The following information is also available:
Time column is TIME ORDERED-> Fetching fa961113_0714.1230.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 122022891.671600 122041850.615300
Data file start and stop ascatime : 122022891.671600 122041850.615300
Aspecting run start and stop ascatime : 122022891.671674 122041850.615188
Time interval averaged over (seconds) : 18958.943515
Total pointing and manuver time (sec) : 16675.958984 2282.994873
Mean boresight Euler angles : 339.156103 115.890360 205.439823
RA DEC SUN ANGLE
Mean solar position (deg) : 227.86 -17.82
Mean aberration (arcsec) : 6.24 -3.62
Mean sat X-axis (deg) : 291.706069 54.331112 90.23
Mean sat Y-axis (deg) : 237.422102 -22.733675 10.23
Mean sat Z-axis (deg) : 339.156103 -25.890360 100.22
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 338.966522 -26.117876 115.348854 3.350972
Minimum 338.707977 -26.139473 115.233253 0.037682
Maximum 339.088715 -25.716406 115.464119 72.823982
Sigma (RMS) 0.008340 0.002953 0.049878 0.908628
Number of ASPECT records processed = 13312
Aspecting to RA/DEC : 338.96652222 -26.11787605
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 122031074.64720 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 338.967 DEC: -26.118
START TIME: SC 122022891.6717 = UT 13/11/96 07:14:51
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500091 3.797 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
4.000093 4.811 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
6.500099 5.828 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
87.499901 4.826 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
370.998871 3.825 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
2250.993408 3.706 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
2565.492432 2.697 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2611.492188 1.686 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2657.992188 0.683 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2841.991699 1.683 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
3112.990723 2.686 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
4342.987305 3.201 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
7996.976074 3.498 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
17654.947266 3.162 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
18950.943359 27.838 9403 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0
18958.943359 72.824 9C03 1 1 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0
Attitude Records: 13312
Attitude Steps: 16
Maneuver ACM time: 2283.00 sec
Pointed ACM time: 16676.0 sec
-> Calculating aspect point67 62 count=1 sum1=338.897 sum2=115.489 sum3=205.407 87 104 count=4878 sum1=1.65412e+06 sum2=565414 sum3=1.00189e+06 88 104 count=2547 sum1=863699 sum2=295222 sum3=523143 89 103 count=20 sum1=6782.42 sum2=2318.08 sum3=4108.14 89 104 count=349 sum1=118351 sum2=40451.3 sum3=71685.7 90 103 count=163 sum1=55277.6 sum2=18892.1 sum3=33482.2 91 103 count=105 sum1=35609.2 sum2=12169.4 sum3=21569 92 102 count=6 sum1=2034.9 sum2=695.358 sum3=1232.59 92 103 count=82 sum1=27809.9 sum2=9503.42 sum3=16845 93 102 count=76 sum1=25775.8 sum2=8807.73 sum3=15613.1 94 102 count=60 sum1=20350 sum2=6953.24 sum3=12326.7 95 101 count=40 sum1=13567.1 sum2=4635.3 sum3=8218.17 95 102 count=15 sum1=5087.59 sum2=1738.28 sum3=3081.74 96 101 count=50 sum1=16959.3 sum2=5793.98 sum3=10273.1 97 101 count=48 sum1=16281.4 sum2=5562.04 sum3=9862.6 98 100 count=56 sum1=18995.5 sum2=6488.86 sum3=11506.8 98 101 count=4 sum1=1356.8 sum2=463.5 sum3=821.904 99 100 count=3832 sum1=1.29989e+06 sum2=444001 sum3=787454 100 100 count=630 sum1=213711 sum2=72996.4 sum3=129464 101 100 count=170 sum1=57670.1 sum2=19697.7 sum3=34936.3 102 100 count=123 sum1=41727.3 sum2=14252 sum3=25278.3 103 100 count=34 sum1=11534.7 sum2=3939.61 sum3=6987.79 104 100 count=8 sum1=2714.12 sum2=926.982 sum3=1644.27 105 100 count=6 sum1=2035.64 sum2=695.243 sum3=1233.25 105 101 count=7 sum1=2374.94 sum2=811.125 sum3=1438.82 1 out of 13311 points outside bin structure-> Euler angles: 339.1, 115.911, 205.391
Interpolating 46 records in time interval 1.22042e+08 - 1.22042e+08 Interpolating 74 records in time interval 1.22042e+08 - 1.22042e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft961113_0714.1230",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft961113_0714.1230 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 2 (ACS) Initial sis = 1 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 201248 Bright = 12000 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 212224 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 3338 no. of SIS events found = 133294-> Removing the following files with NEVENTS=0
ft961113_0714_1230G200199.fits ft961113_0714_1230G200370H.fits ft961113_0714_1230G200470H.fits ft961113_0714_1230G200570H.fits ft961113_0714_1230G200973H.fits ft961113_0714_1230G201270H.fits ft961113_0714_1230G201370M.fits ft961113_0714_1230G201899.fits ft961113_0714_1230G300199.fits ft961113_0714_1230G300570H.fits ft961113_0714_1230G300670H.fits ft961113_0714_1230G301073H.fits ft961113_0714_1230G301370H.fits ft961113_0714_1230G301470M.fits ft961113_0714_1230G301999.fits ft961113_0714_1230S000199.fits ft961113_0714_1230S000399.fits ft961113_0714_1230S000502H.fits ft961113_0714_1230S000802M.fits ft961113_0714_1230S001299.fits ft961113_0714_1230S100199.fits ft961113_0714_1230S100399.fits ft961113_0714_1230S100502H.fits ft961113_0714_1230S100802M.fits ft961113_0714_1230S101299.fits-> Checking for empty GTI extensions
ft961113_0714_1230S000201H.fits[3] ft961113_0714_1230S000401H.fits[3] ft961113_0714_1230S000602M.fits[3] ft961113_0714_1230S000702M.fits[3] ft961113_0714_1230S000901M.fits[3] ft961113_0714_1230S001001H.fits[3] ft961113_0714_1230S001102M.fits[3]-> Merging GTIs from the following files:
ft961113_0714_1230S100201H.fits[3] ft961113_0714_1230S100401H.fits[3] ft961113_0714_1230S100602M.fits[3] ft961113_0714_1230S100702M.fits[3] ft961113_0714_1230S100901M.fits[3] ft961113_0714_1230S101001H.fits[3] ft961113_0714_1230S101102M.fits[3]-> Merging GTIs from the following files:
ft961113_0714_1230G200270H.fits[3] ft961113_0714_1230G200670H.fits[3] ft961113_0714_1230G200770H.fits[3] ft961113_0714_1230G200870H.fits[3] ft961113_0714_1230G201070H.fits[3] ft961113_0714_1230G201170H.fits[3] ft961113_0714_1230G201470M.fits[3] ft961113_0714_1230G201570M.fits[3] ft961113_0714_1230G201670H.fits[3] ft961113_0714_1230G201770M.fits[3]-> Merging GTIs from the following files:
ft961113_0714_1230G300270H.fits[3] ft961113_0714_1230G300370H.fits[3] ft961113_0714_1230G300470H.fits[3] ft961113_0714_1230G300770H.fits[3] ft961113_0714_1230G300870H.fits[3] ft961113_0714_1230G300970H.fits[3] ft961113_0714_1230G301170H.fits[3] ft961113_0714_1230G301270H.fits[3] ft961113_0714_1230G301570M.fits[3] ft961113_0714_1230G301670M.fits[3] ft961113_0714_1230G301770H.fits[3] ft961113_0714_1230G301870M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 3 photon cnt = 3311 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 2583 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 739 GISSORTSPLIT:LO:Total filenames split = 10 GISSORTSPLIT:LO:Total split file cnt = 7 GISSORTSPLIT:LO:End program-> Creating ad74059010g200170h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G200270H.fits 2 -- ft961113_0714_1230G200870H.fits 3 -- ft961113_0714_1230G201670H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G200270H.fits 2 -- ft961113_0714_1230G200870H.fits 3 -- ft961113_0714_1230G201670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft961113_0714_1230G201070H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G201070H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G201070H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad74059010g200370m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G201570M.fits 2 -- ft961113_0714_1230G201770M.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G201570M.fits 2 -- ft961113_0714_1230G201770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000012 events
ft961113_0714_1230G201470M.fits-> Ignoring the following files containing 000000003 events
ft961113_0714_1230G200770H.fits-> Ignoring the following files containing 000000001 events
ft961113_0714_1230G200670H.fits-> Ignoring the following files containing 000000001 events
ft961113_0714_1230G201170H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300570h.prelist merge count = 3 photon cnt = 3261 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 2714 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g300270m.prelist merge count = 2 photon cnt = 725 GISSORTSPLIT:LO:Total filenames split = 12 GISSORTSPLIT:LO:Total split file cnt = 9 GISSORTSPLIT:LO:End program-> Creating ad74059010g300170h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G300270H.fits 2 -- ft961113_0714_1230G300970H.fits 3 -- ft961113_0714_1230G301770H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G300270H.fits 2 -- ft961113_0714_1230G300970H.fits 3 -- ft961113_0714_1230G301770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft961113_0714_1230G301170H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G301170H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G301170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad74059010g300370m.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230G301670M.fits 2 -- ft961113_0714_1230G301870M.fits Merging binary extension #: 2 1 -- ft961113_0714_1230G301670M.fits 2 -- ft961113_0714_1230G301870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000013 events
ft961113_0714_1230G301570M.fits-> Ignoring the following files containing 000000010 events
ft961113_0714_1230G300470H.fits-> Ignoring the following files containing 000000003 events
ft961113_0714_1230G300870H.fits-> Ignoring the following files containing 000000002 events
ft961113_0714_1230G300770H.fits-> Ignoring the following files containing 000000001 events
ft961113_0714_1230G300370H.fits-> Ignoring the following files containing 000000001 events
ft961113_0714_1230G301270H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 3 photon cnt = 64718 SIS0SORTSPLIT:LO:s000201m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:s000302m.prelist merge count = 2 photon cnt = 649 SIS0SORTSPLIT:LO:s000402m.prelist merge count = 1 photon cnt = 8 SIS0SORTSPLIT:LO:Total filenames split = 7 SIS0SORTSPLIT:LO:Total split file cnt = 4 SIS0SORTSPLIT:LO:End program-> Creating ad74059010s000101h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230S000201H.fits 2 -- ft961113_0714_1230S000401H.fits 3 -- ft961113_0714_1230S001001H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230S000201H.fits 2 -- ft961113_0714_1230S000401H.fits 3 -- ft961113_0714_1230S001001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000649 events
ft961113_0714_1230S000602M.fits ft961113_0714_1230S001102M.fits-> Ignoring the following files containing 000000032 events
ft961113_0714_1230S000901M.fits-> Ignoring the following files containing 000000008 events
ft961113_0714_1230S000702M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 3 photon cnt = 66855 SIS1SORTSPLIT:LO:s100201m.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:s100302m.prelist merge count = 2 photon cnt = 986 SIS1SORTSPLIT:LO:s100402m.prelist merge count = 1 photon cnt = 14 SIS1SORTSPLIT:LO:Total filenames split = 7 SIS1SORTSPLIT:LO:Total split file cnt = 4 SIS1SORTSPLIT:LO:End program-> Creating ad74059010s100101h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft961113_0714_1230S100201H.fits 2 -- ft961113_0714_1230S100401H.fits 3 -- ft961113_0714_1230S101001H.fits Merging binary extension #: 2 1 -- ft961113_0714_1230S100201H.fits 2 -- ft961113_0714_1230S100401H.fits 3 -- ft961113_0714_1230S101001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000986 events
ft961113_0714_1230S100602M.fits ft961113_0714_1230S101102M.fits-> Ignoring the following files containing 000000032 events
ft961113_0714_1230S100901M.fits-> Ignoring the following files containing 000000014 events
ft961113_0714_1230S100702M.fits-> Tar-ing together the leftover raw files
a ft961113_0714_1230G200670H.fits 40K a ft961113_0714_1230G200770H.fits 40K a ft961113_0714_1230G201170H.fits 40K a ft961113_0714_1230G201470M.fits 40K a ft961113_0714_1230G300370H.fits 40K a ft961113_0714_1230G300470H.fits 40K a ft961113_0714_1230G300770H.fits 40K a ft961113_0714_1230G300870H.fits 40K a ft961113_0714_1230G301270H.fits 40K a ft961113_0714_1230G301570M.fits 40K a ft961113_0714_1230S000602M.fits 45K a ft961113_0714_1230S000702M.fits 40K a ft961113_0714_1230S000901M.fits 40K a ft961113_0714_1230S001102M.fits 51K a ft961113_0714_1230S100602M.fits 48K a ft961113_0714_1230S100702M.fits 40K a ft961113_0714_1230S100901M.fits 40K a ft961113_0714_1230S101102M.fits 57K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft961113_0714.1230 'ft961113_0714.1230' is successfully opened Data Start Time is 122022889.67 (961113 071449) Time Margin 2.0 sec included 'ft961113_0714.1230' EOF detected, sf=3338 Data End Time is 122041847.62 (961113 123047) Gain History is written in ft961113_0714_1230.ghf-> Checking if column CAL_START in ft961113_0714_1230.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft961113_0714_1230.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad74059010g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010g200370m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 122031074.64720 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad74059010g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010g300370m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 122031074.64720 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad74059010s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad74059010s100112h.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 96/11/13 7:14 mjd=50400.301389 Orbit file name is ./frf.orbit.215 Epoch of Orbital Elements: 1996/11/11 9:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa961113_0714.1230 S0-HK file: ft961113_0714_1230S0HK.fits S1-HK file: ft961113_0714_1230S1HK.fits G2-HK file: ft961113_0714_1230G2HK.fits G3-HK file: ft961113_0714_1230G3HK.fits output FITS File: ft961113_0714_1230.mkf Total 593 Data bins were processed.-> Checking if column TIME in ft961113_0714_1230.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 591.40789 The mean of the selected column is 17.394350 The standard deviation of the selected column is 7.2005958 The minimum of selected column is 6.2500186 The maximum of selected column is 38.125114 The number of points used in calculation is 34-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<38.9 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.56E+04 4097 0100
Processing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3695 1948 0 1747 0 0
Writing events file
1948 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3695 1948 0 1747 0 0
in 2203.84 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/74059010.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/74059010.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1948
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 785
Flickering pixels iter, pixels & cnts : 1 2 17
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 1948
Number of image cts rejected (N, %) : 802 41.1704330
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 1948 0 0
Image cts rejected: 0 802 0 0
Image cts rej (%) : 0.00 41.17 0.00 0.00
filtering data...
Total counts : 0 1948 0 0
Total cts rejected: 0 802 0 0
Total cts rej (%) : 0.00 41.17 0.00 0.00
Number of clean counts accepted : 1146
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad74059010s000102h.evt use_events=no
Wrote cleaned events file to ad74059010s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad74059010s000112h.unf into ad74059010s000112h.evtThe sum of the selected column is 591.40789 The mean of the selected column is 17.394350 The standard deviation of the selected column is 7.2005958 The minimum of selected column is 6.2500186 The maximum of selected column is 38.125114 The number of points used in calculation is 34-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<38.9 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.56E+04 4167 0100
Processing file: /data/data19/seq_proc/74059010.008/ad74059010s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3744 1975 0 1769 0 0
Writing events file
1975 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3744 1975 0 1769 0 0
in 2203.84 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/74059010.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/74059010.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1975
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 785
Flickering pixels iter, pixels & cnts : 1 2 17
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 1975
Number of image cts rejected (N, %) : 802 40.6075935
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 1975 0 0
Image cts rejected: 0 802 0 0
Image cts rej (%) : 0.00 40.61 0.00 0.00
filtering data...
Total counts : 0 1975 0 0
Total cts rejected: 0 802 0 0
Total cts rej (%) : 0.00 40.61 0.00 0.00
Number of clean counts accepted : 1173
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad74059010s000112h.evt use_events=no
Wrote cleaned events file to ad74059010s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad74059010s100101h.unf because of modeThe sum of the selected column is 880.60681 The mean of the selected column is 27.518963 The standard deviation of the selected column is 13.547224 The minimum of selected column is 6.1042094 The maximum of selected column is 79.718987 The number of points used in calculation is 32-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<68.1 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.56E+04 7840 0001
Processing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
6358 3124 0 3234 0 0
Writing events file
3124 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6358 3124 0 3234 0 0
in 2159.84 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/74059010.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/74059010.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3124
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 2147
Flickering pixels iter, pixels & cnts : 1 1 5
Number of pixels rejected : 10
Number of (internal) image counts : 3124
Number of image cts rejected (N, %) : 2152 68.8860397
By chip : 0 1 2 3
Pixels rejected : 0 0 0 10
Image counts : 0 0 0 3124
Image cts rejected: 0 0 0 2152
Image cts rej (%) : 0.00 0.00 0.00 68.89
filtering data...
Total counts : 0 0 0 3124
Total cts rejected: 0 0 0 2152
Total cts rej (%) : 0.00 0.00 0.00 68.89
Number of clean counts accepted : 972
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad74059010s100102h.evt use_events=no
Wrote cleaned events file to ad74059010s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad74059010s100112h.unf into ad74059010s100112h.evtThe sum of the selected column is 880.60681 The mean of the selected column is 27.518963 The standard deviation of the selected column is 13.547224 The minimum of selected column is 6.1042094 The maximum of selected column is 79.718987 The number of points used in calculation is 32-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<68.1 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.56E+04 7880 0001
Processing file: /data/data19/seq_proc/74059010.008/ad74059010s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
6382 3139 0 3243 0 0
Writing events file
3139 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6382 3139 0 3243 0 0
in 2159.84 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data19/seq_proc/74059010.008/screen_in_event.xsl
reading data file: /data/data19/seq_proc/74059010.008/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3139
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 2147
Flickering pixels iter, pixels & cnts : 1 1 5
Number of pixels rejected : 10
Number of (internal) image counts : 3139
Number of image cts rejected (N, %) : 2152 68.5568619
By chip : 0 1 2 3
Pixels rejected : 0 0 0 10
Image counts : 0 0 0 3139
Image cts rejected: 0 0 0 2152
Image cts rej (%) : 0.00 0.00 0.00 68.56
filtering data...
Total counts : 0 0 0 3139
Total cts rejected: 0 0 0 2152
Total cts rej (%) : 0.00 0.00 0.00 68.56
Number of clean counts accepted : 987
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad74059010s100112h.evt use_events=no
Wrote cleaned events file to ad74059010s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad74059010g200170h.unf into ad74059010g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.unf
Total Good Bad: Region Time Phase Cut
3311 1123 1538 650 0 0
Writing events file
1123 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3311 1123 1538 650 0 0
in 1477.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
1123 1058 65
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad74059010g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 1058 in ad74059010g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2583 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.unf
Total Good Bad: Region Time Phase Cut
2583 527 1180 876 0 0
Writing events file
527 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2583 527 1180 876 0 0
in 991.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
527 493 34
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad74059010g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 493 in ad74059010g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 739 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.unf
Total Good Bad: Region Time Phase Cut
739 221 342 176 0 0
Writing events file
221 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
739 221 342 176 0 0
in 207.95 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
221 208 13
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad74059010g200370m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 208 in ad74059010g200370m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.unf
Total Good Bad: Region Time Phase Cut
3261 1243 1316 702 0 0
Writing events file
1243 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3261 1243 1316 702 0 0
in 1477.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
1243 1175 68
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad74059010g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 1175 in ad74059010g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2714 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.unf
Total Good Bad: Region Time Phase Cut
2714 651 1017 1046 0 0
Writing events file
651 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2714 651 1017 1046 0 0
in 991.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
651 620 31
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad74059010g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 620 in ad74059010g300270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.unf
Total Good Bad: Region Time Phase Cut
725 216 322 187 0 0
Writing events file
216 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
725 216 322 187 0 0
in 207.95 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
216 204 12
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!screen:ASCA > read events ad74059010g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad74059010g300370m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 204 in ad74059010g300370m.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad74059010g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3439
Mean RA/DEC/ROLL : 338.8825 -26.1267 115.3439
Pnt RA/DEC/ROLL : 339.0333 -26.1173 115.3439
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 3
Total GTI (secs) : 1477.976
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 496.9786682 496.9786682
20 Percent Complete: Total/live time: 496.9786682 496.9786682
30 Percent Complete: Total/live time: 506.9786682 506.9786682
40 Percent Complete: Total/live time: 1028.4770508 1028.4770508
50 Percent Complete: Total/live time: 1028.4770508 1028.4770508
60 Percent Complete: Total/live time: 1477.9758301 1477.9758301
100 Percent Complete: Total/live time: 1477.9758301 1477.9758301
Number of attitude steps used: 5
Number of attitude steps avail: 2947
Mean RA/DEC pixel offset: -7.6809 -4.0265
writing expo file: ad74059010g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 1049 9 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1058 1049 9 0 0 0
in 1477.98 seconds
Image has 1049 counts for 0.7098 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 430 9 0 0 619
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1058 430 9 0 0 619
in 1477.98 seconds
Image has 430 counts for 0.2909 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 622 9 0 0 427
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1058 622 9 0 0 427
in 1477.98 seconds
Image has 622 counts for 0.4208 counts/sec
Command not found; type ? for a command listing
!ad74059010g200170h:ASCA >
!ad74059010g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g200170h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g200170h:ASCA > read events ad74059010g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g200170h:ASCA-GIS2-PH > set image sky
!ad74059010g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad74059010g200170h:ASCA-GIS2-PH > extract image
!ad74059010g200170h:ASCA-GIS2-PH > save image outfile=ad74059010g200170h.img
Wrote image to file ad74059010g200170h.img
!ad74059010g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad74059010g200170h:ASCA-GIS2-PH > extract image
!ad74059010g200170h:ASCA-GIS2-PH > save image outfile=ad74059010g200170h_lo.img
Wrote image to file ad74059010g200170h_lo.img
!ad74059010g200170h:ASCA-GIS2-PH > clear pha_cut
!ad74059010g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g200170h:ASCA-GIS2-PH > extract image
!ad74059010g200170h:ASCA-GIS2-PH > save image outfile=ad74059010g200170h_hi.img
Wrote image to file ad74059010g200170h_hi.img
!ad74059010g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad74059010g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad74059010g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3581
Mean RA/DEC/ROLL : 338.8474 -26.1385 115.3581
Pnt RA/DEC/ROLL : 339.0331 -26.1174 115.3581
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 1
Total GTI (secs) : 991.988
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 132.9902344 132.9902344
20 Percent Complete: Total/live time: 245.9899445 245.9899445
30 Percent Complete: Total/live time: 433.4894409 433.4894409
40 Percent Complete: Total/live time: 433.4894409 433.4894409
50 Percent Complete: Total/live time: 663.4887695 663.4887695
60 Percent Complete: Total/live time: 663.4887695 663.4887695
70 Percent Complete: Total/live time: 934.9879150 934.9879150
80 Percent Complete: Total/live time: 934.9879150 934.9879150
90 Percent Complete: Total/live time: 991.9877319 991.9877319
100 Percent Complete: Total/live time: 991.9877319 991.9877319
Number of attitude steps used: 8
Number of attitude steps avail: 2149
Mean RA/DEC pixel offset: -9.0803 -1.1789
writing expo file: ad74059010g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 488 5 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
493 488 5 0 0 0
in 991.99 seconds
Image has 488 counts for 0.4919 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 192 5 0 0 296
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
493 192 5 0 0 296
in 991.99 seconds
Image has 192 counts for 0.1936 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 299 5 0 0 189
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
493 299 5 0 0 189
in 991.99 seconds
Image has 299 counts for 0.3014 counts/sec
Command not found; type ? for a command listing
!ad74059010g200270h:ASCA >
!ad74059010g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g200270h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g200270h:ASCA > read events ad74059010g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g200270h:ASCA-GIS2-PH > set image sky
!ad74059010g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad74059010g200270h:ASCA-GIS2-PH > extract image
!ad74059010g200270h:ASCA-GIS2-PH > save image outfile=ad74059010g200270h.img
Wrote image to file ad74059010g200270h.img
!ad74059010g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad74059010g200270h:ASCA-GIS2-PH > extract image
!ad74059010g200270h:ASCA-GIS2-PH > save image outfile=ad74059010g200270h_lo.img
Wrote image to file ad74059010g200270h_lo.img
!ad74059010g200270h:ASCA-GIS2-PH > clear pha_cut
!ad74059010g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g200270h:ASCA-GIS2-PH > extract image
!ad74059010g200270h:ASCA-GIS2-PH > save image outfile=ad74059010g200270h_hi.img
Wrote image to file ad74059010g200270h_hi.img
!ad74059010g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad74059010g200370m.expo
ASCAEXPO_V0.9b
reading data file: ad74059010g200370m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3072
Mean RA/DEC/ROLL : 338.9064 -26.1164 115.3072
Pnt RA/DEC/ROLL : 338.9123 -26.1614 115.3072
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 1
Total GTI (secs) : 207.945
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 207.9454498 207.9454498
100 Percent Complete: Total/live time: 207.9454498 207.9454498
Number of attitude steps used: 2
Number of attitude steps avail: 74
Mean RA/DEC pixel offset: -5.2019 -1.5491
writing expo file: ad74059010g200370m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g200370m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g200370m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 208 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 206 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
208 206 2 0 0 0
in 207.95 seconds
Image has 206 counts for 0.9906 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 69 2 0 0 137
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
208 69 2 0 0 137
in 207.95 seconds
Image has 69 counts for 0.3318 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 139 2 0 0 67
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
208 139 2 0 0 67
in 207.95 seconds
Image has 139 counts for 0.6684 counts/sec
Command not found; type ? for a command listing
!ad74059010g200370m:ASCA >
!ad74059010g200370m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g200370m:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g200370m:ASCA > read events ad74059010g200370m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g200370m:ASCA-GIS2-PH > set image sky
!ad74059010g200370m:ASCA-GIS2-PH > filter region corner_point.reg
!ad74059010g200370m:ASCA-GIS2-PH > extract image
!ad74059010g200370m:ASCA-GIS2-PH > save image outfile=ad74059010g200370m.img
Wrote image to file ad74059010g200370m.img
!ad74059010g200370m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad74059010g200370m:ASCA-GIS2-PH > extract image
!ad74059010g200370m:ASCA-GIS2-PH > save image outfile=ad74059010g200370m_lo.img
Wrote image to file ad74059010g200370m_lo.img
!ad74059010g200370m:ASCA-GIS2-PH > clear pha_cut
!ad74059010g200370m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g200370m:ASCA-GIS2-PH > extract image
!ad74059010g200370m:ASCA-GIS2-PH > save image outfile=ad74059010g200370m_hi.img
Wrote image to file ad74059010g200370m_hi.img
!ad74059010g200370m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad74059010g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad74059010g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3399
Mean RA/DEC/ROLL : 338.8929 -26.1497 115.3399
Pnt RA/DEC/ROLL : 339.0239 -26.0939 115.3399
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 3
Total GTI (secs) : 1477.976
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 496.9786682 496.9786682
20 Percent Complete: Total/live time: 496.9786682 496.9786682
30 Percent Complete: Total/live time: 506.9786682 506.9786682
40 Percent Complete: Total/live time: 1028.4770508 1028.4770508
50 Percent Complete: Total/live time: 1028.4770508 1028.4770508
60 Percent Complete: Total/live time: 1477.9758301 1477.9758301
100 Percent Complete: Total/live time: 1477.9758301 1477.9758301
Number of attitude steps used: 5
Number of attitude steps avail: 2947
Mean RA/DEC pixel offset: 1.9821 -3.0666
writing expo file: ad74059010g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 1169 6 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1175 1169 6 0 0 0
in 1477.98 seconds
Image has 1169 counts for 0.7909 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 455 6 0 0 714
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1175 455 6 0 0 714
in 1477.98 seconds
Image has 455 counts for 0.3079 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 716 6 0 0 453
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1175 716 6 0 0 453
in 1477.98 seconds
Image has 716 counts for 0.4844 counts/sec
Command not found; type ? for a command listing
!ad74059010g300170h:ASCA >
!ad74059010g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g300170h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g300170h:ASCA > read events ad74059010g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g300170h:ASCA-GIS3-PH > set image sky
!ad74059010g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad74059010g300170h:ASCA-GIS3-PH > extract image
!ad74059010g300170h:ASCA-GIS3-PH > save image outfile=ad74059010g300170h.img
Wrote image to file ad74059010g300170h.img
!ad74059010g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad74059010g300170h:ASCA-GIS3-PH > extract image
!ad74059010g300170h:ASCA-GIS3-PH > save image outfile=ad74059010g300170h_lo.img
Wrote image to file ad74059010g300170h_lo.img
!ad74059010g300170h:ASCA-GIS3-PH > clear pha_cut
!ad74059010g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g300170h:ASCA-GIS3-PH > extract image
!ad74059010g300170h:ASCA-GIS3-PH > save image outfile=ad74059010g300170h_hi.img
Wrote image to file ad74059010g300170h_hi.img
!ad74059010g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad74059010g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad74059010g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3540
Mean RA/DEC/ROLL : 338.8588 -26.1611 115.3540
Pnt RA/DEC/ROLL : 339.0238 -26.0941 115.3540
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 1
Total GTI (secs) : 991.988
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 132.9902344 132.9902344
20 Percent Complete: Total/live time: 245.9899445 245.9899445
30 Percent Complete: Total/live time: 433.4894409 433.4894409
40 Percent Complete: Total/live time: 433.4894409 433.4894409
50 Percent Complete: Total/live time: 663.4887695 663.4887695
60 Percent Complete: Total/live time: 663.4887695 663.4887695
70 Percent Complete: Total/live time: 934.9879150 934.9879150
80 Percent Complete: Total/live time: 934.9879150 934.9879150
90 Percent Complete: Total/live time: 991.9877319 991.9877319
100 Percent Complete: Total/live time: 991.9877319 991.9877319
Number of attitude steps used: 8
Number of attitude steps avail: 2149
Mean RA/DEC pixel offset: 1.4886 -0.1290
writing expo file: ad74059010g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 617 3 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
620 617 3 0 0 0
in 991.99 seconds
Image has 617 counts for 0.6220 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 232 3 0 0 385
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
620 232 3 0 0 385
in 991.99 seconds
Image has 232 counts for 0.2339 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 387 3 0 0 230
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
620 387 3 0 0 230
in 991.99 seconds
Image has 387 counts for 0.3901 counts/sec
Command not found; type ? for a command listing
!ad74059010g300270h:ASCA >
!ad74059010g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g300270h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g300270h:ASCA > read events ad74059010g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g300270h:ASCA-GIS3-PH > set image sky
!ad74059010g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad74059010g300270h:ASCA-GIS3-PH > extract image
!ad74059010g300270h:ASCA-GIS3-PH > save image outfile=ad74059010g300270h.img
Wrote image to file ad74059010g300270h.img
!ad74059010g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad74059010g300270h:ASCA-GIS3-PH > extract image
!ad74059010g300270h:ASCA-GIS3-PH > save image outfile=ad74059010g300270h_lo.img
Wrote image to file ad74059010g300270h_lo.img
!ad74059010g300270h:ASCA-GIS3-PH > clear pha_cut
!ad74059010g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g300270h:ASCA-GIS3-PH > extract image
!ad74059010g300270h:ASCA-GIS3-PH > save image outfile=ad74059010g300270h_hi.img
Wrote image to file ad74059010g300270h_hi.img
!ad74059010g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad74059010g300370m.expo
ASCAEXPO_V0.9b
reading data file: ad74059010g300370m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3032
Mean RA/DEC/ROLL : 338.9156 -26.1398 115.3032
Pnt RA/DEC/ROLL : 338.9030 -26.1380 115.3032
Image rebin factor : 1
Attitude Records : 13433
GTI intervals : 1
Total GTI (secs) : 207.945
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 207.9454498 207.9454498
100 Percent Complete: Total/live time: 207.9454498 207.9454498
Number of attitude steps used: 2
Number of attitude steps avail: 74
Mean RA/DEC pixel offset: 0.8374 -0.9491
writing expo file: ad74059010g300370m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010g300370m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010g300370m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 204 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 204 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
204 204 0 0 0 0
in 207.95 seconds
Image has 204 counts for 0.9810 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 77 0 0 0 127
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
204 77 0 0 0 127
in 207.95 seconds
Image has 77 counts for 0.3703 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 128 0 0 0 76
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
204 128 0 0 0 76
in 207.95 seconds
Image has 128 counts for 0.6155 counts/sec
Command not found; type ? for a command listing
!ad74059010g300370m:ASCA >
!ad74059010g300370m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010g300370m:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010g300370m:ASCA > read events ad74059010g300370m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010g300370m:ASCA-GIS3-PH > set image sky
!ad74059010g300370m:ASCA-GIS3-PH > filter region corner_point.reg
!ad74059010g300370m:ASCA-GIS3-PH > extract image
!ad74059010g300370m:ASCA-GIS3-PH > save image outfile=ad74059010g300370m.img
Wrote image to file ad74059010g300370m.img
!ad74059010g300370m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad74059010g300370m:ASCA-GIS3-PH > extract image
!ad74059010g300370m:ASCA-GIS3-PH > save image outfile=ad74059010g300370m_lo.img
Wrote image to file ad74059010g300370m_lo.img
!ad74059010g300370m:ASCA-GIS3-PH > clear pha_cut
!ad74059010g300370m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad74059010g300370m:ASCA-GIS3-PH > extract image
!ad74059010g300370m:ASCA-GIS3-PH > save image outfile=ad74059010g300370m_hi.img
Wrote image to file ad74059010g300370m_hi.img
!ad74059010g300370m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad74059010s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad74059010s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 58 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 82 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3351
Mean RA/DEC/ROLL : 338.8971 -26.1335 115.3351
Pnt RA/DEC/ROLL : 339.0131 -26.1121 115.3351
Image rebin factor : 4
Attitude Records : 13433
Hot Pixels : 6
GTI intervals : 5
Total GTI (secs) : 2203.838
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 245.9899445 245.9899445
20 Percent Complete: Total/live time: 663.4887695 663.4887695
30 Percent Complete: Total/live time: 934.9879150 934.9879150
40 Percent Complete: Total/live time: 934.9879150 934.9879150
50 Percent Complete: Total/live time: 1878.9016113 1878.9016113
60 Percent Complete: Total/live time: 1878.9016113 1878.9016113
70 Percent Complete: Total/live time: 2142.4008789 2142.4008789
80 Percent Complete: Total/live time: 2142.4008789 2142.4008789
90 Percent Complete: Total/live time: 2154.4008789 2154.4008789
100 Percent Complete: Total/live time: 2203.8381348 2203.8381348
Number of attitude steps used: 14
Number of attitude steps avail: 4616
Mean RA/DEC pixel offset: -33.3439 -85.6594
writing expo file: ad74059010s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 1146 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 1146 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 1146 0 0 0 0
in 2203.84 seconds
Image has 1146 counts for 0.5200 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 521 0 0 0 625
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 521 0 0 0 625
in 2203.84 seconds
Image has 521 counts for 0.2364 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 625 0 0 0 521
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 625 0 0 0 521
in 2203.84 seconds
Image has 625 counts for 0.2836 counts/sec
Command not found; type ? for a command listing
!ad74059010s000102h:ASCA >
!ad74059010s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010s000102h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010s000102h:ASCA > read events ad74059010s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad74059010s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad74059010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad74059010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad74059010s000102h.img
Wrote image to file ad74059010s000102h.img
!ad74059010s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad74059010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad74059010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad74059010s000102h_lo.img
Wrote image to file ad74059010s000102h_lo.img
!ad74059010s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad74059010s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad74059010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad74059010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad74059010s000102h_hi.img
Wrote image to file ad74059010s000102h_hi.img
!ad74059010s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad74059010s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad74059010s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 58
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 82
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa961113_0714.1230
making an exposure map...
Aspect RA/DEC/ROLL : 338.9100 -26.1384 115.3424
Mean RA/DEC/ROLL : 338.8736 -26.1419 115.3424
Pnt RA/DEC/ROLL : 339.0296 -26.1062 115.3424
Image rebin factor : 4
Attitude Records : 13433
Hot Pixels : 10
GTI intervals : 6
Total GTI (secs) : 2159.838
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 245.9899445 245.9899445
20 Percent Complete: Total/live time: 663.4887695 663.4887695
30 Percent Complete: Total/live time: 934.9879150 934.9879150
40 Percent Complete: Total/live time: 934.9879150 934.9879150
50 Percent Complete: Total/live time: 1842.9016113 1842.9016113
60 Percent Complete: Total/live time: 1842.9016113 1842.9016113
70 Percent Complete: Total/live time: 2106.4008789 2106.4008789
80 Percent Complete: Total/live time: 2106.4008789 2106.4008789
90 Percent Complete: Total/live time: 2118.4008789 2118.4008789
100 Percent Complete: Total/live time: 2159.8381348 2159.8381348
Number of attitude steps used: 14
Number of attitude steps avail: 4616
Mean RA/DEC pixel offset: -37.4707 -18.9406
writing expo file: ad74059010s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad74059010s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad74059010s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 972 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 972 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 972 0 0 0 0
in 2159.84 seconds
Image has 972 counts for 0.4500 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 455 0 0 0 517
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 455 0 0 0 517
in 2159.84 seconds
Image has 455 counts for 0.2107 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 517 0 0 0 455
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 517 0 0 0 455
in 2159.84 seconds
Image has 517 counts for 0.2394 counts/sec
Command not found; type ? for a command listing
!ad74059010s100102h:ASCA >
!ad74059010s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad74059010s100102h:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!ad74059010s100102h:ASCA > read events ad74059010s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!ad74059010s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad74059010s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad74059010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad74059010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad74059010s100102h.img
Wrote image to file ad74059010s100102h.img
!ad74059010s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad74059010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad74059010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad74059010s100102h_lo.img
Wrote image to file ad74059010s100102h_lo.img
!ad74059010s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad74059010s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad74059010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad74059010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad74059010s100102h_hi.img
Wrote image to file ad74059010s100102h_hi.img
!ad74059010s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad74059010s000102h.expo ad74059010s100102h.expo-> Summing the following images to produce ad74059010sis32002_all.totsky
ad74059010s000102h.img ad74059010s100102h.img-> Summing the following images to produce ad74059010sis32002_lo.totsky
ad74059010s000102h_lo.img ad74059010s100102h_lo.img-> Summing the following images to produce ad74059010sis32002_hi.totsky
ad74059010s000102h_hi.img ad74059010s100102h_hi.img-> Running XIMAGE to create ad74059010sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad74059010sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 15.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 15 min: 0 ![2]XIMAGE> read/exp_map ad74059010sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 72.7279 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 72 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 19 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 14.0000 14 0 ![9]XIMAGE> exit-> Summing gis images
ad74059010g200170h.expo ad74059010g200270h.expo ad74059010g200370m.expo ad74059010g300170h.expo ad74059010g300270h.expo ad74059010g300370m.expo-> Summing the following images to produce ad74059010gis25670_all.totsky
ad74059010g200170h.img ad74059010g200270h.img ad74059010g200370m.img ad74059010g300170h.img ad74059010g300270h.img ad74059010g300370m.img-> Summing the following images to produce ad74059010gis25670_lo.totsky
ad74059010g200170h_lo.img ad74059010g200270h_lo.img ad74059010g200370m_lo.img ad74059010g300170h_lo.img ad74059010g300270h_lo.img ad74059010g300370m_lo.img-> Summing the following images to produce ad74059010gis25670_hi.totsky
ad74059010g200170h_hi.img ad74059010g200270h_hi.img ad74059010g200370m_hi.img ad74059010g300170h_hi.img ad74059010g300270h_hi.img ad74059010g300370m_hi.img-> Running XIMAGE to create ad74059010gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad74059010gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 23.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 23 min: 0 ![2]XIMAGE> read/exp_map ad74059010gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 89.2636 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 89 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 27 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 18.0000 18 0 ![9]XIMAGE> exit
123 149 0.00251025 113 7 266.305-> Smoothing ad74059010gis25670_hi.totsky with ad74059010gis25670.totexpo
123 150 0.00182564 114 7 288.728-> Smoothing ad74059010gis25670_lo.totsky with ad74059010gis25670.totexpo
124 149 0.00118251 112 7 241.906-> Determining extraction radii
123 149 24 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad74059010gis25670.src
145 207 0.00173147 96 9 290.899-> Smoothing ad74059010sis32002_hi.totsky with ad74059010sis32002.totexpo
147 208 0.000669161 96 11 165.377-> Smoothing ad74059010sis32002_lo.totsky with ad74059010sis32002.totexpo
145 207 0.000669161 96 10 202.398-> Determining extraction radii
145 207 38 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad74059010sis32002.src
The sum of the selected column is 1439.0000 The mean of the selected column is 479.66667 The standard deviation of the selected column is 2.3094011 The minimum of selected column is 477.00000 The maximum of selected column is 481.00000 The number of points used in calculation is 3-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1381.0000 The mean of the selected column is 460.33333 The standard deviation of the selected column is 10.503968 The minimum of selected column is 450.00000 The maximum of selected column is 471.00000 The number of points used in calculation is 3-> Converting (580.0,828.0,2.0) to s1 detector coordinates
The sum of the selected column is 2395.0000 The mean of the selected column is 479.00000 The standard deviation of the selected column is 2.9154759 The minimum of selected column is 474.00000 The maximum of selected column is 481.00000 The number of points used in calculation is 5-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2440.0000 The mean of the selected column is 488.00000 The standard deviation of the selected column is 8.9721792 The minimum of selected column is 483.00000 The maximum of selected column is 504.00000 The number of points used in calculation is 5-> Converting (123.0,149.0,2.0) to g2 detector coordinates
The sum of the selected column is 9871.0000 The mean of the selected column is 108.47253 The standard deviation of the selected column is 1.1386216 The minimum of selected column is 106.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10289.000 The mean of the selected column is 113.06593 The standard deviation of the selected column is 1.4817572 The minimum of selected column is 111.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 91-> Converting (123.0,149.0,2.0) to g3 detector coordinates
The sum of the selected column is 10423.000 The mean of the selected column is 114.53846 The standard deviation of the selected column is 1.1861019 The minimum of selected column is 112.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 91-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 10312.000 The mean of the selected column is 113.31868 The standard deviation of the selected column is 1.4132635 The minimum of selected column is 111.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 91
1 ad74059010s000102h.evt 1146-> Fetching SIS0_NOTCHIP0.1
ad74059010s000102h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 1146 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
in 2203.84 seconds
Spectrum has 1017 counts for 0.4615 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2203.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad74059010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad74059010s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad74059010s010102_1.pi group=yes
Wrote spectrum to ad74059010s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad74059010s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2203.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 33 are grouped by a factor 18 ... 34 - 38 are grouped by a factor 5 ... 39 - 42 are grouped by a factor 4 ... 43 - 45 are grouped by a factor 3 ... 46 - 49 are grouped by a factor 4 ... 50 - 61 are grouped by a factor 3 ... 62 - 65 are grouped by a factor 4 ... 66 - 70 are grouped by a factor 5 ... 71 - 76 are grouped by a factor 6 ... 77 - 90 are grouped by a factor 7 ... 91 - 98 are grouped by a factor 8 ... 99 - 116 are grouped by a factor 9 ... 117 - 128 are grouped by a factor 12 ... 129 - 139 are grouped by a factor 11 ... 140 - 154 are grouped by a factor 15 ... 155 - 174 are grouped by a factor 20 ... 175 - 200 are grouped by a factor 26 ... 201 - 290 are grouped by a factor 90 ... 291 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad74059010s010102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 39 bins
expanded to 39 by 39 bins
First WMAP bin is at detector pixel 328 312
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 487.00 471.00 (detector coordinates)
Point source at 21.97 11.00 (WMAP bins wrt optical axis)
Point source at 5.21 26.61 (... in polar coordinates)
Total counts in region = 1.00600E+03
Weighted mean angle from optical axis = 5.403 arcmin
-> Standard Output From STOOL group_event_files:1 ad74059010s000112h.evt 1173-> SIS0_NOTCHIP0.1 already present in current directory
ad74059010s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.22E+04 1173 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000112h.evt
Total Good Bad: Region Time Phase Cut
1173 1038 135 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1173 1038 135 0 0 0
in 2203.84 seconds
Spectrum has 1038 counts for 0.4710 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2203.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010s010212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad74059010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad74059010s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad74059010s010212_1.pi group=yes
Wrote spectrum to ad74059010s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad74059010s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2203.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 67 are grouped by a factor 36 ... 68 - 77 are grouped by a factor 10 ... 78 - 84 are grouped by a factor 7 ... 85 - 90 are grouped by a factor 6 ... 91 - 98 are grouped by a factor 8 ... 99 - 108 are grouped by a factor 5 ... 109 - 126 are grouped by a factor 6 ... 127 - 135 are grouped by a factor 9 ... 136 - 143 are grouped by a factor 8 ... 144 - 154 are grouped by a factor 11 ... 155 - 168 are grouped by a factor 14 ... 169 - 180 are grouped by a factor 12 ... 181 - 196 are grouped by a factor 16 ... 197 - 232 are grouped by a factor 18 ... 233 - 255 are grouped by a factor 23 ... 256 - 276 are grouped by a factor 21 ... 277 - 305 are grouped by a factor 29 ... 306 - 346 are grouped by a factor 41 ... 347 - 392 are grouped by a factor 46 ... 393 - 497 are grouped by a factor 105 ... 498 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad74059010s010212_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 39 bins
expanded to 39 by 39 bins
First WMAP bin is at detector pixel 328 312
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 487.00 471.00 (detector coordinates)
Point source at 21.97 11.00 (WMAP bins wrt optical axis)
Point source at 5.21 26.61 (... in polar coordinates)
Total counts in region = 1.02600E+03
Weighted mean angle from optical axis = 5.387 arcmin
-> Standard Output From STOOL group_event_files:1 ad74059010s100102h.evt 972-> Fetching SIS1_NOTCHIP0.1
ad74059010s100102h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 972 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 867 105 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 867 105 0 0 0
in 2159.84 seconds
Spectrum has 867 counts for 0.4014 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2159.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.45898E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad74059010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad74059010s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad74059010s110102_1.pi group=yes
Wrote spectrum to ad74059010s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad74059010s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2159.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.45898E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 34 are grouped by a factor 19 ... 35 - 40 are grouped by a factor 6 ... 41 - 44 are grouped by a factor 4 ... 45 - 47 are grouped by a factor 3 ... 48 - 55 are grouped by a factor 4 ... 56 - 58 are grouped by a factor 3 ... 59 - 62 are grouped by a factor 4 ... 63 - 68 are grouped by a factor 6 ... 69 - 76 are grouped by a factor 4 ... 77 - 85 are grouped by a factor 9 ... 86 - 98 are grouped by a factor 13 ... 99 - 108 are grouped by a factor 10 ... 109 - 117 are grouped by a factor 9 ... 118 - 128 are grouped by a factor 11 ... 129 - 144 are grouped by a factor 16 ... 145 - 165 are grouped by a factor 21 ... 166 - 209 are grouped by a factor 44 ... 210 - 471 are grouped by a factor 262 ... 472 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad74059010s110102_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 37 bins
expanded to 40 by 37 bins
First WMAP bin is at detector pixel 328 336
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 51.381 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 491.00 487.00 (detector coordinates)
Point source at 15.91 35.85 (WMAP bins wrt optical axis)
Point source at 8.32 66.07 (... in polar coordinates)
Total counts in region = 8.59000E+02
Weighted mean angle from optical axis = 8.141 arcmin
-> Standard Output From STOOL group_event_files:1 ad74059010s100112h.evt 987-> SIS1_NOTCHIP0.1 already present in current directory
ad74059010s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.22E+04 987 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100112h.evt
Total Good Bad: Region Time Phase Cut
987 875 112 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
987 875 112 0 0 0
in 2159.84 seconds
Spectrum has 875 counts for 0.4051 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2159.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.45898E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010s110212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad74059010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad74059010s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad74059010s110212_1.pi group=yes
Wrote spectrum to ad74059010s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad74059010s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2159.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.45898E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 68 are grouped by a factor 36 ... 69 - 79 are grouped by a factor 11 ... 80 - 87 are grouped by a factor 8 ... 88 - 99 are grouped by a factor 6 ... 100 - 113 are grouped by a factor 7 ... 114 - 119 are grouped by a factor 6 ... 120 - 128 are grouped by a factor 9 ... 129 - 139 are grouped by a factor 11 ... 140 - 147 are grouped by a factor 8 ... 148 - 156 are grouped by a factor 9 ... 157 - 176 are grouped by a factor 20 ... 177 - 200 are grouped by a factor 24 ... 201 - 220 are grouped by a factor 20 ... 221 - 238 are grouped by a factor 18 ... 239 - 262 are grouped by a factor 24 ... 263 - 291 are grouped by a factor 29 ... 292 - 340 are grouped by a factor 49 ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad74059010s110212_1.arf with point=yes
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 37 bins
expanded to 40 by 37 bins
First WMAP bin is at detector pixel 328 336
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 51.381 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 491.00 487.00 (detector coordinates)
Point source at 15.91 35.85 (WMAP bins wrt optical axis)
Point source at 8.32 66.07 (... in polar coordinates)
Total counts in region = 8.68000E+02
Weighted mean angle from optical axis = 8.138 arcmin
-> Standard Output From STOOL group_event_files:1 ad74059010g200170h.evt 1759 1 ad74059010g200270h.evt 1759 1 ad74059010g200370m.evt 1759-> GIS2_REGION256.4 already present in current directory
ad74059010g200170h.evt ad74059010g200270h.evt ad74059010g200370m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 208 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 583 475 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 234 259 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 127 81 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1759 944 815 0 0 0
in 2677.91 seconds
Spectrum has 944 counts for 0.3525 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2677.9 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad74059010g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad74059010g210170_1.pi group=yes
Wrote spectrum to ad74059010g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad74059010g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad74059010g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2677.9 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 82 are grouped by a factor 83 ... 83 - 100 are grouped by a factor 18 ... 101 - 110 are grouped by a factor 10 ... 111 - 134 are grouped by a factor 12 ... 135 - 144 are grouped by a factor 10 ... 145 - 151 are grouped by a factor 7 ... 152 - 162 are grouped by a factor 11 ... 163 - 170 are grouped by a factor 8 ... 171 - 180 are grouped by a factor 10 ... 181 - 194 are grouped by a factor 14 ... 195 - 215 are grouped by a factor 21 ... 216 - 232 are grouped by a factor 17 ... 233 - 255 are grouped by a factor 23 ... 256 - 276 are grouped by a factor 21 ... 277 - 303 are grouped by a factor 27 ... 304 - 331 are grouped by a factor 28 ... 332 - 360 are grouped by a factor 29 ... 361 - 397 are grouped by a factor 37 ... 398 - 451 are grouped by a factor 54 ... 452 - 511 are grouped by a factor 60 ... 512 - 608 are grouped by a factor 97 ... 609 - 960 are grouped by a factor 352 ... 961 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 46 51
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 108.00 113.00 (detector coordinates)
Point source at 25.00 17.96 (WMAP bins wrt optical axis)
Point source at 7.56 35.69 (... in polar coordinates)
Total counts in region = 9.44000E+02
Weighted mean angle from optical axis = 7.662 arcmin
-> Standard Output From STOOL group_event_files:1 ad74059010g300170h.evt 1999 1 ad74059010g300270h.evt 1999 1 ad74059010g300370m.evt 1999-> GIS3_REGION256.4 already present in current directory
ad74059010g300170h.evt ad74059010g300270h.evt ad74059010g300370m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 204 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 656 519 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 340 280 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 146 58 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1999 1142 857 0 0 0
in 2677.91 seconds
Spectrum has 1142 counts for 0.4265 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2677.9 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad74059010g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad74059010g310170_1.pi group=yes
Wrote spectrum to ad74059010g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad74059010g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad74059010g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2677.9 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 81 are grouped by a factor 82 ... 82 - 99 are grouped by a factor 18 ... 100 - 110 are grouped by a factor 11 ... 111 - 117 are grouped by a factor 7 ... 118 - 125 are grouped by a factor 8 ... 126 - 143 are grouped by a factor 9 ... 144 - 150 are grouped by a factor 7 ... 151 - 160 are grouped by a factor 10 ... 161 - 174 are grouped by a factor 7 ... 175 - 182 are grouped by a factor 8 ... 183 - 215 are grouped by a factor 11 ... 216 - 247 are grouped by a factor 16 ... 248 - 261 are grouped by a factor 14 ... 262 - 279 are grouped by a factor 18 ... 280 - 303 are grouped by a factor 24 ... 304 - 332 are grouped by a factor 29 ... 333 - 363 are grouped by a factor 31 ... 364 - 396 are grouped by a factor 33 ... 397 - 433 are grouped by a factor 37 ... 434 - 480 are grouped by a factor 47 ... 481 - 532 are grouped by a factor 52 ... 533 - 629 are grouped by a factor 97 ... 630 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad74059010g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 53 51
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Point source at 115.00 113.00 (detector coordinates)
Point source at 4.36 21.44 (WMAP bins wrt optical axis)
Point source at 5.37 78.51 (... in polar coordinates)
Total counts in region = 1.14200E+03
Weighted mean angle from optical axis = 5.614 arcmin
-> Plotting ad74059010g210170_1_pi.ps from ad74059010g210170_1.pi
XSPEC 9.01 07:40:49 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010g210170_1.pi
Net count rate (cts/s) for file 1 0.3525 +/- 1.1850E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad74059010g310170_1_pi.ps from ad74059010g310170_1.pi
XSPEC 9.01 07:41:19 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010g310170_1.pi
Net count rate (cts/s) for file 1 0.4265 +/- 1.4472E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad74059010s010102_1_pi.ps from ad74059010s010102_1.pi
XSPEC 9.01 07:41:51 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010s010102_1.pi
Net count rate (cts/s) for file 1 0.4615 +/- 1.5972E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad74059010s010212_1_pi.ps from ad74059010s010212_1.pi
XSPEC 9.01 07:42:21 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010s010212_1.pi
Net count rate (cts/s) for file 1 0.4710 +/- 1.7939E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad74059010s110102_1_pi.ps from ad74059010s110102_1.pi
XSPEC 9.01 07:42:59 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010s110102_1.pi
Net count rate (cts/s) for file 1 0.4014 +/- 1.4036E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad74059010s110212_1_pi.ps from ad74059010s110212_1.pi
XSPEC 9.01 07:43:33 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad74059010s110212_1.pi
Net count rate (cts/s) for file 1 0.4051 +/- 1.3936E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 1146 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
Writing events file
1017 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
in 2203.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT > filter region ad74059010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad74059010s000002_1.lc with binsize 108.349961506142
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 1017 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/events.tmp
Total Good Bad: Region Time Phase Cut
1017 1017 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1017 1017 0 0 0 0
in 2203.84 seconds
Fits light curve has 1017 counts for 0.4615 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT > set binsize 108.349961506142
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad74059010s000002_1.lc
Wrote FITS light curve to file ad74059010s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad74059010s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad74059010s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_7314_N2 Start Time (d) .... 10400 08:06:29.672
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10400 09:31:13.616
No. of Rows ....... 21 Bin Time (s) ...... 108.3
Right Ascension ... 3.3891E+02 Internal time sys.. Converted to TJD
Declination ....... -2.6138E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 47 Newbins of 108.350 (s)
Intv 1 Start10400 8: 7:23
Ser.1 Avg 0.4619 Chisq 84.06 Var 0.1834E-01 Newbs. 21
Min 0.2584 Max 0.7291 expVar 0.4581E-02 Bins 21
Results from Statistical Analysis
Newbin Integration Time (s).. 108.35
Interval Duration (s)........ 4984.1
No. of Newbins .............. 21
Average (c/s) ............... 0.46194 +/- 0.15E-01
Standard Deviation (c/s)..... 0.13542
Minimum (c/s)................ 0.25842
Maximum (c/s)................ 0.72912
Variance ((c/s)**2).......... 0.18339E-01 +/- 0.58E-02
Expected Variance ((c/s)**2). 0.45812E-02 +/- 0.14E-02
Third Moment ((c/s)**3)...... 0.29054E-03
Average Deviation (c/s)...... 0.11933
Skewness..................... 0.11699 +/- 0.53
Kurtosis..................... -1.0417 +/- 1.1
RMS fractional variation..... 0.25391 +/- 0.54E-01
Chi-Square................... 84.063 dof 20
Chi-Square Prob of constancy. 0.79393E-09 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.37447E-15 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 47 Newbins of 108.350 (s)
Intv 1 Start10400 8: 7:23
Ser.1 Avg 0.4619 Chisq 84.06 Var 0.1834E-01 Newbs. 21
Min 0.2584 Max 0.7291 expVar 0.4581E-02 Bins 21
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad74059010s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 972 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 868 104 0 0 0
Writing events file
868 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 868 104 0 0 0
in 2159.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT > filter region ad74059010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad74059010s100002_1.lc with binsize 124.414645205788
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 868 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/events.tmp
Total Good Bad: Region Time Phase Cut
868 868 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
868 868 0 0 0 0
in 2159.84 seconds
Fits light curve has 868 counts for 0.4019 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT > set binsize 124.414645205788
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad74059010s100002_1.lc
Wrote FITS light curve to file ad74059010s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad74059010s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad74059010s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_7314_N2 Start Time (d) .... 10400 08:06:29.672
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10400 09:31:09.616
No. of Rows ....... 19 Bin Time (s) ...... 124.4
Right Ascension ... 3.3891E+02 Internal time sys.. Converted to TJD
Declination ....... -2.6138E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 41 Newbins of 124.415 (s)
Intv 1 Start10400 8: 7:31
Ser.1 Avg 0.4116 Chisq 58.28 Var 0.1194E-01 Newbs. 19
Min 0.1929 Max 0.6500 expVar 0.3894E-02 Bins 19
Results from Statistical Analysis
Newbin Integration Time (s).. 124.41
Interval Duration (s)........ 4976.6
No. of Newbins .............. 19
Average (c/s) ............... 0.41155 +/- 0.15E-01
Standard Deviation (c/s)..... 0.10928
Minimum (c/s)................ 0.19290
Maximum (c/s)................ 0.64998
Variance ((c/s)**2).......... 0.11942E-01 +/- 0.40E-02
Expected Variance ((c/s)**2). 0.38936E-02 +/- 0.13E-02
Third Moment ((c/s)**3)...... 0.10447E-03
Average Deviation (c/s)...... 0.86766E-01
Skewness..................... 0.80054E-01 +/- 0.56
Kurtosis.....................-0.29932 +/- 1.1
RMS fractional variation..... 0.21799 +/- 0.54E-01
Chi-Square................... 58.276 dof 18
Chi-Square Prob of constancy. 0.38751E-05 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.90666E-11 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 41 Newbins of 124.415 (s)
Intv 1 Start10400 8: 7:31
Ser.1 Avg 0.4116 Chisq 58.28 Var 0.1194E-01 Newbs. 19
Min 0.1929 Max 0.6500 expVar 0.3894E-02 Bins 19
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad74059010g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 208 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 583 475 0 0 0
Writing events file
583 events written to the output file
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 234 259 0 0 0
Writing events file
817 events written to the output file
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 127 81 0 0 0
Writing events file
944 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1759 944 815 0 0 0
in 2677.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > filter region ad74059010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad74059010g200070_1.lc with binsize 141.838398207989
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.27E+04 944 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/events.tmp
Total Good Bad: Region Time Phase Cut
944 944 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
944 944 0 0 0 0
in 2677.91 seconds
Fits light curve has 944 counts for 0.3525 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > set binsize 141.838398207989
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad74059010g200070_1.lc
Wrote FITS light curve to file ad74059010g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad74059010g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad74059010g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_7314_N2 Start Time (d) .... 10400 08:06:29.672
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10400 12:20:05.617
No. of Rows ....... 18 Bin Time (s) ...... 141.8
Right Ascension ... 3.3891E+02 Internal time sys.. Converted to TJD
Declination ....... -2.6138E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 108 Newbins of 141.838 (s)
Intv 1 Start10400 8: 7:40
Ser.1 Avg 0.3467 Chisq 91.25 Var 0.1256E-01 Newbs. 18
Min 0.1763 Max 0.6345 expVar 0.2478E-02 Bins 18
Results from Statistical Analysis
Newbin Integration Time (s).. 141.84
Interval Duration (s)........ 15035.
No. of Newbins .............. 18
Average (c/s) ............... 0.34667 +/- 0.12E-01
Standard Deviation (c/s)..... 0.11208
Minimum (c/s)................ 0.17626
Maximum (c/s)................ 0.63452
Variance ((c/s)**2).......... 0.12563E-01 +/- 0.43E-02
Expected Variance ((c/s)**2). 0.24783E-02 +/- 0.85E-03
Third Moment ((c/s)**3)...... 0.95229E-03
Average Deviation (c/s)...... 0.88747E-01
Skewness..................... 0.67628 +/- 0.58
Kurtosis..................... 0.26565 +/- 1.2
RMS fractional variation..... 0.28968 +/- 0.62E-01
Chi-Square................... 91.247 dof 17
Chi-Square Prob of constancy. 0.36196E-11 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.16943E-12 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 108 Newbins of 141.838 (s)
Intv 1 Start10400 8: 7:40
Ser.1 Avg 0.3467 Chisq 91.25 Var 0.1256E-01 Newbs. 18
Min 0.1763 Max 0.6345 expVar 0.2478E-02 Bins 18
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad74059010g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 204 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 656 519 0 0 0
Writing events file
656 events written to the output file
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 340 280 0 0 0
Writing events file
996 events written to the output file
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 146 58 0 0 0
Writing events file
1142 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1999 1142 857 0 0 0
in 2677.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > filter region ad74059010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad74059010g300070_1.lc with binsize 117.246451758618
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.27E+04 1142 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/events.tmp
Total Good Bad: Region Time Phase Cut
1142 1142 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1142 1142 0 0 0 0
in 2677.91 seconds
Fits light curve has 1142 counts for 0.4265 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > set binsize 117.246451758618
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad74059010g300070_1.lc
Wrote FITS light curve to file ad74059010g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad74059010g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad74059010g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ NGC_7314_N2 Start Time (d) .... 10400 08:06:29.672
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10400 12:20:05.617
No. of Rows ....... 22 Bin Time (s) ...... 117.2
Right Ascension ... 3.3891E+02 Internal time sys.. Converted to TJD
Declination ....... -2.6138E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 130 Newbins of 117.246 (s)
Intv 1 Start10400 8: 7:28
Ser.1 Avg 0.4351 Chisq 89.10 Var 0.1564E-01 Newbs. 22
Min 0.1791 Max 0.8447 expVar 0.3862E-02 Bins 22
Results from Statistical Analysis
Newbin Integration Time (s).. 117.25
Interval Duration (s)........ 15125.
No. of Newbins .............. 22
Average (c/s) ............... 0.43507 +/- 0.14E-01
Standard Deviation (c/s)..... 0.12507
Minimum (c/s)................ 0.17911
Maximum (c/s)................ 0.84473
Variance ((c/s)**2).......... 0.15642E-01 +/- 0.48E-02
Expected Variance ((c/s)**2). 0.38623E-02 +/- 0.12E-02
Third Moment ((c/s)**3)...... 0.22823E-02
Average Deviation (c/s)...... 0.85391E-01
Skewness..................... 1.1666 +/- 0.52
Kurtosis..................... 3.3616 +/- 1.0
RMS fractional variation..... 0.24947 +/- 0.51E-01
Chi-Square................... 89.098 dof 21
Chi-Square Prob of constancy. 0.23084E-09 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.54860E-07 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 130 Newbins of 117.246 (s)
Intv 1 Start10400 8: 7:28
Ser.1 Avg 0.4351 Chisq 89.10 Var 0.1564E-01 Newbs. 22
Min 0.1791 Max 0.8447 expVar 0.3862E-02 Bins 22
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad74059010g200170h.evt[2] ad74059010g200270h.evt[2] ad74059010g200370m.evt[2]-> Making L1 light curve of ft961113_0714_1230G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5264 output records from 5268 good input G2_L1 records.-> Making L1 light curve of ft961113_0714_1230G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2445 output records from 5464 good input G2_L1 records.-> Merging GTIs from the following files:
ad74059010g300170h.evt[2] ad74059010g300270h.evt[2] ad74059010g300370m.evt[2]-> Making L1 light curve of ft961113_0714_1230G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5250 output records from 5254 good input G3_L1 records.-> Making L1 light curve of ft961113_0714_1230G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 2428 output records from 5441 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1058 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.evt
Total Good Bad: Region Time Phase Cut
1058 583 475 0 0 0
Writing events file
583 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1058 583 475 0 0 0
in 1477.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > filter region ad74059010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad74059010g200170h_1.ulc use_events=yes
Wrote events list to file ad74059010g200170h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 493 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.evt
Total Good Bad: Region Time Phase Cut
493 234 259 0 0 0
Writing events file
234 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
493 234 259 0 0 0
in 991.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > filter region ad74059010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad74059010g200270h_1.ulc use_events=yes
Wrote events list to file ad74059010g200270h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010g200370m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 208 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.evt
Total Good Bad: Region Time Phase Cut
208 127 81 0 0 0
Writing events file
127 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
208 127 81 0 0 0
in 207.95 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200370m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > filter region ad74059010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad74059010g200370m_1.ulc use_events=yes
Wrote events list to file ad74059010g200370m_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.15E+04 1175 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.evt
Total Good Bad: Region Time Phase Cut
1175 656 519 0 0 0
Writing events file
656 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1175 656 519 0 0 0
in 1477.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > filter region ad74059010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad74059010g300170h_1.ulc use_events=yes
Wrote events list to file ad74059010g300170h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.99E+03 620 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.evt
Total Good Bad: Region Time Phase Cut
620 340 280 0 0 0
Writing events file
340 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
620 340 280 0 0 0
in 991.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > filter region ad74059010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad74059010g300270h_1.ulc use_events=yes
Wrote events list to file ad74059010g300270h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010g300370m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.21E+03 204 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.evt
Total Good Bad: Region Time Phase Cut
204 146 58 0 0 0
Writing events file
146 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
204 146 58 0 0 0
in 207.95 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300370m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > filter region ad74059010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad74059010g300370m_1.ulc use_events=yes
Wrote events list to file ad74059010g300370m_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad74059010s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 1146 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.evt
Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
Writing events file
1017 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1146 1017 129 0 0 0
in 2203.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT > filter region ad74059010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad74059010s000102h_1.ulc use_events=yes
Wrote events list to file ad74059010s000102h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad74059010s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.22E+04 1173 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s000112h.evt
Total Good Bad: Region Time Phase Cut
1173 1038 135 0 0 0
Writing events file
1038 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1173 1038 135 0 0 0
in 2203.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad74059010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad74059010s000112h_1.ulc use_events=yes
Wrote events list to file ad74059010s000112h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad74059010s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.22E+04 972 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.evt
Total Good Bad: Region Time Phase Cut
972 868 104 0 0 0
Writing events file
868 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
972 868 104 0 0 0
in 2159.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT > filter region ad74059010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad74059010s100102h_1.ulc use_events=yes
Wrote events list to file ad74059010s100102h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad74059010s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.22E+04 987 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010s100112h.evt
Total Good Bad: Region Time Phase Cut
987 877 110 0 0 0
Writing events file
877 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
987 877 110 0 0 0
in 2159.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad74059010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad74059010s100112h_1.ulc use_events=yes
Wrote events list to file ad74059010s100112h_1.ulc
Changing Data directory from:
/data/data19/seq_proc/74059010.008/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 3338 Total of 0 sets of frame data are extracted.
1 ad74059010g200170h.unf 6633 1 ad74059010g200270h.unf 6633 1 ad74059010g200370m.unf 6633-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2583 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2583 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 739 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.unf
Total Good Bad: Region Time Phase Cut
3311 605 2706 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.unf
Total Good Bad: Region Time Phase Cut
2583 498 2085 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.unf
Total Good Bad: Region Time Phase Cut
739 129 610 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6633 1232 5401 0 0 0
in 6251.98 seconds
Spectrum has 1232 counts for 0.1971 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6252.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > read events ad74059010g200370m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad74059010g220170.cal group=yes
Wrote spectrum to ad74059010g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 08:14:00 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad74059010g220170.cal
Net count rate (cts/s) for file 1 0.1971 +/- 5.8002E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.2895E+05 using 84 PHA bins.
Reduced chi-squared = 2973.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.2653E+05 using 84 PHA bins.
Reduced chi-squared = 2904.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.2653E+05 using 84 PHA bins.
Reduced chi-squared = 2867.
!XSPEC> renorm
Chi-Squared = 410.5 using 84 PHA bins.
Reduced chi-squared = 5.196
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
347.57 0 1.000 5.892 6.1273E-02 5.4292E-02
4.6929E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
165.56 0 1.000 5.860 9.1662E-02 8.3352E-02
4.0451E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
104.09 -1 1.000 5.883 0.1437 0.1128
3.1372E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
76.588 -2 1.000 5.945 0.1789 0.1328
1.8178E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
74.728 -3 1.000 5.962 0.1879 0.1384
1.4114E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
74.727 -4 1.000 5.962 0.1878 0.1384
1.4138E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.96207 +/- 0.14489E-01
3 3 2 gaussian/b Sigma 0.187792 +/- 0.16227E-01
4 4 2 gaussian/b norm 0.138411 +/- 0.56035E-02
5 2 3 gaussian/b LineE 6.56427 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.197048 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.413770E-02 +/- 0.33378E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 74.73 using 84 PHA bins.
Reduced chi-squared = 0.9459
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad74059010g220170.cal peaks at 5.96207 +/- 0.014489 keV1 ad74059010g300170h.unf 6700 1 ad74059010g300270h.unf 6700 1 ad74059010g300370m.unf 6700-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2714 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
2 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2714 1024
3 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.unf
Total Good Bad: Region Time Phase Cut
3261 485 2776 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.unf
Total Good Bad: Region Time Phase Cut
2714 407 2307 0 0 0
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.unf
Total Good Bad: Region Time Phase Cut
725 123 602 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6700 1015 5685 0 0 0
in 6249.98 seconds
Spectrum has 1015 counts for 0.1624 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6250.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad74059010g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!xsel:ASCA > read events ad74059010g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > read events ad74059010g300370m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad74059010g320170.cal group=yes
Wrote spectrum to ad74059010g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 08:16:05 1-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad74059010g320170.cal
Net count rate (cts/s) for file 1 0.1624 +/- 5.3856E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 2.7694E+05 using 84 PHA bins.
Reduced chi-squared = 3597.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 2.7477E+05 using 84 PHA bins.
Reduced chi-squared = 3523.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 2.7477E+05 using 84 PHA bins.
Reduced chi-squared = 3478.
!XSPEC> renorm
Chi-Squared = 393.0 using 84 PHA bins.
Reduced chi-squared = 4.974
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
326.78 0 1.000 5.893 6.8734E-02 4.6865E-02
3.9201E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
121.57 0 1.000 5.863 0.1156 7.8814E-02
3.2926E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
48.515 -1 1.000 5.894 0.1351 0.1134
2.2022E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
44.661 -2 1.000 5.912 0.1432 0.1219
1.7272E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
44.608 -3 1.000 5.910 0.1397 0.1216
1.7614E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
44.607 -4 1.000 5.910 0.1399 0.1216
1.7565E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.91021 +/- 0.13328E-01
3 3 2 gaussian/b Sigma 0.139920 +/- 0.17730E-01
4 4 2 gaussian/b norm 0.121620 +/- 0.51593E-02
5 2 3 gaussian/b LineE 6.50717 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.146816 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.756481E-02 +/- 0.30362E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 44.61 using 84 PHA bins.
Reduced chi-squared = 0.5646
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad74059010g320170.cal peaks at 5.91021 +/- 0.013328 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.56E+04 4097 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad74059010s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.56E+04 4167 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad74059010s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT HIGH 13/11/96 07:24:59 0.56E+04 7840 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad74059010s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 NGC_7314 BRIGHT2 HIGH 13/11/96 07:24:59 0.56E+04 7880 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad74059010s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad74059010g200170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3311 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200170h.unf
Total Good Bad: Region Time Phase Cut
3311 628 0 2683 0 0
Writing events file
628 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3311 628 0 2683 0 0
in 778.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad74059010g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2583 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad74059010g200270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2583 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad74059010g200270h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 739 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad74059010g200370m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 739 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g200370m.unf
Total Good Bad: Region Time Phase Cut
739 305 0 434 0 0
Writing events file
305 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
739 305 0 434 0 0
in 432.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad74059010g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad74059010g300170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:24:57 0.30E+04 3261 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300170h.unf
Total Good Bad: Region Time Phase Cut
3261 606 0 2655 0 0
Writing events file
606 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3261 606 0 2655 0 0
in 778.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad74059010g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2714 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad74059010g300270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH HIGH 13/11/96 07:40:29 0.25E+04 2714 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad74059010g300270h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad74059010g300370m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 NGC_7314 PH MEDIUM 13/11/96 08:51:33 0.74E+03 725 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data19/seq_proc/74059010.008/ad74059010g300370m.unf
Total Good Bad: Region Time Phase Cut
725 307 0 418 0 0
Writing events file
307 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
725 307 0 418 0 0
in 432.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data19/seq_proc/74059010.008/
Setting mkf directory to /data/data19/seq_proc/74059010.008/
!earthevents:ASCA > read events ad74059010g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data19/seq_proc/74059010.008/
HK Directory is: /data/data19/seq_proc/74059010.008/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad74059010g200170h.unf|CPU2|RUN|CPU2 run/stop ad74059010g200270h.unf|CPU2|STOP|CPU2 run/stop ad74059010g200170h.unf|CPU3|RUN|CPU3 run/stop ad74059010g200270h.unf|CPU3|STOP|CPU3 run/stop-> listing ad74059010g200170h.unf
ad74059010g300170h.unf|CPU2|RUN|CPU2 run/stop ad74059010g300270h.unf|CPU2|STOP|CPU2 run/stop ad74059010g300170h.unf|CPU3|RUN|CPU3 run/stop ad74059010g300270h.unf|CPU3|STOP|CPU3 run/stop-> listing ad74059010g300170h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files