The following information is also available:
Time column is TIME ORDERED-> Fetching fa940504_0721.2000.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 42189705.054600 42235248.918300
Data file start and stop ascatime : 42189705.054600 42235248.918300
Aspecting run start and stop ascatime : 42189705.054706 42235248.918195
Time interval averaged over (seconds) : 45543.863489
Total pointing and manuver time (sec) : 27812.982422 17730.984375
Mean boresight Euler angles : 150.689464 61.229846 155.462537
RA DEC SUN ANGLE
Mean solar position (deg) : 40.44 15.71
Mean aberration (arcsec) : 5.91 3.86
Mean sat X-axis (deg) : 287.203116 52.882108 90.76
Mean sat Y-axis (deg) : 48.297354 21.347526 9.34
Mean sat Z-axis (deg) : 150.689464 28.770154 99.31
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 150.365738 28.753752 65.618454 0.181230
Minimum 150.257187 28.716465 64.789764 0.005336
Maximum 150.503372 28.986240 65.718658 107.307594
Sigma (RMS) 0.000373 0.000376 0.009098 0.928407
Number of ASPECT records processed = 17427
Aspecting to RA/DEC : 150.36573792 28.75375175
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 150.366 DEC: 28.754
START TIME: SC 42189705.0547 = UT 04/05/94 07:21:45
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000125 5.639 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
7.999902 5.571 D828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 3
207.999374 4.564 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
575.998413 3.554 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
643.998108 2.548 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
723.997925 1.548 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1755.994751 0.541 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
2215.993408 0.427 D820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 3
5751.982910 0.515 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
7975.976074 0.198 D820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 3
11511.965820 0.132 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
13719.958984 0.034 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
17255.949219 0.168 D828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 3
19479.941406 0.033 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
23005.931641 0.121 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
25223.925781 0.030 D820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 3
28759.914062 0.059 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
30983.908203 0.043 D820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 3
34519.898438 0.042 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
36727.890625 0.083 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
40279.878906 0.089 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
42487.875000 0.183 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
45527.863281 15.712 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
45543.863281 107.308 3E03 1 1 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0
Attitude Records: 17427
Attitude Steps: 24
Maneuver ACM time: 17731.0 sec
Pointed ACM time: 27813.0 sec
-> Calculating aspect point99 100 count=4 sum1=602.348 sum2=245.06 sum3=622.226 100 99 count=20 sum1=3011.93 sum2=1225.26 sum3=3110.81 100 100 count=1 sum1=150.591 sum2=61.265 sum3=155.536 101 99 count=36 sum1=5421.86 sum2=2205.37 sum3=5598.95 102 99 count=73 sum1=10994.9 sum2=4471.87 sum3=11352.7 103 99 count=12 sum1=1807.51 sum2=735.074 sum3=1866.11 104 98 count=7 sum1=1054.46 sum2=428.775 sum3=1088.51 104 99 count=1 sum1=150.633 sum2=61.255 sum3=155.504 105 98 count=8 sum1=1205.17 sum2=490.014 sum3=1243.97 106 98 count=11 sum1=1657.22 sum2=673.742 sum3=1710.38 107 98 count=12 sum1=1808 sum2=734.963 sum3=1865.79 108 97 count=15 sum1=2260.15 sum2=918.665 sum3=2332.14 108 98 count=1 sum1=150.672 sum2=61.246 sum3=155.479 109 96 count=14966 sum1=2.25522e+06 sum2=916356 sum3=2.32664e+06 109 97 count=37 sum1=5575.41 sum2=2265.93 sum3=5752.38 110 96 count=683 sum1=102923 sum2=41821.8 sum3=106182 110 97 count=1537 sum1=231617 sum2=94120.6 sum3=238954 123 73 count=1 sum1=150.828 sum2=60.997 sum3=155.446 1 out of 17426 points outside bin structure-> Euler angles: 150.69, 61.23, 155.462
Interpolating 1 records in time interval 4.21897e+07 - 4.21897e+07 Interpolating 26 records in time interval 4.22352e+07 - 4.22352e+07 Interpolating 154 records in time interval 4.22352e+07 - 4.22352e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft940504_0721.2000",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft940504_0721.2000 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 279168 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 279168 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 4368 no. of SIS events found = 446062-> Standard Error Output From FTOOL frfread
coordinate error 0 1-> Removing the following files with NEVENTS=0
ft940504_0721_2000G200270M.fits ft940504_0721_2000G200370M.fits ft940504_0721_2000G200670M.fits ft940504_0721_2000G200770M.fits ft940504_0721_2000G201199.fits ft940504_0721_2000G202870M.fits ft940504_0721_2000G202970L.fits ft940504_0721_2000G300270M.fits ft940504_0721_2000G300370M.fits ft940504_0721_2000G300670M.fits ft940504_0721_2000G300770M.fits ft940504_0721_2000G301199.fits ft940504_0721_2000G301470H.fits ft940504_0721_2000G302870M.fits ft940504_0721_2000G302970L.fits ft940504_0721_2000S001199.fits ft940504_0721_2000S001601M.fits ft940504_0721_2000S001901M.fits ft940504_0721_2000S002101M.fits ft940504_0721_2000S003101M.fits ft940504_0721_2000S101199.fits ft940504_0721_2000S101601M.fits ft940504_0721_2000S101901M.fits ft940504_0721_2000S102101M.fits ft940504_0721_2000S103101M.fits-> Checking for empty GTI extensions
ft940504_0721_2000S000101M.fits[3] ft940504_0721_2000S000201M.fits[3] ft940504_0721_2000S000301M.fits[3] ft940504_0721_2000S000401M.fits[3] ft940504_0721_2000S000501M.fits[3] ft940504_0721_2000S000601M.fits[3] ft940504_0721_2000S000701M.fits[3] ft940504_0721_2000S000801H.fits[3] ft940504_0721_2000S000901H.fits[3] ft940504_0721_2000S001001H.fits[3] ft940504_0721_2000S001201M.fits[3] ft940504_0721_2000S001301H.fits[3] ft940504_0721_2000S001401H.fits[3] ft940504_0721_2000S001501M.fits[3] ft940504_0721_2000S001701M.fits[3] ft940504_0721_2000S001801L.fits[3] ft940504_0721_2000S002001M.fits[3] ft940504_0721_2000S002201M.fits[3] ft940504_0721_2000S002301L.fits[3] ft940504_0721_2000S002401M.fits[3] ft940504_0721_2000S002501M.fits[3] ft940504_0721_2000S002601M.fits[3] ft940504_0721_2000S002701L.fits[3] ft940504_0721_2000S002801M.fits[3] ft940504_0721_2000S002901L.fits[3] ft940504_0721_2000S003001M.fits[3] ft940504_0721_2000S003201M.fits[3]-> Merging GTIs from the following files:
ft940504_0721_2000S100101M.fits[3] ft940504_0721_2000S100201M.fits[3] ft940504_0721_2000S100301M.fits[3] ft940504_0721_2000S100401M.fits[3] ft940504_0721_2000S100501M.fits[3] ft940504_0721_2000S100601M.fits[3] ft940504_0721_2000S100701M.fits[3] ft940504_0721_2000S100801H.fits[3] ft940504_0721_2000S100901H.fits[3] ft940504_0721_2000S101001H.fits[3] ft940504_0721_2000S101201M.fits[3] ft940504_0721_2000S101301H.fits[3] ft940504_0721_2000S101401H.fits[3] ft940504_0721_2000S101501M.fits[3] ft940504_0721_2000S101701M.fits[3] ft940504_0721_2000S101801L.fits[3] ft940504_0721_2000S102001M.fits[3] ft940504_0721_2000S102201M.fits[3] ft940504_0721_2000S102301L.fits[3] ft940504_0721_2000S102401M.fits[3] ft940504_0721_2000S102501M.fits[3] ft940504_0721_2000S102601M.fits[3] ft940504_0721_2000S102701L.fits[3] ft940504_0721_2000S102801M.fits[3] ft940504_0721_2000S102901L.fits[3] ft940504_0721_2000S103001M.fits[3] ft940504_0721_2000S103201M.fits[3]-> Merging GTIs from the following files:
ft940504_0721_2000G200170M.fits[3] ft940504_0721_2000G200470M.fits[3] ft940504_0721_2000G200570M.fits[3] ft940504_0721_2000G200870M.fits[3] ft940504_0721_2000G200970M.fits[3] ft940504_0721_2000G201070H.fits[3] ft940504_0721_2000G201270M.fits[3] ft940504_0721_2000G201370H.fits[3] ft940504_0721_2000G201470H.fits[3] ft940504_0721_2000G201570H.fits[3] ft940504_0721_2000G201670H.fits[3] ft940504_0721_2000G201770M.fits[3] ft940504_0721_2000G201870M.fits[3] ft940504_0721_2000G201970L.fits[3] ft940504_0721_2000G202070M.fits[3] ft940504_0721_2000G202170L.fits[3] ft940504_0721_2000G202270L.fits[3] ft940504_0721_2000G202370M.fits[3] ft940504_0721_2000G202470M.fits[3] ft940504_0721_2000G202570M.fits[3] ft940504_0721_2000G202670M.fits[3] ft940504_0721_2000G202770M.fits[3] ft940504_0721_2000G203070L.fits[3] ft940504_0721_2000G203170M.fits[3] ft940504_0721_2000G203270M.fits[3] ft940504_0721_2000G203370M.fits[3] ft940504_0721_2000G203470M.fits[3] ft940504_0721_2000G203570L.fits[3] ft940504_0721_2000G203670L.fits[3] ft940504_0721_2000G203770M.fits[3] ft940504_0721_2000G203870M.fits[3] ft940504_0721_2000G203970M.fits[3] ft940504_0721_2000G204070M.fits[3]-> Merging GTIs from the following files:
ft940504_0721_2000G300170M.fits[3] ft940504_0721_2000G300470M.fits[3] ft940504_0721_2000G300570M.fits[3] ft940504_0721_2000G300870M.fits[3] ft940504_0721_2000G300970M.fits[3] ft940504_0721_2000G301070H.fits[3] ft940504_0721_2000G301270M.fits[3] ft940504_0721_2000G301370H.fits[3] ft940504_0721_2000G301570H.fits[3] ft940504_0721_2000G301670H.fits[3] ft940504_0721_2000G301770M.fits[3] ft940504_0721_2000G301870M.fits[3] ft940504_0721_2000G301970L.fits[3] ft940504_0721_2000G302070M.fits[3] ft940504_0721_2000G302170L.fits[3] ft940504_0721_2000G302270L.fits[3] ft940504_0721_2000G302370M.fits[3] ft940504_0721_2000G302470M.fits[3] ft940504_0721_2000G302570M.fits[3] ft940504_0721_2000G302670M.fits[3] ft940504_0721_2000G302770M.fits[3] ft940504_0721_2000G303070L.fits[3] ft940504_0721_2000G303170M.fits[3] ft940504_0721_2000G303270M.fits[3] ft940504_0721_2000G303370M.fits[3] ft940504_0721_2000G303470M.fits[3] ft940504_0721_2000G303570L.fits[3] ft940504_0721_2000G303670L.fits[3] ft940504_0721_2000G303770M.fits[3] ft940504_0721_2000G303870M.fits[3] ft940504_0721_2000G303970M.fits[3] ft940504_0721_2000G304070M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 2 photon cnt = 2664 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 35 GISSORTSPLIT:LO:g200270l.prelist merge count = 3 photon cnt = 1989 GISSORTSPLIT:LO:g200370l.prelist merge count = 2 photon cnt = 160 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 13 GISSORTSPLIT:LO:g200370m.prelist merge count = 9 photon cnt = 24774 GISSORTSPLIT:LO:g200470m.prelist merge count = 4 photon cnt = 66 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 21 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200870m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g200970m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:g201070m.prelist merge count = 1 photon cnt = 19 GISSORTSPLIT:LO:Total filenames split = 33 GISSORTSPLIT:LO:Total split file cnt = 17 GISSORTSPLIT:LO:End program-> Creating ad71043000g200170m.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G200170M.fits 2 -- ft940504_0721_2000G200570M.fits 3 -- ft940504_0721_2000G200970M.fits 4 -- ft940504_0721_2000G201270M.fits 5 -- ft940504_0721_2000G201870M.fits 6 -- ft940504_0721_2000G202070M.fits 7 -- ft940504_0721_2000G202670M.fits 8 -- ft940504_0721_2000G203470M.fits 9 -- ft940504_0721_2000G204070M.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G200170M.fits 2 -- ft940504_0721_2000G200570M.fits 3 -- ft940504_0721_2000G200970M.fits 4 -- ft940504_0721_2000G201270M.fits 5 -- ft940504_0721_2000G201870M.fits 6 -- ft940504_0721_2000G202070M.fits 7 -- ft940504_0721_2000G202670M.fits 8 -- ft940504_0721_2000G203470M.fits 9 -- ft940504_0721_2000G204070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000g200270h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G201070H.fits 2 -- ft940504_0721_2000G201670H.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G201070H.fits 2 -- ft940504_0721_2000G201670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000g200370l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G201970L.fits 2 -- ft940504_0721_2000G202270L.fits 3 -- ft940504_0721_2000G203670L.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G201970L.fits 2 -- ft940504_0721_2000G202270L.fits 3 -- ft940504_0721_2000G203670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000160 events
ft940504_0721_2000G202170L.fits ft940504_0721_2000G203570L.fits-> Ignoring the following files containing 000000066 events
ft940504_0721_2000G201770M.fits ft940504_0721_2000G202570M.fits ft940504_0721_2000G203370M.fits ft940504_0721_2000G203970M.fits-> Ignoring the following files containing 000000035 events
ft940504_0721_2000G203070L.fits-> Ignoring the following files containing 000000021 events
ft940504_0721_2000G203770M.fits-> Ignoring the following files containing 000000019 events
ft940504_0721_2000G203270M.fits-> Ignoring the following files containing 000000019 events
ft940504_0721_2000G203170M.fits-> Ignoring the following files containing 000000016 events
ft940504_0721_2000G203870M.fits-> Ignoring the following files containing 000000013 events
ft940504_0721_2000G200470M.fits ft940504_0721_2000G200870M.fits-> Ignoring the following files containing 000000012 events
ft940504_0721_2000G202370M.fits-> Ignoring the following files containing 000000010 events
ft940504_0721_2000G202470M.fits-> Ignoring the following files containing 000000004 events
ft940504_0721_2000G201470H.fits-> Ignoring the following files containing 000000003 events
ft940504_0721_2000G201370H.fits-> Ignoring the following files containing 000000003 events
ft940504_0721_2000G202770M.fits-> Ignoring the following files containing 000000001 events
ft940504_0721_2000G201570H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 2 photon cnt = 2552 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 28 GISSORTSPLIT:LO:g300270l.prelist merge count = 3 photon cnt = 1812 GISSORTSPLIT:LO:g300370l.prelist merge count = 2 photon cnt = 162 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300270m.prelist merge count = 2 photon cnt = 10 GISSORTSPLIT:LO:g300370m.prelist merge count = 9 photon cnt = 23308 GISSORTSPLIT:LO:g300470m.prelist merge count = 4 photon cnt = 76 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 22 GISSORTSPLIT:LO:g300970m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g301070m.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:Total filenames split = 32 GISSORTSPLIT:LO:Total split file cnt = 16 GISSORTSPLIT:LO:End program-> Creating ad71043000g300170m.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G300170M.fits 2 -- ft940504_0721_2000G300570M.fits 3 -- ft940504_0721_2000G300970M.fits 4 -- ft940504_0721_2000G301270M.fits 5 -- ft940504_0721_2000G301870M.fits 6 -- ft940504_0721_2000G302070M.fits 7 -- ft940504_0721_2000G302670M.fits 8 -- ft940504_0721_2000G303470M.fits 9 -- ft940504_0721_2000G304070M.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G300170M.fits 2 -- ft940504_0721_2000G300570M.fits 3 -- ft940504_0721_2000G300970M.fits 4 -- ft940504_0721_2000G301270M.fits 5 -- ft940504_0721_2000G301870M.fits 6 -- ft940504_0721_2000G302070M.fits 7 -- ft940504_0721_2000G302670M.fits 8 -- ft940504_0721_2000G303470M.fits 9 -- ft940504_0721_2000G304070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000g300270h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G301070H.fits 2 -- ft940504_0721_2000G301670H.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G301070H.fits 2 -- ft940504_0721_2000G301670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000g300370l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000G301970L.fits 2 -- ft940504_0721_2000G302270L.fits 3 -- ft940504_0721_2000G303670L.fits Merging binary extension #: 2 1 -- ft940504_0721_2000G301970L.fits 2 -- ft940504_0721_2000G302270L.fits 3 -- ft940504_0721_2000G303670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000162 events
ft940504_0721_2000G302170L.fits ft940504_0721_2000G303570L.fits-> Ignoring the following files containing 000000076 events
ft940504_0721_2000G301770M.fits ft940504_0721_2000G302570M.fits ft940504_0721_2000G303370M.fits ft940504_0721_2000G303970M.fits-> Ignoring the following files containing 000000028 events
ft940504_0721_2000G303070L.fits-> Ignoring the following files containing 000000022 events
ft940504_0721_2000G303270M.fits-> Ignoring the following files containing 000000017 events
ft940504_0721_2000G302370M.fits-> Ignoring the following files containing 000000017 events
ft940504_0721_2000G303870M.fits-> Ignoring the following files containing 000000014 events
ft940504_0721_2000G302470M.fits-> Ignoring the following files containing 000000013 events
ft940504_0721_2000G303170M.fits-> Ignoring the following files containing 000000011 events
ft940504_0721_2000G303770M.fits-> Ignoring the following files containing 000000010 events
ft940504_0721_2000G300470M.fits ft940504_0721_2000G300870M.fits-> Ignoring the following files containing 000000003 events
ft940504_0721_2000G301370H.fits-> Ignoring the following files containing 000000003 events
ft940504_0721_2000G302770M.fits-> Ignoring the following files containing 000000002 events
ft940504_0721_2000G301570H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 24 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 3 photon cnt = 53473 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 49 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 4 photon cnt = 7323 SIS0SORTSPLIT:LO:s000501m.prelist merge count = 14 photon cnt = 124008 SIS0SORTSPLIT:LO:s000601m.prelist merge count = 4 photon cnt = 128 SIS0SORTSPLIT:LO:Total filenames split = 27 SIS0SORTSPLIT:LO:Total split file cnt = 6 SIS0SORTSPLIT:LO:End program-> Creating ad71043000s000101m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S000101M.fits 2 -- ft940504_0721_2000S000301M.fits 3 -- ft940504_0721_2000S000501M.fits 4 -- ft940504_0721_2000S000701M.fits 5 -- ft940504_0721_2000S001201M.fits 6 -- ft940504_0721_2000S001501M.fits 7 -- ft940504_0721_2000S001701M.fits 8 -- ft940504_0721_2000S002001M.fits 9 -- ft940504_0721_2000S002201M.fits 10 -- ft940504_0721_2000S002401M.fits 11 -- ft940504_0721_2000S002601M.fits 12 -- ft940504_0721_2000S002801M.fits 13 -- ft940504_0721_2000S003001M.fits 14 -- ft940504_0721_2000S003201M.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S000101M.fits 2 -- ft940504_0721_2000S000301M.fits 3 -- ft940504_0721_2000S000501M.fits 4 -- ft940504_0721_2000S000701M.fits 5 -- ft940504_0721_2000S001201M.fits 6 -- ft940504_0721_2000S001501M.fits 7 -- ft940504_0721_2000S001701M.fits 8 -- ft940504_0721_2000S002001M.fits 9 -- ft940504_0721_2000S002201M.fits 10 -- ft940504_0721_2000S002401M.fits 11 -- ft940504_0721_2000S002601M.fits 12 -- ft940504_0721_2000S002801M.fits 13 -- ft940504_0721_2000S003001M.fits 14 -- ft940504_0721_2000S003201M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000s000201h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S000801H.fits 2 -- ft940504_0721_2000S001001H.fits 3 -- ft940504_0721_2000S001401H.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S000801H.fits 2 -- ft940504_0721_2000S001001H.fits 3 -- ft940504_0721_2000S001401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000s000301l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S001801L.fits 2 -- ft940504_0721_2000S002301L.fits 3 -- ft940504_0721_2000S002701L.fits 4 -- ft940504_0721_2000S002901L.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S001801L.fits 2 -- ft940504_0721_2000S002301L.fits 3 -- ft940504_0721_2000S002701L.fits 4 -- ft940504_0721_2000S002901L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000128 events
ft940504_0721_2000S000201M.fits ft940504_0721_2000S000401M.fits ft940504_0721_2000S000601M.fits ft940504_0721_2000S002501M.fits-> Ignoring the following files containing 000000049 events
ft940504_0721_2000S000901H.fits-> Ignoring the following files containing 000000024 events
ft940504_0721_2000S001301H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 28 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 3 photon cnt = 63551 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 84 SIS1SORTSPLIT:LO:s100401l.prelist merge count = 4 photon cnt = 7392 SIS1SORTSPLIT:LO:s100501m.prelist merge count = 14 photon cnt = 189873 SIS1SORTSPLIT:LO:s100601m.prelist merge count = 4 photon cnt = 128 SIS1SORTSPLIT:LO:Total filenames split = 27 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad71043000s100101m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S100101M.fits 2 -- ft940504_0721_2000S100301M.fits 3 -- ft940504_0721_2000S100501M.fits 4 -- ft940504_0721_2000S100701M.fits 5 -- ft940504_0721_2000S101201M.fits 6 -- ft940504_0721_2000S101501M.fits 7 -- ft940504_0721_2000S101701M.fits 8 -- ft940504_0721_2000S102001M.fits 9 -- ft940504_0721_2000S102201M.fits 10 -- ft940504_0721_2000S102401M.fits 11 -- ft940504_0721_2000S102601M.fits 12 -- ft940504_0721_2000S102801M.fits 13 -- ft940504_0721_2000S103001M.fits 14 -- ft940504_0721_2000S103201M.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S100101M.fits 2 -- ft940504_0721_2000S100301M.fits 3 -- ft940504_0721_2000S100501M.fits 4 -- ft940504_0721_2000S100701M.fits 5 -- ft940504_0721_2000S101201M.fits 6 -- ft940504_0721_2000S101501M.fits 7 -- ft940504_0721_2000S101701M.fits 8 -- ft940504_0721_2000S102001M.fits 9 -- ft940504_0721_2000S102201M.fits 10 -- ft940504_0721_2000S102401M.fits 11 -- ft940504_0721_2000S102601M.fits 12 -- ft940504_0721_2000S102801M.fits 13 -- ft940504_0721_2000S103001M.fits 14 -- ft940504_0721_2000S103201M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000s100201h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S100801H.fits 2 -- ft940504_0721_2000S101001H.fits 3 -- ft940504_0721_2000S101401H.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S100801H.fits 2 -- ft940504_0721_2000S101001H.fits 3 -- ft940504_0721_2000S101401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad71043000s100301l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft940504_0721_2000S101801L.fits 2 -- ft940504_0721_2000S102301L.fits 3 -- ft940504_0721_2000S102701L.fits 4 -- ft940504_0721_2000S102901L.fits Merging binary extension #: 2 1 -- ft940504_0721_2000S101801L.fits 2 -- ft940504_0721_2000S102301L.fits 3 -- ft940504_0721_2000S102701L.fits 4 -- ft940504_0721_2000S102901L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000128 events
ft940504_0721_2000S100201M.fits ft940504_0721_2000S100401M.fits ft940504_0721_2000S100601M.fits ft940504_0721_2000S102501M.fits-> Ignoring the following files containing 000000084 events
ft940504_0721_2000S100901H.fits-> Ignoring the following files containing 000000028 events
ft940504_0721_2000S101301H.fits-> Tar-ing together the leftover raw files
a ft940504_0721_2000G200470M.fits 40K a ft940504_0721_2000G200870M.fits 40K a ft940504_0721_2000G201370H.fits 40K a ft940504_0721_2000G201470H.fits 40K a ft940504_0721_2000G201570H.fits 40K a ft940504_0721_2000G201770M.fits 40K a ft940504_0721_2000G202170L.fits 40K a ft940504_0721_2000G202370M.fits 40K a ft940504_0721_2000G202470M.fits 40K a ft940504_0721_2000G202570M.fits 40K a ft940504_0721_2000G202770M.fits 40K a ft940504_0721_2000G203070L.fits 40K a ft940504_0721_2000G203170M.fits 40K a ft940504_0721_2000G203270M.fits 40K a ft940504_0721_2000G203370M.fits 40K a ft940504_0721_2000G203570L.fits 40K a ft940504_0721_2000G203770M.fits 40K a ft940504_0721_2000G203870M.fits 40K a ft940504_0721_2000G203970M.fits 40K a ft940504_0721_2000G300470M.fits 40K a ft940504_0721_2000G300870M.fits 40K a ft940504_0721_2000G301370H.fits 40K a ft940504_0721_2000G301570H.fits 40K a ft940504_0721_2000G301770M.fits 40K a ft940504_0721_2000G302170L.fits 40K a ft940504_0721_2000G302370M.fits 40K a ft940504_0721_2000G302470M.fits 40K a ft940504_0721_2000G302570M.fits 40K a ft940504_0721_2000G302770M.fits 40K a ft940504_0721_2000G303070L.fits 40K a ft940504_0721_2000G303170M.fits 40K a ft940504_0721_2000G303270M.fits 40K a ft940504_0721_2000G303370M.fits 40K a ft940504_0721_2000G303570L.fits 40K a ft940504_0721_2000G303770M.fits 40K a ft940504_0721_2000G303870M.fits 40K a ft940504_0721_2000G303970M.fits 40K a ft940504_0721_2000S000201M.fits 40K a ft940504_0721_2000S000401M.fits 40K a ft940504_0721_2000S000601M.fits 40K a ft940504_0721_2000S000901H.fits 40K a ft940504_0721_2000S001301H.fits 40K a ft940504_0721_2000S002501M.fits 40K a ft940504_0721_2000S100201M.fits 40K a ft940504_0721_2000S100401M.fits 40K a ft940504_0721_2000S100601M.fits 40K a ft940504_0721_2000S100901H.fits 43K a ft940504_0721_2000S101301H.fits 40K a ft940504_0721_2000S102501M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft940504_0721.2000 'ft940504_0721.2000' is successfully opened Data Start Time is 42189696.05 (940504 072136) Time Margin 2.0 sec included 'ft940504_0721.2000' EOF detected, sf=4368 Data End Time is 42235235.92 (940504 200035) Gain History is written in ft940504_0721_2000.ghf-> Checking if column CAL_START in ft940504_0721_2000.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft940504_0721_2000.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad71043000g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000101m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000102m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000112m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000301l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s000312l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100101m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100102m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100112m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100301l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad71043000s100312l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 94/ 5/ 4 7:21 mjd=49476.306250 Orbit file name is ./frf.orbit.208 Epoch of Orbital Elements: 1994/4/30 8:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa940504_0721.2000 S0-HK file: ft940504_0721_2000S0HK.fits S1-HK file: ft940504_0721_2000S1HK.fits G2-HK file: ft940504_0721_2000G2HK.fits G3-HK file: ft940504_0721_2000G3HK.fits output FITS File: ft940504_0721_2000.mkf Total 1424 Data bins were processed.-> Checking if column TIME in ft940504_0721_2000.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 9967.4047 The mean of the selected column is 24.251593 The standard deviation of the selected column is 35.370517 The minimum of selected column is 7.0625210 The maximum of selected column is 711.00214 The number of points used in calculation is 411-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<130.3 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.32E+05 44002 0100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
41994 18925 0 23069 0 0
Writing events file
18925 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
41994 18925 0 23069 0 0
in 13517.78 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 18925
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 10 17827
Flickering pixels iter, pixels & cnts : 1 10 206
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 18925
Number of image cts rejected (N, %) : 18033 95.2866592
By chip : 0 1 2 3
Pixels rejected : 0 20 0 0
Image counts : 30 18895 0 0
Image cts rejected: 0 18033 0 0
Image cts rej (%) : 0.00 95.44 0.00 0.00
filtering data...
Total counts : 30 18895 0 0
Total cts rejected: 0 18033 0 0
Total cts rej (%) : 0.00 95.44 0.00 0.00
Number of clean counts accepted : 892
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000102m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71043000s000102m.evt use_events=no
Wrote cleaned events file to ad71043000s000102m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad71043000s000112m.unf into ad71043000s000112m.evtThe sum of the selected column is 9967.4047 The mean of the selected column is 24.251593 The standard deviation of the selected column is 35.370517 The minimum of selected column is 7.0625210 The maximum of selected column is 711.00214 The number of points used in calculation is 411-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<130.3 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.32E+05 44499 0100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000112m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
42189 19005 0 23184 0 0
Writing events file
19005 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
42189 19005 0 23184 0 0
in 13517.78 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 19005
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
Hot pixels & counts : 10 17827
Flickering pixels iter, pixels & cnts : 1 10 206
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 19005
Number of image cts rejected (N, %) : 18033 94.8855591
By chip : 0 1 2 3
Pixels rejected : 0 20 0 0
Image counts : 30 18975 0 0
Image cts rejected: 0 18033 0 0
Image cts rej (%) : 0.00 95.04 0.00 0.00
filtering data...
Total counts : 30 18975 0 0
Total cts rejected: 0 18033 0 0
Total cts rej (%) : 0.00 95.04 0.00 0.00
Number of clean counts accepted : 972
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000112m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad71043000s000112m.evt use_events=no
Wrote cleaned events file to ad71043000s000112m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad71043000s000201h.unf because of modeThe sum of the selected column is 2563.2785 The mean of the selected column is 28.167895 The standard deviation of the selected column is 10.244403 The minimum of selected column is 12.875038 The maximum of selected column is 69.343956 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1941.8600 The mean of the selected column is 21.339120 The standard deviation of the selected column is 7.3696660 The minimum of selected column is 9.5625286 The maximum of selected column is 47.906391 The number of points used in calculation is 91-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<58.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<43.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.33E+04 46007 1100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
44346 38104 0 6242 0 0
Writing events file
38104 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44346 38104 0 6242 0 0
in 2852.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 38104
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 86 26035
Flickering pixels iter, pixels & cnts : 1 30 760
cleaning chip # 1
Hot pixels & counts : 35 10786
Flickering pixels iter, pixels & cnts : 1 15 193
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 166
Number of (internal) image counts : 38104
Number of image cts rejected (N, %) : 37774 99.1339493
By chip : 0 1 2 3
Pixels rejected : 116 50 0 0
Image counts : 26944 11160 0 0
Image cts rejected: 26795 10979 0 0
Image cts rej (%) : 99.45 98.38 0.00 0.00
filtering data...
Total counts : 26944 11160 0 0
Total cts rejected: 26795 10979 0 0
Total cts rej (%) : 99.45 98.38 0.00 0.00
Number of clean counts accepted : 330
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 166
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71043000s000202h.evt use_events=no
Wrote cleaned events file to ad71043000s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad71043000s000212h.unf into ad71043000s000212h.evtThe sum of the selected column is 2563.2785 The mean of the selected column is 28.167895 The standard deviation of the selected column is 10.244403 The minimum of selected column is 12.875038 The maximum of selected column is 69.343956 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1941.8600 The mean of the selected column is 21.339120 The standard deviation of the selected column is 7.3696660 The minimum of selected column is 9.5625286 The maximum of selected column is 47.906391 The number of points used in calculation is 91-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<58.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<43.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:29 0.33E+04 46138 1100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
44427 38173 0 6254 0 0
Writing events file
38173 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44427 38173 0 6254 0 0
in 2852.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 38173
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 86 26076
Flickering pixels iter, pixels & cnts : 1 30 760
cleaning chip # 1
Hot pixels & counts : 35 10793
Flickering pixels iter, pixels & cnts : 1 15 194
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 166
Number of (internal) image counts : 38173
Number of image cts rejected (N, %) : 37823 99.0831223
By chip : 0 1 2 3
Pixels rejected : 116 50 0 0
Image counts : 26993 11180 0 0
Image cts rejected: 26836 10987 0 0
Image cts rej (%) : 99.42 98.27 0.00 0.00
filtering data...
Total counts : 26993 11180 0 0
Total cts rejected: 26836 10987 0 0
Total cts rej (%) : 99.42 98.27 0.00 0.00
Number of clean counts accepted : 350
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 166
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad71043000s000212h.evt use_events=no
Wrote cleaned events file to ad71043000s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad71043000s000301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.37E+04 1025 0100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
963 112 0 851 0 0
Writing events file
112 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
963 112 0 851 0 0
in 128.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 112
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 102
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 7
Number of (internal) image counts : 112
Number of image cts rejected (N, %) : 105 93.7500000
By chip : 0 1 2 3
Pixels rejected : 0 7 0 0
Image counts : 0 112 0 0
Image cts rejected: 0 105 0 0
Image cts rej (%) : 0.00 93.75 0.00 0.00
filtering data...
Total counts : 0 112 0 0
Total cts rejected: 0 105 0 0
Total cts rej (%) : 0.00 93.75 0.00 0.00
Number of clean counts accepted : 7
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad71043000s000302l.evt use_events=no
Wrote cleaned events file to ad71043000s000302l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad71043000s000312l.unf into ad71043000s000312l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.37E+04 1036 0100
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s000312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
968 112 0 856 0 0
Writing events file
112 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
968 112 0 856 0 0
in 128.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 112
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 6 102
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 7
Number of (internal) image counts : 112
Number of image cts rejected (N, %) : 105 93.7500000
By chip : 0 1 2 3
Pixels rejected : 0 7 0 0
Image counts : 0 112 0 0
Image cts rejected: 0 105 0 0
Image cts rej (%) : 0.00 93.75 0.00 0.00
filtering data...
Total counts : 0 112 0 0
Total cts rejected: 0 105 0 0
Total cts rej (%) : 0.00 93.75 0.00 0.00
Number of clean counts accepted : 7
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 7
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s000312l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad71043000s000312l.evt use_events=no
Wrote cleaned events file to ad71043000s000312l.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad71043000s100101m.unf because of modeThe sum of the selected column is 16212.698 The mean of the selected column is 39.446954 The standard deviation of the selected column is 16.329897 The minimum of selected column is 9.7187786 The maximum of selected column is 120.81286 The number of points used in calculation is 411-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<88.4 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.32E+05 117309 0001
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
114593 50948 0 63645 0 0
Writing events file
50948 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
114593 50948 0 63645 0 0
in 13389.75 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 50948
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 21 49903
Flickering pixels iter, pixels & cnts : 1 11 251
Number of pixels rejected : 32
Number of (internal) image counts : 50948
Number of image cts rejected (N, %) : 50154 98.4415512
By chip : 0 1 2 3
Pixels rejected : 0 0 0 32
Image counts : 0 0 0 50948
Image cts rejected: 0 0 0 50154
Image cts rej (%) : 0.00 0.00 0.00 98.44
filtering data...
Total counts : 0 0 0 50948
Total cts rejected: 0 0 0 50154
Total cts rej (%) : 0.00 0.00 0.00 98.44
Number of clean counts accepted : 794
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100102m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71043000s100102m.evt use_events=no
Wrote cleaned events file to ad71043000s100102m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad71043000s100112m.unf into ad71043000s100112m.evtThe sum of the selected column is 16212.698 The mean of the selected column is 39.446954 The standard deviation of the selected column is 16.329897 The minimum of selected column is 9.7187786 The maximum of selected column is 120.81286 The number of points used in calculation is 411-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<88.4 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.32E+05 117637 0001
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100112m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
114754 51005 0 63749 0 0
Writing events file
51005 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
114754 51005 0 63749 0 0
in 13389.75 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 51005
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 21 49903
Flickering pixels iter, pixels & cnts : 1 11 251
Number of pixels rejected : 32
Number of (internal) image counts : 51005
Number of image cts rejected (N, %) : 50154 98.3315353
By chip : 0 1 2 3
Pixels rejected : 0 0 0 32
Image counts : 0 0 0 51005
Image cts rejected: 0 0 0 50154
Image cts rej (%) : 0.00 0.00 0.00 98.33
filtering data...
Total counts : 0 0 0 51005
Total cts rejected: 0 0 0 50154
Total cts rej (%) : 0.00 0.00 0.00 98.33
Number of clean counts accepted : 851
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 32
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100112m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad71043000s100112m.evt use_events=no
Wrote cleaned events file to ad71043000s100112m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad71043000s100201h.unf because of modeThe sum of the selected column is 3172.6282 The mean of the selected column is 34.864046 The standard deviation of the selected column is 13.449789 The minimum of selected column is 15.375046 The maximum of selected column is 88.219009 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3669.3339 The mean of the selected column is 40.322350 The standard deviation of the selected column is 17.019257 The minimum of selected column is 16.031298 The maximum of selected column is 120.46911 The number of points used in calculation is 91-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<75.2 )&& (S1_PIXL3>0.0 && S1_PIXL3<91.3 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:25 0.33E+04 53287 0011
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
49613 42691 0 6922 0 0
Writing events file
42691 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
49613 42691 0 6922 0 0
in 2858.04 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 42691
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 67 20323
Flickering pixels iter, pixels & cnts : 1 33 486
cleaning chip # 3
Hot pixels & counts : 76 20410
Flickering pixels iter, pixels & cnts : 1 62 1112
Number of pixels rejected : 238
Number of (internal) image counts : 42691
Number of image cts rejected (N, %) : 42331 99.1567307
By chip : 0 1 2 3
Pixels rejected : 0 0 100 138
Image counts : 0 0 20974 21717
Image cts rejected: 0 0 20809 21522
Image cts rej (%) : 0.00 0.00 99.21 99.10
filtering data...
Total counts : 0 0 20974 21717
Total cts rejected: 0 0 20809 21522
Total cts rej (%) : 0.00 0.00 99.21 99.10
Number of clean counts accepted : 360
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 238
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71043000s100202h.evt use_events=no
Wrote cleaned events file to ad71043000s100202h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad71043000s100212h.unf into ad71043000s100212h.evtThe sum of the selected column is 3172.6282 The mean of the selected column is 34.864046 The standard deviation of the selected column is 13.449789 The minimum of selected column is 15.375046 The maximum of selected column is 88.219009 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3669.3339 The mean of the selected column is 40.322350 The standard deviation of the selected column is 17.019257 The minimum of selected column is 16.031298 The maximum of selected column is 120.46911 The number of points used in calculation is 91-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<75.2 )&& (S1_PIXL3>0.0 && S1_PIXL3<91.3 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:25 0.33E+04 53347 0011
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
49738 42796 0 6942 0 0
Writing events file
42796 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
49738 42796 0 6942 0 0
in 2858.04 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 42796
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 67 20353
Flickering pixels iter, pixels & cnts : 1 33 486
cleaning chip # 3
Hot pixels & counts : 76 20463
Flickering pixels iter, pixels & cnts : 1 62 1113
Number of pixels rejected : 238
Number of (internal) image counts : 42796
Number of image cts rejected (N, %) : 42415 99.1097336
By chip : 0 1 2 3
Pixels rejected : 0 0 100 138
Image counts : 0 0 21014 21782
Image cts rejected: 0 0 20839 21576
Image cts rej (%) : 0.00 0.00 99.17 99.05
filtering data...
Total counts : 0 0 21014 21782
Total cts rejected: 0 0 20839 21576
Total cts rej (%) : 0.00 0.00 99.17 99.05
Number of clean counts accepted : 381
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 238
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad71043000s100212h.evt use_events=no
Wrote cleaned events file to ad71043000s100212h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad71043000s100301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.37E+04 2918 0001
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad71043000s100302l.evt use_events=no
Wrote cleaned events file to ad71043000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71043000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.37E+04 2923 0001
Processing file: /data/data15/seq_proc/71043000.005/ad71043000s100312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data15/seq_proc/71043000.005/screen_in_event.xsl
reading data file: /data/data15/seq_proc/71043000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad71043000s100312l.evt use_events=no
Wrote cleaned events file to ad71043000s100312l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71043000s100312l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.unf
Total Good Bad: Region Time Phase Cut
24774 4025 17129 3620 0 0
Writing events file
4025 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24774 4025 17129 3620 0 0
in 14927.82 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4025 3472 553
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad71043000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 3472 in ad71043000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2664 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.unf
Total Good Bad: Region Time Phase Cut
2664 825 1796 43 0 0
Writing events file
825 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2664 825 1796 43 0 0
in 3130.06 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
825 728 97
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad71043000g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 728 in ad71043000g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1989 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g200370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad71043000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71043000g200370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.unf
Total Good Bad: Region Time Phase Cut
23308 4269 15163 3876 0 0
Writing events file
4269 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23308 4269 15163 3876 0 0
in 14927.82 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4269 3627 642
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad71043000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 3627 in ad71043000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2552 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.unf
Total Good Bad: Region Time Phase Cut
2552 884 1611 57 0 0
Writing events file
884 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2552 884 1611 57 0 0
in 3130.06 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
884 756 128
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad71043000g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 756 in ad71043000g300270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g300370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!screen:ASCA > read events ad71043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad71043000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71043000g300370l.evt since it contains 0 events-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad71043000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6271
Mean RA/DEC/ROLL : 150.3870 28.7734 65.6271
Pnt RA/DEC/ROLL : 150.2498 28.7016 65.6271
Image rebin factor : 1
Attitude Records : 17609
GTI intervals : 14
Total GTI (secs) : 14927.823
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1934.9833984 1934.9833984
20 Percent Complete: Total/live time: 3630.9702148 3630.9702148
30 Percent Complete: Total/live time: 5294.9653320 5294.9653320
40 Percent Complete: Total/live time: 6336.0004883 6336.0004883
50 Percent Complete: Total/live time: 8526.9492188 8526.9492188
60 Percent Complete: Total/live time: 9120.0019531 9120.0019531
70 Percent Complete: Total/live time: 12022.8417969 12022.8417969
80 Percent Complete: Total/live time: 12591.9453125 12591.9453125
90 Percent Complete: Total/live time: 13999.8251953 13999.8251953
100 Percent Complete: Total/live time: 14927.8271484 14927.8271484
Number of attitude steps used: 54
Number of attitude steps avail: 7980
Mean RA/DEC pixel offset: -1.2100 -2.9108
writing expo file: ad71043000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 3436 36 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3472 3436 36 0 0 0
in 14927.82 seconds
Image has 3436 counts for 0.2302 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 1485 36 0 0 1951
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3472 1485 36 0 0 1951
in 14927.82 seconds
Image has 1485 counts for 9.9479E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 1961 36 0 0 1475
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3472 1961 36 0 0 1475
in 14927.82 seconds
Image has 1961 counts for 0.1314 counts/sec
Command not found; type ? for a command listing
!ad71043000g200170m:ASCA >
!ad71043000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000g200170m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000g200170m:ASCA > read events ad71043000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000g200170m:ASCA-GIS2-PH > set image sky
!ad71043000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad71043000g200170m:ASCA-GIS2-PH > extract image
!ad71043000g200170m:ASCA-GIS2-PH > save image outfile=ad71043000g200170m.img
Wrote image to file ad71043000g200170m.img
!ad71043000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad71043000g200170m:ASCA-GIS2-PH > extract image
!ad71043000g200170m:ASCA-GIS2-PH > save image outfile=ad71043000g200170m_lo.img
Wrote image to file ad71043000g200170m_lo.img
!ad71043000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad71043000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71043000g200170m:ASCA-GIS2-PH > extract image
!ad71043000g200170m:ASCA-GIS2-PH > save image outfile=ad71043000g200170m_hi.img
Wrote image to file ad71043000g200170m_hi.img
!ad71043000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad71043000g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad71043000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6245
Mean RA/DEC/ROLL : 150.3864 28.7700 65.6245
Pnt RA/DEC/ROLL : 150.3466 28.7385 65.6245
Image rebin factor : 1
Attitude Records : 17609
GTI intervals : 4
Total GTI (secs) : 3130.061
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1579.9952393 1579.9952393
20 Percent Complete: Total/live time: 1579.9952393 1579.9952393
30 Percent Complete: Total/live time: 1589.4952393 1589.4952393
40 Percent Complete: Total/live time: 1589.4952393 1589.4952393
50 Percent Complete: Total/live time: 1614.9951172 1614.9951172
60 Percent Complete: Total/live time: 2062.0639648 2062.0639648
70 Percent Complete: Total/live time: 3130.0607910 3130.0607910
100 Percent Complete: Total/live time: 3130.0607910 3130.0607910
Number of attitude steps used: 11
Number of attitude steps avail: 6281
Mean RA/DEC pixel offset: -9.8205 -4.1803
writing expo file: ad71043000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 728 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 715 13 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
728 715 13 0 0 0
in 3130.06 seconds
Image has 715 counts for 0.2284 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 317 13 0 0 398
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
728 317 13 0 0 398
in 3130.06 seconds
Image has 317 counts for 0.1013 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 404 13 0 0 311
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
728 404 13 0 0 311
in 3130.06 seconds
Image has 404 counts for 0.1291 counts/sec
Command not found; type ? for a command listing
!ad71043000g200270h:ASCA >
!ad71043000g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000g200270h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000g200270h:ASCA > read events ad71043000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000g200270h:ASCA-GIS2-PH > set image sky
!ad71043000g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad71043000g200270h:ASCA-GIS2-PH > extract image
!ad71043000g200270h:ASCA-GIS2-PH > save image outfile=ad71043000g200270h.img
Wrote image to file ad71043000g200270h.img
!ad71043000g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad71043000g200270h:ASCA-GIS2-PH > extract image
!ad71043000g200270h:ASCA-GIS2-PH > save image outfile=ad71043000g200270h_lo.img
Wrote image to file ad71043000g200270h_lo.img
!ad71043000g200270h:ASCA-GIS2-PH > clear pha_cut
!ad71043000g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71043000g200270h:ASCA-GIS2-PH > extract image
!ad71043000g200270h:ASCA-GIS2-PH > save image outfile=ad71043000g200270h_hi.img
Wrote image to file ad71043000g200270h_hi.img
!ad71043000g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad71043000g300170m.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad71043000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6203
Mean RA/DEC/ROLL : 150.3728 28.7519 65.6203
Pnt RA/DEC/ROLL : 150.2640 28.7231 65.6203
Image rebin factor : 1
Attitude Records : 17609
GTI intervals : 14
Total GTI (secs) : 14927.823
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1934.9833984 1934.9833984
20 Percent Complete: Total/live time: 3630.9702148 3630.9702148
30 Percent Complete: Total/live time: 5294.9653320 5294.9653320
40 Percent Complete: Total/live time: 6336.0004883 6336.0004883
50 Percent Complete: Total/live time: 8526.9492188 8526.9492188
60 Percent Complete: Total/live time: 9120.0019531 9120.0019531
70 Percent Complete: Total/live time: 12022.8417969 12022.8417969
80 Percent Complete: Total/live time: 12591.9453125 12591.9453125
90 Percent Complete: Total/live time: 13999.8251953 13999.8251953
100 Percent Complete: Total/live time: 14927.8271484 14927.8271484
Number of attitude steps used: 54
Number of attitude steps avail: 7980
Mean RA/DEC pixel offset: 10.8687 -1.7109
writing expo file: ad71043000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 3587 40 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3627 3587 40 0 0 0
in 14927.82 seconds
Image has 3587 counts for 0.2403 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 1514 40 0 0 2073
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3627 1514 40 0 0 2073
in 14927.82 seconds
Image has 1514 counts for 0.1014 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 2077 40 0 0 1510
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3627 2077 40 0 0 1510
in 14927.82 seconds
Image has 2077 counts for 0.1391 counts/sec
Command not found; type ? for a command listing
!ad71043000g300170m:ASCA >
!ad71043000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000g300170m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000g300170m:ASCA > read events ad71043000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000g300170m:ASCA-GIS3-PH > set image sky
!ad71043000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad71043000g300170m:ASCA-GIS3-PH > extract image
!ad71043000g300170m:ASCA-GIS3-PH > save image outfile=ad71043000g300170m.img
Wrote image to file ad71043000g300170m.img
!ad71043000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad71043000g300170m:ASCA-GIS3-PH > extract image
!ad71043000g300170m:ASCA-GIS3-PH > save image outfile=ad71043000g300170m_lo.img
Wrote image to file ad71043000g300170m_lo.img
!ad71043000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad71043000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71043000g300170m:ASCA-GIS3-PH > extract image
!ad71043000g300170m:ASCA-GIS3-PH > save image outfile=ad71043000g300170m_hi.img
Wrote image to file ad71043000g300170m_hi.img
!ad71043000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad71043000g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad71043000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6178
Mean RA/DEC/ROLL : 150.3722 28.7485 65.6178
Pnt RA/DEC/ROLL : 150.3608 28.7600 65.6178
Image rebin factor : 1
Attitude Records : 17609
GTI intervals : 4
Total GTI (secs) : 3130.061
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1579.9952393 1579.9952393
20 Percent Complete: Total/live time: 1579.9952393 1579.9952393
30 Percent Complete: Total/live time: 1589.4952393 1589.4952393
40 Percent Complete: Total/live time: 1589.4952393 1589.4952393
50 Percent Complete: Total/live time: 1614.9951172 1614.9951172
60 Percent Complete: Total/live time: 2062.0639648 2062.0639648
70 Percent Complete: Total/live time: 3130.0607910 3130.0607910
100 Percent Complete: Total/live time: 3130.0607910 3130.0607910
Number of attitude steps used: 11
Number of attitude steps avail: 6281
Mean RA/DEC pixel offset: 1.1601 -3.0895
writing expo file: ad71043000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 756 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 742 14 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
756 742 14 0 0 0
in 3130.06 seconds
Image has 742 counts for 0.2371 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 325 14 0 0 417
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
756 325 14 0 0 417
in 3130.06 seconds
Image has 325 counts for 0.1038 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 419 14 0 0 323
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
756 419 14 0 0 323
in 3130.06 seconds
Image has 419 counts for 0.1339 counts/sec
Command not found; type ? for a command listing
!ad71043000g300270h:ASCA >
!ad71043000g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000g300270h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000g300270h:ASCA > read events ad71043000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000g300270h:ASCA-GIS3-PH > set image sky
!ad71043000g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad71043000g300270h:ASCA-GIS3-PH > extract image
!ad71043000g300270h:ASCA-GIS3-PH > save image outfile=ad71043000g300270h.img
Wrote image to file ad71043000g300270h.img
!ad71043000g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad71043000g300270h:ASCA-GIS3-PH > extract image
!ad71043000g300270h:ASCA-GIS3-PH > save image outfile=ad71043000g300270h_lo.img
Wrote image to file ad71043000g300270h_lo.img
!ad71043000g300270h:ASCA-GIS3-PH > clear pha_cut
!ad71043000g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad71043000g300270h:ASCA-GIS3-PH > extract image
!ad71043000g300270h:ASCA-GIS3-PH > save image outfile=ad71043000g300270h_hi.img
Wrote image to file ad71043000g300270h_hi.img
!ad71043000g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad71043000s000102m.expo
ASCAEXPO_V0.9b
reading data file: ad71043000s000102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6314
Mean RA/DEC/ROLL : 150.3953 28.7562 65.6314
Pnt RA/DEC/ROLL : 150.2350 28.7177 65.6314
Image rebin factor : 4
Attitude Records : 17609
Hot Pixels : 20
GTI intervals : 13
Total GTI (secs) : 13517.782
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1774.9833984 1774.9833984
20 Percent Complete: Total/live time: 3296.0000000 3296.0000000
30 Percent Complete: Total/live time: 5678.9638672 5678.9638672
40 Percent Complete: Total/live time: 5678.9638672 5678.9638672
50 Percent Complete: Total/live time: 8334.9482422 8334.9482422
60 Percent Complete: Total/live time: 8334.9482422 8334.9482422
70 Percent Complete: Total/live time: 9613.7841797 9613.7841797
80 Percent Complete: Total/live time: 11725.7832031 11725.7832031
90 Percent Complete: Total/live time: 13005.7832031 13005.7832031
100 Percent Complete: Total/live time: 13517.7851562 13517.7851562
Number of attitude steps used: 51
Number of attitude steps avail: 4110
Mean RA/DEC pixel offset: 48.5281 -86.8200
writing expo file: ad71043000s000102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000s000102m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000s000102m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 892 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
892 892 0 0 0 0
in 13517.78 seconds
Image has 892 counts for 6.5987E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 369 0 0 0 523
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
892 369 0 0 0 523
in 13517.78 seconds
Image has 369 counts for 2.7297E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 523 0 0 0 369
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
892 523 0 0 0 369
in 13517.78 seconds
Image has 523 counts for 3.8690E-02 counts/sec
Command not found; type ? for a command listing
!ad71043000s000102m:ASCA >
!ad71043000s000102m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000s000102m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000s000102m:ASCA > read events ad71043000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000s000102m:ASCA-SIS0-BRIGHT > set image sky
!ad71043000s000102m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad71043000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000102m.img
Wrote image to file ad71043000s000102m.img
!ad71043000s000102m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad71043000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000102m_lo.img
Wrote image to file ad71043000s000102m_lo.img
!ad71043000s000102m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad71043000s000102m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71043000s000102m:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000102m:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000102m_hi.img
Wrote image to file ad71043000s000102m_hi.img
!ad71043000s000102m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad71043000s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad71043000s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6288
Mean RA/DEC/ROLL : 150.3952 28.7529 65.6288
Pnt RA/DEC/ROLL : 150.3380 28.7556 65.6288
Image rebin factor : 4
Attitude Records : 17609
Hot Pixels : 166
GTI intervals : 8
Total GTI (secs) : 2852.004
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1521.9952393 1521.9952393
20 Percent Complete: Total/live time: 1521.9952393 1521.9952393
30 Percent Complete: Total/live time: 1531.4952393 1531.4952393
40 Percent Complete: Total/live time: 1531.4952393 1531.4952393
50 Percent Complete: Total/live time: 1556.9951172 1556.9951172
60 Percent Complete: Total/live time: 1862.9212646 1862.9212646
70 Percent Complete: Total/live time: 2852.0041504 2852.0041504
100 Percent Complete: Total/live time: 2852.0041504 2852.0041504
Number of attitude steps used: 11
Number of attitude steps avail: 6186
Mean RA/DEC pixel offset: -39.7783 -96.7357
writing expo file: ad71043000s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.29E+04 330 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.evt
Total Good Bad: Region Time Phase Cut
330 330 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
330 330 0 0 0 0
in 2852.00 seconds
Image has 330 counts for 0.1157 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.evt
Total Good Bad: Region Time Phase Cut
330 161 0 0 0 169
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
330 161 0 0 0 169
in 2852.00 seconds
Image has 161 counts for 5.6452E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.evt
Total Good Bad: Region Time Phase Cut
330 169 0 0 0 161
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
330 169 0 0 0 161
in 2852.00 seconds
Image has 169 counts for 5.9257E-02 counts/sec
Command not found; type ? for a command listing
!ad71043000s000202h:ASCA >
!ad71043000s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000s000202h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000s000202h:ASCA > read events ad71043000s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad71043000s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad71043000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000202h.img
Wrote image to file ad71043000s000202h.img
!ad71043000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad71043000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000202h_lo.img
Wrote image to file ad71043000s000202h_lo.img
!ad71043000s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad71043000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71043000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000202h_hi.img
Wrote image to file ad71043000s000202h_hi.img
!ad71043000s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad71043000s000302l.expo
ASCAEXPO_V0.9b
reading data file: ad71043000s000302l.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6301
Mean RA/DEC/ROLL : 150.3929 28.7553 65.6301
Pnt RA/DEC/ROLL : 150.3398 28.7540 65.6301
Image rebin factor : 4
Attitude Records : 17609
Hot Pixels : 7
GTI intervals : 1
Total GTI (secs) : 128.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 62.8793678 62.8793678
20 Percent Complete: Total/live time: 128.0000000 128.0000000
100 Percent Complete: Total/live time: 128.0000000 128.0000000
Number of attitude steps used: 2
Number of attitude steps avail: 11
Mean RA/DEC pixel offset: -25.8486 -47.1509
writing expo file: ad71043000s000302l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000s000302l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000s000302l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 7 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7 7 0 0 0 0
in 128.00 seconds
Image has 7 counts for 5.4688E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 6 0 0 0 1
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7 6 0 0 0 1
in 128.00 seconds
Image has 6 counts for 4.6875E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 1 0 0 0 6
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7 1 0 0 0 6
in 128.00 seconds
Image has 1 counts for 7.8125E-03 counts/sec
Command not found; type ? for a command listing
!ad71043000s000302l:ASCA >
!ad71043000s000302l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000s000302l:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000s000302l:ASCA > read events ad71043000s000302l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000s000302l:ASCA-SIS0-BRIGHT > set image sky
!ad71043000s000302l:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad71043000s000302l:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000302l:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000302l.img
Wrote image to file ad71043000s000302l.img
!ad71043000s000302l:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad71043000s000302l:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000302l:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000302l_lo.img
Wrote image to file ad71043000s000302l_lo.img
!ad71043000s000302l:ASCA-SIS0-BRIGHT > clear pha_cut
!ad71043000s000302l:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71043000s000302l:ASCA-SIS0-BRIGHT > extract image
!ad71043000s000302l:ASCA-SIS0-BRIGHT > save image outfile=ad71043000s000302l_hi.img
Wrote image to file ad71043000s000302l_hi.img
!ad71043000s000302l:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad71043000s100102m.expo
ASCAEXPO_V0.9b
reading data file: ad71043000s100102m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6236
Mean RA/DEC/ROLL : 150.3794 28.7637 65.6236
Pnt RA/DEC/ROLL : 150.2511 28.7102 65.6236
Image rebin factor : 4
Attitude Records : 17609
Hot Pixels : 32
GTI intervals : 14
Total GTI (secs) : 13389.751
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1774.9833984 1774.9833984
20 Percent Complete: Total/live time: 2814.9802246 2814.9802246
30 Percent Complete: Total/live time: 5678.9638672 5678.9638672
40 Percent Complete: Total/live time: 5678.9638672 5678.9638672
50 Percent Complete: Total/live time: 8334.9482422 8334.9482422
60 Percent Complete: Total/live time: 8334.9482422 8334.9482422
70 Percent Complete: Total/live time: 9549.7519531 9549.7519531
80 Percent Complete: Total/live time: 11060.6484375 11060.6484375
90 Percent Complete: Total/live time: 12877.7519531 12877.7519531
100 Percent Complete: Total/live time: 13389.7539062 13389.7539062
Number of attitude steps used: 51
Number of attitude steps avail: 4022
Mean RA/DEC pixel offset: 44.0563 -14.9244
writing expo file: ad71043000s100102m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000s100102m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000s100102m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.13E+05 794 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 794 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
794 794 0 0 0 0
in 13389.75 seconds
Image has 794 counts for 5.9299E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 277 0 0 0 517
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
794 277 0 0 0 517
in 13389.75 seconds
Image has 277 counts for 2.0687E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 517 0 0 0 277
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
794 517 0 0 0 277
in 13389.75 seconds
Image has 517 counts for 3.8612E-02 counts/sec
Command not found; type ? for a command listing
!ad71043000s100102m:ASCA >
!ad71043000s100102m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000s100102m:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000s100102m:ASCA > read events ad71043000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000s100102m:ASCA-SIS1-BRIGHT > set image sky
!ad71043000s100102m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad71043000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100102m.img
Wrote image to file ad71043000s100102m.img
!ad71043000s100102m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad71043000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100102m_lo.img
Wrote image to file ad71043000s100102m_lo.img
!ad71043000s100102m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad71043000s100102m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71043000s100102m:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100102m:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100102m_hi.img
Wrote image to file ad71043000s100102m_hi.img
!ad71043000s100102m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad71043000s100202h.expo
ASCAEXPO_V0.9b
reading data file: ad71043000s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa940504_0721.2000
making an exposure map...
Aspect RA/DEC/ROLL : 150.3660 28.7536 65.6211
Mean RA/DEC/ROLL : 150.3791 28.7603 65.6211
Pnt RA/DEC/ROLL : 150.3540 28.7481 65.6211
Image rebin factor : 4
Attitude Records : 17609
Hot Pixels : 238
GTI intervals : 5
Total GTI (secs) : 2858.035
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1525.9952393 1525.9952393
20 Percent Complete: Total/live time: 1525.9952393 1525.9952393
30 Percent Complete: Total/live time: 1535.4952393 1535.4952393
40 Percent Complete: Total/live time: 1535.4952393 1535.4952393
50 Percent Complete: Total/live time: 1560.9951172 1560.9951172
60 Percent Complete: Total/live time: 1868.9525146 1868.9525146
70 Percent Complete: Total/live time: 2858.0354004 2858.0354004
100 Percent Complete: Total/live time: 2858.0354004 2858.0354004
Number of attitude steps used: 11
Number of attitude steps avail: 6186
Mean RA/DEC pixel offset: -43.8185 -31.4165
writing expo file: ad71043000s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad71043000s100202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad71043000s100202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:25 0.29E+04 360 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.evt
Total Good Bad: Region Time Phase Cut
360 360 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
360 360 0 0 0 0
in 2858.04 seconds
Image has 360 counts for 0.1260 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.evt
Total Good Bad: Region Time Phase Cut
360 195 0 0 0 165
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
360 195 0 0 0 165
in 2858.04 seconds
Image has 195 counts for 6.8229E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.evt
Total Good Bad: Region Time Phase Cut
360 165 0 0 0 195
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
360 165 0 0 0 195
in 2858.04 seconds
Image has 165 counts for 5.7732E-02 counts/sec
Command not found; type ? for a command listing
!ad71043000s100202h:ASCA >
!ad71043000s100202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad71043000s100202h:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!ad71043000s100202h:ASCA > read events ad71043000s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!ad71043000s100202h:ASCA-SIS1-BRIGHT > set image sky
!ad71043000s100202h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad71043000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100202h.img
Wrote image to file ad71043000s100202h.img
!ad71043000s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad71043000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100202h_lo.img
Wrote image to file ad71043000s100202h_lo.img
!ad71043000s100202h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad71043000s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad71043000s100202h:ASCA-SIS1-BRIGHT > extract image
!ad71043000s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad71043000s100202h_hi.img
Wrote image to file ad71043000s100202h_hi.img
!ad71043000s100202h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad71043000s000102m.expo ad71043000s000202h.expo ad71043000s000302l.expo ad71043000s100102m.expo ad71043000s100202h.expo-> Summing the following images to produce ad71043000sis32002_all.totsky
ad71043000s000102m.img ad71043000s000202h.img ad71043000s000302l.img ad71043000s100102m.img ad71043000s100202h.img-> Summing the following images to produce ad71043000sis32002_lo.totsky
ad71043000s000102m_lo.img ad71043000s000202h_lo.img ad71043000s000302l_lo.img ad71043000s100102m_lo.img ad71043000s100202h_lo.img-> Summing the following images to produce ad71043000sis32002_hi.totsky
ad71043000s000102m_hi.img ad71043000s000202h_hi.img ad71043000s000302l_hi.img ad71043000s100102m_hi.img ad71043000s100202h_hi.img-> Running XIMAGE to create ad71043000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad71043000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 6.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 6 min: 0 ![2]XIMAGE> read/exp_map ad71043000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 545.760 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 545 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 3446 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 18.0000 18 0 ![9]XIMAGE> exit-> Summing gis images
ad71043000g200170m.expo ad71043000g200270h.expo ad71043000g300170m.expo ad71043000g300270h.expo-> Summing the following images to produce ad71043000gis25670_all.totsky
ad71043000g200170m.img ad71043000g200270h.img ad71043000g300170m.img ad71043000g300270h.img-> Summing the following images to produce ad71043000gis25670_lo.totsky
ad71043000g200170m_lo.img ad71043000g200270h_lo.img ad71043000g300170m_lo.img ad71043000g300270h_lo.img-> Summing the following images to produce ad71043000gis25670_hi.totsky
ad71043000g200170m_hi.img ad71043000g200270h_hi.img ad71043000g300170m_hi.img ad71043000g300270h_hi.img-> Running XIMAGE to create ad71043000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad71043000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 8.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 8 min: 0 ![2]XIMAGE> read/exp_map ad71043000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 601.930 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 601 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 56.0000 56 0 ![9]XIMAGE> exit
109 138 8.41737e-05 17 10 9.22841-> Smoothing ad71043000gis25670_hi.totsky with ad71043000gis25670.totexpo
109 138 6.6453e-05 92 10 12.7618-> Smoothing ad71043000gis25670_lo.totsky with ad71043000gis25670.totexpo
109 138 17 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad71043000gis25670.src
117 181 4.17628e-05 155 14 8.60382-> Smoothing ad71043000sis32002_hi.totsky with ad71043000sis32002.totexpo
118 182 2.37579e-05 154 19 12.2688-> Smoothing ad71043000sis32002_lo.totsky with ad71043000sis32002.totexpo
120 184 9.21873e-06 151 14 4.51487-> Determining extraction radii
117 181 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad71043000sis32002.src
The sum of the selected column is 44275.000 The mean of the selected column is 466.05263 The standard deviation of the selected column is 18.025613 The minimum of selected column is 426.00000 The maximum of selected column is 507.00000 The number of points used in calculation is 95-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 44549.000 The mean of the selected column is 468.93684 The standard deviation of the selected column is 17.070449 The minimum of selected column is 429.00000 The maximum of selected column is 505.00000 The number of points used in calculation is 95-> Converting (468.0,724.0,2.0) to s1 detector coordinates
The sum of the selected column is 40147.000 The mean of the selected column is 466.82558 The standard deviation of the selected column is 16.531746 The minimum of selected column is 432.00000 The maximum of selected column is 500.00000 The number of points used in calculation is 86-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 43870.000 The mean of the selected column is 510.11628 The standard deviation of the selected column is 18.616513 The minimum of selected column is 466.00000 The maximum of selected column is 551.00000 The number of points used in calculation is 86-> Converting (109.0,138.0,2.0) to g2 detector coordinates
The sum of the selected column is 2683.0000 The mean of the selected column is 107.32000 The standard deviation of the selected column is 1.1075498 The minimum of selected column is 105.00000 The maximum of selected column is 109.00000 The number of points used in calculation is 25-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2826.0000 The mean of the selected column is 113.04000 The standard deviation of the selected column is 1.3379088 The minimum of selected column is 110.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 25-> Converting (109.0,138.0,2.0) to g3 detector coordinates
The sum of the selected column is 2603.0000 The mean of the selected column is 113.17391 The standard deviation of the selected column is 1.1140497 The minimum of selected column is 111.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 23-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2612.0000 The mean of the selected column is 113.56522 The standard deviation of the selected column is 1.3425243 The minimum of selected column is 111.00000 The maximum of selected column is 116.00000 The number of points used in calculation is 23
1 ad71043000s000102m.evt 899 1 ad71043000s000302l.evt 899 2 ad71043000s000202h.evt 330-> Fetching SIS0_NOTCHIP0.1
ad71043000s000102m.evt ad71043000s000302l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
2 3C234 BRIGHT LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 460 432 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
899 464 435 0 0 0
in 13645.78 seconds
Spectrum has 464 counts for 3.4003E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13646. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.57813E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad71043000s000302l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad71043000s010102_1.pi group=yes
Wrote spectrum to ad71043000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71043000s010102_1.pi since it has 464 events1 ad71043000s000112m.evt 979 1 ad71043000s000312l.evt 979 2 ad71043000s000212h.evt 350-> SIS0_NOTCHIP0.1 already present in current directory
ad71043000s000112m.evt ad71043000s000312l.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.14E+05 972 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.14E+05 972 0100
2 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000112m.evt
Total Good Bad: Region Time Phase Cut
972 498 474 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000312l.evt
Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
979 502 477 0 0 0
in 13645.78 seconds
Spectrum has 502 counts for 3.6788E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13646. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.57813E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000s010212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000112m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad71043000s000312l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71043000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad71043000s010212_1.pi group=yes
Wrote spectrum to ad71043000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad71043000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 13646. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.57813E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 51 are grouped by a factor 26 ... 52 - 89 are grouped by a factor 19 ... 90 - 116 are grouped by a factor 27 ... 117 - 171 are grouped by a factor 55 ... 172 - 239 are grouped by a factor 68 ... 240 - 311 are grouped by a factor 72 ... 312 - 368 are grouped by a factor 57 ... 369 - 502 are grouped by a factor 134 ... 503 - 731 are grouped by a factor 229 ... --------------------------------------------- ... ...... exiting, changes written to file : ad71043000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad71043000s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 39 bins
expanded to 40 by 39 bins
First WMAP bin is at detector pixel 312 320
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.754 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 4.89000E+02
Weighted mean angle from optical axis = 5.861 arcmin
-> Standard Output From STOOL group_event_files:1 ad71043000s100102m.evt 794 2 ad71043000s100202h.evt 360-> Fetching SIS1_NOTCHIP0.1
ad71043000s100102m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.13E+05 794 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 410 384 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
794 410 384 0 0 0
in 13389.75 seconds
Spectrum has 410 counts for 3.0620E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13390. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.23340E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad71043000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad71043000s110102_1.pi group=yes
Wrote spectrum to ad71043000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71043000s110102_1.pi since it has 410 events1 ad71043000s100112m.evt 851 2 ad71043000s100212h.evt 381-> SIS1_NOTCHIP0.1 already present in current directory
ad71043000s100112m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.13E+05 851 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100112m.evt
Total Good Bad: Region Time Phase Cut
851 434 417 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
851 434 417 0 0 0
in 13389.75 seconds
Spectrum has 434 counts for 3.2413E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13390. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.23340E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000s110212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100112m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71043000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad71043000s110212_1.pi group=yes
Wrote spectrum to ad71043000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71043000s110212_1.pi since it has 434 events1 ad71043000g200170m.evt 4200 1 ad71043000g200270h.evt 4200-> GIS2_REGION256.4 already present in current directory
ad71043000g200170m.evt ad71043000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 728 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 284 3188 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 44 684 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4200 328 3872 0 0 0
in 18057.88 seconds
Spectrum has 328 counts for 1.8164E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18058. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.49689E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > read events ad71043000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad71043000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad71043000g210170_1.pi group=yes
Wrote spectrum to ad71043000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71043000g210170_1.pi since it has 328 events1 ad71043000g300170m.evt 4383 1 ad71043000g300270h.evt 4383-> GIS3_REGION256.4 already present in current directory
ad71043000g300170m.evt ad71043000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 756 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 273 3354 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 70 686 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4383 343 4040 0 0 0
in 18057.88 seconds
Spectrum has 343 counts for 1.8994E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18058. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.49689E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > read events ad71043000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad71043000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad71043000g310170_1.pi group=yes
Wrote spectrum to ad71043000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71043000g310170_1.pi since it has 343 events
XSPEC 9.01 05:18:19 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad71043000s010212_1.pi
Net count rate (cts/s) for file 1 3.6788E-02+/- 1.6823E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
2 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.29E+04 330 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
2 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.29E+04 330 1100
3 3C234 BRIGHT LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 461 431 0 0 0
Writing events file
461 events written to the output file
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.evt
Total Good Bad: Region Time Phase Cut
330 94 236 0 0 0
Writing events file
555 events written to the output file
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
Writing events file
559 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1229 559 670 0 0 0
in 16497.79 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad71043000s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad71043000s000302l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad71043000s000002_1.lc with binsize 1475.65175969693
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.16E+05 559 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/events.tmp
Total Good Bad: Region Time Phase Cut
559 559 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
559 559 0 0 0 0
in 16497.79 seconds
Fits light curve has 559 counts for 3.3883E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > set binsize 1475.65175969693
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad71043000s000002_1.lc
Wrote FITS light curve to file ad71043000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad71043000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71043000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ 3C234 Start Time (d) .... 9476 07:37:54.055
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9476 20:00:18.055
No. of Rows ....... 10 Bin Time (s) ...... 1476.
Right Ascension ... 1.5037E+02 Internal time sys.. Converted to TJD
Declination ....... 2.8754E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 31 Newbins of 1475.65 (s)
Intv 1 Start 9476 8:39:23
Ser.1 Avg 0.3347E-01 Chisq 4.488 Var 0.1173E-04 Newbs. 10
Min 0.2771E-01 Max 0.3810E-01expVar 0.2614E-04 Bins 10
Results from Statistical Analysis
Newbin Integration Time (s).. 1475.7
Interval Duration (s)........ 35416.
No. of Newbins .............. 10
Average (c/s) ............... 0.33471E-01 +/- 0.17E-02
Standard Deviation (c/s)..... 0.34254E-02
Minimum (c/s)................ 0.27708E-01
Maximum (c/s)................ 0.38098E-01
Variance ((c/s)**2).......... 0.11734E-04 +/- 0.55E-05
Expected Variance ((c/s)**2). 0.26142E-04 +/- 0.12E-04
Third Moment ((c/s)**3)......-0.69040E-08
Average Deviation (c/s)...... 0.29825E-02
Skewness.....................-0.17177 +/- 0.77
Kurtosis..................... -1.2887 +/- 1.5
RMS fractional variation....< 0.24459 (3 sigma)
Chi-Square................... 4.4884 dof 9
Chi-Square Prob of constancy. 0.87642 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.68066 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 31 Newbins of 1475.65 (s)
Intv 1 Start 9476 8:39:23
Ser.1 Avg 0.3347E-01 Chisq 4.488 Var 0.1173E-04 Newbs. 10
Min 0.2771E-01 Max 0.3810E-01expVar 0.2614E-04 Bins 10
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad71043000s100102m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.13E+05 794 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.13E+05 794 0001
2 3C234 BRIGHT HIGH 04/05/94 13:25:25 0.29E+04 360 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 411 383 0 0 0
Writing events file
411 events written to the output file
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.evt
Total Good Bad: Region Time Phase Cut
360 100 260 0 0 0
Writing events file
511 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1154 511 643 0 0 0
in 16247.79 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad71043000s100202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad71043000s100002_1.lc with binsize 1589.80302758836
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.16E+05 511 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/events.tmp
Total Good Bad: Region Time Phase Cut
511 511 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
511 511 0 0 0 0
in 16247.79 seconds
Fits light curve has 511 counts for 3.1450E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 1589.80302758836
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad71043000s100002_1.lc
Wrote FITS light curve to file ad71043000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad71043000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad71043000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ 3C234 Start Time (d) .... 9476 07:37:54.055
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9476 20:00:18.055
No. of Rows ....... 10 Bin Time (s) ...... 1590.
Right Ascension ... 1.5037E+02 Internal time sys.. Converted to TJD
Declination ....... 2.8754E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 29 Newbins of 1589.80 (s)
Intv 1 Start 9476 8:44: 8
Ser.1 Avg 0.3131E-01 Chisq 11.70 Var 0.2919E-04 Newbs. 10
Min 0.2326E-01 Max 0.3961E-01expVar 0.2495E-04 Bins 10
Results from Statistical Analysis
Newbin Integration Time (s).. 1589.8
Interval Duration (s)........ 34976.
No. of Newbins .............. 10
Average (c/s) ............... 0.31306E-01 +/- 0.17E-02
Standard Deviation (c/s)..... 0.54025E-02
Minimum (c/s)................ 0.23258E-01
Maximum (c/s)................ 0.39607E-01
Variance ((c/s)**2).......... 0.29187E-04 +/- 0.14E-04
Expected Variance ((c/s)**2). 0.24947E-04 +/- 0.12E-04
Third Moment ((c/s)**3)...... 0.30046E-07
Average Deviation (c/s)...... 0.48865E-02
Skewness..................... 0.19055 +/- 0.77
Kurtosis..................... -1.4304 +/- 1.5
RMS fractional variation....< 0.21658 (3 sigma)
Chi-Square................... 11.699 dof 9
Chi-Square Prob of constancy. 0.23083 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.12181 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 29 Newbins of 1589.80 (s)
Intv 1 Start 9476 8:44: 8
Ser.1 Avg 0.3131E-01 Chisq 11.70 Var 0.2919E-04 Newbs. 10
Min 0.2326E-01 Max 0.3961E-01expVar 0.2495E-04 Bins 10
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad71043000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 728 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 284 3188 0 0 0
Writing events file
284 events written to the output file
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 44 684 0 0 0
Writing events file
328 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4200 328 3872 0 0 0
in 18057.88 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > read events ad71043000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > filter region ad71043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> skipping ad71043000g200070_1.lc since it would have 328 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 756 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 273 3354 0 0 0
Writing events file
273 events written to the output file
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 70 686 0 0 0
Writing events file
343 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4383 343 4040 0 0 0
in 18057.88 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > read events ad71043000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > filter region ad71043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> skipping ad71043000g300070_1.lc since it would have 343 eventsad71043000g200170m.evt[2] ad71043000g200270h.evt[2]-> Making L1 light curve of ft940504_0721_2000G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5624 output records from 5628 good input G2_L1 records.-> Making L1 light curve of ft940504_0721_2000G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 15925 output records from 18876 good input G2_L1 records.-> Merging GTIs from the following files:
ad71043000g300170m.evt[2] ad71043000g300270h.evt[2]-> Making L1 light curve of ft940504_0721_2000G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5547 output records from 5551 good input G3_L1 records.-> Making L1 light curve of ft940504_0721_2000G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 15693 output records from 18573 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3472 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.evt
Total Good Bad: Region Time Phase Cut
3472 284 3188 0 0 0
Writing events file
284 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3472 284 3188 0 0 0
in 14927.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > filter region ad71043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71043000g200170m_1.ulc use_events=yes
Wrote events list to file ad71043000g200170m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71043000g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 728 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.evt
Total Good Bad: Region Time Phase Cut
728 44 684 0 0 0
Writing events file
44 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
728 44 684 0 0 0
in 3130.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > filter region ad71043000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad71043000g200270h_1.ulc use_events=yes
Wrote events list to file ad71043000g200270h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad71043000g300170m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.15E+05 3627 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.evt
Total Good Bad: Region Time Phase Cut
3627 273 3354 0 0 0
Writing events file
273 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3627 273 3354 0 0 0
in 14927.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > filter region ad71043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71043000g300170m_1.ulc use_events=yes
Wrote events list to file ad71043000g300170m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71043000g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.31E+04 756 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.evt
Total Good Bad: Region Time Phase Cut
756 70 686 0 0 0
Writing events file
70 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
756 70 686 0 0 0
in 3130.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > filter region ad71043000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad71043000g300270h_1.ulc use_events=yes
Wrote events list to file ad71043000g300270h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad71043000s000102m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.14E+05 892 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.evt
Total Good Bad: Region Time Phase Cut
892 461 431 0 0 0
Writing events file
461 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
892 461 431 0 0 0
in 13517.78 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000102m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad71043000s000102m_1.ulc use_events=yes
Wrote events list to file ad71043000s000102m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71043000s000112m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.14E+05 972 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000112m.evt
Total Good Bad: Region Time Phase Cut
972 499 473 0 0 0
Writing events file
499 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 499 473 0 0 0
in 13517.78 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000112m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad71043000s000112m_1.ulc use_events=yes
Wrote events list to file ad71043000s000112m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad71043000s000202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.29E+04 330 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.evt
Total Good Bad: Region Time Phase Cut
330 94 236 0 0 0
Writing events file
94 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
330 94 236 0 0 0
in 2852.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad71043000s000202h_1.ulc use_events=yes
Wrote events list to file ad71043000s000202h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71043000s000212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:29 0.29E+04 350 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000212h.evt
Total Good Bad: Region Time Phase Cut
350 100 250 0 0 0
Writing events file
100 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
350 100 250 0 0 0
in 2852.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad71043000s000212h_1.ulc use_events=yes
Wrote events list to file ad71043000s000212h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad71043000s000302l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.evt
Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
Writing events file
4 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000302l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad71043000s000302l_1.ulc use_events=yes
Wrote events list to file ad71043000s000302l_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71043000s000302l_1.ulc since it has 4 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.13E+03 7 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000312l.evt
Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
Writing events file
4 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7 4 3 0 0 0
in 128.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s000312l.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad71043000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad71043000s000312l_1.ulc use_events=yes
Wrote events list to file ad71043000s000312l_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71043000s000312l_1.ulc since it has 4 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.13E+05 794 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.evt
Total Good Bad: Region Time Phase Cut
794 411 383 0 0 0
Writing events file
411 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
794 411 383 0 0 0
in 13389.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100102m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad71043000s100102m_1.ulc use_events=yes
Wrote events list to file ad71043000s100102m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71043000s100112m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.13E+05 851 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100112m.evt
Total Good Bad: Region Time Phase Cut
851 435 416 0 0 0
Writing events file
435 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
851 435 416 0 0 0
in 13389.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100112m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad71043000s100112m_1.ulc use_events=yes
Wrote events list to file ad71043000s100112m_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad71043000s100202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:25 0.29E+04 360 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.evt
Total Good Bad: Region Time Phase Cut
360 100 260 0 0 0
Writing events file
100 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
360 100 260 0 0 0
in 2858.04 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad71043000s100202h_1.ulc use_events=yes
Wrote events list to file ad71043000s100202h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad71043000s100212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:25 0.29E+04 381 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100212h.evt
Total Good Bad: Region Time Phase Cut
381 106 275 0 0 0
Writing events file
106 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
381 106 275 0 0 0
in 2858.04 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000s100212h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad71043000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad71043000s100212h_1.ulc use_events=yes
Wrote events list to file ad71043000s100212h_1.ulc
Changing Data directory from:
/data/data15/seq_proc/71043000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 4368 Total of 0 sets of frame data are extracted.
1 ad71043000g200170m.unf 29427 1 ad71043000g200270h.unf 29427 1 ad71043000g200370l.unf 29427-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2664 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2664 1024
3 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1989 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.unf
Total Good Bad: Region Time Phase Cut
24774 8837 15937 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.unf
Total Good Bad: Region Time Phase Cut
2664 1000 1664 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200370l.unf
Total Good Bad: Region Time Phase Cut
1989 774 1215 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
29427 10611 18816 0 0 0
in 39833.88 seconds
Spectrum has 10611 counts for 0.2664 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 39834. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > read events ad71043000g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > read events ad71043000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad71043000g220170.cal group=yes
Wrote spectrum to ad71043000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Fetching gis2v4_0.rmf
XSPEC 9.01 05:34:50 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad71043000g220170.cal
Net count rate (cts/s) for file 1 0.2664 +/- 2.5872E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.5569E+05 using 84 PHA bins.
Reduced chi-squared = 1.1113E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.4939E+05 using 84 PHA bins.
Reduced chi-squared = 1.0890E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.4939E+05 using 84 PHA bins.
Reduced chi-squared = 1.0752E+04
!XSPEC> renorm
Chi-Squared = 3345. using 84 PHA bins.
Reduced chi-squared = 42.35
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2589.9 0 1.000 5.893 0.1055 8.6709E-02
7.5428E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
873.03 0 1.000 5.863 0.1546 0.1329
6.5844E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
237.98 -1 1.000 5.906 0.1680 0.1876
4.3926E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
205.27 -2 1.000 5.927 0.1767 0.2028
3.4475E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
203.67 -3 1.000 5.922 0.1714 0.2008
3.6480E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
203.64 -4 1.000 5.923 0.1722 0.2013
3.5947E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
203.62 -5 1.000 5.923 0.1719 0.2012
3.6073E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
203.62 0 1.000 5.923 0.1719 0.2012
3.6072E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92265 +/- 0.49061E-02
3 3 2 gaussian/b Sigma 0.171913 +/- 0.54004E-02
4 4 2 gaussian/b norm 0.201167 +/- 0.28212E-02
5 2 3 gaussian/b LineE 6.52087 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.180386 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.607185E-02 +/- 0.19182E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 203.6 using 84 PHA bins.
Reduced chi-squared = 2.577
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad71043000g220170.cal peaks at 5.92265 +/- 0.0049061 keV1 ad71043000g300170m.unf 27672 1 ad71043000g300270h.unf 27672 1 ad71043000g300370l.unf 27672-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2552 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
2 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2552 1024
3 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.unf
Total Good Bad: Region Time Phase Cut
23308 8079 15229 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.unf
Total Good Bad: Region Time Phase Cut
2552 924 1628 0 0 0
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300370l.unf
Total Good Bad: Region Time Phase Cut
1812 634 1178 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27672 9637 18035 0 0 0
in 39833.88 seconds
Spectrum has 9637 counts for 0.2419 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 39834. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad71043000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!xsel:ASCA > read events ad71043000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > read events ad71043000g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > read events ad71043000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad71043000g320170.cal group=yes
Wrote spectrum to ad71043000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Fetching gis3v4_0.rmf
XSPEC 9.01 05:35:55 17-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad71043000g320170.cal
Net count rate (cts/s) for file 1 0.2419 +/- 2.4666E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.8978E+05 using 84 PHA bins.
Reduced chi-squared = 1.2854E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.7963E+05 using 84 PHA bins.
Reduced chi-squared = 1.2559E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.7963E+05 using 84 PHA bins.
Reduced chi-squared = 1.2400E+04
!XSPEC> renorm
Chi-Squared = 3409. using 84 PHA bins.
Reduced chi-squared = 43.16
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2705.6 0 1.000 5.892 8.8129E-02 7.7863E-02
6.6586E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
929.34 0 1.000 5.860 0.1357 0.1238
5.7795E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
234.70 -1 1.000 5.907 0.1404 0.1749
3.8525E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
142.10 -2 1.000 5.942 0.1621 0.1951
2.7038E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
141.65 -3 1.000 5.943 0.1616 0.1960
2.6352E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
141.64 -4 1.000 5.943 0.1614 0.1960
2.6384E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94275 +/- 0.44887E-02
3 3 2 gaussian/b Sigma 0.161449 +/- 0.52357E-02
4 4 2 gaussian/b norm 0.195975 +/- 0.26116E-02
5 2 3 gaussian/b LineE 6.54300 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.169406 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.638401E-02 +/- 0.15584E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 141.6 using 84 PHA bins.
Reduced chi-squared = 1.793
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad71043000g320170.cal peaks at 5.94275 +/- 0.0044887 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.32E+05 44002 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000102m.unf
Total Good Bad: Region Time Phase Cut
44002 10112 0 33890 0 0
Writing events file
10112 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44002 10112 0 33890 0 0
in 6119.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000102m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71043000s000102m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s000102m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 10112
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 9176
Flickering pixels iter, pixels & cnts : 1 10 141
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 22
Number of (internal) image counts : 10112
Number of image cts rejected (N, %) : 9317 92.1380539
By chip : 0 1 2 3
Pixels rejected : 0 22 0 0
Image counts : 0 10112 0 0
Image cts rejected: 0 9317 0 0
Image cts rej (%) : 0.00 92.14 0.00 0.00
filtering data...
Total counts : 0 10112 0 0
Total cts rejected: 0 9317 0 0
Total cts rej (%) : 0.00 92.14 0.00 0.00
Number of clean counts accepted : 795
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 22
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s000112m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.32E+05 44499 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000112m.unf
Total Good Bad: Region Time Phase Cut
44499 10264 0 34235 0 0
Writing events file
10264 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44499 10264 0 34235 0 0
in 6119.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000112m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad71043000s000112m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s000112m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 10264
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 9176
Flickering pixels iter, pixels & cnts : 1 10 141
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 22
Number of (internal) image counts : 10264
Number of image cts rejected (N, %) : 9317 90.7735748
By chip : 0 1 2 3
Pixels rejected : 0 22 0 0
Image counts : 0 10264 0 0
Image cts rejected: 0 9317 0 0
Image cts rej (%) : 0.00 90.77 0.00 0.00
filtering data...
Total counts : 0 10264 0 0
Total cts rejected: 0 9317 0 0
Total cts rej (%) : 0.00 90.77 0.00 0.00
Number of clean counts accepted : 947
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 22
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:29 0.33E+04 46007 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000s000202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad71043000s000202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:29 0.33E+04 46138 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000s000212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad71043000s000212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.37E+04 1025 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000302l.unf
Total Good Bad: Region Time Phase Cut
1025 12 0 1013 0 0
Writing events file
12 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1025 12 0 1013 0 0
in 6.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71043000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 12
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 12 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 12 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 12
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s000312l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.37E+04 1036 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s000312l.unf
Total Good Bad: Region Time Phase Cut
1036 12 0 1024 0 0
Writing events file
12 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1036 12 0 1024 0 0
in 6.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s000312l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad71043000s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 0 0
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 12
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 12 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 12 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 12
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s100102m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT MEDIUM 04/05/94 07:21:48 0.32E+05 117309 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100102m.unf
Total Good Bad: Region Time Phase Cut
117309 24815 0 92494 0 0
Writing events file
24815 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
117309 24815 0 92494 0 0
in 6119.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100102m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71043000s100102m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s100102m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 24815
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 22 23914
Flickering pixels iter, pixels & cnts : 1 11 153
Number of pixels rejected : 33
Number of (internal) image counts : 24815
Number of image cts rejected (N, %) : 24067 96.9856949
By chip : 0 1 2 3
Pixels rejected : 0 0 0 33
Image counts : 0 0 0 24815
Image cts rejected: 0 0 0 24067
Image cts rej (%) : 0.00 0.00 0.00 96.99
filtering data...
Total counts : 0 0 0 24815
Total cts rejected: 0 0 0 24067
Total cts rej (%) : 0.00 0.00 0.00 96.99
Number of clean counts accepted : 748
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 33
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s100112m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 MEDIUM 04/05/94 07:21:48 0.32E+05 117637 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100112m.unf
Total Good Bad: Region Time Phase Cut
117637 24908 0 92729 0 0
Writing events file
24908 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
117637 24908 0 92729 0 0
in 6119.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100112m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad71043000s100112m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s100112m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 24908
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 22 23914
Flickering pixels iter, pixels & cnts : 1 11 153
Number of pixels rejected : 33
Number of (internal) image counts : 24908
Number of image cts rejected (N, %) : 24067 96.6235733
By chip : 0 1 2 3
Pixels rejected : 0 0 0 33
Image counts : 0 0 0 24908
Image cts rejected: 0 0 0 24067
Image cts rej (%) : 0.00 0.00 0.00 96.62
filtering data...
Total counts : 0 0 0 24908
Total cts rejected: 0 0 0 24067
Total cts rej (%) : 0.00 0.00 0.00 96.62
Number of clean counts accepted : 841
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 33
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s100202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT HIGH 04/05/94 13:25:25 0.33E+04 53287 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000s100202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad71043000s100202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 HIGH 04/05/94 13:25:25 0.33E+04 53347 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000s100212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad71043000s100212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT LOW 04/05/94 16:03:55 0.37E+04 2918 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100302l.unf
Total Good Bad: Region Time Phase Cut
2918 14 0 2904 0 0
Writing events file
14 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2918 14 0 2904 0 0
in 6.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad71043000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 14
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 14
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 14
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 14
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 14
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000s100312l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 3C234 BRIGHT2 LOW 04/05/94 16:03:55 0.37E+04 2923 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000s100312l.unf
Total Good Bad: Region Time Phase Cut
2923 14 0 2909 0 0
Writing events file
14 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2923 14 0 2909 0 0
in 6.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad71043000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad71043000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 14
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 14
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 14
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 14
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 14
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad71043000g200170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.unf
Total Good Bad: Region Time Phase Cut
24774 3666 0 21108 0 0
Writing events file
3666 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24774 3666 0 21108 0 0
in 5583.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad71043000g200170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 24774 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200170m.unf
Total Good Bad: Region Time Phase Cut
24774 3773 0 21001 0 0
Writing events file
3773 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24774 3773 0 21001 0 0
in 4767.79 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71043000g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2664 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71043000g200270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2664 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71043000g200270h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1989 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200370l.unf
Total Good Bad: Region Time Phase Cut
1989 0 0 1989 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1989 0 0 1989 0 0
in 0.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad71043000g200370l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1989 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g200370l.unf
Total Good Bad: Region Time Phase Cut
1989 1984 0 5 0 0
Writing events file
1984 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1989 1984 0 5 0 0
in 2528.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71043000g300170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.unf
Total Good Bad: Region Time Phase Cut
23308 3342 0 19966 0 0
Writing events file
3342 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23308 3342 0 19966 0 0
in 5583.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad71043000g300170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH MEDIUM 04/05/94 07:21:54 0.33E+05 23308 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300170m.unf
Total Good Bad: Region Time Phase Cut
23308 3490 0 19818 0 0
Writing events file
3490 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23308 3490 0 19818 0 0
in 4767.79 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad71043000g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2552 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71043000g300270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH HIGH 04/05/94 13:25:35 0.40E+04 2552 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data15/seq_proc/71043000.005/ad71043000g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71043000g300270h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300370l.unf
Total Good Bad: Region Time Phase Cut
1812 0 0 1812 0 0
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1812 0 0 1812 0 0
in 0.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad71043000g300370l.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 3C234 PH LOW 04/05/94 16:04:01 0.26E+04 1812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data15/seq_proc/71043000.005/ad71043000g300370l.unf
Total Good Bad: Region Time Phase Cut
1812 1809 0 3 0 0
Writing events file
1809 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1812 1809 0 3 0 0
in 2528.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data15/seq_proc/71043000.005/
Setting mkf directory to /data/data15/seq_proc/71043000.005/
!earthevents:ASCA > read events ad71043000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data15/seq_proc/71043000.005/
HK Directory is: /data/data15/seq_proc/71043000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files