Processing Job Log for Sequence 63007000, version 004

This is the complete and detailed record of how this sequence was processed.

The following information is also available:

Processing started ( 19:29:52 )

Fetching and uncompressing telemetry, attitude and orbit files ( 19:29:57 )

-> Fetching ft950729_2235.0800.Z
-> Uncompressing ft950729_2235.0800.Z
-> Checking if column TIME in ft950729_2235.0800 is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Fetching fa950729_2235.0800.Z
-> Uncompressing fa950729_2235.0800.Z
-> Fetching the latest orbit file
-> Fetching frf.orbit.213

Determine nominal aspect point for the observation ( 19:39:24 )

-> Running attitude FTOOL on merged attitude file
-> Standard Output From FTOOL attitude:
ATTITUDE_V0.9j
 
   reading attitude file:./merged.tmp
   open asc  output file:out.tmp
 
 AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
 
 Attitude file start and stop ascatime :  81210904.548900  81417643.887800
 Data     file start and stop ascatime :  81210904.548900  81417643.887800
 Aspecting run start and stop ascatime :  81210904.548982  81417643.887685
 
 
 Time interval averaged over (seconds) :    206739.338703
 Total pointing and manuver time (sec) :    123678.453125     83061.460938
 
 Mean boresight Euler angles :     10.535218      48.896607      36.726433
 
                                    RA             DEC         SUN ANGLE
 
 Mean solar position   (deg) :    128.91          18.64
 Mean aberration    (arcsec) :     10.60          -8.34
 
 Mean sat X-axis       (deg) :     59.150401     -37.153306      86.09
 Mean sat Y-axis       (deg) :    126.663058      26.782432       8.40
 Mean sat Z-axis       (deg) :     10.535218      41.103392      97.42
 
                      RA            DEC            ROLL          OFFSET
                    (deg)          (deg)          (deg)         (arcmin)
 
 Average            10.698294      41.359833     306.620270       0.158671
 Minimum            10.451193      41.354931     306.600647       0.000000
 Maximum            10.704482      41.613033     306.997650      56.157597
 Sigma (RMS)         0.000400       0.000277       0.007643       0.173841
 
 Number of ASPECT records processed =     148285
 
 Aspecting to RA/DEC                   :      10.69829369      41.35983276
    closing output   file...
    closing attitude file...
-> Standard Error Output From FTOOL attitude
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    81261383.885720
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    81330293.665119
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    81347584.110340
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    81349936.102813
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    81410691.409725
ATTITUDE_V0.9j : Detected gap > 15min in attitude file:
-> Standard Output From STOOL checkatt:
  
 Opening file: ./out.tmp                                                       
  
  ***************** Observation Info ******************
  
  RA (J2000 deg):   10.698 DEC:   41.360
  
  START TIME: SC  81210904.5490 = UT 29/07/95 22:35:04      
  
  ****** Definition of Attitude SENSOR Bit Flags ******
  
 Sensors used in the attitude determination and attitude control mode  
                                 1: USED,   0: NOT USED                
  
 B0:STT-A, B1:STT-B, B2:NSAS,  B3:GAS,    B4:SSAS-SA, B5:SSAS-SB,      
 B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,                  
 B11: Attitude control mode    1: coarse, 0: fine                      
 B12: Sun presence             1: day,    0: night                     
 B13: STT-A earth occultation  1: earth occultation, 0: no occultation 
 B14: STT-B earth occultation  1: earth occultation, 0: no occultation 
 B16,17,18: STT-A track stars no.1,2,3,     1: USED, 0: NOT USED       
 B19,20,21: STT-B track stars no.1,2,3,     1: USED, 0: NOT USED       
 B22,23: always 0                                                      
  
  ******** Attitude File Reconstruction Summary *******
  
                                    S S N G S S I I I I I A S S S S S
                                    T T S A S S R R R R R C U T T T T
                                    T T A S A A U U U U U M N T T T T
                                    - - S . A A - - - - - . . - - - -
                                    A B . . - - X Y Z S S . . A B A B
                                    . . . . S S . . . 1 2 . . O O S S
     offset_time separation sensor  . . . . A B . . . . . . . C C T T
        (sec)     (arcmin)          . . . . . . . . . . . . . C C R R
  
                             BIT:   0 1 2 3 4 5 6 7 8 9 A B C D E
  
       4.000060      0.182   2603   1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
    1755.994263      0.189   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
    3947.987061      0.254   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
    7515.975098      0.335   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
    9691.968750      0.203 F820C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
   13211.957031      0.246 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
   15435.949219      0.248   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   18971.937500      0.234 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
   21659.929688      0.194   2603   1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
   24715.919922      0.138   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
   26929.912109      0.140   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   30491.900391      0.069 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
   32675.894531      0.072   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   36507.882812      0.029 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
   38421.875000      0.045   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   41947.863281      0.088 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
   44171.855469      0.105   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   47707.843750      0.173 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
   49915.839844      0.199 F820C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
   54100.824219      0.251   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
   55663.820312      0.201   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   59227.808594      0.246 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
   61419.800781      0.307   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   64987.789062      0.332 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
   67155.781250      0.302   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   70683.773438      0.298 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
   72903.765625      0.258   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   76443.757812      0.220   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
   78649.750000      0.134   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   82203.734375      0.075   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
   84395.726562      0.031   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   87963.718750      0.056   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
   90143.710938      0.118   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   93723.695312      0.156 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
   95889.695312      0.180   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
   99419.679688      0.226 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
  101635.671875      0.191   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  105163.664062      0.282   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  107873.656250      0.156   2603   1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
  110923.640625      0.110   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  113129.632812      0.130   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  116667.625000      0.064 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
  118877.617188      0.085   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  122411.609375      0.100   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  124623.601562      0.131   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  128155.585938      0.156 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
  130369.578125      0.171   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  133915.562500      0.201 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
  136123.562500      0.224 F820C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
  140514.546875      0.265   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  141863.546875      0.147   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  145435.531250      0.175 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
  147611.531250      0.150 F820C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
  151195.515625      0.158 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
  153357.515625      0.127   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  156891.500000      0.126   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  159103.484375      0.123   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  162651.484375      0.113   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  164849.468750      0.097   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  168411.468750      0.123   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  170603.453125      0.117   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  174171.437500      0.146   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  176343.437500      0.177   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  179931.421875      0.176   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  182089.421875      0.177   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  185627.406250      0.178 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
  187837.406250      0.120   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  191387.390625      0.151 F828C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
  194079.375000      0.043   2603   1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
  197131.375000      0.027   2803   1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
  199329.359375      0.022   2003   1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
  202875.343750      0.033 FC28C3   1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 4 7
  205083.343750      0.021 FC20C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 7
  206731.343750     18.819   3603   1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
  206739.343750     56.157   3E03   1 1 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0
  
  Attitude  Records:   148285
  Attitude    Steps:   75
  
  Maneuver ACM time:     83061.5 sec
  Pointed  ACM time:     123679. sec
-> Calculating aspect point
-> Output from aspect:
28 22 count=1 sum1=9.822 sum2=48.127 sum3=37.107
75 74 count=1 sum1=10.288 sum2=48.644 sum3=36.79
99 99 count=87922 sum1=926027 sum2=4.29897e+06 sum3=3.22962e+06
99 100 count=1380 sum1=14537.1 sum2=67480.9 sum3=50680.2
100 99 count=44335 sum1=467178 sum2=2.16786e+06 sum3=1.62802e+06
100 100 count=14645 sum1=154325 sum2=716132 sum3=537748
0 out of 148284 points outside bin structure
-> Euler angles: 10.5344, 48.8963, 36.7278
-> RA=10.6975 Dec=41.3601 Roll=306.620
-> Galactic coordinates Lii=121.188196 Bii=-21.482368
-> Running fixatt on fa950729_2235.0800
-> Standard Output From STOOL fixatt:
Interpolating 32 records in time interval 8.14176e+07 - 8.14176e+07
Interpolating 61 records in time interval 8.14176e+07 - 8.14176e+07

Running frfread on telemetry files ( 19:50:45 )

-> Running frfread3.032 on the following telemetry files:
frf_directory,s,h,"./",,,"frf directory"
frf_file,s,h,"ft950729_2235.0800",,,"frf telemetry file"
-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32
ASCA format
Telemetry file: ft950729_2235.0800
Initial mode = 2  (Bright)
Initial value for dummy = 0
Initial datamode = 0  (Observation)
Initial sis = 0
Initial bit_rate = 2
Reading all superframes
reading PH mode
reading PCAL mode
reading MPCmode
Warning: unusual ccdlist pattern: 2 2 2 1 for S1 in superframe 5690
Warning: unusual ccdlist pattern: 2 2 2 1 for S1 in superframe 5690
Warning: unusual ccdlist pattern: 2 2 2 1 for S1 in superframe 5690
No mode = 0
Faint = 2057272
Bright = 318728
Fast = 0
Frame = 0
Dark frame = 0
Histogram = 0
Integration = 0
PH = 2373952
MPC = 0
PCAL = 0
Memory Check = 2048
Number of superframes = 37587
no. of SIS events found = 3371266
-> Standard Error Output From FTOOL frfread
coordinate error 0 0
coordinate error 0 0
coordinate error 0 6
coordinate error 0 6
coordinate error 0 384
coordinate error 0 384
coordinate error 0 0
coordinate error 0 192
coordinate error 0 192
coordinate error 0 3
coordinate error 0 96
coordinate error 0 1
coordinate error 0 0
coordinate error 0 6
coordinate error 0 0
coordinate error 0 0
coordinate error 0 384
coordinate error 0 0
coordinate error 3 0
coordinate error 0 0
coordinate error 0 0
coordinate error 24 0
coordinate error 0 96
coordinate error 0 96
coordinate error 48 0
coordinate error 0 384
coordinate error 0 6
coordinate error 0 0
coordinate error 192 0
coordinate error 96 0
coordinate error 0 0
coordinate error 0 24
coordinate error 1 256
coordinate error 0 48
coordinate error 3 0
coordinate error 0 48
coordinate error 0 12
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 12 0
coordinate error 256 0
coordinate error 0 12
coordinate error 0 384
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 6 0
coordinate error 12 0
coordinate error 0 96
coordinate error 0 0
coordinate error 0 0
coordinate error 96 0
coordinate error 0 192
coordinate error 0 0
coordinate error 384 0
coordinate error 0 0
coordinate error 0 0
coordinate error 256 0
coordinate error 192 0
coordinate error 384 482
coordinate error 0 384
coordinate error 0 24
coordinate error 0 0
coordinate error 0 12
coordinate error 119 493
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 48
coordinate error 0 12
coordinate error 384 0
coordinate error 0 6
coordinate error 48 0
coordinate error 0 0
coordinate error 256 0
coordinate error 0 0
coordinate error 48 0
coordinate error 96 0
coordinate error 0 0
coordinate error 6 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 12
coordinate error 0 0
coordinate error 0 0
coordinate error 384 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 111 499
coordinate error 0 0
coordinate error 4 5
coordinate error 24 0
coordinate error 0 0
coordinate error 0 384
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 192 0
-> Removing the following files with NEVENTS=0
ft950729_2235_0800G201170L.fits
ft950729_2235_0800G201870M.fits
ft950729_2235_0800G207970M.fits
ft950729_2235_0800G208070L.fits
ft950729_2235_0800G208670M.fits
ft950729_2235_0800G208770L.fits
ft950729_2235_0800G209070H.fits
ft950729_2235_0800G209599.fits
ft950729_2235_0800G209899.fits
ft950729_2235_0800G210170H.fits
ft950729_2235_0800G210270H.fits
ft950729_2235_0800G210370H.fits
ft950729_2235_0800G210470H.fits
ft950729_2235_0800G211170L.fits
ft950729_2235_0800G211270M.fits
ft950729_2235_0800G212070L.fits
ft950729_2235_0800G212170M.fits
ft950729_2235_0800G212270M.fits
ft950729_2235_0800G212370M.fits
ft950729_2235_0800G212470M.fits
ft950729_2235_0800G213370L.fits
ft950729_2235_0800G213470M.fits
ft950729_2235_0800G213570M.fits
ft950729_2235_0800G213670M.fits
ft950729_2235_0800G213770M.fits
ft950729_2235_0800G214570L.fits
ft950729_2235_0800G214670M.fits
ft950729_2235_0800G215370H.fits
ft950729_2235_0800G215470H.fits
ft950729_2235_0800G215570H.fits
ft950729_2235_0800G215670H.fits
ft950729_2235_0800G215770H.fits
ft950729_2235_0800G216373H.fits
ft950729_2235_0800G217070M.fits
ft950729_2235_0800G217170M.fits
ft950729_2235_0800G218470M.fits
ft950729_2235_0800G220770H.fits
ft950729_2235_0800G221870H.fits
ft950729_2235_0800G223070M.fits
ft950729_2235_0800G224270L.fits
ft950729_2235_0800G225270M.fits
ft950729_2235_0800G225370L.fits
ft950729_2235_0800G225499.fits
ft950729_2235_0800G225570M.fits
ft950729_2235_0800G225999.fits
ft950729_2235_0800G226270H.fits
ft950729_2235_0800G226370H.fits
ft950729_2235_0800G226470H.fits
ft950729_2235_0800G227270L.fits
ft950729_2235_0800G227370H.fits
ft950729_2235_0800G227470H.fits
ft950729_2235_0800G227570H.fits
ft950729_2235_0800G227670H.fits
ft950729_2235_0800G227770H.fits
ft950729_2235_0800G227870H.fits
ft950729_2235_0800G228570L.fits
ft950729_2235_0800G228670M.fits
ft950729_2235_0800G228770M.fits
ft950729_2235_0800G228870M.fits
ft950729_2235_0800G228970M.fits
ft950729_2235_0800G229399.fits
ft950729_2235_0800G229970L.fits
ft950729_2235_0800G230070M.fits
ft950729_2235_0800G230170M.fits
ft950729_2235_0800G230270M.fits
ft950729_2235_0800G230370M.fits
ft950729_2235_0800G231470L.fits
ft950729_2235_0800G231570H.fits
ft950729_2235_0800G231670H.fits
ft950729_2235_0800G231770H.fits
ft950729_2235_0800G231870H.fits
ft950729_2235_0800G231970H.fits
ft950729_2235_0800G232470H.fits
ft950729_2235_0800G232570H.fits
ft950729_2235_0800G232670H.fits
ft950729_2235_0800G233173H.fits
ft950729_2235_0800G233970M.fits
ft950729_2235_0800G234070L.fits
ft950729_2235_0800G234170L.fits
ft950729_2235_0800G234270H.fits
ft950729_2235_0800G234370H.fits
ft950729_2235_0800G301170L.fits
ft950729_2235_0800G301870M.fits
ft950729_2235_0800G308370M.fits
ft950729_2235_0800G308470L.fits
ft950729_2235_0800G308870M.fits
ft950729_2235_0800G308970L.fits
ft950729_2235_0800G309799.fits
ft950729_2235_0800G310099.fits
ft950729_2235_0800G310270H.fits
ft950729_2235_0800G310470H.fits
ft950729_2235_0800G310570H.fits
ft950729_2235_0800G310670H.fits
ft950729_2235_0800G310770H.fits
ft950729_2235_0800G310870H.fits
ft950729_2235_0800G311470M.fits
ft950729_2235_0800G312270L.fits
ft950729_2235_0800G312370M.fits
ft950729_2235_0800G312470M.fits
ft950729_2235_0800G312570M.fits
ft950729_2235_0800G312670M.fits
ft950729_2235_0800G313670L.fits
ft950729_2235_0800G313770M.fits
ft950729_2235_0800G313870M.fits
ft950729_2235_0800G313970M.fits
ft950729_2235_0800G314070M.fits
ft950729_2235_0800G314870L.fits
ft950729_2235_0800G314970M.fits
ft950729_2235_0800G315870H.fits
ft950729_2235_0800G315970H.fits
ft950729_2235_0800G316070H.fits
ft950729_2235_0800G316170H.fits
ft950729_2235_0800G316270H.fits
ft950729_2235_0800G316573H.fits
ft950729_2235_0800G317270M.fits
ft950729_2235_0800G317370M.fits
ft950729_2235_0800G318670M.fits
ft950729_2235_0800G320770H.fits
ft950729_2235_0800G323270M.fits
ft950729_2235_0800G324470L.fits
ft950729_2235_0800G324870H.fits
ft950729_2235_0800G325470M.fits
ft950729_2235_0800G325570L.fits
ft950729_2235_0800G325699.fits
ft950729_2235_0800G325770M.fits
ft950729_2235_0800G326199.fits
ft950729_2235_0800G326570H.fits
ft950729_2235_0800G326670H.fits
ft950729_2235_0800G326770H.fits
ft950729_2235_0800G327570L.fits
ft950729_2235_0800G327670H.fits
ft950729_2235_0800G327770H.fits
ft950729_2235_0800G327870H.fits
ft950729_2235_0800G327970H.fits
ft950729_2235_0800G328070H.fits
ft950729_2235_0800G328170H.fits
ft950729_2235_0800G328870L.fits
ft950729_2235_0800G328970M.fits
ft950729_2235_0800G329070M.fits
ft950729_2235_0800G329170M.fits
ft950729_2235_0800G329270M.fits
ft950729_2235_0800G329699.fits
ft950729_2235_0800G330270L.fits
ft950729_2235_0800G330370M.fits
ft950729_2235_0800G330470M.fits
ft950729_2235_0800G330570M.fits
ft950729_2235_0800G330670M.fits
ft950729_2235_0800G331770L.fits
ft950729_2235_0800G331870H.fits
ft950729_2235_0800G331970H.fits
ft950729_2235_0800G332070H.fits
ft950729_2235_0800G332170H.fits
ft950729_2235_0800G332270H.fits
ft950729_2235_0800G332770H.fits
ft950729_2235_0800G332870H.fits
ft950729_2235_0800G332970H.fits
ft950729_2235_0800G333373H.fits
ft950729_2235_0800G334170M.fits
ft950729_2235_0800G334270L.fits
ft950729_2235_0800G334370L.fits
ft950729_2235_0800G334470H.fits
ft950729_2235_0800G334570H.fits
ft950729_2235_0800G334670H.fits
ft950729_2235_0800G336270H.fits
ft950729_2235_0800S000202L.fits
ft950729_2235_0800S000302L.fits
ft950729_2235_0800S001702M.fits
ft950729_2235_0800S001901M.fits
ft950729_2235_0800S002202M.fits
ft950729_2235_0800S003301M.fits
ft950729_2235_0800S003501H.fits
ft950729_2235_0800S003702L.fits
ft950729_2235_0800S003901L.fits
ft950729_2235_0800S004101H.fits
ft950729_2235_0800S004302L.fits
ft950729_2235_0800S004501M.fits
ft950729_2235_0800S004802M.fits
ft950729_2235_0800S005302H.fits
ft950729_2235_0800S005701M.fits
ft950729_2235_0800S006201H.fits
ft950729_2235_0800S006402L.fits
ft950729_2235_0800S006902L.fits
ft950729_2235_0800S007002L.fits
ft950729_2235_0800S007102L.fits
ft950729_2235_0800S007301L.fits
ft950729_2235_0800S007602H.fits
ft950729_2235_0800S007702L.fits
ft950729_2235_0800S007802L.fits
ft950729_2235_0800S007902L.fits
ft950729_2235_0800S008199.fits
ft950729_2235_0800S008301M.fits
ft950729_2235_0800S008599.fits
ft950729_2235_0800S008802H.fits
ft950729_2235_0800S008902L.fits
ft950729_2235_0800S009002L.fits
ft950729_2235_0800S009102L.fits
ft950729_2235_0800S009602H.fits
ft950729_2235_0800S009702L.fits
ft950729_2235_0800S009802L.fits
ft950729_2235_0800S009902L.fits
ft950729_2235_0800S010402H.fits
ft950729_2235_0800S010702L.fits
ft950729_2235_0800S010802L.fits
ft950729_2235_0800S010902L.fits
ft950729_2235_0800S011502H.fits
ft950729_2235_0800S011802L.fits
ft950729_2235_0800S011902M.fits
ft950729_2235_0800S012399.fits
ft950729_2235_0800S013502H.fits
ft950729_2235_0800S014202H.fits
ft950729_2235_0800S014802H.fits
ft950729_2235_0800S015402H.fits
ft950729_2235_0800S015902H.fits
ft950729_2235_0800S016901H.fits
ft950729_2235_0800S017002H.fits
ft950729_2235_0800S018002M.fits
ft950729_2235_0800S018402H.fits
ft950729_2235_0800S018802L.fits
ft950729_2235_0800S019302L.fits
ft950729_2235_0800S019402L.fits
ft950729_2235_0800S019902H.fits
ft950729_2235_0800S020202L.fits
ft950729_2235_0800S020302L.fits
ft950729_2235_0800S020402L.fits
ft950729_2235_0800S020599.fits
ft950729_2235_0800S020899.fits
ft950729_2235_0800S021002H.fits
ft950729_2235_0800S021302L.fits
ft950729_2235_0800S021402L.fits
ft950729_2235_0800S021502L.fits
ft950729_2235_0800S021601L.fits
ft950729_2235_0800S021902H.fits
ft950729_2235_0800S022102L.fits
ft950729_2235_0800S022202L.fits
ft950729_2235_0800S022799.fits
ft950729_2235_0800S022902H.fits
ft950729_2235_0800S023202L.fits
ft950729_2235_0800S023302L.fits
ft950729_2235_0800S023802H.fits
ft950729_2235_0800S024302L.fits
ft950729_2235_0800S024401L.fits
ft950729_2235_0800S024501H.fits
ft950729_2235_0800S024799.fits
ft950729_2235_0800S025002H.fits
ft950729_2235_0800S025102M.fits
ft950729_2235_0800S025902H.fits
ft950729_2235_0800S026702H.fits
ft950729_2235_0800S101202M.fits
ft950729_2235_0800S101401M.fits
ft950729_2235_0800S102501M.fits
ft950729_2235_0800S102901L.fits
ft950729_2235_0800S103401M.fits
ft950729_2235_0800S104302H.fits
ft950729_2235_0800S104601M.fits
ft950729_2235_0800S105302L.fits
ft950729_2235_0800S105702L.fits
ft950729_2235_0800S105802L.fits
ft950729_2235_0800S106001L.fits
ft950729_2235_0800S106202H.fits
ft950729_2235_0800S106302L.fits
ft950729_2235_0800S106402L.fits
ft950729_2235_0800S106699.fits
ft950729_2235_0800S106801M.fits
ft950729_2235_0800S107099.fits
ft950729_2235_0800S107202H.fits
ft950729_2235_0800S107302L.fits
ft950729_2235_0800S107402L.fits
ft950729_2235_0800S107902L.fits
ft950729_2235_0800S108002L.fits
ft950729_2235_0800S108502H.fits
ft950729_2235_0800S108802L.fits
ft950729_2235_0800S109302H.fits
ft950729_2235_0800S109502L.fits
ft950729_2235_0800S109602M.fits
ft950729_2235_0800S110099.fits
ft950729_2235_0800S110902H.fits
ft950729_2235_0800S111402H.fits
ft950729_2235_0800S111802H.fits
ft950729_2235_0800S112202H.fits
ft950729_2235_0800S112602H.fits
ft950729_2235_0800S113402H.fits
ft950729_2235_0800S114202M.fits
ft950729_2235_0800S114802H.fits
ft950729_2235_0800S115102L.fits
ft950729_2235_0800S115902H.fits
ft950729_2235_0800S116102L.fits
ft950729_2235_0800S116202L.fits
ft950729_2235_0800S116399.fits
ft950729_2235_0800S116699.fits
ft950729_2235_0800S116802H.fits
ft950729_2235_0800S117002L.fits
ft950729_2235_0800S117102L.fits
ft950729_2235_0800S117201L.fits
ft950729_2235_0800S117402H.fits
ft950729_2235_0800S117602L.fits
ft950729_2235_0800S118199.fits
ft950729_2235_0800S118302H.fits
ft950729_2235_0800S119002H.fits
ft950729_2235_0800S119302L.fits
ft950729_2235_0800S119401L.fits
ft950729_2235_0800S119501H.fits
ft950729_2235_0800S119799.fits
ft950729_2235_0800S119902H.fits
ft950729_2235_0800S120702H.fits
ft950729_2235_0800S121302H.fits
-> Checking for empty GTI extensions
-> Checking housekeeping files for valid TSTART and TSTOP
-> Appending ALLGTI extensions to housekeeping files
-> Merging GTIs from the following files:
ft950729_2235_0800S000102M.fits[3]
ft950729_2235_0800S000402L.fits[3]
ft950729_2235_0800S000502L.fits[3]
ft950729_2235_0800S000602M.fits[3]
ft950729_2235_0800S000702M.fits[3]
ft950729_2235_0800S000802L.fits[3]
ft950729_2235_0800S000902L.fits[3]
ft950729_2235_0800S001002L.fits[3]
ft950729_2235_0800S001102L.fits[3]
ft950729_2235_0800S001202M.fits[3]
ft950729_2235_0800S001302M.fits[3]
ft950729_2235_0800S001402L.fits[3]
ft950729_2235_0800S001502L.fits[3]
ft950729_2235_0800S001602M.fits[3]
ft950729_2235_0800S001802M.fits[3]
ft950729_2235_0800S002001H.fits[3]
ft950729_2235_0800S002101H.fits[3]
ft950729_2235_0800S002302L.fits[3]
ft950729_2235_0800S002402L.fits[3]
ft950729_2235_0800S002502L.fits[3]
ft950729_2235_0800S002602L.fits[3]
ft950729_2235_0800S002702M.fits[3]
ft950729_2235_0800S002801H.fits[3]
ft950729_2235_0800S002902M.fits[3]
ft950729_2235_0800S003002M.fits[3]
ft950729_2235_0800S003102L.fits[3]
ft950729_2235_0800S003202M.fits[3]
ft950729_2235_0800S003401H.fits[3]
ft950729_2235_0800S003602M.fits[3]
ft950729_2235_0800S003802L.fits[3]
ft950729_2235_0800S004001H.fits[3]
ft950729_2235_0800S004202M.fits[3]
ft950729_2235_0800S004402M.fits[3]
ft950729_2235_0800S004601H.fits[3]
ft950729_2235_0800S004701H.fits[3]
ft950729_2235_0800S004902L.fits[3]
ft950729_2235_0800S005002M.fits[3]
ft950729_2235_0800S005101H.fits[3]
ft950729_2235_0800S005201H.fits[3]
ft950729_2235_0800S005402L.fits[3]
ft950729_2235_0800S005502M.fits[3]
ft950729_2235_0800S005602M.fits[3]
ft950729_2235_0800S005801H.fits[3]
ft950729_2235_0800S005901H.fits[3]
ft950729_2235_0800S006001H.fits[3]
ft950729_2235_0800S006101H.fits[3]
ft950729_2235_0800S006302M.fits[3]
ft950729_2235_0800S006502L.fits[3]
ft950729_2235_0800S006602L.fits[3]
ft950729_2235_0800S006702M.fits[3]
ft950729_2235_0800S006802M.fits[3]
ft950729_2235_0800S007202L.fits[3]
ft950729_2235_0800S007401H.fits[3]
ft950729_2235_0800S007501H.fits[3]
ft950729_2235_0800S008002L.fits[3]
ft950729_2235_0800S008202M.fits[3]
ft950729_2235_0800S008401H.fits[3]
ft950729_2235_0800S008601H.fits[3]
ft950729_2235_0800S008701H.fits[3]
ft950729_2235_0800S009202M.fits[3]
ft950729_2235_0800S009301M.fits[3]
ft950729_2235_0800S009401H.fits[3]
ft950729_2235_0800S009501H.fits[3]
ft950729_2235_0800S010002L.fits[3]
ft950729_2235_0800S010102M.fits[3]
ft950729_2235_0800S010201M.fits[3]
ft950729_2235_0800S010301H.fits[3]
ft950729_2235_0800S010502M.fits[3]
ft950729_2235_0800S010602M.fits[3]
ft950729_2235_0800S011002L.fits[3]
ft950729_2235_0800S011102M.fits[3]
ft950729_2235_0800S011201M.fits[3]
ft950729_2235_0800S011301H.fits[3]
ft950729_2235_0800S011401H.fits[3]
ft950729_2235_0800S011602L.fits[3]
ft950729_2235_0800S011702L.fits[3]
ft950729_2235_0800S012002M.fits[3]
ft950729_2235_0800S012101M.fits[3]
ft950729_2235_0800S012201H.fits[3]
ft950729_2235_0800S012401H.fits[3]
ft950729_2235_0800S012501H.fits[3]
ft950729_2235_0800S012602H.fits[3]
ft950729_2235_0800S012702L.fits[3]
ft950729_2235_0800S012802M.fits[3]
ft950729_2235_0800S012902M.fits[3]
ft950729_2235_0800S013002M.fits[3]
ft950729_2235_0800S013102M.fits[3]
ft950729_2235_0800S013201M.fits[3]
ft950729_2235_0800S013301H.fits[3]
ft950729_2235_0800S013401H.fits[3]
ft950729_2235_0800S013602L.fits[3]
ft950729_2235_0800S013702M.fits[3]
ft950729_2235_0800S013802M.fits[3]
ft950729_2235_0800S013901M.fits[3]
ft950729_2235_0800S014001H.fits[3]
ft950729_2235_0800S014101H.fits[3]
ft950729_2235_0800S014302M.fits[3]
ft950729_2235_0800S014402M.fits[3]
ft950729_2235_0800S014501M.fits[3]
ft950729_2235_0800S014601H.fits[3]
ft950729_2235_0800S014701H.fits[3]
ft950729_2235_0800S014902M.fits[3]
ft950729_2235_0800S015002M.fits[3]
ft950729_2235_0800S015101M.fits[3]
ft950729_2235_0800S015201H.fits[3]
ft950729_2235_0800S015301H.fits[3]
ft950729_2235_0800S015502M.fits[3]
ft950729_2235_0800S015602M.fits[3]
ft950729_2235_0800S015701M.fits[3]
ft950729_2235_0800S015801H.fits[3]
ft950729_2235_0800S016002M.fits[3]
ft950729_2235_0800S016102M.fits[3]
ft950729_2235_0800S016202L.fits[3]
ft950729_2235_0800S016302M.fits[3]
ft950729_2235_0800S016402M.fits[3]
ft950729_2235_0800S016501M.fits[3]
ft950729_2235_0800S016601H.fits[3]
ft950729_2235_0800S016701H.fits[3]
ft950729_2235_0800S016801H.fits[3]
ft950729_2235_0800S017102M.fits[3]
ft950729_2235_0800S017202L.fits[3]
ft950729_2235_0800S017302M.fits[3]
ft950729_2235_0800S017402M.fits[3]
ft950729_2235_0800S017502M.fits[3]
ft950729_2235_0800S017602M.fits[3]
ft950729_2235_0800S017702M.fits[3]
ft950729_2235_0800S017801H.fits[3]
ft950729_2235_0800S017901H.fits[3]
ft950729_2235_0800S018101H.fits[3]
ft950729_2235_0800S018201H.fits[3]
ft950729_2235_0800S018301H.fits[3]
ft950729_2235_0800S018502M.fits[3]
ft950729_2235_0800S018602M.fits[3]
ft950729_2235_0800S018702L.fits[3]
ft950729_2235_0800S018902L.fits[3]
ft950729_2235_0800S019002L.fits[3]
ft950729_2235_0800S019102M.fits[3]
ft950729_2235_0800S019202M.fits[3]
ft950729_2235_0800S019502L.fits[3]
ft950729_2235_0800S019602L.fits[3]
ft950729_2235_0800S019701L.fits[3]
ft950729_2235_0800S019801H.fits[3]
ft950729_2235_0800S020002M.fits[3]
ft950729_2235_0800S020102M.fits[3]
ft950729_2235_0800S020602M.fits[3]
ft950729_2235_0800S020701H.fits[3]
ft950729_2235_0800S020901H.fits[3]
ft950729_2235_0800S021102M.fits[3]
ft950729_2235_0800S021202M.fits[3]
ft950729_2235_0800S021701H.fits[3]
ft950729_2235_0800S021801H.fits[3]
ft950729_2235_0800S022002M.fits[3]
ft950729_2235_0800S022302L.fits[3]
ft950729_2235_0800S022402M.fits[3]
ft950729_2235_0800S022501M.fits[3]
ft950729_2235_0800S022601H.fits[3]
ft950729_2235_0800S022801H.fits[3]
ft950729_2235_0800S023002M.fits[3]
ft950729_2235_0800S023102M.fits[3]
ft950729_2235_0800S023402L.fits[3]
ft950729_2235_0800S023502M.fits[3]
ft950729_2235_0800S023601M.fits[3]
ft950729_2235_0800S023701H.fits[3]
ft950729_2235_0800S023902M.fits[3]
ft950729_2235_0800S024002M.fits[3]
ft950729_2235_0800S024102L.fits[3]
ft950729_2235_0800S024202L.fits[3]
ft950729_2235_0800S024601H.fits[3]
ft950729_2235_0800S024801H.fits[3]
ft950729_2235_0800S024901H.fits[3]
ft950729_2235_0800S025202L.fits[3]
ft950729_2235_0800S025302M.fits[3]
ft950729_2235_0800S025402M.fits[3]
ft950729_2235_0800S025502L.fits[3]
ft950729_2235_0800S025602L.fits[3]
ft950729_2235_0800S025701L.fits[3]
ft950729_2235_0800S025801H.fits[3]
ft950729_2235_0800S026002M.fits[3]
ft950729_2235_0800S026102M.fits[3]
ft950729_2235_0800S026202L.fits[3]
ft950729_2235_0800S026302M.fits[3]
ft950729_2235_0800S026402M.fits[3]
ft950729_2235_0800S026501M.fits[3]
ft950729_2235_0800S026601H.fits[3]
ft950729_2235_0800S026802M.fits[3]
ft950729_2235_0800S026902M.fits[3]
ft950729_2235_0800S027002L.fits[3]
ft950729_2235_0800S027102M.fits[3]
ft950729_2235_0800S027202M.fits[3]
ft950729_2235_0800S027301M.fits[3]
ft950729_2235_0800S027401H.fits[3]
ft950729_2235_0800S027502M.fits[3]
ft950729_2235_0800S027602M.fits[3]
-> Merging GTIs from the following files:
ft950729_2235_0800S100102M.fits[3]
ft950729_2235_0800S100202L.fits[3]
ft950729_2235_0800S100302L.fits[3]
ft950729_2235_0800S100402L.fits[3]
ft950729_2235_0800S100502M.fits[3]
ft950729_2235_0800S100602L.fits[3]
ft950729_2235_0800S100702L.fits[3]
ft950729_2235_0800S100802L.fits[3]
ft950729_2235_0800S100902M.fits[3]
ft950729_2235_0800S101002L.fits[3]
ft950729_2235_0800S101102M.fits[3]
ft950729_2235_0800S101302M.fits[3]
ft950729_2235_0800S101501H.fits[3]
ft950729_2235_0800S101602M.fits[3]
ft950729_2235_0800S101702L.fits[3]
ft950729_2235_0800S101802L.fits[3]
ft950729_2235_0800S101902L.fits[3]
ft950729_2235_0800S102002M.fits[3]
ft950729_2235_0800S102101H.fits[3]
ft950729_2235_0800S102202M.fits[3]
ft950729_2235_0800S102302L.fits[3]
ft950729_2235_0800S102402M.fits[3]
ft950729_2235_0800S102601H.fits[3]
ft950729_2235_0800S102702M.fits[3]
ft950729_2235_0800S102802L.fits[3]
ft950729_2235_0800S103001H.fits[3]
ft950729_2235_0800S103102M.fits[3]
ft950729_2235_0800S103202L.fits[3]
ft950729_2235_0800S103302M.fits[3]
ft950729_2235_0800S103501H.fits[3]
ft950729_2235_0800S103601H.fits[3]
ft950729_2235_0800S103702M.fits[3]
ft950729_2235_0800S103802L.fits[3]
ft950729_2235_0800S103902M.fits[3]
ft950729_2235_0800S104001H.fits[3]
ft950729_2235_0800S104101H.fits[3]
ft950729_2235_0800S104201H.fits[3]
ft950729_2235_0800S104402L.fits[3]
ft950729_2235_0800S104502M.fits[3]
ft950729_2235_0800S104701H.fits[3]
ft950729_2235_0800S104801H.fits[3]
ft950729_2235_0800S104901H.fits[3]
ft950729_2235_0800S105001H.fits[3]
ft950729_2235_0800S105101H.fits[3]
ft950729_2235_0800S105202M.fits[3]
ft950729_2235_0800S105402L.fits[3]
ft950729_2235_0800S105502L.fits[3]
ft950729_2235_0800S105602M.fits[3]
ft950729_2235_0800S105902L.fits[3]
ft950729_2235_0800S106101H.fits[3]
ft950729_2235_0800S106502L.fits[3]
ft950729_2235_0800S106702M.fits[3]
ft950729_2235_0800S106901H.fits[3]
ft950729_2235_0800S107101H.fits[3]
ft950729_2235_0800S107502M.fits[3]
ft950729_2235_0800S107601M.fits[3]
ft950729_2235_0800S107701H.fits[3]
ft950729_2235_0800S107802H.fits[3]
ft950729_2235_0800S108102L.fits[3]
ft950729_2235_0800S108202M.fits[3]
ft950729_2235_0800S108301M.fits[3]
ft950729_2235_0800S108401H.fits[3]
ft950729_2235_0800S108602M.fits[3]
ft950729_2235_0800S108702L.fits[3]
ft950729_2235_0800S108902L.fits[3]
ft950729_2235_0800S109002M.fits[3]
ft950729_2235_0800S109101M.fits[3]
ft950729_2235_0800S109201H.fits[3]
ft950729_2235_0800S109402L.fits[3]
ft950729_2235_0800S109702M.fits[3]
ft950729_2235_0800S109801M.fits[3]
ft950729_2235_0800S109901H.fits[3]
ft950729_2235_0800S110101H.fits[3]
ft950729_2235_0800S110202H.fits[3]
ft950729_2235_0800S110302L.fits[3]
ft950729_2235_0800S110402M.fits[3]
ft950729_2235_0800S110502M.fits[3]
ft950729_2235_0800S110602M.fits[3]
ft950729_2235_0800S110701M.fits[3]
ft950729_2235_0800S110801H.fits[3]
ft950729_2235_0800S111002L.fits[3]
ft950729_2235_0800S111102M.fits[3]
ft950729_2235_0800S111201M.fits[3]
ft950729_2235_0800S111301H.fits[3]
ft950729_2235_0800S111502M.fits[3]
ft950729_2235_0800S111601M.fits[3]
ft950729_2235_0800S111701H.fits[3]
ft950729_2235_0800S111902M.fits[3]
ft950729_2235_0800S112001M.fits[3]
ft950729_2235_0800S112101H.fits[3]
ft950729_2235_0800S112302M.fits[3]
ft950729_2235_0800S112401M.fits[3]
ft950729_2235_0800S112501H.fits[3]
ft950729_2235_0800S112702M.fits[3]
ft950729_2235_0800S112802L.fits[3]
ft950729_2235_0800S112902M.fits[3]
ft950729_2235_0800S113001M.fits[3]
ft950729_2235_0800S113101H.fits[3]
ft950729_2235_0800S113201H.fits[3]
ft950729_2235_0800S113301H.fits[3]
ft950729_2235_0800S113502M.fits[3]
ft950729_2235_0800S113602L.fits[3]
ft950729_2235_0800S113702M.fits[3]
ft950729_2235_0800S113802M.fits[3]
ft950729_2235_0800S113902M.fits[3]
ft950729_2235_0800S114002M.fits[3]
ft950729_2235_0800S114101H.fits[3]
ft950729_2235_0800S114301H.fits[3]
ft950729_2235_0800S114401H.fits[3]
ft950729_2235_0800S114501H.fits[3]
ft950729_2235_0800S114601H.fits[3]
ft950729_2235_0800S114701H.fits[3]
ft950729_2235_0800S114902M.fits[3]
ft950729_2235_0800S115002L.fits[3]
ft950729_2235_0800S115202L.fits[3]
ft950729_2235_0800S115302M.fits[3]
ft950729_2235_0800S115402L.fits[3]
ft950729_2235_0800S115502L.fits[3]
ft950729_2235_0800S115602L.fits[3]
ft950729_2235_0800S115701L.fits[3]
ft950729_2235_0800S115801H.fits[3]
ft950729_2235_0800S116002M.fits[3]
ft950729_2235_0800S116402M.fits[3]
ft950729_2235_0800S116501H.fits[3]
ft950729_2235_0800S116701H.fits[3]
ft950729_2235_0800S116902M.fits[3]
ft950729_2235_0800S117301H.fits[3]
ft950729_2235_0800S117502M.fits[3]
ft950729_2235_0800S117702L.fits[3]
ft950729_2235_0800S117802M.fits[3]
ft950729_2235_0800S117901M.fits[3]
ft950729_2235_0800S118001H.fits[3]
ft950729_2235_0800S118201H.fits[3]
ft950729_2235_0800S118402M.fits[3]
ft950729_2235_0800S118502L.fits[3]
ft950729_2235_0800S118602L.fits[3]
ft950729_2235_0800S118702M.fits[3]
ft950729_2235_0800S118801M.fits[3]
ft950729_2235_0800S118901H.fits[3]
ft950729_2235_0800S119102M.fits[3]
ft950729_2235_0800S119202L.fits[3]
ft950729_2235_0800S119601H.fits[3]
ft950729_2235_0800S119801H.fits[3]
ft950729_2235_0800S120002M.fits[3]
ft950729_2235_0800S120102L.fits[3]
ft950729_2235_0800S120202M.fits[3]
ft950729_2235_0800S120302L.fits[3]
ft950729_2235_0800S120402L.fits[3]
ft950729_2235_0800S120501L.fits[3]
ft950729_2235_0800S120601H.fits[3]
ft950729_2235_0800S120802M.fits[3]
ft950729_2235_0800S120902L.fits[3]
ft950729_2235_0800S121002M.fits[3]
ft950729_2235_0800S121101M.fits[3]
ft950729_2235_0800S121201H.fits[3]
ft950729_2235_0800S121402M.fits[3]
ft950729_2235_0800S121502L.fits[3]
ft950729_2235_0800S121602M.fits[3]
ft950729_2235_0800S121701M.fits[3]
ft950729_2235_0800S121801H.fits[3]
ft950729_2235_0800S121902M.fits[3]
-> Merging GTIs from the following files:
ft950729_2235_0800G200170M.fits[3]
ft950729_2235_0800G200270L.fits[3]
ft950729_2235_0800G200370L.fits[3]
ft950729_2235_0800G200470L.fits[3]
ft950729_2235_0800G200570L.fits[3]
ft950729_2235_0800G200670M.fits[3]
ft950729_2235_0800G200770M.fits[3]
ft950729_2235_0800G200870M.fits[3]
ft950729_2235_0800G200970M.fits[3]
ft950729_2235_0800G201070L.fits[3]
ft950729_2235_0800G201270L.fits[3]
ft950729_2235_0800G201370M.fits[3]
ft950729_2235_0800G201470M.fits[3]
ft950729_2235_0800G201570M.fits[3]
ft950729_2235_0800G201670M.fits[3]
ft950729_2235_0800G201770L.fits[3]
ft950729_2235_0800G201970M.fits[3]
ft950729_2235_0800G202070M.fits[3]
ft950729_2235_0800G202170H.fits[3]
ft950729_2235_0800G202270M.fits[3]
ft950729_2235_0800G202370L.fits[3]
ft950729_2235_0800G202470L.fits[3]
ft950729_2235_0800G202570L.fits[3]
ft950729_2235_0800G202670L.fits[3]
ft950729_2235_0800G202770M.fits[3]
ft950729_2235_0800G202870M.fits[3]
ft950729_2235_0800G202970M.fits[3]
ft950729_2235_0800G203070M.fits[3]
ft950729_2235_0800G203170H.fits[3]
ft950729_2235_0800G203270M.fits[3]
ft950729_2235_0800G203370L.fits[3]
ft950729_2235_0800G203470L.fits[3]
ft950729_2235_0800G203570M.fits[3]
ft950729_2235_0800G203670H.fits[3]
ft950729_2235_0800G203770M.fits[3]
ft950729_2235_0800G203870L.fits[3]
ft950729_2235_0800G203970L.fits[3]
ft950729_2235_0800G204070H.fits[3]
ft950729_2235_0800G204170H.fits[3]
ft950729_2235_0800G204270H.fits[3]
ft950729_2235_0800G204370H.fits[3]
ft950729_2235_0800G204470M.fits[3]
ft950729_2235_0800G204570L.fits[3]
ft950729_2235_0800G204670L.fits[3]
ft950729_2235_0800G204770M.fits[3]
ft950729_2235_0800G204870M.fits[3]
ft950729_2235_0800G204970M.fits[3]
ft950729_2235_0800G205070M.fits[3]
ft950729_2235_0800G205170H.fits[3]
ft950729_2235_0800G205270H.fits[3]
ft950729_2235_0800G205370H.fits[3]
ft950729_2235_0800G205470M.fits[3]
ft950729_2235_0800G205570L.fits[3]
ft950729_2235_0800G205670L.fits[3]
ft950729_2235_0800G205770M.fits[3]
ft950729_2235_0800G205870H.fits[3]
ft950729_2235_0800G205970L.fits[3]
ft950729_2235_0800G206070L.fits[3]
ft950729_2235_0800G206170M.fits[3]
ft950729_2235_0800G206270M.fits[3]
ft950729_2235_0800G206370M.fits[3]
ft950729_2235_0800G206470M.fits[3]
ft950729_2235_0800G206570H.fits[3]
ft950729_2235_0800G206670H.fits[3]
ft950729_2235_0800G206770H.fits[3]
ft950729_2235_0800G206870H.fits[3]
ft950729_2235_0800G206970H.fits[3]
ft950729_2235_0800G207070H.fits[3]
ft950729_2235_0800G207170H.fits[3]
ft950729_2235_0800G207270H.fits[3]
ft950729_2235_0800G207370H.fits[3]
ft950729_2235_0800G207470H.fits[3]
ft950729_2235_0800G207570H.fits[3]
ft950729_2235_0800G207670H.fits[3]
ft950729_2235_0800G207770M.fits[3]
ft950729_2235_0800G207870M.fits[3]
ft950729_2235_0800G208170L.fits[3]
ft950729_2235_0800G208270M.fits[3]
ft950729_2235_0800G208370M.fits[3]
ft950729_2235_0800G208470M.fits[3]
ft950729_2235_0800G208570M.fits[3]
ft950729_2235_0800G208870L.fits[3]
ft950729_2235_0800G208970H.fits[3]
ft950729_2235_0800G209170H.fits[3]
ft950729_2235_0800G209270H.fits[3]
ft950729_2235_0800G209370L.fits[3]
ft950729_2235_0800G209470L.fits[3]
ft950729_2235_0800G209670M.fits[3]
ft950729_2235_0800G209770H.fits[3]
ft950729_2235_0800G209970H.fits[3]
ft950729_2235_0800G210070H.fits[3]
ft950729_2235_0800G210570H.fits[3]
ft950729_2235_0800G210670H.fits[3]
ft950729_2235_0800G210770H.fits[3]
ft950729_2235_0800G210870H.fits[3]
ft950729_2235_0800G210970H.fits[3]
ft950729_2235_0800G211070L.fits[3]
ft950729_2235_0800G211370M.fits[3]
ft950729_2235_0800G211470M.fits[3]
ft950729_2235_0800G211570H.fits[3]
ft950729_2235_0800G211670H.fits[3]
ft950729_2235_0800G211770H.fits[3]
ft950729_2235_0800G211870H.fits[3]
ft950729_2235_0800G211970L.fits[3]
ft950729_2235_0800G212570M.fits[3]
ft950729_2235_0800G212670M.fits[3]
ft950729_2235_0800G212770H.fits[3]
ft950729_2235_0800G212870H.fits[3]
ft950729_2235_0800G212970M.fits[3]
ft950729_2235_0800G213070M.fits[3]
ft950729_2235_0800G213170L.fits[3]
ft950729_2235_0800G213270L.fits[3]
ft950729_2235_0800G213870M.fits[3]
ft950729_2235_0800G213970M.fits[3]
ft950729_2235_0800G214070H.fits[3]
ft950729_2235_0800G214170H.fits[3]
ft950729_2235_0800G214270H.fits[3]
ft950729_2235_0800G214370H.fits[3]
ft950729_2235_0800G214470L.fits[3]
ft950729_2235_0800G214770M.fits[3]
ft950729_2235_0800G214870M.fits[3]
ft950729_2235_0800G214970H.fits[3]
ft950729_2235_0800G215070H.fits[3]
ft950729_2235_0800G215170H.fits[3]
ft950729_2235_0800G215270H.fits[3]
ft950729_2235_0800G215870H.fits[3]
ft950729_2235_0800G215970H.fits[3]
ft950729_2235_0800G216070H.fits[3]
ft950729_2235_0800G216170H.fits[3]
ft950729_2235_0800G216270H.fits[3]
ft950729_2235_0800G216470H.fits[3]
ft950729_2235_0800G216570L.fits[3]
ft950729_2235_0800G216670M.fits[3]
ft950729_2235_0800G216770M.fits[3]
ft950729_2235_0800G216870M.fits[3]
ft950729_2235_0800G216970M.fits[3]
ft950729_2235_0800G217270M.fits[3]
ft950729_2235_0800G217370M.fits[3]
ft950729_2235_0800G217470H.fits[3]
ft950729_2235_0800G217570H.fits[3]
ft950729_2235_0800G217670H.fits[3]
ft950729_2235_0800G217770H.fits[3]
ft950729_2235_0800G217870L.fits[3]
ft950729_2235_0800G217970M.fits[3]
ft950729_2235_0800G218070M.fits[3]
ft950729_2235_0800G218170M.fits[3]
ft950729_2235_0800G218270M.fits[3]
ft950729_2235_0800G218370M.fits[3]
ft950729_2235_0800G218570M.fits[3]
ft950729_2235_0800G218670M.fits[3]
ft950729_2235_0800G218770H.fits[3]
ft950729_2235_0800G218870H.fits[3]
ft950729_2235_0800G218970H.fits[3]
ft950729_2235_0800G219070H.fits[3]
ft950729_2235_0800G219170M.fits[3]
ft950729_2235_0800G219270M.fits[3]
ft950729_2235_0800G219370H.fits[3]
ft950729_2235_0800G219470H.fits[3]
ft950729_2235_0800G219570H.fits[3]
ft950729_2235_0800G219670H.fits[3]
ft950729_2235_0800G219770M.fits[3]
ft950729_2235_0800G219870M.fits[3]
ft950729_2235_0800G219970H.fits[3]
ft950729_2235_0800G220070H.fits[3]
ft950729_2235_0800G220170H.fits[3]
ft950729_2235_0800G220270H.fits[3]
ft950729_2235_0800G220370M.fits[3]
ft950729_2235_0800G220470M.fits[3]
ft950729_2235_0800G220570H.fits[3]
ft950729_2235_0800G220670H.fits[3]
ft950729_2235_0800G220870H.fits[3]
ft950729_2235_0800G220970M.fits[3]
ft950729_2235_0800G221070M.fits[3]
ft950729_2235_0800G221170L.fits[3]
ft950729_2235_0800G221270L.fits[3]
ft950729_2235_0800G221370M.fits[3]
ft950729_2235_0800G221470H.fits[3]
ft950729_2235_0800G221570H.fits[3]
ft950729_2235_0800G221670H.fits[3]
ft950729_2235_0800G221770H.fits[3]
ft950729_2235_0800G221970H.fits[3]
ft950729_2235_0800G222070H.fits[3]
ft950729_2235_0800G222170H.fits[3]
ft950729_2235_0800G222270H.fits[3]
ft950729_2235_0800G222370H.fits[3]
ft950729_2235_0800G222470M.fits[3]
ft950729_2235_0800G222570M.fits[3]
ft950729_2235_0800G222670L.fits[3]
ft950729_2235_0800G222770L.fits[3]
ft950729_2235_0800G222870M.fits[3]
ft950729_2235_0800G222970H.fits[3]
ft950729_2235_0800G223170H.fits[3]
ft950729_2235_0800G223270H.fits[3]
ft950729_2235_0800G223370H.fits[3]
ft950729_2235_0800G223470M.fits[3]
ft950729_2235_0800G223570M.fits[3]
ft950729_2235_0800G223670L.fits[3]
ft950729_2235_0800G223770M.fits[3]
ft950729_2235_0800G223870M.fits[3]
ft950729_2235_0800G223970M.fits[3]
ft950729_2235_0800G224070M.fits[3]
ft950729_2235_0800G224170L.fits[3]
ft950729_2235_0800G224370L.fits[3]
ft950729_2235_0800G224470L.fits[3]
ft950729_2235_0800G224570H.fits[3]
ft950729_2235_0800G224670H.fits[3]
ft950729_2235_0800G224770H.fits[3]
ft950729_2235_0800G224870H.fits[3]
ft950729_2235_0800G224970M.fits[3]
ft950729_2235_0800G225070M.fits[3]
ft950729_2235_0800G225170M.fits[3]
ft950729_2235_0800G225670M.fits[3]
ft950729_2235_0800G225770M.fits[3]
ft950729_2235_0800G225870H.fits[3]
ft950729_2235_0800G226070H.fits[3]
ft950729_2235_0800G226170H.fits[3]
ft950729_2235_0800G226570H.fits[3]
ft950729_2235_0800G226670H.fits[3]
ft950729_2235_0800G226770H.fits[3]
ft950729_2235_0800G226870M.fits[3]
ft950729_2235_0800G226970M.fits[3]
ft950729_2235_0800G227070L.fits[3]
ft950729_2235_0800G227170L.fits[3]
ft950729_2235_0800G227970H.fits[3]
ft950729_2235_0800G228070H.fits[3]
ft950729_2235_0800G228170M.fits[3]
ft950729_2235_0800G228270M.fits[3]
ft950729_2235_0800G228370L.fits[3]
ft950729_2235_0800G228470L.fits[3]
ft950729_2235_0800G229070M.fits[3]
ft950729_2235_0800G229170M.fits[3]
ft950729_2235_0800G229270H.fits[3]
ft950729_2235_0800G229470H.fits[3]
ft950729_2235_0800G229570M.fits[3]
ft950729_2235_0800G229670M.fits[3]
ft950729_2235_0800G229770L.fits[3]
ft950729_2235_0800G229870L.fits[3]
ft950729_2235_0800G230470M.fits[3]
ft950729_2235_0800G230570M.fits[3]
ft950729_2235_0800G230670H.fits[3]
ft950729_2235_0800G230770H.fits[3]
ft950729_2235_0800G230870H.fits[3]
ft950729_2235_0800G230970H.fits[3]
ft950729_2235_0800G231070M.fits[3]
ft950729_2235_0800G231170M.fits[3]
ft950729_2235_0800G231270L.fits[3]
ft950729_2235_0800G231370L.fits[3]
ft950729_2235_0800G232070H.fits[3]
ft950729_2235_0800G232170H.fits[3]
ft950729_2235_0800G232270H.fits[3]
ft950729_2235_0800G232370H.fits[3]
ft950729_2235_0800G232770H.fits[3]
ft950729_2235_0800G232870H.fits[3]
ft950729_2235_0800G232970H.fits[3]
ft950729_2235_0800G233070H.fits[3]
ft950729_2235_0800G233270H.fits[3]
ft950729_2235_0800G233370M.fits[3]
ft950729_2235_0800G233470M.fits[3]
ft950729_2235_0800G233570L.fits[3]
ft950729_2235_0800G233670L.fits[3]
ft950729_2235_0800G233770M.fits[3]
ft950729_2235_0800G233870M.fits[3]
ft950729_2235_0800G234470H.fits[3]
ft950729_2235_0800G234570H.fits[3]
ft950729_2235_0800G234670H.fits[3]
ft950729_2235_0800G234770M.fits[3]
ft950729_2235_0800G234870M.fits[3]
ft950729_2235_0800G234970L.fits[3]
ft950729_2235_0800G235070L.fits[3]
ft950729_2235_0800G235170M.fits[3]
ft950729_2235_0800G235270H.fits[3]
ft950729_2235_0800G235370H.fits[3]
ft950729_2235_0800G235470H.fits[3]
ft950729_2235_0800G235570H.fits[3]
ft950729_2235_0800G235670M.fits[3]
ft950729_2235_0800G235770M.fits[3]
ft950729_2235_0800G235870L.fits[3]
ft950729_2235_0800G235970M.fits[3]
ft950729_2235_0800G236070H.fits[3]
ft950729_2235_0800G236170H.fits[3]
ft950729_2235_0800G236270H.fits[3]
ft950729_2235_0800G236370H.fits[3]
ft950729_2235_0800G236470M.fits[3]
-> Merging GTIs from the following files:
ft950729_2235_0800G300170M.fits[3]
ft950729_2235_0800G300270L.fits[3]
ft950729_2235_0800G300370L.fits[3]
ft950729_2235_0800G300470L.fits[3]
ft950729_2235_0800G300570L.fits[3]
ft950729_2235_0800G300670M.fits[3]
ft950729_2235_0800G300770M.fits[3]
ft950729_2235_0800G300870M.fits[3]
ft950729_2235_0800G300970M.fits[3]
ft950729_2235_0800G301070L.fits[3]
ft950729_2235_0800G301270L.fits[3]
ft950729_2235_0800G301370M.fits[3]
ft950729_2235_0800G301470M.fits[3]
ft950729_2235_0800G301570M.fits[3]
ft950729_2235_0800G301670M.fits[3]
ft950729_2235_0800G301770L.fits[3]
ft950729_2235_0800G301970M.fits[3]
ft950729_2235_0800G302070M.fits[3]
ft950729_2235_0800G302170H.fits[3]
ft950729_2235_0800G302270M.fits[3]
ft950729_2235_0800G302370L.fits[3]
ft950729_2235_0800G302470L.fits[3]
ft950729_2235_0800G302570L.fits[3]
ft950729_2235_0800G302670L.fits[3]
ft950729_2235_0800G302770M.fits[3]
ft950729_2235_0800G302870M.fits[3]
ft950729_2235_0800G302970M.fits[3]
ft950729_2235_0800G303070M.fits[3]
ft950729_2235_0800G303170H.fits[3]
ft950729_2235_0800G303270M.fits[3]
ft950729_2235_0800G303370L.fits[3]
ft950729_2235_0800G303470L.fits[3]
ft950729_2235_0800G303570M.fits[3]
ft950729_2235_0800G303670H.fits[3]
ft950729_2235_0800G303770M.fits[3]
ft950729_2235_0800G303870L.fits[3]
ft950729_2235_0800G303970L.fits[3]
ft950729_2235_0800G304070H.fits[3]
ft950729_2235_0800G304170H.fits[3]
ft950729_2235_0800G304270H.fits[3]
ft950729_2235_0800G304370H.fits[3]
ft950729_2235_0800G304470M.fits[3]
ft950729_2235_0800G304570L.fits[3]
ft950729_2235_0800G304670L.fits[3]
ft950729_2235_0800G304770M.fits[3]
ft950729_2235_0800G304870M.fits[3]
ft950729_2235_0800G304970M.fits[3]
ft950729_2235_0800G305070M.fits[3]
ft950729_2235_0800G305170H.fits[3]
ft950729_2235_0800G305270H.fits[3]
ft950729_2235_0800G305370H.fits[3]
ft950729_2235_0800G305470M.fits[3]
ft950729_2235_0800G305570L.fits[3]
ft950729_2235_0800G305670L.fits[3]
ft950729_2235_0800G305770M.fits[3]
ft950729_2235_0800G305870H.fits[3]
ft950729_2235_0800G305970H.fits[3]
ft950729_2235_0800G306070H.fits[3]
ft950729_2235_0800G306170L.fits[3]
ft950729_2235_0800G306270L.fits[3]
ft950729_2235_0800G306370M.fits[3]
ft950729_2235_0800G306470M.fits[3]
ft950729_2235_0800G306570M.fits[3]
ft950729_2235_0800G306670M.fits[3]
ft950729_2235_0800G306770H.fits[3]
ft950729_2235_0800G306870H.fits[3]
ft950729_2235_0800G306970H.fits[3]
ft950729_2235_0800G307070H.fits[3]
ft950729_2235_0800G307170H.fits[3]
ft950729_2235_0800G307270H.fits[3]
ft950729_2235_0800G307370H.fits[3]
ft950729_2235_0800G307470H.fits[3]
ft950729_2235_0800G307570H.fits[3]
ft950729_2235_0800G307670H.fits[3]
ft950729_2235_0800G307770H.fits[3]
ft950729_2235_0800G307870H.fits[3]
ft950729_2235_0800G307970H.fits[3]
ft950729_2235_0800G308070H.fits[3]
ft950729_2235_0800G308170M.fits[3]
ft950729_2235_0800G308270M.fits[3]
ft950729_2235_0800G308570L.fits[3]
ft950729_2235_0800G308670M.fits[3]
ft950729_2235_0800G308770M.fits[3]
ft950729_2235_0800G309070L.fits[3]
ft950729_2235_0800G309170H.fits[3]
ft950729_2235_0800G309270H.fits[3]
ft950729_2235_0800G309370H.fits[3]
ft950729_2235_0800G309470H.fits[3]
ft950729_2235_0800G309570L.fits[3]
ft950729_2235_0800G309670L.fits[3]
ft950729_2235_0800G309870M.fits[3]
ft950729_2235_0800G309970H.fits[3]
ft950729_2235_0800G310170H.fits[3]
ft950729_2235_0800G310370H.fits[3]
ft950729_2235_0800G310970H.fits[3]
ft950729_2235_0800G311070H.fits[3]
ft950729_2235_0800G311170H.fits[3]
ft950729_2235_0800G311270L.fits[3]
ft950729_2235_0800G311370L.fits[3]
ft950729_2235_0800G311570M.fits[3]
ft950729_2235_0800G311670M.fits[3]
ft950729_2235_0800G311770H.fits[3]
ft950729_2235_0800G311870H.fits[3]
ft950729_2235_0800G311970H.fits[3]
ft950729_2235_0800G312070H.fits[3]
ft950729_2235_0800G312170L.fits[3]
ft950729_2235_0800G312770M.fits[3]
ft950729_2235_0800G312870M.fits[3]
ft950729_2235_0800G312970H.fits[3]
ft950729_2235_0800G313070H.fits[3]
ft950729_2235_0800G313170H.fits[3]
ft950729_2235_0800G313270M.fits[3]
ft950729_2235_0800G313370M.fits[3]
ft950729_2235_0800G313470L.fits[3]
ft950729_2235_0800G313570L.fits[3]
ft950729_2235_0800G314170M.fits[3]
ft950729_2235_0800G314270M.fits[3]
ft950729_2235_0800G314370H.fits[3]
ft950729_2235_0800G314470H.fits[3]
ft950729_2235_0800G314570H.fits[3]
ft950729_2235_0800G314670H.fits[3]
ft950729_2235_0800G314770L.fits[3]
ft950729_2235_0800G315070M.fits[3]
ft950729_2235_0800G315170M.fits[3]
ft950729_2235_0800G315270H.fits[3]
ft950729_2235_0800G315370H.fits[3]
ft950729_2235_0800G315470H.fits[3]
ft950729_2235_0800G315570H.fits[3]
ft950729_2235_0800G315670H.fits[3]
ft950729_2235_0800G315770H.fits[3]
ft950729_2235_0800G316370H.fits[3]
ft950729_2235_0800G316470H.fits[3]
ft950729_2235_0800G316670H.fits[3]
ft950729_2235_0800G316770L.fits[3]
ft950729_2235_0800G316870M.fits[3]
ft950729_2235_0800G316970M.fits[3]
ft950729_2235_0800G317070M.fits[3]
ft950729_2235_0800G317170M.fits[3]
ft950729_2235_0800G317470M.fits[3]
ft950729_2235_0800G317570M.fits[3]
ft950729_2235_0800G317670H.fits[3]
ft950729_2235_0800G317770H.fits[3]
ft950729_2235_0800G317870H.fits[3]
ft950729_2235_0800G317970H.fits[3]
ft950729_2235_0800G318070L.fits[3]
ft950729_2235_0800G318170M.fits[3]
ft950729_2235_0800G318270M.fits[3]
ft950729_2235_0800G318370M.fits[3]
ft950729_2235_0800G318470M.fits[3]
ft950729_2235_0800G318570M.fits[3]
ft950729_2235_0800G318770M.fits[3]
ft950729_2235_0800G318870M.fits[3]
ft950729_2235_0800G318970H.fits[3]
ft950729_2235_0800G319070H.fits[3]
ft950729_2235_0800G319170H.fits[3]
ft950729_2235_0800G319270H.fits[3]
ft950729_2235_0800G319370M.fits[3]
ft950729_2235_0800G319470M.fits[3]
ft950729_2235_0800G319570H.fits[3]
ft950729_2235_0800G319670H.fits[3]
ft950729_2235_0800G319770H.fits[3]
ft950729_2235_0800G319870H.fits[3]
ft950729_2235_0800G319970M.fits[3]
ft950729_2235_0800G320070M.fits[3]
ft950729_2235_0800G320170H.fits[3]
ft950729_2235_0800G320270H.fits[3]
ft950729_2235_0800G320370H.fits[3]
ft950729_2235_0800G320470H.fits[3]
ft950729_2235_0800G320570M.fits[3]
ft950729_2235_0800G320670M.fits[3]
ft950729_2235_0800G320870H.fits[3]
ft950729_2235_0800G320970H.fits[3]
ft950729_2235_0800G321070H.fits[3]
ft950729_2235_0800G321170M.fits[3]
ft950729_2235_0800G321270M.fits[3]
ft950729_2235_0800G321370L.fits[3]
ft950729_2235_0800G321470L.fits[3]
ft950729_2235_0800G321570M.fits[3]
ft950729_2235_0800G321670H.fits[3]
ft950729_2235_0800G321770H.fits[3]
ft950729_2235_0800G321870H.fits[3]
ft950729_2235_0800G321970H.fits[3]
ft950729_2235_0800G322070H.fits[3]
ft950729_2235_0800G322170H.fits[3]
ft950729_2235_0800G322270H.fits[3]
ft950729_2235_0800G322370H.fits[3]
ft950729_2235_0800G322470M.fits[3]
ft950729_2235_0800G322570M.fits[3]
ft950729_2235_0800G322670L.fits[3]
ft950729_2235_0800G322770L.fits[3]
ft950729_2235_0800G322870M.fits[3]
ft950729_2235_0800G322970H.fits[3]
ft950729_2235_0800G323070H.fits[3]
ft950729_2235_0800G323170H.fits[3]
ft950729_2235_0800G323370H.fits[3]
ft950729_2235_0800G323470H.fits[3]
ft950729_2235_0800G323570H.fits[3]
ft950729_2235_0800G323670M.fits[3]
ft950729_2235_0800G323770M.fits[3]
ft950729_2235_0800G323870L.fits[3]
ft950729_2235_0800G323970M.fits[3]
ft950729_2235_0800G324070M.fits[3]
ft950729_2235_0800G324170M.fits[3]
ft950729_2235_0800G324270M.fits[3]
ft950729_2235_0800G324370L.fits[3]
ft950729_2235_0800G324570L.fits[3]
ft950729_2235_0800G324670L.fits[3]
ft950729_2235_0800G324770H.fits[3]
ft950729_2235_0800G324970H.fits[3]
ft950729_2235_0800G325070H.fits[3]
ft950729_2235_0800G325170M.fits[3]
ft950729_2235_0800G325270M.fits[3]
ft950729_2235_0800G325370M.fits[3]
ft950729_2235_0800G325870M.fits[3]
ft950729_2235_0800G325970M.fits[3]
ft950729_2235_0800G326070H.fits[3]
ft950729_2235_0800G326270H.fits[3]
ft950729_2235_0800G326370H.fits[3]
ft950729_2235_0800G326470H.fits[3]
ft950729_2235_0800G326870H.fits[3]
ft950729_2235_0800G326970H.fits[3]
ft950729_2235_0800G327070H.fits[3]
ft950729_2235_0800G327170M.fits[3]
ft950729_2235_0800G327270M.fits[3]
ft950729_2235_0800G327370L.fits[3]
ft950729_2235_0800G327470L.fits[3]
ft950729_2235_0800G328270H.fits[3]
ft950729_2235_0800G328370H.fits[3]
ft950729_2235_0800G328470M.fits[3]
ft950729_2235_0800G328570M.fits[3]
ft950729_2235_0800G328670L.fits[3]
ft950729_2235_0800G328770L.fits[3]
ft950729_2235_0800G329370M.fits[3]
ft950729_2235_0800G329470M.fits[3]
ft950729_2235_0800G329570H.fits[3]
ft950729_2235_0800G329770H.fits[3]
ft950729_2235_0800G329870M.fits[3]
ft950729_2235_0800G329970M.fits[3]
ft950729_2235_0800G330070L.fits[3]
ft950729_2235_0800G330170L.fits[3]
ft950729_2235_0800G330770M.fits[3]
ft950729_2235_0800G330870M.fits[3]
ft950729_2235_0800G330970H.fits[3]
ft950729_2235_0800G331070H.fits[3]
ft950729_2235_0800G331170H.fits[3]
ft950729_2235_0800G331270H.fits[3]
ft950729_2235_0800G331370M.fits[3]
ft950729_2235_0800G331470M.fits[3]
ft950729_2235_0800G331570L.fits[3]
ft950729_2235_0800G331670L.fits[3]
ft950729_2235_0800G332370H.fits[3]
ft950729_2235_0800G332470H.fits[3]
ft950729_2235_0800G332570H.fits[3]
ft950729_2235_0800G332670H.fits[3]
ft950729_2235_0800G333070H.fits[3]
ft950729_2235_0800G333170H.fits[3]
ft950729_2235_0800G333270H.fits[3]
ft950729_2235_0800G333470H.fits[3]
ft950729_2235_0800G333570M.fits[3]
ft950729_2235_0800G333670M.fits[3]
ft950729_2235_0800G333770L.fits[3]
ft950729_2235_0800G333870L.fits[3]
ft950729_2235_0800G333970M.fits[3]
ft950729_2235_0800G334070M.fits[3]
ft950729_2235_0800G334770H.fits[3]
ft950729_2235_0800G334870H.fits[3]
ft950729_2235_0800G334970M.fits[3]
ft950729_2235_0800G335070M.fits[3]
ft950729_2235_0800G335170L.fits[3]
ft950729_2235_0800G335270L.fits[3]
ft950729_2235_0800G335370M.fits[3]
ft950729_2235_0800G335470H.fits[3]
ft950729_2235_0800G335570H.fits[3]
ft950729_2235_0800G335670H.fits[3]
ft950729_2235_0800G335770H.fits[3]
ft950729_2235_0800G335870M.fits[3]
ft950729_2235_0800G335970M.fits[3]
ft950729_2235_0800G336070L.fits[3]
ft950729_2235_0800G336170M.fits[3]
ft950729_2235_0800G336370H.fits[3]
ft950729_2235_0800G336470H.fits[3]
ft950729_2235_0800G336570H.fits[3]
ft950729_2235_0800G336670M.fits[3]
ft950729_2235_0800G336770M.fits[3]
ft950729_2235_0800G336870M.fits[3]
ft950729_2235_0800G336970M.fits[3]
ft950729_2235_0800G337070M.fits[3]

Merging event files from frfread ( 21:24:26 )

-> Collecting GIS2 event files by mode
-> Standard Error Output From STOOL gissortcode:
GISSORTCODE:LO:Start program
GISSORTCODE:LO:End program
-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program
GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 2
GISSORTSPLIT:LO:g200370h.prelist merge count = 3 photon cnt = 7
GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g201170h.prelist merge count = 2 photon cnt = 10
GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 9
GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g201470h.prelist merge count = 45 photon cnt = 99435
GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g201670h.prelist merge count = 14 photon cnt = 57
GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g201870h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g201970h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g202070h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g202170h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g202270h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g202370h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g202470h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g202570h.prelist merge count = 1 photon cnt = 12
GISSORTSPLIT:LO:g202670h.prelist merge count = 1 photon cnt = 8
GISSORTSPLIT:LO:g202770h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g202870h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g202970h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g203070h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g203170h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g203270h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g203370h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g203470h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g203570h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g203670h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g203770h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g203870h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g203970h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g204070h.prelist merge count = 1 photon cnt = 8
GISSORTSPLIT:LO:g204170h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g204270h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g204370h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g204470h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g204570h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g204670h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g204770h.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g204870h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g204970h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g205070h.prelist merge count = 4 photon cnt = 35
GISSORTSPLIT:LO:g205170h.prelist merge count = 3 photon cnt = 9
GISSORTSPLIT:LO:g205270h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g205370h.prelist merge count = 2 photon cnt = 1508
GISSORTSPLIT:LO:g205470h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g205570h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g205670h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g205770h.prelist merge count = 1 photon cnt = 3723
GISSORTSPLIT:LO:g200170l.prelist merge count = 4 photon cnt = 62
GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g200370l.prelist merge count = 1 photon cnt = 18
GISSORTSPLIT:LO:g200470l.prelist merge count = 3 photon cnt = 157
GISSORTSPLIT:LO:g200570l.prelist merge count = 1 photon cnt = 44
GISSORTSPLIT:LO:g200670l.prelist merge count = 27 photon cnt = 19133
GISSORTSPLIT:LO:g200770l.prelist merge count = 16 photon cnt = 1422
GISSORTSPLIT:LO:g200170m.prelist merge count = 5 photon cnt = 25
GISSORTSPLIT:LO:g200270m.prelist merge count = 10 photon cnt = 151
GISSORTSPLIT:LO:g200370m.prelist merge count = 1 photon cnt = 58
GISSORTSPLIT:LO:g200470m.prelist merge count = 51 photon cnt = 80521
GISSORTSPLIT:LO:g200570m.prelist merge count = 23 photon cnt = 782
GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 9
GISSORTSPLIT:LO:g200870m.prelist merge count = 1 photon cnt = 22
GISSORTSPLIT:LO:g200970m.prelist merge count = 1 photon cnt = 18
GISSORTSPLIT:LO:g201070m.prelist merge count = 1 photon cnt = 16
GISSORTSPLIT:LO:g201170m.prelist merge count = 1 photon cnt = 16
GISSORTSPLIT:LO:g201270m.prelist merge count = 1 photon cnt = 18
GISSORTSPLIT:LO:g201370m.prelist merge count = 1 photon cnt = 16
GISSORTSPLIT:LO:g201470m.prelist merge count = 1 photon cnt = 13
GISSORTSPLIT:LO:g201570m.prelist merge count = 1 photon cnt = 14
GISSORTSPLIT:LO:g201670m.prelist merge count = 1 photon cnt = 30
GISSORTSPLIT:LO:g201770m.prelist merge count = 1 photon cnt = 35
GISSORTSPLIT:LO:g201870m.prelist merge count = 1 photon cnt = 26
GISSORTSPLIT:LO:g201970m.prelist merge count = 1 photon cnt = 37
GISSORTSPLIT:LO:g202070m.prelist merge count = 1 photon cnt = 24
GISSORTSPLIT:LO:g202170m.prelist merge count = 1 photon cnt = 28
GISSORTSPLIT:LO:Total filenames split = 283
GISSORTSPLIT:LO:Total split file cnt = 85
GISSORTSPLIT:LO:End program
-> Creating ad63007000g200170h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  45  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G202170H.fits 
 2 -- ft950729_2235_0800G203170H.fits 
 3 -- ft950729_2235_0800G203670H.fits 
 4 -- ft950729_2235_0800G204370H.fits 
 5 -- ft950729_2235_0800G205170H.fits 
 6 -- ft950729_2235_0800G205370H.fits 
 7 -- ft950729_2235_0800G205870H.fits 
 8 -- ft950729_2235_0800G206570H.fits 
 9 -- ft950729_2235_0800G206770H.fits 
 10 -- ft950729_2235_0800G206970H.fits 
 11 -- ft950729_2235_0800G207270H.fits 
 12 -- ft950729_2235_0800G207470H.fits 
 13 -- ft950729_2235_0800G209270H.fits 
 14 -- ft950729_2235_0800G209770H.fits 
 15 -- ft950729_2235_0800G209970H.fits 
 16 -- ft950729_2235_0800G210970H.fits 
 17 -- ft950729_2235_0800G211870H.fits 
 18 -- ft950729_2235_0800G212870H.fits 
 19 -- ft950729_2235_0800G214370H.fits 
 20 -- ft950729_2235_0800G215270H.fits 
 21 -- ft950729_2235_0800G216270H.fits 
 22 -- ft950729_2235_0800G217770H.fits 
 23 -- ft950729_2235_0800G219070H.fits 
 24 -- ft950729_2235_0800G219670H.fits 
 25 -- ft950729_2235_0800G220270H.fits 
 26 -- ft950729_2235_0800G220870H.fits 
 27 -- ft950729_2235_0800G221770H.fits 
 28 -- ft950729_2235_0800G221970H.fits 
 29 -- ft950729_2235_0800G222370H.fits 
 30 -- ft950729_2235_0800G222970H.fits 
 31 -- ft950729_2235_0800G223170H.fits 
 32 -- ft950729_2235_0800G223370H.fits 
 33 -- ft950729_2235_0800G224870H.fits 
 34 -- ft950729_2235_0800G225870H.fits 
 35 -- ft950729_2235_0800G226070H.fits 
 36 -- ft950729_2235_0800G226770H.fits 
 37 -- ft950729_2235_0800G228070H.fits 
 38 -- ft950729_2235_0800G229270H.fits 
 39 -- ft950729_2235_0800G229470H.fits 
 40 -- ft950729_2235_0800G230970H.fits 
 41 -- ft950729_2235_0800G232270H.fits 
 42 -- ft950729_2235_0800G233070H.fits 
 43 -- ft950729_2235_0800G234670H.fits 
 44 -- ft950729_2235_0800G235570H.fits 
 45 -- ft950729_2235_0800G236370H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G202170H.fits 
 2 -- ft950729_2235_0800G203170H.fits 
 3 -- ft950729_2235_0800G203670H.fits 
 4 -- ft950729_2235_0800G204370H.fits 
 5 -- ft950729_2235_0800G205170H.fits 
 6 -- ft950729_2235_0800G205370H.fits 
 7 -- ft950729_2235_0800G205870H.fits 
 8 -- ft950729_2235_0800G206570H.fits 
 9 -- ft950729_2235_0800G206770H.fits 
 10 -- ft950729_2235_0800G206970H.fits 
 11 -- ft950729_2235_0800G207270H.fits 
 12 -- ft950729_2235_0800G207470H.fits 
 13 -- ft950729_2235_0800G209270H.fits 
 14 -- ft950729_2235_0800G209770H.fits 
 15 -- ft950729_2235_0800G209970H.fits 
 16 -- ft950729_2235_0800G210970H.fits 
 17 -- ft950729_2235_0800G211870H.fits 
 18 -- ft950729_2235_0800G212870H.fits 
 19 -- ft950729_2235_0800G214370H.fits 
 20 -- ft950729_2235_0800G215270H.fits 
 21 -- ft950729_2235_0800G216270H.fits 
 22 -- ft950729_2235_0800G217770H.fits 
 23 -- ft950729_2235_0800G219070H.fits 
 24 -- ft950729_2235_0800G219670H.fits 
 25 -- ft950729_2235_0800G220270H.fits 
 26 -- ft950729_2235_0800G220870H.fits 
 27 -- ft950729_2235_0800G221770H.fits 
 28 -- ft950729_2235_0800G221970H.fits 
 29 -- ft950729_2235_0800G222370H.fits 
 30 -- ft950729_2235_0800G222970H.fits 
 31 -- ft950729_2235_0800G223170H.fits 
 32 -- ft950729_2235_0800G223370H.fits 
 33 -- ft950729_2235_0800G224870H.fits 
 34 -- ft950729_2235_0800G225870H.fits 
 35 -- ft950729_2235_0800G226070H.fits 
 36 -- ft950729_2235_0800G226770H.fits 
 37 -- ft950729_2235_0800G228070H.fits 
 38 -- ft950729_2235_0800G229270H.fits 
 39 -- ft950729_2235_0800G229470H.fits 
 40 -- ft950729_2235_0800G230970H.fits 
 41 -- ft950729_2235_0800G232270H.fits 
 42 -- ft950729_2235_0800G233070H.fits 
 43 -- ft950729_2235_0800G234670H.fits 
 44 -- ft950729_2235_0800G235570H.fits 
 45 -- ft950729_2235_0800G236370H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g200270m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  51  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G200170M.fits 
 2 -- ft950729_2235_0800G200970M.fits 
 3 -- ft950729_2235_0800G201670M.fits 
 4 -- ft950729_2235_0800G202070M.fits 
 5 -- ft950729_2235_0800G202270M.fits 
 6 -- ft950729_2235_0800G203070M.fits 
 7 -- ft950729_2235_0800G203270M.fits 
 8 -- ft950729_2235_0800G203570M.fits 
 9 -- ft950729_2235_0800G203770M.fits 
 10 -- ft950729_2235_0800G204470M.fits 
 11 -- ft950729_2235_0800G205070M.fits 
 12 -- ft950729_2235_0800G205470M.fits 
 13 -- ft950729_2235_0800G205770M.fits 
 14 -- ft950729_2235_0800G206470M.fits 
 15 -- ft950729_2235_0800G207770M.fits 
 16 -- ft950729_2235_0800G208270M.fits 
 17 -- ft950729_2235_0800G208470M.fits 
 18 -- ft950729_2235_0800G209670M.fits 
 19 -- ft950729_2235_0800G211470M.fits 
 20 -- ft950729_2235_0800G212670M.fits 
 21 -- ft950729_2235_0800G213070M.fits 
 22 -- ft950729_2235_0800G213970M.fits 
 23 -- ft950729_2235_0800G214870M.fits 
 24 -- ft950729_2235_0800G216970M.fits 
 25 -- ft950729_2235_0800G217370M.fits 
 26 -- ft950729_2235_0800G218270M.fits 
 27 -- ft950729_2235_0800G218670M.fits 
 28 -- ft950729_2235_0800G219270M.fits 
 29 -- ft950729_2235_0800G219870M.fits 
 30 -- ft950729_2235_0800G220470M.fits 
 31 -- ft950729_2235_0800G221070M.fits 
 32 -- ft950729_2235_0800G221370M.fits 
 33 -- ft950729_2235_0800G222570M.fits 
 34 -- ft950729_2235_0800G222870M.fits 
 35 -- ft950729_2235_0800G223570M.fits 
 36 -- ft950729_2235_0800G224070M.fits 
 37 -- ft950729_2235_0800G225070M.fits 
 38 -- ft950729_2235_0800G225770M.fits 
 39 -- ft950729_2235_0800G226970M.fits 
 40 -- ft950729_2235_0800G228270M.fits 
 41 -- ft950729_2235_0800G229170M.fits 
 42 -- ft950729_2235_0800G229670M.fits 
 43 -- ft950729_2235_0800G230570M.fits 
 44 -- ft950729_2235_0800G231170M.fits 
 45 -- ft950729_2235_0800G233470M.fits 
 46 -- ft950729_2235_0800G233770M.fits 
 47 -- ft950729_2235_0800G234870M.fits 
 48 -- ft950729_2235_0800G235170M.fits 
 49 -- ft950729_2235_0800G235770M.fits 
 50 -- ft950729_2235_0800G235970M.fits 
 51 -- ft950729_2235_0800G236470M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G200170M.fits 
 2 -- ft950729_2235_0800G200970M.fits 
 3 -- ft950729_2235_0800G201670M.fits 
 4 -- ft950729_2235_0800G202070M.fits 
 5 -- ft950729_2235_0800G202270M.fits 
 6 -- ft950729_2235_0800G203070M.fits 
 7 -- ft950729_2235_0800G203270M.fits 
 8 -- ft950729_2235_0800G203570M.fits 
 9 -- ft950729_2235_0800G203770M.fits 
 10 -- ft950729_2235_0800G204470M.fits 
 11 -- ft950729_2235_0800G205070M.fits 
 12 -- ft950729_2235_0800G205470M.fits 
 13 -- ft950729_2235_0800G205770M.fits 
 14 -- ft950729_2235_0800G206470M.fits 
 15 -- ft950729_2235_0800G207770M.fits 
 16 -- ft950729_2235_0800G208270M.fits 
 17 -- ft950729_2235_0800G208470M.fits 
 18 -- ft950729_2235_0800G209670M.fits 
 19 -- ft950729_2235_0800G211470M.fits 
 20 -- ft950729_2235_0800G212670M.fits 
 21 -- ft950729_2235_0800G213070M.fits 
 22 -- ft950729_2235_0800G213970M.fits 
 23 -- ft950729_2235_0800G214870M.fits 
 24 -- ft950729_2235_0800G216970M.fits 
 25 -- ft950729_2235_0800G217370M.fits 
 26 -- ft950729_2235_0800G218270M.fits 
 27 -- ft950729_2235_0800G218670M.fits 
 28 -- ft950729_2235_0800G219270M.fits 
 29 -- ft950729_2235_0800G219870M.fits 
 30 -- ft950729_2235_0800G220470M.fits 
 31 -- ft950729_2235_0800G221070M.fits 
 32 -- ft950729_2235_0800G221370M.fits 
 33 -- ft950729_2235_0800G222570M.fits 
 34 -- ft950729_2235_0800G222870M.fits 
 35 -- ft950729_2235_0800G223570M.fits 
 36 -- ft950729_2235_0800G224070M.fits 
 37 -- ft950729_2235_0800G225070M.fits 
 38 -- ft950729_2235_0800G225770M.fits 
 39 -- ft950729_2235_0800G226970M.fits 
 40 -- ft950729_2235_0800G228270M.fits 
 41 -- ft950729_2235_0800G229170M.fits 
 42 -- ft950729_2235_0800G229670M.fits 
 43 -- ft950729_2235_0800G230570M.fits 
 44 -- ft950729_2235_0800G231170M.fits 
 45 -- ft950729_2235_0800G233470M.fits 
 46 -- ft950729_2235_0800G233770M.fits 
 47 -- ft950729_2235_0800G234870M.fits 
 48 -- ft950729_2235_0800G235170M.fits 
 49 -- ft950729_2235_0800G235770M.fits 
 50 -- ft950729_2235_0800G235970M.fits 
 51 -- ft950729_2235_0800G236470M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g200370l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  27  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G200270L.fits 
 2 -- ft950729_2235_0800G200570L.fits 
 3 -- ft950729_2235_0800G201070L.fits 
 4 -- ft950729_2235_0800G201770L.fits 
 5 -- ft950729_2235_0800G202470L.fits 
 6 -- ft950729_2235_0800G202670L.fits 
 7 -- ft950729_2235_0800G203470L.fits 
 8 -- ft950729_2235_0800G203970L.fits 
 9 -- ft950729_2235_0800G204670L.fits 
 10 -- ft950729_2235_0800G205670L.fits 
 11 -- ft950729_2235_0800G206070L.fits 
 12 -- ft950729_2235_0800G211070L.fits 
 13 -- ft950729_2235_0800G211970L.fits 
 14 -- ft950729_2235_0800G213270L.fits 
 15 -- ft950729_2235_0800G214470L.fits 
 16 -- ft950729_2235_0800G216570L.fits 
 17 -- ft950729_2235_0800G217870L.fits 
 18 -- ft950729_2235_0800G221270L.fits 
 19 -- ft950729_2235_0800G222770L.fits 
 20 -- ft950729_2235_0800G224470L.fits 
 21 -- ft950729_2235_0800G227170L.fits 
 22 -- ft950729_2235_0800G228470L.fits 
 23 -- ft950729_2235_0800G229870L.fits 
 24 -- ft950729_2235_0800G231370L.fits 
 25 -- ft950729_2235_0800G233670L.fits 
 26 -- ft950729_2235_0800G235070L.fits 
 27 -- ft950729_2235_0800G235870L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G200270L.fits 
 2 -- ft950729_2235_0800G200570L.fits 
 3 -- ft950729_2235_0800G201070L.fits 
 4 -- ft950729_2235_0800G201770L.fits 
 5 -- ft950729_2235_0800G202470L.fits 
 6 -- ft950729_2235_0800G202670L.fits 
 7 -- ft950729_2235_0800G203470L.fits 
 8 -- ft950729_2235_0800G203970L.fits 
 9 -- ft950729_2235_0800G204670L.fits 
 10 -- ft950729_2235_0800G205670L.fits 
 11 -- ft950729_2235_0800G206070L.fits 
 12 -- ft950729_2235_0800G211070L.fits 
 13 -- ft950729_2235_0800G211970L.fits 
 14 -- ft950729_2235_0800G213270L.fits 
 15 -- ft950729_2235_0800G214470L.fits 
 16 -- ft950729_2235_0800G216570L.fits 
 17 -- ft950729_2235_0800G217870L.fits 
 18 -- ft950729_2235_0800G221270L.fits 
 19 -- ft950729_2235_0800G222770L.fits 
 20 -- ft950729_2235_0800G224470L.fits 
 21 -- ft950729_2235_0800G227170L.fits 
 22 -- ft950729_2235_0800G228470L.fits 
 23 -- ft950729_2235_0800G229870L.fits 
 24 -- ft950729_2235_0800G231370L.fits 
 25 -- ft950729_2235_0800G233670L.fits 
 26 -- ft950729_2235_0800G235070L.fits 
 27 -- ft950729_2235_0800G235870L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Checking ft950729_2235_0800G207670H.fits

E1 in combine: RAWXBINS=256 and RAWYBINS=4 in ft950729_2235_0800G207670H.fits

-> Ignoring the following files containing 000003723 events
ft950729_2235_0800G207670H.fits
-> Creating ad63007000g200470h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G216470H.fits 
 2 -- ft950729_2235_0800G233270H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G216470H.fits 
 2 -- ft950729_2235_0800G233270H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g200570l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  16  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G202370L.fits 
 2 -- ft950729_2235_0800G203370L.fits 
 3 -- ft950729_2235_0800G203870L.fits 
 4 -- ft950729_2235_0800G204570L.fits 
 5 -- ft950729_2235_0800G205570L.fits 
 6 -- ft950729_2235_0800G205970L.fits 
 7 -- ft950729_2235_0800G209370L.fits 
 8 -- ft950729_2235_0800G213170L.fits 
 9 -- ft950729_2235_0800G221170L.fits 
 10 -- ft950729_2235_0800G222670L.fits 
 11 -- ft950729_2235_0800G227070L.fits 
 12 -- ft950729_2235_0800G228370L.fits 
 13 -- ft950729_2235_0800G229770L.fits 
 14 -- ft950729_2235_0800G231270L.fits 
 15 -- ft950729_2235_0800G233570L.fits 
 16 -- ft950729_2235_0800G234970L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G202370L.fits 
 2 -- ft950729_2235_0800G203370L.fits 
 3 -- ft950729_2235_0800G203870L.fits 
 4 -- ft950729_2235_0800G204570L.fits 
 5 -- ft950729_2235_0800G205570L.fits 
 6 -- ft950729_2235_0800G205970L.fits 
 7 -- ft950729_2235_0800G209370L.fits 
 8 -- ft950729_2235_0800G213170L.fits 
 9 -- ft950729_2235_0800G221170L.fits 
 10 -- ft950729_2235_0800G222670L.fits 
 11 -- ft950729_2235_0800G227070L.fits 
 12 -- ft950729_2235_0800G228370L.fits 
 13 -- ft950729_2235_0800G229770L.fits 
 14 -- ft950729_2235_0800G231270L.fits 
 15 -- ft950729_2235_0800G233570L.fits 
 16 -- ft950729_2235_0800G234970L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g200670m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  23  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G200870M.fits 
 2 -- ft950729_2235_0800G201570M.fits 
 3 -- ft950729_2235_0800G202970M.fits 
 4 -- ft950729_2235_0800G204970M.fits 
 5 -- ft950729_2235_0800G206370M.fits 
 6 -- ft950729_2235_0800G212970M.fits 
 7 -- ft950729_2235_0800G216870M.fits 
 8 -- ft950729_2235_0800G218170M.fits 
 9 -- ft950729_2235_0800G219170M.fits 
 10 -- ft950729_2235_0800G219770M.fits 
 11 -- ft950729_2235_0800G220370M.fits 
 12 -- ft950729_2235_0800G220970M.fits 
 13 -- ft950729_2235_0800G222470M.fits 
 14 -- ft950729_2235_0800G223470M.fits 
 15 -- ft950729_2235_0800G223970M.fits 
 16 -- ft950729_2235_0800G224970M.fits 
 17 -- ft950729_2235_0800G226870M.fits 
 18 -- ft950729_2235_0800G228170M.fits 
 19 -- ft950729_2235_0800G229570M.fits 
 20 -- ft950729_2235_0800G231070M.fits 
 21 -- ft950729_2235_0800G233370M.fits 
 22 -- ft950729_2235_0800G234770M.fits 
 23 -- ft950729_2235_0800G235670M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G200870M.fits 
 2 -- ft950729_2235_0800G201570M.fits 
 3 -- ft950729_2235_0800G202970M.fits 
 4 -- ft950729_2235_0800G204970M.fits 
 5 -- ft950729_2235_0800G206370M.fits 
 6 -- ft950729_2235_0800G212970M.fits 
 7 -- ft950729_2235_0800G216870M.fits 
 8 -- ft950729_2235_0800G218170M.fits 
 9 -- ft950729_2235_0800G219170M.fits 
 10 -- ft950729_2235_0800G219770M.fits 
 11 -- ft950729_2235_0800G220370M.fits 
 12 -- ft950729_2235_0800G220970M.fits 
 13 -- ft950729_2235_0800G222470M.fits 
 14 -- ft950729_2235_0800G223470M.fits 
 15 -- ft950729_2235_0800G223970M.fits 
 16 -- ft950729_2235_0800G224970M.fits 
 17 -- ft950729_2235_0800G226870M.fits 
 18 -- ft950729_2235_0800G228170M.fits 
 19 -- ft950729_2235_0800G229570M.fits 
 20 -- ft950729_2235_0800G231070M.fits 
 21 -- ft950729_2235_0800G233370M.fits 
 22 -- ft950729_2235_0800G234770M.fits 
 23 -- ft950729_2235_0800G235670M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Ignoring the following files containing 000000157 events
ft950729_2235_0800G201270L.fits
ft950729_2235_0800G208170L.fits
ft950729_2235_0800G208870L.fits
-> Ignoring the following files containing 000000151 events
ft950729_2235_0800G201970M.fits
ft950729_2235_0800G211370M.fits
ft950729_2235_0800G212570M.fits
ft950729_2235_0800G213870M.fits
ft950729_2235_0800G214770M.fits
ft950729_2235_0800G217270M.fits
ft950729_2235_0800G218570M.fits
ft950729_2235_0800G225670M.fits
ft950729_2235_0800G229070M.fits
ft950729_2235_0800G230470M.fits
-> Ignoring the following files containing 000000062 events
ft950729_2235_0800G200470L.fits
ft950729_2235_0800G202570L.fits
ft950729_2235_0800G209470L.fits
ft950729_2235_0800G223670L.fits
-> Ignoring the following files containing 000000058 events
ft950729_2235_0800G208370M.fits
-> Ignoring the following files containing 000000057 events
ft950729_2235_0800G204270H.fits
ft950729_2235_0800G209170H.fits
ft950729_2235_0800G211770H.fits
ft950729_2235_0800G214270H.fits
ft950729_2235_0800G215170H.fits
ft950729_2235_0800G217670H.fits
ft950729_2235_0800G218970H.fits
ft950729_2235_0800G219570H.fits
ft950729_2235_0800G220170H.fits
ft950729_2235_0800G221670H.fits
ft950729_2235_0800G224770H.fits
ft950729_2235_0800G230870H.fits
ft950729_2235_0800G235470H.fits
ft950729_2235_0800G236270H.fits
-> Ignoring the following files containing 000000044 events
ft950729_2235_0800G224370L.fits
-> Ignoring the following files containing 000000037 events
ft950729_2235_0800G200770M.fits
-> Ignoring the following files containing 000000035 events
ft950729_2235_0800G210770H.fits
ft950729_2235_0800G216070H.fits
ft950729_2235_0800G226670H.fits
ft950729_2235_0800G232870H.fits
-> Ignoring the following files containing 000000035 events
ft950729_2235_0800G201470M.fits
-> Ignoring the following files containing 000000030 events
ft950729_2235_0800G201370M.fits
-> Ignoring the following files containing 000000028 events
ft950729_2235_0800G202870M.fits
-> Ignoring the following files containing 000000026 events
ft950729_2235_0800G200670M.fits
-> Ignoring the following files containing 000000025 events
ft950729_2235_0800G207870M.fits
ft950729_2235_0800G208570M.fits
ft950729_2235_0800G218370M.fits
ft950729_2235_0800G225170M.fits
ft950729_2235_0800G233870M.fits
-> Ignoring the following files containing 000000024 events
ft950729_2235_0800G202770M.fits
-> Ignoring the following files containing 000000022 events
ft950729_2235_0800G206170M.fits
-> Ignoring the following files containing 000000018 events
ft950729_2235_0800G223770M.fits
-> Ignoring the following files containing 000000018 events
ft950729_2235_0800G206270M.fits
-> Ignoring the following files containing 000000018 events
ft950729_2235_0800G200370L.fits
-> Ignoring the following files containing 000000016 events
ft950729_2235_0800G223870M.fits
-> Ignoring the following files containing 000000016 events
ft950729_2235_0800G216770M.fits
-> Ignoring the following files containing 000000016 events
ft950729_2235_0800G216670M.fits
-> Ignoring the following files containing 000000014 events
ft950729_2235_0800G204870M.fits
-> Ignoring the following files containing 000000013 events
ft950729_2235_0800G204770M.fits
-> Ignoring the following files containing 000000012 events
ft950729_2235_0800G235270H.fits
-> Ignoring the following files containing 000000010 events
ft950729_2235_0800G222070H.fits
ft950729_2235_0800G222270H.fits
-> Ignoring the following files containing 000000009 events
ft950729_2235_0800G210870H.fits
ft950729_2235_0800G216170H.fits
ft950729_2235_0800G232970H.fits
-> Ignoring the following files containing 000000009 events
ft950729_2235_0800G206870H.fits
-> Ignoring the following files containing 000000009 events
ft950729_2235_0800G218070M.fits
-> Ignoring the following files containing 000000008 events
ft950729_2235_0800G218770H.fits
-> Ignoring the following files containing 000000008 events
ft950729_2235_0800G235370H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G207570H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G207370H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G227970H.fits
ft950729_2235_0800G232170H.fits
ft950729_2235_0800G234570H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G214170H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G205270H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G206670H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G215970H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G223270H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G214970H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G211670H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G212770H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G207070H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G232770H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G221470H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G217470H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G208970H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G230770H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G219470H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G219370H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G226170H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G210070H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G217970M.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G207170H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G226570H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G220070H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G218870H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G215070H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G217570H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G204170H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G236170H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G236070H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G232370H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G210570H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G210670H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G224670H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G224570H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G219970H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G221570H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G211570H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G204070H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G230670H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G220670H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G220570H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G232070H.fits
ft950729_2235_0800G234470H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G215870H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G214070H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G222170H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G224170L.fits
-> Collecting GIS3 event files by mode
-> Standard Error Output From STOOL gissortcode:
GISSORTCODE:LO:Start program
GISSORTCODE:LO:End program
-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program
GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 7
GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 14
GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 12
GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 9
GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g301470h.prelist merge count = 50 photon cnt = 102159
GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 10
GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g301870h.prelist merge count = 15 photon cnt = 51
GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g302070h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g302170h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g302270h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g302370h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g302470h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g302570h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g302670h.prelist merge count = 1 photon cnt = 9
GISSORTSPLIT:LO:g302770h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g302870h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g302970h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g303070h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g303170h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g303270h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g303370h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g303470h.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g303570h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g303670h.prelist merge count = 1 photon cnt = 8
GISSORTSPLIT:LO:g303770h.prelist merge count = 1 photon cnt = 10
GISSORTSPLIT:LO:g303870h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g303970h.prelist merge count = 1 photon cnt = 11
GISSORTSPLIT:LO:g304070h.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g304170h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g304270h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g304370h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g304470h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g304570h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g304670h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g304770h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g304870h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g304970h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g305070h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g305170h.prelist merge count = 4 photon cnt = 63
GISSORTSPLIT:LO:g305270h.prelist merge count = 2 photon cnt = 1558
GISSORTSPLIT:LO:g305370h.prelist merge count = 1 photon cnt = 6
GISSORTSPLIT:LO:g305470h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g305570h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g305670h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g300170l.prelist merge count = 5 photon cnt = 51
GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g300370l.prelist merge count = 1 photon cnt = 12
GISSORTSPLIT:LO:g300470l.prelist merge count = 3 photon cnt = 124
GISSORTSPLIT:LO:g300570l.prelist merge count = 1 photon cnt = 50
GISSORTSPLIT:LO:g300670l.prelist merge count = 27 photon cnt = 17963
GISSORTSPLIT:LO:g300770l.prelist merge count = 16 photon cnt = 1329
GISSORTSPLIT:LO:g300170m.prelist merge count = 5 photon cnt = 20
GISSORTSPLIT:LO:g300270m.prelist merge count = 10 photon cnt = 114
GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 52
GISSORTSPLIT:LO:g300470m.prelist merge count = 52 photon cnt = 78760
GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 15
GISSORTSPLIT:LO:g300670m.prelist merge count = 23 photon cnt = 850
GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 11
GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 12
GISSORTSPLIT:LO:g300970m.prelist merge count = 1 photon cnt = 13
GISSORTSPLIT:LO:g301070m.prelist merge count = 1 photon cnt = 12
GISSORTSPLIT:LO:g301170m.prelist merge count = 1 photon cnt = 10
GISSORTSPLIT:LO:g301270m.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g301370m.prelist merge count = 1 photon cnt = 41
GISSORTSPLIT:LO:g301470m.prelist merge count = 1 photon cnt = 35
GISSORTSPLIT:LO:g301570m.prelist merge count = 1 photon cnt = 10
GISSORTSPLIT:LO:g301670m.prelist merge count = 1 photon cnt = 5
GISSORTSPLIT:LO:g301770m.prelist merge count = 1 photon cnt = 22
GISSORTSPLIT:LO:g301870m.prelist merge count = 1 photon cnt = 15
GISSORTSPLIT:LO:g301970m.prelist merge count = 1 photon cnt = 33
GISSORTSPLIT:LO:g302070m.prelist merge count = 1 photon cnt = 37
GISSORTSPLIT:LO:g302170m.prelist merge count = 1 photon cnt = 36
GISSORTSPLIT:LO:g302270m.prelist merge count = 1 photon cnt = 27
GISSORTSPLIT:LO:Total filenames split = 287
GISSORTSPLIT:LO:Total split file cnt = 85
GISSORTSPLIT:LO:End program
-> Creating ad63007000g300170h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  50  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G302170H.fits 
 2 -- ft950729_2235_0800G303170H.fits 
 3 -- ft950729_2235_0800G303670H.fits 
 4 -- ft950729_2235_0800G304370H.fits 
 5 -- ft950729_2235_0800G305170H.fits 
 6 -- ft950729_2235_0800G305370H.fits 
 7 -- ft950729_2235_0800G305870H.fits 
 8 -- ft950729_2235_0800G306070H.fits 
 9 -- ft950729_2235_0800G306770H.fits 
 10 -- ft950729_2235_0800G306970H.fits 
 11 -- ft950729_2235_0800G307170H.fits 
 12 -- ft950729_2235_0800G307370H.fits 
 13 -- ft950729_2235_0800G307570H.fits 
 14 -- ft950729_2235_0800G307770H.fits 
 15 -- ft950729_2235_0800G308070H.fits 
 16 -- ft950729_2235_0800G309470H.fits 
 17 -- ft950729_2235_0800G309970H.fits 
 18 -- ft950729_2235_0800G310170H.fits 
 19 -- ft950729_2235_0800G311170H.fits 
 20 -- ft950729_2235_0800G312070H.fits 
 21 -- ft950729_2235_0800G312970H.fits 
 22 -- ft950729_2235_0800G313170H.fits 
 23 -- ft950729_2235_0800G314670H.fits 
 24 -- ft950729_2235_0800G315570H.fits 
 25 -- ft950729_2235_0800G316470H.fits 
 26 -- ft950729_2235_0800G317970H.fits 
 27 -- ft950729_2235_0800G319270H.fits 
 28 -- ft950729_2235_0800G319870H.fits 
 29 -- ft950729_2235_0800G320470H.fits 
 30 -- ft950729_2235_0800G321070H.fits 
 31 -- ft950729_2235_0800G321970H.fits 
 32 -- ft950729_2235_0800G322170H.fits 
 33 -- ft950729_2235_0800G322370H.fits 
 34 -- ft950729_2235_0800G322970H.fits 
 35 -- ft950729_2235_0800G323170H.fits 
 36 -- ft950729_2235_0800G323370H.fits 
 37 -- ft950729_2235_0800G323570H.fits 
 38 -- ft950729_2235_0800G325070H.fits 
 39 -- ft950729_2235_0800G326070H.fits 
 40 -- ft950729_2235_0800G326270H.fits 
 41 -- ft950729_2235_0800G327070H.fits 
 42 -- ft950729_2235_0800G328370H.fits 
 43 -- ft950729_2235_0800G329570H.fits 
 44 -- ft950729_2235_0800G329770H.fits 
 45 -- ft950729_2235_0800G331270H.fits 
 46 -- ft950729_2235_0800G332570H.fits 
 47 -- ft950729_2235_0800G333270H.fits 
 48 -- ft950729_2235_0800G334870H.fits 
 49 -- ft950729_2235_0800G335770H.fits 
 50 -- ft950729_2235_0800G336570H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G302170H.fits 
 2 -- ft950729_2235_0800G303170H.fits 
 3 -- ft950729_2235_0800G303670H.fits 
 4 -- ft950729_2235_0800G304370H.fits 
 5 -- ft950729_2235_0800G305170H.fits 
 6 -- ft950729_2235_0800G305370H.fits 
 7 -- ft950729_2235_0800G305870H.fits 
 8 -- ft950729_2235_0800G306070H.fits 
 9 -- ft950729_2235_0800G306770H.fits 
 10 -- ft950729_2235_0800G306970H.fits 
 11 -- ft950729_2235_0800G307170H.fits 
 12 -- ft950729_2235_0800G307370H.fits 
 13 -- ft950729_2235_0800G307570H.fits 
 14 -- ft950729_2235_0800G307770H.fits 
 15 -- ft950729_2235_0800G308070H.fits 
 16 -- ft950729_2235_0800G309470H.fits 
 17 -- ft950729_2235_0800G309970H.fits 
 18 -- ft950729_2235_0800G310170H.fits 
 19 -- ft950729_2235_0800G311170H.fits 
 20 -- ft950729_2235_0800G312070H.fits 
 21 -- ft950729_2235_0800G312970H.fits 
 22 -- ft950729_2235_0800G313170H.fits 
 23 -- ft950729_2235_0800G314670H.fits 
 24 -- ft950729_2235_0800G315570H.fits 
 25 -- ft950729_2235_0800G316470H.fits 
 26 -- ft950729_2235_0800G317970H.fits 
 27 -- ft950729_2235_0800G319270H.fits 
 28 -- ft950729_2235_0800G319870H.fits 
 29 -- ft950729_2235_0800G320470H.fits 
 30 -- ft950729_2235_0800G321070H.fits 
 31 -- ft950729_2235_0800G321970H.fits 
 32 -- ft950729_2235_0800G322170H.fits 
 33 -- ft950729_2235_0800G322370H.fits 
 34 -- ft950729_2235_0800G322970H.fits 
 35 -- ft950729_2235_0800G323170H.fits 
 36 -- ft950729_2235_0800G323370H.fits 
 37 -- ft950729_2235_0800G323570H.fits 
 38 -- ft950729_2235_0800G325070H.fits 
 39 -- ft950729_2235_0800G326070H.fits 
 40 -- ft950729_2235_0800G326270H.fits 
 41 -- ft950729_2235_0800G327070H.fits 
 42 -- ft950729_2235_0800G328370H.fits 
 43 -- ft950729_2235_0800G329570H.fits 
 44 -- ft950729_2235_0800G329770H.fits 
 45 -- ft950729_2235_0800G331270H.fits 
 46 -- ft950729_2235_0800G332570H.fits 
 47 -- ft950729_2235_0800G333270H.fits 
 48 -- ft950729_2235_0800G334870H.fits 
 49 -- ft950729_2235_0800G335770H.fits 
 50 -- ft950729_2235_0800G336570H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g300270m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  52  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G300170M.fits 
 2 -- ft950729_2235_0800G300970M.fits 
 3 -- ft950729_2235_0800G301670M.fits 
 4 -- ft950729_2235_0800G302070M.fits 
 5 -- ft950729_2235_0800G302270M.fits 
 6 -- ft950729_2235_0800G303070M.fits 
 7 -- ft950729_2235_0800G303270M.fits 
 8 -- ft950729_2235_0800G303570M.fits 
 9 -- ft950729_2235_0800G303770M.fits 
 10 -- ft950729_2235_0800G304470M.fits 
 11 -- ft950729_2235_0800G305070M.fits 
 12 -- ft950729_2235_0800G305470M.fits 
 13 -- ft950729_2235_0800G305770M.fits 
 14 -- ft950729_2235_0800G306670M.fits 
 15 -- ft950729_2235_0800G308170M.fits 
 16 -- ft950729_2235_0800G308670M.fits 
 17 -- ft950729_2235_0800G309870M.fits 
 18 -- ft950729_2235_0800G311670M.fits 
 19 -- ft950729_2235_0800G312870M.fits 
 20 -- ft950729_2235_0800G313370M.fits 
 21 -- ft950729_2235_0800G314270M.fits 
 22 -- ft950729_2235_0800G315170M.fits 
 23 -- ft950729_2235_0800G317170M.fits 
 24 -- ft950729_2235_0800G317570M.fits 
 25 -- ft950729_2235_0800G318470M.fits 
 26 -- ft950729_2235_0800G318870M.fits 
 27 -- ft950729_2235_0800G319470M.fits 
 28 -- ft950729_2235_0800G320070M.fits 
 29 -- ft950729_2235_0800G320670M.fits 
 30 -- ft950729_2235_0800G321270M.fits 
 31 -- ft950729_2235_0800G321570M.fits 
 32 -- ft950729_2235_0800G322570M.fits 
 33 -- ft950729_2235_0800G322870M.fits 
 34 -- ft950729_2235_0800G323770M.fits 
 35 -- ft950729_2235_0800G324270M.fits 
 36 -- ft950729_2235_0800G325270M.fits 
 37 -- ft950729_2235_0800G325970M.fits 
 38 -- ft950729_2235_0800G327270M.fits 
 39 -- ft950729_2235_0800G328570M.fits 
 40 -- ft950729_2235_0800G329470M.fits 
 41 -- ft950729_2235_0800G329970M.fits 
 42 -- ft950729_2235_0800G330870M.fits 
 43 -- ft950729_2235_0800G331470M.fits 
 44 -- ft950729_2235_0800G333670M.fits 
 45 -- ft950729_2235_0800G333970M.fits 
 46 -- ft950729_2235_0800G335070M.fits 
 47 -- ft950729_2235_0800G335370M.fits 
 48 -- ft950729_2235_0800G335970M.fits 
 49 -- ft950729_2235_0800G336170M.fits 
 50 -- ft950729_2235_0800G336670M.fits 
 51 -- ft950729_2235_0800G336870M.fits 
 52 -- ft950729_2235_0800G337070M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G300170M.fits 
 2 -- ft950729_2235_0800G300970M.fits 
 3 -- ft950729_2235_0800G301670M.fits 
 4 -- ft950729_2235_0800G302070M.fits 
 5 -- ft950729_2235_0800G302270M.fits 
 6 -- ft950729_2235_0800G303070M.fits 
 7 -- ft950729_2235_0800G303270M.fits 
 8 -- ft950729_2235_0800G303570M.fits 
 9 -- ft950729_2235_0800G303770M.fits 
 10 -- ft950729_2235_0800G304470M.fits 
 11 -- ft950729_2235_0800G305070M.fits 
 12 -- ft950729_2235_0800G305470M.fits 
 13 -- ft950729_2235_0800G305770M.fits 
 14 -- ft950729_2235_0800G306670M.fits 
 15 -- ft950729_2235_0800G308170M.fits 
 16 -- ft950729_2235_0800G308670M.fits 
 17 -- ft950729_2235_0800G309870M.fits 
 18 -- ft950729_2235_0800G311670M.fits 
 19 -- ft950729_2235_0800G312870M.fits 
 20 -- ft950729_2235_0800G313370M.fits 
 21 -- ft950729_2235_0800G314270M.fits 
 22 -- ft950729_2235_0800G315170M.fits 
 23 -- ft950729_2235_0800G317170M.fits 
 24 -- ft950729_2235_0800G317570M.fits 
 25 -- ft950729_2235_0800G318470M.fits 
 26 -- ft950729_2235_0800G318870M.fits 
 27 -- ft950729_2235_0800G319470M.fits 
 28 -- ft950729_2235_0800G320070M.fits 
 29 -- ft950729_2235_0800G320670M.fits 
 30 -- ft950729_2235_0800G321270M.fits 
 31 -- ft950729_2235_0800G321570M.fits 
 32 -- ft950729_2235_0800G322570M.fits 
 33 -- ft950729_2235_0800G322870M.fits 
 34 -- ft950729_2235_0800G323770M.fits 
 35 -- ft950729_2235_0800G324270M.fits 
 36 -- ft950729_2235_0800G325270M.fits 
 37 -- ft950729_2235_0800G325970M.fits 
 38 -- ft950729_2235_0800G327270M.fits 
 39 -- ft950729_2235_0800G328570M.fits 
 40 -- ft950729_2235_0800G329470M.fits 
 41 -- ft950729_2235_0800G329970M.fits 
 42 -- ft950729_2235_0800G330870M.fits 
 43 -- ft950729_2235_0800G331470M.fits 
 44 -- ft950729_2235_0800G333670M.fits 
 45 -- ft950729_2235_0800G333970M.fits 
 46 -- ft950729_2235_0800G335070M.fits 
 47 -- ft950729_2235_0800G335370M.fits 
 48 -- ft950729_2235_0800G335970M.fits 
 49 -- ft950729_2235_0800G336170M.fits 
 50 -- ft950729_2235_0800G336670M.fits 
 51 -- ft950729_2235_0800G336870M.fits 
 52 -- ft950729_2235_0800G337070M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g300370l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  27  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G300270L.fits 
 2 -- ft950729_2235_0800G300570L.fits 
 3 -- ft950729_2235_0800G301070L.fits 
 4 -- ft950729_2235_0800G301770L.fits 
 5 -- ft950729_2235_0800G302470L.fits 
 6 -- ft950729_2235_0800G302670L.fits 
 7 -- ft950729_2235_0800G303470L.fits 
 8 -- ft950729_2235_0800G303970L.fits 
 9 -- ft950729_2235_0800G304670L.fits 
 10 -- ft950729_2235_0800G305670L.fits 
 11 -- ft950729_2235_0800G306270L.fits 
 12 -- ft950729_2235_0800G311270L.fits 
 13 -- ft950729_2235_0800G312170L.fits 
 14 -- ft950729_2235_0800G313570L.fits 
 15 -- ft950729_2235_0800G314770L.fits 
 16 -- ft950729_2235_0800G316770L.fits 
 17 -- ft950729_2235_0800G318070L.fits 
 18 -- ft950729_2235_0800G321470L.fits 
 19 -- ft950729_2235_0800G322770L.fits 
 20 -- ft950729_2235_0800G324670L.fits 
 21 -- ft950729_2235_0800G327470L.fits 
 22 -- ft950729_2235_0800G328770L.fits 
 23 -- ft950729_2235_0800G330170L.fits 
 24 -- ft950729_2235_0800G331670L.fits 
 25 -- ft950729_2235_0800G333870L.fits 
 26 -- ft950729_2235_0800G335270L.fits 
 27 -- ft950729_2235_0800G336070L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G300270L.fits 
 2 -- ft950729_2235_0800G300570L.fits 
 3 -- ft950729_2235_0800G301070L.fits 
 4 -- ft950729_2235_0800G301770L.fits 
 5 -- ft950729_2235_0800G302470L.fits 
 6 -- ft950729_2235_0800G302670L.fits 
 7 -- ft950729_2235_0800G303470L.fits 
 8 -- ft950729_2235_0800G303970L.fits 
 9 -- ft950729_2235_0800G304670L.fits 
 10 -- ft950729_2235_0800G305670L.fits 
 11 -- ft950729_2235_0800G306270L.fits 
 12 -- ft950729_2235_0800G311270L.fits 
 13 -- ft950729_2235_0800G312170L.fits 
 14 -- ft950729_2235_0800G313570L.fits 
 15 -- ft950729_2235_0800G314770L.fits 
 16 -- ft950729_2235_0800G316770L.fits 
 17 -- ft950729_2235_0800G318070L.fits 
 18 -- ft950729_2235_0800G321470L.fits 
 19 -- ft950729_2235_0800G322770L.fits 
 20 -- ft950729_2235_0800G324670L.fits 
 21 -- ft950729_2235_0800G327470L.fits 
 22 -- ft950729_2235_0800G328770L.fits 
 23 -- ft950729_2235_0800G330170L.fits 
 24 -- ft950729_2235_0800G331670L.fits 
 25 -- ft950729_2235_0800G333870L.fits 
 26 -- ft950729_2235_0800G335270L.fits 
 27 -- ft950729_2235_0800G336070L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g300470h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  2  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G316670H.fits 
 2 -- ft950729_2235_0800G333470H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G316670H.fits 
 2 -- ft950729_2235_0800G333470H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g300570l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  16  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G302370L.fits 
 2 -- ft950729_2235_0800G303370L.fits 
 3 -- ft950729_2235_0800G303870L.fits 
 4 -- ft950729_2235_0800G304570L.fits 
 5 -- ft950729_2235_0800G305570L.fits 
 6 -- ft950729_2235_0800G306170L.fits 
 7 -- ft950729_2235_0800G309570L.fits 
 8 -- ft950729_2235_0800G313470L.fits 
 9 -- ft950729_2235_0800G321370L.fits 
 10 -- ft950729_2235_0800G322670L.fits 
 11 -- ft950729_2235_0800G327370L.fits 
 12 -- ft950729_2235_0800G328670L.fits 
 13 -- ft950729_2235_0800G330070L.fits 
 14 -- ft950729_2235_0800G331570L.fits 
 15 -- ft950729_2235_0800G333770L.fits 
 16 -- ft950729_2235_0800G335170L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G302370L.fits 
 2 -- ft950729_2235_0800G303370L.fits 
 3 -- ft950729_2235_0800G303870L.fits 
 4 -- ft950729_2235_0800G304570L.fits 
 5 -- ft950729_2235_0800G305570L.fits 
 6 -- ft950729_2235_0800G306170L.fits 
 7 -- ft950729_2235_0800G309570L.fits 
 8 -- ft950729_2235_0800G313470L.fits 
 9 -- ft950729_2235_0800G321370L.fits 
 10 -- ft950729_2235_0800G322670L.fits 
 11 -- ft950729_2235_0800G327370L.fits 
 12 -- ft950729_2235_0800G328670L.fits 
 13 -- ft950729_2235_0800G330070L.fits 
 14 -- ft950729_2235_0800G331570L.fits 
 15 -- ft950729_2235_0800G333770L.fits 
 16 -- ft950729_2235_0800G335170L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000g300670m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  23  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800G300870M.fits 
 2 -- ft950729_2235_0800G301570M.fits 
 3 -- ft950729_2235_0800G302970M.fits 
 4 -- ft950729_2235_0800G304970M.fits 
 5 -- ft950729_2235_0800G306570M.fits 
 6 -- ft950729_2235_0800G313270M.fits 
 7 -- ft950729_2235_0800G317070M.fits 
 8 -- ft950729_2235_0800G318370M.fits 
 9 -- ft950729_2235_0800G319370M.fits 
 10 -- ft950729_2235_0800G319970M.fits 
 11 -- ft950729_2235_0800G320570M.fits 
 12 -- ft950729_2235_0800G321170M.fits 
 13 -- ft950729_2235_0800G322470M.fits 
 14 -- ft950729_2235_0800G323670M.fits 
 15 -- ft950729_2235_0800G324170M.fits 
 16 -- ft950729_2235_0800G325170M.fits 
 17 -- ft950729_2235_0800G327170M.fits 
 18 -- ft950729_2235_0800G328470M.fits 
 19 -- ft950729_2235_0800G329870M.fits 
 20 -- ft950729_2235_0800G331370M.fits 
 21 -- ft950729_2235_0800G333570M.fits 
 22 -- ft950729_2235_0800G334970M.fits 
 23 -- ft950729_2235_0800G335870M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800G300870M.fits 
 2 -- ft950729_2235_0800G301570M.fits 
 3 -- ft950729_2235_0800G302970M.fits 
 4 -- ft950729_2235_0800G304970M.fits 
 5 -- ft950729_2235_0800G306570M.fits 
 6 -- ft950729_2235_0800G313270M.fits 
 7 -- ft950729_2235_0800G317070M.fits 
 8 -- ft950729_2235_0800G318370M.fits 
 9 -- ft950729_2235_0800G319370M.fits 
 10 -- ft950729_2235_0800G319970M.fits 
 11 -- ft950729_2235_0800G320570M.fits 
 12 -- ft950729_2235_0800G321170M.fits 
 13 -- ft950729_2235_0800G322470M.fits 
 14 -- ft950729_2235_0800G323670M.fits 
 15 -- ft950729_2235_0800G324170M.fits 
 16 -- ft950729_2235_0800G325170M.fits 
 17 -- ft950729_2235_0800G327170M.fits 
 18 -- ft950729_2235_0800G328470M.fits 
 19 -- ft950729_2235_0800G329870M.fits 
 20 -- ft950729_2235_0800G331370M.fits 
 21 -- ft950729_2235_0800G333570M.fits 
 22 -- ft950729_2235_0800G334970M.fits 
 23 -- ft950729_2235_0800G335870M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Ignoring the following files containing 000000124 events
ft950729_2235_0800G301270L.fits
ft950729_2235_0800G308570L.fits
ft950729_2235_0800G309070L.fits
-> Ignoring the following files containing 000000114 events
ft950729_2235_0800G301970M.fits
ft950729_2235_0800G311570M.fits
ft950729_2235_0800G312770M.fits
ft950729_2235_0800G314170M.fits
ft950729_2235_0800G315070M.fits
ft950729_2235_0800G317470M.fits
ft950729_2235_0800G318770M.fits
ft950729_2235_0800G325870M.fits
ft950729_2235_0800G329370M.fits
ft950729_2235_0800G330770M.fits
-> Ignoring the following files containing 000000063 events
ft950729_2235_0800G310370H.fits
ft950729_2235_0800G315670H.fits
ft950729_2235_0800G326470H.fits
ft950729_2235_0800G332670H.fits
-> Ignoring the following files containing 000000052 events
ft950729_2235_0800G336770M.fits
-> Ignoring the following files containing 000000051 events
ft950729_2235_0800G304270H.fits
ft950729_2235_0800G309370H.fits
ft950729_2235_0800G311970H.fits
ft950729_2235_0800G314570H.fits
ft950729_2235_0800G315470H.fits
ft950729_2235_0800G317870H.fits
ft950729_2235_0800G319170H.fits
ft950729_2235_0800G319770H.fits
ft950729_2235_0800G320370H.fits
ft950729_2235_0800G320970H.fits
ft950729_2235_0800G321870H.fits
ft950729_2235_0800G324970H.fits
ft950729_2235_0800G331170H.fits
ft950729_2235_0800G335670H.fits
ft950729_2235_0800G336470H.fits
-> Ignoring the following files containing 000000051 events
ft950729_2235_0800G300470L.fits
ft950729_2235_0800G302570L.fits
ft950729_2235_0800G309670L.fits
ft950729_2235_0800G311370L.fits
ft950729_2235_0800G323870L.fits
-> Ignoring the following files containing 000000050 events
ft950729_2235_0800G324570L.fits
-> Ignoring the following files containing 000000041 events
ft950729_2235_0800G301370M.fits
-> Ignoring the following files containing 000000037 events
ft950729_2235_0800G300770M.fits
-> Ignoring the following files containing 000000036 events
ft950729_2235_0800G302770M.fits
-> Ignoring the following files containing 000000035 events
ft950729_2235_0800G301470M.fits
-> Ignoring the following files containing 000000033 events
ft950729_2235_0800G300670M.fits
-> Ignoring the following files containing 000000027 events
ft950729_2235_0800G302870M.fits
-> Ignoring the following files containing 000000022 events
ft950729_2235_0800G323970M.fits
-> Ignoring the following files containing 000000020 events
ft950729_2235_0800G308270M.fits
ft950729_2235_0800G308770M.fits
ft950729_2235_0800G318570M.fits
ft950729_2235_0800G325370M.fits
ft950729_2235_0800G334070M.fits
-> Ignoring the following files containing 000000015 events
ft950729_2235_0800G324070M.fits
-> Ignoring the following files containing 000000015 events
ft950729_2235_0800G336970M.fits
-> Ignoring the following files containing 000000014 events
ft950729_2235_0800G306870H.fits
-> Ignoring the following files containing 000000013 events
ft950729_2235_0800G316870M.fits
-> Ignoring the following files containing 000000012 events
ft950729_2235_0800G316970M.fits
-> Ignoring the following files containing 000000012 events
ft950729_2235_0800G306470M.fits
-> Ignoring the following files containing 000000012 events
ft950729_2235_0800G322070H.fits
-> Ignoring the following files containing 000000012 events
ft950729_2235_0800G300370L.fits
-> Ignoring the following files containing 000000011 events
ft950729_2235_0800G319670H.fits
-> Ignoring the following files containing 000000011 events
ft950729_2235_0800G306370M.fits
-> Ignoring the following files containing 000000010 events
ft950729_2235_0800G335570H.fits
-> Ignoring the following files containing 000000010 events
ft950729_2235_0800G313070H.fits
-> Ignoring the following files containing 000000010 events
ft950729_2235_0800G318170M.fits
-> Ignoring the following files containing 000000010 events
ft950729_2235_0800G304770M.fits
-> Ignoring the following files containing 000000009 events
ft950729_2235_0800G321770H.fits
-> Ignoring the following files containing 000000009 events
ft950729_2235_0800G307270H.fits
-> Ignoring the following files containing 000000008 events
ft950729_2235_0800G335470H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G318970H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G305270H.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G304870M.fits
-> Ignoring the following files containing 000000007 events
ft950729_2235_0800G328270H.fits
ft950729_2235_0800G332470H.fits
ft950729_2235_0800G334770H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G307070H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G317770H.fits
-> Ignoring the following files containing 000000006 events
ft950729_2235_0800G307670H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G304070H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G319570H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G314470H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G314370H.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G318270M.fits
-> Ignoring the following files containing 000000005 events
ft950729_2235_0800G316370H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G310970H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G323470H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G322270H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G315370H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G330970H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G304170H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G311870H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G326370H.fits
-> Ignoring the following files containing 000000004 events
ft950729_2235_0800G307470H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G305970H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G315270H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G317670H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G320270H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G321670H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G324770H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G311770H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G333170H.fits
-> Ignoring the following files containing 000000003 events
ft950729_2235_0800G323070H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G326870H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G333070H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G319070H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G309270H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G320170H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G307970H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G311070H.fits
-> Ignoring the following files containing 000000002 events
ft950729_2235_0800G324370L.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G315770H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G307870H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G331070H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G309170H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G336370H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G320870H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G326970H.fits
-> Ignoring the following files containing 000000001 events
ft950729_2235_0800G332370H.fits
-> Collecting SIS0 event files by mode
-> Standard Error Output From STOOL sis0sortcode:
SIS0SORTCODE:LO:Start program
SIS0SORTCODE:LO:End program
-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program
SIS0SORTSPLIT:LO:s000101h.prelist merge count = 38 photon cnt = 928439
SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 53734
SIS0SORTSPLIT:LO:s000301h.prelist merge count = 15 photon cnt = 175630
SIS0SORTSPLIT:LO:s000401h.prelist merge count = 3 photon cnt = 172
SIS0SORTSPLIT:LO:s000501l.prelist merge count = 2 photon cnt = 144
SIS0SORTSPLIT:LO:s000601m.prelist merge count = 14 photon cnt = 438
SIS0SORTSPLIT:LO:s000702h.prelist merge count = 1 photon cnt = 23
SIS0SORTSPLIT:LO:s000802l.prelist merge count = 17 photon cnt = 46263
SIS0SORTSPLIT:LO:s000902l.prelist merge count = 17 photon cnt = 3089
SIS0SORTSPLIT:LO:s001002l.prelist merge count = 7 photon cnt = 1099
SIS0SORTSPLIT:LO:s001102l.prelist merge count = 1 photon cnt = 125
SIS0SORTSPLIT:LO:s001202m.prelist merge count = 1 photon cnt = 734
SIS0SORTSPLIT:LO:s001302m.prelist merge count = 42 photon cnt = 563461
SIS0SORTSPLIT:LO:s001402m.prelist merge count = 32 photon cnt = 18955
SIS0SORTSPLIT:LO:s001502m.prelist merge count = 2 photon cnt = 106
SIS0SORTSPLIT:LO:Total filenames split = 193
SIS0SORTSPLIT:LO:Total split file cnt = 15
SIS0SORTSPLIT:LO:End program
-> Creating ad63007000s000101h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  38  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S002001H.fits 
 2 -- ft950729_2235_0800S002801H.fits 
 3 -- ft950729_2235_0800S003401H.fits 
 4 -- ft950729_2235_0800S004001H.fits 
 5 -- ft950729_2235_0800S004601H.fits 
 6 -- ft950729_2235_0800S005101H.fits 
 7 -- ft950729_2235_0800S005901H.fits 
 8 -- ft950729_2235_0800S006101H.fits 
 9 -- ft950729_2235_0800S007401H.fits 
 10 -- ft950729_2235_0800S008401H.fits 
 11 -- ft950729_2235_0800S008601H.fits 
 12 -- ft950729_2235_0800S009401H.fits 
 13 -- ft950729_2235_0800S010301H.fits 
 14 -- ft950729_2235_0800S011301H.fits 
 15 -- ft950729_2235_0800S012201H.fits 
 16 -- ft950729_2235_0800S012401H.fits 
 17 -- ft950729_2235_0800S013301H.fits 
 18 -- ft950729_2235_0800S014001H.fits 
 19 -- ft950729_2235_0800S014601H.fits 
 20 -- ft950729_2235_0800S015201H.fits 
 21 -- ft950729_2235_0800S015801H.fits 
 22 -- ft950729_2235_0800S016601H.fits 
 23 -- ft950729_2235_0800S016801H.fits 
 24 -- ft950729_2235_0800S017801H.fits 
 25 -- ft950729_2235_0800S018101H.fits 
 26 -- ft950729_2235_0800S018301H.fits 
 27 -- ft950729_2235_0800S019801H.fits 
 28 -- ft950729_2235_0800S020701H.fits 
 29 -- ft950729_2235_0800S020901H.fits 
 30 -- ft950729_2235_0800S021701H.fits 
 31 -- ft950729_2235_0800S022601H.fits 
 32 -- ft950729_2235_0800S022801H.fits 
 33 -- ft950729_2235_0800S023701H.fits 
 34 -- ft950729_2235_0800S024601H.fits 
 35 -- ft950729_2235_0800S024801H.fits 
 36 -- ft950729_2235_0800S025801H.fits 
 37 -- ft950729_2235_0800S026601H.fits 
 38 -- ft950729_2235_0800S027401H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S002001H.fits 
 2 -- ft950729_2235_0800S002801H.fits 
 3 -- ft950729_2235_0800S003401H.fits 
 4 -- ft950729_2235_0800S004001H.fits 
 5 -- ft950729_2235_0800S004601H.fits 
 6 -- ft950729_2235_0800S005101H.fits 
 7 -- ft950729_2235_0800S005901H.fits 
 8 -- ft950729_2235_0800S006101H.fits 
 9 -- ft950729_2235_0800S007401H.fits 
 10 -- ft950729_2235_0800S008401H.fits 
 11 -- ft950729_2235_0800S008601H.fits 
 12 -- ft950729_2235_0800S009401H.fits 
 13 -- ft950729_2235_0800S010301H.fits 
 14 -- ft950729_2235_0800S011301H.fits 
 15 -- ft950729_2235_0800S012201H.fits 
 16 -- ft950729_2235_0800S012401H.fits 
 17 -- ft950729_2235_0800S013301H.fits 
 18 -- ft950729_2235_0800S014001H.fits 
 19 -- ft950729_2235_0800S014601H.fits 
 20 -- ft950729_2235_0800S015201H.fits 
 21 -- ft950729_2235_0800S015801H.fits 
 22 -- ft950729_2235_0800S016601H.fits 
 23 -- ft950729_2235_0800S016801H.fits 
 24 -- ft950729_2235_0800S017801H.fits 
 25 -- ft950729_2235_0800S018101H.fits 
 26 -- ft950729_2235_0800S018301H.fits 
 27 -- ft950729_2235_0800S019801H.fits 
 28 -- ft950729_2235_0800S020701H.fits 
 29 -- ft950729_2235_0800S020901H.fits 
 30 -- ft950729_2235_0800S021701H.fits 
 31 -- ft950729_2235_0800S022601H.fits 
 32 -- ft950729_2235_0800S022801H.fits 
 33 -- ft950729_2235_0800S023701H.fits 
 34 -- ft950729_2235_0800S024601H.fits 
 35 -- ft950729_2235_0800S024801H.fits 
 36 -- ft950729_2235_0800S025801H.fits 
 37 -- ft950729_2235_0800S026601H.fits 
 38 -- ft950729_2235_0800S027401H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000202m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  42  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S000602M.fits 
 2 -- ft950729_2235_0800S001202M.fits 
 3 -- ft950729_2235_0800S001602M.fits 
 4 -- ft950729_2235_0800S001802M.fits 
 5 -- ft950729_2235_0800S002702M.fits 
 6 -- ft950729_2235_0800S002902M.fits 
 7 -- ft950729_2235_0800S003202M.fits 
 8 -- ft950729_2235_0800S004402M.fits 
 9 -- ft950729_2235_0800S005002M.fits 
 10 -- ft950729_2235_0800S005602M.fits 
 11 -- ft950729_2235_0800S006702M.fits 
 12 -- ft950729_2235_0800S008202M.fits 
 13 -- ft950729_2235_0800S009202M.fits 
 14 -- ft950729_2235_0800S010102M.fits 
 15 -- ft950729_2235_0800S010502M.fits 
 16 -- ft950729_2235_0800S011102M.fits 
 17 -- ft950729_2235_0800S012002M.fits 
 18 -- ft950729_2235_0800S012902M.fits 
 19 -- ft950729_2235_0800S013102M.fits 
 20 -- ft950729_2235_0800S013802M.fits 
 21 -- ft950729_2235_0800S014402M.fits 
 22 -- ft950729_2235_0800S015002M.fits 
 23 -- ft950729_2235_0800S015602M.fits 
 24 -- ft950729_2235_0800S016002M.fits 
 25 -- ft950729_2235_0800S016402M.fits 
 26 -- ft950729_2235_0800S017402M.fits 
 27 -- ft950729_2235_0800S017602M.fits 
 28 -- ft950729_2235_0800S018502M.fits 
 29 -- ft950729_2235_0800S019102M.fits 
 30 -- ft950729_2235_0800S020002M.fits 
 31 -- ft950729_2235_0800S020602M.fits 
 32 -- ft950729_2235_0800S021102M.fits 
 33 -- ft950729_2235_0800S022402M.fits 
 34 -- ft950729_2235_0800S023002M.fits 
 35 -- ft950729_2235_0800S023502M.fits 
 36 -- ft950729_2235_0800S023902M.fits 
 37 -- ft950729_2235_0800S025402M.fits 
 38 -- ft950729_2235_0800S026002M.fits 
 39 -- ft950729_2235_0800S026402M.fits 
 40 -- ft950729_2235_0800S026802M.fits 
 41 -- ft950729_2235_0800S027202M.fits 
 42 -- ft950729_2235_0800S027502M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S000602M.fits 
 2 -- ft950729_2235_0800S001202M.fits 
 3 -- ft950729_2235_0800S001602M.fits 
 4 -- ft950729_2235_0800S001802M.fits 
 5 -- ft950729_2235_0800S002702M.fits 
 6 -- ft950729_2235_0800S002902M.fits 
 7 -- ft950729_2235_0800S003202M.fits 
 8 -- ft950729_2235_0800S004402M.fits 
 9 -- ft950729_2235_0800S005002M.fits 
 10 -- ft950729_2235_0800S005602M.fits 
 11 -- ft950729_2235_0800S006702M.fits 
 12 -- ft950729_2235_0800S008202M.fits 
 13 -- ft950729_2235_0800S009202M.fits 
 14 -- ft950729_2235_0800S010102M.fits 
 15 -- ft950729_2235_0800S010502M.fits 
 16 -- ft950729_2235_0800S011102M.fits 
 17 -- ft950729_2235_0800S012002M.fits 
 18 -- ft950729_2235_0800S012902M.fits 
 19 -- ft950729_2235_0800S013102M.fits 
 20 -- ft950729_2235_0800S013802M.fits 
 21 -- ft950729_2235_0800S014402M.fits 
 22 -- ft950729_2235_0800S015002M.fits 
 23 -- ft950729_2235_0800S015602M.fits 
 24 -- ft950729_2235_0800S016002M.fits 
 25 -- ft950729_2235_0800S016402M.fits 
 26 -- ft950729_2235_0800S017402M.fits 
 27 -- ft950729_2235_0800S017602M.fits 
 28 -- ft950729_2235_0800S018502M.fits 
 29 -- ft950729_2235_0800S019102M.fits 
 30 -- ft950729_2235_0800S020002M.fits 
 31 -- ft950729_2235_0800S020602M.fits 
 32 -- ft950729_2235_0800S021102M.fits 
 33 -- ft950729_2235_0800S022402M.fits 
 34 -- ft950729_2235_0800S023002M.fits 
 35 -- ft950729_2235_0800S023502M.fits 
 36 -- ft950729_2235_0800S023902M.fits 
 37 -- ft950729_2235_0800S025402M.fits 
 38 -- ft950729_2235_0800S026002M.fits 
 39 -- ft950729_2235_0800S026402M.fits 
 40 -- ft950729_2235_0800S026802M.fits 
 41 -- ft950729_2235_0800S027202M.fits 
 42 -- ft950729_2235_0800S027502M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000301h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  15  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S002101H.fits 
 2 -- ft950729_2235_0800S004701H.fits 
 3 -- ft950729_2235_0800S005201H.fits 
 4 -- ft950729_2235_0800S007501H.fits 
 5 -- ft950729_2235_0800S008701H.fits 
 6 -- ft950729_2235_0800S009501H.fits 
 7 -- ft950729_2235_0800S011401H.fits 
 8 -- ft950729_2235_0800S012501H.fits 
 9 -- ft950729_2235_0800S013401H.fits 
 10 -- ft950729_2235_0800S014101H.fits 
 11 -- ft950729_2235_0800S014701H.fits 
 12 -- ft950729_2235_0800S015301H.fits 
 13 -- ft950729_2235_0800S017901H.fits 
 14 -- ft950729_2235_0800S021801H.fits 
 15 -- ft950729_2235_0800S024901H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S002101H.fits 
 2 -- ft950729_2235_0800S004701H.fits 
 3 -- ft950729_2235_0800S005201H.fits 
 4 -- ft950729_2235_0800S007501H.fits 
 5 -- ft950729_2235_0800S008701H.fits 
 6 -- ft950729_2235_0800S009501H.fits 
 7 -- ft950729_2235_0800S011401H.fits 
 8 -- ft950729_2235_0800S012501H.fits 
 9 -- ft950729_2235_0800S013401H.fits 
 10 -- ft950729_2235_0800S014101H.fits 
 11 -- ft950729_2235_0800S014701H.fits 
 12 -- ft950729_2235_0800S015301H.fits 
 13 -- ft950729_2235_0800S017901H.fits 
 14 -- ft950729_2235_0800S021801H.fits 
 15 -- ft950729_2235_0800S024901H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Checking ft950729_2235_0800S005801H.fits
-> Creating ad63007000s000401h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S005801H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S005801H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000502l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  17  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S000502L.fits 
 2 -- ft950729_2235_0800S000902L.fits 
 3 -- ft950729_2235_0800S001102L.fits 
 4 -- ft950729_2235_0800S001502L.fits 
 5 -- ft950729_2235_0800S002402L.fits 
 6 -- ft950729_2235_0800S002602L.fits 
 7 -- ft950729_2235_0800S003802L.fits 
 8 -- ft950729_2235_0800S006602L.fits 
 9 -- ft950729_2235_0800S007202L.fits 
 10 -- ft950729_2235_0800S008002L.fits 
 11 -- ft950729_2235_0800S010002L.fits 
 12 -- ft950729_2235_0800S011002L.fits 
 13 -- ft950729_2235_0800S011702L.fits 
 14 -- ft950729_2235_0800S019002L.fits 
 15 -- ft950729_2235_0800S019602L.fits 
 16 -- ft950729_2235_0800S024202L.fits 
 17 -- ft950729_2235_0800S025602L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S000502L.fits 
 2 -- ft950729_2235_0800S000902L.fits 
 3 -- ft950729_2235_0800S001102L.fits 
 4 -- ft950729_2235_0800S001502L.fits 
 5 -- ft950729_2235_0800S002402L.fits 
 6 -- ft950729_2235_0800S002602L.fits 
 7 -- ft950729_2235_0800S003802L.fits 
 8 -- ft950729_2235_0800S006602L.fits 
 9 -- ft950729_2235_0800S007202L.fits 
 10 -- ft950729_2235_0800S008002L.fits 
 11 -- ft950729_2235_0800S010002L.fits 
 12 -- ft950729_2235_0800S011002L.fits 
 13 -- ft950729_2235_0800S011702L.fits 
 14 -- ft950729_2235_0800S019002L.fits 
 15 -- ft950729_2235_0800S019602L.fits 
 16 -- ft950729_2235_0800S024202L.fits 
 17 -- ft950729_2235_0800S025602L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000602m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  32  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S000102M.fits 
 2 -- ft950729_2235_0800S000702M.fits 
 3 -- ft950729_2235_0800S001302M.fits 
 4 -- ft950729_2235_0800S003002M.fits 
 5 -- ft950729_2235_0800S003602M.fits 
 6 -- ft950729_2235_0800S004202M.fits 
 7 -- ft950729_2235_0800S005502M.fits 
 8 -- ft950729_2235_0800S006302M.fits 
 9 -- ft950729_2235_0800S006802M.fits 
 10 -- ft950729_2235_0800S010602M.fits 
 11 -- ft950729_2235_0800S012802M.fits 
 12 -- ft950729_2235_0800S013702M.fits 
 13 -- ft950729_2235_0800S014302M.fits 
 14 -- ft950729_2235_0800S014902M.fits 
 15 -- ft950729_2235_0800S015502M.fits 
 16 -- ft950729_2235_0800S016102M.fits 
 17 -- ft950729_2235_0800S016302M.fits 
 18 -- ft950729_2235_0800S017102M.fits 
 19 -- ft950729_2235_0800S017302M.fits 
 20 -- ft950729_2235_0800S018602M.fits 
 21 -- ft950729_2235_0800S019202M.fits 
 22 -- ft950729_2235_0800S020102M.fits 
 23 -- ft950729_2235_0800S021202M.fits 
 24 -- ft950729_2235_0800S022002M.fits 
 25 -- ft950729_2235_0800S023102M.fits 
 26 -- ft950729_2235_0800S024002M.fits 
 27 -- ft950729_2235_0800S025302M.fits 
 28 -- ft950729_2235_0800S026102M.fits 
 29 -- ft950729_2235_0800S026302M.fits 
 30 -- ft950729_2235_0800S026902M.fits 
 31 -- ft950729_2235_0800S027102M.fits 
 32 -- ft950729_2235_0800S027602M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S000102M.fits 
 2 -- ft950729_2235_0800S000702M.fits 
 3 -- ft950729_2235_0800S001302M.fits 
 4 -- ft950729_2235_0800S003002M.fits 
 5 -- ft950729_2235_0800S003602M.fits 
 6 -- ft950729_2235_0800S004202M.fits 
 7 -- ft950729_2235_0800S005502M.fits 
 8 -- ft950729_2235_0800S006302M.fits 
 9 -- ft950729_2235_0800S006802M.fits 
 10 -- ft950729_2235_0800S010602M.fits 
 11 -- ft950729_2235_0800S012802M.fits 
 12 -- ft950729_2235_0800S013702M.fits 
 13 -- ft950729_2235_0800S014302M.fits 
 14 -- ft950729_2235_0800S014902M.fits 
 15 -- ft950729_2235_0800S015502M.fits 
 16 -- ft950729_2235_0800S016102M.fits 
 17 -- ft950729_2235_0800S016302M.fits 
 18 -- ft950729_2235_0800S017102M.fits 
 19 -- ft950729_2235_0800S017302M.fits 
 20 -- ft950729_2235_0800S018602M.fits 
 21 -- ft950729_2235_0800S019202M.fits 
 22 -- ft950729_2235_0800S020102M.fits 
 23 -- ft950729_2235_0800S021202M.fits 
 24 -- ft950729_2235_0800S022002M.fits 
 25 -- ft950729_2235_0800S023102M.fits 
 26 -- ft950729_2235_0800S024002M.fits 
 27 -- ft950729_2235_0800S025302M.fits 
 28 -- ft950729_2235_0800S026102M.fits 
 29 -- ft950729_2235_0800S026302M.fits 
 30 -- ft950729_2235_0800S026902M.fits 
 31 -- ft950729_2235_0800S027102M.fits 
 32 -- ft950729_2235_0800S027602M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000702l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  17  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S000802L.fits 
 2 -- ft950729_2235_0800S001402L.fits 
 3 -- ft950729_2235_0800S002302L.fits 
 4 -- ft950729_2235_0800S003102L.fits 
 5 -- ft950729_2235_0800S004902L.fits 
 6 -- ft950729_2235_0800S005402L.fits 
 7 -- ft950729_2235_0800S011602L.fits 
 8 -- ft950729_2235_0800S012702L.fits 
 9 -- ft950729_2235_0800S013602L.fits 
 10 -- ft950729_2235_0800S016202L.fits 
 11 -- ft950729_2235_0800S017202L.fits 
 12 -- ft950729_2235_0800S018702L.fits 
 13 -- ft950729_2235_0800S018902L.fits 
 14 -- ft950729_2235_0800S024102L.fits 
 15 -- ft950729_2235_0800S025202L.fits 
 16 -- ft950729_2235_0800S026202L.fits 
 17 -- ft950729_2235_0800S027002L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S000802L.fits 
 2 -- ft950729_2235_0800S001402L.fits 
 3 -- ft950729_2235_0800S002302L.fits 
 4 -- ft950729_2235_0800S003102L.fits 
 5 -- ft950729_2235_0800S004902L.fits 
 6 -- ft950729_2235_0800S005402L.fits 
 7 -- ft950729_2235_0800S011602L.fits 
 8 -- ft950729_2235_0800S012702L.fits 
 9 -- ft950729_2235_0800S013602L.fits 
 10 -- ft950729_2235_0800S016202L.fits 
 11 -- ft950729_2235_0800S017202L.fits 
 12 -- ft950729_2235_0800S018702L.fits 
 13 -- ft950729_2235_0800S018902L.fits 
 14 -- ft950729_2235_0800S024102L.fits 
 15 -- ft950729_2235_0800S025202L.fits 
 16 -- ft950729_2235_0800S026202L.fits 
 17 -- ft950729_2235_0800S027002L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s000802l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  7  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S000402L.fits 
 2 -- ft950729_2235_0800S001002L.fits 
 3 -- ft950729_2235_0800S002502L.fits 
 4 -- ft950729_2235_0800S019502L.fits 
 5 -- ft950729_2235_0800S022302L.fits 
 6 -- ft950729_2235_0800S023402L.fits 
 7 -- ft950729_2235_0800S025502L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S000402L.fits 
 2 -- ft950729_2235_0800S001002L.fits 
 3 -- ft950729_2235_0800S002502L.fits 
 4 -- ft950729_2235_0800S019502L.fits 
 5 -- ft950729_2235_0800S022302L.fits 
 6 -- ft950729_2235_0800S023402L.fits 
 7 -- ft950729_2235_0800S025502L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Ignoring the following files containing 000000734 events
ft950729_2235_0800S017502M.fits
-> Ignoring the following files containing 000000438 events
ft950729_2235_0800S009301M.fits
ft950729_2235_0800S010201M.fits
ft950729_2235_0800S011201M.fits
ft950729_2235_0800S012101M.fits
ft950729_2235_0800S013201M.fits
ft950729_2235_0800S013901M.fits
ft950729_2235_0800S014501M.fits
ft950729_2235_0800S015101M.fits
ft950729_2235_0800S015701M.fits
ft950729_2235_0800S016501M.fits
ft950729_2235_0800S022501M.fits
ft950729_2235_0800S023601M.fits
ft950729_2235_0800S026501M.fits
ft950729_2235_0800S027301M.fits
-> Ignoring the following files containing 000000172 events
ft950729_2235_0800S006001H.fits
ft950729_2235_0800S016701H.fits
ft950729_2235_0800S018201H.fits
-> Ignoring the following files containing 000000144 events
ft950729_2235_0800S019701L.fits
ft950729_2235_0800S025701L.fits
-> Ignoring the following files containing 000000125 events
ft950729_2235_0800S006502L.fits
-> Ignoring the following files containing 000000106 events
ft950729_2235_0800S013002M.fits
ft950729_2235_0800S017702M.fits
-> Ignoring the following files containing 000000023 events
ft950729_2235_0800S012602H.fits
-> Collecting SIS1 event files by mode
-> Standard Error Output From STOOL sis1sortcode:
SIS1SORTCODE:LO:Start program
SIS1SORTCODE:LO:End program
-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program
SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 119
SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 47
SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 18053
SIS1SORTSPLIT:LO:s100401h.prelist merge count = 1 photon cnt = 125
SIS1SORTSPLIT:LO:s100501h.prelist merge count = 41 photon cnt = 932109
SIS1SORTSPLIT:LO:s100601h.prelist merge count = 3 photon cnt = 189
SIS1SORTSPLIT:LO:s100701l.prelist merge count = 2 photon cnt = 144
SIS1SORTSPLIT:LO:s100801m.prelist merge count = 14 photon cnt = 448
SIS1SORTSPLIT:LO:s100902h.prelist merge count = 2 photon cnt = 169
SIS1SORTSPLIT:LO:s101002l.prelist merge count = 33 photon cnt = 60525
SIS1SORTSPLIT:LO:s101102l.prelist merge count = 8 photon cnt = 704
SIS1SORTSPLIT:LO:s101202m.prelist merge count = 1 photon cnt = 628
SIS1SORTSPLIT:LO:s101302m.prelist merge count = 51 photon cnt = 565354
SIS1SORTSPLIT:LO:s101402m.prelist merge count = 2 photon cnt = 138
SIS1SORTSPLIT:LO:Total filenames split = 161
SIS1SORTSPLIT:LO:Total split file cnt = 14
SIS1SORTSPLIT:LO:End program
-> Creating ad63007000s100101h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  41  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S101501H.fits 
 2 -- ft950729_2235_0800S102101H.fits 
 3 -- ft950729_2235_0800S102601H.fits 
 4 -- ft950729_2235_0800S103001H.fits 
 5 -- ft950729_2235_0800S103601H.fits 
 6 -- ft950729_2235_0800S104001H.fits 
 7 -- ft950729_2235_0800S104201H.fits 
 8 -- ft950729_2235_0800S104701H.fits 
 9 -- ft950729_2235_0800S104901H.fits 
 10 -- ft950729_2235_0800S105101H.fits 
 11 -- ft950729_2235_0800S106101H.fits 
 12 -- ft950729_2235_0800S106901H.fits 
 13 -- ft950729_2235_0800S107101H.fits 
 14 -- ft950729_2235_0800S107701H.fits 
 15 -- ft950729_2235_0800S108401H.fits 
 16 -- ft950729_2235_0800S109201H.fits 
 17 -- ft950729_2235_0800S109901H.fits 
 18 -- ft950729_2235_0800S110101H.fits 
 19 -- ft950729_2235_0800S110801H.fits 
 20 -- ft950729_2235_0800S111301H.fits 
 21 -- ft950729_2235_0800S111701H.fits 
 22 -- ft950729_2235_0800S112101H.fits 
 23 -- ft950729_2235_0800S112501H.fits 
 24 -- ft950729_2235_0800S113101H.fits 
 25 -- ft950729_2235_0800S113301H.fits 
 26 -- ft950729_2235_0800S114101H.fits 
 27 -- ft950729_2235_0800S114301H.fits 
 28 -- ft950729_2235_0800S114501H.fits 
 29 -- ft950729_2235_0800S114701H.fits 
 30 -- ft950729_2235_0800S115801H.fits 
 31 -- ft950729_2235_0800S116501H.fits 
 32 -- ft950729_2235_0800S116701H.fits 
 33 -- ft950729_2235_0800S117301H.fits 
 34 -- ft950729_2235_0800S118001H.fits 
 35 -- ft950729_2235_0800S118201H.fits 
 36 -- ft950729_2235_0800S118901H.fits 
 37 -- ft950729_2235_0800S119601H.fits 
 38 -- ft950729_2235_0800S119801H.fits 
 39 -- ft950729_2235_0800S120601H.fits 
 40 -- ft950729_2235_0800S121201H.fits 
 41 -- ft950729_2235_0800S121801H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S101501H.fits 
 2 -- ft950729_2235_0800S102101H.fits 
 3 -- ft950729_2235_0800S102601H.fits 
 4 -- ft950729_2235_0800S103001H.fits 
 5 -- ft950729_2235_0800S103601H.fits 
 6 -- ft950729_2235_0800S104001H.fits 
 7 -- ft950729_2235_0800S104201H.fits 
 8 -- ft950729_2235_0800S104701H.fits 
 9 -- ft950729_2235_0800S104901H.fits 
 10 -- ft950729_2235_0800S105101H.fits 
 11 -- ft950729_2235_0800S106101H.fits 
 12 -- ft950729_2235_0800S106901H.fits 
 13 -- ft950729_2235_0800S107101H.fits 
 14 -- ft950729_2235_0800S107701H.fits 
 15 -- ft950729_2235_0800S108401H.fits 
 16 -- ft950729_2235_0800S109201H.fits 
 17 -- ft950729_2235_0800S109901H.fits 
 18 -- ft950729_2235_0800S110101H.fits 
 19 -- ft950729_2235_0800S110801H.fits 
 20 -- ft950729_2235_0800S111301H.fits 
 21 -- ft950729_2235_0800S111701H.fits 
 22 -- ft950729_2235_0800S112101H.fits 
 23 -- ft950729_2235_0800S112501H.fits 
 24 -- ft950729_2235_0800S113101H.fits 
 25 -- ft950729_2235_0800S113301H.fits 
 26 -- ft950729_2235_0800S114101H.fits 
 27 -- ft950729_2235_0800S114301H.fits 
 28 -- ft950729_2235_0800S114501H.fits 
 29 -- ft950729_2235_0800S114701H.fits 
 30 -- ft950729_2235_0800S115801H.fits 
 31 -- ft950729_2235_0800S116501H.fits 
 32 -- ft950729_2235_0800S116701H.fits 
 33 -- ft950729_2235_0800S117301H.fits 
 34 -- ft950729_2235_0800S118001H.fits 
 35 -- ft950729_2235_0800S118201H.fits 
 36 -- ft950729_2235_0800S118901H.fits 
 37 -- ft950729_2235_0800S119601H.fits 
 38 -- ft950729_2235_0800S119801H.fits 
 39 -- ft950729_2235_0800S120601H.fits 
 40 -- ft950729_2235_0800S121201H.fits 
 41 -- ft950729_2235_0800S121801H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s100202m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  51  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S100102M.fits 
 2 -- ft950729_2235_0800S100502M.fits 
 3 -- ft950729_2235_0800S100902M.fits 
 4 -- ft950729_2235_0800S101102M.fits 
 5 -- ft950729_2235_0800S101302M.fits 
 6 -- ft950729_2235_0800S101602M.fits 
 7 -- ft950729_2235_0800S102002M.fits 
 8 -- ft950729_2235_0800S102202M.fits 
 9 -- ft950729_2235_0800S102402M.fits 
 10 -- ft950729_2235_0800S102702M.fits 
 11 -- ft950729_2235_0800S103102M.fits 
 12 -- ft950729_2235_0800S103302M.fits 
 13 -- ft950729_2235_0800S103702M.fits 
 14 -- ft950729_2235_0800S103902M.fits 
 15 -- ft950729_2235_0800S104502M.fits 
 16 -- ft950729_2235_0800S105202M.fits 
 17 -- ft950729_2235_0800S105602M.fits 
 18 -- ft950729_2235_0800S106702M.fits 
 19 -- ft950729_2235_0800S107502M.fits 
 20 -- ft950729_2235_0800S108202M.fits 
 21 -- ft950729_2235_0800S108602M.fits 
 22 -- ft950729_2235_0800S109002M.fits 
 23 -- ft950729_2235_0800S109702M.fits 
 24 -- ft950729_2235_0800S110402M.fits 
 25 -- ft950729_2235_0800S110602M.fits 
 26 -- ft950729_2235_0800S111102M.fits 
 27 -- ft950729_2235_0800S111502M.fits 
 28 -- ft950729_2235_0800S111902M.fits 
 29 -- ft950729_2235_0800S112302M.fits 
 30 -- ft950729_2235_0800S112702M.fits 
 31 -- ft950729_2235_0800S112902M.fits 
 32 -- ft950729_2235_0800S113502M.fits 
 33 -- ft950729_2235_0800S113702M.fits 
 34 -- ft950729_2235_0800S113902M.fits 
 35 -- ft950729_2235_0800S114902M.fits 
 36 -- ft950729_2235_0800S115302M.fits 
 37 -- ft950729_2235_0800S116002M.fits 
 38 -- ft950729_2235_0800S116402M.fits 
 39 -- ft950729_2235_0800S116902M.fits 
 40 -- ft950729_2235_0800S117502M.fits 
 41 -- ft950729_2235_0800S117802M.fits 
 42 -- ft950729_2235_0800S118402M.fits 
 43 -- ft950729_2235_0800S118702M.fits 
 44 -- ft950729_2235_0800S119102M.fits 
 45 -- ft950729_2235_0800S120002M.fits 
 46 -- ft950729_2235_0800S120202M.fits 
 47 -- ft950729_2235_0800S120802M.fits 
 48 -- ft950729_2235_0800S121002M.fits 
 49 -- ft950729_2235_0800S121402M.fits 
 50 -- ft950729_2235_0800S121602M.fits 
 51 -- ft950729_2235_0800S121902M.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S100102M.fits 
 2 -- ft950729_2235_0800S100502M.fits 
 3 -- ft950729_2235_0800S100902M.fits 
 4 -- ft950729_2235_0800S101102M.fits 
 5 -- ft950729_2235_0800S101302M.fits 
 6 -- ft950729_2235_0800S101602M.fits 
 7 -- ft950729_2235_0800S102002M.fits 
 8 -- ft950729_2235_0800S102202M.fits 
 9 -- ft950729_2235_0800S102402M.fits 
 10 -- ft950729_2235_0800S102702M.fits 
 11 -- ft950729_2235_0800S103102M.fits 
 12 -- ft950729_2235_0800S103302M.fits 
 13 -- ft950729_2235_0800S103702M.fits 
 14 -- ft950729_2235_0800S103902M.fits 
 15 -- ft950729_2235_0800S104502M.fits 
 16 -- ft950729_2235_0800S105202M.fits 
 17 -- ft950729_2235_0800S105602M.fits 
 18 -- ft950729_2235_0800S106702M.fits 
 19 -- ft950729_2235_0800S107502M.fits 
 20 -- ft950729_2235_0800S108202M.fits 
 21 -- ft950729_2235_0800S108602M.fits 
 22 -- ft950729_2235_0800S109002M.fits 
 23 -- ft950729_2235_0800S109702M.fits 
 24 -- ft950729_2235_0800S110402M.fits 
 25 -- ft950729_2235_0800S110602M.fits 
 26 -- ft950729_2235_0800S111102M.fits 
 27 -- ft950729_2235_0800S111502M.fits 
 28 -- ft950729_2235_0800S111902M.fits 
 29 -- ft950729_2235_0800S112302M.fits 
 30 -- ft950729_2235_0800S112702M.fits 
 31 -- ft950729_2235_0800S112902M.fits 
 32 -- ft950729_2235_0800S113502M.fits 
 33 -- ft950729_2235_0800S113702M.fits 
 34 -- ft950729_2235_0800S113902M.fits 
 35 -- ft950729_2235_0800S114902M.fits 
 36 -- ft950729_2235_0800S115302M.fits 
 37 -- ft950729_2235_0800S116002M.fits 
 38 -- ft950729_2235_0800S116402M.fits 
 39 -- ft950729_2235_0800S116902M.fits 
 40 -- ft950729_2235_0800S117502M.fits 
 41 -- ft950729_2235_0800S117802M.fits 
 42 -- ft950729_2235_0800S118402M.fits 
 43 -- ft950729_2235_0800S118702M.fits 
 44 -- ft950729_2235_0800S119102M.fits 
 45 -- ft950729_2235_0800S120002M.fits 
 46 -- ft950729_2235_0800S120202M.fits 
 47 -- ft950729_2235_0800S120802M.fits 
 48 -- ft950729_2235_0800S121002M.fits 
 49 -- ft950729_2235_0800S121402M.fits 
 50 -- ft950729_2235_0800S121602M.fits 
 51 -- ft950729_2235_0800S121902M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Creating ad63007000s100302l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  33  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S100202L.fits 
 2 -- ft950729_2235_0800S100402L.fits 
 3 -- ft950729_2235_0800S100602L.fits 
 4 -- ft950729_2235_0800S100802L.fits 
 5 -- ft950729_2235_0800S101002L.fits 
 6 -- ft950729_2235_0800S101702L.fits 
 7 -- ft950729_2235_0800S101902L.fits 
 8 -- ft950729_2235_0800S102302L.fits 
 9 -- ft950729_2235_0800S102802L.fits 
 10 -- ft950729_2235_0800S103202L.fits 
 11 -- ft950729_2235_0800S103802L.fits 
 12 -- ft950729_2235_0800S104402L.fits 
 13 -- ft950729_2235_0800S105502L.fits 
 14 -- ft950729_2235_0800S105902L.fits 
 15 -- ft950729_2235_0800S106502L.fits 
 16 -- ft950729_2235_0800S108102L.fits 
 17 -- ft950729_2235_0800S108702L.fits 
 18 -- ft950729_2235_0800S108902L.fits 
 19 -- ft950729_2235_0800S109402L.fits 
 20 -- ft950729_2235_0800S110302L.fits 
 21 -- ft950729_2235_0800S111002L.fits 
 22 -- ft950729_2235_0800S112802L.fits 
 23 -- ft950729_2235_0800S113602L.fits 
 24 -- ft950729_2235_0800S115002L.fits 
 25 -- ft950729_2235_0800S115202L.fits 
 26 -- ft950729_2235_0800S115402L.fits 
 27 -- ft950729_2235_0800S115602L.fits 
 28 -- ft950729_2235_0800S118502L.fits 
 29 -- ft950729_2235_0800S119202L.fits 
 30 -- ft950729_2235_0800S120102L.fits 
 31 -- ft950729_2235_0800S120402L.fits 
 32 -- ft950729_2235_0800S120902L.fits 
 33 -- ft950729_2235_0800S121502L.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S100202L.fits 
 2 -- ft950729_2235_0800S100402L.fits 
 3 -- ft950729_2235_0800S100602L.fits 
 4 -- ft950729_2235_0800S100802L.fits 
 5 -- ft950729_2235_0800S101002L.fits 
 6 -- ft950729_2235_0800S101702L.fits 
 7 -- ft950729_2235_0800S101902L.fits 
 8 -- ft950729_2235_0800S102302L.fits 
 9 -- ft950729_2235_0800S102802L.fits 
 10 -- ft950729_2235_0800S103202L.fits 
 11 -- ft950729_2235_0800S103802L.fits 
 12 -- ft950729_2235_0800S104402L.fits 
 13 -- ft950729_2235_0800S105502L.fits 
 14 -- ft950729_2235_0800S105902L.fits 
 15 -- ft950729_2235_0800S106502L.fits 
 16 -- ft950729_2235_0800S108102L.fits 
 17 -- ft950729_2235_0800S108702L.fits 
 18 -- ft950729_2235_0800S108902L.fits 
 19 -- ft950729_2235_0800S109402L.fits 
 20 -- ft950729_2235_0800S110302L.fits 
 21 -- ft950729_2235_0800S111002L.fits 
 22 -- ft950729_2235_0800S112802L.fits 
 23 -- ft950729_2235_0800S113602L.fits 
 24 -- ft950729_2235_0800S115002L.fits 
 25 -- ft950729_2235_0800S115202L.fits 
 26 -- ft950729_2235_0800S115402L.fits 
 27 -- ft950729_2235_0800S115602L.fits 
 28 -- ft950729_2235_0800S118502L.fits 
 29 -- ft950729_2235_0800S119202L.fits 
 30 -- ft950729_2235_0800S120102L.fits 
 31 -- ft950729_2235_0800S120402L.fits 
 32 -- ft950729_2235_0800S120902L.fits 
 33 -- ft950729_2235_0800S121502L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Checking ft950729_2235_0800S103501H.fits
-> Creating ad63007000s100401h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  1  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft950729_2235_0800S103501H.fits 
Merging binary extension #: 2 
 1 -- ft950729_2235_0800S103501H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully!
-> Ignoring the following files containing 000000704 events
ft950729_2235_0800S100302L.fits
ft950729_2235_0800S100702L.fits
ft950729_2235_0800S101802L.fits
ft950729_2235_0800S105402L.fits
ft950729_2235_0800S115502L.fits
ft950729_2235_0800S117702L.fits
ft950729_2235_0800S118602L.fits
ft950729_2235_0800S120302L.fits
-> Ignoring the following files containing 000000628 events
ft950729_2235_0800S113802M.fits
-> Ignoring the following files containing 000000448 events
ft950729_2235_0800S107601M.fits
ft950729_2235_0800S108301M.fits
ft950729_2235_0800S109101M.fits
ft950729_2235_0800S109801M.fits
ft950729_2235_0800S110701M.fits
ft950729_2235_0800S111201M.fits
ft950729_2235_0800S111601M.fits
ft950729_2235_0800S112001M.fits
ft950729_2235_0800S112401M.fits
ft950729_2235_0800S113001M.fits
ft950729_2235_0800S117901M.fits
ft950729_2235_0800S118801M.fits
ft950729_2235_0800S121101M.fits
ft950729_2235_0800S121701M.fits
-> Ignoring the following files containing 000000189 events
ft950729_2235_0800S105001H.fits
ft950729_2235_0800S113201H.fits
ft950729_2235_0800S114601H.fits
-> Ignoring the following files containing 000000169 events
ft950729_2235_0800S107802H.fits
ft950729_2235_0800S110202H.fits
-> Ignoring the following files containing 000000144 events
ft950729_2235_0800S115701L.fits
ft950729_2235_0800S120501L.fits
-> Ignoring the following files containing 000000138 events
ft950729_2235_0800S110502M.fits
ft950729_2235_0800S114002M.fits
-> Ignoring the following files containing 000000125 events
ft950729_2235_0800S104101H.fits
-> Ignoring the following files containing 000000119 events
ft950729_2235_0800S114401H.fits
-> Ignoring the following files containing 000000047 events
ft950729_2235_0800S104801H.fits
-> Tar-ing together the leftover raw files
a ft950729_2235_0800G200370L.fits 40K
a ft950729_2235_0800G200470L.fits 40K
a ft950729_2235_0800G200670M.fits 40K
a ft950729_2235_0800G200770M.fits 40K
a ft950729_2235_0800G201270L.fits 40K
a ft950729_2235_0800G201370M.fits 40K
a ft950729_2235_0800G201470M.fits 40K
a ft950729_2235_0800G201970M.fits 40K
a ft950729_2235_0800G202570L.fits 40K
a ft950729_2235_0800G202770M.fits 40K
a ft950729_2235_0800G202870M.fits 40K
a ft950729_2235_0800G204070H.fits 40K
a ft950729_2235_0800G204170H.fits 40K
a ft950729_2235_0800G204270H.fits 40K
a ft950729_2235_0800G204770M.fits 40K
a ft950729_2235_0800G204870M.fits 40K
a ft950729_2235_0800G205270H.fits 40K
a ft950729_2235_0800G206170M.fits 40K
a ft950729_2235_0800G206270M.fits 40K
a ft950729_2235_0800G206670H.fits 40K
a ft950729_2235_0800G206870H.fits 40K
a ft950729_2235_0800G207070H.fits 40K
a ft950729_2235_0800G207170H.fits 40K
a ft950729_2235_0800G207370H.fits 40K
a ft950729_2235_0800G207570H.fits 40K
a ft950729_2235_0800G207670H.fits 147K
a ft950729_2235_0800G207870M.fits 40K
a ft950729_2235_0800G208170L.fits 40K
a ft950729_2235_0800G208370M.fits 40K
a ft950729_2235_0800G208570M.fits 40K
a ft950729_2235_0800G208870L.fits 40K
a ft950729_2235_0800G208970H.fits 40K
a ft950729_2235_0800G209170H.fits 40K
a ft950729_2235_0800G209470L.fits 40K
a ft950729_2235_0800G210070H.fits 40K
a ft950729_2235_0800G210570H.fits 40K
a ft950729_2235_0800G210670H.fits 40K
a ft950729_2235_0800G210770H.fits 40K
a ft950729_2235_0800G210870H.fits 40K
a ft950729_2235_0800G211370M.fits 40K
a ft950729_2235_0800G211570H.fits 40K
a ft950729_2235_0800G211670H.fits 40K
a ft950729_2235_0800G211770H.fits 40K
a ft950729_2235_0800G212570M.fits 40K
a ft950729_2235_0800G212770H.fits 40K
a ft950729_2235_0800G213870M.fits 40K
a ft950729_2235_0800G214070H.fits 40K
a ft950729_2235_0800G214170H.fits 40K
a ft950729_2235_0800G214270H.fits 40K
a ft950729_2235_0800G214770M.fits 40K
a ft950729_2235_0800G214970H.fits 40K
a ft950729_2235_0800G215070H.fits 40K
a ft950729_2235_0800G215170H.fits 40K
a ft950729_2235_0800G215870H.fits 40K
a ft950729_2235_0800G215970H.fits 40K
a ft950729_2235_0800G216070H.fits 40K
a ft950729_2235_0800G216170H.fits 40K
a ft950729_2235_0800G216670M.fits 40K
a ft950729_2235_0800G216770M.fits 40K
a ft950729_2235_0800G217270M.fits 40K
a ft950729_2235_0800G217470H.fits 40K
a ft950729_2235_0800G217570H.fits 40K
a ft950729_2235_0800G217670H.fits 40K
a ft950729_2235_0800G217970M.fits 40K
a ft950729_2235_0800G218070M.fits 40K
a ft950729_2235_0800G218370M.fits 40K
a ft950729_2235_0800G218570M.fits 40K
a ft950729_2235_0800G218770H.fits 40K
a ft950729_2235_0800G218870H.fits 40K
a ft950729_2235_0800G218970H.fits 40K
a ft950729_2235_0800G219370H.fits 40K
a ft950729_2235_0800G219470H.fits 40K
a ft950729_2235_0800G219570H.fits 40K
a ft950729_2235_0800G219970H.fits 40K
a ft950729_2235_0800G220070H.fits 40K
a ft950729_2235_0800G220170H.fits 40K
a ft950729_2235_0800G220570H.fits 40K
a ft950729_2235_0800G220670H.fits 40K
a ft950729_2235_0800G221470H.fits 40K
a ft950729_2235_0800G221570H.fits 40K
a ft950729_2235_0800G221670H.fits 40K
a ft950729_2235_0800G222070H.fits 40K
a ft950729_2235_0800G222170H.fits 40K
a ft950729_2235_0800G222270H.fits 40K
a ft950729_2235_0800G223270H.fits 40K
a ft950729_2235_0800G223670L.fits 40K
a ft950729_2235_0800G223770M.fits 40K
a ft950729_2235_0800G223870M.fits 40K
a ft950729_2235_0800G224170L.fits 40K
a ft950729_2235_0800G224370L.fits 40K
a ft950729_2235_0800G224570H.fits 40K
a ft950729_2235_0800G224670H.fits 40K
a ft950729_2235_0800G224770H.fits 40K
a ft950729_2235_0800G225170M.fits 40K
a ft950729_2235_0800G225670M.fits 40K
a ft950729_2235_0800G226170H.fits 40K
a ft950729_2235_0800G226570H.fits 40K
a ft950729_2235_0800G226670H.fits 40K
a ft950729_2235_0800G227970H.fits 40K
a ft950729_2235_0800G229070M.fits 40K
a ft950729_2235_0800G230470M.fits 40K
a ft950729_2235_0800G230670H.fits 40K
a ft950729_2235_0800G230770H.fits 40K
a ft950729_2235_0800G230870H.fits 40K
a ft950729_2235_0800G232070H.fits 40K
a ft950729_2235_0800G232170H.fits 40K
a ft950729_2235_0800G232370H.fits 40K
a ft950729_2235_0800G232770H.fits 40K
a ft950729_2235_0800G232870H.fits 40K
a ft950729_2235_0800G232970H.fits 40K
a ft950729_2235_0800G233870M.fits 40K
a ft950729_2235_0800G234470H.fits 40K
a ft950729_2235_0800G234570H.fits 40K
a ft950729_2235_0800G235270H.fits 40K
a ft950729_2235_0800G235370H.fits 40K
a ft950729_2235_0800G235470H.fits 40K
a ft950729_2235_0800G236070H.fits 40K
a ft950729_2235_0800G236170H.fits 40K
a ft950729_2235_0800G236270H.fits 40K
a ft950729_2235_0800G300370L.fits 40K
a ft950729_2235_0800G300470L.fits 40K
a ft950729_2235_0800G300670M.fits 40K
a ft950729_2235_0800G300770M.fits 40K
a ft950729_2235_0800G301270L.fits 40K
a ft950729_2235_0800G301370M.fits 40K
a ft950729_2235_0800G301470M.fits 40K
a ft950729_2235_0800G301970M.fits 40K
a ft950729_2235_0800G302570L.fits 40K
a ft950729_2235_0800G302770M.fits 40K
a ft950729_2235_0800G302870M.fits 40K
a ft950729_2235_0800G304070H.fits 40K
a ft950729_2235_0800G304170H.fits 40K
a ft950729_2235_0800G304270H.fits 40K
a ft950729_2235_0800G304770M.fits 40K
a ft950729_2235_0800G304870M.fits 40K
a ft950729_2235_0800G305270H.fits 40K
a ft950729_2235_0800G305970H.fits 40K
a ft950729_2235_0800G306370M.fits 40K
a ft950729_2235_0800G306470M.fits 40K
a ft950729_2235_0800G306870H.fits 40K
a ft950729_2235_0800G307070H.fits 40K
a ft950729_2235_0800G307270H.fits 40K
a ft950729_2235_0800G307470H.fits 40K
a ft950729_2235_0800G307670H.fits 40K
a ft950729_2235_0800G307870H.fits 40K
a ft950729_2235_0800G307970H.fits 40K
a ft950729_2235_0800G308270M.fits 40K
a ft950729_2235_0800G308570L.fits 40K
a ft950729_2235_0800G308770M.fits 40K
a ft950729_2235_0800G309070L.fits 40K
a ft950729_2235_0800G309170H.fits 40K
a ft950729_2235_0800G309270H.fits 40K
a ft950729_2235_0800G309370H.fits 40K
a ft950729_2235_0800G309670L.fits 40K
a ft950729_2235_0800G310370H.fits 40K
a ft950729_2235_0800G310970H.fits 40K
a ft950729_2235_0800G311070H.fits 40K
a ft950729_2235_0800G311370L.fits 40K
a ft950729_2235_0800G311570M.fits 40K
a ft950729_2235_0800G311770H.fits 40K
a ft950729_2235_0800G311870H.fits 40K
a ft950729_2235_0800G311970H.fits 40K
a ft950729_2235_0800G312770M.fits 40K
a ft950729_2235_0800G313070H.fits 40K
a ft950729_2235_0800G314170M.fits 40K
a ft950729_2235_0800G314370H.fits 40K
a ft950729_2235_0800G314470H.fits 40K
a ft950729_2235_0800G314570H.fits 40K
a ft950729_2235_0800G315070M.fits 40K
a ft950729_2235_0800G315270H.fits 40K
a ft950729_2235_0800G315370H.fits 40K
a ft950729_2235_0800G315470H.fits 40K
a ft950729_2235_0800G315670H.fits 40K
a ft950729_2235_0800G315770H.fits 40K
a ft950729_2235_0800G316370H.fits 40K
a ft950729_2235_0800G316870M.fits 40K
a ft950729_2235_0800G316970M.fits 40K
a ft950729_2235_0800G317470M.fits 40K
a ft950729_2235_0800G317670H.fits 40K
a ft950729_2235_0800G317770H.fits 40K
a ft950729_2235_0800G317870H.fits 40K
a ft950729_2235_0800G318170M.fits 40K
a ft950729_2235_0800G318270M.fits 40K
a ft950729_2235_0800G318570M.fits 40K
a ft950729_2235_0800G318770M.fits 40K
a ft950729_2235_0800G318970H.fits 40K
a ft950729_2235_0800G319070H.fits 40K
a ft950729_2235_0800G319170H.fits 40K
a ft950729_2235_0800G319570H.fits 40K
a ft950729_2235_0800G319670H.fits 40K
a ft950729_2235_0800G319770H.fits 40K
a ft950729_2235_0800G320170H.fits 40K
a ft950729_2235_0800G320270H.fits 40K
a ft950729_2235_0800G320370H.fits 40K
a ft950729_2235_0800G320870H.fits 40K
a ft950729_2235_0800G320970H.fits 40K
a ft950729_2235_0800G321670H.fits 40K
a ft950729_2235_0800G321770H.fits 40K
a ft950729_2235_0800G321870H.fits 40K
a ft950729_2235_0800G322070H.fits 40K
a ft950729_2235_0800G322270H.fits 40K
a ft950729_2235_0800G323070H.fits 40K
a ft950729_2235_0800G323470H.fits 40K
a ft950729_2235_0800G323870L.fits 40K
a ft950729_2235_0800G323970M.fits 40K
a ft950729_2235_0800G324070M.fits 40K
a ft950729_2235_0800G324370L.fits 40K
a ft950729_2235_0800G324570L.fits 40K
a ft950729_2235_0800G324770H.fits 40K
a ft950729_2235_0800G324970H.fits 40K
a ft950729_2235_0800G325370M.fits 40K
a ft950729_2235_0800G325870M.fits 40K
a ft950729_2235_0800G326370H.fits 40K
a ft950729_2235_0800G326470H.fits 40K
a ft950729_2235_0800G326870H.fits 40K
a ft950729_2235_0800G326970H.fits 40K
a ft950729_2235_0800G328270H.fits 40K
a ft950729_2235_0800G329370M.fits 40K
a ft950729_2235_0800G330770M.fits 40K
a ft950729_2235_0800G330970H.fits 40K
a ft950729_2235_0800G331070H.fits 40K
a ft950729_2235_0800G331170H.fits 40K
a ft950729_2235_0800G332370H.fits 40K
a ft950729_2235_0800G332470H.fits 40K
a ft950729_2235_0800G332670H.fits 40K
a ft950729_2235_0800G333070H.fits 40K
a ft950729_2235_0800G333170H.fits 40K
a ft950729_2235_0800G334070M.fits 40K
a ft950729_2235_0800G334770H.fits 40K
a ft950729_2235_0800G335470H.fits 40K
a ft950729_2235_0800G335570H.fits 40K
a ft950729_2235_0800G335670H.fits 40K
a ft950729_2235_0800G336370H.fits 40K
a ft950729_2235_0800G336470H.fits 40K
a ft950729_2235_0800G336770M.fits 40K
a ft950729_2235_0800G336970M.fits 40K
a ft950729_2235_0800S006001H.fits 40K
a ft950729_2235_0800S006502L.fits 43K
a ft950729_2235_0800S009301M.fits 40K
a ft950729_2235_0800S010201M.fits 40K
a ft950729_2235_0800S011201M.fits 40K
a ft950729_2235_0800S012101M.fits 40K
a ft950729_2235_0800S012602H.fits 40K
a ft950729_2235_0800S013002M.fits 40K
a ft950729_2235_0800S013201M.fits 40K
a ft950729_2235_0800S013901M.fits 40K
a ft950729_2235_0800S014501M.fits 40K
a ft950729_2235_0800S015101M.fits 40K
a ft950729_2235_0800S015701M.fits 40K
a ft950729_2235_0800S016501M.fits 40K
a ft950729_2235_0800S016701H.fits 40K
a ft950729_2235_0800S017502M.fits 60K
a ft950729_2235_0800S017702M.fits 40K
a ft950729_2235_0800S018201H.fits 40K
a ft950729_2235_0800S019701L.fits 40K
a ft950729_2235_0800S022501M.fits 40K
a ft950729_2235_0800S023601M.fits 40K
a ft950729_2235_0800S025701L.fits 43K
a ft950729_2235_0800S026501M.fits 40K
a ft950729_2235_0800S027301M.fits 40K
a ft950729_2235_0800S100302L.fits 40K
a ft950729_2235_0800S100702L.fits 43K
a ft950729_2235_0800S101802L.fits 40K
a ft950729_2235_0800S104101H.fits 43K
a ft950729_2235_0800S104801H.fits 40K
a ft950729_2235_0800S105001H.fits 43K
a ft950729_2235_0800S105402L.fits 43K
a ft950729_2235_0800S107601M.fits 40K
a ft950729_2235_0800S107802H.fits 40K
a ft950729_2235_0800S108301M.fits 40K
a ft950729_2235_0800S109101M.fits 40K
a ft950729_2235_0800S109801M.fits 40K
a ft950729_2235_0800S110202H.fits 43K
a ft950729_2235_0800S110502M.fits 40K
a ft950729_2235_0800S110701M.fits 40K
a ft950729_2235_0800S111201M.fits 40K
a ft950729_2235_0800S111601M.fits 40K
a ft950729_2235_0800S112001M.fits 40K
a ft950729_2235_0800S112401M.fits 40K
a ft950729_2235_0800S113001M.fits 40K
a ft950729_2235_0800S113201H.fits 40K
a ft950729_2235_0800S113802M.fits 57K
a ft950729_2235_0800S114002M.fits 40K
a ft950729_2235_0800S114401H.fits 43K
a ft950729_2235_0800S114601H.fits 40K
a ft950729_2235_0800S115502L.fits 43K
a ft950729_2235_0800S115701L.fits 40K
a ft950729_2235_0800S117702L.fits 40K
a ft950729_2235_0800S117901M.fits 40K
a ft950729_2235_0800S118602L.fits 43K
a ft950729_2235_0800S118801M.fits 40K
a ft950729_2235_0800S120302L.fits 40K
a ft950729_2235_0800S120501L.fits 43K
a ft950729_2235_0800S121101M.fits 40K
a ft950729_2235_0800S121701M.fits 40K
-> Checking OBJECT keywords in HK and event files

Converting FAINT mode files to BRIGHT and BRIGHT2 modes ( 22:05:34 )

-> Split threshold for SIS0=40, and SIS1=40
-> Fetching faintdfe.tbl
-> Calculating DFE values for ad63007000s000101h.unf with zerodef=1
-> Converting ad63007000s000101h.unf to ad63007000s000112h.unf
-> Calculating DFE values for ad63007000s000101h.unf with zerodef=2
-> Converting ad63007000s000101h.unf to ad63007000s000102h.unf
-> Generating corner pixel histogram ad63007000s000102h_0.cnr
-> Generating corner pixel histogram ad63007000s000102h_1.cnr
-> Generating corner pixel histogram ad63007000s000102h_2.cnr
-> Generating corner pixel histogram ad63007000s000102h_3.cnr
-> Calculating DFE values for ad63007000s000301h.unf with zerodef=1
-> Converting ad63007000s000301h.unf to ad63007000s000312h.unf
-> Calculating DFE values for ad63007000s000301h.unf with zerodef=2
-> Converting ad63007000s000301h.unf to ad63007000s000302h.unf
-> Generating corner pixel histogram ad63007000s000302h_0.cnr
-> Generating corner pixel histogram ad63007000s000302h_1.cnr
-> Generating corner pixel histogram ad63007000s000302h_2.cnr
-> Generating corner pixel histogram ad63007000s000302h_3.cnr
-> Calculating DFE values for ad63007000s000401h.unf with zerodef=1
-> Converting ad63007000s000401h.unf to ad63007000s000412h.unf
-> Calculating DFE values for ad63007000s000401h.unf with zerodef=2
-> Converting ad63007000s000401h.unf to ad63007000s000402h.unf
-> Generating corner pixel histogram ad63007000s000402h_0.cnr
-> Generating corner pixel histogram ad63007000s000402h_1.cnr
-> Generating corner pixel histogram ad63007000s000402h_2.cnr
-> Generating corner pixel histogram ad63007000s000402h_3.cnr
-> Calculating DFE values for ad63007000s100101h.unf with zerodef=1
-> Converting ad63007000s100101h.unf to ad63007000s100112h.unf
-> Calculating DFE values for ad63007000s100101h.unf with zerodef=2
-> Converting ad63007000s100101h.unf to ad63007000s100102h.unf
-> Generating corner pixel histogram ad63007000s100102h_0.cnr
-> Generating corner pixel histogram ad63007000s100102h_1.cnr
-> Generating corner pixel histogram ad63007000s100102h_2.cnr
-> Generating corner pixel histogram ad63007000s100102h_3.cnr
-> Calculating DFE values for ad63007000s100401h.unf with zerodef=1
-> Converting ad63007000s100401h.unf to ad63007000s100412h.unf
-> Calculating DFE values for ad63007000s100401h.unf with zerodef=2
-> Converting ad63007000s100401h.unf to ad63007000s100402h.unf
-> Generating corner pixel histogram ad63007000s100402h_0.cnr
-> Generating corner pixel histogram ad63007000s100402h_1.cnr
-> Generating corner pixel histogram ad63007000s100402h_2.cnr
-> Generating corner pixel histogram ad63007000s100402h_3.cnr

Creating GIS gain history file ( 23:44:51 )

-> Fetching gis_temp2gain.fits
-> Fetching leapsec.fits
-> Creating gain history file ft950729_2235_0800.ghf
-> Output from ISAS program temp2gain
temp2gain v4.2
opening ft950729_2235.0800
'ft950729_2235.0800' is successfully opened
Data Start Time is 81210900.55 (950729 223500)
Time Margin 2.0 sec included
Sync error detected in 3319 th SF
Sync error detected in 3320 th SF
Sync error detected in 3321 th SF
Sync error detected in 5612 th SF
Sync error detected in 5614 th SF
Sync error detected in 5683 th SF
Sync error detected in 5686 th SF
Sync error detected in 5687 th SF
Sync error detected in 5753 th SF
Sync error detected in 6957 th SF
Sync error detected in 7176 th SF
Sync error detected in 7223 th SF
Sync error detected in 7394 th SF
Sync error detected in 7397 th SF
Sync error detected in 7464 th SF
Sync error detected in 7473 th SF
Sync error detected in 8635 th SF
Sync error detected in 8641 th SF
Sync error detected in 8673 th SF
Sync error detected in 8674 th SF
Sync error detected in 8675 th SF
Sync error detected in 8676 th SF
Sync error detected in 8677 th SF
Sync error detected in 8678 th SF
Sync error detected in 8738 th SF
Sync error detected in 8751 th SF
Sync error detected in 8752 th SF
Sync error detected in 8753 th SF
Sync error detected in 8759 th SF
Sync error detected in 8761 th SF
Sync error detected in 8766 th SF
Sync error detected in 8767 th SF
Sync error detected in 8768 th SF
Sync error detected in 8770 th SF
Sync error detected in 8771 th SF
Sync error detected in 8773 th SF
Sync error detected in 8775 th SF
Sync error detected in 8776 th SF
Sync error detected in 8779 th SF
Sync error detected in 8781 th SF
Sync error detected in 8784 th SF
Sync error detected in 8790 th SF
Sync error detected in 8862 th SF
Sync error detected in 8864 th SF
Sync error detected in 8922 th SF
Sync error detected in 8923 th SF
Sync error detected in 8924 th SF
Sync error detected in 8925 th SF
Sync error detected in 8926 th SF
Sync error detected in 8927 th SF
Sync error detected in 8928 th SF
Sync error detected in 8933 th SF
Sync error detected in 8953 th SF
Sync error detected in 8955 th SF
Sync error detected in 8956 th SF
Sync error detected in 8959 th SF
Sync error detected in 8960 th SF
Sync error detected in 8961 th SF
Sync error detected in 8962 th SF
Sync error detected in 8968 th SF
Sync error detected in 9004 th SF
Sync error detected in 9005 th SF
Sync error detected in 9006 th SF
Sync error detected in 9007 th SF
Sync error detected in 9008 th SF
Sync error detected in 9010 th SF
Sync error detected in 9059 th SF
Sync error detected in 9060 th SF
Sync error detected in 9061 th SF
Sync error detected in 9062 th SF
Sync error detected in 9064 th SF
Sync error detected in 9196 th SF
Sync error detected in 9199 th SF
Sync error detected in 10346 th SF
Sync error detected in 14966 th SF
Sync error detected in 24923 th SF
Sync error detected in 24978 th SF
Sync error detected in 24994 th SF
Sync error detected in 24997 th SF
Sync error detected in 24998 th SF
Sync error detected in 24999 th SF
Sync error detected in 25000 th SF
Sync error detected in 25154 th SF
Sync error detected in 25222 th SF
Sync error detected in 25954 th SF
Sync error detected in 26039 th SF
Sync error detected in 26080 th SF
Sync error detected in 26143 th SF
Sync error detected in 26169 th SF
Sync error detected in 26195 th SF
Sync error detected in 26239 th SF
Sync error detected in 26266 th SF
Sync error detected in 26303 th SF
Sync error detected in 26304 th SF
Sync error detected in 26305 th SF
Sync error detected in 26323 th SF
Sync error detected in 26325 th SF
Sync error detected in 26326 th SF
Sync error detected in 26327 th SF
Sync error detected in 26333 th SF
Sync error detected in 26336 th SF
Sync error detected in 26337 th SF
Sync error detected in 26338 th SF
Sync error detected in 26339 th SF
Sync error detected in 26340 th SF
Sync error detected in 26341 th SF
Sync error detected in 26342 th SF
Sync error detected in 26343 th SF
Sync error detected in 26344 th SF
Sync error detected in 26345 th SF
Sync error detected in 26454 th SF
Sync error detected in 26455 th SF
Sync error detected in 26456 th SF
Sync error detected in 26460 th SF
Sync error detected in 26618 th SF
Sync error detected in 26635 th SF
Sync error detected in 26638 th SF
Sync error detected in 26821 th SF
Sync error detected in 37015 th SF
Sync error detected in 37016 th SF
Sync error detected in 37017 th SF
Sync error detected in 37043 th SF
Sync error detected in 37055 th SF
Sync error detected in 37199 th SF
Sync error detected in 37218 th SF
'ft950729_2235.0800' EOF detected, sf=37587
Data End Time is 81417639.89 (950801 080039)
Gain History is written in ft950729_2235_0800.ghf
-> Checking if column CAL_START in ft950729_2235_0800.ghf[1] is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Checking if column CAL_STOP in ft950729_2235_0800.ghf[1] is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED

Running ASCALIN on unfiltered event files ( 23:54:32 )

-> Checking if ad63007000g200170h.unf is covered by attitude file
-> Running ascalin on ad63007000g200170h.unf
-> Fetching gis2_ano_on_flf_180295.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g200270m.unf is covered by attitude file
-> Running ascalin on ad63007000g200270m.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81410691.409725
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g200370l.unf is covered by attitude file
-> Running ascalin on ad63007000g200370l.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g200470h.unf is covered by attitude file
-> Running ascalin on ad63007000g200470h.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g200570l.unf is covered by attitude file
-> Running ascalin on ad63007000g200570l.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g200670m.unf is covered by attitude file
-> Running ascalin on ad63007000g200670m.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300170h.unf is covered by attitude file
-> Running ascalin on ad63007000g300170h.unf
-> Fetching gis3_ano_on_flf_180295.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300270m.unf is covered by attitude file
-> Running ascalin on ad63007000g300270m.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81410691.409725
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300370l.unf is covered by attitude file
-> Running ascalin on ad63007000g300370l.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300470h.unf is covered by attitude file
-> Running ascalin on ad63007000g300470h.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300570l.unf is covered by attitude file
-> Running ascalin on ad63007000g300570l.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000g300670m.unf is covered by attitude file
-> Running ascalin on ad63007000g300670m.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000101h.unf is covered by attitude file
-> Running ascalin on ad63007000s000101h.unf
-> Fetching sisph2pi_110397.fits
-> Fetching s0_teldef_ascalin.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000102h.unf is covered by attitude file
-> Running ascalin on ad63007000s000102h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000112h.unf is covered by attitude file
-> Running ascalin on ad63007000s000112h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000202m.unf is covered by attitude file
-> Running ascalin on ad63007000s000202m.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81410691.409725
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000301h.unf is covered by attitude file
-> Running ascalin on ad63007000s000301h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000302h.unf is covered by attitude file
-> Running ascalin on ad63007000s000302h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000312h.unf is covered by attitude file
-> Running ascalin on ad63007000s000312h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000401h.unf is covered by attitude file
-> Running ascalin on ad63007000s000401h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000402h.unf is covered by attitude file
-> Running ascalin on ad63007000s000402h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000412h.unf is covered by attitude file
-> Running ascalin on ad63007000s000412h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000502l.unf is covered by attitude file
-> Running ascalin on ad63007000s000502l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000602m.unf is covered by attitude file
-> Running ascalin on ad63007000s000602m.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81410691.409725
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000702l.unf is covered by attitude file
-> Running ascalin on ad63007000s000702l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s000802l.unf is covered by attitude file
-> Running ascalin on ad63007000s000802l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100101h.unf is covered by attitude file
-> Running ascalin on ad63007000s100101h.unf
-> sisph2pi_110397.fits already present in current directory
-> Fetching s1_teldef_ascalin.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100102h.unf is covered by attitude file
-> Running ascalin on ad63007000s100102h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100112h.unf is covered by attitude file
-> Running ascalin on ad63007000s100112h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100202m.unf is covered by attitude file
-> Running ascalin on ad63007000s100202m.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81410691.409725
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100302l.unf is covered by attitude file
-> Running ascalin on ad63007000s100302l.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81261383.885720
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81330293.665119
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81347584.110340
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    81349936.102813
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad63007000s100401h.unf is covered by attitude file
-> Running ascalin on ad63007000s100401h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad63007000s100402h.unf is covered by attitude file
-> Running ascalin on ad63007000s100402h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad63007000s100412h.unf is covered by attitude file
-> Running ascalin on ad63007000s100412h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t

Creating filter files ( 02:17:45 )

-> Fetching rigidity.data.1.23
-> leapsec.fits already present in current directory
-> Making filter file ft950729_2235_0800.mkf
-> Standard Output From FTOOL mkfilter2:
Date and time are: 95/ 7/29 22:35  mjd=49927.940972 
Orbit file name is ./frf.orbit.213
Epoch of Orbital Elements: 1995/7/24 23:0:0
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa950729_2235.0800
S0-HK file: ft950729_2235_0800S0HK.fits
S1-HK file: ft950729_2235_0800S1HK.fits
G2-HK file: ft950729_2235_0800G2HK.fits
G3-HK file: ft950729_2235_0800G3HK.fits
output FITS File: ft950729_2235_0800.mkf
Total 6462 Data bins were processed.
-> Checking if column TIME in ft950729_2235_0800.mkf is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Calculating dead time values for filter file
-> Putting dark frame errors into filter files
-> Plotting quantities from ft950729_2235_0800.mkf

Cleaning and filtering the unfiltered event files ( 04:28:16 )

-> Skipping ad63007000s000101h.unf because of mode
-> Filtering ad63007000s000102h.unf into ad63007000s000102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   83327.713
 The mean of the selected column is                  53.142674
 The standard deviation of the selected column is    28.232508
 The minimum of selected column is                   13.041710
 The maximum of selected column is                   555.53308
 The number of points used in calculation is             1568
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   69172.993
 The mean of the selected column is                  44.115429
 The standard deviation of the selected column is    27.970695
 The minimum of selected column is                   11.087536
 The maximum of selected column is                   478.00156
 The number of points used in calculation is             1568
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   129922.17
 The mean of the selected column is                  83.820753
 The standard deviation of the selected column is    121.74459
 The minimum of selected column is                   15.700051
 The maximum of selected column is                   1313.7543
 The number of points used in calculation is             1550
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   85690.967
 The mean of the selected column is                  54.649851
 The standard deviation of the selected column is    61.777533
 The minimum of selected column is                   13.604212
 The maximum of selected column is                   1189.6914
 The number of points used in calculation is             1568
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<137.8 )&&
(S0_PIXL1>0.0 && S0_PIXL1<128 )&&
(S0_PIXL2>0.0 && S0_PIXL2<449 )&&
(S0_PIXL3>0.0 && S0_PIXL3<239.9 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.56E+05   708373 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         551459    463266              0     88193         0         0
 Writing events file
 463266 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        551459    463266              0     88193         0         0
   in   47221.93 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       463266
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              83      191678
 Flickering pixels iter, pixels & cnts :   1          31        2308
cleaning chip #           1
 Hot pixels & counts                   :              38       82497
 Flickering pixels iter, pixels & cnts :   1          44        1809
cleaning chip #           2
 Hot pixels & counts                   :              32       51394
 Flickering pixels iter, pixels & cnts :   1          18         599
cleaning chip #           3
 Hot pixels & counts                   :              41       86095
 Flickering pixels iter, pixels & cnts :   1          24        1861
 
 Number of pixels rejected           :          311
 Number of (internal) image counts   :       463266
 Number of image cts rejected (N, %) :       418241     90.2809601
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           114           82           50           65
 
 Image counts      :        198517       110218        60947        93584
 Image cts rejected:        193986        84306        51993        87956
 Image cts rej (%) :         97.72        76.49        85.31        93.99
 
    filtering data...
 
 Total counts      :        198517       110218        60947        93584
 Total cts rejected:        193986        84306        51993        87956
 Total cts rej (%) :         97.72        76.49        85.31        93.99
 
 Number of clean counts accepted  :        45025
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          311
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000102h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000102h.evt use_events=no
 Wrote cleaned events file to ad63007000s000102h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad63007000s000112h.unf into ad63007000s000112h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   83327.713
 The mean of the selected column is                  53.142674
 The standard deviation of the selected column is    28.232508
 The minimum of selected column is                   13.041710
 The maximum of selected column is                   555.53308
 The number of points used in calculation is             1568
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   69172.993
 The mean of the selected column is                  44.115429
 The standard deviation of the selected column is    27.970695
 The minimum of selected column is                   11.087536
 The maximum of selected column is                   478.00156
 The number of points used in calculation is             1568
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   129922.17
 The mean of the selected column is                  83.820753
 The standard deviation of the selected column is    121.74459
 The minimum of selected column is                   15.700051
 The maximum of selected column is                   1313.7543
 The number of points used in calculation is             1550
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   85690.967
 The mean of the selected column is                  54.649851
 The standard deviation of the selected column is    61.777533
 The minimum of selected column is                   13.604212
 The maximum of selected column is                   1189.6914
 The number of points used in calculation is             1568
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<137.8 )&&
(S0_PIXL1>0.0 && S0_PIXL1<128 )&&
(S0_PIXL2>0.0 && S0_PIXL2<449 )&&
(S0_PIXL3>0.0 && S0_PIXL3<239.9 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.56E+05   723651 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         596124    499951              0     96173         0         0
 Writing events file
 499951 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        596124    499951              0     96173         0         0
   in   47221.93 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       499951
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              85      207682
 Flickering pixels iter, pixels & cnts :   1          28        2103
cleaning chip #           1
 Hot pixels & counts                   :              41       86190
 Flickering pixels iter, pixels & cnts :   1          39        1519
cleaning chip #           2
 Hot pixels & counts                   :              34       56041
 Flickering pixels iter, pixels & cnts :   1          17         505
cleaning chip #           3
 Hot pixels & counts                   :              43       93779
 Flickering pixels iter, pixels & cnts :   1          24        1822
 
 Number of pixels rejected           :          311
 Number of (internal) image counts   :       499951
 Number of image cts rejected (N, %) :       449641     89.9370117
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           113           80           51           67
 
 Image counts      :        214930       116249        66732       102040
 Image cts rejected:        209785        87709        56546        95601
 Image cts rej (%) :         97.61        75.45        84.74        93.69
 
    filtering data...
 
 Total counts      :        214930       116249        66732       102040
 Total cts rejected:        209785        87709        56546        95601
 Total cts rej (%) :         97.61        75.45        84.74        93.69
 
 Number of clean counts accepted  :        50310
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          311
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000112h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad63007000s000112h.evt use_events=no
 Wrote cleaned events file to ad63007000s000112h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad63007000s000202m.unf into ad63007000s000202m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   56557.999
 The mean of the selected column is                  59.913135
 The standard deviation of the selected column is    55.008631
 The minimum of selected column is                   3.2993627
 The maximum of selected column is                   713.93976
 The number of points used in calculation is              944
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   50924.616
 The mean of the selected column is                  53.380101
 The standard deviation of the selected column is    66.303456
 The minimum of selected column is                   2.3026459
 The maximum of selected column is                   777.65869
 The number of points used in calculation is              954
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   89511.284
 The mean of the selected column is                  94.123327
 The standard deviation of the selected column is    160.42993
 The minimum of selected column is                   6.2125378
 The maximum of selected column is                   1691.0994
 The number of points used in calculation is              951
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   57656.721
 The mean of the selected column is                  60.436814
 The standard deviation of the selected column is    81.585046
 The minimum of selected column is                   2.1283028
 The maximum of selected column is                   1120.4724
 The number of points used in calculation is              954
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<224.9 )&&
(S0_PIXL1>0.0 && S0_PIXL1<252.2 )&&
(S0_PIXL2>0.0 && S0_PIXL2<575.4 )&&
(S0_PIXL3>0.0 && S0_PIXL3<305.1 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.47E+05   563461 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         435958    279211              0    156747         0         0
 Writing events file
 279211 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        435958    279211              0    156747         0         0
   in   28575.86 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       279211
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              83      114496
 Flickering pixels iter, pixels & cnts :   1          27        1569
cleaning chip #           1
 Hot pixels & counts                   :              40       50057
 Flickering pixels iter, pixels & cnts :   1          23         805
cleaning chip #           2
 Hot pixels & counts                   :              31       31504
 Flickering pixels iter, pixels & cnts :   1          19         437
cleaning chip #           3
 Hot pixels & counts                   :              42       52930
 Flickering pixels iter, pixels & cnts :   1          21        1153
 
 Number of pixels rejected           :          286
 Number of (internal) image counts   :       279211
 Number of image cts rejected (N, %) :       252951     90.5949249
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           110           63           50           63
 
 Image counts      :        118685        65695        37304        57527
 Image cts rejected:        116065        50862        31941        54083
 Image cts rej (%) :         97.79        77.42        85.62        94.01
 
    filtering data...
 
 Total counts      :        118685        65695        37304        57527
 Total cts rejected:        116065        50862        31941        54083
 Total cts rej (%) :         97.79        77.42        85.62        94.01
 
 Number of clean counts accepted  :        26260
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          286
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000202m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000202m.evt use_events=no
 Wrote cleaned events file to ad63007000s000202m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad63007000s000301h.unf because of mode
-> Filtering ad63007000s000302h.unf into ad63007000s000302h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   12762.760
 The mean of the selected column is                  386.75031
 The standard deviation of the selected column is    365.33705
 The minimum of selected column is                   46.781403
 The maximum of selected column is                   1428.5046
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   13160.355
 The mean of the selected column is                  387.06927
 The standard deviation of the selected column is    388.56227
 The minimum of selected column is                   34.750114
 The maximum of selected column is                   1495.3799
 The number of points used in calculation is               34
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   24309.412
 The mean of the selected column is                  736.64886
 The standard deviation of the selected column is    551.20747
 The minimum of selected column is                   72.843987
 The maximum of selected column is                   1973.0900
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   18718.030
 The mean of the selected column is                  567.21302
 The standard deviation of the selected column is    526.17353
 The minimum of selected column is                   43.468891
 The maximum of selected column is                   2224.6948
 The number of points used in calculation is               33
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<1482.7 )&&
(S0_PIXL1>0.0 && S0_PIXL1<1552.7 )&&
(S0_PIXL2>0.0 && S0_PIXL2<2390.2 )&&
(S0_PIXL3>0.0 && S0_PIXL3<2145.7 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.38E+04    24389 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          13943      8563              0      5380         0         0
 Writing events file
   8563 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         13943      8563              0      5380         0         0
   in    1007.30 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         8563
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              76        3398
 Flickering pixels iter, pixels & cnts :   1          39         380
cleaning chip #           1
 Hot pixels & counts                   :              43        1861
 Flickering pixels iter, pixels & cnts :   1          25         159
cleaning chip #           2
 Hot pixels & counts                   :              21         389
 Flickering pixels iter, pixels & cnts :   1           8          39
cleaning chip #           3
 Hot pixels & counts                   :              42        1295
 Flickering pixels iter, pixels & cnts :   1          23         152
 
 Number of pixels rejected           :          277
 Number of (internal) image counts   :         8563
 Number of image cts rejected (N, %) :         7673     89.6064453
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           115           68           29           65
 
 Image counts      :          3927         2519          523         1594
 Image cts rejected:          3778         2020          428         1447
 Image cts rej (%) :         96.21        80.19        81.84        90.78
 
    filtering data...
 
 Total counts      :          3927         2519          523         1594
 Total cts rejected:          3778         2020          428         1447
 Total cts rej (%) :         96.21        80.19        81.84        90.78
 
 Number of clean counts accepted  :          890
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          277
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000302h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000302h.evt use_events=no
 Wrote cleaned events file to ad63007000s000302h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad63007000s000312h.unf into ad63007000s000312h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   12762.760
 The mean of the selected column is                  386.75031
 The standard deviation of the selected column is    365.33705
 The minimum of selected column is                   46.781403
 The maximum of selected column is                   1428.5046
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   13160.355
 The mean of the selected column is                  387.06927
 The standard deviation of the selected column is    388.56227
 The minimum of selected column is                   34.750114
 The maximum of selected column is                   1495.3799
 The number of points used in calculation is               34
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   24309.412
 The mean of the selected column is                  736.64886
 The standard deviation of the selected column is    551.20747
 The minimum of selected column is                   72.843987
 The maximum of selected column is                   1973.0900
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   18718.030
 The mean of the selected column is                  567.21302
 The standard deviation of the selected column is    526.17353
 The minimum of selected column is                   43.468891
 The maximum of selected column is                   2224.6948
 The number of points used in calculation is               33
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<1482.7 )&&
(S0_PIXL1>0.0 && S0_PIXL1<1552.7 )&&
(S0_PIXL2>0.0 && S0_PIXL2<2390.2 )&&
(S0_PIXL3>0.0 && S0_PIXL3<2145.7 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.38E+04    28621 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          17119     10032              0      7087         0         0
 Writing events file
  10032 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17119     10032              0      7087         0         0
   in    1007.30 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        10032
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              79        3869
 Flickering pixels iter, pixels & cnts :   1          45         504
 Flickering pixels iter, pixels & cnts :   2           1           4
cleaning chip #           1
 Hot pixels & counts                   :              45        2164
 Flickering pixels iter, pixels & cnts :   1          24         165
cleaning chip #           2
 Hot pixels & counts                   :              24         490
 Flickering pixels iter, pixels & cnts :   1          10          41
cleaning chip #           3
 Hot pixels & counts                   :              45        1504
 Flickering pixels iter, pixels & cnts :   1          33         200
 
 Number of pixels rejected           :          306
 Number of (internal) image counts   :        10032
 Number of image cts rejected (N, %) :         8941     89.1248016
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           125           69           34           78
 
 Image counts      :          4548         2967          652         1865
 Image cts rejected:          4377         2329          531         1704
 Image cts rej (%) :         96.24        78.50        81.44        91.37
 
    filtering data...
 
 Total counts      :          4548         2967          652         1865
 Total cts rejected:          4377         2329          531         1704
 Total cts rej (%) :         96.24        78.50        81.44        91.37
 
 Number of clean counts accepted  :         1091
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          306
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000312h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad63007000s000312h.evt use_events=no
 Wrote cleaned events file to ad63007000s000312h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad63007000s000401h.unf because of mode
-> Filtering ad63007000s000402h.unf into ad63007000s000402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4764.7548
 The mean of the selected column is                  60.313352
 The standard deviation of the selected column is    16.710922
 The minimum of selected column is                   39.687626
 The maximum of selected column is                   130.56291
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3872.5853
 The mean of the selected column is                  49.020067
 The standard deviation of the selected column is    19.343744
 The minimum of selected column is                   15.760483
 The maximum of selected column is                   174.00055
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   5219.7134
 The mean of the selected column is                  66.072322
 The standard deviation of the selected column is    20.297339
 The minimum of selected column is                   36.640739
 The maximum of selected column is                   153.25049
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4323.0554
 The mean of the selected column is                  54.722221
 The standard deviation of the selected column is    18.291064
 The minimum of selected column is                   16.833405
 The maximum of selected column is                   142.81294
 The number of points used in calculation is               79
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>10.1 && S0_PIXL0<110.4 )&&
(S0_PIXL1>0.0 && S0_PIXL1<107 )&&
(S0_PIXL2>5.1 && S0_PIXL2<126.9 )&&
(S0_PIXL3>0.0 && S0_PIXL3<109.5 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.30E+04    42797 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          31793     24232              0      7561         0         0
 Writing events file
  24232 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         31793     24232              0      7561         0         0
   in    2301.77 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        24232
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              78        9571
 Flickering pixels iter, pixels & cnts :   1          20         269
cleaning chip #           1
 Hot pixels & counts                   :              39        4519
 Flickering pixels iter, pixels & cnts :   1           9         131
cleaning chip #           2
 Hot pixels & counts                   :              29        3012
 Flickering pixels iter, pixels & cnts :   1           8          55
cleaning chip #           3
 Hot pixels & counts                   :              43        4451
 Flickering pixels iter, pixels & cnts :   1          11         110
 
 Number of pixels rejected           :          237
 Number of (internal) image counts   :        24232
 Number of image cts rejected (N, %) :        22118     91.2760010
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            98           48           37           54
 
 Image counts      :         10021         5826         3544         4841
 Image cts rejected:          9840         4650         3067         4561
 Image cts rej (%) :         98.19        79.81        86.54        94.22
 
    filtering data...
 
 Total counts      :         10021         5826         3544         4841
 Total cts rejected:          9840         4650         3067         4561
 Total cts rej (%) :         98.19        79.81        86.54        94.22
 
 Number of clean counts accepted  :         2114
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          237
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000402h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000402h.evt use_events=no
 Wrote cleaned events file to ad63007000s000402h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad63007000s000412h.unf into ad63007000s000412h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4764.7548
 The mean of the selected column is                  60.313352
 The standard deviation of the selected column is    16.710922
 The minimum of selected column is                   39.687626
 The maximum of selected column is                   130.56291
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3872.5853
 The mean of the selected column is                  49.020067
 The standard deviation of the selected column is    19.343744
 The minimum of selected column is                   15.760483
 The maximum of selected column is                   174.00055
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   5219.7134
 The mean of the selected column is                  66.072322
 The standard deviation of the selected column is    20.297339
 The minimum of selected column is                   36.640739
 The maximum of selected column is                   153.25049
 The number of points used in calculation is               79
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4323.0554
 The mean of the selected column is                  54.722221
 The standard deviation of the selected column is    18.291064
 The minimum of selected column is                   16.833405
 The maximum of selected column is                   142.81294
 The number of points used in calculation is               79
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>10.1 && S0_PIXL0<110.4 )&&
(S0_PIXL1>0.0 && S0_PIXL1<107 )&&
(S0_PIXL2>5.1 && S0_PIXL2<126.9 )&&
(S0_PIXL3>0.0 && S0_PIXL3<109.5 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.30E+04    43809 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          34868     26534              0      8334         0         0
 Writing events file
  26534 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         34868     26534              0      8334         0         0
   in    2301.77 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        26534
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              83       10554
 Flickering pixels iter, pixels & cnts :   1          15         266
cleaning chip #           1
 Hot pixels & counts                   :              41        4777
 Flickering pixels iter, pixels & cnts :   1          10         102
cleaning chip #           2
 Hot pixels & counts                   :              31        3334
 Flickering pixels iter, pixels & cnts :   1          10          63
cleaning chip #           3
 Hot pixels & counts                   :              45        5002
 Flickering pixels iter, pixels & cnts :   1           9          63
 
 Number of pixels rejected           :          244
 Number of (internal) image counts   :        26534
 Number of image cts rejected (N, %) :        24161     91.0567551
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            98           51           41           54
 
 Image counts      :         11037         6168         3944         5385
 Image cts rejected:         10820         4879         3397         5065
 Image cts rej (%) :         98.03        79.10        86.13        94.06
 
    filtering data...
 
 Total counts      :         11037         6168         3944         5385
 Total cts rejected:         10820         4879         3397         5065
 Total cts rej (%) :         98.03        79.10        86.13        94.06
 
 Number of clean counts accepted  :         2373
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          244
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000412h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad63007000s000412h.evt use_events=no
 Wrote cleaned events file to ad63007000s000412h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad63007000s000502l.unf into ad63007000s000502l.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1612.0360
 The mean of the selected column is                  124.00277
 The standard deviation of the selected column is    121.52771
 The minimum of selected column is                   39.281250
 The maximum of selected column is                   434.28403
 The number of points used in calculation is               13
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&
(S0_PIXL1>0)&&
(S0_PIXL2>0.0 && S0_PIXL2<488.5 )&&
(S0_PIXL3>0)  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.62E+04    46263 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          37301       226              0     37075         0         0
 Writing events file
    226 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         37301       226              0     37075         0         0
   in      38.89 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          226
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          21          63
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          13          39
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          12          36
 
 Number of pixels rejected           :           46
 Number of (internal) image counts   :          226
 Number of image cts rejected (N, %) :          138     61.0619469
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            21           13            0           12
 
 Image counts      :            89           71            0           66
 Image cts rejected:            63           39            0           36
 Image cts rej (%) :         70.79        54.93         0.00        54.55
 
    filtering data...
 
 Total counts      :            89           71            0           66
 Total cts rejected:            63           39            0           36
 Total cts rej (%) :         70.79        54.93         0.00        54.55
 
 Number of clean counts accepted  :           88
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           46
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000502l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000502l.evt use_events=no
 Wrote cleaned events file to ad63007000s000502l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad63007000s000602m.unf into ad63007000s000602m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   14922.340
 The mean of the selected column is                  324.39870
 The standard deviation of the selected column is    312.70428
 The minimum of selected column is                   50.093910
 The maximum of selected column is                   1190.7852
 The number of points used in calculation is               46
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   14270.192
 The mean of the selected column is                  310.22156
 The standard deviation of the selected column is    317.44692
 The minimum of selected column is                   43.843895
 The maximum of selected column is                   1209.9727
 The number of points used in calculation is               46
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   24966.550
 The mean of the selected column is                  542.75109
 The standard deviation of the selected column is    430.77334
 The minimum of selected column is                   67.718971
 The maximum of selected column is                   1680.1304
 The number of points used in calculation is               46
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   21578.257
 The mean of the selected column is                  469.09255
 The standard deviation of the selected column is    434.77507
 The minimum of selected column is                   43.562641
 The maximum of selected column is                   1543.1300
 The number of points used in calculation is               46
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0.0 && S0_PIXL0<1262.5 )&&
(S0_PIXL1>0.0 && S0_PIXL1<1262.5 )&&
(S0_PIXL2>0.0 && S0_PIXL2<1835 )&&
(S0_PIXL3>0.0 && S0_PIXL3<1773.4 )  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.12E+05    18955 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           9528      4529              0      4999         0         0
 Writing events file
   4529 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9528      4529              0      4999         0         0
   in    1450.36 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         4529
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              57        1835
 Flickering pixels iter, pixels & cnts :   1          26         236
cleaning chip #           1
 Hot pixels & counts                   :              33         920
 Flickering pixels iter, pixels & cnts :   1          10          67
cleaning chip #           2
 Hot pixels & counts                   :              15         228
 Flickering pixels iter, pixels & cnts :   1           4          14
cleaning chip #           3
 Hot pixels & counts                   :              35         762
 Flickering pixels iter, pixels & cnts :   1           8          47
 
 Number of pixels rejected           :          188
 Number of (internal) image counts   :         4529
 Number of image cts rejected (N, %) :         4109     90.7264328
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            83           43           19           43
 
 Image counts      :          2132         1213          319          865
 Image cts rejected:          2071          987          242          809
 Image cts rej (%) :         97.14        81.37        75.86        93.53
 
    filtering data...
 
 Total counts      :          2132         1213          319          865
 Total cts rejected:          2071          987          242          809
 Total cts rej (%) :         97.14        81.37        75.86        93.53
 
 Number of clean counts accepted  :          420
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          188
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000602m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000602m.evt use_events=no
 Wrote cleaned events file to ad63007000s000602m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad63007000s000702l.unf into ad63007000s000702l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&
(S0_PIXL1>0)&&
(S0_PIXL2>0)&&
(S0_PIXL3>0)  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      30/07/95 00:14:30 0.19E+05     3089 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000702l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000702l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000702l.evt use_events=no
 Wrote cleaned events file to ad63007000s000702l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000702l.evt since it contains 0 events
-> Filtering ad63007000s000802l.unf into ad63007000s000802l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL0>0)&&
(S0_PIXL1>0)&&
(S0_PIXL2>0)&&
(S0_PIXL3>0)  )
&&(  (S0_SATF0<1)
   ||(S0_SATF0>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF2<1)
   ||(S0_SATF2>1))
&&(  (S0_SATF3<1)
   ||(S0_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:58:46 0.67E+04     1099 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s000802l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s000802l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad63007000s000802l.evt use_events=no
 Wrote cleaned events file to ad63007000s000802l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000802l.evt since it contains 0 events
-> Skipping ad63007000s100101h.unf because of mode
-> Filtering ad63007000s100102h.unf into ad63007000s100102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   151203.87
 The mean of the selected column is                  91.805625
 The standard deviation of the selected column is    25.484931
 The minimum of selected column is                   15.237836
 The maximum of selected column is                   279.25089
 The number of points used in calculation is             1647
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   143603.19
 The mean of the selected column is                  87.403036
 The standard deviation of the selected column is    35.513002
 The minimum of selected column is                   26.875086
 The maximum of selected column is                   630.73157
 The number of points used in calculation is             1643
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   104199.72
 The mean of the selected column is                  63.266374
 The standard deviation of the selected column is    21.294184
 The minimum of selected column is                   20.031315
 The maximum of selected column is                   405.56384
 The number of points used in calculation is             1647
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   133449.27
 The mean of the selected column is                  81.025665
 The standard deviation of the selected column is    23.104564
 The minimum of selected column is                   18.347664
 The maximum of selected column is                   346.96985
 The number of points used in calculation is             1647
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>15.3 && S1_PIXL0<168.2 )&&
(S1_PIXL1>0.0 && S1_PIXL1<193.9 )&&
(S1_PIXL2>0.0 && S1_PIXL2<127.1 )&&
(S1_PIXL3>11.7 && S1_PIXL3<150.3 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.62E+05   677667 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         472195    389657              0     82538         0         0
 Writing events file
 389657 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        472195    389657              0     82538         0         0
   in   50800.39 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       389657
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              44       88005
 Flickering pixels iter, pixels & cnts :   1          25        1578
 Flickering pixels iter, pixels & cnts :   2           1           3
cleaning chip #           1
 Hot pixels & counts                   :              50      103691
 Flickering pixels iter, pixels & cnts :   1          35        2299
 Flickering pixels iter, pixels & cnts :   2           1           3
cleaning chip #           2
 Hot pixels & counts                   :              44       89211
 Flickering pixels iter, pixels & cnts :   1          28        1578
cleaning chip #           3
 Hot pixels & counts                   :              39       66904
 Flickering pixels iter, pixels & cnts :   1          28         788
 
 Number of pixels rejected           :          295
 Number of (internal) image counts   :       389657
 Number of image cts rejected (N, %) :       354060     90.8645325
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            70           86           72           67
 
 Image counts      :         94842       112244        96481        86090
 Image cts rejected:         89586       105993        90789        67692
 Image cts rej (%) :         94.46        94.43        94.10        78.63
 
    filtering data...
 
 Total counts      :         94842       112244        96481        86090
 Total cts rejected:         89586       105993        90789        67692
 Total cts rej (%) :         94.46        94.43        94.10        78.63
 
 Number of clean counts accepted  :        35597
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          295
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100102h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad63007000s100102h.evt use_events=no
 Wrote cleaned events file to ad63007000s100102h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad63007000s100112h.unf into ad63007000s100112h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   151203.87
 The mean of the selected column is                  91.805625
 The standard deviation of the selected column is    25.484931
 The minimum of selected column is                   15.237836
 The maximum of selected column is                   279.25089
 The number of points used in calculation is             1647
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   143603.19
 The mean of the selected column is                  87.403036
 The standard deviation of the selected column is    35.513002
 The minimum of selected column is                   26.875086
 The maximum of selected column is                   630.73157
 The number of points used in calculation is             1643
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   104199.72
 The mean of the selected column is                  63.266374
 The standard deviation of the selected column is    21.294184
 The minimum of selected column is                   20.031315
 The maximum of selected column is                   405.56384
 The number of points used in calculation is             1647
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   133449.27
 The mean of the selected column is                  81.025665
 The standard deviation of the selected column is    23.104564
 The minimum of selected column is                   18.347664
 The maximum of selected column is                   346.96985
 The number of points used in calculation is             1647
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>15.3 && S1_PIXL0<168.2 )&&
(S1_PIXL1>0.0 && S1_PIXL1<193.9 )&&
(S1_PIXL2>0.0 && S1_PIXL2<127.1 )&&
(S1_PIXL3>11.7 && S1_PIXL3<150.3 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.62E+05   699349 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         556848    457844              0     99004         0         0
 Writing events file
 457844 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        556848    457844              0     99004         0         0
   in   50800.39 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       457844
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              50      105456
 Flickering pixels iter, pixels & cnts :   1          18        1313
 Flickering pixels iter, pixels & cnts :   2           1          14
cleaning chip #           1
 Hot pixels & counts                   :              55      120426
 Flickering pixels iter, pixels & cnts :   1          30        2647
 Flickering pixels iter, pixels & cnts :   2           1           3
cleaning chip #           2
 Hot pixels & counts                   :              44      101767
 Flickering pixels iter, pixels & cnts :   1          30        1943
cleaning chip #           3
 Hot pixels & counts                   :              38       80200
 Flickering pixels iter, pixels & cnts :   1          34        1262
 
 Number of pixels rejected           :          301
 Number of (internal) image counts   :       457844
 Number of image cts rejected (N, %) :       415031     90.6490021
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            69           86           74           72
 
 Image counts      :        113466       130643       110493       103242
 Image cts rejected:        106783       123076       103710        81462
 Image cts rej (%) :         94.11        94.21        93.86        78.90
 
    filtering data...
 
 Total counts      :        113466       130643       110493       103242
 Total cts rejected:        106783       123076       103710        81462
 Total cts rej (%) :         94.11        94.21        93.86        78.90
 
 Number of clean counts accepted  :        42813
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          301
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100112h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad63007000s100112h.evt use_events=no
 Wrote cleaned events file to ad63007000s100112h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad63007000s100202m.unf into ad63007000s100202m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   109189.43
 The mean of the selected column is                  110.18106
 The standard deviation of the selected column is    93.001127
 The minimum of selected column is                   1.9456320
 The maximum of selected column is                   1484.1296
 The number of points used in calculation is              991
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   105198.81
 The mean of the selected column is                  105.09371
 The standard deviation of the selected column is    91.637853
 The minimum of selected column is                   1.9075068
 The maximum of selected column is                   1386.5356
 The number of points used in calculation is             1001
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   77884.079
 The mean of the selected column is                  78.750333
 The standard deviation of the selected column is    91.881973
 The minimum of selected column is                   6.7187910
 The maximum of selected column is                   1521.2860
 The number of points used in calculation is              989
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   96443.838
 The mean of the selected column is                  97.123704
 The standard deviation of the selected column is    89.215336
 The minimum of selected column is                   1.6931880
 The maximum of selected column is                   1297.7229
 The number of points used in calculation is              993
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0.0 && S1_PIXL0<389.1 )&&
(S1_PIXL1>0.0 && S1_PIXL1<380 )&&
(S1_PIXL2>0.0 && S1_PIXL2<354.3 )&&
(S1_PIXL3>0.0 && S1_PIXL3<364.7 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.60E+05   565354 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
         383550    236529              0    147021         0         0
 Writing events file
 236529 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        383550    236529              0    147021         0         0
   in   30751.99 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       236529
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              46       56924
 Flickering pixels iter, pixels & cnts :   1          23        1003
cleaning chip #           1
 Hot pixels & counts                   :              50       60651
 Flickering pixels iter, pixels & cnts :   1          41        1416
cleaning chip #           2
 Hot pixels & counts                   :              47       55158
 Flickering pixels iter, pixels & cnts :   1          18         853
cleaning chip #           3
 Hot pixels & counts                   :              39       39472
 Flickering pixels iter, pixels & cnts :   1          20         597
 
 Number of pixels rejected           :          284
 Number of (internal) image counts   :       236529
 Number of image cts rejected (N, %) :       216074     91.3520126
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            69           91           65           59
 
 Image counts      :         61246        65666        59332        50285
 Image cts rejected:         57927        62067        56011        40069
 Image cts rej (%) :         94.58        94.52        94.40        79.68
 
    filtering data...
 
 Total counts      :         61246        65666        59332        50285
 Total cts rejected:         57927        62067        56011        40069
 Total cts rej (%) :         94.58        94.52        94.40        79.68
 
 Number of clean counts accepted  :        20455
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          284
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100202m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad63007000s100202m.evt use_events=no
 Wrote cleaned events file to ad63007000s100202m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad63007000s100302l.unf into ad63007000s100302l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL0>0)&&
(S1_PIXL1>0)&&
(S1_PIXL2>0)&&
(S1_PIXL3>0)  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF0<1)
   ||(S1_SATF0>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>64))
&&((T_SAA  <0)||(T_SAA  >64))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.32E+05    60525 1111
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          42063       203              0     41860         0         0
 Writing events file
    203 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42063       203              0     41860         0         0
   in      38.89 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          203
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          10          30
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          12          36
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          12          36
 
 Number of pixels rejected           :           34
 Number of (internal) image counts   :          203
 Number of image cts rejected (N, %) :          102     50.2463036
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            10           12            0           12
 
 Image counts      :            70           66            0           67
 Image cts rejected:            30           36            0           36
 Image cts rej (%) :         42.86        54.55         0.00        53.73
 
    filtering data...
 
 Total counts      :            70           66            0           67
 Total cts rejected:            30           36            0           36
 Total cts rej (%) :         42.86        54.55         0.00        53.73
 
 Number of clean counts accepted  :          101
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           34
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100302l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad63007000s100302l.evt use_events=no
 Wrote cleaned events file to ad63007000s100302l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad63007000s100401h.unf because of mode
-> Filtering ad63007000s100402h.unf into ad63007000s100402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2830.1339
 The mean of the selected column is                  85.761635
 The standard deviation of the selected column is    12.387566
 The minimum of selected column is                   55.625175
 The maximum of selected column is                   117.87538
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2205.4757
 The mean of the selected column is                  66.832598
 The standard deviation of the selected column is    11.924421
 The minimum of selected column is                   49.312656
 The maximum of selected column is                   103.50033
 The number of points used in calculation is               33
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>48.5 && S1_PIXL1<122.9 )&&
(S1_PIXL2>31 && S1_PIXL2<102.6 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.12E+04    13865 0110
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           9585      7989              0      1596         0         0
 Writing events file
   7989 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9585      7989              0      1596         0         0
   in    1001.72 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         7989
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              37        1799
 Flickering pixels iter, pixels & cnts :   1          11          63
cleaning chip #           1
 Hot pixels & counts                   :              40        2012
 Flickering pixels iter, pixels & cnts :   1          12          94
cleaning chip #           2
 Hot pixels & counts                   :              39        1820
 Flickering pixels iter, pixels & cnts :   1          11          77
cleaning chip #           3
 Hot pixels & counts                   :              30        1361
 Flickering pixels iter, pixels & cnts :   1           9          61
 
 Number of pixels rejected           :          189
 Number of (internal) image counts   :         7989
 Number of image cts rejected (N, %) :         7287     91.2129211
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            48           52           50           39
 
 Image counts      :          1984         2219         2020         1766
 Image cts rejected:          1862         2106         1897         1422
 Image cts rej (%) :         93.85        94.91        93.91        80.52
 
    filtering data...
 
 Total counts      :          1984         2219         2020         1766
 Total cts rejected:          1862         2106         1897         1422
 Total cts rej (%) :         93.85        94.91        93.91        80.52
 
 Number of clean counts accepted  :          702
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          189
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100402h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad63007000s100402h.evt use_events=no
 Wrote cleaned events file to ad63007000s100402h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad63007000s100412h.unf into ad63007000s100412h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2830.1339
 The mean of the selected column is                  85.761635
 The standard deviation of the selected column is    12.387566
 The minimum of selected column is                   55.625175
 The maximum of selected column is                   117.87538
 The number of points used in calculation is               33
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2205.4757
 The mean of the selected column is                  66.832598
 The standard deviation of the selected column is    11.924421
 The minimum of selected column is                   49.312656
 The maximum of selected column is                   103.50033
 The number of points used in calculation is               33
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL1>48.5 && S1_PIXL1<122.9 )&&
(S1_PIXL2>31 && S1_PIXL2<102.6 )  )
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF2<1)
   ||(S1_SATF2>1))
&&(  (S1_SATF1<1)
   ||(S1_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>32))
&&((T_SAA  <0)||(T_SAA  >32))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.12E+04    14324 0110
 
Processing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
          11340      9464              0      1876         0         0
 Writing events file
   9464 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11340      9464              0      1876         0         0
   in    1001.72 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data19/seq_proc/63007000.004/screen_in_event.xsl
    reading data file: /data/data19/seq_proc/63007000.004/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         9464
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              43        2190
 Flickering pixels iter, pixels & cnts :   1           9          64
cleaning chip #           1
 Hot pixels & counts                   :              45        2348
 Flickering pixels iter, pixels & cnts :   1          15         113
cleaning chip #           2
 Hot pixels & counts                   :              41        2124
 Flickering pixels iter, pixels & cnts :   1          12          75
cleaning chip #           3
 Hot pixels & counts                   :              33        1659
 Flickering pixels iter, pixels & cnts :   1           8          56
 
 Number of pixels rejected           :          206
 Number of (internal) image counts   :         9464
 Number of image cts rejected (N, %) :         8629     91.1770935
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            52           60           53           41
 
 Image counts      :          2408         2591         2337         2128
 Image cts rejected:          2254         2461         2199         1715
 Image cts rej (%) :         93.60        94.98        94.09        80.59
 
    filtering data...
 
 Total counts      :          2408         2591         2337         2128
 Total cts rejected:          2254         2461         2199         1715
 Total cts rej (%) :         93.60        94.98        94.09        80.59
 
 Number of clean counts accepted  :          835
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          206
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000s100412h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad63007000s100412h.evt use_events=no
 Wrote cleaned events file to ad63007000s100412h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad63007000g200170h.unf into ad63007000g200170h.evt
-> Fetching GIS2_REGION256.4
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          99435     57786          33127      8522         0         0
 Writing events file
  57786 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         99435     57786          33127      8522         0         0
   in   52066.59 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200170h.evt use_events=no
Wrote events list to file ad63007000g200170h.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad63007000g200270m.unf into ad63007000g200270m.evt
-> GIS2_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          80521     38105          33052      9364         0         0
 Writing events file
  38105 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         80521     38105          33052      9364         0         0
   in   34212.32 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200270m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200270m.evt use_events=no
Wrote events list to file ad63007000g200270m.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad63007000g200370l.unf into ad63007000g200370l.evt
-> GIS2_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          19133       452          13213      5468         0         0
 Writing events file
    452 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         19133       452          13213      5468         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200370l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200370l.evt use_events=no
Wrote events list to file ad63007000g200370l.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad63007000g200470h.unf into ad63007000g200470h.evt
-> GIS2_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1508       988            519         1         0         0
 Writing events file
    988 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1508       988            519         1         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200470h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200470h.evt use_events=no
Wrote events list to file ad63007000g200470h.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad63007000g200570l.unf into ad63007000g200570l.evt
-> GIS2_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1422      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g200570l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200570l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200570l.evt use_events=no
Wrote events list to file ad63007000g200570l.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200570l.evt since it contains 0 events
-> Filtering ad63007000g200670m.unf into ad63007000g200670m.evt
-> GIS2_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      782      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            782       458            299        25         0         0
 Writing events file
    458 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           782       458            299        25         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g200670m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > save events outfile=ad63007000g200670m.evt use_events=no
Wrote events list to file ad63007000g200670m.evt
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad63007000g300170h.unf into ad63007000g300170h.evt
-> Fetching GIS3_REGION256.4
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102159     62398          29177     10584         0         0
 Writing events file
  62398 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        102159     62398          29177     10584         0         0
   in   53010.41 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300170h.evt use_events=no
Wrote events list to file ad63007000g300170h.evt
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad63007000g300270m.unf into ad63007000g300270m.evt
-> GIS3_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          78760     40584          27925     10251         0         0
 Writing events file
  40584 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         78760     40584          27925     10251         0         0
   in   34164.12 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300270m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300270m.evt use_events=no
Wrote events list to file ad63007000g300270m.evt
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad63007000g300370l.unf into ad63007000g300370l.evt
-> GIS3_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          17963       518          11362      6083         0         0
 Writing events file
    518 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17963       518          11362      6083         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300370l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300370l.evt use_events=no
Wrote events list to file ad63007000g300370l.evt
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad63007000g300470h.unf into ad63007000g300470h.evt
-> GIS3_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1558      1130            428         0         0         0
 Writing events file
   1130 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1558      1130            428         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300470h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300470h.evt use_events=no
Wrote events list to file ad63007000g300470h.evt
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad63007000g300570l.unf into ad63007000g300570l.evt
-> GIS3_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1329      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g300570l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300570l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300570l.evt use_events=no
Wrote events list to file ad63007000g300570l.evt
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300570l.evt since it contains 0 events
-> Filtering ad63007000g300670m.unf into ad63007000g300670m.evt
-> GIS3_REGION256.4 already present in current directory
-> Skipping gisclean since RISEBINS=1
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      850      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            850       516            303        31         0         0
 Writing events file
    516 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           850       516            303        31         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!screen:ASCA > read events ad63007000g300670m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > save events outfile=ad63007000g300670m.evt use_events=no
Wrote events list to file ad63007000g300670m.evt
!screen:ASCA-GIS3-PH > exit save_session=no

Generating images and exposure maps ( 07:24:36 )

-> Generating exposure map ad63007000g200170h.expo
-> GIS2_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(167.5,220,24.66,28.95,245.298)
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g200170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g200170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6266
 Mean   RA/DEC/ROLL :       10.7100      41.3358     306.6266
 Pnt    RA/DEC/ROLL :       10.6906      41.3788     306.6266
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :           232
 Total GTI (secs)   :     52066.613
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     6185.4306641    6185.4306641
  20 Percent Complete: Total/live time:    11629.9414062   11629.9414062
  30 Percent Complete: Total/live time:    16226.6162109   16226.6162109
  40 Percent Complete: Total/live time:    22666.8867188   22666.8867188
  50 Percent Complete: Total/live time:    26577.3632812   26577.3632812
  60 Percent Complete: Total/live time:    31981.8339844   31981.8339844
  70 Percent Complete: Total/live time:    37214.3085938   37214.3085938
  80 Percent Complete: Total/live time:    43757.2460938   43757.2460938
  90 Percent Complete: Total/live time:    47668.7343750   47668.7343750
 100 Percent Complete: Total/live time:    52066.6093750   52066.6093750
 
 Number of attitude steps  used:          109
 Number of attitude steps avail:       125392
 Mean RA/DEC pixel offset:      -11.9342      -3.3935
 
    writing expo file: ad63007000g200170h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g200170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g200170h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     57299            487         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786     57299            487         0         0         0
   in   52066.59 seconds
 Image            has    57299 counts for  1.100     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     26929            487         0         0     30370
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786     26929            487         0         0     30370
   in   52066.59 seconds
 Image            has    26929 counts for 0.5172     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     31288            487         0         0     26011
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786     31288            487         0         0     26011
   in   52066.59 seconds
 Image            has    31288 counts for 0.6009     counts/sec
 Command not found; type ? for a command listing
!ad63007000g200170h:ASCA >
!ad63007000g200170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g200170h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g200170h:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g200170h:ASCA-GIS2-PH > set image sky
!ad63007000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad63007000g200170h:ASCA-GIS2-PH > extract image
!ad63007000g200170h:ASCA-GIS2-PH > save image outfile=ad63007000g200170h.img
Wrote image to file ad63007000g200170h.img
!ad63007000g200170h:ASCA-GIS2-PH > filter pha_cut 0 42
!ad63007000g200170h:ASCA-GIS2-PH > extract image
!ad63007000g200170h:ASCA-GIS2-PH > save image outfile=ad63007000g200170h_lo.img
Wrote image to file ad63007000g200170h_lo.img
!ad63007000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad63007000g200170h:ASCA-GIS2-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g200170h:ASCA-GIS2-PH > extract image
!ad63007000g200170h:ASCA-GIS2-PH > save image outfile=ad63007000g200170h_hi.img
Wrote image to file ad63007000g200170h_hi.img
!ad63007000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad63007000g200270m.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g200270m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g200270m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6266
 Mean   RA/DEC/ROLL :       10.7104      41.3361     306.6266
 Pnt    RA/DEC/ROLL :       10.6896      41.3792     306.6266
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :            68
 Total GTI (secs)   :     34212.320
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     3794.0065918    3794.0065918
  20 Percent Complete: Total/live time:     7424.1308594    7424.1308594
  30 Percent Complete: Total/live time:    11350.4541016   11350.4541016
  40 Percent Complete: Total/live time:    14080.6494141   14080.6494141
  50 Percent Complete: Total/live time:    17824.9804688   17824.9804688
  60 Percent Complete: Total/live time:    21266.0175781   21266.0175781
  70 Percent Complete: Total/live time:    24401.4960938   24401.4960938
  80 Percent Complete: Total/live time:    27836.5722656   27836.5722656
  90 Percent Complete: Total/live time:    31222.3203125   31222.3203125
 100 Percent Complete: Total/live time:    34212.3164062   34212.3164062
 
 Number of attitude steps  used:          103
 Number of attitude steps avail:        41956
 Mean RA/DEC pixel offset:      -17.3016      -3.3154
 
    writing expo file: ad63007000g200270m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g200270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g200270m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105     37796            309         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105     37796            309         0         0         0
   in   34212.32 seconds
 Image            has    37796 counts for  1.105     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105     17453            309         0         0     20343
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105     17453            309         0         0     20343
   in   34212.32 seconds
 Image            has    17453 counts for 0.5101     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105     20926            309         0         0     16870
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105     20926            309         0         0     16870
   in   34212.32 seconds
 Image            has    20926 counts for 0.6117     counts/sec
 Command not found; type ? for a command listing
!ad63007000g200270m:ASCA >
!ad63007000g200270m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g200270m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g200270m:ASCA > read events ad63007000g200270m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g200270m:ASCA-GIS2-PH > set image sky
!ad63007000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad63007000g200270m:ASCA-GIS2-PH > extract image
!ad63007000g200270m:ASCA-GIS2-PH > save image outfile=ad63007000g200270m.img
Wrote image to file ad63007000g200270m.img
!ad63007000g200270m:ASCA-GIS2-PH > filter pha_cut 0 42
!ad63007000g200270m:ASCA-GIS2-PH > extract image
!ad63007000g200270m:ASCA-GIS2-PH > save image outfile=ad63007000g200270m_lo.img
Wrote image to file ad63007000g200270m_lo.img
!ad63007000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad63007000g200270m:ASCA-GIS2-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g200270m:ASCA-GIS2-PH > extract image
!ad63007000g200270m:ASCA-GIS2-PH > save image outfile=ad63007000g200270m_hi.img
Wrote image to file ad63007000g200270m_hi.img
!ad63007000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad63007000g200370l.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g200370l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g200370l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6265
 Mean   RA/DEC/ROLL :       10.7079      41.3370     306.6265
 Pnt    RA/DEC/ROLL :       10.6873      41.3834     306.6265
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :             5
 Total GTI (secs)   :       415.726
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       64.0000000      64.0000000
  20 Percent Complete: Total/live time:      128.0000000     128.0000000
  30 Percent Complete: Total/live time:      141.8986664     141.8986664
  40 Percent Complete: Total/live time:      221.8983154     221.8983154
  50 Percent Complete: Total/live time:      221.8983154     221.8983154
  60 Percent Complete: Total/live time:      320.2124329     320.2124329
  70 Percent Complete: Total/live time:      320.2124329     320.2124329
  80 Percent Complete: Total/live time:      415.7261047     415.7261047
 100 Percent Complete: Total/live time:      415.7261047     415.7261047
 
 Number of attitude steps  used:            9
 Number of attitude steps avail:         5319
 Mean RA/DEC pixel offset:      -10.1371      -2.8992
 
    writing expo file: ad63007000g200370l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g200370l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g200370l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452       447              5         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452       447              5         0         0         0
   in     415.73 seconds
 Image            has      447 counts for  1.075     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452       229              5         0         0       218
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452       229              5         0         0       218
   in     415.73 seconds
 Image            has      229 counts for 0.5508     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452       225              5         0         0       222
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452       225              5         0         0       222
   in     415.73 seconds
 Image            has      225 counts for 0.5412     counts/sec
 Command not found; type ? for a command listing
!ad63007000g200370l:ASCA >
!ad63007000g200370l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g200370l:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g200370l:ASCA > read events ad63007000g200370l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g200370l:ASCA-GIS2-PH > set image sky
!ad63007000g200370l:ASCA-GIS2-PH > filter region corner_point.reg
!ad63007000g200370l:ASCA-GIS2-PH > extract image
!ad63007000g200370l:ASCA-GIS2-PH > save image outfile=ad63007000g200370l.img
Wrote image to file ad63007000g200370l.img
!ad63007000g200370l:ASCA-GIS2-PH > filter pha_cut 0 42
!ad63007000g200370l:ASCA-GIS2-PH > extract image
!ad63007000g200370l:ASCA-GIS2-PH > save image outfile=ad63007000g200370l_lo.img
Wrote image to file ad63007000g200370l_lo.img
!ad63007000g200370l:ASCA-GIS2-PH > clear pha_cut
!ad63007000g200370l:ASCA-GIS2-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g200370l:ASCA-GIS2-PH > extract image
!ad63007000g200370l:ASCA-GIS2-PH > save image outfile=ad63007000g200370l_hi.img
Wrote image to file ad63007000g200370l_hi.img
!ad63007000g200370l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad63007000g200470h.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g200470h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g200470h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6257
 Mean   RA/DEC/ROLL :       10.7060      41.3377     306.6257
 Pnt    RA/DEC/ROLL :       10.6932      41.3801     306.6257
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :             5
 Total GTI (secs)   :       981.997
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      517.9982910     517.9982910
  20 Percent Complete: Total/live time:      517.9982910     517.9982910
  30 Percent Complete: Total/live time:      981.9968262     981.9968262
 100 Percent Complete: Total/live time:      981.9968262     981.9968262
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         2249
 Mean RA/DEC pixel offset:       -7.0407      -2.5853
 
    writing expo file: ad63007000g200470h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g200470h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g200470h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       983              5         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988       983              5         0         0         0
   in     982.00 seconds
 Image            has      983 counts for  1.001     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       449              5         0         0       534
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988       449              5         0         0       534
   in     982.00 seconds
 Image            has      449 counts for 0.4572     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       547              5         0         0       436
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988       547              5         0         0       436
   in     982.00 seconds
 Image            has      547 counts for 0.5570     counts/sec
 Command not found; type ? for a command listing
!ad63007000g200470h:ASCA >
!ad63007000g200470h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g200470h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g200470h:ASCA > read events ad63007000g200470h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g200470h:ASCA-GIS2-PH > set image sky
!ad63007000g200470h:ASCA-GIS2-PH > filter region corner_point.reg
!ad63007000g200470h:ASCA-GIS2-PH > extract image
!ad63007000g200470h:ASCA-GIS2-PH > save image outfile=ad63007000g200470h.img
Wrote image to file ad63007000g200470h.img
!ad63007000g200470h:ASCA-GIS2-PH > filter pha_cut 0 42
!ad63007000g200470h:ASCA-GIS2-PH > extract image
!ad63007000g200470h:ASCA-GIS2-PH > save image outfile=ad63007000g200470h_lo.img
Wrote image to file ad63007000g200470h_lo.img
!ad63007000g200470h:ASCA-GIS2-PH > clear pha_cut
!ad63007000g200470h:ASCA-GIS2-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g200470h:ASCA-GIS2-PH > extract image
!ad63007000g200470h:ASCA-GIS2-PH > save image outfile=ad63007000g200470h_hi.img
Wrote image to file ad63007000g200470h_hi.img
!ad63007000g200470h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad63007000g200670m.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g200670m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g200670m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6265
 Mean   RA/DEC/ROLL :       10.7097      41.3365     306.6265
 Pnt    RA/DEC/ROLL :       10.6889      41.3809     306.6265
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :            15
 Total GTI (secs)   :       431.999
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       48.0000000      48.0000000
  20 Percent Complete: Total/live time:       93.9997635      93.9997635
  30 Percent Complete: Total/live time:      143.9998474     143.9998474
  40 Percent Complete: Total/live time:      189.9997711     189.9997711
  50 Percent Complete: Total/live time:      221.9996033     221.9996033
  60 Percent Complete: Total/live time:      271.9996338     271.9996338
  70 Percent Complete: Total/live time:      335.9995117     335.9995117
  80 Percent Complete: Total/live time:      367.9994507     367.9994507
  90 Percent Complete: Total/live time:      399.9993896     399.9993896
 100 Percent Complete: Total/live time:      431.9993286     431.9993286
 
 Number of attitude steps  used:           23
 Number of attitude steps avail:         5960
 Mean RA/DEC pixel offset:      -11.4335      -3.0249
 
    writing expo file: ad63007000g200670m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g200670m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       455              3         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458       455              3         0         0         0
   in     432.00 seconds
 Image            has      455 counts for  1.053     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       195              3         0         0       260
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458       195              3         0         0       260
   in     432.00 seconds
 Image            has      195 counts for 0.4514     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       263              3         0         0       192
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458       263              3         0         0       192
   in     432.00 seconds
 Image            has      263 counts for 0.6088     counts/sec
 Command not found; type ? for a command listing
!ad63007000g200670m:ASCA >
!ad63007000g200670m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g200670m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g200670m:ASCA > read events ad63007000g200670m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g200670m:ASCA-GIS2-PH > set image sky
!ad63007000g200670m:ASCA-GIS2-PH > filter region corner_point.reg
!ad63007000g200670m:ASCA-GIS2-PH > extract image
!ad63007000g200670m:ASCA-GIS2-PH > save image outfile=ad63007000g200670m.img
Wrote image to file ad63007000g200670m.img
!ad63007000g200670m:ASCA-GIS2-PH > filter pha_cut 0 42
!ad63007000g200670m:ASCA-GIS2-PH > extract image
!ad63007000g200670m:ASCA-GIS2-PH > save image outfile=ad63007000g200670m_lo.img
Wrote image to file ad63007000g200670m_lo.img
!ad63007000g200670m:ASCA-GIS2-PH > clear pha_cut
!ad63007000g200670m:ASCA-GIS2-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g200670m:ASCA-GIS2-PH > extract image
!ad63007000g200670m:ASCA-GIS2-PH > save image outfile=ad63007000g200670m_hi.img
Wrote image to file ad63007000g200670m_hi.img
!ad63007000g200670m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad63007000g300170h.expo
-> GIS3_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(217,95,21.56,25.92,169.216)
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g300170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g300170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6154
 Mean   RA/DEC/ROLL :       10.6931      41.3570     306.6154
 Pnt    RA/DEC/ROLL :       10.7077      41.3574     306.6154
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :           240
 Total GTI (secs)   :     53010.430
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     6185.4306641    6185.4306641
  20 Percent Complete: Total/live time:    11627.9414062   11627.9414062
  30 Percent Complete: Total/live time:    16595.9316406   16595.9316406
  40 Percent Complete: Total/live time:    23616.7031250   23616.7031250
  50 Percent Complete: Total/live time:    27227.0234375   27227.0234375
  60 Percent Complete: Total/live time:    32931.6484375   32931.6484375
  70 Percent Complete: Total/live time:    37746.6250000   37746.6250000
  80 Percent Complete: Total/live time:    42991.5664062   42991.5664062
  90 Percent Complete: Total/live time:    48269.0507812   48269.0507812
 100 Percent Complete: Total/live time:    53010.4218750   53010.4218750
 
 Number of attitude steps  used:          111
 Number of attitude steps avail:       129223
 Mean RA/DEC pixel offset:       -0.0045      -2.2059
 
    writing expo file: ad63007000g300170h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g300170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g300170h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     61987            411         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398     61987            411         0         0         0
   in   53010.41 seconds
 Image            has    61987 counts for  1.169     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     29130            411         0         0     32857
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398     29130            411         0         0     32857
   in   53010.41 seconds
 Image            has    29130 counts for 0.5495     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     33760            411         0         0     28227
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398     33760            411         0         0     28227
   in   53010.41 seconds
 Image            has    33760 counts for 0.6369     counts/sec
 Command not found; type ? for a command listing
!ad63007000g300170h:ASCA >
!ad63007000g300170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g300170h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g300170h:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g300170h:ASCA-GIS3-PH > set image sky
!ad63007000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad63007000g300170h:ASCA-GIS3-PH > extract image
!ad63007000g300170h:ASCA-GIS3-PH > save image outfile=ad63007000g300170h.img
Wrote image to file ad63007000g300170h.img
!ad63007000g300170h:ASCA-GIS3-PH > filter pha_cut 0 42
!ad63007000g300170h:ASCA-GIS3-PH > extract image
!ad63007000g300170h:ASCA-GIS3-PH > save image outfile=ad63007000g300170h_lo.img
Wrote image to file ad63007000g300170h_lo.img
!ad63007000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad63007000g300170h:ASCA-GIS3-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g300170h:ASCA-GIS3-PH > extract image
!ad63007000g300170h:ASCA-GIS3-PH > save image outfile=ad63007000g300170h_hi.img
Wrote image to file ad63007000g300170h_hi.img
!ad63007000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad63007000g300270m.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g300270m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g300270m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6154
 Mean   RA/DEC/ROLL :       10.6934      41.3574     306.6154
 Pnt    RA/DEC/ROLL :       10.7066      41.3579     306.6154
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :            68
 Total GTI (secs)   :     34164.117
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     3794.0065918    3794.0065918
  20 Percent Complete: Total/live time:     7424.1308594    7424.1308594
  30 Percent Complete: Total/live time:    11350.4541016   11350.4541016
  40 Percent Complete: Total/live time:    14080.4462891   14080.4462891
  50 Percent Complete: Total/live time:    17824.7773438   17824.7773438
  60 Percent Complete: Total/live time:    21266.3144531   21266.3144531
  70 Percent Complete: Total/live time:    24401.7929688   24401.7929688
  80 Percent Complete: Total/live time:    27836.8691406   27836.8691406
  90 Percent Complete: Total/live time:    31222.1171875   31222.1171875
 100 Percent Complete: Total/live time:    34164.1132812   34164.1132812
 
 Number of attitude steps  used:          103
 Number of attitude steps avail:        41956
 Mean RA/DEC pixel offset:       -5.2229      -2.1155
 
    writing expo file: ad63007000g300270m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g300270m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g300270m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584     40308            276         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584     40308            276         0         0         0
   in   34164.12 seconds
 Image            has    40308 counts for  1.180     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584     18874            276         0         0     21434
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584     18874            276         0         0     21434
   in   34164.12 seconds
 Image            has    18874 counts for 0.5525     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584     22007            276         0         0     18301
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584     22007            276         0         0     18301
   in   34164.12 seconds
 Image            has    22007 counts for 0.6442     counts/sec
 Command not found; type ? for a command listing
!ad63007000g300270m:ASCA >
!ad63007000g300270m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g300270m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g300270m:ASCA > read events ad63007000g300270m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g300270m:ASCA-GIS3-PH > set image sky
!ad63007000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad63007000g300270m:ASCA-GIS3-PH > extract image
!ad63007000g300270m:ASCA-GIS3-PH > save image outfile=ad63007000g300270m.img
Wrote image to file ad63007000g300270m.img
!ad63007000g300270m:ASCA-GIS3-PH > filter pha_cut 0 42
!ad63007000g300270m:ASCA-GIS3-PH > extract image
!ad63007000g300270m:ASCA-GIS3-PH > save image outfile=ad63007000g300270m_lo.img
Wrote image to file ad63007000g300270m_lo.img
!ad63007000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad63007000g300270m:ASCA-GIS3-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g300270m:ASCA-GIS3-PH > extract image
!ad63007000g300270m:ASCA-GIS3-PH > save image outfile=ad63007000g300270m_hi.img
Wrote image to file ad63007000g300270m_hi.img
!ad63007000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad63007000g300370l.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g300370l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g300370l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6153
 Mean   RA/DEC/ROLL :       10.6909      41.3583     306.6153
 Pnt    RA/DEC/ROLL :       10.7043      41.3621     306.6153
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :             5
 Total GTI (secs)   :       415.726
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       64.0000000      64.0000000
  20 Percent Complete: Total/live time:      128.0000000     128.0000000
  30 Percent Complete: Total/live time:      141.8986664     141.8986664
  40 Percent Complete: Total/live time:      221.8983154     221.8983154
  50 Percent Complete: Total/live time:      221.8983154     221.8983154
  60 Percent Complete: Total/live time:      320.2124329     320.2124329
  70 Percent Complete: Total/live time:      320.2124329     320.2124329
  80 Percent Complete: Total/live time:      415.7261047     415.7261047
 100 Percent Complete: Total/live time:      415.7261047     415.7261047
 
 Number of attitude steps  used:            9
 Number of attitude steps avail:         5319
 Mean RA/DEC pixel offset:        0.5994      -1.8326
 
    writing expo file: ad63007000g300370l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g300370l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g300370l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       516              2         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518       516              2         0         0         0
   in     415.73 seconds
 Image            has      516 counts for  1.241     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       248              2         0         0       268
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518       248              2         0         0       268
   in     415.73 seconds
 Image            has      248 counts for 0.5965     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       274              2         0         0       242
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518       274              2         0         0       242
   in     415.73 seconds
 Image            has      274 counts for 0.6591     counts/sec
 Command not found; type ? for a command listing
!ad63007000g300370l:ASCA >
!ad63007000g300370l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g300370l:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g300370l:ASCA > read events ad63007000g300370l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g300370l:ASCA-GIS3-PH > set image sky
!ad63007000g300370l:ASCA-GIS3-PH > filter region corner_point.reg
!ad63007000g300370l:ASCA-GIS3-PH > extract image
!ad63007000g300370l:ASCA-GIS3-PH > save image outfile=ad63007000g300370l.img
Wrote image to file ad63007000g300370l.img
!ad63007000g300370l:ASCA-GIS3-PH > filter pha_cut 0 42
!ad63007000g300370l:ASCA-GIS3-PH > extract image
!ad63007000g300370l:ASCA-GIS3-PH > save image outfile=ad63007000g300370l_lo.img
Wrote image to file ad63007000g300370l_lo.img
!ad63007000g300370l:ASCA-GIS3-PH > clear pha_cut
!ad63007000g300370l:ASCA-GIS3-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g300370l:ASCA-GIS3-PH > extract image
!ad63007000g300370l:ASCA-GIS3-PH > save image outfile=ad63007000g300370l_hi.img
Wrote image to file ad63007000g300370l_hi.img
!ad63007000g300370l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad63007000g300470h.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g300470h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g300470h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6145
 Mean   RA/DEC/ROLL :       10.6890      41.3590     306.6145
 Pnt    RA/DEC/ROLL :       10.7102      41.3588     306.6145
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :             5
 Total GTI (secs)   :       981.997
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      517.9982910     517.9982910
  20 Percent Complete: Total/live time:      517.9982910     517.9982910
  30 Percent Complete: Total/live time:      981.9968262     981.9968262
 100 Percent Complete: Total/live time:      981.9968262     981.9968262
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         2249
 Mean RA/DEC pixel offset:        1.0117      -1.7854
 
    writing expo file: ad63007000g300470h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g300470h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g300470h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130      1127              3         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130      1127              3         0         0         0
   in     982.00 seconds
 Image            has     1127 counts for  1.148     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       532              3         0         0       595
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130       532              3         0         0       595
   in     982.00 seconds
 Image            has      532 counts for 0.5418     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       610              3         0         0       517
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130       610              3         0         0       517
   in     982.00 seconds
 Image            has      610 counts for 0.6212     counts/sec
 Command not found; type ? for a command listing
!ad63007000g300470h:ASCA >
!ad63007000g300470h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g300470h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g300470h:ASCA > read events ad63007000g300470h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g300470h:ASCA-GIS3-PH > set image sky
!ad63007000g300470h:ASCA-GIS3-PH > filter region corner_point.reg
!ad63007000g300470h:ASCA-GIS3-PH > extract image
!ad63007000g300470h:ASCA-GIS3-PH > save image outfile=ad63007000g300470h.img
Wrote image to file ad63007000g300470h.img
!ad63007000g300470h:ASCA-GIS3-PH > filter pha_cut 0 42
!ad63007000g300470h:ASCA-GIS3-PH > extract image
!ad63007000g300470h:ASCA-GIS3-PH > save image outfile=ad63007000g300470h_lo.img
Wrote image to file ad63007000g300470h_lo.img
!ad63007000g300470h:ASCA-GIS3-PH > clear pha_cut
!ad63007000g300470h:ASCA-GIS3-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g300470h:ASCA-GIS3-PH > extract image
!ad63007000g300470h:ASCA-GIS3-PH > save image outfile=ad63007000g300470h_hi.img
Wrote image to file ad63007000g300470h_hi.img
!ad63007000g300470h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad63007000g300670m.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad63007000g300670m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000g300670m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6153
 Mean   RA/DEC/ROLL :       10.6927      41.3577     306.6153
 Pnt    RA/DEC/ROLL :       10.7060      41.3596     306.6153
 
 Image rebin factor :             1
 Attitude Records   :        148379
 GTI intervals      :            15
 Total GTI (secs)   :       431.999
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       48.0000000      48.0000000
  20 Percent Complete: Total/live time:       93.9997635      93.9997635
  30 Percent Complete: Total/live time:      143.9998474     143.9998474
  40 Percent Complete: Total/live time:      189.9997711     189.9997711
  50 Percent Complete: Total/live time:      221.9996033     221.9996033
  60 Percent Complete: Total/live time:      271.9996338     271.9996338
  70 Percent Complete: Total/live time:      335.9995117     335.9995117
  80 Percent Complete: Total/live time:      367.9994507     367.9994507
  90 Percent Complete: Total/live time:      399.9993896     399.9993896
 100 Percent Complete: Total/live time:      431.9993286     431.9993286
 
 Number of attitude steps  used:           23
 Number of attitude steps avail:         5960
 Mean RA/DEC pixel offset:        0.1200      -1.8772
 
    writing expo file: ad63007000g300670m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000g300670m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       511              5         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516       511              5         0         0         0
   in     432.00 seconds
 Image            has      511 counts for  1.183     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       241              5         0         0       270
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516       241              5         0         0       270
   in     432.00 seconds
 Image            has      241 counts for 0.5579     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       281              5         0         0       230
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516       281              5         0         0       230
   in     432.00 seconds
 Image            has      281 counts for 0.6505     counts/sec
 Command not found; type ? for a command listing
!ad63007000g300670m:ASCA >
!ad63007000g300670m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000g300670m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000g300670m:ASCA > read events ad63007000g300670m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!ad63007000g300670m:ASCA-GIS3-PH > set image sky
!ad63007000g300670m:ASCA-GIS3-PH > filter region corner_point.reg
!ad63007000g300670m:ASCA-GIS3-PH > extract image
!ad63007000g300670m:ASCA-GIS3-PH > save image outfile=ad63007000g300670m.img
Wrote image to file ad63007000g300670m.img
!ad63007000g300670m:ASCA-GIS3-PH > filter pha_cut 0 42
!ad63007000g300670m:ASCA-GIS3-PH > extract image
!ad63007000g300670m:ASCA-GIS3-PH > save image outfile=ad63007000g300670m_lo.img
Wrote image to file ad63007000g300670m_lo.img
!ad63007000g300670m:ASCA-GIS3-PH > clear pha_cut
!ad63007000g300670m:ASCA-GIS3-PH > filter pha_cut 42 256
Warning: your PI upper bound:   256 is above the maximum value.
!ad63007000g300670m:ASCA-GIS3-PH > extract image
!ad63007000g300670m:ASCA-GIS3-PH > save image outfile=ad63007000g300670m_hi.img
Wrote image to file ad63007000g300670m_hi.img
!ad63007000g300670m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad63007000s000102h.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6102
 Mean   RA/DEC/ROLL :       10.6850      41.3374     306.6102
 Pnt    RA/DEC/ROLL :       10.7151      41.3764     306.6102
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           311
 GTI intervals      :           156
 Total GTI (secs)   :     47221.938
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     5473.4194336    5473.4194336
  20 Percent Complete: Total/live time:     9981.0878906    9981.0878906
  30 Percent Complete: Total/live time:    15315.4550781   15315.4550781
  40 Percent Complete: Total/live time:    19409.0820312   19409.0820312
  50 Percent Complete: Total/live time:    24713.1894531   24713.1894531
  60 Percent Complete: Total/live time:    29039.0996094   29039.0996094
  70 Percent Complete: Total/live time:    33753.4921875   33753.4921875
  80 Percent Complete: Total/live time:    39069.3359375   39069.3359375
  90 Percent Complete: Total/live time:    43084.0156250   43084.0156250
 100 Percent Complete: Total/live time:    47221.9375000   47221.9375000
 
 Number of attitude steps  used:          108
 Number of attitude steps avail:       120324
 Mean RA/DEC pixel offset:      -56.2178     -94.2419
 
    writing expo file: ad63007000s000102h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000102h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     45025              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025     45025              0         0         0         0
   in   47221.93 seconds
 Image            has    45025 counts for 0.9535     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     26494              0         0         0     18531
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025     26494              0         0         0     18531
   in   47221.93 seconds
 Image            has    26494 counts for 0.5611     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     18575              0         0         0     26450
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025     18575              0         0         0     26450
   in   47221.93 seconds
 Image            has    18575 counts for 0.3934     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000102h:ASCA >
!ad63007000s000102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000102h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000102h:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000102h.img
Wrote image to file ad63007000s000102h.img
!ad63007000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000102h_lo.img
Wrote image to file ad63007000s000102h_lo.img
!ad63007000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000102h_hi.img
Wrote image to file ad63007000s000102h_hi.img
!ad63007000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s000202m.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000202m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000202m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6101
 Mean   RA/DEC/ROLL :       10.6854      41.3376     306.6101
 Pnt    RA/DEC/ROLL :       10.7137      41.3794     306.6101
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           286
 GTI intervals      :            55
 Total GTI (secs)   :     28575.852
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     3323.7385254    3323.7385254
  20 Percent Complete: Total/live time:     6249.2031250    6249.2031250
  30 Percent Complete: Total/live time:     9023.0058594    9023.0058594
  40 Percent Complete: Total/live time:    12138.8632812   12138.8632812
  50 Percent Complete: Total/live time:    14686.6064453   14686.6064453
  60 Percent Complete: Total/live time:    17964.4238281   17964.4238281
  70 Percent Complete: Total/live time:    20701.9062500   20701.9062500
  80 Percent Complete: Total/live time:    24052.5429688   24052.5429688
  90 Percent Complete: Total/live time:    26008.8535156   26008.8535156
 100 Percent Complete: Total/live time:    28575.8535156   28575.8535156
 
 Number of attitude steps  used:           75
 Number of attitude steps avail:        31835
 Mean RA/DEC pixel offset:      -56.1053     -91.9842
 
    writing expo file: ad63007000s000202m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000202m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260     26260              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260     26260              0         0         0         0
   in   28575.86 seconds
 Image            has    26260 counts for 0.9190     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260     15444              0         0         0     10816
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260     15444              0         0         0     10816
   in   28575.86 seconds
 Image            has    15444 counts for 0.5405     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260     10848              0         0         0     15412
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260     10848              0         0         0     15412
   in   28575.86 seconds
 Image            has    10848 counts for 0.3796     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000202m:ASCA >
!ad63007000s000202m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000202m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000202m:ASCA > read events ad63007000s000202m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000202m.img
Wrote image to file ad63007000s000202m.img
!ad63007000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000202m_lo.img
Wrote image to file ad63007000s000202m_lo.img
!ad63007000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000202m_hi.img
Wrote image to file ad63007000s000202m_hi.img
!ad63007000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s000302h.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000302h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000302h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL          ON
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6107
 Mean   RA/DEC/ROLL :       10.6852      41.3374     306.6107
 Pnt    RA/DEC/ROLL :       10.7160      41.3765     306.6107
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           277
 GTI intervals      :            16
 Total GTI (secs)   :      1007.300
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      114.0987015     114.0987015
  20 Percent Complete: Total/live time:      276.4370117     276.4370117
  30 Percent Complete: Total/live time:      380.6765137     380.6765137
  40 Percent Complete: Total/live time:      452.9342957     452.9342957
  50 Percent Complete: Total/live time:      525.2288818     525.2288818
  60 Percent Complete: Total/live time:      653.8739014     653.8739014
  70 Percent Complete: Total/live time:      723.8112183     723.8112183
  80 Percent Complete: Total/live time:      890.7127686     890.7127686
  90 Percent Complete: Total/live time:     1007.3001099    1007.3001099
 100 Percent Complete: Total/live time:     1007.3001099    1007.3001099
 
 Number of attitude steps  used:           24
 Number of attitude steps avail:        10269
 Mean RA/DEC pixel offset:      -51.0819     -92.4449
 
    writing expo file: ad63007000s000302h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000302h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000302h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       890              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890       890              0         0         0         0
   in    1007.30 seconds
 Image            has      890 counts for 0.8835     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       596              0         0         0       294
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890       596              0         0         0       294
   in    1007.30 seconds
 Image            has      596 counts for 0.5917     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       294              0         0         0       596
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890       294              0         0         0       596
   in    1007.30 seconds
 Image            has      294 counts for 0.2919     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000302h:ASCA >
!ad63007000s000302h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000302h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000302h:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000302h:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000302h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000302h.img
Wrote image to file ad63007000s000302h.img
!ad63007000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000302h_lo.img
Wrote image to file ad63007000s000302h_lo.img
!ad63007000s000302h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000302h_hi.img
Wrote image to file ad63007000s000302h_hi.img
!ad63007000s000302h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s000402h.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000402h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000402h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6173
 Mean   RA/DEC/ROLL :       10.6882      41.3349     306.6173
 Pnt    RA/DEC/ROLL :       10.7097      41.3823     306.6173
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           237
 GTI intervals      :            20
 Total GTI (secs)   :      2301.769
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     1160.8084717    1160.8084717
  20 Percent Complete: Total/live time:     1160.8084717    1160.8084717
  30 Percent Complete: Total/live time:     1165.8083496    1165.8083496
  40 Percent Complete: Total/live time:     1165.8083496    1165.8083496
  50 Percent Complete: Total/live time:     2301.7687988    2301.7687988
 100 Percent Complete: Total/live time:     2301.7687988    2301.7687988
 
 Number of attitude steps  used:            4
 Number of attitude steps avail:         6092
 Mean RA/DEC pixel offset:      -52.2797     -70.7825
 
    writing expo file: ad63007000s000402h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000402h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114      2114              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114      2114              0         0         0         0
   in    2301.77 seconds
 Image            has     2114 counts for 0.9184     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114      1266              0         0         0       848
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114      1266              0         0         0       848
   in    2301.77 seconds
 Image            has     1266 counts for 0.5500     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       851              0         0         0      1263
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       851              0         0         0      1263
   in    2301.77 seconds
 Image            has      851 counts for 0.3697     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000402h:ASCA >
!ad63007000s000402h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000402h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000402h:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000402h:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000402h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000402h.img
Wrote image to file ad63007000s000402h.img
!ad63007000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000402h_lo.img
Wrote image to file ad63007000s000402h_lo.img
!ad63007000s000402h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000402h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000402h:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000402h:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000402h_hi.img
Wrote image to file ad63007000s000402h_hi.img
!ad63007000s000402h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s000502l.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000502l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000502l.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6102
 Mean   RA/DEC/ROLL :       10.6847      41.3383     306.6102
 Pnt    RA/DEC/ROLL :       10.7133      41.3815     306.6102
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :            46
 GTI intervals      :             3
 Total GTI (secs)   :        38.894
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       12.9902182      12.9902182
  20 Percent Complete: Total/live time:       25.9610882      25.9610882
  30 Percent Complete: Total/live time:       25.9610882      25.9610882
  40 Percent Complete: Total/live time:       38.8937836      38.8937836
 100 Percent Complete: Total/live time:       38.8937836      38.8937836
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:           19
 Mean RA/DEC pixel offset:      -28.8167     -62.9772
 
    writing expo file: ad63007000s000502l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000502l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000502l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88        88              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88        88              0         0         0         0
   in      38.89 seconds
 Image            has       88 counts for  2.263     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88        81              0         0         0         7
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88        81              0         0         0         7
   in      38.89 seconds
 Image            has       81 counts for  2.083     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         7              0         0         0        81
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88         7              0         0         0        81
   in      38.89 seconds
 Image            has        7 counts for 0.1800     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000502l:ASCA >
!ad63007000s000502l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000502l:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000502l:ASCA > read events ad63007000s000502l.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000502l:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000502l:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000502l:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000502l:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000502l.img
Wrote image to file ad63007000s000502l.img
!ad63007000s000502l:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000502l:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000502l:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000502l_lo.img
Wrote image to file ad63007000s000502l_lo.img
!ad63007000s000502l:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000502l:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000502l:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000502l:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000502l_hi.img
Wrote image to file ad63007000s000502l_hi.img
!ad63007000s000502l:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s000602m.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s000602m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s000602m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL          ON
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6101
 Mean   RA/DEC/ROLL :       10.6843      41.3380     306.6101
 Pnt    RA/DEC/ROLL :       10.7149      41.3770     306.6101
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           188
 GTI intervals      :            19
 Total GTI (secs)   :      1450.364
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      160.0550995     160.0550995
  20 Percent Complete: Total/live time:      316.2228394     316.2228394
  30 Percent Complete: Total/live time:      468.5192566     468.5192566
  40 Percent Complete: Total/live time:      644.9984741     644.9984741
  50 Percent Complete: Total/live time:      773.4041138     773.4041138
  60 Percent Complete: Total/live time:      902.3424683     902.3424683
  70 Percent Complete: Total/live time:     1032.8387451    1032.8387451
  80 Percent Complete: Total/live time:     1224.4730225    1224.4730225
  90 Percent Complete: Total/live time:     1321.0788574    1321.0788574
 100 Percent Complete: Total/live time:     1450.3641357    1450.3641357
 
 Number of attitude steps  used:           32
 Number of attitude steps avail:         8725
 Mean RA/DEC pixel offset:     -123.1525     -95.6083
 
    writing expo file: ad63007000s000602m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s000602m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       420              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420       420              0         0         0         0
   in    1450.36 seconds
 Image            has      420 counts for 0.2896     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       259              0         0         0       161
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420       259              0         0         0       161
   in    1450.36 seconds
 Image            has      259 counts for 0.1786     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       161              0         0         0       259
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420       161              0         0         0       259
   in    1450.36 seconds
 Image            has      161 counts for 0.1110     counts/sec
 Command not found; type ? for a command listing
!ad63007000s000602m:ASCA >
!ad63007000s000602m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s000602m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s000602m:ASCA > read events ad63007000s000602m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s000602m:ASCA-SIS0-BRIGHT > set image sky
!ad63007000s000602m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad63007000s000602m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000602m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000602m.img
Wrote image to file ad63007000s000602m.img
!ad63007000s000602m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad63007000s000602m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000602m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000602m_lo.img
Wrote image to file ad63007000s000602m_lo.img
!ad63007000s000602m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad63007000s000602m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s000602m:ASCA-SIS0-BRIGHT > extract image
!ad63007000s000602m:ASCA-SIS0-BRIGHT > save image outfile=ad63007000s000602m_hi.img
Wrote image to file ad63007000s000602m_hi.img
!ad63007000s000602m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s100102h.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s100102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s100102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6219
 Mean   RA/DEC/ROLL :       10.7030      41.3459     306.6219
 Pnt    RA/DEC/ROLL :       10.6973      41.3677     306.6219
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           295
 GTI intervals      :           208
 Total GTI (secs)   :     50800.398
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     5883.1455078    5883.1455078
  20 Percent Complete: Total/live time:    10760.2460938   10760.2460938
  30 Percent Complete: Total/live time:    16600.7675781   16600.7675781
  40 Percent Complete: Total/live time:    21687.7460938   21687.7460938
  50 Percent Complete: Total/live time:    26926.7460938   26926.7460938
  60 Percent Complete: Total/live time:    31145.4433594   31145.4433594
  70 Percent Complete: Total/live time:    36098.4843750   36098.4843750
  80 Percent Complete: Total/live time:    42410.3867188   42410.3867188
  90 Percent Complete: Total/live time:    46257.7343750   46257.7343750
 100 Percent Complete: Total/live time:    50800.3906250   50800.3906250
 
 Number of attitude steps  used:          107
 Number of attitude steps avail:       128400
 Mean RA/DEC pixel offset:      -60.1302     -22.9773
 
    writing expo file: ad63007000s100102h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s100102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s100102h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597     35597              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597     35597              0         0         0         0
   in   50800.39 seconds
 Image            has    35597 counts for 0.7007     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597     19439              0         0         0     16158
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597     19439              0         0         0     16158
   in   50800.39 seconds
 Image            has    19439 counts for 0.3827     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597     16189              0         0         0     19408
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597     16189              0         0         0     19408
   in   50800.39 seconds
 Image            has    16189 counts for 0.3187     counts/sec
 Command not found; type ? for a command listing
!ad63007000s100102h:ASCA >
!ad63007000s100102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s100102h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s100102h:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad63007000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad63007000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100102h.img
Wrote image to file ad63007000s100102h.img
!ad63007000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad63007000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100102h_lo.img
Wrote image to file ad63007000s100102h_lo.img
!ad63007000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad63007000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100102h_hi.img
Wrote image to file ad63007000s100102h_hi.img
!ad63007000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s100202m.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s100202m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s100202m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6218
 Mean   RA/DEC/ROLL :       10.7031      41.3463     306.6218
 Pnt    RA/DEC/ROLL :       10.6971      41.3683     306.6218
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           284
 GTI intervals      :            63
 Total GTI (secs)   :     30751.990
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     3406.0065918    3406.0065918
  20 Percent Complete: Total/live time:     6620.1811523    6620.1811523
  30 Percent Complete: Total/live time:     9598.0781250    9598.0781250
  40 Percent Complete: Total/live time:    12796.3886719   12796.3886719
  50 Percent Complete: Total/live time:    15922.6572266   15922.6572266
  60 Percent Complete: Total/live time:    19067.6093750   19067.6093750
  70 Percent Complete: Total/live time:    21943.8203125   21943.8203125
  80 Percent Complete: Total/live time:    25585.2558594   25585.2558594
  90 Percent Complete: Total/live time:    28056.9902344   28056.9902344
 100 Percent Complete: Total/live time:    30751.9902344   30751.9902344
 
 Number of attitude steps  used:           87
 Number of attitude steps avail:        34317
 Mean RA/DEC pixel offset:      -60.5335     -21.1261
 
    writing expo file: ad63007000s100202m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s100202m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s100202m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455     20455              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455     20455              0         0         0         0
   in   30751.99 seconds
 Image            has    20455 counts for 0.6652     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455     11131              0         0         0      9324
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455     11131              0         0         0      9324
   in   30751.99 seconds
 Image            has    11131 counts for 0.3620     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      9348              0         0         0     11107
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455      9348              0         0         0     11107
   in   30751.99 seconds
 Image            has     9348 counts for 0.3040     counts/sec
 Command not found; type ? for a command listing
!ad63007000s100202m:ASCA >
!ad63007000s100202m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s100202m:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s100202m:ASCA > read events ad63007000s100202m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad63007000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad63007000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100202m.img
Wrote image to file ad63007000s100202m.img
!ad63007000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad63007000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100202m_lo.img
Wrote image to file ad63007000s100202m_lo.img
!ad63007000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad63007000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100202m_hi.img
Wrote image to file ad63007000s100202m_hi.img
!ad63007000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s100302l.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s100302l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s100302l.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:           ON          ON          ON          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6218
 Mean   RA/DEC/ROLL :       10.7019      41.3471     306.6218
 Pnt    RA/DEC/ROLL :       10.6946      41.3731     306.6218
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :            34
 GTI intervals      :             3
 Total GTI (secs)   :        38.894
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       12.9902182      12.9902182
  20 Percent Complete: Total/live time:       25.9610882      25.9610882
  30 Percent Complete: Total/live time:       25.9610882      25.9610882
  40 Percent Complete: Total/live time:       38.8937836      38.8937836
 100 Percent Complete: Total/live time:       38.8937836      38.8937836
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:           19
 Mean RA/DEC pixel offset:      -31.7796     -15.0765
 
    writing expo file: ad63007000s100302l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s100302l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s100302l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101       101              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101       101              0         0         0         0
   in      38.89 seconds
 Image            has      101 counts for  2.597     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101        82              0         0         0        19
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101        82              0         0         0        19
   in      38.89 seconds
 Image            has       82 counts for  2.108     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101        19              0         0         0        82
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101        19              0         0         0        82
   in      38.89 seconds
 Image            has       19 counts for 0.4885     counts/sec
 Command not found; type ? for a command listing
!ad63007000s100302l:ASCA >
!ad63007000s100302l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s100302l:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s100302l:ASCA > read events ad63007000s100302l.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s100302l:ASCA-SIS1-BRIGHT > set image sky
!ad63007000s100302l:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad63007000s100302l:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100302l:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100302l.img
Wrote image to file ad63007000s100302l.img
!ad63007000s100302l:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad63007000s100302l:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100302l:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100302l_lo.img
Wrote image to file ad63007000s100302l_lo.img
!ad63007000s100302l:ASCA-SIS1-BRIGHT > clear pha_cut
!ad63007000s100302l:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s100302l:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100302l:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100302l_hi.img
Wrote image to file ad63007000s100302l_hi.img
!ad63007000s100302l:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad63007000s100402h.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad63007000s100402h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad63007000s100402h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON          ON         OFF
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa950729_2235.0800
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       10.6975      41.3601     306.6205
 Mean   RA/DEC/ROLL :       10.7035      41.3459     306.6205
 Pnt    RA/DEC/ROLL :       10.6953      41.3718     306.6205
 
 Image rebin factor :             4
 Attitude Records   :        148379
 Hot Pixels         :           189
 GTI intervals      :             7
 Total GTI (secs)   :      1001.720
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     1001.7203369    1001.7203369
 100 Percent Complete: Total/live time:     1001.7203369    1001.7203369
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:         2222
 Mean RA/DEC pixel offset:      -30.2864     -12.2691
 
    writing expo file: ad63007000s100402h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad63007000s100402h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702       702              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702       702              0         0         0         0
   in    1001.72 seconds
 Image            has      702 counts for 0.7008     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702       406              0         0         0       296
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702       406              0         0         0       296
   in    1001.72 seconds
 Image            has      406 counts for 0.4053     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702       297              0         0         0       405
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702       297              0         0         0       405
   in    1001.72 seconds
 Image            has      297 counts for 0.2965     counts/sec
 Command not found; type ? for a command listing
!ad63007000s100402h:ASCA >
!ad63007000s100402h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad63007000s100402h:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!ad63007000s100402h:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!ad63007000s100402h:ASCA-SIS1-BRIGHT > set image sky
!ad63007000s100402h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad63007000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100402h.img
Wrote image to file ad63007000s100402h.img
!ad63007000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad63007000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100402h_lo.img
Wrote image to file ad63007000s100402h_lo.img
!ad63007000s100402h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad63007000s100402h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad63007000s100402h:ASCA-SIS1-BRIGHT > extract image
!ad63007000s100402h:ASCA-SIS1-BRIGHT > save image outfile=ad63007000s100402h_hi.img
Wrote image to file ad63007000s100402h_hi.img
!ad63007000s100402h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis images
-> Summing the following images to produce ad63007000sis32002.totexpo
ad63007000s000102h.expo
ad63007000s000202m.expo
ad63007000s000302h.expo
ad63007000s000402h.expo
ad63007000s000502l.expo
ad63007000s000602m.expo
ad63007000s100102h.expo
ad63007000s100202m.expo
ad63007000s100302l.expo
ad63007000s100402h.expo
-> Summing the following images to produce ad63007000sis32002_all.totsky
ad63007000s000102h.img
ad63007000s000202m.img
ad63007000s000302h.img
ad63007000s000402h.img
ad63007000s000502l.img
ad63007000s000602m.img
ad63007000s100102h.img
ad63007000s100202m.img
ad63007000s100302l.img
ad63007000s100402h.img
-> Summing the following images to produce ad63007000sis32002_lo.totsky
ad63007000s000102h_lo.img
ad63007000s000202m_lo.img
ad63007000s000302h_lo.img
ad63007000s000402h_lo.img
ad63007000s000502l_lo.img
ad63007000s000602m_lo.img
ad63007000s100102h_lo.img
ad63007000s100202m_lo.img
ad63007000s100302l_lo.img
ad63007000s100402h_lo.img
-> Summing the following images to produce ad63007000sis32002_hi.totsky
ad63007000s000102h_hi.img
ad63007000s000202m_hi.img
ad63007000s000302h_hi.img
ad63007000s000402h_hi.img
ad63007000s000502l_hi.img
ad63007000s000602m_hi.img
ad63007000s100102h_hi.img
ad63007000s100202m_hi.img
ad63007000s100302l_hi.img
ad63007000s100402h_hi.img
-> Running XIMAGE to create ad63007000sis32002.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   20
![1]XIMAGE> read/fits ad63007000sis32002_all.totsky
 Reading an image
 Telescope ASCA SIS0
  Image display size =  320
 Done, closing file
  Largest, Smallest    76.0000  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  76 min:  0
![2]XIMAGE> read/exp_map ad63007000sis32002.totexpo
 Reading an image
 Telescope ASCA SIS0
  Image display size =  320
 Done, closing file
  Largest, Smallest    2719.82  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  2719 min:  0
![3]XIMAGE> smooth
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 Displaying image
 The image is exposure corrected
  Min =  0 max =   55
![7]XIMAGE> grid
![8]XIMAGE> scale
 scal_f, min_inten    1.00000  0.
 i,inten,mm,pp  1  0.  0  0
 i,inten,mm,pp  2    4.00000  40  -1
 i,inten,mm,pp  3    8.00000  80  -1
 i,inten,mm,pp  4    14.0000  14  0
![9]XIMAGE> exit
-> Summing gis images
-> Summing the following images to produce ad63007000gis25670.totexpo
ad63007000g200170h.expo
ad63007000g200270m.expo
ad63007000g200370l.expo
ad63007000g200470h.expo
ad63007000g200670m.expo
ad63007000g300170h.expo
ad63007000g300270m.expo
ad63007000g300370l.expo
ad63007000g300470h.expo
ad63007000g300670m.expo
-> Summing the following images to produce ad63007000gis25670_all.totsky
ad63007000g200170h.img
ad63007000g200270m.img
ad63007000g200370l.img
ad63007000g200470h.img
ad63007000g200670m.img
ad63007000g300170h.img
ad63007000g300270m.img
ad63007000g300370l.img
ad63007000g300470h.img
ad63007000g300670m.img
-> Summing the following images to produce ad63007000gis25670_lo.totsky
ad63007000g200170h_lo.img
ad63007000g200270m_lo.img
ad63007000g200370l_lo.img
ad63007000g200470h_lo.img
ad63007000g200670m_lo.img
ad63007000g300170h_lo.img
ad63007000g300270m_lo.img
ad63007000g300370l_lo.img
ad63007000g300470h_lo.img
ad63007000g300670m_lo.img
-> Summing the following images to produce ad63007000gis25670_hi.totsky
ad63007000g200170h_hi.img
ad63007000g200270m_hi.img
ad63007000g200370l_hi.img
ad63007000g200470h_hi.img
ad63007000g200670m_hi.img
ad63007000g300170h_hi.img
ad63007000g300270m_hi.img
ad63007000g300370l_hi.img
ad63007000g300470h_hi.img
ad63007000g300670m_hi.img
-> Running XIMAGE to create ad63007000gis25670.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   20
![1]XIMAGE> read/fits ad63007000gis25670_all.totsky
 Reading an image
 Telescope ASCA GIS2
  Image display size =  256
 Done, closing file
  Largest, Smallest    232.000  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  232 min:  0
![2]XIMAGE> read/exp_map ad63007000gis25670.totexpo
 Reading an image
 Telescope ASCA GIS2
  Image display size =  256
 Done, closing file
  Largest, Smallest    2951.88  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  2951 min:  0
![3]XIMAGE> smooth
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 Displaying image
 The image is exposure corrected
  Min =  0 max =   32767
![7]XIMAGE> grid
![8]XIMAGE> scale
 scal_f, min_inten    1.00000  0.
 i,inten,mm,pp  1  0.  0  0
 i,inten,mm,pp  2    4.00000  40  -1
 i,inten,mm,pp  3    9.00000  90  -1
 i,inten,mm,pp  4    26.0000  26  0
![9]XIMAGE> exit

Detecting sources in summed images ( 09:14:44 )

-> Smoothing ad63007000gis25670_all.totsky with ad63007000gis25670.totexpo
-> Clipping exposures below 26566.93872975 seconds
-> Detecting sources in ad63007000gis25670_all.smooth
-> Standard Output From STOOL ascasource:
135 107 0.00102007 15 12 64.1064
161 116 0.000761598 12 9 49.6344
126 167 0.000370134 10 9 19.7489
153 47 0.000274856 7 7 18.0095
-> Smoothing ad63007000gis25670_hi.totsky with ad63007000gis25670.totexpo
-> Clipping exposures below 26566.93872975 seconds
-> Detecting sources in ad63007000gis25670_hi.smooth
-> Standard Output From STOOL ascasource:
135 107 0.000585314 14 10 57.0169
160 116 0.000450435 12 8 47.5312
126 167 0.000241528 15 9 21.2822
153 47 0.000226916 9 6 22.9898
-> Smoothing ad63007000gis25670_lo.totsky with ad63007000gis25670.totexpo
-> Clipping exposures below 26566.93872975 seconds
-> Detecting sources in ad63007000gis25670_lo.smooth
-> Standard Output From STOOL ascasource:
134 107 0.000462982 13 14 86.4417
161 116 0.000323711 13 10 52.492
126 167 0.000133625 12 11 16.2304
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
135 107 15 T
161 116 12 F
126 167 10 F
153 47 7 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad63007000gis25670.src
-> Smoothing ad63007000sis32002_all.totsky with ad63007000sis32002.totexpo
-> Clipping exposures below 24478.36788495 seconds
-> Detecting sources in ad63007000sis32002_all.smooth
-> Standard Output From STOOL ascasource:
234 131 0.000363375 30 9 110.517
174 108 0.000352816 29 17 149.874
151 251 0.000170233 25 9 51.0987
149 134 0.000115791 7 8 50.0932
-> Smoothing ad63007000sis32002_hi.totsky with ad63007000sis32002.totexpo
-> Clipping exposures below 24478.36788495 seconds
-> Detecting sources in ad63007000sis32002_hi.smooth
-> Standard Output From STOOL ascasource:
234 131 0.000161805 33 10 88.3137
174 108 0.000158253 30 15 116.153
151 251 9.19258e-05 82 9 53.3397
-> Smoothing ad63007000sis32002_lo.totsky with ad63007000sis32002.totexpo
-> Clipping exposures below 24478.36788495 seconds
-> Detecting sources in ad63007000sis32002_lo.smooth
-> Standard Output From STOOL ascasource:
234 131 0.000202256 24 8 117.516
173 108 0.000197988 39 20 207.086
150 251 8.57964e-05 24 9 45.0175
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
234 131 30 F
174 108 29 T
151 251 25 F
149 134 7 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad63007000sis32002.src
-> Generating region files
-> Converting (936.0,524.0,2.0) to s0 detector coordinates
-> Using events in: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   22195.000
 The mean of the selected column is                  693.59375
 The standard deviation of the selected column is    6.2209810
 The minimum of selected column is                   682.00000
 The maximum of selected column is                   703.00000
 The number of points used in calculation is               32
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9198.0000
 The mean of the selected column is                  287.43750
 The standard deviation of the selected column is    2.7112371
 The minimum of selected column is                   281.00000
 The maximum of selected column is                   293.00000
 The number of points used in calculation is               32
-> Converting (696.0,432.0,2.0) to s0 detector coordinates
-> Using events in: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   19636.000
 The mean of the selected column is                  478.92683
 The standard deviation of the selected column is    5.7331939
 The minimum of selected column is                   466.00000
 The maximum of selected column is                   487.00000
 The number of points used in calculation is               41
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   17430.000
 The mean of the selected column is                  425.12195
 The standard deviation of the selected column is    2.6191136
 The minimum of selected column is                   421.00000
 The maximum of selected column is                   432.00000
 The number of points used in calculation is               41
-> Converting (604.0,1004.0,2.0) to s0 detector coordinates
-> Using events in: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9700.0000
 The mean of the selected column is                  881.81818
 The standard deviation of the selected column is    6.3689588
 The minimum of selected column is                   873.00000
 The maximum of selected column is                   892.00000
 The number of points used in calculation is               11
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9237.0000
 The mean of the selected column is                  839.72727
 The standard deviation of the selected column is    2.9014103
 The minimum of selected column is                   835.00000
 The maximum of selected column is                   844.00000
 The number of points used in calculation is               11
-> Converting (596.0,536.0,2.0) to s0 detector coordinates
-> Using events in: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   4546.0000
 The mean of the selected column is                  505.11111
 The standard deviation of the selected column is    3.8224483
 The minimum of selected column is                   498.00000
 The maximum of selected column is                   510.00000
 The number of points used in calculation is                9
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   5106.0000
 The mean of the selected column is                  567.33333
 The standard deviation of the selected column is    2.6457513
 The minimum of selected column is                   564.00000
 The maximum of selected column is                   572.00000
 The number of points used in calculation is                9
-> Converting (936.0,524.0,2.0) to s1 detector coordinates
-> Using events in: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   15880.000
 The mean of the selected column is                  690.43478
 The standard deviation of the selected column is    5.2900085
 The minimum of selected column is                   683.00000
 The maximum of selected column is                   700.00000
 The number of points used in calculation is               23
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   7464.0000
 The mean of the selected column is                  324.52174
 The standard deviation of the selected column is    3.2315148
 The minimum of selected column is                   318.00000
 The maximum of selected column is                   330.00000
 The number of points used in calculation is               23
-> Converting (696.0,432.0,2.0) to s1 detector coordinates
-> Using events in: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9470.0000
 The mean of the selected column is                  473.50000
 The standard deviation of the selected column is    4.1103208
 The minimum of selected column is                   467.00000
 The maximum of selected column is                   482.00000
 The number of points used in calculation is               20
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9234.0000
 The mean of the selected column is                  461.70000
 The standard deviation of the selected column is    2.6377822
 The minimum of selected column is                   457.00000
 The maximum of selected column is                   467.00000
 The number of points used in calculation is               20
-> Converting (604.0,1004.0,2.0) to s1 detector coordinates
-> Using events in: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   14072.000
 The mean of the selected column is                  879.50000
 The standard deviation of the selected column is    6.0553007
 The minimum of selected column is                   870.00000
 The maximum of selected column is                   889.00000
 The number of points used in calculation is               16
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   14025.000
 The mean of the selected column is                  876.56250
 The standard deviation of the selected column is    2.3655514
 The minimum of selected column is                   873.00000
 The maximum of selected column is                   880.00000
 The number of points used in calculation is               16
-> Converting (596.0,536.0,2.0) to s1 detector coordinates
-> Using events in: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2496.0000
 The mean of the selected column is                  499.20000
 The standard deviation of the selected column is    6.9785385
 The minimum of selected column is                   488.00000
 The maximum of selected column is                   505.00000
 The number of points used in calculation is                5
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   3005.0000
 The mean of the selected column is                  601.00000
 The standard deviation of the selected column is    1.5811388
 The minimum of selected column is                   599.00000
 The maximum of selected column is                   603.00000
 The number of points used in calculation is                5
-> Converting (135.0,107.0,2.0) to g2 detector coordinates
-> Using events in: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   123900.00
 The mean of the selected column is                  108.87522
 The standard deviation of the selected column is    1.2142083
 The minimum of selected column is                   106.00000
 The maximum of selected column is                   112.00000
 The number of points used in calculation is             1138
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   124443.00
 The mean of the selected column is                  109.35237
 The standard deviation of the selected column is    1.1071442
 The minimum of selected column is                   107.00000
 The maximum of selected column is                   112.00000
 The number of points used in calculation is             1138
-> Converting (161.0,116.0,2.0) to g2 detector coordinates
-> Using events in: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   141225.00
 The mean of the selected column is                  131.61696
 The standard deviation of the selected column is    1.2299023
 The minimum of selected column is                   129.00000
 The maximum of selected column is                   135.00000
 The number of points used in calculation is             1073
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   100753.00
 The mean of the selected column is                  93.898416
 The standard deviation of the selected column is    1.0960952
 The minimum of selected column is                   92.000000
 The maximum of selected column is                   96.000000
 The number of points used in calculation is             1073
-> Converting (126.0,167.0,2.0) to g2 detector coordinates
-> Using events in: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   71828.000
 The mean of the selected column is                  151.85624
 The standard deviation of the selected column is    1.2573716
 The minimum of selected column is                   149.00000
 The maximum of selected column is                   155.00000
 The number of points used in calculation is              473
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   72168.000
 The mean of the selected column is                  152.57505
 The standard deviation of the selected column is    1.0731563
 The minimum of selected column is                   150.00000
 The maximum of selected column is                   155.00000
 The number of points used in calculation is              473
-> Converting (153.0,47.0,2.0) to g2 detector coordinates
-> Using events in: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> No photons in 2.0 pixel radius
-> Converting (153.0,47.0,7.0) to g2 detector coordinates
-> Using events in: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   13503.000
 The mean of the selected column is                  73.786885
 The standard deviation of the selected column is    2.4502618
 The minimum of selected column is                   69.000000
 The maximum of selected column is                   79.000000
 The number of points used in calculation is              183
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   11416.000
 The mean of the selected column is                  62.382514
 The standard deviation of the selected column is    1.9768218
 The minimum of selected column is                   58.000000
 The maximum of selected column is                   66.000000
 The number of points used in calculation is              183
-> Converting (135.0,107.0,2.0) to g3 detector coordinates
-> Using events in: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   157605.00
 The mean of the selected column is                  114.87245
 The standard deviation of the selected column is    1.2675259
 The minimum of selected column is                   112.00000
 The maximum of selected column is                   118.00000
 The number of points used in calculation is             1372
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   150979.00
 The mean of the selected column is                  110.04300
 The standard deviation of the selected column is    1.1058042
 The minimum of selected column is                   108.00000
 The maximum of selected column is                   112.00000
 The number of points used in calculation is             1372
-> Converting (161.0,116.0,2.0) to g3 detector coordinates
-> Using events in: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   113667.00
 The mean of the selected column is                  137.44498
 The standard deviation of the selected column is    1.2204109
 The minimum of selected column is                   134.00000
 The maximum of selected column is                   140.00000
 The number of points used in calculation is              827
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   78228.000
 The mean of the selected column is                  94.592503
 The standard deviation of the selected column is    1.0979143
 The minimum of selected column is                   92.000000
 The maximum of selected column is                   97.000000
 The number of points used in calculation is              827
-> Converting (126.0,167.0,2.0) to g3 detector coordinates
-> Using events in: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   68982.000
 The mean of the selected column is                  157.49315
 The standard deviation of the selected column is    1.1213340
 The minimum of selected column is                   155.00000
 The maximum of selected column is                   160.00000
 The number of points used in calculation is              438
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   66960.000
 The mean of the selected column is                  152.87671
 The standard deviation of the selected column is    1.1232334
 The minimum of selected column is                   150.00000
 The maximum of selected column is                   156.00000
 The number of points used in calculation is              438
-> Converting (153.0,47.0,2.0) to g3 detector coordinates
-> Using events in: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   10009.000
 The mean of the selected column is                  77.589147
 The standard deviation of the selected column is    1.1498125
 The minimum of selected column is                   75.000000
 The maximum of selected column is                   80.000000
 The number of points used in calculation is              129
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   7712.0000
 The mean of the selected column is                  59.782946
 The standard deviation of the selected column is    1.1107517
 The minimum of selected column is                   57.000000
 The maximum of selected column is                   62.000000
 The number of points used in calculation is              129

Extracting spectra and generating response matrices ( 10:15:51 )

-> Fetching xrt_ea_v2_0.fits
-> Fetching xrt_psf_v2_0.fits
-> sisph2pi_110397.fits already present in current directory
-> Fetching sisechos_290296.fits
-> Fetching sisrddis_290296.fits
-> Standard Output From STOOL group_event_files:
1 ad63007000s000102h.evt 71373
1 ad63007000s000202m.evt 71373
1 ad63007000s000502l.evt 71373
2 ad63007000s000402h.evt 2114
3 ad63007000s000302h.evt 1310
3 ad63007000s000602m.evt 1310
-> Fetching SIS0_OFFCHIP.1
-> Extracting ad63007000s010102_1.pi from ad63007000s032002_1.reg and:
ad63007000s000102h.evt
ad63007000s000202m.evt
ad63007000s000502l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      6849          38176         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      4166          22094         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373     11015          60358         0         0         0
   in   75836.68 seconds
 Spectrum         has    11015 counts for 0.1452     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      6849          38176         0         0         0
 Writing events file
   6849 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      4166          22094         0         0         0
 Writing events file
  11015 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
  11015 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373     11015          60358         0         0         0
   in   75836.68 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010102_1.pi group=yes
Wrote spectrum to ad63007000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad63007000s010102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      25  are grouped by a factor       13
 ...        26 -      88  are single channels
 ...        89 -      90  are grouped by a factor        2
 ...        91 -      95  are single channels
 ...        96 -      97  are grouped by a factor        2
 ...        98 -      99  are single channels
 ...       100 -     101  are grouped by a factor        2
 ...       102 -     106  are single channels
 ...       107 -     108  are grouped by a factor        2
 ...       109 -     112  are single channels
 ...       113 -     114  are grouped by a factor        2
 ...       115 -     116  are single channels
 ...       117 -     118  are grouped by a factor        2
 ...       119 -     119  are single channels
 ...       120 -     129  are grouped by a factor        2
 ...       130 -     130  are single channels
 ...       131 -     156  are grouped by a factor        2
 ...       157 -     159  are grouped by a factor        3
 ...       160 -     161  are grouped by a factor        2
 ...       162 -     173  are grouped by a factor        3
 ...       174 -     185  are grouped by a factor        4
 ...       186 -     188  are grouped by a factor        3
 ...       189 -     193  are grouped by a factor        5
 ...       194 -     197  are grouped by a factor        4
 ...       198 -     203  are grouped by a factor        6
 ...       204 -     212  are grouped by a factor        9
 ...       213 -     220  are grouped by a factor        8
 ...       221 -     233  are grouped by a factor       13
 ...       234 -     245  are grouped by a factor       12
 ...       246 -     271  are grouped by a factor       26
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1 2
-> Fetching SIS0_NOTCHIP2.1
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 23:22:14 0.76E+05    11015 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          11015      2028           8987         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11015      2028           8987         0         0         0
   in   75836.68 seconds
 Spectrum         has     2028 counts for 2.6742E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 5.38086E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fits
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Fetching SIS0_NOTCHIP1.1
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 23:22:14 0.76E+05    11015 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          11015      8987           2028         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11015      8987           2028         0         0         0
   in   75836.68 seconds
 Spectrum         has     8987 counts for 0.1185     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.86133E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fits
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C2 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Chip weights:
rmf1.tmp 0.18411257376305
rmf2.tmp 0.81588742623695
-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10  10 April, 1997.
Summing ...
 1.841E-01 * rmf1.tmp
 8.159E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.18
              ASCA       SIS0       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.82
              ASCA       SIS0       NONE       NONE       PI
-> Generating ad63007000s010102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   27 bins
               expanded to   31 by   27 bins
 First WMAP bin is at detector pixel  576  208
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   27.649     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  703.00  319.00 (detector coordinates)
 Point source at   -5.03   30.00 (WMAP bins wrt optical axis)
 Point source at    6.45   99.53 (... in polar coordinates)
 
 Total counts in region = 1.09450E+04
 Weighted mean angle from optical axis  =  6.803 arcmin
-> Extracting ad63007000s010102_2.pi from ad63007000s032002_2.reg and:
ad63007000s000102h.evt
ad63007000s000202m.evt
ad63007000s000502l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     12690          32335         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      7322          18938         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         6             82         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373     20018          51355         0         0         0
   in   75836.68 seconds
 Spectrum         has    20018 counts for 0.2640     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     12690          32335         0         0         0
 Writing events file
  12690 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      7322          18938         0         0         0
 Writing events file
  20012 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         6             82         0         0         0
 Writing events file
  20018 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373     20018          51355         0         0         0
   in   75836.68 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010102_2.pi group=yes
Wrote spectrum to ad63007000s010102_2.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad63007000s010102_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      24  are grouped by a factor       12
 ...        25 -     132  are single channels
 ...       133 -     134  are grouped by a factor        2
 ...       135 -     136  are single channels
 ...       137 -     140  are grouped by a factor        2
 ...       141 -     141  are single channels
 ...       142 -     145  are grouped by a factor        2
 ...       146 -     147  are single channels
 ...       148 -     153  are grouped by a factor        2
 ...       154 -     154  are single channels
 ...       155 -     156  are grouped by a factor        2
 ...       157 -     157  are single channels
 ...       158 -     169  are grouped by a factor        2
 ...       170 -     172  are grouped by a factor        3
 ...       173 -     174  are grouped by a factor        2
 ...       175 -     180  are grouped by a factor        3
 ...       181 -     182  are grouped by a factor        2
 ...       183 -     194  are grouped by a factor        3
 ...       195 -     202  are grouped by a factor        4
 ...       203 -     212  are grouped by a factor        5
 ...       213 -     218  are grouped by a factor        6
 ...       219 -     228  are grouped by a factor        5
 ...       229 -     246  are grouped by a factor        9
 ...       247 -     261  are grouped by a factor       15
 ...       262 -     275  are grouped by a factor       14
 ...       276 -     319  are grouped by a factor       44
 ...       320 -     399  are grouped by a factor       80
 ...       400 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010102_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010102_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   30 bins
               expanded to   31 by   30 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.99730E+04
 Weighted mean angle from optical axis  =  5.941 arcmin
-> Extracting ad63007000s010102_3.pi from ad63007000s032002_3.reg and:
ad63007000s000102h.evt
ad63007000s000202m.evt
ad63007000s000502l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      2336          42689         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      1421          24839         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         1             87         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373      3758          67615         0         0         0
   in   75836.68 seconds
 Spectrum         has     3758 counts for 4.9554E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      2336          42689         0         0         0
 Writing events file
   2336 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      1421          24839         0         0         0
 Writing events file
   3757 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         1             87         0         0         0
 Writing events file
   3758 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373      3758          67615         0         0         0
   in   75836.68 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010102_3.pi group=yes
Wrote spectrum to ad63007000s010102_3.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad63007000s010102_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      28  are grouped by a factor       16
 ...        29 -      31  are grouped by a factor        3
 ...        32 -      39  are grouped by a factor        2
 ...        40 -      40  are single channels
 ...        41 -      42  are grouped by a factor        2
 ...        43 -      53  are single channels
 ...        54 -      55  are grouped by a factor        2
 ...        56 -      62  are single channels
 ...        63 -      64  are grouped by a factor        2
 ...        65 -      65  are single channels
 ...        66 -      67  are grouped by a factor        2
 ...        68 -      68  are single channels
 ...        69 -      80  are grouped by a factor        2
 ...        81 -      83  are grouped by a factor        3
 ...        84 -      85  are grouped by a factor        2
 ...        86 -      97  are grouped by a factor        3
 ...        98 -      99  are grouped by a factor        2
 ...       100 -     120  are grouped by a factor        3
 ...       121 -     122  are grouped by a factor        2
 ...       123 -     128  are grouped by a factor        3
 ...       129 -     132  are grouped by a factor        4
 ...       133 -     135  are grouped by a factor        3
 ...       136 -     143  are grouped by a factor        4
 ...       144 -     149  are grouped by a factor        6
 ...       150 -     153  are grouped by a factor        4
 ...       154 -     177  are grouped by a factor        6
 ...       178 -     185  are grouped by a factor        8
 ...       186 -     207  are grouped by a factor       11
 ...       208 -     219  are grouped by a factor       12
 ...       220 -     244  are grouped by a factor       25
 ...       245 -     323  are grouped by a factor       79
 ...       324 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_3.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> Fetching sis0c3p40_290296.fits
-> Generating ad63007000s010102_3.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C3 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010102_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   26 by   26 bins
               expanded to   26 by   26 bins
 First WMAP bin is at detector pixel  784  744
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   23.372     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  891.00  851.00 (detector coordinates)
 Point source at  -28.53  -36.50 (WMAP bins wrt optical axis)
 Point source at    9.83  231.98 (... in polar coordinates)
 
 Total counts in region = 3.72100E+03
 Weighted mean angle from optical axis  =  9.707 arcmin
-> Extracting ad63007000s010102_4.pi from ad63007000s032002_4.reg and:
ad63007000s000102h.evt
ad63007000s000202m.evt
ad63007000s000502l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025       615          44410         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260       386          25874         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373      1001          70372         0         0         0
   in   75836.68 seconds
 Spectrum         has     1001 counts for 1.3199E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025       615          44410         0         0         0
 Writing events file
    615 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260       386          25874         0         0         0
 Writing events file
   1001 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
   1001 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         71373      1001          70372         0         0         0
   in   75836.68 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010102_4.pi group=yes
Wrote spectrum to ad63007000s010102_4.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad63007000s010102_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 75837.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      27  are grouped by a factor       15
 ...        28 -      31  are grouped by a factor        4
 ...        32 -      33  are grouped by a factor        2
 ...        34 -      39  are grouped by a factor        3
 ...        40 -      41  are grouped by a factor        2
 ...        42 -      47  are grouped by a factor        3
 ...        48 -      49  are grouped by a factor        2
 ...        50 -      52  are grouped by a factor        3
 ...        53 -      54  are grouped by a factor        2
 ...        55 -      59  are grouped by a factor        5
 ...        60 -      63  are grouped by a factor        4
 ...        64 -      73  are grouped by a factor        5
 ...        74 -      81  are grouped by a factor        8
 ...        82 -      91  are grouped by a factor       10
 ...        92 -     102  are grouped by a factor       11
 ...       103 -     118  are grouped by a factor       16
 ...       119 -     136  are grouped by a factor       18
 ...       137 -     164  are grouped by a factor       28
 ...       165 -     312  are grouped by a factor      148
 ...       313 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010102_4.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010102_4.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010102_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size    8 by    8 bins
               expanded to    8 by    8 bins
 First WMAP bin is at detector pixel  480  544
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   2.0818     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  515.00  579.00 (detector coordinates)
 Point source at   18.47   -2.50 (WMAP bins wrt optical axis)
 Point source at    3.95  352.30 (... in polar coordinates)
 
 Total counts in region = 9.90000E+02
 Weighted mean angle from optical axis  =  4.030 arcmin
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s010202_1.pi from ad63007000s032002_1.reg and:
ad63007000s000402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       359           1755         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       359           1755         0         0         0
   in    2301.77 seconds
 Spectrum         has      359 counts for 0.1560     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010202_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       359           1755         0         0         0
 Writing events file
    359 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       359           1755         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010202_1.pi group=yes
Wrote spectrum to ad63007000s010202_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010202_1.pi since it has 359 events
-> Extracting ad63007000s010202_2.pi from ad63007000s032002_2.reg and:
ad63007000s000402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       589           1525         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       589           1525         0         0         0
   in    2301.77 seconds
 Spectrum         has      589 counts for 0.2559     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010202_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       589           1525         0         0         0
 Writing events file
    589 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       589           1525         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010202_2.pi group=yes
Wrote spectrum to ad63007000s010202_2.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad63007000s010202_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      30  are grouped by a factor       18
 ...        31 -      54  are grouped by a factor        4
 ...        55 -      59  are grouped by a factor        5
 ...        60 -      68  are grouped by a factor        9
 ...        69 -      83  are grouped by a factor       15
 ...        84 -     109  are grouped by a factor       26
 ...       110 -     133  are grouped by a factor       24
 ...       134 -     171  are grouped by a factor       38
 ...       172 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010202_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010202_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010202_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   30 bins
               expanded to   31 by   30 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 5.74000E+02
 Weighted mean angle from optical axis  =  5.968 arcmin
-> Extracting ad63007000s010202_3.pi from ad63007000s032002_3.reg and:
ad63007000s000402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       112           2002         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       112           2002         0         0         0
   in    2301.77 seconds
 Spectrum         has      112 counts for 4.8658E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010202_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       112           2002         0         0         0
 Writing events file
    112 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       112           2002         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010202_3.pi group=yes
Wrote spectrum to ad63007000s010202_3.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010202_3.pi since it has 112 events
-> Extracting ad63007000s010202_4.pi from ad63007000s032002_4.reg and:
ad63007000s000402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114        33           2081         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114        33           2081         0         0         0
   in    2301.77 seconds
 Spectrum         has       33 counts for 1.4337E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010202_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114        33           2081         0         0         0
 Writing events file
     33 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114        33           2081         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010202_4.pi group=yes
Wrote spectrum to ad63007000s010202_4.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010202_4.pi since it has 33 events
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s010302_1.pi from ad63007000s032002_1.reg and:
ad63007000s000302h.evt
ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        69            821         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        53            367         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310       122           1188         0         0         0
   in    2457.66 seconds
 Spectrum         has      122 counts for 4.9641E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2457.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010302_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        69            821         0         0         0
 Writing events file
     69 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        53            367         0         0         0
 Writing events file
    122 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310       122           1188         0         0         0
   in    2457.66 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010302.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010302_1.pi group=yes
Wrote spectrum to ad63007000s010302_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010302_1.pi since it has 122 events
-> Extracting ad63007000s010302_2.pi from ad63007000s032002_2.reg and:
ad63007000s000302h.evt
ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       219            671         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       108            312         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310       327            983         0         0         0
   in    2457.66 seconds
 Spectrum         has      327 counts for 0.1331     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2457.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010302_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       219            671         0         0         0
 Writing events file
    219 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       108            312         0         0         0
 Writing events file
    327 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310       327            983         0         0         0
   in    2457.66 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010302.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010302_2.pi group=yes
Wrote spectrum to ad63007000s010302_2.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010302_2.pi since it has 327 events
-> Extracting ad63007000s010302_3.pi from ad63007000s032002_3.reg and:
ad63007000s000302h.evt
ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        57            833         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        26            394         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310        83           1227         0         0         0
   in    2457.66 seconds
 Spectrum         has       83 counts for 3.3772E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2457.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010302_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        57            833         0         0         0
 Writing events file
     57 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        26            394         0         0         0
 Writing events file
     83 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310        83           1227         0         0         0
   in    2457.66 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010302.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010302_3.pi group=yes
Wrote spectrum to ad63007000s010302_3.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010302_3.pi since it has 83 events
-> Extracting ad63007000s010302_4.pi from ad63007000s032002_4.reg and:
ad63007000s000302h.evt
ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        19            871         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420         5            415         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310        24           1286         0         0         0
   in    2457.66 seconds
 Spectrum         has       24 counts for 9.7654E-03 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2457.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010302_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        19            871         0         0         0
 Writing events file
     19 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420         5            415         0         0         0
 Writing events file
     24 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1310        24           1286         0         0         0
   in    2457.66 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s010302.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad63007000s010302_4.pi group=yes
Wrote spectrum to ad63007000s010302_4.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s010302_4.pi since it has 24 events
-> Standard Output From STOOL group_event_files:
1 ad63007000s000112h.evt 50310
2 ad63007000s000412h.evt 2373
3 ad63007000s000312h.evt 1091
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s010412_1.pi from ad63007000s032002_1.reg and:
ad63007000s000112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      7714          42596         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      7714          42596         0         0         0
   in   47221.93 seconds
 Spectrum         has     7714 counts for 0.1634     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      7714          42596         0         0         0
 Writing events file
   7714 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      7714          42596         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010412_1.pi group=yes
Wrote spectrum to ad63007000s010412_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s010412_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      50  are grouped by a factor       25
 ...        51 -      53  are grouped by a factor        3
 ...        54 -      65  are grouped by a factor        2
 ...        66 -      67  are single channels
 ...        68 -      69  are grouped by a factor        2
 ...        70 -      78  are single channels
 ...        79 -      80  are grouped by a factor        2
 ...        81 -     120  are single channels
 ...       121 -     122  are grouped by a factor        2
 ...       123 -     126  are single channels
 ...       127 -     132  are grouped by a factor        2
 ...       133 -     133  are single channels
 ...       134 -     159  are grouped by a factor        2
 ...       160 -     162  are grouped by a factor        3
 ...       163 -     166  are grouped by a factor        2
 ...       167 -     169  are grouped by a factor        3
 ...       170 -     171  are grouped by a factor        2
 ...       172 -     174  are grouped by a factor        3
 ...       175 -     176  are grouped by a factor        2
 ...       177 -     182  are grouped by a factor        3
 ...       183 -     184  are grouped by a factor        2
 ...       185 -     187  are grouped by a factor        3
 ...       188 -     189  are grouped by a factor        2
 ...       190 -     237  are grouped by a factor        3
 ...       238 -     257  are grouped by a factor        4
 ...       258 -     260  are grouped by a factor        3
 ...       261 -     265  are grouped by a factor        5
 ...       266 -     277  are grouped by a factor        4
 ...       278 -     282  are grouped by a factor        5
 ...       283 -     288  are grouped by a factor        6
 ...       289 -     292  are grouped by a factor        4
 ...       293 -     302  are grouped by a factor        5
 ...       303 -     308  are grouped by a factor        6
 ...       309 -     313  are grouped by a factor        5
 ...       314 -     319  are grouped by a factor        6
 ...       320 -     326  are grouped by a factor        7
 ...       327 -     334  are grouped by a factor        8
 ...       335 -     343  are grouped by a factor        9
 ...       344 -     351  are grouped by a factor        8
 ...       352 -     362  are grouped by a factor       11
 ...       363 -     370  are grouped by a factor        8
 ...       371 -     390  are grouped by a factor       10
 ...       391 -     403  are grouped by a factor       13
 ...       404 -     449  are grouped by a factor       23
 ...       450 -     482  are grouped by a factor       33
 ...       483 -     533  are grouped by a factor       51
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1 2
-> SIS0_NOTCHIP2.1 already present in current directory
-> Extracting spectrum from chip 1
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05     7714 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           7714      1428           6286         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7714      1428           6286         0         0         0
   in   47221.93 seconds
 Spectrum         has     1428 counts for 3.0240E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 5.38086E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec1.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directory
-> Generating RMF for chip 1
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> SIS0_NOTCHIP1.1 already present in current directory
-> Extracting spectrum from chip 2
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05     7714 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           7714      6286           1428         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7714      6286           1428         0         0         0
   in   47221.93 seconds
 Spectrum         has     6286 counts for 0.1331     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.86133E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec2.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directory
-> Generating RMF for chip 2
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C2 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Chip weights:
rmf1.tmp 0.185117967332123
rmf2.tmp 0.814882032667877
-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10  10 April, 1997.
Summing ...
 1.851E-01 * rmf1.tmp
 8.149E-01 * rmf2.tmp
 RMF #    1 : rmf1.tmp                   0.19
              ASCA       SIS0       NONE       NONE       PI
 RMF #    2 : rmf2.tmp                   0.81
              ASCA       SIS0       NONE       NONE       PI
-> Generating ad63007000s010412_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   27 bins
               expanded to   31 by   27 bins
 First WMAP bin is at detector pixel  576  208
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   27.649     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  703.00  319.00 (detector coordinates)
 Point source at   -5.03   30.00 (WMAP bins wrt optical axis)
 Point source at    6.45   99.53 (... in polar coordinates)
 
 Total counts in region = 7.64600E+03
 Weighted mean angle from optical axis  =  6.809 arcmin
-> Extracting ad63007000s010412_2.pi from ad63007000s032002_2.reg and:
ad63007000s000112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310     13974          36336         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310     13974          36336         0         0         0
   in   47221.93 seconds
 Spectrum         has    13974 counts for 0.2959     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310     13974          36336         0         0         0
 Writing events file
  13974 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310     13974          36336         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010412_2.pi group=yes
Wrote spectrum to ad63007000s010412_2.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s010412_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      48  are grouped by a factor       23
 ...        49 -     143  are single channels
 ...       144 -     145  are grouped by a factor        2
 ...       146 -     148  are single channels
 ...       149 -     150  are grouped by a factor        2
 ...       151 -     151  are single channels
 ...       152 -     153  are grouped by a factor        2
 ...       154 -     155  are single channels
 ...       156 -     173  are grouped by a factor        2
 ...       174 -     174  are single channels
 ...       175 -     216  are grouped by a factor        2
 ...       217 -     222  are grouped by a factor        3
 ...       223 -     226  are grouped by a factor        2
 ...       227 -     232  are grouped by a factor        3
 ...       233 -     236  are grouped by a factor        2
 ...       237 -     239  are grouped by a factor        3
 ...       240 -     241  are grouped by a factor        2
 ...       242 -     253  are grouped by a factor        3
 ...       254 -     255  are grouped by a factor        2
 ...       256 -     282  are grouped by a factor        3
 ...       283 -     290  are grouped by a factor        4
 ...       291 -     293  are grouped by a factor        3
 ...       294 -     305  are grouped by a factor        4
 ...       306 -     310  are grouped by a factor        5
 ...       311 -     318  are grouped by a factor        4
 ...       319 -     323  are grouped by a factor        5
 ...       324 -     326  are grouped by a factor        3
 ...       327 -     330  are grouped by a factor        4
 ...       331 -     335  are grouped by a factor        5
 ...       336 -     359  are grouped by a factor        6
 ...       360 -     380  are grouped by a factor        7
 ...       381 -     388  are grouped by a factor        8
 ...       389 -     397  are grouped by a factor        9
 ...       398 -     408  are grouped by a factor       11
 ...       409 -     422  are grouped by a factor       14
 ...       423 -     435  are grouped by a factor       13
 ...       436 -     451  are grouped by a factor       16
 ...       452 -     465  are grouped by a factor       14
 ...       466 -     487  are grouped by a factor       22
 ...       488 -     522  are grouped by a factor       35
 ...       523 -     575  are grouped by a factor       53
 ...       576 -     738  are grouped by a factor      163
 ...       739 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010412_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010412_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   30 bins
               expanded to   31 by   30 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.39290E+04
 Weighted mean angle from optical axis  =  5.940 arcmin
-> Extracting ad63007000s010412_3.pi from ad63007000s032002_3.reg and:
ad63007000s000112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      2679          47631         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      2679          47631         0         0         0
   in   47221.93 seconds
 Spectrum         has     2679 counts for 5.6732E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      2679          47631         0         0         0
 Writing events file
   2679 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      2679          47631         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010412_3.pi group=yes
Wrote spectrum to ad63007000s010412_3.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s010412_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      55  are grouped by a factor       30
 ...        56 -      61  are grouped by a factor        6
 ...        62 -      66  are grouped by a factor        5
 ...        67 -      74  are grouped by a factor        4
 ...        75 -      83  are grouped by a factor        3
 ...        84 -      85  are grouped by a factor        2
 ...        86 -      88  are grouped by a factor        3
 ...        89 -      92  are grouped by a factor        2
 ...        93 -      98  are grouped by a factor        3
 ...        99 -     104  are grouped by a factor        2
 ...       105 -     107  are grouped by a factor        3
 ...       108 -     113  are grouped by a factor        2
 ...       114 -     122  are grouped by a factor        3
 ...       123 -     126  are grouped by a factor        4
 ...       127 -     135  are grouped by a factor        3
 ...       136 -     140  are grouped by a factor        5
 ...       141 -     152  are grouped by a factor        4
 ...       153 -     158  are grouped by a factor        6
 ...       159 -     163  are grouped by a factor        5
 ...       164 -     169  are grouped by a factor        6
 ...       170 -     183  are grouped by a factor        7
 ...       184 -     191  are grouped by a factor        8
 ...       192 -     196  are grouped by a factor        5
 ...       197 -     210  are grouped by a factor        7
 ...       211 -     218  are grouped by a factor        8
 ...       219 -     224  are grouped by a factor        6
 ...       225 -     238  are grouped by a factor        7
 ...       239 -     246  are grouped by a factor        8
 ...       247 -     252  are grouped by a factor        6
 ...       253 -     264  are grouped by a factor       12
 ...       265 -     272  are grouped by a factor        8
 ...       273 -     284  are grouped by a factor       12
 ...       285 -     298  are grouped by a factor       14
 ...       299 -     309  are grouped by a factor       11
 ...       310 -     322  are grouped by a factor       13
 ...       323 -     339  are grouped by a factor       17
 ...       340 -     355  are grouped by a factor       16
 ...       356 -     378  are grouped by a factor       23
 ...       379 -     410  are grouped by a factor       32
 ...       411 -     447  are grouped by a factor       37
 ...       448 -     495  are grouped by a factor       48
 ...       496 -     777  are grouped by a factor      282
 ...       778 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_3.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis0c3p40_290296.fits already present in current directory
-> Generating ad63007000s010412_3.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C3 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010412_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   26 by   26 bins
               expanded to   26 by   26 bins
 First WMAP bin is at detector pixel  784  744
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   23.372     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  891.00  851.00 (detector coordinates)
 Point source at  -28.53  -36.50 (WMAP bins wrt optical axis)
 Point source at    9.83  231.98 (... in polar coordinates)
 
 Total counts in region = 2.64800E+03
 Weighted mean angle from optical axis  =  9.718 arcmin
-> Extracting ad63007000s010412_4.pi from ad63007000s032002_4.reg and:
ad63007000s000112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310       661          49649         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310       661          49649         0         0         0
   in   47221.93 seconds
 Spectrum         has      661 counts for 1.3998E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310       661          49649         0         0         0
 Writing events file
    661 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310       661          49649         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010412_4.pi group=yes
Wrote spectrum to ad63007000s010412_4.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s010412_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 47222.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      56  are grouped by a factor       31
 ...        57 -      65  are grouped by a factor        9
 ...        66 -      79  are grouped by a factor        7
 ...        80 -      87  are grouped by a factor        8
 ...        88 -      93  are grouped by a factor        6
 ...        94 -     101  are grouped by a factor        8
 ...       102 -     108  are grouped by a factor        7
 ...       109 -     144  are grouped by a factor       12
 ...       145 -     172  are grouped by a factor       28
 ...       173 -     205  are grouped by a factor       33
 ...       206 -     261  are grouped by a factor       56
 ...       262 -     364  are grouped by a factor      103
 ...       365 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010412_4.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010412_4.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010412_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size    8 by    8 bins
               expanded to    8 by    8 bins
 First WMAP bin is at detector pixel  480  544
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   2.0818     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  515.00  579.00 (detector coordinates)
 Point source at   18.47   -2.50 (WMAP bins wrt optical axis)
 Point source at    3.95  352.30 (... in polar coordinates)
 
 Total counts in region = 6.50000E+02
 Weighted mean angle from optical axis  =  4.038 arcmin
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s010512_1.pi from ad63007000s032002_1.reg and:
ad63007000s000412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       407           1966         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       407           1966         0         0         0
   in    2301.77 seconds
 Spectrum         has      407 counts for 0.1768     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010512_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       407           1966         0         0         0
 Writing events file
    407 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       407           1966         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010512.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010512_1.pi group=yes
Wrote spectrum to ad63007000s010512_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010512_1.pi since it has 407 events
-> Extracting ad63007000s010512_2.pi from ad63007000s032002_2.reg and:
ad63007000s000412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       643           1730         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       643           1730         0         0         0
   in    2301.77 seconds
 Spectrum         has      643 counts for 0.2794     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010512_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       643           1730         0         0         0
 Writing events file
    643 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       643           1730         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010512.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010512_2.pi group=yes
Wrote spectrum to ad63007000s010512_2.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s010512_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      58  are grouped by a factor       33
 ...        59 -      79  are grouped by a factor        7
 ...        80 -      85  are grouped by a factor        6
 ...        86 -      92  are grouped by a factor        7
 ...        93 -     108  are grouped by a factor        8
 ...       109 -     118  are grouped by a factor       10
 ...       119 -     136  are grouped by a factor       18
 ...       137 -     163  are grouped by a factor       27
 ...       164 -     208  are grouped by a factor       45
 ...       209 -     252  are grouped by a factor       44
 ...       253 -     314  are grouped by a factor       62
 ...       315 -     415  are grouped by a factor      101
 ...       416 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010512_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad63007000s010512_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s010512_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   30 bins
               expanded to   31 by   30 bins
 First WMAP bin is at detector pixel  360  312
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 6.27000E+02
 Weighted mean angle from optical axis  =  5.947 arcmin
-> Extracting ad63007000s010512_3.pi from ad63007000s032002_3.reg and:
ad63007000s000412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       122           2251         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       122           2251         0         0         0
   in    2301.77 seconds
 Spectrum         has      122 counts for 5.3003E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010512_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       122           2251         0         0         0
 Writing events file
    122 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       122           2251         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010512.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010512_3.pi group=yes
Wrote spectrum to ad63007000s010512_3.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010512_3.pi since it has 122 events
-> Extracting ad63007000s010512_4.pi from ad63007000s032002_4.reg and:
ad63007000s000412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373        38           2335         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373        38           2335         0         0         0
   in    2301.77 seconds
 Spectrum         has       38 counts for 1.6509E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 2301.8          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010512_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373        38           2335         0         0         0
 Writing events file
     38 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373        38           2335         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010512.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010512_4.pi group=yes
Wrote spectrum to ad63007000s010512_4.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010512_4.pi since it has 38 events
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s010612_1.pi from ad63007000s032002_1.reg and:
ad63007000s000312h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        95            996         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        95            996         0         0         0
   in    1007.30 seconds
 Spectrum         has       95 counts for 9.4312E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1007.3          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.39941E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010612_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        95            996         0         0         0
 Writing events file
     95 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        95            996         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010612.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010612_1.pi group=yes
Wrote spectrum to ad63007000s010612_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010612_1.pi since it has 95 events
-> Extracting ad63007000s010612_2.pi from ad63007000s032002_2.reg and:
ad63007000s000312h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091       273            818         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091       273            818         0         0         0
   in    1007.30 seconds
 Spectrum         has      273 counts for 0.2710     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1007.3          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010612_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091       273            818         0         0         0
 Writing events file
    273 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091       273            818         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010612.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010612_2.pi group=yes
Wrote spectrum to ad63007000s010612_2.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010612_2.pi since it has 273 events
-> Extracting ad63007000s010612_3.pi from ad63007000s032002_3.reg and:
ad63007000s000312h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        64           1027         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        64           1027         0         0         0
   in    1007.30 seconds
 Spectrum         has       64 counts for 6.3536E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1007.3          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010612_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        64           1027         0         0         0
 Writing events file
     64 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        64           1027         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010612.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010612_3.pi group=yes
Wrote spectrum to ad63007000s010612_3.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010612_3.pi since it has 64 events
-> Extracting ad63007000s010612_4.pi from ad63007000s032002_4.reg and:
ad63007000s000312h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        22           1069         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        22           1069         0         0         0
   in    1007.30 seconds
 Spectrum         has       22 counts for 2.1841E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1007.3          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.80664E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s010612_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        22           1069         0         0         0
 Writing events file
     22 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        22           1069         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s010612.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad63007000s010612_4.pi group=yes
Wrote spectrum to ad63007000s010612_4.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s010612_4.pi since it has 22 events
-> Standard Output From STOOL group_event_files:
1 ad63007000s100102h.evt 56153
1 ad63007000s100202m.evt 56153
1 ad63007000s100302l.evt 56153
2 ad63007000s100402h.evt 702
-> Fetching SIS1_OFFCHIP.1
-> Extracting ad63007000s110102_1.pi from ad63007000s132002_1.reg and:
ad63007000s100102h.evt
ad63007000s100202m.evt
ad63007000s100302l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      4200          31397         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      2514          17941         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         3             98         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153      6717          49436         0         0         0
   in   81591.27 seconds
 Spectrum         has     6717 counts for 8.2325E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.74121E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      4200          31397         0         0         0
 Writing events file
   4200 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      2514          17941         0         0         0
 Writing events file
   6714 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         3             98         0         0         0
 Writing events file
   6717 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153      6717          49436         0         0         0
   in   81591.27 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad63007000s110102_1.pi group=yes
Wrote spectrum to ad63007000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad63007000s110102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.74121E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      31  are grouped by a factor       19
 ...        32 -      82  are single channels
 ...        83 -      84  are grouped by a factor        2
 ...        85 -      85  are single channels
 ...        86 -      93  are grouped by a factor        2
 ...        94 -      94  are single channels
 ...        95 -     122  are grouped by a factor        2
 ...       123 -     128  are grouped by a factor        3
 ...       129 -     130  are grouped by a factor        2
 ...       131 -     133  are grouped by a factor        3
 ...       134 -     135  are grouped by a factor        2
 ...       136 -     141  are grouped by a factor        3
 ...       142 -     145  are grouped by a factor        2
 ...       146 -     151  are grouped by a factor        3
 ...       152 -     163  are grouped by a factor        4
 ...       164 -     166  are grouped by a factor        3
 ...       167 -     174  are grouped by a factor        4
 ...       175 -     184  are grouped by a factor        5
 ...       185 -     190  are grouped by a factor        6
 ...       191 -     204  are grouped by a factor        7
 ...       205 -     213  are grouped by a factor        9
 ...       214 -     223  are grouped by a factor       10
 ...       224 -     243  are grouped by a factor       20
 ...       244 -     273  are grouped by a factor       30
 ...       274 -     386  are grouped by a factor      113
 ...       387 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 0 3
-> Fetching SIS1_NOTCHIP3.1
-> Extracting spectrum from chip 0
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.82E+05     6717 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           6717      5056           1661         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6717      5056           1661         0         0         0
   in   81591.27 seconds
 Spectrum         has     5056 counts for 6.1967E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.08008E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec0.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fits
-> Generating RMF for chip 0
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C0 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Fetching SIS1_NOTCHIP0.1
-> Extracting spectrum from chip 3
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.82E+05     6717 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           6717      1661           5056         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6717      1661           5056         0         0         0
   in   81591.27 seconds
 Spectrum         has     1661 counts for 2.0358E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 6.61133E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec3.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fits
-> Generating RMF for chip 3
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C3 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Chip weights:
rmf0.tmp 0.752716986750037
rmf3.tmp 0.247283013249963
-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10  10 April, 1997.
Summing ...
 7.527E-01 * rmf0.tmp
 2.473E-01 * rmf3.tmp
 RMF #    1 : rmf0.tmp                   0.75
              ASCA       SIS1       NONE       NONE       PI
 RMF #    2 : rmf3.tmp                   0.25
              ASCA       SIS1       NONE       NONE       PI
-> Generating ad63007000s110102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   32 by   30 bins
               expanded to   32 by   30 bins
 First WMAP bin is at detector pixel  568  216
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.587     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  699.00  339.00 (detector coordinates)
 Point source at  -10.09   54.35 (WMAP bins wrt optical axis)
 Point source at   11.73  100.52 (... in polar coordinates)
 
 Total counts in region = 6.65300E+03
 Weighted mean angle from optical axis  = 11.635 arcmin
-> Extracting ad63007000s110102_2.pi from ad63007000s132002_2.reg and:
ad63007000s100102h.evt
ad63007000s100202m.evt
ad63007000s100302l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      9050          26547         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      5027          15428         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153     14084          42069         0         0         0
   in   81591.27 seconds
 Spectrum         has    14084 counts for 0.1726     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      9050          26547         0         0         0
 Writing events file
   9050 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      5027          15428         0         0         0
 Writing events file
  14077 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
  14084 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153     14084          42069         0         0         0
   in   81591.27 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad63007000s110102_2.pi group=yes
Wrote spectrum to ad63007000s110102_2.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad63007000s110102_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      29  are grouped by a factor       17
 ...        30 -     108  are single channels
 ...       109 -     110  are grouped by a factor        2
 ...       111 -     113  are single channels
 ...       114 -     115  are grouped by a factor        2
 ...       116 -     118  are single channels
 ...       119 -     124  are grouped by a factor        2
 ...       125 -     125  are single channels
 ...       126 -     155  are grouped by a factor        2
 ...       156 -     158  are grouped by a factor        3
 ...       159 -     164  are grouped by a factor        2
 ...       165 -     173  are grouped by a factor        3
 ...       174 -     175  are grouped by a factor        2
 ...       176 -     179  are grouped by a factor        4
 ...       180 -     182  are grouped by a factor        3
 ...       183 -     194  are grouped by a factor        4
 ...       195 -     199  are grouped by a factor        5
 ...       200 -     205  are grouped by a factor        6
 ...       206 -     210  are grouped by a factor        5
 ...       211 -     217  are grouped by a factor        7
 ...       218 -     223  are grouped by a factor        6
 ...       224 -     232  are grouped by a factor        9
 ...       233 -     242  are grouped by a factor       10
 ...       243 -     258  are grouped by a factor       16
 ...       259 -     278  are grouped by a factor       20
 ...       279 -     314  are grouped by a factor       36
 ...       315 -     403  are grouped by a factor       89
 ...       404 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad63007000s110102_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C3 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110102_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   30 by   31 bins
               expanded to   30 by   31 bins
 First WMAP bin is at detector pixel  360  344
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.40400E+04
 Weighted mean angle from optical axis  =  8.778 arcmin
-> Extracting ad63007000s110102_3.pi from ad63007000s132002_3.reg and:
ad63007000s100102h.evt
ad63007000s100202m.evt
ad63007000s100302l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      2579          33018         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      1448          19007         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153      4034          52119         0         0         0
   in   81591.27 seconds
 Spectrum         has     4034 counts for 4.9442E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      2579          33018         0         0         0
 Writing events file
   2579 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      1448          19007         0         0         0
 Writing events file
   4027 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
   4034 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153      4034          52119         0         0         0
   in   81591.27 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad63007000s110102_3.pi group=yes
Wrote spectrum to ad63007000s110102_3.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad63007000s110102_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      31  are grouped by a factor       19
 ...        32 -      37  are grouped by a factor        2
 ...        38 -      65  are single channels
 ...        66 -      69  are grouped by a factor        2
 ...        70 -      70  are single channels
 ...        71 -      88  are grouped by a factor        2
 ...        89 -      94  are grouped by a factor        3
 ...        95 -      98  are grouped by a factor        2
 ...        99 -     104  are grouped by a factor        3
 ...       105 -     106  are grouped by a factor        2
 ...       107 -     112  are grouped by a factor        3
 ...       113 -     114  are grouped by a factor        2
 ...       115 -     117  are grouped by a factor        3
 ...       118 -     121  are grouped by a factor        2
 ...       122 -     127  are grouped by a factor        3
 ...       128 -     131  are grouped by a factor        4
 ...       132 -     134  are grouped by a factor        3
 ...       135 -     138  are grouped by a factor        4
 ...       139 -     141  are grouped by a factor        3
 ...       142 -     153  are grouped by a factor        4
 ...       154 -     158  are grouped by a factor        5
 ...       159 -     162  are grouped by a factor        4
 ...       163 -     172  are grouped by a factor        5
 ...       173 -     178  are grouped by a factor        6
 ...       179 -     186  are grouped by a factor        8
 ...       187 -     198  are grouped by a factor       12
 ...       199 -     211  are grouped by a factor       13
 ...       212 -     221  are grouped by a factor       10
 ...       222 -     233  are grouped by a factor       12
 ...       234 -     256  are grouped by a factor       23
 ...       257 -     292  are grouped by a factor       36
 ...       293 -     388  are grouped by a factor       96
 ...       389 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_3.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> Fetching sis1c1p40_290296.fits
-> Generating ad63007000s110102_3.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110102_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   26 by   27 bins
               expanded to   26 by   27 bins
 First WMAP bin is at detector pixel  784  776
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   23.372     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  891.00  887.00 (detector coordinates)
 Point source at  -34.09  -14.15 (WMAP bins wrt optical axis)
 Point source at    7.83  202.54 (... in polar coordinates)
 
 Total counts in region = 4.00100E+03
 Weighted mean angle from optical axis  =  7.596 arcmin
-> Extracting ad63007000s110102_4.pi from ad63007000s132002_4.reg and:
ad63007000s100102h.evt
ad63007000s100202m.evt
ad63007000s100302l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597       477          35120         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455       286          20169         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         0            101         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153       763          55390         0         0         0
   in   81591.27 seconds
 Spectrum         has      763 counts for 9.3515E-03 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.65039E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597       477          35120         0         0         0
 Writing events file
    477 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455       286          20169         0         0         0
 Writing events file
    763 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         0            101         0         0         0
 Writing events file
    763 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56153       763          55390         0         0         0
   in   81591.27 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad63007000s110102_4.pi group=yes
Wrote spectrum to ad63007000s110102_4.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad63007000s110102_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 81591.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.65039E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      12  of undefined grouping (Channel quality=bad)
 ...        13 -      33  are grouped by a factor       21
 ...        34 -      37  are grouped by a factor        4
 ...        38 -      40  are grouped by a factor        3
 ...        41 -      56  are grouped by a factor        4
 ...        57 -      66  are grouped by a factor        5
 ...        67 -      70  are grouped by a factor        4
 ...        71 -      77  are grouped by a factor        7
 ...        78 -      86  are grouped by a factor        9
 ...        87 -      96  are grouped by a factor       10
 ...        97 -     113  are grouped by a factor       17
 ...       114 -     134  are grouped by a factor       21
 ...       135 -     167  are grouped by a factor       33
 ...       168 -     383  are grouped by a factor      216
 ...       384 -     511  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110102_4.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad63007000s110102_4.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C3 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110102_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size    9 by    7 bins
               expanded to    9 by    7 bins
 First WMAP bin is at detector pixel  472  576
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   1.9018     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  511.00  607.00 (detector coordinates)
 Point source at   13.41   20.85 (WMAP bins wrt optical axis)
 Point source at    5.26   57.26 (... in polar coordinates)
 
 Total counts in region = 7.49000E+02
 Weighted mean angle from optical axis  =  5.312 arcmin
-> SIS1_NOTCHIP0.1 already present in current directory
-> SIS1_NOTCHIP3.1 already present in current directory
-> SIS1_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s110202_1.pi from ad63007000s132002_1.reg and:
ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702         0            702         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702         0            702         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110202_1.pi not extracted

-> Extracting ad63007000s110202_2.pi from ad63007000s132002_2.reg and:
ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702         0            702         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702         0            702         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110202_2.pi not extracted

-> Extracting ad63007000s110202_3.pi from ad63007000s132002_3.reg and:
ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        43            659         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702        43            659         0         0         0
   in    1001.72 seconds
 Spectrum         has       43 counts for 4.2926E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1001.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      12  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110202_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        43            659         0         0         0
 Writing events file
     43 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702        43            659         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad63007000s110202_3.pi group=yes
Wrote spectrum to ad63007000s110202_3.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s110202_3.pi since it has 43 events
-> Extracting ad63007000s110202_4.pi from ad63007000s132002_4.reg and:
ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702         0            702         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702         0            702         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110202_4.pi not extracted

-> Standard Output From STOOL group_event_files:
1 ad63007000s100112h.evt 42813
2 ad63007000s100412h.evt 835
-> SIS1_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s110312_1.pi from ad63007000s132002_1.reg and:
ad63007000s100112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      5219          37594         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      5219          37594         0         0         0
   in   50800.39 seconds
 Spectrum         has     5219 counts for 0.1027     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.74121E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_1.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      5219          37594         0         0         0
 Writing events file
   5219 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      5219          37594         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad63007000s110312_1.pi group=yes
Wrote spectrum to ad63007000s110312_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s110312_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.74121E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      60  are grouped by a factor       35
 ...        61 -      63  are grouped by a factor        3
 ...        64 -      65  are grouped by a factor        2
 ...        66 -      68  are grouped by a factor        3
 ...        69 -      78  are grouped by a factor        2
 ...        79 -      79  are single channels
 ...        80 -      81  are grouped by a factor        2
 ...        82 -      82  are single channels
 ...        83 -      84  are grouped by a factor        2
 ...        85 -      85  are single channels
 ...        86 -      87  are grouped by a factor        2
 ...        88 -      90  are single channels
 ...        91 -      92  are grouped by a factor        2
 ...        93 -      94  are single channels
 ...        95 -      98  are grouped by a factor        2
 ...        99 -     101  are single channels
 ...       102 -     103  are grouped by a factor        2
 ...       104 -     110  are single channels
 ...       111 -     112  are grouped by a factor        2
 ...       113 -     113  are single channels
 ...       114 -     141  are grouped by a factor        2
 ...       142 -     144  are grouped by a factor        3
 ...       145 -     150  are grouped by a factor        2
 ...       151 -     153  are grouped by a factor        3
 ...       154 -     161  are grouped by a factor        2
 ...       162 -     167  are grouped by a factor        3
 ...       168 -     187  are grouped by a factor        4
 ...       188 -     192  are grouped by a factor        5
 ...       193 -     208  are grouped by a factor        4
 ...       209 -     213  are grouped by a factor        5
 ...       214 -     221  are grouped by a factor        4
 ...       222 -     226  are grouped by a factor        5
 ...       227 -     230  are grouped by a factor        4
 ...       231 -     245  are grouped by a factor        5
 ...       246 -     252  are grouped by a factor        7
 ...       253 -     257  are grouped by a factor        5
 ...       258 -     264  are grouped by a factor        7
 ...       265 -     270  are grouped by a factor        6
 ...       271 -     277  are grouped by a factor        7
 ...       278 -     283  are grouped by a factor        6
 ...       284 -     287  are grouped by a factor        4
 ...       288 -     294  are grouped by a factor        7
 ...       295 -     300  are grouped by a factor        6
 ...       301 -     307  are grouped by a factor        7
 ...       308 -     316  are grouped by a factor        9
 ...       317 -     323  are grouped by a factor        7
 ...       324 -     331  are grouped by a factor        8
 ...       332 -     343  are grouped by a factor       12
 ...       344 -     354  are grouped by a factor       11
 ...       355 -     366  are grouped by a factor       12
 ...       367 -     381  are grouped by a factor       15
 ...       382 -     401  are grouped by a factor       20
 ...       402 -     419  are grouped by a factor       18
 ...       420 -     454  are grouped by a factor       35
 ...       455 -     504  are grouped by a factor       50
 ...       505 -     587  are grouped by a factor       83
 ...       588 -     884  are grouped by a factor      297
 ...       885 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 0 3
-> SIS1_NOTCHIP3.1 already present in current directory
-> Extracting spectrum from chip 0
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05     5219 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           5219      3963           1256         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5219      3963           1256         0         0         0
   in   50800.39 seconds
 Spectrum         has     3963 counts for 7.8011E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.08008E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec0.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directory
-> Generating RMF for chip 0
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C0 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> SIS1_NOTCHIP0.1 already present in current directory
-> Extracting spectrum from chip 3
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05     5219 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           5219      1256           3963         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          5219      1256           3963         0         0         0
   in   50800.39 seconds
 Spectrum         has     1256 counts for 2.4724E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 6.61133E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : spec3.tmp
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directory
-> Generating RMF for chip 3
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C3 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Chip weights:
rmf0.tmp 0.759340869898448
rmf3.tmp 0.240659130101552
-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10  10 April, 1997.
Summing ...
 7.593E-01 * rmf0.tmp
 2.407E-01 * rmf3.tmp
 RMF #    1 : rmf0.tmp                   0.76
              ASCA       SIS1       NONE       NONE       PI
 RMF #    2 : rmf3.tmp                   0.24
              ASCA       SIS1       NONE       NONE       PI
-> Generating ad63007000s110312_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   32 by   30 bins
               expanded to   32 by   30 bins
 First WMAP bin is at detector pixel  568  216
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.587     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  699.00  339.00 (detector coordinates)
 Point source at  -10.09   54.35 (WMAP bins wrt optical axis)
 Point source at   11.73  100.52 (... in polar coordinates)
 
 Total counts in region = 5.15900E+03
 Weighted mean angle from optical axis  = 11.646 arcmin
-> Extracting ad63007000s110312_2.pi from ad63007000s132002_2.reg and:
ad63007000s100112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813     10649          32164         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813     10649          32164         0         0         0
   in   50800.39 seconds
 Spectrum         has    10649 counts for 0.2096     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_2.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813     10649          32164         0         0         0
 Writing events file
  10649 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813     10649          32164         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad63007000s110312_2.pi group=yes
Wrote spectrum to ad63007000s110312_2.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s110312_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.69629E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      56  are grouped by a factor       31
 ...        57 -     128  are single channels
 ...       129 -     130  are grouped by a factor        2
 ...       131 -     135  are single channels
 ...       136 -     169  are grouped by a factor        2
 ...       170 -     172  are grouped by a factor        3
 ...       173 -     178  are grouped by a factor        2
 ...       179 -     181  are grouped by a factor        3
 ...       182 -     185  are grouped by a factor        2
 ...       186 -     188  are grouped by a factor        3
 ...       189 -     190  are grouped by a factor        2
 ...       191 -     193  are grouped by a factor        3
 ...       194 -     199  are grouped by a factor        2
 ...       200 -     205  are grouped by a factor        3
 ...       206 -     207  are grouped by a factor        2
 ...       208 -     219  are grouped by a factor        3
 ...       220 -     221  are grouped by a factor        2
 ...       222 -     230  are grouped by a factor        3
 ...       231 -     234  are grouped by a factor        4
 ...       235 -     240  are grouped by a factor        3
 ...       241 -     244  are grouped by a factor        4
 ...       245 -     246  are grouped by a factor        2
 ...       247 -     258  are grouped by a factor        3
 ...       259 -     262  are grouped by a factor        4
 ...       263 -     265  are grouped by a factor        3
 ...       266 -     269  are grouped by a factor        4
 ...       270 -     278  are grouped by a factor        3
 ...       279 -     282  are grouped by a factor        4
 ...       283 -     285  are grouped by a factor        3
 ...       286 -     310  are grouped by a factor        5
 ...       311 -     317  are grouped by a factor        7
 ...       318 -     323  are grouped by a factor        6
 ...       324 -     327  are grouped by a factor        4
 ...       328 -     332  are grouped by a factor        5
 ...       333 -     341  are grouped by a factor        9
 ...       342 -     346  are grouped by a factor        5
 ...       347 -     353  are grouped by a factor        7
 ...       354 -     362  are grouped by a factor        9
 ...       363 -     370  are grouped by a factor        8
 ...       371 -     379  are grouped by a factor        9
 ...       380 -     390  are grouped by a factor       11
 ...       391 -     400  are grouped by a factor       10
 ...       401 -     412  are grouped by a factor       12
 ...       413 -     429  are grouped by a factor       17
 ...       430 -     444  are grouped by a factor       15
 ...       445 -     464  are grouped by a factor       20
 ...       465 -     493  are grouped by a factor       29
 ...       494 -     553  are grouped by a factor       60
 ...       554 -     640  are grouped by a factor       87
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_2.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad63007000s110312_2.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C3 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110312_2.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   30 by   31 bins
               expanded to   30 by   31 bins
 First WMAP bin is at detector pixel  360  344
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   31.069     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 1.06090E+04
 Weighted mean angle from optical axis  =  8.793 arcmin
-> Extracting ad63007000s110312_3.pi from ad63007000s132002_3.reg and:
ad63007000s100112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      3062          39751         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      3062          39751         0         0         0
   in   50800.39 seconds
 Spectrum         has     3062 counts for 6.0275E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      3062          39751         0         0         0
 Writing events file
   3062 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      3062          39751         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad63007000s110312_3.pi group=yes
Wrote spectrum to ad63007000s110312_3.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s110312_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      60  are grouped by a factor       35
 ...        61 -      65  are grouped by a factor        5
 ...        66 -      83  are grouped by a factor        3
 ...        84 -      89  are grouped by a factor        2
 ...        90 -      95  are grouped by a factor        3
 ...        96 -     111  are grouped by a factor        2
 ...       112 -     114  are grouped by a factor        3
 ...       115 -     118  are grouped by a factor        2
 ...       119 -     130  are grouped by a factor        3
 ...       131 -     138  are grouped by a factor        4
 ...       139 -     141  are grouped by a factor        3
 ...       142 -     146  are grouped by a factor        5
 ...       147 -     158  are grouped by a factor        4
 ...       159 -     173  are grouped by a factor        5
 ...       174 -     179  are grouped by a factor        6
 ...       180 -     186  are grouped by a factor        7
 ...       187 -     192  are grouped by a factor        6
 ...       193 -     199  are grouped by a factor        7
 ...       200 -     205  are grouped by a factor        6
 ...       206 -     210  are grouped by a factor        5
 ...       211 -     217  are grouped by a factor        7
 ...       218 -     223  are grouped by a factor        6
 ...       224 -     230  are grouped by a factor        7
 ...       231 -     242  are grouped by a factor        6
 ...       243 -     249  are grouped by a factor        7
 ...       250 -     258  are grouped by a factor        9
 ...       259 -     266  are grouped by a factor        8
 ...       267 -     275  are grouped by a factor        9
 ...       276 -     282  are grouped by a factor        7
 ...       283 -     292  are grouped by a factor       10
 ...       293 -     303  are grouped by a factor       11
 ...       304 -     316  are grouped by a factor       13
 ...       317 -     326  are grouped by a factor       10
 ...       327 -     337  are grouped by a factor       11
 ...       338 -     350  are grouped by a factor       13
 ...       351 -     366  are grouped by a factor       16
 ...       367 -     391  are grouped by a factor       25
 ...       392 -     420  are grouped by a factor       29
 ...       421 -     441  are grouped by a factor       21
 ...       442 -     476  are grouped by a factor       35
 ...       477 -     530  are grouped by a factor       54
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_3.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis1c1p40_290296.fits already present in current directory
-> Generating ad63007000s110312_3.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110312_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   26 by   27 bins
               expanded to   26 by   27 bins
 First WMAP bin is at detector pixel  784  776
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   23.372     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  891.00  887.00 (detector coordinates)
 Point source at  -34.09  -14.15 (WMAP bins wrt optical axis)
 Point source at    7.83  202.54 (... in polar coordinates)
 
 Total counts in region = 3.03400E+03
 Weighted mean angle from optical axis  =  7.598 arcmin
-> Extracting ad63007000s110312_4.pi from ad63007000s132002_4.reg and:
ad63007000s100112h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813       557          42256         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813       557          42256         0         0         0
   in   50800.39 seconds
 Spectrum         has      557 counts for 1.0964E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.65039E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_4.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813       557          42256         0         0         0
 Writing events file
    557 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813       557          42256         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad63007000s110312_4.pi group=yes
Wrote spectrum to ad63007000s110312_4.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad63007000s110312_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 50800.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.65039E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      25  of undefined grouping (Channel quality=bad)
 ...        26 -      67  are grouped by a factor       42
 ...        68 -      75  are grouped by a factor        8
 ...        76 -      82  are grouped by a factor        7
 ...        83 -      91  are grouped by a factor        9
 ...        92 -     104  are grouped by a factor       13
 ...       105 -     112  are grouped by a factor        8
 ...       113 -     125  are grouped by a factor       13
 ...       126 -     136  are grouped by a factor       11
 ...       137 -     157  are grouped by a factor       21
 ...       158 -     188  are grouped by a factor       31
 ...       189 -     224  are grouped by a factor       36
 ...       225 -     282  are grouped by a factor       58
 ...       283 -     443  are grouped by a factor      161
 ...       444 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110312_4.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad63007000s110312_4.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C3 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad63007000s110312_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size    9 by    7 bins
               expanded to    9 by    7 bins
 First WMAP bin is at detector pixel  472  576
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   1.9018     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  511.00  607.00 (detector coordinates)
 Point source at   13.41   20.85 (WMAP bins wrt optical axis)
 Point source at    5.26   57.26 (... in polar coordinates)
 
 Total counts in region = 5.43000E+02
 Weighted mean angle from optical axis  =  5.312 arcmin
-> SIS1_NOTCHIP0.1 already present in current directory
-> SIS1_NOTCHIP3.1 already present in current directory
-> SIS1_OFFCHIP.1 already present in current directory
-> Extracting ad63007000s110412_1.pi from ad63007000s132002_1.reg and:
ad63007000s100412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835         0            835         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835         0            835         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT2 > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110412_1.pi not extracted

-> Extracting ad63007000s110412_2.pi from ad63007000s132002_2.reg and:
ad63007000s100412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835         0            835         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835         0            835         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT2 > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110412_2.pi not extracted

-> Extracting ad63007000s110412_3.pi from ad63007000s132002_3.reg and:
ad63007000s100412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835        55            780         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835        55            780         0         0         0
   in    1001.72 seconds
 Spectrum         has       55 counts for 5.4906E-02 counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 1001.7          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.02832E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      25  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000s110412_3.pi
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835        55            780         0         0         0
 Writing events file
     55 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835        55            780         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad63007000s110412_3.pi group=yes
Wrote spectrum to ad63007000s110412_3.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s110412_3.pi since it has 55 events
-> Extracting ad63007000s110412_4.pi from ad63007000s132002_4.reg and:
ad63007000s100412h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835         0            835         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835         0            835         0         0         0
   in    1001.72 seconds
 Spectrum         has        0 counts for     0.     counts/sec
extractor v2.0 : Failed to write the WMAP image
Failure for  extractor
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
Error in extractor
 XSL_BIN: Status =   256
xsel:ASCA-SIS1-BRIGHT2 > Session saved, goodbye

E2 in spectra: Spectrum ad63007000s110412_4.pi not extracted

-> Standard Output From STOOL group_event_files:
1 ad63007000g200170h.evt 97789
1 ad63007000g200270m.evt 97789
1 ad63007000g200370l.evt 97789
1 ad63007000g200470h.evt 97789
1 ad63007000g200670m.evt 97789
-> GIS2_REGION256.4 already present in current directory
-> Extracting ad63007000g210170_1.pi from ad63007000g225670_1.reg and:
ad63007000g200170h.evt
ad63007000g200270m.evt
ad63007000g200370l.evt
ad63007000g200470h.evt
ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     11996          45790         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      7927          30178         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        97            355         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       214            774         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       100            358         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789     20334          77455         0         0         0
   in   88108.63 seconds
 Spectrum         has    20334 counts for 0.2308     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad63007000g210170_1.pi group=yes
Wrote spectrum to ad63007000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad63007000g210170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g210170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 88109.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.18561E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -       5  are grouped by a factor        6
 ...         6 -     112  are single channels
 ...       113 -     114  are grouped by a factor        2
 ...       115 -     118  are single channels
 ...       119 -     138  are grouped by a factor        2
 ...       139 -     156  are grouped by a factor        3
 ...       157 -     164  are grouped by a factor        4
 ...       165 -     169  are grouped by a factor        5
 ...       170 -     172  are grouped by a factor        3
 ...       173 -     176  are grouped by a factor        4
 ...       177 -     181  are grouped by a factor        5
 ...       182 -     191  are grouped by a factor       10
 ...       192 -     202  are grouped by a factor       11
 ...       203 -     220  are grouped by a factor       18
 ...       221 -     240  are grouped by a factor       20
 ...       241 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g210170_1.pi
 ** grppha 2.6.0 completed successfully
-> Fetching gis2v4_0_256ch.rmf
-> Fetching s2bev1.fits
-> Fetching s2gridv3.fits
-> Generating ad63007000g210170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   31 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel   79   79
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   46.861     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 2.03340E+04
 Weighted mean angle from optical axis  =  8.112 arcmin
-> Extracting ad63007000g210170_2.pi from ad63007000g225670_2.reg and:
ad63007000g200170h.evt
ad63007000g200270m.evt
ad63007000g200370l.evt
ad63007000g200470h.evt
ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      6157          51629         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      4081          34024         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        59            393         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        91            897         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        43            415         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789     10431          87358         0         0         0
   in   88108.63 seconds
 Spectrum         has    10431 counts for 0.1184     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad63007000g210170_2.pi group=yes
Wrote spectrum to ad63007000g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad63007000g210170_2.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g210170_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 88109.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 7.58362E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -       6  are grouped by a factor        7
 ...         7 -       9  are grouped by a factor        3
 ...        10 -      13  are grouped by a factor        2
 ...        14 -      89  are single channels
 ...        90 -      91  are grouped by a factor        2
 ...        92 -      92  are single channels
 ...        93 -      96  are grouped by a factor        2
 ...        97 -      98  are single channels
 ...        99 -     122  are grouped by a factor        2
 ...       123 -     131  are grouped by a factor        3
 ...       132 -     139  are grouped by a factor        4
 ...       140 -     149  are grouped by a factor        5
 ...       150 -     155  are grouped by a factor        6
 ...       156 -     162  are grouped by a factor        7
 ...       163 -     172  are grouped by a factor       10
 ...       173 -     185  are grouped by a factor       13
 ...       186 -     202  are grouped by a factor       17
 ...       203 -     234  are grouped by a factor       32
 ...       235 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g210170_2.pi
 ** grppha 2.6.0 completed successfully
-> gis2v4_0_256ch.rmf already present in current directory
-> s2bev1.fits already present in current directory
-> s2gridv3.fits already present in current directory
-> Generating ad63007000g210170_2.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   25 by   25 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel  102   64
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   29.974     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  132.00   94.00 (detector coordinates)
 Point source at    1.00   36.96 (WMAP bins wrt optical axis)
 Point source at    9.08   88.45 (... in polar coordinates)
 
 Total counts in region = 1.04310E+04
 Weighted mean angle from optical axis  =  8.998 arcmin
-> Extracting ad63007000g210170_3.pi from ad63007000g225670_3.reg and:
ad63007000g200170h.evt
ad63007000g200270m.evt
ad63007000g200370l.evt
ad63007000g200470h.evt
ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      2705          55081         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      1842          36263         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        35            417         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        61            927         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        25            433         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789      4668          93121         0         0         0
   in   88108.63 seconds
 Spectrum         has     4668 counts for 5.2980E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad63007000g210170_3.pi group=yes
Wrote spectrum to ad63007000g210170_3.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad63007000g210170_3.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g210170_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 88109.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 5.44739E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      10  are grouped by a factor       11
 ...        11 -      14  are grouped by a factor        4
 ...        15 -      17  are grouped by a factor        3
 ...        18 -      19  are grouped by a factor        2
 ...        20 -      53  are single channels
 ...        54 -      55  are grouped by a factor        2
 ...        56 -      56  are single channels
 ...        57 -      60  are grouped by a factor        2
 ...        61 -      62  are single channels
 ...        63 -      66  are grouped by a factor        2
 ...        67 -      67  are single channels
 ...        68 -      95  are grouped by a factor        2
 ...        96 -      98  are grouped by a factor        3
 ...        99 -     102  are grouped by a factor        2
 ...       103 -     114  are grouped by a factor        3
 ...       115 -     118  are grouped by a factor        4
 ...       119 -     121  are grouped by a factor        3
 ...       122 -     129  are grouped by a factor        4
 ...       130 -     147  are grouped by a factor        6
 ...       148 -     167  are grouped by a factor       10
 ...       168 -     181  are grouped by a factor       14
 ...       182 -     216  are grouped by a factor       35
 ...       217 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g210170_3.pi
 ** grppha 2.6.0 completed successfully
-> gis2v4_0_256ch.rmf already present in current directory
-> s2bev1.fits already present in current directory
-> s2gridv3.fits already present in current directory
-> Generating ad63007000g210170_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   21 by   21 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel  122  123
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   21.531     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  152.00  153.00 (detector coordinates)
 Point source at  -19.00  -22.04 (WMAP bins wrt optical axis)
 Point source at    7.15  229.24 (... in polar coordinates)
 
 Total counts in region = 4.66800E+03
 Weighted mean angle from optical axis  =  7.227 arcmin
-> Extracting ad63007000g210170_4.pi from ad63007000g225670_4.reg and:
ad63007000g200170h.evt
ad63007000g200270m.evt
ad63007000g200370l.evt
ad63007000g200470h.evt
ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786       306          57480         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105       223          37882         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452         5            447         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988         8            980         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458         2            456         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789       544          97245         0         0         0
   in   88108.63 seconds
 Spectrum         has      544 counts for 6.1742E-03 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad63007000g210170_4.pi group=yes
Wrote spectrum to ad63007000g210170_4.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad63007000g210170_4.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g210170_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 88109.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.01416E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      13  are grouped by a factor       14
 ...        14 -      29  are grouped by a factor        8
 ...        30 -      34  are grouped by a factor        5
 ...        35 -      48  are grouped by a factor        7
 ...        49 -      58  are grouped by a factor       10
 ...        59 -      69  are grouped by a factor       11
 ...        70 -      82  are grouped by a factor       13
 ...        83 -     102  are grouped by a factor       20
 ...       103 -     124  are grouped by a factor       22
 ...       125 -     155  are grouped by a factor       31
 ...       156 -     231  are grouped by a factor       76
 ...       232 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g210170_4.pi
 ** grppha 2.6.0 completed successfully
-> gis2v4_0_256ch.rmf already present in current directory
-> s2bev1.fits already present in current directory
-> s2gridv3.fits already present in current directory
-> Generating ad63007000g210170_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   15 by   14 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel   44   32
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   7.9609     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at   74.00   62.50 (detector coordinates)
 Point source at   59.00   68.46 (WMAP bins wrt optical axis)
 Point source at   22.19   49.24 (... in polar coordinates)
 
 Total counts in region = 5.44000E+02
 Weighted mean angle from optical axis  = 22.219 arcmin
-> Standard Output From STOOL group_event_files:
1 ad63007000g300170h.evt 105146
1 ad63007000g300270m.evt 105146
1 ad63007000g300370l.evt 105146
1 ad63007000g300470h.evt 105146
1 ad63007000g300670m.evt 105146
-> GIS3_REGION256.4 already present in current directory
-> Extracting ad63007000g310170_1.pi from ad63007000g325670_1.reg and:
ad63007000g300170h.evt
ad63007000g300270m.evt
ad63007000g300370l.evt
ad63007000g300470h.evt
ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     14089          48309         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      9097          31487         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       109            409         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       274            856         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       110            406         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146     23679          81467         0         0         0
   in   89004.24 seconds
 Spectrum         has    23679 counts for 0.2660     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad63007000g310170_1.pi group=yes
Wrote spectrum to ad63007000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad63007000g310170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g310170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 89004.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 1.18561E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -       5  are grouped by a factor        6
 ...         6 -     115  are single channels
 ...       116 -     117  are grouped by a factor        2
 ...       118 -     119  are single channels
 ...       120 -     121  are grouped by a factor        2
 ...       122 -     125  are single channels
 ...       126 -     141  are grouped by a factor        2
 ...       142 -     144  are grouped by a factor        3
 ...       145 -     148  are grouped by a factor        2
 ...       149 -     151  are grouped by a factor        3
 ...       152 -     155  are grouped by a factor        4
 ...       156 -     161  are grouped by a factor        3
 ...       162 -     173  are grouped by a factor        4
 ...       174 -     178  are grouped by a factor        5
 ...       179 -     184  are grouped by a factor        6
 ...       185 -     193  are grouped by a factor        9
 ...       194 -     203  are grouped by a factor       10
 ...       204 -     229  are grouped by a factor       13
 ...       230 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g310170_1.pi
 ** grppha 2.6.0 completed successfully
-> Fetching gis3v4_0_256ch.rmf
-> Fetching s3bev1.fits
-> Fetching s3gridv3.fits
-> Generating ad63007000g310170_1.arf with point=no
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   31 by   31 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel   85   80
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   46.861     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Total counts in region = 2.36790E+04
 Weighted mean angle from optical axis  =  6.118 arcmin
-> Extracting ad63007000g310170_2.pi from ad63007000g325670_2.reg and:
ad63007000g300170h.evt
ad63007000g300270m.evt
ad63007000g300370l.evt
ad63007000g300470h.evt
ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      5746          56652         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      3731          36853         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        51            467         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       103           1027         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        43            473         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146      9674          95472         0         0         0
   in   89004.24 seconds
 Spectrum         has     9674 counts for 0.1087     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad63007000g310170_2.pi group=yes
Wrote spectrum to ad63007000g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad63007000g310170_2.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g310170_2.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 89004.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 7.58362E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -       7  are grouped by a factor        8
 ...         8 -      13  are grouped by a factor        2
 ...        14 -      80  are single channels
 ...        81 -      82  are grouped by a factor        2
 ...        83 -      88  are single channels
 ...        89 -      94  are grouped by a factor        2
 ...        95 -      95  are single channels
 ...        96 -      99  are grouped by a factor        2
 ...       100 -     100  are single channels
 ...       101 -     114  are grouped by a factor        2
 ...       115 -     117  are grouped by a factor        3
 ...       118 -     119  are grouped by a factor        2
 ...       120 -     125  are grouped by a factor        3
 ...       126 -     129  are grouped by a factor        4
 ...       130 -     132  are grouped by a factor        3
 ...       133 -     140  are grouped by a factor        4
 ...       141 -     146  are grouped by a factor        6
 ...       147 -     151  are grouped by a factor        5
 ...       152 -     160  are grouped by a factor        9
 ...       161 -     172  are grouped by a factor       12
 ...       173 -     186  are grouped by a factor       14
 ...       187 -     210  are grouped by a factor       24
 ...       211 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g310170_2.pi
 ** grppha 2.6.0 completed successfully
-> gis3v4_0_256ch.rmf already present in current directory
-> s3bev1.fits already present in current directory
-> s3gridv3.fits already present in current directory
-> Generating ad63007000g310170_2.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   25 by   25 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel  107   65
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   29.974     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  137.00   95.00 (detector coordinates)
 Point source at  -17.64   39.44 (WMAP bins wrt optical axis)
 Point source at   10.61  114.10 (... in polar coordinates)
 
 Total counts in region = 9.67400E+03
 Weighted mean angle from optical axis  = 10.452 arcmin
-> Extracting ad63007000g310170_3.pi from ad63007000g325670_3.reg and:
ad63007000g300170h.evt
ad63007000g300270m.evt
ad63007000g300370l.evt
ad63007000g300470h.evt
ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      2273          60125         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      1398          39186         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        10            508         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130        43           1087         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        23            493         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146      3747         101399         0         0         0
   in   89004.24 seconds
 Spectrum         has     3747 counts for 4.2099E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad63007000g310170_3.pi group=yes
Wrote spectrum to ad63007000g310170_3.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad63007000g310170_3.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g310170_3.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 89004.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 5.44739E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      11  are grouped by a factor       12
 ...        12 -      16  are grouped by a factor        5
 ...        17 -      19  are grouped by a factor        3
 ...        20 -      23  are grouped by a factor        2
 ...        24 -      50  are single channels
 ...        51 -      76  are grouped by a factor        2
 ...        77 -      79  are grouped by a factor        3
 ...        80 -      87  are grouped by a factor        2
 ...        88 -      90  are grouped by a factor        3
 ...        91 -      92  are grouped by a factor        2
 ...        93 -     110  are grouped by a factor        3
 ...       111 -     122  are grouped by a factor        4
 ...       123 -     127  are grouped by a factor        5
 ...       128 -     133  are grouped by a factor        6
 ...       134 -     141  are grouped by a factor        8
 ...       142 -     153  are grouped by a factor       12
 ...       154 -     167  are grouped by a factor       14
 ...       168 -     187  are grouped by a factor       20
 ...       188 -     240  are grouped by a factor       53
 ...       241 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g310170_3.pi
 ** grppha 2.6.0 completed successfully
-> gis3v4_0_256ch.rmf already present in current directory
-> s3bev1.fits already present in current directory
-> s3gridv3.fits already present in current directory
-> Generating ad63007000g310170_3.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   21 by   21 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel  127  123
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   21.531     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  157.00  153.00 (detector coordinates)
 Point source at  -37.64  -18.56 (WMAP bins wrt optical axis)
 Point source at   10.31  206.25 (... in polar coordinates)
 
 Total counts in region = 3.74700E+03
 Weighted mean angle from optical axis  = 10.213 arcmin
-> Extracting ad63007000g310170_4.pi from ad63007000g325670_4.reg and:
ad63007000g300170h.evt
ad63007000g300270m.evt
ad63007000g300370l.evt
ad63007000g300470h.evt
ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398       503          61895         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584       350          40234         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518         5            513         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130         6           1124         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516         6            510         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146       870         104276         0         0         0
   in   89004.24 seconds
 Spectrum         has      870 counts for 9.7748E-03 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad63007000g310170_4.pi group=yes
Wrote spectrum to ad63007000g310170_4.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad63007000g310170_4.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad63007000g310170_4.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 89004.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.19727E-03     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 256             No. of legal detector channels
  NCHAN     - 256             No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      18  are grouped by a factor       19
 ...        19 -      24  are grouped by a factor        6
 ...        25 -      40  are grouped by a factor        4
 ...        41 -      43  are grouped by a factor        3
 ...        44 -      51  are grouped by a factor        4
 ...        52 -      69  are grouped by a factor        6
 ...        70 -      76  are grouped by a factor        7
 ...        77 -      82  are grouped by a factor        6
 ...        83 -      91  are grouped by a factor        9
 ...        92 -     105  are grouped by a factor       14
 ...       106 -     114  are grouped by a factor        9
 ...       115 -     132  are grouped by a factor       18
 ...       133 -     162  are grouped by a factor       30
 ...       163 -     218  are grouped by a factor       56
 ...       219 -     255  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad63007000g310170_4.pi
 ** grppha 2.6.0 completed successfully
-> gis3v4_0_256ch.rmf already present in current directory
-> s3bev1.fits already present in current directory
-> s3gridv3.fits already present in current directory
-> Generating ad63007000g310170_4.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   15 by   14 bins
               expanded to   64 by   64 bins
 First WMAP bin is at detector pixel   48   30
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   8.6846     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
 Making correction for no RTI
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at   78.00   60.50 (detector coordinates)
 Point source at   41.36   73.94 (WMAP bins wrt optical axis)
 Point source at   20.80   60.78 (... in polar coordinates)
 
 Total counts in region = 8.70000E+02
 Weighted mean angle from optical axis  = 20.869 arcmin
-> Plotting ad63007000g210170_1_pi.ps from ad63007000g210170_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:08:39 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g210170_1.pi
 Net count rate (cts/s) for file   1  0.2308    +/-  1.6189E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g210170_2_pi.ps from ad63007000g210170_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:09:09 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g210170_2.pi
 Net count rate (cts/s) for file   1  0.1184    +/-  1.1600E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g210170_3_pi.ps from ad63007000g210170_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:09:36 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g210170_3.pi
 Net count rate (cts/s) for file   1  5.2980E-02+/-  7.7726E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g210170_4_pi.ps from ad63007000g210170_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:10:03 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g210170_4.pi
 Net count rate (cts/s) for file   1  6.1742E-03+/-  2.6978E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g310170_1_pi.ps from ad63007000g310170_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:10:30 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g310170_1.pi
 Net count rate (cts/s) for file   1  0.2660    +/-  1.7293E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g310170_2_pi.ps from ad63007000g310170_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:10:57 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g310170_2.pi
 Net count rate (cts/s) for file   1  0.1087    +/-  1.1063E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g310170_3_pi.ps from ad63007000g310170_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:11:25 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g310170_3.pi
 Net count rate (cts/s) for file   1  4.2099E-02+/-  6.8894E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000g310170_4_pi.ps from ad63007000g310170_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:11:54 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000g310170_4.pi
 Net count rate (cts/s) for file   1  9.7748E-03+/-  3.3518E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010102_1_pi.ps from ad63007000s010102_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:12:21 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010102_1.pi
 Net count rate (cts/s) for file   1  0.1452    +/-  1.3847E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010102_2_pi.ps from ad63007000s010102_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:12:53 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010102_2.pi
 Net count rate (cts/s) for file   1  0.2640    +/-  1.8707E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010102_3_pi.ps from ad63007000s010102_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:13:25 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010102_3.pi
 Net count rate (cts/s) for file   1  4.9554E-02+/-  8.2706E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010102_4_pi.ps from ad63007000s010102_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:13:58 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010102_4.pi
 Net count rate (cts/s) for file   1  1.3199E-02+/-  4.5849E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010202_2_pi.ps from ad63007000s010202_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:14:32 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010202_2.pi
 Net count rate (cts/s) for file   1  0.2559    +/-  1.3113E-02
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010412_1_pi.ps from ad63007000s010412_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:15:05 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010412_1.pi
 Net count rate (cts/s) for file   1  0.1634    +/-  1.8631E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010412_2_pi.ps from ad63007000s010412_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:15:41 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010412_2.pi
 Net count rate (cts/s) for file   1  0.2959    +/-  2.5289E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010412_3_pi.ps from ad63007000s010412_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:16:17 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010412_3.pi
 Net count rate (cts/s) for file   1  5.6732E-02+/-  1.1488E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010412_4_pi.ps from ad63007000s010412_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:16:55 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010412_4.pi
 Net count rate (cts/s) for file   1  1.3998E-02+/-  7.7055E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s010512_2_pi.ps from ad63007000s010512_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:17:32 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s010512_2.pi
 Net count rate (cts/s) for file   1  0.2794    +/-  1.5434E-02
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110102_1_pi.ps from ad63007000s110102_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:18:12 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110102_1.pi
 Net count rate (cts/s) for file   1  8.2325E-02+/-  1.0136E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110102_2_pi.ps from ad63007000s110102_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:18:44 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110102_2.pi
 Net count rate (cts/s) for file   1  0.1726    +/-  1.4598E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110102_3_pi.ps from ad63007000s110102_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:19:18 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110102_3.pi
 Net count rate (cts/s) for file   1  4.9442E-02+/-  7.9003E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110102_4_pi.ps from ad63007000s110102_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:19:50 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110102_4.pi
 Net count rate (cts/s) for file   1  9.3515E-03+/-  3.6830E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110312_1_pi.ps from ad63007000s110312_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:20:24 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110312_1.pi
 Net count rate (cts/s) for file   1  0.1027    +/-  1.4439E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110312_2_pi.ps from ad63007000s110312_2.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:20:58 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110312_2.pi
 Net count rate (cts/s) for file   1  0.2096    +/-  2.0338E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110312_3_pi.ps from ad63007000s110312_3.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:21:37 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110312_3.pi
 Net count rate (cts/s) for file   1  6.0275E-02+/-  1.0939E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad63007000s110312_4_pi.ps from ad63007000s110312_4.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 14:22:16 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad63007000s110312_4.pi
 Net count rate (cts/s) for file   1  1.0964E-02+/-  6.6900E-04
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit

Extracting light curves ( 14:22:43 )

-> TIMEDEL=1.6000000000E+01 for ad63007000s000102h.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s000202m.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s000302h.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s000402h.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s000502l.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s000602m.evt
-> Minimum bin size is 1.6000000000E+01 seconds
-> Extracting events from region ad63007000s032002_1.reg
-> ... and files: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
      6 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      6940          38085         0         0         0
 Writing events file
   6940 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      4225          22035         0         0         0
 Writing events file
  11165 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        70            820         0         0         0
 Writing events file
  11235 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       365           1749         0         0         0
 Writing events file
  11600 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
  11600 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        53            367         0         0         0
 Writing events file
  11653 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         74797     11653          63144         0         0         0
   in   80596.11 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000302h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad63007000s000002_1.lc with binsize 345.816998667922
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.81E+05    11653 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          11653     11653              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11653     11653              0         0         0         0
   in   80596.11 seconds
 Fits light curve has    11653 counts for 0.1446     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 345.816998667922
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad63007000s000002_1.lc
Wrote FITS light curve to file ad63007000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s000002_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s000002_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......          242        Bin Time (s) ......    345.8
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS0
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.1457        Chisq  358.7       Var 0.8039E-03 Newbs.   217
               Min 0.2753E-01      Max 0.2402    expVar 0.4596E-03  Bins    242

             Results from Statistical Analysis

             Newbin Integration Time (s)..  398.15    
             Interval Duration (s)........ 0.20346E+06
             No. of Newbins ..............     217
             Average (c/s) ............... 0.14566      +/-    0.15E-02
             Standard Deviation (c/s)..... 0.28353E-01
             Minimum (c/s)................ 0.27532E-01
             Maximum (c/s)................ 0.24018    
             Variance ((c/s)**2).......... 0.80389E-03 +/-    0.77E-04
             Expected Variance ((c/s)**2). 0.45963E-03 +/-    0.44E-04
             Third Moment ((c/s)**3)......-0.94098E-05
             Average Deviation (c/s)...... 0.20699E-01
             Skewness.....................-0.41284        +/-    0.17    
             Kurtosis.....................  2.3455        +/-    0.33    
             RMS fractional variation..... 0.12739        +/-    0.14E-01
             Chi-Square...................  358.65        dof     216
             Chi-Square Prob of constancy. 0.36054E-08 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.27386E-06 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.1457        Chisq  358.7       Var 0.8039E-03 Newbs.   217
               Min 0.2753E-01      Max 0.2402    expVar 0.4596E-03  Bins    242
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s032002_2.reg
-> ... and files: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
      6 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     12690          32335         0         0         0
 Writing events file
  12690 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      7322          18938         0         0         0
 Writing events file
  20012 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       219            671         0         0         0
 Writing events file
  20231 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       589           1525         0         0         0
 Writing events file
  20820 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         6             82         0         0         0
 Writing events file
  20826 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       108            312         0         0         0
 Writing events file
  20934 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         74797     20934          53863         0         0         0
   in   80596.11 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000302h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad63007000s000002_2.lc with binsize 192.500500882645
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.81E+05    20934 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          20934     20934              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20934     20934              0         0         0         0
   in   80596.11 seconds
 Fits light curve has    20934 counts for 0.2597     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 192.500500882645
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad63007000s000002_2.lc
Wrote FITS light curve to file ad63007000s000002_2.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s000002_2_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s000002_2.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......          431        Bin Time (s) ......    192.5
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS0
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.2623        Chisq  320.6       Var 0.1389E-02 Newbs.   241
               Min 0.1266          Max 0.3828    expVar 0.9622E-03  Bins    431

             Results from Statistical Analysis

             Newbin Integration Time (s)..  398.15    
             Interval Duration (s)........ 0.20306E+06
             No. of Newbins ..............     241
             Average (c/s) ............... 0.26230      +/-    0.20E-02
             Standard Deviation (c/s)..... 0.37269E-01
             Minimum (c/s)................ 0.12664    
             Maximum (c/s)................ 0.38281    
             Variance ((c/s)**2).......... 0.13889E-02 +/-    0.13E-03
             Expected Variance ((c/s)**2). 0.96222E-03 +/-    0.88E-04
             Third Moment ((c/s)**3)......-0.46355E-05
             Average Deviation (c/s)...... 0.29118E-01
             Skewness.....................-0.89550E-01    +/-    0.16    
             Kurtosis..................... 0.94347        +/-    0.32    
             RMS fractional variation..... 0.78755E-01    +/-    0.12E-01
             Chi-Square...................  320.65        dof     240
             Chi-Square Prob of constancy. 0.38385E-03 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.42056E-06 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.2623        Chisq  320.6       Var 0.1389E-02 Newbs.   241
               Min 0.1266          Max 0.3828    expVar 0.9622E-03  Bins    431
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s032002_3.reg
-> ... and files: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
      6 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      2336          42689         0         0         0
 Writing events file
   2336 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      1421          24839         0         0         0
 Writing events file
   3757 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        57            833         0         0         0
 Writing events file
   3814 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       112           2002         0         0         0
 Writing events file
   3926 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         1             87         0         0         0
 Writing events file
   3927 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        26            394         0         0         0
 Writing events file
   3953 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         74797      3953          70844         0         0         0
   in   80596.11 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000302h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad63007000s000002_3.lc with binsize 1019.42966999173
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.81E+05     3953 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           3953      3953              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3953      3953              0         0         0         0
   in   80596.11 seconds
 Fits light curve has     3953 counts for 4.9047E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 1019.42966999173
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad63007000s000002_3.lc
Wrote FITS light curve to file ad63007000s000002_3.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s000002_3_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s000002_3.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......           82        Bin Time (s) ......    1019.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS0
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       200 Newbins of       1019.43     (s) 

 
 Intv    1   Start 9927 23:34:44
     Ser.1     Avg 0.4973E-01    Chisq  89.62       Var 0.6934E-04 Newbs.    82
               Min 0.3062E-01      Max 0.7275E-01expVar 0.6344E-04  Bins     82

             Results from Statistical Analysis

             Newbin Integration Time (s)..  1019.4    
             Interval Duration (s)........ 0.20287E+06
             No. of Newbins ..............      82
             Average (c/s) ............... 0.49727E-01  +/-    0.89E-03
             Standard Deviation (c/s)..... 0.83268E-02
             Minimum (c/s)................ 0.30617E-01
             Maximum (c/s)................ 0.72754E-01
             Variance ((c/s)**2).......... 0.69336E-04 +/-    0.11E-04
             Expected Variance ((c/s)**2). 0.63443E-04 +/-    0.10E-04
             Third Moment ((c/s)**3)...... 0.34035E-07
             Average Deviation (c/s)...... 0.66728E-02
             Skewness..................... 0.58952E-01    +/-    0.27    
             Kurtosis.....................-0.11734        +/-    0.54    
             RMS fractional variation....< 0.10689     (3 sigma)
             Chi-Square...................  89.617        dof      81
             Chi-Square Prob of constancy. 0.24001     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.66810E-01 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       200 Newbins of       1019.43     (s) 

 
 Intv    1   Start 9927 23:34:44
     Ser.1     Avg 0.4973E-01    Chisq  89.62       Var 0.6934E-04 Newbs.    82
               Min 0.3062E-01      Max 0.7275E-01expVar 0.6344E-04  Bins     82
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s032002_4.reg
-> ... and files: ad63007000s000102h.evt ad63007000s000202m.evt ad63007000s000302h.evt ad63007000s000402h.evt ad63007000s000502l.evt ad63007000s000602m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
      3 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
      4 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
      5 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
      6 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025       615          44410         0         0         0
 Writing events file
    615 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260       386          25874         0         0         0
 Writing events file
   1001 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        19            871         0         0         0
 Writing events file
   1020 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114        33           2081         0         0         0
 Writing events file
   1053 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
   1053 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420         5            415         0         0         0
 Writing events file
   1058 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         74797      1058          73739         0         0         0
   in   80596.11 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000302h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000502l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad63007000s000602m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad63007000s000002_4.lc with binsize 3808.88987285189
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.81E+05     1058 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           1058      1058              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1058      1058              0         0         0         0
   in   80596.11 seconds
 Fits light curve has     1058 counts for 1.3127E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 3808.88987285189
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad63007000s000002_4.lc
Wrote FITS light curve to file ad63007000s000002_4.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s000002_4_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s000002_4.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......           13        Bin Time (s) ......    3809.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS0
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        54 Newbins of       3808.89     (s) 

 
 Intv    1   Start 9927 23:57:58
     Ser.1     Avg 0.1205E-01    Chisq  17.23       Var 0.6832E-05 Newbs.    13
               Min 0.8241E-02      Max 0.1737E-01expVar 0.5156E-05  Bins     13

             Results from Statistical Analysis

             Newbin Integration Time (s)..  3808.9    
             Interval Duration (s)........ 0.18283E+06
             No. of Newbins ..............      13
             Average (c/s) ............... 0.12054E-01  +/-    0.66E-03
             Standard Deviation (c/s)..... 0.26138E-02
             Minimum (c/s)................ 0.82415E-02
             Maximum (c/s)................ 0.17371E-01
             Variance ((c/s)**2).......... 0.68321E-05 +/-    0.28E-05
             Expected Variance ((c/s)**2). 0.51561E-05 +/-    0.21E-05
             Third Moment ((c/s)**3)...... 0.71681E-08
             Average Deviation (c/s)...... 0.23962E-02
             Skewness..................... 0.40139        +/-    0.68    
             Kurtosis.....................-0.96042        +/-     1.4    
             RMS fractional variation....< 0.21869     (3 sigma)
             Chi-Square...................  17.226        dof      12
             Chi-Square Prob of constancy. 0.14132     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.15053E-02 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        54 Newbins of       3808.89     (s) 

 
 Intv    1   Start 9927 23:57:58
     Ser.1     Avg 0.1205E-01    Chisq  17.23       Var 0.6832E-05 Newbs.    13
               Min 0.8241E-02      Max 0.1737E-01expVar 0.5156E-05  Bins     13
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> TIMEDEL=1.6000000000E+01 for ad63007000s100102h.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s100202m.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s100302l.evt
-> TIMEDEL=1.6000000000E+01 for ad63007000s100402h.evt
-> Minimum bin size is 1.6000000000E+01 seconds
-> Extracting events from region ad63007000s132002_1.reg
-> ... and files: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
      4 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      4203          31394         0         0         0
 Writing events file
   4203 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      2514          17941         0         0         0
 Writing events file
   6717 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         3             98         0         0         0
 Writing events file
   6720 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        97            605         0         0         0
 Writing events file
   6817 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56855      6817          50038         0         0         0
   in   82593.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad63007000s100002_1.lc with binsize 605.786967824653
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.83E+05     6817 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           6817      6817              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          6817      6817              0         0         0         0
   in   82593.00 seconds
 Fits light curve has     6817 counts for 8.2537E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 605.786967824653
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad63007000s100002_1.lc
Wrote FITS light curve to file ad63007000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s100002_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s100002_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......          141        Bin Time (s) ......    605.8
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS1
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       337 Newbins of       605.787     (s) 

 
 Intv    1   Start 9927 23:31:17
     Ser.1     Avg 0.8237E-01    Chisq  151.3       Var 0.1735E-03 Newbs.   141
               Min 0.4316E-01      Max 0.1242    expVar 0.1617E-03  Bins    141

             Results from Statistical Analysis

             Newbin Integration Time (s)..  605.79    
             Interval Duration (s)........ 0.20294E+06
             No. of Newbins ..............     141
             Average (c/s) ............... 0.82366E-01  +/-    0.11E-02
             Standard Deviation (c/s)..... 0.13172E-01
             Minimum (c/s)................ 0.43155E-01
             Maximum (c/s)................ 0.12419    
             Variance ((c/s)**2).......... 0.17351E-03 +/-    0.21E-04
             Expected Variance ((c/s)**2). 0.16166E-03 +/-    0.19E-04
             Third Moment ((c/s)**3)...... 0.13353E-07
             Average Deviation (c/s)...... 0.10471E-01
             Skewness..................... 0.58426E-02    +/-    0.21    
             Kurtosis..................... 0.55184        +/-    0.41    
             RMS fractional variation....< 0.87821E-01 (3 sigma)
             Chi-Square...................  151.33        dof     140
             Chi-Square Prob of constancy. 0.24219     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.12800     (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       337 Newbins of       605.787     (s) 

 
 Intv    1   Start 9927 23:31:17
     Ser.1     Avg 0.8237E-01    Chisq  151.3       Var 0.1735E-03 Newbs.   141
               Min 0.4316E-01      Max 0.1242    expVar 0.1617E-03  Bins    141
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s132002_2.reg
-> ... and files: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
      4 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      9050          26547         0         0         0
 Writing events file
   9050 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      5027          15428         0         0         0
 Writing events file
  14077 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
  14084 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702       168            534         0         0         0
 Writing events file
  14252 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56855     14252          42603         0         0         0
   in   82593.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad63007000s100002_2.lc with binsize 289.759315160024
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.83E+05    14252 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          14252     14252              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         14252     14252              0         0         0         0
   in   82593.00 seconds
 Fits light curve has    14252 counts for 0.1726     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 289.759315160024
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad63007000s100002_2.lc
Wrote FITS light curve to file ad63007000s100002_2.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s100002_2_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s100002_2.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......          299        Bin Time (s) ......    289.8
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS1
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.1735        Chisq  280.0       Var 0.7581E-03 Newbs.   232
               Min 0.1104          Max 0.2862    expVar 0.5926E-03  Bins    299

             Results from Statistical Analysis

             Newbin Integration Time (s)..  398.15    
             Interval Duration (s)........ 0.20346E+06
             No. of Newbins ..............     232
             Average (c/s) ............... 0.17352      +/-    0.16E-02
             Standard Deviation (c/s)..... 0.27534E-01
             Minimum (c/s)................ 0.11044    
             Maximum (c/s)................ 0.28623    
             Variance ((c/s)**2).......... 0.75813E-03 +/-    0.71E-04
             Expected Variance ((c/s)**2). 0.59262E-03 +/-    0.55E-04
             Third Moment ((c/s)**3)...... 0.11764E-04
             Average Deviation (c/s)...... 0.21973E-01
             Skewness..................... 0.56358        +/-    0.16    
             Kurtosis..................... 0.99858        +/-    0.32    
             RMS fractional variation....< 0.21461E-01 (3 sigma)
             Chi-Square...................  280.04        dof     231
             Chi-Square Prob of constancy. 0.15071E-01 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.40219E-01 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       398.154     (s) 

 
 Intv    1   Start 9927 23:29:33
     Ser.1     Avg 0.1735        Chisq  280.0       Var 0.7581E-03 Newbs.   232
               Min 0.1104          Max 0.2862    expVar 0.5926E-03  Bins    299
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s132002_3.reg
-> ... and files: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
      4 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      2579          33018         0         0         0
 Writing events file
   2579 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      1448          19007         0         0         0
 Writing events file
   4027 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
   4034 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        43            659         0         0         0
 Writing events file
   4077 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56855      4077          52778         0         0         0
   in   82593.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad63007000s100002_3.lc with binsize 1012.91384833472
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.83E+05     4077 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           4077      4077              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4077      4077              0         0         0         0
   in   82593.00 seconds
 Fits light curve has     4077 counts for 4.9363E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 1012.91384833472
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad63007000s100002_3.lc
Wrote FITS light curve to file ad63007000s100002_3.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s100002_3_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s100002_3.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......           82        Bin Time (s) ......    1013.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS1
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       202 Newbins of       1012.91     (s) 

 
 Intv    1   Start 9927 23:34:41
     Ser.1     Avg 0.4943E-01    Chisq  91.23       Var 0.6844E-04 Newbs.    82
               Min 0.3020E-01      Max 0.6901E-01expVar 0.6151E-04  Bins     82

             Results from Statistical Analysis

             Newbin Integration Time (s)..  1012.9    
             Interval Duration (s)........ 0.20258E+06
             No. of Newbins ..............      82
             Average (c/s) ............... 0.49434E-01  +/-    0.87E-03
             Standard Deviation (c/s)..... 0.82727E-02
             Minimum (c/s)................ 0.30195E-01
             Maximum (c/s)................ 0.69009E-01
             Variance ((c/s)**2).......... 0.68437E-04 +/-    0.11E-04
             Expected Variance ((c/s)**2). 0.61513E-04 +/-    0.97E-05
             Third Moment ((c/s)**3)...... 0.18246E-07
             Average Deviation (c/s)...... 0.64789E-02
             Skewness..................... 0.32227E-01    +/-    0.27    
             Kurtosis.....................-0.78929E-01    +/-    0.54    
             RMS fractional variation....< 0.10351     (3 sigma)
             Chi-Square...................  91.230        dof      81
             Chi-Square Prob of constancy. 0.20497     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.30097E-01 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       202 Newbins of       1012.91     (s) 

 
 Intv    1   Start 9927 23:34:41
     Ser.1     Avg 0.4943E-01    Chisq  91.23       Var 0.6844E-04 Newbs.    82
               Min 0.3020E-01      Max 0.6901E-01expVar 0.6151E-04  Bins     82
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000s132002_4.reg
-> ... and files: ad63007000s100102h.evt ad63007000s100202m.evt ad63007000s100302l.evt ad63007000s100402h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
      2 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
      3 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
      4 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597       488          35109         0         0         0
 Writing events file
    488 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455       291          20164         0         0         0
 Writing events file
    779 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         0            101         0         0         0
 Writing events file
    779 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        16            686         0         0         0
 Writing events file
    795 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         56855       795          56060         0         0         0
   in   82593.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100202m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100302l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad63007000s100402h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad63007000s100002_4.lc with binsize 5194.52799957316
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     29/07/95 22:35:02 0.83E+05      795 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            795       795              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           795       795              0         0         0         0
   in   82593.00 seconds
 Fits light curve has      795 counts for 9.6255E-03 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 5194.52799957316
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad63007000s100002_4.lc
Wrote FITS light curve to file ad63007000s100002_4.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad63007000s100002_4_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000s100002_4.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 23:26:14.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 07:59:50.549
 No. of Rows .......            4        Bin Time (s) ......    5195.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     SIS1
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        40 Newbins of       5194.53     (s) 

 
 Intv    1   Start 9928  5:55:49
     Ser.1     Avg 0.8301E-02    Chisq 0.7739       Var 0.5557E-06 Newbs.     4
               Min 0.7200E-02      Max 0.9247E-02expVar 0.2872E-05  Bins      4

             Results from Statistical Analysis

             Newbin Integration Time (s)..  5194.5    
             Interval Duration (s)........  51945.    
             No. of Newbins ..............       4
             Average (c/s) ............... 0.83010E-02  +/-    0.98E-03
             Standard Deviation (c/s)..... 0.74548E-03
             Minimum (c/s)................ 0.71995E-02
             Maximum (c/s)................ 0.92470E-02
             Variance ((c/s)**2).......... 0.55575E-06 +/-    0.45E-06
             Expected Variance ((c/s)**2). 0.28724E-05 +/-    0.23E-05
             Third Moment ((c/s)**3)......-0.11629E-09
             Average Deviation (c/s)...... 0.62519E-03
             Skewness.....................-0.28069        +/-     1.2    
             Kurtosis..................... -1.1529        +/-     2.4    
             RMS fractional variation....< 0.45707     (3 sigma)
             Chi-Square................... 0.77390        dof       3
             Chi-Square Prob of constancy. 0.85569     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.41506     (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        40 Newbins of       5194.53     (s) 

 
 Intv    1   Start 9928  5:55:49
     Ser.1     Avg 0.8301E-02    Chisq 0.7739       Var 0.5557E-06 Newbs.     4
               Min 0.7200E-02      Max 0.9247E-02expVar 0.2872E-05  Bins      4
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> TIMEDEL=4.8828125000E-04 for ad63007000g200170h.evt
-> TIMEDEL=3.9062500000E-03 for ad63007000g200270m.evt
-> TIMEDEL=1.5625000000E-02 for ad63007000g200370l.evt
-> TIMEDEL=4.8828125000E-04 for ad63007000g200470h.evt
-> TIMEDEL=3.9062500000E-03 for ad63007000g200670m.evt
-> Minimum bin size is 1.5625000000E-02 seconds
-> Extracting events from region ad63007000g225670_1.reg
-> ... and files: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     11996          45790         0         0         0
 Writing events file
  11996 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      7927          30178         0         0         0
 Writing events file
  19923 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        97            355         0         0         0
 Writing events file
  20020 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       214            774         0         0         0
 Writing events file
  20234 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       100            358         0         0         0
 Writing events file
  20334 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789     20334          77455         0         0         0
   in   88108.63 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200070_1.lc with binsize 216.653463237183
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.88E+05    20334      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          20334     20334              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20334     20334              0         0         0         0
   in   88108.63 seconds
 Fits light curve has    20334 counts for 0.2308     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set binsize 216.653463237183
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad63007000g200070_1.lc
Wrote FITS light curve to file ad63007000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad63007000g200070_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g200070_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......          408        Bin Time (s) ......    216.7
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS2
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       404.192     (s) 

 
 Intv    1   Start 9927 23:29:13
     Ser.1     Avg 0.2309        Chisq  241.8       Var 0.9562E-03 Newbs.   244
               Min 0.1554          Max 0.3375    expVar 0.7867E-03  Bins    408

             Results from Statistical Analysis

             Newbin Integration Time (s)..  404.19    
             Interval Duration (s)........ 0.20331E+06
             No. of Newbins ..............     244
             Average (c/s) ............... 0.23088      +/-    0.18E-02
             Standard Deviation (c/s)..... 0.30923E-01
             Minimum (c/s)................ 0.15537    
             Maximum (c/s)................ 0.33749    
             Variance ((c/s)**2).......... 0.95622E-03 +/-    0.87E-04
             Expected Variance ((c/s)**2). 0.78669E-03 +/-    0.71E-04
             Third Moment ((c/s)**3)...... 0.83921E-05
             Average Deviation (c/s)...... 0.23991E-01
             Skewness..................... 0.28382        +/-    0.16    
             Kurtosis..................... 0.43861        +/-    0.31    
             RMS fractional variation....< 0.34082E-01 (3 sigma)
             Chi-Square...................  241.76        dof     243
             Chi-Square Prob of constancy. 0.51032     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.75201E-02 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       404.192     (s) 

 
 Intv    1   Start 9927 23:29:13
     Ser.1     Avg 0.2309        Chisq  241.8       Var 0.9562E-03 Newbs.   244
               Min 0.1554          Max 0.3375    expVar 0.7867E-03  Bins    408
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g225670_2.reg
-> ... and files: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      6157          51629         0         0         0
 Writing events file
   6157 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      4081          34024         0         0         0
 Writing events file
  10238 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        59            393         0         0         0
 Writing events file
  10297 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        91            897         0         0         0
 Writing events file
  10388 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        43            415         0         0         0
 Writing events file
  10431 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789     10431          87358         0         0         0
   in   88108.63 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200070_2.lc with binsize 422.34028582733
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.88E+05    10431      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          10431     10431              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10431     10431              0         0         0         0
   in   88108.63 seconds
 Fits light curve has    10431 counts for 0.1184     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set binsize 422.34028582733
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad63007000g200070_2.lc
Wrote FITS light curve to file ad63007000g200070_2.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad63007000g200070_2_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g200070_2.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......          212        Bin Time (s) ......    422.3
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS2
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       490 Newbins of       422.340     (s) 

 
 Intv    1   Start 9927 23:28: 6
     Ser.1     Avg 0.1189        Chisq  217.5       Var 0.3253E-03 Newbs.   212
               Min 0.6604E-01      Max 0.1693    expVar 0.3170E-03  Bins    212

             Results from Statistical Analysis

             Newbin Integration Time (s)..  422.34    
             Interval Duration (s)........ 0.20315E+06
             No. of Newbins ..............     212
             Average (c/s) ............... 0.11887      +/-    0.12E-02
             Standard Deviation (c/s)..... 0.18035E-01
             Minimum (c/s)................ 0.66037E-01
             Maximum (c/s)................ 0.16935    
             Variance ((c/s)**2).......... 0.32527E-03 +/-    0.32E-04
             Expected Variance ((c/s)**2). 0.31704E-03 +/-    0.31E-04
             Third Moment ((c/s)**3)...... 0.13492E-05
             Average Deviation (c/s)...... 0.14442E-01
             Skewness..................... 0.22999        +/-    0.17    
             Kurtosis.....................-0.45503E-01    +/-    0.34    
             RMS fractional variation....< 0.80858E-01 (3 sigma)
             Chi-Square...................  217.51        dof     211
             Chi-Square Prob of constancy. 0.36472     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.99144E-04 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       490 Newbins of       422.340     (s) 

 
 Intv    1   Start 9927 23:28: 6
     Ser.1     Avg 0.1189        Chisq  217.5       Var 0.3253E-03 Newbs.   212
               Min 0.6604E-01      Max 0.1693    expVar 0.3170E-03  Bins    212
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g225670_3.reg
-> ... and files: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      2705          55081         0         0         0
 Writing events file
   2705 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      1842          36263         0         0         0
 Writing events file
   4547 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        35            417         0         0         0
 Writing events file
   4582 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        61            927         0         0         0
 Writing events file
   4643 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        25            433         0         0         0
 Writing events file
   4668 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789      4668          93121         0         0         0
   in   88108.63 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200070_3.lc with binsize 943.751397057602
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.88E+05     4668      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           4668      4668              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4668      4668              0         0         0         0
   in   88108.63 seconds
 Fits light curve has     4668 counts for 5.2980E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set binsize 943.751397057602
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad63007000g200070_3.lc
Wrote FITS light curve to file ad63007000g200070_3.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad63007000g200070_3_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g200070_3.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......           95        Bin Time (s) ......    943.8
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS2
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       220 Newbins of       943.751     (s) 

 
 Intv    1   Start 9927 23:30:21
     Ser.1     Avg 0.5246E-01    Chisq  113.3       Var 0.8426E-04 Newbs.    95
               Min 0.3497E-01      Max 0.8001E-01expVar 0.7064E-04  Bins     95

             Results from Statistical Analysis

             Newbin Integration Time (s)..  943.75    
             Interval Duration (s)........ 0.20291E+06
             No. of Newbins ..............      95
             Average (c/s) ............... 0.52461E-01  +/-    0.87E-03
             Standard Deviation (c/s)..... 0.91792E-02
             Minimum (c/s)................ 0.34967E-01
             Maximum (c/s)................ 0.80007E-01
             Variance ((c/s)**2).......... 0.84258E-04 +/-    0.12E-04
             Expected Variance ((c/s)**2). 0.70642E-04 +/-    0.10E-04
             Third Moment ((c/s)**3)...... 0.33476E-06
             Average Deviation (c/s)...... 0.74727E-02
             Skewness..................... 0.43283        +/-    0.25    
             Kurtosis.....................-0.19565        +/-    0.50    
             RMS fractional variation....< 0.88098E-01 (3 sigma)
             Chi-Square...................  113.31        dof      94
             Chi-Square Prob of constancy. 0.85363E-01 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.10231     (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       220 Newbins of       943.751     (s) 

 
 Intv    1   Start 9927 23:30:21
     Ser.1     Avg 0.5246E-01    Chisq  113.3       Var 0.8426E-04 Newbs.    95
               Min 0.3497E-01      Max 0.8001E-01expVar 0.7064E-04  Bins     95
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g225670_4.reg
-> ... and files: ad63007000g200170h.evt ad63007000g200270m.evt ad63007000g200370l.evt ad63007000g200470h.evt ad63007000g200670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786       306          57480         0         0         0
 Writing events file
    306 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105       223          37882         0         0         0
 Writing events file
    529 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452         5            447         0         0         0
 Writing events file
    534 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988         8            980         0         0         0
 Writing events file
    542 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458         2            456         0         0         0
 Writing events file
    544 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         97789       544          97245         0         0         0
   in   88108.63 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200070_4.lc with binsize 8098.21970857515
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.88E+05      544      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            544       544              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           544       544              0         0         0         0
   in   88108.63 seconds
 Fits light curve has      544 counts for 6.1742E-03 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > set binsize 8098.21970857515
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad63007000g200070_4.lc
Wrote FITS light curve to file ad63007000g200070_4.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad63007000g200070_4_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g200070_4.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......            6        Bin Time (s) ......    8098.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS2
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        26 Newbins of       8098.22     (s) 

 
 Intv    1   Start 9928  6:27:42
     Ser.1     Avg 0.6869E-02    Chisq  6.219       Var 0.1495E-05 Newbs.     6
               Min 0.5743E-02      Max 0.9107E-02expVar 0.1442E-05  Bins      6

             Results from Statistical Analysis

             Newbin Integration Time (s)..  8098.2    
             Interval Duration (s)........ 0.14577E+06
             No. of Newbins ..............       6
             Average (c/s) ............... 0.68692E-02  +/-    0.54E-03
             Standard Deviation (c/s)..... 0.12225E-02
             Minimum (c/s)................ 0.57426E-02
             Maximum (c/s)................ 0.91072E-02
             Variance ((c/s)**2).......... 0.14946E-05 +/-    0.95E-06
             Expected Variance ((c/s)**2). 0.14420E-05 +/-    0.91E-06
             Third Moment ((c/s)**3)...... 0.14494E-08
             Average Deviation (c/s)...... 0.10510E-02
             Skewness..................... 0.79327        +/-     1.0    
             Kurtosis.....................-0.81218        +/-     2.0    
             RMS fractional variation....< 0.29904     (3 sigma)
             Chi-Square...................  6.2189        dof       5
             Chi-Square Prob of constancy. 0.28543     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.22808     (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        26 Newbins of       8098.22     (s) 

 
 Intv    1   Start 9928  6:27:42
     Ser.1     Avg 0.6869E-02    Chisq  6.219       Var 0.1495E-05 Newbs.     6
               Min 0.5743E-02      Max 0.9107E-02expVar 0.1442E-05  Bins      6
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> TIMEDEL=4.8828125000E-04 for ad63007000g300170h.evt
-> TIMEDEL=3.9062500000E-03 for ad63007000g300270m.evt
-> TIMEDEL=1.5625000000E-02 for ad63007000g300370l.evt
-> TIMEDEL=4.8828125000E-04 for ad63007000g300470h.evt
-> TIMEDEL=3.9062500000E-03 for ad63007000g300670m.evt
-> Minimum bin size is 1.5625000000E-02 seconds
-> Extracting events from region ad63007000g325670_1.reg
-> ... and files: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     14089          48309         0         0         0
 Writing events file
  14089 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      9097          31487         0         0         0
 Writing events file
  23186 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       109            409         0         0         0
 Writing events file
  23295 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       274            856         0         0         0
 Writing events file
  23569 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       110            406         0         0         0
 Writing events file
  23679 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146     23679          81467         0         0         0
   in   89004.24 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300070_1.lc with binsize 187.939194496654
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.89E+05    23679      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
          23679     23679              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         23679     23679              0         0         0         0
   in   89004.24 seconds
 Fits light curve has    23679 counts for 0.2660     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set binsize 187.939194496654
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad63007000g300070_1.lc
Wrote FITS light curve to file ad63007000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad63007000g300070_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g300070_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......          484        Bin Time (s) ......    187.9
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS3
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       404.192     (s) 

 
 Intv    1   Start 9927 23:28:47
     Ser.1     Avg 0.2665        Chisq  222.0       Var 0.8934E-03 Newbs.   255
               Min 0.1904          Max 0.3526    expVar 0.9406E-03  Bins    484

             Results from Statistical Analysis

             Newbin Integration Time (s)..  404.19    
             Interval Duration (s)........ 0.20331E+06
             No. of Newbins ..............     255
             Average (c/s) ............... 0.26654      +/-    0.19E-02
             Standard Deviation (c/s)..... 0.29890E-01
             Minimum (c/s)................ 0.19041    
             Maximum (c/s)................ 0.35264    
             Variance ((c/s)**2).......... 0.89341E-03 +/-    0.79E-04
             Expected Variance ((c/s)**2). 0.94058E-03 +/-    0.83E-04
             Third Moment ((c/s)**3)...... 0.95568E-06
             Average Deviation (c/s)...... 0.23879E-01
             Skewness..................... 0.35788E-01    +/-    0.15    
             Kurtosis.....................-0.81505E-01    +/-    0.31    
             RMS fractional variation....< 0.66845E-01 (3 sigma)
             Chi-Square...................  222.03        dof     254
             Chi-Square Prob of constancy. 0.92688     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.24171E-02 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       512 Newbins of       404.192     (s) 

 
 Intv    1   Start 9927 23:28:47
     Ser.1     Avg 0.2665        Chisq  222.0       Var 0.8934E-03 Newbs.   255
               Min 0.1904          Max 0.3526    expVar 0.9406E-03  Bins    484
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g325670_2.reg
-> ... and files: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      5746          56652         0         0         0
 Writing events file
   5746 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      3731          36853         0         0         0
 Writing events file
   9477 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        51            467         0         0         0
 Writing events file
   9528 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       103           1027         0         0         0
 Writing events file
   9631 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        43            473         0         0         0
 Writing events file
   9674 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146      9674          95472         0         0         0
   in   89004.24 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300070_2.lc with binsize 460.017798892524
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.89E+05     9674      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           9674      9674              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          9674      9674              0         0         0         0
   in   89004.24 seconds
 Fits light curve has     9674 counts for 0.1087     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set binsize 460.017798892524
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad63007000g300070_2.lc
Wrote FITS light curve to file ad63007000g300070_2.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad63007000g300070_2_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g300070_2.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......          195        Bin Time (s) ......    460.0
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS3
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       450 Newbins of       460.018     (s) 

 
 Intv    1   Start 9927 23:32:48
     Ser.1     Avg 0.1094        Chisq  266.2       Var 0.3729E-03 Newbs.   195
               Min 0.6987E-01      Max 0.1705    expVar 0.2732E-03  Bins    195

             Results from Statistical Analysis

             Newbin Integration Time (s)..  460.02    
             Interval Duration (s)........ 0.20287E+06
             No. of Newbins ..............     195
             Average (c/s) ............... 0.10941      +/-    0.12E-02
             Standard Deviation (c/s)..... 0.19310E-01
             Minimum (c/s)................ 0.69866E-01
             Maximum (c/s)................ 0.17054    
             Variance ((c/s)**2).......... 0.37288E-03 +/-    0.38E-04
             Expected Variance ((c/s)**2). 0.27318E-03 +/-    0.28E-04
             Third Moment ((c/s)**3)...... 0.30619E-05
             Average Deviation (c/s)...... 0.15191E-01
             Skewness..................... 0.42524        +/-    0.18    
             Kurtosis..................... 0.95376E-01    +/-    0.35    
             RMS fractional variation..... 0.91259E-01    +/-    0.17E-01
             Chi-Square...................  266.16        dof     194
             Chi-Square Prob of constancy. 0.44889E-03 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.41916E-02 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       450 Newbins of       460.018     (s) 

 
 Intv    1   Start 9927 23:32:48
     Ser.1     Avg 0.1094        Chisq  266.2       Var 0.3729E-03 Newbs.   195
               Min 0.6987E-01      Max 0.1705    expVar 0.2732E-03  Bins    195
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g325670_3.reg
-> ... and files: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      2273          60125         0         0         0
 Writing events file
   2273 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      1398          39186         0         0         0
 Writing events file
   3671 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        10            508         0         0         0
 Writing events file
   3681 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130        43           1087         0         0         0
 Writing events file
   3724 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        23            493         0         0         0
 Writing events file
   3747 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146      3747         101399         0         0         0
   in   89004.24 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300070_3.lc with binsize 1187.67338844043
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.89E+05     3747      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
           3747      3747              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3747      3747              0         0         0         0
   in   89004.24 seconds
 Fits light curve has     3747 counts for 4.2099E-02 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set binsize 1187.67338844043
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad63007000g300070_3.lc
Wrote FITS light curve to file ad63007000g300070_3.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad63007000g300070_3_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g300070_3.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......           71        Bin Time (s) ......    1188.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS3
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with       175 Newbins of       1187.67     (s) 

 
 Intv    1   Start 9927 23:44:35
     Ser.1     Avg 0.4174E-01    Chisq  66.65       Var 0.4152E-04 Newbs.    71
               Min 0.2610E-01      Max 0.5743E-01expVar 0.4423E-04  Bins     71

             Results from Statistical Analysis

             Newbin Integration Time (s)..  1187.7    
             Interval Duration (s)........ 0.20190E+06
             No. of Newbins ..............      71
             Average (c/s) ............... 0.41740E-01  +/-    0.79E-03
             Standard Deviation (c/s)..... 0.64437E-02
             Minimum (c/s)................ 0.26101E-01
             Maximum (c/s)................ 0.57429E-01
             Variance ((c/s)**2).......... 0.41522E-04 +/-    0.70E-05
             Expected Variance ((c/s)**2). 0.44230E-04 +/-    0.75E-05
             Third Moment ((c/s)**3)......-0.43255E-07
             Average Deviation (c/s)...... 0.50884E-02
             Skewness.....................-0.16167        +/-    0.29    
             Kurtosis.....................-0.61300E-01    +/-    0.58    
             RMS fractional variation....< 0.12792     (3 sigma)
             Chi-Square...................  66.652        dof      70
             Chi-Square Prob of constancy. 0.59128     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.24090     (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with       175 Newbins of       1187.67     (s) 

 
 Intv    1   Start 9927 23:44:35
     Ser.1     Avg 0.4174E-01    Chisq  66.65       Var 0.4152E-04 Newbs.    71
               Min 0.2610E-01      Max 0.5743E-01expVar 0.4423E-04  Bins     71
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Extracting events from region ad63007000g325670_4.reg
-> ... and files: ad63007000g300170h.evt ad63007000g300270m.evt ad63007000g300370l.evt ad63007000g300470h.evt ad63007000g300670m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
      5 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398       503          61895         0         0         0
 Writing events file
    503 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584       350          40234         0         0         0
 Writing events file
    853 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518         5            513         0         0         0
 Writing events file
    858 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130         6           1124         0         0         0
 Writing events file
    864 events written to the output file
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516         6            510         0         0         0
 Writing events file
    870 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        105146       870         104276         0         0         0
   in   89004.24 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300070_4.lc with binsize 5115.18642124859
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     29/07/95 22:35:18 0.89E+05      870      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            870       870              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           870       870              0         0         0         0
   in   89004.24 seconds
 Fits light curve has      870 counts for 9.7748E-03 counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > set binsize 5115.18642124859
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad63007000g300070_4.lc
Wrote FITS light curve to file ad63007000g300070_4.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad63007000g300070_4_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad63007000g300070_4.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ M31                 Start Time (d) ....  9927 22:35:18.549
 FITS Extension ....  1 - `RATE      `   Stop Time (d) .....  9930 08:00:22.549
 No. of Rows .......           11        Bin Time (s) ......    5115.
 Right Ascension ... 1.0698E+01          Internal time sys.. Converted to TJD
 Declination ....... 4.1360E+01          Experiment ........ ASCA     GIS3
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        41 Newbins of       5115.19     (s) 

 
 Intv    1   Start 9928  6:24:12
     Ser.1     Avg 0.9962E-02    Chisq  9.317       Var 0.2874E-05 Newbs.    11
               Min 0.6963E-02      Max 0.1290E-01expVar 0.3394E-05  Bins     11

             Results from Statistical Analysis

             Newbin Integration Time (s)..  5115.2    
             Interval Duration (s)........ 0.16880E+06
             No. of Newbins ..............      11
             Average (c/s) ............... 0.99623E-02  +/-    0.58E-03
             Standard Deviation (c/s)..... 0.16954E-02
             Minimum (c/s)................ 0.69628E-02
             Maximum (c/s)................ 0.12896E-01
             Variance ((c/s)**2).......... 0.28744E-05 +/-    0.13E-05
             Expected Variance ((c/s)**2). 0.33937E-05 +/-    0.15E-05
             Third Moment ((c/s)**3)...... 0.15836E-09
             Average Deviation (c/s)...... 0.14527E-02
             Skewness..................... 0.32496E-01    +/-    0.74    
             Kurtosis.....................-0.91591        +/-     1.5    
             RMS fractional variation....< 0.26360     (3 sigma)
             Chi-Square...................  9.3165        dof      10
             Chi-Square Prob of constancy. 0.50228     (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.25965E-02 (0 means < 1.e-38)
 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        41 Newbins of       5115.19     (s) 

 
 Intv    1   Start 9928  6:24:12
     Ser.1     Avg 0.9962E-02    Chisq  9.317       Var 0.2874E-05 Newbs.    11
               Min 0.6963E-02      Max 0.1290E-01expVar 0.3394E-05  Bins     11
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos>
-> Merging GTIs from the following files:
ad63007000g200170h.evt[2]
ad63007000g200270m.evt[2]
ad63007000g200370l.evt[2]
ad63007000g200470h.evt[2]
ad63007000g200670m.evt[2]
-> Making L1 light curve of ft950729_2235_0800G2HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve: 134771 output records from  135008  good input G2_L1    records.
-> Making L1 light curve of ft950729_2235_0800G2HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  83233 output records from  167966  good input G2_L1    records.
-> Merging GTIs from the following files:
ad63007000g300170h.evt[2]
ad63007000g300270m.evt[2]
ad63007000g300370l.evt[2]
ad63007000g300470h.evt[2]
ad63007000g300670m.evt[2]
-> Making L1 light curve of ft950729_2235_0800G3HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve: 132643 output records from  132888  good input G3_L1    records.
-> Making L1 light curve of ft950729_2235_0800G3HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:  83423 output records from  165626  good input G3_L1    records.

Extracting source event files ( 15:34:49 )

-> Extracting unbinned light curve ad63007000g200170h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786     11996          45790         0         0         0
 Writing events file
  11996 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786     11996          45790         0         0         0
   in   52066.59 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200170h_1.ulc use_events=yes
Wrote events list to file ad63007000g200170h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200170h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      6157          51629         0         0         0
 Writing events file
   6157 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786      6157          51629         0         0         0
   in   52066.59 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200170h_2.ulc use_events=yes
Wrote events list to file ad63007000g200170h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200170h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786      2705          55081         0         0         0
 Writing events file
   2705 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786      2705          55081         0         0         0
   in   52066.59 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200170h_3.ulc use_events=yes
Wrote events list to file ad63007000g200170h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200170h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.52E+05    57786      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          57786       306          57480         0         0         0
 Writing events file
    306 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         57786       306          57480         0         0         0
   in   52066.59 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200170h_4.ulc use_events=yes
Wrote events list to file ad63007000g200170h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200270m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      7927          30178         0         0         0
 Writing events file
   7927 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105      7927          30178         0         0         0
   in   34212.32 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200270m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200270m_1.ulc use_events=yes
Wrote events list to file ad63007000g200270m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200270m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      4081          34024         0         0         0
 Writing events file
   4081 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105      4081          34024         0         0         0
   in   34212.32 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200270m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200270m_2.ulc use_events=yes
Wrote events list to file ad63007000g200270m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200270m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105      1842          36263         0         0         0
 Writing events file
   1842 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105      1842          36263         0         0         0
   in   34212.32 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200270m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200270m_3.ulc use_events=yes
Wrote events list to file ad63007000g200270m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200270m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    38105      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          38105       223          37882         0         0         0
 Writing events file
    223 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         38105       223          37882         0         0         0
   in   34212.32 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200270m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200270m_4.ulc use_events=yes
Wrote events list to file ad63007000g200270m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200370l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        97            355         0         0         0
 Writing events file
     97 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452        97            355         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200370l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200370l_1.ulc use_events=yes
Wrote events list to file ad63007000g200370l_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200370l_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        59            393         0         0         0
 Writing events file
     59 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452        59            393         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200370l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200370l_2.ulc use_events=yes
Wrote events list to file ad63007000g200370l_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200370l_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452        35            417         0         0         0
 Writing events file
     35 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452        35            417         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200370l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200370l_3.ulc use_events=yes
Wrote events list to file ad63007000g200370l_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200370l_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      452      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            452         5            447         0         0         0
 Writing events file
      5 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           452         5            447         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200370l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200370l_4.ulc use_events=yes
Wrote events list to file ad63007000g200370l_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200370l_4.ulc since it has 5 events
-> Extracting unbinned light curve ad63007000g200470h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988       214            774         0         0         0
 Writing events file
    214 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988       214            774         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200470h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200470h_1.ulc use_events=yes
Wrote events list to file ad63007000g200470h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200470h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        91            897         0         0         0
 Writing events file
     91 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988        91            897         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200470h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200470h_2.ulc use_events=yes
Wrote events list to file ad63007000g200470h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200470h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988        61            927         0         0         0
 Writing events file
     61 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988        61            927         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200470h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200470h_3.ulc use_events=yes
Wrote events list to file ad63007000g200470h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200470h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03      988      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            988         8            980         0         0         0
 Writing events file
      8 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           988         8            980         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200470h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200470h_4.ulc use_events=yes
Wrote events list to file ad63007000g200470h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200470h_4.ulc since it has 8 events
-> Extracting unbinned light curve ad63007000g200670m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458       100            358         0         0         0
 Writing events file
    100 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458       100            358         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200670m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200670m_1.ulc use_events=yes
Wrote events list to file ad63007000g200670m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200670m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        43            415         0         0         0
 Writing events file
     43 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458        43            415         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200670m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200670m_2.ulc use_events=yes
Wrote events list to file ad63007000g200670m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200670m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458        25            433         0         0         0
 Writing events file
     25 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458        25            433         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200670m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_3.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200670m_3.ulc use_events=yes
Wrote events list to file ad63007000g200670m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g200670m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      458      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            458         2            456         0         0         0
 Writing events file
      2 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           458         2            456         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200670m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region ad63007000g225670_4.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad63007000g200670m_4.ulc use_events=yes
Wrote events list to file ad63007000g200670m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200670m_4.ulc since it has 2 events
-> Extracting unbinned light curve ad63007000g300170h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398     14089          48309         0         0         0
 Writing events file
  14089 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398     14089          48309         0         0         0
   in   53010.41 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300170h_1.ulc use_events=yes
Wrote events list to file ad63007000g300170h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300170h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      5746          56652         0         0         0
 Writing events file
   5746 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398      5746          56652         0         0         0
   in   53010.41 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300170h_2.ulc use_events=yes
Wrote events list to file ad63007000g300170h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300170h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398      2273          60125         0         0         0
 Writing events file
   2273 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398      2273          60125         0         0         0
   in   53010.41 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300170h_3.ulc use_events=yes
Wrote events list to file ad63007000g300170h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300170h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.53E+05    62398      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          62398       503          61895         0         0         0
 Writing events file
    503 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         62398       503          61895         0         0         0
   in   53010.41 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300170h_4.ulc use_events=yes
Wrote events list to file ad63007000g300170h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300270m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      9097          31487         0         0         0
 Writing events file
   9097 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584      9097          31487         0         0         0
   in   34164.12 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300270m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300270m_1.ulc use_events=yes
Wrote events list to file ad63007000g300270m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300270m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      3731          36853         0         0         0
 Writing events file
   3731 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584      3731          36853         0         0         0
   in   34164.12 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300270m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300270m_2.ulc use_events=yes
Wrote events list to file ad63007000g300270m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300270m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584      1398          39186         0         0         0
 Writing events file
   1398 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584      1398          39186         0         0         0
   in   34164.12 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300270m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300270m_3.ulc use_events=yes
Wrote events list to file ad63007000g300270m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300270m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.34E+05    40584      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          40584       350          40234         0         0         0
 Writing events file
    350 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         40584       350          40234         0         0         0
   in   34164.12 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300270m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300270m_4.ulc use_events=yes
Wrote events list to file ad63007000g300270m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300370l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518       109            409         0         0         0
 Writing events file
    109 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518       109            409         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300370l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300370l_1.ulc use_events=yes
Wrote events list to file ad63007000g300370l_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300370l_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        51            467         0         0         0
 Writing events file
     51 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518        51            467         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300370l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300370l_2.ulc use_events=yes
Wrote events list to file ad63007000g300370l_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300370l_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518        10            508         0         0         0
 Writing events file
     10 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518        10            508         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300370l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300370l_3.ulc use_events=yes
Wrote events list to file ad63007000g300370l_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300370l_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.42E+03      518      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            518         5            513         0         0         0
 Writing events file
      5 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           518         5            513         0         0         0
   in     415.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300370l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300370l_4.ulc use_events=yes
Wrote events list to file ad63007000g300370l_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300370l_4.ulc since it has 5 events
-> Extracting unbinned light curve ad63007000g300470h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       274            856         0         0         0
 Writing events file
    274 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130       274            856         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300470h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300470h_1.ulc use_events=yes
Wrote events list to file ad63007000g300470h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300470h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130       103           1027         0         0         0
 Writing events file
    103 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130       103           1027         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300470h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300470h_2.ulc use_events=yes
Wrote events list to file ad63007000g300470h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300470h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130        43           1087         0         0         0
 Writing events file
     43 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130        43           1087         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300470h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300470h_3.ulc use_events=yes
Wrote events list to file ad63007000g300470h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300470h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1130      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1130         6           1124         0         0         0
 Writing events file
      6 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1130         6           1124         0         0         0
   in     982.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300470h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300470h_4.ulc use_events=yes
Wrote events list to file ad63007000g300470h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300470h_4.ulc since it has 6 events
-> Extracting unbinned light curve ad63007000g300670m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516       110            406         0         0         0
 Writing events file
    110 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516       110            406         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300670m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300670m_1.ulc use_events=yes
Wrote events list to file ad63007000g300670m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300670m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        43            473         0         0         0
 Writing events file
     43 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516        43            473         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300670m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300670m_2.ulc use_events=yes
Wrote events list to file ad63007000g300670m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300670m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516        23            493         0         0         0
 Writing events file
     23 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516        23            493         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300670m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_3.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300670m_3.ulc use_events=yes
Wrote events list to file ad63007000g300670m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad63007000g300670m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.43E+03      516      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            516         6            510         0         0         0
 Writing events file
      6 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           516         6            510         0         0         0
   in     432.00 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300670m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region ad63007000g325670_4.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad63007000g300670m_4.ulc use_events=yes
Wrote events list to file ad63007000g300670m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300670m_4.ulc since it has 6 events
-> Extracting unbinned light curve ad63007000s000102h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      6940          38085         0         0         0
 Writing events file
   6940 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025      6940          38085         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000102h_1.ulc use_events=yes
Wrote events list to file ad63007000s000102h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000102h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025     12690          32335         0         0         0
 Writing events file
  12690 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025     12690          32335         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000102h_2.ulc use_events=yes
Wrote events list to file ad63007000s000102h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000102h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025      2336          42689         0         0         0
 Writing events file
   2336 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025      2336          42689         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000102h_3.ulc use_events=yes
Wrote events list to file ad63007000s000102h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000102h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.47E+05    45025 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          45025       615          44410         0         0         0
 Writing events file
    615 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         45025       615          44410         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000102h_4.ulc use_events=yes
Wrote events list to file ad63007000s000102h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000112h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      7821          42489         0         0         0
 Writing events file
   7821 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      7821          42489         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000112h_1.ulc use_events=yes
Wrote events list to file ad63007000s000112h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000112h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310     13974          36336         0         0         0
 Writing events file
  13974 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310     13974          36336         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000112h_2.ulc use_events=yes
Wrote events list to file ad63007000s000112h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000112h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310      2679          47631         0         0         0
 Writing events file
   2679 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310      2679          47631         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000112h_3.ulc use_events=yes
Wrote events list to file ad63007000s000112h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000112h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.47E+05    50310 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          50310       661          49649         0         0         0
 Writing events file
    661 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         50310       661          49649         0         0         0
   in   47221.93 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000112h_4.ulc use_events=yes
Wrote events list to file ad63007000s000112h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000202m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      4225          22035         0         0         0
 Writing events file
   4225 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260      4225          22035         0         0         0
   in   28575.86 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000202m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000202m_1.ulc use_events=yes
Wrote events list to file ad63007000s000202m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000202m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      7322          18938         0         0         0
 Writing events file
   7322 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260      7322          18938         0         0         0
   in   28575.86 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000202m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000202m_2.ulc use_events=yes
Wrote events list to file ad63007000s000202m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000202m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260      1421          24839         0         0         0
 Writing events file
   1421 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260      1421          24839         0         0         0
   in   28575.86 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000202m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000202m_3.ulc use_events=yes
Wrote events list to file ad63007000s000202m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000202m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.29E+05    26260 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          26260       386          25874         0         0         0
 Writing events file
    386 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         26260       386          25874         0         0         0
   in   28575.86 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000202m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000202m_4.ulc use_events=yes
Wrote events list to file ad63007000s000202m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000302h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        70            820         0         0         0
 Writing events file
     70 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890        70            820         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000302h_1.ulc use_events=yes
Wrote events list to file ad63007000s000302h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000302h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890       219            671         0         0         0
 Writing events file
    219 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890       219            671         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000302h_2.ulc use_events=yes
Wrote events list to file ad63007000s000302h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000302h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        57            833         0         0         0
 Writing events file
     57 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890        57            833         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000302h_3.ulc use_events=yes
Wrote events list to file ad63007000s000302h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000302h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.10E+04      890 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            890        19            871         0         0         0
 Writing events file
     19 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           890        19            871         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000302h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000302h_4.ulc use_events=yes
Wrote events list to file ad63007000s000302h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000312h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        96            995         0         0         0
 Writing events file
     96 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        96            995         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000312h_1.ulc use_events=yes
Wrote events list to file ad63007000s000312h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000312h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091       273            818         0         0         0
 Writing events file
    273 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091       273            818         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000312h_2.ulc use_events=yes
Wrote events list to file ad63007000s000312h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000312h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        64           1027         0         0         0
 Writing events file
     64 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        64           1027         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000312h_3.ulc use_events=yes
Wrote events list to file ad63007000s000312h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000312h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.10E+04     1091 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1091        22           1069         0         0         0
 Writing events file
     22 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1091        22           1069         0         0         0
   in    1007.30 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000312h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000312h_4.ulc use_events=yes
Wrote events list to file ad63007000s000312h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000402h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       365           1749         0         0         0
 Writing events file
    365 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       365           1749         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000402h_1.ulc use_events=yes
Wrote events list to file ad63007000s000402h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000402h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       589           1525         0         0         0
 Writing events file
    589 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       589           1525         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000402h_2.ulc use_events=yes
Wrote events list to file ad63007000s000402h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000402h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114       112           2002         0         0         0
 Writing events file
    112 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114       112           2002         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000402h_3.ulc use_events=yes
Wrote events list to file ad63007000s000402h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000402h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.23E+04     2114 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2114        33           2081         0         0         0
 Writing events file
     33 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2114        33           2081         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000402h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000402h_4.ulc use_events=yes
Wrote events list to file ad63007000s000402h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000412h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       414           1959         0         0         0
 Writing events file
    414 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       414           1959         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000412h_1.ulc use_events=yes
Wrote events list to file ad63007000s000412h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000412h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       643           1730         0         0         0
 Writing events file
    643 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       643           1730         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000412h_2.ulc use_events=yes
Wrote events list to file ad63007000s000412h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000412h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373       122           2251         0         0         0
 Writing events file
    122 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373       122           2251         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000412h_3.ulc use_events=yes
Wrote events list to file ad63007000s000412h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000412h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.23E+04     2373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           2373        38           2335         0         0         0
 Writing events file
     38 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2373        38           2335         0         0         0
   in    2301.77 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000412h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad63007000s000412h_4.ulc use_events=yes
Wrote events list to file ad63007000s000412h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s000502l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88         0             88         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000502l.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000502l_1.ulc use_events=yes
Wrote events list to file ad63007000s000502l_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000502l_1.ulc since it has 0 events
-> Extracting unbinned light curve ad63007000s000502l_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         6             82         0         0         0
 Writing events file
      6 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88         6             82         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000502l.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000502l_2.ulc use_events=yes
Wrote events list to file ad63007000s000502l_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000502l_2.ulc since it has 6 events
-> Extracting unbinned light curve ad63007000s000502l_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         1             87         0         0         0
 Writing events file
      1 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88         1             87         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000502l.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000502l_3.ulc use_events=yes
Wrote events list to file ad63007000s000502l_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000502l_3.ulc since it has 1 events
-> Extracting unbinned light curve ad63007000s000502l_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.39E+02       88 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             88         0             88         0         0         0
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            88         0             88         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000502l.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000502l_4.ulc use_events=yes
Wrote events list to file ad63007000s000502l_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000502l_4.ulc since it has 0 events
-> Extracting unbinned light curve ad63007000s000602m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        53            367         0         0         0
 Writing events file
     53 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420        53            367         0         0         0
   in    1450.36 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000602m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000602m_1.ulc use_events=yes
Wrote events list to file ad63007000s000602m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000602m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420       108            312         0         0         0
 Writing events file
    108 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420       108            312         0         0         0
   in    1450.36 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000602m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_2.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000602m_2.ulc use_events=yes
Wrote events list to file ad63007000s000602m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000602m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420        26            394         0         0         0
 Writing events file
     26 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420        26            394         0         0         0
   in    1450.36 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000602m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_3.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000602m_3.ulc use_events=yes
Wrote events list to file ad63007000s000602m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s000602m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.15E+04      420 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            420         5            415         0         0         0
 Writing events file
      5 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           420         5            415         0         0         0
   in    1450.36 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s000602m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad63007000s032002_4.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad63007000s000602m_4.ulc use_events=yes
Wrote events list to file ad63007000s000602m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000602m_4.ulc since it has 5 events
-> Extracting unbinned light curve ad63007000s100102h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      4203          31394         0         0         0
 Writing events file
   4203 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597      4203          31394         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100102h_1.ulc use_events=yes
Wrote events list to file ad63007000s100102h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100102h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      9050          26547         0         0         0
 Writing events file
   9050 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597      9050          26547         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100102h_2.ulc use_events=yes
Wrote events list to file ad63007000s100102h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100102h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597      2579          33018         0         0         0
 Writing events file
   2579 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597      2579          33018         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100102h_3.ulc use_events=yes
Wrote events list to file ad63007000s100102h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100102h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.51E+05    35597 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          35597       488          35109         0         0         0
 Writing events file
    488 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         35597       488          35109         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100102h_4.ulc use_events=yes
Wrote events list to file ad63007000s100102h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100112h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      5223          37590         0         0         0
 Writing events file
   5223 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      5223          37590         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100112h_1.ulc use_events=yes
Wrote events list to file ad63007000s100112h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100112h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813     10649          32164         0         0         0
 Writing events file
  10649 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813     10649          32164         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100112h_2.ulc use_events=yes
Wrote events list to file ad63007000s100112h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100112h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813      3062          39751         0         0         0
 Writing events file
   3062 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813      3062          39751         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100112h_3.ulc use_events=yes
Wrote events list to file ad63007000s100112h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100112h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.51E+05    42813 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          42813       568          42245         0         0         0
 Writing events file
    568 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         42813       568          42245         0         0         0
   in   50800.39 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100112h_4.ulc use_events=yes
Wrote events list to file ad63007000s100112h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100202m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      2514          17941         0         0         0
 Writing events file
   2514 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455      2514          17941         0         0         0
   in   30751.99 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100202m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100202m_1.ulc use_events=yes
Wrote events list to file ad63007000s100202m_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100202m_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      5027          15428         0         0         0
 Writing events file
   5027 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455      5027          15428         0         0         0
   in   30751.99 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100202m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100202m_2.ulc use_events=yes
Wrote events list to file ad63007000s100202m_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100202m_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455      1448          19007         0         0         0
 Writing events file
   1448 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455      1448          19007         0         0         0
   in   30751.99 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100202m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100202m_3.ulc use_events=yes
Wrote events list to file ad63007000s100202m_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100202m_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.31E+05    20455 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
          20455       291          20164         0         0         0
 Writing events file
    291 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         20455       291          20164         0         0         0
   in   30751.99 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100202m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100202m_4.ulc use_events=yes
Wrote events list to file ad63007000s100202m_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100302l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         3             98         0         0         0
 Writing events file
      3 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101         3             98         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100302l.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100302l_1.ulc use_events=yes
Wrote events list to file ad63007000s100302l_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s100302l_1.ulc since it has 3 events
-> Extracting unbinned light curve ad63007000s100302l_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
      7 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101         7             94         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100302l.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100302l_2.ulc use_events=yes
Wrote events list to file ad63007000s100302l_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s100302l_2.ulc since it has 7 events
-> Extracting unbinned light curve ad63007000s100302l_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         7             94         0         0         0
 Writing events file
      7 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101         7             94         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100302l.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100302l_3.ulc use_events=yes
Wrote events list to file ad63007000s100302l_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s100302l_3.ulc since it has 7 events
-> Extracting unbinned light curve ad63007000s100302l_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.39E+02      101 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            101         0            101         0         0         0
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           101         0            101         0         0         0
   in      38.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100302l.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100302l_4.ulc use_events=yes
Wrote events list to file ad63007000s100302l_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s100302l_4.ulc since it has 0 events
-> Extracting unbinned light curve ad63007000s100402h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        97            605         0         0         0
 Writing events file
     97 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702        97            605         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100402h_1.ulc use_events=yes
Wrote events list to file ad63007000s100402h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100402h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702       168            534         0         0         0
 Writing events file
    168 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702       168            534         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100402h_2.ulc use_events=yes
Wrote events list to file ad63007000s100402h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100402h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        43            659         0         0         0
 Writing events file
     43 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702        43            659         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100402h_3.ulc use_events=yes
Wrote events list to file ad63007000s100402h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100402h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.10E+04      702 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            702        16            686         0         0         0
 Writing events file
     16 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           702        16            686         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100402h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad63007000s100402h_4.ulc use_events=yes
Wrote events list to file ad63007000s100402h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad63007000s100412h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835       116            719         0         0         0
 Writing events file
    116 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835       116            719         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100412h_1.ulc use_events=yes
Wrote events list to file ad63007000s100412h_1.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100412h_2.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835       207            628         0         0         0
 Writing events file
    207 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835       207            628         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_2.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100412h_2.ulc use_events=yes
Wrote events list to file ad63007000s100412h_2.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100412h_3.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835        55            780         0         0         0
 Writing events file
     55 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835        55            780         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_3.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100412h_3.ulc use_events=yes
Wrote events list to file ad63007000s100412h_3.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad63007000s100412h_4.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.10E+04      835 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            835        18            817         0         0         0
 Writing events file
     18 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           835        18            817         0         0         0
   in    1001.72 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000s100412h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad63007000s132002_4.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad63007000s100412h_4.ulc use_events=yes
Wrote events list to file ad63007000s100412h_4.ulc
Changing Data directory from:
    /data/data19/seq_proc/63007000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

Extracting FRAME mode data ( 17:13:05 )

-> Extracting frame mode data from ft950729_2235.0800
-> Standard Output From STOOL tlmFrm:
 *** tlmFrm Version 1.1 (1997-08-25) *** 
total number of superframes: 37587

Total of 0 sets of frame data are extracted.

Extracting GIS calibration source spectra ( 17:15:10 )

-> Standard Output From STOOL group_event_files:
1 ad63007000g200170h.unf 202801
1 ad63007000g200270m.unf 202801
1 ad63007000g200370l.unf 202801
1 ad63007000g200470h.unf 202801
1 ad63007000g200570l.unf 202801
1 ad63007000g200670m.unf 202801
-> Fetching GIS2_CALSRC256.2
-> Extracting ad63007000g220170.cal from ad63007000g200170h.unf ad63007000g200270m.unf ad63007000g200370l.unf ad63007000g200470h.unf ad63007000g200570l.unf ad63007000g200670m.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
      5 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1422      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
      5 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1422      256
      6 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      782      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          99435     13669          85764         2         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          80521     12981          67540         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          19133      5791          13341         1         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1508       236           1271         1         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200570l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1422       511            911         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            782       133            649         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        202801     33321         169476         4         0         0
   in  146549.04 seconds
 Spectrum         has    33321 counts for 0.2274     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200270m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200370l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200470h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200570l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > read events ad63007000g200670m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad63007000g220170.cal group=yes
Wrote spectrum to ad63007000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0_256ch.rmf already present in current directory
-> Plotting ad63007000g220170_cal.ps and finding peak
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 17:17:18 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad63007000g220170.cal
 Net count rate (cts/s) for file   1  0.2274    +/-  1.2457E-03
   1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
 Input parameter value, delta, min, bot, top, and max values for ...
 Mod parameter  1 of component  1 constant factor
    1.000      1.0000E-02      0.          0.      1.0000E+10  1.0000E+10
!
 Mod parameter  2 of component  2 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 5.9
 Mod parameter  3 of component  2 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  4 of component  2 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
 Mod parameter  5 of component  3 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 6.5
 Mod parameter  6 of component  3 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  7 of component  3 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/-      0.
    2    2    2       gaussian/b  LineE      5.90000     +/-      0.
    3    3    2       gaussian/b  Sigma           0.     +/-      0.
    4    4    2       gaussian/b  norm       1.00000     +/-      0.
    5    5    3       gaussian/b  LineE      6.50000     +/-      0.
    6    6    3       gaussian/b  Sigma           0.     +/-      0.
    7    7    3       gaussian/b  norm       1.00000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
    7 variable fit parameters
 Chi-Squared =     4.1120E+06 using    84 PHA bins.
 Reduced chi-squared =     5.3402E+04
!XSPEC> newpar 5 = 2 1.101005
    6 variable fit parameters
 Chi-Squared =     4.0794E+06 using    84 PHA bins.
 Reduced chi-squared =     5.2300E+04
!XSPEC> newpar 6 = 3 1.049288
    5 variable fit parameters
 Chi-Squared =     4.0794E+06 using    84 PHA bins.
 Reduced chi-squared =     5.1638E+04
!XSPEC> renorm
 Chi-Squared =     1.0614E+04 using    84 PHA bins.
 Reduced chi-squared =      134.4
!XSPEC> fit
 Chi-Squared  Lvl  Fit param # 1     2           3           4
                 5
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   8370.5      0      1.000       5.892      0.1008      6.8974E-02
              5.9731E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   2782.3      0      1.000       5.857      0.1558      0.1074
              5.2355E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   893.74     -1      1.000       5.889      0.1759      0.1517
              3.6483E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   752.13     -2      1.000       5.922      0.1943      0.1670
              2.6025E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   748.19     -3      1.000       5.916      0.1896      0.1653
              2.7611E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   748.13     -4      1.000       5.917      0.1901      0.1657
              2.7255E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   748.09     -5      1.000       5.916      0.1899      0.1656
              2.7336E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   748.09      0      1.000       5.916      0.1899      0.1656
              2.7333E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/- -1.0000
    2    2    2       gaussian/b  LineE      5.91649     +/- 0.31137E-02
    3    3    2       gaussian/b  Sigma     0.189898     +/- 0.32985E-02
    4    4    2       gaussian/b  norm      0.165605     +/- 0.13869E-02
    5    2    3       gaussian/b  LineE      6.51409     = par   2 *  1.1010
    6    3    3       gaussian/b  Sigma     0.199258     = par   3 *  1.0493
    7    5    3       gaussian/b  norm      2.733286E-02 +/- 0.97450E-03
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      748.1     using    84 PHA bins.
 Reduced chi-squared =      9.469
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Calibration source ad63007000g220170.cal peaks at 5.91649 +/- 0.0031137 keV
-> Standard Output From STOOL group_event_files:
1 ad63007000g300170h.unf 202619
1 ad63007000g300270m.unf 202619
1 ad63007000g300370l.unf 202619
1 ad63007000g300470h.unf 202619
1 ad63007000g300570l.unf 202619
1 ad63007000g300670m.unf 202619
-> Fetching GIS3_CALSRC256.2
-> Extracting ad63007000g320170.cal from ad63007000g300170h.unf ad63007000g300270m.unf ad63007000g300370l.unf ad63007000g300470h.unf ad63007000g300570l.unf ad63007000g300670m.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
      5 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1329      256
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
      2 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
      3 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
      4 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
      5 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1329      256
      6 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      850      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102159     13122          89037         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          78760     11506          67253         1         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          17963      5291          12672         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1558       196           1362         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300570l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1329       467            862         0         0         0
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            850       155            695         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        202619     30737         171881         1         0         0
   in  148675.03 seconds
 Spectrum         has    30737 counts for 0.2067     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!xsel:ASCA > read events ad63007000g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300270m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300370l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300470h.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   4
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300570l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   5
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > read events ad63007000g300670m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   6
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad63007000g320170.cal group=yes
Wrote spectrum to ad63007000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0_256ch.rmf already present in current directory
-> Plotting ad63007000g320170_cal.ps and finding peak
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 17:19:47 12-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad63007000g320170.cal
 Net count rate (cts/s) for file   1  0.2067    +/-  1.1793E-03
   1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
 Input parameter value, delta, min, bot, top, and max values for ...
 Mod parameter  1 of component  1 constant factor
    1.000      1.0000E-02      0.          0.      1.0000E+10  1.0000E+10
!
 Mod parameter  2 of component  2 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 5.9
 Mod parameter  3 of component  2 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  4 of component  2 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
 Mod parameter  5 of component  3 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 6.5
 Mod parameter  6 of component  3 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  7 of component  3 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/-      0.
    2    2    2       gaussian/b  LineE      5.90000     +/-      0.
    3    3    2       gaussian/b  Sigma           0.     +/-      0.
    4    4    2       gaussian/b  norm       1.00000     +/-      0.
    5    5    3       gaussian/b  LineE      6.50000     +/-      0.
    6    6    3       gaussian/b  Sigma           0.     +/-      0.
    7    7    3       gaussian/b  norm       1.00000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
    7 variable fit parameters
 Chi-Squared =     4.6966E+06 using    84 PHA bins.
 Reduced chi-squared =     6.0994E+04
!XSPEC> newpar 5 = 2 1.101005
    6 variable fit parameters
 Chi-Squared =     4.6585E+06 using    84 PHA bins.
 Reduced chi-squared =     5.9725E+04
!XSPEC> newpar 6 = 3 1.049288
    5 variable fit parameters
 Chi-Squared =     4.6585E+06 using    84 PHA bins.
 Reduced chi-squared =     5.8969E+04
!XSPEC> renorm
 Chi-Squared =     1.0799E+04 using    84 PHA bins.
 Reduced chi-squared =      136.7
!XSPEC> fit
 Chi-Squared  Lvl  Fit param # 1     2           3           4
                 5
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   8538.8      0      1.000       5.892      9.5146E-02  6.3255E-02
              5.3662E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   2853.8      0      1.000       5.863      0.1419      0.1028
              4.6049E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   637.07     -1      1.000       5.912      0.1516      0.1481
              2.8905E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   538.31     -2      1.000       5.928      0.1568      0.1591
              2.3199E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   534.93     -3      1.000       5.924      0.1527      0.1582
              2.4151E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   534.88     -4      1.000       5.924      0.1529      0.1584
              2.3969E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   534.85     -5      1.000       5.924      0.1528      0.1583
              2.4002E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   534.85      0      1.000       5.924      0.1528      0.1583
              2.4000E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/- -1.0000
    2    2    2       gaussian/b  LineE      5.92428     +/- 0.25133E-02
    3    3    2       gaussian/b  Sigma     0.152767     +/- 0.31351E-02
    4    4    2       gaussian/b  norm      0.158321     +/- 0.12197E-02
    5    2    3       gaussian/b  LineE      6.52266     = par   2 *  1.1010
    6    3    3       gaussian/b  Sigma     0.160297     = par   3 *  1.0493
    7    5    3       gaussian/b  norm      2.400046E-02 +/- 0.74520E-03
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      534.8     using    84 PHA bins.
 Reduced chi-squared =      6.770
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Calibration source ad63007000g320170.cal peaks at 5.92428 +/- 0.0025133 keV

Extracting bright and dark Earth event files. ( 17:20:08 )

-> Extracting bright and dark Earth events from ad63007000s000102h.unf
-> Extracting ad63007000s000102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.56E+05   708373 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         708373       654              0    707719         0         0
 Writing events file
    654 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        708373       654              0    707719         0         0
   in      44.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000102h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000102h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          654
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          72         216
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          31          93
cleaning chip #           2
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1           1           3
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          35         105
 
 Number of pixels rejected           :          139
 Number of (internal) image counts   :          654
 Number of image cts rejected (N, %) :          417     63.7614670
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            72           31            1           35
 
 Image counts      :           254          128          141          131
 Image cts rejected:           216           93            3          105
 Image cts rej (%) :         85.04        72.66         2.13        80.15
 
    filtering data...
 
 Total counts      :           254          128          141          131
 Total cts rejected:           216           93            3          105
 Total cts rej (%) :         85.04        72.66         2.13        80.15
 
 Number of clean counts accepted  :          237
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          139
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000112h.unf
-> Extracting ad63007000s000112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.56E+05   723651 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         723651       692              0    722959         0         0
 Writing events file
    692 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        723651       692              0    722959         0         0
   in      44.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000112h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad63007000s000112h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          692
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          76         228
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          31          93
cleaning chip #           2
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1           5          15
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          35         105
 
 Number of pixels rejected           :          147
 Number of (internal) image counts   :          692
 Number of image cts rejected (N, %) :          441     63.7283249
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            76           31            5           35
 
 Image counts      :           261          130          170          131
 Image cts rejected:           228           93           15          105
 Image cts rej (%) :         87.36        71.54         8.82        80.15
 
    filtering data...
 
 Total counts      :           261          130          170          131
 Total cts rejected:           228           93           15          105
 Total cts rej (%) :         87.36        71.54         8.82        80.15
 
 Number of clean counts accepted  :          251
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          147
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000202m.unf
-> Extracting ad63007000s000202m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 23:26:30 0.47E+05   563461 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000202m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         563461    126978              0    436483         0         0
 Writing events file
 126978 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        563461    126978              0    436483         0         0
   in   11949.16 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000202m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000202m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000202m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       126978
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              86       55418
 Flickering pixels iter, pixels & cnts :   1          18         843
cleaning chip #           1
 Hot pixels & counts                   :              43       24894
 Flickering pixels iter, pixels & cnts :   1          17         272
cleaning chip #           2
 Hot pixels & counts                   :              35       16041
 Flickering pixels iter, pixels & cnts :   1           7          41
cleaning chip #           3
 Hot pixels & counts                   :              45       26738
 Flickering pixels iter, pixels & cnts :   1          13         439
 
 Number of pixels rejected           :          264
 Number of (internal) image counts   :       126978
 Number of image cts rejected (N, %) :       124686     98.1949615
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :           104           60           42           58
 
 Image counts      :         56845        25774        16625        27734
 Image cts rejected:         56261        25166        16082        27177
 Image cts rej (%) :         98.97        97.64        96.73        97.99
 
    filtering data...
 
 Total counts      :         56845        25774        16625        27734
 Total cts rejected:         56261        25166        16082        27177
 Total cts rej (%) :         98.97        97.64        96.73        97.99
 
 Number of clean counts accepted  :         2292
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          264
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000302h.unf
-> Extracting ad63007000s000302h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 03:18:26 0.38E+04    24389 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s000302h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000302h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000302h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000s000312h.unf
-> Extracting ad63007000s000312h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 03:18:26 0.38E+04    28621 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s000312h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000312h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s000312h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000s000402h.unf
-> Extracting ad63007000s000402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 12:00:10 0.30E+04    42797 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s000402h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000402h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad63007000s000402h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000s000412h.unf
-> Extracting ad63007000s000412h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 12:00:10 0.30E+04    43809 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s000412h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000412h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s000412h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000s000502l.unf
-> Extracting ad63007000s000502l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 23:22:14 0.62E+04    46263 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000502l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          46263     32548              0     13715         0         0
 Writing events file
  32548 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         46263     32548              0     13715         0         0
   in    4419.87 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000502l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000502l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000502l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        32548
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              37        8254
 Flickering pixels iter, pixels & cnts :   1          16         289
cleaning chip #           1
 Hot pixels & counts                   :              39        8174
 Flickering pixels iter, pixels & cnts :   1          14         157
cleaning chip #           2
 Hot pixels & counts                   :              33        6105
 Flickering pixels iter, pixels & cnts :   1           6          76
cleaning chip #           3
 Hot pixels & counts                   :              41        8373
 Flickering pixels iter, pixels & cnts :   1          12         150
 
 Number of pixels rejected           :          198
 Number of (internal) image counts   :        32548
 Number of image cts rejected (N, %) :        31578     97.0197830
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            53           53           39           53
 
 Image counts      :          8704         8602         6471         8771
 Image cts rejected:          8543         8331         6181         8523
 Image cts rej (%) :         98.15        96.85        95.52        97.17
 
    filtering data...
 
 Total counts      :          8704         8602         6471         8771
 Total cts rejected:          8543         8331         6181         8523
 Total cts rej (%) :         98.15        96.85        95.52        97.17
 
 Number of clean counts accepted  :          970
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          198
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000602m.unf
-> Extracting ad63007000s000602m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.12E+05    18955 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000602m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          18955      3440              0     15515         0         0
 Writing events file
   3440 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         18955      3440              0     15515         0         0
   in     341.40 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000602m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000602m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000602m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3440
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              76        1495
 Flickering pixels iter, pixels & cnts :   1          18         120
cleaning chip #           1
 Hot pixels & counts                   :              38         696
 Flickering pixels iter, pixels & cnts :   1           5          22
cleaning chip #           2
 Hot pixels & counts                   :              23         238
 Flickering pixels iter, pixels & cnts :   1           6          25
cleaning chip #           3
 Hot pixels & counts                   :              38         686
 Flickering pixels iter, pixels & cnts :   1           9          51
 
 Number of pixels rejected           :          213
 Number of (internal) image counts   :         3440
 Number of image cts rejected (N, %) :         3333     96.8895340
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            94           43           29           47
 
 Image counts      :          1652          741          281          766
 Image cts rejected:          1615          718          263          737
 Image cts rej (%) :         97.76        96.90        93.59        96.21
 
    filtering data...
 
 Total counts      :          1652          741          281          766
 Total cts rejected:          1615          718          263          737
 Total cts rej (%) :         97.76        96.90        93.59        96.21
 
 Number of clean counts accepted  :          107
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          213
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000702l.unf
-> Extracting ad63007000s000702l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      30/07/95 00:14:30 0.19E+05     3089 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000702l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3089      2710              0       379         0         0
 Writing events file
   2710 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3089      2710              0       379         0         0
   in     433.57 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000702l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000702l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000702l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         2710
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              33         759
 Flickering pixels iter, pixels & cnts :   1          19         100
cleaning chip #           1
 Hot pixels & counts                   :              36         772
 Flickering pixels iter, pixels & cnts :   1          11          67
cleaning chip #           2
 Hot pixels & counts                   :              24         238
 Flickering pixels iter, pixels & cnts :   1           8          31
cleaning chip #           3
 Hot pixels & counts                   :              33         543
 Flickering pixels iter, pixels & cnts :   1          13          75
 
 Number of pixels rejected           :          177
 Number of (internal) image counts   :         2710
 Number of image cts rejected (N, %) :         2585     95.3874512
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            52           47           32           46
 
 Image counts      :           893          875          289          653
 Image cts rejected:           859          839          269          618
 Image cts rej (%) :         96.19        95.89        93.08        94.64
 
    filtering data...
 
 Total counts      :           893          875          289          653
 Total cts rejected:           859          839          269          618
 Total cts rej (%) :         96.19        95.89        93.08        94.64
 
 Number of clean counts accepted  :          125
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          177
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s000802l.unf
-> Extracting ad63007000s000802l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:58:46 0.67E+04     1099 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s000802l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1099       234              0       865         0         0
 Writing events file
    234 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1099       234              0       865         0         0
   in    3598.72 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s000802l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s000802l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s000802l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          234
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
cleaning chip #           1
 Hot pixels & counts                   :               0           0
cleaning chip #           2
 Hot pixels & counts                   :               0           0
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :          234
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :            64           57           50           63
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :            64           57           50           63
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :          234
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s100102h.unf
-> Extracting ad63007000s100102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 02:42:50 0.62E+05   677667 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100102h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         677667       576              0    677091         0         0
 Writing events file
    576 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        677667       576              0    677091         0         0
   in      44.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100102h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s100102h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s100102h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          576
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          40         120
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          44         132
cleaning chip #           2
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1           8          24
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          23          69
 
 Number of pixels rejected           :          115
 Number of (internal) image counts   :          576
 Number of image cts rejected (N, %) :          345     59.8958321
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            40           44            8           23
 
 Image counts      :           147          156          169          104
 Image cts rejected:           120          132           24           69
 Image cts rej (%) :         81.63        84.62        14.20        66.35
 
    filtering data...
 
 Total counts      :           147          156          169          104
 Total cts rejected:           120          132           24           69
 Total cts rej (%) :         81.63        84.62        14.20        66.35
 
 Number of clean counts accepted  :          231
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          115
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s100112h.unf
-> Extracting ad63007000s100112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 02:42:50 0.62E+05   699349 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100112h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         699349       631              0    698718         0         0
 Writing events file
    631 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        699349       631              0    698718         0         0
   in      44.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100112h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad63007000s100112h.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s100112h.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          631
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          39         117
cleaning chip #           1
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          45         135
cleaning chip #           2
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          11          33
cleaning chip #           3
 Hot pixels & counts                   :               0           0
 Flickering pixels iter, pixels & cnts :   1          25          75
 
 Number of pixels rejected           :          120
 Number of (internal) image counts   :          631
 Number of image cts rejected (N, %) :          360     57.0522995
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            39           45           11           25
 
 Image counts      :           150          162          209          110
 Image cts rejected:           117          135           33           75
 Image cts rej (%) :         78.00        83.33        15.79        68.18
 
    filtering data...
 
 Total counts      :           150          162          209          110
 Total cts rejected:           117          135           33           75
 Total cts rej (%) :         78.00        83.33        15.79        68.18
 
 Number of clean counts accepted  :          271
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          120
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s100202m.unf
-> Extracting ad63007000s100202m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   MEDIUM   29/07/95 22:35:02 0.60E+05   565354 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100202m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         565354    112563              0    452791         0         0
 Writing events file
 112563 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        565354    112563              0    452791         0         0
   in   12315.31 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100202m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s100202m.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s100202m.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :       112563
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              50       29236
 Flickering pixels iter, pixels & cnts :   1          12         402
cleaning chip #           1
 Hot pixels & counts                   :              54       32393
 Flickering pixels iter, pixels & cnts :   1          21         429
cleaning chip #           2
 Hot pixels & counts                   :              45       26544
 Flickering pixels iter, pixels & cnts :   1          18         416
cleaning chip #           3
 Hot pixels & counts                   :              38       20752
 Flickering pixels iter, pixels & cnts :   1          14         322
 
 Number of pixels rejected           :          252
 Number of (internal) image counts   :       112563
 Number of image cts rejected (N, %) :       110494     98.1619186
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            62           75           63           52
 
 Image counts      :         30095        33362        27542        21564
 Image cts rejected:         29638        32822        26960        21074
 Image cts rej (%) :         98.48        98.38        97.89        97.73
 
    filtering data...
 
 Total counts      :         30095        33362        27542        21564
 Total cts rejected:         29638        32822        26960        21074
 Total cts rej (%) :         98.48        98.38        97.89        97.73
 
 Number of clean counts accepted  :         2069
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          252
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s100302l.unf
-> Extracting ad63007000s100302l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   LOW      29/07/95 22:38:30 0.32E+05    60525 1111
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000s100302l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          60525     37435              0     23090         0         0
 Writing events file
  37435 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         60525     37435              0     23090         0         0
   in    4871.43 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100302l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad63007000s100302l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad63007000s100302l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :        37435
 
    copy bad pix array...
cleaning chip #           0
 Hot pixels & counts                   :              44        9287
 Flickering pixels iter, pixels & cnts :   1          13         185
cleaning chip #           1
 Hot pixels & counts                   :              42        9228
 Flickering pixels iter, pixels & cnts :   1          18         210
cleaning chip #           2
 Hot pixels & counts                   :              42        8996
 Flickering pixels iter, pixels & cnts :   1          13         191
cleaning chip #           3
 Hot pixels & counts                   :              38        8523
 Flickering pixels iter, pixels & cnts :   1          13         200
 
 Number of pixels rejected           :          223
 Number of (internal) image counts   :        37435
 Number of image cts rejected (N, %) :        36820     98.3571548
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :            57           60           55           51
 
 Image counts      :          9600         9603         9345         8887
 Image cts rejected:          9472         9438         9187         8723
 Image cts rej (%) :         98.67        98.28        98.31        98.15
 
    filtering data...
 
 Total counts      :          9600         9603         9345         8887
 Total cts rejected:          9472         9438         9187         8723
 Total cts rej (%) :         98.67        98.28        98.31        98.15
 
 Number of clean counts accepted  :          615
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :          223
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad63007000s100402h.unf
-> Extracting ad63007000s100402h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT   HIGH     30/07/95 08:48:10 0.12E+04    13865 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s100402h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100402h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad63007000s100402h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000s100412h.unf
-> Extracting ad63007000s100412h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 M31      BRIGHT2  HIGH     30/07/95 08:48:10 0.12E+04    14324 0110
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000s100412h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000s100412h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   16.000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad63007000s100412h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000g200170h.unf
-> Extracting ad63007000g200170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          99435        12              0     99423         0         0
 Writing events file
     12 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         99435        12              0     99423         0         0
   in      26.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.60E+05    99435      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          99435       139              0     99296         0         0
 Writing events file
    139 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         99435       139              0     99296         0         0
   in     216.55 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g200270m.unf
-> Extracting ad63007000g200270m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          80521      9672              0     70849         0         0
 Writing events file
   9672 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         80521      9672              0     70849         0         0
   in   11475.15 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200270m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200270m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    80521      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          80521      3298              0     77223         0         0
 Writing events file
   3298 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         80521      3298              0     77223         0         0
   in    4428.50 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200270m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g200370l.unf
-> Extracting ad63007000g200370l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          19133      2079              0     17054         0         0
 Writing events file
   2079 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         19133      2079              0     17054         0         0
   in    2940.68 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200370l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200370l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    19133      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          19133     16019              0      3114         0         0
 Writing events file
  16019 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         19133     16019              0      3114         0         0
   in   22882.79 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200370l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g200470h.unf
-> Extracting ad63007000g200470h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200470h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200470h.drk since it contains 0 events
-> Extracting ad63007000g200470h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1508      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g200470h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200470h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200470h.brt since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000g200570l.unf
-> Extracting ad63007000g200570l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1422      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g200570l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200570l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad63007000g200570l.drk since it contains 0 events
-> Extracting ad63007000g200570l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1422      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200570l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1422      1421              0         1         0         0
 Writing events file
   1421 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1422      1421              0         1         0         0
   in    2046.89 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200570l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g200670m.unf
-> Extracting ad63007000g200670m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      782      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            782        64              0       718         0         0
 Writing events file
     64 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           782        64              0       718         0         0
   in      80.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200670m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad63007000g200670m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      782      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g200670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            782        45              0       737         0         0
 Writing events file
     45 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           782        45              0       737         0         0
   in      79.63 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g200670m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g300170h.unf
-> Extracting ad63007000g300170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102159        18              0    102141         0         0
 Writing events file
     18 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        102159        18              0    102141         0         0
   in      26.21 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     30/07/95 02:43:02 0.62E+05   102159      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
         102159       130              0    102029         0         0
 Writing events file
    130 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
        102159       130              0    102029         0         0
   in     216.55 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g300270m.unf
-> Extracting ad63007000g300270m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          78760      8737              0     70023         0         0
 Writing events file
   8737 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         78760      8737              0     70023         0         0
   in   11475.15 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300270m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300270m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 22:35:18 0.56E+05    78760      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300270m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          78760      2977              0     75783         0         0
 Writing events file
   2977 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         78760      2977              0     75783         0         0
   in    4428.50 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300270m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g300370l.unf
-> Extracting ad63007000g300370l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          17963      1927              0     16036         0         0
 Writing events file
   1927 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17963      1927              0     16036         0         0
   in    2940.68 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300370l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300370l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      29/07/95 22:38:46 0.27E+05    17963      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300370l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
          17963     15029              0      2934         0         0
 Writing events file
  15029 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         17963     15029              0      2934         0         0
   in   22882.79 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300370l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g300470h.unf
-> Extracting ad63007000g300470h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300470h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300470h.drk since it contains 0 events
-> Extracting ad63007000g300470h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       HIGH     31/07/95 01:32:54 0.98E+03     1558      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g300470h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300470h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.48828E-03
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300470h.brt since it contains 0 events
-> Extracting bright and dark Earth events from ad63007000g300570l.unf
-> Extracting ad63007000g300570l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1329      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data19/seq_proc/63007000.004/ad63007000g300570l.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300570l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad63007000g300570l.drk since it contains 0 events
-> Extracting ad63007000g300570l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       LOW      30/07/95 03:25:42 0.20E+04     1329      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300570l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           1329      1328              0         1         0         0
 Writing events file
   1328 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1329      1328              0         1         0         0
   in    2046.89 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300570l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.15625E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad63007000g300670m.unf
-> Extracting ad63007000g300670m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      850      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            850        58              0       792         0         0
 Writing events file
     58 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           850        58              0       792         0         0
   in      80.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300670m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad63007000g300670m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 M31      PH       MEDIUM   29/07/95 23:27:18 0.61E+03      850      256
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data19/seq_proc/63007000.004/ad63007000g300670m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
            850        56              0       794         0         0
 Writing events file
     56 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           850        56              0       794         0         0
   in      79.63 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data19/seq_proc/63007000.004/
Setting mkf directory to /data/data19/seq_proc/63007000.004/
 
!earthevents:ASCA > read events ad63007000g300670m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0    255
 
Got the minimum time resolution of the read data:  0.39062E-02
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data19/seq_proc/63007000.004/
HK Directory is: /data/data19/seq_proc/63007000.004/
 
There is no RISETIME information in your files.
You cannot use GISCLEAN.
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

Determining information about this observation ( 18:25:49 )

-> Calculating ISAS time for sis
-> Calculating ISAS time for gis
-> Recording dates of PI calibration files
-> Standard Output From FTOOL sec2time:
 Offset of  1.500000000000000E+08 from 1/1/93     0:0:0
 is date and time (including leapseconds) = 3/10/97    2:39:56.000000
 Modified Julian Day    =   50724.111064814816928

Generating event file information page ( 18:30:20 )

-> Summing time and events for s0 event files
-> Standard Output From STOOL get_uniq_keys:
ad63007000s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000302h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad63007000s000402h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000102h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000302h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000402h.unf|S0_LVDL1|197|S0 event discrimination lower level for ccd 1
-> listing ad63007000s000102h.unf
-> listing ad63007000s000302h.unf
-> listing ad63007000s000402h.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s000202m.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000602m.unf|S0_ARENA|1|S0 Area discrimination enable/disable
-> listing ad63007000s000202m.unf
-> listing ad63007000s000602m.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s000502l.unf|S0_AEANL|0|S0 AE analog status
ad63007000s000702l.unf|S0_AEANL|0|S0 AE analog status
ad63007000s000802l.unf|S0_AEANL|1|S0 AE analog status
ad63007000s000502l.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000702l.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad63007000s000802l.unf|S0_ARENA|0|S0 Area discrimination enable/disable
-> listing ad63007000s000502l.unf
-> listing ad63007000s000702l.unf
-> listing ad63007000s000802l.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000312h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad63007000s000412h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000112h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000312h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000412h.unf|S0_LVDL1|197|S0 event discrimination lower level for ccd 1
-> listing ad63007000s000112h.unf
-> listing ad63007000s000312h.unf
-> listing ad63007000s000412h.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000301h.unf|S0_ARENA|1|S0 Area discrimination enable/disable
ad63007000s000401h.unf|S0_ARENA|0|S0 Area discrimination enable/disable
ad63007000s000101h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000301h.unf|S0_LVDL1|196|S0 event discrimination lower level for ccd 1
ad63007000s000401h.unf|S0_LVDL1|197|S0 event discrimination lower level for ccd 1
-> listing ad63007000s000101h.unf
-> listing ad63007000s000301h.unf
-> listing ad63007000s000401h.unf
-> Summing time and events for s1 event files
-> Standard Output From STOOL get_uniq_keys:
ad63007000s100102h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100402h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100102h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100402h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100102h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order
ad63007000s100402h.unf|S1CCDLST|2 2 2 1|S1 CCD readout order
-> listing ad63007000s100102h.unf
-> listing ad63007000s100402h.unf
-> listing ad63007000s100202m.unf
-> listing ad63007000s100302l.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s100112h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100412h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100112h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100412h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100112h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order
ad63007000s100412h.unf|S1CCDLST|2 2 2 1|S1 CCD readout order
-> listing ad63007000s100112h.unf
-> listing ad63007000s100412h.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000s100101h.unf|S1CCDPOW|1111|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100401h.unf|S1CCDPOW|0110|Which S1 CCDs are in use(0123): 0=OFF 1=ON
ad63007000s100101h.unf|S1CCDMOD|4|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100401h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4
ad63007000s100101h.unf|S1CCDLST|2 3 0 1|S1 CCD readout order
ad63007000s100401h.unf|S1CCDLST|2 2 2 1|S1 CCD readout order
-> listing ad63007000s100101h.unf
-> listing ad63007000s100401h.unf
-> Summing time and events for g2 event files
-> Standard Output From STOOL get_uniq_keys:
ad63007000g200170h.unf|CPU2|RUN|CPU2 run/stop
ad63007000g200470h.unf|CPU2|STOP|CPU2 run/stop
ad63007000g200170h.unf|CPU3|RUN|CPU3 run/stop
ad63007000g200470h.unf|CPU3|STOP|CPU3 run/stop
-> listing ad63007000g200170h.unf
-> listing ad63007000g200470h.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000g200270m.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255)
ad63007000g200670m.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255)
ad63007000g200270m.unf|SP_B_P|0|Spread discri B for POW2 method (0-255)
ad63007000g200670m.unf|SP_B_P|255|Spread discri B for POW2 method (0-255)
ad63007000g200270m.unf|SP_C_P|0|Spread discri C for POW2 method (0-255)
ad63007000g200670m.unf|SP_C_P|255|Spread discri C for POW2 method (0-255)
ad63007000g200270m.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255)
ad63007000g200670m.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255)
ad63007000g200270m.unf|SP_A_U_F|239|Spread discri A_U for FLF method (0-255)
ad63007000g200670m.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255)
ad63007000g200270m.unf|SP_B_F|226|Spread discri B for FLF method (0-255)
ad63007000g200670m.unf|SP_B_F|120|Spread discri B for FLF method (0-255)
ad63007000g200270m.unf|SP_C_F|0|Spread discri C for FLF method (0-255)
ad63007000g200670m.unf|SP_C_F|120|Spread discri C for FLF method (0-255)
ad63007000g200270m.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023)
ad63007000g200670m.unf|SP_PH_F|31098|Spread discri PH for FLF method (0-1023)
-> listing ad63007000g200270m.unf
-> listing ad63007000g200670m.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000g200370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255)
ad63007000g200570l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255)
ad63007000g200370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255)
ad63007000g200570l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255)
ad63007000g200370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255)
ad63007000g200570l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255)
ad63007000g200370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255)
ad63007000g200570l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255)
ad63007000g200370l.unf|SP_A_U_F|239|Spread discri A_U for FLF method (0-255)
ad63007000g200570l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255)
ad63007000g200370l.unf|SP_B_F|226|Spread discri B for FLF method (0-255)
ad63007000g200570l.unf|SP_B_F|120|Spread discri B for FLF method (0-255)
ad63007000g200370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255)
ad63007000g200570l.unf|SP_C_F|120|Spread discri C for FLF method (0-255)
ad63007000g200370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023)
ad63007000g200570l.unf|SP_PH_F|31098|Spread discri PH for FLF method (0-1023)
-> listing ad63007000g200370l.unf
-> listing ad63007000g200570l.unf
-> Summing time and events for g3 event files
-> Standard Output From STOOL get_uniq_keys:
ad63007000g300170h.unf|CPU2|RUN|CPU2 run/stop
ad63007000g300470h.unf|CPU2|STOP|CPU2 run/stop
ad63007000g300170h.unf|CPU3|RUN|CPU3 run/stop
ad63007000g300470h.unf|CPU3|STOP|CPU3 run/stop
-> listing ad63007000g300170h.unf
-> listing ad63007000g300470h.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000g300270m.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255)
ad63007000g300670m.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255)
ad63007000g300270m.unf|SP_B_P|0|Spread discri B for POW2 method (0-255)
ad63007000g300670m.unf|SP_B_P|255|Spread discri B for POW2 method (0-255)
ad63007000g300270m.unf|SP_C_P|0|Spread discri C for POW2 method (0-255)
ad63007000g300670m.unf|SP_C_P|255|Spread discri C for POW2 method (0-255)
ad63007000g300270m.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255)
ad63007000g300670m.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255)
ad63007000g300270m.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255)
ad63007000g300670m.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255)
ad63007000g300270m.unf|SP_B_F|224|Spread discri B for FLF method (0-255)
ad63007000g300670m.unf|SP_B_F|120|Spread discri B for FLF method (0-255)
ad63007000g300270m.unf|SP_C_F|0|Spread discri C for FLF method (0-255)
ad63007000g300670m.unf|SP_C_F|120|Spread discri C for FLF method (0-255)
ad63007000g300270m.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023)
ad63007000g300670m.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)
-> listing ad63007000g300270m.unf
-> listing ad63007000g300670m.unf
-> Standard Output From STOOL get_uniq_keys:
ad63007000g300370l.unf|SP_A_L_P|0|Spread discri A_L for POW2 method (0-255)
ad63007000g300570l.unf|SP_A_L_P|255|Spread discri A_L for POW2 method (0-255)
ad63007000g300370l.unf|SP_B_P|0|Spread discri B for POW2 method (0-255)
ad63007000g300570l.unf|SP_B_P|255|Spread discri B for POW2 method (0-255)
ad63007000g300370l.unf|SP_C_P|0|Spread discri C for POW2 method (0-255)
ad63007000g300570l.unf|SP_C_P|255|Spread discri C for POW2 method (0-255)
ad63007000g300370l.unf|SP_A_L_F|80|Spread discri A_L for FLF method (0-255)
ad63007000g300570l.unf|SP_A_L_F|0|Spread discri A_L for FLF method (0-255)
ad63007000g300370l.unf|SP_A_U_F|232|Spread discri A_U for FLF method (0-255)
ad63007000g300570l.unf|SP_A_U_F|0|Spread discri A_U for FLF method (0-255)
ad63007000g300370l.unf|SP_B_F|224|Spread discri B for FLF method (0-255)
ad63007000g300570l.unf|SP_B_F|120|Spread discri B for FLF method (0-255)
ad63007000g300370l.unf|SP_C_F|0|Spread discri C for FLF method (0-255)
ad63007000g300570l.unf|SP_C_F|120|Spread discri C for FLF method (0-255)
ad63007000g300370l.unf|SP_PH_F|0|Spread discri PH for FLF method (0-1023)
ad63007000g300570l.unf|SP_PH_F|31353|Spread discri PH for FLF method (0-1023)
-> listing ad63007000g300370l.unf
-> listing ad63007000g300570l.unf

Creating sequence documentation ( 18:53:32 )

Creating HTML source list ( 18:54:49 )

Listing the files for distribution ( 19:04:29 )

-> Saving job.par as ad63007000_004_job.par and process.par as ad63007000_004_process.par
-> Creating the FITS format file catalog ad63007000_tape.cat
-> Creating the trend product catalog
-> Creating the FITS format file catalog ad63007000_trend.cat
-> Creating ad63007000_004_file_info.html

Doing final wrap up of all files ( 19:40:14 )

-> Adding FITS keywords to all distributed FITS files
-> Running fverify on all distributed files
-> Calculating checksums for all FITS files
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Doing inventory of all files

Processing complete ( 21:52:35 )