The following information is also available:
Time column is TIME ORDERED-> Fetching fa931102_0609.1958.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 26374165.833600 26423920.669300
Data file start and stop ascatime : 26374165.833600 26423920.669300
Aspecting run start and stop ascatime : 26374165.833744 26423920.669203
Time interval averaged over (seconds) : 49754.835458
Total pointing and manuver time (sec) : 33808.453125 15946.482422
Mean boresight Euler angles : 112.227610 58.781735 349.956244
RA DEC SUN ANGLE
Mean solar position (deg) : 216.73 -14.54
Mean aberration (arcsec) : 7.54 -4.13
Mean sat X-axis (deg) : 93.361173 -57.361800 94.35
Mean sat Y-axis (deg) : 196.982642 -8.577492 20.23
Mean sat Z-axis (deg) : 112.227610 31.218264 109.71
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 112.544510 31.304413 259.787048 4.072049
Minimum 112.343109 31.198334 259.173309 0.103469
Maximum 112.646179 31.359447 259.897339 12.285297
Sigma (RMS) 0.009406 0.006101 0.077813 2.533081
Number of ASPECT records processed = 39528
Aspecting to RA/DEC : 112.54450989 31.30441284
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 26386829.790039 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 26389677.780426 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 26392621.770211 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 112.545 DEC: 31.304
START TIME: SC 26374165.8337 = UT 02/11/93 06:09:25
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000123 5.467 4603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0
1371.995361 5.527 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1663.994385 4.503 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1731.994385 3.470 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1883.993774 2.430 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1947.993652 1.242 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
1975.993408 0.191 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2003.993408 1.231 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2023.993286 2.344 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2039.993286 3.426 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2059.993164 4.432 D848C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 1 0 3
2075.993164 5.451 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2099.993164 6.609 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2127.992920 7.952 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2159.992920 9.011 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2191.992920 10.066 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2231.992676 11.105 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2291.992432 12.108 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2645.991211 11.095 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2700.490967 9.956 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2828.490723 8.858 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
2960.489990 7.855 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
3212.489258 6.806 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
3436.488525 5.667 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
3565.988037 4.912 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
3724.487305 3.908 4403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0
6295.978516 2.896 4603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0
7195.975586 2.687 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
7407.974609 1.546 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
7759.973633 0.520 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8143.972168 1.608 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8335.971680 2.780 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8492.470703 3.872 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8652.470703 5.029 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8863.969727 6.033 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8915.969727 7.034 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8994.468750 8.035 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
9321.967773 7.896 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
15328.947266 6.670 4603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0
21548.925781 4.460 4603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0
24395.916016 3.824 F048C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 1 0 6
24955.914062 4.858 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
25319.914062 3.837 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
25725.412109 4.841 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
25867.412109 3.835 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
25938.412109 2.833 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
26124.410156 1.790 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
26278.410156 0.790 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
26589.910156 0.117 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
30155.898438 0.332 D048C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 1 0 2
30619.896484 1.352 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
31550.392578 2.352 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
32140.390625 3.359 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
32345.890625 3.660 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
35899.878906 3.354 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
37153.875000 4.358 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
38101.871094 5.115 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
41659.859375 4.715 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
43465.855469 3.711 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
43541.355469 2.709 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
43710.855469 1.708 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
43857.855469 1.423 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
47419.843750 1.028 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
48303.839844 2.180 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
48495.839844 3.225 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
48687.839844 4.395 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
48844.339844 5.453 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
49004.339844 6.600 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
49132.835938 7.600 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
49260.335938 8.671 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
49516.335938 9.873 4803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
49613.835938 10.799 4003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
49740.335938 12.119 4403 1 1 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0
49753.835938 12.118 5403 1 1 0 0 0 0 0 0 0 0 1 0 1 0 1 0 0
49754.835938 12.118 5403 1 1 0 0 0 0 0 0 0 0 1 0 1 0 1 0 0
Attitude Records: 39528
Attitude Steps: 75
Maneuver ACM time: 15946.5 sec
Pointed ACM time: 33808.5 sec
-> Calculating aspect point70 107 count=93 sum1=10418.8 sum2=5476.39 sum3=32554.3 71 106 count=100 sum1=11204.1 sum2=5887.91 sum3=35003.9 71 107 count=28 sum1=3137.04 sum2=1648.7 sum3=9801.14 72 106 count=128 sum1=14342.4 sum2=7535.81 sum3=44804.3 73 105 count=128 sum1=14343.6 sum2=7535.04 sum3=44803.5 74 104 count=64 sum1=7172.56 sum2=3767.04 sum3=22401.2 74 105 count=64 sum1=7172.25 sum2=3767.23 sum3=22401.4 75 103 count=35 sum1=3922.98 sum2=2059.79 sum3=12250.4 75 104 count=196 sum1=21967.3 sum2=11535.8 sum3=68603.1 76 103 count=157 sum1=17598.3 sum2=9239.1 sum3=54951.3 77 102 count=64 sum1=7174.53 sum2=3765.82 sum3=22400.1 77 103 count=64 sum1=7174.27 sum2=3765.95 sum3=22400.2 77 104 count=43 sum1=4820.41 sum2=2531.02 sum3=15052.4 77 105 count=613 sum1=68718.4 sum2=36082.9 sum3=214585 78 102 count=192 sum1=21525.1 sum2=11296.4 sum3=67199.2 78 104 count=3756 sum1=421102 sum2=221073 sum3=1.3148e+06 78 105 count=76 sum1=8520.09 sum2=4473.52 sum3=26604.2 79 101 count=192 sum1=21527.3 sum2=11295.1 sum3=67197.9 79 103 count=129 sum1=14463.7 sum2=7591.55 sum3=45155.1 79 104 count=521 sum1=58412.8 sum2=30665.8 sum3=182376 80 101 count=128 sum1=14352.7 sum2=7529.37 sum3=44798 80 102 count=16 sum1=1794.14 sum2=941.449 sum3=5600.46 80 103 count=49 sum1=5494.34 sum2=2883.41 sum3=17151.6 81 100 count=87 sum1=9756.17 sum2=5117.26 sum3=30449.5 81 101 count=87 sum1=9756.61 sum2=5117.55 sum3=30450 81 102 count=228 sum1=25568.7 sum2=13414.4 sum3=79809.3 82 99 count=8 sum1=897.224 sum2=470.479 sum3=2799.76 82 100 count=760 sum1=85235.1 sum2=44701.2 sum3=266001 82 101 count=161 sum1=18056.1 sum2=9471.37 sum3=56355.3 82 102 count=116 sum1=13008.9 sum2=6824.73 sum3=40604.3 83 99 count=61 sum1=6841.81 sum2=3587.32 sum3=21349.2 83 100 count=199 sum1=22320 sum2=11704.5 sum3=69652.9 83 101 count=2060 sum1=231046 sum2=121181 sum3=721056 84 98 count=24 sum1=2692.13 sum2=1411.16 sum3=8399.02 84 99 count=94 sum1=10544 sum2=5528.02 sum3=32899.6 84 100 count=282 sum1=31631.7 sum2=16586.6 sum3=98706.8 84 101 count=3 sum1=336.498 sum2=176.466 sum3=1050.07 85 97 count=1 sum1=112.183 sum2=58.791 sum3=349.952 85 98 count=23 sum1=2580.14 sum2=1352.25 sum3=8048.94 85 99 count=100 sum1=11218.1 sum2=5880.52 sum3=34999.8 85 100 count=8 sum1=897.408 sum2=470.496 sum3=2800.17 86 97 count=32 sum1=3590.09 sum2=1881.2 sum3=11198.3 86 98 count=286 sum1=32086.8 sum2=16816.7 sum3=100097 86 99 count=33 sum1=3702.17 sum2=1940.5 sum3=11550 86 102 count=1 sum1=112.195 sum2=58.837 sum3=349.492 87 96 count=24 sum1=2692.86 sum2=1410.74 sum3=8398.59 87 97 count=14 sum1=1570.81 sum2=823.012 sum3=4899.52 87 98 count=194 sum1=21766.8 sum2=11406.2 sum3=67897.5 87 99 count=11 sum1=1234.22 sum2=646.877 sum3=3845.82 87 100 count=10 sum1=1122 sum2=588.165 sum3=3495.67 87 101 count=9 sum1=1009.79 sum2=529.439 sum3=3145.68 87 102 count=6 sum1=673.195 sum2=353.016 sum3=2096.92 88 96 count=57 sum1=6396.07 sum2=3350.21 sum3=19946.3 88 97 count=221 sum1=24798.7 sum2=12992.2 sum3=77346.4 88 98 count=28 sum1=3141.8 sum2=1646.2 sum3=9797.89 88 102 count=4 sum1=448.84 sum2=235.348 sum3=1397.84 89 95 count=24 sum1=2693.35 sum2=1410.48 sum3=8398.33 89 96 count=1924 sum1=215919 sum2=113093 sum3=673356 89 97 count=231 sum1=25922.6 sum2=13579.2 sum3=80844.5 89 98 count=1 sum1=112.216 sum2=58.792 sum3=349.654 89 102 count=4 sum1=448.881 sum2=235.346 sum3=1397.77 90 95 count=602 sum1=67564.4 sum2=35377.1 sum3=210663 90 96 count=1062 sum1=119185 sum2=62423.2 sum3=371673 90 97 count=1 sum1=112.227 sum2=58.784 sum3=349.658 90 102 count=3 sum1=336.69 sum2=176.508 sum3=1048.29 91 94 count=629 sum1=70599.8 sum2=36958.4 sum3=220124 91 95 count=4742 sum1=532239 sum2=278663 sum3=1.65934e+06 91 96 count=26 sum1=2918.24 sum2=1528.11 sum3=9098.5 91 102 count=4 sum1=448.962 sum2=235.341 sum3=1397.65 92 94 count=519 sum1=58257.7 sum2=30495.2 sum3=181619 92 95 count=228 sum1=25592.3 sum2=13397.9 sum3=79780.9 92 96 count=24 sum1=2694 sum2=1410.64 sum3=8398.96 92 102 count=3 sum1=336.754 sum2=176.502 sum3=1048.21 93 92 count=174 sum1=19534 sum2=10220.9 sum3=60885.8 93 93 count=284 sum1=31882.8 sum2=16685.2 sum3=99383.6 93 94 count=346 sum1=38841.9 sum2=20328.9 sum3=121076 93 96 count=24 sum1=2694.27 sum2=1410.72 sum3=8398.68 93 102 count=3 sum1=336.785 sum2=176.496 sum3=1048.2 94 92 count=764 sum1=85775.8 sum2=44876.9 sum3=267339 94 93 count=927 sum1=104074 sum2=54459.4 sum3=324384 94 94 count=1 sum1=112.266 sum2=58.754 sum3=349.651 94 96 count=24 sum1=2694.48 sum2=1410.63 sum3=8398.52 94 102 count=6 sum1=673.624 sum2=353.001 sum3=2096.34 95 91 count=15 sum1=1684.18 sum2=880.965 sum3=5248.8 95 92 count=1860 sum1=208842 sum2=109255 sum3=650851 95 93 count=236 sum1=26497.4 sum2=13863.5 sum3=82580.8 95 94 count=464 sum1=52100.2 sum2=27265.1 sum3=162367 95 95 count=361 sum1=40534.2 sum2=21213.9 sum3=126325 95 96 count=8 sum1=898.208 sum2=470.184 sum3=2799.47 95 102 count=3 sum1=336.845 sum2=176.498 sum3=1048.15 96 91 count=468 sum1=52553.3 sum2=27484.4 sum3=163757 96 92 count=343 sum1=38515.6 sum2=20145.6 sum3=120015 96 93 count=64 sum1=7186.87 sum2=3760.06 sum3=22395.1 96 94 count=2819 sum1=316541 sum2=165635 sum3=986446 96 101 count=3 sum1=336.876 sum2=176.493 sum3=1048.11 96 102 count=1 sum1=112.288 sum2=58.832 sum3=349.377 97 91 count=5564 sum1=624847 sum2=326760 sum3=1.94688e+06 97 92 count=64 sum1=7186.96 sum2=3758.85 sum3=22393.6 97 93 count=192 sum1=21561.8 sum2=11279.3 sum3=67184.4 97 101 count=4 sum1=449.203 sum2=235.322 sum3=1397.43 98 91 count=3 sum1=336.93 sum2=176.172 sum3=1048.95 98 92 count=192 sum1=21563.5 sum2=11278.1 sum3=67183 98 101 count=4 sum1=449.238 sum2=235.313 sum3=1397.4 99 90 count=4 sum1=449.28 sum2=234.869 sum3=1398.61 99 91 count=64 sum1=7188.74 sum2=3758.72 sum3=22393.7 99 92 count=192 sum1=21565.2 sum2=11276.9 sum3=67181.8 99 100 count=2 sum1=224.65 sum2=117.642 sum3=698.707 99 101 count=81 sum1=9098.15 sum2=4764.73 sum3=28297.1 100 89 count=2 sum1=224.664 sum2=117.418 sum3=699.309 100 90 count=1 sum1=112.328 sum2=58.712 sum3=349.654 100 91 count=256 sum1=28756.6 sum2=15033.6 sum3=89573.3 100 100 count=152 sum1=17073.8 sum2=8940.06 sum3=53101.5 100 101 count=17 sum1=1909.55 sum2=999.978 sum3=5938.89 101 89 count=4 sum1=449.357 sum2=234.816 sum3=1398.63 101 90 count=512 sum1=57518.9 sum2=30062.4 sum3=179142 102 88 count=5 sum1=561.76 sum2=293.48 sum3=1748.32 102 89 count=122 sum1=13706.6 sum2=7162.48 sum3=42685.3 102 90 count=6 sum1=674.082 sum2=352.272 sum3=2099.29 103 87 count=2 sum1=224.725 sum2=117.379 sum3=699.352 103 88 count=80 sum1=8989.16 sum2=4696 sum3=27989.5 103 89 count=50 sum1=5617.95 sum2=2935.17 sum3=17493.8 104 87 count=31 sum1=3483.57 sum2=1819.38 sum3=10844.6 104 88 count=231 sum1=25957.4 sum2=13558.6 sum3=80819.2 105 86 count=4 sum1=449.527 sum2=234.709 sum3=1398.73 105 87 count=128 sum1=14384.6 sum2=7511.93 sum3=44781.3 106 85 count=4 sum1=449.566 sum2=234.682 sum3=1398.73 106 86 count=51 sum1=5731.91 sum2=2992.67 sum3=17841.7 106 87 count=16 sum1=1798.2 sum2=938.912 sum3=5597.53 107 85 count=24 sum1=2697.68 sum2=1408.08 sum3=8394.98 107 86 count=46 sum1=5170.34 sum2=2699.05 sum3=16092.5 108 84 count=32 sum1=3597.22 sum2=1877.1 sum3=11191.4 108 85 count=80 sum1=8992.81 sum2=4693.35 sum3=27985.3 109 84 count=12 sum1=1349 sum2=703.888 sum3=4196.82 0 out of 39527 points outside bin structure-> Euler angles: 112.3, 58.7279, 349.906
Interpolating 3 records in time interval 2.63926e+07 - 2.63957e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft931102_0609.1958",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft931102_0609.1958 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 553216 Bright = 79680 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 632896 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 10104 no. of SIS events found = 1238208-> Standard Error Output From FTOOL frfread
coordinate error 50 0 coordinate error 2 281 coordinate error 1 410 coordinate error 3 44 coordinate error 2 305 coordinate error 376 0-> Removing the following files with NEVENTS=0
ft931102_0609_1958G200899.fits ft931102_0609_1958G202670H.fits ft931102_0609_1958G203170M.fits ft931102_0609_1958G204170M.fits ft931102_0609_1958G205170M.fits ft931102_0609_1958G205599.fits ft931102_0609_1958G205770H.fits ft931102_0609_1958G205870H.fits ft931102_0609_1958G205970M.fits ft931102_0609_1958G206070M.fits ft931102_0609_1958G206399.fits ft931102_0609_1958G206670H.fits ft931102_0609_1958G206899.fits ft931102_0609_1958G300899.fits ft931102_0609_1958G302270H.fits ft931102_0609_1958G303170H.fits ft931102_0609_1958G303270H.fits ft931102_0609_1958G303870M.fits ft931102_0609_1958G304370H.fits ft931102_0609_1958G304870M.fits ft931102_0609_1958G305870M.fits ft931102_0609_1958G306299.fits ft931102_0609_1958G306470H.fits ft931102_0609_1958G306570H.fits ft931102_0609_1958G306670M.fits ft931102_0609_1958G306770M.fits ft931102_0609_1958G307099.fits ft931102_0609_1958G307370H.fits ft931102_0609_1958G307599.fits ft931102_0609_1958S000501M.fits ft931102_0609_1958S000602M.fits ft931102_0609_1958S000899.fits ft931102_0609_1958S001201M.fits ft931102_0609_1958S001501M.fits ft931102_0609_1958S001702M.fits ft931102_0609_1958S002301M.fits ft931102_0609_1958S002402M.fits ft931102_0609_1958S002502M.fits ft931102_0609_1958S002602M.fits ft931102_0609_1958S003101M.fits ft931102_0609_1958S003302M.fits ft931102_0609_1958S003701M.fits ft931102_0609_1958S004002M.fits ft931102_0609_1958S004102M.fits ft931102_0609_1958S004501M.fits ft931102_0609_1958S004602M.fits ft931102_0609_1958S004702M.fits ft931102_0609_1958S004802M.fits ft931102_0609_1958S005199.fits ft931102_0609_1958S005401M.fits ft931102_0609_1958S005502M.fits ft931102_0609_1958S005702M.fits ft931102_0609_1958S006099.fits ft931102_0609_1958S006299.fits ft931102_0609_1958S100301M.fits ft931102_0609_1958S100599.fits ft931102_0609_1958S100801M.fits ft931102_0609_1958S101001M.fits ft931102_0609_1958S101801M.fits ft931102_0609_1958S102101M.fits ft931102_0609_1958S102302M.fits ft931102_0609_1958S102601M.fits ft931102_0609_1958S102802M.fits ft931102_0609_1958S103101M.fits ft931102_0609_1958S103302M.fits ft931102_0609_1958S103699.fits ft931102_0609_1958S103801M.fits ft931102_0609_1958S103902M.fits ft931102_0609_1958S104002M.fits ft931102_0609_1958S104399.fits ft931102_0609_1958S104599.fits-> Checking for empty GTI extensions
ft931102_0609_1958S000102M.fits[3] ft931102_0609_1958S000202M.fits[3] ft931102_0609_1958S000301H.fits[3] ft931102_0609_1958S000401H.fits[3] ft931102_0609_1958S000702M.fits[3] ft931102_0609_1958S000902M.fits[3] ft931102_0609_1958S001001H.fits[3] ft931102_0609_1958S001101H.fits[3] ft931102_0609_1958S001302M.fits[3] ft931102_0609_1958S001401H.fits[3] ft931102_0609_1958S001602M.fits[3] ft931102_0609_1958S001802M.fits[3] ft931102_0609_1958S001901H.fits[3] ft931102_0609_1958S002001H.fits[3] ft931102_0609_1958S002101H.fits[3] ft931102_0609_1958S002201H.fits[3] ft931102_0609_1958S002702M.fits[3] ft931102_0609_1958S002802M.fits[3] ft931102_0609_1958S002901H.fits[3] ft931102_0609_1958S003001H.fits[3] ft931102_0609_1958S003202M.fits[3] ft931102_0609_1958S003402M.fits[3] ft931102_0609_1958S003502M.fits[3] ft931102_0609_1958S003601H.fits[3] ft931102_0609_1958S003802M.fits[3] ft931102_0609_1958S003902M.fits[3] ft931102_0609_1958S004202M.fits[3] ft931102_0609_1958S004301H.fits[3] ft931102_0609_1958S004401H.fits[3] ft931102_0609_1958S004902M.fits[3] ft931102_0609_1958S005001H.fits[3] ft931102_0609_1958S005201H.fits[3] ft931102_0609_1958S005301H.fits[3] ft931102_0609_1958S005602M.fits[3] ft931102_0609_1958S005802M.fits[3] ft931102_0609_1958S005901M.fits[3] ft931102_0609_1958S006101H.fits[3]-> Merging GTIs from the following files:
ft931102_0609_1958S100102M.fits[3] ft931102_0609_1958S100201H.fits[3] ft931102_0609_1958S100402M.fits[3] ft931102_0609_1958S100602M.fits[3] ft931102_0609_1958S100701H.fits[3] ft931102_0609_1958S100902M.fits[3] ft931102_0609_1958S101102M.fits[3] ft931102_0609_1958S101202M.fits[3] ft931102_0609_1958S101301H.fits[3] ft931102_0609_1958S101401H.fits[3] ft931102_0609_1958S101501H.fits[3] ft931102_0609_1958S101601H.fits[3] ft931102_0609_1958S101701H.fits[3] ft931102_0609_1958S101902M.fits[3] ft931102_0609_1958S102001H.fits[3] ft931102_0609_1958S102202M.fits[3] ft931102_0609_1958S102402M.fits[3] ft931102_0609_1958S102501H.fits[3] ft931102_0609_1958S102702M.fits[3] ft931102_0609_1958S102902M.fits[3] ft931102_0609_1958S103001H.fits[3] ft931102_0609_1958S103202M.fits[3] ft931102_0609_1958S103402M.fits[3] ft931102_0609_1958S103501H.fits[3] ft931102_0609_1958S103701H.fits[3] ft931102_0609_1958S104102M.fits[3] ft931102_0609_1958S104201M.fits[3] ft931102_0609_1958S104401H.fits[3]-> Merging GTIs from the following files:
ft931102_0609_1958G200170M.fits[3] ft931102_0609_1958G200270H.fits[3] ft931102_0609_1958G200370H.fits[3] ft931102_0609_1958G200470H.fits[3] ft931102_0609_1958G200570H.fits[3] ft931102_0609_1958G200670M.fits[3] ft931102_0609_1958G200770M.fits[3] ft931102_0609_1958G200970M.fits[3] ft931102_0609_1958G201070H.fits[3] ft931102_0609_1958G201170H.fits[3] ft931102_0609_1958G201270H.fits[3] ft931102_0609_1958G201370H.fits[3] ft931102_0609_1958G201470M.fits[3] ft931102_0609_1958G201570M.fits[3] ft931102_0609_1958G201670H.fits[3] ft931102_0609_1958G201770M.fits[3] ft931102_0609_1958G201870M.fits[3] ft931102_0609_1958G201970H.fits[3] ft931102_0609_1958G202070H.fits[3] ft931102_0609_1958G202170H.fits[3] ft931102_0609_1958G202270M.fits[3] ft931102_0609_1958G202370M.fits[3] ft931102_0609_1958G202470M.fits[3] ft931102_0609_1958G202570H.fits[3] ft931102_0609_1958G202770H.fits[3] ft931102_0609_1958G202870H.fits[3] ft931102_0609_1958G202970M.fits[3] ft931102_0609_1958G203070M.fits[3] ft931102_0609_1958G203270M.fits[3] ft931102_0609_1958G203370M.fits[3] ft931102_0609_1958G203470H.fits[3] ft931102_0609_1958G203570H.fits[3] ft931102_0609_1958G203670H.fits[3] ft931102_0609_1958G203770H.fits[3] ft931102_0609_1958G203870M.fits[3] ft931102_0609_1958G203970M.fits[3] ft931102_0609_1958G204070M.fits[3] ft931102_0609_1958G204270M.fits[3] ft931102_0609_1958G204370M.fits[3] ft931102_0609_1958G204470H.fits[3] ft931102_0609_1958G204570H.fits[3] ft931102_0609_1958G204670H.fits[3] ft931102_0609_1958G204770H.fits[3] ft931102_0609_1958G204870M.fits[3] ft931102_0609_1958G204970M.fits[3] ft931102_0609_1958G205070M.fits[3] ft931102_0609_1958G205270M.fits[3] ft931102_0609_1958G205370M.fits[3] ft931102_0609_1958G205470H.fits[3] ft931102_0609_1958G205670H.fits[3] ft931102_0609_1958G206170M.fits[3] ft931102_0609_1958G206270M.fits[3] ft931102_0609_1958G206470H.fits[3] ft931102_0609_1958G206570H.fits[3] ft931102_0609_1958G206770H.fits[3]-> Merging GTIs from the following files:
ft931102_0609_1958G300170M.fits[3] ft931102_0609_1958G300270H.fits[3] ft931102_0609_1958G300370H.fits[3] ft931102_0609_1958G300470H.fits[3] ft931102_0609_1958G300570H.fits[3] ft931102_0609_1958G300670M.fits[3] ft931102_0609_1958G300770M.fits[3] ft931102_0609_1958G300970M.fits[3] ft931102_0609_1958G301070H.fits[3] ft931102_0609_1958G301170H.fits[3] ft931102_0609_1958G301270H.fits[3] ft931102_0609_1958G301370H.fits[3] ft931102_0609_1958G301470M.fits[3] ft931102_0609_1958G301570M.fits[3] ft931102_0609_1958G301670H.fits[3] ft931102_0609_1958G301770M.fits[3] ft931102_0609_1958G301870M.fits[3] ft931102_0609_1958G301970M.fits[3] ft931102_0609_1958G302070M.fits[3] ft931102_0609_1958G302170H.fits[3] ft931102_0609_1958G302370H.fits[3] ft931102_0609_1958G302470H.fits[3] ft931102_0609_1958G302570H.fits[3] ft931102_0609_1958G302670H.fits[3] ft931102_0609_1958G302770M.fits[3] ft931102_0609_1958G302870M.fits[3] ft931102_0609_1958G302970M.fits[3] ft931102_0609_1958G303070H.fits[3] ft931102_0609_1958G303370H.fits[3] ft931102_0609_1958G303470H.fits[3] ft931102_0609_1958G303570H.fits[3] ft931102_0609_1958G303670M.fits[3] ft931102_0609_1958G303770M.fits[3] ft931102_0609_1958G303970M.fits[3] ft931102_0609_1958G304070M.fits[3] ft931102_0609_1958G304170H.fits[3] ft931102_0609_1958G304270H.fits[3] ft931102_0609_1958G304470H.fits[3] ft931102_0609_1958G304570M.fits[3] ft931102_0609_1958G304670M.fits[3] ft931102_0609_1958G304770M.fits[3] ft931102_0609_1958G304970M.fits[3] ft931102_0609_1958G305070M.fits[3] ft931102_0609_1958G305170H.fits[3] ft931102_0609_1958G305270H.fits[3] ft931102_0609_1958G305370H.fits[3] ft931102_0609_1958G305470H.fits[3] ft931102_0609_1958G305570M.fits[3] ft931102_0609_1958G305670M.fits[3] ft931102_0609_1958G305770M.fits[3] ft931102_0609_1958G305970M.fits[3] ft931102_0609_1958G306070M.fits[3] ft931102_0609_1958G306170H.fits[3] ft931102_0609_1958G306370H.fits[3] ft931102_0609_1958G306870M.fits[3] ft931102_0609_1958G306970M.fits[3] ft931102_0609_1958G307170H.fits[3] ft931102_0609_1958G307270H.fits[3] ft931102_0609_1958G307470H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 11 photon cnt = 15247 GISSORTSPLIT:LO:g200370h.prelist merge count = 5 photon cnt = 9 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 13 GISSORTSPLIT:LO:g200370m.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200470m.prelist merge count = 3 photon cnt = 15 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200670m.prelist merge count = 12 photon cnt = 12449 GISSORTSPLIT:LO:g200770m.prelist merge count = 7 photon cnt = 320 GISSORTSPLIT:LO:Total filenames split = 55 GISSORTSPLIT:LO:Total split file cnt = 21 GISSORTSPLIT:LO:End program-> Creating ad81009000g200170h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958G200570H.fits 2 -- ft931102_0609_1958G201370H.fits 3 -- ft931102_0609_1958G201670H.fits 4 -- ft931102_0609_1958G201970H.fits 5 -- ft931102_0609_1958G202170H.fits 6 -- ft931102_0609_1958G202870H.fits 7 -- ft931102_0609_1958G203770H.fits 8 -- ft931102_0609_1958G204770H.fits 9 -- ft931102_0609_1958G205470H.fits 10 -- ft931102_0609_1958G205670H.fits 11 -- ft931102_0609_1958G206770H.fits Merging binary extension #: 2 1 -- ft931102_0609_1958G200570H.fits 2 -- ft931102_0609_1958G201370H.fits 3 -- ft931102_0609_1958G201670H.fits 4 -- ft931102_0609_1958G201970H.fits 5 -- ft931102_0609_1958G202170H.fits 6 -- ft931102_0609_1958G202870H.fits 7 -- ft931102_0609_1958G203770H.fits 8 -- ft931102_0609_1958G204770H.fits 9 -- ft931102_0609_1958G205470H.fits 10 -- ft931102_0609_1958G205670H.fits 11 -- ft931102_0609_1958G206770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000g200270m.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958G200170M.fits 2 -- ft931102_0609_1958G200770M.fits 3 -- ft931102_0609_1958G200970M.fits 4 -- ft931102_0609_1958G201570M.fits 5 -- ft931102_0609_1958G201870M.fits 6 -- ft931102_0609_1958G202470M.fits 7 -- ft931102_0609_1958G203370M.fits 8 -- ft931102_0609_1958G203970M.fits 9 -- ft931102_0609_1958G204370M.fits 10 -- ft931102_0609_1958G204970M.fits 11 -- ft931102_0609_1958G205370M.fits 12 -- ft931102_0609_1958G206270M.fits Merging binary extension #: 2 1 -- ft931102_0609_1958G200170M.fits 2 -- ft931102_0609_1958G200770M.fits 3 -- ft931102_0609_1958G200970M.fits 4 -- ft931102_0609_1958G201570M.fits 5 -- ft931102_0609_1958G201870M.fits 6 -- ft931102_0609_1958G202470M.fits 7 -- ft931102_0609_1958G203370M.fits 8 -- ft931102_0609_1958G203970M.fits 9 -- ft931102_0609_1958G204370M.fits 10 -- ft931102_0609_1958G204970M.fits 11 -- ft931102_0609_1958G205370M.fits 12 -- ft931102_0609_1958G206270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000320 events
ft931102_0609_1958G200670M.fits ft931102_0609_1958G201470M.fits ft931102_0609_1958G201770M.fits ft931102_0609_1958G202270M.fits ft931102_0609_1958G202970M.fits ft931102_0609_1958G203870M.fits ft931102_0609_1958G204870M.fits-> Ignoring the following files containing 000000015 events
ft931102_0609_1958G203270M.fits ft931102_0609_1958G204270M.fits ft931102_0609_1958G205270M.fits-> Ignoring the following files containing 000000013 events
ft931102_0609_1958G204070M.fits ft931102_0609_1958G205070M.fits-> Ignoring the following files containing 000000009 events
ft931102_0609_1958G200470H.fits ft931102_0609_1958G201270H.fits ft931102_0609_1958G202770H.fits ft931102_0609_1958G203670H.fits ft931102_0609_1958G204670H.fits-> Ignoring the following files containing 000000007 events
ft931102_0609_1958G206170M.fits-> Ignoring the following files containing 000000007 events
ft931102_0609_1958G202370M.fits-> Ignoring the following files containing 000000005 events
ft931102_0609_1958G201070H.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G201170H.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G204470H.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G203470H.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G203070M.fits-> Ignoring the following files containing 000000002 events
ft931102_0609_1958G206570H.fits-> Ignoring the following files containing 000000002 events
ft931102_0609_1958G200370H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G206470H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G200270H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G204570H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G203570H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G202570H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G202070H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300470h.prelist merge count = 13 photon cnt = 14240 GISSORTSPLIT:LO:g300570h.prelist merge count = 3 photon cnt = 4 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300270m.prelist merge count = 2 photon cnt = 20 GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300470m.prelist merge count = 3 photon cnt = 11 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g300770m.prelist merge count = 13 photon cnt = 11601 GISSORTSPLIT:LO:g300870m.prelist merge count = 7 photon cnt = 317 GISSORTSPLIT:LO:Total filenames split = 59 GISSORTSPLIT:LO:Total split file cnt = 24 GISSORTSPLIT:LO:End program-> Creating ad81009000g300170h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958G300570H.fits 2 -- ft931102_0609_1958G301370H.fits 3 -- ft931102_0609_1958G301670H.fits 4 -- ft931102_0609_1958G302170H.fits 5 -- ft931102_0609_1958G302370H.fits 6 -- ft931102_0609_1958G302670H.fits 7 -- ft931102_0609_1958G303370H.fits 8 -- ft931102_0609_1958G303570H.fits 9 -- ft931102_0609_1958G304470H.fits 10 -- ft931102_0609_1958G305470H.fits 11 -- ft931102_0609_1958G306170H.fits 12 -- ft931102_0609_1958G306370H.fits 13 -- ft931102_0609_1958G307470H.fits Merging binary extension #: 2 1 -- ft931102_0609_1958G300570H.fits 2 -- ft931102_0609_1958G301370H.fits 3 -- ft931102_0609_1958G301670H.fits 4 -- ft931102_0609_1958G302170H.fits 5 -- ft931102_0609_1958G302370H.fits 6 -- ft931102_0609_1958G302670H.fits 7 -- ft931102_0609_1958G303370H.fits 8 -- ft931102_0609_1958G303570H.fits 9 -- ft931102_0609_1958G304470H.fits 10 -- ft931102_0609_1958G305470H.fits 11 -- ft931102_0609_1958G306170H.fits 12 -- ft931102_0609_1958G306370H.fits 13 -- ft931102_0609_1958G307470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000g300270m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958G300170M.fits 2 -- ft931102_0609_1958G300770M.fits 3 -- ft931102_0609_1958G300970M.fits 4 -- ft931102_0609_1958G301570M.fits 5 -- ft931102_0609_1958G301870M.fits 6 -- ft931102_0609_1958G302070M.fits 7 -- ft931102_0609_1958G302970M.fits 8 -- ft931102_0609_1958G304070M.fits 9 -- ft931102_0609_1958G304670M.fits 10 -- ft931102_0609_1958G305070M.fits 11 -- ft931102_0609_1958G305670M.fits 12 -- ft931102_0609_1958G306070M.fits 13 -- ft931102_0609_1958G306970M.fits Merging binary extension #: 2 1 -- ft931102_0609_1958G300170M.fits 2 -- ft931102_0609_1958G300770M.fits 3 -- ft931102_0609_1958G300970M.fits 4 -- ft931102_0609_1958G301570M.fits 5 -- ft931102_0609_1958G301870M.fits 6 -- ft931102_0609_1958G302070M.fits 7 -- ft931102_0609_1958G302970M.fits 8 -- ft931102_0609_1958G304070M.fits 9 -- ft931102_0609_1958G304670M.fits 10 -- ft931102_0609_1958G305070M.fits 11 -- ft931102_0609_1958G305670M.fits 12 -- ft931102_0609_1958G306070M.fits 13 -- ft931102_0609_1958G306970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000317 events
ft931102_0609_1958G300670M.fits ft931102_0609_1958G301470M.fits ft931102_0609_1958G301770M.fits ft931102_0609_1958G302770M.fits ft931102_0609_1958G303670M.fits ft931102_0609_1958G304570M.fits ft931102_0609_1958G305570M.fits-> Ignoring the following files containing 000000020 events
ft931102_0609_1958G304770M.fits ft931102_0609_1958G305770M.fits-> Ignoring the following files containing 000000017 events
ft931102_0609_1958G301970M.fits-> Ignoring the following files containing 000000015 events
ft931102_0609_1958G306870M.fits-> Ignoring the following files containing 000000011 events
ft931102_0609_1958G303970M.fits ft931102_0609_1958G304970M.fits ft931102_0609_1958G305970M.fits-> Ignoring the following files containing 000000007 events
ft931102_0609_1958G307170H.fits-> Ignoring the following files containing 000000007 events
ft931102_0609_1958G302870M.fits-> Ignoring the following files containing 000000006 events
ft931102_0609_1958G303470H.fits-> Ignoring the following files containing 000000005 events
ft931102_0609_1958G305270H.fits-> Ignoring the following files containing 000000005 events
ft931102_0609_1958G302470H.fits-> Ignoring the following files containing 000000004 events
ft931102_0609_1958G301170H.fits-> Ignoring the following files containing 000000004 events
ft931102_0609_1958G301070H.fits-> Ignoring the following files containing 000000004 events
ft931102_0609_1958G304170H.fits-> Ignoring the following files containing 000000004 events
ft931102_0609_1958G300470H.fits ft931102_0609_1958G301270H.fits ft931102_0609_1958G305370H.fits-> Ignoring the following files containing 000000004 events
ft931102_0609_1958G303770M.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G305170H.fits-> Ignoring the following files containing 000000003 events
ft931102_0609_1958G302570H.fits-> Ignoring the following files containing 000000002 events
ft931102_0609_1958G307270H.fits-> Ignoring the following files containing 000000002 events
ft931102_0609_1958G304270H.fits-> Ignoring the following files containing 000000002 events
ft931102_0609_1958G300370H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G303070H.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958G300270H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 11 photon cnt = 337489 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 250 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 6 photon cnt = 112597 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 1 photon cnt = 192 SIS0SORTSPLIT:LO:s000502m.prelist merge count = 11 photon cnt = 107481 SIS0SORTSPLIT:LO:s000602m.prelist merge count = 6 photon cnt = 7538 SIS0SORTSPLIT:LO:s000702m.prelist merge count = 1 photon cnt = 1 SIS0SORTSPLIT:LO:Total filenames split = 37 SIS0SORTSPLIT:LO:Total split file cnt = 7 SIS0SORTSPLIT:LO:End program-> Creating ad81009000s000101h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S000301H.fits 2 -- ft931102_0609_1958S001001H.fits 3 -- ft931102_0609_1958S001401H.fits 4 -- ft931102_0609_1958S001901H.fits 5 -- ft931102_0609_1958S002101H.fits 6 -- ft931102_0609_1958S002901H.fits 7 -- ft931102_0609_1958S003601H.fits 8 -- ft931102_0609_1958S004301H.fits 9 -- ft931102_0609_1958S005001H.fits 10 -- ft931102_0609_1958S005201H.fits 11 -- ft931102_0609_1958S006101H.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S000301H.fits 2 -- ft931102_0609_1958S001001H.fits 3 -- ft931102_0609_1958S001401H.fits 4 -- ft931102_0609_1958S001901H.fits 5 -- ft931102_0609_1958S002101H.fits 6 -- ft931102_0609_1958S002901H.fits 7 -- ft931102_0609_1958S003601H.fits 8 -- ft931102_0609_1958S004301H.fits 9 -- ft931102_0609_1958S005001H.fits 10 -- ft931102_0609_1958S005201H.fits 11 -- ft931102_0609_1958S006101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000s000201h.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S000401H.fits 2 -- ft931102_0609_1958S001101H.fits 3 -- ft931102_0609_1958S002201H.fits 4 -- ft931102_0609_1958S003001H.fits 5 -- ft931102_0609_1958S004401H.fits 6 -- ft931102_0609_1958S005301H.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S000401H.fits 2 -- ft931102_0609_1958S001101H.fits 3 -- ft931102_0609_1958S002201H.fits 4 -- ft931102_0609_1958S003001H.fits 5 -- ft931102_0609_1958S004401H.fits 6 -- ft931102_0609_1958S005301H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000s000302m.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S000202M.fits 2 -- ft931102_0609_1958S000702M.fits 3 -- ft931102_0609_1958S000902M.fits 4 -- ft931102_0609_1958S001602M.fits 5 -- ft931102_0609_1958S001802M.fits 6 -- ft931102_0609_1958S002802M.fits 7 -- ft931102_0609_1958S003502M.fits 8 -- ft931102_0609_1958S003802M.fits 9 -- ft931102_0609_1958S004202M.fits 10 -- ft931102_0609_1958S004902M.fits 11 -- ft931102_0609_1958S005802M.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S000202M.fits 2 -- ft931102_0609_1958S000702M.fits 3 -- ft931102_0609_1958S000902M.fits 4 -- ft931102_0609_1958S001602M.fits 5 -- ft931102_0609_1958S001802M.fits 6 -- ft931102_0609_1958S002802M.fits 7 -- ft931102_0609_1958S003502M.fits 8 -- ft931102_0609_1958S003802M.fits 9 -- ft931102_0609_1958S004202M.fits 10 -- ft931102_0609_1958S004902M.fits 11 -- ft931102_0609_1958S005802M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000s000402m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S000102M.fits 2 -- ft931102_0609_1958S001302M.fits 3 -- ft931102_0609_1958S002702M.fits 4 -- ft931102_0609_1958S003202M.fits 5 -- ft931102_0609_1958S003402M.fits 6 -- ft931102_0609_1958S003902M.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S000102M.fits 2 -- ft931102_0609_1958S001302M.fits 3 -- ft931102_0609_1958S002702M.fits 4 -- ft931102_0609_1958S003202M.fits 5 -- ft931102_0609_1958S003402M.fits 6 -- ft931102_0609_1958S003902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000250 events
ft931102_0609_1958S002001H.fits-> Ignoring the following files containing 000000192 events
ft931102_0609_1958S005901M.fits-> Ignoring the following files containing 000000001 events
ft931102_0609_1958S005602M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 246 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 208 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 11 photon cnt = 504153 SIS1SORTSPLIT:LO:s100401m.prelist merge count = 1 photon cnt = 191 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 1 photon cnt = 852 SIS1SORTSPLIT:LO:s100602m.prelist merge count = 13 photon cnt = 167004 SIS1SORTSPLIT:LO:Total filenames split = 28 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad81009000s100101h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S100201H.fits 2 -- ft931102_0609_1958S100701H.fits 3 -- ft931102_0609_1958S101301H.fits 4 -- ft931102_0609_1958S101501H.fits 5 -- ft931102_0609_1958S101701H.fits 6 -- ft931102_0609_1958S102001H.fits 7 -- ft931102_0609_1958S102501H.fits 8 -- ft931102_0609_1958S103001H.fits 9 -- ft931102_0609_1958S103501H.fits 10 -- ft931102_0609_1958S103701H.fits 11 -- ft931102_0609_1958S104401H.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S100201H.fits 2 -- ft931102_0609_1958S100701H.fits 3 -- ft931102_0609_1958S101301H.fits 4 -- ft931102_0609_1958S101501H.fits 5 -- ft931102_0609_1958S101701H.fits 6 -- ft931102_0609_1958S102001H.fits 7 -- ft931102_0609_1958S102501H.fits 8 -- ft931102_0609_1958S103001H.fits 9 -- ft931102_0609_1958S103501H.fits 10 -- ft931102_0609_1958S103701H.fits 11 -- ft931102_0609_1958S104401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad81009000s100202m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft931102_0609_1958S100102M.fits 2 -- ft931102_0609_1958S100402M.fits 3 -- ft931102_0609_1958S100602M.fits 4 -- ft931102_0609_1958S100902M.fits 5 -- ft931102_0609_1958S101202M.fits 6 -- ft931102_0609_1958S101902M.fits 7 -- ft931102_0609_1958S102202M.fits 8 -- ft931102_0609_1958S102402M.fits 9 -- ft931102_0609_1958S102702M.fits 10 -- ft931102_0609_1958S102902M.fits 11 -- ft931102_0609_1958S103202M.fits 12 -- ft931102_0609_1958S103402M.fits 13 -- ft931102_0609_1958S104102M.fits Merging binary extension #: 2 1 -- ft931102_0609_1958S100102M.fits 2 -- ft931102_0609_1958S100402M.fits 3 -- ft931102_0609_1958S100602M.fits 4 -- ft931102_0609_1958S100902M.fits 5 -- ft931102_0609_1958S101202M.fits 6 -- ft931102_0609_1958S101902M.fits 7 -- ft931102_0609_1958S102202M.fits 8 -- ft931102_0609_1958S102402M.fits 9 -- ft931102_0609_1958S102702M.fits 10 -- ft931102_0609_1958S102902M.fits 11 -- ft931102_0609_1958S103202M.fits 12 -- ft931102_0609_1958S103402M.fits 13 -- ft931102_0609_1958S104102M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000852 events
ft931102_0609_1958S101102M.fits-> Ignoring the following files containing 000000246 events
ft931102_0609_1958S101601H.fits-> Ignoring the following files containing 000000208 events
ft931102_0609_1958S101401H.fits-> Ignoring the following files containing 000000191 events
ft931102_0609_1958S104201M.fits-> Tar-ing together the leftover raw files
a ft931102_0609_1958G200270H.fits 40K a ft931102_0609_1958G200370H.fits 40K a ft931102_0609_1958G200470H.fits 40K a ft931102_0609_1958G200670M.fits 40K a ft931102_0609_1958G201070H.fits 40K a ft931102_0609_1958G201170H.fits 40K a ft931102_0609_1958G201270H.fits 40K a ft931102_0609_1958G201470M.fits 40K a ft931102_0609_1958G201770M.fits 40K a ft931102_0609_1958G202070H.fits 40K a ft931102_0609_1958G202270M.fits 40K a ft931102_0609_1958G202370M.fits 40K a ft931102_0609_1958G202570H.fits 40K a ft931102_0609_1958G202770H.fits 40K a ft931102_0609_1958G202970M.fits 40K a ft931102_0609_1958G203070M.fits 40K a ft931102_0609_1958G203270M.fits 40K a ft931102_0609_1958G203470H.fits 40K a ft931102_0609_1958G203570H.fits 40K a ft931102_0609_1958G203670H.fits 40K a ft931102_0609_1958G203870M.fits 40K a ft931102_0609_1958G204070M.fits 40K a ft931102_0609_1958G204270M.fits 40K a ft931102_0609_1958G204470H.fits 40K a ft931102_0609_1958G204570H.fits 40K a ft931102_0609_1958G204670H.fits 40K a ft931102_0609_1958G204870M.fits 40K a ft931102_0609_1958G205070M.fits 40K a ft931102_0609_1958G205270M.fits 40K a ft931102_0609_1958G206170M.fits 40K a ft931102_0609_1958G206470H.fits 40K a ft931102_0609_1958G206570H.fits 40K a ft931102_0609_1958G300270H.fits 40K a ft931102_0609_1958G300370H.fits 40K a ft931102_0609_1958G300470H.fits 40K a ft931102_0609_1958G300670M.fits 40K a ft931102_0609_1958G301070H.fits 40K a ft931102_0609_1958G301170H.fits 40K a ft931102_0609_1958G301270H.fits 40K a ft931102_0609_1958G301470M.fits 40K a ft931102_0609_1958G301770M.fits 40K a ft931102_0609_1958G301970M.fits 40K a ft931102_0609_1958G302470H.fits 40K a ft931102_0609_1958G302570H.fits 40K a ft931102_0609_1958G302770M.fits 40K a ft931102_0609_1958G302870M.fits 40K a ft931102_0609_1958G303070H.fits 40K a ft931102_0609_1958G303470H.fits 40K a ft931102_0609_1958G303670M.fits 40K a ft931102_0609_1958G303770M.fits 40K a ft931102_0609_1958G303970M.fits 40K a ft931102_0609_1958G304170H.fits 40K a ft931102_0609_1958G304270H.fits 40K a ft931102_0609_1958G304570M.fits 40K a ft931102_0609_1958G304770M.fits 40K a ft931102_0609_1958G304970M.fits 40K a ft931102_0609_1958G305170H.fits 40K a ft931102_0609_1958G305270H.fits 40K a ft931102_0609_1958G305370H.fits 40K a ft931102_0609_1958G305570M.fits 40K a ft931102_0609_1958G305770M.fits 40K a ft931102_0609_1958G305970M.fits 40K a ft931102_0609_1958G306870M.fits 40K a ft931102_0609_1958G307170H.fits 40K a ft931102_0609_1958G307270H.fits 40K a ft931102_0609_1958S002001H.fits 48K a ft931102_0609_1958S005602M.fits 40K a ft931102_0609_1958S005901M.fits 45K a ft931102_0609_1958S101102M.fits 62K a ft931102_0609_1958S101401H.fits 45K a ft931102_0609_1958S101601H.fits 48K a ft931102_0609_1958S104201M.fits 45K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft931102_0609.1958 'ft931102_0609.1958' is successfully opened Data Start Time is 26374160.83 (931102 060920) Time Margin 2.0 sec included Sync error detected in 3179 th SF Sync error detected in 3180 th SF Sync error detected in 3181 th SF Sync error detected in 3182 th SF Sync error detected in 3184 th SF Sync error detected in 3186 th SF Sync error detected in 3187 th SF Sync error detected in 3189 th SF Sync error detected in 3190 th SF Sync error detected in 3191 th SF Sync error detected in 3198 th SF Sync error detected in 3201 th SF Sync error detected in 3202 th SF Sync error detected in 3203 th SF Sync error detected in 3205 th SF Sync error detected in 3208 th SF Sync error detected in 3209 th SF Sync error detected in 3210 th SF Sync error detected in 3211 th SF Sync error detected in 3212 th SF Sync error detected in 3213 th SF Sync error detected in 3214 th SF Sync error detected in 3215 th SF Sync error detected in 3216 th SF Sync error detected in 3217 th SF Sync error detected in 3218 th SF Sync error detected in 3219 th SF Sync error detected in 3220 th SF Sync error detected in 3221 th SF Sync error detected in 3222 th SF Sync error detected in 3223 th SF Sync error detected in 3224 th SF Sync error detected in 3225 th SF Sync error detected in 3226 th SF Sync error detected in 3227 th SF Sync error detected in 3228 th SF Sync error detected in 3229 th SF Sync error detected in 3248 th SF Sync error detected in 3249 th SF Sync error detected in 3250 th SF Sync error detected in 3251 th SF Sync error detected in 3256 th SF Sync error detected in 3257 th SF Sync error detected in 3258 th SF Sync error detected in 3262 th SF Sync error detected in 3277 th SF Sync error detected in 3278 th SF Sync error detected in 3279 th SF Sync error detected in 3280 th SF Sync error detected in 3281 th SF Sync error detected in 3282 th SF Sync error detected in 3285 th SF Sync error detected in 3286 th SF Sync error detected in 3294 th SF Sync error detected in 3299 th SF Sync error detected in 3300 th SF Sync error detected in 3303 th SF Sync error detected in 3305 th SF Sync error detected in 3306 th SF Sync error detected in 3313 th SF Sync error detected in 3315 th SF Sync error detected in 3316 th SF Sync error detected in 3317 th SF Sync error detected in 3318 th SF Sync error detected in 3319 th SF Sync error detected in 3320 th SF Sync error detected in 3321 th SF Sync error detected in 3322 th SF Sync error detected in 3323 th SF Sync error detected in 3325 th SF Sync error detected in 3327 th SF Sync error detected in 3344 th SF Sync error detected in 3347 th SF Sync error detected in 3351 th SF Sync error detected in 3371 th SF Sync error detected in 3379 th SF Sync error detected in 3389 th SF Sync error detected in 3455 th SF Sync error detected in 3711 th SF Sync error detected in 3722 th SF Sync error detected in 3737 th SF Sync error detected in 6019 th SF Sync error detected in 6025 th SF Sync error detected in 6026 th SF Sync error detected in 6027 th SF Sync error detected in 6029 th SF 'ft931102_0609.1958' EOF detected, sf=10104 Data End Time is 26423922.67 (931102 195842) Gain History is written in ft931102_0609_1958.ghf-> Checking if column CAL_START in ft931102_0609_1958.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft931102_0609_1958.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad81009000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26386829.790039 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 26389677.780426 ASCALIN_V0.9t : Detected gap > 15min in attitude file:
Date and time are: 93/11/ 2 6: 9 mjd=49293.256250 Orbit file name is ./frf.orbit.209 Epoch of Orbital Elements: 1993/11/2 0:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa931102_0609.1958 S0-HK file: ft931102_0609_1958S0HK.fits S1-HK file: ft931102_0609_1958S1HK.fits G2-HK file: ft931102_0609_1958G2HK.fits G3-HK file: ft931102_0609_1958G3HK.fits output FITS File: ft931102_0609_1958.mkf Total 1557 Data bins were processed.-> Checking if column TIME in ft931102_0609_1958.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 2095.5692 The mean of the selected column is 27.573279 The standard deviation of the selected column is 8.7506602 The minimum of selected column is 13.406292 The maximum of selected column is 55.031425 The number of points used in calculation is 76-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1668.2085 The mean of the selected column is 21.665045 The standard deviation of the selected column is 8.2767309 The minimum of selected column is 8.1250257 The maximum of selected column is 46.000149 The number of points used in calculation is 77-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1903.0687 The mean of the selected column is 27.186696 The standard deviation of the selected column is 16.206525 The minimum of selected column is 10.218782 The maximum of selected column is 120.00039 The number of points used in calculation is 70-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1930.5062 The mean of the selected column is 26.445290 The standard deviation of the selected column is 11.548051 The minimum of selected column is 10.125031 The maximum of selected column is 62.468952 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.3 && S0_PIXL0<53.8 )&& (S0_PIXL1>0.0 && S0_PIXL1<46.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<75.8 )&& (S0_PIXL3>0.0 && S0_PIXL3<61 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.15E+05 246228 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
232777 32588 0 200189 0 0
Writing events file
32588 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
232777 32588 0 200189 0 0
in 2137.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 32588
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 106 12756
Flickering pixels iter, pixels & cnts : 1 92 1423
cleaning chip # 1
Hot pixels & counts : 58 5213
Flickering pixels iter, pixels & cnts : 1 69 695
cleaning chip # 2
Hot pixels & counts : 60 5121
Flickering pixels iter, pixels & cnts : 1 95 879
cleaning chip # 3
Hot pixels & counts : 53 5081
Flickering pixels iter, pixels & cnts : 1 66 586
Number of pixels rejected : 599
Number of (internal) image counts : 32588
Number of image cts rejected (N, %) : 31754 97.4407730
By chip : 0 1 2 3
Pixels rejected : 198 127 155 119
Image counts : 14382 6094 6270 5842
Image cts rejected: 14179 5908 6000 5667
Image cts rej (%) : 98.59 96.95 95.69 97.00
filtering data...
Total counts : 14382 6094 6270 5842
Total cts rejected: 14179 5908 6000 5667
Total cts rej (%) : 98.59 96.95 95.69 97.00
Number of clean counts accepted : 834
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 599
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad81009000s000102h.evt use_events=no
Wrote cleaned events file to ad81009000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad81009000s000112h.unf into ad81009000s000112h.evtThe sum of the selected column is 2095.5692 The mean of the selected column is 27.573279 The standard deviation of the selected column is 8.7506602 The minimum of selected column is 13.406292 The maximum of selected column is 55.031425 The number of points used in calculation is 76-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1668.2085 The mean of the selected column is 21.665045 The standard deviation of the selected column is 8.2767309 The minimum of selected column is 8.1250257 The maximum of selected column is 46.000149 The number of points used in calculation is 77-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1903.0687 The mean of the selected column is 27.186696 The standard deviation of the selected column is 16.206525 The minimum of selected column is 10.218782 The maximum of selected column is 120.00039 The number of points used in calculation is 70-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1930.5062 The mean of the selected column is 26.445290 The standard deviation of the selected column is 11.548051 The minimum of selected column is 10.125031 The maximum of selected column is 62.468952 The number of points used in calculation is 73-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.3 && S0_PIXL0<53.8 )&& (S0_PIXL1>0.0 && S0_PIXL1<46.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<75.8 )&& (S0_PIXL3>0.0 && S0_PIXL3<61 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.15E+05 255477 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
234106 32736 0 201370 0 0
Writing events file
32736 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
234106 32736 0 201370 0 0
in 2137.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 32736
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 105 12750
Flickering pixels iter, pixels & cnts : 1 93 1444
cleaning chip # 1
Hot pixels & counts : 59 5255
Flickering pixels iter, pixels & cnts : 1 68 677
cleaning chip # 2
Hot pixels & counts : 60 5148
Flickering pixels iter, pixels & cnts : 1 96 886
cleaning chip # 3
Hot pixels & counts : 54 5128
Flickering pixels iter, pixels & cnts : 1 65 567
Number of pixels rejected : 600
Number of (internal) image counts : 32736
Number of image cts rejected (N, %) : 31855 97.3087769
By chip : 0 1 2 3
Pixels rejected : 198 127 156 119
Image counts : 14408 6132 6319 5877
Image cts rejected: 14194 5932 6034 5695
Image cts rej (%) : 98.51 96.74 95.49 96.90
filtering data...
Total counts : 14408 6132 6319 5877
Total cts rejected: 14194 5932 6034 5695
Total cts rej (%) : 98.51 96.74 95.49 96.90
Number of clean counts accepted : 881
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 600
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad81009000s000112h.evt use_events=no
Wrote cleaned events file to ad81009000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad81009000s000201h.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 07:34:58 0.18E+04 37057 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad81009000s000202h.evt use_events=no
Wrote cleaned events file to ad81009000s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad81009000s000202h.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 07:34:58 0.18E+04 43600 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad81009000s000212h.evt use_events=no
Wrote cleaned events file to ad81009000s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad81009000s000212h.evt since it contains 0 eventsThe sum of the selected column is 628.37695 The mean of the selected column is 24.168344 The standard deviation of the selected column is 13.163651 The minimum of selected column is 12.125037 The maximum of selected column is 77.781494 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 421.90756 The mean of the selected column is 16.227214 The standard deviation of the selected column is 6.0805949 The minimum of selected column is 8.1875257 The maximum of selected column is 36.531364 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 556.09547 The mean of the selected column is 21.388287 The standard deviation of the selected column is 10.634460 The minimum of selected column is 8.8437777 The maximum of selected column is 47.718899 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 513.87660 The mean of the selected column is 19.764484 The standard deviation of the selected column is 7.2629055 The minimum of selected column is 8.3437757 The maximum of selected column is 43.312634 The number of points used in calculation is 26-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<63.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<34.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<53.2 )&& (S0_PIXL3>0.0 && S0_PIXL3<41.5 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.72E+04 107481 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
101589 10778 0 90811 0 0
Writing events file
10778 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
101589 10778 0 90811 0 0
in 736.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 10778
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 96 4165
Flickering pixels iter, pixels & cnts : 1 59 531
cleaning chip # 1
Hot pixels & counts : 46 1631
Flickering pixels iter, pixels & cnts : 1 44 285
cleaning chip # 2
Hot pixels & counts : 48 1635
Flickering pixels iter, pixels & cnts : 1 39 290
cleaning chip # 3
Hot pixels & counts : 43 1637
Flickering pixels iter, pixels & cnts : 1 36 239
Number of pixels rejected : 411
Number of (internal) image counts : 10778
Number of image cts rejected (N, %) : 10413 96.6134720
By chip : 0 1 2 3
Pixels rejected : 155 90 87 79
Image counts : 4794 1998 2038 1948
Image cts rejected: 4696 1916 1925 1876
Image cts rej (%) : 97.96 95.90 94.46 96.30
filtering data...
Total counts : 4794 1998 2038 1948
Total cts rejected: 4696 1916 1925 1876
Total cts rej (%) : 97.96 95.90 94.46 96.30
Number of clean counts accepted : 365
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 411
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad81009000s000302m.evt use_events=no
Wrote cleaned events file to ad81009000s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad81009000s000402m.unf into ad81009000s000402m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.38E+04 7538 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad81009000s000402m.evt use_events=no
Wrote cleaned events file to ad81009000s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad81009000s000402m.evt since it contains 0 eventsThe sum of the selected column is 2693.0243 The mean of the selected column is 34.088916 The standard deviation of the selected column is 14.551454 The minimum of selected column is 11.000034 The maximum of selected column is 82.250267 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2925.3219 The mean of the selected column is 37.029392 The standard deviation of the selected column is 13.774002 The minimum of selected column is 12.187599 The maximum of selected column is 79.437759 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2546.0394 The mean of the selected column is 32.228347 The standard deviation of the selected column is 13.397799 The minimum of selected column is 8.4375257 The maximum of selected column is 88.906540 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3032.7285 The mean of the selected column is 38.388968 The standard deviation of the selected column is 16.578505 The minimum of selected column is 9.3437796 The maximum of selected column is 119.65663 The number of points used in calculation is 79-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<77.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<78.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<72.4 )&& (S1_PIXL3>0.0 && S1_PIXL3<88.1 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.17E+05 357738 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
327553 46990 0 280563 0 0
Writing events file
46990 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
327553 46990 0 280563 0 0
in 2425.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 46990
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 76 8297
Flickering pixels iter, pixels & cnts : 1 114 1427
Flickering pixels iter, pixels & cnts : 2 2 6
cleaning chip # 1
Hot pixels & counts : 99 11145
Flickering pixels iter, pixels & cnts : 1 159 2215
Flickering pixels iter, pixels & cnts : 2 3 11
cleaning chip # 2
Hot pixels & counts : 70 8324
Flickering pixels iter, pixels & cnts : 1 94 1124
cleaning chip # 3
Hot pixels & counts : 92 10880
Flickering pixels iter, pixels & cnts : 1 159 2488
Number of pixels rejected : 868
Number of (internal) image counts : 46990
Number of image cts rejected (N, %) : 45917 97.7165375
By chip : 0 1 2 3
Pixels rejected : 192 261 164 251
Image counts : 10018 13632 9682 13658
Image cts rejected: 9730 13371 9448 13368
Image cts rej (%) : 97.13 98.09 97.58 97.88
filtering data...
Total counts : 10018 13632 9682 13658
Total cts rejected: 9730 13371 9448 13368
Total cts rej (%) : 97.13 98.09 97.58 97.88
Number of clean counts accepted : 1073
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 868
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad81009000s100102h.evt use_events=no
Wrote cleaned events file to ad81009000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad81009000s100112h.unf into ad81009000s100112h.evtThe sum of the selected column is 2693.0243 The mean of the selected column is 34.088916 The standard deviation of the selected column is 14.551454 The minimum of selected column is 11.000034 The maximum of selected column is 82.250267 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2925.3219 The mean of the selected column is 37.029392 The standard deviation of the selected column is 13.774002 The minimum of selected column is 12.187599 The maximum of selected column is 79.437759 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2546.0394 The mean of the selected column is 32.228347 The standard deviation of the selected column is 13.397799 The minimum of selected column is 8.4375257 The maximum of selected column is 88.906540 The number of points used in calculation is 79-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3032.7285 The mean of the selected column is 38.388968 The standard deviation of the selected column is 16.578505 The minimum of selected column is 9.3437796 The maximum of selected column is 119.65663 The number of points used in calculation is 79-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<77.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<78.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<72.4 )&& (S1_PIXL3>0.0 && S1_PIXL3<88.1 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.17E+05 371690 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
332420 47641 0 284779 0 0
Writing events file
47641 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
332420 47641 0 284779 0 0
in 2425.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 47641
Total counts in chip images : 47640
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 77 8439
Flickering pixels iter, pixels & cnts : 1 122 1503
Flickering pixels iter, pixels & cnts : 2 2 6
cleaning chip # 1
Hot pixels & counts : 99 11253
Flickering pixels iter, pixels & cnts : 1 162 2277
Flickering pixels iter, pixels & cnts : 2 3 11
cleaning chip # 2
Hot pixels & counts : 71 8420
Flickering pixels iter, pixels & cnts : 1 92 1103
cleaning chip # 3
Hot pixels & counts : 94 11076
Flickering pixels iter, pixels & cnts : 1 158 2442
Number of pixels rejected : 880
Number of (internal) image counts : 47640
Number of image cts rejected (N, %) : 46530 97.6700287
By chip : 0 1 2 3
Pixels rejected : 201 264 163 252
Image counts : 10237 13808 9779 13816
Image cts rejected: 9948 13541 9523 13518
Image cts rej (%) : 97.18 98.07 97.38 97.84
filtering data...
Total counts : 10237 13809 9779 13816
Total cts rejected: 9948 13542 9523 13518
Total cts rej (%) : 97.18 98.07 97.38 97.84
Number of clean counts accepted : 1110
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 880
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad81009000s100112h.evt use_events=no
Wrote cleaned events file to ad81009000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad81009000s100202m.unf into ad81009000s100202m.evtThe sum of the selected column is 664.28332 The mean of the selected column is 25.549358 The standard deviation of the selected column is 7.6560479 The minimum of selected column is 12.468789 The maximum of selected column is 45.250141 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 706.68969 The mean of the selected column is 27.180373 The standard deviation of the selected column is 7.5763036 The minimum of selected column is 12.125037 The maximum of selected column is 42.687634 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 642.09574 The mean of the selected column is 24.695990 The standard deviation of the selected column is 7.8982619 The minimum of selected column is 11.687536 The maximum of selected column is 45.968891 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 831.97132 The mean of the selected column is 31.998897 The standard deviation of the selected column is 13.687754 The minimum of selected column is 14.125044 The maximum of selected column is 79.968994 The number of points used in calculation is 26-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>2.5 && S1_PIXL0<48.5 )&& (S1_PIXL1>4.4 && S1_PIXL1<49.9 )&& (S1_PIXL2>1 && S1_PIXL2<48.3 )&& (S1_PIXL3>0.0 && S1_PIXL3<73 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.13E+05 167004 1111
Processing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
149731 15221 0 134510 0 0
Writing events file
15221 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
149731 15221 0 134510 0 0
in 800.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/81009000.006/screen_in_event.xsl
reading data file: /data/data24/seq_proc/81009000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 15221
Total counts in chip images : 15220
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 63 2543
Flickering pixels iter, pixels & cnts : 1 67 495
cleaning chip # 1
Hot pixels & counts : 79 3305
Flickering pixels iter, pixels & cnts : 1 97 908
cleaning chip # 2
Hot pixels & counts : 62 2586
Flickering pixels iter, pixels & cnts : 1 58 419
cleaning chip # 3
Hot pixels & counts : 80 3404
Flickering pixels iter, pixels & cnts : 1 99 1020
Number of pixels rejected : 605
Number of (internal) image counts : 15220
Number of image cts rejected (N, %) : 14680 96.4520340
By chip : 0 1 2 3
Pixels rejected : 130 176 120 179
Image counts : 3168 4356 3117 4579
Image cts rejected: 3038 4213 3005 4424
Image cts rej (%) : 95.90 96.72 96.41 96.61
filtering data...
Total counts : 3168 4356 3117 4580
Total cts rejected: 3038 4213 3005 4425
Total cts rej (%) : 95.90 96.72 96.41 96.62
Number of clean counts accepted : 540
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 605
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad81009000s100202m.evt use_events=no
Wrote cleaned events file to ad81009000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad81009000g200170h.unf into ad81009000g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 15247 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.unf
Total Good Bad: Region Time Phase Cut
15247 766 10172 4309 0 0
Writing events file
766 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15247 766 10172 4309 0 0
in 2671.87 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
766 670 96
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad81009000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 670 in ad81009000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 12449 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.unf
Total Good Bad: Region Time Phase Cut
12449 306 7001 5142 0 0
Writing events file
306 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12449 306 7001 5142 0 0
in 1072.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
306 268 38
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad81009000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 268 in ad81009000g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 14240 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.unf
Total Good Bad: Region Time Phase Cut
14240 815 8946 4479 0 0
Writing events file
815 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14240 815 8946 4479 0 0
in 2671.87 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
815 708 107
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad81009000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 708 in ad81009000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 11601 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.unf
Total Good Bad: Region Time Phase Cut
11601 345 6037 5219 0 0
Writing events file
345 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11601 345 6037 5219 0 0
in 1072.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
345 300 45
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!screen:ASCA > read events ad81009000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad81009000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 300 in ad81009000g300270m.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad81009000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7859
Mean RA/DEC/ROLL : 112.6811 31.3885 259.7859
Pnt RA/DEC/ROLL : 112.7383 31.4363 259.7859
Image rebin factor : 1
Attitude Records : 39532
GTI intervals : 2
Total GTI (secs) : 2671.867
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 408.3737488 408.3737488
20 Percent Complete: Total/live time: 668.3729248 668.3729248
30 Percent Complete: Total/live time: 1106.3715820 1106.3715820
40 Percent Complete: Total/live time: 1106.3715820 1106.3715820
50 Percent Complete: Total/live time: 1583.3701172 1583.3701172
60 Percent Complete: Total/live time: 2080.8684082 2080.8684082
70 Percent Complete: Total/live time: 2080.8684082 2080.8684082
80 Percent Complete: Total/live time: 2607.8666992 2607.8666992
90 Percent Complete: Total/live time: 2607.8666992 2607.8666992
100 Percent Complete: Total/live time: 2671.8666992 2671.8666992
Number of attitude steps used: 19
Number of attitude steps avail: 5350
Mean RA/DEC pixel offset: -9.9145 -2.0937
writing expo file: ad81009000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 657 13 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
670 657 13 0 0 0
in 2671.87 seconds
Image has 657 counts for 0.2459 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 284 13 0 0 373
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
670 284 13 0 0 373
in 2671.87 seconds
Image has 284 counts for 0.1063 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 375 13 0 0 282
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
670 375 13 0 0 282
in 2671.87 seconds
Image has 375 counts for 0.1404 counts/sec
Command not found; type ? for a command listing
!ad81009000g200170h:ASCA >
!ad81009000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000g200170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000g200170h:ASCA > read events ad81009000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000g200170h:ASCA-GIS2-PH > set image sky
!ad81009000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad81009000g200170h:ASCA-GIS2-PH > extract image
!ad81009000g200170h:ASCA-GIS2-PH > save image outfile=ad81009000g200170h.img
Wrote image to file ad81009000g200170h.img
!ad81009000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad81009000g200170h:ASCA-GIS2-PH > extract image
!ad81009000g200170h:ASCA-GIS2-PH > save image outfile=ad81009000g200170h_lo.img
Wrote image to file ad81009000g200170h_lo.img
!ad81009000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad81009000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad81009000g200170h:ASCA-GIS2-PH > extract image
!ad81009000g200170h:ASCA-GIS2-PH > save image outfile=ad81009000g200170h_hi.img
Wrote image to file ad81009000g200170h_hi.img
!ad81009000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad81009000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad81009000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7776
Mean RA/DEC/ROLL : 112.6662 31.4057 259.7776
Pnt RA/DEC/ROLL : 112.6574 31.2916 259.7776
Image rebin factor : 1
Attitude Records : 39532
GTI intervals : 2
Total GTI (secs) : 1072.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 143.9995880 143.9995880
20 Percent Complete: Total/live time: 282.8580933 282.8580933
30 Percent Complete: Total/live time: 394.8578796 394.8578796
40 Percent Complete: Total/live time: 486.8575439 486.8575439
50 Percent Complete: Total/live time: 570.8572388 570.8572388
60 Percent Complete: Total/live time: 666.8568115 666.8568115
70 Percent Complete: Total/live time: 838.8562622 838.8562622
80 Percent Complete: Total/live time: 986.8558350 986.8558350
90 Percent Complete: Total/live time: 986.8558350 986.8558350
100 Percent Complete: Total/live time: 1071.9995117 1071.9995117
Number of attitude steps used: 20
Number of attitude steps avail: 415
Mean RA/DEC pixel offset: -10.9953 -1.2501
writing expo file: ad81009000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 268 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
in 1072.00 seconds
Image has 268 counts for 0.2500 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 115 0 0 0 153
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
268 115 0 0 0 153
in 1072.00 seconds
Image has 115 counts for 0.1073 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 153 0 0 0 115
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
268 153 0 0 0 115
in 1072.00 seconds
Image has 153 counts for 0.1427 counts/sec
Command not found; type ? for a command listing
!ad81009000g200270m:ASCA >
!ad81009000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000g200270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000g200270m:ASCA > read events ad81009000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000g200270m:ASCA-GIS2-PH > set image sky
!ad81009000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad81009000g200270m:ASCA-GIS2-PH > extract image
!ad81009000g200270m:ASCA-GIS2-PH > save image outfile=ad81009000g200270m.img
Wrote image to file ad81009000g200270m.img
!ad81009000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad81009000g200270m:ASCA-GIS2-PH > extract image
!ad81009000g200270m:ASCA-GIS2-PH > save image outfile=ad81009000g200270m_lo.img
Wrote image to file ad81009000g200270m_lo.img
!ad81009000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad81009000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad81009000g200270m:ASCA-GIS2-PH > extract image
!ad81009000g200270m:ASCA-GIS2-PH > save image outfile=ad81009000g200270m_hi.img
Wrote image to file ad81009000g200270m_hi.img
!ad81009000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad81009000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad81009000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7900
Mean RA/DEC/ROLL : 112.6893 31.4125 259.7900
Pnt RA/DEC/ROLL : 112.7302 31.4125 259.7900
Image rebin factor : 1
Attitude Records : 39532
GTI intervals : 2
Total GTI (secs) : 2671.867
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 408.3737488 408.3737488
20 Percent Complete: Total/live time: 668.3729248 668.3729248
30 Percent Complete: Total/live time: 1106.3715820 1106.3715820
40 Percent Complete: Total/live time: 1106.3715820 1106.3715820
50 Percent Complete: Total/live time: 1583.3701172 1583.3701172
60 Percent Complete: Total/live time: 2080.8684082 2080.8684082
70 Percent Complete: Total/live time: 2080.8684082 2080.8684082
80 Percent Complete: Total/live time: 2607.8666992 2607.8666992
90 Percent Complete: Total/live time: 2607.8666992 2607.8666992
100 Percent Complete: Total/live time: 2671.8666992 2671.8666992
Number of attitude steps used: 19
Number of attitude steps avail: 5350
Mean RA/DEC pixel offset: 1.5285 -0.9570
writing expo file: ad81009000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 691 17 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
708 691 17 0 0 0
in 2671.87 seconds
Image has 691 counts for 0.2586 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 310 17 0 0 381
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
708 310 17 0 0 381
in 2671.87 seconds
Image has 310 counts for 0.1160 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 382 17 0 0 309
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
708 382 17 0 0 309
in 2671.87 seconds
Image has 382 counts for 0.1430 counts/sec
Command not found; type ? for a command listing
!ad81009000g300170h:ASCA >
!ad81009000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000g300170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000g300170h:ASCA > read events ad81009000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000g300170h:ASCA-GIS3-PH > set image sky
!ad81009000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad81009000g300170h:ASCA-GIS3-PH > extract image
!ad81009000g300170h:ASCA-GIS3-PH > save image outfile=ad81009000g300170h.img
Wrote image to file ad81009000g300170h.img
!ad81009000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad81009000g300170h:ASCA-GIS3-PH > extract image
!ad81009000g300170h:ASCA-GIS3-PH > save image outfile=ad81009000g300170h_lo.img
Wrote image to file ad81009000g300170h_lo.img
!ad81009000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad81009000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad81009000g300170h:ASCA-GIS3-PH > extract image
!ad81009000g300170h:ASCA-GIS3-PH > save image outfile=ad81009000g300170h_hi.img
Wrote image to file ad81009000g300170h_hi.img
!ad81009000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad81009000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad81009000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7817
Mean RA/DEC/ROLL : 112.6751 31.4291 259.7817
Pnt RA/DEC/ROLL : 112.6492 31.2678 259.7817
Image rebin factor : 1
Attitude Records : 39532
GTI intervals : 2
Total GTI (secs) : 1072.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 143.9995880 143.9995880
20 Percent Complete: Total/live time: 282.8580933 282.8580933
30 Percent Complete: Total/live time: 394.8578796 394.8578796
40 Percent Complete: Total/live time: 486.8575439 486.8575439
50 Percent Complete: Total/live time: 570.8572388 570.8572388
60 Percent Complete: Total/live time: 666.8568115 666.8568115
70 Percent Complete: Total/live time: 838.8562622 838.8562622
80 Percent Complete: Total/live time: 986.8558350 986.8558350
90 Percent Complete: Total/live time: 986.8558350 986.8558350
100 Percent Complete: Total/live time: 1071.9995117 1071.9995117
Number of attitude steps used: 20
Number of attitude steps avail: 415
Mean RA/DEC pixel offset: 1.0834 -0.0502
writing expo file: ad81009000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 300 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 292 8 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
300 292 8 0 0 0
in 1072.00 seconds
Image has 292 counts for 0.2724 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 134 8 0 0 158
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
300 134 8 0 0 158
in 1072.00 seconds
Image has 134 counts for 0.1250 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 159 8 0 0 133
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
300 159 8 0 0 133
in 1072.00 seconds
Image has 159 counts for 0.1483 counts/sec
Command not found; type ? for a command listing
!ad81009000g300270m:ASCA >
!ad81009000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000g300270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000g300270m:ASCA > read events ad81009000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000g300270m:ASCA-GIS3-PH > set image sky
!ad81009000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad81009000g300270m:ASCA-GIS3-PH > extract image
!ad81009000g300270m:ASCA-GIS3-PH > save image outfile=ad81009000g300270m.img
Wrote image to file ad81009000g300270m.img
!ad81009000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad81009000g300270m:ASCA-GIS3-PH > extract image
!ad81009000g300270m:ASCA-GIS3-PH > save image outfile=ad81009000g300270m_lo.img
Wrote image to file ad81009000g300270m_lo.img
!ad81009000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad81009000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad81009000g300270m:ASCA-GIS3-PH > extract image
!ad81009000g300270m:ASCA-GIS3-PH > save image outfile=ad81009000g300270m_hi.img
Wrote image to file ad81009000g300270m_hi.img
!ad81009000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad81009000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad81009000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7787
Mean RA/DEC/ROLL : 112.6599 31.3984 259.7787
Pnt RA/DEC/ROLL : 112.7530 31.4225 259.7787
Image rebin factor : 4
Attitude Records : 39532
Hot Pixels : 599
GTI intervals : 6
Total GTI (secs) : 2137.824
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 293.8742371 293.8742371
20 Percent Complete: Total/live time: 668.3729248 668.3729248
30 Percent Complete: Total/live time: 668.3729248 668.3729248
40 Percent Complete: Total/live time: 1023.9999390 1023.9999390
50 Percent Complete: Total/live time: 1455.3701172 1455.3701172
60 Percent Complete: Total/live time: 1455.3701172 1455.3701172
70 Percent Complete: Total/live time: 1920.8684082 1920.8684082
80 Percent Complete: Total/live time: 1920.8684082 1920.8684082
90 Percent Complete: Total/live time: 2080.0000000 2080.0000000
100 Percent Complete: Total/live time: 2137.8242188 2137.8242188
Number of attitude steps used: 19
Number of attitude steps avail: 5307
Mean RA/DEC pixel offset: -38.6497 -79.8556
writing expo file: ad81009000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 834 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
834 834 0 0 0 0
in 2137.82 seconds
Image has 834 counts for 0.3901 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 622 0 0 0 212
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
834 622 0 0 0 212
in 2137.82 seconds
Image has 622 counts for 0.2910 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 212 0 0 0 622
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
834 212 0 0 0 622
in 2137.82 seconds
Image has 212 counts for 9.9166E-02 counts/sec
Command not found; type ? for a command listing
!ad81009000s000102h:ASCA >
!ad81009000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000s000102h:ASCA > read events ad81009000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad81009000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad81009000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000102h.img
Wrote image to file ad81009000s000102h.img
!ad81009000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad81009000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000102h_lo.img
Wrote image to file ad81009000s000102h_lo.img
!ad81009000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad81009000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad81009000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000102h_hi.img
Wrote image to file ad81009000s000102h_hi.img
!ad81009000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad81009000s000302m.expo
ASCAEXPO_V0.9b
reading data file: ad81009000s000302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7727
Mean RA/DEC/ROLL : 112.6394 31.3892 259.7727
Pnt RA/DEC/ROLL : 112.6705 31.2671 259.7727
Image rebin factor : 4
Attitude Records : 39532
Hot Pixels : 411
GTI intervals : 4
Total GTI (secs) : 736.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 110.8582611 110.8582611
20 Percent Complete: Total/live time: 170.8579712 170.8579712
30 Percent Complete: Total/live time: 230.8577576 230.8577576
40 Percent Complete: Total/live time: 342.8574829 342.8574829
50 Percent Complete: Total/live time: 386.8573303 386.8573303
60 Percent Complete: Total/live time: 470.8569641 470.8569641
70 Percent Complete: Total/live time: 558.8567505 558.8567505
80 Percent Complete: Total/live time: 622.8565063 622.8565063
90 Percent Complete: Total/live time: 682.8563232 682.8563232
100 Percent Complete: Total/live time: 736.0000610 736.0000610
Number of attitude steps used: 19
Number of attitude steps avail: 214
Mean RA/DEC pixel offset: -45.9111 -76.8501
writing expo file: ad81009000s000302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000s000302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000s000302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.74E+03 365 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 365 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
365 365 0 0 0 0
in 736.00 seconds
Image has 365 counts for 0.4959 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 299 0 0 0 66
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
365 299 0 0 0 66
in 736.00 seconds
Image has 299 counts for 0.4062 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 66 0 0 0 299
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
365 66 0 0 0 299
in 736.00 seconds
Image has 66 counts for 8.9674E-02 counts/sec
Command not found; type ? for a command listing
!ad81009000s000302m:ASCA >
!ad81009000s000302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000s000302m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000s000302m:ASCA > read events ad81009000s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad81009000s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad81009000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000302m.img
Wrote image to file ad81009000s000302m.img
!ad81009000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad81009000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000302m_lo.img
Wrote image to file ad81009000s000302m_lo.img
!ad81009000s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad81009000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad81009000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad81009000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad81009000s000302m_hi.img
Wrote image to file ad81009000s000302m_hi.img
!ad81009000s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad81009000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad81009000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7881
Mean RA/DEC/ROLL : 112.6831 31.3984 259.7881
Pnt RA/DEC/ROLL : 112.7349 31.4263 259.7881
Image rebin factor : 4
Attitude Records : 39532
Hot Pixels : 868
GTI intervals : 6
Total GTI (secs) : 2425.824
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 293.8742371 293.8742371
20 Percent Complete: Total/live time: 668.3729248 668.3729248
30 Percent Complete: Total/live time: 1023.9999390 1023.9999390
40 Percent Complete: Total/live time: 1023.9999390 1023.9999390
50 Percent Complete: Total/live time: 1423.3701172 1423.3701172
60 Percent Complete: Total/live time: 1888.8684082 1888.8684082
70 Percent Complete: Total/live time: 1888.8684082 1888.8684082
80 Percent Complete: Total/live time: 2368.0000000 2368.0000000
90 Percent Complete: Total/live time: 2368.0000000 2368.0000000
100 Percent Complete: Total/live time: 2425.8242188 2425.8242188
Number of attitude steps used: 19
Number of attitude steps avail: 5307
Mean RA/DEC pixel offset: -42.8601 -11.7861
writing expo file: ad81009000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 1073 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1073 1073 0 0 0 0
in 2425.82 seconds
Image has 1073 counts for 0.4423 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 797 0 0 0 276
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1073 797 0 0 0 276
in 2425.82 seconds
Image has 797 counts for 0.3285 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 276 0 0 0 797
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1073 276 0 0 0 797
in 2425.82 seconds
Image has 276 counts for 0.1138 counts/sec
Command not found; type ? for a command listing
!ad81009000s100102h:ASCA >
!ad81009000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000s100102h:ASCA > read events ad81009000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad81009000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad81009000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100102h.img
Wrote image to file ad81009000s100102h.img
!ad81009000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad81009000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100102h_lo.img
Wrote image to file ad81009000s100102h_lo.img
!ad81009000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad81009000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad81009000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100102h_hi.img
Wrote image to file ad81009000s100102h_hi.img
!ad81009000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad81009000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad81009000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa931102_0609.1958
making an exposure map...
Aspect RA/DEC/ROLL : 112.6170 31.3580 259.7798
Mean RA/DEC/ROLL : 112.6585 31.3861 259.7798
Pnt RA/DEC/ROLL : 112.6530 31.2817 259.7798
Image rebin factor : 4
Attitude Records : 39532
Hot Pixels : 605
GTI intervals : 1
Total GTI (secs) : 800.000
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 110.8582611 110.8582611
20 Percent Complete: Total/live time: 202.8579712 202.8579712
30 Percent Complete: Total/live time: 294.8577576 294.8577576
40 Percent Complete: Total/live time: 354.8575134 354.8575134
50 Percent Complete: Total/live time: 450.8573303 450.8573303
60 Percent Complete: Total/live time: 534.8569336 534.8569336
70 Percent Complete: Total/live time: 622.8567505 622.8567505
80 Percent Complete: Total/live time: 686.8565063 686.8565063
90 Percent Complete: Total/live time: 746.8563232 746.8563232
100 Percent Complete: Total/live time: 800.0000000 800.0000000
Number of attitude steps used: 19
Number of attitude steps avail: 205
Mean RA/DEC pixel offset: -50.5929 -9.2218
writing expo file: ad81009000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad81009000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad81009000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.80E+03 540 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 540 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
540 540 0 0 0 0
in 800.00 seconds
Image has 540 counts for 0.6750 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 475 0 0 0 65
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
540 475 0 0 0 65
in 800.00 seconds
Image has 475 counts for 0.5938 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 65 0 0 0 475
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
540 65 0 0 0 475
in 800.00 seconds
Image has 65 counts for 8.1250E-02 counts/sec
Command not found; type ? for a command listing
!ad81009000s100202m:ASCA >
!ad81009000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad81009000s100202m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!ad81009000s100202m:ASCA > read events ad81009000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!ad81009000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad81009000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad81009000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100202m.img
Wrote image to file ad81009000s100202m.img
!ad81009000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad81009000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100202m_lo.img
Wrote image to file ad81009000s100202m_lo.img
!ad81009000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad81009000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad81009000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad81009000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad81009000s100202m_hi.img
Wrote image to file ad81009000s100202m_hi.img
!ad81009000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad81009000s000102h.expo ad81009000s000302m.expo ad81009000s100102h.expo ad81009000s100202m.expo-> Summing the following images to produce ad81009000sis32002_all.totsky
ad81009000s000102h.img ad81009000s000302m.img ad81009000s100102h.img ad81009000s100202m.img-> Summing the following images to produce ad81009000sis32002_lo.totsky
ad81009000s000102h_lo.img ad81009000s000302m_lo.img ad81009000s100102h_lo.img ad81009000s100202m_lo.img-> Summing the following images to produce ad81009000sis32002_hi.totsky
ad81009000s000102h_hi.img ad81009000s000302m_hi.img ad81009000s100102h_hi.img ad81009000s100202m_hi.img-> Running XIMAGE to create ad81009000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad81009000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad81009000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 101.6608 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 101 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 2032 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 19.0000 19 0 ![9]XIMAGE> exit-> Summing gis images
ad81009000g200170h.expo ad81009000g200270m.expo ad81009000g300170h.expo ad81009000g300270m.expo-> Summing the following images to produce ad81009000gis25670_all.totsky
ad81009000g200170h.img ad81009000g200270m.img ad81009000g300170h.img ad81009000g300270m.img-> Summing the following images to produce ad81009000gis25670_lo.totsky
ad81009000g200170h_lo.img ad81009000g200270m_lo.img ad81009000g300170h_lo.img ad81009000g300270m_lo.img-> Summing the following images to produce ad81009000gis25670_hi.totsky
ad81009000g200170h_hi.img ad81009000g200270m_hi.img ad81009000g300170h_hi.img ad81009000g300270m_hi.img-> Running XIMAGE to create ad81009000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad81009000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 3.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 3 min: 0 ![2]XIMAGE> read/exp_map ad81009000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 124.796 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 124 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 2495 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 35.0000 35 0 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad81009000gis25670.src
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad81009000sis32002.src
1 ad81009000s000102h.evt 1199 1 ad81009000s000302m.evt 1199-> Fetching SIS0_OFFCHIP.1
ad81009000s000102h.evt ad81009000s000302m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
2 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.74E+03 365 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 809 25 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 357 8 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1199 1166 33 0 0 0
in 2873.82 seconds
Spectrum has 1166 counts for 0.4057 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2873.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000s010102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 809 25 0 0 0
Writing events file
809 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 357 8 0 0 0
Writing events file
1166 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1199 1166 33 0 0 0
in 2873.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > read events ad81009000s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad81009000s010102_0.pi group=yes
Wrote spectrum to ad81009000s010102_0.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad81009000s010102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2873.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 13 are single channels ... 14 - 21 are grouped by a factor 4 ... 22 - 31 are grouped by a factor 10 ... 32 - 49 are grouped by a factor 9 ... 50 - 61 are grouped by a factor 12 ... 62 - 87 are grouped by a factor 26 ... 88 - 126 are grouped by a factor 39 ... 127 - 174 are grouped by a factor 48 ... 175 - 275 are grouped by a factor 101 ... 276 - 444 are grouped by a factor 169 ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000s010102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:28:50 0.29E+04 1166 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1166 293 873 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1166 293 873 0 0 0
in 2873.82 seconds
Spectrum has 293 counts for 0.1020 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2873.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:28:50 0.29E+04 1166 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1166 261 905 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1166 261 905 0 0 0
in 2873.82 seconds
Spectrum has 261 counts for 9.0820E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2873.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:28:50 0.29E+04 1166 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1166 373 793 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1166 373 793 0 0 0
in 2873.82 seconds
Spectrum has 373 counts for 0.1298 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2873.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:28:50 0.29E+04 1166 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1166 239 927 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1166 239 927 0 0 0
in 2873.82 seconds
Spectrum has 239 counts for 8.3164E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2873.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.251286449399657 rmf1.tmp 0.223842195540309 rmf2.tmp 0.319897084048027 rmf3.tmp 0.204974271012007-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.513E-01 * rmf0.tmp
2.238E-01 * rmf1.tmp
3.199E-01 * rmf2.tmp
2.050E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.22
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.32
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.20
ASCA SIS0 NONE NONE PI
-> Generating ad81009000s010102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.13800E+03
Weighted mean angle from optical axis = 8.798 arcmin
-> Standard Output From STOOL group_event_files:1 ad81009000s000112h.evt 881-> SIS0_OFFCHIP.1 already present in current directory
ad81009000s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 881 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000112h.evt
Total Good Bad: Region Time Phase Cut
881 855 26 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
881 855 26 0 0 0
in 2137.82 seconds
Spectrum has 855 counts for 0.3999 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2137.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000s010212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000112h.evt
Total Good Bad: Region Time Phase Cut
881 855 26 0 0 0
Writing events file
855 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
881 855 26 0 0 0
in 2137.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad81009000s010212_0.pi group=yes
Wrote spectrum to ad81009000s010212_0.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad81009000s010212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2137.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 34 are grouped by a factor 9 ... 35 - 53 are grouped by a factor 19 ... 54 - 76 are grouped by a factor 23 ... 77 - 104 are grouped by a factor 28 ... 105 - 147 are grouped by a factor 43 ... 148 - 218 are grouped by a factor 71 ... 219 - 361 are grouped by a factor 143 ... 362 - 605 are grouped by a factor 244 ... 606 - 913 are grouped by a factor 308 ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000s010212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 855 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
855 208 647 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
855 208 647 0 0 0
in 2137.82 seconds
Spectrum has 208 counts for 9.7295E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2137.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 855 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
855 195 660 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
855 195 660 0 0 0
in 2137.82 seconds
Spectrum has 195 counts for 9.1214E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2137.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 855 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
855 277 578 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
855 277 578 0 0 0
in 2137.82 seconds
Spectrum has 277 counts for 0.1296 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2137.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 855 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
855 175 680 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
855 175 680 0 0 0
in 2137.82 seconds
Spectrum has 175 counts for 8.1859E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2137.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.24327485380117 rmf1.tmp 0.228070175438596 rmf2.tmp 0.323976608187135 rmf3.tmp 0.204678362573099-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.433E-01 * rmf0.tmp
2.281E-01 * rmf1.tmp
3.240E-01 * rmf2.tmp
2.047E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.24
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.23
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.32
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.20
ASCA SIS0 NONE NONE PI
-> Generating ad81009000s010212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.36000E+02
Weighted mean angle from optical axis = 8.879 arcmin
-> Standard Output From STOOL group_event_files:1 ad81009000s100102h.evt 1613 1 ad81009000s100202m.evt 1613-> Fetching SIS1_OFFCHIP.1
ad81009000s100102h.evt ad81009000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
2 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.80E+03 540 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 1049 24 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 525 15 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1613 1574 39 0 0 0
in 3225.82 seconds
Spectrum has 1574 counts for 0.4879 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3225.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000s110102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 1049 24 0 0 0
Writing events file
1049 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 525 15 0 0 0
Writing events file
1574 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1613 1574 39 0 0 0
in 3225.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > read events ad81009000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad81009000s110102_0.pi group=yes
Wrote spectrum to ad81009000s110102_0.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad81009000s110102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3225.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 15 are grouped by a factor 3 ... 16 - 16 are single channels ... 17 - 18 are grouped by a factor 2 ... 19 - 22 are grouped by a factor 4 ... 23 - 31 are grouped by a factor 9 ... 32 - 38 are grouped by a factor 7 ... 39 - 44 are grouped by a factor 6 ... 45 - 52 are grouped by a factor 8 ... 53 - 63 are grouped by a factor 11 ... 64 - 88 are grouped by a factor 25 ... 89 - 125 are grouped by a factor 37 ... 126 - 170 are grouped by a factor 45 ... 171 - 227 are grouped by a factor 57 ... 228 - 360 are grouped by a factor 133 ... 361 - 436 are grouped by a factor 76 ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000s110102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:09:22 0.32E+04 1574 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1574 413 1161 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1574 413 1161 0 0 0
in 3225.82 seconds
Spectrum has 413 counts for 0.1280 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3225.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:09:22 0.32E+04 1574 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1574 393 1181 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1574 393 1181 0 0 0
in 3225.82 seconds
Spectrum has 393 counts for 0.1218 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3225.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:09:22 0.32E+04 1574 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1574 336 1238 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1574 336 1238 0 0 0
in 3225.82 seconds
Spectrum has 336 counts for 0.1042 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3225.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:09:22 0.32E+04 1574 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1574 432 1142 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1574 432 1142 0 0 0
in 3225.82 seconds
Spectrum has 432 counts for 0.1339 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3225.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.262388818297332 rmf1.tmp 0.249682337992376 rmf2.tmp 0.213468869123253 rmf3.tmp 0.274459974587039-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.624E-01 * rmf0.tmp
2.497E-01 * rmf1.tmp
2.135E-01 * rmf2.tmp
2.745E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.26
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.25
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.21
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.27
ASCA SIS1 NONE NONE PI
-> Generating ad81009000s110102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.53400E+03
Weighted mean angle from optical axis = 9.069 arcmin
-> Standard Output From STOOL group_event_files:1 ad81009000s100112h.evt 1110-> SIS1_OFFCHIP.1 already present in current directory
ad81009000s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1110 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100112h.evt
Total Good Bad: Region Time Phase Cut
1110 1084 26 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1110 1084 26 0 0 0
in 2425.82 seconds
Spectrum has 1084 counts for 0.4469 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2425.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000s110212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100112h.evt
Total Good Bad: Region Time Phase Cut
1110 1084 26 0 0 0
Writing events file
1084 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1110 1084 26 0 0 0
in 2425.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad81009000s110212_0.pi group=yes
Wrote spectrum to ad81009000s110212_0.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad81009000s110212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 2425.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 31 are grouped by a factor 6 ... 32 - 35 are grouped by a factor 4 ... 36 - 45 are grouped by a factor 10 ... 46 - 69 are grouped by a factor 24 ... 70 - 85 are grouped by a factor 16 ... 86 - 104 are grouped by a factor 19 ... 105 - 129 are grouped by a factor 25 ... 130 - 208 are grouped by a factor 79 ... 209 - 301 are grouped by a factor 93 ... 302 - 435 are grouped by a factor 134 ... 436 - 751 are grouped by a factor 316 ... 752 - 868 are grouped by a factor 117 ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000s110212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1084 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1084 287 797 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1084 287 797 0 0 0
in 2425.82 seconds
Spectrum has 287 counts for 0.1183 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2425.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1084 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1084 261 823 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1084 261 823 0 0 0
in 2425.82 seconds
Spectrum has 261 counts for 0.1076 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2425.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1084 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1084 247 837 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1084 247 837 0 0 0
in 2425.82 seconds
Spectrum has 247 counts for 0.1018 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2425.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1084 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1084 289 795 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1084 289 795 0 0 0
in 2425.82 seconds
Spectrum has 289 counts for 0.1191 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 2425.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.264760147601476 rmf1.tmp 0.240774907749077 rmf2.tmp 0.227859778597786 rmf3.tmp 0.266605166051661-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.648E-01 * rmf0.tmp
2.408E-01 * rmf1.tmp
2.279E-01 * rmf2.tmp
2.666E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.26
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.24
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.23
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.27
ASCA SIS1 NONE NONE PI
-> Generating ad81009000s110212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.05400E+03
Weighted mean angle from optical axis = 9.161 arcmin
-> Standard Output From STOOL group_event_files:1 ad81009000g200170h.evt 938 1 ad81009000g200270m.evt 938-> GIS2_REGION256.4 already present in current directory
ad81009000g200170h.evt ad81009000g200270m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 268 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 670 0 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
938 938 0 0 0 0
in 3743.87 seconds
Spectrum has 938 counts for 0.2505 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3743.9 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36888 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > read events ad81009000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad81009000g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad81009000g210170_0.pi group=yes
Wrote spectrum to ad81009000g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad81009000g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad81009000g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3743.9 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 are grouped by a factor 32 ... 32 - 50 are grouped by a factor 19 ... 51 - 70 are grouped by a factor 20 ... 71 - 87 are grouped by a factor 17 ... 88 - 99 are grouped by a factor 12 ... 100 - 116 are grouped by a factor 17 ... 117 - 128 are grouped by a factor 12 ... 129 - 156 are grouped by a factor 14 ... 157 - 173 are grouped by a factor 17 ... 174 - 195 are grouped by a factor 22 ... 196 - 226 are grouped by a factor 31 ... 227 - 267 are grouped by a factor 41 ... 268 - 306 are grouped by a factor 39 ... 307 - 344 are grouped by a factor 38 ... 345 - 389 are grouped by a factor 45 ... 390 - 421 are grouped by a factor 32 ... 422 - 483 are grouped by a factor 62 ... 484 - 550 are grouped by a factor 67 ... 551 - 631 are grouped by a factor 81 ... 632 - 725 are grouped by a factor 94 ... 726 - 862 are grouped by a factor 137 ... 863 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000g210170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 9.38000E+02
Weighted mean angle from optical axis = 14.132 arcmin
-> Standard Output From STOOL group_event_files:1 ad81009000g300170h.evt 1008 1 ad81009000g300270m.evt 1008-> GIS3_REGION256.4 already present in current directory
ad81009000g300170h.evt ad81009000g300270m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 300 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 708 0 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 300 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008 1008 0 0 0 0
in 3743.87 seconds
Spectrum has 1008 counts for 0.2692 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3743.9 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36783 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > read events ad81009000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad81009000g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad81009000g310170_0.pi group=yes
Wrote spectrum to ad81009000g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad81009000g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad81009000g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3743.9 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 36 are grouped by a factor 37 ... 37 - 58 are grouped by a factor 22 ... 59 - 75 are grouped by a factor 17 ... 76 - 87 are grouped by a factor 12 ... 88 - 98 are grouped by a factor 11 ... 99 - 116 are grouped by a factor 9 ... 117 - 136 are grouped by a factor 10 ... 137 - 151 are grouped by a factor 15 ... 152 - 168 are grouped by a factor 17 ... 169 - 180 are grouped by a factor 12 ... 181 - 204 are grouped by a factor 24 ... 205 - 239 are grouped by a factor 35 ... 240 - 277 are grouped by a factor 38 ... 278 - 319 are grouped by a factor 42 ... 320 - 354 are grouped by a factor 35 ... 355 - 399 are grouped by a factor 45 ... 400 - 452 are grouped by a factor 53 ... 453 - 507 are grouped by a factor 55 ... 508 - 621 are grouped by a factor 114 ... 622 - 693 are grouped by a factor 72 ... 694 - 801 are grouped by a factor 108 ... 802 - 939 are grouped by a factor 138 ... 940 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad81009000g310170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.00800E+03
Weighted mean angle from optical axis = 14.346 arcmin
-> Plotting ad81009000g210170_0_pi.ps from ad81009000g210170_0.pi
XSPEC 9.01 12:50:20 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000g210170_0.pi
Net count rate (cts/s) for file 1 0.2505 +/- 8.7413E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad81009000g310170_0_pi.ps from ad81009000g310170_0.pi
XSPEC 9.01 12:50:33 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000g310170_0.pi
Net count rate (cts/s) for file 1 0.2692 +/- 8.7413E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad81009000s010102_0_pi.ps from ad81009000s010102_0.pi
XSPEC 9.01 12:50:47 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000s010102_0.pi
Net count rate (cts/s) for file 1 0.4057 +/- 1.1933E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad81009000s010212_0_pi.ps from ad81009000s010212_0.pi
XSPEC 9.01 12:51:00 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000s010212_0.pi
Net count rate (cts/s) for file 1 0.3999 +/- 1.3829E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad81009000s110102_0_pi.ps from ad81009000s110102_0.pi
XSPEC 9.01 12:51:16 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000s110102_0.pi
Net count rate (cts/s) for file 1 0.4879 +/- 1.2338E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad81009000s110212_0_pi.ps from ad81009000s110212_0.pi
XSPEC 9.01 12:51:30 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad81009000s110212_0.pi
Net count rate (cts/s) for file 1 0.4469 +/- 1.3691E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
2 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.74E+03 365 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 834 0 0 0 0
Writing events file
834 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 365 0 0 0 0
Writing events file
1199 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1199 1199 0 0 0 0
in 2873.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > read events ad81009000s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad81009000s000002_0.lc with binsize 119.842540565179
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:28:50 0.29E+04 1199 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1199 1199 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1199 1199 0 0 0 0
in 2873.82 seconds
Fits light curve has 1199 counts for 0.4172 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > set binsize 119.842540565179
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad81009000s000002_0.lc
Wrote FITS light curve to file ad81009000s000002_0.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad81009000s000002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad81009000s000002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A586 Start Time (d) .... 9293 16:28:50.834
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9293 18:12:44.658
No. of Rows ....... 26 Bin Time (s) ...... 119.8
Right Ascension ... 1.1262E+02 Internal time sys.. Converted to TJD
Declination ....... 3.1358E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 53 Newbins of 119.843 (s)
Intv 1 Start 9293 16:29:50
Ser.1 Avg 0.4307 Chisq 521.6 Var 0.8426E-01 Newbs. 26
Min 0.2003 Max 1.698 expVar 0.4200E-02 Bins 26
Results from Statistical Analysis
Newbin Integration Time (s).. 119.84
Interval Duration (s)........ 5872.3
No. of Newbins .............. 26
Average (c/s) ............... 0.43067 +/- 0.13E-01
Standard Deviation (c/s)..... 0.29027
Minimum (c/s)................ 0.20026
Maximum (c/s)................ 1.6979
Variance ((c/s)**2).......... 0.84256E-01 +/- 0.24E-01
Expected Variance ((c/s)**2). 0.42001E-02 +/- 0.12E-02
Third Moment ((c/s)**3)...... 0.76859E-01
Average Deviation (c/s)...... 0.18285
Skewness..................... 3.1426 +/- 0.48
Kurtosis..................... 11.086 +/- 0.96
RMS fractional variation..... 0.65699 +/- 0.98E-01
Chi-Square................... 521.58 dof 25
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 53 Newbins of 119.843 (s)
Intv 1 Start 9293 16:29:50
Ser.1 Avg 0.4307 Chisq 521.6 Var 0.8426E-01 Newbs. 26
Min 0.2003 Max 1.698 expVar 0.4200E-02 Bins 26
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=1.6000000000E+01 for ad81009000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
2 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.80E+03 540 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 1073 0 0 0 0
Writing events file
1073 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 540 0 0 0 0
Writing events file
1613 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1613 1613 0 0 0 0
in 3225.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > read events ad81009000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad81009000s100002_0.lc with binsize 99.9945479374141
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:09:22 0.32E+04 1613 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1613 1613 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1613 1613 0 0 0 0
in 3225.82 seconds
Fits light curve has 1613 counts for 0.5000 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > set binsize 99.9945479374141
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad81009000s100002_0.lc
Wrote FITS light curve to file ad81009000s100002_0.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad81009000s100002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad81009000s100002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A586 Start Time (d) .... 9293 16:28:50.834
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9293 18:12:44.658
No. of Rows ....... 33 Bin Time (s) ...... 99.99
Right Ascension ... 1.1262E+02 Internal time sys.. Converted to TJD
Declination ....... 3.1358E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 63 Newbins of 99.9945 (s)
Intv 1 Start 9293 16:29:40
Ser.1 Avg 0.5185 Chisq 571.9 Var 0.1003 Newbs. 33
Min 0.1900 Max 1.912 expVar 0.5790E-02 Bins 33
Results from Statistical Analysis
Newbin Integration Time (s).. 99.995
Interval Duration (s)........ 5899.7
No. of Newbins .............. 33
Average (c/s) ............... 0.51846 +/- 0.13E-01
Standard Deviation (c/s)..... 0.31676
Minimum (c/s)................ 0.19001
Maximum (c/s)................ 1.9123
Variance ((c/s)**2).......... 0.10034 +/- 0.25E-01
Expected Variance ((c/s)**2). 0.57900E-02 +/- 0.14E-02
Third Moment ((c/s)**3)...... 0.82779E-01
Average Deviation (c/s)...... 0.21672
Skewness..................... 2.6045 +/- 0.43
Kurtosis..................... 8.7297 +/- 0.85
RMS fractional variation..... 0.59308 +/- 0.79E-01
Chi-Square................... 571.87 dof 32
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0. (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 63 Newbins of 99.9945 (s)
Intv 1 Start 9293 16:29:40
Ser.1 Avg 0.5185 Chisq 571.9 Var 0.1003 Newbs. 33
Min 0.1900 Max 1.912 expVar 0.5790E-02 Bins 33
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=6.2500000000E-02 for ad81009000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 268 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 670 0 0 0 0
Writing events file
670 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
Writing events file
938 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
938 938 0 0 0 0
in 3743.87 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > read events ad81009000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > filter region ad81009000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad81009000g200070_0.lc with binsize 199.566432451412
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:09:38 0.37E+04 938 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
938 938 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
938 938 0 0 0 0
in 3743.87 seconds
Fits light curve has 938 counts for 0.2505 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > set binsize 199.566432451412
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad81009000g200070_0.lc
Wrote FITS light curve to file ad81009000g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad81009000g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad81009000g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A586 Start Time (d) .... 9293 16:28:50.834
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9293 18:12:58.689
No. of Rows ....... 19 Bin Time (s) ...... 199.6
Right Ascension ... 1.1262E+02 Internal time sys.. Converted to TJD
Declination ....... 3.1358E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 32 Newbins of 199.566 (s)
Intv 1 Start 9293 16:30:30
Ser.1 Avg 0.2503 Chisq 19.96 Var 0.1413E-02 Newbs. 19
Min 0.2004 Max 0.3558 expVar 0.1345E-02 Bins 19
Results from Statistical Analysis
Newbin Integration Time (s).. 199.57
Interval Duration (s)........ 5787.4
No. of Newbins .............. 19
Average (c/s) ............... 0.25028 +/- 0.86E-02
Standard Deviation (c/s)..... 0.37593E-01
Minimum (c/s)................ 0.20043
Maximum (c/s)................ 0.35577
Variance ((c/s)**2).......... 0.14132E-02 +/- 0.47E-03
Expected Variance ((c/s)**2). 0.13455E-02 +/- 0.45E-03
Third Moment ((c/s)**3)...... 0.57718E-04
Average Deviation (c/s)...... 0.28384E-01
Skewness..................... 1.0864 +/- 0.56
Kurtosis..................... 1.0305 +/- 1.1
RMS fractional variation....< 0.16380 (3 sigma)
Chi-Square................... 19.956 dof 18
Chi-Square Prob of constancy. 0.33517 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.56922 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 32 Newbins of 199.566 (s)
Intv 1 Start 9293 16:30:30
Ser.1 Avg 0.2503 Chisq 19.96 Var 0.1413E-02 Newbs. 19
Min 0.2004 Max 0.3558 expVar 0.1345E-02 Bins 19
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad81009000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 300 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 708 0 0 0 0
Writing events file
708 events written to the output file
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 300 0 0 0 0
Writing events file
1008 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008 1008 0 0 0 0
in 3743.87 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > read events ad81009000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > filter region ad81009000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad81009000g300070_0.lc with binsize 185.707652420064
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:09:38 0.37E+04 1008 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1008 1008 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1008 1008 0 0 0 0
in 3743.87 seconds
Fits light curve has 1008 counts for 0.2692 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > set binsize 185.707652420064
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad81009000g300070_0.lc
Wrote FITS light curve to file ad81009000g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad81009000g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad81009000g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A586 Start Time (d) .... 9293 16:28:50.834
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9293 18:12:58.689
No. of Rows ....... 20 Bin Time (s) ...... 185.7
Right Ascension ... 1.1262E+02 Internal time sys.. Converted to TJD
Declination ....... 3.1358E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 34 Newbins of 185.708 (s)
Intv 1 Start 9293 16:30:23
Ser.1 Avg 0.2691 Chisq 32.24 Var 0.2437E-02 Newbs. 20
Min 0.1908 Max 0.3877 expVar 0.1512E-02 Bins 20
Results from Statistical Analysis
Newbin Integration Time (s).. 185.71
Interval Duration (s)........ 5756.9
No. of Newbins .............. 20
Average (c/s) ............... 0.26913 +/- 0.89E-02
Standard Deviation (c/s)..... 0.49365E-01
Minimum (c/s)................ 0.19084
Maximum (c/s)................ 0.38771
Variance ((c/s)**2).......... 0.24369E-02 +/- 0.79E-03
Expected Variance ((c/s)**2). 0.15115E-02 +/- 0.49E-03
Third Moment ((c/s)**3)...... 0.43187E-04
Average Deviation (c/s)...... 0.39510E-01
Skewness..................... 0.35899 +/- 0.55
Kurtosis.....................-0.13921 +/- 1.1
RMS fractional variation....< 0.11590 (3 sigma)
Chi-Square................... 32.244 dof 19
Chi-Square Prob of constancy. 0.29334E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.18828E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 34 Newbins of 185.708 (s)
Intv 1 Start 9293 16:30:23
Ser.1 Avg 0.2691 Chisq 32.24 Var 0.2437E-02 Newbs. 20
Min 0.1908 Max 0.3877 expVar 0.1512E-02 Bins 20
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad81009000g200170h.evt[2] ad81009000g200270m.evt[2]-> Making L1 light curve of ft931102_0609_1958G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5410 output records from 5412 good input G2_L1 records.-> Making L1 light curve of ft931102_0609_1958G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3339 output records from 6357 good input G2_L1 records.-> Merging GTIs from the following files:
ad81009000g300170h.evt[2] ad81009000g300270m.evt[2]-> Making L1 light curve of ft931102_0609_1958G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 5143 output records from 5145 good input G3_L1 records.-> Making L1 light curve of ft931102_0609_1958G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3288 output records from 6078 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 670 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.evt
Total Good Bad: Region Time Phase Cut
670 670 0 0 0 0
Writing events file
670 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
670 670 0 0 0 0
in 2671.87 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > filter region ad81009000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad81009000g200170h_0.ulc use_events=yes
Wrote events list to file ad81009000g200170h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad81009000g200270m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 268 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.evt
Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
Writing events file
268 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
268 268 0 0 0 0
in 1072.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > filter region ad81009000g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad81009000g200270m_0.ulc use_events=yes
Wrote events list to file ad81009000g200270m_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad81009000g300170h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.27E+04 708 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.evt
Total Good Bad: Region Time Phase Cut
708 708 0 0 0 0
Writing events file
708 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
708 708 0 0 0 0
in 2671.87 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > filter region ad81009000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad81009000g300170h_0.ulc use_events=yes
Wrote events list to file ad81009000g300170h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad81009000g300270m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.11E+04 300 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.evt
Total Good Bad: Region Time Phase Cut
300 300 0 0 0 0
Writing events file
300 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
300 300 0 0 0 0
in 1072.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > filter region ad81009000g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad81009000g300270m_0.ulc use_events=yes
Wrote events list to file ad81009000g300270m_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad81009000s000102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.21E+04 834 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.evt
Total Good Bad: Region Time Phase Cut
834 834 0 0 0 0
Writing events file
834 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
834 834 0 0 0 0
in 2137.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad81009000s000102h_0.ulc use_events=yes
Wrote events list to file ad81009000s000102h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad81009000s000112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.21E+04 881 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000112h.evt
Total Good Bad: Region Time Phase Cut
881 881 0 0 0 0
Writing events file
881 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
881 881 0 0 0 0
in 2137.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad81009000s000112h_0.ulc use_events=yes
Wrote events list to file ad81009000s000112h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad81009000s000302m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.74E+03 365 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.evt
Total Good Bad: Region Time Phase Cut
365 365 0 0 0 0
Writing events file
365 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
365 365 0 0 0 0
in 736.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad81009000s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad81009000s000302m_0.ulc use_events=yes
Wrote events list to file ad81009000s000302m_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad81009000s100102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.24E+04 1073 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.evt
Total Good Bad: Region Time Phase Cut
1073 1073 0 0 0 0
Writing events file
1073 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1073 1073 0 0 0 0
in 2425.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad81009000s100102h_0.ulc use_events=yes
Wrote events list to file ad81009000s100102h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad81009000s100112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.24E+04 1110 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100112h.evt
Total Good Bad: Region Time Phase Cut
1110 1110 0 0 0 0
Writing events file
1110 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1110 1110 0 0 0 0
in 2425.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad81009000s100112h_0.ulc use_events=yes
Wrote events list to file ad81009000s100112h_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad81009000s100202m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.80E+03 540 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.evt
Total Good Bad: Region Time Phase Cut
540 540 0 0 0 0
Writing events file
540 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
540 540 0 0 0 0
in 800.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad81009000s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad81009000s100202m_0.ulc use_events=yes
Wrote events list to file ad81009000s100202m_0.ulc
Changing Data directory from:
/data/data24/seq_proc/81009000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 10104 Total of 0 sets of frame data are extracted.
1 ad81009000g200170h.unf 27696 1 ad81009000g200270m.unf 27696-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 15247 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 15247 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 12449 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.unf
Total Good Bad: Region Time Phase Cut
15247 5489 9758 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.unf
Total Good Bad: Region Time Phase Cut
12449 3305 9144 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27696 8794 18902 0 0 0
in 26265.91 seconds
Spectrum has 8794 counts for 0.3348 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 26266. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > read events ad81009000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad81009000g220170.cal group=yes
Wrote spectrum to ad81009000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 13:06:07 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad81009000g220170.cal
Net count rate (cts/s) for file 1 0.3348 +/- 3.5717E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 4.3203E+05 using 84 PHA bins.
Reduced chi-squared = 5611.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 4.2826E+05 using 84 PHA bins.
Reduced chi-squared = 5490.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 4.2826E+05 using 84 PHA bins.
Reduced chi-squared = 5421.
!XSPEC> renorm
Chi-Squared = 2678. using 84 PHA bins.
Reduced chi-squared = 33.90
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2117.0 0 1.000 5.893 9.2227E-02 0.1085
9.4695E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
728.15 0 1.000 5.862 0.1439 0.1639
8.2757E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
231.67 -1 1.000 5.899 0.1593 0.2277
5.7928E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
178.60 -2 1.000 5.932 0.1772 0.2516
4.2134E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
178.36 -3 1.000 5.931 0.1755 0.2512
4.2606E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
178.36 -4 1.000 5.931 0.1753 0.2512
4.2573E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93075 +/- 0.54788E-02
3 3 2 gaussian/b Sigma 0.175325 +/- 0.60160E-02
4 4 2 gaussian/b norm 0.251228 +/- 0.38774E-02
5 2 3 gaussian/b LineE 6.52978 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.183966 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.257295E-02 +/- 0.26147E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 178.4 using 84 PHA bins.
Reduced chi-squared = 2.258
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad81009000g220170.cal peaks at 5.93075 +/- 0.0054788 keV1 ad81009000g300170h.unf 25841 1 ad81009000g300270m.unf 25841-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 14240 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 14240 1024
2 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 11601 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.unf
Total Good Bad: Region Time Phase Cut
14240 5065 9175 0 0 0
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.unf
Total Good Bad: Region Time Phase Cut
11601 3027 8574 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25841 8092 17749 0 0 0
in 26239.91 seconds
Spectrum has 8092 counts for 0.3084 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 26240. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad81009000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!xsel:ASCA > read events ad81009000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > read events ad81009000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad81009000g320170.cal group=yes
Wrote spectrum to ad81009000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 13:07:04 23-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad81009000g320170.cal
Net count rate (cts/s) for file 1 0.3084 +/- 3.4348E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 4.5048E+05 using 84 PHA bins.
Reduced chi-squared = 5850.
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 4.4668E+05 using 84 PHA bins.
Reduced chi-squared = 5727.
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 4.4668E+05 using 84 PHA bins.
Reduced chi-squared = 5654.
!XSPEC> renorm
Chi-Squared = 2488. using 84 PHA bins.
Reduced chi-squared = 31.50
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1976.0 0 1.000 5.894 9.1696E-02 0.1041
9.1363E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
873.41 0 1.000 5.874 0.1306 0.1535
7.9186E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
258.86 -1 1.000 5.933 0.1371 0.2147
5.1734E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
157.28 -2 1.000 5.972 0.1510 0.2440
3.5879E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
156.45 -3 1.000 5.971 0.1479 0.2445
3.5746E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
156.44 -4 1.000 5.971 0.1478 0.2445
3.5760E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
156.43 -5 1.000 5.971 0.1477 0.2445
3.5764E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.97060 +/- 0.46708E-02
3 3 2 gaussian/b Sigma 0.147739 +/- 0.57836E-02
4 4 2 gaussian/b norm 0.244533 +/- 0.35652E-02
5 2 3 gaussian/b LineE 6.57366 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.155021 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.576381E-02 +/- 0.21203E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 156.4 using 84 PHA bins.
Reduced chi-squared = 1.980
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad81009000g320170.cal peaks at 5.97060 +/- 0.0046708 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.15E+05 246228 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad81009000s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.15E+05 255477 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad81009000s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT HIGH 02/11/93 07:34:58 0.18E+04 37057 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s000202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad81009000s000202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 07:34:58 0.18E+04 43600 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s000212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad81009000s000212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:28:50 0.72E+04 107481 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000302m.unf
Total Good Bad: Region Time Phase Cut
107481 45329 0 62152 0 0
Writing events file
45329 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
107481 45329 0 62152 0 0
in 3228.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad81009000s000302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad81009000s000302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 45329
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 106 18651
Flickering pixels iter, pixels & cnts : 1 155 1714
cleaning chip # 1
Hot pixels & counts : 53 6596
Flickering pixels iter, pixels & cnts : 1 131 984
cleaning chip # 2
Hot pixels & counts : 57 6840
Flickering pixels iter, pixels & cnts : 1 133 1088
cleaning chip # 3
Hot pixels & counts : 49 7020
Flickering pixels iter, pixels & cnts : 1 124 853
Number of pixels rejected : 808
Number of (internal) image counts : 45329
Number of image cts rejected (N, %) : 43746 96.5077515
By chip : 0 1 2 3
Pixels rejected : 261 184 190 173
Image counts : 20675 7914 8503 8237
Image cts rejected: 20365 7580 7928 7873
Image cts rej (%) : 98.50 95.78 93.24 95.58
filtering data...
Total counts : 20675 7914 8503 8237
Total cts rejected: 20365 7580 7928 7873
Total cts rej (%) : 98.50 95.78 93.24 95.58
Number of clean counts accepted : 1583
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 808
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad81009000s000402m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.38E+04 7538 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s000402m.unf
Total Good Bad: Region Time Phase Cut
7538 1592 0 5946 0 0
Writing events file
1592 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7538 1592 0 5946 0 0
in 89.06 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad81009000s000402m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad81009000s000402m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1592
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 45 135
cleaning chip # 1
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 42 139
cleaning chip # 2
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 32 96
cleaning chip # 3
Hot pixels & counts : 0 0
Flickering pixels iter, pixels & cnts : 1 48 165
Number of pixels rejected : 167
Number of (internal) image counts : 1592
Number of image cts rejected (N, %) : 535 33.6055260
By chip : 0 1 2 3
Pixels rejected : 45 42 32 48
Image counts : 384 412 292 504
Image cts rejected: 135 139 96 165
Image cts rej (%) : 35.16 33.74 32.88 32.74
filtering data...
Total counts : 384 412 292 504
Total cts rejected: 135 139 96 165
Total cts rej (%) : 35.16 33.74 32.88 32.74
Number of clean counts accepted : 1057
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 167
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad81009000s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT HIGH 02/11/93 06:52:58 0.17E+05 357738 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad81009000s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT2 HIGH 02/11/93 06:52:58 0.17E+05 371690 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad81009000s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A586 BRIGHT MEDIUM 02/11/93 06:09:22 0.13E+05 167004 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000s100202m.unf
Total Good Bad: Region Time Phase Cut
167004 59069 0 107935 0 0
Writing events file
59069 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
167004 59069 0 107935 0 0
in 3335.56 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad81009000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad81009000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 59069
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 78 11199
Flickering pixels iter, pixels & cnts : 1 141 1792
cleaning chip # 1
Hot pixels & counts : 89 13455
Flickering pixels iter, pixels & cnts : 1 156 2373
cleaning chip # 2
Hot pixels & counts : 68 10665
Flickering pixels iter, pixels & cnts : 1 91 1136
cleaning chip # 3
Hot pixels & counts : 92 14014
Flickering pixels iter, pixels & cnts : 1 156 2440
Number of pixels rejected : 871
Number of (internal) image counts : 59069
Number of image cts rejected (N, %) : 57074 96.6225967
By chip : 0 1 2 3
Pixels rejected : 219 245 159 248
Image counts : 13592 16478 12101 16898
Image cts rejected: 12991 15828 11801 16454
Image cts rej (%) : 95.58 96.06 97.52 97.37
filtering data...
Total counts : 13592 16478 12101 16898
Total cts rejected: 12991 15828 11801 16454
Total cts rej (%) : 95.58 96.06 97.52 97.37
Number of clean counts accepted : 1995
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 871
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad81009000g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 15247 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad81009000g200170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 15247 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200170h.unf
Total Good Bad: Region Time Phase Cut
15247 498 0 14749 0 0
Writing events file
498 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15247 498 0 14749 0 0
in 253.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad81009000g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 12449 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.unf
Total Good Bad: Region Time Phase Cut
12449 2137 0 10312 0 0
Writing events file
2137 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12449 2137 0 10312 0 0
in 2448.18 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad81009000g200270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 12449 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g200270m.unf
Total Good Bad: Region Time Phase Cut
12449 6678 0 5771 0 0
Writing events file
6678 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12449 6678 0 5771 0 0
in 3120.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad81009000g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 14240 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad81009000g300170h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH HIGH 02/11/93 06:53:12 0.17E+05 14240 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300170h.unf
Total Good Bad: Region Time Phase Cut
14240 479 0 13761 0 0
Writing events file
479 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14240 479 0 13761 0 0
in 253.77 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad81009000g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 11601 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.unf
Total Good Bad: Region Time Phase Cut
11601 1980 0 9621 0 0
Writing events file
1980 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11601 1980 0 9621 0 0
in 2448.18 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad81009000g300270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A586 PH MEDIUM 02/11/93 06:09:38 0.96E+04 11601 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/81009000.006/ad81009000g300270m.unf
Total Good Bad: Region Time Phase Cut
11601 6274 0 5327 0 0
Writing events file
6274 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11601 6274 0 5327 0 0
in 3120.10 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/81009000.006/
Setting mkf directory to /data/data24/seq_proc/81009000.006/
!earthevents:ASCA > read events ad81009000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/81009000.006/
HK Directory is: /data/data24/seq_proc/81009000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad81009000s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad81009000s000202h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad81009000s000102h.unf
ad81009000s000302m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad81009000s000402m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad81009000s000302m.unf
ad81009000s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad81009000s000212h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad81009000s000112h.unf
ad81009000s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad81009000s000201h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad81009000s000101h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files