The following information is also available:
Time column is TIME ORDERED-> Fetching fa940201_0315.2340.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 34226160.621900 34299639.907400
Data file start and stop ascatime : 34226160.621900 34299639.907400
Aspecting run start and stop ascatime : 34226160.621987 34299639.907278
Time interval averaged over (seconds) : 73479.285291
Total pointing and manuver time (sec) : 46894.984375 26584.482422
Mean boresight Euler angles : 196.557914 113.639362 329.922480
RA DEC SUN ANGLE
Mean solar position (deg) : 313.90 -17.35
Mean aberration (arcsec) : 8.24 2.38
Mean sat X-axis (deg) : 71.861117 -52.441800 92.09
Mean sat Y-axis (deg) : 299.631902 -27.330126 16.52
Mean sat Z-axis (deg) : 196.557914 -23.639362 106.38
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 196.867996 -23.650511 240.047241 0.083770
Minimum 196.853668 -23.704544 240.014816 0.000000
Maximum 196.870758 -23.646215 240.077408 3.244925
Sigma (RMS) 0.000622 0.000516 0.002880 0.242404
Number of ASPECT records processed = 43390
Aspecting to RA/DEC : 196.86799622 -23.65051079
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 196.868 DEC: -23.651
START TIME: SC 34226160.6220 = UT 01/02/94 03:16:00
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500105 2.012 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
9.999992 3.051 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
424.998840 2.045 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
696.997986 2.055 1C2C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 4 3
2012.994141 1.034 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
2496.992676 0.034 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
2710.992188 0.000 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
6456.981445 0.237 1C2C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 4 3
8472.975586 0.103 E02283 1 1 0 0 0 0 0 1 0 1 0 0 0 1 0 0 4
12200.964844 0.141 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
14232.958984 0.066 E02283 1 1 0 0 0 0 0 1 0 1 0 0 0 1 0 0 4
17960.947266 0.019 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
19992.941406 0.037 C02283 1 1 0 0 0 0 0 1 0 1 0 0 0 1 0 0 0
23704.931641 0.011 182C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 0 3
25752.923828 0.032 C02283 1 1 0 0 0 0 0 1 0 1 0 0 0 1 0 0 0
29996.912109 0.053 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
31494.908203 0.092 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
35224.898438 0.028 1C2C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 4 3
37256.890625 0.061 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
40968.878906 0.044 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
43008.875000 0.075 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
46728.863281 0.040 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
48764.859375 0.061 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
52488.847656 0.018 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
54522.839844 0.014 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
58232.828125 0.032 1C2C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 4 3
60278.824219 0.011 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
63992.812500 0.067 102C43 1 1 0 0 0 0 1 0 0 0 1 1 0 1 0 0 2
66058.804688 0.060 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
69736.796875 0.075 2C03 1 1 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0
71792.789062 0.000 2203 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0
73479.289062 0.396 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
Attitude Records: 43390
Attitude Steps: 32
Maneuver ACM time: 26584.5 sec
Pointed ACM time: 46895.0 sec
-> Calculating aspect point99 99 count=134 sum1=26337 sum2=15231.9 sum3=44213.2 99 100 count=143 sum1=28106.2 sum2=16255.6 sum3=47181.1 99 101 count=20 sum1=3931.02 sum2=2273.64 sum3=6598.38 100 96 count=42694 sum1=8.39184e+06 sum2=4.8517e+06 sum3=1.40857e+07 100 97 count=54 sum1=10614.2 sum2=6136.89 sum3=17815.9 100 98 count=29 sum1=5700.25 sum2=3296.04 sum3=9567.91 100 99 count=200 sum1=39311.8 sum2=22733.2 sum3=65986.3 100 100 count=22 sum1=4324.15 sum2=2500.93 sum3=7258.31 100 101 count=54 sum1=10613.9 sum2=6139.03 sum3=17815.1 100 102 count=5 sum1=982.775 sum2=568.465 sum3=1649.45 101 99 count=34 sum1=6683.11 sum2=3864.59 sum3=11217.6 0 out of 43389 points outside bin structure-> Euler angles: 196.558, 113.639, 329.923
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft940201_0315.2340",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft940201_0315.2340 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 473824 Bright = 219680 Fast = 0 Frame = 0 Dark frame = 1152 Histogram = 0 Integration = 0 PH = 694656 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 10887 no. of SIS events found = 1068977-> Standard Error Output From FTOOL frfread
coordinate error 1 64-> Removing the following files with NEVENTS=0
ft940201_0315_2340G200570M.fits ft940201_0315_2340G201570M.fits ft940201_0315_2340G201699.fits ft940201_0315_2340G201770M.fits ft940201_0315_2340G202170M.fits ft940201_0315_2340G203470M.fits ft940201_0315_2340G203770H.fits ft940201_0315_2340G204470M.fits ft940201_0315_2340G204799.fits ft940201_0315_2340G205570M.fits ft940201_0315_2340G206570M.fits ft940201_0315_2340G206999.fits ft940201_0315_2340G207270H.fits ft940201_0315_2340G207370M.fits ft940201_0315_2340G207470M.fits ft940201_0315_2340G207570H.fits ft940201_0315_2340G207670H.fits ft940201_0315_2340G207770H.fits ft940201_0315_2340G207870H.fits ft940201_0315_2340G207970H.fits ft940201_0315_2340G208070H.fits ft940201_0315_2340G208399.fits ft940201_0315_2340G208570H.fits ft940201_0315_2340G208670H.fits ft940201_0315_2340G208770H.fits ft940201_0315_2340G208870H.fits ft940201_0315_2340G300570M.fits ft940201_0315_2340G300870H.fits ft940201_0315_2340G301570M.fits ft940201_0315_2340G301699.fits ft940201_0315_2340G301770M.fits ft940201_0315_2340G302170M.fits ft940201_0315_2340G303470M.fits ft940201_0315_2340G303870H.fits ft940201_0315_2340G304470M.fits ft940201_0315_2340G304799.fits ft940201_0315_2340G305570M.fits ft940201_0315_2340G306570M.fits ft940201_0315_2340G306999.fits ft940201_0315_2340G307470H.fits ft940201_0315_2340G307570M.fits ft940201_0315_2340G307670M.fits ft940201_0315_2340G307770H.fits ft940201_0315_2340G307870H.fits ft940201_0315_2340G307970H.fits ft940201_0315_2340G308070H.fits ft940201_0315_2340G308170H.fits ft940201_0315_2340G308270H.fits ft940201_0315_2340G308599.fits ft940201_0315_2340G308870H.fits ft940201_0315_2340G308970H.fits ft940201_0315_2340G309070H.fits ft940201_0315_2340G309170H.fits ft940201_0315_2340S000202H.fits ft940201_0315_2340S000402M.fits ft940201_0315_2340S000805H.fits ft940201_0315_2340S001002H.fits ft940201_0315_2340S001399.fits ft940201_0315_2340S001602H.fits ft940201_0315_2340S002202H.fits ft940201_0315_2340S002602H.fits ft940201_0315_2340S002802M.fits ft940201_0315_2340S003099.fits ft940201_0315_2340S003199.fits ft940201_0315_2340S003302H.fits ft940201_0315_2340S003502M.fits ft940201_0315_2340S003902H.fits ft940201_0315_2340S004102M.fits ft940201_0315_2340S004599.fits ft940201_0315_2340S005001M.fits ft940201_0315_2340S005399.fits ft940201_0315_2340S100202H.fits ft940201_0315_2340S100402M.fits ft940201_0315_2340S100805H.fits ft940201_0315_2340S101299.fits ft940201_0315_2340S101502H.fits ft940201_0315_2340S102102H.fits ft940201_0315_2340S102502H.fits ft940201_0315_2340S102702M.fits ft940201_0315_2340S102999.fits ft940201_0315_2340S103099.fits ft940201_0315_2340S103202H.fits ft940201_0315_2340S103402M.fits ft940201_0315_2340S103802H.fits ft940201_0315_2340S104002M.fits ft940201_0315_2340S104499.fits ft940201_0315_2340S104701M.fits ft940201_0315_2340S105099.fits-> Checking for empty GTI extensions
ft940201_0315_2340S000101H.fits[3] ft940201_0315_2340S000302M.fits[3] ft940201_0315_2340S000502M.fits[3] ft940201_0315_2340S000602H.fits[3] ft940201_0315_2340S000701H.fits[3] ft940201_0315_2340S000901H.fits[3] ft940201_0315_2340S001102M.fits[3] ft940201_0315_2340S001202M.fits[3] ft940201_0315_2340S001402M.fits[3] ft940201_0315_2340S001501H.fits[3] ft940201_0315_2340S001702M.fits[3] ft940201_0315_2340S001802M.fits[3] ft940201_0315_2340S001902M.fits[3] ft940201_0315_2340S002001M.fits[3] ft940201_0315_2340S002101H.fits[3] ft940201_0315_2340S002302M.fits[3] ft940201_0315_2340S002401M.fits[3] ft940201_0315_2340S002501H.fits[3] ft940201_0315_2340S002702M.fits[3] ft940201_0315_2340S002902M.fits[3] ft940201_0315_2340S003201H.fits[3] ft940201_0315_2340S003402M.fits[3] ft940201_0315_2340S003602M.fits[3] ft940201_0315_2340S003701M.fits[3] ft940201_0315_2340S003801H.fits[3] ft940201_0315_2340S004002M.fits[3] ft940201_0315_2340S004202M.fits[3] ft940201_0315_2340S004301M.fits[3] ft940201_0315_2340S004401H.fits[3] ft940201_0315_2340S004601H.fits[3] ft940201_0315_2340S004701H.fits[3] ft940201_0315_2340S004801H.fits[3] ft940201_0315_2340S004901M.fits[3] ft940201_0315_2340S005101M.fits[3] ft940201_0315_2340S005201H.fits[3] ft940201_0315_2340S005401H.fits[3] ft940201_0315_2340S005501H.fits[3]-> Merging GTIs from the following files:
ft940201_0315_2340S100101H.fits[3] ft940201_0315_2340S100302M.fits[3] ft940201_0315_2340S100502M.fits[3] ft940201_0315_2340S100602H.fits[3] ft940201_0315_2340S100701H.fits[3] ft940201_0315_2340S100901H.fits[3] ft940201_0315_2340S101002M.fits[3] ft940201_0315_2340S101102M.fits[3] ft940201_0315_2340S101302M.fits[3] ft940201_0315_2340S101401H.fits[3] ft940201_0315_2340S101602M.fits[3] ft940201_0315_2340S101702M.fits[3] ft940201_0315_2340S101802M.fits[3] ft940201_0315_2340S101901M.fits[3] ft940201_0315_2340S102001H.fits[3] ft940201_0315_2340S102202M.fits[3] ft940201_0315_2340S102301M.fits[3] ft940201_0315_2340S102401H.fits[3] ft940201_0315_2340S102602M.fits[3] ft940201_0315_2340S102802M.fits[3] ft940201_0315_2340S103101H.fits[3] ft940201_0315_2340S103302M.fits[3] ft940201_0315_2340S103502M.fits[3] ft940201_0315_2340S103601M.fits[3] ft940201_0315_2340S103701H.fits[3] ft940201_0315_2340S103902M.fits[3] ft940201_0315_2340S104102M.fits[3] ft940201_0315_2340S104201M.fits[3] ft940201_0315_2340S104301H.fits[3] ft940201_0315_2340S104501H.fits[3] ft940201_0315_2340S104601M.fits[3] ft940201_0315_2340S104801M.fits[3] ft940201_0315_2340S104901H.fits[3] ft940201_0315_2340S105101H.fits[3] ft940201_0315_2340S105201H.fits[3]-> Merging GTIs from the following files:
ft940201_0315_2340G200170H.fits[3] ft940201_0315_2340G200270M.fits[3] ft940201_0315_2340G200370M.fits[3] ft940201_0315_2340G200470M.fits[3] ft940201_0315_2340G200670M.fits[3] ft940201_0315_2340G200770M.fits[3] ft940201_0315_2340G200870H.fits[3] ft940201_0315_2340G200970H.fits[3] ft940201_0315_2340G201070H.fits[3] ft940201_0315_2340G201170H.fits[3] ft940201_0315_2340G201270M.fits[3] ft940201_0315_2340G201370M.fits[3] ft940201_0315_2340G201470M.fits[3] ft940201_0315_2340G201870M.fits[3] ft940201_0315_2340G201970M.fits[3] ft940201_0315_2340G202070M.fits[3] ft940201_0315_2340G202270M.fits[3] ft940201_0315_2340G202370M.fits[3] ft940201_0315_2340G202470H.fits[3] ft940201_0315_2340G202570M.fits[3] ft940201_0315_2340G202670M.fits[3] ft940201_0315_2340G202770H.fits[3] ft940201_0315_2340G202870H.fits[3] ft940201_0315_2340G202970H.fits[3] ft940201_0315_2340G203070H.fits[3] ft940201_0315_2340G203170M.fits[3] ft940201_0315_2340G203270M.fits[3] ft940201_0315_2340G203370M.fits[3] ft940201_0315_2340G203570M.fits[3] ft940201_0315_2340G203670M.fits[3] ft940201_0315_2340G203870H.fits[3] ft940201_0315_2340G203970H.fits[3] ft940201_0315_2340G204070H.fits[3] ft940201_0315_2340G204170M.fits[3] ft940201_0315_2340G204270M.fits[3] ft940201_0315_2340G204370M.fits[3] ft940201_0315_2340G204570M.fits[3] ft940201_0315_2340G204670M.fits[3] ft940201_0315_2340G204870H.fits[3] ft940201_0315_2340G204970H.fits[3] ft940201_0315_2340G205070H.fits[3] ft940201_0315_2340G205170H.fits[3] ft940201_0315_2340G205270M.fits[3] ft940201_0315_2340G205370M.fits[3] ft940201_0315_2340G205470M.fits[3] ft940201_0315_2340G205670M.fits[3] ft940201_0315_2340G205770M.fits[3] ft940201_0315_2340G205870H.fits[3] ft940201_0315_2340G205970H.fits[3] ft940201_0315_2340G206070H.fits[3] ft940201_0315_2340G206170H.fits[3] ft940201_0315_2340G206270M.fits[3] ft940201_0315_2340G206370M.fits[3] ft940201_0315_2340G206470M.fits[3] ft940201_0315_2340G206670M.fits[3] ft940201_0315_2340G206770M.fits[3] ft940201_0315_2340G206870H.fits[3] ft940201_0315_2340G207070H.fits[3] ft940201_0315_2340G207170H.fits[3] ft940201_0315_2340G208170H.fits[3] ft940201_0315_2340G208270H.fits[3] ft940201_0315_2340G208470H.fits[3] ft940201_0315_2340G208970H.fits[3] ft940201_0315_2340G209070H.fits[3] ft940201_0315_2340G209170H.fits[3]-> Merging GTIs from the following files:
ft940201_0315_2340G300170H.fits[3] ft940201_0315_2340G300270M.fits[3] ft940201_0315_2340G300370M.fits[3] ft940201_0315_2340G300470M.fits[3] ft940201_0315_2340G300670M.fits[3] ft940201_0315_2340G300770M.fits[3] ft940201_0315_2340G300970H.fits[3] ft940201_0315_2340G301070H.fits[3] ft940201_0315_2340G301170H.fits[3] ft940201_0315_2340G301270M.fits[3] ft940201_0315_2340G301370M.fits[3] ft940201_0315_2340G301470M.fits[3] ft940201_0315_2340G301870M.fits[3] ft940201_0315_2340G301970M.fits[3] ft940201_0315_2340G302070M.fits[3] ft940201_0315_2340G302270M.fits[3] ft940201_0315_2340G302370M.fits[3] ft940201_0315_2340G302470H.fits[3] ft940201_0315_2340G302570M.fits[3] ft940201_0315_2340G302670M.fits[3] ft940201_0315_2340G302770H.fits[3] ft940201_0315_2340G302870H.fits[3] ft940201_0315_2340G302970H.fits[3] ft940201_0315_2340G303070H.fits[3] ft940201_0315_2340G303170M.fits[3] ft940201_0315_2340G303270M.fits[3] ft940201_0315_2340G303370M.fits[3] ft940201_0315_2340G303570M.fits[3] ft940201_0315_2340G303670M.fits[3] ft940201_0315_2340G303770H.fits[3] ft940201_0315_2340G303970H.fits[3] ft940201_0315_2340G304070H.fits[3] ft940201_0315_2340G304170M.fits[3] ft940201_0315_2340G304270M.fits[3] ft940201_0315_2340G304370M.fits[3] ft940201_0315_2340G304570M.fits[3] ft940201_0315_2340G304670M.fits[3] ft940201_0315_2340G304870H.fits[3] ft940201_0315_2340G304970H.fits[3] ft940201_0315_2340G305070H.fits[3] ft940201_0315_2340G305170H.fits[3] ft940201_0315_2340G305270M.fits[3] ft940201_0315_2340G305370M.fits[3] ft940201_0315_2340G305470M.fits[3] ft940201_0315_2340G305670M.fits[3] ft940201_0315_2340G305770M.fits[3] ft940201_0315_2340G305870H.fits[3] ft940201_0315_2340G305970H.fits[3] ft940201_0315_2340G306070H.fits[3] ft940201_0315_2340G306170H.fits[3] ft940201_0315_2340G306270M.fits[3] ft940201_0315_2340G306370M.fits[3] ft940201_0315_2340G306470M.fits[3] ft940201_0315_2340G306670M.fits[3] ft940201_0315_2340G306770M.fits[3] ft940201_0315_2340G306870H.fits[3] ft940201_0315_2340G307070H.fits[3] ft940201_0315_2340G307170H.fits[3] ft940201_0315_2340G307270H.fits[3] ft940201_0315_2340G307370H.fits[3] ft940201_0315_2340G308370H.fits[3] ft940201_0315_2340G308470H.fits[3] ft940201_0315_2340G308670H.fits[3] ft940201_0315_2340G308770H.fits[3] ft940201_0315_2340G309270H.fits[3] ft940201_0315_2340G309370H.fits[3] ft940201_0315_2340G309470H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 12 photon cnt = 14318 GISSORTSPLIT:LO:g200470h.prelist merge count = 5 photon cnt = 9 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200170m.prelist merge count = 7 photon cnt = 27 GISSORTSPLIT:LO:g200270m.prelist merge count = 7 photon cnt = 74 GISSORTSPLIT:LO:g200370m.prelist merge count = 14 photon cnt = 46703 GISSORTSPLIT:LO:g200470m.prelist merge count = 7 photon cnt = 289 GISSORTSPLIT:LO:Total filenames split = 65 GISSORTSPLIT:LO:Total split file cnt = 19 GISSORTSPLIT:LO:End program-> Creating ad71039000g200170m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340G200370M.fits 2 -- ft940201_0315_2340G200770M.fits 3 -- ft940201_0315_2340G201370M.fits 4 -- ft940201_0315_2340G201970M.fits 5 -- ft940201_0315_2340G202370M.fits 6 -- ft940201_0315_2340G202670M.fits 7 -- ft940201_0315_2340G203270M.fits 8 -- ft940201_0315_2340G203670M.fits 9 -- ft940201_0315_2340G204270M.fits 10 -- ft940201_0315_2340G204670M.fits 11 -- ft940201_0315_2340G205370M.fits 12 -- ft940201_0315_2340G205770M.fits 13 -- ft940201_0315_2340G206370M.fits 14 -- ft940201_0315_2340G206770M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340G200370M.fits 2 -- ft940201_0315_2340G200770M.fits 3 -- ft940201_0315_2340G201370M.fits 4 -- ft940201_0315_2340G201970M.fits 5 -- ft940201_0315_2340G202370M.fits 6 -- ft940201_0315_2340G202670M.fits 7 -- ft940201_0315_2340G203270M.fits 8 -- ft940201_0315_2340G203670M.fits 9 -- ft940201_0315_2340G204270M.fits 10 -- ft940201_0315_2340G204670M.fits 11 -- ft940201_0315_2340G205370M.fits 12 -- ft940201_0315_2340G205770M.fits 13 -- ft940201_0315_2340G206370M.fits 14 -- ft940201_0315_2340G206770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000g200270h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340G200170H.fits 2 -- ft940201_0315_2340G201170H.fits 3 -- ft940201_0315_2340G202470H.fits 4 -- ft940201_0315_2340G203070H.fits 5 -- ft940201_0315_2340G204070H.fits 6 -- ft940201_0315_2340G205170H.fits 7 -- ft940201_0315_2340G206170H.fits 8 -- ft940201_0315_2340G206870H.fits 9 -- ft940201_0315_2340G207070H.fits 10 -- ft940201_0315_2340G208270H.fits 11 -- ft940201_0315_2340G208470H.fits 12 -- ft940201_0315_2340G209170H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340G200170H.fits 2 -- ft940201_0315_2340G201170H.fits 3 -- ft940201_0315_2340G202470H.fits 4 -- ft940201_0315_2340G203070H.fits 5 -- ft940201_0315_2340G204070H.fits 6 -- ft940201_0315_2340G205170H.fits 7 -- ft940201_0315_2340G206170H.fits 8 -- ft940201_0315_2340G206870H.fits 9 -- ft940201_0315_2340G207070H.fits 10 -- ft940201_0315_2340G208270H.fits 11 -- ft940201_0315_2340G208470H.fits 12 -- ft940201_0315_2340G209170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000289 events
ft940201_0315_2340G200270M.fits ft940201_0315_2340G201270M.fits ft940201_0315_2340G202570M.fits ft940201_0315_2340G203170M.fits ft940201_0315_2340G204170M.fits ft940201_0315_2340G205270M.fits ft940201_0315_2340G206270M.fits-> Ignoring the following files containing 000000074 events
ft940201_0315_2340G200670M.fits ft940201_0315_2340G201870M.fits ft940201_0315_2340G202270M.fits ft940201_0315_2340G203570M.fits ft940201_0315_2340G204570M.fits ft940201_0315_2340G205670M.fits ft940201_0315_2340G206670M.fits-> Ignoring the following files containing 000000027 events
ft940201_0315_2340G200470M.fits ft940201_0315_2340G201470M.fits ft940201_0315_2340G202070M.fits ft940201_0315_2340G203370M.fits ft940201_0315_2340G204370M.fits ft940201_0315_2340G205470M.fits ft940201_0315_2340G206470M.fits-> Ignoring the following files containing 000000009 events
ft940201_0315_2340G209070H.fits-> Ignoring the following files containing 000000009 events
ft940201_0315_2340G201070H.fits ft940201_0315_2340G202970H.fits ft940201_0315_2340G203970H.fits ft940201_0315_2340G205070H.fits ft940201_0315_2340G206070H.fits-> Ignoring the following files containing 000000005 events
ft940201_0315_2340G200970H.fits-> Ignoring the following files containing 000000004 events
ft940201_0315_2340G204970H.fits-> Ignoring the following files containing 000000003 events
ft940201_0315_2340G200870H.fits-> Ignoring the following files containing 000000003 events
ft940201_0315_2340G204870H.fits-> Ignoring the following files containing 000000003 events
ft940201_0315_2340G202870H.fits-> Ignoring the following files containing 000000003 events
ft940201_0315_2340G208170H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G208970H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G205970H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G205870H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G202770H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G203870H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G207170H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300570h.prelist merge count = 13 photon cnt = 13686 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300770h.prelist merge count = 5 photon cnt = 9 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300170m.prelist merge count = 7 photon cnt = 30 GISSORTSPLIT:LO:g300270m.prelist merge count = 7 photon cnt = 67 GISSORTSPLIT:LO:g300370m.prelist merge count = 14 photon cnt = 43831 GISSORTSPLIT:LO:g300470m.prelist merge count = 7 photon cnt = 286 GISSORTSPLIT:LO:Total filenames split = 67 GISSORTSPLIT:LO:Total split file cnt = 20 GISSORTSPLIT:LO:End program-> Creating ad71039000g300170m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340G300370M.fits 2 -- ft940201_0315_2340G300770M.fits 3 -- ft940201_0315_2340G301370M.fits 4 -- ft940201_0315_2340G301970M.fits 5 -- ft940201_0315_2340G302370M.fits 6 -- ft940201_0315_2340G302670M.fits 7 -- ft940201_0315_2340G303270M.fits 8 -- ft940201_0315_2340G303670M.fits 9 -- ft940201_0315_2340G304270M.fits 10 -- ft940201_0315_2340G304670M.fits 11 -- ft940201_0315_2340G305370M.fits 12 -- ft940201_0315_2340G305770M.fits 13 -- ft940201_0315_2340G306370M.fits 14 -- ft940201_0315_2340G306770M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340G300370M.fits 2 -- ft940201_0315_2340G300770M.fits 3 -- ft940201_0315_2340G301370M.fits 4 -- ft940201_0315_2340G301970M.fits 5 -- ft940201_0315_2340G302370M.fits 6 -- ft940201_0315_2340G302670M.fits 7 -- ft940201_0315_2340G303270M.fits 8 -- ft940201_0315_2340G303670M.fits 9 -- ft940201_0315_2340G304270M.fits 10 -- ft940201_0315_2340G304670M.fits 11 -- ft940201_0315_2340G305370M.fits 12 -- ft940201_0315_2340G305770M.fits 13 -- ft940201_0315_2340G306370M.fits 14 -- ft940201_0315_2340G306770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000g300270h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340G300170H.fits 2 -- ft940201_0315_2340G301170H.fits 3 -- ft940201_0315_2340G302470H.fits 4 -- ft940201_0315_2340G303070H.fits 5 -- ft940201_0315_2340G304070H.fits 6 -- ft940201_0315_2340G305170H.fits 7 -- ft940201_0315_2340G306170H.fits 8 -- ft940201_0315_2340G306870H.fits 9 -- ft940201_0315_2340G307070H.fits 10 -- ft940201_0315_2340G307270H.fits 11 -- ft940201_0315_2340G308470H.fits 12 -- ft940201_0315_2340G308670H.fits 13 -- ft940201_0315_2340G309470H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340G300170H.fits 2 -- ft940201_0315_2340G301170H.fits 3 -- ft940201_0315_2340G302470H.fits 4 -- ft940201_0315_2340G303070H.fits 5 -- ft940201_0315_2340G304070H.fits 6 -- ft940201_0315_2340G305170H.fits 7 -- ft940201_0315_2340G306170H.fits 8 -- ft940201_0315_2340G306870H.fits 9 -- ft940201_0315_2340G307070H.fits 10 -- ft940201_0315_2340G307270H.fits 11 -- ft940201_0315_2340G308470H.fits 12 -- ft940201_0315_2340G308670H.fits 13 -- ft940201_0315_2340G309470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000286 events
ft940201_0315_2340G300270M.fits ft940201_0315_2340G301270M.fits ft940201_0315_2340G302570M.fits ft940201_0315_2340G303170M.fits ft940201_0315_2340G304170M.fits ft940201_0315_2340G305270M.fits ft940201_0315_2340G306270M.fits-> Ignoring the following files containing 000000067 events
ft940201_0315_2340G300670M.fits ft940201_0315_2340G301870M.fits ft940201_0315_2340G302270M.fits ft940201_0315_2340G303570M.fits ft940201_0315_2340G304570M.fits ft940201_0315_2340G305670M.fits ft940201_0315_2340G306670M.fits-> Ignoring the following files containing 000000030 events
ft940201_0315_2340G300470M.fits ft940201_0315_2340G301470M.fits ft940201_0315_2340G302070M.fits ft940201_0315_2340G303370M.fits ft940201_0315_2340G304370M.fits ft940201_0315_2340G305470M.fits ft940201_0315_2340G306470M.fits-> Ignoring the following files containing 000000011 events
ft940201_0315_2340G308770H.fits-> Ignoring the following files containing 000000009 events
ft940201_0315_2340G301070H.fits ft940201_0315_2340G302970H.fits ft940201_0315_2340G303970H.fits ft940201_0315_2340G305070H.fits ft940201_0315_2340G306070H.fits-> Ignoring the following files containing 000000004 events
ft940201_0315_2340G303770H.fits-> Ignoring the following files containing 000000004 events
ft940201_0315_2340G300970H.fits-> Ignoring the following files containing 000000004 events
ft940201_0315_2340G309370H.fits-> Ignoring the following files containing 000000003 events
ft940201_0315_2340G308370H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G302870H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G305970H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G307370H.fits-> Ignoring the following files containing 000000002 events
ft940201_0315_2340G309270H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G302770H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G304970H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G304870H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G305870H.fits-> Ignoring the following files containing 000000001 events
ft940201_0315_2340G307170H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 5376 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 13 photon cnt = 299535 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 18 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 6 photon cnt = 2931 SIS0SORTSPLIT:LO:s000502h.prelist merge count = 1 photon cnt = 159 SIS0SORTSPLIT:LO:s000602m.prelist merge count = 13 photon cnt = 258554 SIS0SORTSPLIT:LO:s000702m.prelist merge count = 2 photon cnt = 35 SIS0SORTSPLIT:LO:Total filenames split = 37 SIS0SORTSPLIT:LO:Total split file cnt = 7 SIS0SORTSPLIT:LO:End program-> Creating ad71039000s000101h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S000101H.fits 2 -- ft940201_0315_2340S000701H.fits 3 -- ft940201_0315_2340S000901H.fits 4 -- ft940201_0315_2340S001501H.fits 5 -- ft940201_0315_2340S002101H.fits 6 -- ft940201_0315_2340S002501H.fits 7 -- ft940201_0315_2340S003201H.fits 8 -- ft940201_0315_2340S003801H.fits 9 -- ft940201_0315_2340S004401H.fits 10 -- ft940201_0315_2340S004601H.fits 11 -- ft940201_0315_2340S004801H.fits 12 -- ft940201_0315_2340S005201H.fits 13 -- ft940201_0315_2340S005401H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S000101H.fits 2 -- ft940201_0315_2340S000701H.fits 3 -- ft940201_0315_2340S000901H.fits 4 -- ft940201_0315_2340S001501H.fits 5 -- ft940201_0315_2340S002101H.fits 6 -- ft940201_0315_2340S002501H.fits 7 -- ft940201_0315_2340S003201H.fits 8 -- ft940201_0315_2340S003801H.fits 9 -- ft940201_0315_2340S004401H.fits 10 -- ft940201_0315_2340S004601H.fits 11 -- ft940201_0315_2340S004801H.fits 12 -- ft940201_0315_2340S005201H.fits 13 -- ft940201_0315_2340S005401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000s000202m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S000302M.fits 2 -- ft940201_0315_2340S000502M.fits 3 -- ft940201_0315_2340S001102M.fits 4 -- ft940201_0315_2340S001402M.fits 5 -- ft940201_0315_2340S001702M.fits 6 -- ft940201_0315_2340S001902M.fits 7 -- ft940201_0315_2340S002302M.fits 8 -- ft940201_0315_2340S002702M.fits 9 -- ft940201_0315_2340S002902M.fits 10 -- ft940201_0315_2340S003402M.fits 11 -- ft940201_0315_2340S003602M.fits 12 -- ft940201_0315_2340S004002M.fits 13 -- ft940201_0315_2340S004202M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S000302M.fits 2 -- ft940201_0315_2340S000502M.fits 3 -- ft940201_0315_2340S001102M.fits 4 -- ft940201_0315_2340S001402M.fits 5 -- ft940201_0315_2340S001702M.fits 6 -- ft940201_0315_2340S001902M.fits 7 -- ft940201_0315_2340S002302M.fits 8 -- ft940201_0315_2340S002702M.fits 9 -- ft940201_0315_2340S002902M.fits 10 -- ft940201_0315_2340S003402M.fits 11 -- ft940201_0315_2340S003602M.fits 12 -- ft940201_0315_2340S004002M.fits 13 -- ft940201_0315_2340S004202M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft940201_0315_2340S005501H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S005501H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S005501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000s000401m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S002001M.fits 2 -- ft940201_0315_2340S002401M.fits 3 -- ft940201_0315_2340S003701M.fits 4 -- ft940201_0315_2340S004301M.fits 5 -- ft940201_0315_2340S004901M.fits 6 -- ft940201_0315_2340S005101M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S002001M.fits 2 -- ft940201_0315_2340S002401M.fits 3 -- ft940201_0315_2340S003701M.fits 4 -- ft940201_0315_2340S004301M.fits 5 -- ft940201_0315_2340S004901M.fits 6 -- ft940201_0315_2340S005101M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000159 events
ft940201_0315_2340S000602H.fits-> Ignoring the following files containing 000000035 events
ft940201_0315_2340S001202M.fits ft940201_0315_2340S001802M.fits-> Ignoring the following files containing 000000018 events
ft940201_0315_2340S004701H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 5563 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 12 photon cnt = 272049 SIS1SORTSPLIT:LO:s100301m.prelist merge count = 6 photon cnt = 3104 SIS1SORTSPLIT:LO:s100402h.prelist merge count = 1 photon cnt = 135 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 13 photon cnt = 221467 SIS1SORTSPLIT:LO:s100602m.prelist merge count = 2 photon cnt = 50 SIS1SORTSPLIT:LO:Total filenames split = 35 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad71039000s100101h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S100101H.fits 2 -- ft940201_0315_2340S100701H.fits 3 -- ft940201_0315_2340S100901H.fits 4 -- ft940201_0315_2340S101401H.fits 5 -- ft940201_0315_2340S102001H.fits 6 -- ft940201_0315_2340S102401H.fits 7 -- ft940201_0315_2340S103101H.fits 8 -- ft940201_0315_2340S103701H.fits 9 -- ft940201_0315_2340S104301H.fits 10 -- ft940201_0315_2340S104501H.fits 11 -- ft940201_0315_2340S104901H.fits 12 -- ft940201_0315_2340S105101H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S100101H.fits 2 -- ft940201_0315_2340S100701H.fits 3 -- ft940201_0315_2340S100901H.fits 4 -- ft940201_0315_2340S101401H.fits 5 -- ft940201_0315_2340S102001H.fits 6 -- ft940201_0315_2340S102401H.fits 7 -- ft940201_0315_2340S103101H.fits 8 -- ft940201_0315_2340S103701H.fits 9 -- ft940201_0315_2340S104301H.fits 10 -- ft940201_0315_2340S104501H.fits 11 -- ft940201_0315_2340S104901H.fits 12 -- ft940201_0315_2340S105101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000s100202m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S100302M.fits 2 -- ft940201_0315_2340S100502M.fits 3 -- ft940201_0315_2340S101002M.fits 4 -- ft940201_0315_2340S101302M.fits 5 -- ft940201_0315_2340S101602M.fits 6 -- ft940201_0315_2340S101802M.fits 7 -- ft940201_0315_2340S102202M.fits 8 -- ft940201_0315_2340S102602M.fits 9 -- ft940201_0315_2340S102802M.fits 10 -- ft940201_0315_2340S103302M.fits 11 -- ft940201_0315_2340S103502M.fits 12 -- ft940201_0315_2340S103902M.fits 13 -- ft940201_0315_2340S104102M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S100302M.fits 2 -- ft940201_0315_2340S100502M.fits 3 -- ft940201_0315_2340S101002M.fits 4 -- ft940201_0315_2340S101302M.fits 5 -- ft940201_0315_2340S101602M.fits 6 -- ft940201_0315_2340S101802M.fits 7 -- ft940201_0315_2340S102202M.fits 8 -- ft940201_0315_2340S102602M.fits 9 -- ft940201_0315_2340S102802M.fits 10 -- ft940201_0315_2340S103302M.fits 11 -- ft940201_0315_2340S103502M.fits 12 -- ft940201_0315_2340S103902M.fits 13 -- ft940201_0315_2340S104102M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft940201_0315_2340S105201H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S105201H.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S105201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71039000s100401m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940201_0315_2340S101901M.fits 2 -- ft940201_0315_2340S102301M.fits 3 -- ft940201_0315_2340S103601M.fits 4 -- ft940201_0315_2340S104201M.fits 5 -- ft940201_0315_2340S104601M.fits 6 -- ft940201_0315_2340S104801M.fits Merging binary extension #: 2 1 -- ft940201_0315_2340S101901M.fits 2 -- ft940201_0315_2340S102301M.fits 3 -- ft940201_0315_2340S103601M.fits 4 -- ft940201_0315_2340S104201M.fits 5 -- ft940201_0315_2340S104601M.fits 6 -- ft940201_0315_2340S104801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000135 events
ft940201_0315_2340S100602H.fits-> Ignoring the following files containing 000000050 events
ft940201_0315_2340S101102M.fits ft940201_0315_2340S101702M.fits-> Tar-ing together the leftover raw files
a ft940201_0315_2340G200270M.fits 40K a ft940201_0315_2340G200470M.fits 40K a ft940201_0315_2340G200670M.fits 40K a ft940201_0315_2340G200870H.fits 40K a ft940201_0315_2340G200970H.fits 40K a ft940201_0315_2340G201070H.fits 40K a ft940201_0315_2340G201270M.fits 40K a ft940201_0315_2340G201470M.fits 40K a ft940201_0315_2340G201870M.fits 40K a ft940201_0315_2340G202070M.fits 40K a ft940201_0315_2340G202270M.fits 40K a ft940201_0315_2340G202570M.fits 40K a ft940201_0315_2340G202770H.fits 40K a ft940201_0315_2340G202870H.fits 40K a ft940201_0315_2340G202970H.fits 40K a ft940201_0315_2340G203170M.fits 40K a ft940201_0315_2340G203370M.fits 40K a ft940201_0315_2340G203570M.fits 40K a ft940201_0315_2340G203870H.fits 40K a ft940201_0315_2340G203970H.fits 40K a ft940201_0315_2340G204170M.fits 40K a ft940201_0315_2340G204370M.fits 40K a ft940201_0315_2340G204570M.fits 40K a ft940201_0315_2340G204870H.fits 40K a ft940201_0315_2340G204970H.fits 40K a ft940201_0315_2340G205070H.fits 40K a ft940201_0315_2340G205270M.fits 40K a ft940201_0315_2340G205470M.fits 40K a ft940201_0315_2340G205670M.fits 40K a ft940201_0315_2340G205870H.fits 40K a ft940201_0315_2340G205970H.fits 40K a ft940201_0315_2340G206070H.fits 40K a ft940201_0315_2340G206270M.fits 40K a ft940201_0315_2340G206470M.fits 40K a ft940201_0315_2340G206670M.fits 40K a ft940201_0315_2340G207170H.fits 40K a ft940201_0315_2340G208170H.fits 40K a ft940201_0315_2340G208970H.fits 40K a ft940201_0315_2340G209070H.fits 40K a ft940201_0315_2340G300270M.fits 40K a ft940201_0315_2340G300470M.fits 40K a ft940201_0315_2340G300670M.fits 40K a ft940201_0315_2340G300970H.fits 40K a ft940201_0315_2340G301070H.fits 40K a ft940201_0315_2340G301270M.fits 40K a ft940201_0315_2340G301470M.fits 40K a ft940201_0315_2340G301870M.fits 40K a ft940201_0315_2340G302070M.fits 40K a ft940201_0315_2340G302270M.fits 40K a ft940201_0315_2340G302570M.fits 40K a ft940201_0315_2340G302770H.fits 40K a ft940201_0315_2340G302870H.fits 40K a ft940201_0315_2340G302970H.fits 40K a ft940201_0315_2340G303170M.fits 40K a ft940201_0315_2340G303370M.fits 40K a ft940201_0315_2340G303570M.fits 40K a ft940201_0315_2340G303770H.fits 40K a ft940201_0315_2340G303970H.fits 40K a ft940201_0315_2340G304170M.fits 40K a ft940201_0315_2340G304370M.fits 40K a ft940201_0315_2340G304570M.fits 40K a ft940201_0315_2340G304870H.fits 40K a ft940201_0315_2340G304970H.fits 40K a ft940201_0315_2340G305070H.fits 40K a ft940201_0315_2340G305270M.fits 40K a ft940201_0315_2340G305470M.fits 40K a ft940201_0315_2340G305670M.fits 40K a ft940201_0315_2340G305870H.fits 40K a ft940201_0315_2340G305970H.fits 40K a ft940201_0315_2340G306070H.fits 40K a ft940201_0315_2340G306270M.fits 40K a ft940201_0315_2340G306470M.fits 40K a ft940201_0315_2340G306670M.fits 40K a ft940201_0315_2340G307170H.fits 40K a ft940201_0315_2340G307370H.fits 40K a ft940201_0315_2340G308370H.fits 40K a ft940201_0315_2340G308770H.fits 40K a ft940201_0315_2340G309270H.fits 40K a ft940201_0315_2340G309370H.fits 40K a ft940201_0315_2340S000602H.fits 43K a ft940201_0315_2340S001202M.fits 40K a ft940201_0315_2340S001802M.fits 40K a ft940201_0315_2340S004701H.fits 40K a ft940201_0315_2340S100602H.fits 43K a ft940201_0315_2340S101102M.fits 40K a ft940201_0315_2340S101702M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft940201_0315.2340 'ft940201_0315.2340' is successfully opened Data Start Time is 34226158.62 (940201 031558) Time Margin 2.0 sec included Sync error detected in 5964 th SF Sync error detected in 5965 th SF Sync error detected in 5966 th SF Sync error detected in 5967 th SF Sync error detected in 5968 th SF Sync error detected in 8397 th SF Sync error detected in 8398 th SF 'ft940201_0315.2340' EOF detected, sf=10887 Data End Time is 34299640.41 (940201 234040) Gain History is written in ft940201_0315_2340.ghf-> Checking if column CAL_START in ft940201_0315_2340.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft940201_0315_2340.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad71039000g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000302h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000312h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s000401m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100401m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71039000s100412m.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 94/ 2/ 1 3:15 mjd=49384.135417 Orbit file name is ./frf.orbit.208 Epoch of Orbital Elements: 1994/2/1 0:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa940201_0315.2340 S0-HK file: ft940201_0315_2340S0HK.fits S1-HK file: ft940201_0315_2340S1HK.fits G2-HK file: ft940201_0315_2340G2HK.fits G3-HK file: ft940201_0315_2340G3HK.fits output FITS File: ft940201_0315_2340.mkf Total 2297 Data bins were processed.-> Checking if column TIME in ft940201_0315_2340.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 7454.8807 The mean of the selected column is 26.066017 The standard deviation of the selected column is 8.7218435 The minimum of selected column is 1.8948965 The maximum of selected column is 71.125206 The number of points used in calculation is 286-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5711.8112 The mean of the selected column is 19.971368 The standard deviation of the selected column is 8.5429085 The minimum of selected column is 0.69886738 The maximum of selected column is 64.656441 The number of points used in calculation is 286-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0 && S0_PIXL0<52.2 )&& (S0_PIXL1>0.0 && S0_PIXL1<45.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.14E+05 111829 1100
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
107164 77662 0 29502 0 0
Writing events file
77662 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
107164 77662 0 29502 0 0
in 9006.17 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 77662
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 59 58025
Flickering pixels iter, pixels & cnts : 1 59 984
cleaning chip # 1
Hot pixels & counts : 20 17502
Flickering pixels iter, pixels & cnts : 1 6 153
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 144
Number of (internal) image counts : 77662
Number of image cts rejected (N, %) : 76664 98.7149429
By chip : 0 1 2 3
Pixels rejected : 118 26 0 0
Image counts : 59556 18106 0 0
Image cts rejected: 59009 17655 0 0
Image cts rej (%) : 99.08 97.51 0.00 0.00
filtering data...
Total counts : 59556 18106 0 0
Total cts rejected: 59009 17655 0 0
Total cts rej (%) : 99.08 97.51 0.00 0.00
Number of clean counts accepted : 998
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 144
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71039000s000102h.evt use_events=no
Wrote cleaned events file to ad71039000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad71039000s000112h.unf into ad71039000s000112h.evtThe sum of the selected column is 7454.8807 The mean of the selected column is 26.066017 The standard deviation of the selected column is 8.7218435 The minimum of selected column is 1.8948965 The maximum of selected column is 71.125206 The number of points used in calculation is 286-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5711.8112 The mean of the selected column is 19.971368 The standard deviation of the selected column is 8.5429085 The minimum of selected column is 0.69886738 The maximum of selected column is 64.656441 The number of points used in calculation is 286-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0 && S0_PIXL0<52.2 )&& (S0_PIXL1>0.0 && S0_PIXL1<45.6 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.14E+05 112207 1100
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
107310 77742 0 29568 0 0
Writing events file
77742 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
107310 77742 0 29568 0 0
in 9006.17 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 77742
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 59 58035
Flickering pixels iter, pixels & cnts : 1 59 984
cleaning chip # 1
Hot pixels & counts : 20 17502
Flickering pixels iter, pixels & cnts : 1 6 153
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 144
Number of (internal) image counts : 77742
Number of image cts rejected (N, %) : 76674 98.6262283
By chip : 0 1 2 3
Pixels rejected : 118 26 0 0
Image counts : 59606 18136 0 0
Image cts rejected: 59019 17655 0 0
Image cts rej (%) : 99.02 97.35 0.00 0.00
filtering data...
Total counts : 59606 18136 0 0
Total cts rejected: 59019 17655 0 0
Total cts rej (%) : 99.02 97.35 0.00 0.00
Number of clean counts accepted : 1068
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 144
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad71039000s000112h.evt use_events=no
Wrote cleaned events file to ad71039000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad71039000s000202m.unf into ad71039000s000202m.evtThe sum of the selected column is 17378.848 The mean of the selected column is 31.369763 The standard deviation of the selected column is 34.311138 The minimum of selected column is 11.250032 The maximum of selected column is 502.97021 The number of points used in calculation is 554-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13921.444 The mean of the selected column is 25.128960 The standard deviation of the selected column is 32.033096 The minimum of selected column is 3.9062614 The maximum of selected column is 488.22018 The number of points used in calculation is 554-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<134.3 )&& (S0_PIXL1>0.0 && S0_PIXL1<121.2 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.48E+05 258554 1100
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
247363 150500 0 96863 0 0
Writing events file
150500 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
247363 150500 0 96863 0 0
in 17616.68 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 150500
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 59 112925
Flickering pixels iter, pixels & cnts : 1 21 1366
cleaning chip # 1
Hot pixels & counts : 20 33945
Flickering pixels iter, pixels & cnts : 1 8 243
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 108
Number of (internal) image counts : 150500
Number of image cts rejected (N, %) : 148479 98.6571426
By chip : 0 1 2 3
Pixels rejected : 80 28 0 0
Image counts : 115339 35161 0 0
Image cts rejected: 114291 34188 0 0
Image cts rej (%) : 99.09 97.23 0.00 0.00
filtering data...
Total counts : 115339 35161 0 0
Total cts rejected: 114291 34188 0 0
Total cts rej (%) : 99.09 97.23 0.00 0.00
Number of clean counts accepted : 2021
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 108
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71039000s000202m.evt use_events=no
Wrote cleaned events file to ad71039000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad71039000s000301h.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 23:39:08 0.82E+02 5120 0100
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s000302h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71039000s000302h.evt use_events=no
Wrote cleaned events file to ad71039000s000302h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71039000s000302h.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 23:39:08 0.82E+02 5120 0100
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s000312h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad71039000s000312h.evt use_events=no
Wrote cleaned events file to ad71039000s000312h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s000312h.evt since it contains 0 eventsThe sum of the selected column is 8720.9523 The mean of the selected column is 30.492840 The standard deviation of the selected column is 12.670205 The minimum of selected column is 2.1903527 The maximum of selected column is 81.656487 The number of points used in calculation is 286-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9564.5900 The mean of the selected column is 33.442622 The standard deviation of the selected column is 14.085845 The minimum of selected column is 4.2272954 The maximum of selected column is 97.250282 The number of points used in calculation is 286-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<68.5 )&& (S1_PIXL3>0.0 && S1_PIXL3<75.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.14E+05 88590 0011
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
84377 60231 0 24146 0 0
Writing events file
60231 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
84377 60231 0 24146 0 0
in 8954.91 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 60231
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 31 27022
Flickering pixels iter, pixels & cnts : 1 9 206
cleaning chip # 3
Hot pixels & counts : 38 31306
Flickering pixels iter, pixels & cnts : 1 88 554
Number of pixels rejected : 166
Number of (internal) image counts : 60231
Number of image cts rejected (N, %) : 59088 98.1023026
By chip : 0 1 2 3
Pixels rejected : 0 0 40 126
Image counts : 0 0 27730 32501
Image cts rejected: 0 0 27228 31860
Image cts rej (%) : 0.00 0.00 98.19 98.03
filtering data...
Total counts : 0 0 27730 32501
Total cts rejected: 0 0 27228 31860
Total cts rej (%) : 0.00 0.00 98.19 98.03
Number of clean counts accepted : 1143
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 166
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71039000s100102h.evt use_events=no
Wrote cleaned events file to ad71039000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad71039000s100112h.unf into ad71039000s100112h.evtThe sum of the selected column is 8720.9523 The mean of the selected column is 30.492840 The standard deviation of the selected column is 12.670205 The minimum of selected column is 2.1903527 The maximum of selected column is 81.656487 The number of points used in calculation is 286-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9564.5900 The mean of the selected column is 33.442622 The standard deviation of the selected column is 14.085845 The minimum of selected column is 4.2272954 The maximum of selected column is 97.250282 The number of points used in calculation is 286-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<68.5 )&& (S1_PIXL3>0.0 && S1_PIXL3<75.7 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.14E+05 88856 0011
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
84504 60302 0 24202 0 0
Writing events file
60302 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
84504 60302 0 24202 0 0
in 8954.91 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 60302
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 31 27025
Flickering pixels iter, pixels & cnts : 1 9 206
cleaning chip # 3
Hot pixels & counts : 38 31312
Flickering pixels iter, pixels & cnts : 1 88 555
Number of pixels rejected : 166
Number of (internal) image counts : 60302
Number of image cts rejected (N, %) : 59098 98.0033798
By chip : 0 1 2 3
Pixels rejected : 0 0 40 126
Image counts : 0 0 27766 32536
Image cts rejected: 0 0 27231 31867
Image cts rej (%) : 0.00 0.00 98.07 97.94
filtering data...
Total counts : 0 0 27766 32536
Total cts rejected: 0 0 27231 31867
Total cts rej (%) : 0.00 0.00 98.07 97.94
Number of clean counts accepted : 1204
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 166
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad71039000s100112h.evt use_events=no
Wrote cleaned events file to ad71039000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad71039000s100202m.unf into ad71039000s100202m.evtThe sum of the selected column is 22024.255 The mean of the selected column is 39.754974 The standard deviation of the selected column is 51.320625 The minimum of selected column is 8.7187757 The maximum of selected column is 705.12708 The number of points used in calculation is 554-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 24645.747 The mean of the selected column is 44.486909 The standard deviation of the selected column is 55.706883 The minimum of selected column is 12.531286 The maximum of selected column is 792.09607 The number of points used in calculation is 554-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<193.7 )&& (S1_PIXL3>0.0 && S1_PIXL3<211.6 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.48E+05 221467 0011
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
206788 116348 0 90440 0 0
Writing events file
116348 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
206788 116348 0 90440 0 0
in 17680.68 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 116348
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 31 52385
Flickering pixels iter, pixels & cnts : 1 9 363
cleaning chip # 3
Hot pixels & counts : 38 60814
Flickering pixels iter, pixels & cnts : 1 20 580
Number of pixels rejected : 98
Number of (internal) image counts : 116348
Number of image cts rejected (N, %) : 114142 98.1039658
By chip : 0 1 2 3
Pixels rejected : 0 0 40 58
Image counts : 0 0 53809 62539
Image cts rejected: 0 0 52748 61394
Image cts rej (%) : 0.00 0.00 98.03 98.17
filtering data...
Total counts : 0 0 53809 62539
Total cts rejected: 0 0 52748 61394
Total cts rej (%) : 0.00 0.00 98.03 98.17
Number of clean counts accepted : 2206
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 98
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71039000s100202m.evt use_events=no
Wrote cleaned events file to ad71039000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad71039000s100301h.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.40E+03 1070 0011
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1000 268 0 732 0 0
Writing events file
268 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1000 268 0 732 0 0
in 37.24 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 268
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 22 139
Flickering pixels iter, pixels & cnts : 1 4 16
cleaning chip # 3
Hot pixels & counts : 3 12
Flickering pixels iter, pixels & cnts : 1 17 51
Number of pixels rejected : 46
Number of (internal) image counts : 268
Number of image cts rejected (N, %) : 218 81.3432846
By chip : 0 1 2 3
Pixels rejected : 0 0 26 20
Image counts : 0 0 167 101
Image cts rejected: 0 0 155 63
Image cts rej (%) : 0.00 0.00 92.81 62.38
filtering data...
Total counts : 0 0 167 101
Total cts rejected: 0 0 155 63
Total cts rej (%) : 0.00 0.00 92.81 62.38
Number of clean counts accepted : 50
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 46
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s100402m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71039000s100402m.evt use_events=no
Wrote cleaned events file to ad71039000s100402m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad71039000s100412m.unf into ad71039000s100412m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 MEDIUM 01/02/94 15:05:18 0.40E+03 1074 0011
Processing file: /data/data24/seq_proc/71039000.004/ad71039000s100412m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1002 268 0 734 0 0
Writing events file
268 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1002 268 0 734 0 0
in 37.24 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/71039000.004/screen_in_event.xsl
reading data file: /data/data24/seq_proc/71039000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 268
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 22 139
Flickering pixels iter, pixels & cnts : 1 4 16
cleaning chip # 3
Hot pixels & counts : 3 12
Flickering pixels iter, pixels & cnts : 1 17 51
Number of pixels rejected : 46
Number of (internal) image counts : 268
Number of image cts rejected (N, %) : 218 81.3432846
By chip : 0 1 2 3
Pixels rejected : 0 0 26 20
Image counts : 0 0 167 101
Image cts rejected: 0 0 155 63
Image cts rej (%) : 0.00 0.00 92.81 62.38
filtering data...
Total counts : 0 0 167 101
Total cts rejected: 0 0 155 63
Total cts rej (%) : 0.00 0.00 92.81 62.38
Number of clean counts accepted : 50
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 46
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000s100412m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad71039000s100412m.evt use_events=no
Wrote cleaned events file to ad71039000s100412m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad71039000g200170m.unf into ad71039000g200170m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 46703 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.unf
Total Good Bad: Region Time Phase Cut
46703 5804 27963 12936 0 0
Writing events file
5804 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
46703 5804 27963 12936 0 0
in 18592.28 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5804 5092 712
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad71039000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 5092 in ad71039000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 14318 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.unf
Total Good Bad: Region Time Phase Cut
14318 3223 8708 2387 0 0
Writing events file
3223 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14318 3223 8708 2387 0 0
in 10480.52 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3223 2840 383
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad71039000g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 2840 in ad71039000g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 43831 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.unf
Total Good Bad: Region Time Phase Cut
43831 5797 24192 13842 0 0
Writing events file
5797 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
43831 5797 24192 13842 0 0
in 18592.28 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5797 4999 798
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad71039000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 4999 in ad71039000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 13686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.unf
Total Good Bad: Region Time Phase Cut
13686 3361 7725 2600 0 0
Writing events file
3361 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13686 3361 7725 2600 0 0
in 10476.52 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3361 2871 490
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!screen:ASCA > read events ad71039000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad71039000g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 2871 in ad71039000g300270h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad71039000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0548
Mean RA/DEC/ROLL : 196.8513 -23.6650 240.0548
Pnt RA/DEC/ROLL : 196.8781 -23.6744 240.0548
Image rebin factor : 1
Attitude Records : 43391
GTI intervals : 30
Total GTI (secs) : 18592.281
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2144.0241699 2144.0241699
20 Percent Complete: Total/live time: 4160.0244141 4160.0244141
30 Percent Complete: Total/live time: 6278.9663086 6278.9663086
40 Percent Complete: Total/live time: 7650.9550781 7650.9550781
50 Percent Complete: Total/live time: 9766.9482422 9766.9482422
60 Percent Complete: Total/live time: 11851.0205078 11851.0205078
70 Percent Complete: Total/live time: 13696.0048828 13696.0048828
80 Percent Complete: Total/live time: 15184.1269531 15184.1269531
90 Percent Complete: Total/live time: 17331.2832031 17331.2832031
100 Percent Complete: Total/live time: 18592.2812500 18592.2812500
Number of attitude steps used: 46
Number of attitude steps avail: 10105
Mean RA/DEC pixel offset: -9.9083 -2.6587
writing expo file: ad71039000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 5015 77 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5092 5015 77 0 0 0
in 18592.28 seconds
Image has 5015 counts for 0.2697 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 2232 77 0 0 2783
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5092 2232 77 0 0 2783
in 18592.28 seconds
Image has 2232 counts for 0.1200 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 2798 77 0 0 2217
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5092 2798 77 0 0 2217
in 18592.28 seconds
Image has 2798 counts for 0.1505 counts/sec
Command not found; type ? for a command listing
!ad71039000g200170m:ASCA >
!ad71039000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000g200170m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000g200170m:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000g200170m:ASCA-GIS2-PH > set image sky
!ad71039000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad71039000g200170m:ASCA-GIS2-PH > extract image
!ad71039000g200170m:ASCA-GIS2-PH > save image outfile=ad71039000g200170m.img
Wrote image to file ad71039000g200170m.img
!ad71039000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad71039000g200170m:ASCA-GIS2-PH > extract image
!ad71039000g200170m:ASCA-GIS2-PH > save image outfile=ad71039000g200170m_lo.img
Wrote image to file ad71039000g200170m_lo.img
!ad71039000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad71039000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71039000g200170m:ASCA-GIS2-PH > extract image
!ad71039000g200170m:ASCA-GIS2-PH > save image outfile=ad71039000g200170m_hi.img
Wrote image to file ad71039000g200170m_hi.img
!ad71039000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad71039000g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad71039000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0548
Mean RA/DEC/ROLL : 196.8514 -23.6645 240.0548
Pnt RA/DEC/ROLL : 196.8809 -23.6668 240.0548
Image rebin factor : 1
Attitude Records : 43391
GTI intervals : 26
Total GTI (secs) : 10480.521
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1608.0070801 1608.0070801
20 Percent Complete: Total/live time: 2359.5048828 2359.5048828
30 Percent Complete: Total/live time: 3884.0949707 3884.0949707
40 Percent Complete: Total/live time: 4774.0922852 4774.0922852
50 Percent Complete: Total/live time: 5475.9458008 5475.9458008
60 Percent Complete: Total/live time: 6557.9423828 6557.9423828
70 Percent Complete: Total/live time: 7464.1186523 7464.1186523
80 Percent Complete: Total/live time: 8494.3115234 8494.3115234
90 Percent Complete: Total/live time: 9557.3085938 9557.3085938
100 Percent Complete: Total/live time: 10480.5195312 10480.5195312
Number of attitude steps used: 28
Number of attitude steps avail: 30032
Mean RA/DEC pixel offset: -9.5546 -2.7112
writing expo file: ad71039000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 2793 47 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2840 2793 47 0 0 0
in 10480.52 seconds
Image has 2793 counts for 0.2665 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 1261 47 0 0 1532
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2840 1261 47 0 0 1532
in 10480.52 seconds
Image has 1261 counts for 0.1203 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 1537 47 0 0 1256
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2840 1537 47 0 0 1256
in 10480.52 seconds
Image has 1537 counts for 0.1467 counts/sec
Command not found; type ? for a command listing
!ad71039000g200270h:ASCA >
!ad71039000g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000g200270h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000g200270h:ASCA > read events ad71039000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000g200270h:ASCA-GIS2-PH > set image sky
!ad71039000g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad71039000g200270h:ASCA-GIS2-PH > extract image
!ad71039000g200270h:ASCA-GIS2-PH > save image outfile=ad71039000g200270h.img
Wrote image to file ad71039000g200270h.img
!ad71039000g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad71039000g200270h:ASCA-GIS2-PH > extract image
!ad71039000g200270h:ASCA-GIS2-PH > save image outfile=ad71039000g200270h_lo.img
Wrote image to file ad71039000g200270h_lo.img
!ad71039000g200270h:ASCA-GIS2-PH > clear pha_cut
!ad71039000g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71039000g200270h:ASCA-GIS2-PH > extract image
!ad71039000g200270h:ASCA-GIS2-PH > save image outfile=ad71039000g200270h_hi.img
Wrote image to file ad71039000g200270h_hi.img
!ad71039000g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad71039000g300170m.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad71039000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0486
Mean RA/DEC/ROLL : 196.8671 -23.6448 240.0486
Pnt RA/DEC/ROLL : 196.8624 -23.6946 240.0486
Image rebin factor : 1
Attitude Records : 43391
GTI intervals : 30
Total GTI (secs) : 18592.281
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2144.0241699 2144.0241699
20 Percent Complete: Total/live time: 4160.0244141 4160.0244141
30 Percent Complete: Total/live time: 6278.9663086 6278.9663086
40 Percent Complete: Total/live time: 7650.9550781 7650.9550781
50 Percent Complete: Total/live time: 9766.9482422 9766.9482422
60 Percent Complete: Total/live time: 11851.0205078 11851.0205078
70 Percent Complete: Total/live time: 13696.0048828 13696.0048828
80 Percent Complete: Total/live time: 15184.1269531 15184.1269531
90 Percent Complete: Total/live time: 17331.2832031 17331.2832031
100 Percent Complete: Total/live time: 18592.2812500 18592.2812500
Number of attitude steps used: 46
Number of attitude steps avail: 10105
Mean RA/DEC pixel offset: 1.9078 -1.4849
writing expo file: ad71039000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 4938 61 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4999 4938 61 0 0 0
in 18592.28 seconds
Image has 4938 counts for 0.2656 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 2234 61 0 0 2704
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4999 2234 61 0 0 2704
in 18592.28 seconds
Image has 2234 counts for 0.1202 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 2727 61 0 0 2211
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4999 2727 61 0 0 2211
in 18592.28 seconds
Image has 2727 counts for 0.1467 counts/sec
Command not found; type ? for a command listing
!ad71039000g300170m:ASCA >
!ad71039000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000g300170m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000g300170m:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000g300170m:ASCA-GIS3-PH > set image sky
!ad71039000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad71039000g300170m:ASCA-GIS3-PH > extract image
!ad71039000g300170m:ASCA-GIS3-PH > save image outfile=ad71039000g300170m.img
Wrote image to file ad71039000g300170m.img
!ad71039000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad71039000g300170m:ASCA-GIS3-PH > extract image
!ad71039000g300170m:ASCA-GIS3-PH > save image outfile=ad71039000g300170m_lo.img
Wrote image to file ad71039000g300170m_lo.img
!ad71039000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad71039000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71039000g300170m:ASCA-GIS3-PH > extract image
!ad71039000g300170m:ASCA-GIS3-PH > save image outfile=ad71039000g300170m_hi.img
Wrote image to file ad71039000g300170m_hi.img
!ad71039000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad71039000g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad71039000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0485
Mean RA/DEC/ROLL : 196.8672 -23.6443 240.0485
Pnt RA/DEC/ROLL : 196.8651 -23.6870 240.0485
Image rebin factor : 1
Attitude Records : 43391
GTI intervals : 25
Total GTI (secs) : 10476.521
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1608.0070801 1608.0070801
20 Percent Complete: Total/live time: 2359.5048828 2359.5048828
30 Percent Complete: Total/live time: 3884.0949707 3884.0949707
40 Percent Complete: Total/live time: 4774.0922852 4774.0922852
50 Percent Complete: Total/live time: 5475.9458008 5475.9458008
60 Percent Complete: Total/live time: 6557.9423828 6557.9423828
70 Percent Complete: Total/live time: 7464.1186523 7464.1186523
80 Percent Complete: Total/live time: 8492.3115234 8492.3115234
90 Percent Complete: Total/live time: 9555.3085938 9555.3085938
100 Percent Complete: Total/live time: 10476.5195312 10476.5195312
Number of attitude steps used: 28
Number of attitude steps avail: 30032
Mean RA/DEC pixel offset: 2.0926 -1.5542
writing expo file: ad71039000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 2822 49 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2871 2822 49 0 0 0
in 10476.52 seconds
Image has 2822 counts for 0.2694 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 1271 49 0 0 1551
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2871 1271 49 0 0 1551
in 10476.52 seconds
Image has 1271 counts for 0.1213 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 1561 49 0 0 1261
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2871 1561 49 0 0 1261
in 10476.52 seconds
Image has 1561 counts for 0.1490 counts/sec
Command not found; type ? for a command listing
!ad71039000g300270h:ASCA >
!ad71039000g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000g300270h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000g300270h:ASCA > read events ad71039000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000g300270h:ASCA-GIS3-PH > set image sky
!ad71039000g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad71039000g300270h:ASCA-GIS3-PH > extract image
!ad71039000g300270h:ASCA-GIS3-PH > save image outfile=ad71039000g300270h.img
Wrote image to file ad71039000g300270h.img
!ad71039000g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad71039000g300270h:ASCA-GIS3-PH > extract image
!ad71039000g300270h:ASCA-GIS3-PH > save image outfile=ad71039000g300270h_lo.img
Wrote image to file ad71039000g300270h_lo.img
!ad71039000g300270h:ASCA-GIS3-PH > clear pha_cut
!ad71039000g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71039000g300270h:ASCA-GIS3-PH > extract image
!ad71039000g300270h:ASCA-GIS3-PH > save image outfile=ad71039000g300270h_hi.img
Wrote image to file ad71039000g300270h_hi.img
!ad71039000g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad71039000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad71039000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0575
Mean RA/DEC/ROLL : 196.8448 -23.6469 240.0575
Pnt RA/DEC/ROLL : 196.8877 -23.6873 240.0575
Image rebin factor : 4
Attitude Records : 43391
Hot Pixels : 144
GTI intervals : 32
Total GTI (secs) : 9006.173
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1244.0072021 1244.0072021
20 Percent Complete: Total/live time: 1938.3859863 1938.3859863
30 Percent Complete: Total/live time: 2859.9448242 2859.9448242
40 Percent Complete: Total/live time: 3716.4108887 3716.4108887
50 Percent Complete: Total/live time: 5289.6367188 5289.6367188
60 Percent Complete: Total/live time: 6281.6367188 6281.6367188
70 Percent Complete: Total/live time: 7183.9936523 7183.9936523
80 Percent Complete: Total/live time: 7435.7861328 7435.7861328
90 Percent Complete: Total/live time: 8296.7832031 8296.7832031
100 Percent Complete: Total/live time: 9006.1728516 9006.1728516
Number of attitude steps used: 28
Number of attitude steps avail: 29783
Mean RA/DEC pixel offset: -34.2919 -86.5376
writing expo file: ad71039000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 998 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
998 998 0 0 0 0
in 9006.17 seconds
Image has 998 counts for 0.1108 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 551 0 0 0 447
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
998 551 0 0 0 447
in 9006.17 seconds
Image has 551 counts for 6.1180E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 448 0 0 0 550
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
998 448 0 0 0 550
in 9006.17 seconds
Image has 448 counts for 4.9744E-02 counts/sec
Command not found; type ? for a command listing
!ad71039000s000102h:ASCA >
!ad71039000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000s000102h:ASCA > read events ad71039000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad71039000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad71039000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000102h.img
Wrote image to file ad71039000s000102h.img
!ad71039000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad71039000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000102h_lo.img
Wrote image to file ad71039000s000102h_lo.img
!ad71039000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad71039000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71039000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000102h_hi.img
Wrote image to file ad71039000s000102h_hi.img
!ad71039000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad71039000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad71039000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0575
Mean RA/DEC/ROLL : 196.8453 -23.6466 240.0575
Pnt RA/DEC/ROLL : 196.8864 -23.6950 240.0575
Image rebin factor : 4
Attitude Records : 43391
Hot Pixels : 108
GTI intervals : 28
Total GTI (secs) : 17616.678
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2139.4929199 2139.4929199
20 Percent Complete: Total/live time: 4539.4926758 4539.4926758
30 Percent Complete: Total/live time: 5862.4365234 5862.4365234
40 Percent Complete: Total/live time: 7547.4926758 7547.4926758
50 Percent Complete: Total/live time: 9022.4179688 9022.4179688
60 Percent Complete: Total/live time: 11174.4892578 11174.4892578
70 Percent Complete: Total/live time: 12877.2226562 12877.2226562
80 Percent Complete: Total/live time: 14334.9580078 14334.9580078
90 Percent Complete: Total/live time: 16381.9433594 16381.9433594
100 Percent Complete: Total/live time: 17616.6757812 17616.6757812
Number of attitude steps used: 45
Number of attitude steps avail: 8908
Mean RA/DEC pixel offset: -36.6606 -86.0735
writing expo file: ad71039000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2021 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 2021 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2021 2021 0 0 0 0
in 17616.68 seconds
Image has 2021 counts for 0.1147 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 951 0 0 0 1070
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2021 951 0 0 0 1070
in 17616.68 seconds
Image has 951 counts for 5.3983E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 1071 0 0 0 950
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2021 1071 0 0 0 950
in 17616.68 seconds
Image has 1071 counts for 6.0795E-02 counts/sec
Command not found; type ? for a command listing
!ad71039000s000202m:ASCA >
!ad71039000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000s000202m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000s000202m:ASCA > read events ad71039000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad71039000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad71039000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000202m.img
Wrote image to file ad71039000s000202m.img
!ad71039000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad71039000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000202m_lo.img
Wrote image to file ad71039000s000202m_lo.img
!ad71039000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad71039000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71039000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad71039000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad71039000s000202m_hi.img
Wrote image to file ad71039000s000202m_hi.img
!ad71039000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad71039000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad71039000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0516
Mean RA/DEC/ROLL : 196.8593 -23.6556 240.0516
Pnt RA/DEC/ROLL : 196.8732 -23.6786 240.0516
Image rebin factor : 4
Attitude Records : 43391
Hot Pixels : 166
GTI intervals : 31
Total GTI (secs) : 8954.908
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1212.0072021 1212.0072021
20 Percent Complete: Total/live time: 1964.4423828 1964.4423828
30 Percent Complete: Total/live time: 2788.1235352 2788.1235352
40 Percent Complete: Total/live time: 4168.2006836 4168.2006836
50 Percent Complete: Total/live time: 5146.1660156 5146.1660156
60 Percent Complete: Total/live time: 6170.1660156 6170.1660156
70 Percent Complete: Total/live time: 7076.5229492 7076.5229492
80 Percent Complete: Total/live time: 7352.5219727 7352.5219727
90 Percent Complete: Total/live time: 8245.5195312 8245.5195312
100 Percent Complete: Total/live time: 8954.9091797 8954.9091797
Number of attitude steps used: 26
Number of attitude steps avail: 29989
Mean RA/DEC pixel offset: -38.7401 -17.0953
writing expo file: ad71039000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 1143 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1143 1143 0 0 0 0
in 8954.91 seconds
Image has 1143 counts for 0.1276 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 638 0 0 0 505
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1143 638 0 0 0 505
in 8954.91 seconds
Image has 638 counts for 7.1246E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 505 0 0 0 638
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1143 505 0 0 0 638
in 8954.91 seconds
Image has 505 counts for 5.6394E-02 counts/sec
Command not found; type ? for a command listing
!ad71039000s100102h:ASCA >
!ad71039000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000s100102h:ASCA > read events ad71039000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad71039000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad71039000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100102h.img
Wrote image to file ad71039000s100102h.img
!ad71039000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad71039000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100102h_lo.img
Wrote image to file ad71039000s100102h_lo.img
!ad71039000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad71039000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71039000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100102h_hi.img
Wrote image to file ad71039000s100102h_hi.img
!ad71039000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad71039000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad71039000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0517
Mean RA/DEC/ROLL : 196.8597 -23.6554 240.0517
Pnt RA/DEC/ROLL : 196.8719 -23.6863 240.0517
Image rebin factor : 4
Attitude Records : 43391
Hot Pixels : 98
GTI intervals : 28
Total GTI (secs) : 17680.678
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2171.4931641 2171.4931641
20 Percent Complete: Total/live time: 4990.4394531 4990.4394531
30 Percent Complete: Total/live time: 6238.4360352 6238.4360352
40 Percent Complete: Total/live time: 7611.4931641 7611.4931641
50 Percent Complete: Total/live time: 9339.4931641 9339.4931641
60 Percent Complete: Total/live time: 11378.4902344 11378.4902344
70 Percent Complete: Total/live time: 12941.2246094 12941.2246094
80 Percent Complete: Total/live time: 14398.9599609 14398.9599609
90 Percent Complete: Total/live time: 16445.9453125 16445.9453125
100 Percent Complete: Total/live time: 17680.6777344 17680.6777344
Number of attitude steps used: 39
Number of attitude steps avail: 9157
Mean RA/DEC pixel offset: -40.8998 -15.8472
writing expo file: ad71039000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 2206 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2206 2206 0 0 0 0
in 17680.68 seconds
Image has 2206 counts for 0.1248 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 1004 0 0 0 1202
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2206 1004 0 0 0 1202
in 17680.68 seconds
Image has 1004 counts for 5.6785E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 1204 0 0 0 1002
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2206 1204 0 0 0 1002
in 17680.68 seconds
Image has 1204 counts for 6.8097E-02 counts/sec
Command not found; type ? for a command listing
!ad71039000s100202m:ASCA >
!ad71039000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000s100202m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000s100202m:ASCA > read events ad71039000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad71039000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad71039000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100202m.img
Wrote image to file ad71039000s100202m.img
!ad71039000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad71039000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100202m_lo.img
Wrote image to file ad71039000s100202m_lo.img
!ad71039000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad71039000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71039000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100202m_hi.img
Wrote image to file ad71039000s100202m_hi.img
!ad71039000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad71039000s100402m.expo
ASCAEXPO_V0.9b
reading data file: ad71039000s100402m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940201_0315.2340
making an exposure map...
Aspect RA/DEC/ROLL : 196.8680 -23.6501 240.0516
Mean RA/DEC/ROLL : 196.8599 -23.6552 240.0516
Pnt RA/DEC/ROLL : 196.8791 -23.6427 240.0516
Image rebin factor : 4
Attitude Records : 43391
Hot Pixels : 46
GTI intervals : 4
Total GTI (secs) : 37.236
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 31.6925526 31.6925526
20 Percent Complete: Total/live time: 31.6925526 31.6925526
30 Percent Complete: Total/live time: 37.2359848 37.2359848
100 Percent Complete: Total/live time: 37.2359848 37.2359848
Number of attitude steps used: 4
Number of attitude steps avail: 995
Mean RA/DEC pixel offset: -28.4045 -14.3862
writing expo file: ad71039000s100402m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71039000s100402m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71039000s100402m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 50 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50 50 0 0 0 0
in 37.24 seconds
Image has 50 counts for 1.343 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 50 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50 50 0 0 0 0
in 37.24 seconds
Image has 50 counts for 1.343 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 0 0 0 0 50
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50 0 0 0 0 50
in 37.24 seconds
Image has 0 counts for 0. counts/sec
Command not found; type ? for a command listing
!ad71039000s100402m:ASCA >
!ad71039000s100402m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71039000s100402m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!ad71039000s100402m:ASCA > read events ad71039000s100402m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!ad71039000s100402m:ASCA-SIS1-BRIGHT > set image sky
!ad71039000s100402m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad71039000s100402m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100402m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100402m.img
Wrote image to file ad71039000s100402m.img
!ad71039000s100402m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad71039000s100402m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100402m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100402m_lo.img
Wrote image to file ad71039000s100402m_lo.img
!ad71039000s100402m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad71039000s100402m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71039000s100402m:ASCA-SIS1-BRIGHT > extract image
!ad71039000s100402m:ASCA-SIS1-BRIGHT > save image outfile=ad71039000s100402m_hi.img
Wrote image to file ad71039000s100402m_hi.img
!ad71039000s100402m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad71039000s000102h.expo ad71039000s000202m.expo ad71039000s100102h.expo ad71039000s100202m.expo ad71039000s100402m.expo-> Summing the following images to produce ad71039000sis32002_all.totsky
ad71039000s000102h.img ad71039000s000202m.img ad71039000s100102h.img ad71039000s100202m.img ad71039000s100402m.img-> Summing the following images to produce ad71039000sis32002_lo.totsky
ad71039000s000102h_lo.img ad71039000s000202m_lo.img ad71039000s100102h_lo.img ad71039000s100202m_lo.img ad71039000s100402m_lo.img-> Summing the following images to produce ad71039000sis32002_hi.totsky
ad71039000s000102h_hi.img ad71039000s000202m_hi.img ad71039000s100102h_hi.img ad71039000s100202m_hi.img ad71039000s100402m_hi.img-> Running XIMAGE to create ad71039000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad71039000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad71039000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 888.261 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 888 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 22.0000 22 0 ![9]XIMAGE> exit-> Summing gis images
ad71039000g200170m.expo ad71039000g200270h.expo ad71039000g300170m.expo ad71039000g300270h.expo-> Summing the following images to produce ad71039000gis25670_all.totsky
ad71039000g200170m.img ad71039000g200270h.img ad71039000g300170m.img ad71039000g300270h.img-> Summing the following images to produce ad71039000gis25670_lo.totsky
ad71039000g200170m_lo.img ad71039000g200270h_lo.img ad71039000g300170m_lo.img ad71039000g300270h_lo.img-> Summing the following images to produce ad71039000gis25670_hi.totsky
ad71039000g200170m_hi.img ad71039000g200270h_hi.img ad71039000g300170m_hi.img ad71039000g300270h_hi.img-> Running XIMAGE to create ad71039000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad71039000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 7.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 7 min: 0 ![2]XIMAGE> read/exp_map ad71039000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 969.027 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 969 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 5.00000 50 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 25.0000 25 0 ![9]XIMAGE> exit
94 92 4.19665e-05 20 6 4.09084-> Smoothing ad71039000gis25670_hi.totsky with ad71039000gis25670.totexpo
147 120 2.35175e-05 41 6 4.14961-> Smoothing ad71039000gis25670_lo.totsky with ad71039000gis25670.totexpo
95 91 1.79014e-05 20 8 4.09082-> Determining extraction radii
94 92 20 F 147 120 24 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad71039000gis25670.src
200 142 8.84392e-06 24 10 4.27092-> Determining extraction radii
200 142 24 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad71039000sis32002.src
The sum of the selected column is 958.00000 The mean of the selected column is 479.00000 The standard deviation of the selected column is 5.6568542 The minimum of selected column is 475.00000 The maximum of selected column is 483.00000 The number of points used in calculation is 2-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 994.00000 The mean of the selected column is 497.00000 The standard deviation of the selected column is 0. The minimum of selected column is 497.00000 The maximum of selected column is 497.00000 The number of points used in calculation is 2-> Converting (800.0,568.0,2.0) to s1 detector coordinates
The sum of the selected column is 21038.000 The mean of the selected column is 478.13636 The standard deviation of the selected column is 12.459406 The minimum of selected column is 459.00000 The maximum of selected column is 498.00000 The number of points used in calculation is 44-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 23524.000 The mean of the selected column is 534.63636 The standard deviation of the selected column is 11.452817 The minimum of selected column is 515.00000 The maximum of selected column is 554.00000 The number of points used in calculation is 44-> Converting (94.0,92.0,2.0) to g2 detector coordinates
The sum of the selected column is 984.00000 The mean of the selected column is 109.33333 The standard deviation of the selected column is 1.0000000 The minimum of selected column is 108.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 9-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1589.0000 The mean of the selected column is 176.55556 The standard deviation of the selected column is 1.2360331 The minimum of selected column is 174.00000 The maximum of selected column is 178.00000 The number of points used in calculation is 9-> Converting (147.0,120.0,2.0) to g2 detector coordinates
The sum of the selected column is 1501.0000 The mean of the selected column is 107.21429 The standard deviation of the selected column is 1.3114039 The minimum of selected column is 105.00000 The maximum of selected column is 109.00000 The number of points used in calculation is 14-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1638.0000 The mean of the selected column is 117.00000 The standard deviation of the selected column is 0.87705802 The minimum of selected column is 115.00000 The maximum of selected column is 118.00000 The number of points used in calculation is 14-> Converting (94.0,92.0,2.0) to g3 detector coordinates
The sum of the selected column is 2537.0000 The mean of the selected column is 115.31818 The standard deviation of the selected column is 0.99457402 The minimum of selected column is 114.00000 The maximum of selected column is 118.00000 The number of points used in calculation is 22-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3891.0000 The mean of the selected column is 176.86364 The standard deviation of the selected column is 1.2834275 The minimum of selected column is 175.00000 The maximum of selected column is 179.00000 The number of points used in calculation is 22-> Converting (147.0,120.0,2.0) to g3 detector coordinates
The sum of the selected column is 1586.0000 The mean of the selected column is 113.28571 The standard deviation of the selected column is 0.91387353 The minimum of selected column is 112.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 14-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1631.0000 The mean of the selected column is 116.50000 The standard deviation of the selected column is 1.0919284 The minimum of selected column is 115.00000 The maximum of selected column is 119.00000 The number of points used in calculation is 14
1 ad71039000s000102h.evt 3019 1 ad71039000s000202m.evt 3019-> Fetching SIS0_NOTCHIP2.1
ad71039000s000102h.evt ad71039000s000202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2021 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 95 903 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 192 1829 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3019 287 2732 0 0 0
in 26622.85 seconds
Spectrum has 287 counts for 1.0780E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 26623. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.85645E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 95 903 0 0 0
Writing events file
95 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 192 1829 0 0 0
Writing events file
287 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3019 287 2732 0 0 0
in 26622.85 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad71039000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad71039000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad71039000s010102_1.pi group=yes
Wrote spectrum to ad71039000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71039000s010102_1.pi since it has 287 events1 ad71039000s000112h.evt 1068-> SIS0_NOTCHIP2.1 already present in current directory
ad71039000s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.90E+04 1068 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000112h.evt
Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
in 9006.17 seconds
Spectrum has 101 counts for 1.1215E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 9006.2 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.85645E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000s010212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000112h.evt
Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
Writing events file
101 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
in 9006.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71039000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad71039000s010212_1.pi group=yes
Wrote spectrum to ad71039000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s010212_1.pi since it has 101 events1 ad71039000s100102h.evt 3399 1 ad71039000s100202m.evt 3399 1 ad71039000s100402m.evt 3399-> Fetching SIS1_NOTCHIP0.1
ad71039000s100102h.evt ad71039000s100202m.evt ad71039000s100402m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
3 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 129 1014 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 230 1976 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3399 360 3039 0 0 0
in 26672.82 seconds
Spectrum has 360 counts for 1.3497E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 26673. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.82910E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 129 1014 0 0 0
Writing events file
129 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 230 1976 0 0 0
Writing events file
359 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
Writing events file
360 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3399 360 3039 0 0 0
in 26672.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad71039000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad71039000s100402m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad71039000s110102_1.pi group=yes
Wrote spectrum to ad71039000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71039000s110102_1.pi since it has 360 events1 ad71039000s100112h.evt 1254 1 ad71039000s100412m.evt 1254-> SIS1_NOTCHIP0.1 already present in current directory
ad71039000s100112h.evt ad71039000s100412m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.90E+04 1204 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.90E+04 1204 0011
2 NGC4968 BRIGHT2 MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100112h.evt
Total Good Bad: Region Time Phase Cut
1204 131 1073 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100412m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1254 132 1122 0 0 0
in 8992.15 seconds
Spectrum has 132 counts for 1.4679E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 8992.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.82910E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000s110212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100112h.evt
Total Good Bad: Region Time Phase Cut
1204 131 1073 0 0 0
Writing events file
131 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100412m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
Writing events file
132 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1254 132 1122 0 0 0
in 8992.15 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad71039000s100412m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71039000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad71039000s110212_1.pi group=yes
Wrote spectrum to ad71039000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s110212_1.pi since it has 132 events1 ad71039000g200170m.evt 7932 1 ad71039000g200270h.evt 7932-> GIS2_REGION256.4 already present in current directory
ad71039000g200170m.evt ad71039000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 347 4745 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 184 2656 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7932 531 7401 0 0 0
in 29072.80 seconds
Spectrum has 531 counts for 1.8264E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29073. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.05231E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > read events ad71039000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad71039000g210170_1.pi group=yes
Wrote spectrum to ad71039000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad71039000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad71039000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29073. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.05231E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 65 are grouped by a factor 66 ... 66 - 88 are grouped by a factor 23 ... 89 - 109 are grouped by a factor 21 ... 110 - 133 are grouped by a factor 24 ... 134 - 152 are grouped by a factor 19 ... 153 - 175 are grouped by a factor 23 ... 176 - 205 are grouped by a factor 30 ... 206 - 258 are grouped by a factor 53 ... 259 - 306 are grouped by a factor 48 ... 307 - 381 are grouped by a factor 75 ... 382 - 502 are grouped by a factor 121 ... --------------------------------------------- ... ...... exiting, changes written to file : ad71039000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 41 by 41 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 79 147
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 81.116 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 109.00 177.00 (detector coordinates)
Point source at 24.00 -46.04 (WMAP bins wrt optical axis)
Point source at 12.75 297.53 (... in polar coordinates)
Total counts in region = 5.31000E+02
Weighted mean angle from optical axis = 13.215 arcmin
-> Extracting ad71039000g210170_2.pi from ad71039000g225670_2.reg and:ad71039000g200170m.evt ad71039000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 393 4699 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 230 2610 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7932 623 7309 0 0 0
in 29072.80 seconds
Spectrum has 623 counts for 2.1429E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29073. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g210170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > read events ad71039000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad71039000g210170_2.pi group=yes
Wrote spectrum to ad71039000g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad71039000g210170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad71039000g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29073. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 68 are grouped by a factor 69 ... 69 - 85 are grouped by a factor 17 ... 86 - 107 are grouped by a factor 22 ... 108 - 126 are grouped by a factor 19 ... 127 - 148 are grouped by a factor 22 ... 149 - 171 are grouped by a factor 23 ... 172 - 198 are grouped by a factor 27 ... 199 - 232 are grouped by a factor 34 ... 233 - 275 are grouped by a factor 43 ... 276 - 323 are grouped by a factor 48 ... 324 - 368 are grouped by a factor 45 ... 369 - 435 are grouped by a factor 67 ... 436 - 540 are grouped by a factor 105 ... 541 - 638 are grouped by a factor 98 ... 639 - 854 are grouped by a factor 216 ... 855 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad71039000g210170_2.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 45 55
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 107.00 117.00 (detector coordinates)
Point source at 26.00 13.96 (WMAP bins wrt optical axis)
Point source at 7.25 28.23 (... in polar coordinates)
Total counts in region = 6.23000E+02
Weighted mean angle from optical axis = 7.540 arcmin
-> Standard Output From STOOL group_event_files:1 ad71039000g300170m.evt 7870 1 ad71039000g300270h.evt 7870-> GIS3_REGION256.4 already present in current directory
ad71039000g300170m.evt ad71039000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 375 4624 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 220 2651 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7870 595 7275 0 0 0
in 29068.80 seconds
Spectrum has 595 counts for 2.0469E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29069. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.05231E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > read events ad71039000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad71039000g310170_1.pi group=yes
Wrote spectrum to ad71039000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad71039000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad71039000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29069. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.05231E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 46 are grouped by a factor 47 ... 47 - 73 are grouped by a factor 27 ... 74 - 92 are grouped by a factor 19 ... 93 - 110 are grouped by a factor 18 ... 111 - 125 are grouped by a factor 15 ... 126 - 150 are grouped by a factor 25 ... 151 - 168 are grouped by a factor 18 ... 169 - 187 are grouped by a factor 19 ... 188 - 228 are grouped by a factor 41 ... 229 - 277 are grouped by a factor 49 ... 278 - 315 are grouped by a factor 38 ... 316 - 387 are grouped by a factor 72 ... 388 - 527 are grouped by a factor 140 ... 528 - 722 are grouped by a factor 195 ... 723 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad71039000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 41 by 41 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 85 147
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 81.116 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 115.00 177.00 (detector coordinates)
Point source at 4.36 -42.56 (WMAP bins wrt optical axis)
Point source at 10.51 275.85 (... in polar coordinates)
Total counts in region = 5.95000E+02
Weighted mean angle from optical axis = 10.852 arcmin
-> Extracting ad71039000g310170_2.pi from ad71039000g325670_2.reg and:ad71039000g300170m.evt ad71039000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 435 4564 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 257 2614 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7870 692 7178 0 0 0
in 29068.80 seconds
Spectrum has 692 counts for 2.3806E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 29069. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g310170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > read events ad71039000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad71039000g310170_2.pi group=yes
Wrote spectrum to ad71039000g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad71039000g310170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad71039000g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 29069. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 64 are grouped by a factor 65 ... 65 - 90 are grouped by a factor 26 ... 91 - 110 are grouped by a factor 20 ... 111 - 128 are grouped by a factor 18 ... 129 - 145 are grouped by a factor 17 ... 146 - 163 are grouped by a factor 18 ... 164 - 185 are grouped by a factor 22 ... 186 - 217 are grouped by a factor 32 ... 218 - 263 are grouped by a factor 46 ... 264 - 294 are grouped by a factor 31 ... 295 - 353 are grouped by a factor 59 ... 354 - 415 are grouped by a factor 62 ... 416 - 493 are grouped by a factor 78 ... 494 - 544 are grouped by a factor 51 ... 545 - 674 are grouped by a factor 130 ... 675 - 813 are grouped by a factor 139 ... 814 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad71039000g310170_2.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 51 55
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 113.00 117.00 (detector coordinates)
Point source at 6.36 17.44 (WMAP bins wrt optical axis)
Point source at 4.56 69.96 (... in polar coordinates)
Total counts in region = 6.92000E+02
Weighted mean angle from optical axis = 5.484 arcmin
-> Plotting ad71039000g210170_1_pi.ps from ad71039000g210170_1.pi
XSPEC 9.01 02:02:55 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad71039000g210170_1.pi
Net count rate (cts/s) for file 1 1.8264E-02+/- 7.9261E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad71039000g210170_2_pi.ps from ad71039000g210170_2.pi
XSPEC 9.01 02:03:07 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad71039000g210170_2.pi
Net count rate (cts/s) for file 1 2.1429E-02+/- 9.6064E-04
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad71039000g310170_1_pi.ps from ad71039000g310170_1.pi
XSPEC 9.01 02:03:18 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad71039000g310170_1.pi
Net count rate (cts/s) for file 1 2.0469E-02+/- 1.0153E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad71039000g310170_2_pi.ps from ad71039000g310170_2.pi
XSPEC 9.01 02:03:28 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad71039000g310170_2.pi
Net count rate (cts/s) for file 1 2.3806E-02+/- 1.0141E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2021 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 95 903 0 0 0
Writing events file
95 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 192 1829 0 0 0
Writing events file
287 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3019 287 2732 0 0 0
in 26622.85 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad71039000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> skipping ad71039000s000002_1.lc since it would have 287 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
2 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
3 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 130 1013 0 0 0
Writing events file
130 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 234 1972 0 0 0
Writing events file
364 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
Writing events file
365 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3399 365 3034 0 0 0
in 26672.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad71039000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad71039000s100402m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> skipping ad71039000s100002_1.lc since it would have 365 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 347 4745 0 0 0
Writing events file
347 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 184 2656 0 0 0
Writing events file
531 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7932 531 7401 0 0 0
in 29072.80 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > read events ad71039000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad71039000g200070_1.lc with binsize 2737.55166492795
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:16:02 0.29E+05 531 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/events.tmp
Total Good Bad: Region Time Phase Cut
531 531 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
531 531 0 0 0 0
in 29072.80 seconds
Fits light curve has 531 counts for 1.8264E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > set binsize 2737.55166492795
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad71039000g200070_1.lc
Wrote FITS light curve to file ad71039000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad71039000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71039000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC4968 Start Time (d) .... 9384 03:56:10.615
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9384 23:34:34.622
No. of Rows ....... 12 Bin Time (s) ...... 2738.
Right Ascension ... 1.9687E+02 Internal time sys.. Converted to TJD
Declination ....... -2.3650E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 26 Newbins of 2737.55 (s)
Intv 1 Start 9384 4:18:59
Ser.1 Avg 0.1859E-01 Chisq 16.41 Var 0.1442E-04 Newbs. 12
Min 0.1402E-01 Max 0.2895E-01expVar 0.1054E-04 Bins 12
Results from Statistical Analysis
Newbin Integration Time (s).. 2737.6
Interval Duration (s)........ 68439.
No. of Newbins .............. 12
Average (c/s) ............... 0.18585E-01 +/- 0.98E-03
Standard Deviation (c/s)..... 0.37967E-02
Minimum (c/s)................ 0.14024E-01
Maximum (c/s)................ 0.28947E-01
Variance ((c/s)**2).......... 0.14415E-04 +/- 0.61E-05
Expected Variance ((c/s)**2). 0.10541E-04 +/- 0.45E-05
Third Moment ((c/s)**3)...... 0.78724E-07
Average Deviation (c/s)...... 0.27698E-02
Skewness..................... 1.4384 +/- 0.71
Kurtosis..................... 1.9662 +/- 1.4
RMS fractional variation....< 0.20675 (3 sigma)
Chi-Square................... 16.411 dof 11
Chi-Square Prob of constancy. 0.12657 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.27728 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 26 Newbins of 2737.55 (s)
Intv 1 Start 9384 4:18:59
Ser.1 Avg 0.1859E-01 Chisq 16.41 Var 0.1442E-04 Newbs. 12
Min 0.1402E-01 Max 0.2895E-01expVar 0.1054E-04 Bins 12
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad71039000g225670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 393 4699 0 0 0
Writing events file
393 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 230 2610 0 0 0
Writing events file
623 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7932 623 7309 0 0 0
in 29072.80 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > read events ad71039000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad71039000g200070_2.lc with binsize 2333.2904238792
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:16:02 0.29E+05 623 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/events.tmp
Total Good Bad: Region Time Phase Cut
623 623 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
623 623 0 0 0 0
in 29072.80 seconds
Fits light curve has 623 counts for 2.1429E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > set binsize 2333.2904238792
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad71039000g200070_2.lc
Wrote FITS light curve to file ad71039000g200070_2.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad71039000g200070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71039000g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC4968 Start Time (d) .... 9384 03:56:10.615
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9384 23:34:34.622
No. of Rows ....... 13 Bin Time (s) ...... 2333.
Right Ascension ... 1.9687E+02 Internal time sys.. Converted to TJD
Declination ....... -2.3650E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 31 Newbins of 2333.29 (s)
Intv 1 Start 9384 4:15:37
Ser.1 Avg 0.2035E-01 Chisq 5.615 Var 0.5458E-05 Newbs. 13
Min 0.1552E-01 Max 0.2444E-01expVar 0.1264E-04 Bins 13
Results from Statistical Analysis
Newbin Integration Time (s).. 2333.3
Interval Duration (s)........ 67665.
No. of Newbins .............. 13
Average (c/s) ............... 0.20351E-01 +/- 0.10E-02
Standard Deviation (c/s)..... 0.23362E-02
Minimum (c/s)................ 0.15522E-01
Maximum (c/s)................ 0.24440E-01
Variance ((c/s)**2).......... 0.54579E-05 +/- 0.22E-05
Expected Variance ((c/s)**2). 0.12636E-04 +/- 0.52E-05
Third Moment ((c/s)**3)......-0.17378E-08
Average Deviation (c/s)...... 0.16989E-02
Skewness.....................-0.13629 +/- 0.68
Kurtosis.....................-0.16375 +/- 1.4
RMS fractional variation....< 0.26146 (3 sigma)
Chi-Square................... 5.6153 dof 12
Chi-Square Prob of constancy. 0.93421 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.48280 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 31 Newbins of 2333.29 (s)
Intv 1 Start 9384 4:15:37
Ser.1 Avg 0.2035E-01 Chisq 5.615 Var 0.5458E-05 Newbs. 13
Min 0.1552E-01 Max 0.2444E-01expVar 0.1264E-04 Bins 13
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad71039000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 375 4624 0 0 0
Writing events file
375 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 220 2651 0 0 0
Writing events file
595 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7870 595 7275 0 0 0
in 29068.80 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > read events ad71039000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad71039000g300070_1.lc with binsize 2442.75619221648
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:16:02 0.29E+05 595 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/events.tmp
Total Good Bad: Region Time Phase Cut
595 595 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
595 595 0 0 0 0
in 29068.80 seconds
Fits light curve has 595 counts for 2.0469E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > set binsize 2442.75619221648
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad71039000g300070_1.lc
Wrote FITS light curve to file ad71039000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad71039000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71039000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC4968 Start Time (d) .... 9384 03:56:10.615
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9384 23:34:34.622
No. of Rows ....... 13 Bin Time (s) ...... 2443.
Right Ascension ... 1.9687E+02 Internal time sys.. Converted to TJD
Declination ....... -2.3650E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 29 Newbins of 2442.76 (s)
Intv 1 Start 9384 4:16:31
Ser.1 Avg 0.2058E-01 Chisq 11.26 Var 0.1072E-04 Newbs. 13
Min 0.1597E-01 Max 0.2758E-01expVar 0.1238E-04 Bins 13
Results from Statistical Analysis
Newbin Integration Time (s).. 2442.8
Interval Duration (s)........ 68397.
No. of Newbins .............. 13
Average (c/s) ............... 0.20578E-01 +/- 0.10E-02
Standard Deviation (c/s)..... 0.32747E-02
Minimum (c/s)................ 0.15969E-01
Maximum (c/s)................ 0.27577E-01
Variance ((c/s)**2).......... 0.10724E-04 +/- 0.44E-05
Expected Variance ((c/s)**2). 0.12383E-04 +/- 0.51E-05
Third Moment ((c/s)**3)...... 0.20211E-07
Average Deviation (c/s)...... 0.26617E-02
Skewness..................... 0.57553 +/- 0.68
Kurtosis.....................-0.46010 +/- 1.4
RMS fractional variation....< 0.22986 (3 sigma)
Chi-Square................... 11.258 dof 12
Chi-Square Prob of constancy. 0.50688 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.12446 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 29 Newbins of 2442.76 (s)
Intv 1 Start 9384 4:16:31
Ser.1 Avg 0.2058E-01 Chisq 11.26 Var 0.1072E-04 Newbs. 13
Min 0.1597E-01 Max 0.2758E-01expVar 0.1238E-04 Bins 13
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad71039000g325670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 435 4564 0 0 0
Writing events file
435 events written to the output file
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 257 2614 0 0 0
Writing events file
692 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7870 692 7178 0 0 0
in 29068.80 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > read events ad71039000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad71039000g300070_2.lc with binsize 2100.34672596648
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:16:02 0.29E+05 692 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/events.tmp
Total Good Bad: Region Time Phase Cut
692 692 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
692 692 0 0 0 0
in 29068.80 seconds
Fits light curve has 692 counts for 2.3806E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > set binsize 2100.34672596648
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad71039000g300070_2.lc
Wrote FITS light curve to file ad71039000g300070_2.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad71039000g300070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71039000g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC4968 Start Time (d) .... 9384 03:56:10.615
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9384 23:34:34.622
No. of Rows ....... 15 Bin Time (s) ...... 2100.
Right Ascension ... 1.9687E+02 Internal time sys.. Converted to TJD
Declination ....... -2.3650E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 34 Newbins of 2100.35 (s)
Intv 1 Start 9384 4:13:40
Ser.1 Avg 0.2312E-01 Chisq 7.279 Var 0.7594E-05 Newbs. 15
Min 0.1825E-01 Max 0.2809E-01expVar 0.1565E-04 Bins 15
Results from Statistical Analysis
Newbin Integration Time (s).. 2100.3
Interval Duration (s)........ 69311.
No. of Newbins .............. 15
Average (c/s) ............... 0.23119E-01 +/- 0.11E-02
Standard Deviation (c/s)..... 0.27557E-02
Minimum (c/s)................ 0.18254E-01
Maximum (c/s)................ 0.28089E-01
Variance ((c/s)**2).......... 0.75939E-05 +/- 0.29E-05
Expected Variance ((c/s)**2). 0.15648E-04 +/- 0.59E-05
Third Moment ((c/s)**3)...... 0.12166E-07
Average Deviation (c/s)...... 0.21419E-02
Skewness..................... 0.58138 +/- 0.63
Kurtosis.....................-0.38124 +/- 1.3
RMS fractional variation....< 0.24382 (3 sigma)
Chi-Square................... 7.2793 dof 14
Chi-Square Prob of constancy. 0.92340 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.58550 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 34 Newbins of 2100.35 (s)
Intv 1 Start 9384 4:13:40
Ser.1 Avg 0.2312E-01 Chisq 7.279 Var 0.7594E-05 Newbs. 15
Min 0.1825E-01 Max 0.2809E-01expVar 0.1565E-04 Bins 15
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad71039000g200170m.evt[2] ad71039000g200270h.evt[2]-> Making L1 light curve of ft940201_0315_2340G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 20875 output records from 20901 good input G2_L1 records.-> Making L1 light curve of ft940201_0315_2340G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 26193 output records from 37736 good input G2_L1 records.-> Merging GTIs from the following files:
ad71039000g300170m.evt[2] ad71039000g300270h.evt[2]-> Making L1 light curve of ft940201_0315_2340G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 19716 output records from 19741 good input G3_L1 records.-> Making L1 light curve of ft940201_0315_2340G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 25625 output records from 36184 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 347 4745 0 0 0
Writing events file
347 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5092 347 4745 0 0 0
in 18592.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71039000g200170m_1.ulc use_events=yes
Wrote events list to file ad71039000g200170m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g200170m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 5092 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.evt
Total Good Bad: Region Time Phase Cut
5092 393 4699 0 0 0
Writing events file
393 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5092 393 4699 0 0 0
in 18592.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71039000g200170m_2.ulc use_events=yes
Wrote events list to file ad71039000g200170m_2.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 184 2656 0 0 0
Writing events file
184 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2840 184 2656 0 0 0
in 10480.52 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71039000g200270h_1.ulc use_events=yes
Wrote events list to file ad71039000g200270h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g200270h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2840 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.evt
Total Good Bad: Region Time Phase Cut
2840 230 2610 0 0 0
Writing events file
230 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2840 230 2610 0 0 0
in 10480.52 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region ad71039000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71039000g200270h_2.ulc use_events=yes
Wrote events list to file ad71039000g200270h_2.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g300170m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 375 4624 0 0 0
Writing events file
375 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4999 375 4624 0 0 0
in 18592.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71039000g300170m_1.ulc use_events=yes
Wrote events list to file ad71039000g300170m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g300170m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.19E+05 4999 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.evt
Total Good Bad: Region Time Phase Cut
4999 435 4564 0 0 0
Writing events file
435 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4999 435 4564 0 0 0
in 18592.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71039000g300170m_2.ulc use_events=yes
Wrote events list to file ad71039000g300170m_2.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 220 2651 0 0 0
Writing events file
220 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2871 220 2651 0 0 0
in 10476.52 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71039000g300270h_1.ulc use_events=yes
Wrote events list to file ad71039000g300270h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000g300270h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.10E+05 2871 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.evt
Total Good Bad: Region Time Phase Cut
2871 257 2614 0 0 0
Writing events file
257 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2871 257 2614 0 0 0
in 10476.52 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region ad71039000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71039000g300270h_2.ulc use_events=yes
Wrote events list to file ad71039000g300270h_2.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71039000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 998 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.evt
Total Good Bad: Region Time Phase Cut
998 95 903 0 0 0
Writing events file
95 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
998 95 903 0 0 0
in 9006.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad71039000s000102h_1.ulc use_events=yes
Wrote events list to file ad71039000s000102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71039000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.90E+04 1068 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000112h.evt
Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
Writing events file
101 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1068 101 967 0 0 0
in 9006.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad71039000s000112h_1.ulc use_events=yes
Wrote events list to file ad71039000s000112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad71039000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2021 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.evt
Total Good Bad: Region Time Phase Cut
2021 192 1829 0 0 0
Writing events file
192 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2021 192 1829 0 0 0
in 17616.68 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71039000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad71039000s000202m_1.ulc use_events=yes
Wrote events list to file ad71039000s000202m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71039000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.90E+04 1143 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.evt
Total Good Bad: Region Time Phase Cut
1143 130 1013 0 0 0
Writing events file
130 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1143 130 1013 0 0 0
in 8954.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad71039000s100102h_1.ulc use_events=yes
Wrote events list to file ad71039000s100102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71039000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.90E+04 1204 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100112h.evt
Total Good Bad: Region Time Phase Cut
1204 132 1072 0 0 0
Writing events file
132 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1204 132 1072 0 0 0
in 8954.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad71039000s100112h_1.ulc use_events=yes
Wrote events list to file ad71039000s100112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad71039000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.18E+05 2206 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.evt
Total Good Bad: Region Time Phase Cut
2206 234 1972 0 0 0
Writing events file
234 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2206 234 1972 0 0 0
in 17680.68 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad71039000s100202m_1.ulc use_events=yes
Wrote events list to file ad71039000s100202m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71039000s100402m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
in 37.24 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100402m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad71039000s100402m_1.ulc use_events=yes
Wrote events list to file ad71039000s100402m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71039000s100402m_1.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 MEDIUM 01/02/94 15:05:18 0.37E+02 50 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100412m.evt
Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50 1 49 0 0 0
in 37.24 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000s100412m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71039000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad71039000s100412m_1.ulc use_events=yes
Wrote events list to file ad71039000s100412m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/71039000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s100412m_1.ulc since it has 1 events*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 10887 Total of 0 sets of frame data are extracted.
1 ad71039000g200170m.unf 61021 1 ad71039000g200270h.unf 61021-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 46703 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 46703 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 14318 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.unf
Total Good Bad: Region Time Phase Cut
46703 13929 32774 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.unf
Total Good Bad: Region Time Phase Cut
14318 4565 9753 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
61021 18494 42527 0 0 0
in 56789.84 seconds
Spectrum has 18494 counts for 0.3257 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 56790. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > read events ad71039000g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad71039000g220170.cal group=yes
Wrote spectrum to ad71039000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 02:20:44 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad71039000g220170.cal
Net count rate (cts/s) for file 1 0.3257 +/- 2.3950E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.8769E+05 using 84 PHA bins.
Reduced chi-squared = 1.2827E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.7937E+05 using 84 PHA bins.
Reduced chi-squared = 1.2556E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.7937E+05 using 84 PHA bins.
Reduced chi-squared = 1.2397E+04
!XSPEC> renorm
Chi-Squared = 5779. using 84 PHA bins.
Reduced chi-squared = 73.15
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
4497.7 0 1.000 5.892 0.1005 0.1040
9.0346E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1465.3 0 1.000 5.860 0.1514 0.1600
7.9039E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
377.12 -1 1.000 5.901 0.1655 0.2249
5.3875E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
295.39 -2 1.000 5.930 0.1808 0.2464
4.0025E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
293.67 -3 1.000 5.925 0.1770 0.2446
4.1745E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
293.65 -4 1.000 5.926 0.1772 0.2449
4.1439E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
293.64 -5 1.000 5.926 0.1771 0.2449
4.1494E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
293.64 0 1.000 5.926 0.1771 0.2449
4.1492E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92578 +/- 0.38197E-02
3 3 2 gaussian/b Sigma 0.177054 +/- 0.42002E-02
4 4 2 gaussian/b norm 0.244866 +/- 0.26159E-02
5 2 3 gaussian/b LineE 6.52432 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.185781 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.149207E-02 +/- 0.17740E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 293.6 using 84 PHA bins.
Reduced chi-squared = 3.717
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad71039000g220170.cal peaks at 5.92578 +/- 0.0038197 keV1 ad71039000g300170m.unf 57517 1 ad71039000g300270h.unf 57517-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 43831 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 43831 1024
2 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 13686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.unf
Total Good Bad: Region Time Phase Cut
43831 12532 31299 0 0 0
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.unf
Total Good Bad: Region Time Phase Cut
13686 4130 9556 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57517 16662 40855 0 0 0
in 56785.84 seconds
Spectrum has 16662 counts for 0.2934 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 56786. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71039000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!xsel:ASCA > read events ad71039000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > read events ad71039000g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad71039000g320170.cal group=yes
Wrote spectrum to ad71039000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 02:21:39 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad71039000g320170.cal
Net count rate (cts/s) for file 1 0.2934 +/- 2.2736E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.0994E+06 using 84 PHA bins.
Reduced chi-squared = 1.4279E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.0900E+06 using 84 PHA bins.
Reduced chi-squared = 1.3974E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.0900E+06 using 84 PHA bins.
Reduced chi-squared = 1.3797E+04
!XSPEC> renorm
Chi-Squared = 5502. using 84 PHA bins.
Reduced chi-squared = 69.65
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
4338.9 0 1.000 5.893 9.2101E-02 9.5747E-02
8.2483E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1572.3 0 1.000 5.868 0.1367 0.1488
7.1038E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
322.14 -1 1.000 5.924 0.1466 0.2118
4.4935E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
219.38 -2 1.000 5.950 0.1560 0.2331
3.3410E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
216.75 -3 1.000 5.945 0.1512 0.2317
3.4904E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
216.70 -4 1.000 5.946 0.1512 0.2319
3.4709E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
216.69 -5 1.000 5.946 0.1511 0.2318
3.4736E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
216.69 -6 1.000 5.946 0.1511 0.2318
3.4734E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94590 +/- 0.33231E-02
3 3 2 gaussian/b Sigma 0.151071 +/- 0.41668E-02
4 4 2 gaussian/b norm 0.231847 +/- 0.23734E-02
5 2 3 gaussian/b LineE 6.54647 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.158517 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.473397E-02 +/- 0.14323E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 216.7 using 84 PHA bins.
Reduced chi-squared = 2.743
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad71039000g320170.cal peaks at 5.94590 +/- 0.0033231 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.14E+05 111829 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71039000s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.14E+05 112207 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.48E+05 258554 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s000202m.unf
Total Good Bad: Region Time Phase Cut
258554 15035 0 243519 0 0
Writing events file
15035 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
258554 15035 0 243519 0 0
in 1777.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71039000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71039000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 15035
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 56 10526
Flickering pixels iter, pixels & cnts : 1 25 306
cleaning chip # 1
Hot pixels & counts : 19 2998
Flickering pixels iter, pixels & cnts : 1 11 81
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 111
Number of (internal) image counts : 15035
Number of image cts rejected (N, %) : 13911 92.5241089
By chip : 0 1 2 3
Pixels rejected : 81 30 0 0
Image counts : 11370 3665 0 0
Image cts rejected: 10832 3079 0 0
Image cts rej (%) : 95.27 84.01 0.00 0.00
filtering data...
Total counts : 11370 3665 0 0
Total cts rejected: 10832 3079 0 0
Total cts rej (%) : 95.27 84.01 0.00 0.00
Number of clean counts accepted : 1124
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 111
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71039000s000302h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 23:39:08 0.82E+02 5120 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s000302h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71039000s000302h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 23:39:08 0.82E+02 5120 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s000312h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s000312h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT HIGH 01/02/94 03:15:54 0.14E+05 88590 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71039000s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 HIGH 01/02/94 03:15:54 0.14E+05 88856 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 03:17:02 0.48E+05 221467 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000s100202m.unf
Total Good Bad: Region Time Phase Cut
221467 11476 0 209991 0 0
Writing events file
11476 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
221467 11476 0 209991 0 0
in 1777.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71039000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71039000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 11476
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 29 4556
Flickering pixels iter, pixels & cnts : 1 4 36
cleaning chip # 3
Hot pixels & counts : 33 5668
Flickering pixels iter, pixels & cnts : 1 8 128
Number of pixels rejected : 74
Number of (internal) image counts : 11476
Number of image cts rejected (N, %) : 10388 90.5193481
By chip : 0 1 2 3
Pixels rejected : 0 0 33 41
Image counts : 0 0 5141 6335
Image cts rejected: 0 0 4592 5796
Image cts rej (%) : 0.00 0.00 89.32 91.49
filtering data...
Total counts : 0 0 5141 6335
Total cts rejected: 0 0 4592 5796
Total cts rej (%) : 0.00 0.00 89.32 91.49
Number of clean counts accepted : 1088
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 74
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71039000s100402m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT MEDIUM 01/02/94 15:05:18 0.40E+03 1070 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s100402m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s100402m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71039000s100402m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC4968 BRIGHT2 MEDIUM 01/02/94 15:05:18 0.40E+03 1074 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000s100412m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000s100412m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71039000s100412m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 46703 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.unf
Total Good Bad: Region Time Phase Cut
46703 1308 0 45395 0 0
Writing events file
1308 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
46703 1308 0 45395 0 0
in 1568.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad71039000g200170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 46703 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200170m.unf
Total Good Bad: Region Time Phase Cut
46703 20445 0 26258 0 0
Writing events file
20445 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
46703 20445 0 26258 0 0
in 16127.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71039000g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 14318 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71039000g200270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 14318 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g200270h.unf
Total Good Bad: Region Time Phase Cut
14318 3263 0 11055 0 0
Writing events file
3263 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14318 3263 0 11055 0 0
in 2319.80 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71039000g300170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 43831 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.unf
Total Good Bad: Region Time Phase Cut
43831 1174 0 42657 0 0
Writing events file
1174 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
43831 1174 0 42657 0 0
in 1568.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad71039000g300170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH MEDIUM 01/02/94 03:17:46 0.43E+05 43831 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300170m.unf
Total Good Bad: Region Time Phase Cut
43831 19743 0 24088 0 0
Writing events file
19743 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
43831 19743 0 24088 0 0
in 16127.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71039000g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 13686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71039000g300270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC4968 PH HIGH 01/02/94 03:16:02 0.14E+05 13686 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/71039000.004/ad71039000g300270h.unf
Total Good Bad: Region Time Phase Cut
13686 3335 0 10351 0 0
Writing events file
3335 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13686 3335 0 10351 0 0
in 2319.80 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/71039000.004/
Setting mkf directory to /data/data24/seq_proc/71039000.004/
!earthevents:ASCA > read events ad71039000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/71039000.004/
HK Directory is: /data/data24/seq_proc/71039000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad71039000s000102h.unf|S0CCDPOW|1100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000302h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000102h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000302h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000102h.unf|S0CCDLST|1 0 1 0|S0 CCD readout order ad71039000s000302h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order-> listing ad71039000s000102h.unf
ad71039000s000112h.unf|S0CCDPOW|1100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000312h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000112h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000312h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000112h.unf|S0CCDLST|1 0 1 0|S0 CCD readout order ad71039000s000312h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order-> listing ad71039000s000112h.unf
ad71039000s000101h.unf|S0CCDPOW|1100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000301h.unf|S0CCDPOW|0100|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad71039000s000101h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000301h.unf|S0CCDMOD|1|How many S0 CCDs are in use: 1, 2, or 4 ad71039000s000101h.unf|S0CCDLST|1 0 1 0|S0 CCD readout order ad71039000s000301h.unf|S0CCDLST|1 1 1 1|S0 CCD readout order-> listing ad71039000s000101h.unf
ad71039000s100202m.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad71039000s100402m.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad71039000s100202m.unf
ad71039000s100101h.unf|S1CCDPOW|0011|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad71039000s100301h.unf|S1CCDPOW|0001|Which S1 CCDs are in use(0123): 0=OFF 1=ON ad71039000s100101h.unf|S1CCDMOD|2|How many S1 CCDs are in use: 1, 2, or 4 ad71039000s100301h.unf|S1CCDMOD|1|How many S1 CCDs are in use: 1, 2, or 4 ad71039000s100101h.unf|S1CCDLST|3 2 3 2|S1 CCD readout order ad71039000s100301h.unf|S1CCDLST|3 3 3 3|S1 CCD readout order-> listing ad71039000s100101h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files