96 count=1 sum1=297.025 sum2=64.622 sum3=191.805 101 97 count=4 sum1=1188.08 sum2=258.52 sum3=767.202 101 98 count=26406 sum1=7.84314e+06 sum2=1.70676e+06 sum3=5.06472e+06 102 94 count=1 sum1=297.036 sum2=64.602 sum3=191.821 102 95 count=1 sum1=297.032 sum2=64.61 sum3=191.815 102 96 count=1 sum1=297.028 sum2=64.616 sum3=191.809 0 out of 26450 points outside bin structure-> Euler angles: 297.021, 64.6352, 191.802
639.998 second gap between superframes 215 and 216 609.998 second gap between superframes 2134 and 2135 Dropping SF 2239 with inconsistent datamode 0/31 Dropping SF 2245 with corrupted frame indicator Dropping SF 2247 with corrupted frame indicator Dropping SF 2254 with inconsistent datamode 0/31 Dropping SF 2277 with synch code word 0 = 255 not 250 Dropping SF 2289 with invalid bit rate 7 Dropping SF 2338 with inconsistent datamode 0/31 Dropping SF 2434 with inconsistent datamode 0/31 Dropping SF 2455 with inconsistent datamode 0/31 Dropping SF 2507 with inconsistent datamode 0/31 Dropping SF 2562 with invalid bit rate 7 Dropping SF 2609 with invalid bit rate 7 Dropping SF 2622 with inconsistent datamode 0/31 Dropping SF 2770 with inconsistent datamode 0/31 Dropping SF 2772 with inconsistent datamode 0/31 Dropping SF 2812 with invalid bit rate 7 Dropping SF 2831 with inconsistent datamode 0/31 Dropping SF 2887 with inconsistent datamode 0/31 Dropping SF 2901 with inconsistent datamode 0/31 Dropping SF 2902 with inconsistent datamode 0/31 Dropping SF 2941 with corrupted frame indicator Dropping SF 2949 with corrupted frame indicator Dropping SF 2961 with inconsistent datamode 0/31 Dropping SF 3054 with synch code word 0 = 154 not 250 Dropping SF 3057 with inconsistent datamode 0/31 SIS0 coordinate error time=153213660.17139 x=0 y=0 pha[0]=3 chip=0 Dropping SF 3127 with invalid bit rate 7 Dropping SF 3142 with corrupted frame indicator SIS1 coordinate error time=153213872.17072 x=0 y=0 pha[0]=0 chip=3 Dropping SF 3191 with inconsistent datamode 0/31 1.99999 second gap between superframes 3200 and 3201 Dropping SF 3353 with invalid bit rate 7 Dropping SF 3358 with inconsistent datamode 0/31 Dropping SF 3413 with inconsistent datamode 0/31 Dropping SF 3455 with invalid bit rate 7 Dropping SF 3534 with inconsistent datamode 0/31 Dropping SF 3614 with corrupted frame indicator Dropping SF 3624 with inconsistent datamode 0/31 Dropping SF 3651 with inconsistent datamode 0/31 Dropping SF 3698 with inconsistent datamode 0/31 Dropping SF 3719 with inconsistent datamode 0/31 Dropping SF 3730 with invalid bit rate 7 Dropping SF 3773 with inconsistent datamode 0/31 Dropping SF 3800 with corrupted frame indicator Dropping SF 3840 with inconsistent datamode 0/31 Dropping SF 3923 with corrupted frame indicator Dropping SF 3995 with inconsistent datamode 0/31 623.998 second gap between superframes 4061 and 4062 Dropping SF 4118 with inconsistent datamode 0/31 Dropping SF 4203 with corrupted frame indicator Dropping SF 4214 with inconsistent datamode 0/31 Dropping SF 4240 with inconsistent datamode 0/31 Dropping SF 4269 with inconsistent datamode 0/31 Dropping SF 4305 with inconsistent datamode 0/31 Dropping SF 4327 with corrupted frame indicator Dropping SF 4346 with inconsistent datamode 0/31 Dropping SF 4351 with inconsistent datamode 0/31 Dropping SF 4356 with inconsistent datamode 0/31 Dropping SF 4389 with inconsistent datamode 0/31 Dropping SF 4432 with inconsistent datamode 0/31 Dropping SF 4550 with corrupted frame indicator Dropping SF 4556 with inconsistent datamode 0/31 Dropping SF 4562 with corrupted frame indicator Dropping SF 4644 with invalid bit rate 7 Dropping SF 4700 with corrupted frame indicator Dropping SF 4740 with invalid bit rate 7 Dropping SF 4875 with inconsistent datamode 0/31 Dropping SF 4878 with inconsistent datamode 0/31 Dropping SF 4899 with inconsistent datamode 0/31 Dropping SF 4981 with inconsistent datamode 0/31 Dropping SF 5024 with corrupted frame indicator Dropping SF 5050 with inconsistent datamode 0/31 Dropping SF 5082 with inconsistent datamode 0/31 Dropping SF 5208 with inconsistent datamode 0/31 Dropping SF 5256 with inconsistent datamode 0/31 Dropping SF 5335 with invalid bit rate 7 Dropping SF 5364 with inconsistent datamode 0/31 Dropping SF 5532 with inconsistent datamode 0/31 Dropping SF 5743 with inconsistent datamode 0/31 Dropping SF 5924 with inconsistent datamode 0/31 Dropping SF 5938 with corrupted frame indicator 607.998 second gap between superframes 5975 and 5976 Dropping SF 6002 with invalid bit rate 7 Dropping SF 6093 with invalid bit rate 7 Dropping SF 6111 with invalid bit rate 7 Dropping SF 6255 with inconsistent datamode 0/31 Dropping SF 6372 with inconsistent datamode 0/31 Dropping SF 6417 with inconsistent datamode 0/31 Dropping SF 6485 with corrupted frame indicator Dropping SF 6549 with inconsistent datamode 0/31 Dropping SF 6578 with corrupted frame indicator Dropping SF 6602 with invalid bit rate 7 Dropping SF 6616 with inconsistent datamode 0/31 Dropping SF 6623 with inconsistent datamode 0/31 Dropping SF 6645 with inconsistent datamode 31/0 Dropping SF 6650 with invalid bit rate 7 Dropping SF 6673 with invalid bit rate 7 6615 of 6707 super frames processed-> Removing the following files with NEVENTS=0
ft971109_0351_1020G200470H.fits[0] ft971109_0351_1020G300470H.fits[0] ft971109_0351_1020G301470H.fits[0]-> Checking for empty GTI extensions
ft971109_0351_1020S000101M.fits[2] ft971109_0351_1020S000201L.fits[2] ft971109_0351_1020S000301H.fits[2] ft971109_0351_1020S000401M.fits[2] ft971109_0351_1020S000501H.fits[2] ft971109_0351_1020S000601M.fits[2] ft971109_0351_1020S000701H.fits[2] ft971109_0351_1020S000801M.fits[2] ft971109_0351_1020S000901H.fits[2]-> Merging GTIs from the following files:
ft971109_0351_1020S100101M.fits[2] ft971109_0351_1020S100201L.fits[2] ft971109_0351_1020S100301H.fits[2] ft971109_0351_1020S100401M.fits[2] ft971109_0351_1020S100501H.fits[2] ft971109_0351_1020S100601M.fits[2] ft971109_0351_1020S100701H.fits[2] ft971109_0351_1020S100801M.fits[2] ft971109_0351_1020S100901H.fits[2]-> Merging GTIs from the following files:
ft971109_0351_1020G200170M.fits[2] ft971109_0351_1020G200270L.fits[2] ft971109_0351_1020G200370L.fits[2] ft971109_0351_1020G200570H.fits[2] ft971109_0351_1020G200670H.fits[2] ft971109_0351_1020G200770H.fits[2] ft971109_0351_1020G200870M.fits[2] ft971109_0351_1020G200970M.fits[2] ft971109_0351_1020G201070H.fits[2] ft971109_0351_1020G201170M.fits[2] ft971109_0351_1020G201270M.fits[2] ft971109_0351_1020G201370H.fits[2] ft971109_0351_1020G201470H.fits[2] ft971109_0351_1020G201570H.fits[2] ft971109_0351_1020G201670H.fits[2] ft971109_0351_1020G201770M.fits[2] ft971109_0351_1020G201870M.fits[2] ft971109_0351_1020G201970H.fits[2]-> Merging GTIs from the following files:
ft971109_0351_1020G300170M.fits[2] ft971109_0351_1020G300270L.fits[2] ft971109_0351_1020G300370L.fits[2] ft971109_0351_1020G300570H.fits[2] ft971109_0351_1020G300670H.fits[2] ft971109_0351_1020G300770H.fits[2] ft971109_0351_1020G300870M.fits[2] ft971109_0351_1020G300970M.fits[2] ft971109_0351_1020G301070H.fits[2] ft971109_0351_1020G301170M.fits[2] ft971109_0351_1020G301270M.fits[2] ft971109_0351_1020G301370H.fits[2] ft971109_0351_1020G301570H.fits[2] ft971109_0351_1020G301670H.fits[2] ft971109_0351_1020G301770M.fits[2] ft971109_0351_1020G301870M.fits[2] ft971109_0351_1020G301970H.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 4 photon cnt = 10674 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 826 GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 60 GISSORTSPLIT:LO:g200170m.prelist merge count = 4 photon cnt = 5598 GISSORTSPLIT:LO:g200270m.prelist merge count = 3 photon cnt = 76 GISSORTSPLIT:LO:Total filenames split = 18 GISSORTSPLIT:LO:Total split file cnt = 9 GISSORTSPLIT:LO:End program-> Creating ad55015000g200170h.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G200770H.fits 2 -- ft971109_0351_1020G201070H.fits 3 -- ft971109_0351_1020G201670H.fits 4 -- ft971109_0351_1020G201970H.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G200770H.fits 2 -- ft971109_0351_1020G201070H.fits 3 -- ft971109_0351_1020G201670H.fits 4 -- ft971109_0351_1020G201970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55015000g200270m.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G200170M.fits 2 -- ft971109_0351_1020G200970M.fits 3 -- ft971109_0351_1020G201270M.fits 4 -- ft971109_0351_1020G201870M.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G200170M.fits 2 -- ft971109_0351_1020G200970M.fits 3 -- ft971109_0351_1020G201270M.fits 4 -- ft971109_0351_1020G201870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft971109_0351_1020G200370L.fits
---- cmerge: version 1.6 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G200370L.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G200370L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000076 events
ft971109_0351_1020G200870M.fits ft971109_0351_1020G201170M.fits ft971109_0351_1020G201770M.fits-> Ignoring the following files containing 000000060 events
ft971109_0351_1020G200270L.fits-> Ignoring the following files containing 000000005 events
ft971109_0351_1020G200670H.fits ft971109_0351_1020G201570H.fits-> Ignoring the following files containing 000000004 events
ft971109_0351_1020G201470H.fits-> Ignoring the following files containing 000000003 events
ft971109_0351_1020G200570H.fits-> Ignoring the following files containing 000000002 events
ft971109_0351_1020G201370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 4 photon cnt = 9965 GISSORTSPLIT:LO:g300270h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 755 GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 61 GISSORTSPLIT:LO:g300170m.prelist merge count = 4 photon cnt = 4930 GISSORTSPLIT:LO:g300270m.prelist merge count = 3 photon cnt = 56 GISSORTSPLIT:LO:Total filenames split = 17 GISSORTSPLIT:LO:Total split file cnt = 8 GISSORTSPLIT:LO:End program-> Creating ad55015000g300170h.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G300770H.fits 2 -- ft971109_0351_1020G301070H.fits 3 -- ft971109_0351_1020G301670H.fits 4 -- ft971109_0351_1020G301970H.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G300770H.fits 2 -- ft971109_0351_1020G301070H.fits 3 -- ft971109_0351_1020G301670H.fits 4 -- ft971109_0351_1020G301970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55015000g300270m.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G300170M.fits 2 -- ft971109_0351_1020G300970M.fits 3 -- ft971109_0351_1020G301270M.fits 4 -- ft971109_0351_1020G301870M.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G300170M.fits 2 -- ft971109_0351_1020G300970M.fits 3 -- ft971109_0351_1020G301270M.fits 4 -- ft971109_0351_1020G301870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft971109_0351_1020G300370L.fits
---- cmerge: version 1.6 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020G300370L.fits Merging binary extension #: 2 1 -- ft971109_0351_1020G300370L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000061 events
ft971109_0351_1020G300270L.fits-> Ignoring the following files containing 000000056 events
ft971109_0351_1020G300870M.fits ft971109_0351_1020G301170M.fits ft971109_0351_1020G301770M.fits-> Ignoring the following files containing 000000005 events
ft971109_0351_1020G300670H.fits ft971109_0351_1020G301570H.fits-> Ignoring the following files containing 000000003 events
ft971109_0351_1020G301370H.fits-> Ignoring the following files containing 000000002 events
ft971109_0351_1020G300570H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 4 photon cnt = 34823 SIS0SORTSPLIT:LO:s000201l.prelist merge count = 1 photon cnt = 1989 SIS0SORTSPLIT:LO:s000301m.prelist merge count = 4 photon cnt = 16723 SIS0SORTSPLIT:LO:Total filenames split = 9 SIS0SORTSPLIT:LO:Total split file cnt = 3 SIS0SORTSPLIT:LO:End program-> Creating ad55015000s000101h.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S000301H.fits 2 -- ft971109_0351_1020S000501H.fits 3 -- ft971109_0351_1020S000701H.fits 4 -- ft971109_0351_1020S000901H.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S000301H.fits 2 -- ft971109_0351_1020S000501H.fits 3 -- ft971109_0351_1020S000701H.fits 4 -- ft971109_0351_1020S000901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55015000s000201m.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S000101M.fits 2 -- ft971109_0351_1020S000401M.fits 3 -- ft971109_0351_1020S000601M.fits 4 -- ft971109_0351_1020S000801M.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S000101M.fits 2 -- ft971109_0351_1020S000401M.fits 3 -- ft971109_0351_1020S000601M.fits 4 -- ft971109_0351_1020S000801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft971109_0351_1020S000201L.fits
---- cmerge: version 1.6 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S000201L.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S000201L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 4 photon cnt = 57175 SIS1SORTSPLIT:LO:s100201l.prelist merge count = 1 photon cnt = 2560 SIS1SORTSPLIT:LO:s100301m.prelist merge count = 4 photon cnt = 28876 SIS1SORTSPLIT:LO:Total filenames split = 9 SIS1SORTSPLIT:LO:Total split file cnt = 3 SIS1SORTSPLIT:LO:End program-> Creating ad55015000s100101h.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S100301H.fits 2 -- ft971109_0351_1020S100501H.fits 3 -- ft971109_0351_1020S100701H.fits 4 -- ft971109_0351_1020S100901H.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S100301H.fits 2 -- ft971109_0351_1020S100501H.fits 3 -- ft971109_0351_1020S100701H.fits 4 -- ft971109_0351_1020S100901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55015000s100201m.unf
---- cmerge: version 1.6 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S100101M.fits 2 -- ft971109_0351_1020S100401M.fits 3 -- ft971109_0351_1020S100601M.fits 4 -- ft971109_0351_1020S100801M.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S100101M.fits 2 -- ft971109_0351_1020S100401M.fits 3 -- ft971109_0351_1020S100601M.fits 4 -- ft971109_0351_1020S100801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft971109_0351_1020S100201L.fits
---- cmerge: version 1.6 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971109_0351_1020S100201L.fits Merging binary extension #: 2 1 -- ft971109_0351_1020S100201L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Tar-ing together the leftover raw files
a ft971109_0351_1020G200270L.fits 31K a ft971109_0351_1020G200570H.fits 31K a ft971109_0351_1020G200670H.fits 31K a ft971109_0351_1020G200870M.fits 31K a ft971109_0351_1020G201170M.fits 31K a ft971109_0351_1020G201370H.fits 31K a ft971109_0351_1020G201470H.fits 31K a ft971109_0351_1020G201570H.fits 31K a ft971109_0351_1020G201770M.fits 31K a ft971109_0351_1020G300270L.fits 31K a ft971109_0351_1020G300570H.fits 31K a ft971109_0351_1020G300670H.fits 31K a ft971109_0351_1020G300870M.fits 31K a ft971109_0351_1020G301170M.fits 31K a ft971109_0351_1020G301370H.fits 31K a ft971109_0351_1020G301570H.fits 31K a ft971109_0351_1020G301770M.fits 31K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft971109_0351.1020' is successfully opened Data Start Time is 153201072.34 (19971109 035108) Time Margin 2.0 sec included Sync error detected in 3030 th SF 'ft971109_0351.1020' EOF detected, sf=6707 Data End Time is 153224454.26 (19971109 102050) Gain History is written in ft971109_0351_1020.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft971109_0351_1020.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft971109_0351_1020.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft971109_0351_1020CMHK.fits
The sum of the selected column is 18196.000 The mean of the selected column is 93.312821 The standard deviation of the selected column is 1.2557455 The minimum of selected column is 92.000000 The maximum of selected column is 97.000000 The number of points used in calculation is 195-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 18196.000 The mean of the selected column is 93.312821 The standard deviation of the selected column is 1.2557455 The minimum of selected column is 92.000000 The maximum of selected column is 97.000000 The number of points used in calculation is 195
ASCALIN_V0.9u(mod)-> Checking if ad55015000g200270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000g300170h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000g300270m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s000301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad55015000s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)
S0-HK file: ft971109_0351_1020S0HK.fits
S1-HK file: ft971109_0351_1020S1HK.fits
G2-HK file: ft971109_0351_1020G2HK.fits
G3-HK file: ft971109_0351_1020G3HK.fits
Date and time are: 1997-11-09 03:50:42 mjd=50761.160212
Orbit file name is ./frf.orbit.241
Epoch of Orbital Elements: 1997-11-03 21:59:59
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa971109_0351.1020
output FITS File: ft971109_0351_1020.mkf
mkfilter2: Warning, faQparam error: time= 1.532009943368e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 1.532010263368e+08 outside range of attitude file
Euler angles undefined for this bin
Total 734 Data bins were processed.
-> Checking if column TIME in ft971109_0351_1020.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 5063.8286 The mean of the selected column is 19.858151 The standard deviation of the selected column is 11.215920 The minimum of selected column is 3.2187605 The maximum of selected column is 83.406517 The number of points used in calculation is 255-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<53.5 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad55015000s000112h.unf into ad55015000s000112h.evt
The sum of the selected column is 5063.8286 The mean of the selected column is 19.858151 The standard deviation of the selected column is 11.215920 The minimum of selected column is 3.2187605 The maximum of selected column is 83.406517 The number of points used in calculation is 255-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<53.5 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad55015000s000201m.unf because of mode
The sum of the selected column is 1799.0057 The mean of the selected column is 23.363710 The standard deviation of the selected column is 16.652728 The minimum of selected column is 4.9375157 The maximum of selected column is 98.406563 The number of points used in calculation is 77-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<73.3 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad55015000s000212m.unf into ad55015000s000212m.evt
The sum of the selected column is 1799.0057 The mean of the selected column is 23.363710 The standard deviation of the selected column is 16.652728 The minimum of selected column is 4.9375157 The maximum of selected column is 98.406563 The number of points used in calculation is 77-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<73.3 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad55015000s000301l.unf because of mode
The sum of the selected column is 8171.2388 The mean of the selected column is 31.549185 The standard deviation of the selected column is 16.494075 The minimum of selected column is 8.2812767 The maximum of selected column is 127.09416 The number of points used in calculation is 259-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0 && S1_PIXL1<81 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad55015000s100112h.unf into ad55015000s100112h.evt
The sum of the selected column is 8171.2388 The mean of the selected column is 31.549185 The standard deviation of the selected column is 16.494075 The minimum of selected column is 8.2812767 The maximum of selected column is 127.09416 The number of points used in calculation is 259-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0 && S1_PIXL1<81 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad55015000s100201m.unf because of mode
The sum of the selected column is 1919.3811 The mean of the selected column is 29.528940 The standard deviation of the selected column is 11.616308 The minimum of selected column is 11.625037 The maximum of selected column is 64.500206 The number of points used in calculation is 65-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0 && S1_PIXL1<64.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad55015000s100212m.unf into ad55015000s100212m.evt
The sum of the selected column is 1919.3811 The mean of the selected column is 29.528940 The standard deviation of the selected column is 11.616308 The minimum of selected column is 11.625037 The maximum of selected column is 64.500206 The number of points used in calculation is 65-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0 && S1_PIXL1<64.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad55015000s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0) )&&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad55015000s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0) )&&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad55015000s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad55015000g200270m.unf into ad55015000g200270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad55015000g200370l.unf into ad55015000g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad55015000g300170h.unf into ad55015000g300170h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad55015000g300270m.unf into ad55015000g300270m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad55015000g300370l.unf into ad55015000g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55015000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9066
Mean RA/DEC/ROLL : 296.7798 25.2100 101.9066
Pnt RA/DEC/ROLL : 296.7752 25.1602 101.9066
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 83
Total GTI (secs) : 10129.944
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2169.99 2169.99
20 Percent Complete: Total/live time: 2169.99 2169.99
30 Percent Complete: Total/live time: 3450.02 3450.02
40 Percent Complete: Total/live time: 4616.51 4616.51
50 Percent Complete: Total/live time: 5192.05 5192.05
60 Percent Complete: Total/live time: 6352.01 6352.01
70 Percent Complete: Total/live time: 7538.45 7538.45
80 Percent Complete: Total/live time: 8214.01 8214.01
90 Percent Complete: Total/live time: 10063.87 10063.87
100 Percent Complete: Total/live time: 10129.94 10129.94
Number of attitude steps used: 31
Number of attitude steps avail: 21782
Mean RA/DEC pixel offset: -11.8475 -2.7319
writing expo file: ad55015000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g200170h.evt
ASCAEXPO_V0.9b
reading data file: ad55015000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9066
Mean RA/DEC/ROLL : 296.7775 25.2106 101.9066
Pnt RA/DEC/ROLL : 296.7592 25.1380 101.9066
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 3
Total GTI (secs) : 2768.064
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 480.00 480.00
20 Percent Complete: Total/live time: 780.00 780.00
30 Percent Complete: Total/live time: 2387.99 2387.99
40 Percent Complete: Total/live time: 2387.99 2387.99
50 Percent Complete: Total/live time: 2496.00 2496.00
60 Percent Complete: Total/live time: 2496.00 2496.00
70 Percent Complete: Total/live time: 2768.06 2768.06
100 Percent Complete: Total/live time: 2768.06 2768.06
Number of attitude steps used: 13
Number of attitude steps avail: 841
Mean RA/DEC pixel offset: -12.9019 -2.5969
writing expo file: ad55015000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g200270m.evt
ASCAEXPO_V0.9b
reading data file: ad55015000g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9068
Mean RA/DEC/ROLL : 296.7798 25.2105 101.9068
Pnt RA/DEC/ROLL : 296.7787 25.1598 101.9068
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 1
Total GTI (secs) : 223.984
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 223.98 223.98
100 Percent Complete: Total/live time: 223.98 223.98
Number of attitude steps used: 2
Number of attitude steps avail: 178
Mean RA/DEC pixel offset: -6.3754 -1.5906
writing expo file: ad55015000g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g200370l.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55015000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9079
Mean RA/DEC/ROLL : 296.7827 25.1853 101.9079
Pnt RA/DEC/ROLL : 296.7722 25.1849 101.9079
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 83
Total GTI (secs) : 10129.944
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2169.99 2169.99
20 Percent Complete: Total/live time: 2169.99 2169.99
30 Percent Complete: Total/live time: 3450.02 3450.02
40 Percent Complete: Total/live time: 4616.51 4616.51
50 Percent Complete: Total/live time: 5192.05 5192.05
60 Percent Complete: Total/live time: 6352.01 6352.01
70 Percent Complete: Total/live time: 7538.45 7538.45
80 Percent Complete: Total/live time: 8214.01 8214.01
90 Percent Complete: Total/live time: 10063.87 10063.87
100 Percent Complete: Total/live time: 10129.94 10129.94
Number of attitude steps used: 31
Number of attitude steps avail: 21782
Mean RA/DEC pixel offset: 0.2311 -1.5320
writing expo file: ad55015000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g300170h.evt
ASCAEXPO_V0.9b
reading data file: ad55015000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9079
Mean RA/DEC/ROLL : 296.7804 25.1859 101.9079
Pnt RA/DEC/ROLL : 296.7562 25.1627 101.9079
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 3
Total GTI (secs) : 2768.064
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 480.00 480.00
20 Percent Complete: Total/live time: 780.00 780.00
30 Percent Complete: Total/live time: 2387.99 2387.99
40 Percent Complete: Total/live time: 2387.99 2387.99
50 Percent Complete: Total/live time: 2496.00 2496.00
60 Percent Complete: Total/live time: 2496.00 2496.00
70 Percent Complete: Total/live time: 2768.06 2768.06
100 Percent Complete: Total/live time: 2768.06 2768.06
Number of attitude steps used: 13
Number of attitude steps avail: 841
Mean RA/DEC pixel offset: -1.7523 -1.4893
writing expo file: ad55015000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g300270m.evt
ASCAEXPO_V0.9b
reading data file: ad55015000g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9081
Mean RA/DEC/ROLL : 296.7828 25.1857 101.9081
Pnt RA/DEC/ROLL : 296.7758 25.1845 101.9081
Image rebin factor : 1
Attitude Records : 26451
GTI intervals : 1
Total GTI (secs) : 223.984
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 223.98 223.98
100 Percent Complete: Total/live time: 223.98 223.98
Number of attitude steps used: 2
Number of attitude steps avail: 178
Mean RA/DEC pixel offset: -0.3361 -0.9907
writing expo file: ad55015000g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000g300370l.evt
ASCAEXPO_V0.9b
reading data file: ad55015000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9143
Mean RA/DEC/ROLL : 296.7978 25.2007 101.9143
Pnt RA/DEC/ROLL : 296.7571 25.1695 101.9143
Image rebin factor : 4
Attitude Records : 26451
Hot Pixels : 10
GTI intervals : 51
Total GTI (secs) : 8287.612
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2534.47 2534.47
20 Percent Complete: Total/live time: 2534.47 2534.47
30 Percent Complete: Total/live time: 2658.47 2658.47
40 Percent Complete: Total/live time: 4931.46 4931.46
50 Percent Complete: Total/live time: 4931.46 4931.46
60 Percent Complete: Total/live time: 5300.00 5300.00
70 Percent Complete: Total/live time: 6075.94 6075.94
80 Percent Complete: Total/live time: 6796.00 6796.00
90 Percent Complete: Total/live time: 8223.74 8223.74
100 Percent Complete: Total/live time: 8287.61 8287.61
Number of attitude steps used: 14
Number of attitude steps avail: 21145
Mean RA/DEC pixel offset: -55.2997 -86.6078
writing expo file: ad55015000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000s000102h.evt
ASCAEXPO_V0.9b
reading data file: ad55015000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9143
Mean RA/DEC/ROLL : 296.7958 25.2012 101.9143
Pnt RA/DEC/ROLL : 296.7411 25.1472 101.9143
Image rebin factor : 4
Attitude Records : 26451
Hot Pixels : 7
GTI intervals : 11
Total GTI (secs) : 2456.189
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 416.00 416.00
20 Percent Complete: Total/live time: 716.00 716.00
30 Percent Complete: Total/live time: 2131.99 2131.99
40 Percent Complete: Total/live time: 2131.99 2131.99
50 Percent Complete: Total/live time: 2304.00 2304.00
60 Percent Complete: Total/live time: 2304.00 2304.00
70 Percent Complete: Total/live time: 2332.12 2332.12
80 Percent Complete: Total/live time: 2332.12 2332.12
90 Percent Complete: Total/live time: 2456.19 2456.19
100 Percent Complete: Total/live time: 2456.19 2456.19
Number of attitude steps used: 14
Number of attitude steps avail: 804
Mean RA/DEC pixel offset: -66.9113 -82.7065
writing expo file: ad55015000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000s000202m.evt
ASCAEXPO_V0.9b
reading data file: ad55015000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9069
Mean RA/DEC/ROLL : 296.7804 25.1984 101.9069
Pnt RA/DEC/ROLL : 296.7745 25.1718 101.9069
Image rebin factor : 4
Attitude Records : 26451
Hot Pixels : 22
GTI intervals : 53
Total GTI (secs) : 8231.803
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 2534.47 2534.47
20 Percent Complete: Total/live time: 2534.47 2534.47
30 Percent Complete: Total/live time: 2658.47 2658.47
40 Percent Complete: Total/live time: 4931.46 4931.46
50 Percent Complete: Total/live time: 4931.46 4931.46
60 Percent Complete: Total/live time: 5300.00 5300.00
70 Percent Complete: Total/live time: 6067.94 6067.94
80 Percent Complete: Total/live time: 6748.00 6748.00
90 Percent Complete: Total/live time: 8231.80 8231.80
100 Percent Complete: Total/live time: 8231.80 8231.80
Number of attitude steps used: 13
Number of attitude steps avail: 20911
Mean RA/DEC pixel offset: -59.4055 -14.5481
writing expo file: ad55015000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000s100102h.evt
ASCAEXPO_V0.9b
reading data file: ad55015000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa971109_0351.1020
making an exposure map...
Aspect RA/DEC/ROLL : 296.7790 25.1835 101.9069
Mean RA/DEC/ROLL : 296.7784 25.1989 101.9069
Pnt RA/DEC/ROLL : 296.7585 25.1496 101.9069
Image rebin factor : 4
Attitude Records : 26451
Hot Pixels : 20
GTI intervals : 13
Total GTI (secs) : 2112.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 280.00 280.00
20 Percent Complete: Total/live time: 480.00 480.00
30 Percent Complete: Total/live time: 780.00 780.00
40 Percent Complete: Total/live time: 1939.99 1939.99
50 Percent Complete: Total/live time: 1939.99 1939.99
60 Percent Complete: Total/live time: 2016.00 2016.00
70 Percent Complete: Total/live time: 2016.00 2016.00
80 Percent Complete: Total/live time: 2019.94 2019.94
90 Percent Complete: Total/live time: 2019.94 2019.94
100 Percent Complete: Total/live time: 2112.00 2112.00
Number of attitude steps used: 14
Number of attitude steps avail: 804
Mean RA/DEC pixel offset: -71.0381 -15.9876
writing expo file: ad55015000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55015000s100202m.evtad55015000s000102h.expo ad55015000s000202m.expo ad55015000s100102h.expo ad55015000s100202m.expo-> Summing the following images to produce ad55015000sis32002_all.totsky
ad55015000s000102h.img ad55015000s000202m.img ad55015000s100102h.img ad55015000s100202m.img-> Summing the following images to produce ad55015000sis32002_lo.totsky
ad55015000s000102h_lo.img ad55015000s000202m_lo.img ad55015000s100102h_lo.img ad55015000s100202m_lo.img-> Summing the following images to produce ad55015000sis32002_hi.totsky
ad55015000s000102h_hi.img ad55015000s000202m_hi.img ad55015000s100102h_hi.img ad55015000s100202m_hi.img-> Running XIMAGE to create ad55015000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55015000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 2.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 2 min: 0 ![2]XIMAGE> read/exp_map ad55015000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 179.063 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 179 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "RIDGE_EDGE_N6" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 November 9, 1997 Exposure: 21087.6 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 10544 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 18.0000 18 0 ![11]XIMAGE> exit-> Summing gis images
ad55015000g200170h.expo ad55015000g200270m.expo ad55015000g200370l.expo ad55015000g300170h.expo ad55015000g300270m.expo ad55015000g300370l.expo-> Summing the following images to produce ad55015000gis25670_all.totsky
ad55015000g200170h.img ad55015000g200270m.img ad55015000g200370l.img ad55015000g300170h.img ad55015000g300270m.img ad55015000g300370l.img-> Summing the following images to produce ad55015000gis25670_lo.totsky
ad55015000g200170h_lo.img ad55015000g200270m_lo.img ad55015000g200370l_lo.img ad55015000g300170h_lo.img ad55015000g300270m_lo.img ad55015000g300370l_lo.img-> Summing the following images to produce ad55015000gis25670_hi.totsky
ad55015000g200170h_hi.img ad55015000g200270m_hi.img ad55015000g200370l_hi.img ad55015000g300170h_hi.img ad55015000g300270m_hi.img ad55015000g300370l_hi.img-> Running XIMAGE to create ad55015000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55015000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 6.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 6 min: 0 ![2]XIMAGE> read/exp_map ad55015000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 437.400 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 437 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "RIDGE_EDGE_N6" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 November 9, 1997 Exposure: 26243.9 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 820.000 820 0 ![11]XIMAGE> exit
144 137 7.15422e-05 108 16 6.09246-> Smoothing ad55015000gis25670_hi.totsky with ad55015000gis25670.totexpo
147 138 4.51027e-05 111 18 6.73916-> Smoothing ad55015000gis25670_lo.totsky with ad55015000gis25670.totexpo
144 134 2.39914e-05 106 16 4.76062-> Determining extraction radii
144 137 24 T-> Sources with radius >= 2
144 137 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55015000gis25670.src
151 187 5.6447e-06 185 32 4.02881-> Determining extraction radii
151 187 38 T-> Sources with radius >= 2
151 187 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55015000sis32002.src
The sum of the selected column is 15356.000 The mean of the selected column is 511.86667 The standard deviation of the selected column is 17.612169 The minimum of selected column is 483.00000 The maximum of selected column is 541.00000 The number of points used in calculation is 30-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 16138.000 The mean of the selected column is 537.93333 The standard deviation of the selected column is 21.278017 The minimum of selected column is 503.00000 The maximum of selected column is 574.00000 The number of points used in calculation is 30-> Converting (604.0,748.0,2.0) to s1 detector coordinates
The sum of the selected column is 1010.0000 The mean of the selected column is 112.22222 The standard deviation of the selected column is 0.66666667 The minimum of selected column is 111.00000 The maximum of selected column is 113.00000 The number of points used in calculation is 9-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1268.0000 The mean of the selected column is 140.88889 The standard deviation of the selected column is 0.92796073 The minimum of selected column is 139.00000 The maximum of selected column is 142.00000 The number of points used in calculation is 9-> Converting (144.0,137.0,2.0) to g3 detector coordinates
The sum of the selected column is 1174.0000 The mean of the selected column is 117.40000 The standard deviation of the selected column is 1.0749677 The minimum of selected column is 116.00000 The maximum of selected column is 119.00000 The number of points used in calculation is 10-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1412.0000 The mean of the selected column is 141.20000 The standard deviation of the selected column is 1.4757296 The minimum of selected column is 139.00000 The maximum of selected column is 143.00000 The number of points used in calculation is 10-> Removing empty region file ad55015000s132002_0.reg
1 ad55015000s000102h.evt 633 1 ad55015000s000202m.evt 633-> Fetching SIS0_NOTCHIP0.1
ad55015000s000102h.evt ad55015000s000202m.evt-> Deleting ad55015000s010102_1.pi since it has 242 events
1 ad55015000s000112h.evt 693 1 ad55015000s000212m.evt 693-> SIS0_NOTCHIP0.1 already present in current directory
ad55015000s000112h.evt ad55015000s000212m.evt-> Deleting ad55015000s010212_1.pi since it has 261 events
1 ad55015000s100102h.evt 628 1 ad55015000s100202m.evt 628-> Fetching SIS1_NOTCHIP0.1
1 ad55015000s100112h.evt 667 1 ad55015000s100212m.evt 667-> SIS1_NOTCHIP0.1 already present in current directory
1 ad55015000g200170h.evt 4085 1 ad55015000g200270m.evt 4085 1 ad55015000g200370l.evt 4085-> GIS2_REGION256.4 already present in current directory
ad55015000g200170h.evt ad55015000g200270m.evt ad55015000g200370l.evt-> Correcting ad55015000g210170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad55015000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 13122. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 83 are grouped by a factor 84 ... 84 - 105 are grouped by a factor 22 ... 106 - 122 are grouped by a factor 17 ... 123 - 145 are grouped by a factor 23 ... 146 - 163 are grouped by a factor 18 ... 164 - 182 are grouped by a factor 19 ... 183 - 210 are grouped by a factor 28 ... 211 - 257 are grouped by a factor 47 ... 258 - 302 are grouped by a factor 45 ... 303 - 366 are grouped by a factor 64 ... 367 - 442 are grouped by a factor 76 ... 443 - 565 are grouped by a factor 123 ... 566 - 800 are grouped by a factor 235 ... 801 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55015000g210170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 48 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 49 78
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.46000E+02
Weighted mean angle from optical axis = 6.031 arcmin
-> Standard Output From STOOL group_event_files:1 ad55015000g300170h.evt 4447 1 ad55015000g300270m.evt 4447 1 ad55015000g300370l.evt 4447-> GIS3_REGION256.4 already present in current directory
ad55015000g300170h.evt ad55015000g300270m.evt ad55015000g300370l.evt-> Correcting ad55015000g310170_1.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad55015000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 13122. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 73 are grouped by a factor 74 ... 74 - 96 are grouped by a factor 23 ... 97 - 115 are grouped by a factor 19 ... 116 - 132 are grouped by a factor 17 ... 133 - 150 are grouped by a factor 18 ... 151 - 176 are grouped by a factor 13 ... 177 - 193 are grouped by a factor 17 ... 194 - 219 are grouped by a factor 26 ... 220 - 242 are grouped by a factor 23 ... 243 - 272 are grouped by a factor 30 ... 273 - 311 are grouped by a factor 39 ... 312 - 340 are grouped by a factor 29 ... 341 - 384 are grouped by a factor 44 ... 385 - 448 are grouped by a factor 64 ... 449 - 519 are grouped by a factor 71 ... 520 - 677 are grouped by a factor 158 ... 678 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55015000g310170_1.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 48 by 48 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 54 78
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.30000E+02
Weighted mean angle from optical axis = 3.707 arcmin
-> Plotting ad55015000g210170_1_pi.ps from ad55015000g210170_1.pi
XSPEC 9.01 10:52:29 29-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55015000g210170_1.pi
Net count rate (cts/s) for file 1 4.1838E-02+/- 2.0940E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55015000g310170_1_pi.ps from ad55015000g310170_1.pi
XSPEC 9.01 10:52:41 29-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55015000g310170_1.pi
Net count rate (cts/s) for file 1 5.5937E-02+/- 2.4694E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55015000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ RIDGE_EDGE_N6 Start Time (d) .... 10761 03:53:22.337
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10761 10:20:50.337
No. of Rows ....... 10 Bin Time (s) ...... 1195.
Right Ascension ... 2.9678E+02 Internal time sys.. Converted to TJD
Declination ....... 2.5183E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 20 Newbins of 1195.08 (s)
Intv 1 Start10761 4: 3:19
Ser.1 Avg 0.4073E-01 Chisq 3.235 Var 0.1235E-04 Newbs. 10
Min 0.3537E-01 Max 0.4533E-01expVar 0.3819E-04 Bins 10
Results from Statistical Analysis
Newbin Integration Time (s).. 1195.1
Interval Duration (s)........ 21511.
No. of Newbins .............. 10
Average (c/s) ............... 0.40730E-01 +/- 0.21E-02
Standard Deviation (c/s)..... 0.35149E-02
Minimum (c/s)................ 0.35370E-01
Maximum (c/s)................ 0.45332E-01
Variance ((c/s)**2).......... 0.12355E-04 +/- 0.58E-05
Expected Variance ((c/s)**2). 0.38188E-04 +/- 0.18E-04
Third Moment ((c/s)**3)......-0.56343E-08
Average Deviation (c/s)...... 0.31354E-02
Skewness.....................-0.12974 +/- 0.77
Kurtosis..................... -1.4544 +/- 1.5
RMS fractional variation....< 0.24880 (3 sigma)
Chi-Square................... 3.2352 dof 9
Chi-Square Prob of constancy. 0.95423 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.67394 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 20 Newbins of 1195.08 (s)
Intv 1 Start10761 4: 3:19
Ser.1 Avg 0.4073E-01 Chisq 3.235 Var 0.1235E-04 Newbs. 10
Min 0.3537E-01 Max 0.4533E-01expVar 0.3819E-04 Bins 10
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad55015000g200070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad55015000g300170h.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55015000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ RIDGE_EDGE_N6 Start Time (d) .... 10761 03:53:22.337
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10761 10:20:50.337
No. of Rows ....... 16 Bin Time (s) ...... 893.9
Right Ascension ... 2.9678E+02 Internal time sys.. Converted to TJD
Declination ....... 2.5183E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 27 Newbins of 893.869 (s)
Intv 1 Start10761 4: 0:49
Ser.1 Avg 0.5594E-01 Chisq 15.29 Var 0.7426E-04 Newbs. 16
Min 0.4105E-01 Max 0.7057E-01expVar 0.7770E-04 Bins 16
Results from Statistical Analysis
Newbin Integration Time (s).. 893.87
Interval Duration (s)........ 22347.
No. of Newbins .............. 16
Average (c/s) ............... 0.55940E-01 +/- 0.23E-02
Standard Deviation (c/s)..... 0.86172E-02
Minimum (c/s)................ 0.41046E-01
Maximum (c/s)................ 0.70567E-01
Variance ((c/s)**2).......... 0.74257E-04 +/- 0.27E-04
Expected Variance ((c/s)**2). 0.77705E-04 +/- 0.28E-04
Third Moment ((c/s)**3)......-0.55310E-07
Average Deviation (c/s)...... 0.70213E-02
Skewness.....................-0.86437E-01 +/- 0.61
Kurtosis.....................-0.80324 +/- 1.2
RMS fractional variation....< 0.19285 (3 sigma)
Chi-Square................... 15.290 dof 15
Chi-Square Prob of constancy. 0.43064 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.57957E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 27 Newbins of 893.869 (s)
Intv 1 Start10761 4: 0:49
Ser.1 Avg 0.5594E-01 Chisq 15.29 Var 0.7426E-04 Newbs. 16
Min 0.4105E-01 Max 0.7057E-01expVar 0.7770E-04 Bins 16
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad55015000g300070_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad55015000g200170h.evt[2] ad55015000g200270m.evt[2] ad55015000g200370l.evt[2]-> Making L1 light curve of ft971109_0351_1020G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 19056 output records from 19139 good input G2_L1 records.-> Making L1 light curve of ft971109_0351_1020G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 11251 output records from 21629 good input G2_L1 records.-> Merging GTIs from the following files:
ad55015000g300170h.evt[2] ad55015000g300270m.evt[2] ad55015000g300370l.evt[2]-> Making L1 light curve of ft971109_0351_1020G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 18278 output records from 18361 good input G3_L1 records.-> Making L1 light curve of ft971109_0351_1020G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 11112 output records from 20818 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 6707 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft971109_0351_1020.mkf
1 ad55015000g200170h.unf 17098 1 ad55015000g200270m.unf 17098 1 ad55015000g200370l.unf 17098-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 11:03:48 29-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55015000g220170.cal
Net count rate (cts/s) for file 1 0.1525 +/- 2.7427E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.7752E+05 using 84 PHA bins.
Reduced chi-squared = 1.1396E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.7313E+05 using 84 PHA bins.
Reduced chi-squared = 1.1194E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.7313E+05 using 84 PHA bins.
Reduced chi-squared = 1.1052E+04
!XSPEC> renorm
Chi-Squared = 728.2 using 84 PHA bins.
Reduced chi-squared = 9.218
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
570.05 0 1.000 5.895 0.1108 4.4891E-02
4.0542E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
272.32 0 1.000 5.873 0.1659 6.2206E-02
3.6180E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
148.10 -1 1.000 5.920 0.1969 8.5351E-02
2.5480E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
132.62 -2 1.000 5.972 0.2206 9.8157E-02
1.5724E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
130.55 -3 1.000 5.951 0.2041 9.4268E-02
1.9504E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
130.26 -4 1.000 5.959 0.2092 9.5897E-02
1.7845E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
130.18 -5 1.000 5.955 0.2064 9.5178E-02
1.8557E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
130.17 -6 1.000 5.957 0.2074 9.5481E-02
1.8253E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95699 +/- 0.12524E-01
3 3 2 gaussian/b Sigma 0.207430 +/- 0.12172E-01
4 4 2 gaussian/b norm 9.548084E-02 +/- 0.30677E-02
5 2 3 gaussian/b LineE 6.55867 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.217654 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.825336E-02 +/- 0.23447E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 130.2 using 84 PHA bins.
Reduced chi-squared = 1.648
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55015000g220170.cal peaks at 5.95699 +/- 0.012524 keV1 ad55015000g300170h.unf 15650 1 ad55015000g300270m.unf 15650 1 ad55015000g300370l.unf 15650-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 11:04:27 29-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55015000g320170.cal
Net count rate (cts/s) for file 1 0.1285 +/- 2.5291E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1858E+06 using 84 PHA bins.
Reduced chi-squared = 1.5400E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1762E+06 using 84 PHA bins.
Reduced chi-squared = 1.5079E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1762E+06 using 84 PHA bins.
Reduced chi-squared = 1.4889E+04
!XSPEC> renorm
Chi-Squared = 899.5 using 84 PHA bins.
Reduced chi-squared = 11.39
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
749.36 0 1.000 5.893 6.6785E-02 3.5951E-02
3.0530E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
296.42 0 1.000 5.865 0.1111 5.8094E-02
2.5789E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
130.01 -1 1.000 5.899 0.1385 8.2356E-02
1.7525E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
115.74 -2 1.000 5.925 0.1507 9.0100E-02
1.2851E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
115.52 -3 1.000 5.923 0.1469 8.9832E-02
1.3144E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
115.51 -4 1.000 5.923 0.1467 8.9850E-02
1.3129E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
115.50 -5 1.000 5.923 0.1466 8.9845E-02
1.3135E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92281 +/- 0.87218E-02
3 3 2 gaussian/b Sigma 0.146582 +/- 0.11176E-01
4 4 2 gaussian/b norm 8.984455E-02 +/- 0.24646E-02
5 2 3 gaussian/b LineE 6.52104 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.153807 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.313507E-02 +/- 0.14777E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 115.5 using 84 PHA bins.
Reduced chi-squared = 1.462
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55015000g320170.cal peaks at 5.92281 +/- 0.0087218 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1787
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 1579
Flickering pixels iter, pixels & cnts : 1 2 8
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1787
Number of image cts rejected (N, %) : 158788.81
By chip : 0 1 2 3
Pixels rejected : 0 8 0 0
Image counts : 0 1787 0 0
Image cts rejected: 0 1587 0 0
Image cts rej (%) : 0.00 88.81 0.00 0.00
filtering data...
Total counts : 0 1787 0 0
Total cts rejected: 0 1587 0 0
Total cts rej (%) : 0.00 88.81 0.00 0.00
Number of clean counts accepted : 200
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1833
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 1579
Flickering pixels iter, pixels & cnts : 1 2 8
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 8
Number of (internal) image counts : 1833
Number of image cts rejected (N, %) : 158786.58
By chip : 0 1 2 3
Pixels rejected : 0 8 0 0
Image counts : 0 1833 0 0
Image cts rejected: 0 1587 0 0
Image cts rej (%) : 0.00 86.58 0.00 0.00
filtering data...
Total counts : 0 1833 0 0
Total cts rejected: 0 1587 0 0
Total cts rej (%) : 0.00 86.58 0.00 0.00
Number of clean counts accepted : 246
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 8
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6282
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 13 5999
Flickering pixels iter, pixels & cnts : 1 8 47
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 21
Number of (internal) image counts : 6282
Number of image cts rejected (N, %) : 604696.24
By chip : 0 1 2 3
Pixels rejected : 0 21 0 0
Image counts : 0 6282 0 0
Image cts rejected: 0 6046 0 0
Image cts rej (%) : 0.00 96.24 0.00 0.00
filtering data...
Total counts : 0 6282 0 0
Total cts rejected: 0 6046 0 0
Total cts rej (%) : 0.00 96.24 0.00 0.00
Number of clean counts accepted : 236
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6316
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 13 6001
Flickering pixels iter, pixels & cnts : 1 8 47
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 21
Number of (internal) image counts : 6316
Number of image cts rejected (N, %) : 604895.76
By chip : 0 1 2 3
Pixels rejected : 0 21 0 0
Image counts : 0 6316 0 0
Image cts rejected: 0 6048 0 0
Image cts rej (%) : 0.00 95.76 0.00 0.00
filtering data...
Total counts : 0 6316 0 0
Total cts rejected: 0 6048 0 0
Total cts rej (%) : 0.00 95.76 0.00 0.00
Number of clean counts accepted : 268
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1323
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 1276
Flickering pixels iter, pixels & cnts : 1 4 30
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 1323
Number of image cts rejected (N, %) : 130698.72
By chip : 0 1 2 3
Pixels rejected : 0 14 0 0
Image counts : 0 1323 0 0
Image cts rejected: 0 1306 0 0
Image cts rej (%) : 0.00 98.72 0.00 0.00
filtering data...
Total counts : 0 1323 0 0
Total cts rejected: 0 1306 0 0
Total cts rej (%) : 0.00 98.72 0.00 0.00
Number of clean counts accepted : 17
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55015000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1324
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 10 1276
Flickering pixels iter, pixels & cnts : 1 4 30
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 1324
Number of image cts rejected (N, %) : 130698.64
By chip : 0 1 2 3
Pixels rejected : 0 14 0 0
Image counts : 0 1324 0 0
Image cts rejected: 0 1306 0 0
Image cts rej (%) : 0.00 98.64 0.00 0.00
filtering data...
Total counts : 0 1324 0 0
Total cts rejected: 0 1306 0 0
Total cts rej (%) : 0.00 98.64 0.00 0.00
Number of clean counts accepted : 18
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55015000g200170h.unfOffset of 213408004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-10-07 00:00:00.00000 Modified Julian Day = 51458.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
216 704 2135 626 4062 640 5976 624 3
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files