The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 155665066.611300 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-12-07 16:17:42.61129 Modified Julian Day = 50789.678965408566000-> leapsec.fits already present in current directory
Offset of 155709336.476900 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-12-08 04:35:32.47690 Modified Julian Day = 50790.191348112268315-> Observation begins 155665066.6113 1997-12-07 16:17:42
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 155665066.611100 155709336.476900
Data file start and stop ascatime : 155665066.611100 155709336.476900
Aspecting run start and stop ascatime : 155665066.611220 155709336.476791
Time interval averaged over (seconds) : 44269.865571
Total pointing and manuver time (sec) : 29213.470703 15056.479492
Mean boresight Euler angles : 181.487005 46.924677 338.119854
RA DEC SUN ANGLE
Mean solar position (deg) : 253.56 -22.58
Mean aberration (arcsec) : -7.43 -11.86
Mean sat X-axis (deg) : 151.030550 -42.674957 83.51
Mean sat Y-axis (deg) : 256.149497 -15.796202 7.21
Mean sat Z-axis (deg) : 181.487005 43.075322 93.13
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 181.874298 43.103828 247.855865 0.145620
Minimum 181.695251 43.101601 247.822464 0.008340
Maximum 181.896866 43.248035 248.163544 11.662987
Sigma (RMS) 0.001384 0.001144 0.017646 0.724680
Number of ASPECT records processed = 26322
Aspecting to RA/DEC : 181.87429810 43.10382843
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 155676410.07671 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 181.874 DEC: 43.104
START TIME: SC 155665066.6112 = UT 1997-12-07 16:17:46
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000098 11.340 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
987.997070 11.595 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
1451.995850 9.275 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1515.995605 6.917 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1579.995361 4.937 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1659.995117 3.205 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1739.994873 2.136 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1883.994385 1.136 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
3027.990967 0.119 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
3035.990967 0.157 188443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 3
6683.979492 0.172 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
8779.973633 0.072 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
18155.945312 0.158 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
20251.939453 0.088 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
23899.927734 0.136 C08A83 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 0
26011.921875 0.079 188443 1 1 0 0 0 0 1 0 0 0 1 0 0 0 0 0 3
29643.910156 0.116 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
31771.904297 0.064 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
35631.890625 0.072 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
37483.886719 0.081 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
41123.875000 0.077 8A03 1 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0
43227.867188 0.125 8403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
44266.367188 0.394 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
44268.367188 1.736 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
44269.367188 2.917 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
44269.867188 3.628 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 26322
Attitude Steps: 26
Maneuver ACM time: 15056.5 sec
Pointed ACM time: 29213.5 sec
-> Calculating aspect point100 99 count=100 sum1=18130.9 sum2=4678.38 sum3=33839.8 100 100 count=2 sum1=362.614 sum2=93.58 sum3=676.855 101 100 count=1 sum1=181.319 sum2=46.791 sum3=338.371 103 102 count=1 sum1=181.341 sum2=46.813 sum3=338.33 104 103 count=1 sum1=181.349 sum2=46.82 sum3=338.316 107 105 count=2 sum1=362.763 sum2=93.691 sum3=676.528 110 107 count=1 sum1=181.408 sum2=46.867 sum3=338.223 110 108 count=1 sum1=181.415 sum2=46.871 sum3=338.214 111 108 count=1 sum1=181.42 sum2=46.876 sum3=338.205 112 109 count=1 sum1=181.436 sum2=46.887 sum3=338.183 113 110 count=3 sum1=544.329 sum2=140.678 sum3=1014.52 114 110 count=2 sum1=362.903 sum2=93.797 sum3=676.326 114 111 count=1 sum1=181.455 sum2=46.901 sum3=338.158 115 111 count=6 sum1=1088.77 sum2=281.44 sum3=2028.88 116 112 count=12 sum1=2177.67 sum2=562.971 sum3=4057.62 117 112 count=16 sum1=2903.68 sum2=750.689 sum3=5410.01 117 113 count=11032 sum1=2.00215e+06 sum2=517677 sum3=3.73015e+06 118 110 count=1 sum1=181.494 sum2=46.896 sum3=338.104 118 111 count=2 sum1=362.979 sum2=93.814 sum3=676.222 118 113 count=15133 sum1=2.74647e+06 sum2=710119 sum3=5.11674e+06 119 108 count=1 sum1=181.504 sum2=46.878 sum3=338.094 119 109 count=1 sum1=181.499 sum2=46.887 sum3=338.099 120 107 count=1 sum1=181.509 sum2=46.866 sum3=338.088 0 out of 26322 points outside bin structure-> Euler angles: 181.487, 46.9251, 338.119
Interpolating 2 records in time interval 155666470.607 - 155666518.607 Interpolating 3 records in time interval 155666534.607 - 155666582.607 Interpolating 2 records in time interval 155666598.607 - 155666646.607 Interpolating 1 records in time interval 155666678.606 - 155666726.606
607.998 second gap between superframes 10 and 11 Dropping SF 1955 with synch code word 1 = 245 not 243 Dropping SF 1956 with inconsistent datamode 0/3 Dropping SF 1957 with synch code word 1 = 240 not 243 Dropping SF 1958 with synch code word 0 = 226 not 250 Dropping SF 1959 with synch code word 1 = 194 not 243 Dropping SF 1960 with inconsistent datamode 0/31 Dropping SF 1961 with corrupted frame indicator Dropping SF 1962 with inconsistent datamode 0/31 Dropping SF 1963 with synch code word 1 = 51 not 243 Dropping SF 1964 with inconsistent datamode 0/24 Dropping SF 1965 with synch code word 0 = 202 not 250 Dropping SF 1966 with inconsistent datamode 0/31 Dropping SF 1967 with corrupted frame indicator Dropping SF 1968 with synch code word 0 = 154 not 250 Dropping SF 1969 with synch code word 0 = 60 not 250 Dropping SF 1970 with inconsistent datamode 0/31 Dropping SF 1971 with synch code word 1 = 51 not 243 Dropping SF 1972 with synch code word 0 = 226 not 250 Dropping SF 1973 with synch code word 1 = 240 not 243 Dropping SF 1974 with synch code word 0 = 249 not 250 Dropping SF 1975 with synch code word 1 = 235 not 243 Dropping SF 1976 with synch code word 1 = 245 not 243 Dropping SF 1977 with synch code word 1 = 240 not 243 Dropping SF 1978 with inconsistent datamode 12/0 Dropping SF 1979 with synch code word 2 = 16 not 32 Dropping SF 1980 with synch code word 0 = 60 not 250 Dropping SF 1981 with synch code word 1 = 235 not 243 Dropping SF 1982 with corrupted frame indicator Dropping SF 1983 with inconsistent datamode 0/31 Dropping SF 1984 with inconsistent datamode 0/12 Dropping SF 1985 with synch code word 0 = 252 not 250 Dropping SF 1986 with inconsistent datamode 0/31 Dropping SF 1987 with synch code word 0 = 154 not 250 Dropping SF 1988 with synch code word 2 = 64 not 32 Dropping SF 1989 with corrupted frame indicator Dropping SF 1990 with synch code word 0 = 202 not 250 Dropping SF 1991 with synch code word 0 = 154 not 250 Dropping SF 1992 with synch code word 0 = 226 not 250 Dropping SF 1993 with corrupted frame indicator Dropping SF 1994 with corrupted frame indicator Dropping SF 1995 with corrupted frame indicator Dropping SF 1996 with synch code word 1 = 147 not 243 Dropping SF 1997 with inconsistent datamode 0/16 Dropping SF 1998 with synch code word 1 = 255 not 243 Dropping SF 1999 with synch code word 1 = 242 not 243 Dropping SF 2000 with synch code word 1 = 147 not 243 Dropping SF 2001 with inconsistent datamode 0/6 Dropping SF 2002 with synch code word 1 = 219 not 243 Dropping SF 2003 with corrupted frame indicator Dropping SF 2004 with synch code word 1 = 240 not 243 Dropping SF 2005 with synch code word 2 = 16 not 32 Dropping SF 2006 with synch code word 0 = 154 not 250 Dropping SF 2007 with synch code word 1 = 147 not 243 Dropping SF 2008 with inconsistent datamode 0/12 Dropping SF 2009 with synch code word 1 = 255 not 243 Dropping SF 2010 with inconsistent datamode 0/31 Dropping SF 2011 with synch code word 0 = 252 not 250 Dropping SF 2012 with synch code word 0 = 246 not 250 Dropping SF 2013 with synch code word 2 = 35 not 32 Dropping SF 2014 with corrupted frame indicator Dropping SF 2015 with synch code word 1 = 240 not 243 Dropping SF 2016 with synch code word 1 = 147 not 243 Dropping SF 2017 with synch code word 0 = 202 not 250 Dropping SF 2018 with synch code word 1 = 240 not 243 Dropping SF 2019 with invalid bit rate 7 Dropping SF 2020 with synch code word 2 = 44 not 32 Dropping SF 2021 with synch code word 0 = 202 not 250 Dropping SF 2022 with corrupted frame indicator Dropping SF 2023 with synch code word 0 = 122 not 250 Dropping SF 2024 with synch code word 2 = 56 not 32 Dropping SF 2025 with synch code word 0 = 226 not 250 Dropping SF 2026 with synch code word 2 = 16 not 32 Dropping SF 2027 with synch code word 1 = 195 not 243 Dropping SF 2028 with synch code word 0 = 58 not 250 Dropping SF 2029 with synch code word 1 = 235 not 243 Dropping SF 2030 with synch code word 0 = 202 not 250 Dropping SF 2031 with corrupted frame indicator Dropping SF 2032 with corrupted frame indicator Dropping SF 2033 with corrupted frame indicator Dropping SF 2034 with synch code word 0 = 202 not 250 Dropping SF 2035 with invalid bit rate 7 Dropping SF 2036 with synch code word 2 = 35 not 32 Dropping SF 2037 with synch code word 1 = 195 not 243 Dropping SF 2038 with inconsistent datamode 0/31 Dropping SF 2039 with synch code word 1 = 147 not 243 Dropping SF 2040 with synch code word 1 = 147 not 243 Dropping SF 2041 with synch code word 0 = 202 not 250 Dropping SF 2042 with synch code word 2 = 16 not 32 Dropping SF 2043 with synch code word 2 = 16 not 32 Dropping SF 2044 with synch code word 1 = 147 not 243 Dropping SF 2045 with inconsistent datamode 0/31 Dropping SF 2046 with synch code word 2 = 16 not 32 Dropping SF 2047 with synch code word 1 = 147 not 243 Dropping SF 2048 with synch code word 1 = 240 not 243 Dropping SF 2049 with corrupted frame indicator Dropping SF 2050 with synch code word 1 = 147 not 243 Dropping SF 2051 with synch code word 0 = 58 not 250 Dropping SF 2052 with synch code word 2 = 16 not 32 Dropping SF 2053 with synch code word 0 = 226 not 250 Dropping SF 2054 with synch code word 2 = 64 not 32 Dropping SF 2055 with synch code word 0 = 154 not 250 Dropping SF 2056 with synch code word 2 = 35 not 32 Dropping SF 2057 with corrupted frame indicator Dropping SF 2058 with corrupted frame indicator Dropping SF 2059 with synch code word 0 = 154 not 250 Dropping SF 2060 with synch code word 0 = 226 not 250 Dropping SF 2061 with synch code word 1 = 195 not 243 Dropping SF 2062 with synch code word 1 = 242 not 243 Dropping SF 2063 with synch code word 2 = 64 not 32 Dropping SF 2064 with inconsistent datamode 0/31 Dropping SF 2065 with synch code word 2 = 38 not 32 Dropping SF 2066 with synch code word 1 = 147 not 243 Dropping SF 2067 with synch code word 1 = 51 not 243 Dropping SF 2068 with corrupted frame indicator Dropping SF 2069 with synch code word 0 = 251 not 250 Dropping SF 2070 with corrupted frame indicator Dropping SF 2071 with synch code word 0 = 202 not 250 Dropping SF 2072 with synch code word 0 = 154 not 250 Dropping SF 2073 with synch code word 0 = 154 not 250 Dropping SF 2074 with inconsistent CCD ID 3/2 Dropping SF 2075 with synch code word 1 = 51 not 243 Dropping SF 2076 with synch code word 2 = 38 not 32 Dropping SF 2077 with synch code word 0 = 202 not 250 Dropping SF 2078 with synch code word 2 = 64 not 32 Dropping SF 2079 with synch code word 1 = 51 not 243 Dropping SF 2080 with synch code word 1 = 147 not 243 SIS0 coordinate error time=155680772.43843 x=0 y=0 pha[0]=96 chip=0 SIS0 peak error time=155680800.43838 x=169 y=251 ph0=2353 ph4=3426 Dropping SF 2083 with synch code word 1 = 195 not 243 Dropping SF 2084 with synch code word 1 = 195 not 243 Dropping SF 2085 with inconsistent CCD ID 1/0 Dropping SF 2086 with synch code word 1 = 235 not 243 Dropping SF 2087 with synch code word 1 = 147 not 243 Dropping SF 2088 with synch code word 0 = 226 not 250 Dropping SF 2089 with synch code word 1 = 195 not 243 Dropping SF 2090 with synch code word 1 = 242 not 243 Dropping SF 2091 with synch code word 2 = 16 not 32 Dropping SF 2092 with synch code word 1 = 147 not 243 Dropping SF 2093 with inconsistent CCD ID 1/0 Dropping SF 2094 with synch code word 1 = 195 not 243 Dropping SF 2095 with synch code word 0 = 154 not 250 Dropping SF 2096 with inconsistent CCD ID 0/3 Dropping SF 2097 with inconsistent datamode 0/3 595.998 second gap between superframes 3851 and 3852 29.9999 second gap between superframes 5097 and 5098 Warning: GIS2 bit assignment changed between 155704896.49036 and 155704898.49035 Warning: GIS3 bit assignment changed between 155704910.49031 and 155704912.49031 Warning: GIS2 bit assignment changed between 155704918.49029 and 155704920.49028 Warning: GIS3 bit assignment changed between 155704928.49026 and 155704930.49025 Dropping SF 5424 with inconsistent datamode 0/31 Dropping SF 5426 with inconsistent datamode 0/31 6588 of 6731 super frames processed-> Removing the following files with NEVENTS=0
ft971207_1617_0435G201770L.fits[0] ft971207_1617_0435G201870M.fits[0] ft971207_1617_0435G202370L.fits[0] ft971207_1617_0435G202470M.fits[0] ft971207_1617_0435G202570M.fits[0] ft971207_1617_0435G202670M.fits[0] ft971207_1617_0435G202770M.fits[0] ft971207_1617_0435G203370L.fits[0] ft971207_1617_0435G203470M.fits[0] ft971207_1617_0435G203570M.fits[0] ft971207_1617_0435G203670M.fits[0] ft971207_1617_0435G203770M.fits[0] ft971207_1617_0435G204270M.fits[0] ft971207_1617_0435G204370H.fits[0] ft971207_1617_0435G205070H.fits[0] ft971207_1617_0435G205170H.fits[0] ft971207_1617_0435G205270H.fits[0] ft971207_1617_0435G205370H.fits[0] ft971207_1617_0435G205470H.fits[0] ft971207_1617_0435G205770H.fits[0] ft971207_1617_0435G205870H.fits[0] ft971207_1617_0435G205970L.fits[0] ft971207_1617_0435G206070H.fits[0] ft971207_1617_0435G301770L.fits[0] ft971207_1617_0435G301870M.fits[0] ft971207_1617_0435G302370L.fits[0] ft971207_1617_0435G302470M.fits[0] ft971207_1617_0435G302570M.fits[0] ft971207_1617_0435G302670M.fits[0] ft971207_1617_0435G302770M.fits[0] ft971207_1617_0435G303370L.fits[0] ft971207_1617_0435G303470M.fits[0] ft971207_1617_0435G303570M.fits[0] ft971207_1617_0435G303670M.fits[0] ft971207_1617_0435G303770M.fits[0] ft971207_1617_0435G304170H.fits[0] ft971207_1617_0435G304270M.fits[0] ft971207_1617_0435G304370H.fits[0] ft971207_1617_0435G304470H.fits[0] ft971207_1617_0435G305070H.fits[0] ft971207_1617_0435G305370H.fits[0] ft971207_1617_0435G305470H.fits[0] ft971207_1617_0435G305570H.fits[0] ft971207_1617_0435G305670H.fits[0] ft971207_1617_0435G305770H.fits[0] ft971207_1617_0435G305970H.fits[0] ft971207_1617_0435G306070H.fits[0] ft971207_1617_0435G306170L.fits[0] ft971207_1617_0435G306270H.fits[0] ft971207_1617_0435S002101L.fits[0] ft971207_1617_0435S002601M.fits[0] ft971207_1617_0435S102101L.fits[0] ft971207_1617_0435S102601M.fits[0]-> Checking for empty GTI extensions
ft971207_1617_0435S000101M.fits[2] ft971207_1617_0435S000201L.fits[2] ft971207_1617_0435S000301M.fits[2] ft971207_1617_0435S000401H.fits[2] ft971207_1617_0435S000501M.fits[2] ft971207_1617_0435S000601L.fits[2] ft971207_1617_0435S000701M.fits[2] ft971207_1617_0435S000801M.fits[2] ft971207_1617_0435S000901M.fits[2] ft971207_1617_0435S001001H.fits[2] ft971207_1617_0435S001101M.fits[2] ft971207_1617_0435S001201L.fits[2] ft971207_1617_0435S001301M.fits[2] ft971207_1617_0435S001401L.fits[2] ft971207_1617_0435S001501L.fits[2] ft971207_1617_0435S001601L.fits[2] ft971207_1617_0435S001701M.fits[2] ft971207_1617_0435S001801H.fits[2] ft971207_1617_0435S001901M.fits[2] ft971207_1617_0435S002001L.fits[2] ft971207_1617_0435S002201L.fits[2] ft971207_1617_0435S002301M.fits[2] ft971207_1617_0435S002401H.fits[2] ft971207_1617_0435S002501M.fits[2] ft971207_1617_0435S002701M.fits[2] ft971207_1617_0435S002801H.fits[2] ft971207_1617_0435S002901H.fits[2] ft971207_1617_0435S003001L.fits[2] ft971207_1617_0435S003101L.fits[2] ft971207_1617_0435S003201H.fits[2]-> Merging GTIs from the following files:
ft971207_1617_0435S100101M.fits[2] ft971207_1617_0435S100201L.fits[2] ft971207_1617_0435S100301M.fits[2] ft971207_1617_0435S100401H.fits[2] ft971207_1617_0435S100501M.fits[2] ft971207_1617_0435S100601L.fits[2] ft971207_1617_0435S100701M.fits[2] ft971207_1617_0435S100801M.fits[2] ft971207_1617_0435S100901M.fits[2] ft971207_1617_0435S101001H.fits[2] ft971207_1617_0435S101101M.fits[2] ft971207_1617_0435S101201L.fits[2] ft971207_1617_0435S101301M.fits[2] ft971207_1617_0435S101401L.fits[2] ft971207_1617_0435S101501L.fits[2] ft971207_1617_0435S101601L.fits[2] ft971207_1617_0435S101701M.fits[2] ft971207_1617_0435S101801H.fits[2] ft971207_1617_0435S101901M.fits[2] ft971207_1617_0435S102001L.fits[2] ft971207_1617_0435S102201L.fits[2] ft971207_1617_0435S102301M.fits[2] ft971207_1617_0435S102401H.fits[2] ft971207_1617_0435S102501M.fits[2] ft971207_1617_0435S102701M.fits[2] ft971207_1617_0435S102801H.fits[2] ft971207_1617_0435S102901H.fits[2] ft971207_1617_0435S103001L.fits[2] ft971207_1617_0435S103101L.fits[2] ft971207_1617_0435S103201H.fits[2]-> Merging GTIs from the following files:
ft971207_1617_0435G200170M.fits[2] ft971207_1617_0435G200270L.fits[2] ft971207_1617_0435G200370L.fits[2] ft971207_1617_0435G200470M.fits[2] ft971207_1617_0435G200570M.fits[2] ft971207_1617_0435G200670M.fits[2] ft971207_1617_0435G200770M.fits[2] ft971207_1617_0435G200870H.fits[2] ft971207_1617_0435G200970M.fits[2] ft971207_1617_0435G201070L.fits[2] ft971207_1617_0435G201170M.fits[2] ft971207_1617_0435G201270H.fits[2] ft971207_1617_0435G201370M.fits[2] ft971207_1617_0435G201470L.fits[2] ft971207_1617_0435G201570L.fits[2] ft971207_1617_0435G201670L.fits[2] ft971207_1617_0435G201970M.fits[2] ft971207_1617_0435G202070M.fits[2] ft971207_1617_0435G202170L.fits[2] ft971207_1617_0435G202270L.fits[2] ft971207_1617_0435G202870M.fits[2] ft971207_1617_0435G202970M.fits[2] ft971207_1617_0435G203070H.fits[2] ft971207_1617_0435G203170M.fits[2] ft971207_1617_0435G203270L.fits[2] ft971207_1617_0435G203870M.fits[2] ft971207_1617_0435G203970M.fits[2] ft971207_1617_0435G204070H.fits[2] ft971207_1617_0435G204170H.fits[2] ft971207_1617_0435G204470H.fits[2] ft971207_1617_0435G204570H.fits[2] ft971207_1617_0435G204670H.fits[2] ft971207_1617_0435G204770H.fits[2] ft971207_1617_0435G204870H.fits[2] ft971207_1617_0435G204970H.fits[2] ft971207_1617_0435G205570H.fits[2] ft971207_1617_0435G205670H.fits[2]-> Merging GTIs from the following files:
ft971207_1617_0435G300170M.fits[2] ft971207_1617_0435G300270L.fits[2] ft971207_1617_0435G300370L.fits[2] ft971207_1617_0435G300470M.fits[2] ft971207_1617_0435G300570M.fits[2] ft971207_1617_0435G300670M.fits[2] ft971207_1617_0435G300770M.fits[2] ft971207_1617_0435G300870H.fits[2] ft971207_1617_0435G300970M.fits[2] ft971207_1617_0435G301070L.fits[2] ft971207_1617_0435G301170M.fits[2] ft971207_1617_0435G301270H.fits[2] ft971207_1617_0435G301370M.fits[2] ft971207_1617_0435G301470L.fits[2] ft971207_1617_0435G301570L.fits[2] ft971207_1617_0435G301670L.fits[2] ft971207_1617_0435G301970M.fits[2] ft971207_1617_0435G302070M.fits[2] ft971207_1617_0435G302170L.fits[2] ft971207_1617_0435G302270L.fits[2] ft971207_1617_0435G302870M.fits[2] ft971207_1617_0435G302970M.fits[2] ft971207_1617_0435G303070H.fits[2] ft971207_1617_0435G303170M.fits[2] ft971207_1617_0435G303270L.fits[2] ft971207_1617_0435G303870M.fits[2] ft971207_1617_0435G303970M.fits[2] ft971207_1617_0435G304070H.fits[2] ft971207_1617_0435G304570H.fits[2] ft971207_1617_0435G304670H.fits[2] ft971207_1617_0435G304770H.fits[2] ft971207_1617_0435G304870H.fits[2] ft971207_1617_0435G304970H.fits[2] ft971207_1617_0435G305170H.fits[2] ft971207_1617_0435G305270H.fits[2] ft971207_1617_0435G305870H.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200570h.prelist merge count = 8 photon cnt = 6463 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200270l.prelist merge count = 5 photon cnt = 2626 GISSORTSPLIT:LO:g200370l.prelist merge count = 3 photon cnt = 215 GISSORTSPLIT:LO:g200170m.prelist merge count = 3 photon cnt = 43 GISSORTSPLIT:LO:g200270m.prelist merge count = 9 photon cnt = 13623 GISSORTSPLIT:LO:g200370m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:Total filenames split = 37 GISSORTSPLIT:LO:Total split file cnt = 14 GISSORTSPLIT:LO:End program-> Creating ad65014000g200170m.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G200170M.fits 2 -- ft971207_1617_0435G200770M.fits 3 -- ft971207_1617_0435G200970M.fits 4 -- ft971207_1617_0435G201170M.fits 5 -- ft971207_1617_0435G201370M.fits 6 -- ft971207_1617_0435G202070M.fits 7 -- ft971207_1617_0435G202970M.fits 8 -- ft971207_1617_0435G203170M.fits 9 -- ft971207_1617_0435G203970M.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G200170M.fits 2 -- ft971207_1617_0435G200770M.fits 3 -- ft971207_1617_0435G200970M.fits 4 -- ft971207_1617_0435G201170M.fits 5 -- ft971207_1617_0435G201370M.fits 6 -- ft971207_1617_0435G202070M.fits 7 -- ft971207_1617_0435G202970M.fits 8 -- ft971207_1617_0435G203170M.fits 9 -- ft971207_1617_0435G203970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000g200270h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G200870H.fits 2 -- ft971207_1617_0435G201270H.fits 3 -- ft971207_1617_0435G203070H.fits 4 -- ft971207_1617_0435G204070H.fits 5 -- ft971207_1617_0435G204770H.fits 6 -- ft971207_1617_0435G204870H.fits 7 -- ft971207_1617_0435G204970H.fits 8 -- ft971207_1617_0435G205670H.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G200870H.fits 2 -- ft971207_1617_0435G201270H.fits 3 -- ft971207_1617_0435G203070H.fits 4 -- ft971207_1617_0435G204070H.fits 5 -- ft971207_1617_0435G204770H.fits 6 -- ft971207_1617_0435G204870H.fits 7 -- ft971207_1617_0435G204970H.fits 8 -- ft971207_1617_0435G205670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000g200370l.unf
---- cmerge: version 1.6 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G200370L.fits 2 -- ft971207_1617_0435G201070L.fits 3 -- ft971207_1617_0435G201570L.fits 4 -- ft971207_1617_0435G202270L.fits 5 -- ft971207_1617_0435G203270L.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G200370L.fits 2 -- ft971207_1617_0435G201070L.fits 3 -- ft971207_1617_0435G201570L.fits 4 -- ft971207_1617_0435G202270L.fits 5 -- ft971207_1617_0435G203270L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000215 events
ft971207_1617_0435G200270L.fits ft971207_1617_0435G201470L.fits ft971207_1617_0435G202170L.fits-> Ignoring the following files containing 000000043 events
ft971207_1617_0435G201970M.fits ft971207_1617_0435G202870M.fits ft971207_1617_0435G203870M.fits-> Ignoring the following files containing 000000010 events
ft971207_1617_0435G200570M.fits-> Ignoring the following files containing 000000010 events
ft971207_1617_0435G200470M.fits-> Ignoring the following files containing 000000008 events
ft971207_1617_0435G200670M.fits-> Ignoring the following files containing 000000007 events
ft971207_1617_0435G201670L.fits-> Ignoring the following files containing 000000005 events
ft971207_1617_0435G205570H.fits-> Ignoring the following files containing 000000002 events
ft971207_1617_0435G204670H.fits-> Ignoring the following files containing 000000001 events
ft971207_1617_0435G204570H.fits-> Ignoring the following files containing 000000001 events
ft971207_1617_0435G204470H.fits-> Ignoring the following files containing 000000001 events
ft971207_1617_0435G204170H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 8 photon cnt = 6012 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300270l.prelist merge count = 5 photon cnt = 2417 GISSORTSPLIT:LO:g300370l.prelist merge count = 3 photon cnt = 184 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 39 GISSORTSPLIT:LO:g300270m.prelist merge count = 9 photon cnt = 12595 GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:Total filenames split = 36 GISSORTSPLIT:LO:Total split file cnt = 13 GISSORTSPLIT:LO:End program-> Creating ad65014000g300170m.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G300170M.fits 2 -- ft971207_1617_0435G300770M.fits 3 -- ft971207_1617_0435G300970M.fits 4 -- ft971207_1617_0435G301170M.fits 5 -- ft971207_1617_0435G301370M.fits 6 -- ft971207_1617_0435G302070M.fits 7 -- ft971207_1617_0435G302970M.fits 8 -- ft971207_1617_0435G303170M.fits 9 -- ft971207_1617_0435G303970M.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G300170M.fits 2 -- ft971207_1617_0435G300770M.fits 3 -- ft971207_1617_0435G300970M.fits 4 -- ft971207_1617_0435G301170M.fits 5 -- ft971207_1617_0435G301370M.fits 6 -- ft971207_1617_0435G302070M.fits 7 -- ft971207_1617_0435G302970M.fits 8 -- ft971207_1617_0435G303170M.fits 9 -- ft971207_1617_0435G303970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000g300270h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G300870H.fits 2 -- ft971207_1617_0435G301270H.fits 3 -- ft971207_1617_0435G303070H.fits 4 -- ft971207_1617_0435G304070H.fits 5 -- ft971207_1617_0435G304770H.fits 6 -- ft971207_1617_0435G304870H.fits 7 -- ft971207_1617_0435G304970H.fits 8 -- ft971207_1617_0435G305870H.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G300870H.fits 2 -- ft971207_1617_0435G301270H.fits 3 -- ft971207_1617_0435G303070H.fits 4 -- ft971207_1617_0435G304070H.fits 5 -- ft971207_1617_0435G304770H.fits 6 -- ft971207_1617_0435G304870H.fits 7 -- ft971207_1617_0435G304970H.fits 8 -- ft971207_1617_0435G305870H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000g300370l.unf
---- cmerge: version 1.6 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435G300370L.fits 2 -- ft971207_1617_0435G301070L.fits 3 -- ft971207_1617_0435G301570L.fits 4 -- ft971207_1617_0435G302270L.fits 5 -- ft971207_1617_0435G303270L.fits Merging binary extension #: 2 1 -- ft971207_1617_0435G300370L.fits 2 -- ft971207_1617_0435G301070L.fits 3 -- ft971207_1617_0435G301570L.fits 4 -- ft971207_1617_0435G302270L.fits 5 -- ft971207_1617_0435G303270L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000184 events
ft971207_1617_0435G300270L.fits ft971207_1617_0435G301470L.fits ft971207_1617_0435G302170L.fits-> Ignoring the following files containing 000000039 events
ft971207_1617_0435G301970M.fits ft971207_1617_0435G302870M.fits ft971207_1617_0435G303870M.fits-> Ignoring the following files containing 000000011 events
ft971207_1617_0435G301670L.fits-> Ignoring the following files containing 000000010 events
ft971207_1617_0435G300570M.fits-> Ignoring the following files containing 000000006 events
ft971207_1617_0435G305170H.fits-> Ignoring the following files containing 000000006 events
ft971207_1617_0435G300470M.fits-> Ignoring the following files containing 000000006 events
ft971207_1617_0435G300670M.fits-> Ignoring the following files containing 000000005 events
ft971207_1617_0435G304570H.fits-> Ignoring the following files containing 000000001 events
ft971207_1617_0435G305270H.fits-> Ignoring the following files containing 000000001 events
ft971207_1617_0435G304670H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 6 photon cnt = 27435 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 175 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 8 photon cnt = 8879 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 2 photon cnt = 94 SIS0SORTSPLIT:LO:s000501m.prelist merge count = 12 photon cnt = 29741 SIS0SORTSPLIT:LO:s000601m.prelist merge count = 1 photon cnt = 13 SIS0SORTSPLIT:LO:Total filenames split = 30 SIS0SORTSPLIT:LO:Total split file cnt = 6 SIS0SORTSPLIT:LO:End program-> Creating ad65014000s000101m.unf
---- cmerge: version 1.6 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S000101M.fits 2 -- ft971207_1617_0435S000301M.fits 3 -- ft971207_1617_0435S000501M.fits 4 -- ft971207_1617_0435S000701M.fits 5 -- ft971207_1617_0435S000901M.fits 6 -- ft971207_1617_0435S001101M.fits 7 -- ft971207_1617_0435S001301M.fits 8 -- ft971207_1617_0435S001701M.fits 9 -- ft971207_1617_0435S001901M.fits 10 -- ft971207_1617_0435S002301M.fits 11 -- ft971207_1617_0435S002501M.fits 12 -- ft971207_1617_0435S002701M.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S000101M.fits 2 -- ft971207_1617_0435S000301M.fits 3 -- ft971207_1617_0435S000501M.fits 4 -- ft971207_1617_0435S000701M.fits 5 -- ft971207_1617_0435S000901M.fits 6 -- ft971207_1617_0435S001101M.fits 7 -- ft971207_1617_0435S001301M.fits 8 -- ft971207_1617_0435S001701M.fits 9 -- ft971207_1617_0435S001901M.fits 10 -- ft971207_1617_0435S002301M.fits 11 -- ft971207_1617_0435S002501M.fits 12 -- ft971207_1617_0435S002701M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000s000201h.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S000401H.fits 2 -- ft971207_1617_0435S001001H.fits 3 -- ft971207_1617_0435S001801H.fits 4 -- ft971207_1617_0435S002401H.fits 5 -- ft971207_1617_0435S002801H.fits 6 -- ft971207_1617_0435S003201H.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S000401H.fits 2 -- ft971207_1617_0435S001001H.fits 3 -- ft971207_1617_0435S001801H.fits 4 -- ft971207_1617_0435S002401H.fits 5 -- ft971207_1617_0435S002801H.fits 6 -- ft971207_1617_0435S003201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000s000301l.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S000201L.fits 2 -- ft971207_1617_0435S000601L.fits 3 -- ft971207_1617_0435S001201L.fits 4 -- ft971207_1617_0435S001401L.fits 5 -- ft971207_1617_0435S001601L.fits 6 -- ft971207_1617_0435S002001L.fits 7 -- ft971207_1617_0435S002201L.fits 8 -- ft971207_1617_0435S003101L.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S000201L.fits 2 -- ft971207_1617_0435S000601L.fits 3 -- ft971207_1617_0435S001201L.fits 4 -- ft971207_1617_0435S001401L.fits 5 -- ft971207_1617_0435S001601L.fits 6 -- ft971207_1617_0435S002001L.fits 7 -- ft971207_1617_0435S002201L.fits 8 -- ft971207_1617_0435S003101L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000175 events
ft971207_1617_0435S002901H.fits-> Ignoring the following files containing 000000094 events
ft971207_1617_0435S001501L.fits ft971207_1617_0435S003001L.fits-> Ignoring the following files containing 000000013 events
ft971207_1617_0435S000801M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 6 photon cnt = 37592 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 199 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 8 photon cnt = 11759 SIS1SORTSPLIT:LO:s100401l.prelist merge count = 2 photon cnt = 105 SIS1SORTSPLIT:LO:s100501m.prelist merge count = 12 photon cnt = 40859 SIS1SORTSPLIT:LO:s100601m.prelist merge count = 1 photon cnt = 7 SIS1SORTSPLIT:LO:Total filenames split = 30 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad65014000s100101m.unf
---- cmerge: version 1.6 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S100101M.fits 2 -- ft971207_1617_0435S100301M.fits 3 -- ft971207_1617_0435S100501M.fits 4 -- ft971207_1617_0435S100701M.fits 5 -- ft971207_1617_0435S100901M.fits 6 -- ft971207_1617_0435S101101M.fits 7 -- ft971207_1617_0435S101301M.fits 8 -- ft971207_1617_0435S101701M.fits 9 -- ft971207_1617_0435S101901M.fits 10 -- ft971207_1617_0435S102301M.fits 11 -- ft971207_1617_0435S102501M.fits 12 -- ft971207_1617_0435S102701M.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S100101M.fits 2 -- ft971207_1617_0435S100301M.fits 3 -- ft971207_1617_0435S100501M.fits 4 -- ft971207_1617_0435S100701M.fits 5 -- ft971207_1617_0435S100901M.fits 6 -- ft971207_1617_0435S101101M.fits 7 -- ft971207_1617_0435S101301M.fits 8 -- ft971207_1617_0435S101701M.fits 9 -- ft971207_1617_0435S101901M.fits 10 -- ft971207_1617_0435S102301M.fits 11 -- ft971207_1617_0435S102501M.fits 12 -- ft971207_1617_0435S102701M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000s100201h.unf
---- cmerge: version 1.6 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S100401H.fits 2 -- ft971207_1617_0435S101001H.fits 3 -- ft971207_1617_0435S101801H.fits 4 -- ft971207_1617_0435S102401H.fits 5 -- ft971207_1617_0435S102801H.fits 6 -- ft971207_1617_0435S103201H.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S100401H.fits 2 -- ft971207_1617_0435S101001H.fits 3 -- ft971207_1617_0435S101801H.fits 4 -- ft971207_1617_0435S102401H.fits 5 -- ft971207_1617_0435S102801H.fits 6 -- ft971207_1617_0435S103201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad65014000s100301l.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft971207_1617_0435S100201L.fits 2 -- ft971207_1617_0435S100601L.fits 3 -- ft971207_1617_0435S101201L.fits 4 -- ft971207_1617_0435S101401L.fits 5 -- ft971207_1617_0435S101601L.fits 6 -- ft971207_1617_0435S102001L.fits 7 -- ft971207_1617_0435S102201L.fits 8 -- ft971207_1617_0435S103101L.fits Merging binary extension #: 2 1 -- ft971207_1617_0435S100201L.fits 2 -- ft971207_1617_0435S100601L.fits 3 -- ft971207_1617_0435S101201L.fits 4 -- ft971207_1617_0435S101401L.fits 5 -- ft971207_1617_0435S101601L.fits 6 -- ft971207_1617_0435S102001L.fits 7 -- ft971207_1617_0435S102201L.fits 8 -- ft971207_1617_0435S103101L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000199 events
ft971207_1617_0435S102901H.fits-> Ignoring the following files containing 000000105 events
ft971207_1617_0435S101501L.fits ft971207_1617_0435S103001L.fits-> Ignoring the following files containing 000000007 events
ft971207_1617_0435S100801M.fits-> Tar-ing together the leftover raw files
a ft971207_1617_0435G200270L.fits 31K a ft971207_1617_0435G200470M.fits 31K a ft971207_1617_0435G200570M.fits 31K a ft971207_1617_0435G200670M.fits 31K a ft971207_1617_0435G201470L.fits 31K a ft971207_1617_0435G201670L.fits 31K a ft971207_1617_0435G201970M.fits 31K a ft971207_1617_0435G202170L.fits 31K a ft971207_1617_0435G202870M.fits 31K a ft971207_1617_0435G203870M.fits 31K a ft971207_1617_0435G204170H.fits 31K a ft971207_1617_0435G204470H.fits 31K a ft971207_1617_0435G204570H.fits 31K a ft971207_1617_0435G204670H.fits 31K a ft971207_1617_0435G205570H.fits 31K a ft971207_1617_0435G300270L.fits 31K a ft971207_1617_0435G300470M.fits 31K a ft971207_1617_0435G300570M.fits 31K a ft971207_1617_0435G300670M.fits 31K a ft971207_1617_0435G301470L.fits 31K a ft971207_1617_0435G301670L.fits 31K a ft971207_1617_0435G301970M.fits 31K a ft971207_1617_0435G302170L.fits 31K a ft971207_1617_0435G302870M.fits 31K a ft971207_1617_0435G303870M.fits 31K a ft971207_1617_0435G304570H.fits 31K a ft971207_1617_0435G304670H.fits 31K a ft971207_1617_0435G305170H.fits 31K a ft971207_1617_0435G305270H.fits 31K a ft971207_1617_0435S000801M.fits 29K a ft971207_1617_0435S001501L.fits 29K a ft971207_1617_0435S002901H.fits 34K a ft971207_1617_0435S003001L.fits 29K a ft971207_1617_0435S100801M.fits 29K a ft971207_1617_0435S101501L.fits 29K a ft971207_1617_0435S102901H.fits 34K a ft971207_1617_0435S103001L.fits 31K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft971207_1617.0435' is successfully opened Data Start Time is 155665064.61 (19971207 161740) Time Margin 2.0 sec included Sync error detected in 1954 th SF Sync error detected in 1955 th SF Sync error detected in 1956 th SF Sync error detected in 1957 th SF Sync error detected in 1958 th SF Sync error detected in 1959 th SF Sync error detected in 1960 th SF Sync error detected in 1961 th SF Sync error detected in 1962 th SF Sync error detected in 1963 th SF Sync error detected in 1964 th SF Sync error detected in 1965 th SF Sync error detected in 1966 th SF Sync error detected in 1967 th SF Sync error detected in 1968 th SF Sync error detected in 1969 th SF Sync error detected in 1970 th SF Sync error detected in 1971 th SF Sync error detected in 1972 th SF Sync error detected in 1973 th SF Sync error detected in 1974 th SF Sync error detected in 1975 th SF Sync error detected in 1976 th SF Sync error detected in 1977 th SF Sync error detected in 1978 th SF Sync error detected in 1979 th SF Sync error detected in 1980 th SF Sync error detected in 1981 th SF Sync error detected in 1982 th SF Sync error detected in 1983 th SF Sync error detected in 1984 th SF Sync error detected in 1985 th SF Sync error detected in 1986 th SF Sync error detected in 1987 th SF Sync error detected in 1989 th SF Sync error detected in 1990 th SF Sync error detected in 1991 th SF Sync error detected in 1994 th SF Sync error detected in 1995 th SF Sync error detected in 1997 th SF Sync error detected in 1998 th SF Sync error detected in 1999 th SF Sync error detected in 2000 th SF Sync error detected in 2001 th SF Sync error detected in 2002 th SF Sync error detected in 2003 th SF 'ft971207_1617.0435' EOF detected, sf=6731 Data End Time is 155709338.48 (19971208 043534) Gain History is written in ft971207_1617_0435.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft971207_1617_0435.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft971207_1617_0435.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft971207_1617_0435CMHK.fits
The sum of the selected column is 24360.000 The mean of the selected column is 101.92469 The standard deviation of the selected column is 1.5912634 The minimum of selected column is 99.000000 The maximum of selected column is 109.00000 The number of points used in calculation is 239-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24036.000 The mean of the selected column is 101.84746 The standard deviation of the selected column is 1.4417904 The minimum of selected column is 99.000000 The maximum of selected column is 106.00000 The number of points used in calculation is 236
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000g200270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000g300170m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000g300270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000101m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000102m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000112m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000201h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000202h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000212h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s000312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100101m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100102m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100112m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100201h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100202h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100212h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad65014000s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 155676410.07671 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:
S0-HK file: ft971207_1617_0435S0HK.fits
S1-HK file: ft971207_1617_0435S1HK.fits
G2-HK file: ft971207_1617_0435G2HK.fits
G3-HK file: ft971207_1617_0435G3HK.fits
Date and time are: 1997-12-07 16:17:14 mjd=50789.678641
Orbit file name is ./frf.orbit.241
Epoch of Orbital Elements: 1997-12-01 12:59:59
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa971207_1617.0435
output FITS File: ft971207_1617_0435.mkf
mkfilter2: Warning, faQparam error: time= 1.556649866113e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 1.556650186113e+08 outside range of attitude file
Euler angles undefined for this bin
Total 1387 Data bins were processed.
-> Checking if column TIME in ft971207_1617_0435.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 4372.8050 The mean of the selected column is 21.023101 The standard deviation of the selected column is 9.3160823 The minimum of selected column is 5.5000167 The maximum of selected column is 61.812687 The number of points used in calculation is 208-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<48.9 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad65014000s000112m.unf into ad65014000s000112m.evt
The sum of the selected column is 4372.8050 The mean of the selected column is 21.023101 The standard deviation of the selected column is 9.3160823 The minimum of selected column is 5.5000167 The maximum of selected column is 61.812687 The number of points used in calculation is 208-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<48.9 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad65014000s000201h.unf because of mode
The sum of the selected column is 4168.2586 The mean of the selected column is 18.691743 The standard deviation of the selected column is 8.2663410 The minimum of selected column is 2.1875067 The maximum of selected column is 48.093895 The number of points used in calculation is 223-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<43.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad65014000s000212h.unf into ad65014000s000212h.evt
The sum of the selected column is 4168.2586 The mean of the selected column is 18.691743 The standard deviation of the selected column is 8.2663410 The minimum of selected column is 2.1875067 The maximum of selected column is 48.093895 The number of points used in calculation is 223-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<43.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad65014000s000301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad65014000s000302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad65014000s000312l.evt since it contains 0 events
The sum of the selected column is 7283.2826 The mean of the selected column is 35.355741 The standard deviation of the selected column is 14.146073 The minimum of selected column is 11.218784 The maximum of selected column is 110.53159 The number of points used in calculation is 206-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<77.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad65014000s100112m.unf into ad65014000s100112m.evt
The sum of the selected column is 7283.2826 The mean of the selected column is 35.355741 The standard deviation of the selected column is 14.146073 The minimum of selected column is 11.218784 The maximum of selected column is 110.53159 The number of points used in calculation is 206-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<77.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad65014000s100201h.unf because of mode
The sum of the selected column is 7019.4109 The mean of the selected column is 31.477179 The standard deviation of the selected column is 12.902236 The minimum of selected column is 1.9583392 The maximum of selected column is 74.281479 The number of points used in calculation is 223-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<70.1 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad65014000s100212h.unf into ad65014000s100212h.evt
The sum of the selected column is 7019.4109 The mean of the selected column is 31.477179 The standard deviation of the selected column is 12.902236 The minimum of selected column is 1.9583392 The maximum of selected column is 74.281479 The number of points used in calculation is 223-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<70.1 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad65014000s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad65014000s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad65014000s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad65014000g200270h.unf into ad65014000g200270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad65014000g200370l.unf into ad65014000g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Deleting ad65014000g200370l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad65014000g300270h.unf into ad65014000g300270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad65014000g300370l.unf into ad65014000g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Deleting ad65014000g300370l.evt since it contains 0 events
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad65014000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8414
Mean RA/DEC/ROLL : 181.8528 43.0802 247.8414
Pnt RA/DEC/ROLL : 181.7159 43.2584 247.8414
Image rebin factor : 1
Attitude Records : 26331
GTI intervals : 19
Total GTI (secs) : 9056.065
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1131.99 1131.99
20 Percent Complete: Total/live time: 2016.00 2016.00
30 Percent Complete: Total/live time: 3839.93 3839.93
40 Percent Complete: Total/live time: 3839.93 3839.93
50 Percent Complete: Total/live time: 6047.99 6047.99
60 Percent Complete: Total/live time: 6047.99 6047.99
70 Percent Complete: Total/live time: 6528.07 6528.07
80 Percent Complete: Total/live time: 9056.07 9056.07
100 Percent Complete: Total/live time: 9056.07 9056.07
Number of attitude steps used: 23
Number of attitude steps avail: 9756
Mean RA/DEC pixel offset: -12.3308 -3.7474
writing expo file: ad65014000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000g200170m.evt
ASCAEXPO_V0.9b
reading data file: ad65014000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8404
Mean RA/DEC/ROLL : 181.8505 43.0826 247.8404
Pnt RA/DEC/ROLL : 181.8942 43.1224 247.8404
Image rebin factor : 1
Attitude Records : 26331
GTI intervals : 10
Total GTI (secs) : 7460.136
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1440.00 1440.00
20 Percent Complete: Total/live time: 2782.49 2782.49
30 Percent Complete: Total/live time: 2782.49 2782.49
40 Percent Complete: Total/live time: 3136.02 3136.02
50 Percent Complete: Total/live time: 5024.02 5024.02
60 Percent Complete: Total/live time: 5024.02 5024.02
70 Percent Complete: Total/live time: 7460.14 7460.14
100 Percent Complete: Total/live time: 7460.14 7460.14
Number of attitude steps used: 10
Number of attitude steps avail: 15893
Mean RA/DEC pixel offset: -11.3368 -3.7136
writing expo file: ad65014000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000g200270h.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad65014000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8523
Mean RA/DEC/ROLL : 181.8691 43.1019 247.8523
Pnt RA/DEC/ROLL : 181.7001 43.2363 247.8523
Image rebin factor : 1
Attitude Records : 26331
GTI intervals : 19
Total GTI (secs) : 9056.065
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1131.99 1131.99
20 Percent Complete: Total/live time: 2016.00 2016.00
30 Percent Complete: Total/live time: 3839.93 3839.93
40 Percent Complete: Total/live time: 3839.93 3839.93
50 Percent Complete: Total/live time: 6047.99 6047.99
60 Percent Complete: Total/live time: 6047.99 6047.99
70 Percent Complete: Total/live time: 6528.07 6528.07
80 Percent Complete: Total/live time: 9056.07 9056.07
100 Percent Complete: Total/live time: 9056.07 9056.07
Number of attitude steps used: 23
Number of attitude steps avail: 9756
Mean RA/DEC pixel offset: -0.7773 -2.5996
writing expo file: ad65014000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000g300170m.evt
ASCAEXPO_V0.9b
reading data file: ad65014000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8513
Mean RA/DEC/ROLL : 181.8663 43.1046 247.8513
Pnt RA/DEC/ROLL : 181.8783 43.1004 247.8513
Image rebin factor : 1
Attitude Records : 26331
GTI intervals : 10
Total GTI (secs) : 7458.136
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1440.00 1440.00
20 Percent Complete: Total/live time: 2782.49 2782.49
30 Percent Complete: Total/live time: 2782.49 2782.49
40 Percent Complete: Total/live time: 3136.02 3136.02
50 Percent Complete: Total/live time: 5024.02 5024.02
60 Percent Complete: Total/live time: 5024.02 5024.02
70 Percent Complete: Total/live time: 7458.14 7458.14
100 Percent Complete: Total/live time: 7458.14 7458.14
Number of attitude steps used: 10
Number of attitude steps avail: 15893
Mean RA/DEC pixel offset: -0.4660 -2.6337
writing expo file: ad65014000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000g300270h.evt
ASCAEXPO_V0.9b
reading data file: ad65014000s000102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8336
Mean RA/DEC/ROLL : 181.8415 43.0969 247.8336
Pnt RA/DEC/ROLL : 181.7275 43.2416 247.8336
Image rebin factor : 4
Attitude Records : 26331
Hot Pixels : 3
GTI intervals : 28
Total GTI (secs) : 6632.167
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 808.14 808.14
20 Percent Complete: Total/live time: 1992.16 1992.16
30 Percent Complete: Total/live time: 2120.16 2120.16
40 Percent Complete: Total/live time: 4072.16 4072.16
50 Percent Complete: Total/live time: 4072.16 4072.16
60 Percent Complete: Total/live time: 4212.08 4212.08
70 Percent Complete: Total/live time: 4820.07 4820.07
80 Percent Complete: Total/live time: 6632.17 6632.17
100 Percent Complete: Total/live time: 6632.17 6632.17
Number of attitude steps used: 21
Number of attitude steps avail: 8693
Mean RA/DEC pixel offset: -59.9028 -95.1628
writing expo file: ad65014000s000102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000s000102m.evt
ASCAEXPO_V0.9b
reading data file: ad65014000s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8328
Mean RA/DEC/ROLL : 181.8396 43.0993 247.8328
Pnt RA/DEC/ROLL : 181.9054 43.1057 247.8328
Image rebin factor : 4
Attitude Records : 26331
Hot Pixels : 3
GTI intervals : 12
Total GTI (secs) : 7136.008
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1431.86 1431.86
20 Percent Complete: Total/live time: 2750.48 2750.48
30 Percent Complete: Total/live time: 2750.48 2750.48
40 Percent Complete: Total/live time: 3104.01 3104.01
50 Percent Complete: Total/live time: 4968.13 4968.13
60 Percent Complete: Total/live time: 4968.13 4968.13
70 Percent Complete: Total/live time: 5246.39 5246.39
80 Percent Complete: Total/live time: 7072.01 7072.01
90 Percent Complete: Total/live time: 7072.01 7072.01
100 Percent Complete: Total/live time: 7136.01 7136.01
Number of attitude steps used: 11
Number of attitude steps avail: 17407
Mean RA/DEC pixel offset: -72.7993 -97.8527
writing expo file: ad65014000s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000s000202h.evt
ASCAEXPO_V0.9b
reading data file: ad65014000s100102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8470
Mean RA/DEC/ROLL : 181.8613 43.0899 247.8470
Pnt RA/DEC/ROLL : 181.7077 43.2484 247.8470
Image rebin factor : 4
Attitude Records : 26331
Hot Pixels : 7
GTI intervals : 27
Total GTI (secs) : 6560.030
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 855.85 855.85
20 Percent Complete: Total/live time: 1984.02 1984.02
30 Percent Complete: Total/live time: 2112.02 2112.02
40 Percent Complete: Total/live time: 4064.02 4064.02
50 Percent Complete: Total/live time: 4064.02 4064.02
60 Percent Complete: Total/live time: 4171.94 4171.94
70 Percent Complete: Total/live time: 4811.93 4811.93
80 Percent Complete: Total/live time: 6560.03 6560.03
100 Percent Complete: Total/live time: 6560.03 6560.03
Number of attitude steps used: 21
Number of attitude steps avail: 8661
Mean RA/DEC pixel offset: -64.1477 -26.7475
writing expo file: ad65014000s100102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000s100102m.evt
ASCAEXPO_V0.9b
reading data file: ad65014000s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa971207_1617.0435
making an exposure map...
Aspect RA/DEC/ROLL : 181.8740 43.1034 247.8462
Mean RA/DEC/ROLL : 181.8591 43.0924 247.8462
Pnt RA/DEC/ROLL : 181.8858 43.1126 247.8462
Image rebin factor : 4
Attitude Records : 26331
Hot Pixels : 7
GTI intervals : 11
Total GTI (secs) : 7140.145
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1126.12 1126.12
20 Percent Complete: Total/live time: 1521.12 1521.12
30 Percent Complete: Total/live time: 3112.15 3112.15
40 Percent Complete: Total/live time: 3112.15 3112.15
50 Percent Complete: Total/live time: 5000.14 5000.14
60 Percent Complete: Total/live time: 5000.14 5000.14
70 Percent Complete: Total/live time: 7076.14 7076.14
80 Percent Complete: Total/live time: 7076.14 7076.14
90 Percent Complete: Total/live time: 7140.14 7140.14
100 Percent Complete: Total/live time: 7140.14 7140.14
Number of attitude steps used: 13
Number of attitude steps avail: 16534
Mean RA/DEC pixel offset: -76.7893 -28.4198
writing expo file: ad65014000s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad65014000s100202h.evtad65014000s000102m.expo ad65014000s000202h.expo ad65014000s100102m.expo ad65014000s100202h.expo-> Summing the following images to produce ad65014000sis32002_all.totsky
ad65014000s000102m.img ad65014000s000202h.img ad65014000s100102m.img ad65014000s100202h.img-> Summing the following images to produce ad65014000sis32002_lo.totsky
ad65014000s000102m_lo.img ad65014000s000202h_lo.img ad65014000s100102m_lo.img ad65014000s100202h_lo.img-> Summing the following images to produce ad65014000sis32002_hi.totsky
ad65014000s000102m_hi.img ad65014000s000202h_hi.img ad65014000s100102m_hi.img ad65014000s100202h_hi.img-> Running XIMAGE to create ad65014000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad65014000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 5.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 5 min: 0 ![2]XIMAGE> read/exp_map ad65014000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 457.806 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 457 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "NGC4111_N1" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 December 7, 1997 Exposure: 27468.3 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 152 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 17.0000 17 0 ![11]XIMAGE> exit-> Summing gis images
ad65014000g200170m.expo ad65014000g200270h.expo ad65014000g300170m.expo ad65014000g300270h.expo-> Summing the following images to produce ad65014000gis25670_all.totsky
ad65014000g200170m.img ad65014000g200270h.img ad65014000g300170m.img ad65014000g300270h.img-> Summing the following images to produce ad65014000gis25670_lo.totsky
ad65014000g200170m_lo.img ad65014000g200270h_lo.img ad65014000g300170m_lo.img ad65014000g300270h_lo.img-> Summing the following images to produce ad65014000gis25670_hi.totsky
ad65014000g200170m_hi.img ad65014000g200270h_hi.img ad65014000g300170m_hi.img ad65014000g300270h_hi.img-> Running XIMAGE to create ad65014000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad65014000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 7.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 7 min: 0 ![2]XIMAGE> read/exp_map ad65014000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 550.507 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 550 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "NGC4111_N1" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 December 7, 1997 Exposure: 33030.4 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 16546 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 24.0000 24 0 ![11]XIMAGE> exit
117 134 8.96144e-05 12 12 9.607 93 116 8.23484e-05 17 11 8.68196-> Smoothing ad65014000gis25670_hi.totsky with ad65014000gis25670.totexpo
117 134 8.11374e-05 13 11 15.1938 94 115 3.21287e-05 15 13 6.68121-> Smoothing ad65014000gis25670_lo.totsky with ad65014000gis25670.totexpo
95 115 4.26323e-05 78 13 9.97931-> Determining extraction radii
117 134 12 T 93 116 17 T-> Sources with radius >= 2
117 134 12 T 93 116 17 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad65014000gis25670.src
207 137 2.38209e-05 91 28 9.1906-> Smoothing ad65014000sis32002_hi.totsky with ad65014000sis32002.totexpo
209 134 1.68488e-05 88 23 14.6839-> Determining extraction radii
207 137 38 T-> Sources with radius >= 2
207 137 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad65014000sis32002.src
The sum of the selected column is 24732.000 The mean of the selected column is 449.67273 The standard deviation of the selected column is 17.793106 The minimum of selected column is 415.00000 The maximum of selected column is 487.00000 The number of points used in calculation is 55-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24992.000 The mean of the selected column is 454.40000 The standard deviation of the selected column is 15.122463 The minimum of selected column is 419.00000 The maximum of selected column is 489.00000 The number of points used in calculation is 55-> Converting (828.0,548.0,2.0) to s1 detector coordinates
The sum of the selected column is 453.00000 The mean of the selected column is 453.00000 The standard deviation of the selected column is undefined The minimum of selected column is 453.00000 The maximum of selected column is 453.00000 The number of points used in calculation is 1-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 487.00000 The mean of the selected column is 487.00000 The standard deviation of the selected column is undefined The minimum of selected column is 487.00000 The maximum of selected column is 487.00000 The number of points used in calculation is 1-> Converting (117.0,134.0,2.0) to g2 detector coordinates
The sum of the selected column is 2906.0000 The mean of the selected column is 132.09091 The standard deviation of the selected column is 1.1087999 The minimum of selected column is 130.00000 The maximum of selected column is 134.00000 The number of points used in calculation is 22-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2989.0000 The mean of the selected column is 135.86364 The standard deviation of the selected column is 1.2834275 The minimum of selected column is 134.00000 The maximum of selected column is 138.00000 The number of points used in calculation is 22-> Converting (93.0,116.0,2.0) to g2 detector coordinates
The sum of the selected column is 2487.0000 The mean of the selected column is 124.35000 The standard deviation of the selected column is 1.2258187 The minimum of selected column is 122.00000 The maximum of selected column is 127.00000 The number of points used in calculation is 20-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3301.0000 The mean of the selected column is 165.05000 The standard deviation of the selected column is 0.88704121 The minimum of selected column is 164.00000 The maximum of selected column is 166.00000 The number of points used in calculation is 20-> Converting (117.0,134.0,2.0) to g3 detector coordinates
The sum of the selected column is 3571.0000 The mean of the selected column is 137.34615 The standard deviation of the selected column is 0.79711017 The minimum of selected column is 136.00000 The maximum of selected column is 139.00000 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3553.0000 The mean of the selected column is 136.65385 The standard deviation of the selected column is 1.2310096 The minimum of selected column is 134.00000 The maximum of selected column is 139.00000 The number of points used in calculation is 26-> Converting (93.0,116.0,2.0) to g3 detector coordinates
The sum of the selected column is 2078.0000 The mean of the selected column is 129.87500 The standard deviation of the selected column is 1.2583057 The minimum of selected column is 128.00000 The maximum of selected column is 133.00000 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2653.0000 The mean of the selected column is 165.81250 The standard deviation of the selected column is 1.0468206 The minimum of selected column is 164.00000 The maximum of selected column is 167.00000 The number of points used in calculation is 16
1 ad65014000s000102m.evt 700 1 ad65014000s000202h.evt 700-> Fetching SIS0_NOTCHIP0.1
ad65014000s000102m.evt ad65014000s000202h.evt-> Deleting ad65014000s010102_1.pi since it has 380 events
1 ad65014000s000112m.evt 753 1 ad65014000s000212h.evt 753-> SIS0_NOTCHIP0.1 already present in current directory
ad65014000s000112m.evt ad65014000s000212h.evt-> Deleting ad65014000s010212_1.pi since it has 402 events
1 ad65014000s100102m.evt 675 1 ad65014000s100202h.evt 675-> Fetching SIS1_NOTCHIP0.1
ad65014000s100102m.evt ad65014000s100202h.evt-> Deleting ad65014000s110102_1.pi since it has 364 events
1 ad65014000s100112m.evt 696 1 ad65014000s100212h.evt 696-> SIS1_NOTCHIP0.1 already present in current directory
ad65014000s100112m.evt ad65014000s100212h.evt-> Deleting ad65014000s110212_1.pi since it has 379 events
1 ad65014000g200170m.evt 4591 1 ad65014000g200270h.evt 4591-> GIS2_REGION256.4 already present in current directory
ad65014000g200170m.evt ad65014000g200270h.evt-> Deleting ad65014000g210170_1.pi since it has 247 events
ad65014000g200170m.evt ad65014000g200270h.evt-> Deleting ad65014000g210170_2.pi since it has 332 events
1 ad65014000g300170m.evt 4682 1 ad65014000g300270h.evt 4682-> GIS3_REGION256.4 already present in current directory
ad65014000g300170m.evt ad65014000g300270h.evt-> Deleting ad65014000g310170_1.pi since it has 245 events
ad65014000g300170m.evt ad65014000g300270h.evt-> Deleting ad65014000g310170_2.pi since it has 366 events
ad65014000g200170m.evt[2] ad65014000g200270h.evt[2]-> Making L1 light curve of ft971207_1617_0435G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 13781 output records from 13791 good input G2_L1 records.-> Making L1 light curve of ft971207_1617_0435G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 14620 output records from 21959 good input G2_L1 records.-> Merging GTIs from the following files:
ad65014000g300170m.evt[2] ad65014000g300270h.evt[2]-> Making L1 light curve of ft971207_1617_0435G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 13240 output records from 13250 good input G3_L1 records.-> Making L1 light curve of ft971207_1617_0435G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 14411 output records from 21271 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 6731 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft971207_1617_0435.mkf
1 ad65014000g200170m.unf 22712 1 ad65014000g200270h.unf 22712 1 ad65014000g200370l.unf 22712-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 14:47:53 28-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad65014000g220170.cal
Net count rate (cts/s) for file 1 0.1407 +/- 2.2034E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.3807E+06 using 84 PHA bins.
Reduced chi-squared = 1.7931E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.3730E+06 using 84 PHA bins.
Reduced chi-squared = 1.7603E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.3730E+06 using 84 PHA bins.
Reduced chi-squared = 1.7380E+04
!XSPEC> renorm
Chi-Squared = 955.4 using 84 PHA bins.
Reduced chi-squared = 12.09
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
758.61 0 1.000 5.895 0.1073 4.0899E-02
3.7085E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
444.55 0 1.000 5.883 0.1554 5.5215E-02
3.3092E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
241.36 -1 1.000 5.951 0.1823 7.6475E-02
2.2230E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
204.75 -2 1.000 6.010 0.2027 9.0281E-02
1.2942E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
199.83 -3 1.000 5.987 0.1830 8.6729E-02
1.6399E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
199.31 -4 1.000 5.994 0.1857 8.7911E-02
1.5195E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
199.21 -5 1.000 5.992 0.1834 8.7495E-02
1.5606E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
199.21 -6 1.000 5.992 0.1838 8.7620E-02
1.5482E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.99234 +/- 0.93369E-02
3 3 2 gaussian/b Sigma 0.183756 +/- 0.10404E-01
4 4 2 gaussian/b norm 8.761976E-02 +/- 0.22443E-02
5 2 3 gaussian/b LineE 6.59759 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.192813 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.548176E-02 +/- 0.15721E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 199.2 using 84 PHA bins.
Reduced chi-squared = 2.522
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad65014000g220170.cal peaks at 5.99234 +/- 0.0093369 keV1 ad65014000g300170m.unf 21024 1 ad65014000g300270h.unf 21024 1 ad65014000g300370l.unf 21024-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 14:48:32 28-Dec-99
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad65014000g320170.cal
Net count rate (cts/s) for file 1 0.1265 +/- 2.0920E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.6438E+06 using 84 PHA bins.
Reduced chi-squared = 2.1349E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.6327E+06 using 84 PHA bins.
Reduced chi-squared = 2.0932E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.6327E+06 using 84 PHA bins.
Reduced chi-squared = 2.0667E+04
!XSPEC> renorm
Chi-Squared = 1187. using 84 PHA bins.
Reduced chi-squared = 15.03
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
952.57 0 1.000 5.893 9.4602E-02 3.6596E-02
3.1388E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
368.39 0 1.000 5.866 0.1413 5.7785E-02
2.6955E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
139.39 -1 1.000 5.912 0.1548 8.2382E-02
1.7379E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
127.28 -2 1.000 5.931 0.1614 8.8927E-02
1.3642E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.85 -3 1.000 5.926 0.1566 8.8294E-02
1.4287E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.83 -4 1.000 5.927 0.1568 8.8422E-02
1.4160E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.83 -5 1.000 5.927 0.1566 8.8396E-02
1.4186E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92695 +/- 0.78515E-02
3 3 2 gaussian/b Sigma 0.156631 +/- 0.96340E-02
4 4 2 gaussian/b norm 8.839627E-02 +/- 0.20986E-02
5 2 3 gaussian/b LineE 6.52560 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.164351 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.418576E-02 +/- 0.13300E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 126.8 using 84 PHA bins.
Reduced chi-squared = 1.605
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad65014000g320170.cal peaks at 5.92695 +/- 0.0078515 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000102m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 27
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 16
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 2
Number of (internal) image counts : 27
Number of image cts rejected (N, %) : 1659.26
By chip : 0 1 2 3
Pixels rejected : 0 2 0 0
Image counts : 0 27 0 0
Image cts rejected: 0 16 0 0
Image cts rej (%) : 0.00 59.26 0.00 0.00
filtering data...
Total counts : 0 27 0 0
Total cts rejected: 0 16 0 0
Total cts rej (%) : 0.00 59.26 0.00 0.00
Number of clean counts accepted : 11
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 2
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s000112m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000112m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 28
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 16
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 2
Number of (internal) image counts : 28
Number of image cts rejected (N, %) : 1657.14
By chip : 0 1 2 3
Pixels rejected : 0 2 0 0
Image counts : 0 28 0 0
Image cts rejected: 0 16 0 0
Image cts rej (%) : 0.00 57.14 0.00 0.00
filtering data...
Total counts : 0 28 0 0
Total cts rejected: 0 16 0 0
Total cts rej (%) : 0.00 57.14 0.00 0.00
Number of clean counts accepted : 12
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 2
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s000202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1451
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 3 896
Flickering pixels iter, pixels & cnts : 1 3 14
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 1451
Number of image cts rejected (N, %) : 91062.72
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 1451 0 0
Image cts rejected: 0 910 0 0
Image cts rej (%) : 0.00 62.72 0.00 0.00
filtering data...
Total counts : 0 1451 0 0
Total cts rejected: 0 910 0 0
Total cts rej (%) : 0.00 62.72 0.00 0.00
Number of clean counts accepted : 541
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s000212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1588
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 3 896
Flickering pixels iter, pixels & cnts : 1 3 14
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 1588
Number of image cts rejected (N, %) : 91057.30
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 1588 0 0
Image cts rejected: 0 910 0 0
Image cts rej (%) : 0.00 57.30 0.00 0.00
filtering data...
Total counts : 0 1588 0 0
Total cts rejected: 0 910 0 0
Total cts rej (%) : 0.00 57.30 0.00 0.00
Number of clean counts accepted : 678
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3209
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 2967
Flickering pixels iter, pixels & cnts : 1 1 7
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 3
Number of (internal) image counts : 3209
Number of image cts rejected (N, %) : 297492.68
By chip : 0 1 2 3
Pixels rejected : 0 3 0 0
Image counts : 0 3209 0 0
Image cts rejected: 0 2974 0 0
Image cts rej (%) : 0.00 92.68 0.00 0.00
filtering data...
Total counts : 0 3209 0 0
Total cts rejected: 0 2974 0 0
Total cts rej (%) : 0.00 92.68 0.00 0.00
Number of clean counts accepted : 235
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 3
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3262
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 2967
Flickering pixels iter, pixels & cnts : 1 1 7
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 3
Number of (internal) image counts : 3262
Number of image cts rejected (N, %) : 297491.17
By chip : 0 1 2 3
Pixels rejected : 0 3 0 0
Image counts : 0 3262 0 0
Image cts rejected: 0 2974 0 0
Image cts rej (%) : 0.00 91.17 0.00 0.00
filtering data...
Total counts : 0 3262 0 0
Total cts rejected: 0 2974 0 0
Total cts rej (%) : 0.00 91.17 0.00 0.00
Number of clean counts accepted : 288
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 3
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100102m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100102m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 43
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 5 30
Number of pixels rejected : 5
Number of (internal) image counts : 43
Number of image cts rejected (N, %) : 3069.77
By chip : 0 1 2 3
Pixels rejected : 0 0 0 5
Image counts : 0 0 0 43
Image cts rejected: 0 0 0 30
Image cts rej (%) : 0.00 0.00 0.00 69.77
filtering data...
Total counts : 0 0 0 43
Total cts rejected: 0 0 0 30
Total cts rej (%) : 0.00 0.00 0.00 69.77
Number of clean counts accepted : 13
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100112m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100112m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 43
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 5 30
Number of pixels rejected : 5
Number of (internal) image counts : 43
Number of image cts rejected (N, %) : 3069.77
By chip : 0 1 2 3
Pixels rejected : 0 0 0 5
Image counts : 0 0 0 43
Image cts rejected: 0 0 0 30
Image cts rej (%) : 0.00 0.00 0.00 69.77
filtering data...
Total counts : 0 0 0 43
Total cts rejected: 0 0 0 30
Total cts rej (%) : 0.00 0.00 0.00 69.77
Number of clean counts accepted : 13
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2305
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 8 1800
Flickering pixels iter, pixels & cnts : 1 4 26
Number of pixels rejected : 12
Number of (internal) image counts : 2305
Number of image cts rejected (N, %) : 182679.22
By chip : 0 1 2 3
Pixels rejected : 0 0 0 12
Image counts : 0 0 0 2305
Image cts rejected: 0 0 0 1826
Image cts rej (%) : 0.00 0.00 0.00 79.22
filtering data...
Total counts : 0 0 0 2305
Total cts rejected: 0 0 0 1826
Total cts rej (%) : 0.00 0.00 0.00 79.22
Number of clean counts accepted : 479
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 12
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2357
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 8 1801
Flickering pixels iter, pixels & cnts : 1 4 26
Number of pixels rejected : 12
Number of (internal) image counts : 2357
Number of image cts rejected (N, %) : 182777.51
By chip : 0 1 2 3
Pixels rejected : 0 0 0 12
Image counts : 0 0 0 2357
Image cts rejected: 0 0 0 1827
Image cts rej (%) : 0.00 0.00 0.00 77.51
filtering data...
Total counts : 0 0 0 2357
Total cts rejected: 0 0 0 1827
Total cts rej (%) : 0.00 0.00 0.00 77.51
Number of clean counts accepted : 530
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 12
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 5752
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 5565
Number of pixels rejected : 7
Number of (internal) image counts : 5752
Number of image cts rejected (N, %) : 556596.75
By chip : 0 1 2 3
Pixels rejected : 0 0 0 7
Image counts : 0 0 0 5752
Image cts rejected: 0 0 0 5565
Image cts rej (%) : 0.00 0.00 0.00 96.75
filtering data...
Total counts : 0 0 0 5752
Total cts rejected: 0 0 0 5565
Total cts rej (%) : 0.00 0.00 0.00 96.75
Number of clean counts accepted : 187
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad65014000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 5771
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 7 5565
Number of pixels rejected : 7
Number of (internal) image counts : 5771
Number of image cts rejected (N, %) : 556596.43
By chip : 0 1 2 3
Pixels rejected : 0 0 0 7
Image counts : 0 0 0 5771
Image cts rejected: 0 0 0 5565
Image cts rej (%) : 0.00 0.00 0.00 96.43
filtering data...
Total counts : 0 0 0 5771
Total cts rejected: 0 0 0 5565
Total cts rej (%) : 0.00 0.00 0.00 96.43
Number of clean counts accepted : 206
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad65014000g200170m.unfOffset of 213408004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-10-07 00:00:00.00000 Modified Julian Day = 51458.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
11 624 1955 622 1963 80 1987 128 1990 320 2011 208 2025 112 3852 612 3
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files