The following information is also available:
Time column is TIME ORDERED-> Fetching fa950325_0003.1531.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 70243419.626900 70299067.451400
Data file start and stop ascatime : 70243419.626900 70299067.451400
Aspecting run start and stop ascatime : 70243419.627012 70299067.451307
Time interval averaged over (seconds) : 55647.824295
Total pointing and manuver time (sec) : 33978.980469 21668.976562
Mean boresight Euler angles : 213.403250 18.892341 62.619823
RA DEC SUN ANGLE
Mean solar position (deg) : 2.94 1.27
Mean aberration (arcsec) : 50.35 -11.51
Mean sat X-axis (deg) : 277.297867 -8.563710 85.88
Mean sat Y-axis (deg) : 4.706903 16.709428 15.53
Mean sat Z-axis (deg) : 213.403250 71.107658 104.95
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 213.397247 71.391907 332.626434 0.186576
Minimum 213.371689 71.290199 332.001526 0.012455
Maximum 214.023056 71.397034 332.653290 12.752885
Sigma (RMS) 0.006807 0.000451 0.044114 0.898654
Number of ASPECT records processed = 67614
Aspecting to RA/DEC : 213.39724731 71.39190674
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 70246859.115216 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 70253639.592500 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 213.397 DEC: 71.392
START TIME: SC 70243419.6270 = UT 25/03/95 00:03:39
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000091 12.124 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
939.997009 12.139 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
1379.995483 11.023 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1411.995361 9.929 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1443.995239 8.867 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1479.995117 7.863 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1531.994995 6.831 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
1619.994629 5.805 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1683.994507 4.789 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1735.994263 3.751 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1791.994141 2.736 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1863.993774 1.735 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
1995.993286 0.723 2803 1 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
3095.989502 0.275 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
6683.977539 0.494 E02A83 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 0 4
8845.969727 0.167 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
12431.958008 0.225 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
14603.951172 0.048 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
18181.939453 0.129 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
20347.933594 0.027 102443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 0 2
23929.921875 0.119 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
26107.914062 0.037 182443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 0 3
29679.904297 0.129 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
31845.896484 0.112 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
35427.886719 0.111 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
37595.878906 0.056 182443 1 1 0 0 0 0 1 0 0 0 1 0 0 1 0 0 3
41177.867188 0.093 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
43345.863281 0.045 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
46925.851562 0.081 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
49095.843750 0.073 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
52675.832031 0.100 2A03 1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
54845.828125 0.093 2403 1 1 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0
55647.824219 12.753 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
Attitude Records: 67614
Attitude Steps: 33
Maneuver ACM time: 21669.0 sec
Pointed ACM time: 33979.0 sec
-> Calculating aspect point36 96 count=1585 sum1=338204 sum2=29942 sum3=99289.3 37 95 count=42 sum1=8962.14 sum2=793.338 sum3=2630.79 37 96 count=2944 sum1=628212 sum2=55614.8 sum3=184398 38 95 count=18 sum1=3841.2 sum2=340.002 sum3=1127.25 38 96 count=43896 sum1=9.36735e+06 sum2=829310 sum3=2.74895e+06 39 95 count=1793 sum1=382634 sum2=33866.7 sum3=112271 39 96 count=16775 sum1=3.57981e+06 sum2=316917 sum3=1.05047e+06 40 96 count=51 sum1=10884.2 sum2=963.657 sum3=3192.83 41 96 count=5 sum1=1067.11 sum2=94.498 sum3=312.987 41 97 count=13 sum1=2774.54 sum2=245.729 sum3=813.71 42 97 count=13 sum1=2774.65 sum2=245.786 sum3=813.609 42 98 count=1 sum1=213.44 sum2=18.91 sum3=62.58 43 98 count=11 sum1=2347.91 sum2=208.041 sum3=688.316 44 98 count=5 sum1=1067.28 sum2=94.588 sum3=312.827 44 99 count=1 sum1=213.459 sum2=18.92 sum3=62.562 45 99 count=7 sum1=1494.26 sum2=132.459 sum3=437.892 46 99 count=4 sum1=853.896 sum2=75.71 sum3=250.192 46 100 count=2 sum1=426.958 sum2=37.861 sum3=125.086 47 100 count=5 sum1=1067.43 sum2=94.665 sum3=312.683 48 100 count=4 sum1=853.983 sum2=75.75 sum3=250.108 49 101 count=4 sum1=854.018 sum2=75.766 sum3=250.076 50 101 count=5 sum1=1067.58 sum2=94.733 sum3=312.542 51 101 count=2 sum1=427.05 sum2=37.899 sum3=125 51 102 count=1 sum1=213.529 sum2=18.951 sum3=62.496 52 102 count=4 sum1=854.143 sum2=75.818 sum3=249.958 53 102 count=3 sum1=640.638 sum2=56.872 sum3=187.441 54 102 count=1 sum1=213.552 sum2=18.959 sum3=62.475 54 103 count=2 sum1=427.114 sum2=37.921 sum3=124.94 55 103 count=4 sum1=854.263 sum2=75.851 sum3=249.846 56 103 count=3 sum1=640.731 sum2=56.893 sum3=187.354 57 103 count=3 sum1=640.76 sum2=56.897 sum3=187.326 58 103 count=3 sum1=640.791 sum2=56.898 sum3=187.299 59 103 count=3 sum1=640.823 sum2=56.9 sum3=187.268 60 103 count=2 sum1=427.233 sum2=37.934 sum3=124.829 61 103 count=3 sum1=640.876 sum2=56.899 sum3=187.219 62 103 count=3 sum1=640.911 sum2=56.895 sum3=187.186 63 103 count=2 sum1=427.293 sum2=37.928 sum3=124.773 64 103 count=2 sum1=427.31 sum2=37.926 sum3=124.757 65 103 count=3 sum1=640.999 sum2=56.886 sum3=187.103 66 103 count=1 sum1=213.676 sum2=18.961 sum3=62.359 67 103 count=2 sum1=427.367 sum2=37.92 sum3=124.705 68 102 count=2 sum1=427.397 sum2=37.917 sum3=124.675 68 103 count=1 sum1=213.691 sum2=18.96 sum3=62.345 69 102 count=1 sum1=213.707 sum2=18.958 sum3=62.33 70 102 count=2 sum1=427.431 sum2=37.914 sum3=124.644 71 102 count=2 sum1=427.455 sum2=37.912 sum3=124.621 72 102 count=1 sum1=213.736 sum2=18.955 sum3=62.303 73 102 count=2 sum1=427.492 sum2=37.908 sum3=124.589 74 102 count=1 sum1=213.755 sum2=18.953 sum3=62.285 75 102 count=2 sum1=427.532 sum2=37.903 sum3=124.549 76 102 count=1 sum1=213.777 sum2=18.951 sum3=62.265 77 101 count=2 sum1=427.573 sum2=37.9 sum3=124.511 78 101 count=1 sum1=213.798 sum2=18.949 sum3=62.245 79 101 count=1 sum1=213.805 sum2=18.948 sum3=62.239 80 101 count=2 sum1=427.632 sum2=37.893 sum3=124.459 81 101 count=1 sum1=213.828 sum2=18.946 sum3=62.217 82 101 count=1 sum1=213.837 sum2=18.945 sum3=62.209 83 101 count=1 sum1=213.844 sum2=18.944 sum3=62.201 84 101 count=2 sum1=427.711 sum2=37.886 sum3=124.382 85 101 count=1 sum1=213.867 sum2=18.942 sum3=62.181 86 101 count=1 sum1=213.875 sum2=18.941 sum3=62.174 87 101 count=1 sum1=213.883 sum2=18.94 sum3=62.165 88 100 count=1 sum1=213.893 sum2=18.939 sum3=62.156 89 100 count=2 sum1=427.811 sum2=37.876 sum3=124.289 90 100 count=1 sum1=213.916 sum2=18.937 sum3=62.134 91 100 count=2 sum1=427.853 sum2=37.871 sum3=124.25 92 100 count=1 sum1=213.938 sum2=18.935 sum3=62.116 93 100 count=1 sum1=213.947 sum2=18.934 sum3=62.107 94 100 count=1 sum1=213.956 sum2=18.933 sum3=62.097 95 100 count=1 sum1=213.965 sum2=18.932 sum3=62.089 96 100 count=2 sum1=427.948 sum2=37.862 sum3=124.161 96 106 count=1 sum1=213.98 sum2=18.994 sum3=62.191 97 100 count=2 sum1=427.969 sum2=37.86 sum3=124.142 98 99 count=1 sum1=213.992 sum2=18.929 sum3=62.064 99 99 count=1 sum1=214.001 sum2=18.928 sum3=62.056 100 99 count=331 sum1=70840.1 sum2=6264.62 sum3=20534.2 100 100 count=5 sum1=1070.07 sum2=94.65 sum3=310.071 0 out of 67613 points outside bin structure-> Euler angles: 213.4, 18.8924, 62.6231
Interpolating 23 records in time interval 7.02991e+07 - 7.02991e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft950325_0003.1531",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft950325_0003.1531 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 1082368 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 1081344 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 16939 no. of SIS events found = 754214-> Standard Error Output From FTOOL frfread
coordinate error 0 0 coordinate error 192 0 coordinate error 0 0-> Removing the following files with NEVENTS=0
ft950325_0003_1531G200470H.fits ft950325_0003_1531G201070H.fits ft950325_0003_1531G201770M.fits ft950325_0003_1531G201870L.fits ft950325_0003_1531G201970L.fits ft950325_0003_1531G202270H.fits ft950325_0003_1531G202470H.fits ft950325_0003_1531G202670H.fits ft950325_0003_1531G202770M.fits ft950325_0003_1531G202870M.fits ft950325_0003_1531G203570H.fits ft950325_0003_1531G203670M.fits ft950325_0003_1531G203770M.fits ft950325_0003_1531G203870H.fits ft950325_0003_1531G203970H.fits ft950325_0003_1531G204070H.fits ft950325_0003_1531G204170H.fits ft950325_0003_1531G204270H.fits ft950325_0003_1531G204670H.fits ft950325_0003_1531G204770M.fits ft950325_0003_1531G204870M.fits ft950325_0003_1531G204970H.fits ft950325_0003_1531G205070H.fits ft950325_0003_1531G205170H.fits ft950325_0003_1531G205270H.fits ft950325_0003_1531G205370H.fits ft950325_0003_1531G205799.fits ft950325_0003_1531G206070H.fits ft950325_0003_1531G206170H.fits ft950325_0003_1531G206270H.fits ft950325_0003_1531G206699.fits ft950325_0003_1531G206870H.fits ft950325_0003_1531G206970M.fits ft950325_0003_1531G207070H.fits ft950325_0003_1531G207170H.fits ft950325_0003_1531G207599.fits ft950325_0003_1531G207770H.fits ft950325_0003_1531G207870H.fits ft950325_0003_1531G207970H.fits ft950325_0003_1531G208070H.fits ft950325_0003_1531G208470H.fits ft950325_0003_1531G208570M.fits ft950325_0003_1531G208670H.fits ft950325_0003_1531G208770H.fits ft950325_0003_1531G208970H.fits ft950325_0003_1531G209270M.fits ft950325_0003_1531G209370H.fits ft950325_0003_1531G209470H.fits ft950325_0003_1531G209870H.fits ft950325_0003_1531G209970H.fits ft950325_0003_1531G210070H.fits ft950325_0003_1531G210170H.fits ft950325_0003_1531G210370H.fits ft950325_0003_1531G210673H.fits ft950325_0003_1531G300370H.fits ft950325_0003_1531G301070H.fits ft950325_0003_1531G301370H.fits ft950325_0003_1531G302070M.fits ft950325_0003_1531G302170L.fits ft950325_0003_1531G302270L.fits ft950325_0003_1531G302570H.fits ft950325_0003_1531G302970H.fits ft950325_0003_1531G303070H.fits ft950325_0003_1531G303170M.fits ft950325_0003_1531G303270M.fits ft950325_0003_1531G303970H.fits ft950325_0003_1531G304070H.fits ft950325_0003_1531G304170M.fits ft950325_0003_1531G304270M.fits ft950325_0003_1531G304370H.fits ft950325_0003_1531G304470H.fits ft950325_0003_1531G304570H.fits ft950325_0003_1531G304670H.fits ft950325_0003_1531G304870H.fits ft950325_0003_1531G305170H.fits ft950325_0003_1531G305270H.fits ft950325_0003_1531G305370M.fits ft950325_0003_1531G305470M.fits ft950325_0003_1531G305570H.fits ft950325_0003_1531G305670H.fits ft950325_0003_1531G305770H.fits ft950325_0003_1531G305870H.fits ft950325_0003_1531G305970H.fits ft950325_0003_1531G306399.fits ft950325_0003_1531G306770H.fits ft950325_0003_1531G306870H.fits ft950325_0003_1531G306970H.fits ft950325_0003_1531G307399.fits ft950325_0003_1531G307570H.fits ft950325_0003_1531G307670H.fits ft950325_0003_1531G307770M.fits ft950325_0003_1531G307870H.fits ft950325_0003_1531G307970H.fits ft950325_0003_1531G308399.fits ft950325_0003_1531G308570H.fits ft950325_0003_1531G308770H.fits ft950325_0003_1531G308870H.fits ft950325_0003_1531G308970H.fits ft950325_0003_1531G309270H.fits ft950325_0003_1531G309370H.fits ft950325_0003_1531G309470M.fits ft950325_0003_1531G309570H.fits ft950325_0003_1531G309670H.fits ft950325_0003_1531G309770H.fits ft950325_0003_1531G310170M.fits ft950325_0003_1531G310270H.fits ft950325_0003_1531G310970H.fits ft950325_0003_1531G311070H.fits ft950325_0003_1531G311170H.fits ft950325_0003_1531G311270H.fits ft950325_0003_1531G311370H.fits ft950325_0003_1531G311573H.fits ft950325_0003_1531S001301M.fits ft950325_0003_1531S002101M.fits ft950325_0003_1531S002499.fits ft950325_0003_1531S002699.fits ft950325_0003_1531S002901M.fits ft950325_0003_1531S003299.fits ft950325_0003_1531S004299.fits ft950325_0003_1531S101301M.fits ft950325_0003_1531S102101M.fits ft950325_0003_1531S102499.fits ft950325_0003_1531S102699.fits ft950325_0003_1531S102901M.fits ft950325_0003_1531S103299.fits ft950325_0003_1531S104299.fits-> Checking for empty GTI extensions
ft950325_0003_1531S000101M.fits[3] ft950325_0003_1531S000201H.fits[3] ft950325_0003_1531S000301M.fits[3] ft950325_0003_1531S000401H.fits[3] ft950325_0003_1531S000501L.fits[3] ft950325_0003_1531S000601H.fits[3] ft950325_0003_1531S000701M.fits[3] ft950325_0003_1531S000801L.fits[3] ft950325_0003_1531S000901L.fits[3] ft950325_0003_1531S001001L.fits[3] ft950325_0003_1531S001101H.fits[3] ft950325_0003_1531S001201H.fits[3] ft950325_0003_1531S001401M.fits[3] ft950325_0003_1531S001501H.fits[3] ft950325_0003_1531S001601M.fits[3] ft950325_0003_1531S001701M.fits[3] ft950325_0003_1531S001801M.fits[3] ft950325_0003_1531S001901H.fits[3] ft950325_0003_1531S002001M.fits[3] ft950325_0003_1531S002201M.fits[3] ft950325_0003_1531S002301H.fits[3] ft950325_0003_1531S002501H.fits[3] ft950325_0003_1531S002701H.fits[3] ft950325_0003_1531S002801H.fits[3] ft950325_0003_1531S003001M.fits[3] ft950325_0003_1531S003101H.fits[3] ft950325_0003_1531S003301H.fits[3] ft950325_0003_1531S003401M.fits[3] ft950325_0003_1531S003501M.fits[3] ft950325_0003_1531S003601M.fits[3] ft950325_0003_1531S003701H.fits[3] ft950325_0003_1531S003801M.fits[3] ft950325_0003_1531S003901M.fits[3] ft950325_0003_1531S004001M.fits[3] ft950325_0003_1531S004101H.fits[3] ft950325_0003_1531S004301H.fits[3] ft950325_0003_1531S004401M.fits[3]-> Merging GTIs from the following files:
ft950325_0003_1531S100101M.fits[3] ft950325_0003_1531S100201H.fits[3] ft950325_0003_1531S100301M.fits[3] ft950325_0003_1531S100401H.fits[3] ft950325_0003_1531S100501L.fits[3] ft950325_0003_1531S100601H.fits[3] ft950325_0003_1531S100701M.fits[3] ft950325_0003_1531S100801L.fits[3] ft950325_0003_1531S100901L.fits[3] ft950325_0003_1531S101001L.fits[3] ft950325_0003_1531S101101H.fits[3] ft950325_0003_1531S101201H.fits[3] ft950325_0003_1531S101401M.fits[3] ft950325_0003_1531S101501H.fits[3] ft950325_0003_1531S101601M.fits[3] ft950325_0003_1531S101701M.fits[3] ft950325_0003_1531S101801M.fits[3] ft950325_0003_1531S101901H.fits[3] ft950325_0003_1531S102001M.fits[3] ft950325_0003_1531S102201M.fits[3] ft950325_0003_1531S102301H.fits[3] ft950325_0003_1531S102501H.fits[3] ft950325_0003_1531S102701H.fits[3] ft950325_0003_1531S102801H.fits[3] ft950325_0003_1531S103001M.fits[3] ft950325_0003_1531S103101H.fits[3] ft950325_0003_1531S103301H.fits[3] ft950325_0003_1531S103401M.fits[3] ft950325_0003_1531S103501M.fits[3] ft950325_0003_1531S103601M.fits[3] ft950325_0003_1531S103701H.fits[3] ft950325_0003_1531S103801M.fits[3] ft950325_0003_1531S103901M.fits[3] ft950325_0003_1531S104001M.fits[3] ft950325_0003_1531S104101H.fits[3] ft950325_0003_1531S104301H.fits[3] ft950325_0003_1531S104401M.fits[3]-> Merging GTIs from the following files:
ft950325_0003_1531G200170M.fits[3] ft950325_0003_1531G200270H.fits[3] ft950325_0003_1531G200370H.fits[3] ft950325_0003_1531G200570H.fits[3] ft950325_0003_1531G200670M.fits[3] ft950325_0003_1531G200770M.fits[3] ft950325_0003_1531G200870H.fits[3] ft950325_0003_1531G200970H.fits[3] ft950325_0003_1531G201170H.fits[3] ft950325_0003_1531G201270L.fits[3] ft950325_0003_1531G201370H.fits[3] ft950325_0003_1531G201470M.fits[3] ft950325_0003_1531G201570M.fits[3] ft950325_0003_1531G201670M.fits[3] ft950325_0003_1531G202070L.fits[3] ft950325_0003_1531G202170L.fits[3] ft950325_0003_1531G202370H.fits[3] ft950325_0003_1531G202570H.fits[3] ft950325_0003_1531G202970M.fits[3] ft950325_0003_1531G203070M.fits[3] ft950325_0003_1531G203170H.fits[3] ft950325_0003_1531G203270H.fits[3] ft950325_0003_1531G203370H.fits[3] ft950325_0003_1531G203470H.fits[3] ft950325_0003_1531G204370H.fits[3] ft950325_0003_1531G204470H.fits[3] ft950325_0003_1531G204570H.fits[3] ft950325_0003_1531G205470H.fits[3] ft950325_0003_1531G205570H.fits[3] ft950325_0003_1531G205670H.fits[3] ft950325_0003_1531G205870H.fits[3] ft950325_0003_1531G205970H.fits[3] ft950325_0003_1531G206370H.fits[3] ft950325_0003_1531G206470H.fits[3] ft950325_0003_1531G206570H.fits[3] ft950325_0003_1531G206770H.fits[3] ft950325_0003_1531G207270H.fits[3] ft950325_0003_1531G207370H.fits[3] ft950325_0003_1531G207470H.fits[3] ft950325_0003_1531G207670H.fits[3] ft950325_0003_1531G208170H.fits[3] ft950325_0003_1531G208270H.fits[3] ft950325_0003_1531G208370H.fits[3] ft950325_0003_1531G208870H.fits[3] ft950325_0003_1531G209070H.fits[3] ft950325_0003_1531G209170M.fits[3] ft950325_0003_1531G209570H.fits[3] ft950325_0003_1531G209670H.fits[3] ft950325_0003_1531G209770H.fits[3] ft950325_0003_1531G210270H.fits[3] ft950325_0003_1531G210470H.fits[3] ft950325_0003_1531G210570H.fits[3] ft950325_0003_1531G210770H.fits[3] ft950325_0003_1531G210870M.fits[3]-> Merging GTIs from the following files:
ft950325_0003_1531G300170M.fits[3] ft950325_0003_1531G300270H.fits[3] ft950325_0003_1531G300470H.fits[3] ft950325_0003_1531G300570H.fits[3] ft950325_0003_1531G300670M.fits[3] ft950325_0003_1531G300770M.fits[3] ft950325_0003_1531G300870H.fits[3] ft950325_0003_1531G300970H.fits[3] ft950325_0003_1531G301170H.fits[3] ft950325_0003_1531G301270L.fits[3] ft950325_0003_1531G301470H.fits[3] ft950325_0003_1531G301570H.fits[3] ft950325_0003_1531G301670H.fits[3] ft950325_0003_1531G301770M.fits[3] ft950325_0003_1531G301870M.fits[3] ft950325_0003_1531G301970M.fits[3] ft950325_0003_1531G302370L.fits[3] ft950325_0003_1531G302470L.fits[3] ft950325_0003_1531G302670H.fits[3] ft950325_0003_1531G302770H.fits[3] ft950325_0003_1531G302870H.fits[3] ft950325_0003_1531G303370M.fits[3] ft950325_0003_1531G303470M.fits[3] ft950325_0003_1531G303570H.fits[3] ft950325_0003_1531G303670H.fits[3] ft950325_0003_1531G303770H.fits[3] ft950325_0003_1531G303870H.fits[3] ft950325_0003_1531G304770H.fits[3] ft950325_0003_1531G304970H.fits[3] ft950325_0003_1531G305070H.fits[3] ft950325_0003_1531G306070H.fits[3] ft950325_0003_1531G306170H.fits[3] ft950325_0003_1531G306270H.fits[3] ft950325_0003_1531G306470H.fits[3] ft950325_0003_1531G306570H.fits[3] ft950325_0003_1531G306670H.fits[3] ft950325_0003_1531G307070H.fits[3] ft950325_0003_1531G307170H.fits[3] ft950325_0003_1531G307270H.fits[3] ft950325_0003_1531G307470H.fits[3] ft950325_0003_1531G308070H.fits[3] ft950325_0003_1531G308170H.fits[3] ft950325_0003_1531G308270H.fits[3] ft950325_0003_1531G308470H.fits[3] ft950325_0003_1531G308670H.fits[3] ft950325_0003_1531G309070H.fits[3] ft950325_0003_1531G309170H.fits[3] ft950325_0003_1531G309870H.fits[3] ft950325_0003_1531G309970H.fits[3] ft950325_0003_1531G310070M.fits[3] ft950325_0003_1531G310370H.fits[3] ft950325_0003_1531G310470H.fits[3] ft950325_0003_1531G310570H.fits[3] ft950325_0003_1531G310670H.fits[3] ft950325_0003_1531G310770H.fits[3] ft950325_0003_1531G310870H.fits[3] ft950325_0003_1531G311470H.fits[3] ft950325_0003_1531G311670H.fits[3] ft950325_0003_1531G311770M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200370h.prelist merge count = 5 photon cnt = 12 GISSORTSPLIT:LO:g200470h.prelist merge count = 4 photon cnt = 9 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200670h.prelist merge count = 16 photon cnt = 27894 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201570h.prelist merge count = 3 photon cnt = 14 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 2221 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 144 GISSORTSPLIT:LO:g200270l.prelist merge count = 2 photon cnt = 6834 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200270m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g200370m.prelist merge count = 6 photon cnt = 4446 GISSORTSPLIT:LO:g200470m.prelist merge count = 2 photon cnt = 59 GISSORTSPLIT:LO:Total filenames split = 54 GISSORTSPLIT:LO:Total split file cnt = 23 GISSORTSPLIT:LO:End program-> Creating ad83033000g200170h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G200570H.fits 2 -- ft950325_0003_1531G201170H.fits 3 -- ft950325_0003_1531G201370H.fits 4 -- ft950325_0003_1531G202570H.fits 5 -- ft950325_0003_1531G203470H.fits 6 -- ft950325_0003_1531G204570H.fits 7 -- ft950325_0003_1531G205670H.fits 8 -- ft950325_0003_1531G205870H.fits 9 -- ft950325_0003_1531G206570H.fits 10 -- ft950325_0003_1531G206770H.fits 11 -- ft950325_0003_1531G207470H.fits 12 -- ft950325_0003_1531G207670H.fits 13 -- ft950325_0003_1531G208370H.fits 14 -- ft950325_0003_1531G209070H.fits 15 -- ft950325_0003_1531G209770H.fits 16 -- ft950325_0003_1531G210570H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G200570H.fits 2 -- ft950325_0003_1531G201170H.fits 3 -- ft950325_0003_1531G201370H.fits 4 -- ft950325_0003_1531G202570H.fits 5 -- ft950325_0003_1531G203470H.fits 6 -- ft950325_0003_1531G204570H.fits 7 -- ft950325_0003_1531G205670H.fits 8 -- ft950325_0003_1531G205870H.fits 9 -- ft950325_0003_1531G206570H.fits 10 -- ft950325_0003_1531G206770H.fits 11 -- ft950325_0003_1531G207470H.fits 12 -- ft950325_0003_1531G207670H.fits 13 -- ft950325_0003_1531G208370H.fits 14 -- ft950325_0003_1531G209070H.fits 15 -- ft950325_0003_1531G209770H.fits 16 -- ft950325_0003_1531G210570H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000g200270l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G201270L.fits 2 -- ft950325_0003_1531G202170L.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G201270L.fits 2 -- ft950325_0003_1531G202170L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000g200370m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G200170M.fits 2 -- ft950325_0003_1531G200770M.fits 3 -- ft950325_0003_1531G201570M.fits 4 -- ft950325_0003_1531G203070M.fits 5 -- ft950325_0003_1531G209170M.fits 6 -- ft950325_0003_1531G210870M.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G200170M.fits 2 -- ft950325_0003_1531G200770M.fits 3 -- ft950325_0003_1531G201570M.fits 4 -- ft950325_0003_1531G203070M.fits 5 -- ft950325_0003_1531G209170M.fits 6 -- ft950325_0003_1531G210870M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft950325_0003_1531G210770H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G210770H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G210770H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000144 events
ft950325_0003_1531G202070L.fits-> Ignoring the following files containing 000000059 events
ft950325_0003_1531G200670M.fits ft950325_0003_1531G201470M.fits-> Ignoring the following files containing 000000014 events
ft950325_0003_1531G206470H.fits ft950325_0003_1531G208270H.fits ft950325_0003_1531G210470H.fits-> Ignoring the following files containing 000000012 events
ft950325_0003_1531G204370H.fits ft950325_0003_1531G205470H.fits ft950325_0003_1531G207270H.fits ft950325_0003_1531G208870H.fits ft950325_0003_1531G209570H.fits-> Ignoring the following files containing 000000011 events
ft950325_0003_1531G203370H.fits-> Ignoring the following files containing 000000011 events
ft950325_0003_1531G202970M.fits-> Ignoring the following files containing 000000009 events
ft950325_0003_1531G204470H.fits ft950325_0003_1531G205570H.fits ft950325_0003_1531G207370H.fits ft950325_0003_1531G209670H.fits-> Ignoring the following files containing 000000006 events
ft950325_0003_1531G203170H.fits-> Ignoring the following files containing 000000005 events
ft950325_0003_1531G203270H.fits-> Ignoring the following files containing 000000005 events
ft950325_0003_1531G201670M.fits-> Ignoring the following files containing 000000002 events
ft950325_0003_1531G200870H.fits-> Ignoring the following files containing 000000002 events
ft950325_0003_1531G206370H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G208170H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G200970H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G200370H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G200270H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G202370H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G205970H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G210270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g300370h.prelist merge count = 3 photon cnt = 8 GISSORTSPLIT:LO:g300470h.prelist merge count = 5 photon cnt = 26 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300770h.prelist merge count = 17 photon cnt = 27484 GISSORTSPLIT:LO:g300870h.prelist merge count = 3 photon cnt = 8 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301870h.prelist merge count = 3 photon cnt = 26 GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 2049 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 139 GISSORTSPLIT:LO:g300270l.prelist merge count = 2 photon cnt = 6820 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300270m.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300370m.prelist merge count = 6 photon cnt = 4167 GISSORTSPLIT:LO:g300470m.prelist merge count = 2 photon cnt = 43 GISSORTSPLIT:LO:Total filenames split = 59 GISSORTSPLIT:LO:Total split file cnt = 25 GISSORTSPLIT:LO:End program-> Creating ad83033000g300170h.unf
---- cmerge: version 1.5 ---- A total of 17 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G300570H.fits 2 -- ft950325_0003_1531G301170H.fits 3 -- ft950325_0003_1531G301470H.fits 4 -- ft950325_0003_1531G301670H.fits 5 -- ft950325_0003_1531G302870H.fits 6 -- ft950325_0003_1531G303870H.fits 7 -- ft950325_0003_1531G305070H.fits 8 -- ft950325_0003_1531G306270H.fits 9 -- ft950325_0003_1531G306470H.fits 10 -- ft950325_0003_1531G307270H.fits 11 -- ft950325_0003_1531G307470H.fits 12 -- ft950325_0003_1531G308270H.fits 13 -- ft950325_0003_1531G308470H.fits 14 -- ft950325_0003_1531G309170H.fits 15 -- ft950325_0003_1531G309970H.fits 16 -- ft950325_0003_1531G310670H.fits 17 -- ft950325_0003_1531G311470H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G300570H.fits 2 -- ft950325_0003_1531G301170H.fits 3 -- ft950325_0003_1531G301470H.fits 4 -- ft950325_0003_1531G301670H.fits 5 -- ft950325_0003_1531G302870H.fits 6 -- ft950325_0003_1531G303870H.fits 7 -- ft950325_0003_1531G305070H.fits 8 -- ft950325_0003_1531G306270H.fits 9 -- ft950325_0003_1531G306470H.fits 10 -- ft950325_0003_1531G307270H.fits 11 -- ft950325_0003_1531G307470H.fits 12 -- ft950325_0003_1531G308270H.fits 13 -- ft950325_0003_1531G308470H.fits 14 -- ft950325_0003_1531G309170H.fits 15 -- ft950325_0003_1531G309970H.fits 16 -- ft950325_0003_1531G310670H.fits 17 -- ft950325_0003_1531G311470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000g300270l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G301270L.fits 2 -- ft950325_0003_1531G302470L.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G301270L.fits 2 -- ft950325_0003_1531G302470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000g300370m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G300170M.fits 2 -- ft950325_0003_1531G300770M.fits 3 -- ft950325_0003_1531G301870M.fits 4 -- ft950325_0003_1531G303470M.fits 5 -- ft950325_0003_1531G310070M.fits 6 -- ft950325_0003_1531G311770M.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G300170M.fits 2 -- ft950325_0003_1531G300770M.fits 3 -- ft950325_0003_1531G301870M.fits 4 -- ft950325_0003_1531G303470M.fits 5 -- ft950325_0003_1531G310070M.fits 6 -- ft950325_0003_1531G311770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft950325_0003_1531G311670H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531G311670H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531G311670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000139 events
ft950325_0003_1531G302370L.fits-> Ignoring the following files containing 000000043 events
ft950325_0003_1531G300670M.fits ft950325_0003_1531G301770M.fits-> Ignoring the following files containing 000000026 events
ft950325_0003_1531G306670H.fits ft950325_0003_1531G308670H.fits ft950325_0003_1531G310770H.fits-> Ignoring the following files containing 000000026 events
ft950325_0003_1531G304970H.fits ft950325_0003_1531G306170H.fits ft950325_0003_1531G308170H.fits ft950325_0003_1531G309870H.fits ft950325_0003_1531G310570H.fits-> Ignoring the following files containing 000000008 events
ft950325_0003_1531G300470H.fits ft950325_0003_1531G302770H.fits ft950325_0003_1531G303770H.fits-> Ignoring the following files containing 000000008 events
ft950325_0003_1531G306070H.fits ft950325_0003_1531G308070H.fits ft950325_0003_1531G310470H.fits-> Ignoring the following files containing 000000007 events
ft950325_0003_1531G303570H.fits-> Ignoring the following files containing 000000007 events
ft950325_0003_1531G301970M.fits-> Ignoring the following files containing 000000006 events
ft950325_0003_1531G303670H.fits-> Ignoring the following files containing 000000004 events
ft950325_0003_1531G303370M.fits-> Ignoring the following files containing 000000003 events
ft950325_0003_1531G309070H.fits-> Ignoring the following files containing 000000003 events
ft950325_0003_1531G307170H.fits-> Ignoring the following files containing 000000003 events
ft950325_0003_1531G304770H.fits ft950325_0003_1531G310370H.fits-> Ignoring the following files containing 000000002 events
ft950325_0003_1531G310870H.fits-> Ignoring the following files containing 000000002 events
ft950325_0003_1531G306570H.fits-> Ignoring the following files containing 000000002 events
ft950325_0003_1531G307070H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G301570H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G300970H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G300870H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G300270H.fits-> Ignoring the following files containing 000000001 events
ft950325_0003_1531G302670H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 14 photon cnt = 322099 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 2 photon cnt = 367 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 3 photon cnt = 5659 SIS0SORTSPLIT:LO:s000401l.prelist merge count = 1 photon cnt = 16 SIS0SORTSPLIT:LO:s000501m.prelist merge count = 14 photon cnt = 21845 SIS0SORTSPLIT:LO:s000601m.prelist merge count = 3 photon cnt = 96 SIS0SORTSPLIT:LO:Total filenames split = 37 SIS0SORTSPLIT:LO:Total split file cnt = 6 SIS0SORTSPLIT:LO:End program-> Creating ad83033000s000101h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S000201H.fits 2 -- ft950325_0003_1531S000401H.fits 3 -- ft950325_0003_1531S000601H.fits 4 -- ft950325_0003_1531S001101H.fits 5 -- ft950325_0003_1531S001501H.fits 6 -- ft950325_0003_1531S001901H.fits 7 -- ft950325_0003_1531S002301H.fits 8 -- ft950325_0003_1531S002501H.fits 9 -- ft950325_0003_1531S002701H.fits 10 -- ft950325_0003_1531S003101H.fits 11 -- ft950325_0003_1531S003301H.fits 12 -- ft950325_0003_1531S003701H.fits 13 -- ft950325_0003_1531S004101H.fits 14 -- ft950325_0003_1531S004301H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S000201H.fits 2 -- ft950325_0003_1531S000401H.fits 3 -- ft950325_0003_1531S000601H.fits 4 -- ft950325_0003_1531S001101H.fits 5 -- ft950325_0003_1531S001501H.fits 6 -- ft950325_0003_1531S001901H.fits 7 -- ft950325_0003_1531S002301H.fits 8 -- ft950325_0003_1531S002501H.fits 9 -- ft950325_0003_1531S002701H.fits 10 -- ft950325_0003_1531S003101H.fits 11 -- ft950325_0003_1531S003301H.fits 12 -- ft950325_0003_1531S003701H.fits 13 -- ft950325_0003_1531S004101H.fits 14 -- ft950325_0003_1531S004301H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000s000201m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S000101M.fits 2 -- ft950325_0003_1531S000301M.fits 3 -- ft950325_0003_1531S000701M.fits 4 -- ft950325_0003_1531S001401M.fits 5 -- ft950325_0003_1531S001601M.fits 6 -- ft950325_0003_1531S001801M.fits 7 -- ft950325_0003_1531S002001M.fits 8 -- ft950325_0003_1531S002201M.fits 9 -- ft950325_0003_1531S003001M.fits 10 -- ft950325_0003_1531S003401M.fits 11 -- ft950325_0003_1531S003601M.fits 12 -- ft950325_0003_1531S003801M.fits 13 -- ft950325_0003_1531S004001M.fits 14 -- ft950325_0003_1531S004401M.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S000101M.fits 2 -- ft950325_0003_1531S000301M.fits 3 -- ft950325_0003_1531S000701M.fits 4 -- ft950325_0003_1531S001401M.fits 5 -- ft950325_0003_1531S001601M.fits 6 -- ft950325_0003_1531S001801M.fits 7 -- ft950325_0003_1531S002001M.fits 8 -- ft950325_0003_1531S002201M.fits 9 -- ft950325_0003_1531S003001M.fits 10 -- ft950325_0003_1531S003401M.fits 11 -- ft950325_0003_1531S003601M.fits 12 -- ft950325_0003_1531S003801M.fits 13 -- ft950325_0003_1531S004001M.fits 14 -- ft950325_0003_1531S004401M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000s000301l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S000501L.fits 2 -- ft950325_0003_1531S000801L.fits 3 -- ft950325_0003_1531S001001L.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S000501L.fits 2 -- ft950325_0003_1531S000801L.fits 3 -- ft950325_0003_1531S001001L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000367 events
ft950325_0003_1531S001201H.fits ft950325_0003_1531S002801H.fits-> Ignoring the following files containing 000000096 events
ft950325_0003_1531S001701M.fits ft950325_0003_1531S003501M.fits ft950325_0003_1531S003901M.fits-> Ignoring the following files containing 000000016 events
ft950325_0003_1531S000901L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 14 photon cnt = 367884 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 2 photon cnt = 352 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 3 photon cnt = 5715 SIS1SORTSPLIT:LO:s100401l.prelist merge count = 1 photon cnt = 16 SIS1SORTSPLIT:LO:s100501m.prelist merge count = 14 photon cnt = 30066 SIS1SORTSPLIT:LO:s100601m.prelist merge count = 3 photon cnt = 96 SIS1SORTSPLIT:LO:Total filenames split = 37 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad83033000s100101h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S100201H.fits 2 -- ft950325_0003_1531S100401H.fits 3 -- ft950325_0003_1531S100601H.fits 4 -- ft950325_0003_1531S101101H.fits 5 -- ft950325_0003_1531S101501H.fits 6 -- ft950325_0003_1531S101901H.fits 7 -- ft950325_0003_1531S102301H.fits 8 -- ft950325_0003_1531S102501H.fits 9 -- ft950325_0003_1531S102701H.fits 10 -- ft950325_0003_1531S103101H.fits 11 -- ft950325_0003_1531S103301H.fits 12 -- ft950325_0003_1531S103701H.fits 13 -- ft950325_0003_1531S104101H.fits 14 -- ft950325_0003_1531S104301H.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S100201H.fits 2 -- ft950325_0003_1531S100401H.fits 3 -- ft950325_0003_1531S100601H.fits 4 -- ft950325_0003_1531S101101H.fits 5 -- ft950325_0003_1531S101501H.fits 6 -- ft950325_0003_1531S101901H.fits 7 -- ft950325_0003_1531S102301H.fits 8 -- ft950325_0003_1531S102501H.fits 9 -- ft950325_0003_1531S102701H.fits 10 -- ft950325_0003_1531S103101H.fits 11 -- ft950325_0003_1531S103301H.fits 12 -- ft950325_0003_1531S103701H.fits 13 -- ft950325_0003_1531S104101H.fits 14 -- ft950325_0003_1531S104301H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000s100201m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S100101M.fits 2 -- ft950325_0003_1531S100301M.fits 3 -- ft950325_0003_1531S100701M.fits 4 -- ft950325_0003_1531S101401M.fits 5 -- ft950325_0003_1531S101601M.fits 6 -- ft950325_0003_1531S101801M.fits 7 -- ft950325_0003_1531S102001M.fits 8 -- ft950325_0003_1531S102201M.fits 9 -- ft950325_0003_1531S103001M.fits 10 -- ft950325_0003_1531S103401M.fits 11 -- ft950325_0003_1531S103601M.fits 12 -- ft950325_0003_1531S103801M.fits 13 -- ft950325_0003_1531S104001M.fits 14 -- ft950325_0003_1531S104401M.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S100101M.fits 2 -- ft950325_0003_1531S100301M.fits 3 -- ft950325_0003_1531S100701M.fits 4 -- ft950325_0003_1531S101401M.fits 5 -- ft950325_0003_1531S101601M.fits 6 -- ft950325_0003_1531S101801M.fits 7 -- ft950325_0003_1531S102001M.fits 8 -- ft950325_0003_1531S102201M.fits 9 -- ft950325_0003_1531S103001M.fits 10 -- ft950325_0003_1531S103401M.fits 11 -- ft950325_0003_1531S103601M.fits 12 -- ft950325_0003_1531S103801M.fits 13 -- ft950325_0003_1531S104001M.fits 14 -- ft950325_0003_1531S104401M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83033000s100301l.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950325_0003_1531S100501L.fits 2 -- ft950325_0003_1531S100801L.fits 3 -- ft950325_0003_1531S101001L.fits Merging binary extension #: 2 1 -- ft950325_0003_1531S100501L.fits 2 -- ft950325_0003_1531S100801L.fits 3 -- ft950325_0003_1531S101001L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000352 events
ft950325_0003_1531S101201H.fits ft950325_0003_1531S102801H.fits-> Ignoring the following files containing 000000096 events
ft950325_0003_1531S101701M.fits ft950325_0003_1531S103501M.fits ft950325_0003_1531S103901M.fits-> Ignoring the following files containing 000000016 events
ft950325_0003_1531S100901L.fits-> Tar-ing together the leftover raw files
a ft950325_0003_1531G200270H.fits 40K a ft950325_0003_1531G200370H.fits 40K a ft950325_0003_1531G200670M.fits 40K a ft950325_0003_1531G200870H.fits 40K a ft950325_0003_1531G200970H.fits 40K a ft950325_0003_1531G201470M.fits 40K a ft950325_0003_1531G201670M.fits 40K a ft950325_0003_1531G202070L.fits 43K a ft950325_0003_1531G202370H.fits 40K a ft950325_0003_1531G202970M.fits 40K a ft950325_0003_1531G203170H.fits 40K a ft950325_0003_1531G203270H.fits 40K a ft950325_0003_1531G203370H.fits 40K a ft950325_0003_1531G204370H.fits 40K a ft950325_0003_1531G204470H.fits 40K a ft950325_0003_1531G205470H.fits 40K a ft950325_0003_1531G205570H.fits 40K a ft950325_0003_1531G205970H.fits 40K a ft950325_0003_1531G206370H.fits 40K a ft950325_0003_1531G206470H.fits 40K a ft950325_0003_1531G207270H.fits 40K a ft950325_0003_1531G207370H.fits 40K a ft950325_0003_1531G208170H.fits 40K a ft950325_0003_1531G208270H.fits 40K a ft950325_0003_1531G208870H.fits 40K a ft950325_0003_1531G209570H.fits 40K a ft950325_0003_1531G209670H.fits 40K a ft950325_0003_1531G210270H.fits 40K a ft950325_0003_1531G210470H.fits 40K a ft950325_0003_1531G300270H.fits 40K a ft950325_0003_1531G300470H.fits 40K a ft950325_0003_1531G300670M.fits 40K a ft950325_0003_1531G300870H.fits 40K a ft950325_0003_1531G300970H.fits 40K a ft950325_0003_1531G301570H.fits 40K a ft950325_0003_1531G301770M.fits 40K a ft950325_0003_1531G301970M.fits 40K a ft950325_0003_1531G302370L.fits 43K a ft950325_0003_1531G302670H.fits 40K a ft950325_0003_1531G302770H.fits 40K a ft950325_0003_1531G303370M.fits 40K a ft950325_0003_1531G303570H.fits 40K a ft950325_0003_1531G303670H.fits 40K a ft950325_0003_1531G303770H.fits 40K a ft950325_0003_1531G304770H.fits 40K a ft950325_0003_1531G304970H.fits 40K a ft950325_0003_1531G306070H.fits 40K a ft950325_0003_1531G306170H.fits 40K a ft950325_0003_1531G306570H.fits 40K a ft950325_0003_1531G306670H.fits 40K a ft950325_0003_1531G307070H.fits 40K a ft950325_0003_1531G307170H.fits 40K a ft950325_0003_1531G308070H.fits 40K a ft950325_0003_1531G308170H.fits 40K a ft950325_0003_1531G308670H.fits 40K a ft950325_0003_1531G309070H.fits 40K a ft950325_0003_1531G309870H.fits 40K a ft950325_0003_1531G310370H.fits 40K a ft950325_0003_1531G310470H.fits 40K a ft950325_0003_1531G310570H.fits 40K a ft950325_0003_1531G310770H.fits 40K a ft950325_0003_1531G310870H.fits 40K a ft950325_0003_1531S000901L.fits 40K a ft950325_0003_1531S001201H.fits 43K a ft950325_0003_1531S001701M.fits 40K a ft950325_0003_1531S002801H.fits 48K a ft950325_0003_1531S003501M.fits 40K a ft950325_0003_1531S003901M.fits 40K a ft950325_0003_1531S100901L.fits 40K a ft950325_0003_1531S101201H.fits 43K a ft950325_0003_1531S101701M.fits 40K a ft950325_0003_1531S102801H.fits 48K a ft950325_0003_1531S103501M.fits 40K a ft950325_0003_1531S103901M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft950325_0003.1531 'ft950325_0003.1531' is successfully opened Data Start Time is 70243415.63 (950325 000335) Time Margin 2.0 sec included Sync error detected in 609 th SF Sync error detected in 614 th SF Sync error detected in 13630 th SF Sync error detected in 13631 th SF Sync error detected in 13632 th SF Sync error detected in 16079 th SF 'ft950325_0003.1531' EOF detected, sf=16939 Data End Time is 70299067.45 (950325 153107) Gain History is written in ft950325_0003_1531.ghf-> Checking if column CAL_START in ft950325_0003_1531.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft950325_0003_1531.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g200270l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g200370m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g200470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83033000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g300270l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g300370m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000g300470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83033000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000201m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000212m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s000301l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100201m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100212m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70246859.115216 ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100301l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100302l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad83033000s100312l.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 70253639.592500 ASCALIN_V0.9t : Detected gap > 15min in attitude file:
Date and time are: 95/ 3/25 0: 3 mjd=49801.002083 Orbit file name is ./frf.orbit.210 Epoch of Orbital Elements: 1995/3/20 17:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa950325_0003.1531 S0-HK file: ft950325_0003_1531S0HK.fits S1-HK file: ft950325_0003_1531S1HK.fits G2-HK file: ft950325_0003_1531G2HK.fits G3-HK file: ft950325_0003_1531G3HK.fits output FITS File: ft950325_0003_1531.mkf Total 1739 Data bins were processed.-> Checking if column TIME in ft950325_0003_1531.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 13332.012 The mean of the selected column is 26.557793 The standard deviation of the selected column is 47.389477 The minimum of selected column is 4.3750134 The maximum of selected column is 610.43945 The number of points used in calculation is 502-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<168.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.31E+05 16365 0100
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13608 7071 0 6537 0 0
Writing events file
7071 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13608 7071 0 6537 0 0
in 19703.35 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 7071
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 3958
Flickering pixels iter, pixels & cnts : 1 6 31
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 7071
Number of image cts rejected (N, %) : 3989 56.4135208
By chip : 0 1 2 3
Pixels rejected : 0 11 0 0
Image counts : 0 7071 0 0
Image cts rejected: 0 3989 0 0
Image cts rej (%) : 0.00 56.41 0.00 0.00
filtering data...
Total counts : 0 7071 0 0
Total cts rejected: 0 3989 0 0
Total cts rej (%) : 0.00 56.41 0.00 0.00
Number of clean counts accepted : 3082
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad83033000s000102h.evt use_events=no
Wrote cleaned events file to ad83033000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad83033000s000112h.unf into ad83033000s000112h.evtThe sum of the selected column is 13332.012 The mean of the selected column is 26.557793 The standard deviation of the selected column is 47.389477 The minimum of selected column is 4.3750134 The maximum of selected column is 610.43945 The number of points used in calculation is 502-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<168.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.31E+05 17379 0100
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13977 7167 0 6810 0 0
Writing events file
7167 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13977 7167 0 6810 0 0
in 19703.35 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 7167
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 3958
Flickering pixels iter, pixels & cnts : 1 6 31
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 11
Number of (internal) image counts : 7167
Number of image cts rejected (N, %) : 3989 55.6578751
By chip : 0 1 2 3
Pixels rejected : 0 11 0 0
Image counts : 0 7167 0 0
Image cts rejected: 0 3989 0 0
Image cts rej (%) : 0.00 55.66 0.00 0.00
filtering data...
Total counts : 0 7167 0 0
Total cts rejected: 0 3989 0 0
Total cts rej (%) : 0.00 55.66 0.00 0.00
Number of clean counts accepted : 3178
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 11
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad83033000s000112h.evt use_events=no
Wrote cleaned events file to ad83033000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad83033000s000201m.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.63E+04 1932 0100
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1664 876 0 788 0 0
Writing events file
876 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1664 876 0 788 0 0
in 2373.49 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 876
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 507
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 4
Number of (internal) image counts : 876
Number of image cts rejected (N, %) : 507 57.8767128
By chip : 0 1 2 3
Pixels rejected : 0 4 0 0
Image counts : 0 876 0 0
Image cts rejected: 0 507 0 0
Image cts rej (%) : 0.00 57.88 0.00 0.00
filtering data...
Total counts : 0 876 0 0
Total cts rejected: 0 507 0 0
Total cts rej (%) : 0.00 57.88 0.00 0.00
Number of clean counts accepted : 369
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 4
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad83033000s000202m.evt use_events=no
Wrote cleaned events file to ad83033000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad83033000s000212m.unf into ad83033000s000212m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.63E+04 2015 0100
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s000212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1696 895 0 801 0 0
Writing events file
895 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1696 895 0 801 0 0
in 2373.49 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 895
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 507
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 4
Number of (internal) image counts : 895
Number of image cts rejected (N, %) : 507 56.6480446
By chip : 0 1 2 3
Pixels rejected : 0 4 0 0
Image counts : 0 895 0 0
Image cts rejected: 0 507 0 0
Image cts rej (%) : 0.00 56.65 0.00 0.00
filtering data...
Total counts : 0 895 0 0
Total cts rejected: 0 507 0 0
Total cts rej (%) : 0.00 56.65 0.00 0.00
Number of clean counts accepted : 388
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 4
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad83033000s000212m.evt use_events=no
Wrote cleaned events file to ad83033000s000212m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad83033000s000301l.unf because of modeThe sum of the selected column is 23341.325 The mean of the selected column is 46.682649 The standard deviation of the selected column is 94.059999 The minimum of selected column is 6.7500477 The maximum of selected column is 1221.1602 The number of points used in calculation is 500-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<328.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.31E+05 71293 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
64162 39197 0 24965 0 0
Writing events file
39197 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
64162 39197 0 24965 0 0
in 19651.35 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 39197
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 15 36118
Flickering pixels iter, pixels & cnts : 1 6 336
Number of pixels rejected : 21
Number of (internal) image counts : 39197
Number of image cts rejected (N, %) : 36454 93.0020142
By chip : 0 1 2 3
Pixels rejected : 0 0 0 21
Image counts : 0 0 0 39197
Image cts rejected: 0 0 0 36454
Image cts rej (%) : 0.00 0.00 0.00 93.00
filtering data...
Total counts : 0 0 0 39197
Total cts rejected: 0 0 0 36454
Total cts rej (%) : 0.00 0.00 0.00 93.00
Number of clean counts accepted : 2743
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83033000s100102h.evt use_events=no
Wrote cleaned events file to ad83033000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad83033000s100112h.unf into ad83033000s100112h.evtThe sum of the selected column is 23341.325 The mean of the selected column is 46.682649 The standard deviation of the selected column is 94.059999 The minimum of selected column is 6.7500477 The maximum of selected column is 1221.1602 The number of points used in calculation is 500-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0.0 && S1_PIXL3<328.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.31E+05 72040 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
64447 39269 0 25178 0 0
Writing events file
39269 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
64447 39269 0 25178 0 0
in 19651.35 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 39269
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 15 36120
Flickering pixels iter, pixels & cnts : 1 6 336
Number of pixels rejected : 21
Number of (internal) image counts : 39269
Number of image cts rejected (N, %) : 36456 92.8365860
By chip : 0 1 2 3
Pixels rejected : 0 0 0 21
Image counts : 0 0 0 39269
Image cts rejected: 0 0 0 36456
Image cts rej (%) : 0.00 0.00 0.00 92.84
filtering data...
Total counts : 0 0 0 39269
Total cts rejected: 0 0 0 36456
Total cts rej (%) : 0.00 0.00 0.00 92.84
Number of clean counts accepted : 2813
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 21
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad83033000s100112h.evt use_events=no
Wrote cleaned events file to ad83033000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad83033000s100201m.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.63E+04 10744 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10201 4649 0 5552 0 0
Writing events file
4649 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10201 4649 0 5552 0 0
in 2373.49 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 4649
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 14 4279
Flickering pixels iter, pixels & cnts : 1 5 45
Number of pixels rejected : 19
Number of (internal) image counts : 4649
Number of image cts rejected (N, %) : 4324 93.0092468
By chip : 0 1 2 3
Pixels rejected : 0 0 0 19
Image counts : 0 0 0 4649
Image cts rejected: 0 0 0 4324
Image cts rej (%) : 0.00 0.00 0.00 93.01
filtering data...
Total counts : 0 0 0 4649
Total cts rejected: 0 0 0 4324
Total cts rej (%) : 0.00 0.00 0.00 93.01
Number of clean counts accepted : 325
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 19
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83033000s100202m.evt use_events=no
Wrote cleaned events file to ad83033000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad83033000s100212m.unf into ad83033000s100212m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.63E+04 10793 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10224 4658 0 5566 0 0
Writing events file
4658 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10224 4658 0 5566 0 0
in 2373.49 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 4658
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 14 4279
Flickering pixels iter, pixels & cnts : 1 5 45
Number of pixels rejected : 19
Number of (internal) image counts : 4658
Number of image cts rejected (N, %) : 4324 92.8295441
By chip : 0 1 2 3
Pixels rejected : 0 0 0 19
Image counts : 0 0 0 4658
Image cts rejected: 0 0 0 4324
Image cts rej (%) : 0.00 0.00 0.00 92.83
filtering data...
Total counts : 0 0 0 4658
Total cts rejected: 0 0 0 4324
Total cts rej (%) : 0.00 0.00 0.00 92.83
Number of clean counts accepted : 334
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 19
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad83033000s100212m.evt use_events=no
Wrote cleaned events file to ad83033000s100212m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad83033000s100301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT LOW 25/03/95 02:40:19 0.29E+04 1565 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83033000s100302l.evt use_events=no
Wrote cleaned events file to ad83033000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad83033000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 LOW 25/03/95 02:40:19 0.29E+04 1571 0001
Processing file: /data/data23/seq_proc/83033000.006/ad83033000s100312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data23/seq_proc/83033000.006/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data23/seq_proc/83033000.006/screen_in_event.xsl
reading data file: /data/data23/seq_proc/83033000.006/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad83033000s100312l.evt use_events=no
Wrote cleaned events file to ad83033000s100312l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad83033000s100312l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.unf
Total Good Bad: Region Time Phase Cut
27894 7039 15162 5693 0 0
Writing events file
7039 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27894 7039 15162 5693 0 0
in 20265.51 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
7039 6253 786
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83033000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 6253 in ad83033000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.unf
Total Good Bad: Region Time Phase Cut
6834 9 2660 4165 0 0
Writing events file
9 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6834 9 2660 4165 0 0
in 31.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
9 9 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83033000g200270l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad83033000g200370m.unf into ad83033000g200370m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4446 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.unf
Total Good Bad: Region Time Phase Cut
4446 648 2537 1261 0 0
Writing events file
648 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4446 648 2537 1261 0 0
in 2047.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
648 576 72
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83033000g200370m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 576 in ad83033000g200370m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2221 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.unf
Total Good Bad: Region Time Phase Cut
2221 780 1258 183 0 0
Writing events file
780 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2221 780 1258 183 0 0
in 2028.17 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
780 705 75
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83033000g200470h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 705 in ad83033000g200470h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.unf
Total Good Bad: Region Time Phase Cut
27484 7895 13448 6141 0 0
Writing events file
7895 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27484 7895 13448 6141 0 0
in 20261.51 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
7895 7009 886
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83033000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 7009 in ad83033000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.unf
Total Good Bad: Region Time Phase Cut
6820 17 2230 4573 0 0
Writing events file
17 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6820 17 2230 4573 0 0
in 31.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
17 17 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83033000g300270l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad83033000g300370m.unf into ad83033000g300370m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4167 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.unf
Total Good Bad: Region Time Phase Cut
4167 730 2138 1299 0 0
Writing events file
730 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4167 730 2138 1299 0 0
in 2047.99 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
730 663 67
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83033000g300370m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 663 in ad83033000g300370m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2049 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.unf
Total Good Bad: Region Time Phase Cut
2049 757 1091 201 0 0
Writing events file
757 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2049 757 1091 201 0 0
in 2028.17 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
757 667 90
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!screen:ASCA > read events ad83033000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83033000g300470h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 667 in ad83033000g300470h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad83033000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6779
Mean RA/DEC/ROLL : 213.4600 71.3722 332.6779
Pnt RA/DEC/ROLL : 213.3499 71.4116 332.6779
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 41
Total GTI (secs) : 20265.512
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3055.9873047 3055.9873047
20 Percent Complete: Total/live time: 5506.4990234 5506.4990234
30 Percent Complete: Total/live time: 6741.9990234 6741.9990234
40 Percent Complete: Total/live time: 8490.8212891 8490.8212891
50 Percent Complete: Total/live time: 14007.6826172 14007.6826172
60 Percent Complete: Total/live time: 14007.6826172 14007.6826172
70 Percent Complete: Total/live time: 14748.6806641 14748.6806641
80 Percent Complete: Total/live time: 19094.0156250 19094.0156250
90 Percent Complete: Total/live time: 19094.0156250 19094.0156250
100 Percent Complete: Total/live time: 20265.5117188 20265.5117188
Number of attitude steps used: 42
Number of attitude steps avail: 58644
Mean RA/DEC pixel offset: -13.7494 -3.9816
writing expo file: ad83033000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 6172 81 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6253 6172 81 0 0 0
in 20265.51 seconds
Image has 6172 counts for 0.3046 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 2797 81 0 0 3375
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6253 2797 81 0 0 3375
in 20265.51 seconds
Image has 2797 counts for 0.1380 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 3397 81 0 0 2775
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6253 3397 81 0 0 2775
in 20265.51 seconds
Image has 3397 counts for 0.1676 counts/sec
Command not found; type ? for a command listing
!ad83033000g200170h:ASCA >
!ad83033000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g200170h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g200170h:ASCA > read events ad83033000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g200170h:ASCA-GIS2-PH > set image sky
!ad83033000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad83033000g200170h:ASCA-GIS2-PH > extract image
!ad83033000g200170h:ASCA-GIS2-PH > save image outfile=ad83033000g200170h.img
Wrote image to file ad83033000g200170h.img
!ad83033000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83033000g200170h:ASCA-GIS2-PH > extract image
!ad83033000g200170h:ASCA-GIS2-PH > save image outfile=ad83033000g200170h_lo.img
Wrote image to file ad83033000g200170h_lo.img
!ad83033000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad83033000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g200170h:ASCA-GIS2-PH > extract image
!ad83033000g200170h:ASCA-GIS2-PH > save image outfile=ad83033000g200170h_hi.img
Wrote image to file ad83033000g200170h_hi.img
!ad83033000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83033000g200270l.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g200270l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6847
Mean RA/DEC/ROLL : 213.4586 71.3714 332.6847
Pnt RA/DEC/ROLL : 213.3424 71.4110 332.6847
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 2
Total GTI (secs) : 31.975
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 13.9749775 13.9749775
20 Percent Complete: Total/live time: 13.9749775 13.9749775
30 Percent Complete: Total/live time: 31.9750118 31.9750118
100 Percent Complete: Total/live time: 31.9750118 31.9750118
Number of attitude steps used: 3
Number of attitude steps avail: 164
Mean RA/DEC pixel offset: -9.1144 -2.8903
writing expo file: ad83033000g200270l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g200270l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g200270l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 9 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9 9 0 0 0 0
in 31.98 seconds
Image has 9 counts for 0.2815 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 4 0 0 0 5
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9 4 0 0 0 5
in 31.98 seconds
Image has 4 counts for 0.1251 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 5 0 0 0 4
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9 5 0 0 0 4
in 31.98 seconds
Image has 5 counts for 0.1564 counts/sec
Command not found; type ? for a command listing
!ad83033000g200270l:ASCA >
!ad83033000g200270l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g200270l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g200270l:ASCA > read events ad83033000g200270l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g200270l:ASCA-GIS2-PH > set image sky
!ad83033000g200270l:ASCA-GIS2-PH > filter region corner_point.reg
!ad83033000g200270l:ASCA-GIS2-PH > extract image
!ad83033000g200270l:ASCA-GIS2-PH > save image outfile=ad83033000g200270l.img
Wrote image to file ad83033000g200270l.img
!ad83033000g200270l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83033000g200270l:ASCA-GIS2-PH > extract image
!ad83033000g200270l:ASCA-GIS2-PH > save image outfile=ad83033000g200270l_lo.img
Wrote image to file ad83033000g200270l_lo.img
!ad83033000g200270l:ASCA-GIS2-PH > clear pha_cut
!ad83033000g200270l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g200270l:ASCA-GIS2-PH > extract image
!ad83033000g200270l:ASCA-GIS2-PH > save image outfile=ad83033000g200270l_hi.img
Wrote image to file ad83033000g200270l_hi.img
!ad83033000g200270l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83033000g200370m.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g200370m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6742
Mean RA/DEC/ROLL : 213.2621 71.3874 332.6742
Pnt RA/DEC/ROLL : 213.9643 71.3720 332.6742
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 4
Total GTI (secs) : 2047.986
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 285.9920654 285.9920654
20 Percent Complete: Total/live time: 469.9915771 469.9915771
30 Percent Complete: Total/live time: 853.9903564 853.9903564
40 Percent Complete: Total/live time: 853.9903564 853.9903564
50 Percent Complete: Total/live time: 1135.9895020 1135.9895020
60 Percent Complete: Total/live time: 1577.9880371 1577.9880371
70 Percent Complete: Total/live time: 1577.9880371 1577.9880371
80 Percent Complete: Total/live time: 1829.9871826 1829.9871826
90 Percent Complete: Total/live time: 2047.9859619 2047.9859619
100 Percent Complete: Total/live time: 2047.9859619 2047.9859619
Number of attitude steps used: 17
Number of attitude steps avail: 2883
Mean RA/DEC pixel offset: -11.9036 -4.0915
writing expo file: ad83033000g200370m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g200370m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g200370m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 572 4 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
576 572 4 0 0 0
in 2047.99 seconds
Image has 572 counts for 0.2793 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 281 4 0 0 291
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
576 281 4 0 0 291
in 2047.99 seconds
Image has 281 counts for 0.1372 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 293 4 0 0 279
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
576 293 4 0 0 279
in 2047.99 seconds
Image has 293 counts for 0.1431 counts/sec
Command not found; type ? for a command listing
!ad83033000g200370m:ASCA >
!ad83033000g200370m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g200370m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g200370m:ASCA > read events ad83033000g200370m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g200370m:ASCA-GIS2-PH > set image sky
!ad83033000g200370m:ASCA-GIS2-PH > filter region corner_point.reg
!ad83033000g200370m:ASCA-GIS2-PH > extract image
!ad83033000g200370m:ASCA-GIS2-PH > save image outfile=ad83033000g200370m.img
Wrote image to file ad83033000g200370m.img
!ad83033000g200370m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83033000g200370m:ASCA-GIS2-PH > extract image
!ad83033000g200370m:ASCA-GIS2-PH > save image outfile=ad83033000g200370m_lo.img
Wrote image to file ad83033000g200370m_lo.img
!ad83033000g200370m:ASCA-GIS2-PH > clear pha_cut
!ad83033000g200370m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g200370m:ASCA-GIS2-PH > extract image
!ad83033000g200370m:ASCA-GIS2-PH > save image outfile=ad83033000g200370m_hi.img
Wrote image to file ad83033000g200370m_hi.img
!ad83033000g200370m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83033000g200470h.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g200470h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6750
Mean RA/DEC/ROLL : 213.4580 71.3713 332.6750
Pnt RA/DEC/ROLL : 213.3427 71.4086 332.6750
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 3
Total GTI (secs) : 2028.169
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 809.4976196 809.4976196
20 Percent Complete: Total/live time: 809.4976196 809.4976196
30 Percent Complete: Total/live time: 815.4976196 815.4976196
40 Percent Complete: Total/live time: 2028.1684570 2028.1684570
100 Percent Complete: Total/live time: 2028.1684570 2028.1684570
Number of attitude steps used: 4
Number of attitude steps avail: 4214
Mean RA/DEC pixel offset: -9.9863 -3.2688
writing expo file: ad83033000g200470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g200470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g200470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 705 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 696 9 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
705 696 9 0 0 0
in 2028.17 seconds
Image has 696 counts for 0.3432 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 300 9 0 0 396
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
705 300 9 0 0 396
in 2028.17 seconds
Image has 300 counts for 0.1479 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 399 9 0 0 297
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
705 399 9 0 0 297
in 2028.17 seconds
Image has 399 counts for 0.1967 counts/sec
Command not found; type ? for a command listing
!ad83033000g200470h:ASCA >
!ad83033000g200470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g200470h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g200470h:ASCA > read events ad83033000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g200470h:ASCA-GIS2-PH > set image sky
!ad83033000g200470h:ASCA-GIS2-PH > filter region corner_point.reg
!ad83033000g200470h:ASCA-GIS2-PH > extract image
!ad83033000g200470h:ASCA-GIS2-PH > save image outfile=ad83033000g200470h.img
Wrote image to file ad83033000g200470h.img
!ad83033000g200470h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83033000g200470h:ASCA-GIS2-PH > extract image
!ad83033000g200470h:ASCA-GIS2-PH > save image outfile=ad83033000g200470h_lo.img
Wrote image to file ad83033000g200470h_lo.img
!ad83033000g200470h:ASCA-GIS2-PH > clear pha_cut
!ad83033000g200470h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g200470h:ASCA-GIS2-PH > extract image
!ad83033000g200470h:ASCA-GIS2-PH > save image outfile=ad83033000g200470h_hi.img
Wrote image to file ad83033000g200470h_hi.img
!ad83033000g200470h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83033000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad83033000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6161
Mean RA/DEC/ROLL : 213.3949 71.3857 332.6161
Pnt RA/DEC/ROLL : 213.4152 71.3981 332.6161
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 42
Total GTI (secs) : 20261.512
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3055.9873047 3055.9873047
20 Percent Complete: Total/live time: 5504.4990234 5504.4990234
30 Percent Complete: Total/live time: 6739.9990234 6739.9990234
40 Percent Complete: Total/live time: 8488.8212891 8488.8212891
50 Percent Complete: Total/live time: 14003.6826172 14003.6826172
60 Percent Complete: Total/live time: 14003.6826172 14003.6826172
70 Percent Complete: Total/live time: 14744.6806641 14744.6806641
80 Percent Complete: Total/live time: 19090.0156250 19090.0156250
90 Percent Complete: Total/live time: 19090.0156250 19090.0156250
100 Percent Complete: Total/live time: 20261.5117188 20261.5117188
Number of attitude steps used: 42
Number of attitude steps avail: 58644
Mean RA/DEC pixel offset: -1.9583 -2.8103
writing expo file: ad83033000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 6921 88 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7009 6921 88 0 0 0
in 20261.51 seconds
Image has 6921 counts for 0.3416 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 3217 88 0 0 3704
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7009 3217 88 0 0 3704
in 20261.51 seconds
Image has 3217 counts for 0.1588 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 3728 88 0 0 3193
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7009 3728 88 0 0 3193
in 20261.51 seconds
Image has 3728 counts for 0.1840 counts/sec
Command not found; type ? for a command listing
!ad83033000g300170h:ASCA >
!ad83033000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g300170h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g300170h:ASCA > read events ad83033000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g300170h:ASCA-GIS3-PH > set image sky
!ad83033000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad83033000g300170h:ASCA-GIS3-PH > extract image
!ad83033000g300170h:ASCA-GIS3-PH > save image outfile=ad83033000g300170h.img
Wrote image to file ad83033000g300170h.img
!ad83033000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83033000g300170h:ASCA-GIS3-PH > extract image
!ad83033000g300170h:ASCA-GIS3-PH > save image outfile=ad83033000g300170h_lo.img
Wrote image to file ad83033000g300170h_lo.img
!ad83033000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad83033000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g300170h:ASCA-GIS3-PH > extract image
!ad83033000g300170h:ASCA-GIS3-PH > save image outfile=ad83033000g300170h_hi.img
Wrote image to file ad83033000g300170h_hi.img
!ad83033000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83033000g300270l.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g300270l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6228
Mean RA/DEC/ROLL : 213.3933 71.3849 332.6228
Pnt RA/DEC/ROLL : 213.4077 71.3975 332.6228
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 2
Total GTI (secs) : 31.975
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 13.9749775 13.9749775
20 Percent Complete: Total/live time: 13.9749775 13.9749775
30 Percent Complete: Total/live time: 31.9750118 31.9750118
100 Percent Complete: Total/live time: 31.9750118 31.9750118
Number of attitude steps used: 3
Number of attitude steps avail: 164
Mean RA/DEC pixel offset: -1.0620 -2.0904
writing expo file: ad83033000g300270l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g300270l.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g300270l
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 17 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17 17 0 0 0 0
in 31.98 seconds
Image has 17 counts for 0.5317 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 10 0 0 0 7
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17 10 0 0 0 7
in 31.98 seconds
Image has 10 counts for 0.3127 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 7 0 0 0 10
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17 7 0 0 0 10
in 31.98 seconds
Image has 7 counts for 0.2189 counts/sec
Command not found; type ? for a command listing
!ad83033000g300270l:ASCA >
!ad83033000g300270l:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g300270l:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g300270l:ASCA > read events ad83033000g300270l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g300270l:ASCA-GIS3-PH > set image sky
!ad83033000g300270l:ASCA-GIS3-PH > filter region corner_point.reg
!ad83033000g300270l:ASCA-GIS3-PH > extract image
!ad83033000g300270l:ASCA-GIS3-PH > save image outfile=ad83033000g300270l.img
Wrote image to file ad83033000g300270l.img
!ad83033000g300270l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83033000g300270l:ASCA-GIS3-PH > extract image
!ad83033000g300270l:ASCA-GIS3-PH > save image outfile=ad83033000g300270l_lo.img
Wrote image to file ad83033000g300270l_lo.img
!ad83033000g300270l:ASCA-GIS3-PH > clear pha_cut
!ad83033000g300270l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g300270l:ASCA-GIS3-PH > extract image
!ad83033000g300270l:ASCA-GIS3-PH > save image outfile=ad83033000g300270l_hi.img
Wrote image to file ad83033000g300270l_hi.img
!ad83033000g300270l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83033000g300370m.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g300370m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6124
Mean RA/DEC/ROLL : 213.2048 71.3997 332.6124
Pnt RA/DEC/ROLL : 214.0290 71.3583 332.6124
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 4
Total GTI (secs) : 2047.986
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 285.9920654 285.9920654
20 Percent Complete: Total/live time: 469.9915771 469.9915771
30 Percent Complete: Total/live time: 853.9903564 853.9903564
40 Percent Complete: Total/live time: 853.9903564 853.9903564
50 Percent Complete: Total/live time: 1135.9895020 1135.9895020
60 Percent Complete: Total/live time: 1577.9880371 1577.9880371
70 Percent Complete: Total/live time: 1577.9880371 1577.9880371
80 Percent Complete: Total/live time: 1829.9871826 1829.9871826
90 Percent Complete: Total/live time: 2047.9859619 2047.9859619
100 Percent Complete: Total/live time: 2047.9859619 2047.9859619
Number of attitude steps used: 17
Number of attitude steps avail: 2883
Mean RA/DEC pixel offset: -0.5354 -2.9622
writing expo file: ad83033000g300370m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g300370m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g300370m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 661 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
663 661 2 0 0 0
in 2047.99 seconds
Image has 661 counts for 0.3228 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 316 2 0 0 345
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
663 316 2 0 0 345
in 2047.99 seconds
Image has 316 counts for 0.1543 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 349 2 0 0 312
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
663 349 2 0 0 312
in 2047.99 seconds
Image has 349 counts for 0.1704 counts/sec
Command not found; type ? for a command listing
!ad83033000g300370m:ASCA >
!ad83033000g300370m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g300370m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g300370m:ASCA > read events ad83033000g300370m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g300370m:ASCA-GIS3-PH > set image sky
!ad83033000g300370m:ASCA-GIS3-PH > filter region corner_point.reg
!ad83033000g300370m:ASCA-GIS3-PH > extract image
!ad83033000g300370m:ASCA-GIS3-PH > save image outfile=ad83033000g300370m.img
Wrote image to file ad83033000g300370m.img
!ad83033000g300370m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83033000g300370m:ASCA-GIS3-PH > extract image
!ad83033000g300370m:ASCA-GIS3-PH > save image outfile=ad83033000g300370m_lo.img
Wrote image to file ad83033000g300370m_lo.img
!ad83033000g300370m:ASCA-GIS3-PH > clear pha_cut
!ad83033000g300370m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g300370m:ASCA-GIS3-PH > extract image
!ad83033000g300370m:ASCA-GIS3-PH > save image outfile=ad83033000g300370m_hi.img
Wrote image to file ad83033000g300370m_hi.img
!ad83033000g300370m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83033000g300470h.expo
ASCAEXPO_V0.9b
reading data file: ad83033000g300470h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6132
Mean RA/DEC/ROLL : 213.3927 71.3848 332.6132
Pnt RA/DEC/ROLL : 213.4080 71.3951 332.6132
Image rebin factor : 1
Attitude Records : 67638
GTI intervals : 3
Total GTI (secs) : 2028.169
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 809.4976196 809.4976196
20 Percent Complete: Total/live time: 809.4976196 809.4976196
30 Percent Complete: Total/live time: 815.4976196 815.4976196
40 Percent Complete: Total/live time: 2028.1684570 2028.1684570
100 Percent Complete: Total/live time: 2028.1684570 2028.1684570
Number of attitude steps used: 4
Number of attitude steps avail: 4214
Mean RA/DEC pixel offset: -0.9273 -2.3689
writing expo file: ad83033000g300470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000g300470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000g300470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 667 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 661 6 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
667 661 6 0 0 0
in 2028.17 seconds
Image has 661 counts for 0.3259 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 314 6 0 0 347
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
667 314 6 0 0 347
in 2028.17 seconds
Image has 314 counts for 0.1548 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 348 6 0 0 313
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
667 348 6 0 0 313
in 2028.17 seconds
Image has 348 counts for 0.1716 counts/sec
Command not found; type ? for a command listing
!ad83033000g300470h:ASCA >
!ad83033000g300470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000g300470h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000g300470h:ASCA > read events ad83033000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000g300470h:ASCA-GIS3-PH > set image sky
!ad83033000g300470h:ASCA-GIS3-PH > filter region corner_point.reg
!ad83033000g300470h:ASCA-GIS3-PH > extract image
!ad83033000g300470h:ASCA-GIS3-PH > save image outfile=ad83033000g300470h.img
Wrote image to file ad83033000g300470h.img
!ad83033000g300470h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83033000g300470h:ASCA-GIS3-PH > extract image
!ad83033000g300470h:ASCA-GIS3-PH > save image outfile=ad83033000g300470h_lo.img
Wrote image to file ad83033000g300470h_lo.img
!ad83033000g300470h:ASCA-GIS3-PH > clear pha_cut
!ad83033000g300470h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83033000g300470h:ASCA-GIS3-PH > extract image
!ad83033000g300470h:ASCA-GIS3-PH > save image outfile=ad83033000g300470h_hi.img
Wrote image to file ad83033000g300470h_hi.img
!ad83033000g300470h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83033000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad83033000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6257
Mean RA/DEC/ROLL : 213.4049 71.3652 332.6257
Pnt RA/DEC/ROLL : 213.4061 71.4177 332.6257
Image rebin factor : 4
Attitude Records : 67638
Hot Pixels : 11
GTI intervals : 46
Total GTI (secs) : 19703.352
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2527.9365234 2527.9365234
20 Percent Complete: Total/live time: 4426.3730469 4426.3730469
30 Percent Complete: Total/live time: 6263.8251953 6263.8251953
40 Percent Complete: Total/live time: 8165.7778320 8165.7778320
50 Percent Complete: Total/live time: 12591.5273438 12591.5273438
60 Percent Complete: Total/live time: 12591.5273438 12591.5273438
70 Percent Complete: Total/live time: 16709.8125000 16709.8125000
80 Percent Complete: Total/live time: 16709.8125000 16709.8125000
90 Percent Complete: Total/live time: 18676.6816406 18676.6816406
100 Percent Complete: Total/live time: 19703.3515625 19703.3515625
Number of attitude steps used: 43
Number of attitude steps avail: 60754
Mean RA/DEC pixel offset: -71.1284 -99.5775
writing expo file: ad83033000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 3082 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3082 3082 0 0 0 0
in 19703.35 seconds
Image has 3082 counts for 0.1564 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 1928 0 0 0 1154
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3082 1928 0 0 0 1154
in 19703.35 seconds
Image has 1928 counts for 9.7851E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 1155 0 0 0 1927
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3082 1155 0 0 0 1927
in 19703.35 seconds
Image has 1155 counts for 5.8619E-02 counts/sec
Command not found; type ? for a command listing
!ad83033000s000102h:ASCA >
!ad83033000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000s000102h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000s000102h:ASCA > read events ad83033000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad83033000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad83033000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000102h.img
Wrote image to file ad83033000s000102h.img
!ad83033000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad83033000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000102h_lo.img
Wrote image to file ad83033000s000102h_lo.img
!ad83033000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad83033000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83033000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000102h_hi.img
Wrote image to file ad83033000s000102h_hi.img
!ad83033000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad83033000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad83033000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6222
Mean RA/DEC/ROLL : 213.2342 71.3782 332.6222
Pnt RA/DEC/ROLL : 214.0201 71.3776 332.6222
Image rebin factor : 4
Attitude Records : 67638
Hot Pixels : 4
GTI intervals : 3
Total GTI (secs) : 2373.489
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 285.9920654 285.9920654
20 Percent Complete: Total/live time: 883.7402344 883.7402344
30 Percent Complete: Total/live time: 883.7402344 883.7402344
40 Percent Complete: Total/live time: 1157.4893799 1157.4893799
50 Percent Complete: Total/live time: 1547.4434814 1547.4434814
60 Percent Complete: Total/live time: 1547.4434814 1547.4434814
70 Percent Complete: Total/live time: 1835.4426270 1835.4426270
80 Percent Complete: Total/live time: 2315.4409180 2315.4409180
90 Percent Complete: Total/live time: 2315.4409180 2315.4409180
100 Percent Complete: Total/live time: 2373.4892578 2373.4892578
Number of attitude steps used: 18
Number of attitude steps avail: 2927
Mean RA/DEC pixel offset: -58.0997 -98.2374
writing expo file: ad83033000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 369 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 369 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
369 369 0 0 0 0
in 2373.49 seconds
Image has 369 counts for 0.1555 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 233 0 0 0 136
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
369 233 0 0 0 136
in 2373.49 seconds
Image has 233 counts for 9.8168E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 136 0 0 0 233
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
369 136 0 0 0 233
in 2373.49 seconds
Image has 136 counts for 5.7300E-02 counts/sec
Command not found; type ? for a command listing
!ad83033000s000202m:ASCA >
!ad83033000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000s000202m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000s000202m:ASCA > read events ad83033000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad83033000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad83033000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000202m.img
Wrote image to file ad83033000s000202m.img
!ad83033000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad83033000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000202m_lo.img
Wrote image to file ad83033000s000202m_lo.img
!ad83033000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad83033000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83033000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83033000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83033000s000202m_hi.img
Wrote image to file ad83033000s000202m_hi.img
!ad83033000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad83033000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad83033000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6500
Mean RA/DEC/ROLL : 213.4308 71.3789 332.6500
Pnt RA/DEC/ROLL : 213.3804 71.4040 332.6500
Image rebin factor : 4
Attitude Records : 67638
Hot Pixels : 21
GTI intervals : 46
Total GTI (secs) : 19651.352
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2527.9365234 2527.9365234
20 Percent Complete: Total/live time: 4426.3730469 4426.3730469
30 Percent Complete: Total/live time: 6231.8251953 6231.8251953
40 Percent Complete: Total/live time: 8133.7778320 8133.7778320
50 Percent Complete: Total/live time: 12535.5273438 12535.5273438
60 Percent Complete: Total/live time: 12535.5273438 12535.5273438
70 Percent Complete: Total/live time: 16653.8125000 16653.8125000
80 Percent Complete: Total/live time: 16653.8125000 16653.8125000
90 Percent Complete: Total/live time: 18624.6816406 18624.6816406
100 Percent Complete: Total/live time: 19651.3515625 19651.3515625
Number of attitude steps used: 43
Number of attitude steps avail: 60754
Mean RA/DEC pixel offset: -75.4693 -29.3973
writing expo file: ad83033000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 2743 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2743 2743 0 0 0 0
in 19651.35 seconds
Image has 2743 counts for 0.1396 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 1592 0 0 0 1151
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2743 1592 0 0 0 1151
in 19651.35 seconds
Image has 1592 counts for 8.1012E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 1153 0 0 0 1590
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2743 1153 0 0 0 1590
in 19651.35 seconds
Image has 1153 counts for 5.8673E-02 counts/sec
Command not found; type ? for a command listing
!ad83033000s100102h:ASCA >
!ad83033000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000s100102h:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000s100102h:ASCA > read events ad83033000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad83033000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad83033000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100102h.img
Wrote image to file ad83033000s100102h.img
!ad83033000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad83033000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100102h_lo.img
Wrote image to file ad83033000s100102h_lo.img
!ad83033000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad83033000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83033000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100102h_hi.img
Wrote image to file ad83033000s100102h_hi.img
!ad83033000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad83033000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad83033000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950325_0003.1531
making an exposure map...
Aspect RA/DEC/ROLL : 213.3940 71.3919 332.6465
Mean RA/DEC/ROLL : 213.2555 71.3922 332.6465
Pnt RA/DEC/ROLL : 213.9940 71.3641 332.6465
Image rebin factor : 4
Attitude Records : 67638
Hot Pixels : 19
GTI intervals : 3
Total GTI (secs) : 2373.489
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 285.9920654 285.9920654
20 Percent Complete: Total/live time: 883.7402344 883.7402344
30 Percent Complete: Total/live time: 883.7402344 883.7402344
40 Percent Complete: Total/live time: 1157.4893799 1157.4893799
50 Percent Complete: Total/live time: 1547.4434814 1547.4434814
60 Percent Complete: Total/live time: 1547.4434814 1547.4434814
70 Percent Complete: Total/live time: 1835.4426270 1835.4426270
80 Percent Complete: Total/live time: 2315.4409180 2315.4409180
90 Percent Complete: Total/live time: 2315.4409180 2315.4409180
100 Percent Complete: Total/live time: 2373.4892578 2373.4892578
Number of attitude steps used: 18
Number of attitude steps avail: 2927
Mean RA/DEC pixel offset: -62.2971 -30.3780
writing expo file: ad83033000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83033000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83033000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 325 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 325 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
325 325 0 0 0 0
in 2373.49 seconds
Image has 325 counts for 0.1369 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 199 0 0 0 126
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
325 199 0 0 0 126
in 2373.49 seconds
Image has 199 counts for 8.3843E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 126 0 0 0 199
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
325 126 0 0 0 199
in 2373.49 seconds
Image has 126 counts for 5.3086E-02 counts/sec
Command not found; type ? for a command listing
!ad83033000s100202m:ASCA >
!ad83033000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83033000s100202m:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!ad83033000s100202m:ASCA > read events ad83033000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!ad83033000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad83033000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad83033000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100202m.img
Wrote image to file ad83033000s100202m.img
!ad83033000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad83033000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100202m_lo.img
Wrote image to file ad83033000s100202m_lo.img
!ad83033000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad83033000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83033000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83033000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83033000s100202m_hi.img
Wrote image to file ad83033000s100202m_hi.img
!ad83033000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad83033000s000102h.expo ad83033000s000202m.expo ad83033000s100102h.expo ad83033000s100202m.expo-> Summing the following images to produce ad83033000sis32002_all.totsky
ad83033000s000102h.img ad83033000s000202m.img ad83033000s100102h.img ad83033000s100202m.img-> Summing the following images to produce ad83033000sis32002_lo.totsky
ad83033000s000102h_lo.img ad83033000s000202m_lo.img ad83033000s100102h_lo.img ad83033000s100202m_lo.img-> Summing the following images to produce ad83033000sis32002_hi.totsky
ad83033000s000102h_hi.img ad83033000s000202m_hi.img ad83033000s100102h_hi.img ad83033000s100202m_hi.img-> Running XIMAGE to create ad83033000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad83033000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 8.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 8 min: 0 ![2]XIMAGE> read/exp_map ad83033000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 735.028 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 735 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 1839 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 13.0000 13 0 ![9]XIMAGE> exit-> Summing gis images
ad83033000g200170h.expo ad83033000g200270l.expo ad83033000g200370m.expo ad83033000g200470h.expo ad83033000g300170h.expo ad83033000g300270l.expo ad83033000g300370m.expo ad83033000g300470h.expo-> Summing the following images to produce ad83033000gis25670_all.totsky
ad83033000g200170h.img ad83033000g200270l.img ad83033000g200370m.img ad83033000g200470h.img ad83033000g300170h.img ad83033000g300270l.img ad83033000g300370m.img ad83033000g300470h.img-> Summing the following images to produce ad83033000gis25670_lo.totsky
ad83033000g200170h_lo.img ad83033000g200270l_lo.img ad83033000g200370m_lo.img ad83033000g200470h_lo.img ad83033000g300170h_lo.img ad83033000g300270l_lo.img ad83033000g300370m_lo.img ad83033000g300470h_lo.img-> Summing the following images to produce ad83033000gis25670_hi.totsky
ad83033000g200170h_hi.img ad83033000g200270l_hi.img ad83033000g200370m_hi.img ad83033000g200470h_hi.img ad83033000g300170h_hi.img ad83033000g300270l_hi.img ad83033000g300370m_hi.img ad83033000g300470h_hi.img-> Running XIMAGE to create ad83033000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad83033000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 15.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 15 min: 0 ![2]XIMAGE> read/exp_map ad83033000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 812.388 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 812 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 10.00000 100 -1 i,inten,mm,pp 4 25.0000 25 0 ![9]XIMAGE> exit
119 110 0.000173243 115 15 17.4943-> Smoothing ad83033000gis25670_hi.totsky with ad83033000gis25670.totexpo
118 108 8.7807e-05 117 15 15.485-> Smoothing ad83033000gis25670_lo.totsky with ad83033000gis25670.totexpo
119 108 0.000100937 117 14 23.7656-> Determining extraction radii
119 110 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad83033000gis25670.src
139 114 6.62109e-05 91 34 14.7495-> Smoothing ad83033000sis32002_hi.totsky with ad83033000sis32002.totexpo
139 117 2.59142e-05 94 35 9.66951-> Smoothing ad83033000sis32002_lo.totsky with ad83033000sis32002.totexpo
139 113 4.535e-05 90 32 18.7494-> Determining extraction radii
139 114 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad83033000sis32002.src
The sum of the selected column is 448.00000 The mean of the selected column is 448.00000 The standard deviation of the selected column is undefined The minimum of selected column is 448.00000 The maximum of selected column is 448.00000 The number of points used in calculation is 1-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 466.00000 The mean of the selected column is 466.00000 The standard deviation of the selected column is undefined The minimum of selected column is 466.00000 The maximum of selected column is 466.00000 The number of points used in calculation is 1-> Converting (556.0,456.0,2.0) to s1 detector coordinates
The sum of the selected column is 440.00000 The mean of the selected column is 440.00000 The standard deviation of the selected column is undefined The minimum of selected column is 440.00000 The maximum of selected column is 440.00000 The number of points used in calculation is 1-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 501.00000 The mean of the selected column is 501.00000 The standard deviation of the selected column is undefined The minimum of selected column is 501.00000 The maximum of selected column is 501.00000 The number of points used in calculation is 1-> Converting (119.0,110.0,2.0) to g2 detector coordinates
The sum of the selected column is 4393.0000 The mean of the selected column is 104.59524 The standard deviation of the selected column is 1.2889687 The minimum of selected column is 103.00000 The maximum of selected column is 107.00000 The number of points used in calculation is 42-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4804.0000 The mean of the selected column is 114.38095 The standard deviation of the selected column is 1.0581249 The minimum of selected column is 113.00000 The maximum of selected column is 116.00000 The number of points used in calculation is 42-> Converting (119.0,110.0,2.0) to g3 detector coordinates
The sum of the selected column is 7838.0000 The mean of the selected column is 110.39437 The standard deviation of the selected column is 0.97802824 The minimum of selected column is 108.00000 The maximum of selected column is 112.00000 The number of points used in calculation is 71-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8175.0000 The mean of the selected column is 115.14085 The standard deviation of the selected column is 1.0322759 The minimum of selected column is 113.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 71
1 ad83033000s000102h.evt 3451 1 ad83033000s000202m.evt 3451-> Fetching SIS0_NOTCHIP0.1
ad83033000s000102h.evt ad83033000s000202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
2 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 369 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 2095 987 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 266 103 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3451 2361 1090 0 0 0
in 22076.84 seconds
Spectrum has 2361 counts for 0.1069 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 22077. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000s010102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > read events ad83033000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad83033000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad83033000s010102_1.pi group=yes
Wrote spectrum to ad83033000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad83033000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 22077. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 24 are grouped by a factor 4 ... 25 - 32 are grouped by a factor 2 ... 33 - 34 are single channels ... 35 - 36 are grouped by a factor 2 ... 37 - 37 are single channels ... 38 - 39 are grouped by a factor 2 ... 40 - 40 are single channels ... 41 - 60 are grouped by a factor 2 ... 61 - 75 are grouped by a factor 3 ... 76 - 79 are grouped by a factor 4 ... 80 - 89 are grouped by a factor 5 ... 90 - 97 are grouped by a factor 8 ... 98 - 104 are grouped by a factor 7 ... 105 - 109 are grouped by a factor 5 ... 110 - 133 are grouped by a factor 8 ... 134 - 144 are grouped by a factor 11 ... 145 - 159 are grouped by a factor 15 ... 160 - 175 are grouped by a factor 16 ... 176 - 192 are grouped by a factor 17 ... 193 - 224 are grouped by a factor 32 ... 225 - 325 are grouped by a factor 101 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83033000s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 40 bins
expanded to 40 by 40 bins
First WMAP bin is at detector pixel 296 312
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.33500E+03
Weighted mean angle from optical axis = 6.505 arcmin
-> Standard Output From STOOL group_event_files:1 ad83033000s000112h.evt 3566 1 ad83033000s000212m.evt 3566-> SIS0_NOTCHIP0.1 already present in current directory
ad83033000s000112h.evt ad83033000s000212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 3178 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 3178 0100
2 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.24E+04 388 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000112h.evt
Total Good Bad: Region Time Phase Cut
3178 2133 1045 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000212m.evt
Total Good Bad: Region Time Phase Cut
388 275 113 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3566 2408 1158 0 0 0
in 22076.84 seconds
Spectrum has 2408 counts for 0.1091 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 22077. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000s010212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad83033000s000212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83033000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad83033000s010212_1.pi group=yes
Wrote spectrum to ad83033000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad83033000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 22077. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 39 are grouped by a factor 7 ... 40 - 45 are grouped by a factor 6 ... 46 - 50 are grouped by a factor 5 ... 51 - 54 are grouped by a factor 4 ... 55 - 60 are grouped by a factor 3 ... 61 - 62 are grouped by a factor 2 ... 63 - 65 are grouped by a factor 3 ... 66 - 69 are grouped by a factor 2 ... 70 - 72 are grouped by a factor 3 ... 73 - 76 are grouped by a factor 2 ... 77 - 79 are grouped by a factor 3 ... 80 - 81 are grouped by a factor 2 ... 82 - 87 are grouped by a factor 3 ... 88 - 89 are grouped by a factor 2 ... 90 - 92 are grouped by a factor 3 ... 93 - 94 are grouped by a factor 2 ... 95 - 115 are grouped by a factor 3 ... 116 - 119 are grouped by a factor 4 ... 120 - 149 are grouped by a factor 5 ... 150 - 158 are grouped by a factor 9 ... 159 - 166 are grouped by a factor 8 ... 167 - 175 are grouped by a factor 9 ... 176 - 188 are grouped by a factor 13 ... 189 - 203 are grouped by a factor 15 ... 204 - 215 are grouped by a factor 12 ... 216 - 229 are grouped by a factor 14 ... 230 - 240 are grouped by a factor 11 ... 241 - 255 are grouped by a factor 15 ... 256 - 277 are grouped by a factor 22 ... 278 - 295 are grouped by a factor 18 ... 296 - 328 are grouped by a factor 33 ... 329 - 363 are grouped by a factor 35 ... 364 - 394 are grouped by a factor 31 ... 395 - 466 are grouped by a factor 72 ... 467 - 662 are grouped by a factor 196 ... 663 - 962 are grouped by a factor 300 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83033000s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 40 bins
expanded to 40 by 40 bins
First WMAP bin is at detector pixel 296 312
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.38000E+03
Weighted mean angle from optical axis = 6.497 arcmin
-> Standard Output From STOOL group_event_files:1 ad83033000s100102h.evt 3068 1 ad83033000s100202m.evt 3068-> Fetching SIS1_NOTCHIP0.1
ad83033000s100102h.evt ad83033000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
2 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 325 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 1893 850 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 220 105 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3068 2113 955 0 0 0
in 22024.84 seconds
Spectrum has 2113 counts for 9.5937E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 22025. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.33105E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000s110102_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > read events ad83033000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad83033000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad83033000s110102_1.pi group=yes
Wrote spectrum to ad83033000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad83033000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 22025. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.33105E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 22 are grouped by a factor 5 ... 23 - 28 are grouped by a factor 3 ... 29 - 60 are grouped by a factor 2 ... 61 - 63 are grouped by a factor 3 ... 64 - 67 are grouped by a factor 4 ... 68 - 70 are grouped by a factor 3 ... 71 - 74 are grouped by a factor 4 ... 75 - 77 are grouped by a factor 3 ... 78 - 83 are grouped by a factor 6 ... 84 - 88 are grouped by a factor 5 ... 89 - 94 are grouped by a factor 6 ... 95 - 102 are grouped by a factor 8 ... 103 - 111 are grouped by a factor 9 ... 112 - 127 are grouped by a factor 8 ... 128 - 138 are grouped by a factor 11 ... 139 - 153 are grouped by a factor 15 ... 154 - 169 are grouped by a factor 16 ... 170 - 187 are grouped by a factor 18 ... 188 - 218 are grouped by a factor 31 ... 219 - 260 are grouped by a factor 42 ... 261 - 395 are grouped by a factor 135 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83033000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 35 bins
expanded to 40 by 35 bins
First WMAP bin is at detector pixel 288 352
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 49.907 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.08100E+03
Weighted mean angle from optical axis = 8.856 arcmin
-> Standard Output From STOOL group_event_files:1 ad83033000s100112h.evt 3147 1 ad83033000s100212m.evt 3147-> SIS1_NOTCHIP0.1 already present in current directory
ad83033000s100112h.evt ad83033000s100212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 2813 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 2813 0001
2 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.24E+04 334 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100112h.evt
Total Good Bad: Region Time Phase Cut
2813 1917 896 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100212m.evt
Total Good Bad: Region Time Phase Cut
334 225 109 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3147 2142 1005 0 0 0
in 22024.84 seconds
Spectrum has 2142 counts for 9.7254E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 22025. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.33105E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000s110212_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad83033000s100212m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83033000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad83033000s110212_1.pi group=yes
Wrote spectrum to ad83033000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad83033000s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 22025. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.33105E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 35 are grouped by a factor 10 ... 36 - 44 are grouped by a factor 9 ... 45 - 50 are grouped by a factor 6 ... 51 - 55 are grouped by a factor 5 ... 56 - 76 are grouped by a factor 3 ... 77 - 78 are grouped by a factor 2 ... 79 - 105 are grouped by a factor 3 ... 106 - 121 are grouped by a factor 4 ... 122 - 126 are grouped by a factor 5 ... 127 - 132 are grouped by a factor 6 ... 133 - 139 are grouped by a factor 7 ... 140 - 151 are grouped by a factor 6 ... 152 - 158 are grouped by a factor 7 ... 159 - 168 are grouped by a factor 10 ... 169 - 177 are grouped by a factor 9 ... 178 - 188 are grouped by a factor 11 ... 189 - 203 are grouped by a factor 15 ... 204 - 219 are grouped by a factor 16 ... 220 - 234 are grouped by a factor 15 ... 235 - 248 are grouped by a factor 14 ... 249 - 269 are grouped by a factor 21 ... 270 - 289 are grouped by a factor 20 ... 290 - 328 are grouped by a factor 39 ... 329 - 365 are grouped by a factor 37 ... 366 - 411 are grouped by a factor 46 ... 412 - 487 are grouped by a factor 76 ... 488 - 707 are grouped by a factor 220 ... 708 - 881 are grouped by a factor 174 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83033000s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 35 bins
expanded to 40 by 35 bins
First WMAP bin is at detector pixel 288 352
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 49.907 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.10700E+03
Weighted mean angle from optical axis = 8.862 arcmin
-> Standard Output From STOOL group_event_files:1 ad83033000g200170h.evt 7543 1 ad83033000g200270l.evt 7543 1 ad83033000g200370m.evt 7543 1 ad83033000g200470h.evt 7543-> GIS2_REGION256.4 already present in current directory
ad83033000g200170h.evt ad83033000g200270l.evt ad83033000g200370m.evt ad83033000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 705 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 1382 4871 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 1 8 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 146 430 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 159 546 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7543 1688 5855 0 0 0
in 24373.64 seconds
Spectrum has 1688 counts for 6.9255E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 24374. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200270l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad83033000g210170_1.pi group=yes
Wrote spectrum to ad83033000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad83033000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83033000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 24374. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 38 are grouped by a factor 39 ... 39 - 62 are grouped by a factor 24 ... 63 - 74 are grouped by a factor 12 ... 75 - 81 are grouped by a factor 7 ... 82 - 93 are grouped by a factor 6 ... 94 - 101 are grouped by a factor 8 ... 102 - 105 are grouped by a factor 4 ... 106 - 110 are grouped by a factor 5 ... 111 - 114 are grouped by a factor 4 ... 115 - 120 are grouped by a factor 6 ... 121 - 124 are grouped by a factor 4 ... 125 - 148 are grouped by a factor 6 ... 149 - 155 are grouped by a factor 7 ... 156 - 160 are grouped by a factor 5 ... 161 - 168 are grouped by a factor 8 ... 169 - 174 are grouped by a factor 6 ... 175 - 188 are grouped by a factor 7 ... 189 - 197 are grouped by a factor 9 ... 198 - 205 are grouped by a factor 8 ... 206 - 217 are grouped by a factor 12 ... 218 - 231 are grouped by a factor 14 ... 232 - 246 are grouped by a factor 15 ... 247 - 263 are grouped by a factor 17 ... 264 - 274 are grouped by a factor 11 ... 275 - 292 are grouped by a factor 18 ... 293 - 311 are grouped by a factor 19 ... 312 - 332 are grouped by a factor 21 ... 333 - 364 are grouped by a factor 32 ... 365 - 397 are grouped by a factor 33 ... 398 - 431 are grouped by a factor 34 ... 432 - 472 are grouped by a factor 41 ... 473 - 520 are grouped by a factor 48 ... 521 - 615 are grouped by a factor 95 ... 616 - 763 are grouped by a factor 148 ... 764 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 43 52
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.68800E+03
Weighted mean angle from optical axis = 8.563 arcmin
-> Standard Output From STOOL group_event_files:1 ad83033000g300170h.evt 8356 1 ad83033000g300270l.evt 8356 1 ad83033000g300370m.evt 8356 1 ad83033000g300470h.evt 8356-> GIS3_REGION256.4 already present in current directory
ad83033000g300170h.evt ad83033000g300270l.evt ad83033000g300370m.evt ad83033000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 667 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 1832 5177 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 5 12 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 183 480 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 188 479 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8356 2208 6148 0 0 0
in 24369.64 seconds
Spectrum has 2208 counts for 9.0605E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 24370. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300270l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad83033000g310170_1.pi group=yes
Wrote spectrum to ad83033000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad83033000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83033000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 24370. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 40 are grouped by a factor 41 ... 41 - 57 are grouped by a factor 17 ... 58 - 68 are grouped by a factor 11 ... 69 - 82 are grouped by a factor 7 ... 83 - 92 are grouped by a factor 5 ... 93 - 108 are grouped by a factor 4 ... 109 - 111 are grouped by a factor 3 ... 112 - 127 are grouped by a factor 4 ... 128 - 130 are grouped by a factor 3 ... 131 - 150 are grouped by a factor 4 ... 151 - 160 are grouped by a factor 5 ... 161 - 164 are grouped by a factor 4 ... 165 - 169 are grouped by a factor 5 ... 170 - 193 are grouped by a factor 6 ... 194 - 200 are grouped by a factor 7 ... 201 - 209 are grouped by a factor 9 ... 210 - 221 are grouped by a factor 12 ... 222 - 231 are grouped by a factor 10 ... 232 - 255 are grouped by a factor 12 ... 256 - 269 are grouped by a factor 14 ... 270 - 284 are grouped by a factor 15 ... 285 - 300 are grouped by a factor 16 ... 301 - 315 are grouped by a factor 15 ... 316 - 331 are grouped by a factor 16 ... 332 - 371 are grouped by a factor 20 ... 372 - 394 are grouped by a factor 23 ... 395 - 419 are grouped by a factor 25 ... 420 - 446 are grouped by a factor 27 ... 447 - 472 are grouped by a factor 26 ... 473 - 516 are grouped by a factor 44 ... 517 - 586 are grouped by a factor 70 ... 587 - 667 are grouped by a factor 81 ... 668 - 826 are grouped by a factor 159 ... 827 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83033000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 48 53
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.20800E+03
Weighted mean angle from optical axis = 6.158 arcmin
-> Plotting ad83033000g210170_1_pi.ps from ad83033000g210170_1.pi
XSPEC 9.01 23:57:18 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000g210170_1.pi
Net count rate (cts/s) for file 1 6.9255E-02+/- 1.7968E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83033000g310170_1_pi.ps from ad83033000g310170_1.pi
XSPEC 9.01 23:57:32 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000g310170_1.pi
Net count rate (cts/s) for file 1 9.0605E-02+/- 2.0019E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83033000s010102_1_pi.ps from ad83033000s010102_1.pi
XSPEC 9.01 23:57:45 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000s010102_1.pi
Net count rate (cts/s) for file 1 0.1069 +/- 2.2065E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83033000s010212_1_pi.ps from ad83033000s010212_1.pi
XSPEC 9.01 23:57:59 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000s010212_1.pi
Net count rate (cts/s) for file 1 0.1091 +/- 2.2343E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83033000s110102_1_pi.ps from ad83033000s110102_1.pi
XSPEC 9.01 23:58:15 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000s110102_1.pi
Net count rate (cts/s) for file 1 9.5937E-02+/- 2.0925E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83033000s110212_1_pi.ps from ad83033000s110212_1.pi
XSPEC 9.01 23:58:30 26-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83033000s110212_1.pi
Net count rate (cts/s) for file 1 9.7254E-02+/- 2.1121E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
2 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 369 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 2095 987 0 0 0
Writing events file
2095 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 266 103 0 0 0
Writing events file
2361 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3451 2361 1090 0 0 0
in 22076.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > read events ad83033000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad83033000s000002_1.lc with binsize 467.53158461727
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:03:47 0.22E+05 2361 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/events.tmp
Total Good Bad: Region Time Phase Cut
2361 2361 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2361 2361 0 0 0 0
in 22076.84 seconds
Fits light curve has 2361 counts for 0.1069 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > set binsize 467.53158461727
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad83033000s000002_1.lc
Wrote FITS light curve to file ad83033000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad83033000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83033000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A1895 Start Time (d) .... 9801 00:37:45.627
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9801 15:23:37.627
No. of Rows ....... 50 Bin Time (s) ...... 467.5
Right Ascension ... 2.1339E+02 Internal time sys.. Converted to TJD
Declination ....... 7.1392E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 114 Newbins of 467.532 (s)
Intv 1 Start 9801 0:41:39
Ser.1 Avg 0.1064 Chisq 51.76 Var 0.2811E-03 Newbs. 50
Min 0.7577E-01 Max 0.1504 expVar 0.2716E-03 Bins 50
Results from Statistical Analysis
Newbin Integration Time (s).. 467.53
Interval Duration (s)........ 52831.
No. of Newbins .............. 50
Average (c/s) ............... 0.10638 +/- 0.24E-02
Standard Deviation (c/s)..... 0.16766E-01
Minimum (c/s)................ 0.75769E-01
Maximum (c/s)................ 0.15045
Variance ((c/s)**2).......... 0.28111E-03 +/- 0.57E-04
Expected Variance ((c/s)**2). 0.27156E-03 +/- 0.55E-04
Third Moment ((c/s)**3)...... 0.24326E-05
Average Deviation (c/s)...... 0.14088E-01
Skewness..................... 0.51613 +/- 0.35
Kurtosis.....................-0.34661 +/- 0.69
RMS fractional variation....< 0.12778 (3 sigma)
Chi-Square................... 51.758 dof 49
Chi-Square Prob of constancy. 0.36672 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.30504 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 114 Newbins of 467.532 (s)
Intv 1 Start 9801 0:41:39
Ser.1 Avg 0.1064 Chisq 51.76 Var 0.2811E-03 Newbs. 50
Min 0.7577E-01 Max 0.1504 expVar 0.2716E-03 Bins 50
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=4.0000000000E+00 for ad83033000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
2 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 325 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 1899 844 0 0 0
Writing events file
1899 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 221 104 0 0 0
Writing events file
2120 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3068 2120 948 0 0 0
in 22024.84 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > read events ad83033000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad83033000s100002_1.lc with binsize 519.453806508473
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:03:47 0.22E+05 2120 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/events.tmp
Total Good Bad: Region Time Phase Cut
2120 2120 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2120 2120 0 0 0 0
in 22024.84 seconds
Fits light curve has 2120 counts for 9.6255E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > set binsize 519.453806508473
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad83033000s100002_1.lc
Wrote FITS light curve to file ad83033000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad83033000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83033000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A1895 Start Time (d) .... 9801 00:37:45.627
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9801 15:23:37.627
No. of Rows ....... 43 Bin Time (s) ...... 519.5
Right Ascension ... 2.1339E+02 Internal time sys.. Converted to TJD
Declination ....... 7.1392E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 103 Newbins of 519.454 (s)
Intv 1 Start 9801 0:42: 5
Ser.1 Avg 0.9778E-01 Chisq 50.80 Var 0.2591E-03 Newbs. 43
Min 0.7241E-01 Max 0.1498 expVar 0.2193E-03 Bins 43
Results from Statistical Analysis
Newbin Integration Time (s).. 519.45
Interval Duration (s)........ 52465.
No. of Newbins .............. 43
Average (c/s) ............... 0.97783E-01 +/- 0.23E-02
Standard Deviation (c/s)..... 0.16096E-01
Minimum (c/s)................ 0.72405E-01
Maximum (c/s)................ 0.14976
Variance ((c/s)**2).......... 0.25908E-03 +/- 0.57E-04
Expected Variance ((c/s)**2). 0.21928E-03 +/- 0.48E-04
Third Moment ((c/s)**3)...... 0.34282E-05
Average Deviation (c/s)...... 0.12555E-01
Skewness..................... 0.82209 +/- 0.37
Kurtosis..................... 0.95264 +/- 0.75
RMS fractional variation....< 0.11748 (3 sigma)
Chi-Square................... 50.803 dof 42
Chi-Square Prob of constancy. 0.16549 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.12569 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 103 Newbins of 519.454 (s)
Intv 1 Start 9801 0:42: 5
Ser.1 Avg 0.9778E-01 Chisq 50.80 Var 0.2591E-03 Newbs. 43
Min 0.7241E-01 Max 0.1498 expVar 0.2193E-03 Bins 43
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad83033000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 705 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 1382 4871 0 0 0
Writing events file
1382 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 1 8 0 0 0
Writing events file
1383 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 146 430 0 0 0
Writing events file
1529 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 159 546 0 0 0
Writing events file
1688 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7543 1688 5855 0 0 0
in 24373.64 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200270l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad83033000g200070_1.lc with binsize 721.968032518993
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:03:53 0.24E+05 1688 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/events.tmp
Total Good Bad: Region Time Phase Cut
1688 1688 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1688 1688 0 0 0 0
in 24373.64 seconds
Fits light curve has 1688 counts for 6.9255E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > set binsize 721.968032518993
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad83033000g200070_1.lc
Wrote FITS light curve to file ad83033000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad83033000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83033000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A1895 Start Time (d) .... 9801 00:37:45.627
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9801 15:26:17.627
No. of Rows ....... 35 Bin Time (s) ...... 722.0
Right Ascension ... 2.1339E+02 Internal time sys.. Converted to TJD
Declination ....... 7.1392E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 74 Newbins of 721.968 (s)
Intv 1 Start 9801 0:43:46
Ser.1 Avg 0.6917E-01 Chisq 34.50 Var 0.1134E-03 Newbs. 35
Min 0.4748E-01 Max 0.1021 expVar 0.1150E-03 Bins 35
Results from Statistical Analysis
Newbin Integration Time (s).. 721.97
Interval Duration (s)........ 52704.
No. of Newbins .............. 35
Average (c/s) ............... 0.69170E-01 +/- 0.18E-02
Standard Deviation (c/s)..... 0.10648E-01
Minimum (c/s)................ 0.47476E-01
Maximum (c/s)................ 0.10212
Variance ((c/s)**2).......... 0.11338E-03 +/- 0.27E-04
Expected Variance ((c/s)**2). 0.11503E-03 +/- 0.28E-04
Third Moment ((c/s)**3)...... 0.73440E-06
Average Deviation (c/s)...... 0.77863E-02
Skewness..................... 0.60830 +/- 0.41
Kurtosis..................... 1.1668 +/- 0.83
RMS fractional variation....< 0.14707 (3 sigma)
Chi-Square................... 34.498 dof 34
Chi-Square Prob of constancy. 0.44386 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.43824E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 74 Newbins of 721.968 (s)
Intv 1 Start 9801 0:43:46
Ser.1 Avg 0.6917E-01 Chisq 34.50 Var 0.1134E-03 Newbs. 35
Min 0.4748E-01 Max 0.1021 expVar 0.1150E-03 Bins 35
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad83033000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 667 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 1832 5177 0 0 0
Writing events file
1832 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 5 12 0 0 0
Writing events file
1837 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 183 480 0 0 0
Writing events file
2020 events written to the output file
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 188 479 0 0 0
Writing events file
2208 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8356 2208 6148 0 0 0
in 24369.64 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300270l.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300370m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad83033000g300070_1.lc with binsize 551.848749927097
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:03:53 0.24E+05 2208 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/events.tmp
Total Good Bad: Region Time Phase Cut
2208 2208 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2208 2208 0 0 0 0
in 24369.64 seconds
Fits light curve has 2208 counts for 9.0605E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > set binsize 551.848749927097
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad83033000g300070_1.lc
Wrote FITS light curve to file ad83033000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad83033000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83033000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A1895 Start Time (d) .... 9801 00:37:45.627
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9801 15:26:17.627
No. of Rows ....... 46 Bin Time (s) ...... 551.8
Right Ascension ... 2.1339E+02 Internal time sys.. Converted to TJD
Declination ....... 7.1392E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 97 Newbins of 551.849 (s)
Intv 1 Start 9801 0:42:21
Ser.1 Avg 0.9034E-01 Chisq 51.51 Var 0.2237E-03 Newbs. 46
Min 0.5346E-01 Max 0.1305 expVar 0.1998E-03 Bins 46
Results from Statistical Analysis
Newbin Integration Time (s).. 551.85
Interval Duration (s)........ 52977.
No. of Newbins .............. 46
Average (c/s) ............... 0.90344E-01 +/- 0.21E-02
Standard Deviation (c/s)..... 0.14957E-01
Minimum (c/s)................ 0.53462E-01
Maximum (c/s)................ 0.13047
Variance ((c/s)**2).......... 0.22371E-03 +/- 0.47E-04
Expected Variance ((c/s)**2). 0.19977E-03 +/- 0.42E-04
Third Moment ((c/s)**3)......-0.43306E-06
Average Deviation (c/s)...... 0.11434E-01
Skewness.....................-0.12943 +/- 0.36
Kurtosis..................... 0.54982 +/- 0.72
RMS fractional variation....< 0.12443 (3 sigma)
Chi-Square................... 51.512 dof 45
Chi-Square Prob of constancy. 0.23415 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.38967 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 97 Newbins of 551.849 (s)
Intv 1 Start 9801 0:42:21
Ser.1 Avg 0.9034E-01 Chisq 51.51 Var 0.2237E-03 Newbs. 46
Min 0.5346E-01 Max 0.1305 expVar 0.1998E-03 Bins 46
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad83033000g200170h.evt[2] ad83033000g200270l.evt[2] ad83033000g200370m.evt[2] ad83033000g200470h.evt[2]-> Making L1 light curve of ft950325_0003_1531G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 43835 output records from 43879 good input G2_L1 records.-> Making L1 light curve of ft950325_0003_1531G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 21654 output records from 45677 good input G2_L1 records.-> Merging GTIs from the following files:
ad83033000g300170h.evt[2] ad83033000g300270l.evt[2] ad83033000g300370m.evt[2] ad83033000g300470h.evt[2]-> Making L1 light curve of ft950325_0003_1531G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 41698 output records from 41743 good input G3_L1 records.-> Making L1 light curve of ft950325_0003_1531G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 21265 output records from 43496 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 6253 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.evt
Total Good Bad: Region Time Phase Cut
6253 1382 4871 0 0 0
Writing events file
1382 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6253 1382 4871 0 0 0
in 20265.51 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83033000g200170h_1.ulc use_events=yes
Wrote events list to file ad83033000g200170h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000g200270l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 9 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.evt
Total Good Bad: Region Time Phase Cut
9 1 8 0 0 0
Writing events file
1 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9 1 8 0 0 0
in 31.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200270l.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83033000g200270l_1.ulc use_events=yes
Wrote events list to file ad83033000g200270l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad83033000g200270l_1.ulc since it has 1 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 576 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.evt
Total Good Bad: Region Time Phase Cut
576 146 430 0 0 0
Writing events file
146 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
576 146 430 0 0 0
in 2047.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200370m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83033000g200370m_1.ulc use_events=yes
Wrote events list to file ad83033000g200370m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000g200470h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 705 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.evt
Total Good Bad: Region Time Phase Cut
705 159 546 0 0 0
Writing events file
159 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
705 159 546 0 0 0
in 2028.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region ad83033000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83033000g200470h_1.ulc use_events=yes
Wrote events list to file ad83033000g200470h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.20E+05 7009 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.evt
Total Good Bad: Region Time Phase Cut
7009 1832 5177 0 0 0
Writing events file
1832 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7009 1832 5177 0 0 0
in 20261.51 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83033000g300170h_1.ulc use_events=yes
Wrote events list to file ad83033000g300170h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000g300270l_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.32E+02 17 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.evt
Total Good Bad: Region Time Phase Cut
17 5 12 0 0 0
Writing events file
5 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17 5 12 0 0 0
in 31.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300270l.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83033000g300270l_1.ulc use_events=yes
Wrote events list to file ad83033000g300270l_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad83033000g300270l_1.ulc since it has 5 events
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.20E+04 663 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.evt
Total Good Bad: Region Time Phase Cut
663 183 480 0 0 0
Writing events file
183 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
663 183 480 0 0 0
in 2047.99 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300370m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83033000g300370m_1.ulc use_events=yes
Wrote events list to file ad83033000g300370m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000g300470h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.20E+04 667 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.evt
Total Good Bad: Region Time Phase Cut
667 188 479 0 0 0
Writing events file
188 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
667 188 479 0 0 0
in 2028.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region ad83033000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83033000g300470h_1.ulc use_events=yes
Wrote events list to file ad83033000g300470h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83033000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 3082 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000102h.evt
Total Good Bad: Region Time Phase Cut
3082 2095 987 0 0 0
Writing events file
2095 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3082 2095 987 0 0 0
in 19703.35 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad83033000s000102h_1.ulc use_events=yes
Wrote events list to file ad83033000s000102h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83033000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 3178 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000112h.evt
Total Good Bad: Region Time Phase Cut
3178 2133 1045 0 0 0
Writing events file
2133 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3178 2133 1045 0 0 0
in 19703.35 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad83033000s000112h_1.ulc use_events=yes
Wrote events list to file ad83033000s000112h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad83033000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 369 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000202m.evt
Total Good Bad: Region Time Phase Cut
369 266 103 0 0 0
Writing events file
266 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
369 266 103 0 0 0
in 2373.49 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad83033000s000202m_1.ulc use_events=yes
Wrote events list to file ad83033000s000202m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83033000s000212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.24E+04 388 0100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s000212m.evt
Total Good Bad: Region Time Phase Cut
388 275 113 0 0 0
Writing events file
275 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
388 275 113 0 0 0
in 2373.49 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s000212m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83033000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad83033000s000212m_1.ulc use_events=yes
Wrote events list to file ad83033000s000212m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad83033000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.20E+05 2743 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100102h.evt
Total Good Bad: Region Time Phase Cut
2743 1899 844 0 0 0
Writing events file
1899 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2743 1899 844 0 0 0
in 19651.35 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad83033000s100102h_1.ulc use_events=yes
Wrote events list to file ad83033000s100102h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83033000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.20E+05 2813 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100112h.evt
Total Good Bad: Region Time Phase Cut
2813 1924 889 0 0 0
Writing events file
1924 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2813 1924 889 0 0 0
in 19651.35 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad83033000s100112h_1.ulc use_events=yes
Wrote events list to file ad83033000s100112h_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad83033000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.24E+04 325 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100202m.evt
Total Good Bad: Region Time Phase Cut
325 221 104 0 0 0
Writing events file
221 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
325 221 104 0 0 0
in 2373.49 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad83033000s100202m_1.ulc use_events=yes
Wrote events list to file ad83033000s100202m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83033000s100212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.24E+04 334 0001
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000s100212m.evt
Total Good Bad: Region Time Phase Cut
334 226 108 0 0 0
Writing events file
226 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
334 226 108 0 0 0
in 2373.49 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83033000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad83033000s100212m_1.ulc use_events=yes
Wrote events list to file ad83033000s100212m_1.ulc
Changing Data directory from:
/data/data23/seq_proc/83033000.006/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 16939 Total of 0 sets of frame data are extracted.
1 ad83033000g200170h.unf 41395 1 ad83033000g200270l.unf 41395 1 ad83033000g200370m.unf 41395 1 ad83033000g200470h.unf 41395-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4446 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4446 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2221 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.unf
Total Good Bad: Region Time Phase Cut
27894 6544 21350 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.unf
Total Good Bad: Region Time Phase Cut
6834 756 6078 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.unf
Total Good Bad: Region Time Phase Cut
4446 1086 3360 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.unf
Total Good Bad: Region Time Phase Cut
2221 565 1656 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
41395 8951 32444 0 0 0
in 35275.89 seconds
Spectrum has 8951 counts for 0.2537 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35276. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200370m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > read events ad83033000g200470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad83033000g220170.cal group=yes
Wrote spectrum to ad83033000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 00:17:51 27-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad83033000g220170.cal
Net count rate (cts/s) for file 1 0.2537 +/- 2.6830E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.6894E+05 using 84 PHA bins.
Reduced chi-squared = 1.1285E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.6293E+05 using 84 PHA bins.
Reduced chi-squared = 1.1063E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.6293E+05 using 84 PHA bins.
Reduced chi-squared = 1.0923E+04
!XSPEC> renorm
Chi-Squared = 2590. using 84 PHA bins.
Reduced chi-squared = 32.79
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2007.7 0 1.000 5.893 0.1081 7.6561E-02
6.6973E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
720.97 0 1.000 5.862 0.1598 0.1158
5.8855E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
252.01 -1 1.000 5.905 0.1755 0.1626
4.0015E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
219.78 -2 1.000 5.934 0.1909 0.1783
2.9411E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
218.21 -3 1.000 5.927 0.1846 0.1760
3.1681E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
218.18 -4 1.000 5.929 0.1856 0.1767
3.1037E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
218.15 -5 1.000 5.928 0.1852 0.1765
3.1203E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
218.15 2 1.000 5.928 0.1852 0.1765
3.1203E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92821 +/- 0.61018E-02
3 3 2 gaussian/b Sigma 0.185210 +/- 0.64172E-02
4 4 2 gaussian/b norm 0.176492 +/- 0.29144E-02
5 2 3 gaussian/b LineE 6.52698 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.194338 = par 3 * 1.0493
7 5 3 gaussian/b norm 3.120348E-02 +/- 0.20593E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 218.2 using 84 PHA bins.
Reduced chi-squared = 2.761
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad83033000g220170.cal peaks at 5.92821 +/- 0.0061018 keV1 ad83033000g300170h.unf 40520 1 ad83033000g300270l.unf 40520 1 ad83033000g300370m.unf 40520 1 ad83033000g300470h.unf 40520-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4167 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
2 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
3 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4167 1024
4 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2049 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.unf
Total Good Bad: Region Time Phase Cut
27484 6067 21417 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.unf
Total Good Bad: Region Time Phase Cut
6820 666 6154 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.unf
Total Good Bad: Region Time Phase Cut
4167 944 3223 0 0 0
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.unf
Total Good Bad: Region Time Phase Cut
2049 527 1522 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
40520 8204 32316 0 0 0
in 35259.89 seconds
Spectrum has 8204 counts for 0.2327 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35260. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83033000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!xsel:ASCA > read events ad83033000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300270l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300370m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > read events ad83033000g300470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad83033000g320170.cal group=yes
Wrote spectrum to ad83033000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 00:18:53 27-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad83033000g320170.cal
Net count rate (cts/s) for file 1 0.2327 +/- 2.5708E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.5803E+05 using 84 PHA bins.
Reduced chi-squared = 1.2442E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.4983E+05 using 84 PHA bins.
Reduced chi-squared = 1.2177E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.4983E+05 using 84 PHA bins.
Reduced chi-squared = 1.2023E+04
!XSPEC> renorm
Chi-Squared = 2726. using 84 PHA bins.
Reduced chi-squared = 34.51
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2182.1 0 1.000 5.893 8.8844E-02 7.1590E-02
6.1444E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
832.10 0 1.000 5.867 0.1348 0.1124
5.2816E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
223.93 -1 1.000 5.922 0.1458 0.1606
3.3376E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
161.37 -2 1.000 5.952 0.1570 0.1785
2.3581E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
159.94 -3 1.000 5.948 0.1513 0.1775
2.4707E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
159.91 -4 1.000 5.948 0.1513 0.1776
2.4574E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
159.90 -5 1.000 5.948 0.1512 0.1776
2.4593E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94829 +/- 0.47477E-02
3 3 2 gaussian/b Sigma 0.151210 +/- 0.59445E-02
4 4 2 gaussian/b norm 0.177606 +/- 0.26186E-02
5 2 3 gaussian/b LineE 6.54910 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.158663 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.459279E-02 +/- 0.15416E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 159.9 using 84 PHA bins.
Reduced chi-squared = 2.024
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad83033000g320170.cal peaks at 5.94829 +/- 0.0047477 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.31E+05 16365 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad83033000s000102h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.31E+05 17379 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT2 > Session saved, goodbye
-> ad83033000s000112h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.63E+04 1932 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT > Session saved, goodbye
-> ad83033000s000202m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.63E+04 2015 0100
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s000212m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS0-BRIGHT2 > Session saved, goodbye
-> ad83033000s000212m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT HIGH 25/03/95 00:45:55 0.31E+05 71293 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad83033000s100102h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 HIGH 25/03/95 00:45:55 0.31E+05 72040 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT2 > Session saved, goodbye
-> ad83033000s100112h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT MEDIUM 25/03/95 00:03:47 0.63E+04 10744 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad83033000s100202m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 MEDIUM 25/03/95 00:03:47 0.63E+04 10793 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT2 > Session saved, goodbye
-> ad83033000s100212m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT LOW 25/03/95 02:40:19 0.29E+04 1565 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT > Session saved, goodbye
-> ad83033000s100302l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A1895 BRIGHT2 LOW 25/03/95 02:40:19 0.29E+04 1571 0001
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 4.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-SIS1-BRIGHT2 > Session saved, goodbye
-> ad83033000s100312l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad83033000g200170h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27894 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200170h.unf
Total Good Bad: Region Time Phase Cut
27894 5495 0 22399 0 0
Writing events file
5495 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27894 5495 0 22399 0 0
in 2286.54 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g200270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad83033000g200270l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6834 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200270l.unf
Total Good Bad: Region Time Phase Cut
6834 6219 0 615 0 0
Writing events file
6219 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6834 6219 0 615 0 0
in 2080.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200270l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g200370m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4446 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad83033000g200370m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4446 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200370m.unf
Total Good Bad: Region Time Phase Cut
4446 595 0 3851 0 0
Writing events file
595 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4446 595 0 3851 0 0
in 256.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200370m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g200470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2221 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS2-PH > Session saved, goodbye
-> ad83033000g200470h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2221 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g200470h.unf
Total Good Bad: Region Time Phase Cut
2221 90 0 2131 0 0
Writing events file
90 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2221 90 0 2131 0 0
in 63.82 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad83033000g300170h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 00:46:07 0.26E+05 27484 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300170h.unf
Total Good Bad: Region Time Phase Cut
27484 5504 0 21980 0 0
Writing events file
5504 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
27484 5504 0 21980 0 0
in 2278.54 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g300270l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad83033000g300270l.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH LOW 25/03/95 02:40:25 0.24E+04 6820 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300270l.unf
Total Good Bad: Region Time Phase Cut
6820 6192 0 628 0 0
Writing events file
6192 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6820 6192 0 628 0 0
in 2080.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300270l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g300370m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4167 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad83033000g300370m.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH MEDIUM 25/03/95 00:03:53 0.46E+04 4167 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300370m.unf
Total Good Bad: Region Time Phase Cut
4167 628 0 3539 0 0
Writing events file
628 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4167 628 0 3539 0 0
in 256.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300370m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83033000g300470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2049 1024
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
The selection criteria produced no GTI's
Failed to get mkf_exp
XSL_SELECT: Status = -10
earthevents:ASCA-GIS3-PH > Session saved, goodbye
-> ad83033000g300470h.drk not created
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A1895 PH HIGH 25/03/95 14:51:53 0.23E+04 2049 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data23/seq_proc/83033000.006/ad83033000g300470h.unf
Total Good Bad: Region Time Phase Cut
2049 101 0 1948 0 0
Writing events file
101 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2049 101 0 1948 0 0
in 63.82 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data23/seq_proc/83033000.006/
Setting mkf directory to /data/data23/seq_proc/83033000.006/
!earthevents:ASCA > read events ad83033000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data23/seq_proc/83033000.006/
HK Directory is: /data/data23/seq_proc/83033000.006/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad83033000g200170h.unf|CPU2|RUN|CPU2 run/stop ad83033000g200470h.unf|CPU2|STOP|CPU2 run/stop ad83033000g200170h.unf|CPU3|RUN|CPU3 run/stop ad83033000g200470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad83033000g200170h.unf
ad83033000g300170h.unf|CPU2|RUN|CPU2 run/stop ad83033000g300470h.unf|CPU2|STOP|CPU2 run/stop ad83033000g300170h.unf|CPU3|RUN|CPU3 run/stop ad83033000g300470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad83033000g300170h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files